Loading...
1/* SPDX-License-Identifier: GPL-2.0-only */
2#ifndef __NET_CFG80211_H
3#define __NET_CFG80211_H
4/*
5 * 802.11 device and configuration interface
6 *
7 * Copyright 2006-2010 Johannes Berg <johannes@sipsolutions.net>
8 * Copyright 2013-2014 Intel Mobile Communications GmbH
9 * Copyright 2015-2017 Intel Deutschland GmbH
10 * Copyright (C) 2018-2021 Intel Corporation
11 */
12
13#include <linux/ethtool.h>
14#include <uapi/linux/rfkill.h>
15#include <linux/netdevice.h>
16#include <linux/debugfs.h>
17#include <linux/list.h>
18#include <linux/bug.h>
19#include <linux/netlink.h>
20#include <linux/skbuff.h>
21#include <linux/nl80211.h>
22#include <linux/if_ether.h>
23#include <linux/ieee80211.h>
24#include <linux/net.h>
25#include <linux/rfkill.h>
26#include <net/regulatory.h>
27
28/**
29 * DOC: Introduction
30 *
31 * cfg80211 is the configuration API for 802.11 devices in Linux. It bridges
32 * userspace and drivers, and offers some utility functionality associated
33 * with 802.11. cfg80211 must, directly or indirectly via mac80211, be used
34 * by all modern wireless drivers in Linux, so that they offer a consistent
35 * API through nl80211. For backward compatibility, cfg80211 also offers
36 * wireless extensions to userspace, but hides them from drivers completely.
37 *
38 * Additionally, cfg80211 contains code to help enforce regulatory spectrum
39 * use restrictions.
40 */
41
42
43/**
44 * DOC: Device registration
45 *
46 * In order for a driver to use cfg80211, it must register the hardware device
47 * with cfg80211. This happens through a number of hardware capability structs
48 * described below.
49 *
50 * The fundamental structure for each device is the 'wiphy', of which each
51 * instance describes a physical wireless device connected to the system. Each
52 * such wiphy can have zero, one, or many virtual interfaces associated with
53 * it, which need to be identified as such by pointing the network interface's
54 * @ieee80211_ptr pointer to a &struct wireless_dev which further describes
55 * the wireless part of the interface, normally this struct is embedded in the
56 * network interface's private data area. Drivers can optionally allow creating
57 * or destroying virtual interfaces on the fly, but without at least one or the
58 * ability to create some the wireless device isn't useful.
59 *
60 * Each wiphy structure contains device capability information, and also has
61 * a pointer to the various operations the driver offers. The definitions and
62 * structures here describe these capabilities in detail.
63 */
64
65struct wiphy;
66
67/*
68 * wireless hardware capability structures
69 */
70
71/**
72 * enum ieee80211_channel_flags - channel flags
73 *
74 * Channel flags set by the regulatory control code.
75 *
76 * @IEEE80211_CHAN_DISABLED: This channel is disabled.
77 * @IEEE80211_CHAN_NO_IR: do not initiate radiation, this includes
78 * sending probe requests or beaconing.
79 * @IEEE80211_CHAN_RADAR: Radar detection is required on this channel.
80 * @IEEE80211_CHAN_NO_HT40PLUS: extension channel above this channel
81 * is not permitted.
82 * @IEEE80211_CHAN_NO_HT40MINUS: extension channel below this channel
83 * is not permitted.
84 * @IEEE80211_CHAN_NO_OFDM: OFDM is not allowed on this channel.
85 * @IEEE80211_CHAN_NO_80MHZ: If the driver supports 80 MHz on the band,
86 * this flag indicates that an 80 MHz channel cannot use this
87 * channel as the control or any of the secondary channels.
88 * This may be due to the driver or due to regulatory bandwidth
89 * restrictions.
90 * @IEEE80211_CHAN_NO_160MHZ: If the driver supports 160 MHz on the band,
91 * this flag indicates that an 160 MHz channel cannot use this
92 * channel as the control or any of the secondary channels.
93 * This may be due to the driver or due to regulatory bandwidth
94 * restrictions.
95 * @IEEE80211_CHAN_INDOOR_ONLY: see %NL80211_FREQUENCY_ATTR_INDOOR_ONLY
96 * @IEEE80211_CHAN_IR_CONCURRENT: see %NL80211_FREQUENCY_ATTR_IR_CONCURRENT
97 * @IEEE80211_CHAN_NO_20MHZ: 20 MHz bandwidth is not permitted
98 * on this channel.
99 * @IEEE80211_CHAN_NO_10MHZ: 10 MHz bandwidth is not permitted
100 * on this channel.
101 * @IEEE80211_CHAN_NO_HE: HE operation is not permitted on this channel.
102 * @IEEE80211_CHAN_1MHZ: 1 MHz bandwidth is permitted
103 * on this channel.
104 * @IEEE80211_CHAN_2MHZ: 2 MHz bandwidth is permitted
105 * on this channel.
106 * @IEEE80211_CHAN_4MHZ: 4 MHz bandwidth is permitted
107 * on this channel.
108 * @IEEE80211_CHAN_8MHZ: 8 MHz bandwidth is permitted
109 * on this channel.
110 * @IEEE80211_CHAN_16MHZ: 16 MHz bandwidth is permitted
111 * on this channel.
112 *
113 */
114enum ieee80211_channel_flags {
115 IEEE80211_CHAN_DISABLED = 1<<0,
116 IEEE80211_CHAN_NO_IR = 1<<1,
117 /* hole at 1<<2 */
118 IEEE80211_CHAN_RADAR = 1<<3,
119 IEEE80211_CHAN_NO_HT40PLUS = 1<<4,
120 IEEE80211_CHAN_NO_HT40MINUS = 1<<5,
121 IEEE80211_CHAN_NO_OFDM = 1<<6,
122 IEEE80211_CHAN_NO_80MHZ = 1<<7,
123 IEEE80211_CHAN_NO_160MHZ = 1<<8,
124 IEEE80211_CHAN_INDOOR_ONLY = 1<<9,
125 IEEE80211_CHAN_IR_CONCURRENT = 1<<10,
126 IEEE80211_CHAN_NO_20MHZ = 1<<11,
127 IEEE80211_CHAN_NO_10MHZ = 1<<12,
128 IEEE80211_CHAN_NO_HE = 1<<13,
129 IEEE80211_CHAN_1MHZ = 1<<14,
130 IEEE80211_CHAN_2MHZ = 1<<15,
131 IEEE80211_CHAN_4MHZ = 1<<16,
132 IEEE80211_CHAN_8MHZ = 1<<17,
133 IEEE80211_CHAN_16MHZ = 1<<18,
134};
135
136#define IEEE80211_CHAN_NO_HT40 \
137 (IEEE80211_CHAN_NO_HT40PLUS | IEEE80211_CHAN_NO_HT40MINUS)
138
139#define IEEE80211_DFS_MIN_CAC_TIME_MS 60000
140#define IEEE80211_DFS_MIN_NOP_TIME_MS (30 * 60 * 1000)
141
142/**
143 * struct ieee80211_channel - channel definition
144 *
145 * This structure describes a single channel for use
146 * with cfg80211.
147 *
148 * @center_freq: center frequency in MHz
149 * @freq_offset: offset from @center_freq, in KHz
150 * @hw_value: hardware-specific value for the channel
151 * @flags: channel flags from &enum ieee80211_channel_flags.
152 * @orig_flags: channel flags at registration time, used by regulatory
153 * code to support devices with additional restrictions
154 * @band: band this channel belongs to.
155 * @max_antenna_gain: maximum antenna gain in dBi
156 * @max_power: maximum transmission power (in dBm)
157 * @max_reg_power: maximum regulatory transmission power (in dBm)
158 * @beacon_found: helper to regulatory code to indicate when a beacon
159 * has been found on this channel. Use regulatory_hint_found_beacon()
160 * to enable this, this is useful only on 5 GHz band.
161 * @orig_mag: internal use
162 * @orig_mpwr: internal use
163 * @dfs_state: current state of this channel. Only relevant if radar is required
164 * on this channel.
165 * @dfs_state_entered: timestamp (jiffies) when the dfs state was entered.
166 * @dfs_cac_ms: DFS CAC time in milliseconds, this is valid for DFS channels.
167 */
168struct ieee80211_channel {
169 enum nl80211_band band;
170 u32 center_freq;
171 u16 freq_offset;
172 u16 hw_value;
173 u32 flags;
174 int max_antenna_gain;
175 int max_power;
176 int max_reg_power;
177 bool beacon_found;
178 u32 orig_flags;
179 int orig_mag, orig_mpwr;
180 enum nl80211_dfs_state dfs_state;
181 unsigned long dfs_state_entered;
182 unsigned int dfs_cac_ms;
183};
184
185/**
186 * enum ieee80211_rate_flags - rate flags
187 *
188 * Hardware/specification flags for rates. These are structured
189 * in a way that allows using the same bitrate structure for
190 * different bands/PHY modes.
191 *
192 * @IEEE80211_RATE_SHORT_PREAMBLE: Hardware can send with short
193 * preamble on this bitrate; only relevant in 2.4GHz band and
194 * with CCK rates.
195 * @IEEE80211_RATE_MANDATORY_A: This bitrate is a mandatory rate
196 * when used with 802.11a (on the 5 GHz band); filled by the
197 * core code when registering the wiphy.
198 * @IEEE80211_RATE_MANDATORY_B: This bitrate is a mandatory rate
199 * when used with 802.11b (on the 2.4 GHz band); filled by the
200 * core code when registering the wiphy.
201 * @IEEE80211_RATE_MANDATORY_G: This bitrate is a mandatory rate
202 * when used with 802.11g (on the 2.4 GHz band); filled by the
203 * core code when registering the wiphy.
204 * @IEEE80211_RATE_ERP_G: This is an ERP rate in 802.11g mode.
205 * @IEEE80211_RATE_SUPPORTS_5MHZ: Rate can be used in 5 MHz mode
206 * @IEEE80211_RATE_SUPPORTS_10MHZ: Rate can be used in 10 MHz mode
207 */
208enum ieee80211_rate_flags {
209 IEEE80211_RATE_SHORT_PREAMBLE = 1<<0,
210 IEEE80211_RATE_MANDATORY_A = 1<<1,
211 IEEE80211_RATE_MANDATORY_B = 1<<2,
212 IEEE80211_RATE_MANDATORY_G = 1<<3,
213 IEEE80211_RATE_ERP_G = 1<<4,
214 IEEE80211_RATE_SUPPORTS_5MHZ = 1<<5,
215 IEEE80211_RATE_SUPPORTS_10MHZ = 1<<6,
216};
217
218/**
219 * enum ieee80211_bss_type - BSS type filter
220 *
221 * @IEEE80211_BSS_TYPE_ESS: Infrastructure BSS
222 * @IEEE80211_BSS_TYPE_PBSS: Personal BSS
223 * @IEEE80211_BSS_TYPE_IBSS: Independent BSS
224 * @IEEE80211_BSS_TYPE_MBSS: Mesh BSS
225 * @IEEE80211_BSS_TYPE_ANY: Wildcard value for matching any BSS type
226 */
227enum ieee80211_bss_type {
228 IEEE80211_BSS_TYPE_ESS,
229 IEEE80211_BSS_TYPE_PBSS,
230 IEEE80211_BSS_TYPE_IBSS,
231 IEEE80211_BSS_TYPE_MBSS,
232 IEEE80211_BSS_TYPE_ANY
233};
234
235/**
236 * enum ieee80211_privacy - BSS privacy filter
237 *
238 * @IEEE80211_PRIVACY_ON: privacy bit set
239 * @IEEE80211_PRIVACY_OFF: privacy bit clear
240 * @IEEE80211_PRIVACY_ANY: Wildcard value for matching any privacy setting
241 */
242enum ieee80211_privacy {
243 IEEE80211_PRIVACY_ON,
244 IEEE80211_PRIVACY_OFF,
245 IEEE80211_PRIVACY_ANY
246};
247
248#define IEEE80211_PRIVACY(x) \
249 ((x) ? IEEE80211_PRIVACY_ON : IEEE80211_PRIVACY_OFF)
250
251/**
252 * struct ieee80211_rate - bitrate definition
253 *
254 * This structure describes a bitrate that an 802.11 PHY can
255 * operate with. The two values @hw_value and @hw_value_short
256 * are only for driver use when pointers to this structure are
257 * passed around.
258 *
259 * @flags: rate-specific flags
260 * @bitrate: bitrate in units of 100 Kbps
261 * @hw_value: driver/hardware value for this rate
262 * @hw_value_short: driver/hardware value for this rate when
263 * short preamble is used
264 */
265struct ieee80211_rate {
266 u32 flags;
267 u16 bitrate;
268 u16 hw_value, hw_value_short;
269};
270
271/**
272 * struct ieee80211_he_obss_pd - AP settings for spatial reuse
273 *
274 * @enable: is the feature enabled.
275 * @sr_ctrl: The SR Control field of SRP element.
276 * @non_srg_max_offset: non-SRG maximum tx power offset
277 * @min_offset: minimal tx power offset an associated station shall use
278 * @max_offset: maximum tx power offset an associated station shall use
279 * @bss_color_bitmap: bitmap that indicates the BSS color values used by
280 * members of the SRG
281 * @partial_bssid_bitmap: bitmap that indicates the partial BSSID values
282 * used by members of the SRG
283 */
284struct ieee80211_he_obss_pd {
285 bool enable;
286 u8 sr_ctrl;
287 u8 non_srg_max_offset;
288 u8 min_offset;
289 u8 max_offset;
290 u8 bss_color_bitmap[8];
291 u8 partial_bssid_bitmap[8];
292};
293
294/**
295 * struct cfg80211_he_bss_color - AP settings for BSS coloring
296 *
297 * @color: the current color.
298 * @enabled: HE BSS color is used
299 * @partial: define the AID equation.
300 */
301struct cfg80211_he_bss_color {
302 u8 color;
303 bool enabled;
304 bool partial;
305};
306
307/**
308 * struct ieee80211_sta_ht_cap - STA's HT capabilities
309 *
310 * This structure describes most essential parameters needed
311 * to describe 802.11n HT capabilities for an STA.
312 *
313 * @ht_supported: is HT supported by the STA
314 * @cap: HT capabilities map as described in 802.11n spec
315 * @ampdu_factor: Maximum A-MPDU length factor
316 * @ampdu_density: Minimum A-MPDU spacing
317 * @mcs: Supported MCS rates
318 */
319struct ieee80211_sta_ht_cap {
320 u16 cap; /* use IEEE80211_HT_CAP_ */
321 bool ht_supported;
322 u8 ampdu_factor;
323 u8 ampdu_density;
324 struct ieee80211_mcs_info mcs;
325};
326
327/**
328 * struct ieee80211_sta_vht_cap - STA's VHT capabilities
329 *
330 * This structure describes most essential parameters needed
331 * to describe 802.11ac VHT capabilities for an STA.
332 *
333 * @vht_supported: is VHT supported by the STA
334 * @cap: VHT capabilities map as described in 802.11ac spec
335 * @vht_mcs: Supported VHT MCS rates
336 */
337struct ieee80211_sta_vht_cap {
338 bool vht_supported;
339 u32 cap; /* use IEEE80211_VHT_CAP_ */
340 struct ieee80211_vht_mcs_info vht_mcs;
341};
342
343#define IEEE80211_HE_PPE_THRES_MAX_LEN 25
344
345/**
346 * struct ieee80211_sta_he_cap - STA's HE capabilities
347 *
348 * This structure describes most essential parameters needed
349 * to describe 802.11ax HE capabilities for a STA.
350 *
351 * @has_he: true iff HE data is valid.
352 * @he_cap_elem: Fixed portion of the HE capabilities element.
353 * @he_mcs_nss_supp: The supported NSS/MCS combinations.
354 * @ppe_thres: Holds the PPE Thresholds data.
355 */
356struct ieee80211_sta_he_cap {
357 bool has_he;
358 struct ieee80211_he_cap_elem he_cap_elem;
359 struct ieee80211_he_mcs_nss_supp he_mcs_nss_supp;
360 u8 ppe_thres[IEEE80211_HE_PPE_THRES_MAX_LEN];
361};
362
363/**
364 * struct ieee80211_sband_iftype_data - sband data per interface type
365 *
366 * This structure encapsulates sband data that is relevant for the
367 * interface types defined in @types_mask. Each type in the
368 * @types_mask must be unique across all instances of iftype_data.
369 *
370 * @types_mask: interface types mask
371 * @he_cap: holds the HE capabilities
372 * @he_6ghz_capa: HE 6 GHz capabilities, must be filled in for a
373 * 6 GHz band channel (and 0 may be valid value).
374 * @vendor_elems: vendor element(s) to advertise
375 * @vendor_elems.data: vendor element(s) data
376 * @vendor_elems.len: vendor element(s) length
377 */
378struct ieee80211_sband_iftype_data {
379 u16 types_mask;
380 struct ieee80211_sta_he_cap he_cap;
381 struct ieee80211_he_6ghz_capa he_6ghz_capa;
382 struct {
383 const u8 *data;
384 unsigned int len;
385 } vendor_elems;
386};
387
388/**
389 * enum ieee80211_edmg_bw_config - allowed channel bandwidth configurations
390 *
391 * @IEEE80211_EDMG_BW_CONFIG_4: 2.16GHz
392 * @IEEE80211_EDMG_BW_CONFIG_5: 2.16GHz and 4.32GHz
393 * @IEEE80211_EDMG_BW_CONFIG_6: 2.16GHz, 4.32GHz and 6.48GHz
394 * @IEEE80211_EDMG_BW_CONFIG_7: 2.16GHz, 4.32GHz, 6.48GHz and 8.64GHz
395 * @IEEE80211_EDMG_BW_CONFIG_8: 2.16GHz and 2.16GHz + 2.16GHz
396 * @IEEE80211_EDMG_BW_CONFIG_9: 2.16GHz, 4.32GHz and 2.16GHz + 2.16GHz
397 * @IEEE80211_EDMG_BW_CONFIG_10: 2.16GHz, 4.32GHz, 6.48GHz and 2.16GHz+2.16GHz
398 * @IEEE80211_EDMG_BW_CONFIG_11: 2.16GHz, 4.32GHz, 6.48GHz, 8.64GHz and
399 * 2.16GHz+2.16GHz
400 * @IEEE80211_EDMG_BW_CONFIG_12: 2.16GHz, 2.16GHz + 2.16GHz and
401 * 4.32GHz + 4.32GHz
402 * @IEEE80211_EDMG_BW_CONFIG_13: 2.16GHz, 4.32GHz, 2.16GHz + 2.16GHz and
403 * 4.32GHz + 4.32GHz
404 * @IEEE80211_EDMG_BW_CONFIG_14: 2.16GHz, 4.32GHz, 6.48GHz, 2.16GHz + 2.16GHz
405 * and 4.32GHz + 4.32GHz
406 * @IEEE80211_EDMG_BW_CONFIG_15: 2.16GHz, 4.32GHz, 6.48GHz, 8.64GHz,
407 * 2.16GHz + 2.16GHz and 4.32GHz + 4.32GHz
408 */
409enum ieee80211_edmg_bw_config {
410 IEEE80211_EDMG_BW_CONFIG_4 = 4,
411 IEEE80211_EDMG_BW_CONFIG_5 = 5,
412 IEEE80211_EDMG_BW_CONFIG_6 = 6,
413 IEEE80211_EDMG_BW_CONFIG_7 = 7,
414 IEEE80211_EDMG_BW_CONFIG_8 = 8,
415 IEEE80211_EDMG_BW_CONFIG_9 = 9,
416 IEEE80211_EDMG_BW_CONFIG_10 = 10,
417 IEEE80211_EDMG_BW_CONFIG_11 = 11,
418 IEEE80211_EDMG_BW_CONFIG_12 = 12,
419 IEEE80211_EDMG_BW_CONFIG_13 = 13,
420 IEEE80211_EDMG_BW_CONFIG_14 = 14,
421 IEEE80211_EDMG_BW_CONFIG_15 = 15,
422};
423
424/**
425 * struct ieee80211_edmg - EDMG configuration
426 *
427 * This structure describes most essential parameters needed
428 * to describe 802.11ay EDMG configuration
429 *
430 * @channels: bitmap that indicates the 2.16 GHz channel(s)
431 * that are allowed to be used for transmissions.
432 * Bit 0 indicates channel 1, bit 1 indicates channel 2, etc.
433 * Set to 0 indicate EDMG not supported.
434 * @bw_config: Channel BW Configuration subfield encodes
435 * the allowed channel bandwidth configurations
436 */
437struct ieee80211_edmg {
438 u8 channels;
439 enum ieee80211_edmg_bw_config bw_config;
440};
441
442/**
443 * struct ieee80211_sta_s1g_cap - STA's S1G capabilities
444 *
445 * This structure describes most essential parameters needed
446 * to describe 802.11ah S1G capabilities for a STA.
447 *
448 * @s1g_supported: is STA an S1G STA
449 * @cap: S1G capabilities information
450 * @nss_mcs: Supported NSS MCS set
451 */
452struct ieee80211_sta_s1g_cap {
453 bool s1g;
454 u8 cap[10]; /* use S1G_CAPAB_ */
455 u8 nss_mcs[5];
456};
457
458/**
459 * struct ieee80211_supported_band - frequency band definition
460 *
461 * This structure describes a frequency band a wiphy
462 * is able to operate in.
463 *
464 * @channels: Array of channels the hardware can operate with
465 * in this band.
466 * @band: the band this structure represents
467 * @n_channels: Number of channels in @channels
468 * @bitrates: Array of bitrates the hardware can operate with
469 * in this band. Must be sorted to give a valid "supported
470 * rates" IE, i.e. CCK rates first, then OFDM.
471 * @n_bitrates: Number of bitrates in @bitrates
472 * @ht_cap: HT capabilities in this band
473 * @vht_cap: VHT capabilities in this band
474 * @s1g_cap: S1G capabilities in this band
475 * @edmg_cap: EDMG capabilities in this band
476 * @s1g_cap: S1G capabilities in this band (S1B band only, of course)
477 * @n_iftype_data: number of iftype data entries
478 * @iftype_data: interface type data entries. Note that the bits in
479 * @types_mask inside this structure cannot overlap (i.e. only
480 * one occurrence of each type is allowed across all instances of
481 * iftype_data).
482 */
483struct ieee80211_supported_band {
484 struct ieee80211_channel *channels;
485 struct ieee80211_rate *bitrates;
486 enum nl80211_band band;
487 int n_channels;
488 int n_bitrates;
489 struct ieee80211_sta_ht_cap ht_cap;
490 struct ieee80211_sta_vht_cap vht_cap;
491 struct ieee80211_sta_s1g_cap s1g_cap;
492 struct ieee80211_edmg edmg_cap;
493 u16 n_iftype_data;
494 const struct ieee80211_sband_iftype_data *iftype_data;
495};
496
497/**
498 * ieee80211_get_sband_iftype_data - return sband data for a given iftype
499 * @sband: the sband to search for the STA on
500 * @iftype: enum nl80211_iftype
501 *
502 * Return: pointer to struct ieee80211_sband_iftype_data, or NULL is none found
503 */
504static inline const struct ieee80211_sband_iftype_data *
505ieee80211_get_sband_iftype_data(const struct ieee80211_supported_band *sband,
506 u8 iftype)
507{
508 int i;
509
510 if (WARN_ON(iftype >= NL80211_IFTYPE_MAX))
511 return NULL;
512
513 for (i = 0; i < sband->n_iftype_data; i++) {
514 const struct ieee80211_sband_iftype_data *data =
515 &sband->iftype_data[i];
516
517 if (data->types_mask & BIT(iftype))
518 return data;
519 }
520
521 return NULL;
522}
523
524/**
525 * ieee80211_get_he_iftype_cap - return HE capabilities for an sband's iftype
526 * @sband: the sband to search for the iftype on
527 * @iftype: enum nl80211_iftype
528 *
529 * Return: pointer to the struct ieee80211_sta_he_cap, or NULL is none found
530 */
531static inline const struct ieee80211_sta_he_cap *
532ieee80211_get_he_iftype_cap(const struct ieee80211_supported_band *sband,
533 u8 iftype)
534{
535 const struct ieee80211_sband_iftype_data *data =
536 ieee80211_get_sband_iftype_data(sband, iftype);
537
538 if (data && data->he_cap.has_he)
539 return &data->he_cap;
540
541 return NULL;
542}
543
544/**
545 * ieee80211_get_he_6ghz_capa - return HE 6 GHz capabilities
546 * @sband: the sband to search for the STA on
547 * @iftype: the iftype to search for
548 *
549 * Return: the 6GHz capabilities
550 */
551static inline __le16
552ieee80211_get_he_6ghz_capa(const struct ieee80211_supported_band *sband,
553 enum nl80211_iftype iftype)
554{
555 const struct ieee80211_sband_iftype_data *data =
556 ieee80211_get_sband_iftype_data(sband, iftype);
557
558 if (WARN_ON(!data || !data->he_cap.has_he))
559 return 0;
560
561 return data->he_6ghz_capa.capa;
562}
563
564/**
565 * wiphy_read_of_freq_limits - read frequency limits from device tree
566 *
567 * @wiphy: the wireless device to get extra limits for
568 *
569 * Some devices may have extra limitations specified in DT. This may be useful
570 * for chipsets that normally support more bands but are limited due to board
571 * design (e.g. by antennas or external power amplifier).
572 *
573 * This function reads info from DT and uses it to *modify* channels (disable
574 * unavailable ones). It's usually a *bad* idea to use it in drivers with
575 * shared channel data as DT limitations are device specific. You should make
576 * sure to call it only if channels in wiphy are copied and can be modified
577 * without affecting other devices.
578 *
579 * As this function access device node it has to be called after set_wiphy_dev.
580 * It also modifies channels so they have to be set first.
581 * If using this helper, call it before wiphy_register().
582 */
583#ifdef CONFIG_OF
584void wiphy_read_of_freq_limits(struct wiphy *wiphy);
585#else /* CONFIG_OF */
586static inline void wiphy_read_of_freq_limits(struct wiphy *wiphy)
587{
588}
589#endif /* !CONFIG_OF */
590
591
592/*
593 * Wireless hardware/device configuration structures and methods
594 */
595
596/**
597 * DOC: Actions and configuration
598 *
599 * Each wireless device and each virtual interface offer a set of configuration
600 * operations and other actions that are invoked by userspace. Each of these
601 * actions is described in the operations structure, and the parameters these
602 * operations use are described separately.
603 *
604 * Additionally, some operations are asynchronous and expect to get status
605 * information via some functions that drivers need to call.
606 *
607 * Scanning and BSS list handling with its associated functionality is described
608 * in a separate chapter.
609 */
610
611#define VHT_MUMIMO_GROUPS_DATA_LEN (WLAN_MEMBERSHIP_LEN +\
612 WLAN_USER_POSITION_LEN)
613
614/**
615 * struct vif_params - describes virtual interface parameters
616 * @flags: monitor interface flags, unchanged if 0, otherwise
617 * %MONITOR_FLAG_CHANGED will be set
618 * @use_4addr: use 4-address frames
619 * @macaddr: address to use for this virtual interface.
620 * If this parameter is set to zero address the driver may
621 * determine the address as needed.
622 * This feature is only fully supported by drivers that enable the
623 * %NL80211_FEATURE_MAC_ON_CREATE flag. Others may support creating
624 ** only p2p devices with specified MAC.
625 * @vht_mumimo_groups: MU-MIMO groupID, used for monitoring MU-MIMO packets
626 * belonging to that MU-MIMO groupID; %NULL if not changed
627 * @vht_mumimo_follow_addr: MU-MIMO follow address, used for monitoring
628 * MU-MIMO packets going to the specified station; %NULL if not changed
629 */
630struct vif_params {
631 u32 flags;
632 int use_4addr;
633 u8 macaddr[ETH_ALEN];
634 const u8 *vht_mumimo_groups;
635 const u8 *vht_mumimo_follow_addr;
636};
637
638/**
639 * struct key_params - key information
640 *
641 * Information about a key
642 *
643 * @key: key material
644 * @key_len: length of key material
645 * @cipher: cipher suite selector
646 * @seq: sequence counter (IV/PN) for TKIP and CCMP keys, only used
647 * with the get_key() callback, must be in little endian,
648 * length given by @seq_len.
649 * @seq_len: length of @seq.
650 * @vlan_id: vlan_id for VLAN group key (if nonzero)
651 * @mode: key install mode (RX_TX, NO_TX or SET_TX)
652 */
653struct key_params {
654 const u8 *key;
655 const u8 *seq;
656 int key_len;
657 int seq_len;
658 u16 vlan_id;
659 u32 cipher;
660 enum nl80211_key_mode mode;
661};
662
663/**
664 * struct cfg80211_chan_def - channel definition
665 * @chan: the (control) channel
666 * @width: channel width
667 * @center_freq1: center frequency of first segment
668 * @center_freq2: center frequency of second segment
669 * (only with 80+80 MHz)
670 * @edmg: define the EDMG channels configuration.
671 * If edmg is requested (i.e. the .channels member is non-zero),
672 * chan will define the primary channel and all other
673 * parameters are ignored.
674 * @freq1_offset: offset from @center_freq1, in KHz
675 */
676struct cfg80211_chan_def {
677 struct ieee80211_channel *chan;
678 enum nl80211_chan_width width;
679 u32 center_freq1;
680 u32 center_freq2;
681 struct ieee80211_edmg edmg;
682 u16 freq1_offset;
683};
684
685/*
686 * cfg80211_bitrate_mask - masks for bitrate control
687 */
688struct cfg80211_bitrate_mask {
689 struct {
690 u32 legacy;
691 u8 ht_mcs[IEEE80211_HT_MCS_MASK_LEN];
692 u16 vht_mcs[NL80211_VHT_NSS_MAX];
693 u16 he_mcs[NL80211_HE_NSS_MAX];
694 enum nl80211_txrate_gi gi;
695 enum nl80211_he_gi he_gi;
696 enum nl80211_he_ltf he_ltf;
697 } control[NUM_NL80211_BANDS];
698};
699
700
701/**
702 * struct cfg80211_tid_cfg - TID specific configuration
703 * @config_override: Flag to notify driver to reset TID configuration
704 * of the peer.
705 * @tids: bitmap of TIDs to modify
706 * @mask: bitmap of attributes indicating which parameter changed,
707 * similar to &nl80211_tid_config_supp.
708 * @noack: noack configuration value for the TID
709 * @retry_long: retry count value
710 * @retry_short: retry count value
711 * @ampdu: Enable/Disable MPDU aggregation
712 * @rtscts: Enable/Disable RTS/CTS
713 * @amsdu: Enable/Disable MSDU aggregation
714 * @txrate_type: Tx bitrate mask type
715 * @txrate_mask: Tx bitrate to be applied for the TID
716 */
717struct cfg80211_tid_cfg {
718 bool config_override;
719 u8 tids;
720 u64 mask;
721 enum nl80211_tid_config noack;
722 u8 retry_long, retry_short;
723 enum nl80211_tid_config ampdu;
724 enum nl80211_tid_config rtscts;
725 enum nl80211_tid_config amsdu;
726 enum nl80211_tx_rate_setting txrate_type;
727 struct cfg80211_bitrate_mask txrate_mask;
728};
729
730/**
731 * struct cfg80211_tid_config - TID configuration
732 * @peer: Station's MAC address
733 * @n_tid_conf: Number of TID specific configurations to be applied
734 * @tid_conf: Configuration change info
735 */
736struct cfg80211_tid_config {
737 const u8 *peer;
738 u32 n_tid_conf;
739 struct cfg80211_tid_cfg tid_conf[];
740};
741
742/**
743 * cfg80211_get_chandef_type - return old channel type from chandef
744 * @chandef: the channel definition
745 *
746 * Return: The old channel type (NOHT, HT20, HT40+/-) from a given
747 * chandef, which must have a bandwidth allowing this conversion.
748 */
749static inline enum nl80211_channel_type
750cfg80211_get_chandef_type(const struct cfg80211_chan_def *chandef)
751{
752 switch (chandef->width) {
753 case NL80211_CHAN_WIDTH_20_NOHT:
754 return NL80211_CHAN_NO_HT;
755 case NL80211_CHAN_WIDTH_20:
756 return NL80211_CHAN_HT20;
757 case NL80211_CHAN_WIDTH_40:
758 if (chandef->center_freq1 > chandef->chan->center_freq)
759 return NL80211_CHAN_HT40PLUS;
760 return NL80211_CHAN_HT40MINUS;
761 default:
762 WARN_ON(1);
763 return NL80211_CHAN_NO_HT;
764 }
765}
766
767/**
768 * cfg80211_chandef_create - create channel definition using channel type
769 * @chandef: the channel definition struct to fill
770 * @channel: the control channel
771 * @chantype: the channel type
772 *
773 * Given a channel type, create a channel definition.
774 */
775void cfg80211_chandef_create(struct cfg80211_chan_def *chandef,
776 struct ieee80211_channel *channel,
777 enum nl80211_channel_type chantype);
778
779/**
780 * cfg80211_chandef_identical - check if two channel definitions are identical
781 * @chandef1: first channel definition
782 * @chandef2: second channel definition
783 *
784 * Return: %true if the channels defined by the channel definitions are
785 * identical, %false otherwise.
786 */
787static inline bool
788cfg80211_chandef_identical(const struct cfg80211_chan_def *chandef1,
789 const struct cfg80211_chan_def *chandef2)
790{
791 return (chandef1->chan == chandef2->chan &&
792 chandef1->width == chandef2->width &&
793 chandef1->center_freq1 == chandef2->center_freq1 &&
794 chandef1->freq1_offset == chandef2->freq1_offset &&
795 chandef1->center_freq2 == chandef2->center_freq2);
796}
797
798/**
799 * cfg80211_chandef_is_edmg - check if chandef represents an EDMG channel
800 *
801 * @chandef: the channel definition
802 *
803 * Return: %true if EDMG defined, %false otherwise.
804 */
805static inline bool
806cfg80211_chandef_is_edmg(const struct cfg80211_chan_def *chandef)
807{
808 return chandef->edmg.channels || chandef->edmg.bw_config;
809}
810
811/**
812 * cfg80211_chandef_compatible - check if two channel definitions are compatible
813 * @chandef1: first channel definition
814 * @chandef2: second channel definition
815 *
816 * Return: %NULL if the given channel definitions are incompatible,
817 * chandef1 or chandef2 otherwise.
818 */
819const struct cfg80211_chan_def *
820cfg80211_chandef_compatible(const struct cfg80211_chan_def *chandef1,
821 const struct cfg80211_chan_def *chandef2);
822
823/**
824 * cfg80211_chandef_valid - check if a channel definition is valid
825 * @chandef: the channel definition to check
826 * Return: %true if the channel definition is valid. %false otherwise.
827 */
828bool cfg80211_chandef_valid(const struct cfg80211_chan_def *chandef);
829
830/**
831 * cfg80211_chandef_usable - check if secondary channels can be used
832 * @wiphy: the wiphy to validate against
833 * @chandef: the channel definition to check
834 * @prohibited_flags: the regulatory channel flags that must not be set
835 * Return: %true if secondary channels are usable. %false otherwise.
836 */
837bool cfg80211_chandef_usable(struct wiphy *wiphy,
838 const struct cfg80211_chan_def *chandef,
839 u32 prohibited_flags);
840
841/**
842 * cfg80211_chandef_dfs_required - checks if radar detection is required
843 * @wiphy: the wiphy to validate against
844 * @chandef: the channel definition to check
845 * @iftype: the interface type as specified in &enum nl80211_iftype
846 * Returns:
847 * 1 if radar detection is required, 0 if it is not, < 0 on error
848 */
849int cfg80211_chandef_dfs_required(struct wiphy *wiphy,
850 const struct cfg80211_chan_def *chandef,
851 enum nl80211_iftype iftype);
852
853/**
854 * ieee80211_chandef_rate_flags - returns rate flags for a channel
855 *
856 * In some channel types, not all rates may be used - for example CCK
857 * rates may not be used in 5/10 MHz channels.
858 *
859 * @chandef: channel definition for the channel
860 *
861 * Returns: rate flags which apply for this channel
862 */
863static inline enum ieee80211_rate_flags
864ieee80211_chandef_rate_flags(struct cfg80211_chan_def *chandef)
865{
866 switch (chandef->width) {
867 case NL80211_CHAN_WIDTH_5:
868 return IEEE80211_RATE_SUPPORTS_5MHZ;
869 case NL80211_CHAN_WIDTH_10:
870 return IEEE80211_RATE_SUPPORTS_10MHZ;
871 default:
872 break;
873 }
874 return 0;
875}
876
877/**
878 * ieee80211_chandef_max_power - maximum transmission power for the chandef
879 *
880 * In some regulations, the transmit power may depend on the configured channel
881 * bandwidth which may be defined as dBm/MHz. This function returns the actual
882 * max_power for non-standard (20 MHz) channels.
883 *
884 * @chandef: channel definition for the channel
885 *
886 * Returns: maximum allowed transmission power in dBm for the chandef
887 */
888static inline int
889ieee80211_chandef_max_power(struct cfg80211_chan_def *chandef)
890{
891 switch (chandef->width) {
892 case NL80211_CHAN_WIDTH_5:
893 return min(chandef->chan->max_reg_power - 6,
894 chandef->chan->max_power);
895 case NL80211_CHAN_WIDTH_10:
896 return min(chandef->chan->max_reg_power - 3,
897 chandef->chan->max_power);
898 default:
899 break;
900 }
901 return chandef->chan->max_power;
902}
903
904/**
905 * cfg80211_any_usable_channels - check for usable channels
906 * @wiphy: the wiphy to check for
907 * @band_mask: which bands to check on
908 * @prohibited_flags: which channels to not consider usable,
909 * %IEEE80211_CHAN_DISABLED is always taken into account
910 */
911bool cfg80211_any_usable_channels(struct wiphy *wiphy,
912 unsigned long band_mask,
913 u32 prohibited_flags);
914
915/**
916 * enum survey_info_flags - survey information flags
917 *
918 * @SURVEY_INFO_NOISE_DBM: noise (in dBm) was filled in
919 * @SURVEY_INFO_IN_USE: channel is currently being used
920 * @SURVEY_INFO_TIME: active time (in ms) was filled in
921 * @SURVEY_INFO_TIME_BUSY: busy time was filled in
922 * @SURVEY_INFO_TIME_EXT_BUSY: extension channel busy time was filled in
923 * @SURVEY_INFO_TIME_RX: receive time was filled in
924 * @SURVEY_INFO_TIME_TX: transmit time was filled in
925 * @SURVEY_INFO_TIME_SCAN: scan time was filled in
926 * @SURVEY_INFO_TIME_BSS_RX: local BSS receive time was filled in
927 *
928 * Used by the driver to indicate which info in &struct survey_info
929 * it has filled in during the get_survey().
930 */
931enum survey_info_flags {
932 SURVEY_INFO_NOISE_DBM = BIT(0),
933 SURVEY_INFO_IN_USE = BIT(1),
934 SURVEY_INFO_TIME = BIT(2),
935 SURVEY_INFO_TIME_BUSY = BIT(3),
936 SURVEY_INFO_TIME_EXT_BUSY = BIT(4),
937 SURVEY_INFO_TIME_RX = BIT(5),
938 SURVEY_INFO_TIME_TX = BIT(6),
939 SURVEY_INFO_TIME_SCAN = BIT(7),
940 SURVEY_INFO_TIME_BSS_RX = BIT(8),
941};
942
943/**
944 * struct survey_info - channel survey response
945 *
946 * @channel: the channel this survey record reports, may be %NULL for a single
947 * record to report global statistics
948 * @filled: bitflag of flags from &enum survey_info_flags
949 * @noise: channel noise in dBm. This and all following fields are
950 * optional
951 * @time: amount of time in ms the radio was turn on (on the channel)
952 * @time_busy: amount of time the primary channel was sensed busy
953 * @time_ext_busy: amount of time the extension channel was sensed busy
954 * @time_rx: amount of time the radio spent receiving data
955 * @time_tx: amount of time the radio spent transmitting data
956 * @time_scan: amount of time the radio spent for scanning
957 * @time_bss_rx: amount of time the radio spent receiving data on a local BSS
958 *
959 * Used by dump_survey() to report back per-channel survey information.
960 *
961 * This structure can later be expanded with things like
962 * channel duty cycle etc.
963 */
964struct survey_info {
965 struct ieee80211_channel *channel;
966 u64 time;
967 u64 time_busy;
968 u64 time_ext_busy;
969 u64 time_rx;
970 u64 time_tx;
971 u64 time_scan;
972 u64 time_bss_rx;
973 u32 filled;
974 s8 noise;
975};
976
977#define CFG80211_MAX_WEP_KEYS 4
978
979/**
980 * struct cfg80211_crypto_settings - Crypto settings
981 * @wpa_versions: indicates which, if any, WPA versions are enabled
982 * (from enum nl80211_wpa_versions)
983 * @cipher_group: group key cipher suite (or 0 if unset)
984 * @n_ciphers_pairwise: number of AP supported unicast ciphers
985 * @ciphers_pairwise: unicast key cipher suites
986 * @n_akm_suites: number of AKM suites
987 * @akm_suites: AKM suites
988 * @control_port: Whether user space controls IEEE 802.1X port, i.e.,
989 * sets/clears %NL80211_STA_FLAG_AUTHORIZED. If true, the driver is
990 * required to assume that the port is unauthorized until authorized by
991 * user space. Otherwise, port is marked authorized by default.
992 * @control_port_ethertype: the control port protocol that should be
993 * allowed through even on unauthorized ports
994 * @control_port_no_encrypt: TRUE to prevent encryption of control port
995 * protocol frames.
996 * @control_port_over_nl80211: TRUE if userspace expects to exchange control
997 * port frames over NL80211 instead of the network interface.
998 * @control_port_no_preauth: disables pre-auth rx over the nl80211 control
999 * port for mac80211
1000 * @wep_keys: static WEP keys, if not NULL points to an array of
1001 * CFG80211_MAX_WEP_KEYS WEP keys
1002 * @wep_tx_key: key index (0..3) of the default TX static WEP key
1003 * @psk: PSK (for devices supporting 4-way-handshake offload)
1004 * @sae_pwd: password for SAE authentication (for devices supporting SAE
1005 * offload)
1006 * @sae_pwd_len: length of SAE password (for devices supporting SAE offload)
1007 * @sae_pwe: The mechanisms allowed for SAE PWE derivation:
1008 *
1009 * NL80211_SAE_PWE_UNSPECIFIED
1010 * Not-specified, used to indicate userspace did not specify any
1011 * preference. The driver should follow its internal policy in
1012 * such a scenario.
1013 *
1014 * NL80211_SAE_PWE_HUNT_AND_PECK
1015 * Allow hunting-and-pecking loop only
1016 *
1017 * NL80211_SAE_PWE_HASH_TO_ELEMENT
1018 * Allow hash-to-element only
1019 *
1020 * NL80211_SAE_PWE_BOTH
1021 * Allow either hunting-and-pecking loop or hash-to-element
1022 */
1023struct cfg80211_crypto_settings {
1024 u32 wpa_versions;
1025 u32 cipher_group;
1026 int n_ciphers_pairwise;
1027 u32 ciphers_pairwise[NL80211_MAX_NR_CIPHER_SUITES];
1028 int n_akm_suites;
1029 u32 akm_suites[NL80211_MAX_NR_AKM_SUITES];
1030 bool control_port;
1031 __be16 control_port_ethertype;
1032 bool control_port_no_encrypt;
1033 bool control_port_over_nl80211;
1034 bool control_port_no_preauth;
1035 struct key_params *wep_keys;
1036 int wep_tx_key;
1037 const u8 *psk;
1038 const u8 *sae_pwd;
1039 u8 sae_pwd_len;
1040 enum nl80211_sae_pwe_mechanism sae_pwe;
1041};
1042
1043/**
1044 * struct cfg80211_beacon_data - beacon data
1045 * @head: head portion of beacon (before TIM IE)
1046 * or %NULL if not changed
1047 * @tail: tail portion of beacon (after TIM IE)
1048 * or %NULL if not changed
1049 * @head_len: length of @head
1050 * @tail_len: length of @tail
1051 * @beacon_ies: extra information element(s) to add into Beacon frames or %NULL
1052 * @beacon_ies_len: length of beacon_ies in octets
1053 * @proberesp_ies: extra information element(s) to add into Probe Response
1054 * frames or %NULL
1055 * @proberesp_ies_len: length of proberesp_ies in octets
1056 * @assocresp_ies: extra information element(s) to add into (Re)Association
1057 * Response frames or %NULL
1058 * @assocresp_ies_len: length of assocresp_ies in octets
1059 * @probe_resp_len: length of probe response template (@probe_resp)
1060 * @probe_resp: probe response template (AP mode only)
1061 * @ftm_responder: enable FTM responder functionality; -1 for no change
1062 * (which also implies no change in LCI/civic location data)
1063 * @lci: Measurement Report element content, starting with Measurement Token
1064 * (measurement type 8)
1065 * @civicloc: Measurement Report element content, starting with Measurement
1066 * Token (measurement type 11)
1067 * @lci_len: LCI data length
1068 * @civicloc_len: Civic location data length
1069 */
1070struct cfg80211_beacon_data {
1071 const u8 *head, *tail;
1072 const u8 *beacon_ies;
1073 const u8 *proberesp_ies;
1074 const u8 *assocresp_ies;
1075 const u8 *probe_resp;
1076 const u8 *lci;
1077 const u8 *civicloc;
1078 s8 ftm_responder;
1079
1080 size_t head_len, tail_len;
1081 size_t beacon_ies_len;
1082 size_t proberesp_ies_len;
1083 size_t assocresp_ies_len;
1084 size_t probe_resp_len;
1085 size_t lci_len;
1086 size_t civicloc_len;
1087};
1088
1089struct mac_address {
1090 u8 addr[ETH_ALEN];
1091};
1092
1093/**
1094 * struct cfg80211_acl_data - Access control list data
1095 *
1096 * @acl_policy: ACL policy to be applied on the station's
1097 * entry specified by mac_addr
1098 * @n_acl_entries: Number of MAC address entries passed
1099 * @mac_addrs: List of MAC addresses of stations to be used for ACL
1100 */
1101struct cfg80211_acl_data {
1102 enum nl80211_acl_policy acl_policy;
1103 int n_acl_entries;
1104
1105 /* Keep it last */
1106 struct mac_address mac_addrs[];
1107};
1108
1109/**
1110 * struct cfg80211_fils_discovery - FILS discovery parameters from
1111 * IEEE Std 802.11ai-2016, Annex C.3 MIB detail.
1112 *
1113 * @min_interval: Minimum packet interval in TUs (0 - 10000)
1114 * @max_interval: Maximum packet interval in TUs (0 - 10000)
1115 * @tmpl_len: Template length
1116 * @tmpl: Template data for FILS discovery frame including the action
1117 * frame headers.
1118 */
1119struct cfg80211_fils_discovery {
1120 u32 min_interval;
1121 u32 max_interval;
1122 size_t tmpl_len;
1123 const u8 *tmpl;
1124};
1125
1126/**
1127 * struct cfg80211_unsol_bcast_probe_resp - Unsolicited broadcast probe
1128 * response parameters in 6GHz.
1129 *
1130 * @interval: Packet interval in TUs. Maximum allowed is 20 TU, as mentioned
1131 * in IEEE P802.11ax/D6.0 26.17.2.3.2 - AP behavior for fast passive
1132 * scanning
1133 * @tmpl_len: Template length
1134 * @tmpl: Template data for probe response
1135 */
1136struct cfg80211_unsol_bcast_probe_resp {
1137 u32 interval;
1138 size_t tmpl_len;
1139 const u8 *tmpl;
1140};
1141
1142/**
1143 * enum cfg80211_ap_settings_flags - AP settings flags
1144 *
1145 * Used by cfg80211_ap_settings
1146 *
1147 * @AP_SETTINGS_EXTERNAL_AUTH_SUPPORT: AP supports external authentication
1148 */
1149enum cfg80211_ap_settings_flags {
1150 AP_SETTINGS_EXTERNAL_AUTH_SUPPORT = BIT(0),
1151};
1152
1153/**
1154 * struct cfg80211_ap_settings - AP configuration
1155 *
1156 * Used to configure an AP interface.
1157 *
1158 * @chandef: defines the channel to use
1159 * @beacon: beacon data
1160 * @beacon_interval: beacon interval
1161 * @dtim_period: DTIM period
1162 * @ssid: SSID to be used in the BSS (note: may be %NULL if not provided from
1163 * user space)
1164 * @ssid_len: length of @ssid
1165 * @hidden_ssid: whether to hide the SSID in Beacon/Probe Response frames
1166 * @crypto: crypto settings
1167 * @privacy: the BSS uses privacy
1168 * @auth_type: Authentication type (algorithm)
1169 * @smps_mode: SMPS mode
1170 * @inactivity_timeout: time in seconds to determine station's inactivity.
1171 * @p2p_ctwindow: P2P CT Window
1172 * @p2p_opp_ps: P2P opportunistic PS
1173 * @acl: ACL configuration used by the drivers which has support for
1174 * MAC address based access control
1175 * @pbss: If set, start as a PCP instead of AP. Relevant for DMG
1176 * networks.
1177 * @beacon_rate: bitrate to be used for beacons
1178 * @ht_cap: HT capabilities (or %NULL if HT isn't enabled)
1179 * @vht_cap: VHT capabilities (or %NULL if VHT isn't enabled)
1180 * @he_cap: HE capabilities (or %NULL if HE isn't enabled)
1181 * @ht_required: stations must support HT
1182 * @vht_required: stations must support VHT
1183 * @twt_responder: Enable Target Wait Time
1184 * @he_required: stations must support HE
1185 * @sae_h2e_required: stations must support direct H2E technique in SAE
1186 * @flags: flags, as defined in enum cfg80211_ap_settings_flags
1187 * @he_obss_pd: OBSS Packet Detection settings
1188 * @he_bss_color: BSS Color settings
1189 * @he_oper: HE operation IE (or %NULL if HE isn't enabled)
1190 * @fils_discovery: FILS discovery transmission parameters
1191 * @unsol_bcast_probe_resp: Unsolicited broadcast probe response parameters
1192 */
1193struct cfg80211_ap_settings {
1194 struct cfg80211_chan_def chandef;
1195
1196 struct cfg80211_beacon_data beacon;
1197
1198 int beacon_interval, dtim_period;
1199 const u8 *ssid;
1200 size_t ssid_len;
1201 enum nl80211_hidden_ssid hidden_ssid;
1202 struct cfg80211_crypto_settings crypto;
1203 bool privacy;
1204 enum nl80211_auth_type auth_type;
1205 enum nl80211_smps_mode smps_mode;
1206 int inactivity_timeout;
1207 u8 p2p_ctwindow;
1208 bool p2p_opp_ps;
1209 const struct cfg80211_acl_data *acl;
1210 bool pbss;
1211 struct cfg80211_bitrate_mask beacon_rate;
1212
1213 const struct ieee80211_ht_cap *ht_cap;
1214 const struct ieee80211_vht_cap *vht_cap;
1215 const struct ieee80211_he_cap_elem *he_cap;
1216 const struct ieee80211_he_operation *he_oper;
1217 bool ht_required, vht_required, he_required, sae_h2e_required;
1218 bool twt_responder;
1219 u32 flags;
1220 struct ieee80211_he_obss_pd he_obss_pd;
1221 struct cfg80211_he_bss_color he_bss_color;
1222 struct cfg80211_fils_discovery fils_discovery;
1223 struct cfg80211_unsol_bcast_probe_resp unsol_bcast_probe_resp;
1224};
1225
1226/**
1227 * struct cfg80211_csa_settings - channel switch settings
1228 *
1229 * Used for channel switch
1230 *
1231 * @chandef: defines the channel to use after the switch
1232 * @beacon_csa: beacon data while performing the switch
1233 * @counter_offsets_beacon: offsets of the counters within the beacon (tail)
1234 * @counter_offsets_presp: offsets of the counters within the probe response
1235 * @n_counter_offsets_beacon: number of csa counters the beacon (tail)
1236 * @n_counter_offsets_presp: number of csa counters in the probe response
1237 * @beacon_after: beacon data to be used on the new channel
1238 * @radar_required: whether radar detection is required on the new channel
1239 * @block_tx: whether transmissions should be blocked while changing
1240 * @count: number of beacons until switch
1241 */
1242struct cfg80211_csa_settings {
1243 struct cfg80211_chan_def chandef;
1244 struct cfg80211_beacon_data beacon_csa;
1245 const u16 *counter_offsets_beacon;
1246 const u16 *counter_offsets_presp;
1247 unsigned int n_counter_offsets_beacon;
1248 unsigned int n_counter_offsets_presp;
1249 struct cfg80211_beacon_data beacon_after;
1250 bool radar_required;
1251 bool block_tx;
1252 u8 count;
1253};
1254
1255/**
1256 * struct iface_combination_params - input parameters for interface combinations
1257 *
1258 * Used to pass interface combination parameters
1259 *
1260 * @num_different_channels: the number of different channels we want
1261 * to use for verification
1262 * @radar_detect: a bitmap where each bit corresponds to a channel
1263 * width where radar detection is needed, as in the definition of
1264 * &struct ieee80211_iface_combination.@radar_detect_widths
1265 * @iftype_num: array with the number of interfaces of each interface
1266 * type. The index is the interface type as specified in &enum
1267 * nl80211_iftype.
1268 * @new_beacon_int: set this to the beacon interval of a new interface
1269 * that's not operating yet, if such is to be checked as part of
1270 * the verification
1271 */
1272struct iface_combination_params {
1273 int num_different_channels;
1274 u8 radar_detect;
1275 int iftype_num[NUM_NL80211_IFTYPES];
1276 u32 new_beacon_int;
1277};
1278
1279/**
1280 * enum station_parameters_apply_mask - station parameter values to apply
1281 * @STATION_PARAM_APPLY_UAPSD: apply new uAPSD parameters (uapsd_queues, max_sp)
1282 * @STATION_PARAM_APPLY_CAPABILITY: apply new capability
1283 * @STATION_PARAM_APPLY_PLINK_STATE: apply new plink state
1284 *
1285 * Not all station parameters have in-band "no change" signalling,
1286 * for those that don't these flags will are used.
1287 */
1288enum station_parameters_apply_mask {
1289 STATION_PARAM_APPLY_UAPSD = BIT(0),
1290 STATION_PARAM_APPLY_CAPABILITY = BIT(1),
1291 STATION_PARAM_APPLY_PLINK_STATE = BIT(2),
1292 STATION_PARAM_APPLY_STA_TXPOWER = BIT(3),
1293};
1294
1295/**
1296 * struct sta_txpwr - station txpower configuration
1297 *
1298 * Used to configure txpower for station.
1299 *
1300 * @power: tx power (in dBm) to be used for sending data traffic. If tx power
1301 * is not provided, the default per-interface tx power setting will be
1302 * overriding. Driver should be picking up the lowest tx power, either tx
1303 * power per-interface or per-station.
1304 * @type: In particular if TPC %type is NL80211_TX_POWER_LIMITED then tx power
1305 * will be less than or equal to specified from userspace, whereas if TPC
1306 * %type is NL80211_TX_POWER_AUTOMATIC then it indicates default tx power.
1307 * NL80211_TX_POWER_FIXED is not a valid configuration option for
1308 * per peer TPC.
1309 */
1310struct sta_txpwr {
1311 s16 power;
1312 enum nl80211_tx_power_setting type;
1313};
1314
1315/**
1316 * struct station_parameters - station parameters
1317 *
1318 * Used to change and create a new station.
1319 *
1320 * @vlan: vlan interface station should belong to
1321 * @supported_rates: supported rates in IEEE 802.11 format
1322 * (or NULL for no change)
1323 * @supported_rates_len: number of supported rates
1324 * @sta_flags_mask: station flags that changed
1325 * (bitmask of BIT(%NL80211_STA_FLAG_...))
1326 * @sta_flags_set: station flags values
1327 * (bitmask of BIT(%NL80211_STA_FLAG_...))
1328 * @listen_interval: listen interval or -1 for no change
1329 * @aid: AID or zero for no change
1330 * @vlan_id: VLAN ID for station (if nonzero)
1331 * @peer_aid: mesh peer AID or zero for no change
1332 * @plink_action: plink action to take
1333 * @plink_state: set the peer link state for a station
1334 * @ht_capa: HT capabilities of station
1335 * @vht_capa: VHT capabilities of station
1336 * @uapsd_queues: bitmap of queues configured for uapsd. same format
1337 * as the AC bitmap in the QoS info field
1338 * @max_sp: max Service Period. same format as the MAX_SP in the
1339 * QoS info field (but already shifted down)
1340 * @sta_modify_mask: bitmap indicating which parameters changed
1341 * (for those that don't have a natural "no change" value),
1342 * see &enum station_parameters_apply_mask
1343 * @local_pm: local link-specific mesh power save mode (no change when set
1344 * to unknown)
1345 * @capability: station capability
1346 * @ext_capab: extended capabilities of the station
1347 * @ext_capab_len: number of extended capabilities
1348 * @supported_channels: supported channels in IEEE 802.11 format
1349 * @supported_channels_len: number of supported channels
1350 * @supported_oper_classes: supported oper classes in IEEE 802.11 format
1351 * @supported_oper_classes_len: number of supported operating classes
1352 * @opmode_notif: operating mode field from Operating Mode Notification
1353 * @opmode_notif_used: information if operating mode field is used
1354 * @support_p2p_ps: information if station supports P2P PS mechanism
1355 * @he_capa: HE capabilities of station
1356 * @he_capa_len: the length of the HE capabilities
1357 * @airtime_weight: airtime scheduler weight for this station
1358 * @txpwr: transmit power for an associated station
1359 * @he_6ghz_capa: HE 6 GHz Band capabilities of station
1360 */
1361struct station_parameters {
1362 const u8 *supported_rates;
1363 struct net_device *vlan;
1364 u32 sta_flags_mask, sta_flags_set;
1365 u32 sta_modify_mask;
1366 int listen_interval;
1367 u16 aid;
1368 u16 vlan_id;
1369 u16 peer_aid;
1370 u8 supported_rates_len;
1371 u8 plink_action;
1372 u8 plink_state;
1373 const struct ieee80211_ht_cap *ht_capa;
1374 const struct ieee80211_vht_cap *vht_capa;
1375 u8 uapsd_queues;
1376 u8 max_sp;
1377 enum nl80211_mesh_power_mode local_pm;
1378 u16 capability;
1379 const u8 *ext_capab;
1380 u8 ext_capab_len;
1381 const u8 *supported_channels;
1382 u8 supported_channels_len;
1383 const u8 *supported_oper_classes;
1384 u8 supported_oper_classes_len;
1385 u8 opmode_notif;
1386 bool opmode_notif_used;
1387 int support_p2p_ps;
1388 const struct ieee80211_he_cap_elem *he_capa;
1389 u8 he_capa_len;
1390 u16 airtime_weight;
1391 struct sta_txpwr txpwr;
1392 const struct ieee80211_he_6ghz_capa *he_6ghz_capa;
1393};
1394
1395/**
1396 * struct station_del_parameters - station deletion parameters
1397 *
1398 * Used to delete a station entry (or all stations).
1399 *
1400 * @mac: MAC address of the station to remove or NULL to remove all stations
1401 * @subtype: Management frame subtype to use for indicating removal
1402 * (10 = Disassociation, 12 = Deauthentication)
1403 * @reason_code: Reason code for the Disassociation/Deauthentication frame
1404 */
1405struct station_del_parameters {
1406 const u8 *mac;
1407 u8 subtype;
1408 u16 reason_code;
1409};
1410
1411/**
1412 * enum cfg80211_station_type - the type of station being modified
1413 * @CFG80211_STA_AP_CLIENT: client of an AP interface
1414 * @CFG80211_STA_AP_CLIENT_UNASSOC: client of an AP interface that is still
1415 * unassociated (update properties for this type of client is permitted)
1416 * @CFG80211_STA_AP_MLME_CLIENT: client of an AP interface that has
1417 * the AP MLME in the device
1418 * @CFG80211_STA_AP_STA: AP station on managed interface
1419 * @CFG80211_STA_IBSS: IBSS station
1420 * @CFG80211_STA_TDLS_PEER_SETUP: TDLS peer on managed interface (dummy entry
1421 * while TDLS setup is in progress, it moves out of this state when
1422 * being marked authorized; use this only if TDLS with external setup is
1423 * supported/used)
1424 * @CFG80211_STA_TDLS_PEER_ACTIVE: TDLS peer on managed interface (active
1425 * entry that is operating, has been marked authorized by userspace)
1426 * @CFG80211_STA_MESH_PEER_KERNEL: peer on mesh interface (kernel managed)
1427 * @CFG80211_STA_MESH_PEER_USER: peer on mesh interface (user managed)
1428 */
1429enum cfg80211_station_type {
1430 CFG80211_STA_AP_CLIENT,
1431 CFG80211_STA_AP_CLIENT_UNASSOC,
1432 CFG80211_STA_AP_MLME_CLIENT,
1433 CFG80211_STA_AP_STA,
1434 CFG80211_STA_IBSS,
1435 CFG80211_STA_TDLS_PEER_SETUP,
1436 CFG80211_STA_TDLS_PEER_ACTIVE,
1437 CFG80211_STA_MESH_PEER_KERNEL,
1438 CFG80211_STA_MESH_PEER_USER,
1439};
1440
1441/**
1442 * cfg80211_check_station_change - validate parameter changes
1443 * @wiphy: the wiphy this operates on
1444 * @params: the new parameters for a station
1445 * @statype: the type of station being modified
1446 *
1447 * Utility function for the @change_station driver method. Call this function
1448 * with the appropriate station type looking up the station (and checking that
1449 * it exists). It will verify whether the station change is acceptable, and if
1450 * not will return an error code. Note that it may modify the parameters for
1451 * backward compatibility reasons, so don't use them before calling this.
1452 */
1453int cfg80211_check_station_change(struct wiphy *wiphy,
1454 struct station_parameters *params,
1455 enum cfg80211_station_type statype);
1456
1457/**
1458 * enum rate_info_flags - bitrate info flags
1459 *
1460 * Used by the driver to indicate the specific rate transmission
1461 * type for 802.11n transmissions.
1462 *
1463 * @RATE_INFO_FLAGS_MCS: mcs field filled with HT MCS
1464 * @RATE_INFO_FLAGS_VHT_MCS: mcs field filled with VHT MCS
1465 * @RATE_INFO_FLAGS_SHORT_GI: 400ns guard interval
1466 * @RATE_INFO_FLAGS_DMG: 60GHz MCS
1467 * @RATE_INFO_FLAGS_HE_MCS: HE MCS information
1468 * @RATE_INFO_FLAGS_EDMG: 60GHz MCS in EDMG mode
1469 * @RATE_INFO_FLAGS_EXTENDED_SC_DMG: 60GHz extended SC MCS
1470 */
1471enum rate_info_flags {
1472 RATE_INFO_FLAGS_MCS = BIT(0),
1473 RATE_INFO_FLAGS_VHT_MCS = BIT(1),
1474 RATE_INFO_FLAGS_SHORT_GI = BIT(2),
1475 RATE_INFO_FLAGS_DMG = BIT(3),
1476 RATE_INFO_FLAGS_HE_MCS = BIT(4),
1477 RATE_INFO_FLAGS_EDMG = BIT(5),
1478 RATE_INFO_FLAGS_EXTENDED_SC_DMG = BIT(6),
1479};
1480
1481/**
1482 * enum rate_info_bw - rate bandwidth information
1483 *
1484 * Used by the driver to indicate the rate bandwidth.
1485 *
1486 * @RATE_INFO_BW_5: 5 MHz bandwidth
1487 * @RATE_INFO_BW_10: 10 MHz bandwidth
1488 * @RATE_INFO_BW_20: 20 MHz bandwidth
1489 * @RATE_INFO_BW_40: 40 MHz bandwidth
1490 * @RATE_INFO_BW_80: 80 MHz bandwidth
1491 * @RATE_INFO_BW_160: 160 MHz bandwidth
1492 * @RATE_INFO_BW_HE_RU: bandwidth determined by HE RU allocation
1493 */
1494enum rate_info_bw {
1495 RATE_INFO_BW_20 = 0,
1496 RATE_INFO_BW_5,
1497 RATE_INFO_BW_10,
1498 RATE_INFO_BW_40,
1499 RATE_INFO_BW_80,
1500 RATE_INFO_BW_160,
1501 RATE_INFO_BW_HE_RU,
1502};
1503
1504/**
1505 * struct rate_info - bitrate information
1506 *
1507 * Information about a receiving or transmitting bitrate
1508 *
1509 * @flags: bitflag of flags from &enum rate_info_flags
1510 * @mcs: mcs index if struct describes an HT/VHT/HE rate
1511 * @legacy: bitrate in 100kbit/s for 802.11abg
1512 * @nss: number of streams (VHT & HE only)
1513 * @bw: bandwidth (from &enum rate_info_bw)
1514 * @he_gi: HE guard interval (from &enum nl80211_he_gi)
1515 * @he_dcm: HE DCM value
1516 * @he_ru_alloc: HE RU allocation (from &enum nl80211_he_ru_alloc,
1517 * only valid if bw is %RATE_INFO_BW_HE_RU)
1518 * @n_bonded_ch: In case of EDMG the number of bonded channels (1-4)
1519 */
1520struct rate_info {
1521 u8 flags;
1522 u8 mcs;
1523 u16 legacy;
1524 u8 nss;
1525 u8 bw;
1526 u8 he_gi;
1527 u8 he_dcm;
1528 u8 he_ru_alloc;
1529 u8 n_bonded_ch;
1530};
1531
1532/**
1533 * enum bss_param_flags - bitrate info flags
1534 *
1535 * Used by the driver to indicate the specific rate transmission
1536 * type for 802.11n transmissions.
1537 *
1538 * @BSS_PARAM_FLAGS_CTS_PROT: whether CTS protection is enabled
1539 * @BSS_PARAM_FLAGS_SHORT_PREAMBLE: whether short preamble is enabled
1540 * @BSS_PARAM_FLAGS_SHORT_SLOT_TIME: whether short slot time is enabled
1541 */
1542enum bss_param_flags {
1543 BSS_PARAM_FLAGS_CTS_PROT = 1<<0,
1544 BSS_PARAM_FLAGS_SHORT_PREAMBLE = 1<<1,
1545 BSS_PARAM_FLAGS_SHORT_SLOT_TIME = 1<<2,
1546};
1547
1548/**
1549 * struct sta_bss_parameters - BSS parameters for the attached station
1550 *
1551 * Information about the currently associated BSS
1552 *
1553 * @flags: bitflag of flags from &enum bss_param_flags
1554 * @dtim_period: DTIM period for the BSS
1555 * @beacon_interval: beacon interval
1556 */
1557struct sta_bss_parameters {
1558 u8 flags;
1559 u8 dtim_period;
1560 u16 beacon_interval;
1561};
1562
1563/**
1564 * struct cfg80211_txq_stats - TXQ statistics for this TID
1565 * @filled: bitmap of flags using the bits of &enum nl80211_txq_stats to
1566 * indicate the relevant values in this struct are filled
1567 * @backlog_bytes: total number of bytes currently backlogged
1568 * @backlog_packets: total number of packets currently backlogged
1569 * @flows: number of new flows seen
1570 * @drops: total number of packets dropped
1571 * @ecn_marks: total number of packets marked with ECN CE
1572 * @overlimit: number of drops due to queue space overflow
1573 * @overmemory: number of drops due to memory limit overflow
1574 * @collisions: number of hash collisions
1575 * @tx_bytes: total number of bytes dequeued
1576 * @tx_packets: total number of packets dequeued
1577 * @max_flows: maximum number of flows supported
1578 */
1579struct cfg80211_txq_stats {
1580 u32 filled;
1581 u32 backlog_bytes;
1582 u32 backlog_packets;
1583 u32 flows;
1584 u32 drops;
1585 u32 ecn_marks;
1586 u32 overlimit;
1587 u32 overmemory;
1588 u32 collisions;
1589 u32 tx_bytes;
1590 u32 tx_packets;
1591 u32 max_flows;
1592};
1593
1594/**
1595 * struct cfg80211_tid_stats - per-TID statistics
1596 * @filled: bitmap of flags using the bits of &enum nl80211_tid_stats to
1597 * indicate the relevant values in this struct are filled
1598 * @rx_msdu: number of received MSDUs
1599 * @tx_msdu: number of (attempted) transmitted MSDUs
1600 * @tx_msdu_retries: number of retries (not counting the first) for
1601 * transmitted MSDUs
1602 * @tx_msdu_failed: number of failed transmitted MSDUs
1603 * @txq_stats: TXQ statistics
1604 */
1605struct cfg80211_tid_stats {
1606 u32 filled;
1607 u64 rx_msdu;
1608 u64 tx_msdu;
1609 u64 tx_msdu_retries;
1610 u64 tx_msdu_failed;
1611 struct cfg80211_txq_stats txq_stats;
1612};
1613
1614#define IEEE80211_MAX_CHAINS 4
1615
1616/**
1617 * struct station_info - station information
1618 *
1619 * Station information filled by driver for get_station() and dump_station.
1620 *
1621 * @filled: bitflag of flags using the bits of &enum nl80211_sta_info to
1622 * indicate the relevant values in this struct for them
1623 * @connected_time: time(in secs) since a station is last connected
1624 * @inactive_time: time since last station activity (tx/rx) in milliseconds
1625 * @assoc_at: bootime (ns) of the last association
1626 * @rx_bytes: bytes (size of MPDUs) received from this station
1627 * @tx_bytes: bytes (size of MPDUs) transmitted to this station
1628 * @llid: mesh local link id
1629 * @plid: mesh peer link id
1630 * @plink_state: mesh peer link state
1631 * @signal: The signal strength, type depends on the wiphy's signal_type.
1632 * For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_.
1633 * @signal_avg: Average signal strength, type depends on the wiphy's signal_type.
1634 * For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_.
1635 * @chains: bitmask for filled values in @chain_signal, @chain_signal_avg
1636 * @chain_signal: per-chain signal strength of last received packet in dBm
1637 * @chain_signal_avg: per-chain signal strength average in dBm
1638 * @txrate: current unicast bitrate from this station
1639 * @rxrate: current unicast bitrate to this station
1640 * @rx_packets: packets (MSDUs & MMPDUs) received from this station
1641 * @tx_packets: packets (MSDUs & MMPDUs) transmitted to this station
1642 * @tx_retries: cumulative retry counts (MPDUs)
1643 * @tx_failed: number of failed transmissions (MPDUs) (retries exceeded, no ACK)
1644 * @rx_dropped_misc: Dropped for un-specified reason.
1645 * @bss_param: current BSS parameters
1646 * @generation: generation number for nl80211 dumps.
1647 * This number should increase every time the list of stations
1648 * changes, i.e. when a station is added or removed, so that
1649 * userspace can tell whether it got a consistent snapshot.
1650 * @assoc_req_ies: IEs from (Re)Association Request.
1651 * This is used only when in AP mode with drivers that do not use
1652 * user space MLME/SME implementation. The information is provided for
1653 * the cfg80211_new_sta() calls to notify user space of the IEs.
1654 * @assoc_req_ies_len: Length of assoc_req_ies buffer in octets.
1655 * @sta_flags: station flags mask & values
1656 * @beacon_loss_count: Number of times beacon loss event has triggered.
1657 * @t_offset: Time offset of the station relative to this host.
1658 * @local_pm: local mesh STA power save mode
1659 * @peer_pm: peer mesh STA power save mode
1660 * @nonpeer_pm: non-peer mesh STA power save mode
1661 * @expected_throughput: expected throughput in kbps (including 802.11 headers)
1662 * towards this station.
1663 * @rx_beacon: number of beacons received from this peer
1664 * @rx_beacon_signal_avg: signal strength average (in dBm) for beacons received
1665 * from this peer
1666 * @connected_to_gate: true if mesh STA has a path to mesh gate
1667 * @rx_duration: aggregate PPDU duration(usecs) for all the frames from a peer
1668 * @tx_duration: aggregate PPDU duration(usecs) for all the frames to a peer
1669 * @airtime_weight: current airtime scheduling weight
1670 * @pertid: per-TID statistics, see &struct cfg80211_tid_stats, using the last
1671 * (IEEE80211_NUM_TIDS) index for MSDUs not encapsulated in QoS-MPDUs.
1672 * Note that this doesn't use the @filled bit, but is used if non-NULL.
1673 * @ack_signal: signal strength (in dBm) of the last ACK frame.
1674 * @avg_ack_signal: average rssi value of ack packet for the no of msdu's has
1675 * been sent.
1676 * @rx_mpdu_count: number of MPDUs received from this station
1677 * @fcs_err_count: number of packets (MPDUs) received from this station with
1678 * an FCS error. This counter should be incremented only when TA of the
1679 * received packet with an FCS error matches the peer MAC address.
1680 * @airtime_link_metric: mesh airtime link metric.
1681 * @connected_to_as: true if mesh STA has a path to authentication server
1682 */
1683struct station_info {
1684 u64 filled;
1685 u32 connected_time;
1686 u32 inactive_time;
1687 u64 assoc_at;
1688 u64 rx_bytes;
1689 u64 tx_bytes;
1690 u16 llid;
1691 u16 plid;
1692 u8 plink_state;
1693 s8 signal;
1694 s8 signal_avg;
1695
1696 u8 chains;
1697 s8 chain_signal[IEEE80211_MAX_CHAINS];
1698 s8 chain_signal_avg[IEEE80211_MAX_CHAINS];
1699
1700 struct rate_info txrate;
1701 struct rate_info rxrate;
1702 u32 rx_packets;
1703 u32 tx_packets;
1704 u32 tx_retries;
1705 u32 tx_failed;
1706 u32 rx_dropped_misc;
1707 struct sta_bss_parameters bss_param;
1708 struct nl80211_sta_flag_update sta_flags;
1709
1710 int generation;
1711
1712 const u8 *assoc_req_ies;
1713 size_t assoc_req_ies_len;
1714
1715 u32 beacon_loss_count;
1716 s64 t_offset;
1717 enum nl80211_mesh_power_mode local_pm;
1718 enum nl80211_mesh_power_mode peer_pm;
1719 enum nl80211_mesh_power_mode nonpeer_pm;
1720
1721 u32 expected_throughput;
1722
1723 u64 tx_duration;
1724 u64 rx_duration;
1725 u64 rx_beacon;
1726 u8 rx_beacon_signal_avg;
1727 u8 connected_to_gate;
1728
1729 struct cfg80211_tid_stats *pertid;
1730 s8 ack_signal;
1731 s8 avg_ack_signal;
1732
1733 u16 airtime_weight;
1734
1735 u32 rx_mpdu_count;
1736 u32 fcs_err_count;
1737
1738 u32 airtime_link_metric;
1739
1740 u8 connected_to_as;
1741};
1742
1743/**
1744 * struct cfg80211_sar_sub_specs - sub specs limit
1745 * @power: power limitation in 0.25dbm
1746 * @freq_range_index: index the power limitation applies to
1747 */
1748struct cfg80211_sar_sub_specs {
1749 s32 power;
1750 u32 freq_range_index;
1751};
1752
1753/**
1754 * struct cfg80211_sar_specs - sar limit specs
1755 * @type: it's set with power in 0.25dbm or other types
1756 * @num_sub_specs: number of sar sub specs
1757 * @sub_specs: memory to hold the sar sub specs
1758 */
1759struct cfg80211_sar_specs {
1760 enum nl80211_sar_type type;
1761 u32 num_sub_specs;
1762 struct cfg80211_sar_sub_specs sub_specs[];
1763};
1764
1765
1766/**
1767 * struct cfg80211_sar_freq_ranges - sar frequency ranges
1768 * @start_freq: start range edge frequency
1769 * @end_freq: end range edge frequency
1770 */
1771struct cfg80211_sar_freq_ranges {
1772 u32 start_freq;
1773 u32 end_freq;
1774};
1775
1776/**
1777 * struct cfg80211_sar_capa - sar limit capability
1778 * @type: it's set via power in 0.25dbm or other types
1779 * @num_freq_ranges: number of frequency ranges
1780 * @freq_ranges: memory to hold the freq ranges.
1781 *
1782 * Note: WLAN driver may append new ranges or split an existing
1783 * range to small ones and then append them.
1784 */
1785struct cfg80211_sar_capa {
1786 enum nl80211_sar_type type;
1787 u32 num_freq_ranges;
1788 const struct cfg80211_sar_freq_ranges *freq_ranges;
1789};
1790
1791#if IS_ENABLED(CONFIG_CFG80211)
1792/**
1793 * cfg80211_get_station - retrieve information about a given station
1794 * @dev: the device where the station is supposed to be connected to
1795 * @mac_addr: the mac address of the station of interest
1796 * @sinfo: pointer to the structure to fill with the information
1797 *
1798 * Returns 0 on success and sinfo is filled with the available information
1799 * otherwise returns a negative error code and the content of sinfo has to be
1800 * considered undefined.
1801 */
1802int cfg80211_get_station(struct net_device *dev, const u8 *mac_addr,
1803 struct station_info *sinfo);
1804#else
1805static inline int cfg80211_get_station(struct net_device *dev,
1806 const u8 *mac_addr,
1807 struct station_info *sinfo)
1808{
1809 return -ENOENT;
1810}
1811#endif
1812
1813/**
1814 * enum monitor_flags - monitor flags
1815 *
1816 * Monitor interface configuration flags. Note that these must be the bits
1817 * according to the nl80211 flags.
1818 *
1819 * @MONITOR_FLAG_CHANGED: set if the flags were changed
1820 * @MONITOR_FLAG_FCSFAIL: pass frames with bad FCS
1821 * @MONITOR_FLAG_PLCPFAIL: pass frames with bad PLCP
1822 * @MONITOR_FLAG_CONTROL: pass control frames
1823 * @MONITOR_FLAG_OTHER_BSS: disable BSSID filtering
1824 * @MONITOR_FLAG_COOK_FRAMES: report frames after processing
1825 * @MONITOR_FLAG_ACTIVE: active monitor, ACKs frames on its MAC address
1826 */
1827enum monitor_flags {
1828 MONITOR_FLAG_CHANGED = 1<<__NL80211_MNTR_FLAG_INVALID,
1829 MONITOR_FLAG_FCSFAIL = 1<<NL80211_MNTR_FLAG_FCSFAIL,
1830 MONITOR_FLAG_PLCPFAIL = 1<<NL80211_MNTR_FLAG_PLCPFAIL,
1831 MONITOR_FLAG_CONTROL = 1<<NL80211_MNTR_FLAG_CONTROL,
1832 MONITOR_FLAG_OTHER_BSS = 1<<NL80211_MNTR_FLAG_OTHER_BSS,
1833 MONITOR_FLAG_COOK_FRAMES = 1<<NL80211_MNTR_FLAG_COOK_FRAMES,
1834 MONITOR_FLAG_ACTIVE = 1<<NL80211_MNTR_FLAG_ACTIVE,
1835};
1836
1837/**
1838 * enum mpath_info_flags - mesh path information flags
1839 *
1840 * Used by the driver to indicate which info in &struct mpath_info it has filled
1841 * in during get_station() or dump_station().
1842 *
1843 * @MPATH_INFO_FRAME_QLEN: @frame_qlen filled
1844 * @MPATH_INFO_SN: @sn filled
1845 * @MPATH_INFO_METRIC: @metric filled
1846 * @MPATH_INFO_EXPTIME: @exptime filled
1847 * @MPATH_INFO_DISCOVERY_TIMEOUT: @discovery_timeout filled
1848 * @MPATH_INFO_DISCOVERY_RETRIES: @discovery_retries filled
1849 * @MPATH_INFO_FLAGS: @flags filled
1850 * @MPATH_INFO_HOP_COUNT: @hop_count filled
1851 * @MPATH_INFO_PATH_CHANGE: @path_change_count filled
1852 */
1853enum mpath_info_flags {
1854 MPATH_INFO_FRAME_QLEN = BIT(0),
1855 MPATH_INFO_SN = BIT(1),
1856 MPATH_INFO_METRIC = BIT(2),
1857 MPATH_INFO_EXPTIME = BIT(3),
1858 MPATH_INFO_DISCOVERY_TIMEOUT = BIT(4),
1859 MPATH_INFO_DISCOVERY_RETRIES = BIT(5),
1860 MPATH_INFO_FLAGS = BIT(6),
1861 MPATH_INFO_HOP_COUNT = BIT(7),
1862 MPATH_INFO_PATH_CHANGE = BIT(8),
1863};
1864
1865/**
1866 * struct mpath_info - mesh path information
1867 *
1868 * Mesh path information filled by driver for get_mpath() and dump_mpath().
1869 *
1870 * @filled: bitfield of flags from &enum mpath_info_flags
1871 * @frame_qlen: number of queued frames for this destination
1872 * @sn: target sequence number
1873 * @metric: metric (cost) of this mesh path
1874 * @exptime: expiration time for the mesh path from now, in msecs
1875 * @flags: mesh path flags
1876 * @discovery_timeout: total mesh path discovery timeout, in msecs
1877 * @discovery_retries: mesh path discovery retries
1878 * @generation: generation number for nl80211 dumps.
1879 * This number should increase every time the list of mesh paths
1880 * changes, i.e. when a station is added or removed, so that
1881 * userspace can tell whether it got a consistent snapshot.
1882 * @hop_count: hops to destination
1883 * @path_change_count: total number of path changes to destination
1884 */
1885struct mpath_info {
1886 u32 filled;
1887 u32 frame_qlen;
1888 u32 sn;
1889 u32 metric;
1890 u32 exptime;
1891 u32 discovery_timeout;
1892 u8 discovery_retries;
1893 u8 flags;
1894 u8 hop_count;
1895 u32 path_change_count;
1896
1897 int generation;
1898};
1899
1900/**
1901 * struct bss_parameters - BSS parameters
1902 *
1903 * Used to change BSS parameters (mainly for AP mode).
1904 *
1905 * @use_cts_prot: Whether to use CTS protection
1906 * (0 = no, 1 = yes, -1 = do not change)
1907 * @use_short_preamble: Whether the use of short preambles is allowed
1908 * (0 = no, 1 = yes, -1 = do not change)
1909 * @use_short_slot_time: Whether the use of short slot time is allowed
1910 * (0 = no, 1 = yes, -1 = do not change)
1911 * @basic_rates: basic rates in IEEE 802.11 format
1912 * (or NULL for no change)
1913 * @basic_rates_len: number of basic rates
1914 * @ap_isolate: do not forward packets between connected stations
1915 * (0 = no, 1 = yes, -1 = do not change)
1916 * @ht_opmode: HT Operation mode
1917 * (u16 = opmode, -1 = do not change)
1918 * @p2p_ctwindow: P2P CT Window (-1 = no change)
1919 * @p2p_opp_ps: P2P opportunistic PS (-1 = no change)
1920 */
1921struct bss_parameters {
1922 int use_cts_prot;
1923 int use_short_preamble;
1924 int use_short_slot_time;
1925 const u8 *basic_rates;
1926 u8 basic_rates_len;
1927 int ap_isolate;
1928 int ht_opmode;
1929 s8 p2p_ctwindow, p2p_opp_ps;
1930};
1931
1932/**
1933 * struct mesh_config - 802.11s mesh configuration
1934 *
1935 * These parameters can be changed while the mesh is active.
1936 *
1937 * @dot11MeshRetryTimeout: the initial retry timeout in millisecond units used
1938 * by the Mesh Peering Open message
1939 * @dot11MeshConfirmTimeout: the initial retry timeout in millisecond units
1940 * used by the Mesh Peering Open message
1941 * @dot11MeshHoldingTimeout: the confirm timeout in millisecond units used by
1942 * the mesh peering management to close a mesh peering
1943 * @dot11MeshMaxPeerLinks: the maximum number of peer links allowed on this
1944 * mesh interface
1945 * @dot11MeshMaxRetries: the maximum number of peer link open retries that can
1946 * be sent to establish a new peer link instance in a mesh
1947 * @dot11MeshTTL: the value of TTL field set at a source mesh STA
1948 * @element_ttl: the value of TTL field set at a mesh STA for path selection
1949 * elements
1950 * @auto_open_plinks: whether we should automatically open peer links when we
1951 * detect compatible mesh peers
1952 * @dot11MeshNbrOffsetMaxNeighbor: the maximum number of neighbors to
1953 * synchronize to for 11s default synchronization method
1954 * @dot11MeshHWMPmaxPREQretries: the number of action frames containing a PREQ
1955 * that an originator mesh STA can send to a particular path target
1956 * @path_refresh_time: how frequently to refresh mesh paths in milliseconds
1957 * @min_discovery_timeout: the minimum length of time to wait until giving up on
1958 * a path discovery in milliseconds
1959 * @dot11MeshHWMPactivePathTimeout: the time (in TUs) for which mesh STAs
1960 * receiving a PREQ shall consider the forwarding information from the
1961 * root to be valid. (TU = time unit)
1962 * @dot11MeshHWMPpreqMinInterval: the minimum interval of time (in TUs) during
1963 * which a mesh STA can send only one action frame containing a PREQ
1964 * element
1965 * @dot11MeshHWMPperrMinInterval: the minimum interval of time (in TUs) during
1966 * which a mesh STA can send only one Action frame containing a PERR
1967 * element
1968 * @dot11MeshHWMPnetDiameterTraversalTime: the interval of time (in TUs) that
1969 * it takes for an HWMP information element to propagate across the mesh
1970 * @dot11MeshHWMPRootMode: the configuration of a mesh STA as root mesh STA
1971 * @dot11MeshHWMPRannInterval: the interval of time (in TUs) between root
1972 * announcements are transmitted
1973 * @dot11MeshGateAnnouncementProtocol: whether to advertise that this mesh
1974 * station has access to a broader network beyond the MBSS. (This is
1975 * missnamed in draft 12.0: dot11MeshGateAnnouncementProtocol set to true
1976 * only means that the station will announce others it's a mesh gate, but
1977 * not necessarily using the gate announcement protocol. Still keeping the
1978 * same nomenclature to be in sync with the spec)
1979 * @dot11MeshForwarding: whether the Mesh STA is forwarding or non-forwarding
1980 * entity (default is TRUE - forwarding entity)
1981 * @rssi_threshold: the threshold for average signal strength of candidate
1982 * station to establish a peer link
1983 * @ht_opmode: mesh HT protection mode
1984 *
1985 * @dot11MeshHWMPactivePathToRootTimeout: The time (in TUs) for which mesh STAs
1986 * receiving a proactive PREQ shall consider the forwarding information to
1987 * the root mesh STA to be valid.
1988 *
1989 * @dot11MeshHWMProotInterval: The interval of time (in TUs) between proactive
1990 * PREQs are transmitted.
1991 * @dot11MeshHWMPconfirmationInterval: The minimum interval of time (in TUs)
1992 * during which a mesh STA can send only one Action frame containing
1993 * a PREQ element for root path confirmation.
1994 * @power_mode: The default mesh power save mode which will be the initial
1995 * setting for new peer links.
1996 * @dot11MeshAwakeWindowDuration: The duration in TUs the STA will remain awake
1997 * after transmitting its beacon.
1998 * @plink_timeout: If no tx activity is seen from a STA we've established
1999 * peering with for longer than this time (in seconds), then remove it
2000 * from the STA's list of peers. Default is 30 minutes.
2001 * @dot11MeshConnectedToMeshGate: if set to true, advertise that this STA is
2002 * connected to a mesh gate in mesh formation info. If false, the
2003 * value in mesh formation is determined by the presence of root paths
2004 * in the mesh path table
2005 * @dot11MeshNolearn: Try to avoid multi-hop path discovery (e.g. PREQ/PREP
2006 * for HWMP) if the destination is a direct neighbor. Note that this might
2007 * not be the optimal decision as a multi-hop route might be better. So
2008 * if using this setting you will likely also want to disable
2009 * dot11MeshForwarding and use another mesh routing protocol on top.
2010 */
2011struct mesh_config {
2012 u16 dot11MeshRetryTimeout;
2013 u16 dot11MeshConfirmTimeout;
2014 u16 dot11MeshHoldingTimeout;
2015 u16 dot11MeshMaxPeerLinks;
2016 u8 dot11MeshMaxRetries;
2017 u8 dot11MeshTTL;
2018 u8 element_ttl;
2019 bool auto_open_plinks;
2020 u32 dot11MeshNbrOffsetMaxNeighbor;
2021 u8 dot11MeshHWMPmaxPREQretries;
2022 u32 path_refresh_time;
2023 u16 min_discovery_timeout;
2024 u32 dot11MeshHWMPactivePathTimeout;
2025 u16 dot11MeshHWMPpreqMinInterval;
2026 u16 dot11MeshHWMPperrMinInterval;
2027 u16 dot11MeshHWMPnetDiameterTraversalTime;
2028 u8 dot11MeshHWMPRootMode;
2029 bool dot11MeshConnectedToMeshGate;
2030 bool dot11MeshConnectedToAuthServer;
2031 u16 dot11MeshHWMPRannInterval;
2032 bool dot11MeshGateAnnouncementProtocol;
2033 bool dot11MeshForwarding;
2034 s32 rssi_threshold;
2035 u16 ht_opmode;
2036 u32 dot11MeshHWMPactivePathToRootTimeout;
2037 u16 dot11MeshHWMProotInterval;
2038 u16 dot11MeshHWMPconfirmationInterval;
2039 enum nl80211_mesh_power_mode power_mode;
2040 u16 dot11MeshAwakeWindowDuration;
2041 u32 plink_timeout;
2042 bool dot11MeshNolearn;
2043};
2044
2045/**
2046 * struct mesh_setup - 802.11s mesh setup configuration
2047 * @chandef: defines the channel to use
2048 * @mesh_id: the mesh ID
2049 * @mesh_id_len: length of the mesh ID, at least 1 and at most 32 bytes
2050 * @sync_method: which synchronization method to use
2051 * @path_sel_proto: which path selection protocol to use
2052 * @path_metric: which metric to use
2053 * @auth_id: which authentication method this mesh is using
2054 * @ie: vendor information elements (optional)
2055 * @ie_len: length of vendor information elements
2056 * @is_authenticated: this mesh requires authentication
2057 * @is_secure: this mesh uses security
2058 * @user_mpm: userspace handles all MPM functions
2059 * @dtim_period: DTIM period to use
2060 * @beacon_interval: beacon interval to use
2061 * @mcast_rate: multicat rate for Mesh Node [6Mbps is the default for 802.11a]
2062 * @basic_rates: basic rates to use when creating the mesh
2063 * @beacon_rate: bitrate to be used for beacons
2064 * @userspace_handles_dfs: whether user space controls DFS operation, i.e.
2065 * changes the channel when a radar is detected. This is required
2066 * to operate on DFS channels.
2067 * @control_port_over_nl80211: TRUE if userspace expects to exchange control
2068 * port frames over NL80211 instead of the network interface.
2069 *
2070 * These parameters are fixed when the mesh is created.
2071 */
2072struct mesh_setup {
2073 struct cfg80211_chan_def chandef;
2074 const u8 *mesh_id;
2075 u8 mesh_id_len;
2076 u8 sync_method;
2077 u8 path_sel_proto;
2078 u8 path_metric;
2079 u8 auth_id;
2080 const u8 *ie;
2081 u8 ie_len;
2082 bool is_authenticated;
2083 bool is_secure;
2084 bool user_mpm;
2085 u8 dtim_period;
2086 u16 beacon_interval;
2087 int mcast_rate[NUM_NL80211_BANDS];
2088 u32 basic_rates;
2089 struct cfg80211_bitrate_mask beacon_rate;
2090 bool userspace_handles_dfs;
2091 bool control_port_over_nl80211;
2092};
2093
2094/**
2095 * struct ocb_setup - 802.11p OCB mode setup configuration
2096 * @chandef: defines the channel to use
2097 *
2098 * These parameters are fixed when connecting to the network
2099 */
2100struct ocb_setup {
2101 struct cfg80211_chan_def chandef;
2102};
2103
2104/**
2105 * struct ieee80211_txq_params - TX queue parameters
2106 * @ac: AC identifier
2107 * @txop: Maximum burst time in units of 32 usecs, 0 meaning disabled
2108 * @cwmin: Minimum contention window [a value of the form 2^n-1 in the range
2109 * 1..32767]
2110 * @cwmax: Maximum contention window [a value of the form 2^n-1 in the range
2111 * 1..32767]
2112 * @aifs: Arbitration interframe space [0..255]
2113 */
2114struct ieee80211_txq_params {
2115 enum nl80211_ac ac;
2116 u16 txop;
2117 u16 cwmin;
2118 u16 cwmax;
2119 u8 aifs;
2120};
2121
2122/**
2123 * DOC: Scanning and BSS list handling
2124 *
2125 * The scanning process itself is fairly simple, but cfg80211 offers quite
2126 * a bit of helper functionality. To start a scan, the scan operation will
2127 * be invoked with a scan definition. This scan definition contains the
2128 * channels to scan, and the SSIDs to send probe requests for (including the
2129 * wildcard, if desired). A passive scan is indicated by having no SSIDs to
2130 * probe. Additionally, a scan request may contain extra information elements
2131 * that should be added to the probe request. The IEs are guaranteed to be
2132 * well-formed, and will not exceed the maximum length the driver advertised
2133 * in the wiphy structure.
2134 *
2135 * When scanning finds a BSS, cfg80211 needs to be notified of that, because
2136 * it is responsible for maintaining the BSS list; the driver should not
2137 * maintain a list itself. For this notification, various functions exist.
2138 *
2139 * Since drivers do not maintain a BSS list, there are also a number of
2140 * functions to search for a BSS and obtain information about it from the
2141 * BSS structure cfg80211 maintains. The BSS list is also made available
2142 * to userspace.
2143 */
2144
2145/**
2146 * struct cfg80211_ssid - SSID description
2147 * @ssid: the SSID
2148 * @ssid_len: length of the ssid
2149 */
2150struct cfg80211_ssid {
2151 u8 ssid[IEEE80211_MAX_SSID_LEN];
2152 u8 ssid_len;
2153};
2154
2155/**
2156 * struct cfg80211_scan_info - information about completed scan
2157 * @scan_start_tsf: scan start time in terms of the TSF of the BSS that the
2158 * wireless device that requested the scan is connected to. If this
2159 * information is not available, this field is left zero.
2160 * @tsf_bssid: the BSSID according to which %scan_start_tsf is set.
2161 * @aborted: set to true if the scan was aborted for any reason,
2162 * userspace will be notified of that
2163 */
2164struct cfg80211_scan_info {
2165 u64 scan_start_tsf;
2166 u8 tsf_bssid[ETH_ALEN] __aligned(2);
2167 bool aborted;
2168};
2169
2170/**
2171 * struct cfg80211_scan_6ghz_params - relevant for 6 GHz only
2172 *
2173 * @short_bssid: short ssid to scan for
2174 * @bssid: bssid to scan for
2175 * @channel_idx: idx of the channel in the channel array in the scan request
2176 * which the above info relvant to
2177 * @unsolicited_probe: the AP transmits unsolicited probe response every 20 TU
2178 * @short_ssid_valid: short_ssid is valid and can be used
2179 * @psc_no_listen: when set, and the channel is a PSC channel, no need to wait
2180 * 20 TUs before starting to send probe requests.
2181 */
2182struct cfg80211_scan_6ghz_params {
2183 u32 short_ssid;
2184 u32 channel_idx;
2185 u8 bssid[ETH_ALEN];
2186 bool unsolicited_probe;
2187 bool short_ssid_valid;
2188 bool psc_no_listen;
2189};
2190
2191/**
2192 * struct cfg80211_scan_request - scan request description
2193 *
2194 * @ssids: SSIDs to scan for (active scan only)
2195 * @n_ssids: number of SSIDs
2196 * @channels: channels to scan on.
2197 * @n_channels: total number of channels to scan
2198 * @scan_width: channel width for scanning
2199 * @ie: optional information element(s) to add into Probe Request or %NULL
2200 * @ie_len: length of ie in octets
2201 * @duration: how long to listen on each channel, in TUs. If
2202 * %duration_mandatory is not set, this is the maximum dwell time and
2203 * the actual dwell time may be shorter.
2204 * @duration_mandatory: if set, the scan duration must be as specified by the
2205 * %duration field.
2206 * @flags: bit field of flags controlling operation
2207 * @rates: bitmap of rates to advertise for each band
2208 * @wiphy: the wiphy this was for
2209 * @scan_start: time (in jiffies) when the scan started
2210 * @wdev: the wireless device to scan for
2211 * @info: (internal) information about completed scan
2212 * @notified: (internal) scan request was notified as done or aborted
2213 * @no_cck: used to send probe requests at non CCK rate in 2GHz band
2214 * @mac_addr: MAC address used with randomisation
2215 * @mac_addr_mask: MAC address mask used with randomisation, bits that
2216 * are 0 in the mask should be randomised, bits that are 1 should
2217 * be taken from the @mac_addr
2218 * @scan_6ghz: relevant for split scan request only,
2219 * true if this is the second scan request
2220 * @n_6ghz_params: number of 6 GHz params
2221 * @scan_6ghz_params: 6 GHz params
2222 * @bssid: BSSID to scan for (most commonly, the wildcard BSSID)
2223 */
2224struct cfg80211_scan_request {
2225 struct cfg80211_ssid *ssids;
2226 int n_ssids;
2227 u32 n_channels;
2228 enum nl80211_bss_scan_width scan_width;
2229 const u8 *ie;
2230 size_t ie_len;
2231 u16 duration;
2232 bool duration_mandatory;
2233 u32 flags;
2234
2235 u32 rates[NUM_NL80211_BANDS];
2236
2237 struct wireless_dev *wdev;
2238
2239 u8 mac_addr[ETH_ALEN] __aligned(2);
2240 u8 mac_addr_mask[ETH_ALEN] __aligned(2);
2241 u8 bssid[ETH_ALEN] __aligned(2);
2242
2243 /* internal */
2244 struct wiphy *wiphy;
2245 unsigned long scan_start;
2246 struct cfg80211_scan_info info;
2247 bool notified;
2248 bool no_cck;
2249 bool scan_6ghz;
2250 u32 n_6ghz_params;
2251 struct cfg80211_scan_6ghz_params *scan_6ghz_params;
2252
2253 /* keep last */
2254 struct ieee80211_channel *channels[];
2255};
2256
2257static inline void get_random_mask_addr(u8 *buf, const u8 *addr, const u8 *mask)
2258{
2259 int i;
2260
2261 get_random_bytes(buf, ETH_ALEN);
2262 for (i = 0; i < ETH_ALEN; i++) {
2263 buf[i] &= ~mask[i];
2264 buf[i] |= addr[i] & mask[i];
2265 }
2266}
2267
2268/**
2269 * struct cfg80211_match_set - sets of attributes to match
2270 *
2271 * @ssid: SSID to be matched; may be zero-length in case of BSSID match
2272 * or no match (RSSI only)
2273 * @bssid: BSSID to be matched; may be all-zero BSSID in case of SSID match
2274 * or no match (RSSI only)
2275 * @rssi_thold: don't report scan results below this threshold (in s32 dBm)
2276 * @per_band_rssi_thold: Minimum rssi threshold for each band to be applied
2277 * for filtering out scan results received. Drivers advertize this support
2278 * of band specific rssi based filtering through the feature capability
2279 * %NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD. These band
2280 * specific rssi thresholds take precedence over rssi_thold, if specified.
2281 * If not specified for any band, it will be assigned with rssi_thold of
2282 * corresponding matchset.
2283 */
2284struct cfg80211_match_set {
2285 struct cfg80211_ssid ssid;
2286 u8 bssid[ETH_ALEN];
2287 s32 rssi_thold;
2288 s32 per_band_rssi_thold[NUM_NL80211_BANDS];
2289};
2290
2291/**
2292 * struct cfg80211_sched_scan_plan - scan plan for scheduled scan
2293 *
2294 * @interval: interval between scheduled scan iterations. In seconds.
2295 * @iterations: number of scan iterations in this scan plan. Zero means
2296 * infinite loop.
2297 * The last scan plan will always have this parameter set to zero,
2298 * all other scan plans will have a finite number of iterations.
2299 */
2300struct cfg80211_sched_scan_plan {
2301 u32 interval;
2302 u32 iterations;
2303};
2304
2305/**
2306 * struct cfg80211_bss_select_adjust - BSS selection with RSSI adjustment.
2307 *
2308 * @band: band of BSS which should match for RSSI level adjustment.
2309 * @delta: value of RSSI level adjustment.
2310 */
2311struct cfg80211_bss_select_adjust {
2312 enum nl80211_band band;
2313 s8 delta;
2314};
2315
2316/**
2317 * struct cfg80211_sched_scan_request - scheduled scan request description
2318 *
2319 * @reqid: identifies this request.
2320 * @ssids: SSIDs to scan for (passed in the probe_reqs in active scans)
2321 * @n_ssids: number of SSIDs
2322 * @n_channels: total number of channels to scan
2323 * @scan_width: channel width for scanning
2324 * @ie: optional information element(s) to add into Probe Request or %NULL
2325 * @ie_len: length of ie in octets
2326 * @flags: bit field of flags controlling operation
2327 * @match_sets: sets of parameters to be matched for a scan result
2328 * entry to be considered valid and to be passed to the host
2329 * (others are filtered out).
2330 * If ommited, all results are passed.
2331 * @n_match_sets: number of match sets
2332 * @report_results: indicates that results were reported for this request
2333 * @wiphy: the wiphy this was for
2334 * @dev: the interface
2335 * @scan_start: start time of the scheduled scan
2336 * @channels: channels to scan
2337 * @min_rssi_thold: for drivers only supporting a single threshold, this
2338 * contains the minimum over all matchsets
2339 * @mac_addr: MAC address used with randomisation
2340 * @mac_addr_mask: MAC address mask used with randomisation, bits that
2341 * are 0 in the mask should be randomised, bits that are 1 should
2342 * be taken from the @mac_addr
2343 * @scan_plans: scan plans to be executed in this scheduled scan. Lowest
2344 * index must be executed first.
2345 * @n_scan_plans: number of scan plans, at least 1.
2346 * @rcu_head: RCU callback used to free the struct
2347 * @owner_nlportid: netlink portid of owner (if this should is a request
2348 * owned by a particular socket)
2349 * @nl_owner_dead: netlink owner socket was closed - this request be freed
2350 * @list: for keeping list of requests.
2351 * @delay: delay in seconds to use before starting the first scan
2352 * cycle. The driver may ignore this parameter and start
2353 * immediately (or at any other time), if this feature is not
2354 * supported.
2355 * @relative_rssi_set: Indicates whether @relative_rssi is set or not.
2356 * @relative_rssi: Relative RSSI threshold in dB to restrict scan result
2357 * reporting in connected state to cases where a matching BSS is determined
2358 * to have better or slightly worse RSSI than the current connected BSS.
2359 * The relative RSSI threshold values are ignored in disconnected state.
2360 * @rssi_adjust: delta dB of RSSI preference to be given to the BSSs that belong
2361 * to the specified band while deciding whether a better BSS is reported
2362 * using @relative_rssi. If delta is a negative number, the BSSs that
2363 * belong to the specified band will be penalized by delta dB in relative
2364 * comparisions.
2365 */
2366struct cfg80211_sched_scan_request {
2367 u64 reqid;
2368 struct cfg80211_ssid *ssids;
2369 int n_ssids;
2370 u32 n_channels;
2371 enum nl80211_bss_scan_width scan_width;
2372 const u8 *ie;
2373 size_t ie_len;
2374 u32 flags;
2375 struct cfg80211_match_set *match_sets;
2376 int n_match_sets;
2377 s32 min_rssi_thold;
2378 u32 delay;
2379 struct cfg80211_sched_scan_plan *scan_plans;
2380 int n_scan_plans;
2381
2382 u8 mac_addr[ETH_ALEN] __aligned(2);
2383 u8 mac_addr_mask[ETH_ALEN] __aligned(2);
2384
2385 bool relative_rssi_set;
2386 s8 relative_rssi;
2387 struct cfg80211_bss_select_adjust rssi_adjust;
2388
2389 /* internal */
2390 struct wiphy *wiphy;
2391 struct net_device *dev;
2392 unsigned long scan_start;
2393 bool report_results;
2394 struct rcu_head rcu_head;
2395 u32 owner_nlportid;
2396 bool nl_owner_dead;
2397 struct list_head list;
2398
2399 /* keep last */
2400 struct ieee80211_channel *channels[];
2401};
2402
2403/**
2404 * enum cfg80211_signal_type - signal type
2405 *
2406 * @CFG80211_SIGNAL_TYPE_NONE: no signal strength information available
2407 * @CFG80211_SIGNAL_TYPE_MBM: signal strength in mBm (100*dBm)
2408 * @CFG80211_SIGNAL_TYPE_UNSPEC: signal strength, increasing from 0 through 100
2409 */
2410enum cfg80211_signal_type {
2411 CFG80211_SIGNAL_TYPE_NONE,
2412 CFG80211_SIGNAL_TYPE_MBM,
2413 CFG80211_SIGNAL_TYPE_UNSPEC,
2414};
2415
2416/**
2417 * struct cfg80211_inform_bss - BSS inform data
2418 * @chan: channel the frame was received on
2419 * @scan_width: scan width that was used
2420 * @signal: signal strength value, according to the wiphy's
2421 * signal type
2422 * @boottime_ns: timestamp (CLOCK_BOOTTIME) when the information was
2423 * received; should match the time when the frame was actually
2424 * received by the device (not just by the host, in case it was
2425 * buffered on the device) and be accurate to about 10ms.
2426 * If the frame isn't buffered, just passing the return value of
2427 * ktime_get_boottime_ns() is likely appropriate.
2428 * @parent_tsf: the time at the start of reception of the first octet of the
2429 * timestamp field of the frame. The time is the TSF of the BSS specified
2430 * by %parent_bssid.
2431 * @parent_bssid: the BSS according to which %parent_tsf is set. This is set to
2432 * the BSS that requested the scan in which the beacon/probe was received.
2433 * @chains: bitmask for filled values in @chain_signal.
2434 * @chain_signal: per-chain signal strength of last received BSS in dBm.
2435 */
2436struct cfg80211_inform_bss {
2437 struct ieee80211_channel *chan;
2438 enum nl80211_bss_scan_width scan_width;
2439 s32 signal;
2440 u64 boottime_ns;
2441 u64 parent_tsf;
2442 u8 parent_bssid[ETH_ALEN] __aligned(2);
2443 u8 chains;
2444 s8 chain_signal[IEEE80211_MAX_CHAINS];
2445};
2446
2447/**
2448 * struct cfg80211_bss_ies - BSS entry IE data
2449 * @tsf: TSF contained in the frame that carried these IEs
2450 * @rcu_head: internal use, for freeing
2451 * @len: length of the IEs
2452 * @from_beacon: these IEs are known to come from a beacon
2453 * @data: IE data
2454 */
2455struct cfg80211_bss_ies {
2456 u64 tsf;
2457 struct rcu_head rcu_head;
2458 int len;
2459 bool from_beacon;
2460 u8 data[];
2461};
2462
2463/**
2464 * struct cfg80211_bss - BSS description
2465 *
2466 * This structure describes a BSS (which may also be a mesh network)
2467 * for use in scan results and similar.
2468 *
2469 * @channel: channel this BSS is on
2470 * @scan_width: width of the control channel
2471 * @bssid: BSSID of the BSS
2472 * @beacon_interval: the beacon interval as from the frame
2473 * @capability: the capability field in host byte order
2474 * @ies: the information elements (Note that there is no guarantee that these
2475 * are well-formed!); this is a pointer to either the beacon_ies or
2476 * proberesp_ies depending on whether Probe Response frame has been
2477 * received. It is always non-%NULL.
2478 * @beacon_ies: the information elements from the last Beacon frame
2479 * (implementation note: if @hidden_beacon_bss is set this struct doesn't
2480 * own the beacon_ies, but they're just pointers to the ones from the
2481 * @hidden_beacon_bss struct)
2482 * @proberesp_ies: the information elements from the last Probe Response frame
2483 * @hidden_beacon_bss: in case this BSS struct represents a probe response from
2484 * a BSS that hides the SSID in its beacon, this points to the BSS struct
2485 * that holds the beacon data. @beacon_ies is still valid, of course, and
2486 * points to the same data as hidden_beacon_bss->beacon_ies in that case.
2487 * @transmitted_bss: pointer to the transmitted BSS, if this is a
2488 * non-transmitted one (multi-BSSID support)
2489 * @nontrans_list: list of non-transmitted BSS, if this is a transmitted one
2490 * (multi-BSSID support)
2491 * @signal: signal strength value (type depends on the wiphy's signal_type)
2492 * @chains: bitmask for filled values in @chain_signal.
2493 * @chain_signal: per-chain signal strength of last received BSS in dBm.
2494 * @bssid_index: index in the multiple BSS set
2495 * @max_bssid_indicator: max number of members in the BSS set
2496 * @priv: private area for driver use, has at least wiphy->bss_priv_size bytes
2497 */
2498struct cfg80211_bss {
2499 struct ieee80211_channel *channel;
2500 enum nl80211_bss_scan_width scan_width;
2501
2502 const struct cfg80211_bss_ies __rcu *ies;
2503 const struct cfg80211_bss_ies __rcu *beacon_ies;
2504 const struct cfg80211_bss_ies __rcu *proberesp_ies;
2505
2506 struct cfg80211_bss *hidden_beacon_bss;
2507 struct cfg80211_bss *transmitted_bss;
2508 struct list_head nontrans_list;
2509
2510 s32 signal;
2511
2512 u16 beacon_interval;
2513 u16 capability;
2514
2515 u8 bssid[ETH_ALEN];
2516 u8 chains;
2517 s8 chain_signal[IEEE80211_MAX_CHAINS];
2518
2519 u8 bssid_index;
2520 u8 max_bssid_indicator;
2521
2522 u8 priv[] __aligned(sizeof(void *));
2523};
2524
2525/**
2526 * ieee80211_bss_get_elem - find element with given ID
2527 * @bss: the bss to search
2528 * @id: the element ID
2529 *
2530 * Note that the return value is an RCU-protected pointer, so
2531 * rcu_read_lock() must be held when calling this function.
2532 * Return: %NULL if not found.
2533 */
2534const struct element *ieee80211_bss_get_elem(struct cfg80211_bss *bss, u8 id);
2535
2536/**
2537 * ieee80211_bss_get_ie - find IE with given ID
2538 * @bss: the bss to search
2539 * @id: the element ID
2540 *
2541 * Note that the return value is an RCU-protected pointer, so
2542 * rcu_read_lock() must be held when calling this function.
2543 * Return: %NULL if not found.
2544 */
2545static inline const u8 *ieee80211_bss_get_ie(struct cfg80211_bss *bss, u8 id)
2546{
2547 return (void *)ieee80211_bss_get_elem(bss, id);
2548}
2549
2550
2551/**
2552 * struct cfg80211_auth_request - Authentication request data
2553 *
2554 * This structure provides information needed to complete IEEE 802.11
2555 * authentication.
2556 *
2557 * @bss: The BSS to authenticate with, the callee must obtain a reference
2558 * to it if it needs to keep it.
2559 * @auth_type: Authentication type (algorithm)
2560 * @ie: Extra IEs to add to Authentication frame or %NULL
2561 * @ie_len: Length of ie buffer in octets
2562 * @key_len: length of WEP key for shared key authentication
2563 * @key_idx: index of WEP key for shared key authentication
2564 * @key: WEP key for shared key authentication
2565 * @auth_data: Fields and elements in Authentication frames. This contains
2566 * the authentication frame body (non-IE and IE data), excluding the
2567 * Authentication algorithm number, i.e., starting at the Authentication
2568 * transaction sequence number field.
2569 * @auth_data_len: Length of auth_data buffer in octets
2570 */
2571struct cfg80211_auth_request {
2572 struct cfg80211_bss *bss;
2573 const u8 *ie;
2574 size_t ie_len;
2575 enum nl80211_auth_type auth_type;
2576 const u8 *key;
2577 u8 key_len, key_idx;
2578 const u8 *auth_data;
2579 size_t auth_data_len;
2580};
2581
2582/**
2583 * enum cfg80211_assoc_req_flags - Over-ride default behaviour in association.
2584 *
2585 * @ASSOC_REQ_DISABLE_HT: Disable HT (802.11n)
2586 * @ASSOC_REQ_DISABLE_VHT: Disable VHT
2587 * @ASSOC_REQ_USE_RRM: Declare RRM capability in this association
2588 * @CONNECT_REQ_EXTERNAL_AUTH_SUPPORT: User space indicates external
2589 * authentication capability. Drivers can offload authentication to
2590 * userspace if this flag is set. Only applicable for cfg80211_connect()
2591 * request (connect callback).
2592 * @ASSOC_REQ_DISABLE_HE: Disable HE
2593 */
2594enum cfg80211_assoc_req_flags {
2595 ASSOC_REQ_DISABLE_HT = BIT(0),
2596 ASSOC_REQ_DISABLE_VHT = BIT(1),
2597 ASSOC_REQ_USE_RRM = BIT(2),
2598 CONNECT_REQ_EXTERNAL_AUTH_SUPPORT = BIT(3),
2599 ASSOC_REQ_DISABLE_HE = BIT(4),
2600};
2601
2602/**
2603 * struct cfg80211_assoc_request - (Re)Association request data
2604 *
2605 * This structure provides information needed to complete IEEE 802.11
2606 * (re)association.
2607 * @bss: The BSS to associate with. If the call is successful the driver is
2608 * given a reference that it must give back to cfg80211_send_rx_assoc()
2609 * or to cfg80211_assoc_timeout(). To ensure proper refcounting, new
2610 * association requests while already associating must be rejected.
2611 * @ie: Extra IEs to add to (Re)Association Request frame or %NULL
2612 * @ie_len: Length of ie buffer in octets
2613 * @use_mfp: Use management frame protection (IEEE 802.11w) in this association
2614 * @crypto: crypto settings
2615 * @prev_bssid: previous BSSID, if not %NULL use reassociate frame. This is used
2616 * to indicate a request to reassociate within the ESS instead of a request
2617 * do the initial association with the ESS. When included, this is set to
2618 * the BSSID of the current association, i.e., to the value that is
2619 * included in the Current AP address field of the Reassociation Request
2620 * frame.
2621 * @flags: See &enum cfg80211_assoc_req_flags
2622 * @ht_capa: HT Capabilities over-rides. Values set in ht_capa_mask
2623 * will be used in ht_capa. Un-supported values will be ignored.
2624 * @ht_capa_mask: The bits of ht_capa which are to be used.
2625 * @vht_capa: VHT capability override
2626 * @vht_capa_mask: VHT capability mask indicating which fields to use
2627 * @fils_kek: FILS KEK for protecting (Re)Association Request/Response frame or
2628 * %NULL if FILS is not used.
2629 * @fils_kek_len: Length of fils_kek in octets
2630 * @fils_nonces: FILS nonces (part of AAD) for protecting (Re)Association
2631 * Request/Response frame or %NULL if FILS is not used. This field starts
2632 * with 16 octets of STA Nonce followed by 16 octets of AP Nonce.
2633 * @s1g_capa: S1G capability override
2634 * @s1g_capa_mask: S1G capability override mask
2635 */
2636struct cfg80211_assoc_request {
2637 struct cfg80211_bss *bss;
2638 const u8 *ie, *prev_bssid;
2639 size_t ie_len;
2640 struct cfg80211_crypto_settings crypto;
2641 bool use_mfp;
2642 u32 flags;
2643 struct ieee80211_ht_cap ht_capa;
2644 struct ieee80211_ht_cap ht_capa_mask;
2645 struct ieee80211_vht_cap vht_capa, vht_capa_mask;
2646 const u8 *fils_kek;
2647 size_t fils_kek_len;
2648 const u8 *fils_nonces;
2649 struct ieee80211_s1g_cap s1g_capa, s1g_capa_mask;
2650};
2651
2652/**
2653 * struct cfg80211_deauth_request - Deauthentication request data
2654 *
2655 * This structure provides information needed to complete IEEE 802.11
2656 * deauthentication.
2657 *
2658 * @bssid: the BSSID of the BSS to deauthenticate from
2659 * @ie: Extra IEs to add to Deauthentication frame or %NULL
2660 * @ie_len: Length of ie buffer in octets
2661 * @reason_code: The reason code for the deauthentication
2662 * @local_state_change: if set, change local state only and
2663 * do not set a deauth frame
2664 */
2665struct cfg80211_deauth_request {
2666 const u8 *bssid;
2667 const u8 *ie;
2668 size_t ie_len;
2669 u16 reason_code;
2670 bool local_state_change;
2671};
2672
2673/**
2674 * struct cfg80211_disassoc_request - Disassociation request data
2675 *
2676 * This structure provides information needed to complete IEEE 802.11
2677 * disassociation.
2678 *
2679 * @bss: the BSS to disassociate from
2680 * @ie: Extra IEs to add to Disassociation frame or %NULL
2681 * @ie_len: Length of ie buffer in octets
2682 * @reason_code: The reason code for the disassociation
2683 * @local_state_change: This is a request for a local state only, i.e., no
2684 * Disassociation frame is to be transmitted.
2685 */
2686struct cfg80211_disassoc_request {
2687 struct cfg80211_bss *bss;
2688 const u8 *ie;
2689 size_t ie_len;
2690 u16 reason_code;
2691 bool local_state_change;
2692};
2693
2694/**
2695 * struct cfg80211_ibss_params - IBSS parameters
2696 *
2697 * This structure defines the IBSS parameters for the join_ibss()
2698 * method.
2699 *
2700 * @ssid: The SSID, will always be non-null.
2701 * @ssid_len: The length of the SSID, will always be non-zero.
2702 * @bssid: Fixed BSSID requested, maybe be %NULL, if set do not
2703 * search for IBSSs with a different BSSID.
2704 * @chandef: defines the channel to use if no other IBSS to join can be found
2705 * @channel_fixed: The channel should be fixed -- do not search for
2706 * IBSSs to join on other channels.
2707 * @ie: information element(s) to include in the beacon
2708 * @ie_len: length of that
2709 * @beacon_interval: beacon interval to use
2710 * @privacy: this is a protected network, keys will be configured
2711 * after joining
2712 * @control_port: whether user space controls IEEE 802.1X port, i.e.,
2713 * sets/clears %NL80211_STA_FLAG_AUTHORIZED. If true, the driver is
2714 * required to assume that the port is unauthorized until authorized by
2715 * user space. Otherwise, port is marked authorized by default.
2716 * @control_port_over_nl80211: TRUE if userspace expects to exchange control
2717 * port frames over NL80211 instead of the network interface.
2718 * @userspace_handles_dfs: whether user space controls DFS operation, i.e.
2719 * changes the channel when a radar is detected. This is required
2720 * to operate on DFS channels.
2721 * @basic_rates: bitmap of basic rates to use when creating the IBSS
2722 * @mcast_rate: per-band multicast rate index + 1 (0: disabled)
2723 * @ht_capa: HT Capabilities over-rides. Values set in ht_capa_mask
2724 * will be used in ht_capa. Un-supported values will be ignored.
2725 * @ht_capa_mask: The bits of ht_capa which are to be used.
2726 * @wep_keys: static WEP keys, if not NULL points to an array of
2727 * CFG80211_MAX_WEP_KEYS WEP keys
2728 * @wep_tx_key: key index (0..3) of the default TX static WEP key
2729 */
2730struct cfg80211_ibss_params {
2731 const u8 *ssid;
2732 const u8 *bssid;
2733 struct cfg80211_chan_def chandef;
2734 const u8 *ie;
2735 u8 ssid_len, ie_len;
2736 u16 beacon_interval;
2737 u32 basic_rates;
2738 bool channel_fixed;
2739 bool privacy;
2740 bool control_port;
2741 bool control_port_over_nl80211;
2742 bool userspace_handles_dfs;
2743 int mcast_rate[NUM_NL80211_BANDS];
2744 struct ieee80211_ht_cap ht_capa;
2745 struct ieee80211_ht_cap ht_capa_mask;
2746 struct key_params *wep_keys;
2747 int wep_tx_key;
2748};
2749
2750/**
2751 * struct cfg80211_bss_selection - connection parameters for BSS selection.
2752 *
2753 * @behaviour: requested BSS selection behaviour.
2754 * @param: parameters for requestion behaviour.
2755 * @band_pref: preferred band for %NL80211_BSS_SELECT_ATTR_BAND_PREF.
2756 * @adjust: parameters for %NL80211_BSS_SELECT_ATTR_RSSI_ADJUST.
2757 */
2758struct cfg80211_bss_selection {
2759 enum nl80211_bss_select_attr behaviour;
2760 union {
2761 enum nl80211_band band_pref;
2762 struct cfg80211_bss_select_adjust adjust;
2763 } param;
2764};
2765
2766/**
2767 * struct cfg80211_connect_params - Connection parameters
2768 *
2769 * This structure provides information needed to complete IEEE 802.11
2770 * authentication and association.
2771 *
2772 * @channel: The channel to use or %NULL if not specified (auto-select based
2773 * on scan results)
2774 * @channel_hint: The channel of the recommended BSS for initial connection or
2775 * %NULL if not specified
2776 * @bssid: The AP BSSID or %NULL if not specified (auto-select based on scan
2777 * results)
2778 * @bssid_hint: The recommended AP BSSID for initial connection to the BSS or
2779 * %NULL if not specified. Unlike the @bssid parameter, the driver is
2780 * allowed to ignore this @bssid_hint if it has knowledge of a better BSS
2781 * to use.
2782 * @ssid: SSID
2783 * @ssid_len: Length of ssid in octets
2784 * @auth_type: Authentication type (algorithm)
2785 * @ie: IEs for association request
2786 * @ie_len: Length of assoc_ie in octets
2787 * @privacy: indicates whether privacy-enabled APs should be used
2788 * @mfp: indicate whether management frame protection is used
2789 * @crypto: crypto settings
2790 * @key_len: length of WEP key for shared key authentication
2791 * @key_idx: index of WEP key for shared key authentication
2792 * @key: WEP key for shared key authentication
2793 * @flags: See &enum cfg80211_assoc_req_flags
2794 * @bg_scan_period: Background scan period in seconds
2795 * or -1 to indicate that default value is to be used.
2796 * @ht_capa: HT Capabilities over-rides. Values set in ht_capa_mask
2797 * will be used in ht_capa. Un-supported values will be ignored.
2798 * @ht_capa_mask: The bits of ht_capa which are to be used.
2799 * @vht_capa: VHT Capability overrides
2800 * @vht_capa_mask: The bits of vht_capa which are to be used.
2801 * @pbss: if set, connect to a PCP instead of AP. Valid for DMG
2802 * networks.
2803 * @bss_select: criteria to be used for BSS selection.
2804 * @prev_bssid: previous BSSID, if not %NULL use reassociate frame. This is used
2805 * to indicate a request to reassociate within the ESS instead of a request
2806 * do the initial association with the ESS. When included, this is set to
2807 * the BSSID of the current association, i.e., to the value that is
2808 * included in the Current AP address field of the Reassociation Request
2809 * frame.
2810 * @fils_erp_username: EAP re-authentication protocol (ERP) username part of the
2811 * NAI or %NULL if not specified. This is used to construct FILS wrapped
2812 * data IE.
2813 * @fils_erp_username_len: Length of @fils_erp_username in octets.
2814 * @fils_erp_realm: EAP re-authentication protocol (ERP) realm part of NAI or
2815 * %NULL if not specified. This specifies the domain name of ER server and
2816 * is used to construct FILS wrapped data IE.
2817 * @fils_erp_realm_len: Length of @fils_erp_realm in octets.
2818 * @fils_erp_next_seq_num: The next sequence number to use in the FILS ERP
2819 * messages. This is also used to construct FILS wrapped data IE.
2820 * @fils_erp_rrk: ERP re-authentication Root Key (rRK) used to derive additional
2821 * keys in FILS or %NULL if not specified.
2822 * @fils_erp_rrk_len: Length of @fils_erp_rrk in octets.
2823 * @want_1x: indicates user-space supports and wants to use 802.1X driver
2824 * offload of 4-way handshake.
2825 * @edmg: define the EDMG channels.
2826 * This may specify multiple channels and bonding options for the driver
2827 * to choose from, based on BSS configuration.
2828 */
2829struct cfg80211_connect_params {
2830 struct ieee80211_channel *channel;
2831 struct ieee80211_channel *channel_hint;
2832 const u8 *bssid;
2833 const u8 *bssid_hint;
2834 const u8 *ssid;
2835 size_t ssid_len;
2836 enum nl80211_auth_type auth_type;
2837 const u8 *ie;
2838 size_t ie_len;
2839 bool privacy;
2840 enum nl80211_mfp mfp;
2841 struct cfg80211_crypto_settings crypto;
2842 const u8 *key;
2843 u8 key_len, key_idx;
2844 u32 flags;
2845 int bg_scan_period;
2846 struct ieee80211_ht_cap ht_capa;
2847 struct ieee80211_ht_cap ht_capa_mask;
2848 struct ieee80211_vht_cap vht_capa;
2849 struct ieee80211_vht_cap vht_capa_mask;
2850 bool pbss;
2851 struct cfg80211_bss_selection bss_select;
2852 const u8 *prev_bssid;
2853 const u8 *fils_erp_username;
2854 size_t fils_erp_username_len;
2855 const u8 *fils_erp_realm;
2856 size_t fils_erp_realm_len;
2857 u16 fils_erp_next_seq_num;
2858 const u8 *fils_erp_rrk;
2859 size_t fils_erp_rrk_len;
2860 bool want_1x;
2861 struct ieee80211_edmg edmg;
2862};
2863
2864/**
2865 * enum cfg80211_connect_params_changed - Connection parameters being updated
2866 *
2867 * This enum provides information of all connect parameters that
2868 * have to be updated as part of update_connect_params() call.
2869 *
2870 * @UPDATE_ASSOC_IES: Indicates whether association request IEs are updated
2871 * @UPDATE_FILS_ERP_INFO: Indicates that FILS connection parameters (realm,
2872 * username, erp sequence number and rrk) are updated
2873 * @UPDATE_AUTH_TYPE: Indicates that authentication type is updated
2874 */
2875enum cfg80211_connect_params_changed {
2876 UPDATE_ASSOC_IES = BIT(0),
2877 UPDATE_FILS_ERP_INFO = BIT(1),
2878 UPDATE_AUTH_TYPE = BIT(2),
2879};
2880
2881/**
2882 * enum wiphy_params_flags - set_wiphy_params bitfield values
2883 * @WIPHY_PARAM_RETRY_SHORT: wiphy->retry_short has changed
2884 * @WIPHY_PARAM_RETRY_LONG: wiphy->retry_long has changed
2885 * @WIPHY_PARAM_FRAG_THRESHOLD: wiphy->frag_threshold has changed
2886 * @WIPHY_PARAM_RTS_THRESHOLD: wiphy->rts_threshold has changed
2887 * @WIPHY_PARAM_COVERAGE_CLASS: coverage class changed
2888 * @WIPHY_PARAM_DYN_ACK: dynack has been enabled
2889 * @WIPHY_PARAM_TXQ_LIMIT: TXQ packet limit has been changed
2890 * @WIPHY_PARAM_TXQ_MEMORY_LIMIT: TXQ memory limit has been changed
2891 * @WIPHY_PARAM_TXQ_QUANTUM: TXQ scheduler quantum
2892 */
2893enum wiphy_params_flags {
2894 WIPHY_PARAM_RETRY_SHORT = 1 << 0,
2895 WIPHY_PARAM_RETRY_LONG = 1 << 1,
2896 WIPHY_PARAM_FRAG_THRESHOLD = 1 << 2,
2897 WIPHY_PARAM_RTS_THRESHOLD = 1 << 3,
2898 WIPHY_PARAM_COVERAGE_CLASS = 1 << 4,
2899 WIPHY_PARAM_DYN_ACK = 1 << 5,
2900 WIPHY_PARAM_TXQ_LIMIT = 1 << 6,
2901 WIPHY_PARAM_TXQ_MEMORY_LIMIT = 1 << 7,
2902 WIPHY_PARAM_TXQ_QUANTUM = 1 << 8,
2903};
2904
2905#define IEEE80211_DEFAULT_AIRTIME_WEIGHT 256
2906
2907/* The per TXQ device queue limit in airtime */
2908#define IEEE80211_DEFAULT_AQL_TXQ_LIMIT_L 5000
2909#define IEEE80211_DEFAULT_AQL_TXQ_LIMIT_H 12000
2910
2911/* The per interface airtime threshold to switch to lower queue limit */
2912#define IEEE80211_AQL_THRESHOLD 24000
2913
2914/**
2915 * struct cfg80211_pmksa - PMK Security Association
2916 *
2917 * This structure is passed to the set/del_pmksa() method for PMKSA
2918 * caching.
2919 *
2920 * @bssid: The AP's BSSID (may be %NULL).
2921 * @pmkid: The identifier to refer a PMKSA.
2922 * @pmk: The PMK for the PMKSA identified by @pmkid. This is used for key
2923 * derivation by a FILS STA. Otherwise, %NULL.
2924 * @pmk_len: Length of the @pmk. The length of @pmk can differ depending on
2925 * the hash algorithm used to generate this.
2926 * @ssid: SSID to specify the ESS within which a PMKSA is valid when using FILS
2927 * cache identifier (may be %NULL).
2928 * @ssid_len: Length of the @ssid in octets.
2929 * @cache_id: 2-octet cache identifier advertized by a FILS AP identifying the
2930 * scope of PMKSA. This is valid only if @ssid_len is non-zero (may be
2931 * %NULL).
2932 * @pmk_lifetime: Maximum lifetime for PMKSA in seconds
2933 * (dot11RSNAConfigPMKLifetime) or 0 if not specified.
2934 * The configured PMKSA must not be used for PMKSA caching after
2935 * expiration and any keys derived from this PMK become invalid on
2936 * expiration, i.e., the current association must be dropped if the PMK
2937 * used for it expires.
2938 * @pmk_reauth_threshold: Threshold time for reauthentication (percentage of
2939 * PMK lifetime, dot11RSNAConfigPMKReauthThreshold) or 0 if not specified.
2940 * Drivers are expected to trigger a full authentication instead of using
2941 * this PMKSA for caching when reassociating to a new BSS after this
2942 * threshold to generate a new PMK before the current one expires.
2943 */
2944struct cfg80211_pmksa {
2945 const u8 *bssid;
2946 const u8 *pmkid;
2947 const u8 *pmk;
2948 size_t pmk_len;
2949 const u8 *ssid;
2950 size_t ssid_len;
2951 const u8 *cache_id;
2952 u32 pmk_lifetime;
2953 u8 pmk_reauth_threshold;
2954};
2955
2956/**
2957 * struct cfg80211_pkt_pattern - packet pattern
2958 * @mask: bitmask where to match pattern and where to ignore bytes,
2959 * one bit per byte, in same format as nl80211
2960 * @pattern: bytes to match where bitmask is 1
2961 * @pattern_len: length of pattern (in bytes)
2962 * @pkt_offset: packet offset (in bytes)
2963 *
2964 * Internal note: @mask and @pattern are allocated in one chunk of
2965 * memory, free @mask only!
2966 */
2967struct cfg80211_pkt_pattern {
2968 const u8 *mask, *pattern;
2969 int pattern_len;
2970 int pkt_offset;
2971};
2972
2973/**
2974 * struct cfg80211_wowlan_tcp - TCP connection parameters
2975 *
2976 * @sock: (internal) socket for source port allocation
2977 * @src: source IP address
2978 * @dst: destination IP address
2979 * @dst_mac: destination MAC address
2980 * @src_port: source port
2981 * @dst_port: destination port
2982 * @payload_len: data payload length
2983 * @payload: data payload buffer
2984 * @payload_seq: payload sequence stamping configuration
2985 * @data_interval: interval at which to send data packets
2986 * @wake_len: wakeup payload match length
2987 * @wake_data: wakeup payload match data
2988 * @wake_mask: wakeup payload match mask
2989 * @tokens_size: length of the tokens buffer
2990 * @payload_tok: payload token usage configuration
2991 */
2992struct cfg80211_wowlan_tcp {
2993 struct socket *sock;
2994 __be32 src, dst;
2995 u16 src_port, dst_port;
2996 u8 dst_mac[ETH_ALEN];
2997 int payload_len;
2998 const u8 *payload;
2999 struct nl80211_wowlan_tcp_data_seq payload_seq;
3000 u32 data_interval;
3001 u32 wake_len;
3002 const u8 *wake_data, *wake_mask;
3003 u32 tokens_size;
3004 /* must be last, variable member */
3005 struct nl80211_wowlan_tcp_data_token payload_tok;
3006};
3007
3008/**
3009 * struct cfg80211_wowlan - Wake on Wireless-LAN support info
3010 *
3011 * This structure defines the enabled WoWLAN triggers for the device.
3012 * @any: wake up on any activity -- special trigger if device continues
3013 * operating as normal during suspend
3014 * @disconnect: wake up if getting disconnected
3015 * @magic_pkt: wake up on receiving magic packet
3016 * @patterns: wake up on receiving packet matching a pattern
3017 * @n_patterns: number of patterns
3018 * @gtk_rekey_failure: wake up on GTK rekey failure
3019 * @eap_identity_req: wake up on EAP identity request packet
3020 * @four_way_handshake: wake up on 4-way handshake
3021 * @rfkill_release: wake up when rfkill is released
3022 * @tcp: TCP connection establishment/wakeup parameters, see nl80211.h.
3023 * NULL if not configured.
3024 * @nd_config: configuration for the scan to be used for net detect wake.
3025 */
3026struct cfg80211_wowlan {
3027 bool any, disconnect, magic_pkt, gtk_rekey_failure,
3028 eap_identity_req, four_way_handshake,
3029 rfkill_release;
3030 struct cfg80211_pkt_pattern *patterns;
3031 struct cfg80211_wowlan_tcp *tcp;
3032 int n_patterns;
3033 struct cfg80211_sched_scan_request *nd_config;
3034};
3035
3036/**
3037 * struct cfg80211_coalesce_rules - Coalesce rule parameters
3038 *
3039 * This structure defines coalesce rule for the device.
3040 * @delay: maximum coalescing delay in msecs.
3041 * @condition: condition for packet coalescence.
3042 * see &enum nl80211_coalesce_condition.
3043 * @patterns: array of packet patterns
3044 * @n_patterns: number of patterns
3045 */
3046struct cfg80211_coalesce_rules {
3047 int delay;
3048 enum nl80211_coalesce_condition condition;
3049 struct cfg80211_pkt_pattern *patterns;
3050 int n_patterns;
3051};
3052
3053/**
3054 * struct cfg80211_coalesce - Packet coalescing settings
3055 *
3056 * This structure defines coalescing settings.
3057 * @rules: array of coalesce rules
3058 * @n_rules: number of rules
3059 */
3060struct cfg80211_coalesce {
3061 struct cfg80211_coalesce_rules *rules;
3062 int n_rules;
3063};
3064
3065/**
3066 * struct cfg80211_wowlan_nd_match - information about the match
3067 *
3068 * @ssid: SSID of the match that triggered the wake up
3069 * @n_channels: Number of channels where the match occurred. This
3070 * value may be zero if the driver can't report the channels.
3071 * @channels: center frequencies of the channels where a match
3072 * occurred (in MHz)
3073 */
3074struct cfg80211_wowlan_nd_match {
3075 struct cfg80211_ssid ssid;
3076 int n_channels;
3077 u32 channels[];
3078};
3079
3080/**
3081 * struct cfg80211_wowlan_nd_info - net detect wake up information
3082 *
3083 * @n_matches: Number of match information instances provided in
3084 * @matches. This value may be zero if the driver can't provide
3085 * match information.
3086 * @matches: Array of pointers to matches containing information about
3087 * the matches that triggered the wake up.
3088 */
3089struct cfg80211_wowlan_nd_info {
3090 int n_matches;
3091 struct cfg80211_wowlan_nd_match *matches[];
3092};
3093
3094/**
3095 * struct cfg80211_wowlan_wakeup - wakeup report
3096 * @disconnect: woke up by getting disconnected
3097 * @magic_pkt: woke up by receiving magic packet
3098 * @gtk_rekey_failure: woke up by GTK rekey failure
3099 * @eap_identity_req: woke up by EAP identity request packet
3100 * @four_way_handshake: woke up by 4-way handshake
3101 * @rfkill_release: woke up by rfkill being released
3102 * @pattern_idx: pattern that caused wakeup, -1 if not due to pattern
3103 * @packet_present_len: copied wakeup packet data
3104 * @packet_len: original wakeup packet length
3105 * @packet: The packet causing the wakeup, if any.
3106 * @packet_80211: For pattern match, magic packet and other data
3107 * frame triggers an 802.3 frame should be reported, for
3108 * disconnect due to deauth 802.11 frame. This indicates which
3109 * it is.
3110 * @tcp_match: TCP wakeup packet received
3111 * @tcp_connlost: TCP connection lost or failed to establish
3112 * @tcp_nomoretokens: TCP data ran out of tokens
3113 * @net_detect: if not %NULL, woke up because of net detect
3114 */
3115struct cfg80211_wowlan_wakeup {
3116 bool disconnect, magic_pkt, gtk_rekey_failure,
3117 eap_identity_req, four_way_handshake,
3118 rfkill_release, packet_80211,
3119 tcp_match, tcp_connlost, tcp_nomoretokens;
3120 s32 pattern_idx;
3121 u32 packet_present_len, packet_len;
3122 const void *packet;
3123 struct cfg80211_wowlan_nd_info *net_detect;
3124};
3125
3126/**
3127 * struct cfg80211_gtk_rekey_data - rekey data
3128 * @kek: key encryption key (@kek_len bytes)
3129 * @kck: key confirmation key (@kck_len bytes)
3130 * @replay_ctr: replay counter (NL80211_REPLAY_CTR_LEN bytes)
3131 * @kek_len: length of kek
3132 * @kck_len length of kck
3133 * @akm: akm (oui, id)
3134 */
3135struct cfg80211_gtk_rekey_data {
3136 const u8 *kek, *kck, *replay_ctr;
3137 u32 akm;
3138 u8 kek_len, kck_len;
3139};
3140
3141/**
3142 * struct cfg80211_update_ft_ies_params - FT IE Information
3143 *
3144 * This structure provides information needed to update the fast transition IE
3145 *
3146 * @md: The Mobility Domain ID, 2 Octet value
3147 * @ie: Fast Transition IEs
3148 * @ie_len: Length of ft_ie in octets
3149 */
3150struct cfg80211_update_ft_ies_params {
3151 u16 md;
3152 const u8 *ie;
3153 size_t ie_len;
3154};
3155
3156/**
3157 * struct cfg80211_mgmt_tx_params - mgmt tx parameters
3158 *
3159 * This structure provides information needed to transmit a mgmt frame
3160 *
3161 * @chan: channel to use
3162 * @offchan: indicates wether off channel operation is required
3163 * @wait: duration for ROC
3164 * @buf: buffer to transmit
3165 * @len: buffer length
3166 * @no_cck: don't use cck rates for this frame
3167 * @dont_wait_for_ack: tells the low level not to wait for an ack
3168 * @n_csa_offsets: length of csa_offsets array
3169 * @csa_offsets: array of all the csa offsets in the frame
3170 */
3171struct cfg80211_mgmt_tx_params {
3172 struct ieee80211_channel *chan;
3173 bool offchan;
3174 unsigned int wait;
3175 const u8 *buf;
3176 size_t len;
3177 bool no_cck;
3178 bool dont_wait_for_ack;
3179 int n_csa_offsets;
3180 const u16 *csa_offsets;
3181};
3182
3183/**
3184 * struct cfg80211_dscp_exception - DSCP exception
3185 *
3186 * @dscp: DSCP value that does not adhere to the user priority range definition
3187 * @up: user priority value to which the corresponding DSCP value belongs
3188 */
3189struct cfg80211_dscp_exception {
3190 u8 dscp;
3191 u8 up;
3192};
3193
3194/**
3195 * struct cfg80211_dscp_range - DSCP range definition for user priority
3196 *
3197 * @low: lowest DSCP value of this user priority range, inclusive
3198 * @high: highest DSCP value of this user priority range, inclusive
3199 */
3200struct cfg80211_dscp_range {
3201 u8 low;
3202 u8 high;
3203};
3204
3205/* QoS Map Set element length defined in IEEE Std 802.11-2012, 8.4.2.97 */
3206#define IEEE80211_QOS_MAP_MAX_EX 21
3207#define IEEE80211_QOS_MAP_LEN_MIN 16
3208#define IEEE80211_QOS_MAP_LEN_MAX \
3209 (IEEE80211_QOS_MAP_LEN_MIN + 2 * IEEE80211_QOS_MAP_MAX_EX)
3210
3211/**
3212 * struct cfg80211_qos_map - QoS Map Information
3213 *
3214 * This struct defines the Interworking QoS map setting for DSCP values
3215 *
3216 * @num_des: number of DSCP exceptions (0..21)
3217 * @dscp_exception: optionally up to maximum of 21 DSCP exceptions from
3218 * the user priority DSCP range definition
3219 * @up: DSCP range definition for a particular user priority
3220 */
3221struct cfg80211_qos_map {
3222 u8 num_des;
3223 struct cfg80211_dscp_exception dscp_exception[IEEE80211_QOS_MAP_MAX_EX];
3224 struct cfg80211_dscp_range up[8];
3225};
3226
3227/**
3228 * struct cfg80211_nan_conf - NAN configuration
3229 *
3230 * This struct defines NAN configuration parameters
3231 *
3232 * @master_pref: master preference (1 - 255)
3233 * @bands: operating bands, a bitmap of &enum nl80211_band values.
3234 * For instance, for NL80211_BAND_2GHZ, bit 0 would be set
3235 * (i.e. BIT(NL80211_BAND_2GHZ)).
3236 */
3237struct cfg80211_nan_conf {
3238 u8 master_pref;
3239 u8 bands;
3240};
3241
3242/**
3243 * enum cfg80211_nan_conf_changes - indicates changed fields in NAN
3244 * configuration
3245 *
3246 * @CFG80211_NAN_CONF_CHANGED_PREF: master preference
3247 * @CFG80211_NAN_CONF_CHANGED_BANDS: operating bands
3248 */
3249enum cfg80211_nan_conf_changes {
3250 CFG80211_NAN_CONF_CHANGED_PREF = BIT(0),
3251 CFG80211_NAN_CONF_CHANGED_BANDS = BIT(1),
3252};
3253
3254/**
3255 * struct cfg80211_nan_func_filter - a NAN function Rx / Tx filter
3256 *
3257 * @filter: the content of the filter
3258 * @len: the length of the filter
3259 */
3260struct cfg80211_nan_func_filter {
3261 const u8 *filter;
3262 u8 len;
3263};
3264
3265/**
3266 * struct cfg80211_nan_func - a NAN function
3267 *
3268 * @type: &enum nl80211_nan_function_type
3269 * @service_id: the service ID of the function
3270 * @publish_type: &nl80211_nan_publish_type
3271 * @close_range: if true, the range should be limited. Threshold is
3272 * implementation specific.
3273 * @publish_bcast: if true, the solicited publish should be broadcasted
3274 * @subscribe_active: if true, the subscribe is active
3275 * @followup_id: the instance ID for follow up
3276 * @followup_reqid: the requestor instance ID for follow up
3277 * @followup_dest: MAC address of the recipient of the follow up
3278 * @ttl: time to live counter in DW.
3279 * @serv_spec_info: Service Specific Info
3280 * @serv_spec_info_len: Service Specific Info length
3281 * @srf_include: if true, SRF is inclusive
3282 * @srf_bf: Bloom Filter
3283 * @srf_bf_len: Bloom Filter length
3284 * @srf_bf_idx: Bloom Filter index
3285 * @srf_macs: SRF MAC addresses
3286 * @srf_num_macs: number of MAC addresses in SRF
3287 * @rx_filters: rx filters that are matched with corresponding peer's tx_filter
3288 * @tx_filters: filters that should be transmitted in the SDF.
3289 * @num_rx_filters: length of &rx_filters.
3290 * @num_tx_filters: length of &tx_filters.
3291 * @instance_id: driver allocated id of the function.
3292 * @cookie: unique NAN function identifier.
3293 */
3294struct cfg80211_nan_func {
3295 enum nl80211_nan_function_type type;
3296 u8 service_id[NL80211_NAN_FUNC_SERVICE_ID_LEN];
3297 u8 publish_type;
3298 bool close_range;
3299 bool publish_bcast;
3300 bool subscribe_active;
3301 u8 followup_id;
3302 u8 followup_reqid;
3303 struct mac_address followup_dest;
3304 u32 ttl;
3305 const u8 *serv_spec_info;
3306 u8 serv_spec_info_len;
3307 bool srf_include;
3308 const u8 *srf_bf;
3309 u8 srf_bf_len;
3310 u8 srf_bf_idx;
3311 struct mac_address *srf_macs;
3312 int srf_num_macs;
3313 struct cfg80211_nan_func_filter *rx_filters;
3314 struct cfg80211_nan_func_filter *tx_filters;
3315 u8 num_tx_filters;
3316 u8 num_rx_filters;
3317 u8 instance_id;
3318 u64 cookie;
3319};
3320
3321/**
3322 * struct cfg80211_pmk_conf - PMK configuration
3323 *
3324 * @aa: authenticator address
3325 * @pmk_len: PMK length in bytes.
3326 * @pmk: the PMK material
3327 * @pmk_r0_name: PMK-R0 Name. NULL if not applicable (i.e., the PMK
3328 * is not PMK-R0). When pmk_r0_name is not NULL, the pmk field
3329 * holds PMK-R0.
3330 */
3331struct cfg80211_pmk_conf {
3332 const u8 *aa;
3333 u8 pmk_len;
3334 const u8 *pmk;
3335 const u8 *pmk_r0_name;
3336};
3337
3338/**
3339 * struct cfg80211_external_auth_params - Trigger External authentication.
3340 *
3341 * Commonly used across the external auth request and event interfaces.
3342 *
3343 * @action: action type / trigger for external authentication. Only significant
3344 * for the authentication request event interface (driver to user space).
3345 * @bssid: BSSID of the peer with which the authentication has
3346 * to happen. Used by both the authentication request event and
3347 * authentication response command interface.
3348 * @ssid: SSID of the AP. Used by both the authentication request event and
3349 * authentication response command interface.
3350 * @key_mgmt_suite: AKM suite of the respective authentication. Used by the
3351 * authentication request event interface.
3352 * @status: status code, %WLAN_STATUS_SUCCESS for successful authentication,
3353 * use %WLAN_STATUS_UNSPECIFIED_FAILURE if user space cannot give you
3354 * the real status code for failures. Used only for the authentication
3355 * response command interface (user space to driver).
3356 * @pmkid: The identifier to refer a PMKSA.
3357 */
3358struct cfg80211_external_auth_params {
3359 enum nl80211_external_auth_action action;
3360 u8 bssid[ETH_ALEN] __aligned(2);
3361 struct cfg80211_ssid ssid;
3362 unsigned int key_mgmt_suite;
3363 u16 status;
3364 const u8 *pmkid;
3365};
3366
3367/**
3368 * struct cfg80211_ftm_responder_stats - FTM responder statistics
3369 *
3370 * @filled: bitflag of flags using the bits of &enum nl80211_ftm_stats to
3371 * indicate the relevant values in this struct for them
3372 * @success_num: number of FTM sessions in which all frames were successfully
3373 * answered
3374 * @partial_num: number of FTM sessions in which part of frames were
3375 * successfully answered
3376 * @failed_num: number of failed FTM sessions
3377 * @asap_num: number of ASAP FTM sessions
3378 * @non_asap_num: number of non-ASAP FTM sessions
3379 * @total_duration_ms: total sessions durations - gives an indication
3380 * of how much time the responder was busy
3381 * @unknown_triggers_num: number of unknown FTM triggers - triggers from
3382 * initiators that didn't finish successfully the negotiation phase with
3383 * the responder
3384 * @reschedule_requests_num: number of FTM reschedule requests - initiator asks
3385 * for a new scheduling although it already has scheduled FTM slot
3386 * @out_of_window_triggers_num: total FTM triggers out of scheduled window
3387 */
3388struct cfg80211_ftm_responder_stats {
3389 u32 filled;
3390 u32 success_num;
3391 u32 partial_num;
3392 u32 failed_num;
3393 u32 asap_num;
3394 u32 non_asap_num;
3395 u64 total_duration_ms;
3396 u32 unknown_triggers_num;
3397 u32 reschedule_requests_num;
3398 u32 out_of_window_triggers_num;
3399};
3400
3401/**
3402 * struct cfg80211_pmsr_ftm_result - FTM result
3403 * @failure_reason: if this measurement failed (PMSR status is
3404 * %NL80211_PMSR_STATUS_FAILURE), this gives a more precise
3405 * reason than just "failure"
3406 * @burst_index: if reporting partial results, this is the index
3407 * in [0 .. num_bursts-1] of the burst that's being reported
3408 * @num_ftmr_attempts: number of FTM request frames transmitted
3409 * @num_ftmr_successes: number of FTM request frames acked
3410 * @busy_retry_time: if failure_reason is %NL80211_PMSR_FTM_FAILURE_PEER_BUSY,
3411 * fill this to indicate in how many seconds a retry is deemed possible
3412 * by the responder
3413 * @num_bursts_exp: actual number of bursts exponent negotiated
3414 * @burst_duration: actual burst duration negotiated
3415 * @ftms_per_burst: actual FTMs per burst negotiated
3416 * @lci_len: length of LCI information (if present)
3417 * @civicloc_len: length of civic location information (if present)
3418 * @lci: LCI data (may be %NULL)
3419 * @civicloc: civic location data (may be %NULL)
3420 * @rssi_avg: average RSSI over FTM action frames reported
3421 * @rssi_spread: spread of the RSSI over FTM action frames reported
3422 * @tx_rate: bitrate for transmitted FTM action frame response
3423 * @rx_rate: bitrate of received FTM action frame
3424 * @rtt_avg: average of RTTs measured (must have either this or @dist_avg)
3425 * @rtt_variance: variance of RTTs measured (note that standard deviation is
3426 * the square root of the variance)
3427 * @rtt_spread: spread of the RTTs measured
3428 * @dist_avg: average of distances (mm) measured
3429 * (must have either this or @rtt_avg)
3430 * @dist_variance: variance of distances measured (see also @rtt_variance)
3431 * @dist_spread: spread of distances measured (see also @rtt_spread)
3432 * @num_ftmr_attempts_valid: @num_ftmr_attempts is valid
3433 * @num_ftmr_successes_valid: @num_ftmr_successes is valid
3434 * @rssi_avg_valid: @rssi_avg is valid
3435 * @rssi_spread_valid: @rssi_spread is valid
3436 * @tx_rate_valid: @tx_rate is valid
3437 * @rx_rate_valid: @rx_rate is valid
3438 * @rtt_avg_valid: @rtt_avg is valid
3439 * @rtt_variance_valid: @rtt_variance is valid
3440 * @rtt_spread_valid: @rtt_spread is valid
3441 * @dist_avg_valid: @dist_avg is valid
3442 * @dist_variance_valid: @dist_variance is valid
3443 * @dist_spread_valid: @dist_spread is valid
3444 */
3445struct cfg80211_pmsr_ftm_result {
3446 const u8 *lci;
3447 const u8 *civicloc;
3448 unsigned int lci_len;
3449 unsigned int civicloc_len;
3450 enum nl80211_peer_measurement_ftm_failure_reasons failure_reason;
3451 u32 num_ftmr_attempts, num_ftmr_successes;
3452 s16 burst_index;
3453 u8 busy_retry_time;
3454 u8 num_bursts_exp;
3455 u8 burst_duration;
3456 u8 ftms_per_burst;
3457 s32 rssi_avg;
3458 s32 rssi_spread;
3459 struct rate_info tx_rate, rx_rate;
3460 s64 rtt_avg;
3461 s64 rtt_variance;
3462 s64 rtt_spread;
3463 s64 dist_avg;
3464 s64 dist_variance;
3465 s64 dist_spread;
3466
3467 u16 num_ftmr_attempts_valid:1,
3468 num_ftmr_successes_valid:1,
3469 rssi_avg_valid:1,
3470 rssi_spread_valid:1,
3471 tx_rate_valid:1,
3472 rx_rate_valid:1,
3473 rtt_avg_valid:1,
3474 rtt_variance_valid:1,
3475 rtt_spread_valid:1,
3476 dist_avg_valid:1,
3477 dist_variance_valid:1,
3478 dist_spread_valid:1;
3479};
3480
3481/**
3482 * struct cfg80211_pmsr_result - peer measurement result
3483 * @addr: address of the peer
3484 * @host_time: host time (use ktime_get_boottime() adjust to the time when the
3485 * measurement was made)
3486 * @ap_tsf: AP's TSF at measurement time
3487 * @status: status of the measurement
3488 * @final: if reporting partial results, mark this as the last one; if not
3489 * reporting partial results always set this flag
3490 * @ap_tsf_valid: indicates the @ap_tsf value is valid
3491 * @type: type of the measurement reported, note that we only support reporting
3492 * one type at a time, but you can report multiple results separately and
3493 * they're all aggregated for userspace.
3494 */
3495struct cfg80211_pmsr_result {
3496 u64 host_time, ap_tsf;
3497 enum nl80211_peer_measurement_status status;
3498
3499 u8 addr[ETH_ALEN];
3500
3501 u8 final:1,
3502 ap_tsf_valid:1;
3503
3504 enum nl80211_peer_measurement_type type;
3505
3506 union {
3507 struct cfg80211_pmsr_ftm_result ftm;
3508 };
3509};
3510
3511/**
3512 * struct cfg80211_pmsr_ftm_request_peer - FTM request data
3513 * @requested: indicates FTM is requested
3514 * @preamble: frame preamble to use
3515 * @burst_period: burst period to use
3516 * @asap: indicates to use ASAP mode
3517 * @num_bursts_exp: number of bursts exponent
3518 * @burst_duration: burst duration
3519 * @ftms_per_burst: number of FTMs per burst
3520 * @ftmr_retries: number of retries for FTM request
3521 * @request_lci: request LCI information
3522 * @request_civicloc: request civic location information
3523 * @trigger_based: use trigger based ranging for the measurement
3524 * If neither @trigger_based nor @non_trigger_based is set,
3525 * EDCA based ranging will be used.
3526 * @non_trigger_based: use non trigger based ranging for the measurement
3527 * If neither @trigger_based nor @non_trigger_based is set,
3528 * EDCA based ranging will be used.
3529 * @lmr_feedback: negotiate for I2R LMR feedback. Only valid if either
3530 * @trigger_based or @non_trigger_based is set.
3531 * @bss_color: the bss color of the responder. Optional. Set to zero to
3532 * indicate the driver should set the BSS color. Only valid if
3533 * @non_trigger_based or @trigger_based is set.
3534 *
3535 * See also nl80211 for the respective attribute documentation.
3536 */
3537struct cfg80211_pmsr_ftm_request_peer {
3538 enum nl80211_preamble preamble;
3539 u16 burst_period;
3540 u8 requested:1,
3541 asap:1,
3542 request_lci:1,
3543 request_civicloc:1,
3544 trigger_based:1,
3545 non_trigger_based:1,
3546 lmr_feedback:1;
3547 u8 num_bursts_exp;
3548 u8 burst_duration;
3549 u8 ftms_per_burst;
3550 u8 ftmr_retries;
3551 u8 bss_color;
3552};
3553
3554/**
3555 * struct cfg80211_pmsr_request_peer - peer data for a peer measurement request
3556 * @addr: MAC address
3557 * @chandef: channel to use
3558 * @report_ap_tsf: report the associated AP's TSF
3559 * @ftm: FTM data, see &struct cfg80211_pmsr_ftm_request_peer
3560 */
3561struct cfg80211_pmsr_request_peer {
3562 u8 addr[ETH_ALEN];
3563 struct cfg80211_chan_def chandef;
3564 u8 report_ap_tsf:1;
3565 struct cfg80211_pmsr_ftm_request_peer ftm;
3566};
3567
3568/**
3569 * struct cfg80211_pmsr_request - peer measurement request
3570 * @cookie: cookie, set by cfg80211
3571 * @nl_portid: netlink portid - used by cfg80211
3572 * @drv_data: driver data for this request, if required for aborting,
3573 * not otherwise freed or anything by cfg80211
3574 * @mac_addr: MAC address used for (randomised) request
3575 * @mac_addr_mask: MAC address mask used for randomisation, bits that
3576 * are 0 in the mask should be randomised, bits that are 1 should
3577 * be taken from the @mac_addr
3578 * @list: used by cfg80211 to hold on to the request
3579 * @timeout: timeout (in milliseconds) for the whole operation, if
3580 * zero it means there's no timeout
3581 * @n_peers: number of peers to do measurements with
3582 * @peers: per-peer measurement request data
3583 */
3584struct cfg80211_pmsr_request {
3585 u64 cookie;
3586 void *drv_data;
3587 u32 n_peers;
3588 u32 nl_portid;
3589
3590 u32 timeout;
3591
3592 u8 mac_addr[ETH_ALEN] __aligned(2);
3593 u8 mac_addr_mask[ETH_ALEN] __aligned(2);
3594
3595 struct list_head list;
3596
3597 struct cfg80211_pmsr_request_peer peers[];
3598};
3599
3600/**
3601 * struct cfg80211_update_owe_info - OWE Information
3602 *
3603 * This structure provides information needed for the drivers to offload OWE
3604 * (Opportunistic Wireless Encryption) processing to the user space.
3605 *
3606 * Commonly used across update_owe_info request and event interfaces.
3607 *
3608 * @peer: MAC address of the peer device for which the OWE processing
3609 * has to be done.
3610 * @status: status code, %WLAN_STATUS_SUCCESS for successful OWE info
3611 * processing, use %WLAN_STATUS_UNSPECIFIED_FAILURE if user space
3612 * cannot give you the real status code for failures. Used only for
3613 * OWE update request command interface (user space to driver).
3614 * @ie: IEs obtained from the peer or constructed by the user space. These are
3615 * the IEs of the remote peer in the event from the host driver and
3616 * the constructed IEs by the user space in the request interface.
3617 * @ie_len: Length of IEs in octets.
3618 */
3619struct cfg80211_update_owe_info {
3620 u8 peer[ETH_ALEN] __aligned(2);
3621 u16 status;
3622 const u8 *ie;
3623 size_t ie_len;
3624};
3625
3626/**
3627 * struct mgmt_frame_regs - management frame registrations data
3628 * @global_stypes: bitmap of management frame subtypes registered
3629 * for the entire device
3630 * @interface_stypes: bitmap of management frame subtypes registered
3631 * for the given interface
3632 * @global_mcast_rx: mcast RX is needed globally for these subtypes
3633 * @interface_mcast_stypes: mcast RX is needed on this interface
3634 * for these subtypes
3635 */
3636struct mgmt_frame_regs {
3637 u32 global_stypes, interface_stypes;
3638 u32 global_mcast_stypes, interface_mcast_stypes;
3639};
3640
3641/**
3642 * struct cfg80211_ops - backend description for wireless configuration
3643 *
3644 * This struct is registered by fullmac card drivers and/or wireless stacks
3645 * in order to handle configuration requests on their interfaces.
3646 *
3647 * All callbacks except where otherwise noted should return 0
3648 * on success or a negative error code.
3649 *
3650 * All operations are invoked with the wiphy mutex held. The RTNL may be
3651 * held in addition (due to wireless extensions) but this cannot be relied
3652 * upon except in cases where documented below. Note that due to ordering,
3653 * the RTNL also cannot be acquired in any handlers.
3654 *
3655 * @suspend: wiphy device needs to be suspended. The variable @wow will
3656 * be %NULL or contain the enabled Wake-on-Wireless triggers that are
3657 * configured for the device.
3658 * @resume: wiphy device needs to be resumed
3659 * @set_wakeup: Called when WoWLAN is enabled/disabled, use this callback
3660 * to call device_set_wakeup_enable() to enable/disable wakeup from
3661 * the device.
3662 *
3663 * @add_virtual_intf: create a new virtual interface with the given name,
3664 * must set the struct wireless_dev's iftype. Beware: You must create
3665 * the new netdev in the wiphy's network namespace! Returns the struct
3666 * wireless_dev, or an ERR_PTR. For P2P device wdevs, the driver must
3667 * also set the address member in the wdev.
3668 * This additionally holds the RTNL to be able to do netdev changes.
3669 *
3670 * @del_virtual_intf: remove the virtual interface
3671 * This additionally holds the RTNL to be able to do netdev changes.
3672 *
3673 * @change_virtual_intf: change type/configuration of virtual interface,
3674 * keep the struct wireless_dev's iftype updated.
3675 * This additionally holds the RTNL to be able to do netdev changes.
3676 *
3677 * @add_key: add a key with the given parameters. @mac_addr will be %NULL
3678 * when adding a group key.
3679 *
3680 * @get_key: get information about the key with the given parameters.
3681 * @mac_addr will be %NULL when requesting information for a group
3682 * key. All pointers given to the @callback function need not be valid
3683 * after it returns. This function should return an error if it is
3684 * not possible to retrieve the key, -ENOENT if it doesn't exist.
3685 *
3686 * @del_key: remove a key given the @mac_addr (%NULL for a group key)
3687 * and @key_index, return -ENOENT if the key doesn't exist.
3688 *
3689 * @set_default_key: set the default key on an interface
3690 *
3691 * @set_default_mgmt_key: set the default management frame key on an interface
3692 *
3693 * @set_default_beacon_key: set the default Beacon frame key on an interface
3694 *
3695 * @set_rekey_data: give the data necessary for GTK rekeying to the driver
3696 *
3697 * @start_ap: Start acting in AP mode defined by the parameters.
3698 * @change_beacon: Change the beacon parameters for an access point mode
3699 * interface. This should reject the call when AP mode wasn't started.
3700 * @stop_ap: Stop being an AP, including stopping beaconing.
3701 *
3702 * @add_station: Add a new station.
3703 * @del_station: Remove a station
3704 * @change_station: Modify a given station. Note that flags changes are not much
3705 * validated in cfg80211, in particular the auth/assoc/authorized flags
3706 * might come to the driver in invalid combinations -- make sure to check
3707 * them, also against the existing state! Drivers must call
3708 * cfg80211_check_station_change() to validate the information.
3709 * @get_station: get station information for the station identified by @mac
3710 * @dump_station: dump station callback -- resume dump at index @idx
3711 *
3712 * @add_mpath: add a fixed mesh path
3713 * @del_mpath: delete a given mesh path
3714 * @change_mpath: change a given mesh path
3715 * @get_mpath: get a mesh path for the given parameters
3716 * @dump_mpath: dump mesh path callback -- resume dump at index @idx
3717 * @get_mpp: get a mesh proxy path for the given parameters
3718 * @dump_mpp: dump mesh proxy path callback -- resume dump at index @idx
3719 * @join_mesh: join the mesh network with the specified parameters
3720 * (invoked with the wireless_dev mutex held)
3721 * @leave_mesh: leave the current mesh network
3722 * (invoked with the wireless_dev mutex held)
3723 *
3724 * @get_mesh_config: Get the current mesh configuration
3725 *
3726 * @update_mesh_config: Update mesh parameters on a running mesh.
3727 * The mask is a bitfield which tells us which parameters to
3728 * set, and which to leave alone.
3729 *
3730 * @change_bss: Modify parameters for a given BSS.
3731 *
3732 * @set_txq_params: Set TX queue parameters
3733 *
3734 * @libertas_set_mesh_channel: Only for backward compatibility for libertas,
3735 * as it doesn't implement join_mesh and needs to set the channel to
3736 * join the mesh instead.
3737 *
3738 * @set_monitor_channel: Set the monitor mode channel for the device. If other
3739 * interfaces are active this callback should reject the configuration.
3740 * If no interfaces are active or the device is down, the channel should
3741 * be stored for when a monitor interface becomes active.
3742 *
3743 * @scan: Request to do a scan. If returning zero, the scan request is given
3744 * the driver, and will be valid until passed to cfg80211_scan_done().
3745 * For scan results, call cfg80211_inform_bss(); you can call this outside
3746 * the scan/scan_done bracket too.
3747 * @abort_scan: Tell the driver to abort an ongoing scan. The driver shall
3748 * indicate the status of the scan through cfg80211_scan_done().
3749 *
3750 * @auth: Request to authenticate with the specified peer
3751 * (invoked with the wireless_dev mutex held)
3752 * @assoc: Request to (re)associate with the specified peer
3753 * (invoked with the wireless_dev mutex held)
3754 * @deauth: Request to deauthenticate from the specified peer
3755 * (invoked with the wireless_dev mutex held)
3756 * @disassoc: Request to disassociate from the specified peer
3757 * (invoked with the wireless_dev mutex held)
3758 *
3759 * @connect: Connect to the ESS with the specified parameters. When connected,
3760 * call cfg80211_connect_result()/cfg80211_connect_bss() with status code
3761 * %WLAN_STATUS_SUCCESS. If the connection fails for some reason, call
3762 * cfg80211_connect_result()/cfg80211_connect_bss() with the status code
3763 * from the AP or cfg80211_connect_timeout() if no frame with status code
3764 * was received.
3765 * The driver is allowed to roam to other BSSes within the ESS when the
3766 * other BSS matches the connect parameters. When such roaming is initiated
3767 * by the driver, the driver is expected to verify that the target matches
3768 * the configured security parameters and to use Reassociation Request
3769 * frame instead of Association Request frame.
3770 * The connect function can also be used to request the driver to perform a
3771 * specific roam when connected to an ESS. In that case, the prev_bssid
3772 * parameter is set to the BSSID of the currently associated BSS as an
3773 * indication of requesting reassociation.
3774 * In both the driver-initiated and new connect() call initiated roaming
3775 * cases, the result of roaming is indicated with a call to
3776 * cfg80211_roamed(). (invoked with the wireless_dev mutex held)
3777 * @update_connect_params: Update the connect parameters while connected to a
3778 * BSS. The updated parameters can be used by driver/firmware for
3779 * subsequent BSS selection (roaming) decisions and to form the
3780 * Authentication/(Re)Association Request frames. This call does not
3781 * request an immediate disassociation or reassociation with the current
3782 * BSS, i.e., this impacts only subsequent (re)associations. The bits in
3783 * changed are defined in &enum cfg80211_connect_params_changed.
3784 * (invoked with the wireless_dev mutex held)
3785 * @disconnect: Disconnect from the BSS/ESS or stop connection attempts if
3786 * connection is in progress. Once done, call cfg80211_disconnected() in
3787 * case connection was already established (invoked with the
3788 * wireless_dev mutex held), otherwise call cfg80211_connect_timeout().
3789 *
3790 * @join_ibss: Join the specified IBSS (or create if necessary). Once done, call
3791 * cfg80211_ibss_joined(), also call that function when changing BSSID due
3792 * to a merge.
3793 * (invoked with the wireless_dev mutex held)
3794 * @leave_ibss: Leave the IBSS.
3795 * (invoked with the wireless_dev mutex held)
3796 *
3797 * @set_mcast_rate: Set the specified multicast rate (only if vif is in ADHOC or
3798 * MESH mode)
3799 *
3800 * @set_wiphy_params: Notify that wiphy parameters have changed;
3801 * @changed bitfield (see &enum wiphy_params_flags) describes which values
3802 * have changed. The actual parameter values are available in
3803 * struct wiphy. If returning an error, no value should be changed.
3804 *
3805 * @set_tx_power: set the transmit power according to the parameters,
3806 * the power passed is in mBm, to get dBm use MBM_TO_DBM(). The
3807 * wdev may be %NULL if power was set for the wiphy, and will
3808 * always be %NULL unless the driver supports per-vif TX power
3809 * (as advertised by the nl80211 feature flag.)
3810 * @get_tx_power: store the current TX power into the dbm variable;
3811 * return 0 if successful
3812 *
3813 * @rfkill_poll: polls the hw rfkill line, use cfg80211 reporting
3814 * functions to adjust rfkill hw state
3815 *
3816 * @dump_survey: get site survey information.
3817 *
3818 * @remain_on_channel: Request the driver to remain awake on the specified
3819 * channel for the specified duration to complete an off-channel
3820 * operation (e.g., public action frame exchange). When the driver is
3821 * ready on the requested channel, it must indicate this with an event
3822 * notification by calling cfg80211_ready_on_channel().
3823 * @cancel_remain_on_channel: Cancel an on-going remain-on-channel operation.
3824 * This allows the operation to be terminated prior to timeout based on
3825 * the duration value.
3826 * @mgmt_tx: Transmit a management frame.
3827 * @mgmt_tx_cancel_wait: Cancel the wait time from transmitting a management
3828 * frame on another channel
3829 *
3830 * @testmode_cmd: run a test mode command; @wdev may be %NULL
3831 * @testmode_dump: Implement a test mode dump. The cb->args[2] and up may be
3832 * used by the function, but 0 and 1 must not be touched. Additionally,
3833 * return error codes other than -ENOBUFS and -ENOENT will terminate the
3834 * dump and return to userspace with an error, so be careful. If any data
3835 * was passed in from userspace then the data/len arguments will be present
3836 * and point to the data contained in %NL80211_ATTR_TESTDATA.
3837 *
3838 * @set_bitrate_mask: set the bitrate mask configuration
3839 *
3840 * @set_pmksa: Cache a PMKID for a BSSID. This is mostly useful for fullmac
3841 * devices running firmwares capable of generating the (re) association
3842 * RSN IE. It allows for faster roaming between WPA2 BSSIDs.
3843 * @del_pmksa: Delete a cached PMKID.
3844 * @flush_pmksa: Flush all cached PMKIDs.
3845 * @set_power_mgmt: Configure WLAN power management. A timeout value of -1
3846 * allows the driver to adjust the dynamic ps timeout value.
3847 * @set_cqm_rssi_config: Configure connection quality monitor RSSI threshold.
3848 * After configuration, the driver should (soon) send an event indicating
3849 * the current level is above/below the configured threshold; this may
3850 * need some care when the configuration is changed (without first being
3851 * disabled.)
3852 * @set_cqm_rssi_range_config: Configure two RSSI thresholds in the
3853 * connection quality monitor. An event is to be sent only when the
3854 * signal level is found to be outside the two values. The driver should
3855 * set %NL80211_EXT_FEATURE_CQM_RSSI_LIST if this method is implemented.
3856 * If it is provided then there's no point providing @set_cqm_rssi_config.
3857 * @set_cqm_txe_config: Configure connection quality monitor TX error
3858 * thresholds.
3859 * @sched_scan_start: Tell the driver to start a scheduled scan.
3860 * @sched_scan_stop: Tell the driver to stop an ongoing scheduled scan with
3861 * given request id. This call must stop the scheduled scan and be ready
3862 * for starting a new one before it returns, i.e. @sched_scan_start may be
3863 * called immediately after that again and should not fail in that case.
3864 * The driver should not call cfg80211_sched_scan_stopped() for a requested
3865 * stop (when this method returns 0).
3866 *
3867 * @update_mgmt_frame_registrations: Notify the driver that management frame
3868 * registrations were updated. The callback is allowed to sleep.
3869 *
3870 * @set_antenna: Set antenna configuration (tx_ant, rx_ant) on the device.
3871 * Parameters are bitmaps of allowed antennas to use for TX/RX. Drivers may
3872 * reject TX/RX mask combinations they cannot support by returning -EINVAL
3873 * (also see nl80211.h @NL80211_ATTR_WIPHY_ANTENNA_TX).
3874 *
3875 * @get_antenna: Get current antenna configuration from device (tx_ant, rx_ant).
3876 *
3877 * @tdls_mgmt: Transmit a TDLS management frame.
3878 * @tdls_oper: Perform a high-level TDLS operation (e.g. TDLS link setup).
3879 *
3880 * @probe_client: probe an associated client, must return a cookie that it
3881 * later passes to cfg80211_probe_status().
3882 *
3883 * @set_noack_map: Set the NoAck Map for the TIDs.
3884 *
3885 * @get_channel: Get the current operating channel for the virtual interface.
3886 * For monitor interfaces, it should return %NULL unless there's a single
3887 * current monitoring channel.
3888 *
3889 * @start_p2p_device: Start the given P2P device.
3890 * @stop_p2p_device: Stop the given P2P device.
3891 *
3892 * @set_mac_acl: Sets MAC address control list in AP and P2P GO mode.
3893 * Parameters include ACL policy, an array of MAC address of stations
3894 * and the number of MAC addresses. If there is already a list in driver
3895 * this new list replaces the existing one. Driver has to clear its ACL
3896 * when number of MAC addresses entries is passed as 0. Drivers which
3897 * advertise the support for MAC based ACL have to implement this callback.
3898 *
3899 * @start_radar_detection: Start radar detection in the driver.
3900 *
3901 * @end_cac: End running CAC, probably because a related CAC
3902 * was finished on another phy.
3903 *
3904 * @update_ft_ies: Provide updated Fast BSS Transition information to the
3905 * driver. If the SME is in the driver/firmware, this information can be
3906 * used in building Authentication and Reassociation Request frames.
3907 *
3908 * @crit_proto_start: Indicates a critical protocol needs more link reliability
3909 * for a given duration (milliseconds). The protocol is provided so the
3910 * driver can take the most appropriate actions.
3911 * @crit_proto_stop: Indicates critical protocol no longer needs increased link
3912 * reliability. This operation can not fail.
3913 * @set_coalesce: Set coalesce parameters.
3914 *
3915 * @channel_switch: initiate channel-switch procedure (with CSA). Driver is
3916 * responsible for veryfing if the switch is possible. Since this is
3917 * inherently tricky driver may decide to disconnect an interface later
3918 * with cfg80211_stop_iface(). This doesn't mean driver can accept
3919 * everything. It should do it's best to verify requests and reject them
3920 * as soon as possible.
3921 *
3922 * @set_qos_map: Set QoS mapping information to the driver
3923 *
3924 * @set_ap_chanwidth: Set the AP (including P2P GO) mode channel width for the
3925 * given interface This is used e.g. for dynamic HT 20/40 MHz channel width
3926 * changes during the lifetime of the BSS.
3927 *
3928 * @add_tx_ts: validate (if admitted_time is 0) or add a TX TS to the device
3929 * with the given parameters; action frame exchange has been handled by
3930 * userspace so this just has to modify the TX path to take the TS into
3931 * account.
3932 * If the admitted time is 0 just validate the parameters to make sure
3933 * the session can be created at all; it is valid to just always return
3934 * success for that but that may result in inefficient behaviour (handshake
3935 * with the peer followed by immediate teardown when the addition is later
3936 * rejected)
3937 * @del_tx_ts: remove an existing TX TS
3938 *
3939 * @join_ocb: join the OCB network with the specified parameters
3940 * (invoked with the wireless_dev mutex held)
3941 * @leave_ocb: leave the current OCB network
3942 * (invoked with the wireless_dev mutex held)
3943 *
3944 * @tdls_channel_switch: Start channel-switching with a TDLS peer. The driver
3945 * is responsible for continually initiating channel-switching operations
3946 * and returning to the base channel for communication with the AP.
3947 * @tdls_cancel_channel_switch: Stop channel-switching with a TDLS peer. Both
3948 * peers must be on the base channel when the call completes.
3949 * @start_nan: Start the NAN interface.
3950 * @stop_nan: Stop the NAN interface.
3951 * @add_nan_func: Add a NAN function. Returns negative value on failure.
3952 * On success @nan_func ownership is transferred to the driver and
3953 * it may access it outside of the scope of this function. The driver
3954 * should free the @nan_func when no longer needed by calling
3955 * cfg80211_free_nan_func().
3956 * On success the driver should assign an instance_id in the
3957 * provided @nan_func.
3958 * @del_nan_func: Delete a NAN function.
3959 * @nan_change_conf: changes NAN configuration. The changed parameters must
3960 * be specified in @changes (using &enum cfg80211_nan_conf_changes);
3961 * All other parameters must be ignored.
3962 *
3963 * @set_multicast_to_unicast: configure multicast to unicast conversion for BSS
3964 *
3965 * @get_txq_stats: Get TXQ stats for interface or phy. If wdev is %NULL, this
3966 * function should return phy stats, and interface stats otherwise.
3967 *
3968 * @set_pmk: configure the PMK to be used for offloaded 802.1X 4-Way handshake.
3969 * If not deleted through @del_pmk the PMK remains valid until disconnect
3970 * upon which the driver should clear it.
3971 * (invoked with the wireless_dev mutex held)
3972 * @del_pmk: delete the previously configured PMK for the given authenticator.
3973 * (invoked with the wireless_dev mutex held)
3974 *
3975 * @external_auth: indicates result of offloaded authentication processing from
3976 * user space
3977 *
3978 * @tx_control_port: TX a control port frame (EAPoL). The noencrypt parameter
3979 * tells the driver that the frame should not be encrypted.
3980 *
3981 * @get_ftm_responder_stats: Retrieve FTM responder statistics, if available.
3982 * Statistics should be cumulative, currently no way to reset is provided.
3983 * @start_pmsr: start peer measurement (e.g. FTM)
3984 * @abort_pmsr: abort peer measurement
3985 *
3986 * @update_owe_info: Provide updated OWE info to driver. Driver implementing SME
3987 * but offloading OWE processing to the user space will get the updated
3988 * DH IE through this interface.
3989 *
3990 * @probe_mesh_link: Probe direct Mesh peer's link quality by sending data frame
3991 * and overrule HWMP path selection algorithm.
3992 * @set_tid_config: TID specific configuration, this can be peer or BSS specific
3993 * This callback may sleep.
3994 * @reset_tid_config: Reset TID specific configuration for the peer, for the
3995 * given TIDs. This callback may sleep.
3996 *
3997 * @set_sar_specs: Update the SAR (TX power) settings.
3998 */
3999struct cfg80211_ops {
4000 int (*suspend)(struct wiphy *wiphy, struct cfg80211_wowlan *wow);
4001 int (*resume)(struct wiphy *wiphy);
4002 void (*set_wakeup)(struct wiphy *wiphy, bool enabled);
4003
4004 struct wireless_dev * (*add_virtual_intf)(struct wiphy *wiphy,
4005 const char *name,
4006 unsigned char name_assign_type,
4007 enum nl80211_iftype type,
4008 struct vif_params *params);
4009 int (*del_virtual_intf)(struct wiphy *wiphy,
4010 struct wireless_dev *wdev);
4011 int (*change_virtual_intf)(struct wiphy *wiphy,
4012 struct net_device *dev,
4013 enum nl80211_iftype type,
4014 struct vif_params *params);
4015
4016 int (*add_key)(struct wiphy *wiphy, struct net_device *netdev,
4017 u8 key_index, bool pairwise, const u8 *mac_addr,
4018 struct key_params *params);
4019 int (*get_key)(struct wiphy *wiphy, struct net_device *netdev,
4020 u8 key_index, bool pairwise, const u8 *mac_addr,
4021 void *cookie,
4022 void (*callback)(void *cookie, struct key_params*));
4023 int (*del_key)(struct wiphy *wiphy, struct net_device *netdev,
4024 u8 key_index, bool pairwise, const u8 *mac_addr);
4025 int (*set_default_key)(struct wiphy *wiphy,
4026 struct net_device *netdev,
4027 u8 key_index, bool unicast, bool multicast);
4028 int (*set_default_mgmt_key)(struct wiphy *wiphy,
4029 struct net_device *netdev,
4030 u8 key_index);
4031 int (*set_default_beacon_key)(struct wiphy *wiphy,
4032 struct net_device *netdev,
4033 u8 key_index);
4034
4035 int (*start_ap)(struct wiphy *wiphy, struct net_device *dev,
4036 struct cfg80211_ap_settings *settings);
4037 int (*change_beacon)(struct wiphy *wiphy, struct net_device *dev,
4038 struct cfg80211_beacon_data *info);
4039 int (*stop_ap)(struct wiphy *wiphy, struct net_device *dev);
4040
4041
4042 int (*add_station)(struct wiphy *wiphy, struct net_device *dev,
4043 const u8 *mac,
4044 struct station_parameters *params);
4045 int (*del_station)(struct wiphy *wiphy, struct net_device *dev,
4046 struct station_del_parameters *params);
4047 int (*change_station)(struct wiphy *wiphy, struct net_device *dev,
4048 const u8 *mac,
4049 struct station_parameters *params);
4050 int (*get_station)(struct wiphy *wiphy, struct net_device *dev,
4051 const u8 *mac, struct station_info *sinfo);
4052 int (*dump_station)(struct wiphy *wiphy, struct net_device *dev,
4053 int idx, u8 *mac, struct station_info *sinfo);
4054
4055 int (*add_mpath)(struct wiphy *wiphy, struct net_device *dev,
4056 const u8 *dst, const u8 *next_hop);
4057 int (*del_mpath)(struct wiphy *wiphy, struct net_device *dev,
4058 const u8 *dst);
4059 int (*change_mpath)(struct wiphy *wiphy, struct net_device *dev,
4060 const u8 *dst, const u8 *next_hop);
4061 int (*get_mpath)(struct wiphy *wiphy, struct net_device *dev,
4062 u8 *dst, u8 *next_hop, struct mpath_info *pinfo);
4063 int (*dump_mpath)(struct wiphy *wiphy, struct net_device *dev,
4064 int idx, u8 *dst, u8 *next_hop,
4065 struct mpath_info *pinfo);
4066 int (*get_mpp)(struct wiphy *wiphy, struct net_device *dev,
4067 u8 *dst, u8 *mpp, struct mpath_info *pinfo);
4068 int (*dump_mpp)(struct wiphy *wiphy, struct net_device *dev,
4069 int idx, u8 *dst, u8 *mpp,
4070 struct mpath_info *pinfo);
4071 int (*get_mesh_config)(struct wiphy *wiphy,
4072 struct net_device *dev,
4073 struct mesh_config *conf);
4074 int (*update_mesh_config)(struct wiphy *wiphy,
4075 struct net_device *dev, u32 mask,
4076 const struct mesh_config *nconf);
4077 int (*join_mesh)(struct wiphy *wiphy, struct net_device *dev,
4078 const struct mesh_config *conf,
4079 const struct mesh_setup *setup);
4080 int (*leave_mesh)(struct wiphy *wiphy, struct net_device *dev);
4081
4082 int (*join_ocb)(struct wiphy *wiphy, struct net_device *dev,
4083 struct ocb_setup *setup);
4084 int (*leave_ocb)(struct wiphy *wiphy, struct net_device *dev);
4085
4086 int (*change_bss)(struct wiphy *wiphy, struct net_device *dev,
4087 struct bss_parameters *params);
4088
4089 int (*set_txq_params)(struct wiphy *wiphy, struct net_device *dev,
4090 struct ieee80211_txq_params *params);
4091
4092 int (*libertas_set_mesh_channel)(struct wiphy *wiphy,
4093 struct net_device *dev,
4094 struct ieee80211_channel *chan);
4095
4096 int (*set_monitor_channel)(struct wiphy *wiphy,
4097 struct cfg80211_chan_def *chandef);
4098
4099 int (*scan)(struct wiphy *wiphy,
4100 struct cfg80211_scan_request *request);
4101 void (*abort_scan)(struct wiphy *wiphy, struct wireless_dev *wdev);
4102
4103 int (*auth)(struct wiphy *wiphy, struct net_device *dev,
4104 struct cfg80211_auth_request *req);
4105 int (*assoc)(struct wiphy *wiphy, struct net_device *dev,
4106 struct cfg80211_assoc_request *req);
4107 int (*deauth)(struct wiphy *wiphy, struct net_device *dev,
4108 struct cfg80211_deauth_request *req);
4109 int (*disassoc)(struct wiphy *wiphy, struct net_device *dev,
4110 struct cfg80211_disassoc_request *req);
4111
4112 int (*connect)(struct wiphy *wiphy, struct net_device *dev,
4113 struct cfg80211_connect_params *sme);
4114 int (*update_connect_params)(struct wiphy *wiphy,
4115 struct net_device *dev,
4116 struct cfg80211_connect_params *sme,
4117 u32 changed);
4118 int (*disconnect)(struct wiphy *wiphy, struct net_device *dev,
4119 u16 reason_code);
4120
4121 int (*join_ibss)(struct wiphy *wiphy, struct net_device *dev,
4122 struct cfg80211_ibss_params *params);
4123 int (*leave_ibss)(struct wiphy *wiphy, struct net_device *dev);
4124
4125 int (*set_mcast_rate)(struct wiphy *wiphy, struct net_device *dev,
4126 int rate[NUM_NL80211_BANDS]);
4127
4128 int (*set_wiphy_params)(struct wiphy *wiphy, u32 changed);
4129
4130 int (*set_tx_power)(struct wiphy *wiphy, struct wireless_dev *wdev,
4131 enum nl80211_tx_power_setting type, int mbm);
4132 int (*get_tx_power)(struct wiphy *wiphy, struct wireless_dev *wdev,
4133 int *dbm);
4134
4135 void (*rfkill_poll)(struct wiphy *wiphy);
4136
4137#ifdef CONFIG_NL80211_TESTMODE
4138 int (*testmode_cmd)(struct wiphy *wiphy, struct wireless_dev *wdev,
4139 void *data, int len);
4140 int (*testmode_dump)(struct wiphy *wiphy, struct sk_buff *skb,
4141 struct netlink_callback *cb,
4142 void *data, int len);
4143#endif
4144
4145 int (*set_bitrate_mask)(struct wiphy *wiphy,
4146 struct net_device *dev,
4147 const u8 *peer,
4148 const struct cfg80211_bitrate_mask *mask);
4149
4150 int (*dump_survey)(struct wiphy *wiphy, struct net_device *netdev,
4151 int idx, struct survey_info *info);
4152
4153 int (*set_pmksa)(struct wiphy *wiphy, struct net_device *netdev,
4154 struct cfg80211_pmksa *pmksa);
4155 int (*del_pmksa)(struct wiphy *wiphy, struct net_device *netdev,
4156 struct cfg80211_pmksa *pmksa);
4157 int (*flush_pmksa)(struct wiphy *wiphy, struct net_device *netdev);
4158
4159 int (*remain_on_channel)(struct wiphy *wiphy,
4160 struct wireless_dev *wdev,
4161 struct ieee80211_channel *chan,
4162 unsigned int duration,
4163 u64 *cookie);
4164 int (*cancel_remain_on_channel)(struct wiphy *wiphy,
4165 struct wireless_dev *wdev,
4166 u64 cookie);
4167
4168 int (*mgmt_tx)(struct wiphy *wiphy, struct wireless_dev *wdev,
4169 struct cfg80211_mgmt_tx_params *params,
4170 u64 *cookie);
4171 int (*mgmt_tx_cancel_wait)(struct wiphy *wiphy,
4172 struct wireless_dev *wdev,
4173 u64 cookie);
4174
4175 int (*set_power_mgmt)(struct wiphy *wiphy, struct net_device *dev,
4176 bool enabled, int timeout);
4177
4178 int (*set_cqm_rssi_config)(struct wiphy *wiphy,
4179 struct net_device *dev,
4180 s32 rssi_thold, u32 rssi_hyst);
4181
4182 int (*set_cqm_rssi_range_config)(struct wiphy *wiphy,
4183 struct net_device *dev,
4184 s32 rssi_low, s32 rssi_high);
4185
4186 int (*set_cqm_txe_config)(struct wiphy *wiphy,
4187 struct net_device *dev,
4188 u32 rate, u32 pkts, u32 intvl);
4189
4190 void (*update_mgmt_frame_registrations)(struct wiphy *wiphy,
4191 struct wireless_dev *wdev,
4192 struct mgmt_frame_regs *upd);
4193
4194 int (*set_antenna)(struct wiphy *wiphy, u32 tx_ant, u32 rx_ant);
4195 int (*get_antenna)(struct wiphy *wiphy, u32 *tx_ant, u32 *rx_ant);
4196
4197 int (*sched_scan_start)(struct wiphy *wiphy,
4198 struct net_device *dev,
4199 struct cfg80211_sched_scan_request *request);
4200 int (*sched_scan_stop)(struct wiphy *wiphy, struct net_device *dev,
4201 u64 reqid);
4202
4203 int (*set_rekey_data)(struct wiphy *wiphy, struct net_device *dev,
4204 struct cfg80211_gtk_rekey_data *data);
4205
4206 int (*tdls_mgmt)(struct wiphy *wiphy, struct net_device *dev,
4207 const u8 *peer, u8 action_code, u8 dialog_token,
4208 u16 status_code, u32 peer_capability,
4209 bool initiator, const u8 *buf, size_t len);
4210 int (*tdls_oper)(struct wiphy *wiphy, struct net_device *dev,
4211 const u8 *peer, enum nl80211_tdls_operation oper);
4212
4213 int (*probe_client)(struct wiphy *wiphy, struct net_device *dev,
4214 const u8 *peer, u64 *cookie);
4215
4216 int (*set_noack_map)(struct wiphy *wiphy,
4217 struct net_device *dev,
4218 u16 noack_map);
4219
4220 int (*get_channel)(struct wiphy *wiphy,
4221 struct wireless_dev *wdev,
4222 struct cfg80211_chan_def *chandef);
4223
4224 int (*start_p2p_device)(struct wiphy *wiphy,
4225 struct wireless_dev *wdev);
4226 void (*stop_p2p_device)(struct wiphy *wiphy,
4227 struct wireless_dev *wdev);
4228
4229 int (*set_mac_acl)(struct wiphy *wiphy, struct net_device *dev,
4230 const struct cfg80211_acl_data *params);
4231
4232 int (*start_radar_detection)(struct wiphy *wiphy,
4233 struct net_device *dev,
4234 struct cfg80211_chan_def *chandef,
4235 u32 cac_time_ms);
4236 void (*end_cac)(struct wiphy *wiphy,
4237 struct net_device *dev);
4238 int (*update_ft_ies)(struct wiphy *wiphy, struct net_device *dev,
4239 struct cfg80211_update_ft_ies_params *ftie);
4240 int (*crit_proto_start)(struct wiphy *wiphy,
4241 struct wireless_dev *wdev,
4242 enum nl80211_crit_proto_id protocol,
4243 u16 duration);
4244 void (*crit_proto_stop)(struct wiphy *wiphy,
4245 struct wireless_dev *wdev);
4246 int (*set_coalesce)(struct wiphy *wiphy,
4247 struct cfg80211_coalesce *coalesce);
4248
4249 int (*channel_switch)(struct wiphy *wiphy,
4250 struct net_device *dev,
4251 struct cfg80211_csa_settings *params);
4252
4253 int (*set_qos_map)(struct wiphy *wiphy,
4254 struct net_device *dev,
4255 struct cfg80211_qos_map *qos_map);
4256
4257 int (*set_ap_chanwidth)(struct wiphy *wiphy, struct net_device *dev,
4258 struct cfg80211_chan_def *chandef);
4259
4260 int (*add_tx_ts)(struct wiphy *wiphy, struct net_device *dev,
4261 u8 tsid, const u8 *peer, u8 user_prio,
4262 u16 admitted_time);
4263 int (*del_tx_ts)(struct wiphy *wiphy, struct net_device *dev,
4264 u8 tsid, const u8 *peer);
4265
4266 int (*tdls_channel_switch)(struct wiphy *wiphy,
4267 struct net_device *dev,
4268 const u8 *addr, u8 oper_class,
4269 struct cfg80211_chan_def *chandef);
4270 void (*tdls_cancel_channel_switch)(struct wiphy *wiphy,
4271 struct net_device *dev,
4272 const u8 *addr);
4273 int (*start_nan)(struct wiphy *wiphy, struct wireless_dev *wdev,
4274 struct cfg80211_nan_conf *conf);
4275 void (*stop_nan)(struct wiphy *wiphy, struct wireless_dev *wdev);
4276 int (*add_nan_func)(struct wiphy *wiphy, struct wireless_dev *wdev,
4277 struct cfg80211_nan_func *nan_func);
4278 void (*del_nan_func)(struct wiphy *wiphy, struct wireless_dev *wdev,
4279 u64 cookie);
4280 int (*nan_change_conf)(struct wiphy *wiphy,
4281 struct wireless_dev *wdev,
4282 struct cfg80211_nan_conf *conf,
4283 u32 changes);
4284
4285 int (*set_multicast_to_unicast)(struct wiphy *wiphy,
4286 struct net_device *dev,
4287 const bool enabled);
4288
4289 int (*get_txq_stats)(struct wiphy *wiphy,
4290 struct wireless_dev *wdev,
4291 struct cfg80211_txq_stats *txqstats);
4292
4293 int (*set_pmk)(struct wiphy *wiphy, struct net_device *dev,
4294 const struct cfg80211_pmk_conf *conf);
4295 int (*del_pmk)(struct wiphy *wiphy, struct net_device *dev,
4296 const u8 *aa);
4297 int (*external_auth)(struct wiphy *wiphy, struct net_device *dev,
4298 struct cfg80211_external_auth_params *params);
4299
4300 int (*tx_control_port)(struct wiphy *wiphy,
4301 struct net_device *dev,
4302 const u8 *buf, size_t len,
4303 const u8 *dest, const __be16 proto,
4304 const bool noencrypt,
4305 u64 *cookie);
4306
4307 int (*get_ftm_responder_stats)(struct wiphy *wiphy,
4308 struct net_device *dev,
4309 struct cfg80211_ftm_responder_stats *ftm_stats);
4310
4311 int (*start_pmsr)(struct wiphy *wiphy, struct wireless_dev *wdev,
4312 struct cfg80211_pmsr_request *request);
4313 void (*abort_pmsr)(struct wiphy *wiphy, struct wireless_dev *wdev,
4314 struct cfg80211_pmsr_request *request);
4315 int (*update_owe_info)(struct wiphy *wiphy, struct net_device *dev,
4316 struct cfg80211_update_owe_info *owe_info);
4317 int (*probe_mesh_link)(struct wiphy *wiphy, struct net_device *dev,
4318 const u8 *buf, size_t len);
4319 int (*set_tid_config)(struct wiphy *wiphy, struct net_device *dev,
4320 struct cfg80211_tid_config *tid_conf);
4321 int (*reset_tid_config)(struct wiphy *wiphy, struct net_device *dev,
4322 const u8 *peer, u8 tids);
4323 int (*set_sar_specs)(struct wiphy *wiphy,
4324 struct cfg80211_sar_specs *sar);
4325};
4326
4327/*
4328 * wireless hardware and networking interfaces structures
4329 * and registration/helper functions
4330 */
4331
4332/**
4333 * enum wiphy_flags - wiphy capability flags
4334 *
4335 * @WIPHY_FLAG_SPLIT_SCAN_6GHZ: if set to true, the scan request will be split
4336 * into two, first for legacy bands and second for UHB.
4337 * @WIPHY_FLAG_NETNS_OK: if not set, do not allow changing the netns of this
4338 * wiphy at all
4339 * @WIPHY_FLAG_PS_ON_BY_DEFAULT: if set to true, powersave will be enabled
4340 * by default -- this flag will be set depending on the kernel's default
4341 * on wiphy_new(), but can be changed by the driver if it has a good
4342 * reason to override the default
4343 * @WIPHY_FLAG_4ADDR_AP: supports 4addr mode even on AP (with a single station
4344 * on a VLAN interface). This flag also serves an extra purpose of
4345 * supporting 4ADDR AP mode on devices which do not support AP/VLAN iftype.
4346 * @WIPHY_FLAG_4ADDR_STATION: supports 4addr mode even as a station
4347 * @WIPHY_FLAG_CONTROL_PORT_PROTOCOL: This device supports setting the
4348 * control port protocol ethertype. The device also honours the
4349 * control_port_no_encrypt flag.
4350 * @WIPHY_FLAG_IBSS_RSN: The device supports IBSS RSN.
4351 * @WIPHY_FLAG_MESH_AUTH: The device supports mesh authentication by routing
4352 * auth frames to userspace. See @NL80211_MESH_SETUP_USERSPACE_AUTH.
4353 * @WIPHY_FLAG_SUPPORTS_FW_ROAM: The device supports roaming feature in the
4354 * firmware.
4355 * @WIPHY_FLAG_AP_UAPSD: The device supports uapsd on AP.
4356 * @WIPHY_FLAG_SUPPORTS_TDLS: The device supports TDLS (802.11z) operation.
4357 * @WIPHY_FLAG_TDLS_EXTERNAL_SETUP: The device does not handle TDLS (802.11z)
4358 * link setup/discovery operations internally. Setup, discovery and
4359 * teardown packets should be sent through the @NL80211_CMD_TDLS_MGMT
4360 * command. When this flag is not set, @NL80211_CMD_TDLS_OPER should be
4361 * used for asking the driver/firmware to perform a TDLS operation.
4362 * @WIPHY_FLAG_HAVE_AP_SME: device integrates AP SME
4363 * @WIPHY_FLAG_REPORTS_OBSS: the device will report beacons from other BSSes
4364 * when there are virtual interfaces in AP mode by calling
4365 * cfg80211_report_obss_beacon().
4366 * @WIPHY_FLAG_AP_PROBE_RESP_OFFLOAD: When operating as an AP, the device
4367 * responds to probe-requests in hardware.
4368 * @WIPHY_FLAG_OFFCHAN_TX: Device supports direct off-channel TX.
4369 * @WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL: Device supports remain-on-channel call.
4370 * @WIPHY_FLAG_SUPPORTS_5_10_MHZ: Device supports 5 MHz and 10 MHz channels.
4371 * @WIPHY_FLAG_HAS_CHANNEL_SWITCH: Device supports channel switch in
4372 * beaconing mode (AP, IBSS, Mesh, ...).
4373 * @WIPHY_FLAG_HAS_STATIC_WEP: The device supports static WEP key installation
4374 * before connection.
4375 * @WIPHY_FLAG_SUPPORTS_EXT_KEK_KCK: The device supports bigger kek and kck keys
4376 */
4377enum wiphy_flags {
4378 WIPHY_FLAG_SUPPORTS_EXT_KEK_KCK = BIT(0),
4379 /* use hole at 1 */
4380 WIPHY_FLAG_SPLIT_SCAN_6GHZ = BIT(2),
4381 WIPHY_FLAG_NETNS_OK = BIT(3),
4382 WIPHY_FLAG_PS_ON_BY_DEFAULT = BIT(4),
4383 WIPHY_FLAG_4ADDR_AP = BIT(5),
4384 WIPHY_FLAG_4ADDR_STATION = BIT(6),
4385 WIPHY_FLAG_CONTROL_PORT_PROTOCOL = BIT(7),
4386 WIPHY_FLAG_IBSS_RSN = BIT(8),
4387 WIPHY_FLAG_MESH_AUTH = BIT(10),
4388 /* use hole at 11 */
4389 /* use hole at 12 */
4390 WIPHY_FLAG_SUPPORTS_FW_ROAM = BIT(13),
4391 WIPHY_FLAG_AP_UAPSD = BIT(14),
4392 WIPHY_FLAG_SUPPORTS_TDLS = BIT(15),
4393 WIPHY_FLAG_TDLS_EXTERNAL_SETUP = BIT(16),
4394 WIPHY_FLAG_HAVE_AP_SME = BIT(17),
4395 WIPHY_FLAG_REPORTS_OBSS = BIT(18),
4396 WIPHY_FLAG_AP_PROBE_RESP_OFFLOAD = BIT(19),
4397 WIPHY_FLAG_OFFCHAN_TX = BIT(20),
4398 WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL = BIT(21),
4399 WIPHY_FLAG_SUPPORTS_5_10_MHZ = BIT(22),
4400 WIPHY_FLAG_HAS_CHANNEL_SWITCH = BIT(23),
4401 WIPHY_FLAG_HAS_STATIC_WEP = BIT(24),
4402};
4403
4404/**
4405 * struct ieee80211_iface_limit - limit on certain interface types
4406 * @max: maximum number of interfaces of these types
4407 * @types: interface types (bits)
4408 */
4409struct ieee80211_iface_limit {
4410 u16 max;
4411 u16 types;
4412};
4413
4414/**
4415 * struct ieee80211_iface_combination - possible interface combination
4416 *
4417 * With this structure the driver can describe which interface
4418 * combinations it supports concurrently.
4419 *
4420 * Examples:
4421 *
4422 * 1. Allow #STA <= 1, #AP <= 1, matching BI, channels = 1, 2 total:
4423 *
4424 * .. code-block:: c
4425 *
4426 * struct ieee80211_iface_limit limits1[] = {
4427 * { .max = 1, .types = BIT(NL80211_IFTYPE_STATION), },
4428 * { .max = 1, .types = BIT(NL80211_IFTYPE_AP}, },
4429 * };
4430 * struct ieee80211_iface_combination combination1 = {
4431 * .limits = limits1,
4432 * .n_limits = ARRAY_SIZE(limits1),
4433 * .max_interfaces = 2,
4434 * .beacon_int_infra_match = true,
4435 * };
4436 *
4437 *
4438 * 2. Allow #{AP, P2P-GO} <= 8, channels = 1, 8 total:
4439 *
4440 * .. code-block:: c
4441 *
4442 * struct ieee80211_iface_limit limits2[] = {
4443 * { .max = 8, .types = BIT(NL80211_IFTYPE_AP) |
4444 * BIT(NL80211_IFTYPE_P2P_GO), },
4445 * };
4446 * struct ieee80211_iface_combination combination2 = {
4447 * .limits = limits2,
4448 * .n_limits = ARRAY_SIZE(limits2),
4449 * .max_interfaces = 8,
4450 * .num_different_channels = 1,
4451 * };
4452 *
4453 *
4454 * 3. Allow #STA <= 1, #{P2P-client,P2P-GO} <= 3 on two channels, 4 total.
4455 *
4456 * This allows for an infrastructure connection and three P2P connections.
4457 *
4458 * .. code-block:: c
4459 *
4460 * struct ieee80211_iface_limit limits3[] = {
4461 * { .max = 1, .types = BIT(NL80211_IFTYPE_STATION), },
4462 * { .max = 3, .types = BIT(NL80211_IFTYPE_P2P_GO) |
4463 * BIT(NL80211_IFTYPE_P2P_CLIENT), },
4464 * };
4465 * struct ieee80211_iface_combination combination3 = {
4466 * .limits = limits3,
4467 * .n_limits = ARRAY_SIZE(limits3),
4468 * .max_interfaces = 4,
4469 * .num_different_channels = 2,
4470 * };
4471 *
4472 */
4473struct ieee80211_iface_combination {
4474 /**
4475 * @limits:
4476 * limits for the given interface types
4477 */
4478 const struct ieee80211_iface_limit *limits;
4479
4480 /**
4481 * @num_different_channels:
4482 * can use up to this many different channels
4483 */
4484 u32 num_different_channels;
4485
4486 /**
4487 * @max_interfaces:
4488 * maximum number of interfaces in total allowed in this group
4489 */
4490 u16 max_interfaces;
4491
4492 /**
4493 * @n_limits:
4494 * number of limitations
4495 */
4496 u8 n_limits;
4497
4498 /**
4499 * @beacon_int_infra_match:
4500 * In this combination, the beacon intervals between infrastructure
4501 * and AP types must match. This is required only in special cases.
4502 */
4503 bool beacon_int_infra_match;
4504
4505 /**
4506 * @radar_detect_widths:
4507 * bitmap of channel widths supported for radar detection
4508 */
4509 u8 radar_detect_widths;
4510
4511 /**
4512 * @radar_detect_regions:
4513 * bitmap of regions supported for radar detection
4514 */
4515 u8 radar_detect_regions;
4516
4517 /**
4518 * @beacon_int_min_gcd:
4519 * This interface combination supports different beacon intervals.
4520 *
4521 * = 0
4522 * all beacon intervals for different interface must be same.
4523 * > 0
4524 * any beacon interval for the interface part of this combination AND
4525 * GCD of all beacon intervals from beaconing interfaces of this
4526 * combination must be greater or equal to this value.
4527 */
4528 u32 beacon_int_min_gcd;
4529};
4530
4531struct ieee80211_txrx_stypes {
4532 u16 tx, rx;
4533};
4534
4535/**
4536 * enum wiphy_wowlan_support_flags - WoWLAN support flags
4537 * @WIPHY_WOWLAN_ANY: supports wakeup for the special "any"
4538 * trigger that keeps the device operating as-is and
4539 * wakes up the host on any activity, for example a
4540 * received packet that passed filtering; note that the
4541 * packet should be preserved in that case
4542 * @WIPHY_WOWLAN_MAGIC_PKT: supports wakeup on magic packet
4543 * (see nl80211.h)
4544 * @WIPHY_WOWLAN_DISCONNECT: supports wakeup on disconnect
4545 * @WIPHY_WOWLAN_SUPPORTS_GTK_REKEY: supports GTK rekeying while asleep
4546 * @WIPHY_WOWLAN_GTK_REKEY_FAILURE: supports wakeup on GTK rekey failure
4547 * @WIPHY_WOWLAN_EAP_IDENTITY_REQ: supports wakeup on EAP identity request
4548 * @WIPHY_WOWLAN_4WAY_HANDSHAKE: supports wakeup on 4-way handshake failure
4549 * @WIPHY_WOWLAN_RFKILL_RELEASE: supports wakeup on RF-kill release
4550 * @WIPHY_WOWLAN_NET_DETECT: supports wakeup on network detection
4551 */
4552enum wiphy_wowlan_support_flags {
4553 WIPHY_WOWLAN_ANY = BIT(0),
4554 WIPHY_WOWLAN_MAGIC_PKT = BIT(1),
4555 WIPHY_WOWLAN_DISCONNECT = BIT(2),
4556 WIPHY_WOWLAN_SUPPORTS_GTK_REKEY = BIT(3),
4557 WIPHY_WOWLAN_GTK_REKEY_FAILURE = BIT(4),
4558 WIPHY_WOWLAN_EAP_IDENTITY_REQ = BIT(5),
4559 WIPHY_WOWLAN_4WAY_HANDSHAKE = BIT(6),
4560 WIPHY_WOWLAN_RFKILL_RELEASE = BIT(7),
4561 WIPHY_WOWLAN_NET_DETECT = BIT(8),
4562};
4563
4564struct wiphy_wowlan_tcp_support {
4565 const struct nl80211_wowlan_tcp_data_token_feature *tok;
4566 u32 data_payload_max;
4567 u32 data_interval_max;
4568 u32 wake_payload_max;
4569 bool seq;
4570};
4571
4572/**
4573 * struct wiphy_wowlan_support - WoWLAN support data
4574 * @flags: see &enum wiphy_wowlan_support_flags
4575 * @n_patterns: number of supported wakeup patterns
4576 * (see nl80211.h for the pattern definition)
4577 * @pattern_max_len: maximum length of each pattern
4578 * @pattern_min_len: minimum length of each pattern
4579 * @max_pkt_offset: maximum Rx packet offset
4580 * @max_nd_match_sets: maximum number of matchsets for net-detect,
4581 * similar, but not necessarily identical, to max_match_sets for
4582 * scheduled scans.
4583 * See &struct cfg80211_sched_scan_request.@match_sets for more
4584 * details.
4585 * @tcp: TCP wakeup support information
4586 */
4587struct wiphy_wowlan_support {
4588 u32 flags;
4589 int n_patterns;
4590 int pattern_max_len;
4591 int pattern_min_len;
4592 int max_pkt_offset;
4593 int max_nd_match_sets;
4594 const struct wiphy_wowlan_tcp_support *tcp;
4595};
4596
4597/**
4598 * struct wiphy_coalesce_support - coalesce support data
4599 * @n_rules: maximum number of coalesce rules
4600 * @max_delay: maximum supported coalescing delay in msecs
4601 * @n_patterns: number of supported patterns in a rule
4602 * (see nl80211.h for the pattern definition)
4603 * @pattern_max_len: maximum length of each pattern
4604 * @pattern_min_len: minimum length of each pattern
4605 * @max_pkt_offset: maximum Rx packet offset
4606 */
4607struct wiphy_coalesce_support {
4608 int n_rules;
4609 int max_delay;
4610 int n_patterns;
4611 int pattern_max_len;
4612 int pattern_min_len;
4613 int max_pkt_offset;
4614};
4615
4616/**
4617 * enum wiphy_vendor_command_flags - validation flags for vendor commands
4618 * @WIPHY_VENDOR_CMD_NEED_WDEV: vendor command requires wdev
4619 * @WIPHY_VENDOR_CMD_NEED_NETDEV: vendor command requires netdev
4620 * @WIPHY_VENDOR_CMD_NEED_RUNNING: interface/wdev must be up & running
4621 * (must be combined with %_WDEV or %_NETDEV)
4622 */
4623enum wiphy_vendor_command_flags {
4624 WIPHY_VENDOR_CMD_NEED_WDEV = BIT(0),
4625 WIPHY_VENDOR_CMD_NEED_NETDEV = BIT(1),
4626 WIPHY_VENDOR_CMD_NEED_RUNNING = BIT(2),
4627};
4628
4629/**
4630 * enum wiphy_opmode_flag - Station's ht/vht operation mode information flags
4631 *
4632 * @STA_OPMODE_MAX_BW_CHANGED: Max Bandwidth changed
4633 * @STA_OPMODE_SMPS_MODE_CHANGED: SMPS mode changed
4634 * @STA_OPMODE_N_SS_CHANGED: max N_SS (number of spatial streams) changed
4635 *
4636 */
4637enum wiphy_opmode_flag {
4638 STA_OPMODE_MAX_BW_CHANGED = BIT(0),
4639 STA_OPMODE_SMPS_MODE_CHANGED = BIT(1),
4640 STA_OPMODE_N_SS_CHANGED = BIT(2),
4641};
4642
4643/**
4644 * struct sta_opmode_info - Station's ht/vht operation mode information
4645 * @changed: contains value from &enum wiphy_opmode_flag
4646 * @smps_mode: New SMPS mode value from &enum nl80211_smps_mode of a station
4647 * @bw: new max bandwidth value from &enum nl80211_chan_width of a station
4648 * @rx_nss: new rx_nss value of a station
4649 */
4650
4651struct sta_opmode_info {
4652 u32 changed;
4653 enum nl80211_smps_mode smps_mode;
4654 enum nl80211_chan_width bw;
4655 u8 rx_nss;
4656};
4657
4658#define VENDOR_CMD_RAW_DATA ((const struct nla_policy *)(long)(-ENODATA))
4659
4660/**
4661 * struct wiphy_vendor_command - vendor command definition
4662 * @info: vendor command identifying information, as used in nl80211
4663 * @flags: flags, see &enum wiphy_vendor_command_flags
4664 * @doit: callback for the operation, note that wdev is %NULL if the
4665 * flags didn't ask for a wdev and non-%NULL otherwise; the data
4666 * pointer may be %NULL if userspace provided no data at all
4667 * @dumpit: dump callback, for transferring bigger/multiple items. The
4668 * @storage points to cb->args[5], ie. is preserved over the multiple
4669 * dumpit calls.
4670 * @policy: policy pointer for attributes within %NL80211_ATTR_VENDOR_DATA.
4671 * Set this to %VENDOR_CMD_RAW_DATA if no policy can be given and the
4672 * attribute is just raw data (e.g. a firmware command).
4673 * @maxattr: highest attribute number in policy
4674 * It's recommended to not have the same sub command with both @doit and
4675 * @dumpit, so that userspace can assume certain ones are get and others
4676 * are used with dump requests.
4677 */
4678struct wiphy_vendor_command {
4679 struct nl80211_vendor_cmd_info info;
4680 u32 flags;
4681 int (*doit)(struct wiphy *wiphy, struct wireless_dev *wdev,
4682 const void *data, int data_len);
4683 int (*dumpit)(struct wiphy *wiphy, struct wireless_dev *wdev,
4684 struct sk_buff *skb, const void *data, int data_len,
4685 unsigned long *storage);
4686 const struct nla_policy *policy;
4687 unsigned int maxattr;
4688};
4689
4690/**
4691 * struct wiphy_iftype_ext_capab - extended capabilities per interface type
4692 * @iftype: interface type
4693 * @extended_capabilities: extended capabilities supported by the driver,
4694 * additional capabilities might be supported by userspace; these are the
4695 * 802.11 extended capabilities ("Extended Capabilities element") and are
4696 * in the same format as in the information element. See IEEE Std
4697 * 802.11-2012 8.4.2.29 for the defined fields.
4698 * @extended_capabilities_mask: mask of the valid values
4699 * @extended_capabilities_len: length of the extended capabilities
4700 */
4701struct wiphy_iftype_ext_capab {
4702 enum nl80211_iftype iftype;
4703 const u8 *extended_capabilities;
4704 const u8 *extended_capabilities_mask;
4705 u8 extended_capabilities_len;
4706};
4707
4708/**
4709 * struct cfg80211_pmsr_capabilities - cfg80211 peer measurement capabilities
4710 * @max_peers: maximum number of peers in a single measurement
4711 * @report_ap_tsf: can report assoc AP's TSF for radio resource measurement
4712 * @randomize_mac_addr: can randomize MAC address for measurement
4713 * @ftm.supported: FTM measurement is supported
4714 * @ftm.asap: ASAP-mode is supported
4715 * @ftm.non_asap: non-ASAP-mode is supported
4716 * @ftm.request_lci: can request LCI data
4717 * @ftm.request_civicloc: can request civic location data
4718 * @ftm.preambles: bitmap of preambles supported (&enum nl80211_preamble)
4719 * @ftm.bandwidths: bitmap of bandwidths supported (&enum nl80211_chan_width)
4720 * @ftm.max_bursts_exponent: maximum burst exponent supported
4721 * (set to -1 if not limited; note that setting this will necessarily
4722 * forbid using the value 15 to let the responder pick)
4723 * @ftm.max_ftms_per_burst: maximum FTMs per burst supported (set to 0 if
4724 * not limited)
4725 * @ftm.trigger_based: trigger based ranging measurement is supported
4726 * @ftm.non_trigger_based: non trigger based ranging measurement is supported
4727 */
4728struct cfg80211_pmsr_capabilities {
4729 unsigned int max_peers;
4730 u8 report_ap_tsf:1,
4731 randomize_mac_addr:1;
4732
4733 struct {
4734 u32 preambles;
4735 u32 bandwidths;
4736 s8 max_bursts_exponent;
4737 u8 max_ftms_per_burst;
4738 u8 supported:1,
4739 asap:1,
4740 non_asap:1,
4741 request_lci:1,
4742 request_civicloc:1,
4743 trigger_based:1,
4744 non_trigger_based:1;
4745 } ftm;
4746};
4747
4748/**
4749 * struct wiphy_iftype_akm_suites - This structure encapsulates supported akm
4750 * suites for interface types defined in @iftypes_mask. Each type in the
4751 * @iftypes_mask must be unique across all instances of iftype_akm_suites.
4752 *
4753 * @iftypes_mask: bitmask of interfaces types
4754 * @akm_suites: points to an array of supported akm suites
4755 * @n_akm_suites: number of supported AKM suites
4756 */
4757struct wiphy_iftype_akm_suites {
4758 u16 iftypes_mask;
4759 const u32 *akm_suites;
4760 int n_akm_suites;
4761};
4762
4763/**
4764 * struct wiphy - wireless hardware description
4765 * @mtx: mutex for the data (structures) of this device
4766 * @reg_notifier: the driver's regulatory notification callback,
4767 * note that if your driver uses wiphy_apply_custom_regulatory()
4768 * the reg_notifier's request can be passed as NULL
4769 * @regd: the driver's regulatory domain, if one was requested via
4770 * the regulatory_hint() API. This can be used by the driver
4771 * on the reg_notifier() if it chooses to ignore future
4772 * regulatory domain changes caused by other drivers.
4773 * @signal_type: signal type reported in &struct cfg80211_bss.
4774 * @cipher_suites: supported cipher suites
4775 * @n_cipher_suites: number of supported cipher suites
4776 * @akm_suites: supported AKM suites. These are the default AKMs supported if
4777 * the supported AKMs not advertized for a specific interface type in
4778 * iftype_akm_suites.
4779 * @n_akm_suites: number of supported AKM suites
4780 * @iftype_akm_suites: array of supported akm suites info per interface type.
4781 * Note that the bits in @iftypes_mask inside this structure cannot
4782 * overlap (i.e. only one occurrence of each type is allowed across all
4783 * instances of iftype_akm_suites).
4784 * @num_iftype_akm_suites: number of interface types for which supported akm
4785 * suites are specified separately.
4786 * @retry_short: Retry limit for short frames (dot11ShortRetryLimit)
4787 * @retry_long: Retry limit for long frames (dot11LongRetryLimit)
4788 * @frag_threshold: Fragmentation threshold (dot11FragmentationThreshold);
4789 * -1 = fragmentation disabled, only odd values >= 256 used
4790 * @rts_threshold: RTS threshold (dot11RTSThreshold); -1 = RTS/CTS disabled
4791 * @_net: the network namespace this wiphy currently lives in
4792 * @perm_addr: permanent MAC address of this device
4793 * @addr_mask: If the device supports multiple MAC addresses by masking,
4794 * set this to a mask with variable bits set to 1, e.g. if the last
4795 * four bits are variable then set it to 00-00-00-00-00-0f. The actual
4796 * variable bits shall be determined by the interfaces added, with
4797 * interfaces not matching the mask being rejected to be brought up.
4798 * @n_addresses: number of addresses in @addresses.
4799 * @addresses: If the device has more than one address, set this pointer
4800 * to a list of addresses (6 bytes each). The first one will be used
4801 * by default for perm_addr. In this case, the mask should be set to
4802 * all-zeroes. In this case it is assumed that the device can handle
4803 * the same number of arbitrary MAC addresses.
4804 * @registered: protects ->resume and ->suspend sysfs callbacks against
4805 * unregister hardware
4806 * @debugfsdir: debugfs directory used for this wiphy (ieee80211/<wiphyname>).
4807 * It will be renamed automatically on wiphy renames
4808 * @dev: (virtual) struct device for this wiphy. The item in
4809 * /sys/class/ieee80211/ points to this. You need use set_wiphy_dev()
4810 * (see below).
4811 * @wext: wireless extension handlers
4812 * @priv: driver private data (sized according to wiphy_new() parameter)
4813 * @interface_modes: bitmask of interfaces types valid for this wiphy,
4814 * must be set by driver
4815 * @iface_combinations: Valid interface combinations array, should not
4816 * list single interface types.
4817 * @n_iface_combinations: number of entries in @iface_combinations array.
4818 * @software_iftypes: bitmask of software interface types, these are not
4819 * subject to any restrictions since they are purely managed in SW.
4820 * @flags: wiphy flags, see &enum wiphy_flags
4821 * @regulatory_flags: wiphy regulatory flags, see
4822 * &enum ieee80211_regulatory_flags
4823 * @features: features advertised to nl80211, see &enum nl80211_feature_flags.
4824 * @ext_features: extended features advertised to nl80211, see
4825 * &enum nl80211_ext_feature_index.
4826 * @bss_priv_size: each BSS struct has private data allocated with it,
4827 * this variable determines its size
4828 * @max_scan_ssids: maximum number of SSIDs the device can scan for in
4829 * any given scan
4830 * @max_sched_scan_reqs: maximum number of scheduled scan requests that
4831 * the device can run concurrently.
4832 * @max_sched_scan_ssids: maximum number of SSIDs the device can scan
4833 * for in any given scheduled scan
4834 * @max_match_sets: maximum number of match sets the device can handle
4835 * when performing a scheduled scan, 0 if filtering is not
4836 * supported.
4837 * @max_scan_ie_len: maximum length of user-controlled IEs device can
4838 * add to probe request frames transmitted during a scan, must not
4839 * include fixed IEs like supported rates
4840 * @max_sched_scan_ie_len: same as max_scan_ie_len, but for scheduled
4841 * scans
4842 * @max_sched_scan_plans: maximum number of scan plans (scan interval and number
4843 * of iterations) for scheduled scan supported by the device.
4844 * @max_sched_scan_plan_interval: maximum interval (in seconds) for a
4845 * single scan plan supported by the device.
4846 * @max_sched_scan_plan_iterations: maximum number of iterations for a single
4847 * scan plan supported by the device.
4848 * @coverage_class: current coverage class
4849 * @fw_version: firmware version for ethtool reporting
4850 * @hw_version: hardware version for ethtool reporting
4851 * @max_num_pmkids: maximum number of PMKIDs supported by device
4852 * @privid: a pointer that drivers can use to identify if an arbitrary
4853 * wiphy is theirs, e.g. in global notifiers
4854 * @bands: information about bands/channels supported by this device
4855 *
4856 * @mgmt_stypes: bitmasks of frame subtypes that can be subscribed to or
4857 * transmitted through nl80211, points to an array indexed by interface
4858 * type
4859 *
4860 * @available_antennas_tx: bitmap of antennas which are available to be
4861 * configured as TX antennas. Antenna configuration commands will be
4862 * rejected unless this or @available_antennas_rx is set.
4863 *
4864 * @available_antennas_rx: bitmap of antennas which are available to be
4865 * configured as RX antennas. Antenna configuration commands will be
4866 * rejected unless this or @available_antennas_tx is set.
4867 *
4868 * @probe_resp_offload:
4869 * Bitmap of supported protocols for probe response offloading.
4870 * See &enum nl80211_probe_resp_offload_support_attr. Only valid
4871 * when the wiphy flag @WIPHY_FLAG_AP_PROBE_RESP_OFFLOAD is set.
4872 *
4873 * @max_remain_on_channel_duration: Maximum time a remain-on-channel operation
4874 * may request, if implemented.
4875 *
4876 * @wowlan: WoWLAN support information
4877 * @wowlan_config: current WoWLAN configuration; this should usually not be
4878 * used since access to it is necessarily racy, use the parameter passed
4879 * to the suspend() operation instead.
4880 *
4881 * @ap_sme_capa: AP SME capabilities, flags from &enum nl80211_ap_sme_features.
4882 * @ht_capa_mod_mask: Specify what ht_cap values can be over-ridden.
4883 * If null, then none can be over-ridden.
4884 * @vht_capa_mod_mask: Specify what VHT capabilities can be over-ridden.
4885 * If null, then none can be over-ridden.
4886 *
4887 * @wdev_list: the list of associated (virtual) interfaces; this list must
4888 * not be modified by the driver, but can be read with RTNL/RCU protection.
4889 *
4890 * @max_acl_mac_addrs: Maximum number of MAC addresses that the device
4891 * supports for ACL.
4892 *
4893 * @extended_capabilities: extended capabilities supported by the driver,
4894 * additional capabilities might be supported by userspace; these are
4895 * the 802.11 extended capabilities ("Extended Capabilities element")
4896 * and are in the same format as in the information element. See
4897 * 802.11-2012 8.4.2.29 for the defined fields. These are the default
4898 * extended capabilities to be used if the capabilities are not specified
4899 * for a specific interface type in iftype_ext_capab.
4900 * @extended_capabilities_mask: mask of the valid values
4901 * @extended_capabilities_len: length of the extended capabilities
4902 * @iftype_ext_capab: array of extended capabilities per interface type
4903 * @num_iftype_ext_capab: number of interface types for which extended
4904 * capabilities are specified separately.
4905 * @coalesce: packet coalescing support information
4906 *
4907 * @vendor_commands: array of vendor commands supported by the hardware
4908 * @n_vendor_commands: number of vendor commands
4909 * @vendor_events: array of vendor events supported by the hardware
4910 * @n_vendor_events: number of vendor events
4911 *
4912 * @max_ap_assoc_sta: maximum number of associated stations supported in AP mode
4913 * (including P2P GO) or 0 to indicate no such limit is advertised. The
4914 * driver is allowed to advertise a theoretical limit that it can reach in
4915 * some cases, but may not always reach.
4916 *
4917 * @max_num_csa_counters: Number of supported csa_counters in beacons
4918 * and probe responses. This value should be set if the driver
4919 * wishes to limit the number of csa counters. Default (0) means
4920 * infinite.
4921 * @bss_select_support: bitmask indicating the BSS selection criteria supported
4922 * by the driver in the .connect() callback. The bit position maps to the
4923 * attribute indices defined in &enum nl80211_bss_select_attr.
4924 *
4925 * @nan_supported_bands: bands supported by the device in NAN mode, a
4926 * bitmap of &enum nl80211_band values. For instance, for
4927 * NL80211_BAND_2GHZ, bit 0 would be set
4928 * (i.e. BIT(NL80211_BAND_2GHZ)).
4929 *
4930 * @txq_limit: configuration of internal TX queue frame limit
4931 * @txq_memory_limit: configuration internal TX queue memory limit
4932 * @txq_quantum: configuration of internal TX queue scheduler quantum
4933 *
4934 * @tx_queue_len: allow setting transmit queue len for drivers not using
4935 * wake_tx_queue
4936 *
4937 * @support_mbssid: can HW support association with nontransmitted AP
4938 * @support_only_he_mbssid: don't parse MBSSID elements if it is not
4939 * HE AP, in order to avoid compatibility issues.
4940 * @support_mbssid must be set for this to have any effect.
4941 *
4942 * @pmsr_capa: peer measurement capabilities
4943 *
4944 * @tid_config_support: describes the per-TID config support that the
4945 * device has
4946 * @tid_config_support.vif: bitmap of attributes (configurations)
4947 * supported by the driver for each vif
4948 * @tid_config_support.peer: bitmap of attributes (configurations)
4949 * supported by the driver for each peer
4950 * @tid_config_support.max_retry: maximum supported retry count for
4951 * long/short retry configuration
4952 *
4953 * @max_data_retry_count: maximum supported per TID retry count for
4954 * configuration through the %NL80211_TID_CONFIG_ATTR_RETRY_SHORT and
4955 * %NL80211_TID_CONFIG_ATTR_RETRY_LONG attributes
4956 * @sar_capa: SAR control capabilities
4957 * @rfkill: a pointer to the rfkill structure
4958 */
4959struct wiphy {
4960 struct mutex mtx;
4961
4962 /* assign these fields before you register the wiphy */
4963
4964 u8 perm_addr[ETH_ALEN];
4965 u8 addr_mask[ETH_ALEN];
4966
4967 struct mac_address *addresses;
4968
4969 const struct ieee80211_txrx_stypes *mgmt_stypes;
4970
4971 const struct ieee80211_iface_combination *iface_combinations;
4972 int n_iface_combinations;
4973 u16 software_iftypes;
4974
4975 u16 n_addresses;
4976
4977 /* Supported interface modes, OR together BIT(NL80211_IFTYPE_...) */
4978 u16 interface_modes;
4979
4980 u16 max_acl_mac_addrs;
4981
4982 u32 flags, regulatory_flags, features;
4983 u8 ext_features[DIV_ROUND_UP(NUM_NL80211_EXT_FEATURES, 8)];
4984
4985 u32 ap_sme_capa;
4986
4987 enum cfg80211_signal_type signal_type;
4988
4989 int bss_priv_size;
4990 u8 max_scan_ssids;
4991 u8 max_sched_scan_reqs;
4992 u8 max_sched_scan_ssids;
4993 u8 max_match_sets;
4994 u16 max_scan_ie_len;
4995 u16 max_sched_scan_ie_len;
4996 u32 max_sched_scan_plans;
4997 u32 max_sched_scan_plan_interval;
4998 u32 max_sched_scan_plan_iterations;
4999
5000 int n_cipher_suites;
5001 const u32 *cipher_suites;
5002
5003 int n_akm_suites;
5004 const u32 *akm_suites;
5005
5006 const struct wiphy_iftype_akm_suites *iftype_akm_suites;
5007 unsigned int num_iftype_akm_suites;
5008
5009 u8 retry_short;
5010 u8 retry_long;
5011 u32 frag_threshold;
5012 u32 rts_threshold;
5013 u8 coverage_class;
5014
5015 char fw_version[ETHTOOL_FWVERS_LEN];
5016 u32 hw_version;
5017
5018#ifdef CONFIG_PM
5019 const struct wiphy_wowlan_support *wowlan;
5020 struct cfg80211_wowlan *wowlan_config;
5021#endif
5022
5023 u16 max_remain_on_channel_duration;
5024
5025 u8 max_num_pmkids;
5026
5027 u32 available_antennas_tx;
5028 u32 available_antennas_rx;
5029
5030 u32 probe_resp_offload;
5031
5032 const u8 *extended_capabilities, *extended_capabilities_mask;
5033 u8 extended_capabilities_len;
5034
5035 const struct wiphy_iftype_ext_capab *iftype_ext_capab;
5036 unsigned int num_iftype_ext_capab;
5037
5038 const void *privid;
5039
5040 struct ieee80211_supported_band *bands[NUM_NL80211_BANDS];
5041
5042 void (*reg_notifier)(struct wiphy *wiphy,
5043 struct regulatory_request *request);
5044
5045 /* fields below are read-only, assigned by cfg80211 */
5046
5047 const struct ieee80211_regdomain __rcu *regd;
5048
5049 struct device dev;
5050
5051 bool registered;
5052
5053 struct dentry *debugfsdir;
5054
5055 const struct ieee80211_ht_cap *ht_capa_mod_mask;
5056 const struct ieee80211_vht_cap *vht_capa_mod_mask;
5057
5058 struct list_head wdev_list;
5059
5060 possible_net_t _net;
5061
5062#ifdef CONFIG_CFG80211_WEXT
5063 const struct iw_handler_def *wext;
5064#endif
5065
5066 const struct wiphy_coalesce_support *coalesce;
5067
5068 const struct wiphy_vendor_command *vendor_commands;
5069 const struct nl80211_vendor_cmd_info *vendor_events;
5070 int n_vendor_commands, n_vendor_events;
5071
5072 u16 max_ap_assoc_sta;
5073
5074 u8 max_num_csa_counters;
5075
5076 u32 bss_select_support;
5077
5078 u8 nan_supported_bands;
5079
5080 u32 txq_limit;
5081 u32 txq_memory_limit;
5082 u32 txq_quantum;
5083
5084 unsigned long tx_queue_len;
5085
5086 u8 support_mbssid:1,
5087 support_only_he_mbssid:1;
5088
5089 const struct cfg80211_pmsr_capabilities *pmsr_capa;
5090
5091 struct {
5092 u64 peer, vif;
5093 u8 max_retry;
5094 } tid_config_support;
5095
5096 u8 max_data_retry_count;
5097
5098 const struct cfg80211_sar_capa *sar_capa;
5099
5100 struct rfkill *rfkill;
5101
5102 char priv[] __aligned(NETDEV_ALIGN);
5103};
5104
5105static inline struct net *wiphy_net(struct wiphy *wiphy)
5106{
5107 return read_pnet(&wiphy->_net);
5108}
5109
5110static inline void wiphy_net_set(struct wiphy *wiphy, struct net *net)
5111{
5112 write_pnet(&wiphy->_net, net);
5113}
5114
5115/**
5116 * wiphy_priv - return priv from wiphy
5117 *
5118 * @wiphy: the wiphy whose priv pointer to return
5119 * Return: The priv of @wiphy.
5120 */
5121static inline void *wiphy_priv(struct wiphy *wiphy)
5122{
5123 BUG_ON(!wiphy);
5124 return &wiphy->priv;
5125}
5126
5127/**
5128 * priv_to_wiphy - return the wiphy containing the priv
5129 *
5130 * @priv: a pointer previously returned by wiphy_priv
5131 * Return: The wiphy of @priv.
5132 */
5133static inline struct wiphy *priv_to_wiphy(void *priv)
5134{
5135 BUG_ON(!priv);
5136 return container_of(priv, struct wiphy, priv);
5137}
5138
5139/**
5140 * set_wiphy_dev - set device pointer for wiphy
5141 *
5142 * @wiphy: The wiphy whose device to bind
5143 * @dev: The device to parent it to
5144 */
5145static inline void set_wiphy_dev(struct wiphy *wiphy, struct device *dev)
5146{
5147 wiphy->dev.parent = dev;
5148}
5149
5150/**
5151 * wiphy_dev - get wiphy dev pointer
5152 *
5153 * @wiphy: The wiphy whose device struct to look up
5154 * Return: The dev of @wiphy.
5155 */
5156static inline struct device *wiphy_dev(struct wiphy *wiphy)
5157{
5158 return wiphy->dev.parent;
5159}
5160
5161/**
5162 * wiphy_name - get wiphy name
5163 *
5164 * @wiphy: The wiphy whose name to return
5165 * Return: The name of @wiphy.
5166 */
5167static inline const char *wiphy_name(const struct wiphy *wiphy)
5168{
5169 return dev_name(&wiphy->dev);
5170}
5171
5172/**
5173 * wiphy_new_nm - create a new wiphy for use with cfg80211
5174 *
5175 * @ops: The configuration operations for this device
5176 * @sizeof_priv: The size of the private area to allocate
5177 * @requested_name: Request a particular name.
5178 * NULL is valid value, and means use the default phy%d naming.
5179 *
5180 * Create a new wiphy and associate the given operations with it.
5181 * @sizeof_priv bytes are allocated for private use.
5182 *
5183 * Return: A pointer to the new wiphy. This pointer must be
5184 * assigned to each netdev's ieee80211_ptr for proper operation.
5185 */
5186struct wiphy *wiphy_new_nm(const struct cfg80211_ops *ops, int sizeof_priv,
5187 const char *requested_name);
5188
5189/**
5190 * wiphy_new - create a new wiphy for use with cfg80211
5191 *
5192 * @ops: The configuration operations for this device
5193 * @sizeof_priv: The size of the private area to allocate
5194 *
5195 * Create a new wiphy and associate the given operations with it.
5196 * @sizeof_priv bytes are allocated for private use.
5197 *
5198 * Return: A pointer to the new wiphy. This pointer must be
5199 * assigned to each netdev's ieee80211_ptr for proper operation.
5200 */
5201static inline struct wiphy *wiphy_new(const struct cfg80211_ops *ops,
5202 int sizeof_priv)
5203{
5204 return wiphy_new_nm(ops, sizeof_priv, NULL);
5205}
5206
5207/**
5208 * wiphy_register - register a wiphy with cfg80211
5209 *
5210 * @wiphy: The wiphy to register.
5211 *
5212 * Return: A non-negative wiphy index or a negative error code.
5213 */
5214int wiphy_register(struct wiphy *wiphy);
5215
5216/* this is a define for better error reporting (file/line) */
5217#define lockdep_assert_wiphy(wiphy) lockdep_assert_held(&(wiphy)->mtx)
5218
5219/**
5220 * rcu_dereference_wiphy - rcu_dereference with debug checking
5221 * @wiphy: the wiphy to check the locking on
5222 * @p: The pointer to read, prior to dereferencing
5223 *
5224 * Do an rcu_dereference(p), but check caller either holds rcu_read_lock()
5225 * or RTNL. Note: Please prefer wiphy_dereference() or rcu_dereference().
5226 */
5227#define rcu_dereference_wiphy(wiphy, p) \
5228 rcu_dereference_check(p, lockdep_is_held(&wiphy->mtx))
5229
5230/**
5231 * wiphy_dereference - fetch RCU pointer when updates are prevented by wiphy mtx
5232 * @wiphy: the wiphy to check the locking on
5233 * @p: The pointer to read, prior to dereferencing
5234 *
5235 * Return the value of the specified RCU-protected pointer, but omit the
5236 * READ_ONCE(), because caller holds the wiphy mutex used for updates.
5237 */
5238#define wiphy_dereference(wiphy, p) \
5239 rcu_dereference_protected(p, lockdep_is_held(&wiphy->mtx))
5240
5241/**
5242 * get_wiphy_regdom - get custom regdomain for the given wiphy
5243 * @wiphy: the wiphy to get the regdomain from
5244 */
5245const struct ieee80211_regdomain *get_wiphy_regdom(struct wiphy *wiphy);
5246
5247/**
5248 * wiphy_unregister - deregister a wiphy from cfg80211
5249 *
5250 * @wiphy: The wiphy to unregister.
5251 *
5252 * After this call, no more requests can be made with this priv
5253 * pointer, but the call may sleep to wait for an outstanding
5254 * request that is being handled.
5255 */
5256void wiphy_unregister(struct wiphy *wiphy);
5257
5258/**
5259 * wiphy_free - free wiphy
5260 *
5261 * @wiphy: The wiphy to free
5262 */
5263void wiphy_free(struct wiphy *wiphy);
5264
5265/* internal structs */
5266struct cfg80211_conn;
5267struct cfg80211_internal_bss;
5268struct cfg80211_cached_keys;
5269struct cfg80211_cqm_config;
5270
5271/**
5272 * wiphy_lock - lock the wiphy
5273 * @wiphy: the wiphy to lock
5274 *
5275 * This is mostly exposed so it can be done around registering and
5276 * unregistering netdevs that aren't created through cfg80211 calls,
5277 * since that requires locking in cfg80211 when the notifiers is
5278 * called, but that cannot differentiate which way it's called.
5279 *
5280 * When cfg80211 ops are called, the wiphy is already locked.
5281 */
5282static inline void wiphy_lock(struct wiphy *wiphy)
5283 __acquires(&wiphy->mtx)
5284{
5285 mutex_lock(&wiphy->mtx);
5286 __acquire(&wiphy->mtx);
5287}
5288
5289/**
5290 * wiphy_unlock - unlock the wiphy again
5291 * @wiphy: the wiphy to unlock
5292 */
5293static inline void wiphy_unlock(struct wiphy *wiphy)
5294 __releases(&wiphy->mtx)
5295{
5296 __release(&wiphy->mtx);
5297 mutex_unlock(&wiphy->mtx);
5298}
5299
5300/**
5301 * struct wireless_dev - wireless device state
5302 *
5303 * For netdevs, this structure must be allocated by the driver
5304 * that uses the ieee80211_ptr field in struct net_device (this
5305 * is intentional so it can be allocated along with the netdev.)
5306 * It need not be registered then as netdev registration will
5307 * be intercepted by cfg80211 to see the new wireless device,
5308 * however, drivers must lock the wiphy before registering or
5309 * unregistering netdevs if they pre-create any netdevs (in ops
5310 * called from cfg80211, the wiphy is already locked.)
5311 *
5312 * For non-netdev uses, it must also be allocated by the driver
5313 * in response to the cfg80211 callbacks that require it, as
5314 * there's no netdev registration in that case it may not be
5315 * allocated outside of callback operations that return it.
5316 *
5317 * @wiphy: pointer to hardware description
5318 * @iftype: interface type
5319 * @registered: is this wdev already registered with cfg80211
5320 * @registering: indicates we're doing registration under wiphy lock
5321 * for the notifier
5322 * @list: (private) Used to collect the interfaces
5323 * @netdev: (private) Used to reference back to the netdev, may be %NULL
5324 * @identifier: (private) Identifier used in nl80211 to identify this
5325 * wireless device if it has no netdev
5326 * @current_bss: (private) Used by the internal configuration code
5327 * @chandef: (private) Used by the internal configuration code to track
5328 * the user-set channel definition.
5329 * @preset_chandef: (private) Used by the internal configuration code to
5330 * track the channel to be used for AP later
5331 * @bssid: (private) Used by the internal configuration code
5332 * @ssid: (private) Used by the internal configuration code
5333 * @ssid_len: (private) Used by the internal configuration code
5334 * @mesh_id_len: (private) Used by the internal configuration code
5335 * @mesh_id_up_len: (private) Used by the internal configuration code
5336 * @wext: (private) Used by the internal wireless extensions compat code
5337 * @wext.ibss: (private) IBSS data part of wext handling
5338 * @wext.connect: (private) connection handling data
5339 * @wext.keys: (private) (WEP) key data
5340 * @wext.ie: (private) extra elements for association
5341 * @wext.ie_len: (private) length of extra elements
5342 * @wext.bssid: (private) selected network BSSID
5343 * @wext.ssid: (private) selected network SSID
5344 * @wext.default_key: (private) selected default key index
5345 * @wext.default_mgmt_key: (private) selected default management key index
5346 * @wext.prev_bssid: (private) previous BSSID for reassociation
5347 * @wext.prev_bssid_valid: (private) previous BSSID validity
5348 * @use_4addr: indicates 4addr mode is used on this interface, must be
5349 * set by driver (if supported) on add_interface BEFORE registering the
5350 * netdev and may otherwise be used by driver read-only, will be update
5351 * by cfg80211 on change_interface
5352 * @mgmt_registrations: list of registrations for management frames
5353 * @mgmt_registrations_lock: lock for the list
5354 * @mgmt_registrations_need_update: mgmt registrations were updated,
5355 * need to propagate the update to the driver
5356 * @mtx: mutex used to lock data in this struct, may be used by drivers
5357 * and some API functions require it held
5358 * @beacon_interval: beacon interval used on this device for transmitting
5359 * beacons, 0 when not valid
5360 * @address: The address for this device, valid only if @netdev is %NULL
5361 * @is_running: true if this is a non-netdev device that has been started, e.g.
5362 * the P2P Device.
5363 * @cac_started: true if DFS channel availability check has been started
5364 * @cac_start_time: timestamp (jiffies) when the dfs state was entered.
5365 * @cac_time_ms: CAC time in ms
5366 * @ps: powersave mode is enabled
5367 * @ps_timeout: dynamic powersave timeout
5368 * @ap_unexpected_nlportid: (private) netlink port ID of application
5369 * registered for unexpected class 3 frames (AP mode)
5370 * @conn: (private) cfg80211 software SME connection state machine data
5371 * @connect_keys: (private) keys to set after connection is established
5372 * @conn_bss_type: connecting/connected BSS type
5373 * @conn_owner_nlportid: (private) connection owner socket port ID
5374 * @disconnect_wk: (private) auto-disconnect work
5375 * @disconnect_bssid: (private) the BSSID to use for auto-disconnect
5376 * @ibss_fixed: (private) IBSS is using fixed BSSID
5377 * @ibss_dfs_possible: (private) IBSS may change to a DFS channel
5378 * @event_list: (private) list for internal event processing
5379 * @event_lock: (private) lock for event list
5380 * @owner_nlportid: (private) owner socket port ID
5381 * @nl_owner_dead: (private) owner socket went away
5382 * @cqm_config: (private) nl80211 RSSI monitor state
5383 * @pmsr_list: (private) peer measurement requests
5384 * @pmsr_lock: (private) peer measurements requests/results lock
5385 * @pmsr_free_wk: (private) peer measurements cleanup work
5386 * @unprot_beacon_reported: (private) timestamp of last
5387 * unprotected beacon report
5388 */
5389struct wireless_dev {
5390 struct wiphy *wiphy;
5391 enum nl80211_iftype iftype;
5392
5393 /* the remainder of this struct should be private to cfg80211 */
5394 struct list_head list;
5395 struct net_device *netdev;
5396
5397 u32 identifier;
5398
5399 struct list_head mgmt_registrations;
5400 spinlock_t mgmt_registrations_lock;
5401 u8 mgmt_registrations_need_update:1;
5402
5403 struct mutex mtx;
5404
5405 bool use_4addr, is_running, registered, registering;
5406
5407 u8 address[ETH_ALEN] __aligned(sizeof(u16));
5408
5409 /* currently used for IBSS and SME - might be rearranged later */
5410 u8 ssid[IEEE80211_MAX_SSID_LEN];
5411 u8 ssid_len, mesh_id_len, mesh_id_up_len;
5412 struct cfg80211_conn *conn;
5413 struct cfg80211_cached_keys *connect_keys;
5414 enum ieee80211_bss_type conn_bss_type;
5415 u32 conn_owner_nlportid;
5416
5417 struct work_struct disconnect_wk;
5418 u8 disconnect_bssid[ETH_ALEN];
5419
5420 struct list_head event_list;
5421 spinlock_t event_lock;
5422
5423 struct cfg80211_internal_bss *current_bss; /* associated / joined */
5424 struct cfg80211_chan_def preset_chandef;
5425 struct cfg80211_chan_def chandef;
5426
5427 bool ibss_fixed;
5428 bool ibss_dfs_possible;
5429
5430 bool ps;
5431 int ps_timeout;
5432
5433 int beacon_interval;
5434
5435 u32 ap_unexpected_nlportid;
5436
5437 u32 owner_nlportid;
5438 bool nl_owner_dead;
5439
5440 bool cac_started;
5441 unsigned long cac_start_time;
5442 unsigned int cac_time_ms;
5443
5444#ifdef CONFIG_CFG80211_WEXT
5445 /* wext data */
5446 struct {
5447 struct cfg80211_ibss_params ibss;
5448 struct cfg80211_connect_params connect;
5449 struct cfg80211_cached_keys *keys;
5450 const u8 *ie;
5451 size_t ie_len;
5452 u8 bssid[ETH_ALEN];
5453 u8 prev_bssid[ETH_ALEN];
5454 u8 ssid[IEEE80211_MAX_SSID_LEN];
5455 s8 default_key, default_mgmt_key;
5456 bool prev_bssid_valid;
5457 } wext;
5458#endif
5459
5460 struct cfg80211_cqm_config *cqm_config;
5461
5462 struct list_head pmsr_list;
5463 spinlock_t pmsr_lock;
5464 struct work_struct pmsr_free_wk;
5465
5466 unsigned long unprot_beacon_reported;
5467};
5468
5469static inline u8 *wdev_address(struct wireless_dev *wdev)
5470{
5471 if (wdev->netdev)
5472 return wdev->netdev->dev_addr;
5473 return wdev->address;
5474}
5475
5476static inline bool wdev_running(struct wireless_dev *wdev)
5477{
5478 if (wdev->netdev)
5479 return netif_running(wdev->netdev);
5480 return wdev->is_running;
5481}
5482
5483/**
5484 * wdev_priv - return wiphy priv from wireless_dev
5485 *
5486 * @wdev: The wireless device whose wiphy's priv pointer to return
5487 * Return: The wiphy priv of @wdev.
5488 */
5489static inline void *wdev_priv(struct wireless_dev *wdev)
5490{
5491 BUG_ON(!wdev);
5492 return wiphy_priv(wdev->wiphy);
5493}
5494
5495/**
5496 * DOC: Utility functions
5497 *
5498 * cfg80211 offers a number of utility functions that can be useful.
5499 */
5500
5501/**
5502 * ieee80211_channel_equal - compare two struct ieee80211_channel
5503 *
5504 * @a: 1st struct ieee80211_channel
5505 * @b: 2nd struct ieee80211_channel
5506 * Return: true if center frequency of @a == @b
5507 */
5508static inline bool
5509ieee80211_channel_equal(struct ieee80211_channel *a,
5510 struct ieee80211_channel *b)
5511{
5512 return (a->center_freq == b->center_freq &&
5513 a->freq_offset == b->freq_offset);
5514}
5515
5516/**
5517 * ieee80211_channel_to_khz - convert ieee80211_channel to frequency in KHz
5518 * @chan: struct ieee80211_channel to convert
5519 * Return: The corresponding frequency (in KHz)
5520 */
5521static inline u32
5522ieee80211_channel_to_khz(const struct ieee80211_channel *chan)
5523{
5524 return MHZ_TO_KHZ(chan->center_freq) + chan->freq_offset;
5525}
5526
5527/**
5528 * ieee80211_s1g_channel_width - get allowed channel width from @chan
5529 *
5530 * Only allowed for band NL80211_BAND_S1GHZ
5531 * @chan: channel
5532 * Return: The allowed channel width for this center_freq
5533 */
5534enum nl80211_chan_width
5535ieee80211_s1g_channel_width(const struct ieee80211_channel *chan);
5536
5537/**
5538 * ieee80211_channel_to_freq_khz - convert channel number to frequency
5539 * @chan: channel number
5540 * @band: band, necessary due to channel number overlap
5541 * Return: The corresponding frequency (in KHz), or 0 if the conversion failed.
5542 */
5543u32 ieee80211_channel_to_freq_khz(int chan, enum nl80211_band band);
5544
5545/**
5546 * ieee80211_channel_to_frequency - convert channel number to frequency
5547 * @chan: channel number
5548 * @band: band, necessary due to channel number overlap
5549 * Return: The corresponding frequency (in MHz), or 0 if the conversion failed.
5550 */
5551static inline int
5552ieee80211_channel_to_frequency(int chan, enum nl80211_band band)
5553{
5554 return KHZ_TO_MHZ(ieee80211_channel_to_freq_khz(chan, band));
5555}
5556
5557/**
5558 * ieee80211_freq_khz_to_channel - convert frequency to channel number
5559 * @freq: center frequency in KHz
5560 * Return: The corresponding channel, or 0 if the conversion failed.
5561 */
5562int ieee80211_freq_khz_to_channel(u32 freq);
5563
5564/**
5565 * ieee80211_frequency_to_channel - convert frequency to channel number
5566 * @freq: center frequency in MHz
5567 * Return: The corresponding channel, or 0 if the conversion failed.
5568 */
5569static inline int
5570ieee80211_frequency_to_channel(int freq)
5571{
5572 return ieee80211_freq_khz_to_channel(MHZ_TO_KHZ(freq));
5573}
5574
5575/**
5576 * ieee80211_get_channel_khz - get channel struct from wiphy for specified
5577 * frequency
5578 * @wiphy: the struct wiphy to get the channel for
5579 * @freq: the center frequency (in KHz) of the channel
5580 * Return: The channel struct from @wiphy at @freq.
5581 */
5582struct ieee80211_channel *
5583ieee80211_get_channel_khz(struct wiphy *wiphy, u32 freq);
5584
5585/**
5586 * ieee80211_get_channel - get channel struct from wiphy for specified frequency
5587 *
5588 * @wiphy: the struct wiphy to get the channel for
5589 * @freq: the center frequency (in MHz) of the channel
5590 * Return: The channel struct from @wiphy at @freq.
5591 */
5592static inline struct ieee80211_channel *
5593ieee80211_get_channel(struct wiphy *wiphy, int freq)
5594{
5595 return ieee80211_get_channel_khz(wiphy, MHZ_TO_KHZ(freq));
5596}
5597
5598/**
5599 * cfg80211_channel_is_psc - Check if the channel is a 6 GHz PSC
5600 * @chan: control channel to check
5601 *
5602 * The Preferred Scanning Channels (PSC) are defined in
5603 * Draft IEEE P802.11ax/D5.0, 26.17.2.3.3
5604 */
5605static inline bool cfg80211_channel_is_psc(struct ieee80211_channel *chan)
5606{
5607 if (chan->band != NL80211_BAND_6GHZ)
5608 return false;
5609
5610 return ieee80211_frequency_to_channel(chan->center_freq) % 16 == 5;
5611}
5612
5613/**
5614 * ieee80211_get_response_rate - get basic rate for a given rate
5615 *
5616 * @sband: the band to look for rates in
5617 * @basic_rates: bitmap of basic rates
5618 * @bitrate: the bitrate for which to find the basic rate
5619 *
5620 * Return: The basic rate corresponding to a given bitrate, that
5621 * is the next lower bitrate contained in the basic rate map,
5622 * which is, for this function, given as a bitmap of indices of
5623 * rates in the band's bitrate table.
5624 */
5625const struct ieee80211_rate *
5626ieee80211_get_response_rate(struct ieee80211_supported_band *sband,
5627 u32 basic_rates, int bitrate);
5628
5629/**
5630 * ieee80211_mandatory_rates - get mandatory rates for a given band
5631 * @sband: the band to look for rates in
5632 * @scan_width: width of the control channel
5633 *
5634 * This function returns a bitmap of the mandatory rates for the given
5635 * band, bits are set according to the rate position in the bitrates array.
5636 */
5637u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband,
5638 enum nl80211_bss_scan_width scan_width);
5639
5640/*
5641 * Radiotap parsing functions -- for controlled injection support
5642 *
5643 * Implemented in net/wireless/radiotap.c
5644 * Documentation in Documentation/networking/radiotap-headers.rst
5645 */
5646
5647struct radiotap_align_size {
5648 uint8_t align:4, size:4;
5649};
5650
5651struct ieee80211_radiotap_namespace {
5652 const struct radiotap_align_size *align_size;
5653 int n_bits;
5654 uint32_t oui;
5655 uint8_t subns;
5656};
5657
5658struct ieee80211_radiotap_vendor_namespaces {
5659 const struct ieee80211_radiotap_namespace *ns;
5660 int n_ns;
5661};
5662
5663/**
5664 * struct ieee80211_radiotap_iterator - tracks walk thru present radiotap args
5665 * @this_arg_index: index of current arg, valid after each successful call
5666 * to ieee80211_radiotap_iterator_next()
5667 * @this_arg: pointer to current radiotap arg; it is valid after each
5668 * call to ieee80211_radiotap_iterator_next() but also after
5669 * ieee80211_radiotap_iterator_init() where it will point to
5670 * the beginning of the actual data portion
5671 * @this_arg_size: length of the current arg, for convenience
5672 * @current_namespace: pointer to the current namespace definition
5673 * (or internally %NULL if the current namespace is unknown)
5674 * @is_radiotap_ns: indicates whether the current namespace is the default
5675 * radiotap namespace or not
5676 *
5677 * @_rtheader: pointer to the radiotap header we are walking through
5678 * @_max_length: length of radiotap header in cpu byte ordering
5679 * @_arg_index: next argument index
5680 * @_arg: next argument pointer
5681 * @_next_bitmap: internal pointer to next present u32
5682 * @_bitmap_shifter: internal shifter for curr u32 bitmap, b0 set == arg present
5683 * @_vns: vendor namespace definitions
5684 * @_next_ns_data: beginning of the next namespace's data
5685 * @_reset_on_ext: internal; reset the arg index to 0 when going to the
5686 * next bitmap word
5687 *
5688 * Describes the radiotap parser state. Fields prefixed with an underscore
5689 * must not be used by users of the parser, only by the parser internally.
5690 */
5691
5692struct ieee80211_radiotap_iterator {
5693 struct ieee80211_radiotap_header *_rtheader;
5694 const struct ieee80211_radiotap_vendor_namespaces *_vns;
5695 const struct ieee80211_radiotap_namespace *current_namespace;
5696
5697 unsigned char *_arg, *_next_ns_data;
5698 __le32 *_next_bitmap;
5699
5700 unsigned char *this_arg;
5701 int this_arg_index;
5702 int this_arg_size;
5703
5704 int is_radiotap_ns;
5705
5706 int _max_length;
5707 int _arg_index;
5708 uint32_t _bitmap_shifter;
5709 int _reset_on_ext;
5710};
5711
5712int
5713ieee80211_radiotap_iterator_init(struct ieee80211_radiotap_iterator *iterator,
5714 struct ieee80211_radiotap_header *radiotap_header,
5715 int max_length,
5716 const struct ieee80211_radiotap_vendor_namespaces *vns);
5717
5718int
5719ieee80211_radiotap_iterator_next(struct ieee80211_radiotap_iterator *iterator);
5720
5721
5722extern const unsigned char rfc1042_header[6];
5723extern const unsigned char bridge_tunnel_header[6];
5724
5725/**
5726 * ieee80211_get_hdrlen_from_skb - get header length from data
5727 *
5728 * @skb: the frame
5729 *
5730 * Given an skb with a raw 802.11 header at the data pointer this function
5731 * returns the 802.11 header length.
5732 *
5733 * Return: The 802.11 header length in bytes (not including encryption
5734 * headers). Or 0 if the data in the sk_buff is too short to contain a valid
5735 * 802.11 header.
5736 */
5737unsigned int ieee80211_get_hdrlen_from_skb(const struct sk_buff *skb);
5738
5739/**
5740 * ieee80211_hdrlen - get header length in bytes from frame control
5741 * @fc: frame control field in little-endian format
5742 * Return: The header length in bytes.
5743 */
5744unsigned int __attribute_const__ ieee80211_hdrlen(__le16 fc);
5745
5746/**
5747 * ieee80211_get_mesh_hdrlen - get mesh extension header length
5748 * @meshhdr: the mesh extension header, only the flags field
5749 * (first byte) will be accessed
5750 * Return: The length of the extension header, which is always at
5751 * least 6 bytes and at most 18 if address 5 and 6 are present.
5752 */
5753unsigned int ieee80211_get_mesh_hdrlen(struct ieee80211s_hdr *meshhdr);
5754
5755/**
5756 * DOC: Data path helpers
5757 *
5758 * In addition to generic utilities, cfg80211 also offers
5759 * functions that help implement the data path for devices
5760 * that do not do the 802.11/802.3 conversion on the device.
5761 */
5762
5763/**
5764 * ieee80211_data_to_8023_exthdr - convert an 802.11 data frame to 802.3
5765 * @skb: the 802.11 data frame
5766 * @ehdr: pointer to a &struct ethhdr that will get the header, instead
5767 * of it being pushed into the SKB
5768 * @addr: the device MAC address
5769 * @iftype: the virtual interface type
5770 * @data_offset: offset of payload after the 802.11 header
5771 * Return: 0 on success. Non-zero on error.
5772 */
5773int ieee80211_data_to_8023_exthdr(struct sk_buff *skb, struct ethhdr *ehdr,
5774 const u8 *addr, enum nl80211_iftype iftype,
5775 u8 data_offset, bool is_amsdu);
5776
5777/**
5778 * ieee80211_data_to_8023 - convert an 802.11 data frame to 802.3
5779 * @skb: the 802.11 data frame
5780 * @addr: the device MAC address
5781 * @iftype: the virtual interface type
5782 * Return: 0 on success. Non-zero on error.
5783 */
5784static inline int ieee80211_data_to_8023(struct sk_buff *skb, const u8 *addr,
5785 enum nl80211_iftype iftype)
5786{
5787 return ieee80211_data_to_8023_exthdr(skb, NULL, addr, iftype, 0, false);
5788}
5789
5790/**
5791 * ieee80211_amsdu_to_8023s - decode an IEEE 802.11n A-MSDU frame
5792 *
5793 * Decode an IEEE 802.11 A-MSDU and convert it to a list of 802.3 frames.
5794 * The @list will be empty if the decode fails. The @skb must be fully
5795 * header-less before being passed in here; it is freed in this function.
5796 *
5797 * @skb: The input A-MSDU frame without any headers.
5798 * @list: The output list of 802.3 frames. It must be allocated and
5799 * initialized by the caller.
5800 * @addr: The device MAC address.
5801 * @iftype: The device interface type.
5802 * @extra_headroom: The hardware extra headroom for SKBs in the @list.
5803 * @check_da: DA to check in the inner ethernet header, or NULL
5804 * @check_sa: SA to check in the inner ethernet header, or NULL
5805 */
5806void ieee80211_amsdu_to_8023s(struct sk_buff *skb, struct sk_buff_head *list,
5807 const u8 *addr, enum nl80211_iftype iftype,
5808 const unsigned int extra_headroom,
5809 const u8 *check_da, const u8 *check_sa);
5810
5811/**
5812 * cfg80211_classify8021d - determine the 802.1p/1d tag for a data frame
5813 * @skb: the data frame
5814 * @qos_map: Interworking QoS mapping or %NULL if not in use
5815 * Return: The 802.1p/1d tag.
5816 */
5817unsigned int cfg80211_classify8021d(struct sk_buff *skb,
5818 struct cfg80211_qos_map *qos_map);
5819
5820/**
5821 * cfg80211_find_elem_match - match information element and byte array in data
5822 *
5823 * @eid: element ID
5824 * @ies: data consisting of IEs
5825 * @len: length of data
5826 * @match: byte array to match
5827 * @match_len: number of bytes in the match array
5828 * @match_offset: offset in the IE data where the byte array should match.
5829 * Note the difference to cfg80211_find_ie_match() which considers
5830 * the offset to start from the element ID byte, but here we take
5831 * the data portion instead.
5832 *
5833 * Return: %NULL if the element ID could not be found or if
5834 * the element is invalid (claims to be longer than the given
5835 * data) or if the byte array doesn't match; otherwise return the
5836 * requested element struct.
5837 *
5838 * Note: There are no checks on the element length other than
5839 * having to fit into the given data and being large enough for the
5840 * byte array to match.
5841 */
5842const struct element *
5843cfg80211_find_elem_match(u8 eid, const u8 *ies, unsigned int len,
5844 const u8 *match, unsigned int match_len,
5845 unsigned int match_offset);
5846
5847/**
5848 * cfg80211_find_ie_match - match information element and byte array in data
5849 *
5850 * @eid: element ID
5851 * @ies: data consisting of IEs
5852 * @len: length of data
5853 * @match: byte array to match
5854 * @match_len: number of bytes in the match array
5855 * @match_offset: offset in the IE where the byte array should match.
5856 * If match_len is zero, this must also be set to zero.
5857 * Otherwise this must be set to 2 or more, because the first
5858 * byte is the element id, which is already compared to eid, and
5859 * the second byte is the IE length.
5860 *
5861 * Return: %NULL if the element ID could not be found or if
5862 * the element is invalid (claims to be longer than the given
5863 * data) or if the byte array doesn't match, or a pointer to the first
5864 * byte of the requested element, that is the byte containing the
5865 * element ID.
5866 *
5867 * Note: There are no checks on the element length other than
5868 * having to fit into the given data and being large enough for the
5869 * byte array to match.
5870 */
5871static inline const u8 *
5872cfg80211_find_ie_match(u8 eid, const u8 *ies, unsigned int len,
5873 const u8 *match, unsigned int match_len,
5874 unsigned int match_offset)
5875{
5876 /* match_offset can't be smaller than 2, unless match_len is
5877 * zero, in which case match_offset must be zero as well.
5878 */
5879 if (WARN_ON((match_len && match_offset < 2) ||
5880 (!match_len && match_offset)))
5881 return NULL;
5882
5883 return (void *)cfg80211_find_elem_match(eid, ies, len,
5884 match, match_len,
5885 match_offset ?
5886 match_offset - 2 : 0);
5887}
5888
5889/**
5890 * cfg80211_find_elem - find information element in data
5891 *
5892 * @eid: element ID
5893 * @ies: data consisting of IEs
5894 * @len: length of data
5895 *
5896 * Return: %NULL if the element ID could not be found or if
5897 * the element is invalid (claims to be longer than the given
5898 * data) or if the byte array doesn't match; otherwise return the
5899 * requested element struct.
5900 *
5901 * Note: There are no checks on the element length other than
5902 * having to fit into the given data.
5903 */
5904static inline const struct element *
5905cfg80211_find_elem(u8 eid, const u8 *ies, int len)
5906{
5907 return cfg80211_find_elem_match(eid, ies, len, NULL, 0, 0);
5908}
5909
5910/**
5911 * cfg80211_find_ie - find information element in data
5912 *
5913 * @eid: element ID
5914 * @ies: data consisting of IEs
5915 * @len: length of data
5916 *
5917 * Return: %NULL if the element ID could not be found or if
5918 * the element is invalid (claims to be longer than the given
5919 * data), or a pointer to the first byte of the requested
5920 * element, that is the byte containing the element ID.
5921 *
5922 * Note: There are no checks on the element length other than
5923 * having to fit into the given data.
5924 */
5925static inline const u8 *cfg80211_find_ie(u8 eid, const u8 *ies, int len)
5926{
5927 return cfg80211_find_ie_match(eid, ies, len, NULL, 0, 0);
5928}
5929
5930/**
5931 * cfg80211_find_ext_elem - find information element with EID Extension in data
5932 *
5933 * @ext_eid: element ID Extension
5934 * @ies: data consisting of IEs
5935 * @len: length of data
5936 *
5937 * Return: %NULL if the etended element could not be found or if
5938 * the element is invalid (claims to be longer than the given
5939 * data) or if the byte array doesn't match; otherwise return the
5940 * requested element struct.
5941 *
5942 * Note: There are no checks on the element length other than
5943 * having to fit into the given data.
5944 */
5945static inline const struct element *
5946cfg80211_find_ext_elem(u8 ext_eid, const u8 *ies, int len)
5947{
5948 return cfg80211_find_elem_match(WLAN_EID_EXTENSION, ies, len,
5949 &ext_eid, 1, 0);
5950}
5951
5952/**
5953 * cfg80211_find_ext_ie - find information element with EID Extension in data
5954 *
5955 * @ext_eid: element ID Extension
5956 * @ies: data consisting of IEs
5957 * @len: length of data
5958 *
5959 * Return: %NULL if the extended element ID could not be found or if
5960 * the element is invalid (claims to be longer than the given
5961 * data), or a pointer to the first byte of the requested
5962 * element, that is the byte containing the element ID.
5963 *
5964 * Note: There are no checks on the element length other than
5965 * having to fit into the given data.
5966 */
5967static inline const u8 *cfg80211_find_ext_ie(u8 ext_eid, const u8 *ies, int len)
5968{
5969 return cfg80211_find_ie_match(WLAN_EID_EXTENSION, ies, len,
5970 &ext_eid, 1, 2);
5971}
5972
5973/**
5974 * cfg80211_find_vendor_elem - find vendor specific information element in data
5975 *
5976 * @oui: vendor OUI
5977 * @oui_type: vendor-specific OUI type (must be < 0xff), negative means any
5978 * @ies: data consisting of IEs
5979 * @len: length of data
5980 *
5981 * Return: %NULL if the vendor specific element ID could not be found or if the
5982 * element is invalid (claims to be longer than the given data); otherwise
5983 * return the element structure for the requested element.
5984 *
5985 * Note: There are no checks on the element length other than having to fit into
5986 * the given data.
5987 */
5988const struct element *cfg80211_find_vendor_elem(unsigned int oui, int oui_type,
5989 const u8 *ies,
5990 unsigned int len);
5991
5992/**
5993 * cfg80211_find_vendor_ie - find vendor specific information element in data
5994 *
5995 * @oui: vendor OUI
5996 * @oui_type: vendor-specific OUI type (must be < 0xff), negative means any
5997 * @ies: data consisting of IEs
5998 * @len: length of data
5999 *
6000 * Return: %NULL if the vendor specific element ID could not be found or if the
6001 * element is invalid (claims to be longer than the given data), or a pointer to
6002 * the first byte of the requested element, that is the byte containing the
6003 * element ID.
6004 *
6005 * Note: There are no checks on the element length other than having to fit into
6006 * the given data.
6007 */
6008static inline const u8 *
6009cfg80211_find_vendor_ie(unsigned int oui, int oui_type,
6010 const u8 *ies, unsigned int len)
6011{
6012 return (void *)cfg80211_find_vendor_elem(oui, oui_type, ies, len);
6013}
6014
6015/**
6016 * cfg80211_send_layer2_update - send layer 2 update frame
6017 *
6018 * @dev: network device
6019 * @addr: STA MAC address
6020 *
6021 * Wireless drivers can use this function to update forwarding tables in bridge
6022 * devices upon STA association.
6023 */
6024void cfg80211_send_layer2_update(struct net_device *dev, const u8 *addr);
6025
6026/**
6027 * DOC: Regulatory enforcement infrastructure
6028 *
6029 * TODO
6030 */
6031
6032/**
6033 * regulatory_hint - driver hint to the wireless core a regulatory domain
6034 * @wiphy: the wireless device giving the hint (used only for reporting
6035 * conflicts)
6036 * @alpha2: the ISO/IEC 3166 alpha2 the driver claims its regulatory domain
6037 * should be in. If @rd is set this should be NULL. Note that if you
6038 * set this to NULL you should still set rd->alpha2 to some accepted
6039 * alpha2.
6040 *
6041 * Wireless drivers can use this function to hint to the wireless core
6042 * what it believes should be the current regulatory domain by
6043 * giving it an ISO/IEC 3166 alpha2 country code it knows its regulatory
6044 * domain should be in or by providing a completely build regulatory domain.
6045 * If the driver provides an ISO/IEC 3166 alpha2 userspace will be queried
6046 * for a regulatory domain structure for the respective country.
6047 *
6048 * The wiphy must have been registered to cfg80211 prior to this call.
6049 * For cfg80211 drivers this means you must first use wiphy_register(),
6050 * for mac80211 drivers you must first use ieee80211_register_hw().
6051 *
6052 * Drivers should check the return value, its possible you can get
6053 * an -ENOMEM.
6054 *
6055 * Return: 0 on success. -ENOMEM.
6056 */
6057int regulatory_hint(struct wiphy *wiphy, const char *alpha2);
6058
6059/**
6060 * regulatory_set_wiphy_regd - set regdom info for self managed drivers
6061 * @wiphy: the wireless device we want to process the regulatory domain on
6062 * @rd: the regulatory domain informatoin to use for this wiphy
6063 *
6064 * Set the regulatory domain information for self-managed wiphys, only they
6065 * may use this function. See %REGULATORY_WIPHY_SELF_MANAGED for more
6066 * information.
6067 *
6068 * Return: 0 on success. -EINVAL, -EPERM
6069 */
6070int regulatory_set_wiphy_regd(struct wiphy *wiphy,
6071 struct ieee80211_regdomain *rd);
6072
6073/**
6074 * regulatory_set_wiphy_regd_sync - set regdom for self-managed drivers
6075 * @wiphy: the wireless device we want to process the regulatory domain on
6076 * @rd: the regulatory domain information to use for this wiphy
6077 *
6078 * This functions requires the RTNL and the wiphy mutex to be held and
6079 * applies the new regdomain synchronously to this wiphy. For more details
6080 * see regulatory_set_wiphy_regd().
6081 *
6082 * Return: 0 on success. -EINVAL, -EPERM
6083 */
6084int regulatory_set_wiphy_regd_sync(struct wiphy *wiphy,
6085 struct ieee80211_regdomain *rd);
6086
6087/**
6088 * wiphy_apply_custom_regulatory - apply a custom driver regulatory domain
6089 * @wiphy: the wireless device we want to process the regulatory domain on
6090 * @regd: the custom regulatory domain to use for this wiphy
6091 *
6092 * Drivers can sometimes have custom regulatory domains which do not apply
6093 * to a specific country. Drivers can use this to apply such custom regulatory
6094 * domains. This routine must be called prior to wiphy registration. The
6095 * custom regulatory domain will be trusted completely and as such previous
6096 * default channel settings will be disregarded. If no rule is found for a
6097 * channel on the regulatory domain the channel will be disabled.
6098 * Drivers using this for a wiphy should also set the wiphy flag
6099 * REGULATORY_CUSTOM_REG or cfg80211 will set it for the wiphy
6100 * that called this helper.
6101 */
6102void wiphy_apply_custom_regulatory(struct wiphy *wiphy,
6103 const struct ieee80211_regdomain *regd);
6104
6105/**
6106 * freq_reg_info - get regulatory information for the given frequency
6107 * @wiphy: the wiphy for which we want to process this rule for
6108 * @center_freq: Frequency in KHz for which we want regulatory information for
6109 *
6110 * Use this function to get the regulatory rule for a specific frequency on
6111 * a given wireless device. If the device has a specific regulatory domain
6112 * it wants to follow we respect that unless a country IE has been received
6113 * and processed already.
6114 *
6115 * Return: A valid pointer, or, when an error occurs, for example if no rule
6116 * can be found, the return value is encoded using ERR_PTR(). Use IS_ERR() to
6117 * check and PTR_ERR() to obtain the numeric return value. The numeric return
6118 * value will be -ERANGE if we determine the given center_freq does not even
6119 * have a regulatory rule for a frequency range in the center_freq's band.
6120 * See freq_in_rule_band() for our current definition of a band -- this is
6121 * purely subjective and right now it's 802.11 specific.
6122 */
6123const struct ieee80211_reg_rule *freq_reg_info(struct wiphy *wiphy,
6124 u32 center_freq);
6125
6126/**
6127 * reg_initiator_name - map regulatory request initiator enum to name
6128 * @initiator: the regulatory request initiator
6129 *
6130 * You can use this to map the regulatory request initiator enum to a
6131 * proper string representation.
6132 */
6133const char *reg_initiator_name(enum nl80211_reg_initiator initiator);
6134
6135/**
6136 * regulatory_pre_cac_allowed - check if pre-CAC allowed in the current regdom
6137 * @wiphy: wiphy for which pre-CAC capability is checked.
6138 *
6139 * Pre-CAC is allowed only in some regdomains (notable ETSI).
6140 */
6141bool regulatory_pre_cac_allowed(struct wiphy *wiphy);
6142
6143/**
6144 * DOC: Internal regulatory db functions
6145 *
6146 */
6147
6148/**
6149 * reg_query_regdb_wmm - Query internal regulatory db for wmm rule
6150 * Regulatory self-managed driver can use it to proactively
6151 *
6152 * @alpha2: the ISO/IEC 3166 alpha2 wmm rule to be queried.
6153 * @freq: the freqency(in MHz) to be queried.
6154 * @rule: pointer to store the wmm rule from the regulatory db.
6155 *
6156 * Self-managed wireless drivers can use this function to query
6157 * the internal regulatory database to check whether the given
6158 * ISO/IEC 3166 alpha2 country and freq have wmm rule limitations.
6159 *
6160 * Drivers should check the return value, its possible you can get
6161 * an -ENODATA.
6162 *
6163 * Return: 0 on success. -ENODATA.
6164 */
6165int reg_query_regdb_wmm(char *alpha2, int freq,
6166 struct ieee80211_reg_rule *rule);
6167
6168/*
6169 * callbacks for asynchronous cfg80211 methods, notification
6170 * functions and BSS handling helpers
6171 */
6172
6173/**
6174 * cfg80211_scan_done - notify that scan finished
6175 *
6176 * @request: the corresponding scan request
6177 * @info: information about the completed scan
6178 */
6179void cfg80211_scan_done(struct cfg80211_scan_request *request,
6180 struct cfg80211_scan_info *info);
6181
6182/**
6183 * cfg80211_sched_scan_results - notify that new scan results are available
6184 *
6185 * @wiphy: the wiphy which got scheduled scan results
6186 * @reqid: identifier for the related scheduled scan request
6187 */
6188void cfg80211_sched_scan_results(struct wiphy *wiphy, u64 reqid);
6189
6190/**
6191 * cfg80211_sched_scan_stopped - notify that the scheduled scan has stopped
6192 *
6193 * @wiphy: the wiphy on which the scheduled scan stopped
6194 * @reqid: identifier for the related scheduled scan request
6195 *
6196 * The driver can call this function to inform cfg80211 that the
6197 * scheduled scan had to be stopped, for whatever reason. The driver
6198 * is then called back via the sched_scan_stop operation when done.
6199 */
6200void cfg80211_sched_scan_stopped(struct wiphy *wiphy, u64 reqid);
6201
6202/**
6203 * cfg80211_sched_scan_stopped_locked - notify that the scheduled scan has stopped
6204 *
6205 * @wiphy: the wiphy on which the scheduled scan stopped
6206 * @reqid: identifier for the related scheduled scan request
6207 *
6208 * The driver can call this function to inform cfg80211 that the
6209 * scheduled scan had to be stopped, for whatever reason. The driver
6210 * is then called back via the sched_scan_stop operation when done.
6211 * This function should be called with the wiphy mutex held.
6212 */
6213void cfg80211_sched_scan_stopped_locked(struct wiphy *wiphy, u64 reqid);
6214
6215/**
6216 * cfg80211_inform_bss_frame_data - inform cfg80211 of a received BSS frame
6217 * @wiphy: the wiphy reporting the BSS
6218 * @data: the BSS metadata
6219 * @mgmt: the management frame (probe response or beacon)
6220 * @len: length of the management frame
6221 * @gfp: context flags
6222 *
6223 * This informs cfg80211 that BSS information was found and
6224 * the BSS should be updated/added.
6225 *
6226 * Return: A referenced struct, must be released with cfg80211_put_bss()!
6227 * Or %NULL on error.
6228 */
6229struct cfg80211_bss * __must_check
6230cfg80211_inform_bss_frame_data(struct wiphy *wiphy,
6231 struct cfg80211_inform_bss *data,
6232 struct ieee80211_mgmt *mgmt, size_t len,
6233 gfp_t gfp);
6234
6235static inline struct cfg80211_bss * __must_check
6236cfg80211_inform_bss_width_frame(struct wiphy *wiphy,
6237 struct ieee80211_channel *rx_channel,
6238 enum nl80211_bss_scan_width scan_width,
6239 struct ieee80211_mgmt *mgmt, size_t len,
6240 s32 signal, gfp_t gfp)
6241{
6242 struct cfg80211_inform_bss data = {
6243 .chan = rx_channel,
6244 .scan_width = scan_width,
6245 .signal = signal,
6246 };
6247
6248 return cfg80211_inform_bss_frame_data(wiphy, &data, mgmt, len, gfp);
6249}
6250
6251static inline struct cfg80211_bss * __must_check
6252cfg80211_inform_bss_frame(struct wiphy *wiphy,
6253 struct ieee80211_channel *rx_channel,
6254 struct ieee80211_mgmt *mgmt, size_t len,
6255 s32 signal, gfp_t gfp)
6256{
6257 struct cfg80211_inform_bss data = {
6258 .chan = rx_channel,
6259 .scan_width = NL80211_BSS_CHAN_WIDTH_20,
6260 .signal = signal,
6261 };
6262
6263 return cfg80211_inform_bss_frame_data(wiphy, &data, mgmt, len, gfp);
6264}
6265
6266/**
6267 * cfg80211_gen_new_bssid - generate a nontransmitted BSSID for multi-BSSID
6268 * @bssid: transmitter BSSID
6269 * @max_bssid: max BSSID indicator, taken from Multiple BSSID element
6270 * @mbssid_index: BSSID index, taken from Multiple BSSID index element
6271 * @new_bssid: calculated nontransmitted BSSID
6272 */
6273static inline void cfg80211_gen_new_bssid(const u8 *bssid, u8 max_bssid,
6274 u8 mbssid_index, u8 *new_bssid)
6275{
6276 u64 bssid_u64 = ether_addr_to_u64(bssid);
6277 u64 mask = GENMASK_ULL(max_bssid - 1, 0);
6278 u64 new_bssid_u64;
6279
6280 new_bssid_u64 = bssid_u64 & ~mask;
6281
6282 new_bssid_u64 |= ((bssid_u64 & mask) + mbssid_index) & mask;
6283
6284 u64_to_ether_addr(new_bssid_u64, new_bssid);
6285}
6286
6287/**
6288 * cfg80211_is_element_inherited - returns if element ID should be inherited
6289 * @element: element to check
6290 * @non_inherit_element: non inheritance element
6291 */
6292bool cfg80211_is_element_inherited(const struct element *element,
6293 const struct element *non_inherit_element);
6294
6295/**
6296 * cfg80211_merge_profile - merges a MBSSID profile if it is split between IEs
6297 * @ie: ies
6298 * @ielen: length of IEs
6299 * @mbssid_elem: current MBSSID element
6300 * @sub_elem: current MBSSID subelement (profile)
6301 * @merged_ie: location of the merged profile
6302 * @max_copy_len: max merged profile length
6303 */
6304size_t cfg80211_merge_profile(const u8 *ie, size_t ielen,
6305 const struct element *mbssid_elem,
6306 const struct element *sub_elem,
6307 u8 *merged_ie, size_t max_copy_len);
6308
6309/**
6310 * enum cfg80211_bss_frame_type - frame type that the BSS data came from
6311 * @CFG80211_BSS_FTYPE_UNKNOWN: driver doesn't know whether the data is
6312 * from a beacon or probe response
6313 * @CFG80211_BSS_FTYPE_BEACON: data comes from a beacon
6314 * @CFG80211_BSS_FTYPE_PRESP: data comes from a probe response
6315 */
6316enum cfg80211_bss_frame_type {
6317 CFG80211_BSS_FTYPE_UNKNOWN,
6318 CFG80211_BSS_FTYPE_BEACON,
6319 CFG80211_BSS_FTYPE_PRESP,
6320};
6321
6322/**
6323 * cfg80211_inform_bss_data - inform cfg80211 of a new BSS
6324 *
6325 * @wiphy: the wiphy reporting the BSS
6326 * @data: the BSS metadata
6327 * @ftype: frame type (if known)
6328 * @bssid: the BSSID of the BSS
6329 * @tsf: the TSF sent by the peer in the beacon/probe response (or 0)
6330 * @capability: the capability field sent by the peer
6331 * @beacon_interval: the beacon interval announced by the peer
6332 * @ie: additional IEs sent by the peer
6333 * @ielen: length of the additional IEs
6334 * @gfp: context flags
6335 *
6336 * This informs cfg80211 that BSS information was found and
6337 * the BSS should be updated/added.
6338 *
6339 * Return: A referenced struct, must be released with cfg80211_put_bss()!
6340 * Or %NULL on error.
6341 */
6342struct cfg80211_bss * __must_check
6343cfg80211_inform_bss_data(struct wiphy *wiphy,
6344 struct cfg80211_inform_bss *data,
6345 enum cfg80211_bss_frame_type ftype,
6346 const u8 *bssid, u64 tsf, u16 capability,
6347 u16 beacon_interval, const u8 *ie, size_t ielen,
6348 gfp_t gfp);
6349
6350static inline struct cfg80211_bss * __must_check
6351cfg80211_inform_bss_width(struct wiphy *wiphy,
6352 struct ieee80211_channel *rx_channel,
6353 enum nl80211_bss_scan_width scan_width,
6354 enum cfg80211_bss_frame_type ftype,
6355 const u8 *bssid, u64 tsf, u16 capability,
6356 u16 beacon_interval, const u8 *ie, size_t ielen,
6357 s32 signal, gfp_t gfp)
6358{
6359 struct cfg80211_inform_bss data = {
6360 .chan = rx_channel,
6361 .scan_width = scan_width,
6362 .signal = signal,
6363 };
6364
6365 return cfg80211_inform_bss_data(wiphy, &data, ftype, bssid, tsf,
6366 capability, beacon_interval, ie, ielen,
6367 gfp);
6368}
6369
6370static inline struct cfg80211_bss * __must_check
6371cfg80211_inform_bss(struct wiphy *wiphy,
6372 struct ieee80211_channel *rx_channel,
6373 enum cfg80211_bss_frame_type ftype,
6374 const u8 *bssid, u64 tsf, u16 capability,
6375 u16 beacon_interval, const u8 *ie, size_t ielen,
6376 s32 signal, gfp_t gfp)
6377{
6378 struct cfg80211_inform_bss data = {
6379 .chan = rx_channel,
6380 .scan_width = NL80211_BSS_CHAN_WIDTH_20,
6381 .signal = signal,
6382 };
6383
6384 return cfg80211_inform_bss_data(wiphy, &data, ftype, bssid, tsf,
6385 capability, beacon_interval, ie, ielen,
6386 gfp);
6387}
6388
6389/**
6390 * cfg80211_get_bss - get a BSS reference
6391 * @wiphy: the wiphy this BSS struct belongs to
6392 * @channel: the channel to search on (or %NULL)
6393 * @bssid: the desired BSSID (or %NULL)
6394 * @ssid: the desired SSID (or %NULL)
6395 * @ssid_len: length of the SSID (or 0)
6396 * @bss_type: type of BSS, see &enum ieee80211_bss_type
6397 * @privacy: privacy filter, see &enum ieee80211_privacy
6398 */
6399struct cfg80211_bss *cfg80211_get_bss(struct wiphy *wiphy,
6400 struct ieee80211_channel *channel,
6401 const u8 *bssid,
6402 const u8 *ssid, size_t ssid_len,
6403 enum ieee80211_bss_type bss_type,
6404 enum ieee80211_privacy privacy);
6405static inline struct cfg80211_bss *
6406cfg80211_get_ibss(struct wiphy *wiphy,
6407 struct ieee80211_channel *channel,
6408 const u8 *ssid, size_t ssid_len)
6409{
6410 return cfg80211_get_bss(wiphy, channel, NULL, ssid, ssid_len,
6411 IEEE80211_BSS_TYPE_IBSS,
6412 IEEE80211_PRIVACY_ANY);
6413}
6414
6415/**
6416 * cfg80211_ref_bss - reference BSS struct
6417 * @wiphy: the wiphy this BSS struct belongs to
6418 * @bss: the BSS struct to reference
6419 *
6420 * Increments the refcount of the given BSS struct.
6421 */
6422void cfg80211_ref_bss(struct wiphy *wiphy, struct cfg80211_bss *bss);
6423
6424/**
6425 * cfg80211_put_bss - unref BSS struct
6426 * @wiphy: the wiphy this BSS struct belongs to
6427 * @bss: the BSS struct
6428 *
6429 * Decrements the refcount of the given BSS struct.
6430 */
6431void cfg80211_put_bss(struct wiphy *wiphy, struct cfg80211_bss *bss);
6432
6433/**
6434 * cfg80211_unlink_bss - unlink BSS from internal data structures
6435 * @wiphy: the wiphy
6436 * @bss: the bss to remove
6437 *
6438 * This function removes the given BSS from the internal data structures
6439 * thereby making it no longer show up in scan results etc. Use this
6440 * function when you detect a BSS is gone. Normally BSSes will also time
6441 * out, so it is not necessary to use this function at all.
6442 */
6443void cfg80211_unlink_bss(struct wiphy *wiphy, struct cfg80211_bss *bss);
6444
6445/**
6446 * cfg80211_bss_iter - iterate all BSS entries
6447 *
6448 * This function iterates over the BSS entries associated with the given wiphy
6449 * and calls the callback for the iterated BSS. The iterator function is not
6450 * allowed to call functions that might modify the internal state of the BSS DB.
6451 *
6452 * @wiphy: the wiphy
6453 * @chandef: if given, the iterator function will be called only if the channel
6454 * of the currently iterated BSS is a subset of the given channel.
6455 * @iter: the iterator function to call
6456 * @iter_data: an argument to the iterator function
6457 */
6458void cfg80211_bss_iter(struct wiphy *wiphy,
6459 struct cfg80211_chan_def *chandef,
6460 void (*iter)(struct wiphy *wiphy,
6461 struct cfg80211_bss *bss,
6462 void *data),
6463 void *iter_data);
6464
6465static inline enum nl80211_bss_scan_width
6466cfg80211_chandef_to_scan_width(const struct cfg80211_chan_def *chandef)
6467{
6468 switch (chandef->width) {
6469 case NL80211_CHAN_WIDTH_5:
6470 return NL80211_BSS_CHAN_WIDTH_5;
6471 case NL80211_CHAN_WIDTH_10:
6472 return NL80211_BSS_CHAN_WIDTH_10;
6473 default:
6474 return NL80211_BSS_CHAN_WIDTH_20;
6475 }
6476}
6477
6478/**
6479 * cfg80211_rx_mlme_mgmt - notification of processed MLME management frame
6480 * @dev: network device
6481 * @buf: authentication frame (header + body)
6482 * @len: length of the frame data
6483 *
6484 * This function is called whenever an authentication, disassociation or
6485 * deauthentication frame has been received and processed in station mode.
6486 * After being asked to authenticate via cfg80211_ops::auth() the driver must
6487 * call either this function or cfg80211_auth_timeout().
6488 * After being asked to associate via cfg80211_ops::assoc() the driver must
6489 * call either this function or cfg80211_auth_timeout().
6490 * While connected, the driver must calls this for received and processed
6491 * disassociation and deauthentication frames. If the frame couldn't be used
6492 * because it was unprotected, the driver must call the function
6493 * cfg80211_rx_unprot_mlme_mgmt() instead.
6494 *
6495 * This function may sleep. The caller must hold the corresponding wdev's mutex.
6496 */
6497void cfg80211_rx_mlme_mgmt(struct net_device *dev, const u8 *buf, size_t len);
6498
6499/**
6500 * cfg80211_auth_timeout - notification of timed out authentication
6501 * @dev: network device
6502 * @addr: The MAC address of the device with which the authentication timed out
6503 *
6504 * This function may sleep. The caller must hold the corresponding wdev's
6505 * mutex.
6506 */
6507void cfg80211_auth_timeout(struct net_device *dev, const u8 *addr);
6508
6509/**
6510 * cfg80211_rx_assoc_resp - notification of processed association response
6511 * @dev: network device
6512 * @bss: the BSS that association was requested with, ownership of the pointer
6513 * moves to cfg80211 in this call
6514 * @buf: (Re)Association Response frame (header + body)
6515 * @len: length of the frame data
6516 * @uapsd_queues: bitmap of queues configured for uapsd. Same format
6517 * as the AC bitmap in the QoS info field
6518 * @req_ies: information elements from the (Re)Association Request frame
6519 * @req_ies_len: length of req_ies data
6520 *
6521 * After being asked to associate via cfg80211_ops::assoc() the driver must
6522 * call either this function or cfg80211_auth_timeout().
6523 *
6524 * This function may sleep. The caller must hold the corresponding wdev's mutex.
6525 */
6526void cfg80211_rx_assoc_resp(struct net_device *dev,
6527 struct cfg80211_bss *bss,
6528 const u8 *buf, size_t len,
6529 int uapsd_queues,
6530 const u8 *req_ies, size_t req_ies_len);
6531
6532/**
6533 * cfg80211_assoc_timeout - notification of timed out association
6534 * @dev: network device
6535 * @bss: The BSS entry with which association timed out.
6536 *
6537 * This function may sleep. The caller must hold the corresponding wdev's mutex.
6538 */
6539void cfg80211_assoc_timeout(struct net_device *dev, struct cfg80211_bss *bss);
6540
6541/**
6542 * cfg80211_abandon_assoc - notify cfg80211 of abandoned association attempt
6543 * @dev: network device
6544 * @bss: The BSS entry with which association was abandoned.
6545 *
6546 * Call this whenever - for reasons reported through other API, like deauth RX,
6547 * an association attempt was abandoned.
6548 * This function may sleep. The caller must hold the corresponding wdev's mutex.
6549 */
6550void cfg80211_abandon_assoc(struct net_device *dev, struct cfg80211_bss *bss);
6551
6552/**
6553 * cfg80211_tx_mlme_mgmt - notification of transmitted deauth/disassoc frame
6554 * @dev: network device
6555 * @buf: 802.11 frame (header + body)
6556 * @len: length of the frame data
6557 * @reconnect: immediate reconnect is desired (include the nl80211 attribute)
6558 *
6559 * This function is called whenever deauthentication has been processed in
6560 * station mode. This includes both received deauthentication frames and
6561 * locally generated ones. This function may sleep. The caller must hold the
6562 * corresponding wdev's mutex.
6563 */
6564void cfg80211_tx_mlme_mgmt(struct net_device *dev, const u8 *buf, size_t len,
6565 bool reconnect);
6566
6567/**
6568 * cfg80211_rx_unprot_mlme_mgmt - notification of unprotected mlme mgmt frame
6569 * @dev: network device
6570 * @buf: received management frame (header + body)
6571 * @len: length of the frame data
6572 *
6573 * This function is called whenever a received deauthentication or dissassoc
6574 * frame has been dropped in station mode because of MFP being used but the
6575 * frame was not protected. This is also used to notify reception of a Beacon
6576 * frame that was dropped because it did not include a valid MME MIC while
6577 * beacon protection was enabled (BIGTK configured in station mode).
6578 *
6579 * This function may sleep.
6580 */
6581void cfg80211_rx_unprot_mlme_mgmt(struct net_device *dev,
6582 const u8 *buf, size_t len);
6583
6584/**
6585 * cfg80211_michael_mic_failure - notification of Michael MIC failure (TKIP)
6586 * @dev: network device
6587 * @addr: The source MAC address of the frame
6588 * @key_type: The key type that the received frame used
6589 * @key_id: Key identifier (0..3). Can be -1 if missing.
6590 * @tsc: The TSC value of the frame that generated the MIC failure (6 octets)
6591 * @gfp: allocation flags
6592 *
6593 * This function is called whenever the local MAC detects a MIC failure in a
6594 * received frame. This matches with MLME-MICHAELMICFAILURE.indication()
6595 * primitive.
6596 */
6597void cfg80211_michael_mic_failure(struct net_device *dev, const u8 *addr,
6598 enum nl80211_key_type key_type, int key_id,
6599 const u8 *tsc, gfp_t gfp);
6600
6601/**
6602 * cfg80211_ibss_joined - notify cfg80211 that device joined an IBSS
6603 *
6604 * @dev: network device
6605 * @bssid: the BSSID of the IBSS joined
6606 * @channel: the channel of the IBSS joined
6607 * @gfp: allocation flags
6608 *
6609 * This function notifies cfg80211 that the device joined an IBSS or
6610 * switched to a different BSSID. Before this function can be called,
6611 * either a beacon has to have been received from the IBSS, or one of
6612 * the cfg80211_inform_bss{,_frame} functions must have been called
6613 * with the locally generated beacon -- this guarantees that there is
6614 * always a scan result for this IBSS. cfg80211 will handle the rest.
6615 */
6616void cfg80211_ibss_joined(struct net_device *dev, const u8 *bssid,
6617 struct ieee80211_channel *channel, gfp_t gfp);
6618
6619/**
6620 * cfg80211_notify_new_peer_candidate - notify cfg80211 of a new mesh peer
6621 * candidate
6622 *
6623 * @dev: network device
6624 * @macaddr: the MAC address of the new candidate
6625 * @ie: information elements advertised by the peer candidate
6626 * @ie_len: length of the information elements buffer
6627 * @gfp: allocation flags
6628 *
6629 * This function notifies cfg80211 that the mesh peer candidate has been
6630 * detected, most likely via a beacon or, less likely, via a probe response.
6631 * cfg80211 then sends a notification to userspace.
6632 */
6633void cfg80211_notify_new_peer_candidate(struct net_device *dev,
6634 const u8 *macaddr, const u8 *ie, u8 ie_len,
6635 int sig_dbm, gfp_t gfp);
6636
6637/**
6638 * DOC: RFkill integration
6639 *
6640 * RFkill integration in cfg80211 is almost invisible to drivers,
6641 * as cfg80211 automatically registers an rfkill instance for each
6642 * wireless device it knows about. Soft kill is also translated
6643 * into disconnecting and turning all interfaces off, drivers are
6644 * expected to turn off the device when all interfaces are down.
6645 *
6646 * However, devices may have a hard RFkill line, in which case they
6647 * also need to interact with the rfkill subsystem, via cfg80211.
6648 * They can do this with a few helper functions documented here.
6649 */
6650
6651/**
6652 * wiphy_rfkill_set_hw_state_reason - notify cfg80211 about hw block state
6653 * @wiphy: the wiphy
6654 * @blocked: block status
6655 * @reason: one of reasons in &enum rfkill_hard_block_reasons
6656 */
6657void wiphy_rfkill_set_hw_state_reason(struct wiphy *wiphy, bool blocked,
6658 enum rfkill_hard_block_reasons reason);
6659
6660static inline void wiphy_rfkill_set_hw_state(struct wiphy *wiphy, bool blocked)
6661{
6662 wiphy_rfkill_set_hw_state_reason(wiphy, blocked,
6663 RFKILL_HARD_BLOCK_SIGNAL);
6664}
6665
6666/**
6667 * wiphy_rfkill_start_polling - start polling rfkill
6668 * @wiphy: the wiphy
6669 */
6670void wiphy_rfkill_start_polling(struct wiphy *wiphy);
6671
6672/**
6673 * wiphy_rfkill_stop_polling - stop polling rfkill
6674 * @wiphy: the wiphy
6675 */
6676static inline void wiphy_rfkill_stop_polling(struct wiphy *wiphy)
6677{
6678 rfkill_pause_polling(wiphy->rfkill);
6679}
6680
6681/**
6682 * DOC: Vendor commands
6683 *
6684 * Occasionally, there are special protocol or firmware features that
6685 * can't be implemented very openly. For this and similar cases, the
6686 * vendor command functionality allows implementing the features with
6687 * (typically closed-source) userspace and firmware, using nl80211 as
6688 * the configuration mechanism.
6689 *
6690 * A driver supporting vendor commands must register them as an array
6691 * in struct wiphy, with handlers for each one, each command has an
6692 * OUI and sub command ID to identify it.
6693 *
6694 * Note that this feature should not be (ab)used to implement protocol
6695 * features that could openly be shared across drivers. In particular,
6696 * it must never be required to use vendor commands to implement any
6697 * "normal" functionality that higher-level userspace like connection
6698 * managers etc. need.
6699 */
6700
6701struct sk_buff *__cfg80211_alloc_reply_skb(struct wiphy *wiphy,
6702 enum nl80211_commands cmd,
6703 enum nl80211_attrs attr,
6704 int approxlen);
6705
6706struct sk_buff *__cfg80211_alloc_event_skb(struct wiphy *wiphy,
6707 struct wireless_dev *wdev,
6708 enum nl80211_commands cmd,
6709 enum nl80211_attrs attr,
6710 unsigned int portid,
6711 int vendor_event_idx,
6712 int approxlen, gfp_t gfp);
6713
6714void __cfg80211_send_event_skb(struct sk_buff *skb, gfp_t gfp);
6715
6716/**
6717 * cfg80211_vendor_cmd_alloc_reply_skb - allocate vendor command reply
6718 * @wiphy: the wiphy
6719 * @approxlen: an upper bound of the length of the data that will
6720 * be put into the skb
6721 *
6722 * This function allocates and pre-fills an skb for a reply to
6723 * a vendor command. Since it is intended for a reply, calling
6724 * it outside of a vendor command's doit() operation is invalid.
6725 *
6726 * The returned skb is pre-filled with some identifying data in
6727 * a way that any data that is put into the skb (with skb_put(),
6728 * nla_put() or similar) will end up being within the
6729 * %NL80211_ATTR_VENDOR_DATA attribute, so all that needs to be done
6730 * with the skb is adding data for the corresponding userspace tool
6731 * which can then read that data out of the vendor data attribute.
6732 * You must not modify the skb in any other way.
6733 *
6734 * When done, call cfg80211_vendor_cmd_reply() with the skb and return
6735 * its error code as the result of the doit() operation.
6736 *
6737 * Return: An allocated and pre-filled skb. %NULL if any errors happen.
6738 */
6739static inline struct sk_buff *
6740cfg80211_vendor_cmd_alloc_reply_skb(struct wiphy *wiphy, int approxlen)
6741{
6742 return __cfg80211_alloc_reply_skb(wiphy, NL80211_CMD_VENDOR,
6743 NL80211_ATTR_VENDOR_DATA, approxlen);
6744}
6745
6746/**
6747 * cfg80211_vendor_cmd_reply - send the reply skb
6748 * @skb: The skb, must have been allocated with
6749 * cfg80211_vendor_cmd_alloc_reply_skb()
6750 *
6751 * Since calling this function will usually be the last thing
6752 * before returning from the vendor command doit() you should
6753 * return the error code. Note that this function consumes the
6754 * skb regardless of the return value.
6755 *
6756 * Return: An error code or 0 on success.
6757 */
6758int cfg80211_vendor_cmd_reply(struct sk_buff *skb);
6759
6760/**
6761 * cfg80211_vendor_cmd_get_sender - get the current sender netlink ID
6762 * @wiphy: the wiphy
6763 *
6764 * Return the current netlink port ID in a vendor command handler.
6765 * Valid to call only there.
6766 */
6767unsigned int cfg80211_vendor_cmd_get_sender(struct wiphy *wiphy);
6768
6769/**
6770 * cfg80211_vendor_event_alloc - allocate vendor-specific event skb
6771 * @wiphy: the wiphy
6772 * @wdev: the wireless device
6773 * @event_idx: index of the vendor event in the wiphy's vendor_events
6774 * @approxlen: an upper bound of the length of the data that will
6775 * be put into the skb
6776 * @gfp: allocation flags
6777 *
6778 * This function allocates and pre-fills an skb for an event on the
6779 * vendor-specific multicast group.
6780 *
6781 * If wdev != NULL, both the ifindex and identifier of the specified
6782 * wireless device are added to the event message before the vendor data
6783 * attribute.
6784 *
6785 * When done filling the skb, call cfg80211_vendor_event() with the
6786 * skb to send the event.
6787 *
6788 * Return: An allocated and pre-filled skb. %NULL if any errors happen.
6789 */
6790static inline struct sk_buff *
6791cfg80211_vendor_event_alloc(struct wiphy *wiphy, struct wireless_dev *wdev,
6792 int approxlen, int event_idx, gfp_t gfp)
6793{
6794 return __cfg80211_alloc_event_skb(wiphy, wdev, NL80211_CMD_VENDOR,
6795 NL80211_ATTR_VENDOR_DATA,
6796 0, event_idx, approxlen, gfp);
6797}
6798
6799/**
6800 * cfg80211_vendor_event_alloc_ucast - alloc unicast vendor-specific event skb
6801 * @wiphy: the wiphy
6802 * @wdev: the wireless device
6803 * @event_idx: index of the vendor event in the wiphy's vendor_events
6804 * @portid: port ID of the receiver
6805 * @approxlen: an upper bound of the length of the data that will
6806 * be put into the skb
6807 * @gfp: allocation flags
6808 *
6809 * This function allocates and pre-fills an skb for an event to send to
6810 * a specific (userland) socket. This socket would previously have been
6811 * obtained by cfg80211_vendor_cmd_get_sender(), and the caller MUST take
6812 * care to register a netlink notifier to see when the socket closes.
6813 *
6814 * If wdev != NULL, both the ifindex and identifier of the specified
6815 * wireless device are added to the event message before the vendor data
6816 * attribute.
6817 *
6818 * When done filling the skb, call cfg80211_vendor_event() with the
6819 * skb to send the event.
6820 *
6821 * Return: An allocated and pre-filled skb. %NULL if any errors happen.
6822 */
6823static inline struct sk_buff *
6824cfg80211_vendor_event_alloc_ucast(struct wiphy *wiphy,
6825 struct wireless_dev *wdev,
6826 unsigned int portid, int approxlen,
6827 int event_idx, gfp_t gfp)
6828{
6829 return __cfg80211_alloc_event_skb(wiphy, wdev, NL80211_CMD_VENDOR,
6830 NL80211_ATTR_VENDOR_DATA,
6831 portid, event_idx, approxlen, gfp);
6832}
6833
6834/**
6835 * cfg80211_vendor_event - send the event
6836 * @skb: The skb, must have been allocated with cfg80211_vendor_event_alloc()
6837 * @gfp: allocation flags
6838 *
6839 * This function sends the given @skb, which must have been allocated
6840 * by cfg80211_vendor_event_alloc(), as an event. It always consumes it.
6841 */
6842static inline void cfg80211_vendor_event(struct sk_buff *skb, gfp_t gfp)
6843{
6844 __cfg80211_send_event_skb(skb, gfp);
6845}
6846
6847#ifdef CONFIG_NL80211_TESTMODE
6848/**
6849 * DOC: Test mode
6850 *
6851 * Test mode is a set of utility functions to allow drivers to
6852 * interact with driver-specific tools to aid, for instance,
6853 * factory programming.
6854 *
6855 * This chapter describes how drivers interact with it, for more
6856 * information see the nl80211 book's chapter on it.
6857 */
6858
6859/**
6860 * cfg80211_testmode_alloc_reply_skb - allocate testmode reply
6861 * @wiphy: the wiphy
6862 * @approxlen: an upper bound of the length of the data that will
6863 * be put into the skb
6864 *
6865 * This function allocates and pre-fills an skb for a reply to
6866 * the testmode command. Since it is intended for a reply, calling
6867 * it outside of the @testmode_cmd operation is invalid.
6868 *
6869 * The returned skb is pre-filled with the wiphy index and set up in
6870 * a way that any data that is put into the skb (with skb_put(),
6871 * nla_put() or similar) will end up being within the
6872 * %NL80211_ATTR_TESTDATA attribute, so all that needs to be done
6873 * with the skb is adding data for the corresponding userspace tool
6874 * which can then read that data out of the testdata attribute. You
6875 * must not modify the skb in any other way.
6876 *
6877 * When done, call cfg80211_testmode_reply() with the skb and return
6878 * its error code as the result of the @testmode_cmd operation.
6879 *
6880 * Return: An allocated and pre-filled skb. %NULL if any errors happen.
6881 */
6882static inline struct sk_buff *
6883cfg80211_testmode_alloc_reply_skb(struct wiphy *wiphy, int approxlen)
6884{
6885 return __cfg80211_alloc_reply_skb(wiphy, NL80211_CMD_TESTMODE,
6886 NL80211_ATTR_TESTDATA, approxlen);
6887}
6888
6889/**
6890 * cfg80211_testmode_reply - send the reply skb
6891 * @skb: The skb, must have been allocated with
6892 * cfg80211_testmode_alloc_reply_skb()
6893 *
6894 * Since calling this function will usually be the last thing
6895 * before returning from the @testmode_cmd you should return
6896 * the error code. Note that this function consumes the skb
6897 * regardless of the return value.
6898 *
6899 * Return: An error code or 0 on success.
6900 */
6901static inline int cfg80211_testmode_reply(struct sk_buff *skb)
6902{
6903 return cfg80211_vendor_cmd_reply(skb);
6904}
6905
6906/**
6907 * cfg80211_testmode_alloc_event_skb - allocate testmode event
6908 * @wiphy: the wiphy
6909 * @approxlen: an upper bound of the length of the data that will
6910 * be put into the skb
6911 * @gfp: allocation flags
6912 *
6913 * This function allocates and pre-fills an skb for an event on the
6914 * testmode multicast group.
6915 *
6916 * The returned skb is set up in the same way as with
6917 * cfg80211_testmode_alloc_reply_skb() but prepared for an event. As
6918 * there, you should simply add data to it that will then end up in the
6919 * %NL80211_ATTR_TESTDATA attribute. Again, you must not modify the skb
6920 * in any other way.
6921 *
6922 * When done filling the skb, call cfg80211_testmode_event() with the
6923 * skb to send the event.
6924 *
6925 * Return: An allocated and pre-filled skb. %NULL if any errors happen.
6926 */
6927static inline struct sk_buff *
6928cfg80211_testmode_alloc_event_skb(struct wiphy *wiphy, int approxlen, gfp_t gfp)
6929{
6930 return __cfg80211_alloc_event_skb(wiphy, NULL, NL80211_CMD_TESTMODE,
6931 NL80211_ATTR_TESTDATA, 0, -1,
6932 approxlen, gfp);
6933}
6934
6935/**
6936 * cfg80211_testmode_event - send the event
6937 * @skb: The skb, must have been allocated with
6938 * cfg80211_testmode_alloc_event_skb()
6939 * @gfp: allocation flags
6940 *
6941 * This function sends the given @skb, which must have been allocated
6942 * by cfg80211_testmode_alloc_event_skb(), as an event. It always
6943 * consumes it.
6944 */
6945static inline void cfg80211_testmode_event(struct sk_buff *skb, gfp_t gfp)
6946{
6947 __cfg80211_send_event_skb(skb, gfp);
6948}
6949
6950#define CFG80211_TESTMODE_CMD(cmd) .testmode_cmd = (cmd),
6951#define CFG80211_TESTMODE_DUMP(cmd) .testmode_dump = (cmd),
6952#else
6953#define CFG80211_TESTMODE_CMD(cmd)
6954#define CFG80211_TESTMODE_DUMP(cmd)
6955#endif
6956
6957/**
6958 * struct cfg80211_fils_resp_params - FILS connection response params
6959 * @kek: KEK derived from a successful FILS connection (may be %NULL)
6960 * @kek_len: Length of @fils_kek in octets
6961 * @update_erp_next_seq_num: Boolean value to specify whether the value in
6962 * @erp_next_seq_num is valid.
6963 * @erp_next_seq_num: The next sequence number to use in ERP message in
6964 * FILS Authentication. This value should be specified irrespective of the
6965 * status for a FILS connection.
6966 * @pmk: A new PMK if derived from a successful FILS connection (may be %NULL).
6967 * @pmk_len: Length of @pmk in octets
6968 * @pmkid: A new PMKID if derived from a successful FILS connection or the PMKID
6969 * used for this FILS connection (may be %NULL).
6970 */
6971struct cfg80211_fils_resp_params {
6972 const u8 *kek;
6973 size_t kek_len;
6974 bool update_erp_next_seq_num;
6975 u16 erp_next_seq_num;
6976 const u8 *pmk;
6977 size_t pmk_len;
6978 const u8 *pmkid;
6979};
6980
6981/**
6982 * struct cfg80211_connect_resp_params - Connection response params
6983 * @status: Status code, %WLAN_STATUS_SUCCESS for successful connection, use
6984 * %WLAN_STATUS_UNSPECIFIED_FAILURE if your device cannot give you
6985 * the real status code for failures. If this call is used to report a
6986 * failure due to a timeout (e.g., not receiving an Authentication frame
6987 * from the AP) instead of an explicit rejection by the AP, -1 is used to
6988 * indicate that this is a failure, but without a status code.
6989 * @timeout_reason is used to report the reason for the timeout in that
6990 * case.
6991 * @bssid: The BSSID of the AP (may be %NULL)
6992 * @bss: Entry of bss to which STA got connected to, can be obtained through
6993 * cfg80211_get_bss() (may be %NULL). But it is recommended to store the
6994 * bss from the connect_request and hold a reference to it and return
6995 * through this param to avoid a warning if the bss is expired during the
6996 * connection, esp. for those drivers implementing connect op.
6997 * Only one parameter among @bssid and @bss needs to be specified.
6998 * @req_ie: Association request IEs (may be %NULL)
6999 * @req_ie_len: Association request IEs length
7000 * @resp_ie: Association response IEs (may be %NULL)
7001 * @resp_ie_len: Association response IEs length
7002 * @fils: FILS connection response parameters.
7003 * @timeout_reason: Reason for connection timeout. This is used when the
7004 * connection fails due to a timeout instead of an explicit rejection from
7005 * the AP. %NL80211_TIMEOUT_UNSPECIFIED is used when the timeout reason is
7006 * not known. This value is used only if @status < 0 to indicate that the
7007 * failure is due to a timeout and not due to explicit rejection by the AP.
7008 * This value is ignored in other cases (@status >= 0).
7009 */
7010struct cfg80211_connect_resp_params {
7011 int status;
7012 const u8 *bssid;
7013 struct cfg80211_bss *bss;
7014 const u8 *req_ie;
7015 size_t req_ie_len;
7016 const u8 *resp_ie;
7017 size_t resp_ie_len;
7018 struct cfg80211_fils_resp_params fils;
7019 enum nl80211_timeout_reason timeout_reason;
7020};
7021
7022/**
7023 * cfg80211_connect_done - notify cfg80211 of connection result
7024 *
7025 * @dev: network device
7026 * @params: connection response parameters
7027 * @gfp: allocation flags
7028 *
7029 * It should be called by the underlying driver once execution of the connection
7030 * request from connect() has been completed. This is similar to
7031 * cfg80211_connect_bss(), but takes a structure pointer for connection response
7032 * parameters. Only one of the functions among cfg80211_connect_bss(),
7033 * cfg80211_connect_result(), cfg80211_connect_timeout(),
7034 * and cfg80211_connect_done() should be called.
7035 */
7036void cfg80211_connect_done(struct net_device *dev,
7037 struct cfg80211_connect_resp_params *params,
7038 gfp_t gfp);
7039
7040/**
7041 * cfg80211_connect_bss - notify cfg80211 of connection result
7042 *
7043 * @dev: network device
7044 * @bssid: the BSSID of the AP
7045 * @bss: Entry of bss to which STA got connected to, can be obtained through
7046 * cfg80211_get_bss() (may be %NULL). But it is recommended to store the
7047 * bss from the connect_request and hold a reference to it and return
7048 * through this param to avoid a warning if the bss is expired during the
7049 * connection, esp. for those drivers implementing connect op.
7050 * Only one parameter among @bssid and @bss needs to be specified.
7051 * @req_ie: association request IEs (maybe be %NULL)
7052 * @req_ie_len: association request IEs length
7053 * @resp_ie: association response IEs (may be %NULL)
7054 * @resp_ie_len: assoc response IEs length
7055 * @status: status code, %WLAN_STATUS_SUCCESS for successful connection, use
7056 * %WLAN_STATUS_UNSPECIFIED_FAILURE if your device cannot give you
7057 * the real status code for failures. If this call is used to report a
7058 * failure due to a timeout (e.g., not receiving an Authentication frame
7059 * from the AP) instead of an explicit rejection by the AP, -1 is used to
7060 * indicate that this is a failure, but without a status code.
7061 * @timeout_reason is used to report the reason for the timeout in that
7062 * case.
7063 * @gfp: allocation flags
7064 * @timeout_reason: reason for connection timeout. This is used when the
7065 * connection fails due to a timeout instead of an explicit rejection from
7066 * the AP. %NL80211_TIMEOUT_UNSPECIFIED is used when the timeout reason is
7067 * not known. This value is used only if @status < 0 to indicate that the
7068 * failure is due to a timeout and not due to explicit rejection by the AP.
7069 * This value is ignored in other cases (@status >= 0).
7070 *
7071 * It should be called by the underlying driver once execution of the connection
7072 * request from connect() has been completed. This is similar to
7073 * cfg80211_connect_result(), but with the option of identifying the exact bss
7074 * entry for the connection. Only one of the functions among
7075 * cfg80211_connect_bss(), cfg80211_connect_result(),
7076 * cfg80211_connect_timeout(), and cfg80211_connect_done() should be called.
7077 */
7078static inline void
7079cfg80211_connect_bss(struct net_device *dev, const u8 *bssid,
7080 struct cfg80211_bss *bss, const u8 *req_ie,
7081 size_t req_ie_len, const u8 *resp_ie,
7082 size_t resp_ie_len, int status, gfp_t gfp,
7083 enum nl80211_timeout_reason timeout_reason)
7084{
7085 struct cfg80211_connect_resp_params params;
7086
7087 memset(¶ms, 0, sizeof(params));
7088 params.status = status;
7089 params.bssid = bssid;
7090 params.bss = bss;
7091 params.req_ie = req_ie;
7092 params.req_ie_len = req_ie_len;
7093 params.resp_ie = resp_ie;
7094 params.resp_ie_len = resp_ie_len;
7095 params.timeout_reason = timeout_reason;
7096
7097 cfg80211_connect_done(dev, ¶ms, gfp);
7098}
7099
7100/**
7101 * cfg80211_connect_result - notify cfg80211 of connection result
7102 *
7103 * @dev: network device
7104 * @bssid: the BSSID of the AP
7105 * @req_ie: association request IEs (maybe be %NULL)
7106 * @req_ie_len: association request IEs length
7107 * @resp_ie: association response IEs (may be %NULL)
7108 * @resp_ie_len: assoc response IEs length
7109 * @status: status code, %WLAN_STATUS_SUCCESS for successful connection, use
7110 * %WLAN_STATUS_UNSPECIFIED_FAILURE if your device cannot give you
7111 * the real status code for failures.
7112 * @gfp: allocation flags
7113 *
7114 * It should be called by the underlying driver once execution of the connection
7115 * request from connect() has been completed. This is similar to
7116 * cfg80211_connect_bss() which allows the exact bss entry to be specified. Only
7117 * one of the functions among cfg80211_connect_bss(), cfg80211_connect_result(),
7118 * cfg80211_connect_timeout(), and cfg80211_connect_done() should be called.
7119 */
7120static inline void
7121cfg80211_connect_result(struct net_device *dev, const u8 *bssid,
7122 const u8 *req_ie, size_t req_ie_len,
7123 const u8 *resp_ie, size_t resp_ie_len,
7124 u16 status, gfp_t gfp)
7125{
7126 cfg80211_connect_bss(dev, bssid, NULL, req_ie, req_ie_len, resp_ie,
7127 resp_ie_len, status, gfp,
7128 NL80211_TIMEOUT_UNSPECIFIED);
7129}
7130
7131/**
7132 * cfg80211_connect_timeout - notify cfg80211 of connection timeout
7133 *
7134 * @dev: network device
7135 * @bssid: the BSSID of the AP
7136 * @req_ie: association request IEs (maybe be %NULL)
7137 * @req_ie_len: association request IEs length
7138 * @gfp: allocation flags
7139 * @timeout_reason: reason for connection timeout.
7140 *
7141 * It should be called by the underlying driver whenever connect() has failed
7142 * in a sequence where no explicit authentication/association rejection was
7143 * received from the AP. This could happen, e.g., due to not being able to send
7144 * out the Authentication or Association Request frame or timing out while
7145 * waiting for the response. Only one of the functions among
7146 * cfg80211_connect_bss(), cfg80211_connect_result(),
7147 * cfg80211_connect_timeout(), and cfg80211_connect_done() should be called.
7148 */
7149static inline void
7150cfg80211_connect_timeout(struct net_device *dev, const u8 *bssid,
7151 const u8 *req_ie, size_t req_ie_len, gfp_t gfp,
7152 enum nl80211_timeout_reason timeout_reason)
7153{
7154 cfg80211_connect_bss(dev, bssid, NULL, req_ie, req_ie_len, NULL, 0, -1,
7155 gfp, timeout_reason);
7156}
7157
7158/**
7159 * struct cfg80211_roam_info - driver initiated roaming information
7160 *
7161 * @channel: the channel of the new AP
7162 * @bss: entry of bss to which STA got roamed (may be %NULL if %bssid is set)
7163 * @bssid: the BSSID of the new AP (may be %NULL if %bss is set)
7164 * @req_ie: association request IEs (maybe be %NULL)
7165 * @req_ie_len: association request IEs length
7166 * @resp_ie: association response IEs (may be %NULL)
7167 * @resp_ie_len: assoc response IEs length
7168 * @fils: FILS related roaming information.
7169 */
7170struct cfg80211_roam_info {
7171 struct ieee80211_channel *channel;
7172 struct cfg80211_bss *bss;
7173 const u8 *bssid;
7174 const u8 *req_ie;
7175 size_t req_ie_len;
7176 const u8 *resp_ie;
7177 size_t resp_ie_len;
7178 struct cfg80211_fils_resp_params fils;
7179};
7180
7181/**
7182 * cfg80211_roamed - notify cfg80211 of roaming
7183 *
7184 * @dev: network device
7185 * @info: information about the new BSS. struct &cfg80211_roam_info.
7186 * @gfp: allocation flags
7187 *
7188 * This function may be called with the driver passing either the BSSID of the
7189 * new AP or passing the bss entry to avoid a race in timeout of the bss entry.
7190 * It should be called by the underlying driver whenever it roamed from one AP
7191 * to another while connected. Drivers which have roaming implemented in
7192 * firmware should pass the bss entry to avoid a race in bss entry timeout where
7193 * the bss entry of the new AP is seen in the driver, but gets timed out by the
7194 * time it is accessed in __cfg80211_roamed() due to delay in scheduling
7195 * rdev->event_work. In case of any failures, the reference is released
7196 * either in cfg80211_roamed() or in __cfg80211_romed(), Otherwise, it will be
7197 * released while disconnecting from the current bss.
7198 */
7199void cfg80211_roamed(struct net_device *dev, struct cfg80211_roam_info *info,
7200 gfp_t gfp);
7201
7202/**
7203 * cfg80211_port_authorized - notify cfg80211 of successful security association
7204 *
7205 * @dev: network device
7206 * @bssid: the BSSID of the AP
7207 * @gfp: allocation flags
7208 *
7209 * This function should be called by a driver that supports 4 way handshake
7210 * offload after a security association was successfully established (i.e.,
7211 * the 4 way handshake was completed successfully). The call to this function
7212 * should be preceded with a call to cfg80211_connect_result(),
7213 * cfg80211_connect_done(), cfg80211_connect_bss() or cfg80211_roamed() to
7214 * indicate the 802.11 association.
7215 */
7216void cfg80211_port_authorized(struct net_device *dev, const u8 *bssid,
7217 gfp_t gfp);
7218
7219/**
7220 * cfg80211_disconnected - notify cfg80211 that connection was dropped
7221 *
7222 * @dev: network device
7223 * @ie: information elements of the deauth/disassoc frame (may be %NULL)
7224 * @ie_len: length of IEs
7225 * @reason: reason code for the disconnection, set it to 0 if unknown
7226 * @locally_generated: disconnection was requested locally
7227 * @gfp: allocation flags
7228 *
7229 * After it calls this function, the driver should enter an idle state
7230 * and not try to connect to any AP any more.
7231 */
7232void cfg80211_disconnected(struct net_device *dev, u16 reason,
7233 const u8 *ie, size_t ie_len,
7234 bool locally_generated, gfp_t gfp);
7235
7236/**
7237 * cfg80211_ready_on_channel - notification of remain_on_channel start
7238 * @wdev: wireless device
7239 * @cookie: the request cookie
7240 * @chan: The current channel (from remain_on_channel request)
7241 * @duration: Duration in milliseconds that the driver intents to remain on the
7242 * channel
7243 * @gfp: allocation flags
7244 */
7245void cfg80211_ready_on_channel(struct wireless_dev *wdev, u64 cookie,
7246 struct ieee80211_channel *chan,
7247 unsigned int duration, gfp_t gfp);
7248
7249/**
7250 * cfg80211_remain_on_channel_expired - remain_on_channel duration expired
7251 * @wdev: wireless device
7252 * @cookie: the request cookie
7253 * @chan: The current channel (from remain_on_channel request)
7254 * @gfp: allocation flags
7255 */
7256void cfg80211_remain_on_channel_expired(struct wireless_dev *wdev, u64 cookie,
7257 struct ieee80211_channel *chan,
7258 gfp_t gfp);
7259
7260/**
7261 * cfg80211_tx_mgmt_expired - tx_mgmt duration expired
7262 * @wdev: wireless device
7263 * @cookie: the requested cookie
7264 * @chan: The current channel (from tx_mgmt request)
7265 * @gfp: allocation flags
7266 */
7267void cfg80211_tx_mgmt_expired(struct wireless_dev *wdev, u64 cookie,
7268 struct ieee80211_channel *chan, gfp_t gfp);
7269
7270/**
7271 * cfg80211_sinfo_alloc_tid_stats - allocate per-tid statistics.
7272 *
7273 * @sinfo: the station information
7274 * @gfp: allocation flags
7275 */
7276int cfg80211_sinfo_alloc_tid_stats(struct station_info *sinfo, gfp_t gfp);
7277
7278/**
7279 * cfg80211_sinfo_release_content - release contents of station info
7280 * @sinfo: the station information
7281 *
7282 * Releases any potentially allocated sub-information of the station
7283 * information, but not the struct itself (since it's typically on
7284 * the stack.)
7285 */
7286static inline void cfg80211_sinfo_release_content(struct station_info *sinfo)
7287{
7288 kfree(sinfo->pertid);
7289}
7290
7291/**
7292 * cfg80211_new_sta - notify userspace about station
7293 *
7294 * @dev: the netdev
7295 * @mac_addr: the station's address
7296 * @sinfo: the station information
7297 * @gfp: allocation flags
7298 */
7299void cfg80211_new_sta(struct net_device *dev, const u8 *mac_addr,
7300 struct station_info *sinfo, gfp_t gfp);
7301
7302/**
7303 * cfg80211_del_sta_sinfo - notify userspace about deletion of a station
7304 * @dev: the netdev
7305 * @mac_addr: the station's address
7306 * @sinfo: the station information/statistics
7307 * @gfp: allocation flags
7308 */
7309void cfg80211_del_sta_sinfo(struct net_device *dev, const u8 *mac_addr,
7310 struct station_info *sinfo, gfp_t gfp);
7311
7312/**
7313 * cfg80211_del_sta - notify userspace about deletion of a station
7314 *
7315 * @dev: the netdev
7316 * @mac_addr: the station's address
7317 * @gfp: allocation flags
7318 */
7319static inline void cfg80211_del_sta(struct net_device *dev,
7320 const u8 *mac_addr, gfp_t gfp)
7321{
7322 cfg80211_del_sta_sinfo(dev, mac_addr, NULL, gfp);
7323}
7324
7325/**
7326 * cfg80211_conn_failed - connection request failed notification
7327 *
7328 * @dev: the netdev
7329 * @mac_addr: the station's address
7330 * @reason: the reason for connection failure
7331 * @gfp: allocation flags
7332 *
7333 * Whenever a station tries to connect to an AP and if the station
7334 * could not connect to the AP as the AP has rejected the connection
7335 * for some reasons, this function is called.
7336 *
7337 * The reason for connection failure can be any of the value from
7338 * nl80211_connect_failed_reason enum
7339 */
7340void cfg80211_conn_failed(struct net_device *dev, const u8 *mac_addr,
7341 enum nl80211_connect_failed_reason reason,
7342 gfp_t gfp);
7343
7344/**
7345 * cfg80211_rx_mgmt_khz - notification of received, unprocessed management frame
7346 * @wdev: wireless device receiving the frame
7347 * @freq: Frequency on which the frame was received in KHz
7348 * @sig_dbm: signal strength in dBm, or 0 if unknown
7349 * @buf: Management frame (header + body)
7350 * @len: length of the frame data
7351 * @flags: flags, as defined in enum nl80211_rxmgmt_flags
7352 *
7353 * This function is called whenever an Action frame is received for a station
7354 * mode interface, but is not processed in kernel.
7355 *
7356 * Return: %true if a user space application has registered for this frame.
7357 * For action frames, that makes it responsible for rejecting unrecognized
7358 * action frames; %false otherwise, in which case for action frames the
7359 * driver is responsible for rejecting the frame.
7360 */
7361bool cfg80211_rx_mgmt_khz(struct wireless_dev *wdev, int freq, int sig_dbm,
7362 const u8 *buf, size_t len, u32 flags);
7363
7364/**
7365 * cfg80211_rx_mgmt - notification of received, unprocessed management frame
7366 * @wdev: wireless device receiving the frame
7367 * @freq: Frequency on which the frame was received in MHz
7368 * @sig_dbm: signal strength in dBm, or 0 if unknown
7369 * @buf: Management frame (header + body)
7370 * @len: length of the frame data
7371 * @flags: flags, as defined in enum nl80211_rxmgmt_flags
7372 *
7373 * This function is called whenever an Action frame is received for a station
7374 * mode interface, but is not processed in kernel.
7375 *
7376 * Return: %true if a user space application has registered for this frame.
7377 * For action frames, that makes it responsible for rejecting unrecognized
7378 * action frames; %false otherwise, in which case for action frames the
7379 * driver is responsible for rejecting the frame.
7380 */
7381static inline bool cfg80211_rx_mgmt(struct wireless_dev *wdev, int freq,
7382 int sig_dbm, const u8 *buf, size_t len,
7383 u32 flags)
7384{
7385 return cfg80211_rx_mgmt_khz(wdev, MHZ_TO_KHZ(freq), sig_dbm, buf, len,
7386 flags);
7387}
7388
7389/**
7390 * cfg80211_mgmt_tx_status - notification of TX status for management frame
7391 * @wdev: wireless device receiving the frame
7392 * @cookie: Cookie returned by cfg80211_ops::mgmt_tx()
7393 * @buf: Management frame (header + body)
7394 * @len: length of the frame data
7395 * @ack: Whether frame was acknowledged
7396 * @gfp: context flags
7397 *
7398 * This function is called whenever a management frame was requested to be
7399 * transmitted with cfg80211_ops::mgmt_tx() to report the TX status of the
7400 * transmission attempt.
7401 */
7402void cfg80211_mgmt_tx_status(struct wireless_dev *wdev, u64 cookie,
7403 const u8 *buf, size_t len, bool ack, gfp_t gfp);
7404
7405/**
7406 * cfg80211_control_port_tx_status - notification of TX status for control
7407 * port frames
7408 * @wdev: wireless device receiving the frame
7409 * @cookie: Cookie returned by cfg80211_ops::tx_control_port()
7410 * @buf: Data frame (header + body)
7411 * @len: length of the frame data
7412 * @ack: Whether frame was acknowledged
7413 * @gfp: context flags
7414 *
7415 * This function is called whenever a control port frame was requested to be
7416 * transmitted with cfg80211_ops::tx_control_port() to report the TX status of
7417 * the transmission attempt.
7418 */
7419void cfg80211_control_port_tx_status(struct wireless_dev *wdev, u64 cookie,
7420 const u8 *buf, size_t len, bool ack,
7421 gfp_t gfp);
7422
7423/**
7424 * cfg80211_rx_control_port - notification about a received control port frame
7425 * @dev: The device the frame matched to
7426 * @skb: The skbuf with the control port frame. It is assumed that the skbuf
7427 * is 802.3 formatted (with 802.3 header). The skb can be non-linear.
7428 * This function does not take ownership of the skb, so the caller is
7429 * responsible for any cleanup. The caller must also ensure that
7430 * skb->protocol is set appropriately.
7431 * @unencrypted: Whether the frame was received unencrypted
7432 *
7433 * This function is used to inform userspace about a received control port
7434 * frame. It should only be used if userspace indicated it wants to receive
7435 * control port frames over nl80211.
7436 *
7437 * The frame is the data portion of the 802.3 or 802.11 data frame with all
7438 * network layer headers removed (e.g. the raw EAPoL frame).
7439 *
7440 * Return: %true if the frame was passed to userspace
7441 */
7442bool cfg80211_rx_control_port(struct net_device *dev,
7443 struct sk_buff *skb, bool unencrypted);
7444
7445/**
7446 * cfg80211_cqm_rssi_notify - connection quality monitoring rssi event
7447 * @dev: network device
7448 * @rssi_event: the triggered RSSI event
7449 * @rssi_level: new RSSI level value or 0 if not available
7450 * @gfp: context flags
7451 *
7452 * This function is called when a configured connection quality monitoring
7453 * rssi threshold reached event occurs.
7454 */
7455void cfg80211_cqm_rssi_notify(struct net_device *dev,
7456 enum nl80211_cqm_rssi_threshold_event rssi_event,
7457 s32 rssi_level, gfp_t gfp);
7458
7459/**
7460 * cfg80211_cqm_pktloss_notify - notify userspace about packetloss to peer
7461 * @dev: network device
7462 * @peer: peer's MAC address
7463 * @num_packets: how many packets were lost -- should be a fixed threshold
7464 * but probably no less than maybe 50, or maybe a throughput dependent
7465 * threshold (to account for temporary interference)
7466 * @gfp: context flags
7467 */
7468void cfg80211_cqm_pktloss_notify(struct net_device *dev,
7469 const u8 *peer, u32 num_packets, gfp_t gfp);
7470
7471/**
7472 * cfg80211_cqm_txe_notify - TX error rate event
7473 * @dev: network device
7474 * @peer: peer's MAC address
7475 * @num_packets: how many packets were lost
7476 * @rate: % of packets which failed transmission
7477 * @intvl: interval (in s) over which the TX failure threshold was breached.
7478 * @gfp: context flags
7479 *
7480 * Notify userspace when configured % TX failures over number of packets in a
7481 * given interval is exceeded.
7482 */
7483void cfg80211_cqm_txe_notify(struct net_device *dev, const u8 *peer,
7484 u32 num_packets, u32 rate, u32 intvl, gfp_t gfp);
7485
7486/**
7487 * cfg80211_cqm_beacon_loss_notify - beacon loss event
7488 * @dev: network device
7489 * @gfp: context flags
7490 *
7491 * Notify userspace about beacon loss from the connected AP.
7492 */
7493void cfg80211_cqm_beacon_loss_notify(struct net_device *dev, gfp_t gfp);
7494
7495/**
7496 * cfg80211_radar_event - radar detection event
7497 * @wiphy: the wiphy
7498 * @chandef: chandef for the current channel
7499 * @gfp: context flags
7500 *
7501 * This function is called when a radar is detected on the current chanenl.
7502 */
7503void cfg80211_radar_event(struct wiphy *wiphy,
7504 struct cfg80211_chan_def *chandef, gfp_t gfp);
7505
7506/**
7507 * cfg80211_sta_opmode_change_notify - STA's ht/vht operation mode change event
7508 * @dev: network device
7509 * @mac: MAC address of a station which opmode got modified
7510 * @sta_opmode: station's current opmode value
7511 * @gfp: context flags
7512 *
7513 * Driver should call this function when station's opmode modified via action
7514 * frame.
7515 */
7516void cfg80211_sta_opmode_change_notify(struct net_device *dev, const u8 *mac,
7517 struct sta_opmode_info *sta_opmode,
7518 gfp_t gfp);
7519
7520/**
7521 * cfg80211_cac_event - Channel availability check (CAC) event
7522 * @netdev: network device
7523 * @chandef: chandef for the current channel
7524 * @event: type of event
7525 * @gfp: context flags
7526 *
7527 * This function is called when a Channel availability check (CAC) is finished
7528 * or aborted. This must be called to notify the completion of a CAC process,
7529 * also by full-MAC drivers.
7530 */
7531void cfg80211_cac_event(struct net_device *netdev,
7532 const struct cfg80211_chan_def *chandef,
7533 enum nl80211_radar_event event, gfp_t gfp);
7534
7535
7536/**
7537 * cfg80211_gtk_rekey_notify - notify userspace about driver rekeying
7538 * @dev: network device
7539 * @bssid: BSSID of AP (to avoid races)
7540 * @replay_ctr: new replay counter
7541 * @gfp: allocation flags
7542 */
7543void cfg80211_gtk_rekey_notify(struct net_device *dev, const u8 *bssid,
7544 const u8 *replay_ctr, gfp_t gfp);
7545
7546/**
7547 * cfg80211_pmksa_candidate_notify - notify about PMKSA caching candidate
7548 * @dev: network device
7549 * @index: candidate index (the smaller the index, the higher the priority)
7550 * @bssid: BSSID of AP
7551 * @preauth: Whether AP advertises support for RSN pre-authentication
7552 * @gfp: allocation flags
7553 */
7554void cfg80211_pmksa_candidate_notify(struct net_device *dev, int index,
7555 const u8 *bssid, bool preauth, gfp_t gfp);
7556
7557/**
7558 * cfg80211_rx_spurious_frame - inform userspace about a spurious frame
7559 * @dev: The device the frame matched to
7560 * @addr: the transmitter address
7561 * @gfp: context flags
7562 *
7563 * This function is used in AP mode (only!) to inform userspace that
7564 * a spurious class 3 frame was received, to be able to deauth the
7565 * sender.
7566 * Return: %true if the frame was passed to userspace (or this failed
7567 * for a reason other than not having a subscription.)
7568 */
7569bool cfg80211_rx_spurious_frame(struct net_device *dev,
7570 const u8 *addr, gfp_t gfp);
7571
7572/**
7573 * cfg80211_rx_unexpected_4addr_frame - inform about unexpected WDS frame
7574 * @dev: The device the frame matched to
7575 * @addr: the transmitter address
7576 * @gfp: context flags
7577 *
7578 * This function is used in AP mode (only!) to inform userspace that
7579 * an associated station sent a 4addr frame but that wasn't expected.
7580 * It is allowed and desirable to send this event only once for each
7581 * station to avoid event flooding.
7582 * Return: %true if the frame was passed to userspace (or this failed
7583 * for a reason other than not having a subscription.)
7584 */
7585bool cfg80211_rx_unexpected_4addr_frame(struct net_device *dev,
7586 const u8 *addr, gfp_t gfp);
7587
7588/**
7589 * cfg80211_probe_status - notify userspace about probe status
7590 * @dev: the device the probe was sent on
7591 * @addr: the address of the peer
7592 * @cookie: the cookie filled in @probe_client previously
7593 * @acked: indicates whether probe was acked or not
7594 * @ack_signal: signal strength (in dBm) of the ACK frame.
7595 * @is_valid_ack_signal: indicates the ack_signal is valid or not.
7596 * @gfp: allocation flags
7597 */
7598void cfg80211_probe_status(struct net_device *dev, const u8 *addr,
7599 u64 cookie, bool acked, s32 ack_signal,
7600 bool is_valid_ack_signal, gfp_t gfp);
7601
7602/**
7603 * cfg80211_report_obss_beacon_khz - report beacon from other APs
7604 * @wiphy: The wiphy that received the beacon
7605 * @frame: the frame
7606 * @len: length of the frame
7607 * @freq: frequency the frame was received on in KHz
7608 * @sig_dbm: signal strength in dBm, or 0 if unknown
7609 *
7610 * Use this function to report to userspace when a beacon was
7611 * received. It is not useful to call this when there is no
7612 * netdev that is in AP/GO mode.
7613 */
7614void cfg80211_report_obss_beacon_khz(struct wiphy *wiphy, const u8 *frame,
7615 size_t len, int freq, int sig_dbm);
7616
7617/**
7618 * cfg80211_report_obss_beacon - report beacon from other APs
7619 * @wiphy: The wiphy that received the beacon
7620 * @frame: the frame
7621 * @len: length of the frame
7622 * @freq: frequency the frame was received on
7623 * @sig_dbm: signal strength in dBm, or 0 if unknown
7624 *
7625 * Use this function to report to userspace when a beacon was
7626 * received. It is not useful to call this when there is no
7627 * netdev that is in AP/GO mode.
7628 */
7629static inline void cfg80211_report_obss_beacon(struct wiphy *wiphy,
7630 const u8 *frame, size_t len,
7631 int freq, int sig_dbm)
7632{
7633 cfg80211_report_obss_beacon_khz(wiphy, frame, len, MHZ_TO_KHZ(freq),
7634 sig_dbm);
7635}
7636
7637/**
7638 * cfg80211_reg_can_beacon - check if beaconing is allowed
7639 * @wiphy: the wiphy
7640 * @chandef: the channel definition
7641 * @iftype: interface type
7642 *
7643 * Return: %true if there is no secondary channel or the secondary channel(s)
7644 * can be used for beaconing (i.e. is not a radar channel etc.)
7645 */
7646bool cfg80211_reg_can_beacon(struct wiphy *wiphy,
7647 struct cfg80211_chan_def *chandef,
7648 enum nl80211_iftype iftype);
7649
7650/**
7651 * cfg80211_reg_can_beacon_relax - check if beaconing is allowed with relaxation
7652 * @wiphy: the wiphy
7653 * @chandef: the channel definition
7654 * @iftype: interface type
7655 *
7656 * Return: %true if there is no secondary channel or the secondary channel(s)
7657 * can be used for beaconing (i.e. is not a radar channel etc.). This version
7658 * also checks if IR-relaxation conditions apply, to allow beaconing under
7659 * more permissive conditions.
7660 *
7661 * Requires the wiphy mutex to be held.
7662 */
7663bool cfg80211_reg_can_beacon_relax(struct wiphy *wiphy,
7664 struct cfg80211_chan_def *chandef,
7665 enum nl80211_iftype iftype);
7666
7667/*
7668 * cfg80211_ch_switch_notify - update wdev channel and notify userspace
7669 * @dev: the device which switched channels
7670 * @chandef: the new channel definition
7671 *
7672 * Caller must acquire wdev_lock, therefore must only be called from sleepable
7673 * driver context!
7674 */
7675void cfg80211_ch_switch_notify(struct net_device *dev,
7676 struct cfg80211_chan_def *chandef);
7677
7678/*
7679 * cfg80211_ch_switch_started_notify - notify channel switch start
7680 * @dev: the device on which the channel switch started
7681 * @chandef: the future channel definition
7682 * @count: the number of TBTTs until the channel switch happens
7683 * @quiet: whether or not immediate quiet was requested by the AP
7684 *
7685 * Inform the userspace about the channel switch that has just
7686 * started, so that it can take appropriate actions (eg. starting
7687 * channel switch on other vifs), if necessary.
7688 */
7689void cfg80211_ch_switch_started_notify(struct net_device *dev,
7690 struct cfg80211_chan_def *chandef,
7691 u8 count, bool quiet);
7692
7693/**
7694 * ieee80211_operating_class_to_band - convert operating class to band
7695 *
7696 * @operating_class: the operating class to convert
7697 * @band: band pointer to fill
7698 *
7699 * Returns %true if the conversion was successful, %false otherwise.
7700 */
7701bool ieee80211_operating_class_to_band(u8 operating_class,
7702 enum nl80211_band *band);
7703
7704/**
7705 * ieee80211_chandef_to_operating_class - convert chandef to operation class
7706 *
7707 * @chandef: the chandef to convert
7708 * @op_class: a pointer to the resulting operating class
7709 *
7710 * Returns %true if the conversion was successful, %false otherwise.
7711 */
7712bool ieee80211_chandef_to_operating_class(struct cfg80211_chan_def *chandef,
7713 u8 *op_class);
7714
7715/**
7716 * ieee80211_chandef_to_khz - convert chandef to frequency in KHz
7717 *
7718 * @chandef: the chandef to convert
7719 *
7720 * Returns the center frequency of chandef (1st segment) in KHz.
7721 */
7722static inline u32
7723ieee80211_chandef_to_khz(const struct cfg80211_chan_def *chandef)
7724{
7725 return MHZ_TO_KHZ(chandef->center_freq1) + chandef->freq1_offset;
7726}
7727
7728/*
7729 * cfg80211_tdls_oper_request - request userspace to perform TDLS operation
7730 * @dev: the device on which the operation is requested
7731 * @peer: the MAC address of the peer device
7732 * @oper: the requested TDLS operation (NL80211_TDLS_SETUP or
7733 * NL80211_TDLS_TEARDOWN)
7734 * @reason_code: the reason code for teardown request
7735 * @gfp: allocation flags
7736 *
7737 * This function is used to request userspace to perform TDLS operation that
7738 * requires knowledge of keys, i.e., link setup or teardown when the AP
7739 * connection uses encryption. This is optional mechanism for the driver to use
7740 * if it can automatically determine when a TDLS link could be useful (e.g.,
7741 * based on traffic and signal strength for a peer).
7742 */
7743void cfg80211_tdls_oper_request(struct net_device *dev, const u8 *peer,
7744 enum nl80211_tdls_operation oper,
7745 u16 reason_code, gfp_t gfp);
7746
7747/*
7748 * cfg80211_calculate_bitrate - calculate actual bitrate (in 100Kbps units)
7749 * @rate: given rate_info to calculate bitrate from
7750 *
7751 * return 0 if MCS index >= 32
7752 */
7753u32 cfg80211_calculate_bitrate(struct rate_info *rate);
7754
7755/**
7756 * cfg80211_unregister_wdev - remove the given wdev
7757 * @wdev: struct wireless_dev to remove
7758 *
7759 * This function removes the device so it can no longer be used. It is necessary
7760 * to call this function even when cfg80211 requests the removal of the device
7761 * by calling the del_virtual_intf() callback. The function must also be called
7762 * when the driver wishes to unregister the wdev, e.g. when the hardware device
7763 * is unbound from the driver.
7764 *
7765 * Requires the RTNL and wiphy mutex to be held.
7766 */
7767void cfg80211_unregister_wdev(struct wireless_dev *wdev);
7768
7769/**
7770 * cfg80211_register_netdevice - register the given netdev
7771 * @dev: the netdev to register
7772 *
7773 * Note: In contexts coming from cfg80211 callbacks, you must call this rather
7774 * than register_netdevice(), unregister_netdev() is impossible as the RTNL is
7775 * held. Otherwise, both register_netdevice() and register_netdev() are usable
7776 * instead as well.
7777 *
7778 * Requires the RTNL and wiphy mutex to be held.
7779 */
7780int cfg80211_register_netdevice(struct net_device *dev);
7781
7782/**
7783 * cfg80211_unregister_netdevice - unregister the given netdev
7784 * @dev: the netdev to register
7785 *
7786 * Note: In contexts coming from cfg80211 callbacks, you must call this rather
7787 * than unregister_netdevice(), unregister_netdev() is impossible as the RTNL
7788 * is held. Otherwise, both unregister_netdevice() and unregister_netdev() are
7789 * usable instead as well.
7790 *
7791 * Requires the RTNL and wiphy mutex to be held.
7792 */
7793static inline void cfg80211_unregister_netdevice(struct net_device *dev)
7794{
7795 cfg80211_unregister_wdev(dev->ieee80211_ptr);
7796}
7797
7798/**
7799 * struct cfg80211_ft_event_params - FT Information Elements
7800 * @ies: FT IEs
7801 * @ies_len: length of the FT IE in bytes
7802 * @target_ap: target AP's MAC address
7803 * @ric_ies: RIC IE
7804 * @ric_ies_len: length of the RIC IE in bytes
7805 */
7806struct cfg80211_ft_event_params {
7807 const u8 *ies;
7808 size_t ies_len;
7809 const u8 *target_ap;
7810 const u8 *ric_ies;
7811 size_t ric_ies_len;
7812};
7813
7814/**
7815 * cfg80211_ft_event - notify userspace about FT IE and RIC IE
7816 * @netdev: network device
7817 * @ft_event: IE information
7818 */
7819void cfg80211_ft_event(struct net_device *netdev,
7820 struct cfg80211_ft_event_params *ft_event);
7821
7822/**
7823 * cfg80211_get_p2p_attr - find and copy a P2P attribute from IE buffer
7824 * @ies: the input IE buffer
7825 * @len: the input length
7826 * @attr: the attribute ID to find
7827 * @buf: output buffer, can be %NULL if the data isn't needed, e.g.
7828 * if the function is only called to get the needed buffer size
7829 * @bufsize: size of the output buffer
7830 *
7831 * The function finds a given P2P attribute in the (vendor) IEs and
7832 * copies its contents to the given buffer.
7833 *
7834 * Return: A negative error code (-%EILSEQ or -%ENOENT) if the data is
7835 * malformed or the attribute can't be found (respectively), or the
7836 * length of the found attribute (which can be zero).
7837 */
7838int cfg80211_get_p2p_attr(const u8 *ies, unsigned int len,
7839 enum ieee80211_p2p_attr_id attr,
7840 u8 *buf, unsigned int bufsize);
7841
7842/**
7843 * ieee80211_ie_split_ric - split an IE buffer according to ordering (with RIC)
7844 * @ies: the IE buffer
7845 * @ielen: the length of the IE buffer
7846 * @ids: an array with element IDs that are allowed before
7847 * the split. A WLAN_EID_EXTENSION value means that the next
7848 * EID in the list is a sub-element of the EXTENSION IE.
7849 * @n_ids: the size of the element ID array
7850 * @after_ric: array IE types that come after the RIC element
7851 * @n_after_ric: size of the @after_ric array
7852 * @offset: offset where to start splitting in the buffer
7853 *
7854 * This function splits an IE buffer by updating the @offset
7855 * variable to point to the location where the buffer should be
7856 * split.
7857 *
7858 * It assumes that the given IE buffer is well-formed, this
7859 * has to be guaranteed by the caller!
7860 *
7861 * It also assumes that the IEs in the buffer are ordered
7862 * correctly, if not the result of using this function will not
7863 * be ordered correctly either, i.e. it does no reordering.
7864 *
7865 * The function returns the offset where the next part of the
7866 * buffer starts, which may be @ielen if the entire (remainder)
7867 * of the buffer should be used.
7868 */
7869size_t ieee80211_ie_split_ric(const u8 *ies, size_t ielen,
7870 const u8 *ids, int n_ids,
7871 const u8 *after_ric, int n_after_ric,
7872 size_t offset);
7873
7874/**
7875 * ieee80211_ie_split - split an IE buffer according to ordering
7876 * @ies: the IE buffer
7877 * @ielen: the length of the IE buffer
7878 * @ids: an array with element IDs that are allowed before
7879 * the split. A WLAN_EID_EXTENSION value means that the next
7880 * EID in the list is a sub-element of the EXTENSION IE.
7881 * @n_ids: the size of the element ID array
7882 * @offset: offset where to start splitting in the buffer
7883 *
7884 * This function splits an IE buffer by updating the @offset
7885 * variable to point to the location where the buffer should be
7886 * split.
7887 *
7888 * It assumes that the given IE buffer is well-formed, this
7889 * has to be guaranteed by the caller!
7890 *
7891 * It also assumes that the IEs in the buffer are ordered
7892 * correctly, if not the result of using this function will not
7893 * be ordered correctly either, i.e. it does no reordering.
7894 *
7895 * The function returns the offset where the next part of the
7896 * buffer starts, which may be @ielen if the entire (remainder)
7897 * of the buffer should be used.
7898 */
7899static inline size_t ieee80211_ie_split(const u8 *ies, size_t ielen,
7900 const u8 *ids, int n_ids, size_t offset)
7901{
7902 return ieee80211_ie_split_ric(ies, ielen, ids, n_ids, NULL, 0, offset);
7903}
7904
7905/**
7906 * cfg80211_report_wowlan_wakeup - report wakeup from WoWLAN
7907 * @wdev: the wireless device reporting the wakeup
7908 * @wakeup: the wakeup report
7909 * @gfp: allocation flags
7910 *
7911 * This function reports that the given device woke up. If it
7912 * caused the wakeup, report the reason(s), otherwise you may
7913 * pass %NULL as the @wakeup parameter to advertise that something
7914 * else caused the wakeup.
7915 */
7916void cfg80211_report_wowlan_wakeup(struct wireless_dev *wdev,
7917 struct cfg80211_wowlan_wakeup *wakeup,
7918 gfp_t gfp);
7919
7920/**
7921 * cfg80211_crit_proto_stopped() - indicate critical protocol stopped by driver.
7922 *
7923 * @wdev: the wireless device for which critical protocol is stopped.
7924 * @gfp: allocation flags
7925 *
7926 * This function can be called by the driver to indicate it has reverted
7927 * operation back to normal. One reason could be that the duration given
7928 * by .crit_proto_start() has expired.
7929 */
7930void cfg80211_crit_proto_stopped(struct wireless_dev *wdev, gfp_t gfp);
7931
7932/**
7933 * ieee80211_get_num_supported_channels - get number of channels device has
7934 * @wiphy: the wiphy
7935 *
7936 * Return: the number of channels supported by the device.
7937 */
7938unsigned int ieee80211_get_num_supported_channels(struct wiphy *wiphy);
7939
7940/**
7941 * cfg80211_check_combinations - check interface combinations
7942 *
7943 * @wiphy: the wiphy
7944 * @params: the interface combinations parameter
7945 *
7946 * This function can be called by the driver to check whether a
7947 * combination of interfaces and their types are allowed according to
7948 * the interface combinations.
7949 */
7950int cfg80211_check_combinations(struct wiphy *wiphy,
7951 struct iface_combination_params *params);
7952
7953/**
7954 * cfg80211_iter_combinations - iterate over matching combinations
7955 *
7956 * @wiphy: the wiphy
7957 * @params: the interface combinations parameter
7958 * @iter: function to call for each matching combination
7959 * @data: pointer to pass to iter function
7960 *
7961 * This function can be called by the driver to check what possible
7962 * combinations it fits in at a given moment, e.g. for channel switching
7963 * purposes.
7964 */
7965int cfg80211_iter_combinations(struct wiphy *wiphy,
7966 struct iface_combination_params *params,
7967 void (*iter)(const struct ieee80211_iface_combination *c,
7968 void *data),
7969 void *data);
7970
7971/*
7972 * cfg80211_stop_iface - trigger interface disconnection
7973 *
7974 * @wiphy: the wiphy
7975 * @wdev: wireless device
7976 * @gfp: context flags
7977 *
7978 * Trigger interface to be stopped as if AP was stopped, IBSS/mesh left, STA
7979 * disconnected.
7980 *
7981 * Note: This doesn't need any locks and is asynchronous.
7982 */
7983void cfg80211_stop_iface(struct wiphy *wiphy, struct wireless_dev *wdev,
7984 gfp_t gfp);
7985
7986/**
7987 * cfg80211_shutdown_all_interfaces - shut down all interfaces for a wiphy
7988 * @wiphy: the wiphy to shut down
7989 *
7990 * This function shuts down all interfaces belonging to this wiphy by
7991 * calling dev_close() (and treating non-netdev interfaces as needed).
7992 * It shouldn't really be used unless there are some fatal device errors
7993 * that really can't be recovered in any other way.
7994 *
7995 * Callers must hold the RTNL and be able to deal with callbacks into
7996 * the driver while the function is running.
7997 */
7998void cfg80211_shutdown_all_interfaces(struct wiphy *wiphy);
7999
8000/**
8001 * wiphy_ext_feature_set - set the extended feature flag
8002 *
8003 * @wiphy: the wiphy to modify.
8004 * @ftidx: extended feature bit index.
8005 *
8006 * The extended features are flagged in multiple bytes (see
8007 * &struct wiphy.@ext_features)
8008 */
8009static inline void wiphy_ext_feature_set(struct wiphy *wiphy,
8010 enum nl80211_ext_feature_index ftidx)
8011{
8012 u8 *ft_byte;
8013
8014 ft_byte = &wiphy->ext_features[ftidx / 8];
8015 *ft_byte |= BIT(ftidx % 8);
8016}
8017
8018/**
8019 * wiphy_ext_feature_isset - check the extended feature flag
8020 *
8021 * @wiphy: the wiphy to modify.
8022 * @ftidx: extended feature bit index.
8023 *
8024 * The extended features are flagged in multiple bytes (see
8025 * &struct wiphy.@ext_features)
8026 */
8027static inline bool
8028wiphy_ext_feature_isset(struct wiphy *wiphy,
8029 enum nl80211_ext_feature_index ftidx)
8030{
8031 u8 ft_byte;
8032
8033 ft_byte = wiphy->ext_features[ftidx / 8];
8034 return (ft_byte & BIT(ftidx % 8)) != 0;
8035}
8036
8037/**
8038 * cfg80211_free_nan_func - free NAN function
8039 * @f: NAN function that should be freed
8040 *
8041 * Frees all the NAN function and all it's allocated members.
8042 */
8043void cfg80211_free_nan_func(struct cfg80211_nan_func *f);
8044
8045/**
8046 * struct cfg80211_nan_match_params - NAN match parameters
8047 * @type: the type of the function that triggered a match. If it is
8048 * %NL80211_NAN_FUNC_SUBSCRIBE it means that we replied to a subscriber.
8049 * If it is %NL80211_NAN_FUNC_PUBLISH, it means that we got a discovery
8050 * result.
8051 * If it is %NL80211_NAN_FUNC_FOLLOW_UP, we received a follow up.
8052 * @inst_id: the local instance id
8053 * @peer_inst_id: the instance id of the peer's function
8054 * @addr: the MAC address of the peer
8055 * @info_len: the length of the &info
8056 * @info: the Service Specific Info from the peer (if any)
8057 * @cookie: unique identifier of the corresponding function
8058 */
8059struct cfg80211_nan_match_params {
8060 enum nl80211_nan_function_type type;
8061 u8 inst_id;
8062 u8 peer_inst_id;
8063 const u8 *addr;
8064 u8 info_len;
8065 const u8 *info;
8066 u64 cookie;
8067};
8068
8069/**
8070 * cfg80211_nan_match - report a match for a NAN function.
8071 * @wdev: the wireless device reporting the match
8072 * @match: match notification parameters
8073 * @gfp: allocation flags
8074 *
8075 * This function reports that the a NAN function had a match. This
8076 * can be a subscribe that had a match or a solicited publish that
8077 * was sent. It can also be a follow up that was received.
8078 */
8079void cfg80211_nan_match(struct wireless_dev *wdev,
8080 struct cfg80211_nan_match_params *match, gfp_t gfp);
8081
8082/**
8083 * cfg80211_nan_func_terminated - notify about NAN function termination.
8084 *
8085 * @wdev: the wireless device reporting the match
8086 * @inst_id: the local instance id
8087 * @reason: termination reason (one of the NL80211_NAN_FUNC_TERM_REASON_*)
8088 * @cookie: unique NAN function identifier
8089 * @gfp: allocation flags
8090 *
8091 * This function reports that the a NAN function is terminated.
8092 */
8093void cfg80211_nan_func_terminated(struct wireless_dev *wdev,
8094 u8 inst_id,
8095 enum nl80211_nan_func_term_reason reason,
8096 u64 cookie, gfp_t gfp);
8097
8098/* ethtool helper */
8099void cfg80211_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info);
8100
8101/**
8102 * cfg80211_external_auth_request - userspace request for authentication
8103 * @netdev: network device
8104 * @params: External authentication parameters
8105 * @gfp: allocation flags
8106 * Returns: 0 on success, < 0 on error
8107 */
8108int cfg80211_external_auth_request(struct net_device *netdev,
8109 struct cfg80211_external_auth_params *params,
8110 gfp_t gfp);
8111
8112/**
8113 * cfg80211_pmsr_report - report peer measurement result data
8114 * @wdev: the wireless device reporting the measurement
8115 * @req: the original measurement request
8116 * @result: the result data
8117 * @gfp: allocation flags
8118 */
8119void cfg80211_pmsr_report(struct wireless_dev *wdev,
8120 struct cfg80211_pmsr_request *req,
8121 struct cfg80211_pmsr_result *result,
8122 gfp_t gfp);
8123
8124/**
8125 * cfg80211_pmsr_complete - report peer measurement completed
8126 * @wdev: the wireless device reporting the measurement
8127 * @req: the original measurement request
8128 * @gfp: allocation flags
8129 *
8130 * Report that the entire measurement completed, after this
8131 * the request pointer will no longer be valid.
8132 */
8133void cfg80211_pmsr_complete(struct wireless_dev *wdev,
8134 struct cfg80211_pmsr_request *req,
8135 gfp_t gfp);
8136
8137/**
8138 * cfg80211_iftype_allowed - check whether the interface can be allowed
8139 * @wiphy: the wiphy
8140 * @iftype: interface type
8141 * @is_4addr: use_4addr flag, must be '0' when check_swif is '1'
8142 * @check_swif: check iftype against software interfaces
8143 *
8144 * Check whether the interface is allowed to operate; additionally, this API
8145 * can be used to check iftype against the software interfaces when
8146 * check_swif is '1'.
8147 */
8148bool cfg80211_iftype_allowed(struct wiphy *wiphy, enum nl80211_iftype iftype,
8149 bool is_4addr, u8 check_swif);
8150
8151
8152/* Logging, debugging and troubleshooting/diagnostic helpers. */
8153
8154/* wiphy_printk helpers, similar to dev_printk */
8155
8156#define wiphy_printk(level, wiphy, format, args...) \
8157 dev_printk(level, &(wiphy)->dev, format, ##args)
8158#define wiphy_emerg(wiphy, format, args...) \
8159 dev_emerg(&(wiphy)->dev, format, ##args)
8160#define wiphy_alert(wiphy, format, args...) \
8161 dev_alert(&(wiphy)->dev, format, ##args)
8162#define wiphy_crit(wiphy, format, args...) \
8163 dev_crit(&(wiphy)->dev, format, ##args)
8164#define wiphy_err(wiphy, format, args...) \
8165 dev_err(&(wiphy)->dev, format, ##args)
8166#define wiphy_warn(wiphy, format, args...) \
8167 dev_warn(&(wiphy)->dev, format, ##args)
8168#define wiphy_notice(wiphy, format, args...) \
8169 dev_notice(&(wiphy)->dev, format, ##args)
8170#define wiphy_info(wiphy, format, args...) \
8171 dev_info(&(wiphy)->dev, format, ##args)
8172#define wiphy_info_once(wiphy, format, args...) \
8173 dev_info_once(&(wiphy)->dev, format, ##args)
8174
8175#define wiphy_err_ratelimited(wiphy, format, args...) \
8176 dev_err_ratelimited(&(wiphy)->dev, format, ##args)
8177#define wiphy_warn_ratelimited(wiphy, format, args...) \
8178 dev_warn_ratelimited(&(wiphy)->dev, format, ##args)
8179
8180#define wiphy_debug(wiphy, format, args...) \
8181 wiphy_printk(KERN_DEBUG, wiphy, format, ##args)
8182
8183#define wiphy_dbg(wiphy, format, args...) \
8184 dev_dbg(&(wiphy)->dev, format, ##args)
8185
8186#if defined(VERBOSE_DEBUG)
8187#define wiphy_vdbg wiphy_dbg
8188#else
8189#define wiphy_vdbg(wiphy, format, args...) \
8190({ \
8191 if (0) \
8192 wiphy_printk(KERN_DEBUG, wiphy, format, ##args); \
8193 0; \
8194})
8195#endif
8196
8197/*
8198 * wiphy_WARN() acts like wiphy_printk(), but with the key difference
8199 * of using a WARN/WARN_ON to get the message out, including the
8200 * file/line information and a backtrace.
8201 */
8202#define wiphy_WARN(wiphy, format, args...) \
8203 WARN(1, "wiphy: %s\n" format, wiphy_name(wiphy), ##args);
8204
8205/**
8206 * cfg80211_update_owe_info_event - Notify the peer's OWE info to user space
8207 * @netdev: network device
8208 * @owe_info: peer's owe info
8209 * @gfp: allocation flags
8210 */
8211void cfg80211_update_owe_info_event(struct net_device *netdev,
8212 struct cfg80211_update_owe_info *owe_info,
8213 gfp_t gfp);
8214
8215/**
8216 * cfg80211_bss_flush - resets all the scan entries
8217 * @wiphy: the wiphy
8218 */
8219void cfg80211_bss_flush(struct wiphy *wiphy);
8220
8221#endif /* __NET_CFG80211_H */
1/* SPDX-License-Identifier: GPL-2.0-only */
2#ifndef __NET_CFG80211_H
3#define __NET_CFG80211_H
4/*
5 * 802.11 device and configuration interface
6 *
7 * Copyright 2006-2010 Johannes Berg <johannes@sipsolutions.net>
8 * Copyright 2013-2014 Intel Mobile Communications GmbH
9 * Copyright 2015-2017 Intel Deutschland GmbH
10 * Copyright (C) 2018-2024 Intel Corporation
11 */
12
13#include <linux/ethtool.h>
14#include <uapi/linux/rfkill.h>
15#include <linux/netdevice.h>
16#include <linux/debugfs.h>
17#include <linux/list.h>
18#include <linux/bug.h>
19#include <linux/netlink.h>
20#include <linux/skbuff.h>
21#include <linux/nl80211.h>
22#include <linux/if_ether.h>
23#include <linux/ieee80211.h>
24#include <linux/net.h>
25#include <linux/rfkill.h>
26#include <net/regulatory.h>
27
28/**
29 * DOC: Introduction
30 *
31 * cfg80211 is the configuration API for 802.11 devices in Linux. It bridges
32 * userspace and drivers, and offers some utility functionality associated
33 * with 802.11. cfg80211 must, directly or indirectly via mac80211, be used
34 * by all modern wireless drivers in Linux, so that they offer a consistent
35 * API through nl80211. For backward compatibility, cfg80211 also offers
36 * wireless extensions to userspace, but hides them from drivers completely.
37 *
38 * Additionally, cfg80211 contains code to help enforce regulatory spectrum
39 * use restrictions.
40 */
41
42
43/**
44 * DOC: Device registration
45 *
46 * In order for a driver to use cfg80211, it must register the hardware device
47 * with cfg80211. This happens through a number of hardware capability structs
48 * described below.
49 *
50 * The fundamental structure for each device is the 'wiphy', of which each
51 * instance describes a physical wireless device connected to the system. Each
52 * such wiphy can have zero, one, or many virtual interfaces associated with
53 * it, which need to be identified as such by pointing the network interface's
54 * @ieee80211_ptr pointer to a &struct wireless_dev which further describes
55 * the wireless part of the interface. Normally this struct is embedded in the
56 * network interface's private data area. Drivers can optionally allow creating
57 * or destroying virtual interfaces on the fly, but without at least one or the
58 * ability to create some the wireless device isn't useful.
59 *
60 * Each wiphy structure contains device capability information, and also has
61 * a pointer to the various operations the driver offers. The definitions and
62 * structures here describe these capabilities in detail.
63 */
64
65struct wiphy;
66
67/*
68 * wireless hardware capability structures
69 */
70
71/**
72 * enum ieee80211_channel_flags - channel flags
73 *
74 * Channel flags set by the regulatory control code.
75 *
76 * @IEEE80211_CHAN_DISABLED: This channel is disabled.
77 * @IEEE80211_CHAN_NO_IR: do not initiate radiation, this includes
78 * sending probe requests or beaconing.
79 * @IEEE80211_CHAN_PSD: Power spectral density (in dBm) is set for this
80 * channel.
81 * @IEEE80211_CHAN_RADAR: Radar detection is required on this channel.
82 * @IEEE80211_CHAN_NO_HT40PLUS: extension channel above this channel
83 * is not permitted.
84 * @IEEE80211_CHAN_NO_HT40MINUS: extension channel below this channel
85 * is not permitted.
86 * @IEEE80211_CHAN_NO_OFDM: OFDM is not allowed on this channel.
87 * @IEEE80211_CHAN_NO_80MHZ: If the driver supports 80 MHz on the band,
88 * this flag indicates that an 80 MHz channel cannot use this
89 * channel as the control or any of the secondary channels.
90 * This may be due to the driver or due to regulatory bandwidth
91 * restrictions.
92 * @IEEE80211_CHAN_NO_160MHZ: If the driver supports 160 MHz on the band,
93 * this flag indicates that an 160 MHz channel cannot use this
94 * channel as the control or any of the secondary channels.
95 * This may be due to the driver or due to regulatory bandwidth
96 * restrictions.
97 * @IEEE80211_CHAN_INDOOR_ONLY: see %NL80211_FREQUENCY_ATTR_INDOOR_ONLY
98 * @IEEE80211_CHAN_IR_CONCURRENT: see %NL80211_FREQUENCY_ATTR_IR_CONCURRENT
99 * @IEEE80211_CHAN_NO_20MHZ: 20 MHz bandwidth is not permitted
100 * on this channel.
101 * @IEEE80211_CHAN_NO_10MHZ: 10 MHz bandwidth is not permitted
102 * on this channel.
103 * @IEEE80211_CHAN_NO_HE: HE operation is not permitted on this channel.
104 * @IEEE80211_CHAN_1MHZ: 1 MHz bandwidth is permitted
105 * on this channel.
106 * @IEEE80211_CHAN_2MHZ: 2 MHz bandwidth is permitted
107 * on this channel.
108 * @IEEE80211_CHAN_4MHZ: 4 MHz bandwidth is permitted
109 * on this channel.
110 * @IEEE80211_CHAN_8MHZ: 8 MHz bandwidth is permitted
111 * on this channel.
112 * @IEEE80211_CHAN_16MHZ: 16 MHz bandwidth is permitted
113 * on this channel.
114 * @IEEE80211_CHAN_NO_320MHZ: If the driver supports 320 MHz on the band,
115 * this flag indicates that a 320 MHz channel cannot use this
116 * channel as the control or any of the secondary channels.
117 * This may be due to the driver or due to regulatory bandwidth
118 * restrictions.
119 * @IEEE80211_CHAN_NO_EHT: EHT operation is not permitted on this channel.
120 * @IEEE80211_CHAN_DFS_CONCURRENT: See %NL80211_RRF_DFS_CONCURRENT
121 * @IEEE80211_CHAN_NO_6GHZ_VLP_CLIENT: Client connection with VLP AP
122 * not permitted using this channel
123 * @IEEE80211_CHAN_NO_6GHZ_AFC_CLIENT: Client connection with AFC AP
124 * not permitted using this channel
125 * @IEEE80211_CHAN_CAN_MONITOR: This channel can be used for monitor
126 * mode even in the presence of other (regulatory) restrictions,
127 * even if it is otherwise disabled.
128 * @IEEE80211_CHAN_ALLOW_6GHZ_VLP_AP: Allow using this channel for AP operation
129 * with very low power (VLP), even if otherwise set to NO_IR.
130 */
131enum ieee80211_channel_flags {
132 IEEE80211_CHAN_DISABLED = BIT(0),
133 IEEE80211_CHAN_NO_IR = BIT(1),
134 IEEE80211_CHAN_PSD = BIT(2),
135 IEEE80211_CHAN_RADAR = BIT(3),
136 IEEE80211_CHAN_NO_HT40PLUS = BIT(4),
137 IEEE80211_CHAN_NO_HT40MINUS = BIT(5),
138 IEEE80211_CHAN_NO_OFDM = BIT(6),
139 IEEE80211_CHAN_NO_80MHZ = BIT(7),
140 IEEE80211_CHAN_NO_160MHZ = BIT(8),
141 IEEE80211_CHAN_INDOOR_ONLY = BIT(9),
142 IEEE80211_CHAN_IR_CONCURRENT = BIT(10),
143 IEEE80211_CHAN_NO_20MHZ = BIT(11),
144 IEEE80211_CHAN_NO_10MHZ = BIT(12),
145 IEEE80211_CHAN_NO_HE = BIT(13),
146 IEEE80211_CHAN_1MHZ = BIT(14),
147 IEEE80211_CHAN_2MHZ = BIT(15),
148 IEEE80211_CHAN_4MHZ = BIT(16),
149 IEEE80211_CHAN_8MHZ = BIT(17),
150 IEEE80211_CHAN_16MHZ = BIT(18),
151 IEEE80211_CHAN_NO_320MHZ = BIT(19),
152 IEEE80211_CHAN_NO_EHT = BIT(20),
153 IEEE80211_CHAN_DFS_CONCURRENT = BIT(21),
154 IEEE80211_CHAN_NO_6GHZ_VLP_CLIENT = BIT(22),
155 IEEE80211_CHAN_NO_6GHZ_AFC_CLIENT = BIT(23),
156 IEEE80211_CHAN_CAN_MONITOR = BIT(24),
157 IEEE80211_CHAN_ALLOW_6GHZ_VLP_AP = BIT(25),
158};
159
160#define IEEE80211_CHAN_NO_HT40 \
161 (IEEE80211_CHAN_NO_HT40PLUS | IEEE80211_CHAN_NO_HT40MINUS)
162
163#define IEEE80211_DFS_MIN_CAC_TIME_MS 60000
164#define IEEE80211_DFS_MIN_NOP_TIME_MS (30 * 60 * 1000)
165
166/**
167 * struct ieee80211_channel - channel definition
168 *
169 * This structure describes a single channel for use
170 * with cfg80211.
171 *
172 * @center_freq: center frequency in MHz
173 * @freq_offset: offset from @center_freq, in KHz
174 * @hw_value: hardware-specific value for the channel
175 * @flags: channel flags from &enum ieee80211_channel_flags.
176 * @orig_flags: channel flags at registration time, used by regulatory
177 * code to support devices with additional restrictions
178 * @band: band this channel belongs to.
179 * @max_antenna_gain: maximum antenna gain in dBi
180 * @max_power: maximum transmission power (in dBm)
181 * @max_reg_power: maximum regulatory transmission power (in dBm)
182 * @beacon_found: helper to regulatory code to indicate when a beacon
183 * has been found on this channel. Use regulatory_hint_found_beacon()
184 * to enable this, this is useful only on 5 GHz band.
185 * @orig_mag: internal use
186 * @orig_mpwr: internal use
187 * @dfs_state: current state of this channel. Only relevant if radar is required
188 * on this channel.
189 * @dfs_state_entered: timestamp (jiffies) when the dfs state was entered.
190 * @dfs_cac_ms: DFS CAC time in milliseconds, this is valid for DFS channels.
191 * @psd: power spectral density (in dBm)
192 */
193struct ieee80211_channel {
194 enum nl80211_band band;
195 u32 center_freq;
196 u16 freq_offset;
197 u16 hw_value;
198 u32 flags;
199 int max_antenna_gain;
200 int max_power;
201 int max_reg_power;
202 bool beacon_found;
203 u32 orig_flags;
204 int orig_mag, orig_mpwr;
205 enum nl80211_dfs_state dfs_state;
206 unsigned long dfs_state_entered;
207 unsigned int dfs_cac_ms;
208 s8 psd;
209};
210
211/**
212 * enum ieee80211_rate_flags - rate flags
213 *
214 * Hardware/specification flags for rates. These are structured
215 * in a way that allows using the same bitrate structure for
216 * different bands/PHY modes.
217 *
218 * @IEEE80211_RATE_SHORT_PREAMBLE: Hardware can send with short
219 * preamble on this bitrate; only relevant in 2.4GHz band and
220 * with CCK rates.
221 * @IEEE80211_RATE_MANDATORY_A: This bitrate is a mandatory rate
222 * when used with 802.11a (on the 5 GHz band); filled by the
223 * core code when registering the wiphy.
224 * @IEEE80211_RATE_MANDATORY_B: This bitrate is a mandatory rate
225 * when used with 802.11b (on the 2.4 GHz band); filled by the
226 * core code when registering the wiphy.
227 * @IEEE80211_RATE_MANDATORY_G: This bitrate is a mandatory rate
228 * when used with 802.11g (on the 2.4 GHz band); filled by the
229 * core code when registering the wiphy.
230 * @IEEE80211_RATE_ERP_G: This is an ERP rate in 802.11g mode.
231 * @IEEE80211_RATE_SUPPORTS_5MHZ: Rate can be used in 5 MHz mode
232 * @IEEE80211_RATE_SUPPORTS_10MHZ: Rate can be used in 10 MHz mode
233 */
234enum ieee80211_rate_flags {
235 IEEE80211_RATE_SHORT_PREAMBLE = BIT(0),
236 IEEE80211_RATE_MANDATORY_A = BIT(1),
237 IEEE80211_RATE_MANDATORY_B = BIT(2),
238 IEEE80211_RATE_MANDATORY_G = BIT(3),
239 IEEE80211_RATE_ERP_G = BIT(4),
240 IEEE80211_RATE_SUPPORTS_5MHZ = BIT(5),
241 IEEE80211_RATE_SUPPORTS_10MHZ = BIT(6),
242};
243
244/**
245 * enum ieee80211_bss_type - BSS type filter
246 *
247 * @IEEE80211_BSS_TYPE_ESS: Infrastructure BSS
248 * @IEEE80211_BSS_TYPE_PBSS: Personal BSS
249 * @IEEE80211_BSS_TYPE_IBSS: Independent BSS
250 * @IEEE80211_BSS_TYPE_MBSS: Mesh BSS
251 * @IEEE80211_BSS_TYPE_ANY: Wildcard value for matching any BSS type
252 */
253enum ieee80211_bss_type {
254 IEEE80211_BSS_TYPE_ESS,
255 IEEE80211_BSS_TYPE_PBSS,
256 IEEE80211_BSS_TYPE_IBSS,
257 IEEE80211_BSS_TYPE_MBSS,
258 IEEE80211_BSS_TYPE_ANY
259};
260
261/**
262 * enum ieee80211_privacy - BSS privacy filter
263 *
264 * @IEEE80211_PRIVACY_ON: privacy bit set
265 * @IEEE80211_PRIVACY_OFF: privacy bit clear
266 * @IEEE80211_PRIVACY_ANY: Wildcard value for matching any privacy setting
267 */
268enum ieee80211_privacy {
269 IEEE80211_PRIVACY_ON,
270 IEEE80211_PRIVACY_OFF,
271 IEEE80211_PRIVACY_ANY
272};
273
274#define IEEE80211_PRIVACY(x) \
275 ((x) ? IEEE80211_PRIVACY_ON : IEEE80211_PRIVACY_OFF)
276
277/**
278 * struct ieee80211_rate - bitrate definition
279 *
280 * This structure describes a bitrate that an 802.11 PHY can
281 * operate with. The two values @hw_value and @hw_value_short
282 * are only for driver use when pointers to this structure are
283 * passed around.
284 *
285 * @flags: rate-specific flags from &enum ieee80211_rate_flags
286 * @bitrate: bitrate in units of 100 Kbps
287 * @hw_value: driver/hardware value for this rate
288 * @hw_value_short: driver/hardware value for this rate when
289 * short preamble is used
290 */
291struct ieee80211_rate {
292 u32 flags;
293 u16 bitrate;
294 u16 hw_value, hw_value_short;
295};
296
297/**
298 * struct ieee80211_he_obss_pd - AP settings for spatial reuse
299 *
300 * @enable: is the feature enabled.
301 * @sr_ctrl: The SR Control field of SRP element.
302 * @non_srg_max_offset: non-SRG maximum tx power offset
303 * @min_offset: minimal tx power offset an associated station shall use
304 * @max_offset: maximum tx power offset an associated station shall use
305 * @bss_color_bitmap: bitmap that indicates the BSS color values used by
306 * members of the SRG
307 * @partial_bssid_bitmap: bitmap that indicates the partial BSSID values
308 * used by members of the SRG
309 */
310struct ieee80211_he_obss_pd {
311 bool enable;
312 u8 sr_ctrl;
313 u8 non_srg_max_offset;
314 u8 min_offset;
315 u8 max_offset;
316 u8 bss_color_bitmap[8];
317 u8 partial_bssid_bitmap[8];
318};
319
320/**
321 * struct cfg80211_he_bss_color - AP settings for BSS coloring
322 *
323 * @color: the current color.
324 * @enabled: HE BSS color is used
325 * @partial: define the AID equation.
326 */
327struct cfg80211_he_bss_color {
328 u8 color;
329 bool enabled;
330 bool partial;
331};
332
333/**
334 * struct ieee80211_sta_ht_cap - STA's HT capabilities
335 *
336 * This structure describes most essential parameters needed
337 * to describe 802.11n HT capabilities for an STA.
338 *
339 * @ht_supported: is HT supported by the STA
340 * @cap: HT capabilities map as described in 802.11n spec
341 * @ampdu_factor: Maximum A-MPDU length factor
342 * @ampdu_density: Minimum A-MPDU spacing
343 * @mcs: Supported MCS rates
344 */
345struct ieee80211_sta_ht_cap {
346 u16 cap; /* use IEEE80211_HT_CAP_ */
347 bool ht_supported;
348 u8 ampdu_factor;
349 u8 ampdu_density;
350 struct ieee80211_mcs_info mcs;
351};
352
353/**
354 * struct ieee80211_sta_vht_cap - STA's VHT capabilities
355 *
356 * This structure describes most essential parameters needed
357 * to describe 802.11ac VHT capabilities for an STA.
358 *
359 * @vht_supported: is VHT supported by the STA
360 * @cap: VHT capabilities map as described in 802.11ac spec
361 * @vht_mcs: Supported VHT MCS rates
362 */
363struct ieee80211_sta_vht_cap {
364 bool vht_supported;
365 u32 cap; /* use IEEE80211_VHT_CAP_ */
366 struct ieee80211_vht_mcs_info vht_mcs;
367};
368
369#define IEEE80211_HE_PPE_THRES_MAX_LEN 25
370
371/**
372 * struct ieee80211_sta_he_cap - STA's HE capabilities
373 *
374 * This structure describes most essential parameters needed
375 * to describe 802.11ax HE capabilities for a STA.
376 *
377 * @has_he: true iff HE data is valid.
378 * @he_cap_elem: Fixed portion of the HE capabilities element.
379 * @he_mcs_nss_supp: The supported NSS/MCS combinations.
380 * @ppe_thres: Holds the PPE Thresholds data.
381 */
382struct ieee80211_sta_he_cap {
383 bool has_he;
384 struct ieee80211_he_cap_elem he_cap_elem;
385 struct ieee80211_he_mcs_nss_supp he_mcs_nss_supp;
386 u8 ppe_thres[IEEE80211_HE_PPE_THRES_MAX_LEN];
387};
388
389/**
390 * struct ieee80211_eht_mcs_nss_supp - EHT max supported NSS per MCS
391 *
392 * See P802.11be_D1.3 Table 9-401k - "Subfields of the Supported EHT-MCS
393 * and NSS Set field"
394 *
395 * @only_20mhz: MCS/NSS support for 20 MHz-only STA.
396 * @bw: MCS/NSS support for 80, 160 and 320 MHz
397 * @bw._80: MCS/NSS support for BW <= 80 MHz
398 * @bw._160: MCS/NSS support for BW = 160 MHz
399 * @bw._320: MCS/NSS support for BW = 320 MHz
400 */
401struct ieee80211_eht_mcs_nss_supp {
402 union {
403 struct ieee80211_eht_mcs_nss_supp_20mhz_only only_20mhz;
404 struct {
405 struct ieee80211_eht_mcs_nss_supp_bw _80;
406 struct ieee80211_eht_mcs_nss_supp_bw _160;
407 struct ieee80211_eht_mcs_nss_supp_bw _320;
408 } __packed bw;
409 } __packed;
410} __packed;
411
412#define IEEE80211_EHT_PPE_THRES_MAX_LEN 32
413
414/**
415 * struct ieee80211_sta_eht_cap - STA's EHT capabilities
416 *
417 * This structure describes most essential parameters needed
418 * to describe 802.11be EHT capabilities for a STA.
419 *
420 * @has_eht: true iff EHT data is valid.
421 * @eht_cap_elem: Fixed portion of the eht capabilities element.
422 * @eht_mcs_nss_supp: The supported NSS/MCS combinations.
423 * @eht_ppe_thres: Holds the PPE Thresholds data.
424 */
425struct ieee80211_sta_eht_cap {
426 bool has_eht;
427 struct ieee80211_eht_cap_elem_fixed eht_cap_elem;
428 struct ieee80211_eht_mcs_nss_supp eht_mcs_nss_supp;
429 u8 eht_ppe_thres[IEEE80211_EHT_PPE_THRES_MAX_LEN];
430};
431
432/* sparse defines __CHECKER__; see Documentation/dev-tools/sparse.rst */
433#ifdef __CHECKER__
434/*
435 * This is used to mark the sband->iftype_data pointer which is supposed
436 * to be an array with special access semantics (per iftype), but a lot
437 * of code got it wrong in the past, so with this marking sparse will be
438 * noisy when the pointer is used directly.
439 */
440# define __iftd __attribute__((noderef, address_space(__iftype_data)))
441#else
442# define __iftd
443#endif /* __CHECKER__ */
444
445/**
446 * struct ieee80211_sband_iftype_data - sband data per interface type
447 *
448 * This structure encapsulates sband data that is relevant for the
449 * interface types defined in @types_mask. Each type in the
450 * @types_mask must be unique across all instances of iftype_data.
451 *
452 * @types_mask: interface types mask
453 * @he_cap: holds the HE capabilities
454 * @he_6ghz_capa: HE 6 GHz capabilities, must be filled in for a
455 * 6 GHz band channel (and 0 may be valid value).
456 * @eht_cap: STA's EHT capabilities
457 * @vendor_elems: vendor element(s) to advertise
458 * @vendor_elems.data: vendor element(s) data
459 * @vendor_elems.len: vendor element(s) length
460 */
461struct ieee80211_sband_iftype_data {
462 u16 types_mask;
463 struct ieee80211_sta_he_cap he_cap;
464 struct ieee80211_he_6ghz_capa he_6ghz_capa;
465 struct ieee80211_sta_eht_cap eht_cap;
466 struct {
467 const u8 *data;
468 unsigned int len;
469 } vendor_elems;
470};
471
472/**
473 * enum ieee80211_edmg_bw_config - allowed channel bandwidth configurations
474 *
475 * @IEEE80211_EDMG_BW_CONFIG_4: 2.16GHz
476 * @IEEE80211_EDMG_BW_CONFIG_5: 2.16GHz and 4.32GHz
477 * @IEEE80211_EDMG_BW_CONFIG_6: 2.16GHz, 4.32GHz and 6.48GHz
478 * @IEEE80211_EDMG_BW_CONFIG_7: 2.16GHz, 4.32GHz, 6.48GHz and 8.64GHz
479 * @IEEE80211_EDMG_BW_CONFIG_8: 2.16GHz and 2.16GHz + 2.16GHz
480 * @IEEE80211_EDMG_BW_CONFIG_9: 2.16GHz, 4.32GHz and 2.16GHz + 2.16GHz
481 * @IEEE80211_EDMG_BW_CONFIG_10: 2.16GHz, 4.32GHz, 6.48GHz and 2.16GHz+2.16GHz
482 * @IEEE80211_EDMG_BW_CONFIG_11: 2.16GHz, 4.32GHz, 6.48GHz, 8.64GHz and
483 * 2.16GHz+2.16GHz
484 * @IEEE80211_EDMG_BW_CONFIG_12: 2.16GHz, 2.16GHz + 2.16GHz and
485 * 4.32GHz + 4.32GHz
486 * @IEEE80211_EDMG_BW_CONFIG_13: 2.16GHz, 4.32GHz, 2.16GHz + 2.16GHz and
487 * 4.32GHz + 4.32GHz
488 * @IEEE80211_EDMG_BW_CONFIG_14: 2.16GHz, 4.32GHz, 6.48GHz, 2.16GHz + 2.16GHz
489 * and 4.32GHz + 4.32GHz
490 * @IEEE80211_EDMG_BW_CONFIG_15: 2.16GHz, 4.32GHz, 6.48GHz, 8.64GHz,
491 * 2.16GHz + 2.16GHz and 4.32GHz + 4.32GHz
492 */
493enum ieee80211_edmg_bw_config {
494 IEEE80211_EDMG_BW_CONFIG_4 = 4,
495 IEEE80211_EDMG_BW_CONFIG_5 = 5,
496 IEEE80211_EDMG_BW_CONFIG_6 = 6,
497 IEEE80211_EDMG_BW_CONFIG_7 = 7,
498 IEEE80211_EDMG_BW_CONFIG_8 = 8,
499 IEEE80211_EDMG_BW_CONFIG_9 = 9,
500 IEEE80211_EDMG_BW_CONFIG_10 = 10,
501 IEEE80211_EDMG_BW_CONFIG_11 = 11,
502 IEEE80211_EDMG_BW_CONFIG_12 = 12,
503 IEEE80211_EDMG_BW_CONFIG_13 = 13,
504 IEEE80211_EDMG_BW_CONFIG_14 = 14,
505 IEEE80211_EDMG_BW_CONFIG_15 = 15,
506};
507
508/**
509 * struct ieee80211_edmg - EDMG configuration
510 *
511 * This structure describes most essential parameters needed
512 * to describe 802.11ay EDMG configuration
513 *
514 * @channels: bitmap that indicates the 2.16 GHz channel(s)
515 * that are allowed to be used for transmissions.
516 * Bit 0 indicates channel 1, bit 1 indicates channel 2, etc.
517 * Set to 0 indicate EDMG not supported.
518 * @bw_config: Channel BW Configuration subfield encodes
519 * the allowed channel bandwidth configurations
520 */
521struct ieee80211_edmg {
522 u8 channels;
523 enum ieee80211_edmg_bw_config bw_config;
524};
525
526/**
527 * struct ieee80211_sta_s1g_cap - STA's S1G capabilities
528 *
529 * This structure describes most essential parameters needed
530 * to describe 802.11ah S1G capabilities for a STA.
531 *
532 * @s1g: is STA an S1G STA
533 * @cap: S1G capabilities information
534 * @nss_mcs: Supported NSS MCS set
535 */
536struct ieee80211_sta_s1g_cap {
537 bool s1g;
538 u8 cap[10]; /* use S1G_CAPAB_ */
539 u8 nss_mcs[5];
540};
541
542/**
543 * struct ieee80211_supported_band - frequency band definition
544 *
545 * This structure describes a frequency band a wiphy
546 * is able to operate in.
547 *
548 * @channels: Array of channels the hardware can operate with
549 * in this band.
550 * @band: the band this structure represents
551 * @n_channels: Number of channels in @channels
552 * @bitrates: Array of bitrates the hardware can operate with
553 * in this band. Must be sorted to give a valid "supported
554 * rates" IE, i.e. CCK rates first, then OFDM.
555 * @n_bitrates: Number of bitrates in @bitrates
556 * @ht_cap: HT capabilities in this band
557 * @vht_cap: VHT capabilities in this band
558 * @s1g_cap: S1G capabilities in this band
559 * @edmg_cap: EDMG capabilities in this band
560 * @s1g_cap: S1G capabilities in this band (S1B band only, of course)
561 * @n_iftype_data: number of iftype data entries
562 * @iftype_data: interface type data entries. Note that the bits in
563 * @types_mask inside this structure cannot overlap (i.e. only
564 * one occurrence of each type is allowed across all instances of
565 * iftype_data).
566 */
567struct ieee80211_supported_band {
568 struct ieee80211_channel *channels;
569 struct ieee80211_rate *bitrates;
570 enum nl80211_band band;
571 int n_channels;
572 int n_bitrates;
573 struct ieee80211_sta_ht_cap ht_cap;
574 struct ieee80211_sta_vht_cap vht_cap;
575 struct ieee80211_sta_s1g_cap s1g_cap;
576 struct ieee80211_edmg edmg_cap;
577 u16 n_iftype_data;
578 const struct ieee80211_sband_iftype_data __iftd *iftype_data;
579};
580
581/**
582 * _ieee80211_set_sband_iftype_data - set sband iftype data array
583 * @sband: the sband to initialize
584 * @iftd: the iftype data array pointer
585 * @n_iftd: the length of the iftype data array
586 *
587 * Set the sband iftype data array; use this where the length cannot
588 * be derived from the ARRAY_SIZE() of the argument, but prefer
589 * ieee80211_set_sband_iftype_data() where it can be used.
590 */
591static inline void
592_ieee80211_set_sband_iftype_data(struct ieee80211_supported_band *sband,
593 const struct ieee80211_sband_iftype_data *iftd,
594 u16 n_iftd)
595{
596 sband->iftype_data = (const void __iftd __force *)iftd;
597 sband->n_iftype_data = n_iftd;
598}
599
600/**
601 * ieee80211_set_sband_iftype_data - set sband iftype data array
602 * @sband: the sband to initialize
603 * @iftd: the iftype data array
604 */
605#define ieee80211_set_sband_iftype_data(sband, iftd) \
606 _ieee80211_set_sband_iftype_data(sband, iftd, ARRAY_SIZE(iftd))
607
608/**
609 * for_each_sband_iftype_data - iterate sband iftype data entries
610 * @sband: the sband whose iftype_data array to iterate
611 * @i: iterator counter
612 * @iftd: iftype data pointer to set
613 */
614#define for_each_sband_iftype_data(sband, i, iftd) \
615 for (i = 0, iftd = (const void __force *)&(sband)->iftype_data[i]; \
616 i < (sband)->n_iftype_data; \
617 i++, iftd = (const void __force *)&(sband)->iftype_data[i])
618
619/**
620 * ieee80211_get_sband_iftype_data - return sband data for a given iftype
621 * @sband: the sband to search for the STA on
622 * @iftype: enum nl80211_iftype
623 *
624 * Return: pointer to struct ieee80211_sband_iftype_data, or NULL is none found
625 */
626static inline const struct ieee80211_sband_iftype_data *
627ieee80211_get_sband_iftype_data(const struct ieee80211_supported_band *sband,
628 u8 iftype)
629{
630 const struct ieee80211_sband_iftype_data *data;
631 int i;
632
633 if (WARN_ON(iftype >= NL80211_IFTYPE_MAX))
634 return NULL;
635
636 if (iftype == NL80211_IFTYPE_AP_VLAN)
637 iftype = NL80211_IFTYPE_AP;
638
639 for_each_sband_iftype_data(sband, i, data) {
640 if (data->types_mask & BIT(iftype))
641 return data;
642 }
643
644 return NULL;
645}
646
647/**
648 * ieee80211_get_he_iftype_cap - return HE capabilities for an sband's iftype
649 * @sband: the sband to search for the iftype on
650 * @iftype: enum nl80211_iftype
651 *
652 * Return: pointer to the struct ieee80211_sta_he_cap, or NULL is none found
653 */
654static inline const struct ieee80211_sta_he_cap *
655ieee80211_get_he_iftype_cap(const struct ieee80211_supported_band *sband,
656 u8 iftype)
657{
658 const struct ieee80211_sband_iftype_data *data =
659 ieee80211_get_sband_iftype_data(sband, iftype);
660
661 if (data && data->he_cap.has_he)
662 return &data->he_cap;
663
664 return NULL;
665}
666
667/**
668 * ieee80211_get_he_6ghz_capa - return HE 6 GHz capabilities
669 * @sband: the sband to search for the STA on
670 * @iftype: the iftype to search for
671 *
672 * Return: the 6GHz capabilities
673 */
674static inline __le16
675ieee80211_get_he_6ghz_capa(const struct ieee80211_supported_band *sband,
676 enum nl80211_iftype iftype)
677{
678 const struct ieee80211_sband_iftype_data *data =
679 ieee80211_get_sband_iftype_data(sband, iftype);
680
681 if (WARN_ON(!data || !data->he_cap.has_he))
682 return 0;
683
684 return data->he_6ghz_capa.capa;
685}
686
687/**
688 * ieee80211_get_eht_iftype_cap - return ETH capabilities for an sband's iftype
689 * @sband: the sband to search for the iftype on
690 * @iftype: enum nl80211_iftype
691 *
692 * Return: pointer to the struct ieee80211_sta_eht_cap, or NULL is none found
693 */
694static inline const struct ieee80211_sta_eht_cap *
695ieee80211_get_eht_iftype_cap(const struct ieee80211_supported_band *sband,
696 enum nl80211_iftype iftype)
697{
698 const struct ieee80211_sband_iftype_data *data =
699 ieee80211_get_sband_iftype_data(sband, iftype);
700
701 if (data && data->eht_cap.has_eht)
702 return &data->eht_cap;
703
704 return NULL;
705}
706
707/**
708 * wiphy_read_of_freq_limits - read frequency limits from device tree
709 *
710 * @wiphy: the wireless device to get extra limits for
711 *
712 * Some devices may have extra limitations specified in DT. This may be useful
713 * for chipsets that normally support more bands but are limited due to board
714 * design (e.g. by antennas or external power amplifier).
715 *
716 * This function reads info from DT and uses it to *modify* channels (disable
717 * unavailable ones). It's usually a *bad* idea to use it in drivers with
718 * shared channel data as DT limitations are device specific. You should make
719 * sure to call it only if channels in wiphy are copied and can be modified
720 * without affecting other devices.
721 *
722 * As this function access device node it has to be called after set_wiphy_dev.
723 * It also modifies channels so they have to be set first.
724 * If using this helper, call it before wiphy_register().
725 */
726#ifdef CONFIG_OF
727void wiphy_read_of_freq_limits(struct wiphy *wiphy);
728#else /* CONFIG_OF */
729static inline void wiphy_read_of_freq_limits(struct wiphy *wiphy)
730{
731}
732#endif /* !CONFIG_OF */
733
734
735/*
736 * Wireless hardware/device configuration structures and methods
737 */
738
739/**
740 * DOC: Actions and configuration
741 *
742 * Each wireless device and each virtual interface offer a set of configuration
743 * operations and other actions that are invoked by userspace. Each of these
744 * actions is described in the operations structure, and the parameters these
745 * operations use are described separately.
746 *
747 * Additionally, some operations are asynchronous and expect to get status
748 * information via some functions that drivers need to call.
749 *
750 * Scanning and BSS list handling with its associated functionality is described
751 * in a separate chapter.
752 */
753
754#define VHT_MUMIMO_GROUPS_DATA_LEN (WLAN_MEMBERSHIP_LEN +\
755 WLAN_USER_POSITION_LEN)
756
757/**
758 * struct vif_params - describes virtual interface parameters
759 * @flags: monitor interface flags, unchanged if 0, otherwise
760 * %MONITOR_FLAG_CHANGED will be set
761 * @use_4addr: use 4-address frames
762 * @macaddr: address to use for this virtual interface.
763 * If this parameter is set to zero address the driver may
764 * determine the address as needed.
765 * This feature is only fully supported by drivers that enable the
766 * %NL80211_FEATURE_MAC_ON_CREATE flag. Others may support creating
767 ** only p2p devices with specified MAC.
768 * @vht_mumimo_groups: MU-MIMO groupID, used for monitoring MU-MIMO packets
769 * belonging to that MU-MIMO groupID; %NULL if not changed
770 * @vht_mumimo_follow_addr: MU-MIMO follow address, used for monitoring
771 * MU-MIMO packets going to the specified station; %NULL if not changed
772 */
773struct vif_params {
774 u32 flags;
775 int use_4addr;
776 u8 macaddr[ETH_ALEN];
777 const u8 *vht_mumimo_groups;
778 const u8 *vht_mumimo_follow_addr;
779};
780
781/**
782 * struct key_params - key information
783 *
784 * Information about a key
785 *
786 * @key: key material
787 * @key_len: length of key material
788 * @cipher: cipher suite selector
789 * @seq: sequence counter (IV/PN) for TKIP and CCMP keys, only used
790 * with the get_key() callback, must be in little endian,
791 * length given by @seq_len.
792 * @seq_len: length of @seq.
793 * @vlan_id: vlan_id for VLAN group key (if nonzero)
794 * @mode: key install mode (RX_TX, NO_TX or SET_TX)
795 */
796struct key_params {
797 const u8 *key;
798 const u8 *seq;
799 int key_len;
800 int seq_len;
801 u16 vlan_id;
802 u32 cipher;
803 enum nl80211_key_mode mode;
804};
805
806/**
807 * struct cfg80211_chan_def - channel definition
808 * @chan: the (control) channel
809 * @width: channel width
810 * @center_freq1: center frequency of first segment
811 * @center_freq2: center frequency of second segment
812 * (only with 80+80 MHz)
813 * @edmg: define the EDMG channels configuration.
814 * If edmg is requested (i.e. the .channels member is non-zero),
815 * chan will define the primary channel and all other
816 * parameters are ignored.
817 * @freq1_offset: offset from @center_freq1, in KHz
818 * @punctured: mask of the punctured 20 MHz subchannels, with
819 * bits turned on being disabled (punctured); numbered
820 * from lower to higher frequency (like in the spec)
821 */
822struct cfg80211_chan_def {
823 struct ieee80211_channel *chan;
824 enum nl80211_chan_width width;
825 u32 center_freq1;
826 u32 center_freq2;
827 struct ieee80211_edmg edmg;
828 u16 freq1_offset;
829 u16 punctured;
830};
831
832/*
833 * cfg80211_bitrate_mask - masks for bitrate control
834 */
835struct cfg80211_bitrate_mask {
836 struct {
837 u32 legacy;
838 u8 ht_mcs[IEEE80211_HT_MCS_MASK_LEN];
839 u16 vht_mcs[NL80211_VHT_NSS_MAX];
840 u16 he_mcs[NL80211_HE_NSS_MAX];
841 enum nl80211_txrate_gi gi;
842 enum nl80211_he_gi he_gi;
843 enum nl80211_he_ltf he_ltf;
844 } control[NUM_NL80211_BANDS];
845};
846
847
848/**
849 * struct cfg80211_tid_cfg - TID specific configuration
850 * @config_override: Flag to notify driver to reset TID configuration
851 * of the peer.
852 * @tids: bitmap of TIDs to modify
853 * @mask: bitmap of attributes indicating which parameter changed,
854 * similar to &nl80211_tid_config_supp.
855 * @noack: noack configuration value for the TID
856 * @retry_long: retry count value
857 * @retry_short: retry count value
858 * @ampdu: Enable/Disable MPDU aggregation
859 * @rtscts: Enable/Disable RTS/CTS
860 * @amsdu: Enable/Disable MSDU aggregation
861 * @txrate_type: Tx bitrate mask type
862 * @txrate_mask: Tx bitrate to be applied for the TID
863 */
864struct cfg80211_tid_cfg {
865 bool config_override;
866 u8 tids;
867 u64 mask;
868 enum nl80211_tid_config noack;
869 u8 retry_long, retry_short;
870 enum nl80211_tid_config ampdu;
871 enum nl80211_tid_config rtscts;
872 enum nl80211_tid_config amsdu;
873 enum nl80211_tx_rate_setting txrate_type;
874 struct cfg80211_bitrate_mask txrate_mask;
875};
876
877/**
878 * struct cfg80211_tid_config - TID configuration
879 * @peer: Station's MAC address
880 * @n_tid_conf: Number of TID specific configurations to be applied
881 * @tid_conf: Configuration change info
882 */
883struct cfg80211_tid_config {
884 const u8 *peer;
885 u32 n_tid_conf;
886 struct cfg80211_tid_cfg tid_conf[] __counted_by(n_tid_conf);
887};
888
889/**
890 * struct cfg80211_fils_aad - FILS AAD data
891 * @macaddr: STA MAC address
892 * @kek: FILS KEK
893 * @kek_len: FILS KEK length
894 * @snonce: STA Nonce
895 * @anonce: AP Nonce
896 */
897struct cfg80211_fils_aad {
898 const u8 *macaddr;
899 const u8 *kek;
900 u8 kek_len;
901 const u8 *snonce;
902 const u8 *anonce;
903};
904
905/**
906 * struct cfg80211_set_hw_timestamp - enable/disable HW timestamping
907 * @macaddr: peer MAC address. NULL to enable/disable HW timestamping for all
908 * addresses.
909 * @enable: if set, enable HW timestamping for the specified MAC address.
910 * Otherwise disable HW timestamping for the specified MAC address.
911 */
912struct cfg80211_set_hw_timestamp {
913 const u8 *macaddr;
914 bool enable;
915};
916
917/**
918 * cfg80211_get_chandef_type - return old channel type from chandef
919 * @chandef: the channel definition
920 *
921 * Return: The old channel type (NOHT, HT20, HT40+/-) from a given
922 * chandef, which must have a bandwidth allowing this conversion.
923 */
924static inline enum nl80211_channel_type
925cfg80211_get_chandef_type(const struct cfg80211_chan_def *chandef)
926{
927 switch (chandef->width) {
928 case NL80211_CHAN_WIDTH_20_NOHT:
929 return NL80211_CHAN_NO_HT;
930 case NL80211_CHAN_WIDTH_20:
931 return NL80211_CHAN_HT20;
932 case NL80211_CHAN_WIDTH_40:
933 if (chandef->center_freq1 > chandef->chan->center_freq)
934 return NL80211_CHAN_HT40PLUS;
935 return NL80211_CHAN_HT40MINUS;
936 default:
937 WARN_ON(1);
938 return NL80211_CHAN_NO_HT;
939 }
940}
941
942/**
943 * cfg80211_chandef_create - create channel definition using channel type
944 * @chandef: the channel definition struct to fill
945 * @channel: the control channel
946 * @chantype: the channel type
947 *
948 * Given a channel type, create a channel definition.
949 */
950void cfg80211_chandef_create(struct cfg80211_chan_def *chandef,
951 struct ieee80211_channel *channel,
952 enum nl80211_channel_type chantype);
953
954/**
955 * cfg80211_chandef_identical - check if two channel definitions are identical
956 * @chandef1: first channel definition
957 * @chandef2: second channel definition
958 *
959 * Return: %true if the channels defined by the channel definitions are
960 * identical, %false otherwise.
961 */
962static inline bool
963cfg80211_chandef_identical(const struct cfg80211_chan_def *chandef1,
964 const struct cfg80211_chan_def *chandef2)
965{
966 return (chandef1->chan == chandef2->chan &&
967 chandef1->width == chandef2->width &&
968 chandef1->center_freq1 == chandef2->center_freq1 &&
969 chandef1->freq1_offset == chandef2->freq1_offset &&
970 chandef1->center_freq2 == chandef2->center_freq2 &&
971 chandef1->punctured == chandef2->punctured);
972}
973
974/**
975 * cfg80211_chandef_is_edmg - check if chandef represents an EDMG channel
976 *
977 * @chandef: the channel definition
978 *
979 * Return: %true if EDMG defined, %false otherwise.
980 */
981static inline bool
982cfg80211_chandef_is_edmg(const struct cfg80211_chan_def *chandef)
983{
984 return chandef->edmg.channels || chandef->edmg.bw_config;
985}
986
987/**
988 * cfg80211_chandef_compatible - check if two channel definitions are compatible
989 * @chandef1: first channel definition
990 * @chandef2: second channel definition
991 *
992 * Return: %NULL if the given channel definitions are incompatible,
993 * chandef1 or chandef2 otherwise.
994 */
995const struct cfg80211_chan_def *
996cfg80211_chandef_compatible(const struct cfg80211_chan_def *chandef1,
997 const struct cfg80211_chan_def *chandef2);
998
999/**
1000 * nl80211_chan_width_to_mhz - get the channel width in MHz
1001 * @chan_width: the channel width from &enum nl80211_chan_width
1002 *
1003 * Return: channel width in MHz if the chan_width from &enum nl80211_chan_width
1004 * is valid. -1 otherwise.
1005 */
1006int nl80211_chan_width_to_mhz(enum nl80211_chan_width chan_width);
1007
1008/**
1009 * cfg80211_chandef_valid - check if a channel definition is valid
1010 * @chandef: the channel definition to check
1011 * Return: %true if the channel definition is valid. %false otherwise.
1012 */
1013bool cfg80211_chandef_valid(const struct cfg80211_chan_def *chandef);
1014
1015/**
1016 * cfg80211_chandef_usable - check if secondary channels can be used
1017 * @wiphy: the wiphy to validate against
1018 * @chandef: the channel definition to check
1019 * @prohibited_flags: the regulatory channel flags that must not be set
1020 * Return: %true if secondary channels are usable. %false otherwise.
1021 */
1022bool cfg80211_chandef_usable(struct wiphy *wiphy,
1023 const struct cfg80211_chan_def *chandef,
1024 u32 prohibited_flags);
1025
1026/**
1027 * cfg80211_chandef_dfs_required - checks if radar detection is required
1028 * @wiphy: the wiphy to validate against
1029 * @chandef: the channel definition to check
1030 * @iftype: the interface type as specified in &enum nl80211_iftype
1031 * Returns:
1032 * 1 if radar detection is required, 0 if it is not, < 0 on error
1033 */
1034int cfg80211_chandef_dfs_required(struct wiphy *wiphy,
1035 const struct cfg80211_chan_def *chandef,
1036 enum nl80211_iftype iftype);
1037
1038/**
1039 * cfg80211_chandef_dfs_usable - checks if chandef is DFS usable and we
1040 * can/need start CAC on such channel
1041 * @wiphy: the wiphy to validate against
1042 * @chandef: the channel definition to check
1043 *
1044 * Return: true if all channels available and at least
1045 * one channel requires CAC (NL80211_DFS_USABLE)
1046 */
1047bool cfg80211_chandef_dfs_usable(struct wiphy *wiphy,
1048 const struct cfg80211_chan_def *chandef);
1049
1050/**
1051 * cfg80211_chandef_dfs_cac_time - get the DFS CAC time (in ms) for given
1052 * channel definition
1053 * @wiphy: the wiphy to validate against
1054 * @chandef: the channel definition to check
1055 *
1056 * Returns: DFS CAC time (in ms) which applies for this channel definition
1057 */
1058unsigned int
1059cfg80211_chandef_dfs_cac_time(struct wiphy *wiphy,
1060 const struct cfg80211_chan_def *chandef);
1061
1062/**
1063 * cfg80211_chandef_primary - calculate primary 40/80/160 MHz freq
1064 * @chandef: chandef to calculate for
1065 * @primary_chan_width: primary channel width to calculate center for
1066 * @punctured: punctured sub-channel bitmap, will be recalculated
1067 * according to the new bandwidth, can be %NULL
1068 *
1069 * Returns: the primary 40/80/160 MHz channel center frequency, or -1
1070 * for errors, updating the punctured bitmap
1071 */
1072int cfg80211_chandef_primary(const struct cfg80211_chan_def *chandef,
1073 enum nl80211_chan_width primary_chan_width,
1074 u16 *punctured);
1075
1076/**
1077 * nl80211_send_chandef - sends the channel definition.
1078 * @msg: the msg to send channel definition
1079 * @chandef: the channel definition to check
1080 *
1081 * Returns: 0 if sent the channel definition to msg, < 0 on error
1082 **/
1083int nl80211_send_chandef(struct sk_buff *msg, const struct cfg80211_chan_def *chandef);
1084
1085/**
1086 * ieee80211_chanwidth_rate_flags - return rate flags for channel width
1087 * @width: the channel width of the channel
1088 *
1089 * In some channel types, not all rates may be used - for example CCK
1090 * rates may not be used in 5/10 MHz channels.
1091 *
1092 * Returns: rate flags which apply for this channel width
1093 */
1094static inline enum ieee80211_rate_flags
1095ieee80211_chanwidth_rate_flags(enum nl80211_chan_width width)
1096{
1097 switch (width) {
1098 case NL80211_CHAN_WIDTH_5:
1099 return IEEE80211_RATE_SUPPORTS_5MHZ;
1100 case NL80211_CHAN_WIDTH_10:
1101 return IEEE80211_RATE_SUPPORTS_10MHZ;
1102 default:
1103 break;
1104 }
1105 return 0;
1106}
1107
1108/**
1109 * ieee80211_chandef_rate_flags - returns rate flags for a channel
1110 * @chandef: channel definition for the channel
1111 *
1112 * See ieee80211_chanwidth_rate_flags().
1113 *
1114 * Returns: rate flags which apply for this channel
1115 */
1116static inline enum ieee80211_rate_flags
1117ieee80211_chandef_rate_flags(struct cfg80211_chan_def *chandef)
1118{
1119 return ieee80211_chanwidth_rate_flags(chandef->width);
1120}
1121
1122/**
1123 * ieee80211_chandef_max_power - maximum transmission power for the chandef
1124 *
1125 * In some regulations, the transmit power may depend on the configured channel
1126 * bandwidth which may be defined as dBm/MHz. This function returns the actual
1127 * max_power for non-standard (20 MHz) channels.
1128 *
1129 * @chandef: channel definition for the channel
1130 *
1131 * Returns: maximum allowed transmission power in dBm for the chandef
1132 */
1133static inline int
1134ieee80211_chandef_max_power(struct cfg80211_chan_def *chandef)
1135{
1136 switch (chandef->width) {
1137 case NL80211_CHAN_WIDTH_5:
1138 return min(chandef->chan->max_reg_power - 6,
1139 chandef->chan->max_power);
1140 case NL80211_CHAN_WIDTH_10:
1141 return min(chandef->chan->max_reg_power - 3,
1142 chandef->chan->max_power);
1143 default:
1144 break;
1145 }
1146 return chandef->chan->max_power;
1147}
1148
1149/**
1150 * cfg80211_any_usable_channels - check for usable channels
1151 * @wiphy: the wiphy to check for
1152 * @band_mask: which bands to check on
1153 * @prohibited_flags: which channels to not consider usable,
1154 * %IEEE80211_CHAN_DISABLED is always taken into account
1155 *
1156 * Return: %true if usable channels found, %false otherwise
1157 */
1158bool cfg80211_any_usable_channels(struct wiphy *wiphy,
1159 unsigned long band_mask,
1160 u32 prohibited_flags);
1161
1162/**
1163 * enum survey_info_flags - survey information flags
1164 *
1165 * @SURVEY_INFO_NOISE_DBM: noise (in dBm) was filled in
1166 * @SURVEY_INFO_IN_USE: channel is currently being used
1167 * @SURVEY_INFO_TIME: active time (in ms) was filled in
1168 * @SURVEY_INFO_TIME_BUSY: busy time was filled in
1169 * @SURVEY_INFO_TIME_EXT_BUSY: extension channel busy time was filled in
1170 * @SURVEY_INFO_TIME_RX: receive time was filled in
1171 * @SURVEY_INFO_TIME_TX: transmit time was filled in
1172 * @SURVEY_INFO_TIME_SCAN: scan time was filled in
1173 * @SURVEY_INFO_TIME_BSS_RX: local BSS receive time was filled in
1174 *
1175 * Used by the driver to indicate which info in &struct survey_info
1176 * it has filled in during the get_survey().
1177 */
1178enum survey_info_flags {
1179 SURVEY_INFO_NOISE_DBM = BIT(0),
1180 SURVEY_INFO_IN_USE = BIT(1),
1181 SURVEY_INFO_TIME = BIT(2),
1182 SURVEY_INFO_TIME_BUSY = BIT(3),
1183 SURVEY_INFO_TIME_EXT_BUSY = BIT(4),
1184 SURVEY_INFO_TIME_RX = BIT(5),
1185 SURVEY_INFO_TIME_TX = BIT(6),
1186 SURVEY_INFO_TIME_SCAN = BIT(7),
1187 SURVEY_INFO_TIME_BSS_RX = BIT(8),
1188};
1189
1190/**
1191 * struct survey_info - channel survey response
1192 *
1193 * @channel: the channel this survey record reports, may be %NULL for a single
1194 * record to report global statistics
1195 * @filled: bitflag of flags from &enum survey_info_flags
1196 * @noise: channel noise in dBm. This and all following fields are
1197 * optional
1198 * @time: amount of time in ms the radio was turn on (on the channel)
1199 * @time_busy: amount of time the primary channel was sensed busy
1200 * @time_ext_busy: amount of time the extension channel was sensed busy
1201 * @time_rx: amount of time the radio spent receiving data
1202 * @time_tx: amount of time the radio spent transmitting data
1203 * @time_scan: amount of time the radio spent for scanning
1204 * @time_bss_rx: amount of time the radio spent receiving data on a local BSS
1205 *
1206 * Used by dump_survey() to report back per-channel survey information.
1207 *
1208 * This structure can later be expanded with things like
1209 * channel duty cycle etc.
1210 */
1211struct survey_info {
1212 struct ieee80211_channel *channel;
1213 u64 time;
1214 u64 time_busy;
1215 u64 time_ext_busy;
1216 u64 time_rx;
1217 u64 time_tx;
1218 u64 time_scan;
1219 u64 time_bss_rx;
1220 u32 filled;
1221 s8 noise;
1222};
1223
1224#define CFG80211_MAX_NUM_AKM_SUITES 10
1225
1226/**
1227 * struct cfg80211_crypto_settings - Crypto settings
1228 * @wpa_versions: indicates which, if any, WPA versions are enabled
1229 * (from enum nl80211_wpa_versions)
1230 * @cipher_group: group key cipher suite (or 0 if unset)
1231 * @n_ciphers_pairwise: number of AP supported unicast ciphers
1232 * @ciphers_pairwise: unicast key cipher suites
1233 * @n_akm_suites: number of AKM suites
1234 * @akm_suites: AKM suites
1235 * @control_port: Whether user space controls IEEE 802.1X port, i.e.,
1236 * sets/clears %NL80211_STA_FLAG_AUTHORIZED. If true, the driver is
1237 * required to assume that the port is unauthorized until authorized by
1238 * user space. Otherwise, port is marked authorized by default.
1239 * @control_port_ethertype: the control port protocol that should be
1240 * allowed through even on unauthorized ports
1241 * @control_port_no_encrypt: TRUE to prevent encryption of control port
1242 * protocol frames.
1243 * @control_port_over_nl80211: TRUE if userspace expects to exchange control
1244 * port frames over NL80211 instead of the network interface.
1245 * @control_port_no_preauth: disables pre-auth rx over the nl80211 control
1246 * port for mac80211
1247 * @psk: PSK (for devices supporting 4-way-handshake offload)
1248 * @sae_pwd: password for SAE authentication (for devices supporting SAE
1249 * offload)
1250 * @sae_pwd_len: length of SAE password (for devices supporting SAE offload)
1251 * @sae_pwe: The mechanisms allowed for SAE PWE derivation:
1252 *
1253 * NL80211_SAE_PWE_UNSPECIFIED
1254 * Not-specified, used to indicate userspace did not specify any
1255 * preference. The driver should follow its internal policy in
1256 * such a scenario.
1257 *
1258 * NL80211_SAE_PWE_HUNT_AND_PECK
1259 * Allow hunting-and-pecking loop only
1260 *
1261 * NL80211_SAE_PWE_HASH_TO_ELEMENT
1262 * Allow hash-to-element only
1263 *
1264 * NL80211_SAE_PWE_BOTH
1265 * Allow either hunting-and-pecking loop or hash-to-element
1266 */
1267struct cfg80211_crypto_settings {
1268 u32 wpa_versions;
1269 u32 cipher_group;
1270 int n_ciphers_pairwise;
1271 u32 ciphers_pairwise[NL80211_MAX_NR_CIPHER_SUITES];
1272 int n_akm_suites;
1273 u32 akm_suites[CFG80211_MAX_NUM_AKM_SUITES];
1274 bool control_port;
1275 __be16 control_port_ethertype;
1276 bool control_port_no_encrypt;
1277 bool control_port_over_nl80211;
1278 bool control_port_no_preauth;
1279 const u8 *psk;
1280 const u8 *sae_pwd;
1281 u8 sae_pwd_len;
1282 enum nl80211_sae_pwe_mechanism sae_pwe;
1283};
1284
1285/**
1286 * struct cfg80211_mbssid_config - AP settings for multi bssid
1287 *
1288 * @tx_wdev: pointer to the transmitted interface in the MBSSID set
1289 * @index: index of this AP in the multi bssid group.
1290 * @ema: set to true if the beacons should be sent out in EMA mode.
1291 */
1292struct cfg80211_mbssid_config {
1293 struct wireless_dev *tx_wdev;
1294 u8 index;
1295 bool ema;
1296};
1297
1298/**
1299 * struct cfg80211_mbssid_elems - Multiple BSSID elements
1300 *
1301 * @cnt: Number of elements in array %elems.
1302 *
1303 * @elem: Array of multiple BSSID element(s) to be added into Beacon frames.
1304 * @elem.data: Data for multiple BSSID elements.
1305 * @elem.len: Length of data.
1306 */
1307struct cfg80211_mbssid_elems {
1308 u8 cnt;
1309 struct {
1310 const u8 *data;
1311 size_t len;
1312 } elem[] __counted_by(cnt);
1313};
1314
1315/**
1316 * struct cfg80211_rnr_elems - Reduced neighbor report (RNR) elements
1317 *
1318 * @cnt: Number of elements in array %elems.
1319 *
1320 * @elem: Array of RNR element(s) to be added into Beacon frames.
1321 * @elem.data: Data for RNR elements.
1322 * @elem.len: Length of data.
1323 */
1324struct cfg80211_rnr_elems {
1325 u8 cnt;
1326 struct {
1327 const u8 *data;
1328 size_t len;
1329 } elem[] __counted_by(cnt);
1330};
1331
1332/**
1333 * struct cfg80211_beacon_data - beacon data
1334 * @link_id: the link ID for the AP MLD link sending this beacon
1335 * @head: head portion of beacon (before TIM IE)
1336 * or %NULL if not changed
1337 * @tail: tail portion of beacon (after TIM IE)
1338 * or %NULL if not changed
1339 * @head_len: length of @head
1340 * @tail_len: length of @tail
1341 * @beacon_ies: extra information element(s) to add into Beacon frames or %NULL
1342 * @beacon_ies_len: length of beacon_ies in octets
1343 * @proberesp_ies: extra information element(s) to add into Probe Response
1344 * frames or %NULL
1345 * @proberesp_ies_len: length of proberesp_ies in octets
1346 * @assocresp_ies: extra information element(s) to add into (Re)Association
1347 * Response frames or %NULL
1348 * @assocresp_ies_len: length of assocresp_ies in octets
1349 * @probe_resp_len: length of probe response template (@probe_resp)
1350 * @probe_resp: probe response template (AP mode only)
1351 * @mbssid_ies: multiple BSSID elements
1352 * @rnr_ies: reduced neighbor report elements
1353 * @ftm_responder: enable FTM responder functionality; -1 for no change
1354 * (which also implies no change in LCI/civic location data)
1355 * @lci: Measurement Report element content, starting with Measurement Token
1356 * (measurement type 8)
1357 * @civicloc: Measurement Report element content, starting with Measurement
1358 * Token (measurement type 11)
1359 * @lci_len: LCI data length
1360 * @civicloc_len: Civic location data length
1361 * @he_bss_color: BSS Color settings
1362 * @he_bss_color_valid: indicates whether bss color
1363 * attribute is present in beacon data or not.
1364 */
1365struct cfg80211_beacon_data {
1366 unsigned int link_id;
1367
1368 const u8 *head, *tail;
1369 const u8 *beacon_ies;
1370 const u8 *proberesp_ies;
1371 const u8 *assocresp_ies;
1372 const u8 *probe_resp;
1373 const u8 *lci;
1374 const u8 *civicloc;
1375 struct cfg80211_mbssid_elems *mbssid_ies;
1376 struct cfg80211_rnr_elems *rnr_ies;
1377 s8 ftm_responder;
1378
1379 size_t head_len, tail_len;
1380 size_t beacon_ies_len;
1381 size_t proberesp_ies_len;
1382 size_t assocresp_ies_len;
1383 size_t probe_resp_len;
1384 size_t lci_len;
1385 size_t civicloc_len;
1386 struct cfg80211_he_bss_color he_bss_color;
1387 bool he_bss_color_valid;
1388};
1389
1390struct mac_address {
1391 u8 addr[ETH_ALEN];
1392};
1393
1394/**
1395 * struct cfg80211_acl_data - Access control list data
1396 *
1397 * @acl_policy: ACL policy to be applied on the station's
1398 * entry specified by mac_addr
1399 * @n_acl_entries: Number of MAC address entries passed
1400 * @mac_addrs: List of MAC addresses of stations to be used for ACL
1401 */
1402struct cfg80211_acl_data {
1403 enum nl80211_acl_policy acl_policy;
1404 int n_acl_entries;
1405
1406 /* Keep it last */
1407 struct mac_address mac_addrs[] __counted_by(n_acl_entries);
1408};
1409
1410/**
1411 * struct cfg80211_fils_discovery - FILS discovery parameters from
1412 * IEEE Std 802.11ai-2016, Annex C.3 MIB detail.
1413 *
1414 * @update: Set to true if the feature configuration should be updated.
1415 * @min_interval: Minimum packet interval in TUs (0 - 10000)
1416 * @max_interval: Maximum packet interval in TUs (0 - 10000)
1417 * @tmpl_len: Template length
1418 * @tmpl: Template data for FILS discovery frame including the action
1419 * frame headers.
1420 */
1421struct cfg80211_fils_discovery {
1422 bool update;
1423 u32 min_interval;
1424 u32 max_interval;
1425 size_t tmpl_len;
1426 const u8 *tmpl;
1427};
1428
1429/**
1430 * struct cfg80211_unsol_bcast_probe_resp - Unsolicited broadcast probe
1431 * response parameters in 6GHz.
1432 *
1433 * @update: Set to true if the feature configuration should be updated.
1434 * @interval: Packet interval in TUs. Maximum allowed is 20 TU, as mentioned
1435 * in IEEE P802.11ax/D6.0 26.17.2.3.2 - AP behavior for fast passive
1436 * scanning
1437 * @tmpl_len: Template length
1438 * @tmpl: Template data for probe response
1439 */
1440struct cfg80211_unsol_bcast_probe_resp {
1441 bool update;
1442 u32 interval;
1443 size_t tmpl_len;
1444 const u8 *tmpl;
1445};
1446
1447/**
1448 * struct cfg80211_ap_settings - AP configuration
1449 *
1450 * Used to configure an AP interface.
1451 *
1452 * @chandef: defines the channel to use
1453 * @beacon: beacon data
1454 * @beacon_interval: beacon interval
1455 * @dtim_period: DTIM period
1456 * @ssid: SSID to be used in the BSS (note: may be %NULL if not provided from
1457 * user space)
1458 * @ssid_len: length of @ssid
1459 * @hidden_ssid: whether to hide the SSID in Beacon/Probe Response frames
1460 * @crypto: crypto settings
1461 * @privacy: the BSS uses privacy
1462 * @auth_type: Authentication type (algorithm)
1463 * @inactivity_timeout: time in seconds to determine station's inactivity.
1464 * @p2p_ctwindow: P2P CT Window
1465 * @p2p_opp_ps: P2P opportunistic PS
1466 * @acl: ACL configuration used by the drivers which has support for
1467 * MAC address based access control
1468 * @pbss: If set, start as a PCP instead of AP. Relevant for DMG
1469 * networks.
1470 * @beacon_rate: bitrate to be used for beacons
1471 * @ht_cap: HT capabilities (or %NULL if HT isn't enabled)
1472 * @vht_cap: VHT capabilities (or %NULL if VHT isn't enabled)
1473 * @he_cap: HE capabilities (or %NULL if HE isn't enabled)
1474 * @eht_cap: EHT capabilities (or %NULL if EHT isn't enabled)
1475 * @eht_oper: EHT operation IE (or %NULL if EHT isn't enabled)
1476 * @ht_required: stations must support HT
1477 * @vht_required: stations must support VHT
1478 * @twt_responder: Enable Target Wait Time
1479 * @he_required: stations must support HE
1480 * @sae_h2e_required: stations must support direct H2E technique in SAE
1481 * @flags: flags, as defined in &enum nl80211_ap_settings_flags
1482 * @he_obss_pd: OBSS Packet Detection settings
1483 * @he_oper: HE operation IE (or %NULL if HE isn't enabled)
1484 * @fils_discovery: FILS discovery transmission parameters
1485 * @unsol_bcast_probe_resp: Unsolicited broadcast probe response parameters
1486 * @mbssid_config: AP settings for multiple bssid
1487 */
1488struct cfg80211_ap_settings {
1489 struct cfg80211_chan_def chandef;
1490
1491 struct cfg80211_beacon_data beacon;
1492
1493 int beacon_interval, dtim_period;
1494 const u8 *ssid;
1495 size_t ssid_len;
1496 enum nl80211_hidden_ssid hidden_ssid;
1497 struct cfg80211_crypto_settings crypto;
1498 bool privacy;
1499 enum nl80211_auth_type auth_type;
1500 int inactivity_timeout;
1501 u8 p2p_ctwindow;
1502 bool p2p_opp_ps;
1503 const struct cfg80211_acl_data *acl;
1504 bool pbss;
1505 struct cfg80211_bitrate_mask beacon_rate;
1506
1507 const struct ieee80211_ht_cap *ht_cap;
1508 const struct ieee80211_vht_cap *vht_cap;
1509 const struct ieee80211_he_cap_elem *he_cap;
1510 const struct ieee80211_he_operation *he_oper;
1511 const struct ieee80211_eht_cap_elem *eht_cap;
1512 const struct ieee80211_eht_operation *eht_oper;
1513 bool ht_required, vht_required, he_required, sae_h2e_required;
1514 bool twt_responder;
1515 u32 flags;
1516 struct ieee80211_he_obss_pd he_obss_pd;
1517 struct cfg80211_fils_discovery fils_discovery;
1518 struct cfg80211_unsol_bcast_probe_resp unsol_bcast_probe_resp;
1519 struct cfg80211_mbssid_config mbssid_config;
1520};
1521
1522
1523/**
1524 * struct cfg80211_ap_update - AP configuration update
1525 *
1526 * Subset of &struct cfg80211_ap_settings, for updating a running AP.
1527 *
1528 * @beacon: beacon data
1529 * @fils_discovery: FILS discovery transmission parameters
1530 * @unsol_bcast_probe_resp: Unsolicited broadcast probe response parameters
1531 */
1532struct cfg80211_ap_update {
1533 struct cfg80211_beacon_data beacon;
1534 struct cfg80211_fils_discovery fils_discovery;
1535 struct cfg80211_unsol_bcast_probe_resp unsol_bcast_probe_resp;
1536};
1537
1538/**
1539 * struct cfg80211_csa_settings - channel switch settings
1540 *
1541 * Used for channel switch
1542 *
1543 * @chandef: defines the channel to use after the switch
1544 * @beacon_csa: beacon data while performing the switch
1545 * @counter_offsets_beacon: offsets of the counters within the beacon (tail)
1546 * @counter_offsets_presp: offsets of the counters within the probe response
1547 * @n_counter_offsets_beacon: number of csa counters the beacon (tail)
1548 * @n_counter_offsets_presp: number of csa counters in the probe response
1549 * @beacon_after: beacon data to be used on the new channel
1550 * @radar_required: whether radar detection is required on the new channel
1551 * @block_tx: whether transmissions should be blocked while changing
1552 * @count: number of beacons until switch
1553 * @link_id: defines the link on which channel switch is expected during
1554 * MLO. 0 in case of non-MLO.
1555 */
1556struct cfg80211_csa_settings {
1557 struct cfg80211_chan_def chandef;
1558 struct cfg80211_beacon_data beacon_csa;
1559 const u16 *counter_offsets_beacon;
1560 const u16 *counter_offsets_presp;
1561 unsigned int n_counter_offsets_beacon;
1562 unsigned int n_counter_offsets_presp;
1563 struct cfg80211_beacon_data beacon_after;
1564 bool radar_required;
1565 bool block_tx;
1566 u8 count;
1567 u8 link_id;
1568};
1569
1570/**
1571 * struct cfg80211_color_change_settings - color change settings
1572 *
1573 * Used for bss color change
1574 *
1575 * @beacon_color_change: beacon data while performing the color countdown
1576 * @counter_offset_beacon: offsets of the counters within the beacon (tail)
1577 * @counter_offset_presp: offsets of the counters within the probe response
1578 * @beacon_next: beacon data to be used after the color change
1579 * @count: number of beacons until the color change
1580 * @color: the color used after the change
1581 * @link_id: defines the link on which color change is expected during MLO.
1582 * 0 in case of non-MLO.
1583 */
1584struct cfg80211_color_change_settings {
1585 struct cfg80211_beacon_data beacon_color_change;
1586 u16 counter_offset_beacon;
1587 u16 counter_offset_presp;
1588 struct cfg80211_beacon_data beacon_next;
1589 u8 count;
1590 u8 color;
1591 u8 link_id;
1592};
1593
1594/**
1595 * struct iface_combination_params - input parameters for interface combinations
1596 *
1597 * Used to pass interface combination parameters
1598 *
1599 * @radio_idx: wiphy radio index or -1 for global
1600 * @num_different_channels: the number of different channels we want
1601 * to use for verification
1602 * @radar_detect: a bitmap where each bit corresponds to a channel
1603 * width where radar detection is needed, as in the definition of
1604 * &struct ieee80211_iface_combination.@radar_detect_widths
1605 * @iftype_num: array with the number of interfaces of each interface
1606 * type. The index is the interface type as specified in &enum
1607 * nl80211_iftype.
1608 * @new_beacon_int: set this to the beacon interval of a new interface
1609 * that's not operating yet, if such is to be checked as part of
1610 * the verification
1611 */
1612struct iface_combination_params {
1613 int radio_idx;
1614 int num_different_channels;
1615 u8 radar_detect;
1616 int iftype_num[NUM_NL80211_IFTYPES];
1617 u32 new_beacon_int;
1618};
1619
1620/**
1621 * enum station_parameters_apply_mask - station parameter values to apply
1622 * @STATION_PARAM_APPLY_UAPSD: apply new uAPSD parameters (uapsd_queues, max_sp)
1623 * @STATION_PARAM_APPLY_CAPABILITY: apply new capability
1624 * @STATION_PARAM_APPLY_PLINK_STATE: apply new plink state
1625 *
1626 * Not all station parameters have in-band "no change" signalling,
1627 * for those that don't these flags will are used.
1628 */
1629enum station_parameters_apply_mask {
1630 STATION_PARAM_APPLY_UAPSD = BIT(0),
1631 STATION_PARAM_APPLY_CAPABILITY = BIT(1),
1632 STATION_PARAM_APPLY_PLINK_STATE = BIT(2),
1633};
1634
1635/**
1636 * struct sta_txpwr - station txpower configuration
1637 *
1638 * Used to configure txpower for station.
1639 *
1640 * @power: tx power (in dBm) to be used for sending data traffic. If tx power
1641 * is not provided, the default per-interface tx power setting will be
1642 * overriding. Driver should be picking up the lowest tx power, either tx
1643 * power per-interface or per-station.
1644 * @type: In particular if TPC %type is NL80211_TX_POWER_LIMITED then tx power
1645 * will be less than or equal to specified from userspace, whereas if TPC
1646 * %type is NL80211_TX_POWER_AUTOMATIC then it indicates default tx power.
1647 * NL80211_TX_POWER_FIXED is not a valid configuration option for
1648 * per peer TPC.
1649 */
1650struct sta_txpwr {
1651 s16 power;
1652 enum nl80211_tx_power_setting type;
1653};
1654
1655/**
1656 * struct link_station_parameters - link station parameters
1657 *
1658 * Used to change and create a new link station.
1659 *
1660 * @mld_mac: MAC address of the station
1661 * @link_id: the link id (-1 for non-MLD station)
1662 * @link_mac: MAC address of the link
1663 * @supported_rates: supported rates in IEEE 802.11 format
1664 * (or NULL for no change)
1665 * @supported_rates_len: number of supported rates
1666 * @ht_capa: HT capabilities of station
1667 * @vht_capa: VHT capabilities of station
1668 * @opmode_notif: operating mode field from Operating Mode Notification
1669 * @opmode_notif_used: information if operating mode field is used
1670 * @he_capa: HE capabilities of station
1671 * @he_capa_len: the length of the HE capabilities
1672 * @txpwr: transmit power for an associated station
1673 * @txpwr_set: txpwr field is set
1674 * @he_6ghz_capa: HE 6 GHz Band capabilities of station
1675 * @eht_capa: EHT capabilities of station
1676 * @eht_capa_len: the length of the EHT capabilities
1677 */
1678struct link_station_parameters {
1679 const u8 *mld_mac;
1680 int link_id;
1681 const u8 *link_mac;
1682 const u8 *supported_rates;
1683 u8 supported_rates_len;
1684 const struct ieee80211_ht_cap *ht_capa;
1685 const struct ieee80211_vht_cap *vht_capa;
1686 u8 opmode_notif;
1687 bool opmode_notif_used;
1688 const struct ieee80211_he_cap_elem *he_capa;
1689 u8 he_capa_len;
1690 struct sta_txpwr txpwr;
1691 bool txpwr_set;
1692 const struct ieee80211_he_6ghz_capa *he_6ghz_capa;
1693 const struct ieee80211_eht_cap_elem *eht_capa;
1694 u8 eht_capa_len;
1695};
1696
1697/**
1698 * struct link_station_del_parameters - link station deletion parameters
1699 *
1700 * Used to delete a link station entry (or all stations).
1701 *
1702 * @mld_mac: MAC address of the station
1703 * @link_id: the link id
1704 */
1705struct link_station_del_parameters {
1706 const u8 *mld_mac;
1707 u32 link_id;
1708};
1709
1710/**
1711 * struct cfg80211_ttlm_params: TID to link mapping parameters
1712 *
1713 * Used for setting a TID to link mapping.
1714 *
1715 * @dlink: Downlink TID to link mapping, as defined in section 9.4.2.314
1716 * (TID-To-Link Mapping element) in Draft P802.11be_D4.0.
1717 * @ulink: Uplink TID to link mapping, as defined in section 9.4.2.314
1718 * (TID-To-Link Mapping element) in Draft P802.11be_D4.0.
1719 */
1720struct cfg80211_ttlm_params {
1721 u16 dlink[8];
1722 u16 ulink[8];
1723};
1724
1725/**
1726 * struct station_parameters - station parameters
1727 *
1728 * Used to change and create a new station.
1729 *
1730 * @vlan: vlan interface station should belong to
1731 * @sta_flags_mask: station flags that changed
1732 * (bitmask of BIT(%NL80211_STA_FLAG_...))
1733 * @sta_flags_set: station flags values
1734 * (bitmask of BIT(%NL80211_STA_FLAG_...))
1735 * @listen_interval: listen interval or -1 for no change
1736 * @aid: AID or zero for no change
1737 * @vlan_id: VLAN ID for station (if nonzero)
1738 * @peer_aid: mesh peer AID or zero for no change
1739 * @plink_action: plink action to take
1740 * @plink_state: set the peer link state for a station
1741 * @uapsd_queues: bitmap of queues configured for uapsd. same format
1742 * as the AC bitmap in the QoS info field
1743 * @max_sp: max Service Period. same format as the MAX_SP in the
1744 * QoS info field (but already shifted down)
1745 * @sta_modify_mask: bitmap indicating which parameters changed
1746 * (for those that don't have a natural "no change" value),
1747 * see &enum station_parameters_apply_mask
1748 * @local_pm: local link-specific mesh power save mode (no change when set
1749 * to unknown)
1750 * @capability: station capability
1751 * @ext_capab: extended capabilities of the station
1752 * @ext_capab_len: number of extended capabilities
1753 * @supported_channels: supported channels in IEEE 802.11 format
1754 * @supported_channels_len: number of supported channels
1755 * @supported_oper_classes: supported oper classes in IEEE 802.11 format
1756 * @supported_oper_classes_len: number of supported operating classes
1757 * @support_p2p_ps: information if station supports P2P PS mechanism
1758 * @airtime_weight: airtime scheduler weight for this station
1759 * @link_sta_params: link related params.
1760 */
1761struct station_parameters {
1762 struct net_device *vlan;
1763 u32 sta_flags_mask, sta_flags_set;
1764 u32 sta_modify_mask;
1765 int listen_interval;
1766 u16 aid;
1767 u16 vlan_id;
1768 u16 peer_aid;
1769 u8 plink_action;
1770 u8 plink_state;
1771 u8 uapsd_queues;
1772 u8 max_sp;
1773 enum nl80211_mesh_power_mode local_pm;
1774 u16 capability;
1775 const u8 *ext_capab;
1776 u8 ext_capab_len;
1777 const u8 *supported_channels;
1778 u8 supported_channels_len;
1779 const u8 *supported_oper_classes;
1780 u8 supported_oper_classes_len;
1781 int support_p2p_ps;
1782 u16 airtime_weight;
1783 struct link_station_parameters link_sta_params;
1784};
1785
1786/**
1787 * struct station_del_parameters - station deletion parameters
1788 *
1789 * Used to delete a station entry (or all stations).
1790 *
1791 * @mac: MAC address of the station to remove or NULL to remove all stations
1792 * @subtype: Management frame subtype to use for indicating removal
1793 * (10 = Disassociation, 12 = Deauthentication)
1794 * @reason_code: Reason code for the Disassociation/Deauthentication frame
1795 * @link_id: Link ID indicating a link that stations to be flushed must be
1796 * using; valid only for MLO, but can also be -1 for MLO to really
1797 * remove all stations.
1798 */
1799struct station_del_parameters {
1800 const u8 *mac;
1801 u8 subtype;
1802 u16 reason_code;
1803 int link_id;
1804};
1805
1806/**
1807 * enum cfg80211_station_type - the type of station being modified
1808 * @CFG80211_STA_AP_CLIENT: client of an AP interface
1809 * @CFG80211_STA_AP_CLIENT_UNASSOC: client of an AP interface that is still
1810 * unassociated (update properties for this type of client is permitted)
1811 * @CFG80211_STA_AP_MLME_CLIENT: client of an AP interface that has
1812 * the AP MLME in the device
1813 * @CFG80211_STA_AP_STA: AP station on managed interface
1814 * @CFG80211_STA_IBSS: IBSS station
1815 * @CFG80211_STA_TDLS_PEER_SETUP: TDLS peer on managed interface (dummy entry
1816 * while TDLS setup is in progress, it moves out of this state when
1817 * being marked authorized; use this only if TDLS with external setup is
1818 * supported/used)
1819 * @CFG80211_STA_TDLS_PEER_ACTIVE: TDLS peer on managed interface (active
1820 * entry that is operating, has been marked authorized by userspace)
1821 * @CFG80211_STA_MESH_PEER_KERNEL: peer on mesh interface (kernel managed)
1822 * @CFG80211_STA_MESH_PEER_USER: peer on mesh interface (user managed)
1823 */
1824enum cfg80211_station_type {
1825 CFG80211_STA_AP_CLIENT,
1826 CFG80211_STA_AP_CLIENT_UNASSOC,
1827 CFG80211_STA_AP_MLME_CLIENT,
1828 CFG80211_STA_AP_STA,
1829 CFG80211_STA_IBSS,
1830 CFG80211_STA_TDLS_PEER_SETUP,
1831 CFG80211_STA_TDLS_PEER_ACTIVE,
1832 CFG80211_STA_MESH_PEER_KERNEL,
1833 CFG80211_STA_MESH_PEER_USER,
1834};
1835
1836/**
1837 * cfg80211_check_station_change - validate parameter changes
1838 * @wiphy: the wiphy this operates on
1839 * @params: the new parameters for a station
1840 * @statype: the type of station being modified
1841 *
1842 * Utility function for the @change_station driver method. Call this function
1843 * with the appropriate station type looking up the station (and checking that
1844 * it exists). It will verify whether the station change is acceptable.
1845 *
1846 * Return: 0 if the change is acceptable, otherwise an error code. Note that
1847 * it may modify the parameters for backward compatibility reasons, so don't
1848 * use them before calling this.
1849 */
1850int cfg80211_check_station_change(struct wiphy *wiphy,
1851 struct station_parameters *params,
1852 enum cfg80211_station_type statype);
1853
1854/**
1855 * enum rate_info_flags - bitrate info flags
1856 *
1857 * Used by the driver to indicate the specific rate transmission
1858 * type for 802.11n transmissions.
1859 *
1860 * @RATE_INFO_FLAGS_MCS: mcs field filled with HT MCS
1861 * @RATE_INFO_FLAGS_VHT_MCS: mcs field filled with VHT MCS
1862 * @RATE_INFO_FLAGS_SHORT_GI: 400ns guard interval
1863 * @RATE_INFO_FLAGS_DMG: 60GHz MCS
1864 * @RATE_INFO_FLAGS_HE_MCS: HE MCS information
1865 * @RATE_INFO_FLAGS_EDMG: 60GHz MCS in EDMG mode
1866 * @RATE_INFO_FLAGS_EXTENDED_SC_DMG: 60GHz extended SC MCS
1867 * @RATE_INFO_FLAGS_EHT_MCS: EHT MCS information
1868 * @RATE_INFO_FLAGS_S1G_MCS: MCS field filled with S1G MCS
1869 */
1870enum rate_info_flags {
1871 RATE_INFO_FLAGS_MCS = BIT(0),
1872 RATE_INFO_FLAGS_VHT_MCS = BIT(1),
1873 RATE_INFO_FLAGS_SHORT_GI = BIT(2),
1874 RATE_INFO_FLAGS_DMG = BIT(3),
1875 RATE_INFO_FLAGS_HE_MCS = BIT(4),
1876 RATE_INFO_FLAGS_EDMG = BIT(5),
1877 RATE_INFO_FLAGS_EXTENDED_SC_DMG = BIT(6),
1878 RATE_INFO_FLAGS_EHT_MCS = BIT(7),
1879 RATE_INFO_FLAGS_S1G_MCS = BIT(8),
1880};
1881
1882/**
1883 * enum rate_info_bw - rate bandwidth information
1884 *
1885 * Used by the driver to indicate the rate bandwidth.
1886 *
1887 * @RATE_INFO_BW_5: 5 MHz bandwidth
1888 * @RATE_INFO_BW_10: 10 MHz bandwidth
1889 * @RATE_INFO_BW_20: 20 MHz bandwidth
1890 * @RATE_INFO_BW_40: 40 MHz bandwidth
1891 * @RATE_INFO_BW_80: 80 MHz bandwidth
1892 * @RATE_INFO_BW_160: 160 MHz bandwidth
1893 * @RATE_INFO_BW_HE_RU: bandwidth determined by HE RU allocation
1894 * @RATE_INFO_BW_320: 320 MHz bandwidth
1895 * @RATE_INFO_BW_EHT_RU: bandwidth determined by EHT RU allocation
1896 * @RATE_INFO_BW_1: 1 MHz bandwidth
1897 * @RATE_INFO_BW_2: 2 MHz bandwidth
1898 * @RATE_INFO_BW_4: 4 MHz bandwidth
1899 * @RATE_INFO_BW_8: 8 MHz bandwidth
1900 * @RATE_INFO_BW_16: 16 MHz bandwidth
1901 */
1902enum rate_info_bw {
1903 RATE_INFO_BW_20 = 0,
1904 RATE_INFO_BW_5,
1905 RATE_INFO_BW_10,
1906 RATE_INFO_BW_40,
1907 RATE_INFO_BW_80,
1908 RATE_INFO_BW_160,
1909 RATE_INFO_BW_HE_RU,
1910 RATE_INFO_BW_320,
1911 RATE_INFO_BW_EHT_RU,
1912 RATE_INFO_BW_1,
1913 RATE_INFO_BW_2,
1914 RATE_INFO_BW_4,
1915 RATE_INFO_BW_8,
1916 RATE_INFO_BW_16,
1917};
1918
1919/**
1920 * struct rate_info - bitrate information
1921 *
1922 * Information about a receiving or transmitting bitrate
1923 *
1924 * @flags: bitflag of flags from &enum rate_info_flags
1925 * @legacy: bitrate in 100kbit/s for 802.11abg
1926 * @mcs: mcs index if struct describes an HT/VHT/HE/EHT/S1G rate
1927 * @nss: number of streams (VHT & HE only)
1928 * @bw: bandwidth (from &enum rate_info_bw)
1929 * @he_gi: HE guard interval (from &enum nl80211_he_gi)
1930 * @he_dcm: HE DCM value
1931 * @he_ru_alloc: HE RU allocation (from &enum nl80211_he_ru_alloc,
1932 * only valid if bw is %RATE_INFO_BW_HE_RU)
1933 * @n_bonded_ch: In case of EDMG the number of bonded channels (1-4)
1934 * @eht_gi: EHT guard interval (from &enum nl80211_eht_gi)
1935 * @eht_ru_alloc: EHT RU allocation (from &enum nl80211_eht_ru_alloc,
1936 * only valid if bw is %RATE_INFO_BW_EHT_RU)
1937 */
1938struct rate_info {
1939 u16 flags;
1940 u16 legacy;
1941 u8 mcs;
1942 u8 nss;
1943 u8 bw;
1944 u8 he_gi;
1945 u8 he_dcm;
1946 u8 he_ru_alloc;
1947 u8 n_bonded_ch;
1948 u8 eht_gi;
1949 u8 eht_ru_alloc;
1950};
1951
1952/**
1953 * enum bss_param_flags - bitrate info flags
1954 *
1955 * Used by the driver to indicate the specific rate transmission
1956 * type for 802.11n transmissions.
1957 *
1958 * @BSS_PARAM_FLAGS_CTS_PROT: whether CTS protection is enabled
1959 * @BSS_PARAM_FLAGS_SHORT_PREAMBLE: whether short preamble is enabled
1960 * @BSS_PARAM_FLAGS_SHORT_SLOT_TIME: whether short slot time is enabled
1961 */
1962enum bss_param_flags {
1963 BSS_PARAM_FLAGS_CTS_PROT = BIT(0),
1964 BSS_PARAM_FLAGS_SHORT_PREAMBLE = BIT(1),
1965 BSS_PARAM_FLAGS_SHORT_SLOT_TIME = BIT(2),
1966};
1967
1968/**
1969 * struct sta_bss_parameters - BSS parameters for the attached station
1970 *
1971 * Information about the currently associated BSS
1972 *
1973 * @flags: bitflag of flags from &enum bss_param_flags
1974 * @dtim_period: DTIM period for the BSS
1975 * @beacon_interval: beacon interval
1976 */
1977struct sta_bss_parameters {
1978 u8 flags;
1979 u8 dtim_period;
1980 u16 beacon_interval;
1981};
1982
1983/**
1984 * struct cfg80211_txq_stats - TXQ statistics for this TID
1985 * @filled: bitmap of flags using the bits of &enum nl80211_txq_stats to
1986 * indicate the relevant values in this struct are filled
1987 * @backlog_bytes: total number of bytes currently backlogged
1988 * @backlog_packets: total number of packets currently backlogged
1989 * @flows: number of new flows seen
1990 * @drops: total number of packets dropped
1991 * @ecn_marks: total number of packets marked with ECN CE
1992 * @overlimit: number of drops due to queue space overflow
1993 * @overmemory: number of drops due to memory limit overflow
1994 * @collisions: number of hash collisions
1995 * @tx_bytes: total number of bytes dequeued
1996 * @tx_packets: total number of packets dequeued
1997 * @max_flows: maximum number of flows supported
1998 */
1999struct cfg80211_txq_stats {
2000 u32 filled;
2001 u32 backlog_bytes;
2002 u32 backlog_packets;
2003 u32 flows;
2004 u32 drops;
2005 u32 ecn_marks;
2006 u32 overlimit;
2007 u32 overmemory;
2008 u32 collisions;
2009 u32 tx_bytes;
2010 u32 tx_packets;
2011 u32 max_flows;
2012};
2013
2014/**
2015 * struct cfg80211_tid_stats - per-TID statistics
2016 * @filled: bitmap of flags using the bits of &enum nl80211_tid_stats to
2017 * indicate the relevant values in this struct are filled
2018 * @rx_msdu: number of received MSDUs
2019 * @tx_msdu: number of (attempted) transmitted MSDUs
2020 * @tx_msdu_retries: number of retries (not counting the first) for
2021 * transmitted MSDUs
2022 * @tx_msdu_failed: number of failed transmitted MSDUs
2023 * @txq_stats: TXQ statistics
2024 */
2025struct cfg80211_tid_stats {
2026 u32 filled;
2027 u64 rx_msdu;
2028 u64 tx_msdu;
2029 u64 tx_msdu_retries;
2030 u64 tx_msdu_failed;
2031 struct cfg80211_txq_stats txq_stats;
2032};
2033
2034#define IEEE80211_MAX_CHAINS 4
2035
2036/**
2037 * struct station_info - station information
2038 *
2039 * Station information filled by driver for get_station() and dump_station.
2040 *
2041 * @filled: bitflag of flags using the bits of &enum nl80211_sta_info to
2042 * indicate the relevant values in this struct for them
2043 * @connected_time: time(in secs) since a station is last connected
2044 * @inactive_time: time since last station activity (tx/rx) in milliseconds
2045 * @assoc_at: bootime (ns) of the last association
2046 * @rx_bytes: bytes (size of MPDUs) received from this station
2047 * @tx_bytes: bytes (size of MPDUs) transmitted to this station
2048 * @llid: mesh local link id
2049 * @plid: mesh peer link id
2050 * @plink_state: mesh peer link state
2051 * @signal: The signal strength, type depends on the wiphy's signal_type.
2052 * For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_.
2053 * @signal_avg: Average signal strength, type depends on the wiphy's signal_type.
2054 * For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_.
2055 * @chains: bitmask for filled values in @chain_signal, @chain_signal_avg
2056 * @chain_signal: per-chain signal strength of last received packet in dBm
2057 * @chain_signal_avg: per-chain signal strength average in dBm
2058 * @txrate: current unicast bitrate from this station
2059 * @rxrate: current unicast bitrate to this station
2060 * @rx_packets: packets (MSDUs & MMPDUs) received from this station
2061 * @tx_packets: packets (MSDUs & MMPDUs) transmitted to this station
2062 * @tx_retries: cumulative retry counts (MPDUs)
2063 * @tx_failed: number of failed transmissions (MPDUs) (retries exceeded, no ACK)
2064 * @rx_dropped_misc: Dropped for un-specified reason.
2065 * @bss_param: current BSS parameters
2066 * @generation: generation number for nl80211 dumps.
2067 * This number should increase every time the list of stations
2068 * changes, i.e. when a station is added or removed, so that
2069 * userspace can tell whether it got a consistent snapshot.
2070 * @assoc_req_ies: IEs from (Re)Association Request.
2071 * This is used only when in AP mode with drivers that do not use
2072 * user space MLME/SME implementation. The information is provided for
2073 * the cfg80211_new_sta() calls to notify user space of the IEs.
2074 * @assoc_req_ies_len: Length of assoc_req_ies buffer in octets.
2075 * @sta_flags: station flags mask & values
2076 * @beacon_loss_count: Number of times beacon loss event has triggered.
2077 * @t_offset: Time offset of the station relative to this host.
2078 * @local_pm: local mesh STA power save mode
2079 * @peer_pm: peer mesh STA power save mode
2080 * @nonpeer_pm: non-peer mesh STA power save mode
2081 * @expected_throughput: expected throughput in kbps (including 802.11 headers)
2082 * towards this station.
2083 * @rx_beacon: number of beacons received from this peer
2084 * @rx_beacon_signal_avg: signal strength average (in dBm) for beacons received
2085 * from this peer
2086 * @connected_to_gate: true if mesh STA has a path to mesh gate
2087 * @rx_duration: aggregate PPDU duration(usecs) for all the frames from a peer
2088 * @tx_duration: aggregate PPDU duration(usecs) for all the frames to a peer
2089 * @airtime_weight: current airtime scheduling weight
2090 * @pertid: per-TID statistics, see &struct cfg80211_tid_stats, using the last
2091 * (IEEE80211_NUM_TIDS) index for MSDUs not encapsulated in QoS-MPDUs.
2092 * Note that this doesn't use the @filled bit, but is used if non-NULL.
2093 * @ack_signal: signal strength (in dBm) of the last ACK frame.
2094 * @avg_ack_signal: average rssi value of ack packet for the no of msdu's has
2095 * been sent.
2096 * @rx_mpdu_count: number of MPDUs received from this station
2097 * @fcs_err_count: number of packets (MPDUs) received from this station with
2098 * an FCS error. This counter should be incremented only when TA of the
2099 * received packet with an FCS error matches the peer MAC address.
2100 * @airtime_link_metric: mesh airtime link metric.
2101 * @connected_to_as: true if mesh STA has a path to authentication server
2102 * @mlo_params_valid: Indicates @assoc_link_id and @mld_addr fields are filled
2103 * by driver. Drivers use this only in cfg80211_new_sta() calls when AP
2104 * MLD's MLME/SME is offload to driver. Drivers won't fill this
2105 * information in cfg80211_del_sta_sinfo(), get_station() and
2106 * dump_station() callbacks.
2107 * @assoc_link_id: Indicates MLO link ID of the AP, with which the station
2108 * completed (re)association. This information filled for both MLO
2109 * and non-MLO STA connections when the AP affiliated with an MLD.
2110 * @mld_addr: For MLO STA connection, filled with MLD address of the station.
2111 * For non-MLO STA connection, filled with all zeros.
2112 * @assoc_resp_ies: IEs from (Re)Association Response.
2113 * This is used only when in AP mode with drivers that do not use user
2114 * space MLME/SME implementation. The information is provided only for the
2115 * cfg80211_new_sta() calls to notify user space of the IEs. Drivers won't
2116 * fill this information in cfg80211_del_sta_sinfo(), get_station() and
2117 * dump_station() callbacks. User space needs this information to determine
2118 * the accepted and rejected affiliated links of the connected station.
2119 * @assoc_resp_ies_len: Length of @assoc_resp_ies buffer in octets.
2120 */
2121struct station_info {
2122 u64 filled;
2123 u32 connected_time;
2124 u32 inactive_time;
2125 u64 assoc_at;
2126 u64 rx_bytes;
2127 u64 tx_bytes;
2128 u16 llid;
2129 u16 plid;
2130 u8 plink_state;
2131 s8 signal;
2132 s8 signal_avg;
2133
2134 u8 chains;
2135 s8 chain_signal[IEEE80211_MAX_CHAINS];
2136 s8 chain_signal_avg[IEEE80211_MAX_CHAINS];
2137
2138 struct rate_info txrate;
2139 struct rate_info rxrate;
2140 u32 rx_packets;
2141 u32 tx_packets;
2142 u32 tx_retries;
2143 u32 tx_failed;
2144 u32 rx_dropped_misc;
2145 struct sta_bss_parameters bss_param;
2146 struct nl80211_sta_flag_update sta_flags;
2147
2148 int generation;
2149
2150 const u8 *assoc_req_ies;
2151 size_t assoc_req_ies_len;
2152
2153 u32 beacon_loss_count;
2154 s64 t_offset;
2155 enum nl80211_mesh_power_mode local_pm;
2156 enum nl80211_mesh_power_mode peer_pm;
2157 enum nl80211_mesh_power_mode nonpeer_pm;
2158
2159 u32 expected_throughput;
2160
2161 u64 tx_duration;
2162 u64 rx_duration;
2163 u64 rx_beacon;
2164 u8 rx_beacon_signal_avg;
2165 u8 connected_to_gate;
2166
2167 struct cfg80211_tid_stats *pertid;
2168 s8 ack_signal;
2169 s8 avg_ack_signal;
2170
2171 u16 airtime_weight;
2172
2173 u32 rx_mpdu_count;
2174 u32 fcs_err_count;
2175
2176 u32 airtime_link_metric;
2177
2178 u8 connected_to_as;
2179
2180 bool mlo_params_valid;
2181 u8 assoc_link_id;
2182 u8 mld_addr[ETH_ALEN] __aligned(2);
2183 const u8 *assoc_resp_ies;
2184 size_t assoc_resp_ies_len;
2185};
2186
2187/**
2188 * struct cfg80211_sar_sub_specs - sub specs limit
2189 * @power: power limitation in 0.25dbm
2190 * @freq_range_index: index the power limitation applies to
2191 */
2192struct cfg80211_sar_sub_specs {
2193 s32 power;
2194 u32 freq_range_index;
2195};
2196
2197/**
2198 * struct cfg80211_sar_specs - sar limit specs
2199 * @type: it's set with power in 0.25dbm or other types
2200 * @num_sub_specs: number of sar sub specs
2201 * @sub_specs: memory to hold the sar sub specs
2202 */
2203struct cfg80211_sar_specs {
2204 enum nl80211_sar_type type;
2205 u32 num_sub_specs;
2206 struct cfg80211_sar_sub_specs sub_specs[] __counted_by(num_sub_specs);
2207};
2208
2209
2210/**
2211 * struct cfg80211_sar_freq_ranges - sar frequency ranges
2212 * @start_freq: start range edge frequency
2213 * @end_freq: end range edge frequency
2214 */
2215struct cfg80211_sar_freq_ranges {
2216 u32 start_freq;
2217 u32 end_freq;
2218};
2219
2220/**
2221 * struct cfg80211_sar_capa - sar limit capability
2222 * @type: it's set via power in 0.25dbm or other types
2223 * @num_freq_ranges: number of frequency ranges
2224 * @freq_ranges: memory to hold the freq ranges.
2225 *
2226 * Note: WLAN driver may append new ranges or split an existing
2227 * range to small ones and then append them.
2228 */
2229struct cfg80211_sar_capa {
2230 enum nl80211_sar_type type;
2231 u32 num_freq_ranges;
2232 const struct cfg80211_sar_freq_ranges *freq_ranges;
2233};
2234
2235#if IS_ENABLED(CONFIG_CFG80211)
2236/**
2237 * cfg80211_get_station - retrieve information about a given station
2238 * @dev: the device where the station is supposed to be connected to
2239 * @mac_addr: the mac address of the station of interest
2240 * @sinfo: pointer to the structure to fill with the information
2241 *
2242 * Return: 0 on success and sinfo is filled with the available information
2243 * otherwise returns a negative error code and the content of sinfo has to be
2244 * considered undefined.
2245 */
2246int cfg80211_get_station(struct net_device *dev, const u8 *mac_addr,
2247 struct station_info *sinfo);
2248#else
2249static inline int cfg80211_get_station(struct net_device *dev,
2250 const u8 *mac_addr,
2251 struct station_info *sinfo)
2252{
2253 return -ENOENT;
2254}
2255#endif
2256
2257/**
2258 * enum monitor_flags - monitor flags
2259 *
2260 * Monitor interface configuration flags. Note that these must be the bits
2261 * according to the nl80211 flags.
2262 *
2263 * @MONITOR_FLAG_CHANGED: set if the flags were changed
2264 * @MONITOR_FLAG_FCSFAIL: pass frames with bad FCS
2265 * @MONITOR_FLAG_PLCPFAIL: pass frames with bad PLCP
2266 * @MONITOR_FLAG_CONTROL: pass control frames
2267 * @MONITOR_FLAG_OTHER_BSS: disable BSSID filtering
2268 * @MONITOR_FLAG_COOK_FRAMES: report frames after processing
2269 * @MONITOR_FLAG_ACTIVE: active monitor, ACKs frames on its MAC address
2270 * @MONITOR_FLAG_SKIP_TX: do not pass locally transmitted frames
2271 */
2272enum monitor_flags {
2273 MONITOR_FLAG_CHANGED = BIT(__NL80211_MNTR_FLAG_INVALID),
2274 MONITOR_FLAG_FCSFAIL = BIT(NL80211_MNTR_FLAG_FCSFAIL),
2275 MONITOR_FLAG_PLCPFAIL = BIT(NL80211_MNTR_FLAG_PLCPFAIL),
2276 MONITOR_FLAG_CONTROL = BIT(NL80211_MNTR_FLAG_CONTROL),
2277 MONITOR_FLAG_OTHER_BSS = BIT(NL80211_MNTR_FLAG_OTHER_BSS),
2278 MONITOR_FLAG_COOK_FRAMES = BIT(NL80211_MNTR_FLAG_COOK_FRAMES),
2279 MONITOR_FLAG_ACTIVE = BIT(NL80211_MNTR_FLAG_ACTIVE),
2280 MONITOR_FLAG_SKIP_TX = BIT(NL80211_MNTR_FLAG_SKIP_TX),
2281};
2282
2283/**
2284 * enum mpath_info_flags - mesh path information flags
2285 *
2286 * Used by the driver to indicate which info in &struct mpath_info it has filled
2287 * in during get_station() or dump_station().
2288 *
2289 * @MPATH_INFO_FRAME_QLEN: @frame_qlen filled
2290 * @MPATH_INFO_SN: @sn filled
2291 * @MPATH_INFO_METRIC: @metric filled
2292 * @MPATH_INFO_EXPTIME: @exptime filled
2293 * @MPATH_INFO_DISCOVERY_TIMEOUT: @discovery_timeout filled
2294 * @MPATH_INFO_DISCOVERY_RETRIES: @discovery_retries filled
2295 * @MPATH_INFO_FLAGS: @flags filled
2296 * @MPATH_INFO_HOP_COUNT: @hop_count filled
2297 * @MPATH_INFO_PATH_CHANGE: @path_change_count filled
2298 */
2299enum mpath_info_flags {
2300 MPATH_INFO_FRAME_QLEN = BIT(0),
2301 MPATH_INFO_SN = BIT(1),
2302 MPATH_INFO_METRIC = BIT(2),
2303 MPATH_INFO_EXPTIME = BIT(3),
2304 MPATH_INFO_DISCOVERY_TIMEOUT = BIT(4),
2305 MPATH_INFO_DISCOVERY_RETRIES = BIT(5),
2306 MPATH_INFO_FLAGS = BIT(6),
2307 MPATH_INFO_HOP_COUNT = BIT(7),
2308 MPATH_INFO_PATH_CHANGE = BIT(8),
2309};
2310
2311/**
2312 * struct mpath_info - mesh path information
2313 *
2314 * Mesh path information filled by driver for get_mpath() and dump_mpath().
2315 *
2316 * @filled: bitfield of flags from &enum mpath_info_flags
2317 * @frame_qlen: number of queued frames for this destination
2318 * @sn: target sequence number
2319 * @metric: metric (cost) of this mesh path
2320 * @exptime: expiration time for the mesh path from now, in msecs
2321 * @flags: mesh path flags from &enum mesh_path_flags
2322 * @discovery_timeout: total mesh path discovery timeout, in msecs
2323 * @discovery_retries: mesh path discovery retries
2324 * @generation: generation number for nl80211 dumps.
2325 * This number should increase every time the list of mesh paths
2326 * changes, i.e. when a station is added or removed, so that
2327 * userspace can tell whether it got a consistent snapshot.
2328 * @hop_count: hops to destination
2329 * @path_change_count: total number of path changes to destination
2330 */
2331struct mpath_info {
2332 u32 filled;
2333 u32 frame_qlen;
2334 u32 sn;
2335 u32 metric;
2336 u32 exptime;
2337 u32 discovery_timeout;
2338 u8 discovery_retries;
2339 u8 flags;
2340 u8 hop_count;
2341 u32 path_change_count;
2342
2343 int generation;
2344};
2345
2346/**
2347 * struct bss_parameters - BSS parameters
2348 *
2349 * Used to change BSS parameters (mainly for AP mode).
2350 *
2351 * @link_id: link_id or -1 for non-MLD
2352 * @use_cts_prot: Whether to use CTS protection
2353 * (0 = no, 1 = yes, -1 = do not change)
2354 * @use_short_preamble: Whether the use of short preambles is allowed
2355 * (0 = no, 1 = yes, -1 = do not change)
2356 * @use_short_slot_time: Whether the use of short slot time is allowed
2357 * (0 = no, 1 = yes, -1 = do not change)
2358 * @basic_rates: basic rates in IEEE 802.11 format
2359 * (or NULL for no change)
2360 * @basic_rates_len: number of basic rates
2361 * @ap_isolate: do not forward packets between connected stations
2362 * (0 = no, 1 = yes, -1 = do not change)
2363 * @ht_opmode: HT Operation mode
2364 * (u16 = opmode, -1 = do not change)
2365 * @p2p_ctwindow: P2P CT Window (-1 = no change)
2366 * @p2p_opp_ps: P2P opportunistic PS (-1 = no change)
2367 */
2368struct bss_parameters {
2369 int link_id;
2370 int use_cts_prot;
2371 int use_short_preamble;
2372 int use_short_slot_time;
2373 const u8 *basic_rates;
2374 u8 basic_rates_len;
2375 int ap_isolate;
2376 int ht_opmode;
2377 s8 p2p_ctwindow, p2p_opp_ps;
2378};
2379
2380/**
2381 * struct mesh_config - 802.11s mesh configuration
2382 *
2383 * These parameters can be changed while the mesh is active.
2384 *
2385 * @dot11MeshRetryTimeout: the initial retry timeout in millisecond units used
2386 * by the Mesh Peering Open message
2387 * @dot11MeshConfirmTimeout: the initial retry timeout in millisecond units
2388 * used by the Mesh Peering Open message
2389 * @dot11MeshHoldingTimeout: the confirm timeout in millisecond units used by
2390 * the mesh peering management to close a mesh peering
2391 * @dot11MeshMaxPeerLinks: the maximum number of peer links allowed on this
2392 * mesh interface
2393 * @dot11MeshMaxRetries: the maximum number of peer link open retries that can
2394 * be sent to establish a new peer link instance in a mesh
2395 * @dot11MeshTTL: the value of TTL field set at a source mesh STA
2396 * @element_ttl: the value of TTL field set at a mesh STA for path selection
2397 * elements
2398 * @auto_open_plinks: whether we should automatically open peer links when we
2399 * detect compatible mesh peers
2400 * @dot11MeshNbrOffsetMaxNeighbor: the maximum number of neighbors to
2401 * synchronize to for 11s default synchronization method
2402 * @dot11MeshHWMPmaxPREQretries: the number of action frames containing a PREQ
2403 * that an originator mesh STA can send to a particular path target
2404 * @path_refresh_time: how frequently to refresh mesh paths in milliseconds
2405 * @min_discovery_timeout: the minimum length of time to wait until giving up on
2406 * a path discovery in milliseconds
2407 * @dot11MeshHWMPactivePathTimeout: the time (in TUs) for which mesh STAs
2408 * receiving a PREQ shall consider the forwarding information from the
2409 * root to be valid. (TU = time unit)
2410 * @dot11MeshHWMPpreqMinInterval: the minimum interval of time (in TUs) during
2411 * which a mesh STA can send only one action frame containing a PREQ
2412 * element
2413 * @dot11MeshHWMPperrMinInterval: the minimum interval of time (in TUs) during
2414 * which a mesh STA can send only one Action frame containing a PERR
2415 * element
2416 * @dot11MeshHWMPnetDiameterTraversalTime: the interval of time (in TUs) that
2417 * it takes for an HWMP information element to propagate across the mesh
2418 * @dot11MeshHWMPRootMode: the configuration of a mesh STA as root mesh STA
2419 * @dot11MeshHWMPRannInterval: the interval of time (in TUs) between root
2420 * announcements are transmitted
2421 * @dot11MeshGateAnnouncementProtocol: whether to advertise that this mesh
2422 * station has access to a broader network beyond the MBSS. (This is
2423 * missnamed in draft 12.0: dot11MeshGateAnnouncementProtocol set to true
2424 * only means that the station will announce others it's a mesh gate, but
2425 * not necessarily using the gate announcement protocol. Still keeping the
2426 * same nomenclature to be in sync with the spec)
2427 * @dot11MeshForwarding: whether the Mesh STA is forwarding or non-forwarding
2428 * entity (default is TRUE - forwarding entity)
2429 * @rssi_threshold: the threshold for average signal strength of candidate
2430 * station to establish a peer link
2431 * @ht_opmode: mesh HT protection mode
2432 *
2433 * @dot11MeshHWMPactivePathToRootTimeout: The time (in TUs) for which mesh STAs
2434 * receiving a proactive PREQ shall consider the forwarding information to
2435 * the root mesh STA to be valid.
2436 *
2437 * @dot11MeshHWMProotInterval: The interval of time (in TUs) between proactive
2438 * PREQs are transmitted.
2439 * @dot11MeshHWMPconfirmationInterval: The minimum interval of time (in TUs)
2440 * during which a mesh STA can send only one Action frame containing
2441 * a PREQ element for root path confirmation.
2442 * @power_mode: The default mesh power save mode which will be the initial
2443 * setting for new peer links.
2444 * @dot11MeshAwakeWindowDuration: The duration in TUs the STA will remain awake
2445 * after transmitting its beacon.
2446 * @plink_timeout: If no tx activity is seen from a STA we've established
2447 * peering with for longer than this time (in seconds), then remove it
2448 * from the STA's list of peers. Default is 30 minutes.
2449 * @dot11MeshConnectedToAuthServer: if set to true then this mesh STA
2450 * will advertise that it is connected to a authentication server
2451 * in the mesh formation field.
2452 * @dot11MeshConnectedToMeshGate: if set to true, advertise that this STA is
2453 * connected to a mesh gate in mesh formation info. If false, the
2454 * value in mesh formation is determined by the presence of root paths
2455 * in the mesh path table
2456 * @dot11MeshNolearn: Try to avoid multi-hop path discovery (e.g. PREQ/PREP
2457 * for HWMP) if the destination is a direct neighbor. Note that this might
2458 * not be the optimal decision as a multi-hop route might be better. So
2459 * if using this setting you will likely also want to disable
2460 * dot11MeshForwarding and use another mesh routing protocol on top.
2461 */
2462struct mesh_config {
2463 u16 dot11MeshRetryTimeout;
2464 u16 dot11MeshConfirmTimeout;
2465 u16 dot11MeshHoldingTimeout;
2466 u16 dot11MeshMaxPeerLinks;
2467 u8 dot11MeshMaxRetries;
2468 u8 dot11MeshTTL;
2469 u8 element_ttl;
2470 bool auto_open_plinks;
2471 u32 dot11MeshNbrOffsetMaxNeighbor;
2472 u8 dot11MeshHWMPmaxPREQretries;
2473 u32 path_refresh_time;
2474 u16 min_discovery_timeout;
2475 u32 dot11MeshHWMPactivePathTimeout;
2476 u16 dot11MeshHWMPpreqMinInterval;
2477 u16 dot11MeshHWMPperrMinInterval;
2478 u16 dot11MeshHWMPnetDiameterTraversalTime;
2479 u8 dot11MeshHWMPRootMode;
2480 bool dot11MeshConnectedToMeshGate;
2481 bool dot11MeshConnectedToAuthServer;
2482 u16 dot11MeshHWMPRannInterval;
2483 bool dot11MeshGateAnnouncementProtocol;
2484 bool dot11MeshForwarding;
2485 s32 rssi_threshold;
2486 u16 ht_opmode;
2487 u32 dot11MeshHWMPactivePathToRootTimeout;
2488 u16 dot11MeshHWMProotInterval;
2489 u16 dot11MeshHWMPconfirmationInterval;
2490 enum nl80211_mesh_power_mode power_mode;
2491 u16 dot11MeshAwakeWindowDuration;
2492 u32 plink_timeout;
2493 bool dot11MeshNolearn;
2494};
2495
2496/**
2497 * struct mesh_setup - 802.11s mesh setup configuration
2498 * @chandef: defines the channel to use
2499 * @mesh_id: the mesh ID
2500 * @mesh_id_len: length of the mesh ID, at least 1 and at most 32 bytes
2501 * @sync_method: which synchronization method to use
2502 * @path_sel_proto: which path selection protocol to use
2503 * @path_metric: which metric to use
2504 * @auth_id: which authentication method this mesh is using
2505 * @ie: vendor information elements (optional)
2506 * @ie_len: length of vendor information elements
2507 * @is_authenticated: this mesh requires authentication
2508 * @is_secure: this mesh uses security
2509 * @user_mpm: userspace handles all MPM functions
2510 * @dtim_period: DTIM period to use
2511 * @beacon_interval: beacon interval to use
2512 * @mcast_rate: multicast rate for Mesh Node [6Mbps is the default for 802.11a]
2513 * @basic_rates: basic rates to use when creating the mesh
2514 * @beacon_rate: bitrate to be used for beacons
2515 * @userspace_handles_dfs: whether user space controls DFS operation, i.e.
2516 * changes the channel when a radar is detected. This is required
2517 * to operate on DFS channels.
2518 * @control_port_over_nl80211: TRUE if userspace expects to exchange control
2519 * port frames over NL80211 instead of the network interface.
2520 *
2521 * These parameters are fixed when the mesh is created.
2522 */
2523struct mesh_setup {
2524 struct cfg80211_chan_def chandef;
2525 const u8 *mesh_id;
2526 u8 mesh_id_len;
2527 u8 sync_method;
2528 u8 path_sel_proto;
2529 u8 path_metric;
2530 u8 auth_id;
2531 const u8 *ie;
2532 u8 ie_len;
2533 bool is_authenticated;
2534 bool is_secure;
2535 bool user_mpm;
2536 u8 dtim_period;
2537 u16 beacon_interval;
2538 int mcast_rate[NUM_NL80211_BANDS];
2539 u32 basic_rates;
2540 struct cfg80211_bitrate_mask beacon_rate;
2541 bool userspace_handles_dfs;
2542 bool control_port_over_nl80211;
2543};
2544
2545/**
2546 * struct ocb_setup - 802.11p OCB mode setup configuration
2547 * @chandef: defines the channel to use
2548 *
2549 * These parameters are fixed when connecting to the network
2550 */
2551struct ocb_setup {
2552 struct cfg80211_chan_def chandef;
2553};
2554
2555/**
2556 * struct ieee80211_txq_params - TX queue parameters
2557 * @ac: AC identifier
2558 * @txop: Maximum burst time in units of 32 usecs, 0 meaning disabled
2559 * @cwmin: Minimum contention window [a value of the form 2^n-1 in the range
2560 * 1..32767]
2561 * @cwmax: Maximum contention window [a value of the form 2^n-1 in the range
2562 * 1..32767]
2563 * @aifs: Arbitration interframe space [0..255]
2564 * @link_id: link_id or -1 for non-MLD
2565 */
2566struct ieee80211_txq_params {
2567 enum nl80211_ac ac;
2568 u16 txop;
2569 u16 cwmin;
2570 u16 cwmax;
2571 u8 aifs;
2572 int link_id;
2573};
2574
2575/**
2576 * DOC: Scanning and BSS list handling
2577 *
2578 * The scanning process itself is fairly simple, but cfg80211 offers quite
2579 * a bit of helper functionality. To start a scan, the scan operation will
2580 * be invoked with a scan definition. This scan definition contains the
2581 * channels to scan, and the SSIDs to send probe requests for (including the
2582 * wildcard, if desired). A passive scan is indicated by having no SSIDs to
2583 * probe. Additionally, a scan request may contain extra information elements
2584 * that should be added to the probe request. The IEs are guaranteed to be
2585 * well-formed, and will not exceed the maximum length the driver advertised
2586 * in the wiphy structure.
2587 *
2588 * When scanning finds a BSS, cfg80211 needs to be notified of that, because
2589 * it is responsible for maintaining the BSS list; the driver should not
2590 * maintain a list itself. For this notification, various functions exist.
2591 *
2592 * Since drivers do not maintain a BSS list, there are also a number of
2593 * functions to search for a BSS and obtain information about it from the
2594 * BSS structure cfg80211 maintains. The BSS list is also made available
2595 * to userspace.
2596 */
2597
2598/**
2599 * struct cfg80211_ssid - SSID description
2600 * @ssid: the SSID
2601 * @ssid_len: length of the ssid
2602 */
2603struct cfg80211_ssid {
2604 u8 ssid[IEEE80211_MAX_SSID_LEN];
2605 u8 ssid_len;
2606};
2607
2608/**
2609 * struct cfg80211_scan_info - information about completed scan
2610 * @scan_start_tsf: scan start time in terms of the TSF of the BSS that the
2611 * wireless device that requested the scan is connected to. If this
2612 * information is not available, this field is left zero.
2613 * @tsf_bssid: the BSSID according to which %scan_start_tsf is set.
2614 * @aborted: set to true if the scan was aborted for any reason,
2615 * userspace will be notified of that
2616 */
2617struct cfg80211_scan_info {
2618 u64 scan_start_tsf;
2619 u8 tsf_bssid[ETH_ALEN] __aligned(2);
2620 bool aborted;
2621};
2622
2623/**
2624 * struct cfg80211_scan_6ghz_params - relevant for 6 GHz only
2625 *
2626 * @short_ssid: short ssid to scan for
2627 * @bssid: bssid to scan for
2628 * @channel_idx: idx of the channel in the channel array in the scan request
2629 * which the above info is relevant to
2630 * @unsolicited_probe: the AP transmits unsolicited probe response every 20 TU
2631 * @short_ssid_valid: @short_ssid is valid and can be used
2632 * @psc_no_listen: when set, and the channel is a PSC channel, no need to wait
2633 * 20 TUs before starting to send probe requests.
2634 * @psd_20: The AP's 20 MHz PSD value.
2635 */
2636struct cfg80211_scan_6ghz_params {
2637 u32 short_ssid;
2638 u32 channel_idx;
2639 u8 bssid[ETH_ALEN];
2640 bool unsolicited_probe;
2641 bool short_ssid_valid;
2642 bool psc_no_listen;
2643 s8 psd_20;
2644};
2645
2646/**
2647 * struct cfg80211_scan_request - scan request description
2648 *
2649 * @ssids: SSIDs to scan for (active scan only)
2650 * @n_ssids: number of SSIDs
2651 * @channels: channels to scan on.
2652 * @n_channels: total number of channels to scan
2653 * @ie: optional information element(s) to add into Probe Request or %NULL
2654 * @ie_len: length of ie in octets
2655 * @duration: how long to listen on each channel, in TUs. If
2656 * %duration_mandatory is not set, this is the maximum dwell time and
2657 * the actual dwell time may be shorter.
2658 * @duration_mandatory: if set, the scan duration must be as specified by the
2659 * %duration field.
2660 * @flags: control flags from &enum nl80211_scan_flags
2661 * @rates: bitmap of rates to advertise for each band
2662 * @wiphy: the wiphy this was for
2663 * @scan_start: time (in jiffies) when the scan started
2664 * @wdev: the wireless device to scan for
2665 * @info: (internal) information about completed scan
2666 * @notified: (internal) scan request was notified as done or aborted
2667 * @no_cck: used to send probe requests at non CCK rate in 2GHz band
2668 * @mac_addr: MAC address used with randomisation
2669 * @mac_addr_mask: MAC address mask used with randomisation, bits that
2670 * are 0 in the mask should be randomised, bits that are 1 should
2671 * be taken from the @mac_addr
2672 * @scan_6ghz: relevant for split scan request only,
2673 * true if this is the second scan request
2674 * @n_6ghz_params: number of 6 GHz params
2675 * @scan_6ghz_params: 6 GHz params
2676 * @bssid: BSSID to scan for (most commonly, the wildcard BSSID)
2677 * @tsf_report_link_id: for MLO, indicates the link ID of the BSS that should be
2678 * used for TSF reporting. Can be set to -1 to indicate no preference.
2679 */
2680struct cfg80211_scan_request {
2681 struct cfg80211_ssid *ssids;
2682 int n_ssids;
2683 u32 n_channels;
2684 const u8 *ie;
2685 size_t ie_len;
2686 u16 duration;
2687 bool duration_mandatory;
2688 u32 flags;
2689
2690 u32 rates[NUM_NL80211_BANDS];
2691
2692 struct wireless_dev *wdev;
2693
2694 u8 mac_addr[ETH_ALEN] __aligned(2);
2695 u8 mac_addr_mask[ETH_ALEN] __aligned(2);
2696 u8 bssid[ETH_ALEN] __aligned(2);
2697
2698 /* internal */
2699 struct wiphy *wiphy;
2700 unsigned long scan_start;
2701 struct cfg80211_scan_info info;
2702 bool notified;
2703 bool no_cck;
2704 bool scan_6ghz;
2705 u32 n_6ghz_params;
2706 struct cfg80211_scan_6ghz_params *scan_6ghz_params;
2707 s8 tsf_report_link_id;
2708
2709 /* keep last */
2710 struct ieee80211_channel *channels[] __counted_by(n_channels);
2711};
2712
2713static inline void get_random_mask_addr(u8 *buf, const u8 *addr, const u8 *mask)
2714{
2715 int i;
2716
2717 get_random_bytes(buf, ETH_ALEN);
2718 for (i = 0; i < ETH_ALEN; i++) {
2719 buf[i] &= ~mask[i];
2720 buf[i] |= addr[i] & mask[i];
2721 }
2722}
2723
2724/**
2725 * struct cfg80211_match_set - sets of attributes to match
2726 *
2727 * @ssid: SSID to be matched; may be zero-length in case of BSSID match
2728 * or no match (RSSI only)
2729 * @bssid: BSSID to be matched; may be all-zero BSSID in case of SSID match
2730 * or no match (RSSI only)
2731 * @rssi_thold: don't report scan results below this threshold (in s32 dBm)
2732 */
2733struct cfg80211_match_set {
2734 struct cfg80211_ssid ssid;
2735 u8 bssid[ETH_ALEN];
2736 s32 rssi_thold;
2737};
2738
2739/**
2740 * struct cfg80211_sched_scan_plan - scan plan for scheduled scan
2741 *
2742 * @interval: interval between scheduled scan iterations. In seconds.
2743 * @iterations: number of scan iterations in this scan plan. Zero means
2744 * infinite loop.
2745 * The last scan plan will always have this parameter set to zero,
2746 * all other scan plans will have a finite number of iterations.
2747 */
2748struct cfg80211_sched_scan_plan {
2749 u32 interval;
2750 u32 iterations;
2751};
2752
2753/**
2754 * struct cfg80211_bss_select_adjust - BSS selection with RSSI adjustment.
2755 *
2756 * @band: band of BSS which should match for RSSI level adjustment.
2757 * @delta: value of RSSI level adjustment.
2758 */
2759struct cfg80211_bss_select_adjust {
2760 enum nl80211_band band;
2761 s8 delta;
2762};
2763
2764/**
2765 * struct cfg80211_sched_scan_request - scheduled scan request description
2766 *
2767 * @reqid: identifies this request.
2768 * @ssids: SSIDs to scan for (passed in the probe_reqs in active scans)
2769 * @n_ssids: number of SSIDs
2770 * @n_channels: total number of channels to scan
2771 * @ie: optional information element(s) to add into Probe Request or %NULL
2772 * @ie_len: length of ie in octets
2773 * @flags: control flags from &enum nl80211_scan_flags
2774 * @match_sets: sets of parameters to be matched for a scan result
2775 * entry to be considered valid and to be passed to the host
2776 * (others are filtered out).
2777 * If omitted, all results are passed.
2778 * @n_match_sets: number of match sets
2779 * @report_results: indicates that results were reported for this request
2780 * @wiphy: the wiphy this was for
2781 * @dev: the interface
2782 * @scan_start: start time of the scheduled scan
2783 * @channels: channels to scan
2784 * @min_rssi_thold: for drivers only supporting a single threshold, this
2785 * contains the minimum over all matchsets
2786 * @mac_addr: MAC address used with randomisation
2787 * @mac_addr_mask: MAC address mask used with randomisation, bits that
2788 * are 0 in the mask should be randomised, bits that are 1 should
2789 * be taken from the @mac_addr
2790 * @scan_plans: scan plans to be executed in this scheduled scan. Lowest
2791 * index must be executed first.
2792 * @n_scan_plans: number of scan plans, at least 1.
2793 * @rcu_head: RCU callback used to free the struct
2794 * @owner_nlportid: netlink portid of owner (if this should is a request
2795 * owned by a particular socket)
2796 * @nl_owner_dead: netlink owner socket was closed - this request be freed
2797 * @list: for keeping list of requests.
2798 * @delay: delay in seconds to use before starting the first scan
2799 * cycle. The driver may ignore this parameter and start
2800 * immediately (or at any other time), if this feature is not
2801 * supported.
2802 * @relative_rssi_set: Indicates whether @relative_rssi is set or not.
2803 * @relative_rssi: Relative RSSI threshold in dB to restrict scan result
2804 * reporting in connected state to cases where a matching BSS is determined
2805 * to have better or slightly worse RSSI than the current connected BSS.
2806 * The relative RSSI threshold values are ignored in disconnected state.
2807 * @rssi_adjust: delta dB of RSSI preference to be given to the BSSs that belong
2808 * to the specified band while deciding whether a better BSS is reported
2809 * using @relative_rssi. If delta is a negative number, the BSSs that
2810 * belong to the specified band will be penalized by delta dB in relative
2811 * comparisons.
2812 */
2813struct cfg80211_sched_scan_request {
2814 u64 reqid;
2815 struct cfg80211_ssid *ssids;
2816 int n_ssids;
2817 u32 n_channels;
2818 const u8 *ie;
2819 size_t ie_len;
2820 u32 flags;
2821 struct cfg80211_match_set *match_sets;
2822 int n_match_sets;
2823 s32 min_rssi_thold;
2824 u32 delay;
2825 struct cfg80211_sched_scan_plan *scan_plans;
2826 int n_scan_plans;
2827
2828 u8 mac_addr[ETH_ALEN] __aligned(2);
2829 u8 mac_addr_mask[ETH_ALEN] __aligned(2);
2830
2831 bool relative_rssi_set;
2832 s8 relative_rssi;
2833 struct cfg80211_bss_select_adjust rssi_adjust;
2834
2835 /* internal */
2836 struct wiphy *wiphy;
2837 struct net_device *dev;
2838 unsigned long scan_start;
2839 bool report_results;
2840 struct rcu_head rcu_head;
2841 u32 owner_nlportid;
2842 bool nl_owner_dead;
2843 struct list_head list;
2844
2845 /* keep last */
2846 struct ieee80211_channel *channels[] __counted_by(n_channels);
2847};
2848
2849/**
2850 * enum cfg80211_signal_type - signal type
2851 *
2852 * @CFG80211_SIGNAL_TYPE_NONE: no signal strength information available
2853 * @CFG80211_SIGNAL_TYPE_MBM: signal strength in mBm (100*dBm)
2854 * @CFG80211_SIGNAL_TYPE_UNSPEC: signal strength, increasing from 0 through 100
2855 */
2856enum cfg80211_signal_type {
2857 CFG80211_SIGNAL_TYPE_NONE,
2858 CFG80211_SIGNAL_TYPE_MBM,
2859 CFG80211_SIGNAL_TYPE_UNSPEC,
2860};
2861
2862/**
2863 * struct cfg80211_inform_bss - BSS inform data
2864 * @chan: channel the frame was received on
2865 * @signal: signal strength value, according to the wiphy's
2866 * signal type
2867 * @boottime_ns: timestamp (CLOCK_BOOTTIME) when the information was
2868 * received; should match the time when the frame was actually
2869 * received by the device (not just by the host, in case it was
2870 * buffered on the device) and be accurate to about 10ms.
2871 * If the frame isn't buffered, just passing the return value of
2872 * ktime_get_boottime_ns() is likely appropriate.
2873 * @parent_tsf: the time at the start of reception of the first octet of the
2874 * timestamp field of the frame. The time is the TSF of the BSS specified
2875 * by %parent_bssid.
2876 * @parent_bssid: the BSS according to which %parent_tsf is set. This is set to
2877 * the BSS that requested the scan in which the beacon/probe was received.
2878 * @chains: bitmask for filled values in @chain_signal.
2879 * @chain_signal: per-chain signal strength of last received BSS in dBm.
2880 * @restrict_use: restrict usage, if not set, assume @use_for is
2881 * %NL80211_BSS_USE_FOR_NORMAL.
2882 * @use_for: bitmap of possible usage for this BSS, see
2883 * &enum nl80211_bss_use_for
2884 * @cannot_use_reasons: the reasons (bitmap) for not being able to connect,
2885 * if @restrict_use is set and @use_for is zero (empty); may be 0 for
2886 * unspecified reasons; see &enum nl80211_bss_cannot_use_reasons
2887 * @drv_data: Data to be passed through to @inform_bss
2888 */
2889struct cfg80211_inform_bss {
2890 struct ieee80211_channel *chan;
2891 s32 signal;
2892 u64 boottime_ns;
2893 u64 parent_tsf;
2894 u8 parent_bssid[ETH_ALEN] __aligned(2);
2895 u8 chains;
2896 s8 chain_signal[IEEE80211_MAX_CHAINS];
2897
2898 u8 restrict_use:1, use_for:7;
2899 u8 cannot_use_reasons;
2900
2901 void *drv_data;
2902};
2903
2904/**
2905 * struct cfg80211_bss_ies - BSS entry IE data
2906 * @tsf: TSF contained in the frame that carried these IEs
2907 * @rcu_head: internal use, for freeing
2908 * @len: length of the IEs
2909 * @from_beacon: these IEs are known to come from a beacon
2910 * @data: IE data
2911 */
2912struct cfg80211_bss_ies {
2913 u64 tsf;
2914 struct rcu_head rcu_head;
2915 int len;
2916 bool from_beacon;
2917 u8 data[];
2918};
2919
2920/**
2921 * struct cfg80211_bss - BSS description
2922 *
2923 * This structure describes a BSS (which may also be a mesh network)
2924 * for use in scan results and similar.
2925 *
2926 * @channel: channel this BSS is on
2927 * @bssid: BSSID of the BSS
2928 * @beacon_interval: the beacon interval as from the frame
2929 * @capability: the capability field in host byte order
2930 * @ies: the information elements (Note that there is no guarantee that these
2931 * are well-formed!); this is a pointer to either the beacon_ies or
2932 * proberesp_ies depending on whether Probe Response frame has been
2933 * received. It is always non-%NULL.
2934 * @beacon_ies: the information elements from the last Beacon frame
2935 * (implementation note: if @hidden_beacon_bss is set this struct doesn't
2936 * own the beacon_ies, but they're just pointers to the ones from the
2937 * @hidden_beacon_bss struct)
2938 * @proberesp_ies: the information elements from the last Probe Response frame
2939 * @proberesp_ecsa_stuck: ECSA element is stuck in the Probe Response frame,
2940 * cannot rely on it having valid data
2941 * @hidden_beacon_bss: in case this BSS struct represents a probe response from
2942 * a BSS that hides the SSID in its beacon, this points to the BSS struct
2943 * that holds the beacon data. @beacon_ies is still valid, of course, and
2944 * points to the same data as hidden_beacon_bss->beacon_ies in that case.
2945 * @transmitted_bss: pointer to the transmitted BSS, if this is a
2946 * non-transmitted one (multi-BSSID support)
2947 * @nontrans_list: list of non-transmitted BSS, if this is a transmitted one
2948 * (multi-BSSID support)
2949 * @signal: signal strength value (type depends on the wiphy's signal_type)
2950 * @chains: bitmask for filled values in @chain_signal.
2951 * @chain_signal: per-chain signal strength of last received BSS in dBm.
2952 * @bssid_index: index in the multiple BSS set
2953 * @max_bssid_indicator: max number of members in the BSS set
2954 * @use_for: bitmap of possible usage for this BSS, see
2955 * &enum nl80211_bss_use_for
2956 * @cannot_use_reasons: the reasons (bitmap) for not being able to connect,
2957 * if @restrict_use is set and @use_for is zero (empty); may be 0 for
2958 * unspecified reasons; see &enum nl80211_bss_cannot_use_reasons
2959 * @priv: private area for driver use, has at least wiphy->bss_priv_size bytes
2960 */
2961struct cfg80211_bss {
2962 struct ieee80211_channel *channel;
2963
2964 const struct cfg80211_bss_ies __rcu *ies;
2965 const struct cfg80211_bss_ies __rcu *beacon_ies;
2966 const struct cfg80211_bss_ies __rcu *proberesp_ies;
2967
2968 struct cfg80211_bss *hidden_beacon_bss;
2969 struct cfg80211_bss *transmitted_bss;
2970 struct list_head nontrans_list;
2971
2972 s32 signal;
2973
2974 u16 beacon_interval;
2975 u16 capability;
2976
2977 u8 bssid[ETH_ALEN];
2978 u8 chains;
2979 s8 chain_signal[IEEE80211_MAX_CHAINS];
2980
2981 u8 proberesp_ecsa_stuck:1;
2982
2983 u8 bssid_index;
2984 u8 max_bssid_indicator;
2985
2986 u8 use_for;
2987 u8 cannot_use_reasons;
2988
2989 u8 priv[] __aligned(sizeof(void *));
2990};
2991
2992/**
2993 * ieee80211_bss_get_elem - find element with given ID
2994 * @bss: the bss to search
2995 * @id: the element ID
2996 *
2997 * Note that the return value is an RCU-protected pointer, so
2998 * rcu_read_lock() must be held when calling this function.
2999 * Return: %NULL if not found.
3000 */
3001const struct element *ieee80211_bss_get_elem(struct cfg80211_bss *bss, u8 id);
3002
3003/**
3004 * ieee80211_bss_get_ie - find IE with given ID
3005 * @bss: the bss to search
3006 * @id: the element ID
3007 *
3008 * Note that the return value is an RCU-protected pointer, so
3009 * rcu_read_lock() must be held when calling this function.
3010 * Return: %NULL if not found.
3011 */
3012static inline const u8 *ieee80211_bss_get_ie(struct cfg80211_bss *bss, u8 id)
3013{
3014 return (const void *)ieee80211_bss_get_elem(bss, id);
3015}
3016
3017
3018/**
3019 * struct cfg80211_auth_request - Authentication request data
3020 *
3021 * This structure provides information needed to complete IEEE 802.11
3022 * authentication.
3023 *
3024 * @bss: The BSS to authenticate with, the callee must obtain a reference
3025 * to it if it needs to keep it.
3026 * @auth_type: Authentication type (algorithm)
3027 * @ie: Extra IEs to add to Authentication frame or %NULL
3028 * @ie_len: Length of ie buffer in octets
3029 * @key_len: length of WEP key for shared key authentication
3030 * @key_idx: index of WEP key for shared key authentication
3031 * @key: WEP key for shared key authentication
3032 * @auth_data: Fields and elements in Authentication frames. This contains
3033 * the authentication frame body (non-IE and IE data), excluding the
3034 * Authentication algorithm number, i.e., starting at the Authentication
3035 * transaction sequence number field.
3036 * @auth_data_len: Length of auth_data buffer in octets
3037 * @link_id: if >= 0, indicates authentication should be done as an MLD,
3038 * the interface address is included as the MLD address and the
3039 * necessary link (with the given link_id) will be created (and
3040 * given an MLD address) by the driver
3041 * @ap_mld_addr: AP MLD address in case of authentication request with
3042 * an AP MLD, valid iff @link_id >= 0
3043 */
3044struct cfg80211_auth_request {
3045 struct cfg80211_bss *bss;
3046 const u8 *ie;
3047 size_t ie_len;
3048 enum nl80211_auth_type auth_type;
3049 const u8 *key;
3050 u8 key_len;
3051 s8 key_idx;
3052 const u8 *auth_data;
3053 size_t auth_data_len;
3054 s8 link_id;
3055 const u8 *ap_mld_addr;
3056};
3057
3058/**
3059 * struct cfg80211_assoc_link - per-link information for MLO association
3060 * @bss: the BSS pointer, see also &struct cfg80211_assoc_request::bss;
3061 * if this is %NULL for a link, that link is not requested
3062 * @elems: extra elements for the per-STA profile for this link
3063 * @elems_len: length of the elements
3064 * @disabled: If set this link should be included during association etc. but it
3065 * should not be used until enabled by the AP MLD.
3066 * @error: per-link error code, must be <= 0. If there is an error, then the
3067 * operation as a whole must fail.
3068 */
3069struct cfg80211_assoc_link {
3070 struct cfg80211_bss *bss;
3071 const u8 *elems;
3072 size_t elems_len;
3073 bool disabled;
3074 int error;
3075};
3076
3077/**
3078 * enum cfg80211_assoc_req_flags - Over-ride default behaviour in association.
3079 *
3080 * @ASSOC_REQ_DISABLE_HT: Disable HT (802.11n)
3081 * @ASSOC_REQ_DISABLE_VHT: Disable VHT
3082 * @ASSOC_REQ_USE_RRM: Declare RRM capability in this association
3083 * @CONNECT_REQ_EXTERNAL_AUTH_SUPPORT: User space indicates external
3084 * authentication capability. Drivers can offload authentication to
3085 * userspace if this flag is set. Only applicable for cfg80211_connect()
3086 * request (connect callback).
3087 * @ASSOC_REQ_DISABLE_HE: Disable HE
3088 * @ASSOC_REQ_DISABLE_EHT: Disable EHT
3089 * @CONNECT_REQ_MLO_SUPPORT: Userspace indicates support for handling MLD links.
3090 * Drivers shall disable MLO features for the current association if this
3091 * flag is not set.
3092 * @ASSOC_REQ_SPP_AMSDU: SPP A-MSDUs will be used on this connection (if any)
3093 */
3094enum cfg80211_assoc_req_flags {
3095 ASSOC_REQ_DISABLE_HT = BIT(0),
3096 ASSOC_REQ_DISABLE_VHT = BIT(1),
3097 ASSOC_REQ_USE_RRM = BIT(2),
3098 CONNECT_REQ_EXTERNAL_AUTH_SUPPORT = BIT(3),
3099 ASSOC_REQ_DISABLE_HE = BIT(4),
3100 ASSOC_REQ_DISABLE_EHT = BIT(5),
3101 CONNECT_REQ_MLO_SUPPORT = BIT(6),
3102 ASSOC_REQ_SPP_AMSDU = BIT(7),
3103};
3104
3105/**
3106 * struct cfg80211_assoc_request - (Re)Association request data
3107 *
3108 * This structure provides information needed to complete IEEE 802.11
3109 * (re)association.
3110 * @bss: The BSS to associate with. If the call is successful the driver is
3111 * given a reference that it must give back to cfg80211_send_rx_assoc()
3112 * or to cfg80211_assoc_timeout(). To ensure proper refcounting, new
3113 * association requests while already associating must be rejected.
3114 * This also applies to the @links.bss parameter, which is used instead
3115 * of this one (it is %NULL) for MLO associations.
3116 * @ie: Extra IEs to add to (Re)Association Request frame or %NULL
3117 * @ie_len: Length of ie buffer in octets
3118 * @use_mfp: Use management frame protection (IEEE 802.11w) in this association
3119 * @crypto: crypto settings
3120 * @prev_bssid: previous BSSID, if not %NULL use reassociate frame. This is used
3121 * to indicate a request to reassociate within the ESS instead of a request
3122 * do the initial association with the ESS. When included, this is set to
3123 * the BSSID of the current association, i.e., to the value that is
3124 * included in the Current AP address field of the Reassociation Request
3125 * frame.
3126 * @flags: See &enum cfg80211_assoc_req_flags
3127 * @ht_capa: HT Capabilities over-rides. Values set in ht_capa_mask
3128 * will be used in ht_capa. Un-supported values will be ignored.
3129 * @ht_capa_mask: The bits of ht_capa which are to be used.
3130 * @vht_capa: VHT capability override
3131 * @vht_capa_mask: VHT capability mask indicating which fields to use
3132 * @fils_kek: FILS KEK for protecting (Re)Association Request/Response frame or
3133 * %NULL if FILS is not used.
3134 * @fils_kek_len: Length of fils_kek in octets
3135 * @fils_nonces: FILS nonces (part of AAD) for protecting (Re)Association
3136 * Request/Response frame or %NULL if FILS is not used. This field starts
3137 * with 16 octets of STA Nonce followed by 16 octets of AP Nonce.
3138 * @s1g_capa: S1G capability override
3139 * @s1g_capa_mask: S1G capability override mask
3140 * @links: per-link information for MLO connections
3141 * @link_id: >= 0 for MLO connections, where links are given, and indicates
3142 * the link on which the association request should be sent
3143 * @ap_mld_addr: AP MLD address in case of MLO association request,
3144 * valid iff @link_id >= 0
3145 */
3146struct cfg80211_assoc_request {
3147 struct cfg80211_bss *bss;
3148 const u8 *ie, *prev_bssid;
3149 size_t ie_len;
3150 struct cfg80211_crypto_settings crypto;
3151 bool use_mfp;
3152 u32 flags;
3153 struct ieee80211_ht_cap ht_capa;
3154 struct ieee80211_ht_cap ht_capa_mask;
3155 struct ieee80211_vht_cap vht_capa, vht_capa_mask;
3156 const u8 *fils_kek;
3157 size_t fils_kek_len;
3158 const u8 *fils_nonces;
3159 struct ieee80211_s1g_cap s1g_capa, s1g_capa_mask;
3160 struct cfg80211_assoc_link links[IEEE80211_MLD_MAX_NUM_LINKS];
3161 const u8 *ap_mld_addr;
3162 s8 link_id;
3163};
3164
3165/**
3166 * struct cfg80211_deauth_request - Deauthentication request data
3167 *
3168 * This structure provides information needed to complete IEEE 802.11
3169 * deauthentication.
3170 *
3171 * @bssid: the BSSID or AP MLD address to deauthenticate from
3172 * @ie: Extra IEs to add to Deauthentication frame or %NULL
3173 * @ie_len: Length of ie buffer in octets
3174 * @reason_code: The reason code for the deauthentication
3175 * @local_state_change: if set, change local state only and
3176 * do not set a deauth frame
3177 */
3178struct cfg80211_deauth_request {
3179 const u8 *bssid;
3180 const u8 *ie;
3181 size_t ie_len;
3182 u16 reason_code;
3183 bool local_state_change;
3184};
3185
3186/**
3187 * struct cfg80211_disassoc_request - Disassociation request data
3188 *
3189 * This structure provides information needed to complete IEEE 802.11
3190 * disassociation.
3191 *
3192 * @ap_addr: the BSSID or AP MLD address to disassociate from
3193 * @ie: Extra IEs to add to Disassociation frame or %NULL
3194 * @ie_len: Length of ie buffer in octets
3195 * @reason_code: The reason code for the disassociation
3196 * @local_state_change: This is a request for a local state only, i.e., no
3197 * Disassociation frame is to be transmitted.
3198 */
3199struct cfg80211_disassoc_request {
3200 const u8 *ap_addr;
3201 const u8 *ie;
3202 size_t ie_len;
3203 u16 reason_code;
3204 bool local_state_change;
3205};
3206
3207/**
3208 * struct cfg80211_ibss_params - IBSS parameters
3209 *
3210 * This structure defines the IBSS parameters for the join_ibss()
3211 * method.
3212 *
3213 * @ssid: The SSID, will always be non-null.
3214 * @ssid_len: The length of the SSID, will always be non-zero.
3215 * @bssid: Fixed BSSID requested, maybe be %NULL, if set do not
3216 * search for IBSSs with a different BSSID.
3217 * @chandef: defines the channel to use if no other IBSS to join can be found
3218 * @channel_fixed: The channel should be fixed -- do not search for
3219 * IBSSs to join on other channels.
3220 * @ie: information element(s) to include in the beacon
3221 * @ie_len: length of that
3222 * @beacon_interval: beacon interval to use
3223 * @privacy: this is a protected network, keys will be configured
3224 * after joining
3225 * @control_port: whether user space controls IEEE 802.1X port, i.e.,
3226 * sets/clears %NL80211_STA_FLAG_AUTHORIZED. If true, the driver is
3227 * required to assume that the port is unauthorized until authorized by
3228 * user space. Otherwise, port is marked authorized by default.
3229 * @control_port_over_nl80211: TRUE if userspace expects to exchange control
3230 * port frames over NL80211 instead of the network interface.
3231 * @userspace_handles_dfs: whether user space controls DFS operation, i.e.
3232 * changes the channel when a radar is detected. This is required
3233 * to operate on DFS channels.
3234 * @basic_rates: bitmap of basic rates to use when creating the IBSS
3235 * @mcast_rate: per-band multicast rate index + 1 (0: disabled)
3236 * @ht_capa: HT Capabilities over-rides. Values set in ht_capa_mask
3237 * will be used in ht_capa. Un-supported values will be ignored.
3238 * @ht_capa_mask: The bits of ht_capa which are to be used.
3239 * @wep_keys: static WEP keys, if not NULL points to an array of
3240 * CFG80211_MAX_WEP_KEYS WEP keys
3241 * @wep_tx_key: key index (0..3) of the default TX static WEP key
3242 */
3243struct cfg80211_ibss_params {
3244 const u8 *ssid;
3245 const u8 *bssid;
3246 struct cfg80211_chan_def chandef;
3247 const u8 *ie;
3248 u8 ssid_len, ie_len;
3249 u16 beacon_interval;
3250 u32 basic_rates;
3251 bool channel_fixed;
3252 bool privacy;
3253 bool control_port;
3254 bool control_port_over_nl80211;
3255 bool userspace_handles_dfs;
3256 int mcast_rate[NUM_NL80211_BANDS];
3257 struct ieee80211_ht_cap ht_capa;
3258 struct ieee80211_ht_cap ht_capa_mask;
3259 struct key_params *wep_keys;
3260 int wep_tx_key;
3261};
3262
3263/**
3264 * struct cfg80211_bss_selection - connection parameters for BSS selection.
3265 *
3266 * @behaviour: requested BSS selection behaviour.
3267 * @param: parameters for requestion behaviour.
3268 * @param.band_pref: preferred band for %NL80211_BSS_SELECT_ATTR_BAND_PREF.
3269 * @param.adjust: parameters for %NL80211_BSS_SELECT_ATTR_RSSI_ADJUST.
3270 */
3271struct cfg80211_bss_selection {
3272 enum nl80211_bss_select_attr behaviour;
3273 union {
3274 enum nl80211_band band_pref;
3275 struct cfg80211_bss_select_adjust adjust;
3276 } param;
3277};
3278
3279/**
3280 * struct cfg80211_connect_params - Connection parameters
3281 *
3282 * This structure provides information needed to complete IEEE 802.11
3283 * authentication and association.
3284 *
3285 * @channel: The channel to use or %NULL if not specified (auto-select based
3286 * on scan results)
3287 * @channel_hint: The channel of the recommended BSS for initial connection or
3288 * %NULL if not specified
3289 * @bssid: The AP BSSID or %NULL if not specified (auto-select based on scan
3290 * results)
3291 * @bssid_hint: The recommended AP BSSID for initial connection to the BSS or
3292 * %NULL if not specified. Unlike the @bssid parameter, the driver is
3293 * allowed to ignore this @bssid_hint if it has knowledge of a better BSS
3294 * to use.
3295 * @ssid: SSID
3296 * @ssid_len: Length of ssid in octets
3297 * @auth_type: Authentication type (algorithm)
3298 * @ie: IEs for association request
3299 * @ie_len: Length of assoc_ie in octets
3300 * @privacy: indicates whether privacy-enabled APs should be used
3301 * @mfp: indicate whether management frame protection is used
3302 * @crypto: crypto settings
3303 * @key_len: length of WEP key for shared key authentication
3304 * @key_idx: index of WEP key for shared key authentication
3305 * @key: WEP key for shared key authentication
3306 * @flags: See &enum cfg80211_assoc_req_flags
3307 * @bg_scan_period: Background scan period in seconds
3308 * or -1 to indicate that default value is to be used.
3309 * @ht_capa: HT Capabilities over-rides. Values set in ht_capa_mask
3310 * will be used in ht_capa. Un-supported values will be ignored.
3311 * @ht_capa_mask: The bits of ht_capa which are to be used.
3312 * @vht_capa: VHT Capability overrides
3313 * @vht_capa_mask: The bits of vht_capa which are to be used.
3314 * @pbss: if set, connect to a PCP instead of AP. Valid for DMG
3315 * networks.
3316 * @bss_select: criteria to be used for BSS selection.
3317 * @prev_bssid: previous BSSID, if not %NULL use reassociate frame. This is used
3318 * to indicate a request to reassociate within the ESS instead of a request
3319 * do the initial association with the ESS. When included, this is set to
3320 * the BSSID of the current association, i.e., to the value that is
3321 * included in the Current AP address field of the Reassociation Request
3322 * frame.
3323 * @fils_erp_username: EAP re-authentication protocol (ERP) username part of the
3324 * NAI or %NULL if not specified. This is used to construct FILS wrapped
3325 * data IE.
3326 * @fils_erp_username_len: Length of @fils_erp_username in octets.
3327 * @fils_erp_realm: EAP re-authentication protocol (ERP) realm part of NAI or
3328 * %NULL if not specified. This specifies the domain name of ER server and
3329 * is used to construct FILS wrapped data IE.
3330 * @fils_erp_realm_len: Length of @fils_erp_realm in octets.
3331 * @fils_erp_next_seq_num: The next sequence number to use in the FILS ERP
3332 * messages. This is also used to construct FILS wrapped data IE.
3333 * @fils_erp_rrk: ERP re-authentication Root Key (rRK) used to derive additional
3334 * keys in FILS or %NULL if not specified.
3335 * @fils_erp_rrk_len: Length of @fils_erp_rrk in octets.
3336 * @want_1x: indicates user-space supports and wants to use 802.1X driver
3337 * offload of 4-way handshake.
3338 * @edmg: define the EDMG channels.
3339 * This may specify multiple channels and bonding options for the driver
3340 * to choose from, based on BSS configuration.
3341 */
3342struct cfg80211_connect_params {
3343 struct ieee80211_channel *channel;
3344 struct ieee80211_channel *channel_hint;
3345 const u8 *bssid;
3346 const u8 *bssid_hint;
3347 const u8 *ssid;
3348 size_t ssid_len;
3349 enum nl80211_auth_type auth_type;
3350 const u8 *ie;
3351 size_t ie_len;
3352 bool privacy;
3353 enum nl80211_mfp mfp;
3354 struct cfg80211_crypto_settings crypto;
3355 const u8 *key;
3356 u8 key_len, key_idx;
3357 u32 flags;
3358 int bg_scan_period;
3359 struct ieee80211_ht_cap ht_capa;
3360 struct ieee80211_ht_cap ht_capa_mask;
3361 struct ieee80211_vht_cap vht_capa;
3362 struct ieee80211_vht_cap vht_capa_mask;
3363 bool pbss;
3364 struct cfg80211_bss_selection bss_select;
3365 const u8 *prev_bssid;
3366 const u8 *fils_erp_username;
3367 size_t fils_erp_username_len;
3368 const u8 *fils_erp_realm;
3369 size_t fils_erp_realm_len;
3370 u16 fils_erp_next_seq_num;
3371 const u8 *fils_erp_rrk;
3372 size_t fils_erp_rrk_len;
3373 bool want_1x;
3374 struct ieee80211_edmg edmg;
3375};
3376
3377/**
3378 * enum cfg80211_connect_params_changed - Connection parameters being updated
3379 *
3380 * This enum provides information of all connect parameters that
3381 * have to be updated as part of update_connect_params() call.
3382 *
3383 * @UPDATE_ASSOC_IES: Indicates whether association request IEs are updated
3384 * @UPDATE_FILS_ERP_INFO: Indicates that FILS connection parameters (realm,
3385 * username, erp sequence number and rrk) are updated
3386 * @UPDATE_AUTH_TYPE: Indicates that authentication type is updated
3387 */
3388enum cfg80211_connect_params_changed {
3389 UPDATE_ASSOC_IES = BIT(0),
3390 UPDATE_FILS_ERP_INFO = BIT(1),
3391 UPDATE_AUTH_TYPE = BIT(2),
3392};
3393
3394/**
3395 * enum wiphy_params_flags - set_wiphy_params bitfield values
3396 * @WIPHY_PARAM_RETRY_SHORT: wiphy->retry_short has changed
3397 * @WIPHY_PARAM_RETRY_LONG: wiphy->retry_long has changed
3398 * @WIPHY_PARAM_FRAG_THRESHOLD: wiphy->frag_threshold has changed
3399 * @WIPHY_PARAM_RTS_THRESHOLD: wiphy->rts_threshold has changed
3400 * @WIPHY_PARAM_COVERAGE_CLASS: coverage class changed
3401 * @WIPHY_PARAM_DYN_ACK: dynack has been enabled
3402 * @WIPHY_PARAM_TXQ_LIMIT: TXQ packet limit has been changed
3403 * @WIPHY_PARAM_TXQ_MEMORY_LIMIT: TXQ memory limit has been changed
3404 * @WIPHY_PARAM_TXQ_QUANTUM: TXQ scheduler quantum
3405 */
3406enum wiphy_params_flags {
3407 WIPHY_PARAM_RETRY_SHORT = BIT(0),
3408 WIPHY_PARAM_RETRY_LONG = BIT(1),
3409 WIPHY_PARAM_FRAG_THRESHOLD = BIT(2),
3410 WIPHY_PARAM_RTS_THRESHOLD = BIT(3),
3411 WIPHY_PARAM_COVERAGE_CLASS = BIT(4),
3412 WIPHY_PARAM_DYN_ACK = BIT(5),
3413 WIPHY_PARAM_TXQ_LIMIT = BIT(6),
3414 WIPHY_PARAM_TXQ_MEMORY_LIMIT = BIT(7),
3415 WIPHY_PARAM_TXQ_QUANTUM = BIT(8),
3416};
3417
3418#define IEEE80211_DEFAULT_AIRTIME_WEIGHT 256
3419
3420/* The per TXQ device queue limit in airtime */
3421#define IEEE80211_DEFAULT_AQL_TXQ_LIMIT_L 5000
3422#define IEEE80211_DEFAULT_AQL_TXQ_LIMIT_H 12000
3423
3424/* The per interface airtime threshold to switch to lower queue limit */
3425#define IEEE80211_AQL_THRESHOLD 24000
3426
3427/**
3428 * struct cfg80211_pmksa - PMK Security Association
3429 *
3430 * This structure is passed to the set/del_pmksa() method for PMKSA
3431 * caching.
3432 *
3433 * @bssid: The AP's BSSID (may be %NULL).
3434 * @pmkid: The identifier to refer a PMKSA.
3435 * @pmk: The PMK for the PMKSA identified by @pmkid. This is used for key
3436 * derivation by a FILS STA. Otherwise, %NULL.
3437 * @pmk_len: Length of the @pmk. The length of @pmk can differ depending on
3438 * the hash algorithm used to generate this.
3439 * @ssid: SSID to specify the ESS within which a PMKSA is valid when using FILS
3440 * cache identifier (may be %NULL).
3441 * @ssid_len: Length of the @ssid in octets.
3442 * @cache_id: 2-octet cache identifier advertized by a FILS AP identifying the
3443 * scope of PMKSA. This is valid only if @ssid_len is non-zero (may be
3444 * %NULL).
3445 * @pmk_lifetime: Maximum lifetime for PMKSA in seconds
3446 * (dot11RSNAConfigPMKLifetime) or 0 if not specified.
3447 * The configured PMKSA must not be used for PMKSA caching after
3448 * expiration and any keys derived from this PMK become invalid on
3449 * expiration, i.e., the current association must be dropped if the PMK
3450 * used for it expires.
3451 * @pmk_reauth_threshold: Threshold time for reauthentication (percentage of
3452 * PMK lifetime, dot11RSNAConfigPMKReauthThreshold) or 0 if not specified.
3453 * Drivers are expected to trigger a full authentication instead of using
3454 * this PMKSA for caching when reassociating to a new BSS after this
3455 * threshold to generate a new PMK before the current one expires.
3456 */
3457struct cfg80211_pmksa {
3458 const u8 *bssid;
3459 const u8 *pmkid;
3460 const u8 *pmk;
3461 size_t pmk_len;
3462 const u8 *ssid;
3463 size_t ssid_len;
3464 const u8 *cache_id;
3465 u32 pmk_lifetime;
3466 u8 pmk_reauth_threshold;
3467};
3468
3469/**
3470 * struct cfg80211_pkt_pattern - packet pattern
3471 * @mask: bitmask where to match pattern and where to ignore bytes,
3472 * one bit per byte, in same format as nl80211
3473 * @pattern: bytes to match where bitmask is 1
3474 * @pattern_len: length of pattern (in bytes)
3475 * @pkt_offset: packet offset (in bytes)
3476 *
3477 * Internal note: @mask and @pattern are allocated in one chunk of
3478 * memory, free @mask only!
3479 */
3480struct cfg80211_pkt_pattern {
3481 const u8 *mask, *pattern;
3482 int pattern_len;
3483 int pkt_offset;
3484};
3485
3486/**
3487 * struct cfg80211_wowlan_tcp - TCP connection parameters
3488 *
3489 * @sock: (internal) socket for source port allocation
3490 * @src: source IP address
3491 * @dst: destination IP address
3492 * @dst_mac: destination MAC address
3493 * @src_port: source port
3494 * @dst_port: destination port
3495 * @payload_len: data payload length
3496 * @payload: data payload buffer
3497 * @payload_seq: payload sequence stamping configuration
3498 * @data_interval: interval at which to send data packets
3499 * @wake_len: wakeup payload match length
3500 * @wake_data: wakeup payload match data
3501 * @wake_mask: wakeup payload match mask
3502 * @tokens_size: length of the tokens buffer
3503 * @payload_tok: payload token usage configuration
3504 */
3505struct cfg80211_wowlan_tcp {
3506 struct socket *sock;
3507 __be32 src, dst;
3508 u16 src_port, dst_port;
3509 u8 dst_mac[ETH_ALEN];
3510 int payload_len;
3511 const u8 *payload;
3512 struct nl80211_wowlan_tcp_data_seq payload_seq;
3513 u32 data_interval;
3514 u32 wake_len;
3515 const u8 *wake_data, *wake_mask;
3516 u32 tokens_size;
3517 /* must be last, variable member */
3518 struct nl80211_wowlan_tcp_data_token payload_tok;
3519};
3520
3521/**
3522 * struct cfg80211_wowlan - Wake on Wireless-LAN support info
3523 *
3524 * This structure defines the enabled WoWLAN triggers for the device.
3525 * @any: wake up on any activity -- special trigger if device continues
3526 * operating as normal during suspend
3527 * @disconnect: wake up if getting disconnected
3528 * @magic_pkt: wake up on receiving magic packet
3529 * @patterns: wake up on receiving packet matching a pattern
3530 * @n_patterns: number of patterns
3531 * @gtk_rekey_failure: wake up on GTK rekey failure
3532 * @eap_identity_req: wake up on EAP identity request packet
3533 * @four_way_handshake: wake up on 4-way handshake
3534 * @rfkill_release: wake up when rfkill is released
3535 * @tcp: TCP connection establishment/wakeup parameters, see nl80211.h.
3536 * NULL if not configured.
3537 * @nd_config: configuration for the scan to be used for net detect wake.
3538 */
3539struct cfg80211_wowlan {
3540 bool any, disconnect, magic_pkt, gtk_rekey_failure,
3541 eap_identity_req, four_way_handshake,
3542 rfkill_release;
3543 struct cfg80211_pkt_pattern *patterns;
3544 struct cfg80211_wowlan_tcp *tcp;
3545 int n_patterns;
3546 struct cfg80211_sched_scan_request *nd_config;
3547};
3548
3549/**
3550 * struct cfg80211_coalesce_rules - Coalesce rule parameters
3551 *
3552 * This structure defines coalesce rule for the device.
3553 * @delay: maximum coalescing delay in msecs.
3554 * @condition: condition for packet coalescence.
3555 * see &enum nl80211_coalesce_condition.
3556 * @patterns: array of packet patterns
3557 * @n_patterns: number of patterns
3558 */
3559struct cfg80211_coalesce_rules {
3560 int delay;
3561 enum nl80211_coalesce_condition condition;
3562 struct cfg80211_pkt_pattern *patterns;
3563 int n_patterns;
3564};
3565
3566/**
3567 * struct cfg80211_coalesce - Packet coalescing settings
3568 *
3569 * This structure defines coalescing settings.
3570 * @rules: array of coalesce rules
3571 * @n_rules: number of rules
3572 */
3573struct cfg80211_coalesce {
3574 int n_rules;
3575 struct cfg80211_coalesce_rules rules[] __counted_by(n_rules);
3576};
3577
3578/**
3579 * struct cfg80211_wowlan_nd_match - information about the match
3580 *
3581 * @ssid: SSID of the match that triggered the wake up
3582 * @n_channels: Number of channels where the match occurred. This
3583 * value may be zero if the driver can't report the channels.
3584 * @channels: center frequencies of the channels where a match
3585 * occurred (in MHz)
3586 */
3587struct cfg80211_wowlan_nd_match {
3588 struct cfg80211_ssid ssid;
3589 int n_channels;
3590 u32 channels[] __counted_by(n_channels);
3591};
3592
3593/**
3594 * struct cfg80211_wowlan_nd_info - net detect wake up information
3595 *
3596 * @n_matches: Number of match information instances provided in
3597 * @matches. This value may be zero if the driver can't provide
3598 * match information.
3599 * @matches: Array of pointers to matches containing information about
3600 * the matches that triggered the wake up.
3601 */
3602struct cfg80211_wowlan_nd_info {
3603 int n_matches;
3604 struct cfg80211_wowlan_nd_match *matches[] __counted_by(n_matches);
3605};
3606
3607/**
3608 * struct cfg80211_wowlan_wakeup - wakeup report
3609 * @disconnect: woke up by getting disconnected
3610 * @magic_pkt: woke up by receiving magic packet
3611 * @gtk_rekey_failure: woke up by GTK rekey failure
3612 * @eap_identity_req: woke up by EAP identity request packet
3613 * @four_way_handshake: woke up by 4-way handshake
3614 * @rfkill_release: woke up by rfkill being released
3615 * @pattern_idx: pattern that caused wakeup, -1 if not due to pattern
3616 * @packet_present_len: copied wakeup packet data
3617 * @packet_len: original wakeup packet length
3618 * @packet: The packet causing the wakeup, if any.
3619 * @packet_80211: For pattern match, magic packet and other data
3620 * frame triggers an 802.3 frame should be reported, for
3621 * disconnect due to deauth 802.11 frame. This indicates which
3622 * it is.
3623 * @tcp_match: TCP wakeup packet received
3624 * @tcp_connlost: TCP connection lost or failed to establish
3625 * @tcp_nomoretokens: TCP data ran out of tokens
3626 * @net_detect: if not %NULL, woke up because of net detect
3627 * @unprot_deauth_disassoc: woke up due to unprotected deauth or
3628 * disassoc frame (in MFP).
3629 */
3630struct cfg80211_wowlan_wakeup {
3631 bool disconnect, magic_pkt, gtk_rekey_failure,
3632 eap_identity_req, four_way_handshake,
3633 rfkill_release, packet_80211,
3634 tcp_match, tcp_connlost, tcp_nomoretokens,
3635 unprot_deauth_disassoc;
3636 s32 pattern_idx;
3637 u32 packet_present_len, packet_len;
3638 const void *packet;
3639 struct cfg80211_wowlan_nd_info *net_detect;
3640};
3641
3642/**
3643 * struct cfg80211_gtk_rekey_data - rekey data
3644 * @kek: key encryption key (@kek_len bytes)
3645 * @kck: key confirmation key (@kck_len bytes)
3646 * @replay_ctr: replay counter (NL80211_REPLAY_CTR_LEN bytes)
3647 * @kek_len: length of kek
3648 * @kck_len: length of kck
3649 * @akm: akm (oui, id)
3650 */
3651struct cfg80211_gtk_rekey_data {
3652 const u8 *kek, *kck, *replay_ctr;
3653 u32 akm;
3654 u8 kek_len, kck_len;
3655};
3656
3657/**
3658 * struct cfg80211_update_ft_ies_params - FT IE Information
3659 *
3660 * This structure provides information needed to update the fast transition IE
3661 *
3662 * @md: The Mobility Domain ID, 2 Octet value
3663 * @ie: Fast Transition IEs
3664 * @ie_len: Length of ft_ie in octets
3665 */
3666struct cfg80211_update_ft_ies_params {
3667 u16 md;
3668 const u8 *ie;
3669 size_t ie_len;
3670};
3671
3672/**
3673 * struct cfg80211_mgmt_tx_params - mgmt tx parameters
3674 *
3675 * This structure provides information needed to transmit a mgmt frame
3676 *
3677 * @chan: channel to use
3678 * @offchan: indicates whether off channel operation is required
3679 * @wait: duration for ROC
3680 * @buf: buffer to transmit
3681 * @len: buffer length
3682 * @no_cck: don't use cck rates for this frame
3683 * @dont_wait_for_ack: tells the low level not to wait for an ack
3684 * @n_csa_offsets: length of csa_offsets array
3685 * @csa_offsets: array of all the csa offsets in the frame
3686 * @link_id: for MLO, the link ID to transmit on, -1 if not given; note
3687 * that the link ID isn't validated (much), it's in range but the
3688 * link might not exist (or be used by the receiver STA)
3689 */
3690struct cfg80211_mgmt_tx_params {
3691 struct ieee80211_channel *chan;
3692 bool offchan;
3693 unsigned int wait;
3694 const u8 *buf;
3695 size_t len;
3696 bool no_cck;
3697 bool dont_wait_for_ack;
3698 int n_csa_offsets;
3699 const u16 *csa_offsets;
3700 int link_id;
3701};
3702
3703/**
3704 * struct cfg80211_dscp_exception - DSCP exception
3705 *
3706 * @dscp: DSCP value that does not adhere to the user priority range definition
3707 * @up: user priority value to which the corresponding DSCP value belongs
3708 */
3709struct cfg80211_dscp_exception {
3710 u8 dscp;
3711 u8 up;
3712};
3713
3714/**
3715 * struct cfg80211_dscp_range - DSCP range definition for user priority
3716 *
3717 * @low: lowest DSCP value of this user priority range, inclusive
3718 * @high: highest DSCP value of this user priority range, inclusive
3719 */
3720struct cfg80211_dscp_range {
3721 u8 low;
3722 u8 high;
3723};
3724
3725/* QoS Map Set element length defined in IEEE Std 802.11-2012, 8.4.2.97 */
3726#define IEEE80211_QOS_MAP_MAX_EX 21
3727#define IEEE80211_QOS_MAP_LEN_MIN 16
3728#define IEEE80211_QOS_MAP_LEN_MAX \
3729 (IEEE80211_QOS_MAP_LEN_MIN + 2 * IEEE80211_QOS_MAP_MAX_EX)
3730
3731/**
3732 * struct cfg80211_qos_map - QoS Map Information
3733 *
3734 * This struct defines the Interworking QoS map setting for DSCP values
3735 *
3736 * @num_des: number of DSCP exceptions (0..21)
3737 * @dscp_exception: optionally up to maximum of 21 DSCP exceptions from
3738 * the user priority DSCP range definition
3739 * @up: DSCP range definition for a particular user priority
3740 */
3741struct cfg80211_qos_map {
3742 u8 num_des;
3743 struct cfg80211_dscp_exception dscp_exception[IEEE80211_QOS_MAP_MAX_EX];
3744 struct cfg80211_dscp_range up[8];
3745};
3746
3747/**
3748 * struct cfg80211_nan_conf - NAN configuration
3749 *
3750 * This struct defines NAN configuration parameters
3751 *
3752 * @master_pref: master preference (1 - 255)
3753 * @bands: operating bands, a bitmap of &enum nl80211_band values.
3754 * For instance, for NL80211_BAND_2GHZ, bit 0 would be set
3755 * (i.e. BIT(NL80211_BAND_2GHZ)).
3756 */
3757struct cfg80211_nan_conf {
3758 u8 master_pref;
3759 u8 bands;
3760};
3761
3762/**
3763 * enum cfg80211_nan_conf_changes - indicates changed fields in NAN
3764 * configuration
3765 *
3766 * @CFG80211_NAN_CONF_CHANGED_PREF: master preference
3767 * @CFG80211_NAN_CONF_CHANGED_BANDS: operating bands
3768 */
3769enum cfg80211_nan_conf_changes {
3770 CFG80211_NAN_CONF_CHANGED_PREF = BIT(0),
3771 CFG80211_NAN_CONF_CHANGED_BANDS = BIT(1),
3772};
3773
3774/**
3775 * struct cfg80211_nan_func_filter - a NAN function Rx / Tx filter
3776 *
3777 * @filter: the content of the filter
3778 * @len: the length of the filter
3779 */
3780struct cfg80211_nan_func_filter {
3781 const u8 *filter;
3782 u8 len;
3783};
3784
3785/**
3786 * struct cfg80211_nan_func - a NAN function
3787 *
3788 * @type: &enum nl80211_nan_function_type
3789 * @service_id: the service ID of the function
3790 * @publish_type: &nl80211_nan_publish_type
3791 * @close_range: if true, the range should be limited. Threshold is
3792 * implementation specific.
3793 * @publish_bcast: if true, the solicited publish should be broadcasted
3794 * @subscribe_active: if true, the subscribe is active
3795 * @followup_id: the instance ID for follow up
3796 * @followup_reqid: the requester instance ID for follow up
3797 * @followup_dest: MAC address of the recipient of the follow up
3798 * @ttl: time to live counter in DW.
3799 * @serv_spec_info: Service Specific Info
3800 * @serv_spec_info_len: Service Specific Info length
3801 * @srf_include: if true, SRF is inclusive
3802 * @srf_bf: Bloom Filter
3803 * @srf_bf_len: Bloom Filter length
3804 * @srf_bf_idx: Bloom Filter index
3805 * @srf_macs: SRF MAC addresses
3806 * @srf_num_macs: number of MAC addresses in SRF
3807 * @rx_filters: rx filters that are matched with corresponding peer's tx_filter
3808 * @tx_filters: filters that should be transmitted in the SDF.
3809 * @num_rx_filters: length of &rx_filters.
3810 * @num_tx_filters: length of &tx_filters.
3811 * @instance_id: driver allocated id of the function.
3812 * @cookie: unique NAN function identifier.
3813 */
3814struct cfg80211_nan_func {
3815 enum nl80211_nan_function_type type;
3816 u8 service_id[NL80211_NAN_FUNC_SERVICE_ID_LEN];
3817 u8 publish_type;
3818 bool close_range;
3819 bool publish_bcast;
3820 bool subscribe_active;
3821 u8 followup_id;
3822 u8 followup_reqid;
3823 struct mac_address followup_dest;
3824 u32 ttl;
3825 const u8 *serv_spec_info;
3826 u8 serv_spec_info_len;
3827 bool srf_include;
3828 const u8 *srf_bf;
3829 u8 srf_bf_len;
3830 u8 srf_bf_idx;
3831 struct mac_address *srf_macs;
3832 int srf_num_macs;
3833 struct cfg80211_nan_func_filter *rx_filters;
3834 struct cfg80211_nan_func_filter *tx_filters;
3835 u8 num_tx_filters;
3836 u8 num_rx_filters;
3837 u8 instance_id;
3838 u64 cookie;
3839};
3840
3841/**
3842 * struct cfg80211_pmk_conf - PMK configuration
3843 *
3844 * @aa: authenticator address
3845 * @pmk_len: PMK length in bytes.
3846 * @pmk: the PMK material
3847 * @pmk_r0_name: PMK-R0 Name. NULL if not applicable (i.e., the PMK
3848 * is not PMK-R0). When pmk_r0_name is not NULL, the pmk field
3849 * holds PMK-R0.
3850 */
3851struct cfg80211_pmk_conf {
3852 const u8 *aa;
3853 u8 pmk_len;
3854 const u8 *pmk;
3855 const u8 *pmk_r0_name;
3856};
3857
3858/**
3859 * struct cfg80211_external_auth_params - Trigger External authentication.
3860 *
3861 * Commonly used across the external auth request and event interfaces.
3862 *
3863 * @action: action type / trigger for external authentication. Only significant
3864 * for the authentication request event interface (driver to user space).
3865 * @bssid: BSSID of the peer with which the authentication has
3866 * to happen. Used by both the authentication request event and
3867 * authentication response command interface.
3868 * @ssid: SSID of the AP. Used by both the authentication request event and
3869 * authentication response command interface.
3870 * @key_mgmt_suite: AKM suite of the respective authentication. Used by the
3871 * authentication request event interface.
3872 * @status: status code, %WLAN_STATUS_SUCCESS for successful authentication,
3873 * use %WLAN_STATUS_UNSPECIFIED_FAILURE if user space cannot give you
3874 * the real status code for failures. Used only for the authentication
3875 * response command interface (user space to driver).
3876 * @pmkid: The identifier to refer a PMKSA.
3877 * @mld_addr: MLD address of the peer. Used by the authentication request event
3878 * interface. Driver indicates this to enable MLO during the authentication
3879 * offload to user space. Driver shall look at %NL80211_ATTR_MLO_SUPPORT
3880 * flag capability in NL80211_CMD_CONNECT to know whether the user space
3881 * supports enabling MLO during the authentication offload.
3882 * User space should use the address of the interface (on which the
3883 * authentication request event reported) as self MLD address. User space
3884 * and driver should use MLD addresses in RA, TA and BSSID fields of
3885 * authentication frames sent or received via cfg80211. The driver
3886 * translates the MLD addresses to/from link addresses based on the link
3887 * chosen for the authentication.
3888 */
3889struct cfg80211_external_auth_params {
3890 enum nl80211_external_auth_action action;
3891 u8 bssid[ETH_ALEN] __aligned(2);
3892 struct cfg80211_ssid ssid;
3893 unsigned int key_mgmt_suite;
3894 u16 status;
3895 const u8 *pmkid;
3896 u8 mld_addr[ETH_ALEN] __aligned(2);
3897};
3898
3899/**
3900 * struct cfg80211_ftm_responder_stats - FTM responder statistics
3901 *
3902 * @filled: bitflag of flags using the bits of &enum nl80211_ftm_stats to
3903 * indicate the relevant values in this struct for them
3904 * @success_num: number of FTM sessions in which all frames were successfully
3905 * answered
3906 * @partial_num: number of FTM sessions in which part of frames were
3907 * successfully answered
3908 * @failed_num: number of failed FTM sessions
3909 * @asap_num: number of ASAP FTM sessions
3910 * @non_asap_num: number of non-ASAP FTM sessions
3911 * @total_duration_ms: total sessions durations - gives an indication
3912 * of how much time the responder was busy
3913 * @unknown_triggers_num: number of unknown FTM triggers - triggers from
3914 * initiators that didn't finish successfully the negotiation phase with
3915 * the responder
3916 * @reschedule_requests_num: number of FTM reschedule requests - initiator asks
3917 * for a new scheduling although it already has scheduled FTM slot
3918 * @out_of_window_triggers_num: total FTM triggers out of scheduled window
3919 */
3920struct cfg80211_ftm_responder_stats {
3921 u32 filled;
3922 u32 success_num;
3923 u32 partial_num;
3924 u32 failed_num;
3925 u32 asap_num;
3926 u32 non_asap_num;
3927 u64 total_duration_ms;
3928 u32 unknown_triggers_num;
3929 u32 reschedule_requests_num;
3930 u32 out_of_window_triggers_num;
3931};
3932
3933/**
3934 * struct cfg80211_pmsr_ftm_result - FTM result
3935 * @failure_reason: if this measurement failed (PMSR status is
3936 * %NL80211_PMSR_STATUS_FAILURE), this gives a more precise
3937 * reason than just "failure"
3938 * @burst_index: if reporting partial results, this is the index
3939 * in [0 .. num_bursts-1] of the burst that's being reported
3940 * @num_ftmr_attempts: number of FTM request frames transmitted
3941 * @num_ftmr_successes: number of FTM request frames acked
3942 * @busy_retry_time: if failure_reason is %NL80211_PMSR_FTM_FAILURE_PEER_BUSY,
3943 * fill this to indicate in how many seconds a retry is deemed possible
3944 * by the responder
3945 * @num_bursts_exp: actual number of bursts exponent negotiated
3946 * @burst_duration: actual burst duration negotiated
3947 * @ftms_per_burst: actual FTMs per burst negotiated
3948 * @lci_len: length of LCI information (if present)
3949 * @civicloc_len: length of civic location information (if present)
3950 * @lci: LCI data (may be %NULL)
3951 * @civicloc: civic location data (may be %NULL)
3952 * @rssi_avg: average RSSI over FTM action frames reported
3953 * @rssi_spread: spread of the RSSI over FTM action frames reported
3954 * @tx_rate: bitrate for transmitted FTM action frame response
3955 * @rx_rate: bitrate of received FTM action frame
3956 * @rtt_avg: average of RTTs measured (must have either this or @dist_avg)
3957 * @rtt_variance: variance of RTTs measured (note that standard deviation is
3958 * the square root of the variance)
3959 * @rtt_spread: spread of the RTTs measured
3960 * @dist_avg: average of distances (mm) measured
3961 * (must have either this or @rtt_avg)
3962 * @dist_variance: variance of distances measured (see also @rtt_variance)
3963 * @dist_spread: spread of distances measured (see also @rtt_spread)
3964 * @num_ftmr_attempts_valid: @num_ftmr_attempts is valid
3965 * @num_ftmr_successes_valid: @num_ftmr_successes is valid
3966 * @rssi_avg_valid: @rssi_avg is valid
3967 * @rssi_spread_valid: @rssi_spread is valid
3968 * @tx_rate_valid: @tx_rate is valid
3969 * @rx_rate_valid: @rx_rate is valid
3970 * @rtt_avg_valid: @rtt_avg is valid
3971 * @rtt_variance_valid: @rtt_variance is valid
3972 * @rtt_spread_valid: @rtt_spread is valid
3973 * @dist_avg_valid: @dist_avg is valid
3974 * @dist_variance_valid: @dist_variance is valid
3975 * @dist_spread_valid: @dist_spread is valid
3976 */
3977struct cfg80211_pmsr_ftm_result {
3978 const u8 *lci;
3979 const u8 *civicloc;
3980 unsigned int lci_len;
3981 unsigned int civicloc_len;
3982 enum nl80211_peer_measurement_ftm_failure_reasons failure_reason;
3983 u32 num_ftmr_attempts, num_ftmr_successes;
3984 s16 burst_index;
3985 u8 busy_retry_time;
3986 u8 num_bursts_exp;
3987 u8 burst_duration;
3988 u8 ftms_per_burst;
3989 s32 rssi_avg;
3990 s32 rssi_spread;
3991 struct rate_info tx_rate, rx_rate;
3992 s64 rtt_avg;
3993 s64 rtt_variance;
3994 s64 rtt_spread;
3995 s64 dist_avg;
3996 s64 dist_variance;
3997 s64 dist_spread;
3998
3999 u16 num_ftmr_attempts_valid:1,
4000 num_ftmr_successes_valid:1,
4001 rssi_avg_valid:1,
4002 rssi_spread_valid:1,
4003 tx_rate_valid:1,
4004 rx_rate_valid:1,
4005 rtt_avg_valid:1,
4006 rtt_variance_valid:1,
4007 rtt_spread_valid:1,
4008 dist_avg_valid:1,
4009 dist_variance_valid:1,
4010 dist_spread_valid:1;
4011};
4012
4013/**
4014 * struct cfg80211_pmsr_result - peer measurement result
4015 * @addr: address of the peer
4016 * @host_time: host time (use ktime_get_boottime() adjust to the time when the
4017 * measurement was made)
4018 * @ap_tsf: AP's TSF at measurement time
4019 * @status: status of the measurement
4020 * @final: if reporting partial results, mark this as the last one; if not
4021 * reporting partial results always set this flag
4022 * @ap_tsf_valid: indicates the @ap_tsf value is valid
4023 * @type: type of the measurement reported, note that we only support reporting
4024 * one type at a time, but you can report multiple results separately and
4025 * they're all aggregated for userspace.
4026 * @ftm: FTM result
4027 */
4028struct cfg80211_pmsr_result {
4029 u64 host_time, ap_tsf;
4030 enum nl80211_peer_measurement_status status;
4031
4032 u8 addr[ETH_ALEN];
4033
4034 u8 final:1,
4035 ap_tsf_valid:1;
4036
4037 enum nl80211_peer_measurement_type type;
4038
4039 union {
4040 struct cfg80211_pmsr_ftm_result ftm;
4041 };
4042};
4043
4044/**
4045 * struct cfg80211_pmsr_ftm_request_peer - FTM request data
4046 * @requested: indicates FTM is requested
4047 * @preamble: frame preamble to use
4048 * @burst_period: burst period to use
4049 * @asap: indicates to use ASAP mode
4050 * @num_bursts_exp: number of bursts exponent
4051 * @burst_duration: burst duration
4052 * @ftms_per_burst: number of FTMs per burst
4053 * @ftmr_retries: number of retries for FTM request
4054 * @request_lci: request LCI information
4055 * @request_civicloc: request civic location information
4056 * @trigger_based: use trigger based ranging for the measurement
4057 * If neither @trigger_based nor @non_trigger_based is set,
4058 * EDCA based ranging will be used.
4059 * @non_trigger_based: use non trigger based ranging for the measurement
4060 * If neither @trigger_based nor @non_trigger_based is set,
4061 * EDCA based ranging will be used.
4062 * @lmr_feedback: negotiate for I2R LMR feedback. Only valid if either
4063 * @trigger_based or @non_trigger_based is set.
4064 * @bss_color: the bss color of the responder. Optional. Set to zero to
4065 * indicate the driver should set the BSS color. Only valid if
4066 * @non_trigger_based or @trigger_based is set.
4067 *
4068 * See also nl80211 for the respective attribute documentation.
4069 */
4070struct cfg80211_pmsr_ftm_request_peer {
4071 enum nl80211_preamble preamble;
4072 u16 burst_period;
4073 u8 requested:1,
4074 asap:1,
4075 request_lci:1,
4076 request_civicloc:1,
4077 trigger_based:1,
4078 non_trigger_based:1,
4079 lmr_feedback:1;
4080 u8 num_bursts_exp;
4081 u8 burst_duration;
4082 u8 ftms_per_burst;
4083 u8 ftmr_retries;
4084 u8 bss_color;
4085};
4086
4087/**
4088 * struct cfg80211_pmsr_request_peer - peer data for a peer measurement request
4089 * @addr: MAC address
4090 * @chandef: channel to use
4091 * @report_ap_tsf: report the associated AP's TSF
4092 * @ftm: FTM data, see &struct cfg80211_pmsr_ftm_request_peer
4093 */
4094struct cfg80211_pmsr_request_peer {
4095 u8 addr[ETH_ALEN];
4096 struct cfg80211_chan_def chandef;
4097 u8 report_ap_tsf:1;
4098 struct cfg80211_pmsr_ftm_request_peer ftm;
4099};
4100
4101/**
4102 * struct cfg80211_pmsr_request - peer measurement request
4103 * @cookie: cookie, set by cfg80211
4104 * @nl_portid: netlink portid - used by cfg80211
4105 * @drv_data: driver data for this request, if required for aborting,
4106 * not otherwise freed or anything by cfg80211
4107 * @mac_addr: MAC address used for (randomised) request
4108 * @mac_addr_mask: MAC address mask used for randomisation, bits that
4109 * are 0 in the mask should be randomised, bits that are 1 should
4110 * be taken from the @mac_addr
4111 * @list: used by cfg80211 to hold on to the request
4112 * @timeout: timeout (in milliseconds) for the whole operation, if
4113 * zero it means there's no timeout
4114 * @n_peers: number of peers to do measurements with
4115 * @peers: per-peer measurement request data
4116 */
4117struct cfg80211_pmsr_request {
4118 u64 cookie;
4119 void *drv_data;
4120 u32 n_peers;
4121 u32 nl_portid;
4122
4123 u32 timeout;
4124
4125 u8 mac_addr[ETH_ALEN] __aligned(2);
4126 u8 mac_addr_mask[ETH_ALEN] __aligned(2);
4127
4128 struct list_head list;
4129
4130 struct cfg80211_pmsr_request_peer peers[] __counted_by(n_peers);
4131};
4132
4133/**
4134 * struct cfg80211_update_owe_info - OWE Information
4135 *
4136 * This structure provides information needed for the drivers to offload OWE
4137 * (Opportunistic Wireless Encryption) processing to the user space.
4138 *
4139 * Commonly used across update_owe_info request and event interfaces.
4140 *
4141 * @peer: MAC address of the peer device for which the OWE processing
4142 * has to be done.
4143 * @status: status code, %WLAN_STATUS_SUCCESS for successful OWE info
4144 * processing, use %WLAN_STATUS_UNSPECIFIED_FAILURE if user space
4145 * cannot give you the real status code for failures. Used only for
4146 * OWE update request command interface (user space to driver).
4147 * @ie: IEs obtained from the peer or constructed by the user space. These are
4148 * the IEs of the remote peer in the event from the host driver and
4149 * the constructed IEs by the user space in the request interface.
4150 * @ie_len: Length of IEs in octets.
4151 * @assoc_link_id: MLO link ID of the AP, with which (re)association requested
4152 * by peer. This will be filled by driver for both MLO and non-MLO station
4153 * connections when the AP affiliated with an MLD. For non-MLD AP mode, it
4154 * will be -1. Used only with OWE update event (driver to user space).
4155 * @peer_mld_addr: For MLO connection, MLD address of the peer. For non-MLO
4156 * connection, it will be all zeros. This is applicable only when
4157 * @assoc_link_id is not -1, i.e., the AP affiliated with an MLD. Used only
4158 * with OWE update event (driver to user space).
4159 */
4160struct cfg80211_update_owe_info {
4161 u8 peer[ETH_ALEN] __aligned(2);
4162 u16 status;
4163 const u8 *ie;
4164 size_t ie_len;
4165 int assoc_link_id;
4166 u8 peer_mld_addr[ETH_ALEN] __aligned(2);
4167};
4168
4169/**
4170 * struct mgmt_frame_regs - management frame registrations data
4171 * @global_stypes: bitmap of management frame subtypes registered
4172 * for the entire device
4173 * @interface_stypes: bitmap of management frame subtypes registered
4174 * for the given interface
4175 * @global_mcast_stypes: mcast RX is needed globally for these subtypes
4176 * @interface_mcast_stypes: mcast RX is needed on this interface
4177 * for these subtypes
4178 */
4179struct mgmt_frame_regs {
4180 u32 global_stypes, interface_stypes;
4181 u32 global_mcast_stypes, interface_mcast_stypes;
4182};
4183
4184/**
4185 * struct cfg80211_ops - backend description for wireless configuration
4186 *
4187 * This struct is registered by fullmac card drivers and/or wireless stacks
4188 * in order to handle configuration requests on their interfaces.
4189 *
4190 * All callbacks except where otherwise noted should return 0
4191 * on success or a negative error code.
4192 *
4193 * All operations are invoked with the wiphy mutex held. The RTNL may be
4194 * held in addition (due to wireless extensions) but this cannot be relied
4195 * upon except in cases where documented below. Note that due to ordering,
4196 * the RTNL also cannot be acquired in any handlers.
4197 *
4198 * @suspend: wiphy device needs to be suspended. The variable @wow will
4199 * be %NULL or contain the enabled Wake-on-Wireless triggers that are
4200 * configured for the device.
4201 * @resume: wiphy device needs to be resumed
4202 * @set_wakeup: Called when WoWLAN is enabled/disabled, use this callback
4203 * to call device_set_wakeup_enable() to enable/disable wakeup from
4204 * the device.
4205 *
4206 * @add_virtual_intf: create a new virtual interface with the given name,
4207 * must set the struct wireless_dev's iftype. Beware: You must create
4208 * the new netdev in the wiphy's network namespace! Returns the struct
4209 * wireless_dev, or an ERR_PTR. For P2P device wdevs, the driver must
4210 * also set the address member in the wdev.
4211 * This additionally holds the RTNL to be able to do netdev changes.
4212 *
4213 * @del_virtual_intf: remove the virtual interface
4214 * This additionally holds the RTNL to be able to do netdev changes.
4215 *
4216 * @change_virtual_intf: change type/configuration of virtual interface,
4217 * keep the struct wireless_dev's iftype updated.
4218 * This additionally holds the RTNL to be able to do netdev changes.
4219 *
4220 * @add_intf_link: Add a new MLO link to the given interface. Note that
4221 * the wdev->link[] data structure has been updated, so the new link
4222 * address is available.
4223 * @del_intf_link: Remove an MLO link from the given interface.
4224 *
4225 * @add_key: add a key with the given parameters. @mac_addr will be %NULL
4226 * when adding a group key. @link_id will be -1 for non-MLO connection.
4227 * For MLO connection, @link_id will be >= 0 for group key and -1 for
4228 * pairwise key, @mac_addr will be peer's MLD address for MLO pairwise key.
4229 *
4230 * @get_key: get information about the key with the given parameters.
4231 * @mac_addr will be %NULL when requesting information for a group
4232 * key. All pointers given to the @callback function need not be valid
4233 * after it returns. This function should return an error if it is
4234 * not possible to retrieve the key, -ENOENT if it doesn't exist.
4235 * @link_id will be -1 for non-MLO connection. For MLO connection,
4236 * @link_id will be >= 0 for group key and -1 for pairwise key, @mac_addr
4237 * will be peer's MLD address for MLO pairwise key.
4238 *
4239 * @del_key: remove a key given the @mac_addr (%NULL for a group key)
4240 * and @key_index, return -ENOENT if the key doesn't exist. @link_id will
4241 * be -1 for non-MLO connection. For MLO connection, @link_id will be >= 0
4242 * for group key and -1 for pairwise key, @mac_addr will be peer's MLD
4243 * address for MLO pairwise key.
4244 *
4245 * @set_default_key: set the default key on an interface. @link_id will be >= 0
4246 * for MLO connection and -1 for non-MLO connection.
4247 *
4248 * @set_default_mgmt_key: set the default management frame key on an interface.
4249 * @link_id will be >= 0 for MLO connection and -1 for non-MLO connection.
4250 *
4251 * @set_default_beacon_key: set the default Beacon frame key on an interface.
4252 * @link_id will be >= 0 for MLO connection and -1 for non-MLO connection.
4253 *
4254 * @set_rekey_data: give the data necessary for GTK rekeying to the driver
4255 *
4256 * @start_ap: Start acting in AP mode defined by the parameters.
4257 * @change_beacon: Change the beacon parameters for an access point mode
4258 * interface. This should reject the call when AP mode wasn't started.
4259 * @stop_ap: Stop being an AP, including stopping beaconing.
4260 *
4261 * @add_station: Add a new station.
4262 * @del_station: Remove a station
4263 * @change_station: Modify a given station. Note that flags changes are not much
4264 * validated in cfg80211, in particular the auth/assoc/authorized flags
4265 * might come to the driver in invalid combinations -- make sure to check
4266 * them, also against the existing state! Drivers must call
4267 * cfg80211_check_station_change() to validate the information.
4268 * @get_station: get station information for the station identified by @mac
4269 * @dump_station: dump station callback -- resume dump at index @idx
4270 *
4271 * @add_mpath: add a fixed mesh path
4272 * @del_mpath: delete a given mesh path
4273 * @change_mpath: change a given mesh path
4274 * @get_mpath: get a mesh path for the given parameters
4275 * @dump_mpath: dump mesh path callback -- resume dump at index @idx
4276 * @get_mpp: get a mesh proxy path for the given parameters
4277 * @dump_mpp: dump mesh proxy path callback -- resume dump at index @idx
4278 * @join_mesh: join the mesh network with the specified parameters
4279 * (invoked with the wireless_dev mutex held)
4280 * @leave_mesh: leave the current mesh network
4281 * (invoked with the wireless_dev mutex held)
4282 *
4283 * @get_mesh_config: Get the current mesh configuration
4284 *
4285 * @update_mesh_config: Update mesh parameters on a running mesh.
4286 * The mask is a bitfield which tells us which parameters to
4287 * set, and which to leave alone.
4288 *
4289 * @change_bss: Modify parameters for a given BSS.
4290 *
4291 * @inform_bss: Called by cfg80211 while being informed about new BSS data
4292 * for every BSS found within the reported data or frame. This is called
4293 * from within the cfg8011 inform_bss handlers while holding the bss_lock.
4294 * The data parameter is passed through from drv_data inside
4295 * struct cfg80211_inform_bss.
4296 * The new IE data for the BSS is explicitly passed.
4297 *
4298 * @set_txq_params: Set TX queue parameters
4299 *
4300 * @libertas_set_mesh_channel: Only for backward compatibility for libertas,
4301 * as it doesn't implement join_mesh and needs to set the channel to
4302 * join the mesh instead.
4303 *
4304 * @set_monitor_channel: Set the monitor mode channel for the device. If other
4305 * interfaces are active this callback should reject the configuration.
4306 * If no interfaces are active or the device is down, the channel should
4307 * be stored for when a monitor interface becomes active.
4308 *
4309 * @scan: Request to do a scan. If returning zero, the scan request is given
4310 * the driver, and will be valid until passed to cfg80211_scan_done().
4311 * For scan results, call cfg80211_inform_bss(); you can call this outside
4312 * the scan/scan_done bracket too.
4313 * @abort_scan: Tell the driver to abort an ongoing scan. The driver shall
4314 * indicate the status of the scan through cfg80211_scan_done().
4315 *
4316 * @auth: Request to authenticate with the specified peer
4317 * (invoked with the wireless_dev mutex held)
4318 * @assoc: Request to (re)associate with the specified peer
4319 * (invoked with the wireless_dev mutex held)
4320 * @deauth: Request to deauthenticate from the specified peer
4321 * (invoked with the wireless_dev mutex held)
4322 * @disassoc: Request to disassociate from the specified peer
4323 * (invoked with the wireless_dev mutex held)
4324 *
4325 * @connect: Connect to the ESS with the specified parameters. When connected,
4326 * call cfg80211_connect_result()/cfg80211_connect_bss() with status code
4327 * %WLAN_STATUS_SUCCESS. If the connection fails for some reason, call
4328 * cfg80211_connect_result()/cfg80211_connect_bss() with the status code
4329 * from the AP or cfg80211_connect_timeout() if no frame with status code
4330 * was received.
4331 * The driver is allowed to roam to other BSSes within the ESS when the
4332 * other BSS matches the connect parameters. When such roaming is initiated
4333 * by the driver, the driver is expected to verify that the target matches
4334 * the configured security parameters and to use Reassociation Request
4335 * frame instead of Association Request frame.
4336 * The connect function can also be used to request the driver to perform a
4337 * specific roam when connected to an ESS. In that case, the prev_bssid
4338 * parameter is set to the BSSID of the currently associated BSS as an
4339 * indication of requesting reassociation.
4340 * In both the driver-initiated and new connect() call initiated roaming
4341 * cases, the result of roaming is indicated with a call to
4342 * cfg80211_roamed(). (invoked with the wireless_dev mutex held)
4343 * @update_connect_params: Update the connect parameters while connected to a
4344 * BSS. The updated parameters can be used by driver/firmware for
4345 * subsequent BSS selection (roaming) decisions and to form the
4346 * Authentication/(Re)Association Request frames. This call does not
4347 * request an immediate disassociation or reassociation with the current
4348 * BSS, i.e., this impacts only subsequent (re)associations. The bits in
4349 * changed are defined in &enum cfg80211_connect_params_changed.
4350 * (invoked with the wireless_dev mutex held)
4351 * @disconnect: Disconnect from the BSS/ESS or stop connection attempts if
4352 * connection is in progress. Once done, call cfg80211_disconnected() in
4353 * case connection was already established (invoked with the
4354 * wireless_dev mutex held), otherwise call cfg80211_connect_timeout().
4355 *
4356 * @join_ibss: Join the specified IBSS (or create if necessary). Once done, call
4357 * cfg80211_ibss_joined(), also call that function when changing BSSID due
4358 * to a merge.
4359 * (invoked with the wireless_dev mutex held)
4360 * @leave_ibss: Leave the IBSS.
4361 * (invoked with the wireless_dev mutex held)
4362 *
4363 * @set_mcast_rate: Set the specified multicast rate (only if vif is in ADHOC or
4364 * MESH mode)
4365 *
4366 * @set_wiphy_params: Notify that wiphy parameters have changed;
4367 * @changed bitfield (see &enum wiphy_params_flags) describes which values
4368 * have changed. The actual parameter values are available in
4369 * struct wiphy. If returning an error, no value should be changed.
4370 *
4371 * @set_tx_power: set the transmit power according to the parameters,
4372 * the power passed is in mBm, to get dBm use MBM_TO_DBM(). The
4373 * wdev may be %NULL if power was set for the wiphy, and will
4374 * always be %NULL unless the driver supports per-vif TX power
4375 * (as advertised by the nl80211 feature flag.)
4376 * @get_tx_power: store the current TX power into the dbm variable;
4377 * return 0 if successful
4378 *
4379 * @rfkill_poll: polls the hw rfkill line, use cfg80211 reporting
4380 * functions to adjust rfkill hw state
4381 *
4382 * @dump_survey: get site survey information.
4383 *
4384 * @remain_on_channel: Request the driver to remain awake on the specified
4385 * channel for the specified duration to complete an off-channel
4386 * operation (e.g., public action frame exchange). When the driver is
4387 * ready on the requested channel, it must indicate this with an event
4388 * notification by calling cfg80211_ready_on_channel().
4389 * @cancel_remain_on_channel: Cancel an on-going remain-on-channel operation.
4390 * This allows the operation to be terminated prior to timeout based on
4391 * the duration value.
4392 * @mgmt_tx: Transmit a management frame.
4393 * @mgmt_tx_cancel_wait: Cancel the wait time from transmitting a management
4394 * frame on another channel
4395 *
4396 * @testmode_cmd: run a test mode command; @wdev may be %NULL
4397 * @testmode_dump: Implement a test mode dump. The cb->args[2] and up may be
4398 * used by the function, but 0 and 1 must not be touched. Additionally,
4399 * return error codes other than -ENOBUFS and -ENOENT will terminate the
4400 * dump and return to userspace with an error, so be careful. If any data
4401 * was passed in from userspace then the data/len arguments will be present
4402 * and point to the data contained in %NL80211_ATTR_TESTDATA.
4403 *
4404 * @set_bitrate_mask: set the bitrate mask configuration
4405 *
4406 * @set_pmksa: Cache a PMKID for a BSSID. This is mostly useful for fullmac
4407 * devices running firmwares capable of generating the (re) association
4408 * RSN IE. It allows for faster roaming between WPA2 BSSIDs.
4409 * @del_pmksa: Delete a cached PMKID.
4410 * @flush_pmksa: Flush all cached PMKIDs.
4411 * @set_power_mgmt: Configure WLAN power management. A timeout value of -1
4412 * allows the driver to adjust the dynamic ps timeout value.
4413 * @set_cqm_rssi_config: Configure connection quality monitor RSSI threshold.
4414 * After configuration, the driver should (soon) send an event indicating
4415 * the current level is above/below the configured threshold; this may
4416 * need some care when the configuration is changed (without first being
4417 * disabled.)
4418 * @set_cqm_rssi_range_config: Configure two RSSI thresholds in the
4419 * connection quality monitor. An event is to be sent only when the
4420 * signal level is found to be outside the two values. The driver should
4421 * set %NL80211_EXT_FEATURE_CQM_RSSI_LIST if this method is implemented.
4422 * If it is provided then there's no point providing @set_cqm_rssi_config.
4423 * @set_cqm_txe_config: Configure connection quality monitor TX error
4424 * thresholds.
4425 * @sched_scan_start: Tell the driver to start a scheduled scan.
4426 * @sched_scan_stop: Tell the driver to stop an ongoing scheduled scan with
4427 * given request id. This call must stop the scheduled scan and be ready
4428 * for starting a new one before it returns, i.e. @sched_scan_start may be
4429 * called immediately after that again and should not fail in that case.
4430 * The driver should not call cfg80211_sched_scan_stopped() for a requested
4431 * stop (when this method returns 0).
4432 *
4433 * @update_mgmt_frame_registrations: Notify the driver that management frame
4434 * registrations were updated. The callback is allowed to sleep.
4435 *
4436 * @set_antenna: Set antenna configuration (tx_ant, rx_ant) on the device.
4437 * Parameters are bitmaps of allowed antennas to use for TX/RX. Drivers may
4438 * reject TX/RX mask combinations they cannot support by returning -EINVAL
4439 * (also see nl80211.h @NL80211_ATTR_WIPHY_ANTENNA_TX).
4440 *
4441 * @get_antenna: Get current antenna configuration from device (tx_ant, rx_ant).
4442 *
4443 * @tdls_mgmt: Transmit a TDLS management frame.
4444 * @tdls_oper: Perform a high-level TDLS operation (e.g. TDLS link setup).
4445 *
4446 * @probe_client: probe an associated client, must return a cookie that it
4447 * later passes to cfg80211_probe_status().
4448 *
4449 * @set_noack_map: Set the NoAck Map for the TIDs.
4450 *
4451 * @get_channel: Get the current operating channel for the virtual interface.
4452 * For monitor interfaces, it should return %NULL unless there's a single
4453 * current monitoring channel.
4454 *
4455 * @start_p2p_device: Start the given P2P device.
4456 * @stop_p2p_device: Stop the given P2P device.
4457 *
4458 * @set_mac_acl: Sets MAC address control list in AP and P2P GO mode.
4459 * Parameters include ACL policy, an array of MAC address of stations
4460 * and the number of MAC addresses. If there is already a list in driver
4461 * this new list replaces the existing one. Driver has to clear its ACL
4462 * when number of MAC addresses entries is passed as 0. Drivers which
4463 * advertise the support for MAC based ACL have to implement this callback.
4464 *
4465 * @start_radar_detection: Start radar detection in the driver.
4466 *
4467 * @end_cac: End running CAC, probably because a related CAC
4468 * was finished on another phy.
4469 *
4470 * @update_ft_ies: Provide updated Fast BSS Transition information to the
4471 * driver. If the SME is in the driver/firmware, this information can be
4472 * used in building Authentication and Reassociation Request frames.
4473 *
4474 * @crit_proto_start: Indicates a critical protocol needs more link reliability
4475 * for a given duration (milliseconds). The protocol is provided so the
4476 * driver can take the most appropriate actions.
4477 * @crit_proto_stop: Indicates critical protocol no longer needs increased link
4478 * reliability. This operation can not fail.
4479 * @set_coalesce: Set coalesce parameters.
4480 *
4481 * @channel_switch: initiate channel-switch procedure (with CSA). Driver is
4482 * responsible for veryfing if the switch is possible. Since this is
4483 * inherently tricky driver may decide to disconnect an interface later
4484 * with cfg80211_stop_iface(). This doesn't mean driver can accept
4485 * everything. It should do it's best to verify requests and reject them
4486 * as soon as possible.
4487 *
4488 * @set_qos_map: Set QoS mapping information to the driver
4489 *
4490 * @set_ap_chanwidth: Set the AP (including P2P GO) mode channel width for the
4491 * given interface This is used e.g. for dynamic HT 20/40 MHz channel width
4492 * changes during the lifetime of the BSS.
4493 *
4494 * @add_tx_ts: validate (if admitted_time is 0) or add a TX TS to the device
4495 * with the given parameters; action frame exchange has been handled by
4496 * userspace so this just has to modify the TX path to take the TS into
4497 * account.
4498 * If the admitted time is 0 just validate the parameters to make sure
4499 * the session can be created at all; it is valid to just always return
4500 * success for that but that may result in inefficient behaviour (handshake
4501 * with the peer followed by immediate teardown when the addition is later
4502 * rejected)
4503 * @del_tx_ts: remove an existing TX TS
4504 *
4505 * @join_ocb: join the OCB network with the specified parameters
4506 * (invoked with the wireless_dev mutex held)
4507 * @leave_ocb: leave the current OCB network
4508 * (invoked with the wireless_dev mutex held)
4509 *
4510 * @tdls_channel_switch: Start channel-switching with a TDLS peer. The driver
4511 * is responsible for continually initiating channel-switching operations
4512 * and returning to the base channel for communication with the AP.
4513 * @tdls_cancel_channel_switch: Stop channel-switching with a TDLS peer. Both
4514 * peers must be on the base channel when the call completes.
4515 * @start_nan: Start the NAN interface.
4516 * @stop_nan: Stop the NAN interface.
4517 * @add_nan_func: Add a NAN function. Returns negative value on failure.
4518 * On success @nan_func ownership is transferred to the driver and
4519 * it may access it outside of the scope of this function. The driver
4520 * should free the @nan_func when no longer needed by calling
4521 * cfg80211_free_nan_func().
4522 * On success the driver should assign an instance_id in the
4523 * provided @nan_func.
4524 * @del_nan_func: Delete a NAN function.
4525 * @nan_change_conf: changes NAN configuration. The changed parameters must
4526 * be specified in @changes (using &enum cfg80211_nan_conf_changes);
4527 * All other parameters must be ignored.
4528 *
4529 * @set_multicast_to_unicast: configure multicast to unicast conversion for BSS
4530 *
4531 * @get_txq_stats: Get TXQ stats for interface or phy. If wdev is %NULL, this
4532 * function should return phy stats, and interface stats otherwise.
4533 *
4534 * @set_pmk: configure the PMK to be used for offloaded 802.1X 4-Way handshake.
4535 * If not deleted through @del_pmk the PMK remains valid until disconnect
4536 * upon which the driver should clear it.
4537 * (invoked with the wireless_dev mutex held)
4538 * @del_pmk: delete the previously configured PMK for the given authenticator.
4539 * (invoked with the wireless_dev mutex held)
4540 *
4541 * @external_auth: indicates result of offloaded authentication processing from
4542 * user space
4543 *
4544 * @tx_control_port: TX a control port frame (EAPoL). The noencrypt parameter
4545 * tells the driver that the frame should not be encrypted.
4546 *
4547 * @get_ftm_responder_stats: Retrieve FTM responder statistics, if available.
4548 * Statistics should be cumulative, currently no way to reset is provided.
4549 * @start_pmsr: start peer measurement (e.g. FTM)
4550 * @abort_pmsr: abort peer measurement
4551 *
4552 * @update_owe_info: Provide updated OWE info to driver. Driver implementing SME
4553 * but offloading OWE processing to the user space will get the updated
4554 * DH IE through this interface.
4555 *
4556 * @probe_mesh_link: Probe direct Mesh peer's link quality by sending data frame
4557 * and overrule HWMP path selection algorithm.
4558 * @set_tid_config: TID specific configuration, this can be peer or BSS specific
4559 * This callback may sleep.
4560 * @reset_tid_config: Reset TID specific configuration for the peer, for the
4561 * given TIDs. This callback may sleep.
4562 *
4563 * @set_sar_specs: Update the SAR (TX power) settings.
4564 *
4565 * @color_change: Initiate a color change.
4566 *
4567 * @set_fils_aad: Set FILS AAD data to the AP driver so that the driver can use
4568 * those to decrypt (Re)Association Request and encrypt (Re)Association
4569 * Response frame.
4570 *
4571 * @set_radar_background: Configure dedicated offchannel chain available for
4572 * radar/CAC detection on some hw. This chain can't be used to transmit
4573 * or receive frames and it is bounded to a running wdev.
4574 * Background radar/CAC detection allows to avoid the CAC downtime
4575 * switching to a different channel during CAC detection on the selected
4576 * radar channel.
4577 * The caller is expected to set chandef pointer to NULL in order to
4578 * disable background CAC/radar detection.
4579 * @add_link_station: Add a link to a station.
4580 * @mod_link_station: Modify a link of a station.
4581 * @del_link_station: Remove a link of a station.
4582 *
4583 * @set_hw_timestamp: Enable/disable HW timestamping of TM/FTM frames.
4584 * @set_ttlm: set the TID to link mapping.
4585 * @get_radio_mask: get bitmask of radios in use.
4586 * (invoked with the wiphy mutex held)
4587 */
4588struct cfg80211_ops {
4589 int (*suspend)(struct wiphy *wiphy, struct cfg80211_wowlan *wow);
4590 int (*resume)(struct wiphy *wiphy);
4591 void (*set_wakeup)(struct wiphy *wiphy, bool enabled);
4592
4593 struct wireless_dev * (*add_virtual_intf)(struct wiphy *wiphy,
4594 const char *name,
4595 unsigned char name_assign_type,
4596 enum nl80211_iftype type,
4597 struct vif_params *params);
4598 int (*del_virtual_intf)(struct wiphy *wiphy,
4599 struct wireless_dev *wdev);
4600 int (*change_virtual_intf)(struct wiphy *wiphy,
4601 struct net_device *dev,
4602 enum nl80211_iftype type,
4603 struct vif_params *params);
4604
4605 int (*add_intf_link)(struct wiphy *wiphy,
4606 struct wireless_dev *wdev,
4607 unsigned int link_id);
4608 void (*del_intf_link)(struct wiphy *wiphy,
4609 struct wireless_dev *wdev,
4610 unsigned int link_id);
4611
4612 int (*add_key)(struct wiphy *wiphy, struct net_device *netdev,
4613 int link_id, u8 key_index, bool pairwise,
4614 const u8 *mac_addr, struct key_params *params);
4615 int (*get_key)(struct wiphy *wiphy, struct net_device *netdev,
4616 int link_id, u8 key_index, bool pairwise,
4617 const u8 *mac_addr, void *cookie,
4618 void (*callback)(void *cookie, struct key_params*));
4619 int (*del_key)(struct wiphy *wiphy, struct net_device *netdev,
4620 int link_id, u8 key_index, bool pairwise,
4621 const u8 *mac_addr);
4622 int (*set_default_key)(struct wiphy *wiphy,
4623 struct net_device *netdev, int link_id,
4624 u8 key_index, bool unicast, bool multicast);
4625 int (*set_default_mgmt_key)(struct wiphy *wiphy,
4626 struct net_device *netdev, int link_id,
4627 u8 key_index);
4628 int (*set_default_beacon_key)(struct wiphy *wiphy,
4629 struct net_device *netdev,
4630 int link_id,
4631 u8 key_index);
4632
4633 int (*start_ap)(struct wiphy *wiphy, struct net_device *dev,
4634 struct cfg80211_ap_settings *settings);
4635 int (*change_beacon)(struct wiphy *wiphy, struct net_device *dev,
4636 struct cfg80211_ap_update *info);
4637 int (*stop_ap)(struct wiphy *wiphy, struct net_device *dev,
4638 unsigned int link_id);
4639
4640
4641 int (*add_station)(struct wiphy *wiphy, struct net_device *dev,
4642 const u8 *mac,
4643 struct station_parameters *params);
4644 int (*del_station)(struct wiphy *wiphy, struct net_device *dev,
4645 struct station_del_parameters *params);
4646 int (*change_station)(struct wiphy *wiphy, struct net_device *dev,
4647 const u8 *mac,
4648 struct station_parameters *params);
4649 int (*get_station)(struct wiphy *wiphy, struct net_device *dev,
4650 const u8 *mac, struct station_info *sinfo);
4651 int (*dump_station)(struct wiphy *wiphy, struct net_device *dev,
4652 int idx, u8 *mac, struct station_info *sinfo);
4653
4654 int (*add_mpath)(struct wiphy *wiphy, struct net_device *dev,
4655 const u8 *dst, const u8 *next_hop);
4656 int (*del_mpath)(struct wiphy *wiphy, struct net_device *dev,
4657 const u8 *dst);
4658 int (*change_mpath)(struct wiphy *wiphy, struct net_device *dev,
4659 const u8 *dst, const u8 *next_hop);
4660 int (*get_mpath)(struct wiphy *wiphy, struct net_device *dev,
4661 u8 *dst, u8 *next_hop, struct mpath_info *pinfo);
4662 int (*dump_mpath)(struct wiphy *wiphy, struct net_device *dev,
4663 int idx, u8 *dst, u8 *next_hop,
4664 struct mpath_info *pinfo);
4665 int (*get_mpp)(struct wiphy *wiphy, struct net_device *dev,
4666 u8 *dst, u8 *mpp, struct mpath_info *pinfo);
4667 int (*dump_mpp)(struct wiphy *wiphy, struct net_device *dev,
4668 int idx, u8 *dst, u8 *mpp,
4669 struct mpath_info *pinfo);
4670 int (*get_mesh_config)(struct wiphy *wiphy,
4671 struct net_device *dev,
4672 struct mesh_config *conf);
4673 int (*update_mesh_config)(struct wiphy *wiphy,
4674 struct net_device *dev, u32 mask,
4675 const struct mesh_config *nconf);
4676 int (*join_mesh)(struct wiphy *wiphy, struct net_device *dev,
4677 const struct mesh_config *conf,
4678 const struct mesh_setup *setup);
4679 int (*leave_mesh)(struct wiphy *wiphy, struct net_device *dev);
4680
4681 int (*join_ocb)(struct wiphy *wiphy, struct net_device *dev,
4682 struct ocb_setup *setup);
4683 int (*leave_ocb)(struct wiphy *wiphy, struct net_device *dev);
4684
4685 int (*change_bss)(struct wiphy *wiphy, struct net_device *dev,
4686 struct bss_parameters *params);
4687
4688 void (*inform_bss)(struct wiphy *wiphy, struct cfg80211_bss *bss,
4689 const struct cfg80211_bss_ies *ies, void *data);
4690
4691 int (*set_txq_params)(struct wiphy *wiphy, struct net_device *dev,
4692 struct ieee80211_txq_params *params);
4693
4694 int (*libertas_set_mesh_channel)(struct wiphy *wiphy,
4695 struct net_device *dev,
4696 struct ieee80211_channel *chan);
4697
4698 int (*set_monitor_channel)(struct wiphy *wiphy,
4699 struct net_device *dev,
4700 struct cfg80211_chan_def *chandef);
4701
4702 int (*scan)(struct wiphy *wiphy,
4703 struct cfg80211_scan_request *request);
4704 void (*abort_scan)(struct wiphy *wiphy, struct wireless_dev *wdev);
4705
4706 int (*auth)(struct wiphy *wiphy, struct net_device *dev,
4707 struct cfg80211_auth_request *req);
4708 int (*assoc)(struct wiphy *wiphy, struct net_device *dev,
4709 struct cfg80211_assoc_request *req);
4710 int (*deauth)(struct wiphy *wiphy, struct net_device *dev,
4711 struct cfg80211_deauth_request *req);
4712 int (*disassoc)(struct wiphy *wiphy, struct net_device *dev,
4713 struct cfg80211_disassoc_request *req);
4714
4715 int (*connect)(struct wiphy *wiphy, struct net_device *dev,
4716 struct cfg80211_connect_params *sme);
4717 int (*update_connect_params)(struct wiphy *wiphy,
4718 struct net_device *dev,
4719 struct cfg80211_connect_params *sme,
4720 u32 changed);
4721 int (*disconnect)(struct wiphy *wiphy, struct net_device *dev,
4722 u16 reason_code);
4723
4724 int (*join_ibss)(struct wiphy *wiphy, struct net_device *dev,
4725 struct cfg80211_ibss_params *params);
4726 int (*leave_ibss)(struct wiphy *wiphy, struct net_device *dev);
4727
4728 int (*set_mcast_rate)(struct wiphy *wiphy, struct net_device *dev,
4729 int rate[NUM_NL80211_BANDS]);
4730
4731 int (*set_wiphy_params)(struct wiphy *wiphy, u32 changed);
4732
4733 int (*set_tx_power)(struct wiphy *wiphy, struct wireless_dev *wdev,
4734 enum nl80211_tx_power_setting type, int mbm);
4735 int (*get_tx_power)(struct wiphy *wiphy, struct wireless_dev *wdev,
4736 int *dbm);
4737
4738 void (*rfkill_poll)(struct wiphy *wiphy);
4739
4740#ifdef CONFIG_NL80211_TESTMODE
4741 int (*testmode_cmd)(struct wiphy *wiphy, struct wireless_dev *wdev,
4742 void *data, int len);
4743 int (*testmode_dump)(struct wiphy *wiphy, struct sk_buff *skb,
4744 struct netlink_callback *cb,
4745 void *data, int len);
4746#endif
4747
4748 int (*set_bitrate_mask)(struct wiphy *wiphy,
4749 struct net_device *dev,
4750 unsigned int link_id,
4751 const u8 *peer,
4752 const struct cfg80211_bitrate_mask *mask);
4753
4754 int (*dump_survey)(struct wiphy *wiphy, struct net_device *netdev,
4755 int idx, struct survey_info *info);
4756
4757 int (*set_pmksa)(struct wiphy *wiphy, struct net_device *netdev,
4758 struct cfg80211_pmksa *pmksa);
4759 int (*del_pmksa)(struct wiphy *wiphy, struct net_device *netdev,
4760 struct cfg80211_pmksa *pmksa);
4761 int (*flush_pmksa)(struct wiphy *wiphy, struct net_device *netdev);
4762
4763 int (*remain_on_channel)(struct wiphy *wiphy,
4764 struct wireless_dev *wdev,
4765 struct ieee80211_channel *chan,
4766 unsigned int duration,
4767 u64 *cookie);
4768 int (*cancel_remain_on_channel)(struct wiphy *wiphy,
4769 struct wireless_dev *wdev,
4770 u64 cookie);
4771
4772 int (*mgmt_tx)(struct wiphy *wiphy, struct wireless_dev *wdev,
4773 struct cfg80211_mgmt_tx_params *params,
4774 u64 *cookie);
4775 int (*mgmt_tx_cancel_wait)(struct wiphy *wiphy,
4776 struct wireless_dev *wdev,
4777 u64 cookie);
4778
4779 int (*set_power_mgmt)(struct wiphy *wiphy, struct net_device *dev,
4780 bool enabled, int timeout);
4781
4782 int (*set_cqm_rssi_config)(struct wiphy *wiphy,
4783 struct net_device *dev,
4784 s32 rssi_thold, u32 rssi_hyst);
4785
4786 int (*set_cqm_rssi_range_config)(struct wiphy *wiphy,
4787 struct net_device *dev,
4788 s32 rssi_low, s32 rssi_high);
4789
4790 int (*set_cqm_txe_config)(struct wiphy *wiphy,
4791 struct net_device *dev,
4792 u32 rate, u32 pkts, u32 intvl);
4793
4794 void (*update_mgmt_frame_registrations)(struct wiphy *wiphy,
4795 struct wireless_dev *wdev,
4796 struct mgmt_frame_regs *upd);
4797
4798 int (*set_antenna)(struct wiphy *wiphy, u32 tx_ant, u32 rx_ant);
4799 int (*get_antenna)(struct wiphy *wiphy, u32 *tx_ant, u32 *rx_ant);
4800
4801 int (*sched_scan_start)(struct wiphy *wiphy,
4802 struct net_device *dev,
4803 struct cfg80211_sched_scan_request *request);
4804 int (*sched_scan_stop)(struct wiphy *wiphy, struct net_device *dev,
4805 u64 reqid);
4806
4807 int (*set_rekey_data)(struct wiphy *wiphy, struct net_device *dev,
4808 struct cfg80211_gtk_rekey_data *data);
4809
4810 int (*tdls_mgmt)(struct wiphy *wiphy, struct net_device *dev,
4811 const u8 *peer, int link_id,
4812 u8 action_code, u8 dialog_token, u16 status_code,
4813 u32 peer_capability, bool initiator,
4814 const u8 *buf, size_t len);
4815 int (*tdls_oper)(struct wiphy *wiphy, struct net_device *dev,
4816 const u8 *peer, enum nl80211_tdls_operation oper);
4817
4818 int (*probe_client)(struct wiphy *wiphy, struct net_device *dev,
4819 const u8 *peer, u64 *cookie);
4820
4821 int (*set_noack_map)(struct wiphy *wiphy,
4822 struct net_device *dev,
4823 u16 noack_map);
4824
4825 int (*get_channel)(struct wiphy *wiphy,
4826 struct wireless_dev *wdev,
4827 unsigned int link_id,
4828 struct cfg80211_chan_def *chandef);
4829
4830 int (*start_p2p_device)(struct wiphy *wiphy,
4831 struct wireless_dev *wdev);
4832 void (*stop_p2p_device)(struct wiphy *wiphy,
4833 struct wireless_dev *wdev);
4834
4835 int (*set_mac_acl)(struct wiphy *wiphy, struct net_device *dev,
4836 const struct cfg80211_acl_data *params);
4837
4838 int (*start_radar_detection)(struct wiphy *wiphy,
4839 struct net_device *dev,
4840 struct cfg80211_chan_def *chandef,
4841 u32 cac_time_ms, int link_id);
4842 void (*end_cac)(struct wiphy *wiphy,
4843 struct net_device *dev, unsigned int link_id);
4844 int (*update_ft_ies)(struct wiphy *wiphy, struct net_device *dev,
4845 struct cfg80211_update_ft_ies_params *ftie);
4846 int (*crit_proto_start)(struct wiphy *wiphy,
4847 struct wireless_dev *wdev,
4848 enum nl80211_crit_proto_id protocol,
4849 u16 duration);
4850 void (*crit_proto_stop)(struct wiphy *wiphy,
4851 struct wireless_dev *wdev);
4852 int (*set_coalesce)(struct wiphy *wiphy,
4853 struct cfg80211_coalesce *coalesce);
4854
4855 int (*channel_switch)(struct wiphy *wiphy,
4856 struct net_device *dev,
4857 struct cfg80211_csa_settings *params);
4858
4859 int (*set_qos_map)(struct wiphy *wiphy,
4860 struct net_device *dev,
4861 struct cfg80211_qos_map *qos_map);
4862
4863 int (*set_ap_chanwidth)(struct wiphy *wiphy, struct net_device *dev,
4864 unsigned int link_id,
4865 struct cfg80211_chan_def *chandef);
4866
4867 int (*add_tx_ts)(struct wiphy *wiphy, struct net_device *dev,
4868 u8 tsid, const u8 *peer, u8 user_prio,
4869 u16 admitted_time);
4870 int (*del_tx_ts)(struct wiphy *wiphy, struct net_device *dev,
4871 u8 tsid, const u8 *peer);
4872
4873 int (*tdls_channel_switch)(struct wiphy *wiphy,
4874 struct net_device *dev,
4875 const u8 *addr, u8 oper_class,
4876 struct cfg80211_chan_def *chandef);
4877 void (*tdls_cancel_channel_switch)(struct wiphy *wiphy,
4878 struct net_device *dev,
4879 const u8 *addr);
4880 int (*start_nan)(struct wiphy *wiphy, struct wireless_dev *wdev,
4881 struct cfg80211_nan_conf *conf);
4882 void (*stop_nan)(struct wiphy *wiphy, struct wireless_dev *wdev);
4883 int (*add_nan_func)(struct wiphy *wiphy, struct wireless_dev *wdev,
4884 struct cfg80211_nan_func *nan_func);
4885 void (*del_nan_func)(struct wiphy *wiphy, struct wireless_dev *wdev,
4886 u64 cookie);
4887 int (*nan_change_conf)(struct wiphy *wiphy,
4888 struct wireless_dev *wdev,
4889 struct cfg80211_nan_conf *conf,
4890 u32 changes);
4891
4892 int (*set_multicast_to_unicast)(struct wiphy *wiphy,
4893 struct net_device *dev,
4894 const bool enabled);
4895
4896 int (*get_txq_stats)(struct wiphy *wiphy,
4897 struct wireless_dev *wdev,
4898 struct cfg80211_txq_stats *txqstats);
4899
4900 int (*set_pmk)(struct wiphy *wiphy, struct net_device *dev,
4901 const struct cfg80211_pmk_conf *conf);
4902 int (*del_pmk)(struct wiphy *wiphy, struct net_device *dev,
4903 const u8 *aa);
4904 int (*external_auth)(struct wiphy *wiphy, struct net_device *dev,
4905 struct cfg80211_external_auth_params *params);
4906
4907 int (*tx_control_port)(struct wiphy *wiphy,
4908 struct net_device *dev,
4909 const u8 *buf, size_t len,
4910 const u8 *dest, const __be16 proto,
4911 const bool noencrypt, int link_id,
4912 u64 *cookie);
4913
4914 int (*get_ftm_responder_stats)(struct wiphy *wiphy,
4915 struct net_device *dev,
4916 struct cfg80211_ftm_responder_stats *ftm_stats);
4917
4918 int (*start_pmsr)(struct wiphy *wiphy, struct wireless_dev *wdev,
4919 struct cfg80211_pmsr_request *request);
4920 void (*abort_pmsr)(struct wiphy *wiphy, struct wireless_dev *wdev,
4921 struct cfg80211_pmsr_request *request);
4922 int (*update_owe_info)(struct wiphy *wiphy, struct net_device *dev,
4923 struct cfg80211_update_owe_info *owe_info);
4924 int (*probe_mesh_link)(struct wiphy *wiphy, struct net_device *dev,
4925 const u8 *buf, size_t len);
4926 int (*set_tid_config)(struct wiphy *wiphy, struct net_device *dev,
4927 struct cfg80211_tid_config *tid_conf);
4928 int (*reset_tid_config)(struct wiphy *wiphy, struct net_device *dev,
4929 const u8 *peer, u8 tids);
4930 int (*set_sar_specs)(struct wiphy *wiphy,
4931 struct cfg80211_sar_specs *sar);
4932 int (*color_change)(struct wiphy *wiphy,
4933 struct net_device *dev,
4934 struct cfg80211_color_change_settings *params);
4935 int (*set_fils_aad)(struct wiphy *wiphy, struct net_device *dev,
4936 struct cfg80211_fils_aad *fils_aad);
4937 int (*set_radar_background)(struct wiphy *wiphy,
4938 struct cfg80211_chan_def *chandef);
4939 int (*add_link_station)(struct wiphy *wiphy, struct net_device *dev,
4940 struct link_station_parameters *params);
4941 int (*mod_link_station)(struct wiphy *wiphy, struct net_device *dev,
4942 struct link_station_parameters *params);
4943 int (*del_link_station)(struct wiphy *wiphy, struct net_device *dev,
4944 struct link_station_del_parameters *params);
4945 int (*set_hw_timestamp)(struct wiphy *wiphy, struct net_device *dev,
4946 struct cfg80211_set_hw_timestamp *hwts);
4947 int (*set_ttlm)(struct wiphy *wiphy, struct net_device *dev,
4948 struct cfg80211_ttlm_params *params);
4949 u32 (*get_radio_mask)(struct wiphy *wiphy, struct net_device *dev);
4950};
4951
4952/*
4953 * wireless hardware and networking interfaces structures
4954 * and registration/helper functions
4955 */
4956
4957/**
4958 * enum wiphy_flags - wiphy capability flags
4959 *
4960 * @WIPHY_FLAG_SPLIT_SCAN_6GHZ: if set to true, the scan request will be split
4961 * into two, first for legacy bands and second for 6 GHz.
4962 * @WIPHY_FLAG_NETNS_OK: if not set, do not allow changing the netns of this
4963 * wiphy at all
4964 * @WIPHY_FLAG_PS_ON_BY_DEFAULT: if set to true, powersave will be enabled
4965 * by default -- this flag will be set depending on the kernel's default
4966 * on wiphy_new(), but can be changed by the driver if it has a good
4967 * reason to override the default
4968 * @WIPHY_FLAG_4ADDR_AP: supports 4addr mode even on AP (with a single station
4969 * on a VLAN interface). This flag also serves an extra purpose of
4970 * supporting 4ADDR AP mode on devices which do not support AP/VLAN iftype.
4971 * @WIPHY_FLAG_4ADDR_STATION: supports 4addr mode even as a station
4972 * @WIPHY_FLAG_CONTROL_PORT_PROTOCOL: This device supports setting the
4973 * control port protocol ethertype. The device also honours the
4974 * control_port_no_encrypt flag.
4975 * @WIPHY_FLAG_IBSS_RSN: The device supports IBSS RSN.
4976 * @WIPHY_FLAG_MESH_AUTH: The device supports mesh authentication by routing
4977 * auth frames to userspace. See @NL80211_MESH_SETUP_USERSPACE_AUTH.
4978 * @WIPHY_FLAG_SUPPORTS_FW_ROAM: The device supports roaming feature in the
4979 * firmware.
4980 * @WIPHY_FLAG_AP_UAPSD: The device supports uapsd on AP.
4981 * @WIPHY_FLAG_SUPPORTS_TDLS: The device supports TDLS (802.11z) operation.
4982 * @WIPHY_FLAG_TDLS_EXTERNAL_SETUP: The device does not handle TDLS (802.11z)
4983 * link setup/discovery operations internally. Setup, discovery and
4984 * teardown packets should be sent through the @NL80211_CMD_TDLS_MGMT
4985 * command. When this flag is not set, @NL80211_CMD_TDLS_OPER should be
4986 * used for asking the driver/firmware to perform a TDLS operation.
4987 * @WIPHY_FLAG_HAVE_AP_SME: device integrates AP SME
4988 * @WIPHY_FLAG_REPORTS_OBSS: the device will report beacons from other BSSes
4989 * when there are virtual interfaces in AP mode by calling
4990 * cfg80211_report_obss_beacon().
4991 * @WIPHY_FLAG_AP_PROBE_RESP_OFFLOAD: When operating as an AP, the device
4992 * responds to probe-requests in hardware.
4993 * @WIPHY_FLAG_OFFCHAN_TX: Device supports direct off-channel TX.
4994 * @WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL: Device supports remain-on-channel call.
4995 * @WIPHY_FLAG_SUPPORTS_5_10_MHZ: Device supports 5 MHz and 10 MHz channels.
4996 * @WIPHY_FLAG_HAS_CHANNEL_SWITCH: Device supports channel switch in
4997 * beaconing mode (AP, IBSS, Mesh, ...).
4998 * @WIPHY_FLAG_SUPPORTS_EXT_KEK_KCK: The device supports bigger kek and kck keys
4999 * @WIPHY_FLAG_SUPPORTS_MLO: This is a temporary flag gating the MLO APIs,
5000 * in order to not have them reachable in normal drivers, until we have
5001 * complete feature/interface combinations/etc. advertisement. No driver
5002 * should set this flag for now.
5003 * @WIPHY_FLAG_SUPPORTS_EXT_KCK_32: The device supports 32-byte KCK keys.
5004 * @WIPHY_FLAG_NOTIFY_REGDOM_BY_DRIVER: The device could handle reg notify for
5005 * NL80211_REGDOM_SET_BY_DRIVER.
5006 * @WIPHY_FLAG_CHANNEL_CHANGE_ON_BEACON: reg_call_notifier() is called if driver
5007 * set this flag to update channels on beacon hints.
5008 * @WIPHY_FLAG_SUPPORTS_NSTR_NONPRIMARY: support connection to non-primary link
5009 * of an NSTR mobile AP MLD.
5010 * @WIPHY_FLAG_DISABLE_WEXT: disable wireless extensions for this device
5011 */
5012enum wiphy_flags {
5013 WIPHY_FLAG_SUPPORTS_EXT_KEK_KCK = BIT(0),
5014 WIPHY_FLAG_SUPPORTS_MLO = BIT(1),
5015 WIPHY_FLAG_SPLIT_SCAN_6GHZ = BIT(2),
5016 WIPHY_FLAG_NETNS_OK = BIT(3),
5017 WIPHY_FLAG_PS_ON_BY_DEFAULT = BIT(4),
5018 WIPHY_FLAG_4ADDR_AP = BIT(5),
5019 WIPHY_FLAG_4ADDR_STATION = BIT(6),
5020 WIPHY_FLAG_CONTROL_PORT_PROTOCOL = BIT(7),
5021 WIPHY_FLAG_IBSS_RSN = BIT(8),
5022 WIPHY_FLAG_DISABLE_WEXT = BIT(9),
5023 WIPHY_FLAG_MESH_AUTH = BIT(10),
5024 WIPHY_FLAG_SUPPORTS_EXT_KCK_32 = BIT(11),
5025 WIPHY_FLAG_SUPPORTS_NSTR_NONPRIMARY = BIT(12),
5026 WIPHY_FLAG_SUPPORTS_FW_ROAM = BIT(13),
5027 WIPHY_FLAG_AP_UAPSD = BIT(14),
5028 WIPHY_FLAG_SUPPORTS_TDLS = BIT(15),
5029 WIPHY_FLAG_TDLS_EXTERNAL_SETUP = BIT(16),
5030 WIPHY_FLAG_HAVE_AP_SME = BIT(17),
5031 WIPHY_FLAG_REPORTS_OBSS = BIT(18),
5032 WIPHY_FLAG_AP_PROBE_RESP_OFFLOAD = BIT(19),
5033 WIPHY_FLAG_OFFCHAN_TX = BIT(20),
5034 WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL = BIT(21),
5035 WIPHY_FLAG_SUPPORTS_5_10_MHZ = BIT(22),
5036 WIPHY_FLAG_HAS_CHANNEL_SWITCH = BIT(23),
5037 WIPHY_FLAG_NOTIFY_REGDOM_BY_DRIVER = BIT(24),
5038 WIPHY_FLAG_CHANNEL_CHANGE_ON_BEACON = BIT(25),
5039};
5040
5041/**
5042 * struct ieee80211_iface_limit - limit on certain interface types
5043 * @max: maximum number of interfaces of these types
5044 * @types: interface types (bits)
5045 */
5046struct ieee80211_iface_limit {
5047 u16 max;
5048 u16 types;
5049};
5050
5051/**
5052 * struct ieee80211_iface_combination - possible interface combination
5053 *
5054 * With this structure the driver can describe which interface
5055 * combinations it supports concurrently. When set in a struct wiphy_radio,
5056 * the combinations refer to combinations of interfaces currently active on
5057 * that radio.
5058 *
5059 * Examples:
5060 *
5061 * 1. Allow #STA <= 1, #AP <= 1, matching BI, channels = 1, 2 total:
5062 *
5063 * .. code-block:: c
5064 *
5065 * struct ieee80211_iface_limit limits1[] = {
5066 * { .max = 1, .types = BIT(NL80211_IFTYPE_STATION), },
5067 * { .max = 1, .types = BIT(NL80211_IFTYPE_AP), },
5068 * };
5069 * struct ieee80211_iface_combination combination1 = {
5070 * .limits = limits1,
5071 * .n_limits = ARRAY_SIZE(limits1),
5072 * .max_interfaces = 2,
5073 * .beacon_int_infra_match = true,
5074 * };
5075 *
5076 *
5077 * 2. Allow #{AP, P2P-GO} <= 8, channels = 1, 8 total:
5078 *
5079 * .. code-block:: c
5080 *
5081 * struct ieee80211_iface_limit limits2[] = {
5082 * { .max = 8, .types = BIT(NL80211_IFTYPE_AP) |
5083 * BIT(NL80211_IFTYPE_P2P_GO), },
5084 * };
5085 * struct ieee80211_iface_combination combination2 = {
5086 * .limits = limits2,
5087 * .n_limits = ARRAY_SIZE(limits2),
5088 * .max_interfaces = 8,
5089 * .num_different_channels = 1,
5090 * };
5091 *
5092 *
5093 * 3. Allow #STA <= 1, #{P2P-client,P2P-GO} <= 3 on two channels, 4 total.
5094 *
5095 * This allows for an infrastructure connection and three P2P connections.
5096 *
5097 * .. code-block:: c
5098 *
5099 * struct ieee80211_iface_limit limits3[] = {
5100 * { .max = 1, .types = BIT(NL80211_IFTYPE_STATION), },
5101 * { .max = 3, .types = BIT(NL80211_IFTYPE_P2P_GO) |
5102 * BIT(NL80211_IFTYPE_P2P_CLIENT), },
5103 * };
5104 * struct ieee80211_iface_combination combination3 = {
5105 * .limits = limits3,
5106 * .n_limits = ARRAY_SIZE(limits3),
5107 * .max_interfaces = 4,
5108 * .num_different_channels = 2,
5109 * };
5110 *
5111 */
5112struct ieee80211_iface_combination {
5113 /**
5114 * @limits:
5115 * limits for the given interface types
5116 */
5117 const struct ieee80211_iface_limit *limits;
5118
5119 /**
5120 * @num_different_channels:
5121 * can use up to this many different channels
5122 */
5123 u32 num_different_channels;
5124
5125 /**
5126 * @max_interfaces:
5127 * maximum number of interfaces in total allowed in this group
5128 */
5129 u16 max_interfaces;
5130
5131 /**
5132 * @n_limits:
5133 * number of limitations
5134 */
5135 u8 n_limits;
5136
5137 /**
5138 * @beacon_int_infra_match:
5139 * In this combination, the beacon intervals between infrastructure
5140 * and AP types must match. This is required only in special cases.
5141 */
5142 bool beacon_int_infra_match;
5143
5144 /**
5145 * @radar_detect_widths:
5146 * bitmap of channel widths supported for radar detection
5147 */
5148 u8 radar_detect_widths;
5149
5150 /**
5151 * @radar_detect_regions:
5152 * bitmap of regions supported for radar detection
5153 */
5154 u8 radar_detect_regions;
5155
5156 /**
5157 * @beacon_int_min_gcd:
5158 * This interface combination supports different beacon intervals.
5159 *
5160 * = 0
5161 * all beacon intervals for different interface must be same.
5162 * > 0
5163 * any beacon interval for the interface part of this combination AND
5164 * GCD of all beacon intervals from beaconing interfaces of this
5165 * combination must be greater or equal to this value.
5166 */
5167 u32 beacon_int_min_gcd;
5168};
5169
5170struct ieee80211_txrx_stypes {
5171 u16 tx, rx;
5172};
5173
5174/**
5175 * enum wiphy_wowlan_support_flags - WoWLAN support flags
5176 * @WIPHY_WOWLAN_ANY: supports wakeup for the special "any"
5177 * trigger that keeps the device operating as-is and
5178 * wakes up the host on any activity, for example a
5179 * received packet that passed filtering; note that the
5180 * packet should be preserved in that case
5181 * @WIPHY_WOWLAN_MAGIC_PKT: supports wakeup on magic packet
5182 * (see nl80211.h)
5183 * @WIPHY_WOWLAN_DISCONNECT: supports wakeup on disconnect
5184 * @WIPHY_WOWLAN_SUPPORTS_GTK_REKEY: supports GTK rekeying while asleep
5185 * @WIPHY_WOWLAN_GTK_REKEY_FAILURE: supports wakeup on GTK rekey failure
5186 * @WIPHY_WOWLAN_EAP_IDENTITY_REQ: supports wakeup on EAP identity request
5187 * @WIPHY_WOWLAN_4WAY_HANDSHAKE: supports wakeup on 4-way handshake failure
5188 * @WIPHY_WOWLAN_RFKILL_RELEASE: supports wakeup on RF-kill release
5189 * @WIPHY_WOWLAN_NET_DETECT: supports wakeup on network detection
5190 */
5191enum wiphy_wowlan_support_flags {
5192 WIPHY_WOWLAN_ANY = BIT(0),
5193 WIPHY_WOWLAN_MAGIC_PKT = BIT(1),
5194 WIPHY_WOWLAN_DISCONNECT = BIT(2),
5195 WIPHY_WOWLAN_SUPPORTS_GTK_REKEY = BIT(3),
5196 WIPHY_WOWLAN_GTK_REKEY_FAILURE = BIT(4),
5197 WIPHY_WOWLAN_EAP_IDENTITY_REQ = BIT(5),
5198 WIPHY_WOWLAN_4WAY_HANDSHAKE = BIT(6),
5199 WIPHY_WOWLAN_RFKILL_RELEASE = BIT(7),
5200 WIPHY_WOWLAN_NET_DETECT = BIT(8),
5201};
5202
5203struct wiphy_wowlan_tcp_support {
5204 const struct nl80211_wowlan_tcp_data_token_feature *tok;
5205 u32 data_payload_max;
5206 u32 data_interval_max;
5207 u32 wake_payload_max;
5208 bool seq;
5209};
5210
5211/**
5212 * struct wiphy_wowlan_support - WoWLAN support data
5213 * @flags: see &enum wiphy_wowlan_support_flags
5214 * @n_patterns: number of supported wakeup patterns
5215 * (see nl80211.h for the pattern definition)
5216 * @pattern_max_len: maximum length of each pattern
5217 * @pattern_min_len: minimum length of each pattern
5218 * @max_pkt_offset: maximum Rx packet offset
5219 * @max_nd_match_sets: maximum number of matchsets for net-detect,
5220 * similar, but not necessarily identical, to max_match_sets for
5221 * scheduled scans.
5222 * See &struct cfg80211_sched_scan_request.@match_sets for more
5223 * details.
5224 * @tcp: TCP wakeup support information
5225 */
5226struct wiphy_wowlan_support {
5227 u32 flags;
5228 int n_patterns;
5229 int pattern_max_len;
5230 int pattern_min_len;
5231 int max_pkt_offset;
5232 int max_nd_match_sets;
5233 const struct wiphy_wowlan_tcp_support *tcp;
5234};
5235
5236/**
5237 * struct wiphy_coalesce_support - coalesce support data
5238 * @n_rules: maximum number of coalesce rules
5239 * @max_delay: maximum supported coalescing delay in msecs
5240 * @n_patterns: number of supported patterns in a rule
5241 * (see nl80211.h for the pattern definition)
5242 * @pattern_max_len: maximum length of each pattern
5243 * @pattern_min_len: minimum length of each pattern
5244 * @max_pkt_offset: maximum Rx packet offset
5245 */
5246struct wiphy_coalesce_support {
5247 int n_rules;
5248 int max_delay;
5249 int n_patterns;
5250 int pattern_max_len;
5251 int pattern_min_len;
5252 int max_pkt_offset;
5253};
5254
5255/**
5256 * enum wiphy_vendor_command_flags - validation flags for vendor commands
5257 * @WIPHY_VENDOR_CMD_NEED_WDEV: vendor command requires wdev
5258 * @WIPHY_VENDOR_CMD_NEED_NETDEV: vendor command requires netdev
5259 * @WIPHY_VENDOR_CMD_NEED_RUNNING: interface/wdev must be up & running
5260 * (must be combined with %_WDEV or %_NETDEV)
5261 */
5262enum wiphy_vendor_command_flags {
5263 WIPHY_VENDOR_CMD_NEED_WDEV = BIT(0),
5264 WIPHY_VENDOR_CMD_NEED_NETDEV = BIT(1),
5265 WIPHY_VENDOR_CMD_NEED_RUNNING = BIT(2),
5266};
5267
5268/**
5269 * enum wiphy_opmode_flag - Station's ht/vht operation mode information flags
5270 *
5271 * @STA_OPMODE_MAX_BW_CHANGED: Max Bandwidth changed
5272 * @STA_OPMODE_SMPS_MODE_CHANGED: SMPS mode changed
5273 * @STA_OPMODE_N_SS_CHANGED: max N_SS (number of spatial streams) changed
5274 *
5275 */
5276enum wiphy_opmode_flag {
5277 STA_OPMODE_MAX_BW_CHANGED = BIT(0),
5278 STA_OPMODE_SMPS_MODE_CHANGED = BIT(1),
5279 STA_OPMODE_N_SS_CHANGED = BIT(2),
5280};
5281
5282/**
5283 * struct sta_opmode_info - Station's ht/vht operation mode information
5284 * @changed: contains value from &enum wiphy_opmode_flag
5285 * @smps_mode: New SMPS mode value from &enum nl80211_smps_mode of a station
5286 * @bw: new max bandwidth value from &enum nl80211_chan_width of a station
5287 * @rx_nss: new rx_nss value of a station
5288 */
5289
5290struct sta_opmode_info {
5291 u32 changed;
5292 enum nl80211_smps_mode smps_mode;
5293 enum nl80211_chan_width bw;
5294 u8 rx_nss;
5295};
5296
5297#define VENDOR_CMD_RAW_DATA ((const struct nla_policy *)(long)(-ENODATA))
5298
5299/**
5300 * struct wiphy_vendor_command - vendor command definition
5301 * @info: vendor command identifying information, as used in nl80211
5302 * @flags: flags, see &enum wiphy_vendor_command_flags
5303 * @doit: callback for the operation, note that wdev is %NULL if the
5304 * flags didn't ask for a wdev and non-%NULL otherwise; the data
5305 * pointer may be %NULL if userspace provided no data at all
5306 * @dumpit: dump callback, for transferring bigger/multiple items. The
5307 * @storage points to cb->args[5], ie. is preserved over the multiple
5308 * dumpit calls.
5309 * @policy: policy pointer for attributes within %NL80211_ATTR_VENDOR_DATA.
5310 * Set this to %VENDOR_CMD_RAW_DATA if no policy can be given and the
5311 * attribute is just raw data (e.g. a firmware command).
5312 * @maxattr: highest attribute number in policy
5313 * It's recommended to not have the same sub command with both @doit and
5314 * @dumpit, so that userspace can assume certain ones are get and others
5315 * are used with dump requests.
5316 */
5317struct wiphy_vendor_command {
5318 struct nl80211_vendor_cmd_info info;
5319 u32 flags;
5320 int (*doit)(struct wiphy *wiphy, struct wireless_dev *wdev,
5321 const void *data, int data_len);
5322 int (*dumpit)(struct wiphy *wiphy, struct wireless_dev *wdev,
5323 struct sk_buff *skb, const void *data, int data_len,
5324 unsigned long *storage);
5325 const struct nla_policy *policy;
5326 unsigned int maxattr;
5327};
5328
5329/**
5330 * struct wiphy_iftype_ext_capab - extended capabilities per interface type
5331 * @iftype: interface type
5332 * @extended_capabilities: extended capabilities supported by the driver,
5333 * additional capabilities might be supported by userspace; these are the
5334 * 802.11 extended capabilities ("Extended Capabilities element") and are
5335 * in the same format as in the information element. See IEEE Std
5336 * 802.11-2012 8.4.2.29 for the defined fields.
5337 * @extended_capabilities_mask: mask of the valid values
5338 * @extended_capabilities_len: length of the extended capabilities
5339 * @eml_capabilities: EML capabilities (for MLO)
5340 * @mld_capa_and_ops: MLD capabilities and operations (for MLO)
5341 */
5342struct wiphy_iftype_ext_capab {
5343 enum nl80211_iftype iftype;
5344 const u8 *extended_capabilities;
5345 const u8 *extended_capabilities_mask;
5346 u8 extended_capabilities_len;
5347 u16 eml_capabilities;
5348 u16 mld_capa_and_ops;
5349};
5350
5351/**
5352 * cfg80211_get_iftype_ext_capa - lookup interface type extended capability
5353 * @wiphy: the wiphy to look up from
5354 * @type: the interface type to look up
5355 *
5356 * Return: The extended capability for the given interface @type, may be %NULL
5357 */
5358const struct wiphy_iftype_ext_capab *
5359cfg80211_get_iftype_ext_capa(struct wiphy *wiphy, enum nl80211_iftype type);
5360
5361/**
5362 * struct cfg80211_pmsr_capabilities - cfg80211 peer measurement capabilities
5363 * @max_peers: maximum number of peers in a single measurement
5364 * @report_ap_tsf: can report assoc AP's TSF for radio resource measurement
5365 * @randomize_mac_addr: can randomize MAC address for measurement
5366 * @ftm: FTM measurement data
5367 * @ftm.supported: FTM measurement is supported
5368 * @ftm.asap: ASAP-mode is supported
5369 * @ftm.non_asap: non-ASAP-mode is supported
5370 * @ftm.request_lci: can request LCI data
5371 * @ftm.request_civicloc: can request civic location data
5372 * @ftm.preambles: bitmap of preambles supported (&enum nl80211_preamble)
5373 * @ftm.bandwidths: bitmap of bandwidths supported (&enum nl80211_chan_width)
5374 * @ftm.max_bursts_exponent: maximum burst exponent supported
5375 * (set to -1 if not limited; note that setting this will necessarily
5376 * forbid using the value 15 to let the responder pick)
5377 * @ftm.max_ftms_per_burst: maximum FTMs per burst supported (set to 0 if
5378 * not limited)
5379 * @ftm.trigger_based: trigger based ranging measurement is supported
5380 * @ftm.non_trigger_based: non trigger based ranging measurement is supported
5381 */
5382struct cfg80211_pmsr_capabilities {
5383 unsigned int max_peers;
5384 u8 report_ap_tsf:1,
5385 randomize_mac_addr:1;
5386
5387 struct {
5388 u32 preambles;
5389 u32 bandwidths;
5390 s8 max_bursts_exponent;
5391 u8 max_ftms_per_burst;
5392 u8 supported:1,
5393 asap:1,
5394 non_asap:1,
5395 request_lci:1,
5396 request_civicloc:1,
5397 trigger_based:1,
5398 non_trigger_based:1;
5399 } ftm;
5400};
5401
5402/**
5403 * struct wiphy_iftype_akm_suites - This structure encapsulates supported akm
5404 * suites for interface types defined in @iftypes_mask. Each type in the
5405 * @iftypes_mask must be unique across all instances of iftype_akm_suites.
5406 *
5407 * @iftypes_mask: bitmask of interfaces types
5408 * @akm_suites: points to an array of supported akm suites
5409 * @n_akm_suites: number of supported AKM suites
5410 */
5411struct wiphy_iftype_akm_suites {
5412 u16 iftypes_mask;
5413 const u32 *akm_suites;
5414 int n_akm_suites;
5415};
5416
5417/**
5418 * struct wiphy_radio_freq_range - wiphy frequency range
5419 * @start_freq: start range edge frequency (kHz)
5420 * @end_freq: end range edge frequency (kHz)
5421 */
5422struct wiphy_radio_freq_range {
5423 u32 start_freq;
5424 u32 end_freq;
5425};
5426
5427
5428/**
5429 * struct wiphy_radio - physical radio of a wiphy
5430 * This structure describes a physical radio belonging to a wiphy.
5431 * It is used to describe concurrent-channel capabilities. Only one channel
5432 * can be active on the radio described by struct wiphy_radio.
5433 *
5434 * @freq_range: frequency range that the radio can operate on.
5435 * @n_freq_range: number of elements in @freq_range
5436 *
5437 * @iface_combinations: Valid interface combinations array, should not
5438 * list single interface types.
5439 * @n_iface_combinations: number of entries in @iface_combinations array.
5440 *
5441 * @antenna_mask: bitmask of antennas connected to this radio.
5442 */
5443struct wiphy_radio {
5444 const struct wiphy_radio_freq_range *freq_range;
5445 int n_freq_range;
5446
5447 const struct ieee80211_iface_combination *iface_combinations;
5448 int n_iface_combinations;
5449
5450 u32 antenna_mask;
5451};
5452
5453#define CFG80211_HW_TIMESTAMP_ALL_PEERS 0xffff
5454
5455/**
5456 * struct wiphy - wireless hardware description
5457 * @mtx: mutex for the data (structures) of this device
5458 * @reg_notifier: the driver's regulatory notification callback,
5459 * note that if your driver uses wiphy_apply_custom_regulatory()
5460 * the reg_notifier's request can be passed as NULL
5461 * @regd: the driver's regulatory domain, if one was requested via
5462 * the regulatory_hint() API. This can be used by the driver
5463 * on the reg_notifier() if it chooses to ignore future
5464 * regulatory domain changes caused by other drivers.
5465 * @signal_type: signal type reported in &struct cfg80211_bss.
5466 * @cipher_suites: supported cipher suites
5467 * @n_cipher_suites: number of supported cipher suites
5468 * @akm_suites: supported AKM suites. These are the default AKMs supported if
5469 * the supported AKMs not advertized for a specific interface type in
5470 * iftype_akm_suites.
5471 * @n_akm_suites: number of supported AKM suites
5472 * @iftype_akm_suites: array of supported akm suites info per interface type.
5473 * Note that the bits in @iftypes_mask inside this structure cannot
5474 * overlap (i.e. only one occurrence of each type is allowed across all
5475 * instances of iftype_akm_suites).
5476 * @num_iftype_akm_suites: number of interface types for which supported akm
5477 * suites are specified separately.
5478 * @retry_short: Retry limit for short frames (dot11ShortRetryLimit)
5479 * @retry_long: Retry limit for long frames (dot11LongRetryLimit)
5480 * @frag_threshold: Fragmentation threshold (dot11FragmentationThreshold);
5481 * -1 = fragmentation disabled, only odd values >= 256 used
5482 * @rts_threshold: RTS threshold (dot11RTSThreshold); -1 = RTS/CTS disabled
5483 * @_net: the network namespace this wiphy currently lives in
5484 * @perm_addr: permanent MAC address of this device
5485 * @addr_mask: If the device supports multiple MAC addresses by masking,
5486 * set this to a mask with variable bits set to 1, e.g. if the last
5487 * four bits are variable then set it to 00-00-00-00-00-0f. The actual
5488 * variable bits shall be determined by the interfaces added, with
5489 * interfaces not matching the mask being rejected to be brought up.
5490 * @n_addresses: number of addresses in @addresses.
5491 * @addresses: If the device has more than one address, set this pointer
5492 * to a list of addresses (6 bytes each). The first one will be used
5493 * by default for perm_addr. In this case, the mask should be set to
5494 * all-zeroes. In this case it is assumed that the device can handle
5495 * the same number of arbitrary MAC addresses.
5496 * @registered: protects ->resume and ->suspend sysfs callbacks against
5497 * unregister hardware
5498 * @debugfsdir: debugfs directory used for this wiphy (ieee80211/<wiphyname>).
5499 * It will be renamed automatically on wiphy renames
5500 * @dev: (virtual) struct device for this wiphy. The item in
5501 * /sys/class/ieee80211/ points to this. You need use set_wiphy_dev()
5502 * (see below).
5503 * @wext: wireless extension handlers
5504 * @priv: driver private data (sized according to wiphy_new() parameter)
5505 * @interface_modes: bitmask of interfaces types valid for this wiphy,
5506 * must be set by driver
5507 * @iface_combinations: Valid interface combinations array, should not
5508 * list single interface types.
5509 * @n_iface_combinations: number of entries in @iface_combinations array.
5510 * @software_iftypes: bitmask of software interface types, these are not
5511 * subject to any restrictions since they are purely managed in SW.
5512 * @flags: wiphy flags, see &enum wiphy_flags
5513 * @regulatory_flags: wiphy regulatory flags, see
5514 * &enum ieee80211_regulatory_flags
5515 * @features: features advertised to nl80211, see &enum nl80211_feature_flags.
5516 * @ext_features: extended features advertised to nl80211, see
5517 * &enum nl80211_ext_feature_index.
5518 * @bss_priv_size: each BSS struct has private data allocated with it,
5519 * this variable determines its size
5520 * @max_scan_ssids: maximum number of SSIDs the device can scan for in
5521 * any given scan
5522 * @max_sched_scan_reqs: maximum number of scheduled scan requests that
5523 * the device can run concurrently.
5524 * @max_sched_scan_ssids: maximum number of SSIDs the device can scan
5525 * for in any given scheduled scan
5526 * @max_match_sets: maximum number of match sets the device can handle
5527 * when performing a scheduled scan, 0 if filtering is not
5528 * supported.
5529 * @max_scan_ie_len: maximum length of user-controlled IEs device can
5530 * add to probe request frames transmitted during a scan, must not
5531 * include fixed IEs like supported rates
5532 * @max_sched_scan_ie_len: same as max_scan_ie_len, but for scheduled
5533 * scans
5534 * @max_sched_scan_plans: maximum number of scan plans (scan interval and number
5535 * of iterations) for scheduled scan supported by the device.
5536 * @max_sched_scan_plan_interval: maximum interval (in seconds) for a
5537 * single scan plan supported by the device.
5538 * @max_sched_scan_plan_iterations: maximum number of iterations for a single
5539 * scan plan supported by the device.
5540 * @coverage_class: current coverage class
5541 * @fw_version: firmware version for ethtool reporting
5542 * @hw_version: hardware version for ethtool reporting
5543 * @max_num_pmkids: maximum number of PMKIDs supported by device
5544 * @privid: a pointer that drivers can use to identify if an arbitrary
5545 * wiphy is theirs, e.g. in global notifiers
5546 * @bands: information about bands/channels supported by this device
5547 *
5548 * @mgmt_stypes: bitmasks of frame subtypes that can be subscribed to or
5549 * transmitted through nl80211, points to an array indexed by interface
5550 * type
5551 *
5552 * @available_antennas_tx: bitmap of antennas which are available to be
5553 * configured as TX antennas. Antenna configuration commands will be
5554 * rejected unless this or @available_antennas_rx is set.
5555 *
5556 * @available_antennas_rx: bitmap of antennas which are available to be
5557 * configured as RX antennas. Antenna configuration commands will be
5558 * rejected unless this or @available_antennas_tx is set.
5559 *
5560 * @probe_resp_offload:
5561 * Bitmap of supported protocols for probe response offloading.
5562 * See &enum nl80211_probe_resp_offload_support_attr. Only valid
5563 * when the wiphy flag @WIPHY_FLAG_AP_PROBE_RESP_OFFLOAD is set.
5564 *
5565 * @max_remain_on_channel_duration: Maximum time a remain-on-channel operation
5566 * may request, if implemented.
5567 *
5568 * @wowlan: WoWLAN support information
5569 * @wowlan_config: current WoWLAN configuration; this should usually not be
5570 * used since access to it is necessarily racy, use the parameter passed
5571 * to the suspend() operation instead.
5572 *
5573 * @ap_sme_capa: AP SME capabilities, flags from &enum nl80211_ap_sme_features.
5574 * @ht_capa_mod_mask: Specify what ht_cap values can be over-ridden.
5575 * If null, then none can be over-ridden.
5576 * @vht_capa_mod_mask: Specify what VHT capabilities can be over-ridden.
5577 * If null, then none can be over-ridden.
5578 *
5579 * @wdev_list: the list of associated (virtual) interfaces; this list must
5580 * not be modified by the driver, but can be read with RTNL/RCU protection.
5581 *
5582 * @max_acl_mac_addrs: Maximum number of MAC addresses that the device
5583 * supports for ACL.
5584 *
5585 * @extended_capabilities: extended capabilities supported by the driver,
5586 * additional capabilities might be supported by userspace; these are
5587 * the 802.11 extended capabilities ("Extended Capabilities element")
5588 * and are in the same format as in the information element. See
5589 * 802.11-2012 8.4.2.29 for the defined fields. These are the default
5590 * extended capabilities to be used if the capabilities are not specified
5591 * for a specific interface type in iftype_ext_capab.
5592 * @extended_capabilities_mask: mask of the valid values
5593 * @extended_capabilities_len: length of the extended capabilities
5594 * @iftype_ext_capab: array of extended capabilities per interface type
5595 * @num_iftype_ext_capab: number of interface types for which extended
5596 * capabilities are specified separately.
5597 * @coalesce: packet coalescing support information
5598 *
5599 * @vendor_commands: array of vendor commands supported by the hardware
5600 * @n_vendor_commands: number of vendor commands
5601 * @vendor_events: array of vendor events supported by the hardware
5602 * @n_vendor_events: number of vendor events
5603 *
5604 * @max_ap_assoc_sta: maximum number of associated stations supported in AP mode
5605 * (including P2P GO) or 0 to indicate no such limit is advertised. The
5606 * driver is allowed to advertise a theoretical limit that it can reach in
5607 * some cases, but may not always reach.
5608 *
5609 * @max_num_csa_counters: Number of supported csa_counters in beacons
5610 * and probe responses. This value should be set if the driver
5611 * wishes to limit the number of csa counters. Default (0) means
5612 * infinite.
5613 * @bss_select_support: bitmask indicating the BSS selection criteria supported
5614 * by the driver in the .connect() callback. The bit position maps to the
5615 * attribute indices defined in &enum nl80211_bss_select_attr.
5616 *
5617 * @nan_supported_bands: bands supported by the device in NAN mode, a
5618 * bitmap of &enum nl80211_band values. For instance, for
5619 * NL80211_BAND_2GHZ, bit 0 would be set
5620 * (i.e. BIT(NL80211_BAND_2GHZ)).
5621 *
5622 * @txq_limit: configuration of internal TX queue frame limit
5623 * @txq_memory_limit: configuration internal TX queue memory limit
5624 * @txq_quantum: configuration of internal TX queue scheduler quantum
5625 *
5626 * @tx_queue_len: allow setting transmit queue len for drivers not using
5627 * wake_tx_queue
5628 *
5629 * @support_mbssid: can HW support association with nontransmitted AP
5630 * @support_only_he_mbssid: don't parse MBSSID elements if it is not
5631 * HE AP, in order to avoid compatibility issues.
5632 * @support_mbssid must be set for this to have any effect.
5633 *
5634 * @pmsr_capa: peer measurement capabilities
5635 *
5636 * @tid_config_support: describes the per-TID config support that the
5637 * device has
5638 * @tid_config_support.vif: bitmap of attributes (configurations)
5639 * supported by the driver for each vif
5640 * @tid_config_support.peer: bitmap of attributes (configurations)
5641 * supported by the driver for each peer
5642 * @tid_config_support.max_retry: maximum supported retry count for
5643 * long/short retry configuration
5644 *
5645 * @max_data_retry_count: maximum supported per TID retry count for
5646 * configuration through the %NL80211_TID_CONFIG_ATTR_RETRY_SHORT and
5647 * %NL80211_TID_CONFIG_ATTR_RETRY_LONG attributes
5648 * @sar_capa: SAR control capabilities
5649 * @rfkill: a pointer to the rfkill structure
5650 *
5651 * @mbssid_max_interfaces: maximum number of interfaces supported by the driver
5652 * in a multiple BSSID set. This field must be set to a non-zero value
5653 * by the driver to advertise MBSSID support.
5654 * @ema_max_profile_periodicity: maximum profile periodicity supported by
5655 * the driver. Setting this field to a non-zero value indicates that the
5656 * driver supports enhanced multi-BSSID advertisements (EMA AP).
5657 * @max_num_akm_suites: maximum number of AKM suites allowed for
5658 * configuration through %NL80211_CMD_CONNECT, %NL80211_CMD_ASSOCIATE and
5659 * %NL80211_CMD_START_AP. Set to NL80211_MAX_NR_AKM_SUITES if not set by
5660 * driver. If set by driver minimum allowed value is
5661 * NL80211_MAX_NR_AKM_SUITES in order to avoid compatibility issues with
5662 * legacy userspace and maximum allowed value is
5663 * CFG80211_MAX_NUM_AKM_SUITES.
5664 *
5665 * @hw_timestamp_max_peers: maximum number of peers that the driver supports
5666 * enabling HW timestamping for concurrently. Setting this field to a
5667 * non-zero value indicates that the driver supports HW timestamping.
5668 * A value of %CFG80211_HW_TIMESTAMP_ALL_PEERS indicates the driver
5669 * supports enabling HW timestamping for all peers (i.e. no need to
5670 * specify a mac address).
5671 *
5672 * @radio: radios belonging to this wiphy
5673 * @n_radio: number of radios
5674 */
5675struct wiphy {
5676 struct mutex mtx;
5677
5678 /* assign these fields before you register the wiphy */
5679
5680 u8 perm_addr[ETH_ALEN];
5681 u8 addr_mask[ETH_ALEN];
5682
5683 struct mac_address *addresses;
5684
5685 const struct ieee80211_txrx_stypes *mgmt_stypes;
5686
5687 const struct ieee80211_iface_combination *iface_combinations;
5688 int n_iface_combinations;
5689 u16 software_iftypes;
5690
5691 u16 n_addresses;
5692
5693 /* Supported interface modes, OR together BIT(NL80211_IFTYPE_...) */
5694 u16 interface_modes;
5695
5696 u16 max_acl_mac_addrs;
5697
5698 u32 flags, regulatory_flags, features;
5699 u8 ext_features[DIV_ROUND_UP(NUM_NL80211_EXT_FEATURES, 8)];
5700
5701 u32 ap_sme_capa;
5702
5703 enum cfg80211_signal_type signal_type;
5704
5705 int bss_priv_size;
5706 u8 max_scan_ssids;
5707 u8 max_sched_scan_reqs;
5708 u8 max_sched_scan_ssids;
5709 u8 max_match_sets;
5710 u16 max_scan_ie_len;
5711 u16 max_sched_scan_ie_len;
5712 u32 max_sched_scan_plans;
5713 u32 max_sched_scan_plan_interval;
5714 u32 max_sched_scan_plan_iterations;
5715
5716 int n_cipher_suites;
5717 const u32 *cipher_suites;
5718
5719 int n_akm_suites;
5720 const u32 *akm_suites;
5721
5722 const struct wiphy_iftype_akm_suites *iftype_akm_suites;
5723 unsigned int num_iftype_akm_suites;
5724
5725 u8 retry_short;
5726 u8 retry_long;
5727 u32 frag_threshold;
5728 u32 rts_threshold;
5729 u8 coverage_class;
5730
5731 char fw_version[ETHTOOL_FWVERS_LEN];
5732 u32 hw_version;
5733
5734#ifdef CONFIG_PM
5735 const struct wiphy_wowlan_support *wowlan;
5736 struct cfg80211_wowlan *wowlan_config;
5737#endif
5738
5739 u16 max_remain_on_channel_duration;
5740
5741 u8 max_num_pmkids;
5742
5743 u32 available_antennas_tx;
5744 u32 available_antennas_rx;
5745
5746 u32 probe_resp_offload;
5747
5748 const u8 *extended_capabilities, *extended_capabilities_mask;
5749 u8 extended_capabilities_len;
5750
5751 const struct wiphy_iftype_ext_capab *iftype_ext_capab;
5752 unsigned int num_iftype_ext_capab;
5753
5754 const void *privid;
5755
5756 struct ieee80211_supported_band *bands[NUM_NL80211_BANDS];
5757
5758 void (*reg_notifier)(struct wiphy *wiphy,
5759 struct regulatory_request *request);
5760
5761 /* fields below are read-only, assigned by cfg80211 */
5762
5763 const struct ieee80211_regdomain __rcu *regd;
5764
5765 struct device dev;
5766
5767 bool registered;
5768
5769 struct dentry *debugfsdir;
5770
5771 const struct ieee80211_ht_cap *ht_capa_mod_mask;
5772 const struct ieee80211_vht_cap *vht_capa_mod_mask;
5773
5774 struct list_head wdev_list;
5775
5776 possible_net_t _net;
5777
5778#ifdef CONFIG_CFG80211_WEXT
5779 const struct iw_handler_def *wext;
5780#endif
5781
5782 const struct wiphy_coalesce_support *coalesce;
5783
5784 const struct wiphy_vendor_command *vendor_commands;
5785 const struct nl80211_vendor_cmd_info *vendor_events;
5786 int n_vendor_commands, n_vendor_events;
5787
5788 u16 max_ap_assoc_sta;
5789
5790 u8 max_num_csa_counters;
5791
5792 u32 bss_select_support;
5793
5794 u8 nan_supported_bands;
5795
5796 u32 txq_limit;
5797 u32 txq_memory_limit;
5798 u32 txq_quantum;
5799
5800 unsigned long tx_queue_len;
5801
5802 u8 support_mbssid:1,
5803 support_only_he_mbssid:1;
5804
5805 const struct cfg80211_pmsr_capabilities *pmsr_capa;
5806
5807 struct {
5808 u64 peer, vif;
5809 u8 max_retry;
5810 } tid_config_support;
5811
5812 u8 max_data_retry_count;
5813
5814 const struct cfg80211_sar_capa *sar_capa;
5815
5816 struct rfkill *rfkill;
5817
5818 u8 mbssid_max_interfaces;
5819 u8 ema_max_profile_periodicity;
5820 u16 max_num_akm_suites;
5821
5822 u16 hw_timestamp_max_peers;
5823
5824 int n_radio;
5825 const struct wiphy_radio *radio;
5826
5827 char priv[] __aligned(NETDEV_ALIGN);
5828};
5829
5830static inline struct net *wiphy_net(struct wiphy *wiphy)
5831{
5832 return read_pnet(&wiphy->_net);
5833}
5834
5835static inline void wiphy_net_set(struct wiphy *wiphy, struct net *net)
5836{
5837 write_pnet(&wiphy->_net, net);
5838}
5839
5840/**
5841 * wiphy_priv - return priv from wiphy
5842 *
5843 * @wiphy: the wiphy whose priv pointer to return
5844 * Return: The priv of @wiphy.
5845 */
5846static inline void *wiphy_priv(struct wiphy *wiphy)
5847{
5848 BUG_ON(!wiphy);
5849 return &wiphy->priv;
5850}
5851
5852/**
5853 * priv_to_wiphy - return the wiphy containing the priv
5854 *
5855 * @priv: a pointer previously returned by wiphy_priv
5856 * Return: The wiphy of @priv.
5857 */
5858static inline struct wiphy *priv_to_wiphy(void *priv)
5859{
5860 BUG_ON(!priv);
5861 return container_of(priv, struct wiphy, priv);
5862}
5863
5864/**
5865 * set_wiphy_dev - set device pointer for wiphy
5866 *
5867 * @wiphy: The wiphy whose device to bind
5868 * @dev: The device to parent it to
5869 */
5870static inline void set_wiphy_dev(struct wiphy *wiphy, struct device *dev)
5871{
5872 wiphy->dev.parent = dev;
5873}
5874
5875/**
5876 * wiphy_dev - get wiphy dev pointer
5877 *
5878 * @wiphy: The wiphy whose device struct to look up
5879 * Return: The dev of @wiphy.
5880 */
5881static inline struct device *wiphy_dev(struct wiphy *wiphy)
5882{
5883 return wiphy->dev.parent;
5884}
5885
5886/**
5887 * wiphy_name - get wiphy name
5888 *
5889 * @wiphy: The wiphy whose name to return
5890 * Return: The name of @wiphy.
5891 */
5892static inline const char *wiphy_name(const struct wiphy *wiphy)
5893{
5894 return dev_name(&wiphy->dev);
5895}
5896
5897/**
5898 * wiphy_new_nm - create a new wiphy for use with cfg80211
5899 *
5900 * @ops: The configuration operations for this device
5901 * @sizeof_priv: The size of the private area to allocate
5902 * @requested_name: Request a particular name.
5903 * NULL is valid value, and means use the default phy%d naming.
5904 *
5905 * Create a new wiphy and associate the given operations with it.
5906 * @sizeof_priv bytes are allocated for private use.
5907 *
5908 * Return: A pointer to the new wiphy. This pointer must be
5909 * assigned to each netdev's ieee80211_ptr for proper operation.
5910 */
5911struct wiphy *wiphy_new_nm(const struct cfg80211_ops *ops, int sizeof_priv,
5912 const char *requested_name);
5913
5914/**
5915 * wiphy_new - create a new wiphy for use with cfg80211
5916 *
5917 * @ops: The configuration operations for this device
5918 * @sizeof_priv: The size of the private area to allocate
5919 *
5920 * Create a new wiphy and associate the given operations with it.
5921 * @sizeof_priv bytes are allocated for private use.
5922 *
5923 * Return: A pointer to the new wiphy. This pointer must be
5924 * assigned to each netdev's ieee80211_ptr for proper operation.
5925 */
5926static inline struct wiphy *wiphy_new(const struct cfg80211_ops *ops,
5927 int sizeof_priv)
5928{
5929 return wiphy_new_nm(ops, sizeof_priv, NULL);
5930}
5931
5932/**
5933 * wiphy_register - register a wiphy with cfg80211
5934 *
5935 * @wiphy: The wiphy to register.
5936 *
5937 * Return: A non-negative wiphy index or a negative error code.
5938 */
5939int wiphy_register(struct wiphy *wiphy);
5940
5941/* this is a define for better error reporting (file/line) */
5942#define lockdep_assert_wiphy(wiphy) lockdep_assert_held(&(wiphy)->mtx)
5943
5944/**
5945 * rcu_dereference_wiphy - rcu_dereference with debug checking
5946 * @wiphy: the wiphy to check the locking on
5947 * @p: The pointer to read, prior to dereferencing
5948 *
5949 * Do an rcu_dereference(p), but check caller either holds rcu_read_lock()
5950 * or RTNL. Note: Please prefer wiphy_dereference() or rcu_dereference().
5951 */
5952#define rcu_dereference_wiphy(wiphy, p) \
5953 rcu_dereference_check(p, lockdep_is_held(&wiphy->mtx))
5954
5955/**
5956 * wiphy_dereference - fetch RCU pointer when updates are prevented by wiphy mtx
5957 * @wiphy: the wiphy to check the locking on
5958 * @p: The pointer to read, prior to dereferencing
5959 *
5960 * Return the value of the specified RCU-protected pointer, but omit the
5961 * READ_ONCE(), because caller holds the wiphy mutex used for updates.
5962 */
5963#define wiphy_dereference(wiphy, p) \
5964 rcu_dereference_protected(p, lockdep_is_held(&wiphy->mtx))
5965
5966/**
5967 * get_wiphy_regdom - get custom regdomain for the given wiphy
5968 * @wiphy: the wiphy to get the regdomain from
5969 *
5970 * Context: Requires any of RTNL, wiphy mutex or RCU protection.
5971 *
5972 * Return: pointer to the regulatory domain associated with the wiphy
5973 */
5974const struct ieee80211_regdomain *get_wiphy_regdom(struct wiphy *wiphy);
5975
5976/**
5977 * wiphy_unregister - deregister a wiphy from cfg80211
5978 *
5979 * @wiphy: The wiphy to unregister.
5980 *
5981 * After this call, no more requests can be made with this priv
5982 * pointer, but the call may sleep to wait for an outstanding
5983 * request that is being handled.
5984 */
5985void wiphy_unregister(struct wiphy *wiphy);
5986
5987/**
5988 * wiphy_free - free wiphy
5989 *
5990 * @wiphy: The wiphy to free
5991 */
5992void wiphy_free(struct wiphy *wiphy);
5993
5994/* internal structs */
5995struct cfg80211_conn;
5996struct cfg80211_internal_bss;
5997struct cfg80211_cached_keys;
5998struct cfg80211_cqm_config;
5999
6000/**
6001 * wiphy_lock - lock the wiphy
6002 * @wiphy: the wiphy to lock
6003 *
6004 * This is needed around registering and unregistering netdevs that
6005 * aren't created through cfg80211 calls, since that requires locking
6006 * in cfg80211 when the notifiers is called, but that cannot
6007 * differentiate which way it's called.
6008 *
6009 * It can also be used by drivers for their own purposes.
6010 *
6011 * When cfg80211 ops are called, the wiphy is already locked.
6012 *
6013 * Note that this makes sure that no workers that have been queued
6014 * with wiphy_queue_work() are running.
6015 */
6016static inline void wiphy_lock(struct wiphy *wiphy)
6017 __acquires(&wiphy->mtx)
6018{
6019 mutex_lock(&wiphy->mtx);
6020 __acquire(&wiphy->mtx);
6021}
6022
6023/**
6024 * wiphy_unlock - unlock the wiphy again
6025 * @wiphy: the wiphy to unlock
6026 */
6027static inline void wiphy_unlock(struct wiphy *wiphy)
6028 __releases(&wiphy->mtx)
6029{
6030 __release(&wiphy->mtx);
6031 mutex_unlock(&wiphy->mtx);
6032}
6033
6034struct wiphy_work;
6035typedef void (*wiphy_work_func_t)(struct wiphy *, struct wiphy_work *);
6036
6037struct wiphy_work {
6038 struct list_head entry;
6039 wiphy_work_func_t func;
6040};
6041
6042static inline void wiphy_work_init(struct wiphy_work *work,
6043 wiphy_work_func_t func)
6044{
6045 INIT_LIST_HEAD(&work->entry);
6046 work->func = func;
6047}
6048
6049/**
6050 * wiphy_work_queue - queue work for the wiphy
6051 * @wiphy: the wiphy to queue for
6052 * @work: the work item
6053 *
6054 * This is useful for work that must be done asynchronously, and work
6055 * queued here has the special property that the wiphy mutex will be
6056 * held as if wiphy_lock() was called, and that it cannot be running
6057 * after wiphy_lock() was called. Therefore, wiphy_cancel_work() can
6058 * use just cancel_work() instead of cancel_work_sync(), it requires
6059 * being in a section protected by wiphy_lock().
6060 */
6061void wiphy_work_queue(struct wiphy *wiphy, struct wiphy_work *work);
6062
6063/**
6064 * wiphy_work_cancel - cancel previously queued work
6065 * @wiphy: the wiphy, for debug purposes
6066 * @work: the work to cancel
6067 *
6068 * Cancel the work *without* waiting for it, this assumes being
6069 * called under the wiphy mutex acquired by wiphy_lock().
6070 */
6071void wiphy_work_cancel(struct wiphy *wiphy, struct wiphy_work *work);
6072
6073/**
6074 * wiphy_work_flush - flush previously queued work
6075 * @wiphy: the wiphy, for debug purposes
6076 * @work: the work to flush, this can be %NULL to flush all work
6077 *
6078 * Flush the work (i.e. run it if pending). This must be called
6079 * under the wiphy mutex acquired by wiphy_lock().
6080 */
6081void wiphy_work_flush(struct wiphy *wiphy, struct wiphy_work *work);
6082
6083struct wiphy_delayed_work {
6084 struct wiphy_work work;
6085 struct wiphy *wiphy;
6086 struct timer_list timer;
6087};
6088
6089void wiphy_delayed_work_timer(struct timer_list *t);
6090
6091static inline void wiphy_delayed_work_init(struct wiphy_delayed_work *dwork,
6092 wiphy_work_func_t func)
6093{
6094 timer_setup(&dwork->timer, wiphy_delayed_work_timer, 0);
6095 wiphy_work_init(&dwork->work, func);
6096}
6097
6098/**
6099 * wiphy_delayed_work_queue - queue delayed work for the wiphy
6100 * @wiphy: the wiphy to queue for
6101 * @dwork: the delayable worker
6102 * @delay: number of jiffies to wait before queueing
6103 *
6104 * This is useful for work that must be done asynchronously, and work
6105 * queued here has the special property that the wiphy mutex will be
6106 * held as if wiphy_lock() was called, and that it cannot be running
6107 * after wiphy_lock() was called. Therefore, wiphy_cancel_work() can
6108 * use just cancel_work() instead of cancel_work_sync(), it requires
6109 * being in a section protected by wiphy_lock().
6110 */
6111void wiphy_delayed_work_queue(struct wiphy *wiphy,
6112 struct wiphy_delayed_work *dwork,
6113 unsigned long delay);
6114
6115/**
6116 * wiphy_delayed_work_cancel - cancel previously queued delayed work
6117 * @wiphy: the wiphy, for debug purposes
6118 * @dwork: the delayed work to cancel
6119 *
6120 * Cancel the work *without* waiting for it, this assumes being
6121 * called under the wiphy mutex acquired by wiphy_lock().
6122 */
6123void wiphy_delayed_work_cancel(struct wiphy *wiphy,
6124 struct wiphy_delayed_work *dwork);
6125
6126/**
6127 * wiphy_delayed_work_flush - flush previously queued delayed work
6128 * @wiphy: the wiphy, for debug purposes
6129 * @dwork: the delayed work to flush
6130 *
6131 * Flush the work (i.e. run it if pending). This must be called
6132 * under the wiphy mutex acquired by wiphy_lock().
6133 */
6134void wiphy_delayed_work_flush(struct wiphy *wiphy,
6135 struct wiphy_delayed_work *dwork);
6136
6137/**
6138 * wiphy_delayed_work_pending - Find out whether a wiphy delayable
6139 * work item is currently pending.
6140 *
6141 * @wiphy: the wiphy, for debug purposes
6142 * @dwork: the delayed work in question
6143 *
6144 * Return: true if timer is pending, false otherwise
6145 *
6146 * How wiphy_delayed_work_queue() works is by setting a timer which
6147 * when it expires calls wiphy_work_queue() to queue the wiphy work.
6148 * Because wiphy_delayed_work_queue() uses mod_timer(), if it is
6149 * called twice and the second call happens before the first call
6150 * deadline, the work will rescheduled for the second deadline and
6151 * won't run before that.
6152 *
6153 * wiphy_delayed_work_pending() can be used to detect if calling
6154 * wiphy_work_delayed_work_queue() would start a new work schedule
6155 * or delayed a previous one. As seen below it cannot be used to
6156 * detect precisely if the work has finished to execute nor if it
6157 * is currently executing.
6158 *
6159 * CPU0 CPU1
6160 * wiphy_delayed_work_queue(wk)
6161 * mod_timer(wk->timer)
6162 * wiphy_delayed_work_pending(wk) -> true
6163 *
6164 * [...]
6165 * expire_timers(wk->timer)
6166 * detach_timer(wk->timer)
6167 * wiphy_delayed_work_pending(wk) -> false
6168 * wk->timer->function() |
6169 * wiphy_work_queue(wk) | delayed work pending
6170 * list_add_tail() | returns false but
6171 * queue_work(cfg80211_wiphy_work) | wk->func() has not
6172 * | been run yet
6173 * [...] |
6174 * cfg80211_wiphy_work() |
6175 * wk->func() V
6176 *
6177 */
6178bool wiphy_delayed_work_pending(struct wiphy *wiphy,
6179 struct wiphy_delayed_work *dwork);
6180
6181/**
6182 * enum ieee80211_ap_reg_power - regulatory power for an Access Point
6183 *
6184 * @IEEE80211_REG_UNSET_AP: Access Point has no regulatory power mode
6185 * @IEEE80211_REG_LPI_AP: Indoor Access Point
6186 * @IEEE80211_REG_SP_AP: Standard power Access Point
6187 * @IEEE80211_REG_VLP_AP: Very low power Access Point
6188 */
6189enum ieee80211_ap_reg_power {
6190 IEEE80211_REG_UNSET_AP,
6191 IEEE80211_REG_LPI_AP,
6192 IEEE80211_REG_SP_AP,
6193 IEEE80211_REG_VLP_AP,
6194};
6195
6196/**
6197 * struct wireless_dev - wireless device state
6198 *
6199 * For netdevs, this structure must be allocated by the driver
6200 * that uses the ieee80211_ptr field in struct net_device (this
6201 * is intentional so it can be allocated along with the netdev.)
6202 * It need not be registered then as netdev registration will
6203 * be intercepted by cfg80211 to see the new wireless device,
6204 * however, drivers must lock the wiphy before registering or
6205 * unregistering netdevs if they pre-create any netdevs (in ops
6206 * called from cfg80211, the wiphy is already locked.)
6207 *
6208 * For non-netdev uses, it must also be allocated by the driver
6209 * in response to the cfg80211 callbacks that require it, as
6210 * there's no netdev registration in that case it may not be
6211 * allocated outside of callback operations that return it.
6212 *
6213 * @wiphy: pointer to hardware description
6214 * @iftype: interface type
6215 * @registered: is this wdev already registered with cfg80211
6216 * @registering: indicates we're doing registration under wiphy lock
6217 * for the notifier
6218 * @list: (private) Used to collect the interfaces
6219 * @netdev: (private) Used to reference back to the netdev, may be %NULL
6220 * @identifier: (private) Identifier used in nl80211 to identify this
6221 * wireless device if it has no netdev
6222 * @u: union containing data specific to @iftype
6223 * @connected: indicates if connected or not (STA mode)
6224 * @wext: (private) Used by the internal wireless extensions compat code
6225 * @wext.ibss: (private) IBSS data part of wext handling
6226 * @wext.connect: (private) connection handling data
6227 * @wext.keys: (private) (WEP) key data
6228 * @wext.ie: (private) extra elements for association
6229 * @wext.ie_len: (private) length of extra elements
6230 * @wext.bssid: (private) selected network BSSID
6231 * @wext.ssid: (private) selected network SSID
6232 * @wext.default_key: (private) selected default key index
6233 * @wext.default_mgmt_key: (private) selected default management key index
6234 * @wext.prev_bssid: (private) previous BSSID for reassociation
6235 * @wext.prev_bssid_valid: (private) previous BSSID validity
6236 * @use_4addr: indicates 4addr mode is used on this interface, must be
6237 * set by driver (if supported) on add_interface BEFORE registering the
6238 * netdev and may otherwise be used by driver read-only, will be update
6239 * by cfg80211 on change_interface
6240 * @mgmt_registrations: list of registrations for management frames
6241 * @mgmt_registrations_need_update: mgmt registrations were updated,
6242 * need to propagate the update to the driver
6243 * @address: The address for this device, valid only if @netdev is %NULL
6244 * @is_running: true if this is a non-netdev device that has been started, e.g.
6245 * the P2P Device.
6246 * @ps: powersave mode is enabled
6247 * @ps_timeout: dynamic powersave timeout
6248 * @ap_unexpected_nlportid: (private) netlink port ID of application
6249 * registered for unexpected class 3 frames (AP mode)
6250 * @conn: (private) cfg80211 software SME connection state machine data
6251 * @connect_keys: (private) keys to set after connection is established
6252 * @conn_bss_type: connecting/connected BSS type
6253 * @conn_owner_nlportid: (private) connection owner socket port ID
6254 * @disconnect_wk: (private) auto-disconnect work
6255 * @disconnect_bssid: (private) the BSSID to use for auto-disconnect
6256 * @event_list: (private) list for internal event processing
6257 * @event_lock: (private) lock for event list
6258 * @owner_nlportid: (private) owner socket port ID
6259 * @nl_owner_dead: (private) owner socket went away
6260 * @cqm_rssi_work: (private) CQM RSSI reporting work
6261 * @cqm_config: (private) nl80211 RSSI monitor state
6262 * @pmsr_list: (private) peer measurement requests
6263 * @pmsr_lock: (private) peer measurements requests/results lock
6264 * @pmsr_free_wk: (private) peer measurements cleanup work
6265 * @unprot_beacon_reported: (private) timestamp of last
6266 * unprotected beacon report
6267 * @links: array of %IEEE80211_MLD_MAX_NUM_LINKS elements containing @addr
6268 * @ap and @client for each link
6269 * @links.cac_started: true if DFS channel availability check has been
6270 * started
6271 * @links.cac_start_time: timestamp (jiffies) when the dfs state was
6272 * entered.
6273 * @links.cac_time_ms: CAC time in ms
6274 * @valid_links: bitmap describing what elements of @links are valid
6275 * @radio_mask: Bitmask of radios that this interface is allowed to operate on.
6276 */
6277struct wireless_dev {
6278 struct wiphy *wiphy;
6279 enum nl80211_iftype iftype;
6280
6281 /* the remainder of this struct should be private to cfg80211 */
6282 struct list_head list;
6283 struct net_device *netdev;
6284
6285 u32 identifier;
6286
6287 struct list_head mgmt_registrations;
6288 u8 mgmt_registrations_need_update:1;
6289
6290 bool use_4addr, is_running, registered, registering;
6291
6292 u8 address[ETH_ALEN] __aligned(sizeof(u16));
6293
6294 /* currently used for IBSS and SME - might be rearranged later */
6295 struct cfg80211_conn *conn;
6296 struct cfg80211_cached_keys *connect_keys;
6297 enum ieee80211_bss_type conn_bss_type;
6298 u32 conn_owner_nlportid;
6299
6300 struct work_struct disconnect_wk;
6301 u8 disconnect_bssid[ETH_ALEN];
6302
6303 struct list_head event_list;
6304 spinlock_t event_lock;
6305
6306 u8 connected:1;
6307
6308 bool ps;
6309 int ps_timeout;
6310
6311 u32 ap_unexpected_nlportid;
6312
6313 u32 owner_nlportid;
6314 bool nl_owner_dead;
6315
6316#ifdef CONFIG_CFG80211_WEXT
6317 /* wext data */
6318 struct {
6319 struct cfg80211_ibss_params ibss;
6320 struct cfg80211_connect_params connect;
6321 struct cfg80211_cached_keys *keys;
6322 const u8 *ie;
6323 size_t ie_len;
6324 u8 bssid[ETH_ALEN];
6325 u8 prev_bssid[ETH_ALEN];
6326 u8 ssid[IEEE80211_MAX_SSID_LEN];
6327 s8 default_key, default_mgmt_key;
6328 bool prev_bssid_valid;
6329 } wext;
6330#endif
6331
6332 struct wiphy_work cqm_rssi_work;
6333 struct cfg80211_cqm_config __rcu *cqm_config;
6334
6335 struct list_head pmsr_list;
6336 spinlock_t pmsr_lock;
6337 struct work_struct pmsr_free_wk;
6338
6339 unsigned long unprot_beacon_reported;
6340
6341 union {
6342 struct {
6343 u8 connected_addr[ETH_ALEN] __aligned(2);
6344 u8 ssid[IEEE80211_MAX_SSID_LEN];
6345 u8 ssid_len;
6346 } client;
6347 struct {
6348 int beacon_interval;
6349 struct cfg80211_chan_def preset_chandef;
6350 struct cfg80211_chan_def chandef;
6351 u8 id[IEEE80211_MAX_MESH_ID_LEN];
6352 u8 id_len, id_up_len;
6353 } mesh;
6354 struct {
6355 struct cfg80211_chan_def preset_chandef;
6356 u8 ssid[IEEE80211_MAX_SSID_LEN];
6357 u8 ssid_len;
6358 } ap;
6359 struct {
6360 struct cfg80211_internal_bss *current_bss;
6361 struct cfg80211_chan_def chandef;
6362 int beacon_interval;
6363 u8 ssid[IEEE80211_MAX_SSID_LEN];
6364 u8 ssid_len;
6365 } ibss;
6366 struct {
6367 struct cfg80211_chan_def chandef;
6368 } ocb;
6369 } u;
6370
6371 struct {
6372 u8 addr[ETH_ALEN] __aligned(2);
6373 union {
6374 struct {
6375 unsigned int beacon_interval;
6376 struct cfg80211_chan_def chandef;
6377 } ap;
6378 struct {
6379 struct cfg80211_internal_bss *current_bss;
6380 } client;
6381 };
6382
6383 bool cac_started;
6384 unsigned long cac_start_time;
6385 unsigned int cac_time_ms;
6386 } links[IEEE80211_MLD_MAX_NUM_LINKS];
6387 u16 valid_links;
6388
6389 u32 radio_mask;
6390};
6391
6392static inline const u8 *wdev_address(struct wireless_dev *wdev)
6393{
6394 if (wdev->netdev)
6395 return wdev->netdev->dev_addr;
6396 return wdev->address;
6397}
6398
6399static inline bool wdev_running(struct wireless_dev *wdev)
6400{
6401 if (wdev->netdev)
6402 return netif_running(wdev->netdev);
6403 return wdev->is_running;
6404}
6405
6406/**
6407 * wdev_priv - return wiphy priv from wireless_dev
6408 *
6409 * @wdev: The wireless device whose wiphy's priv pointer to return
6410 * Return: The wiphy priv of @wdev.
6411 */
6412static inline void *wdev_priv(struct wireless_dev *wdev)
6413{
6414 BUG_ON(!wdev);
6415 return wiphy_priv(wdev->wiphy);
6416}
6417
6418/**
6419 * wdev_chandef - return chandef pointer from wireless_dev
6420 * @wdev: the wdev
6421 * @link_id: the link ID for MLO
6422 *
6423 * Return: The chandef depending on the mode, or %NULL.
6424 */
6425struct cfg80211_chan_def *wdev_chandef(struct wireless_dev *wdev,
6426 unsigned int link_id);
6427
6428static inline void WARN_INVALID_LINK_ID(struct wireless_dev *wdev,
6429 unsigned int link_id)
6430{
6431 WARN_ON(link_id && !wdev->valid_links);
6432 WARN_ON(wdev->valid_links &&
6433 !(wdev->valid_links & BIT(link_id)));
6434}
6435
6436#define for_each_valid_link(link_info, link_id) \
6437 for (link_id = 0; \
6438 link_id < ((link_info)->valid_links ? \
6439 ARRAY_SIZE((link_info)->links) : 1); \
6440 link_id++) \
6441 if (!(link_info)->valid_links || \
6442 ((link_info)->valid_links & BIT(link_id)))
6443
6444/**
6445 * DOC: Utility functions
6446 *
6447 * cfg80211 offers a number of utility functions that can be useful.
6448 */
6449
6450/**
6451 * ieee80211_channel_equal - compare two struct ieee80211_channel
6452 *
6453 * @a: 1st struct ieee80211_channel
6454 * @b: 2nd struct ieee80211_channel
6455 * Return: true if center frequency of @a == @b
6456 */
6457static inline bool
6458ieee80211_channel_equal(struct ieee80211_channel *a,
6459 struct ieee80211_channel *b)
6460{
6461 return (a->center_freq == b->center_freq &&
6462 a->freq_offset == b->freq_offset);
6463}
6464
6465/**
6466 * ieee80211_channel_to_khz - convert ieee80211_channel to frequency in KHz
6467 * @chan: struct ieee80211_channel to convert
6468 * Return: The corresponding frequency (in KHz)
6469 */
6470static inline u32
6471ieee80211_channel_to_khz(const struct ieee80211_channel *chan)
6472{
6473 return MHZ_TO_KHZ(chan->center_freq) + chan->freq_offset;
6474}
6475
6476/**
6477 * ieee80211_s1g_channel_width - get allowed channel width from @chan
6478 *
6479 * Only allowed for band NL80211_BAND_S1GHZ
6480 * @chan: channel
6481 * Return: The allowed channel width for this center_freq
6482 */
6483enum nl80211_chan_width
6484ieee80211_s1g_channel_width(const struct ieee80211_channel *chan);
6485
6486/**
6487 * ieee80211_channel_to_freq_khz - convert channel number to frequency
6488 * @chan: channel number
6489 * @band: band, necessary due to channel number overlap
6490 * Return: The corresponding frequency (in KHz), or 0 if the conversion failed.
6491 */
6492u32 ieee80211_channel_to_freq_khz(int chan, enum nl80211_band band);
6493
6494/**
6495 * ieee80211_channel_to_frequency - convert channel number to frequency
6496 * @chan: channel number
6497 * @band: band, necessary due to channel number overlap
6498 * Return: The corresponding frequency (in MHz), or 0 if the conversion failed.
6499 */
6500static inline int
6501ieee80211_channel_to_frequency(int chan, enum nl80211_band band)
6502{
6503 return KHZ_TO_MHZ(ieee80211_channel_to_freq_khz(chan, band));
6504}
6505
6506/**
6507 * ieee80211_freq_khz_to_channel - convert frequency to channel number
6508 * @freq: center frequency in KHz
6509 * Return: The corresponding channel, or 0 if the conversion failed.
6510 */
6511int ieee80211_freq_khz_to_channel(u32 freq);
6512
6513/**
6514 * ieee80211_frequency_to_channel - convert frequency to channel number
6515 * @freq: center frequency in MHz
6516 * Return: The corresponding channel, or 0 if the conversion failed.
6517 */
6518static inline int
6519ieee80211_frequency_to_channel(int freq)
6520{
6521 return ieee80211_freq_khz_to_channel(MHZ_TO_KHZ(freq));
6522}
6523
6524/**
6525 * ieee80211_get_channel_khz - get channel struct from wiphy for specified
6526 * frequency
6527 * @wiphy: the struct wiphy to get the channel for
6528 * @freq: the center frequency (in KHz) of the channel
6529 * Return: The channel struct from @wiphy at @freq.
6530 */
6531struct ieee80211_channel *
6532ieee80211_get_channel_khz(struct wiphy *wiphy, u32 freq);
6533
6534/**
6535 * ieee80211_get_channel - get channel struct from wiphy for specified frequency
6536 *
6537 * @wiphy: the struct wiphy to get the channel for
6538 * @freq: the center frequency (in MHz) of the channel
6539 * Return: The channel struct from @wiphy at @freq.
6540 */
6541static inline struct ieee80211_channel *
6542ieee80211_get_channel(struct wiphy *wiphy, int freq)
6543{
6544 return ieee80211_get_channel_khz(wiphy, MHZ_TO_KHZ(freq));
6545}
6546
6547/**
6548 * cfg80211_channel_is_psc - Check if the channel is a 6 GHz PSC
6549 * @chan: control channel to check
6550 *
6551 * The Preferred Scanning Channels (PSC) are defined in
6552 * Draft IEEE P802.11ax/D5.0, 26.17.2.3.3
6553 *
6554 * Return: %true if channel is a PSC, %false otherwise
6555 */
6556static inline bool cfg80211_channel_is_psc(struct ieee80211_channel *chan)
6557{
6558 if (chan->band != NL80211_BAND_6GHZ)
6559 return false;
6560
6561 return ieee80211_frequency_to_channel(chan->center_freq) % 16 == 5;
6562}
6563
6564/**
6565 * cfg80211_radio_chandef_valid - Check if the radio supports the chandef
6566 *
6567 * @radio: wiphy radio
6568 * @chandef: chandef for current channel
6569 *
6570 * Return: whether or not the given chandef is valid for the given radio
6571 */
6572bool cfg80211_radio_chandef_valid(const struct wiphy_radio *radio,
6573 const struct cfg80211_chan_def *chandef);
6574
6575/**
6576 * cfg80211_wdev_channel_allowed - Check if the wdev may use the channel
6577 *
6578 * @wdev: the wireless device
6579 * @chan: channel to check
6580 *
6581 * Return: whether or not the wdev may use the channel
6582 */
6583bool cfg80211_wdev_channel_allowed(struct wireless_dev *wdev,
6584 struct ieee80211_channel *chan);
6585
6586/**
6587 * ieee80211_get_response_rate - get basic rate for a given rate
6588 *
6589 * @sband: the band to look for rates in
6590 * @basic_rates: bitmap of basic rates
6591 * @bitrate: the bitrate for which to find the basic rate
6592 *
6593 * Return: The basic rate corresponding to a given bitrate, that
6594 * is the next lower bitrate contained in the basic rate map,
6595 * which is, for this function, given as a bitmap of indices of
6596 * rates in the band's bitrate table.
6597 */
6598const struct ieee80211_rate *
6599ieee80211_get_response_rate(struct ieee80211_supported_band *sband,
6600 u32 basic_rates, int bitrate);
6601
6602/**
6603 * ieee80211_mandatory_rates - get mandatory rates for a given band
6604 * @sband: the band to look for rates in
6605 *
6606 * Return: a bitmap of the mandatory rates for the given band, bits
6607 * are set according to the rate position in the bitrates array.
6608 */
6609u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband);
6610
6611/*
6612 * Radiotap parsing functions -- for controlled injection support
6613 *
6614 * Implemented in net/wireless/radiotap.c
6615 * Documentation in Documentation/networking/radiotap-headers.rst
6616 */
6617
6618struct radiotap_align_size {
6619 uint8_t align:4, size:4;
6620};
6621
6622struct ieee80211_radiotap_namespace {
6623 const struct radiotap_align_size *align_size;
6624 int n_bits;
6625 uint32_t oui;
6626 uint8_t subns;
6627};
6628
6629struct ieee80211_radiotap_vendor_namespaces {
6630 const struct ieee80211_radiotap_namespace *ns;
6631 int n_ns;
6632};
6633
6634/**
6635 * struct ieee80211_radiotap_iterator - tracks walk thru present radiotap args
6636 * @this_arg_index: index of current arg, valid after each successful call
6637 * to ieee80211_radiotap_iterator_next()
6638 * @this_arg: pointer to current radiotap arg; it is valid after each
6639 * call to ieee80211_radiotap_iterator_next() but also after
6640 * ieee80211_radiotap_iterator_init() where it will point to
6641 * the beginning of the actual data portion
6642 * @this_arg_size: length of the current arg, for convenience
6643 * @current_namespace: pointer to the current namespace definition
6644 * (or internally %NULL if the current namespace is unknown)
6645 * @is_radiotap_ns: indicates whether the current namespace is the default
6646 * radiotap namespace or not
6647 *
6648 * @_rtheader: pointer to the radiotap header we are walking through
6649 * @_max_length: length of radiotap header in cpu byte ordering
6650 * @_arg_index: next argument index
6651 * @_arg: next argument pointer
6652 * @_next_bitmap: internal pointer to next present u32
6653 * @_bitmap_shifter: internal shifter for curr u32 bitmap, b0 set == arg present
6654 * @_vns: vendor namespace definitions
6655 * @_next_ns_data: beginning of the next namespace's data
6656 * @_reset_on_ext: internal; reset the arg index to 0 when going to the
6657 * next bitmap word
6658 *
6659 * Describes the radiotap parser state. Fields prefixed with an underscore
6660 * must not be used by users of the parser, only by the parser internally.
6661 */
6662
6663struct ieee80211_radiotap_iterator {
6664 struct ieee80211_radiotap_header *_rtheader;
6665 const struct ieee80211_radiotap_vendor_namespaces *_vns;
6666 const struct ieee80211_radiotap_namespace *current_namespace;
6667
6668 unsigned char *_arg, *_next_ns_data;
6669 __le32 *_next_bitmap;
6670
6671 unsigned char *this_arg;
6672 int this_arg_index;
6673 int this_arg_size;
6674
6675 int is_radiotap_ns;
6676
6677 int _max_length;
6678 int _arg_index;
6679 uint32_t _bitmap_shifter;
6680 int _reset_on_ext;
6681};
6682
6683int
6684ieee80211_radiotap_iterator_init(struct ieee80211_radiotap_iterator *iterator,
6685 struct ieee80211_radiotap_header *radiotap_header,
6686 int max_length,
6687 const struct ieee80211_radiotap_vendor_namespaces *vns);
6688
6689int
6690ieee80211_radiotap_iterator_next(struct ieee80211_radiotap_iterator *iterator);
6691
6692
6693extern const unsigned char rfc1042_header[6];
6694extern const unsigned char bridge_tunnel_header[6];
6695
6696/**
6697 * ieee80211_get_hdrlen_from_skb - get header length from data
6698 *
6699 * @skb: the frame
6700 *
6701 * Given an skb with a raw 802.11 header at the data pointer this function
6702 * returns the 802.11 header length.
6703 *
6704 * Return: The 802.11 header length in bytes (not including encryption
6705 * headers). Or 0 if the data in the sk_buff is too short to contain a valid
6706 * 802.11 header.
6707 */
6708unsigned int ieee80211_get_hdrlen_from_skb(const struct sk_buff *skb);
6709
6710/**
6711 * ieee80211_hdrlen - get header length in bytes from frame control
6712 * @fc: frame control field in little-endian format
6713 * Return: The header length in bytes.
6714 */
6715unsigned int __attribute_const__ ieee80211_hdrlen(__le16 fc);
6716
6717/**
6718 * ieee80211_get_mesh_hdrlen - get mesh extension header length
6719 * @meshhdr: the mesh extension header, only the flags field
6720 * (first byte) will be accessed
6721 * Return: The length of the extension header, which is always at
6722 * least 6 bytes and at most 18 if address 5 and 6 are present.
6723 */
6724unsigned int ieee80211_get_mesh_hdrlen(struct ieee80211s_hdr *meshhdr);
6725
6726/**
6727 * DOC: Data path helpers
6728 *
6729 * In addition to generic utilities, cfg80211 also offers
6730 * functions that help implement the data path for devices
6731 * that do not do the 802.11/802.3 conversion on the device.
6732 */
6733
6734/**
6735 * ieee80211_data_to_8023_exthdr - convert an 802.11 data frame to 802.3
6736 * @skb: the 802.11 data frame
6737 * @ehdr: pointer to a &struct ethhdr that will get the header, instead
6738 * of it being pushed into the SKB
6739 * @addr: the device MAC address
6740 * @iftype: the virtual interface type
6741 * @data_offset: offset of payload after the 802.11 header
6742 * @is_amsdu: true if the 802.11 header is A-MSDU
6743 * Return: 0 on success. Non-zero on error.
6744 */
6745int ieee80211_data_to_8023_exthdr(struct sk_buff *skb, struct ethhdr *ehdr,
6746 const u8 *addr, enum nl80211_iftype iftype,
6747 u8 data_offset, bool is_amsdu);
6748
6749/**
6750 * ieee80211_data_to_8023 - convert an 802.11 data frame to 802.3
6751 * @skb: the 802.11 data frame
6752 * @addr: the device MAC address
6753 * @iftype: the virtual interface type
6754 * Return: 0 on success. Non-zero on error.
6755 */
6756static inline int ieee80211_data_to_8023(struct sk_buff *skb, const u8 *addr,
6757 enum nl80211_iftype iftype)
6758{
6759 return ieee80211_data_to_8023_exthdr(skb, NULL, addr, iftype, 0, false);
6760}
6761
6762/**
6763 * ieee80211_is_valid_amsdu - check if subframe lengths of an A-MSDU are valid
6764 *
6765 * This is used to detect non-standard A-MSDU frames, e.g. the ones generated
6766 * by ath10k and ath11k, where the subframe length includes the length of the
6767 * mesh control field.
6768 *
6769 * @skb: The input A-MSDU frame without any headers.
6770 * @mesh_hdr: the type of mesh header to test
6771 * 0: non-mesh A-MSDU length field
6772 * 1: big-endian mesh A-MSDU length field
6773 * 2: little-endian mesh A-MSDU length field
6774 * Returns: true if subframe header lengths are valid for the @mesh_hdr mode
6775 */
6776bool ieee80211_is_valid_amsdu(struct sk_buff *skb, u8 mesh_hdr);
6777
6778/**
6779 * ieee80211_amsdu_to_8023s - decode an IEEE 802.11n A-MSDU frame
6780 *
6781 * Decode an IEEE 802.11 A-MSDU and convert it to a list of 802.3 frames.
6782 * The @list will be empty if the decode fails. The @skb must be fully
6783 * header-less before being passed in here; it is freed in this function.
6784 *
6785 * @skb: The input A-MSDU frame without any headers.
6786 * @list: The output list of 802.3 frames. It must be allocated and
6787 * initialized by the caller.
6788 * @addr: The device MAC address.
6789 * @iftype: The device interface type.
6790 * @extra_headroom: The hardware extra headroom for SKBs in the @list.
6791 * @check_da: DA to check in the inner ethernet header, or NULL
6792 * @check_sa: SA to check in the inner ethernet header, or NULL
6793 * @mesh_control: see mesh_hdr in ieee80211_is_valid_amsdu
6794 */
6795void ieee80211_amsdu_to_8023s(struct sk_buff *skb, struct sk_buff_head *list,
6796 const u8 *addr, enum nl80211_iftype iftype,
6797 const unsigned int extra_headroom,
6798 const u8 *check_da, const u8 *check_sa,
6799 u8 mesh_control);
6800
6801/**
6802 * ieee80211_get_8023_tunnel_proto - get RFC1042 or bridge tunnel encap protocol
6803 *
6804 * Check for RFC1042 or bridge tunnel header and fetch the encapsulated
6805 * protocol.
6806 *
6807 * @hdr: pointer to the MSDU payload
6808 * @proto: destination pointer to store the protocol
6809 * Return: true if encapsulation was found
6810 */
6811bool ieee80211_get_8023_tunnel_proto(const void *hdr, __be16 *proto);
6812
6813/**
6814 * ieee80211_strip_8023_mesh_hdr - strip mesh header from converted 802.3 frames
6815 *
6816 * Strip the mesh header, which was left in by ieee80211_data_to_8023 as part
6817 * of the MSDU data. Also move any source/destination addresses from the mesh
6818 * header to the ethernet header (if present).
6819 *
6820 * @skb: The 802.3 frame with embedded mesh header
6821 *
6822 * Return: 0 on success. Non-zero on error.
6823 */
6824int ieee80211_strip_8023_mesh_hdr(struct sk_buff *skb);
6825
6826/**
6827 * cfg80211_classify8021d - determine the 802.1p/1d tag for a data frame
6828 * @skb: the data frame
6829 * @qos_map: Interworking QoS mapping or %NULL if not in use
6830 * Return: The 802.1p/1d tag.
6831 */
6832unsigned int cfg80211_classify8021d(struct sk_buff *skb,
6833 struct cfg80211_qos_map *qos_map);
6834
6835/**
6836 * cfg80211_find_elem_match - match information element and byte array in data
6837 *
6838 * @eid: element ID
6839 * @ies: data consisting of IEs
6840 * @len: length of data
6841 * @match: byte array to match
6842 * @match_len: number of bytes in the match array
6843 * @match_offset: offset in the IE data where the byte array should match.
6844 * Note the difference to cfg80211_find_ie_match() which considers
6845 * the offset to start from the element ID byte, but here we take
6846 * the data portion instead.
6847 *
6848 * Return: %NULL if the element ID could not be found or if
6849 * the element is invalid (claims to be longer than the given
6850 * data) or if the byte array doesn't match; otherwise return the
6851 * requested element struct.
6852 *
6853 * Note: There are no checks on the element length other than
6854 * having to fit into the given data and being large enough for the
6855 * byte array to match.
6856 */
6857const struct element *
6858cfg80211_find_elem_match(u8 eid, const u8 *ies, unsigned int len,
6859 const u8 *match, unsigned int match_len,
6860 unsigned int match_offset);
6861
6862/**
6863 * cfg80211_find_ie_match - match information element and byte array in data
6864 *
6865 * @eid: element ID
6866 * @ies: data consisting of IEs
6867 * @len: length of data
6868 * @match: byte array to match
6869 * @match_len: number of bytes in the match array
6870 * @match_offset: offset in the IE where the byte array should match.
6871 * If match_len is zero, this must also be set to zero.
6872 * Otherwise this must be set to 2 or more, because the first
6873 * byte is the element id, which is already compared to eid, and
6874 * the second byte is the IE length.
6875 *
6876 * Return: %NULL if the element ID could not be found or if
6877 * the element is invalid (claims to be longer than the given
6878 * data) or if the byte array doesn't match, or a pointer to the first
6879 * byte of the requested element, that is the byte containing the
6880 * element ID.
6881 *
6882 * Note: There are no checks on the element length other than
6883 * having to fit into the given data and being large enough for the
6884 * byte array to match.
6885 */
6886static inline const u8 *
6887cfg80211_find_ie_match(u8 eid, const u8 *ies, unsigned int len,
6888 const u8 *match, unsigned int match_len,
6889 unsigned int match_offset)
6890{
6891 /* match_offset can't be smaller than 2, unless match_len is
6892 * zero, in which case match_offset must be zero as well.
6893 */
6894 if (WARN_ON((match_len && match_offset < 2) ||
6895 (!match_len && match_offset)))
6896 return NULL;
6897
6898 return (const void *)cfg80211_find_elem_match(eid, ies, len,
6899 match, match_len,
6900 match_offset ?
6901 match_offset - 2 : 0);
6902}
6903
6904/**
6905 * cfg80211_find_elem - find information element in data
6906 *
6907 * @eid: element ID
6908 * @ies: data consisting of IEs
6909 * @len: length of data
6910 *
6911 * Return: %NULL if the element ID could not be found or if
6912 * the element is invalid (claims to be longer than the given
6913 * data) or if the byte array doesn't match; otherwise return the
6914 * requested element struct.
6915 *
6916 * Note: There are no checks on the element length other than
6917 * having to fit into the given data.
6918 */
6919static inline const struct element *
6920cfg80211_find_elem(u8 eid, const u8 *ies, int len)
6921{
6922 return cfg80211_find_elem_match(eid, ies, len, NULL, 0, 0);
6923}
6924
6925/**
6926 * cfg80211_find_ie - find information element in data
6927 *
6928 * @eid: element ID
6929 * @ies: data consisting of IEs
6930 * @len: length of data
6931 *
6932 * Return: %NULL if the element ID could not be found or if
6933 * the element is invalid (claims to be longer than the given
6934 * data), or a pointer to the first byte of the requested
6935 * element, that is the byte containing the element ID.
6936 *
6937 * Note: There are no checks on the element length other than
6938 * having to fit into the given data.
6939 */
6940static inline const u8 *cfg80211_find_ie(u8 eid, const u8 *ies, int len)
6941{
6942 return cfg80211_find_ie_match(eid, ies, len, NULL, 0, 0);
6943}
6944
6945/**
6946 * cfg80211_find_ext_elem - find information element with EID Extension in data
6947 *
6948 * @ext_eid: element ID Extension
6949 * @ies: data consisting of IEs
6950 * @len: length of data
6951 *
6952 * Return: %NULL if the extended element could not be found or if
6953 * the element is invalid (claims to be longer than the given
6954 * data) or if the byte array doesn't match; otherwise return the
6955 * requested element struct.
6956 *
6957 * Note: There are no checks on the element length other than
6958 * having to fit into the given data.
6959 */
6960static inline const struct element *
6961cfg80211_find_ext_elem(u8 ext_eid, const u8 *ies, int len)
6962{
6963 return cfg80211_find_elem_match(WLAN_EID_EXTENSION, ies, len,
6964 &ext_eid, 1, 0);
6965}
6966
6967/**
6968 * cfg80211_find_ext_ie - find information element with EID Extension in data
6969 *
6970 * @ext_eid: element ID Extension
6971 * @ies: data consisting of IEs
6972 * @len: length of data
6973 *
6974 * Return: %NULL if the extended element ID could not be found or if
6975 * the element is invalid (claims to be longer than the given
6976 * data), or a pointer to the first byte of the requested
6977 * element, that is the byte containing the element ID.
6978 *
6979 * Note: There are no checks on the element length other than
6980 * having to fit into the given data.
6981 */
6982static inline const u8 *cfg80211_find_ext_ie(u8 ext_eid, const u8 *ies, int len)
6983{
6984 return cfg80211_find_ie_match(WLAN_EID_EXTENSION, ies, len,
6985 &ext_eid, 1, 2);
6986}
6987
6988/**
6989 * cfg80211_find_vendor_elem - find vendor specific information element in data
6990 *
6991 * @oui: vendor OUI
6992 * @oui_type: vendor-specific OUI type (must be < 0xff), negative means any
6993 * @ies: data consisting of IEs
6994 * @len: length of data
6995 *
6996 * Return: %NULL if the vendor specific element ID could not be found or if the
6997 * element is invalid (claims to be longer than the given data); otherwise
6998 * return the element structure for the requested element.
6999 *
7000 * Note: There are no checks on the element length other than having to fit into
7001 * the given data.
7002 */
7003const struct element *cfg80211_find_vendor_elem(unsigned int oui, int oui_type,
7004 const u8 *ies,
7005 unsigned int len);
7006
7007/**
7008 * cfg80211_find_vendor_ie - find vendor specific information element in data
7009 *
7010 * @oui: vendor OUI
7011 * @oui_type: vendor-specific OUI type (must be < 0xff), negative means any
7012 * @ies: data consisting of IEs
7013 * @len: length of data
7014 *
7015 * Return: %NULL if the vendor specific element ID could not be found or if the
7016 * element is invalid (claims to be longer than the given data), or a pointer to
7017 * the first byte of the requested element, that is the byte containing the
7018 * element ID.
7019 *
7020 * Note: There are no checks on the element length other than having to fit into
7021 * the given data.
7022 */
7023static inline const u8 *
7024cfg80211_find_vendor_ie(unsigned int oui, int oui_type,
7025 const u8 *ies, unsigned int len)
7026{
7027 return (const void *)cfg80211_find_vendor_elem(oui, oui_type, ies, len);
7028}
7029
7030/**
7031 * enum cfg80211_rnr_iter_ret - reduced neighbor report iteration state
7032 * @RNR_ITER_CONTINUE: continue iterating with the next entry
7033 * @RNR_ITER_BREAK: break iteration and return success
7034 * @RNR_ITER_ERROR: break iteration and return error
7035 */
7036enum cfg80211_rnr_iter_ret {
7037 RNR_ITER_CONTINUE,
7038 RNR_ITER_BREAK,
7039 RNR_ITER_ERROR,
7040};
7041
7042/**
7043 * cfg80211_iter_rnr - iterate reduced neighbor report entries
7044 * @elems: the frame elements to iterate RNR elements and then
7045 * their entries in
7046 * @elems_len: length of the elements
7047 * @iter: iteration function, see also &enum cfg80211_rnr_iter_ret
7048 * for the return value
7049 * @iter_data: additional data passed to the iteration function
7050 * Return: %true on success (after successfully iterating all entries
7051 * or if the iteration function returned %RNR_ITER_BREAK),
7052 * %false on error (iteration function returned %RNR_ITER_ERROR
7053 * or elements were malformed.)
7054 */
7055bool cfg80211_iter_rnr(const u8 *elems, size_t elems_len,
7056 enum cfg80211_rnr_iter_ret
7057 (*iter)(void *data, u8 type,
7058 const struct ieee80211_neighbor_ap_info *info,
7059 const u8 *tbtt_info, u8 tbtt_info_len),
7060 void *iter_data);
7061
7062/**
7063 * cfg80211_defragment_element - Defrag the given element data into a buffer
7064 *
7065 * @elem: the element to defragment
7066 * @ies: elements where @elem is contained
7067 * @ieslen: length of @ies
7068 * @data: buffer to store element data, or %NULL to just determine size
7069 * @data_len: length of @data, or 0
7070 * @frag_id: the element ID of fragments
7071 *
7072 * Return: length of @data, or -EINVAL on error
7073 *
7074 * Copy out all data from an element that may be fragmented into @data, while
7075 * skipping all headers.
7076 *
7077 * The function uses memmove() internally. It is acceptable to defragment an
7078 * element in-place.
7079 */
7080ssize_t cfg80211_defragment_element(const struct element *elem, const u8 *ies,
7081 size_t ieslen, u8 *data, size_t data_len,
7082 u8 frag_id);
7083
7084/**
7085 * cfg80211_send_layer2_update - send layer 2 update frame
7086 *
7087 * @dev: network device
7088 * @addr: STA MAC address
7089 *
7090 * Wireless drivers can use this function to update forwarding tables in bridge
7091 * devices upon STA association.
7092 */
7093void cfg80211_send_layer2_update(struct net_device *dev, const u8 *addr);
7094
7095/**
7096 * DOC: Regulatory enforcement infrastructure
7097 *
7098 * TODO
7099 */
7100
7101/**
7102 * regulatory_hint - driver hint to the wireless core a regulatory domain
7103 * @wiphy: the wireless device giving the hint (used only for reporting
7104 * conflicts)
7105 * @alpha2: the ISO/IEC 3166 alpha2 the driver claims its regulatory domain
7106 * should be in. If @rd is set this should be NULL. Note that if you
7107 * set this to NULL you should still set rd->alpha2 to some accepted
7108 * alpha2.
7109 *
7110 * Wireless drivers can use this function to hint to the wireless core
7111 * what it believes should be the current regulatory domain by
7112 * giving it an ISO/IEC 3166 alpha2 country code it knows its regulatory
7113 * domain should be in or by providing a completely build regulatory domain.
7114 * If the driver provides an ISO/IEC 3166 alpha2 userspace will be queried
7115 * for a regulatory domain structure for the respective country.
7116 *
7117 * The wiphy must have been registered to cfg80211 prior to this call.
7118 * For cfg80211 drivers this means you must first use wiphy_register(),
7119 * for mac80211 drivers you must first use ieee80211_register_hw().
7120 *
7121 * Drivers should check the return value, its possible you can get
7122 * an -ENOMEM.
7123 *
7124 * Return: 0 on success. -ENOMEM.
7125 */
7126int regulatory_hint(struct wiphy *wiphy, const char *alpha2);
7127
7128/**
7129 * regulatory_set_wiphy_regd - set regdom info for self managed drivers
7130 * @wiphy: the wireless device we want to process the regulatory domain on
7131 * @rd: the regulatory domain information to use for this wiphy
7132 *
7133 * Set the regulatory domain information for self-managed wiphys, only they
7134 * may use this function. See %REGULATORY_WIPHY_SELF_MANAGED for more
7135 * information.
7136 *
7137 * Return: 0 on success. -EINVAL, -EPERM
7138 */
7139int regulatory_set_wiphy_regd(struct wiphy *wiphy,
7140 struct ieee80211_regdomain *rd);
7141
7142/**
7143 * regulatory_set_wiphy_regd_sync - set regdom for self-managed drivers
7144 * @wiphy: the wireless device we want to process the regulatory domain on
7145 * @rd: the regulatory domain information to use for this wiphy
7146 *
7147 * This functions requires the RTNL and the wiphy mutex to be held and
7148 * applies the new regdomain synchronously to this wiphy. For more details
7149 * see regulatory_set_wiphy_regd().
7150 *
7151 * Return: 0 on success. -EINVAL, -EPERM
7152 */
7153int regulatory_set_wiphy_regd_sync(struct wiphy *wiphy,
7154 struct ieee80211_regdomain *rd);
7155
7156/**
7157 * wiphy_apply_custom_regulatory - apply a custom driver regulatory domain
7158 * @wiphy: the wireless device we want to process the regulatory domain on
7159 * @regd: the custom regulatory domain to use for this wiphy
7160 *
7161 * Drivers can sometimes have custom regulatory domains which do not apply
7162 * to a specific country. Drivers can use this to apply such custom regulatory
7163 * domains. This routine must be called prior to wiphy registration. The
7164 * custom regulatory domain will be trusted completely and as such previous
7165 * default channel settings will be disregarded. If no rule is found for a
7166 * channel on the regulatory domain the channel will be disabled.
7167 * Drivers using this for a wiphy should also set the wiphy flag
7168 * REGULATORY_CUSTOM_REG or cfg80211 will set it for the wiphy
7169 * that called this helper.
7170 */
7171void wiphy_apply_custom_regulatory(struct wiphy *wiphy,
7172 const struct ieee80211_regdomain *regd);
7173
7174/**
7175 * freq_reg_info - get regulatory information for the given frequency
7176 * @wiphy: the wiphy for which we want to process this rule for
7177 * @center_freq: Frequency in KHz for which we want regulatory information for
7178 *
7179 * Use this function to get the regulatory rule for a specific frequency on
7180 * a given wireless device. If the device has a specific regulatory domain
7181 * it wants to follow we respect that unless a country IE has been received
7182 * and processed already.
7183 *
7184 * Return: A valid pointer, or, when an error occurs, for example if no rule
7185 * can be found, the return value is encoded using ERR_PTR(). Use IS_ERR() to
7186 * check and PTR_ERR() to obtain the numeric return value. The numeric return
7187 * value will be -ERANGE if we determine the given center_freq does not even
7188 * have a regulatory rule for a frequency range in the center_freq's band.
7189 * See freq_in_rule_band() for our current definition of a band -- this is
7190 * purely subjective and right now it's 802.11 specific.
7191 */
7192const struct ieee80211_reg_rule *freq_reg_info(struct wiphy *wiphy,
7193 u32 center_freq);
7194
7195/**
7196 * reg_initiator_name - map regulatory request initiator enum to name
7197 * @initiator: the regulatory request initiator
7198 *
7199 * You can use this to map the regulatory request initiator enum to a
7200 * proper string representation.
7201 *
7202 * Return: pointer to string representation of the initiator
7203 */
7204const char *reg_initiator_name(enum nl80211_reg_initiator initiator);
7205
7206/**
7207 * regulatory_pre_cac_allowed - check if pre-CAC allowed in the current regdom
7208 * @wiphy: wiphy for which pre-CAC capability is checked.
7209 *
7210 * Pre-CAC is allowed only in some regdomains (notable ETSI).
7211 *
7212 * Return: %true if allowed, %false otherwise
7213 */
7214bool regulatory_pre_cac_allowed(struct wiphy *wiphy);
7215
7216/**
7217 * DOC: Internal regulatory db functions
7218 *
7219 */
7220
7221/**
7222 * reg_query_regdb_wmm - Query internal regulatory db for wmm rule
7223 * Regulatory self-managed driver can use it to proactively
7224 *
7225 * @alpha2: the ISO/IEC 3166 alpha2 wmm rule to be queried.
7226 * @freq: the frequency (in MHz) to be queried.
7227 * @rule: pointer to store the wmm rule from the regulatory db.
7228 *
7229 * Self-managed wireless drivers can use this function to query
7230 * the internal regulatory database to check whether the given
7231 * ISO/IEC 3166 alpha2 country and freq have wmm rule limitations.
7232 *
7233 * Drivers should check the return value, its possible you can get
7234 * an -ENODATA.
7235 *
7236 * Return: 0 on success. -ENODATA.
7237 */
7238int reg_query_regdb_wmm(char *alpha2, int freq,
7239 struct ieee80211_reg_rule *rule);
7240
7241/*
7242 * callbacks for asynchronous cfg80211 methods, notification
7243 * functions and BSS handling helpers
7244 */
7245
7246/**
7247 * cfg80211_scan_done - notify that scan finished
7248 *
7249 * @request: the corresponding scan request
7250 * @info: information about the completed scan
7251 */
7252void cfg80211_scan_done(struct cfg80211_scan_request *request,
7253 struct cfg80211_scan_info *info);
7254
7255/**
7256 * cfg80211_sched_scan_results - notify that new scan results are available
7257 *
7258 * @wiphy: the wiphy which got scheduled scan results
7259 * @reqid: identifier for the related scheduled scan request
7260 */
7261void cfg80211_sched_scan_results(struct wiphy *wiphy, u64 reqid);
7262
7263/**
7264 * cfg80211_sched_scan_stopped - notify that the scheduled scan has stopped
7265 *
7266 * @wiphy: the wiphy on which the scheduled scan stopped
7267 * @reqid: identifier for the related scheduled scan request
7268 *
7269 * The driver can call this function to inform cfg80211 that the
7270 * scheduled scan had to be stopped, for whatever reason. The driver
7271 * is then called back via the sched_scan_stop operation when done.
7272 */
7273void cfg80211_sched_scan_stopped(struct wiphy *wiphy, u64 reqid);
7274
7275/**
7276 * cfg80211_sched_scan_stopped_locked - notify that the scheduled scan has stopped
7277 *
7278 * @wiphy: the wiphy on which the scheduled scan stopped
7279 * @reqid: identifier for the related scheduled scan request
7280 *
7281 * The driver can call this function to inform cfg80211 that the
7282 * scheduled scan had to be stopped, for whatever reason. The driver
7283 * is then called back via the sched_scan_stop operation when done.
7284 * This function should be called with the wiphy mutex held.
7285 */
7286void cfg80211_sched_scan_stopped_locked(struct wiphy *wiphy, u64 reqid);
7287
7288/**
7289 * cfg80211_inform_bss_frame_data - inform cfg80211 of a received BSS frame
7290 * @wiphy: the wiphy reporting the BSS
7291 * @data: the BSS metadata
7292 * @mgmt: the management frame (probe response or beacon)
7293 * @len: length of the management frame
7294 * @gfp: context flags
7295 *
7296 * This informs cfg80211 that BSS information was found and
7297 * the BSS should be updated/added.
7298 *
7299 * Return: A referenced struct, must be released with cfg80211_put_bss()!
7300 * Or %NULL on error.
7301 */
7302struct cfg80211_bss * __must_check
7303cfg80211_inform_bss_frame_data(struct wiphy *wiphy,
7304 struct cfg80211_inform_bss *data,
7305 struct ieee80211_mgmt *mgmt, size_t len,
7306 gfp_t gfp);
7307
7308static inline struct cfg80211_bss * __must_check
7309cfg80211_inform_bss_frame(struct wiphy *wiphy,
7310 struct ieee80211_channel *rx_channel,
7311 struct ieee80211_mgmt *mgmt, size_t len,
7312 s32 signal, gfp_t gfp)
7313{
7314 struct cfg80211_inform_bss data = {
7315 .chan = rx_channel,
7316 .signal = signal,
7317 };
7318
7319 return cfg80211_inform_bss_frame_data(wiphy, &data, mgmt, len, gfp);
7320}
7321
7322/**
7323 * cfg80211_gen_new_bssid - generate a nontransmitted BSSID for multi-BSSID
7324 * @bssid: transmitter BSSID
7325 * @max_bssid: max BSSID indicator, taken from Multiple BSSID element
7326 * @mbssid_index: BSSID index, taken from Multiple BSSID index element
7327 * @new_bssid: calculated nontransmitted BSSID
7328 */
7329static inline void cfg80211_gen_new_bssid(const u8 *bssid, u8 max_bssid,
7330 u8 mbssid_index, u8 *new_bssid)
7331{
7332 u64 bssid_u64 = ether_addr_to_u64(bssid);
7333 u64 mask = GENMASK_ULL(max_bssid - 1, 0);
7334 u64 new_bssid_u64;
7335
7336 new_bssid_u64 = bssid_u64 & ~mask;
7337
7338 new_bssid_u64 |= ((bssid_u64 & mask) + mbssid_index) & mask;
7339
7340 u64_to_ether_addr(new_bssid_u64, new_bssid);
7341}
7342
7343/**
7344 * cfg80211_is_element_inherited - returns if element ID should be inherited
7345 * @element: element to check
7346 * @non_inherit_element: non inheritance element
7347 *
7348 * Return: %true if should be inherited, %false otherwise
7349 */
7350bool cfg80211_is_element_inherited(const struct element *element,
7351 const struct element *non_inherit_element);
7352
7353/**
7354 * cfg80211_merge_profile - merges a MBSSID profile if it is split between IEs
7355 * @ie: ies
7356 * @ielen: length of IEs
7357 * @mbssid_elem: current MBSSID element
7358 * @sub_elem: current MBSSID subelement (profile)
7359 * @merged_ie: location of the merged profile
7360 * @max_copy_len: max merged profile length
7361 *
7362 * Return: the number of bytes merged
7363 */
7364size_t cfg80211_merge_profile(const u8 *ie, size_t ielen,
7365 const struct element *mbssid_elem,
7366 const struct element *sub_elem,
7367 u8 *merged_ie, size_t max_copy_len);
7368
7369/**
7370 * enum cfg80211_bss_frame_type - frame type that the BSS data came from
7371 * @CFG80211_BSS_FTYPE_UNKNOWN: driver doesn't know whether the data is
7372 * from a beacon or probe response
7373 * @CFG80211_BSS_FTYPE_BEACON: data comes from a beacon
7374 * @CFG80211_BSS_FTYPE_PRESP: data comes from a probe response
7375 * @CFG80211_BSS_FTYPE_S1G_BEACON: data comes from an S1G beacon
7376 */
7377enum cfg80211_bss_frame_type {
7378 CFG80211_BSS_FTYPE_UNKNOWN,
7379 CFG80211_BSS_FTYPE_BEACON,
7380 CFG80211_BSS_FTYPE_PRESP,
7381 CFG80211_BSS_FTYPE_S1G_BEACON,
7382};
7383
7384/**
7385 * cfg80211_get_ies_channel_number - returns the channel number from ies
7386 * @ie: IEs
7387 * @ielen: length of IEs
7388 * @band: enum nl80211_band of the channel
7389 *
7390 * Return: the channel number, or -1 if none could be determined.
7391 */
7392int cfg80211_get_ies_channel_number(const u8 *ie, size_t ielen,
7393 enum nl80211_band band);
7394
7395/**
7396 * cfg80211_ssid_eq - compare two SSIDs
7397 * @a: first SSID
7398 * @b: second SSID
7399 *
7400 * Return: %true if SSIDs are equal, %false otherwise.
7401 */
7402static inline bool
7403cfg80211_ssid_eq(struct cfg80211_ssid *a, struct cfg80211_ssid *b)
7404{
7405 if (WARN_ON(!a || !b))
7406 return false;
7407 if (a->ssid_len != b->ssid_len)
7408 return false;
7409 return memcmp(a->ssid, b->ssid, a->ssid_len) ? false : true;
7410}
7411
7412/**
7413 * cfg80211_inform_bss_data - inform cfg80211 of a new BSS
7414 *
7415 * @wiphy: the wiphy reporting the BSS
7416 * @data: the BSS metadata
7417 * @ftype: frame type (if known)
7418 * @bssid: the BSSID of the BSS
7419 * @tsf: the TSF sent by the peer in the beacon/probe response (or 0)
7420 * @capability: the capability field sent by the peer
7421 * @beacon_interval: the beacon interval announced by the peer
7422 * @ie: additional IEs sent by the peer
7423 * @ielen: length of the additional IEs
7424 * @gfp: context flags
7425 *
7426 * This informs cfg80211 that BSS information was found and
7427 * the BSS should be updated/added.
7428 *
7429 * Return: A referenced struct, must be released with cfg80211_put_bss()!
7430 * Or %NULL on error.
7431 */
7432struct cfg80211_bss * __must_check
7433cfg80211_inform_bss_data(struct wiphy *wiphy,
7434 struct cfg80211_inform_bss *data,
7435 enum cfg80211_bss_frame_type ftype,
7436 const u8 *bssid, u64 tsf, u16 capability,
7437 u16 beacon_interval, const u8 *ie, size_t ielen,
7438 gfp_t gfp);
7439
7440static inline struct cfg80211_bss * __must_check
7441cfg80211_inform_bss(struct wiphy *wiphy,
7442 struct ieee80211_channel *rx_channel,
7443 enum cfg80211_bss_frame_type ftype,
7444 const u8 *bssid, u64 tsf, u16 capability,
7445 u16 beacon_interval, const u8 *ie, size_t ielen,
7446 s32 signal, gfp_t gfp)
7447{
7448 struct cfg80211_inform_bss data = {
7449 .chan = rx_channel,
7450 .signal = signal,
7451 };
7452
7453 return cfg80211_inform_bss_data(wiphy, &data, ftype, bssid, tsf,
7454 capability, beacon_interval, ie, ielen,
7455 gfp);
7456}
7457
7458/**
7459 * __cfg80211_get_bss - get a BSS reference
7460 * @wiphy: the wiphy this BSS struct belongs to
7461 * @channel: the channel to search on (or %NULL)
7462 * @bssid: the desired BSSID (or %NULL)
7463 * @ssid: the desired SSID (or %NULL)
7464 * @ssid_len: length of the SSID (or 0)
7465 * @bss_type: type of BSS, see &enum ieee80211_bss_type
7466 * @privacy: privacy filter, see &enum ieee80211_privacy
7467 * @use_for: indicates which use is intended
7468 *
7469 * Return: Reference-counted BSS on success. %NULL on error.
7470 */
7471struct cfg80211_bss *__cfg80211_get_bss(struct wiphy *wiphy,
7472 struct ieee80211_channel *channel,
7473 const u8 *bssid,
7474 const u8 *ssid, size_t ssid_len,
7475 enum ieee80211_bss_type bss_type,
7476 enum ieee80211_privacy privacy,
7477 u32 use_for);
7478
7479/**
7480 * cfg80211_get_bss - get a BSS reference
7481 * @wiphy: the wiphy this BSS struct belongs to
7482 * @channel: the channel to search on (or %NULL)
7483 * @bssid: the desired BSSID (or %NULL)
7484 * @ssid: the desired SSID (or %NULL)
7485 * @ssid_len: length of the SSID (or 0)
7486 * @bss_type: type of BSS, see &enum ieee80211_bss_type
7487 * @privacy: privacy filter, see &enum ieee80211_privacy
7488 *
7489 * This version implies regular usage, %NL80211_BSS_USE_FOR_NORMAL.
7490 *
7491 * Return: Reference-counted BSS on success. %NULL on error.
7492 */
7493static inline struct cfg80211_bss *
7494cfg80211_get_bss(struct wiphy *wiphy, struct ieee80211_channel *channel,
7495 const u8 *bssid, const u8 *ssid, size_t ssid_len,
7496 enum ieee80211_bss_type bss_type,
7497 enum ieee80211_privacy privacy)
7498{
7499 return __cfg80211_get_bss(wiphy, channel, bssid, ssid, ssid_len,
7500 bss_type, privacy,
7501 NL80211_BSS_USE_FOR_NORMAL);
7502}
7503
7504static inline struct cfg80211_bss *
7505cfg80211_get_ibss(struct wiphy *wiphy,
7506 struct ieee80211_channel *channel,
7507 const u8 *ssid, size_t ssid_len)
7508{
7509 return cfg80211_get_bss(wiphy, channel, NULL, ssid, ssid_len,
7510 IEEE80211_BSS_TYPE_IBSS,
7511 IEEE80211_PRIVACY_ANY);
7512}
7513
7514/**
7515 * cfg80211_ref_bss - reference BSS struct
7516 * @wiphy: the wiphy this BSS struct belongs to
7517 * @bss: the BSS struct to reference
7518 *
7519 * Increments the refcount of the given BSS struct.
7520 */
7521void cfg80211_ref_bss(struct wiphy *wiphy, struct cfg80211_bss *bss);
7522
7523/**
7524 * cfg80211_put_bss - unref BSS struct
7525 * @wiphy: the wiphy this BSS struct belongs to
7526 * @bss: the BSS struct
7527 *
7528 * Decrements the refcount of the given BSS struct.
7529 */
7530void cfg80211_put_bss(struct wiphy *wiphy, struct cfg80211_bss *bss);
7531
7532/**
7533 * cfg80211_unlink_bss - unlink BSS from internal data structures
7534 * @wiphy: the wiphy
7535 * @bss: the bss to remove
7536 *
7537 * This function removes the given BSS from the internal data structures
7538 * thereby making it no longer show up in scan results etc. Use this
7539 * function when you detect a BSS is gone. Normally BSSes will also time
7540 * out, so it is not necessary to use this function at all.
7541 */
7542void cfg80211_unlink_bss(struct wiphy *wiphy, struct cfg80211_bss *bss);
7543
7544/**
7545 * cfg80211_bss_iter - iterate all BSS entries
7546 *
7547 * This function iterates over the BSS entries associated with the given wiphy
7548 * and calls the callback for the iterated BSS. The iterator function is not
7549 * allowed to call functions that might modify the internal state of the BSS DB.
7550 *
7551 * @wiphy: the wiphy
7552 * @chandef: if given, the iterator function will be called only if the channel
7553 * of the currently iterated BSS is a subset of the given channel.
7554 * @iter: the iterator function to call
7555 * @iter_data: an argument to the iterator function
7556 */
7557void cfg80211_bss_iter(struct wiphy *wiphy,
7558 struct cfg80211_chan_def *chandef,
7559 void (*iter)(struct wiphy *wiphy,
7560 struct cfg80211_bss *bss,
7561 void *data),
7562 void *iter_data);
7563
7564/**
7565 * cfg80211_rx_mlme_mgmt - notification of processed MLME management frame
7566 * @dev: network device
7567 * @buf: authentication frame (header + body)
7568 * @len: length of the frame data
7569 *
7570 * This function is called whenever an authentication, disassociation or
7571 * deauthentication frame has been received and processed in station mode.
7572 * After being asked to authenticate via cfg80211_ops::auth() the driver must
7573 * call either this function or cfg80211_auth_timeout().
7574 * After being asked to associate via cfg80211_ops::assoc() the driver must
7575 * call either this function or cfg80211_auth_timeout().
7576 * While connected, the driver must calls this for received and processed
7577 * disassociation and deauthentication frames. If the frame couldn't be used
7578 * because it was unprotected, the driver must call the function
7579 * cfg80211_rx_unprot_mlme_mgmt() instead.
7580 *
7581 * This function may sleep. The caller must hold the corresponding wdev's mutex.
7582 */
7583void cfg80211_rx_mlme_mgmt(struct net_device *dev, const u8 *buf, size_t len);
7584
7585/**
7586 * cfg80211_auth_timeout - notification of timed out authentication
7587 * @dev: network device
7588 * @addr: The MAC address of the device with which the authentication timed out
7589 *
7590 * This function may sleep. The caller must hold the corresponding wdev's
7591 * mutex.
7592 */
7593void cfg80211_auth_timeout(struct net_device *dev, const u8 *addr);
7594
7595/**
7596 * struct cfg80211_rx_assoc_resp_data - association response data
7597 * @buf: (Re)Association Response frame (header + body)
7598 * @len: length of the frame data
7599 * @uapsd_queues: bitmap of queues configured for uapsd. Same format
7600 * as the AC bitmap in the QoS info field
7601 * @req_ies: information elements from the (Re)Association Request frame
7602 * @req_ies_len: length of req_ies data
7603 * @ap_mld_addr: AP MLD address (in case of MLO)
7604 * @links: per-link information indexed by link ID, use links[0] for
7605 * non-MLO connections
7606 * @links.bss: the BSS that association was requested with, ownership of the
7607 * pointer moves to cfg80211 in the call to cfg80211_rx_assoc_resp()
7608 * @links.status: Set this (along with a BSS pointer) for links that
7609 * were rejected by the AP.
7610 */
7611struct cfg80211_rx_assoc_resp_data {
7612 const u8 *buf;
7613 size_t len;
7614 const u8 *req_ies;
7615 size_t req_ies_len;
7616 int uapsd_queues;
7617 const u8 *ap_mld_addr;
7618 struct {
7619 u8 addr[ETH_ALEN] __aligned(2);
7620 struct cfg80211_bss *bss;
7621 u16 status;
7622 } links[IEEE80211_MLD_MAX_NUM_LINKS];
7623};
7624
7625/**
7626 * cfg80211_rx_assoc_resp - notification of processed association response
7627 * @dev: network device
7628 * @data: association response data, &struct cfg80211_rx_assoc_resp_data
7629 *
7630 * After being asked to associate via cfg80211_ops::assoc() the driver must
7631 * call either this function or cfg80211_auth_timeout().
7632 *
7633 * This function may sleep. The caller must hold the corresponding wdev's mutex.
7634 */
7635void cfg80211_rx_assoc_resp(struct net_device *dev,
7636 const struct cfg80211_rx_assoc_resp_data *data);
7637
7638/**
7639 * struct cfg80211_assoc_failure - association failure data
7640 * @ap_mld_addr: AP MLD address, or %NULL
7641 * @bss: list of BSSes, must use entry 0 for non-MLO connections
7642 * (@ap_mld_addr is %NULL)
7643 * @timeout: indicates the association failed due to timeout, otherwise
7644 * the association was abandoned for a reason reported through some
7645 * other API (e.g. deauth RX)
7646 */
7647struct cfg80211_assoc_failure {
7648 const u8 *ap_mld_addr;
7649 struct cfg80211_bss *bss[IEEE80211_MLD_MAX_NUM_LINKS];
7650 bool timeout;
7651};
7652
7653/**
7654 * cfg80211_assoc_failure - notification of association failure
7655 * @dev: network device
7656 * @data: data describing the association failure
7657 *
7658 * This function may sleep. The caller must hold the corresponding wdev's mutex.
7659 */
7660void cfg80211_assoc_failure(struct net_device *dev,
7661 struct cfg80211_assoc_failure *data);
7662
7663/**
7664 * cfg80211_tx_mlme_mgmt - notification of transmitted deauth/disassoc frame
7665 * @dev: network device
7666 * @buf: 802.11 frame (header + body)
7667 * @len: length of the frame data
7668 * @reconnect: immediate reconnect is desired (include the nl80211 attribute)
7669 *
7670 * This function is called whenever deauthentication has been processed in
7671 * station mode. This includes both received deauthentication frames and
7672 * locally generated ones. This function may sleep. The caller must hold the
7673 * corresponding wdev's mutex.
7674 */
7675void cfg80211_tx_mlme_mgmt(struct net_device *dev, const u8 *buf, size_t len,
7676 bool reconnect);
7677
7678/**
7679 * cfg80211_rx_unprot_mlme_mgmt - notification of unprotected mlme mgmt frame
7680 * @dev: network device
7681 * @buf: received management frame (header + body)
7682 * @len: length of the frame data
7683 *
7684 * This function is called whenever a received deauthentication or dissassoc
7685 * frame has been dropped in station mode because of MFP being used but the
7686 * frame was not protected. This is also used to notify reception of a Beacon
7687 * frame that was dropped because it did not include a valid MME MIC while
7688 * beacon protection was enabled (BIGTK configured in station mode).
7689 *
7690 * This function may sleep.
7691 */
7692void cfg80211_rx_unprot_mlme_mgmt(struct net_device *dev,
7693 const u8 *buf, size_t len);
7694
7695/**
7696 * cfg80211_michael_mic_failure - notification of Michael MIC failure (TKIP)
7697 * @dev: network device
7698 * @addr: The source MAC address of the frame
7699 * @key_type: The key type that the received frame used
7700 * @key_id: Key identifier (0..3). Can be -1 if missing.
7701 * @tsc: The TSC value of the frame that generated the MIC failure (6 octets)
7702 * @gfp: allocation flags
7703 *
7704 * This function is called whenever the local MAC detects a MIC failure in a
7705 * received frame. This matches with MLME-MICHAELMICFAILURE.indication()
7706 * primitive.
7707 */
7708void cfg80211_michael_mic_failure(struct net_device *dev, const u8 *addr,
7709 enum nl80211_key_type key_type, int key_id,
7710 const u8 *tsc, gfp_t gfp);
7711
7712/**
7713 * cfg80211_ibss_joined - notify cfg80211 that device joined an IBSS
7714 *
7715 * @dev: network device
7716 * @bssid: the BSSID of the IBSS joined
7717 * @channel: the channel of the IBSS joined
7718 * @gfp: allocation flags
7719 *
7720 * This function notifies cfg80211 that the device joined an IBSS or
7721 * switched to a different BSSID. Before this function can be called,
7722 * either a beacon has to have been received from the IBSS, or one of
7723 * the cfg80211_inform_bss{,_frame} functions must have been called
7724 * with the locally generated beacon -- this guarantees that there is
7725 * always a scan result for this IBSS. cfg80211 will handle the rest.
7726 */
7727void cfg80211_ibss_joined(struct net_device *dev, const u8 *bssid,
7728 struct ieee80211_channel *channel, gfp_t gfp);
7729
7730/**
7731 * cfg80211_notify_new_peer_candidate - notify cfg80211 of a new mesh peer
7732 * candidate
7733 *
7734 * @dev: network device
7735 * @macaddr: the MAC address of the new candidate
7736 * @ie: information elements advertised by the peer candidate
7737 * @ie_len: length of the information elements buffer
7738 * @sig_dbm: signal level in dBm
7739 * @gfp: allocation flags
7740 *
7741 * This function notifies cfg80211 that the mesh peer candidate has been
7742 * detected, most likely via a beacon or, less likely, via a probe response.
7743 * cfg80211 then sends a notification to userspace.
7744 */
7745void cfg80211_notify_new_peer_candidate(struct net_device *dev,
7746 const u8 *macaddr, const u8 *ie, u8 ie_len,
7747 int sig_dbm, gfp_t gfp);
7748
7749/**
7750 * DOC: RFkill integration
7751 *
7752 * RFkill integration in cfg80211 is almost invisible to drivers,
7753 * as cfg80211 automatically registers an rfkill instance for each
7754 * wireless device it knows about. Soft kill is also translated
7755 * into disconnecting and turning all interfaces off. Drivers are
7756 * expected to turn off the device when all interfaces are down.
7757 *
7758 * However, devices may have a hard RFkill line, in which case they
7759 * also need to interact with the rfkill subsystem, via cfg80211.
7760 * They can do this with a few helper functions documented here.
7761 */
7762
7763/**
7764 * wiphy_rfkill_set_hw_state_reason - notify cfg80211 about hw block state
7765 * @wiphy: the wiphy
7766 * @blocked: block status
7767 * @reason: one of reasons in &enum rfkill_hard_block_reasons
7768 */
7769void wiphy_rfkill_set_hw_state_reason(struct wiphy *wiphy, bool blocked,
7770 enum rfkill_hard_block_reasons reason);
7771
7772static inline void wiphy_rfkill_set_hw_state(struct wiphy *wiphy, bool blocked)
7773{
7774 wiphy_rfkill_set_hw_state_reason(wiphy, blocked,
7775 RFKILL_HARD_BLOCK_SIGNAL);
7776}
7777
7778/**
7779 * wiphy_rfkill_start_polling - start polling rfkill
7780 * @wiphy: the wiphy
7781 */
7782void wiphy_rfkill_start_polling(struct wiphy *wiphy);
7783
7784/**
7785 * wiphy_rfkill_stop_polling - stop polling rfkill
7786 * @wiphy: the wiphy
7787 */
7788static inline void wiphy_rfkill_stop_polling(struct wiphy *wiphy)
7789{
7790 rfkill_pause_polling(wiphy->rfkill);
7791}
7792
7793/**
7794 * DOC: Vendor commands
7795 *
7796 * Occasionally, there are special protocol or firmware features that
7797 * can't be implemented very openly. For this and similar cases, the
7798 * vendor command functionality allows implementing the features with
7799 * (typically closed-source) userspace and firmware, using nl80211 as
7800 * the configuration mechanism.
7801 *
7802 * A driver supporting vendor commands must register them as an array
7803 * in struct wiphy, with handlers for each one. Each command has an
7804 * OUI and sub command ID to identify it.
7805 *
7806 * Note that this feature should not be (ab)used to implement protocol
7807 * features that could openly be shared across drivers. In particular,
7808 * it must never be required to use vendor commands to implement any
7809 * "normal" functionality that higher-level userspace like connection
7810 * managers etc. need.
7811 */
7812
7813struct sk_buff *__cfg80211_alloc_reply_skb(struct wiphy *wiphy,
7814 enum nl80211_commands cmd,
7815 enum nl80211_attrs attr,
7816 int approxlen);
7817
7818struct sk_buff *__cfg80211_alloc_event_skb(struct wiphy *wiphy,
7819 struct wireless_dev *wdev,
7820 enum nl80211_commands cmd,
7821 enum nl80211_attrs attr,
7822 unsigned int portid,
7823 int vendor_event_idx,
7824 int approxlen, gfp_t gfp);
7825
7826void __cfg80211_send_event_skb(struct sk_buff *skb, gfp_t gfp);
7827
7828/**
7829 * cfg80211_vendor_cmd_alloc_reply_skb - allocate vendor command reply
7830 * @wiphy: the wiphy
7831 * @approxlen: an upper bound of the length of the data that will
7832 * be put into the skb
7833 *
7834 * This function allocates and pre-fills an skb for a reply to
7835 * a vendor command. Since it is intended for a reply, calling
7836 * it outside of a vendor command's doit() operation is invalid.
7837 *
7838 * The returned skb is pre-filled with some identifying data in
7839 * a way that any data that is put into the skb (with skb_put(),
7840 * nla_put() or similar) will end up being within the
7841 * %NL80211_ATTR_VENDOR_DATA attribute, so all that needs to be done
7842 * with the skb is adding data for the corresponding userspace tool
7843 * which can then read that data out of the vendor data attribute.
7844 * You must not modify the skb in any other way.
7845 *
7846 * When done, call cfg80211_vendor_cmd_reply() with the skb and return
7847 * its error code as the result of the doit() operation.
7848 *
7849 * Return: An allocated and pre-filled skb. %NULL if any errors happen.
7850 */
7851static inline struct sk_buff *
7852cfg80211_vendor_cmd_alloc_reply_skb(struct wiphy *wiphy, int approxlen)
7853{
7854 return __cfg80211_alloc_reply_skb(wiphy, NL80211_CMD_VENDOR,
7855 NL80211_ATTR_VENDOR_DATA, approxlen);
7856}
7857
7858/**
7859 * cfg80211_vendor_cmd_reply - send the reply skb
7860 * @skb: The skb, must have been allocated with
7861 * cfg80211_vendor_cmd_alloc_reply_skb()
7862 *
7863 * Since calling this function will usually be the last thing
7864 * before returning from the vendor command doit() you should
7865 * return the error code. Note that this function consumes the
7866 * skb regardless of the return value.
7867 *
7868 * Return: An error code or 0 on success.
7869 */
7870int cfg80211_vendor_cmd_reply(struct sk_buff *skb);
7871
7872/**
7873 * cfg80211_vendor_cmd_get_sender - get the current sender netlink ID
7874 * @wiphy: the wiphy
7875 *
7876 * Return: the current netlink port ID in a vendor command handler.
7877 *
7878 * Context: May only be called from a vendor command handler
7879 */
7880unsigned int cfg80211_vendor_cmd_get_sender(struct wiphy *wiphy);
7881
7882/**
7883 * cfg80211_vendor_event_alloc - allocate vendor-specific event skb
7884 * @wiphy: the wiphy
7885 * @wdev: the wireless device
7886 * @event_idx: index of the vendor event in the wiphy's vendor_events
7887 * @approxlen: an upper bound of the length of the data that will
7888 * be put into the skb
7889 * @gfp: allocation flags
7890 *
7891 * This function allocates and pre-fills an skb for an event on the
7892 * vendor-specific multicast group.
7893 *
7894 * If wdev != NULL, both the ifindex and identifier of the specified
7895 * wireless device are added to the event message before the vendor data
7896 * attribute.
7897 *
7898 * When done filling the skb, call cfg80211_vendor_event() with the
7899 * skb to send the event.
7900 *
7901 * Return: An allocated and pre-filled skb. %NULL if any errors happen.
7902 */
7903static inline struct sk_buff *
7904cfg80211_vendor_event_alloc(struct wiphy *wiphy, struct wireless_dev *wdev,
7905 int approxlen, int event_idx, gfp_t gfp)
7906{
7907 return __cfg80211_alloc_event_skb(wiphy, wdev, NL80211_CMD_VENDOR,
7908 NL80211_ATTR_VENDOR_DATA,
7909 0, event_idx, approxlen, gfp);
7910}
7911
7912/**
7913 * cfg80211_vendor_event_alloc_ucast - alloc unicast vendor-specific event skb
7914 * @wiphy: the wiphy
7915 * @wdev: the wireless device
7916 * @event_idx: index of the vendor event in the wiphy's vendor_events
7917 * @portid: port ID of the receiver
7918 * @approxlen: an upper bound of the length of the data that will
7919 * be put into the skb
7920 * @gfp: allocation flags
7921 *
7922 * This function allocates and pre-fills an skb for an event to send to
7923 * a specific (userland) socket. This socket would previously have been
7924 * obtained by cfg80211_vendor_cmd_get_sender(), and the caller MUST take
7925 * care to register a netlink notifier to see when the socket closes.
7926 *
7927 * If wdev != NULL, both the ifindex and identifier of the specified
7928 * wireless device are added to the event message before the vendor data
7929 * attribute.
7930 *
7931 * When done filling the skb, call cfg80211_vendor_event() with the
7932 * skb to send the event.
7933 *
7934 * Return: An allocated and pre-filled skb. %NULL if any errors happen.
7935 */
7936static inline struct sk_buff *
7937cfg80211_vendor_event_alloc_ucast(struct wiphy *wiphy,
7938 struct wireless_dev *wdev,
7939 unsigned int portid, int approxlen,
7940 int event_idx, gfp_t gfp)
7941{
7942 return __cfg80211_alloc_event_skb(wiphy, wdev, NL80211_CMD_VENDOR,
7943 NL80211_ATTR_VENDOR_DATA,
7944 portid, event_idx, approxlen, gfp);
7945}
7946
7947/**
7948 * cfg80211_vendor_event - send the event
7949 * @skb: The skb, must have been allocated with cfg80211_vendor_event_alloc()
7950 * @gfp: allocation flags
7951 *
7952 * This function sends the given @skb, which must have been allocated
7953 * by cfg80211_vendor_event_alloc(), as an event. It always consumes it.
7954 */
7955static inline void cfg80211_vendor_event(struct sk_buff *skb, gfp_t gfp)
7956{
7957 __cfg80211_send_event_skb(skb, gfp);
7958}
7959
7960#ifdef CONFIG_NL80211_TESTMODE
7961/**
7962 * DOC: Test mode
7963 *
7964 * Test mode is a set of utility functions to allow drivers to
7965 * interact with driver-specific tools to aid, for instance,
7966 * factory programming.
7967 *
7968 * This chapter describes how drivers interact with it. For more
7969 * information see the nl80211 book's chapter on it.
7970 */
7971
7972/**
7973 * cfg80211_testmode_alloc_reply_skb - allocate testmode reply
7974 * @wiphy: the wiphy
7975 * @approxlen: an upper bound of the length of the data that will
7976 * be put into the skb
7977 *
7978 * This function allocates and pre-fills an skb for a reply to
7979 * the testmode command. Since it is intended for a reply, calling
7980 * it outside of the @testmode_cmd operation is invalid.
7981 *
7982 * The returned skb is pre-filled with the wiphy index and set up in
7983 * a way that any data that is put into the skb (with skb_put(),
7984 * nla_put() or similar) will end up being within the
7985 * %NL80211_ATTR_TESTDATA attribute, so all that needs to be done
7986 * with the skb is adding data for the corresponding userspace tool
7987 * which can then read that data out of the testdata attribute. You
7988 * must not modify the skb in any other way.
7989 *
7990 * When done, call cfg80211_testmode_reply() with the skb and return
7991 * its error code as the result of the @testmode_cmd operation.
7992 *
7993 * Return: An allocated and pre-filled skb. %NULL if any errors happen.
7994 */
7995static inline struct sk_buff *
7996cfg80211_testmode_alloc_reply_skb(struct wiphy *wiphy, int approxlen)
7997{
7998 return __cfg80211_alloc_reply_skb(wiphy, NL80211_CMD_TESTMODE,
7999 NL80211_ATTR_TESTDATA, approxlen);
8000}
8001
8002/**
8003 * cfg80211_testmode_reply - send the reply skb
8004 * @skb: The skb, must have been allocated with
8005 * cfg80211_testmode_alloc_reply_skb()
8006 *
8007 * Since calling this function will usually be the last thing
8008 * before returning from the @testmode_cmd you should return
8009 * the error code. Note that this function consumes the skb
8010 * regardless of the return value.
8011 *
8012 * Return: An error code or 0 on success.
8013 */
8014static inline int cfg80211_testmode_reply(struct sk_buff *skb)
8015{
8016 return cfg80211_vendor_cmd_reply(skb);
8017}
8018
8019/**
8020 * cfg80211_testmode_alloc_event_skb - allocate testmode event
8021 * @wiphy: the wiphy
8022 * @approxlen: an upper bound of the length of the data that will
8023 * be put into the skb
8024 * @gfp: allocation flags
8025 *
8026 * This function allocates and pre-fills an skb for an event on the
8027 * testmode multicast group.
8028 *
8029 * The returned skb is set up in the same way as with
8030 * cfg80211_testmode_alloc_reply_skb() but prepared for an event. As
8031 * there, you should simply add data to it that will then end up in the
8032 * %NL80211_ATTR_TESTDATA attribute. Again, you must not modify the skb
8033 * in any other way.
8034 *
8035 * When done filling the skb, call cfg80211_testmode_event() with the
8036 * skb to send the event.
8037 *
8038 * Return: An allocated and pre-filled skb. %NULL if any errors happen.
8039 */
8040static inline struct sk_buff *
8041cfg80211_testmode_alloc_event_skb(struct wiphy *wiphy, int approxlen, gfp_t gfp)
8042{
8043 return __cfg80211_alloc_event_skb(wiphy, NULL, NL80211_CMD_TESTMODE,
8044 NL80211_ATTR_TESTDATA, 0, -1,
8045 approxlen, gfp);
8046}
8047
8048/**
8049 * cfg80211_testmode_event - send the event
8050 * @skb: The skb, must have been allocated with
8051 * cfg80211_testmode_alloc_event_skb()
8052 * @gfp: allocation flags
8053 *
8054 * This function sends the given @skb, which must have been allocated
8055 * by cfg80211_testmode_alloc_event_skb(), as an event. It always
8056 * consumes it.
8057 */
8058static inline void cfg80211_testmode_event(struct sk_buff *skb, gfp_t gfp)
8059{
8060 __cfg80211_send_event_skb(skb, gfp);
8061}
8062
8063#define CFG80211_TESTMODE_CMD(cmd) .testmode_cmd = (cmd),
8064#define CFG80211_TESTMODE_DUMP(cmd) .testmode_dump = (cmd),
8065#else
8066#define CFG80211_TESTMODE_CMD(cmd)
8067#define CFG80211_TESTMODE_DUMP(cmd)
8068#endif
8069
8070/**
8071 * struct cfg80211_fils_resp_params - FILS connection response params
8072 * @kek: KEK derived from a successful FILS connection (may be %NULL)
8073 * @kek_len: Length of @fils_kek in octets
8074 * @update_erp_next_seq_num: Boolean value to specify whether the value in
8075 * @erp_next_seq_num is valid.
8076 * @erp_next_seq_num: The next sequence number to use in ERP message in
8077 * FILS Authentication. This value should be specified irrespective of the
8078 * status for a FILS connection.
8079 * @pmk: A new PMK if derived from a successful FILS connection (may be %NULL).
8080 * @pmk_len: Length of @pmk in octets
8081 * @pmkid: A new PMKID if derived from a successful FILS connection or the PMKID
8082 * used for this FILS connection (may be %NULL).
8083 */
8084struct cfg80211_fils_resp_params {
8085 const u8 *kek;
8086 size_t kek_len;
8087 bool update_erp_next_seq_num;
8088 u16 erp_next_seq_num;
8089 const u8 *pmk;
8090 size_t pmk_len;
8091 const u8 *pmkid;
8092};
8093
8094/**
8095 * struct cfg80211_connect_resp_params - Connection response params
8096 * @status: Status code, %WLAN_STATUS_SUCCESS for successful connection, use
8097 * %WLAN_STATUS_UNSPECIFIED_FAILURE if your device cannot give you
8098 * the real status code for failures. If this call is used to report a
8099 * failure due to a timeout (e.g., not receiving an Authentication frame
8100 * from the AP) instead of an explicit rejection by the AP, -1 is used to
8101 * indicate that this is a failure, but without a status code.
8102 * @timeout_reason is used to report the reason for the timeout in that
8103 * case.
8104 * @req_ie: Association request IEs (may be %NULL)
8105 * @req_ie_len: Association request IEs length
8106 * @resp_ie: Association response IEs (may be %NULL)
8107 * @resp_ie_len: Association response IEs length
8108 * @fils: FILS connection response parameters.
8109 * @timeout_reason: Reason for connection timeout. This is used when the
8110 * connection fails due to a timeout instead of an explicit rejection from
8111 * the AP. %NL80211_TIMEOUT_UNSPECIFIED is used when the timeout reason is
8112 * not known. This value is used only if @status < 0 to indicate that the
8113 * failure is due to a timeout and not due to explicit rejection by the AP.
8114 * This value is ignored in other cases (@status >= 0).
8115 * @valid_links: For MLO connection, BIT mask of the valid link ids. Otherwise
8116 * zero.
8117 * @ap_mld_addr: For MLO connection, MLD address of the AP. Otherwise %NULL.
8118 * @links : For MLO connection, contains link info for the valid links indicated
8119 * using @valid_links. For non-MLO connection, links[0] contains the
8120 * connected AP info.
8121 * @links.addr: For MLO connection, MAC address of the STA link. Otherwise
8122 * %NULL.
8123 * @links.bssid: For MLO connection, MAC address of the AP link. For non-MLO
8124 * connection, links[0].bssid points to the BSSID of the AP (may be %NULL).
8125 * @links.bss: For MLO connection, entry of bss to which STA link is connected.
8126 * For non-MLO connection, links[0].bss points to entry of bss to which STA
8127 * is connected. It can be obtained through cfg80211_get_bss() (may be
8128 * %NULL). It is recommended to store the bss from the connect_request and
8129 * hold a reference to it and return through this param to avoid a warning
8130 * if the bss is expired during the connection, esp. for those drivers
8131 * implementing connect op. Only one parameter among @bssid and @bss needs
8132 * to be specified.
8133 * @links.status: per-link status code, to report a status code that's not
8134 * %WLAN_STATUS_SUCCESS for a given link, it must also be in the
8135 * @valid_links bitmap and may have a BSS pointer (which is then released)
8136 */
8137struct cfg80211_connect_resp_params {
8138 int status;
8139 const u8 *req_ie;
8140 size_t req_ie_len;
8141 const u8 *resp_ie;
8142 size_t resp_ie_len;
8143 struct cfg80211_fils_resp_params fils;
8144 enum nl80211_timeout_reason timeout_reason;
8145
8146 const u8 *ap_mld_addr;
8147 u16 valid_links;
8148 struct {
8149 const u8 *addr;
8150 const u8 *bssid;
8151 struct cfg80211_bss *bss;
8152 u16 status;
8153 } links[IEEE80211_MLD_MAX_NUM_LINKS];
8154};
8155
8156/**
8157 * cfg80211_connect_done - notify cfg80211 of connection result
8158 *
8159 * @dev: network device
8160 * @params: connection response parameters
8161 * @gfp: allocation flags
8162 *
8163 * It should be called by the underlying driver once execution of the connection
8164 * request from connect() has been completed. This is similar to
8165 * cfg80211_connect_bss(), but takes a structure pointer for connection response
8166 * parameters. Only one of the functions among cfg80211_connect_bss(),
8167 * cfg80211_connect_result(), cfg80211_connect_timeout(),
8168 * and cfg80211_connect_done() should be called.
8169 */
8170void cfg80211_connect_done(struct net_device *dev,
8171 struct cfg80211_connect_resp_params *params,
8172 gfp_t gfp);
8173
8174/**
8175 * cfg80211_connect_bss - notify cfg80211 of connection result
8176 *
8177 * @dev: network device
8178 * @bssid: the BSSID of the AP
8179 * @bss: Entry of bss to which STA got connected to, can be obtained through
8180 * cfg80211_get_bss() (may be %NULL). But it is recommended to store the
8181 * bss from the connect_request and hold a reference to it and return
8182 * through this param to avoid a warning if the bss is expired during the
8183 * connection, esp. for those drivers implementing connect op.
8184 * Only one parameter among @bssid and @bss needs to be specified.
8185 * @req_ie: association request IEs (maybe be %NULL)
8186 * @req_ie_len: association request IEs length
8187 * @resp_ie: association response IEs (may be %NULL)
8188 * @resp_ie_len: assoc response IEs length
8189 * @status: status code, %WLAN_STATUS_SUCCESS for successful connection, use
8190 * %WLAN_STATUS_UNSPECIFIED_FAILURE if your device cannot give you
8191 * the real status code for failures. If this call is used to report a
8192 * failure due to a timeout (e.g., not receiving an Authentication frame
8193 * from the AP) instead of an explicit rejection by the AP, -1 is used to
8194 * indicate that this is a failure, but without a status code.
8195 * @timeout_reason is used to report the reason for the timeout in that
8196 * case.
8197 * @gfp: allocation flags
8198 * @timeout_reason: reason for connection timeout. This is used when the
8199 * connection fails due to a timeout instead of an explicit rejection from
8200 * the AP. %NL80211_TIMEOUT_UNSPECIFIED is used when the timeout reason is
8201 * not known. This value is used only if @status < 0 to indicate that the
8202 * failure is due to a timeout and not due to explicit rejection by the AP.
8203 * This value is ignored in other cases (@status >= 0).
8204 *
8205 * It should be called by the underlying driver once execution of the connection
8206 * request from connect() has been completed. This is similar to
8207 * cfg80211_connect_result(), but with the option of identifying the exact bss
8208 * entry for the connection. Only one of the functions among
8209 * cfg80211_connect_bss(), cfg80211_connect_result(),
8210 * cfg80211_connect_timeout(), and cfg80211_connect_done() should be called.
8211 */
8212static inline void
8213cfg80211_connect_bss(struct net_device *dev, const u8 *bssid,
8214 struct cfg80211_bss *bss, const u8 *req_ie,
8215 size_t req_ie_len, const u8 *resp_ie,
8216 size_t resp_ie_len, int status, gfp_t gfp,
8217 enum nl80211_timeout_reason timeout_reason)
8218{
8219 struct cfg80211_connect_resp_params params;
8220
8221 memset(¶ms, 0, sizeof(params));
8222 params.status = status;
8223 params.links[0].bssid = bssid;
8224 params.links[0].bss = bss;
8225 params.req_ie = req_ie;
8226 params.req_ie_len = req_ie_len;
8227 params.resp_ie = resp_ie;
8228 params.resp_ie_len = resp_ie_len;
8229 params.timeout_reason = timeout_reason;
8230
8231 cfg80211_connect_done(dev, ¶ms, gfp);
8232}
8233
8234/**
8235 * cfg80211_connect_result - notify cfg80211 of connection result
8236 *
8237 * @dev: network device
8238 * @bssid: the BSSID of the AP
8239 * @req_ie: association request IEs (maybe be %NULL)
8240 * @req_ie_len: association request IEs length
8241 * @resp_ie: association response IEs (may be %NULL)
8242 * @resp_ie_len: assoc response IEs length
8243 * @status: status code, %WLAN_STATUS_SUCCESS for successful connection, use
8244 * %WLAN_STATUS_UNSPECIFIED_FAILURE if your device cannot give you
8245 * the real status code for failures.
8246 * @gfp: allocation flags
8247 *
8248 * It should be called by the underlying driver once execution of the connection
8249 * request from connect() has been completed. This is similar to
8250 * cfg80211_connect_bss() which allows the exact bss entry to be specified. Only
8251 * one of the functions among cfg80211_connect_bss(), cfg80211_connect_result(),
8252 * cfg80211_connect_timeout(), and cfg80211_connect_done() should be called.
8253 */
8254static inline void
8255cfg80211_connect_result(struct net_device *dev, const u8 *bssid,
8256 const u8 *req_ie, size_t req_ie_len,
8257 const u8 *resp_ie, size_t resp_ie_len,
8258 u16 status, gfp_t gfp)
8259{
8260 cfg80211_connect_bss(dev, bssid, NULL, req_ie, req_ie_len, resp_ie,
8261 resp_ie_len, status, gfp,
8262 NL80211_TIMEOUT_UNSPECIFIED);
8263}
8264
8265/**
8266 * cfg80211_connect_timeout - notify cfg80211 of connection timeout
8267 *
8268 * @dev: network device
8269 * @bssid: the BSSID of the AP
8270 * @req_ie: association request IEs (maybe be %NULL)
8271 * @req_ie_len: association request IEs length
8272 * @gfp: allocation flags
8273 * @timeout_reason: reason for connection timeout.
8274 *
8275 * It should be called by the underlying driver whenever connect() has failed
8276 * in a sequence where no explicit authentication/association rejection was
8277 * received from the AP. This could happen, e.g., due to not being able to send
8278 * out the Authentication or Association Request frame or timing out while
8279 * waiting for the response. Only one of the functions among
8280 * cfg80211_connect_bss(), cfg80211_connect_result(),
8281 * cfg80211_connect_timeout(), and cfg80211_connect_done() should be called.
8282 */
8283static inline void
8284cfg80211_connect_timeout(struct net_device *dev, const u8 *bssid,
8285 const u8 *req_ie, size_t req_ie_len, gfp_t gfp,
8286 enum nl80211_timeout_reason timeout_reason)
8287{
8288 cfg80211_connect_bss(dev, bssid, NULL, req_ie, req_ie_len, NULL, 0, -1,
8289 gfp, timeout_reason);
8290}
8291
8292/**
8293 * struct cfg80211_roam_info - driver initiated roaming information
8294 *
8295 * @req_ie: association request IEs (maybe be %NULL)
8296 * @req_ie_len: association request IEs length
8297 * @resp_ie: association response IEs (may be %NULL)
8298 * @resp_ie_len: assoc response IEs length
8299 * @fils: FILS related roaming information.
8300 * @valid_links: For MLO roaming, BIT mask of the new valid links is set.
8301 * Otherwise zero.
8302 * @ap_mld_addr: For MLO roaming, MLD address of the new AP. Otherwise %NULL.
8303 * @links : For MLO roaming, contains new link info for the valid links set in
8304 * @valid_links. For non-MLO roaming, links[0] contains the new AP info.
8305 * @links.addr: For MLO roaming, MAC address of the STA link. Otherwise %NULL.
8306 * @links.bssid: For MLO roaming, MAC address of the new AP link. For non-MLO
8307 * roaming, links[0].bssid points to the BSSID of the new AP. May be
8308 * %NULL if %links.bss is set.
8309 * @links.channel: the channel of the new AP.
8310 * @links.bss: For MLO roaming, entry of new bss to which STA link got
8311 * roamed. For non-MLO roaming, links[0].bss points to entry of bss to
8312 * which STA got roamed (may be %NULL if %links.bssid is set)
8313 */
8314struct cfg80211_roam_info {
8315 const u8 *req_ie;
8316 size_t req_ie_len;
8317 const u8 *resp_ie;
8318 size_t resp_ie_len;
8319 struct cfg80211_fils_resp_params fils;
8320
8321 const u8 *ap_mld_addr;
8322 u16 valid_links;
8323 struct {
8324 const u8 *addr;
8325 const u8 *bssid;
8326 struct ieee80211_channel *channel;
8327 struct cfg80211_bss *bss;
8328 } links[IEEE80211_MLD_MAX_NUM_LINKS];
8329};
8330
8331/**
8332 * cfg80211_roamed - notify cfg80211 of roaming
8333 *
8334 * @dev: network device
8335 * @info: information about the new BSS. struct &cfg80211_roam_info.
8336 * @gfp: allocation flags
8337 *
8338 * This function may be called with the driver passing either the BSSID of the
8339 * new AP or passing the bss entry to avoid a race in timeout of the bss entry.
8340 * It should be called by the underlying driver whenever it roamed from one AP
8341 * to another while connected. Drivers which have roaming implemented in
8342 * firmware should pass the bss entry to avoid a race in bss entry timeout where
8343 * the bss entry of the new AP is seen in the driver, but gets timed out by the
8344 * time it is accessed in __cfg80211_roamed() due to delay in scheduling
8345 * rdev->event_work. In case of any failures, the reference is released
8346 * either in cfg80211_roamed() or in __cfg80211_romed(), Otherwise, it will be
8347 * released while disconnecting from the current bss.
8348 */
8349void cfg80211_roamed(struct net_device *dev, struct cfg80211_roam_info *info,
8350 gfp_t gfp);
8351
8352/**
8353 * cfg80211_port_authorized - notify cfg80211 of successful security association
8354 *
8355 * @dev: network device
8356 * @peer_addr: BSSID of the AP/P2P GO in case of STA/GC or STA/GC MAC address
8357 * in case of AP/P2P GO
8358 * @td_bitmap: transition disable policy
8359 * @td_bitmap_len: Length of transition disable policy
8360 * @gfp: allocation flags
8361 *
8362 * This function should be called by a driver that supports 4 way handshake
8363 * offload after a security association was successfully established (i.e.,
8364 * the 4 way handshake was completed successfully). The call to this function
8365 * should be preceded with a call to cfg80211_connect_result(),
8366 * cfg80211_connect_done(), cfg80211_connect_bss() or cfg80211_roamed() to
8367 * indicate the 802.11 association.
8368 * This function can also be called by AP/P2P GO driver that supports
8369 * authentication offload. In this case the peer_mac passed is that of
8370 * associated STA/GC.
8371 */
8372void cfg80211_port_authorized(struct net_device *dev, const u8 *peer_addr,
8373 const u8* td_bitmap, u8 td_bitmap_len, gfp_t gfp);
8374
8375/**
8376 * cfg80211_disconnected - notify cfg80211 that connection was dropped
8377 *
8378 * @dev: network device
8379 * @ie: information elements of the deauth/disassoc frame (may be %NULL)
8380 * @ie_len: length of IEs
8381 * @reason: reason code for the disconnection, set it to 0 if unknown
8382 * @locally_generated: disconnection was requested locally
8383 * @gfp: allocation flags
8384 *
8385 * After it calls this function, the driver should enter an idle state
8386 * and not try to connect to any AP any more.
8387 */
8388void cfg80211_disconnected(struct net_device *dev, u16 reason,
8389 const u8 *ie, size_t ie_len,
8390 bool locally_generated, gfp_t gfp);
8391
8392/**
8393 * cfg80211_ready_on_channel - notification of remain_on_channel start
8394 * @wdev: wireless device
8395 * @cookie: the request cookie
8396 * @chan: The current channel (from remain_on_channel request)
8397 * @duration: Duration in milliseconds that the driver intents to remain on the
8398 * channel
8399 * @gfp: allocation flags
8400 */
8401void cfg80211_ready_on_channel(struct wireless_dev *wdev, u64 cookie,
8402 struct ieee80211_channel *chan,
8403 unsigned int duration, gfp_t gfp);
8404
8405/**
8406 * cfg80211_remain_on_channel_expired - remain_on_channel duration expired
8407 * @wdev: wireless device
8408 * @cookie: the request cookie
8409 * @chan: The current channel (from remain_on_channel request)
8410 * @gfp: allocation flags
8411 */
8412void cfg80211_remain_on_channel_expired(struct wireless_dev *wdev, u64 cookie,
8413 struct ieee80211_channel *chan,
8414 gfp_t gfp);
8415
8416/**
8417 * cfg80211_tx_mgmt_expired - tx_mgmt duration expired
8418 * @wdev: wireless device
8419 * @cookie: the requested cookie
8420 * @chan: The current channel (from tx_mgmt request)
8421 * @gfp: allocation flags
8422 */
8423void cfg80211_tx_mgmt_expired(struct wireless_dev *wdev, u64 cookie,
8424 struct ieee80211_channel *chan, gfp_t gfp);
8425
8426/**
8427 * cfg80211_sinfo_alloc_tid_stats - allocate per-tid statistics.
8428 *
8429 * @sinfo: the station information
8430 * @gfp: allocation flags
8431 *
8432 * Return: 0 on success. Non-zero on error.
8433 */
8434int cfg80211_sinfo_alloc_tid_stats(struct station_info *sinfo, gfp_t gfp);
8435
8436/**
8437 * cfg80211_sinfo_release_content - release contents of station info
8438 * @sinfo: the station information
8439 *
8440 * Releases any potentially allocated sub-information of the station
8441 * information, but not the struct itself (since it's typically on
8442 * the stack.)
8443 */
8444static inline void cfg80211_sinfo_release_content(struct station_info *sinfo)
8445{
8446 kfree(sinfo->pertid);
8447}
8448
8449/**
8450 * cfg80211_new_sta - notify userspace about station
8451 *
8452 * @dev: the netdev
8453 * @mac_addr: the station's address
8454 * @sinfo: the station information
8455 * @gfp: allocation flags
8456 */
8457void cfg80211_new_sta(struct net_device *dev, const u8 *mac_addr,
8458 struct station_info *sinfo, gfp_t gfp);
8459
8460/**
8461 * cfg80211_del_sta_sinfo - notify userspace about deletion of a station
8462 * @dev: the netdev
8463 * @mac_addr: the station's address. For MLD station, MLD address is used.
8464 * @sinfo: the station information/statistics
8465 * @gfp: allocation flags
8466 */
8467void cfg80211_del_sta_sinfo(struct net_device *dev, const u8 *mac_addr,
8468 struct station_info *sinfo, gfp_t gfp);
8469
8470/**
8471 * cfg80211_del_sta - notify userspace about deletion of a station
8472 *
8473 * @dev: the netdev
8474 * @mac_addr: the station's address. For MLD station, MLD address is used.
8475 * @gfp: allocation flags
8476 */
8477static inline void cfg80211_del_sta(struct net_device *dev,
8478 const u8 *mac_addr, gfp_t gfp)
8479{
8480 cfg80211_del_sta_sinfo(dev, mac_addr, NULL, gfp);
8481}
8482
8483/**
8484 * cfg80211_conn_failed - connection request failed notification
8485 *
8486 * @dev: the netdev
8487 * @mac_addr: the station's address
8488 * @reason: the reason for connection failure
8489 * @gfp: allocation flags
8490 *
8491 * Whenever a station tries to connect to an AP and if the station
8492 * could not connect to the AP as the AP has rejected the connection
8493 * for some reasons, this function is called.
8494 *
8495 * The reason for connection failure can be any of the value from
8496 * nl80211_connect_failed_reason enum
8497 */
8498void cfg80211_conn_failed(struct net_device *dev, const u8 *mac_addr,
8499 enum nl80211_connect_failed_reason reason,
8500 gfp_t gfp);
8501
8502/**
8503 * struct cfg80211_rx_info - received management frame info
8504 *
8505 * @freq: Frequency on which the frame was received in kHz
8506 * @sig_dbm: signal strength in dBm, or 0 if unknown
8507 * @have_link_id: indicates the frame was received on a link of
8508 * an MLD, i.e. the @link_id field is valid
8509 * @link_id: the ID of the link the frame was received on
8510 * @buf: Management frame (header + body)
8511 * @len: length of the frame data
8512 * @flags: flags, as defined in &enum nl80211_rxmgmt_flags
8513 * @rx_tstamp: Hardware timestamp of frame RX in nanoseconds
8514 * @ack_tstamp: Hardware timestamp of ack TX in nanoseconds
8515 */
8516struct cfg80211_rx_info {
8517 int freq;
8518 int sig_dbm;
8519 bool have_link_id;
8520 u8 link_id;
8521 const u8 *buf;
8522 size_t len;
8523 u32 flags;
8524 u64 rx_tstamp;
8525 u64 ack_tstamp;
8526};
8527
8528/**
8529 * cfg80211_rx_mgmt_ext - management frame notification with extended info
8530 * @wdev: wireless device receiving the frame
8531 * @info: RX info as defined in struct cfg80211_rx_info
8532 *
8533 * This function is called whenever an Action frame is received for a station
8534 * mode interface, but is not processed in kernel.
8535 *
8536 * Return: %true if a user space application has registered for this frame.
8537 * For action frames, that makes it responsible for rejecting unrecognized
8538 * action frames; %false otherwise, in which case for action frames the
8539 * driver is responsible for rejecting the frame.
8540 */
8541bool cfg80211_rx_mgmt_ext(struct wireless_dev *wdev,
8542 struct cfg80211_rx_info *info);
8543
8544/**
8545 * cfg80211_rx_mgmt_khz - notification of received, unprocessed management frame
8546 * @wdev: wireless device receiving the frame
8547 * @freq: Frequency on which the frame was received in KHz
8548 * @sig_dbm: signal strength in dBm, or 0 if unknown
8549 * @buf: Management frame (header + body)
8550 * @len: length of the frame data
8551 * @flags: flags, as defined in enum nl80211_rxmgmt_flags
8552 *
8553 * This function is called whenever an Action frame is received for a station
8554 * mode interface, but is not processed in kernel.
8555 *
8556 * Return: %true if a user space application has registered for this frame.
8557 * For action frames, that makes it responsible for rejecting unrecognized
8558 * action frames; %false otherwise, in which case for action frames the
8559 * driver is responsible for rejecting the frame.
8560 */
8561static inline bool cfg80211_rx_mgmt_khz(struct wireless_dev *wdev, int freq,
8562 int sig_dbm, const u8 *buf, size_t len,
8563 u32 flags)
8564{
8565 struct cfg80211_rx_info info = {
8566 .freq = freq,
8567 .sig_dbm = sig_dbm,
8568 .buf = buf,
8569 .len = len,
8570 .flags = flags
8571 };
8572
8573 return cfg80211_rx_mgmt_ext(wdev, &info);
8574}
8575
8576/**
8577 * cfg80211_rx_mgmt - notification of received, unprocessed management frame
8578 * @wdev: wireless device receiving the frame
8579 * @freq: Frequency on which the frame was received in MHz
8580 * @sig_dbm: signal strength in dBm, or 0 if unknown
8581 * @buf: Management frame (header + body)
8582 * @len: length of the frame data
8583 * @flags: flags, as defined in enum nl80211_rxmgmt_flags
8584 *
8585 * This function is called whenever an Action frame is received for a station
8586 * mode interface, but is not processed in kernel.
8587 *
8588 * Return: %true if a user space application has registered for this frame.
8589 * For action frames, that makes it responsible for rejecting unrecognized
8590 * action frames; %false otherwise, in which case for action frames the
8591 * driver is responsible for rejecting the frame.
8592 */
8593static inline bool cfg80211_rx_mgmt(struct wireless_dev *wdev, int freq,
8594 int sig_dbm, const u8 *buf, size_t len,
8595 u32 flags)
8596{
8597 struct cfg80211_rx_info info = {
8598 .freq = MHZ_TO_KHZ(freq),
8599 .sig_dbm = sig_dbm,
8600 .buf = buf,
8601 .len = len,
8602 .flags = flags
8603 };
8604
8605 return cfg80211_rx_mgmt_ext(wdev, &info);
8606}
8607
8608/**
8609 * struct cfg80211_tx_status - TX status for management frame information
8610 *
8611 * @cookie: Cookie returned by cfg80211_ops::mgmt_tx()
8612 * @tx_tstamp: hardware TX timestamp in nanoseconds
8613 * @ack_tstamp: hardware ack RX timestamp in nanoseconds
8614 * @buf: Management frame (header + body)
8615 * @len: length of the frame data
8616 * @ack: Whether frame was acknowledged
8617 */
8618struct cfg80211_tx_status {
8619 u64 cookie;
8620 u64 tx_tstamp;
8621 u64 ack_tstamp;
8622 const u8 *buf;
8623 size_t len;
8624 bool ack;
8625};
8626
8627/**
8628 * cfg80211_mgmt_tx_status_ext - TX status notification with extended info
8629 * @wdev: wireless device receiving the frame
8630 * @status: TX status data
8631 * @gfp: context flags
8632 *
8633 * This function is called whenever a management frame was requested to be
8634 * transmitted with cfg80211_ops::mgmt_tx() to report the TX status of the
8635 * transmission attempt with extended info.
8636 */
8637void cfg80211_mgmt_tx_status_ext(struct wireless_dev *wdev,
8638 struct cfg80211_tx_status *status, gfp_t gfp);
8639
8640/**
8641 * cfg80211_mgmt_tx_status - notification of TX status for management frame
8642 * @wdev: wireless device receiving the frame
8643 * @cookie: Cookie returned by cfg80211_ops::mgmt_tx()
8644 * @buf: Management frame (header + body)
8645 * @len: length of the frame data
8646 * @ack: Whether frame was acknowledged
8647 * @gfp: context flags
8648 *
8649 * This function is called whenever a management frame was requested to be
8650 * transmitted with cfg80211_ops::mgmt_tx() to report the TX status of the
8651 * transmission attempt.
8652 */
8653static inline void cfg80211_mgmt_tx_status(struct wireless_dev *wdev,
8654 u64 cookie, const u8 *buf,
8655 size_t len, bool ack, gfp_t gfp)
8656{
8657 struct cfg80211_tx_status status = {
8658 .cookie = cookie,
8659 .buf = buf,
8660 .len = len,
8661 .ack = ack
8662 };
8663
8664 cfg80211_mgmt_tx_status_ext(wdev, &status, gfp);
8665}
8666
8667/**
8668 * cfg80211_control_port_tx_status - notification of TX status for control
8669 * port frames
8670 * @wdev: wireless device receiving the frame
8671 * @cookie: Cookie returned by cfg80211_ops::tx_control_port()
8672 * @buf: Data frame (header + body)
8673 * @len: length of the frame data
8674 * @ack: Whether frame was acknowledged
8675 * @gfp: context flags
8676 *
8677 * This function is called whenever a control port frame was requested to be
8678 * transmitted with cfg80211_ops::tx_control_port() to report the TX status of
8679 * the transmission attempt.
8680 */
8681void cfg80211_control_port_tx_status(struct wireless_dev *wdev, u64 cookie,
8682 const u8 *buf, size_t len, bool ack,
8683 gfp_t gfp);
8684
8685/**
8686 * cfg80211_rx_control_port - notification about a received control port frame
8687 * @dev: The device the frame matched to
8688 * @skb: The skbuf with the control port frame. It is assumed that the skbuf
8689 * is 802.3 formatted (with 802.3 header). The skb can be non-linear.
8690 * This function does not take ownership of the skb, so the caller is
8691 * responsible for any cleanup. The caller must also ensure that
8692 * skb->protocol is set appropriately.
8693 * @unencrypted: Whether the frame was received unencrypted
8694 * @link_id: the link the frame was received on, -1 if not applicable or unknown
8695 *
8696 * This function is used to inform userspace about a received control port
8697 * frame. It should only be used if userspace indicated it wants to receive
8698 * control port frames over nl80211.
8699 *
8700 * The frame is the data portion of the 802.3 or 802.11 data frame with all
8701 * network layer headers removed (e.g. the raw EAPoL frame).
8702 *
8703 * Return: %true if the frame was passed to userspace
8704 */
8705bool cfg80211_rx_control_port(struct net_device *dev, struct sk_buff *skb,
8706 bool unencrypted, int link_id);
8707
8708/**
8709 * cfg80211_cqm_rssi_notify - connection quality monitoring rssi event
8710 * @dev: network device
8711 * @rssi_event: the triggered RSSI event
8712 * @rssi_level: new RSSI level value or 0 if not available
8713 * @gfp: context flags
8714 *
8715 * This function is called when a configured connection quality monitoring
8716 * rssi threshold reached event occurs.
8717 */
8718void cfg80211_cqm_rssi_notify(struct net_device *dev,
8719 enum nl80211_cqm_rssi_threshold_event rssi_event,
8720 s32 rssi_level, gfp_t gfp);
8721
8722/**
8723 * cfg80211_cqm_pktloss_notify - notify userspace about packetloss to peer
8724 * @dev: network device
8725 * @peer: peer's MAC address
8726 * @num_packets: how many packets were lost -- should be a fixed threshold
8727 * but probably no less than maybe 50, or maybe a throughput dependent
8728 * threshold (to account for temporary interference)
8729 * @gfp: context flags
8730 */
8731void cfg80211_cqm_pktloss_notify(struct net_device *dev,
8732 const u8 *peer, u32 num_packets, gfp_t gfp);
8733
8734/**
8735 * cfg80211_cqm_txe_notify - TX error rate event
8736 * @dev: network device
8737 * @peer: peer's MAC address
8738 * @num_packets: how many packets were lost
8739 * @rate: % of packets which failed transmission
8740 * @intvl: interval (in s) over which the TX failure threshold was breached.
8741 * @gfp: context flags
8742 *
8743 * Notify userspace when configured % TX failures over number of packets in a
8744 * given interval is exceeded.
8745 */
8746void cfg80211_cqm_txe_notify(struct net_device *dev, const u8 *peer,
8747 u32 num_packets, u32 rate, u32 intvl, gfp_t gfp);
8748
8749/**
8750 * cfg80211_cqm_beacon_loss_notify - beacon loss event
8751 * @dev: network device
8752 * @gfp: context flags
8753 *
8754 * Notify userspace about beacon loss from the connected AP.
8755 */
8756void cfg80211_cqm_beacon_loss_notify(struct net_device *dev, gfp_t gfp);
8757
8758/**
8759 * __cfg80211_radar_event - radar detection event
8760 * @wiphy: the wiphy
8761 * @chandef: chandef for the current channel
8762 * @offchan: the radar has been detected on the offchannel chain
8763 * @gfp: context flags
8764 *
8765 * This function is called when a radar is detected on the current chanenl.
8766 */
8767void __cfg80211_radar_event(struct wiphy *wiphy,
8768 struct cfg80211_chan_def *chandef,
8769 bool offchan, gfp_t gfp);
8770
8771static inline void
8772cfg80211_radar_event(struct wiphy *wiphy,
8773 struct cfg80211_chan_def *chandef,
8774 gfp_t gfp)
8775{
8776 __cfg80211_radar_event(wiphy, chandef, false, gfp);
8777}
8778
8779static inline void
8780cfg80211_background_radar_event(struct wiphy *wiphy,
8781 struct cfg80211_chan_def *chandef,
8782 gfp_t gfp)
8783{
8784 __cfg80211_radar_event(wiphy, chandef, true, gfp);
8785}
8786
8787/**
8788 * cfg80211_sta_opmode_change_notify - STA's ht/vht operation mode change event
8789 * @dev: network device
8790 * @mac: MAC address of a station which opmode got modified
8791 * @sta_opmode: station's current opmode value
8792 * @gfp: context flags
8793 *
8794 * Driver should call this function when station's opmode modified via action
8795 * frame.
8796 */
8797void cfg80211_sta_opmode_change_notify(struct net_device *dev, const u8 *mac,
8798 struct sta_opmode_info *sta_opmode,
8799 gfp_t gfp);
8800
8801/**
8802 * cfg80211_cac_event - Channel availability check (CAC) event
8803 * @netdev: network device
8804 * @chandef: chandef for the current channel
8805 * @event: type of event
8806 * @gfp: context flags
8807 * @link_id: valid link_id for MLO operation or 0 otherwise.
8808 *
8809 * This function is called when a Channel availability check (CAC) is finished
8810 * or aborted. This must be called to notify the completion of a CAC process,
8811 * also by full-MAC drivers.
8812 */
8813void cfg80211_cac_event(struct net_device *netdev,
8814 const struct cfg80211_chan_def *chandef,
8815 enum nl80211_radar_event event, gfp_t gfp,
8816 unsigned int link_id);
8817
8818/**
8819 * cfg80211_background_cac_abort - Channel Availability Check offchan abort event
8820 * @wiphy: the wiphy
8821 *
8822 * This function is called by the driver when a Channel Availability Check
8823 * (CAC) is aborted by a offchannel dedicated chain.
8824 */
8825void cfg80211_background_cac_abort(struct wiphy *wiphy);
8826
8827/**
8828 * cfg80211_gtk_rekey_notify - notify userspace about driver rekeying
8829 * @dev: network device
8830 * @bssid: BSSID of AP (to avoid races)
8831 * @replay_ctr: new replay counter
8832 * @gfp: allocation flags
8833 */
8834void cfg80211_gtk_rekey_notify(struct net_device *dev, const u8 *bssid,
8835 const u8 *replay_ctr, gfp_t gfp);
8836
8837/**
8838 * cfg80211_pmksa_candidate_notify - notify about PMKSA caching candidate
8839 * @dev: network device
8840 * @index: candidate index (the smaller the index, the higher the priority)
8841 * @bssid: BSSID of AP
8842 * @preauth: Whether AP advertises support for RSN pre-authentication
8843 * @gfp: allocation flags
8844 */
8845void cfg80211_pmksa_candidate_notify(struct net_device *dev, int index,
8846 const u8 *bssid, bool preauth, gfp_t gfp);
8847
8848/**
8849 * cfg80211_rx_spurious_frame - inform userspace about a spurious frame
8850 * @dev: The device the frame matched to
8851 * @addr: the transmitter address
8852 * @gfp: context flags
8853 *
8854 * This function is used in AP mode (only!) to inform userspace that
8855 * a spurious class 3 frame was received, to be able to deauth the
8856 * sender.
8857 * Return: %true if the frame was passed to userspace (or this failed
8858 * for a reason other than not having a subscription.)
8859 */
8860bool cfg80211_rx_spurious_frame(struct net_device *dev,
8861 const u8 *addr, gfp_t gfp);
8862
8863/**
8864 * cfg80211_rx_unexpected_4addr_frame - inform about unexpected WDS frame
8865 * @dev: The device the frame matched to
8866 * @addr: the transmitter address
8867 * @gfp: context flags
8868 *
8869 * This function is used in AP mode (only!) to inform userspace that
8870 * an associated station sent a 4addr frame but that wasn't expected.
8871 * It is allowed and desirable to send this event only once for each
8872 * station to avoid event flooding.
8873 * Return: %true if the frame was passed to userspace (or this failed
8874 * for a reason other than not having a subscription.)
8875 */
8876bool cfg80211_rx_unexpected_4addr_frame(struct net_device *dev,
8877 const u8 *addr, gfp_t gfp);
8878
8879/**
8880 * cfg80211_probe_status - notify userspace about probe status
8881 * @dev: the device the probe was sent on
8882 * @addr: the address of the peer
8883 * @cookie: the cookie filled in @probe_client previously
8884 * @acked: indicates whether probe was acked or not
8885 * @ack_signal: signal strength (in dBm) of the ACK frame.
8886 * @is_valid_ack_signal: indicates the ack_signal is valid or not.
8887 * @gfp: allocation flags
8888 */
8889void cfg80211_probe_status(struct net_device *dev, const u8 *addr,
8890 u64 cookie, bool acked, s32 ack_signal,
8891 bool is_valid_ack_signal, gfp_t gfp);
8892
8893/**
8894 * cfg80211_report_obss_beacon_khz - report beacon from other APs
8895 * @wiphy: The wiphy that received the beacon
8896 * @frame: the frame
8897 * @len: length of the frame
8898 * @freq: frequency the frame was received on in KHz
8899 * @sig_dbm: signal strength in dBm, or 0 if unknown
8900 *
8901 * Use this function to report to userspace when a beacon was
8902 * received. It is not useful to call this when there is no
8903 * netdev that is in AP/GO mode.
8904 */
8905void cfg80211_report_obss_beacon_khz(struct wiphy *wiphy, const u8 *frame,
8906 size_t len, int freq, int sig_dbm);
8907
8908/**
8909 * cfg80211_report_obss_beacon - report beacon from other APs
8910 * @wiphy: The wiphy that received the beacon
8911 * @frame: the frame
8912 * @len: length of the frame
8913 * @freq: frequency the frame was received on
8914 * @sig_dbm: signal strength in dBm, or 0 if unknown
8915 *
8916 * Use this function to report to userspace when a beacon was
8917 * received. It is not useful to call this when there is no
8918 * netdev that is in AP/GO mode.
8919 */
8920static inline void cfg80211_report_obss_beacon(struct wiphy *wiphy,
8921 const u8 *frame, size_t len,
8922 int freq, int sig_dbm)
8923{
8924 cfg80211_report_obss_beacon_khz(wiphy, frame, len, MHZ_TO_KHZ(freq),
8925 sig_dbm);
8926}
8927
8928/**
8929 * struct cfg80211_beaconing_check_config - beacon check configuration
8930 * @iftype: the interface type to check for
8931 * @relax: allow IR-relaxation conditions to apply (e.g. another
8932 * interface connected already on the same channel)
8933 * NOTE: If this is set, wiphy mutex must be held.
8934 * @reg_power: &enum ieee80211_ap_reg_power value indicating the
8935 * advertised/used 6 GHz regulatory power setting
8936 */
8937struct cfg80211_beaconing_check_config {
8938 enum nl80211_iftype iftype;
8939 enum ieee80211_ap_reg_power reg_power;
8940 bool relax;
8941};
8942
8943/**
8944 * cfg80211_reg_check_beaconing - check if beaconing is allowed
8945 * @wiphy: the wiphy
8946 * @chandef: the channel definition
8947 * @cfg: additional parameters for the checking
8948 *
8949 * Return: %true if there is no secondary channel or the secondary channel(s)
8950 * can be used for beaconing (i.e. is not a radar channel etc.)
8951 */
8952bool cfg80211_reg_check_beaconing(struct wiphy *wiphy,
8953 struct cfg80211_chan_def *chandef,
8954 struct cfg80211_beaconing_check_config *cfg);
8955
8956/**
8957 * cfg80211_reg_can_beacon - check if beaconing is allowed
8958 * @wiphy: the wiphy
8959 * @chandef: the channel definition
8960 * @iftype: interface type
8961 *
8962 * Return: %true if there is no secondary channel or the secondary channel(s)
8963 * can be used for beaconing (i.e. is not a radar channel etc.)
8964 */
8965static inline bool
8966cfg80211_reg_can_beacon(struct wiphy *wiphy,
8967 struct cfg80211_chan_def *chandef,
8968 enum nl80211_iftype iftype)
8969{
8970 struct cfg80211_beaconing_check_config config = {
8971 .iftype = iftype,
8972 };
8973
8974 return cfg80211_reg_check_beaconing(wiphy, chandef, &config);
8975}
8976
8977/**
8978 * cfg80211_reg_can_beacon_relax - check if beaconing is allowed with relaxation
8979 * @wiphy: the wiphy
8980 * @chandef: the channel definition
8981 * @iftype: interface type
8982 *
8983 * Return: %true if there is no secondary channel or the secondary channel(s)
8984 * can be used for beaconing (i.e. is not a radar channel etc.). This version
8985 * also checks if IR-relaxation conditions apply, to allow beaconing under
8986 * more permissive conditions.
8987 *
8988 * Context: Requires the wiphy mutex to be held.
8989 */
8990static inline bool
8991cfg80211_reg_can_beacon_relax(struct wiphy *wiphy,
8992 struct cfg80211_chan_def *chandef,
8993 enum nl80211_iftype iftype)
8994{
8995 struct cfg80211_beaconing_check_config config = {
8996 .iftype = iftype,
8997 .relax = true,
8998 };
8999
9000 return cfg80211_reg_check_beaconing(wiphy, chandef, &config);
9001}
9002
9003/**
9004 * cfg80211_ch_switch_notify - update wdev channel and notify userspace
9005 * @dev: the device which switched channels
9006 * @chandef: the new channel definition
9007 * @link_id: the link ID for MLO, must be 0 for non-MLO
9008 *
9009 * Caller must hold wiphy mutex, therefore must only be called from sleepable
9010 * driver context!
9011 */
9012void cfg80211_ch_switch_notify(struct net_device *dev,
9013 struct cfg80211_chan_def *chandef,
9014 unsigned int link_id);
9015
9016/**
9017 * cfg80211_ch_switch_started_notify - notify channel switch start
9018 * @dev: the device on which the channel switch started
9019 * @chandef: the future channel definition
9020 * @link_id: the link ID for MLO, must be 0 for non-MLO
9021 * @count: the number of TBTTs until the channel switch happens
9022 * @quiet: whether or not immediate quiet was requested by the AP
9023 *
9024 * Inform the userspace about the channel switch that has just
9025 * started, so that it can take appropriate actions (eg. starting
9026 * channel switch on other vifs), if necessary.
9027 */
9028void cfg80211_ch_switch_started_notify(struct net_device *dev,
9029 struct cfg80211_chan_def *chandef,
9030 unsigned int link_id, u8 count,
9031 bool quiet);
9032
9033/**
9034 * ieee80211_operating_class_to_band - convert operating class to band
9035 *
9036 * @operating_class: the operating class to convert
9037 * @band: band pointer to fill
9038 *
9039 * Return: %true if the conversion was successful, %false otherwise.
9040 */
9041bool ieee80211_operating_class_to_band(u8 operating_class,
9042 enum nl80211_band *band);
9043
9044/**
9045 * ieee80211_operating_class_to_chandef - convert operating class to chandef
9046 *
9047 * @operating_class: the operating class to convert
9048 * @chan: the ieee80211_channel to convert
9049 * @chandef: a pointer to the resulting chandef
9050 *
9051 * Return: %true if the conversion was successful, %false otherwise.
9052 */
9053bool ieee80211_operating_class_to_chandef(u8 operating_class,
9054 struct ieee80211_channel *chan,
9055 struct cfg80211_chan_def *chandef);
9056
9057/**
9058 * ieee80211_chandef_to_operating_class - convert chandef to operation class
9059 *
9060 * @chandef: the chandef to convert
9061 * @op_class: a pointer to the resulting operating class
9062 *
9063 * Return: %true if the conversion was successful, %false otherwise.
9064 */
9065bool ieee80211_chandef_to_operating_class(struct cfg80211_chan_def *chandef,
9066 u8 *op_class);
9067
9068/**
9069 * ieee80211_chandef_to_khz - convert chandef to frequency in KHz
9070 *
9071 * @chandef: the chandef to convert
9072 *
9073 * Return: the center frequency of chandef (1st segment) in KHz.
9074 */
9075static inline u32
9076ieee80211_chandef_to_khz(const struct cfg80211_chan_def *chandef)
9077{
9078 return MHZ_TO_KHZ(chandef->center_freq1) + chandef->freq1_offset;
9079}
9080
9081/**
9082 * cfg80211_tdls_oper_request - request userspace to perform TDLS operation
9083 * @dev: the device on which the operation is requested
9084 * @peer: the MAC address of the peer device
9085 * @oper: the requested TDLS operation (NL80211_TDLS_SETUP or
9086 * NL80211_TDLS_TEARDOWN)
9087 * @reason_code: the reason code for teardown request
9088 * @gfp: allocation flags
9089 *
9090 * This function is used to request userspace to perform TDLS operation that
9091 * requires knowledge of keys, i.e., link setup or teardown when the AP
9092 * connection uses encryption. This is optional mechanism for the driver to use
9093 * if it can automatically determine when a TDLS link could be useful (e.g.,
9094 * based on traffic and signal strength for a peer).
9095 */
9096void cfg80211_tdls_oper_request(struct net_device *dev, const u8 *peer,
9097 enum nl80211_tdls_operation oper,
9098 u16 reason_code, gfp_t gfp);
9099
9100/**
9101 * cfg80211_calculate_bitrate - calculate actual bitrate (in 100Kbps units)
9102 * @rate: given rate_info to calculate bitrate from
9103 *
9104 * Return: calculated bitrate
9105 */
9106u32 cfg80211_calculate_bitrate(struct rate_info *rate);
9107
9108/**
9109 * cfg80211_unregister_wdev - remove the given wdev
9110 * @wdev: struct wireless_dev to remove
9111 *
9112 * This function removes the device so it can no longer be used. It is necessary
9113 * to call this function even when cfg80211 requests the removal of the device
9114 * by calling the del_virtual_intf() callback. The function must also be called
9115 * when the driver wishes to unregister the wdev, e.g. when the hardware device
9116 * is unbound from the driver.
9117 *
9118 * Context: Requires the RTNL and wiphy mutex to be held.
9119 */
9120void cfg80211_unregister_wdev(struct wireless_dev *wdev);
9121
9122/**
9123 * cfg80211_register_netdevice - register the given netdev
9124 * @dev: the netdev to register
9125 *
9126 * Note: In contexts coming from cfg80211 callbacks, you must call this rather
9127 * than register_netdevice(), unregister_netdev() is impossible as the RTNL is
9128 * held. Otherwise, both register_netdevice() and register_netdev() are usable
9129 * instead as well.
9130 *
9131 * Context: Requires the RTNL and wiphy mutex to be held.
9132 *
9133 * Return: 0 on success. Non-zero on error.
9134 */
9135int cfg80211_register_netdevice(struct net_device *dev);
9136
9137/**
9138 * cfg80211_unregister_netdevice - unregister the given netdev
9139 * @dev: the netdev to register
9140 *
9141 * Note: In contexts coming from cfg80211 callbacks, you must call this rather
9142 * than unregister_netdevice(), unregister_netdev() is impossible as the RTNL
9143 * is held. Otherwise, both unregister_netdevice() and unregister_netdev() are
9144 * usable instead as well.
9145 *
9146 * Context: Requires the RTNL and wiphy mutex to be held.
9147 */
9148static inline void cfg80211_unregister_netdevice(struct net_device *dev)
9149{
9150#if IS_ENABLED(CONFIG_CFG80211)
9151 cfg80211_unregister_wdev(dev->ieee80211_ptr);
9152#endif
9153}
9154
9155/**
9156 * struct cfg80211_ft_event_params - FT Information Elements
9157 * @ies: FT IEs
9158 * @ies_len: length of the FT IE in bytes
9159 * @target_ap: target AP's MAC address
9160 * @ric_ies: RIC IE
9161 * @ric_ies_len: length of the RIC IE in bytes
9162 */
9163struct cfg80211_ft_event_params {
9164 const u8 *ies;
9165 size_t ies_len;
9166 const u8 *target_ap;
9167 const u8 *ric_ies;
9168 size_t ric_ies_len;
9169};
9170
9171/**
9172 * cfg80211_ft_event - notify userspace about FT IE and RIC IE
9173 * @netdev: network device
9174 * @ft_event: IE information
9175 */
9176void cfg80211_ft_event(struct net_device *netdev,
9177 struct cfg80211_ft_event_params *ft_event);
9178
9179/**
9180 * cfg80211_get_p2p_attr - find and copy a P2P attribute from IE buffer
9181 * @ies: the input IE buffer
9182 * @len: the input length
9183 * @attr: the attribute ID to find
9184 * @buf: output buffer, can be %NULL if the data isn't needed, e.g.
9185 * if the function is only called to get the needed buffer size
9186 * @bufsize: size of the output buffer
9187 *
9188 * The function finds a given P2P attribute in the (vendor) IEs and
9189 * copies its contents to the given buffer.
9190 *
9191 * Return: A negative error code (-%EILSEQ or -%ENOENT) if the data is
9192 * malformed or the attribute can't be found (respectively), or the
9193 * length of the found attribute (which can be zero).
9194 */
9195int cfg80211_get_p2p_attr(const u8 *ies, unsigned int len,
9196 enum ieee80211_p2p_attr_id attr,
9197 u8 *buf, unsigned int bufsize);
9198
9199/**
9200 * ieee80211_ie_split_ric - split an IE buffer according to ordering (with RIC)
9201 * @ies: the IE buffer
9202 * @ielen: the length of the IE buffer
9203 * @ids: an array with element IDs that are allowed before
9204 * the split. A WLAN_EID_EXTENSION value means that the next
9205 * EID in the list is a sub-element of the EXTENSION IE.
9206 * @n_ids: the size of the element ID array
9207 * @after_ric: array IE types that come after the RIC element
9208 * @n_after_ric: size of the @after_ric array
9209 * @offset: offset where to start splitting in the buffer
9210 *
9211 * This function splits an IE buffer by updating the @offset
9212 * variable to point to the location where the buffer should be
9213 * split.
9214 *
9215 * It assumes that the given IE buffer is well-formed, this
9216 * has to be guaranteed by the caller!
9217 *
9218 * It also assumes that the IEs in the buffer are ordered
9219 * correctly, if not the result of using this function will not
9220 * be ordered correctly either, i.e. it does no reordering.
9221 *
9222 * Return: The offset where the next part of the buffer starts, which
9223 * may be @ielen if the entire (remainder) of the buffer should be
9224 * used.
9225 */
9226size_t ieee80211_ie_split_ric(const u8 *ies, size_t ielen,
9227 const u8 *ids, int n_ids,
9228 const u8 *after_ric, int n_after_ric,
9229 size_t offset);
9230
9231/**
9232 * ieee80211_ie_split - split an IE buffer according to ordering
9233 * @ies: the IE buffer
9234 * @ielen: the length of the IE buffer
9235 * @ids: an array with element IDs that are allowed before
9236 * the split. A WLAN_EID_EXTENSION value means that the next
9237 * EID in the list is a sub-element of the EXTENSION IE.
9238 * @n_ids: the size of the element ID array
9239 * @offset: offset where to start splitting in the buffer
9240 *
9241 * This function splits an IE buffer by updating the @offset
9242 * variable to point to the location where the buffer should be
9243 * split.
9244 *
9245 * It assumes that the given IE buffer is well-formed, this
9246 * has to be guaranteed by the caller!
9247 *
9248 * It also assumes that the IEs in the buffer are ordered
9249 * correctly, if not the result of using this function will not
9250 * be ordered correctly either, i.e. it does no reordering.
9251 *
9252 * Return: The offset where the next part of the buffer starts, which
9253 * may be @ielen if the entire (remainder) of the buffer should be
9254 * used.
9255 */
9256static inline size_t ieee80211_ie_split(const u8 *ies, size_t ielen,
9257 const u8 *ids, int n_ids, size_t offset)
9258{
9259 return ieee80211_ie_split_ric(ies, ielen, ids, n_ids, NULL, 0, offset);
9260}
9261
9262/**
9263 * ieee80211_fragment_element - fragment the last element in skb
9264 * @skb: The skbuf that the element was added to
9265 * @len_pos: Pointer to length of the element to fragment
9266 * @frag_id: The element ID to use for fragments
9267 *
9268 * This function fragments all data after @len_pos, adding fragmentation
9269 * elements with the given ID as appropriate. The SKB will grow in size
9270 * accordingly.
9271 */
9272void ieee80211_fragment_element(struct sk_buff *skb, u8 *len_pos, u8 frag_id);
9273
9274/**
9275 * cfg80211_report_wowlan_wakeup - report wakeup from WoWLAN
9276 * @wdev: the wireless device reporting the wakeup
9277 * @wakeup: the wakeup report
9278 * @gfp: allocation flags
9279 *
9280 * This function reports that the given device woke up. If it
9281 * caused the wakeup, report the reason(s), otherwise you may
9282 * pass %NULL as the @wakeup parameter to advertise that something
9283 * else caused the wakeup.
9284 */
9285void cfg80211_report_wowlan_wakeup(struct wireless_dev *wdev,
9286 struct cfg80211_wowlan_wakeup *wakeup,
9287 gfp_t gfp);
9288
9289/**
9290 * cfg80211_crit_proto_stopped() - indicate critical protocol stopped by driver.
9291 *
9292 * @wdev: the wireless device for which critical protocol is stopped.
9293 * @gfp: allocation flags
9294 *
9295 * This function can be called by the driver to indicate it has reverted
9296 * operation back to normal. One reason could be that the duration given
9297 * by .crit_proto_start() has expired.
9298 */
9299void cfg80211_crit_proto_stopped(struct wireless_dev *wdev, gfp_t gfp);
9300
9301/**
9302 * ieee80211_get_num_supported_channels - get number of channels device has
9303 * @wiphy: the wiphy
9304 *
9305 * Return: the number of channels supported by the device.
9306 */
9307unsigned int ieee80211_get_num_supported_channels(struct wiphy *wiphy);
9308
9309/**
9310 * cfg80211_check_combinations - check interface combinations
9311 *
9312 * @wiphy: the wiphy
9313 * @params: the interface combinations parameter
9314 *
9315 * This function can be called by the driver to check whether a
9316 * combination of interfaces and their types are allowed according to
9317 * the interface combinations.
9318 *
9319 * Return: 0 if combinations are allowed. Non-zero on error.
9320 */
9321int cfg80211_check_combinations(struct wiphy *wiphy,
9322 struct iface_combination_params *params);
9323
9324/**
9325 * cfg80211_iter_combinations - iterate over matching combinations
9326 *
9327 * @wiphy: the wiphy
9328 * @params: the interface combinations parameter
9329 * @iter: function to call for each matching combination
9330 * @data: pointer to pass to iter function
9331 *
9332 * This function can be called by the driver to check what possible
9333 * combinations it fits in at a given moment, e.g. for channel switching
9334 * purposes.
9335 *
9336 * Return: 0 on success. Non-zero on error.
9337 */
9338int cfg80211_iter_combinations(struct wiphy *wiphy,
9339 struct iface_combination_params *params,
9340 void (*iter)(const struct ieee80211_iface_combination *c,
9341 void *data),
9342 void *data);
9343
9344/**
9345 * cfg80211_stop_iface - trigger interface disconnection
9346 *
9347 * @wiphy: the wiphy
9348 * @wdev: wireless device
9349 * @gfp: context flags
9350 *
9351 * Trigger interface to be stopped as if AP was stopped, IBSS/mesh left, STA
9352 * disconnected.
9353 *
9354 * Note: This doesn't need any locks and is asynchronous.
9355 */
9356void cfg80211_stop_iface(struct wiphy *wiphy, struct wireless_dev *wdev,
9357 gfp_t gfp);
9358
9359/**
9360 * cfg80211_shutdown_all_interfaces - shut down all interfaces for a wiphy
9361 * @wiphy: the wiphy to shut down
9362 *
9363 * This function shuts down all interfaces belonging to this wiphy by
9364 * calling dev_close() (and treating non-netdev interfaces as needed).
9365 * It shouldn't really be used unless there are some fatal device errors
9366 * that really can't be recovered in any other way.
9367 *
9368 * Callers must hold the RTNL and be able to deal with callbacks into
9369 * the driver while the function is running.
9370 */
9371void cfg80211_shutdown_all_interfaces(struct wiphy *wiphy);
9372
9373/**
9374 * wiphy_ext_feature_set - set the extended feature flag
9375 *
9376 * @wiphy: the wiphy to modify.
9377 * @ftidx: extended feature bit index.
9378 *
9379 * The extended features are flagged in multiple bytes (see
9380 * &struct wiphy.@ext_features)
9381 */
9382static inline void wiphy_ext_feature_set(struct wiphy *wiphy,
9383 enum nl80211_ext_feature_index ftidx)
9384{
9385 u8 *ft_byte;
9386
9387 ft_byte = &wiphy->ext_features[ftidx / 8];
9388 *ft_byte |= BIT(ftidx % 8);
9389}
9390
9391/**
9392 * wiphy_ext_feature_isset - check the extended feature flag
9393 *
9394 * @wiphy: the wiphy to modify.
9395 * @ftidx: extended feature bit index.
9396 *
9397 * The extended features are flagged in multiple bytes (see
9398 * &struct wiphy.@ext_features)
9399 *
9400 * Return: %true if extended feature flag is set, %false otherwise
9401 */
9402static inline bool
9403wiphy_ext_feature_isset(struct wiphy *wiphy,
9404 enum nl80211_ext_feature_index ftidx)
9405{
9406 u8 ft_byte;
9407
9408 ft_byte = wiphy->ext_features[ftidx / 8];
9409 return (ft_byte & BIT(ftidx % 8)) != 0;
9410}
9411
9412/**
9413 * cfg80211_free_nan_func - free NAN function
9414 * @f: NAN function that should be freed
9415 *
9416 * Frees all the NAN function and all it's allocated members.
9417 */
9418void cfg80211_free_nan_func(struct cfg80211_nan_func *f);
9419
9420/**
9421 * struct cfg80211_nan_match_params - NAN match parameters
9422 * @type: the type of the function that triggered a match. If it is
9423 * %NL80211_NAN_FUNC_SUBSCRIBE it means that we replied to a subscriber.
9424 * If it is %NL80211_NAN_FUNC_PUBLISH, it means that we got a discovery
9425 * result.
9426 * If it is %NL80211_NAN_FUNC_FOLLOW_UP, we received a follow up.
9427 * @inst_id: the local instance id
9428 * @peer_inst_id: the instance id of the peer's function
9429 * @addr: the MAC address of the peer
9430 * @info_len: the length of the &info
9431 * @info: the Service Specific Info from the peer (if any)
9432 * @cookie: unique identifier of the corresponding function
9433 */
9434struct cfg80211_nan_match_params {
9435 enum nl80211_nan_function_type type;
9436 u8 inst_id;
9437 u8 peer_inst_id;
9438 const u8 *addr;
9439 u8 info_len;
9440 const u8 *info;
9441 u64 cookie;
9442};
9443
9444/**
9445 * cfg80211_nan_match - report a match for a NAN function.
9446 * @wdev: the wireless device reporting the match
9447 * @match: match notification parameters
9448 * @gfp: allocation flags
9449 *
9450 * This function reports that the a NAN function had a match. This
9451 * can be a subscribe that had a match or a solicited publish that
9452 * was sent. It can also be a follow up that was received.
9453 */
9454void cfg80211_nan_match(struct wireless_dev *wdev,
9455 struct cfg80211_nan_match_params *match, gfp_t gfp);
9456
9457/**
9458 * cfg80211_nan_func_terminated - notify about NAN function termination.
9459 *
9460 * @wdev: the wireless device reporting the match
9461 * @inst_id: the local instance id
9462 * @reason: termination reason (one of the NL80211_NAN_FUNC_TERM_REASON_*)
9463 * @cookie: unique NAN function identifier
9464 * @gfp: allocation flags
9465 *
9466 * This function reports that the a NAN function is terminated.
9467 */
9468void cfg80211_nan_func_terminated(struct wireless_dev *wdev,
9469 u8 inst_id,
9470 enum nl80211_nan_func_term_reason reason,
9471 u64 cookie, gfp_t gfp);
9472
9473/* ethtool helper */
9474void cfg80211_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info);
9475
9476/**
9477 * cfg80211_external_auth_request - userspace request for authentication
9478 * @netdev: network device
9479 * @params: External authentication parameters
9480 * @gfp: allocation flags
9481 * Returns: 0 on success, < 0 on error
9482 */
9483int cfg80211_external_auth_request(struct net_device *netdev,
9484 struct cfg80211_external_auth_params *params,
9485 gfp_t gfp);
9486
9487/**
9488 * cfg80211_pmsr_report - report peer measurement result data
9489 * @wdev: the wireless device reporting the measurement
9490 * @req: the original measurement request
9491 * @result: the result data
9492 * @gfp: allocation flags
9493 */
9494void cfg80211_pmsr_report(struct wireless_dev *wdev,
9495 struct cfg80211_pmsr_request *req,
9496 struct cfg80211_pmsr_result *result,
9497 gfp_t gfp);
9498
9499/**
9500 * cfg80211_pmsr_complete - report peer measurement completed
9501 * @wdev: the wireless device reporting the measurement
9502 * @req: the original measurement request
9503 * @gfp: allocation flags
9504 *
9505 * Report that the entire measurement completed, after this
9506 * the request pointer will no longer be valid.
9507 */
9508void cfg80211_pmsr_complete(struct wireless_dev *wdev,
9509 struct cfg80211_pmsr_request *req,
9510 gfp_t gfp);
9511
9512/**
9513 * cfg80211_iftype_allowed - check whether the interface can be allowed
9514 * @wiphy: the wiphy
9515 * @iftype: interface type
9516 * @is_4addr: use_4addr flag, must be '0' when check_swif is '1'
9517 * @check_swif: check iftype against software interfaces
9518 *
9519 * Check whether the interface is allowed to operate; additionally, this API
9520 * can be used to check iftype against the software interfaces when
9521 * check_swif is '1'.
9522 *
9523 * Return: %true if allowed, %false otherwise
9524 */
9525bool cfg80211_iftype_allowed(struct wiphy *wiphy, enum nl80211_iftype iftype,
9526 bool is_4addr, u8 check_swif);
9527
9528
9529/**
9530 * cfg80211_assoc_comeback - notification of association that was
9531 * temporarily rejected with a comeback
9532 * @netdev: network device
9533 * @ap_addr: AP (MLD) address that rejected the association
9534 * @timeout: timeout interval value TUs.
9535 *
9536 * this function may sleep. the caller must hold the corresponding wdev's mutex.
9537 */
9538void cfg80211_assoc_comeback(struct net_device *netdev,
9539 const u8 *ap_addr, u32 timeout);
9540
9541/* Logging, debugging and troubleshooting/diagnostic helpers. */
9542
9543/* wiphy_printk helpers, similar to dev_printk */
9544
9545#define wiphy_printk(level, wiphy, format, args...) \
9546 dev_printk(level, &(wiphy)->dev, format, ##args)
9547#define wiphy_emerg(wiphy, format, args...) \
9548 dev_emerg(&(wiphy)->dev, format, ##args)
9549#define wiphy_alert(wiphy, format, args...) \
9550 dev_alert(&(wiphy)->dev, format, ##args)
9551#define wiphy_crit(wiphy, format, args...) \
9552 dev_crit(&(wiphy)->dev, format, ##args)
9553#define wiphy_err(wiphy, format, args...) \
9554 dev_err(&(wiphy)->dev, format, ##args)
9555#define wiphy_warn(wiphy, format, args...) \
9556 dev_warn(&(wiphy)->dev, format, ##args)
9557#define wiphy_notice(wiphy, format, args...) \
9558 dev_notice(&(wiphy)->dev, format, ##args)
9559#define wiphy_info(wiphy, format, args...) \
9560 dev_info(&(wiphy)->dev, format, ##args)
9561#define wiphy_info_once(wiphy, format, args...) \
9562 dev_info_once(&(wiphy)->dev, format, ##args)
9563
9564#define wiphy_err_ratelimited(wiphy, format, args...) \
9565 dev_err_ratelimited(&(wiphy)->dev, format, ##args)
9566#define wiphy_warn_ratelimited(wiphy, format, args...) \
9567 dev_warn_ratelimited(&(wiphy)->dev, format, ##args)
9568
9569#define wiphy_debug(wiphy, format, args...) \
9570 wiphy_printk(KERN_DEBUG, wiphy, format, ##args)
9571
9572#define wiphy_dbg(wiphy, format, args...) \
9573 dev_dbg(&(wiphy)->dev, format, ##args)
9574
9575#if defined(VERBOSE_DEBUG)
9576#define wiphy_vdbg wiphy_dbg
9577#else
9578#define wiphy_vdbg(wiphy, format, args...) \
9579({ \
9580 if (0) \
9581 wiphy_printk(KERN_DEBUG, wiphy, format, ##args); \
9582 0; \
9583})
9584#endif
9585
9586/*
9587 * wiphy_WARN() acts like wiphy_printk(), but with the key difference
9588 * of using a WARN/WARN_ON to get the message out, including the
9589 * file/line information and a backtrace.
9590 */
9591#define wiphy_WARN(wiphy, format, args...) \
9592 WARN(1, "wiphy: %s\n" format, wiphy_name(wiphy), ##args);
9593
9594/**
9595 * cfg80211_update_owe_info_event - Notify the peer's OWE info to user space
9596 * @netdev: network device
9597 * @owe_info: peer's owe info
9598 * @gfp: allocation flags
9599 */
9600void cfg80211_update_owe_info_event(struct net_device *netdev,
9601 struct cfg80211_update_owe_info *owe_info,
9602 gfp_t gfp);
9603
9604/**
9605 * cfg80211_bss_flush - resets all the scan entries
9606 * @wiphy: the wiphy
9607 */
9608void cfg80211_bss_flush(struct wiphy *wiphy);
9609
9610/**
9611 * cfg80211_bss_color_notify - notify about bss color event
9612 * @dev: network device
9613 * @cmd: the actual event we want to notify
9614 * @count: the number of TBTTs until the color change happens
9615 * @color_bitmap: representations of the colors that the local BSS is aware of
9616 * @link_id: valid link_id in case of MLO or 0 for non-MLO.
9617 *
9618 * Return: 0 on success. Non-zero on error.
9619 */
9620int cfg80211_bss_color_notify(struct net_device *dev,
9621 enum nl80211_commands cmd, u8 count,
9622 u64 color_bitmap, u8 link_id);
9623
9624/**
9625 * cfg80211_obss_color_collision_notify - notify about bss color collision
9626 * @dev: network device
9627 * @color_bitmap: representations of the colors that the local BSS is aware of
9628 * @link_id: valid link_id in case of MLO or 0 for non-MLO.
9629 *
9630 * Return: 0 on success. Non-zero on error.
9631 */
9632static inline int cfg80211_obss_color_collision_notify(struct net_device *dev,
9633 u64 color_bitmap,
9634 u8 link_id)
9635{
9636 return cfg80211_bss_color_notify(dev, NL80211_CMD_OBSS_COLOR_COLLISION,
9637 0, color_bitmap, link_id);
9638}
9639
9640/**
9641 * cfg80211_color_change_started_notify - notify color change start
9642 * @dev: the device on which the color is switched
9643 * @count: the number of TBTTs until the color change happens
9644 * @link_id: valid link_id in case of MLO or 0 for non-MLO.
9645 *
9646 * Inform the userspace about the color change that has started.
9647 *
9648 * Return: 0 on success. Non-zero on error.
9649 */
9650static inline int cfg80211_color_change_started_notify(struct net_device *dev,
9651 u8 count, u8 link_id)
9652{
9653 return cfg80211_bss_color_notify(dev, NL80211_CMD_COLOR_CHANGE_STARTED,
9654 count, 0, link_id);
9655}
9656
9657/**
9658 * cfg80211_color_change_aborted_notify - notify color change abort
9659 * @dev: the device on which the color is switched
9660 * @link_id: valid link_id in case of MLO or 0 for non-MLO.
9661 *
9662 * Inform the userspace about the color change that has aborted.
9663 *
9664 * Return: 0 on success. Non-zero on error.
9665 */
9666static inline int cfg80211_color_change_aborted_notify(struct net_device *dev,
9667 u8 link_id)
9668{
9669 return cfg80211_bss_color_notify(dev, NL80211_CMD_COLOR_CHANGE_ABORTED,
9670 0, 0, link_id);
9671}
9672
9673/**
9674 * cfg80211_color_change_notify - notify color change completion
9675 * @dev: the device on which the color was switched
9676 * @link_id: valid link_id in case of MLO or 0 for non-MLO.
9677 *
9678 * Inform the userspace about the color change that has completed.
9679 *
9680 * Return: 0 on success. Non-zero on error.
9681 */
9682static inline int cfg80211_color_change_notify(struct net_device *dev,
9683 u8 link_id)
9684{
9685 return cfg80211_bss_color_notify(dev,
9686 NL80211_CMD_COLOR_CHANGE_COMPLETED,
9687 0, 0, link_id);
9688}
9689
9690/**
9691 * cfg80211_links_removed - Notify about removed STA MLD setup links.
9692 * @dev: network device.
9693 * @link_mask: BIT mask of removed STA MLD setup link IDs.
9694 *
9695 * Inform cfg80211 and the userspace about removed STA MLD setup links due to
9696 * AP MLD removing the corresponding affiliated APs with Multi-Link
9697 * reconfiguration. Note that it's not valid to remove all links, in this
9698 * case disconnect instead.
9699 * Also note that the wdev mutex must be held.
9700 */
9701void cfg80211_links_removed(struct net_device *dev, u16 link_mask);
9702
9703/**
9704 * cfg80211_schedule_channels_check - schedule regulatory check if needed
9705 * @wdev: the wireless device to check
9706 *
9707 * In case the device supports NO_IR or DFS relaxations, schedule regulatory
9708 * channels check, as previous concurrent operation conditions may not
9709 * hold anymore.
9710 */
9711void cfg80211_schedule_channels_check(struct wireless_dev *wdev);
9712
9713#ifdef CONFIG_CFG80211_DEBUGFS
9714/**
9715 * wiphy_locked_debugfs_read - do a locked read in debugfs
9716 * @wiphy: the wiphy to use
9717 * @file: the file being read
9718 * @buf: the buffer to fill and then read from
9719 * @bufsize: size of the buffer
9720 * @userbuf: the user buffer to copy to
9721 * @count: read count
9722 * @ppos: read position
9723 * @handler: the read handler to call (under wiphy lock)
9724 * @data: additional data to pass to the read handler
9725 *
9726 * Return: the number of characters read, or a negative errno
9727 */
9728ssize_t wiphy_locked_debugfs_read(struct wiphy *wiphy, struct file *file,
9729 char *buf, size_t bufsize,
9730 char __user *userbuf, size_t count,
9731 loff_t *ppos,
9732 ssize_t (*handler)(struct wiphy *wiphy,
9733 struct file *file,
9734 char *buf,
9735 size_t bufsize,
9736 void *data),
9737 void *data);
9738
9739/**
9740 * wiphy_locked_debugfs_write - do a locked write in debugfs
9741 * @wiphy: the wiphy to use
9742 * @file: the file being written to
9743 * @buf: the buffer to copy the user data to
9744 * @bufsize: size of the buffer
9745 * @userbuf: the user buffer to copy from
9746 * @count: read count
9747 * @handler: the write handler to call (under wiphy lock)
9748 * @data: additional data to pass to the write handler
9749 *
9750 * Return: the number of characters written, or a negative errno
9751 */
9752ssize_t wiphy_locked_debugfs_write(struct wiphy *wiphy, struct file *file,
9753 char *buf, size_t bufsize,
9754 const char __user *userbuf, size_t count,
9755 ssize_t (*handler)(struct wiphy *wiphy,
9756 struct file *file,
9757 char *buf,
9758 size_t count,
9759 void *data),
9760 void *data);
9761#endif
9762
9763#endif /* __NET_CFG80211_H */