Linux Audio

Check our new training course

Loading...
v5.14.15
  1// SPDX-License-Identifier: GPL-2.0
  2/*
  3 * Device Tree Source for the Gose board
  4 *
  5 * Copyright (C) 2014-2015 Renesas Electronics Corporation
 
 
 
 
  6 */
  7
  8/*
  9 * SSI-AK4643
 10 *
 11 * SW1: 1: AK4643
 12 *      2: CN22
 13 *      3: ADV7511
 14 *
 15 * This command is required when Playback/Capture
 16 *
 17 *	amixer set "LINEOUT Mixer DACL" on
 18 *	amixer set "DVC Out" 100%
 19 *	amixer set "DVC In" 100%
 20 *
 21 * You can use Mute
 22 *
 23 *	amixer set "DVC Out Mute" on
 24 *	amixer set "DVC In Mute" on
 25 *
 26 * You can use Volume Ramp
 27 *
 28 *	amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
 29 *	amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
 30 *	amixer set "DVC Out Ramp" on
 31 *	aplay xxx.wav &
 32 *	amixer set "DVC Out"  80%  // Volume Down
 33 *	amixer set "DVC Out" 100%  // Volume Up
 34 */
 35
 36/dts-v1/;
 37#include "r8a7793.dtsi"
 38#include <dt-bindings/gpio/gpio.h>
 39#include <dt-bindings/input/input.h>
 40
 41/ {
 42	model = "Gose";
 43	compatible = "renesas,gose", "renesas,r8a7793";
 44
 45	aliases {
 46		serial0 = &scif0;
 47		serial1 = &scif1;
 48		i2c9 = &gpioi2c2;
 49		i2c10 = &gpioi2c4;
 50		i2c11 = &i2chdmi;
 51		i2c12 = &i2cexio4;
 52		mmc0 = &sdhi0;
 53		mmc1 = &sdhi1;
 54		mmc2 = &sdhi2;
 55	};
 56
 57	chosen {
 58		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
 59		stdout-path = "serial0:115200n8";
 60	};
 61
 62	memory@40000000 {
 63		device_type = "memory";
 64		reg = <0 0x40000000 0 0x40000000>;
 65	};
 66
 67	keyboard {
 68		compatible = "gpio-keys";
 69
 70		pinctrl-0 = <&keyboard_pins>;
 71		pinctrl-names = "default";
 72
 73		key-1 {
 74			gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
 75			linux,code = <KEY_1>;
 76			label = "SW2-1";
 77			wakeup-source;
 78			debounce-interval = <20>;
 79		};
 80		key-2 {
 81			gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
 82			linux,code = <KEY_2>;
 83			label = "SW2-2";
 84			wakeup-source;
 85			debounce-interval = <20>;
 86		};
 87		key-3 {
 88			gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
 89			linux,code = <KEY_3>;
 90			label = "SW2-3";
 91			wakeup-source;
 92			debounce-interval = <20>;
 93		};
 94		key-4 {
 95			gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
 96			linux,code = <KEY_4>;
 97			label = "SW2-4";
 98			wakeup-source;
 99			debounce-interval = <20>;
100		};
101		key-a {
102			gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
103			linux,code = <KEY_A>;
104			label = "SW30";
105			wakeup-source;
106			debounce-interval = <20>;
107		};
108		key-b {
109			gpios = <&gpio7 1 GPIO_ACTIVE_LOW>;
110			linux,code = <KEY_B>;
111			label = "SW31";
112			wakeup-source;
113			debounce-interval = <20>;
114		};
115		key-c {
116			gpios = <&gpio7 2 GPIO_ACTIVE_LOW>;
117			linux,code = <KEY_C>;
118			label = "SW32";
119			wakeup-source;
120			debounce-interval = <20>;
121		};
122		key-d {
123			gpios = <&gpio7 3 GPIO_ACTIVE_LOW>;
124			linux,code = <KEY_D>;
125			label = "SW33";
126			wakeup-source;
127			debounce-interval = <20>;
128		};
129		key-e {
130			gpios = <&gpio7 4 GPIO_ACTIVE_LOW>;
131			linux,code = <KEY_E>;
132			label = "SW34";
133			wakeup-source;
134			debounce-interval = <20>;
135		};
136		key-f {
137			gpios = <&gpio7 5 GPIO_ACTIVE_LOW>;
138			linux,code = <KEY_F>;
139			label = "SW35";
140			wakeup-source;
141			debounce-interval = <20>;
142		};
143		key-g {
144			gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
145			linux,code = <KEY_G>;
146			label = "SW36";
147			wakeup-source;
148			debounce-interval = <20>;
149		};
150	};
151
152	leds {
153		compatible = "gpio-leds";
154		led6 {
155			gpios = <&gpio2 19 GPIO_ACTIVE_HIGH>;
156			label = "LED6";
157		};
158		led7 {
159			gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
160			label = "LED7";
161		};
162		led8 {
163			gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>;
164			label = "LED8";
165		};
166	};
167
168	vcc_sdhi0: regulator-vcc-sdhi0 {
169		compatible = "regulator-fixed";
170
171		regulator-name = "SDHI0 Vcc";
172		regulator-min-microvolt = <3300000>;
173		regulator-max-microvolt = <3300000>;
174
175		gpio = <&gpio7 17 GPIO_ACTIVE_HIGH>;
176		enable-active-high;
177	};
178
179	vccq_sdhi0: regulator-vccq-sdhi0 {
180		compatible = "regulator-gpio";
181
182		regulator-name = "SDHI0 VccQ";
183		regulator-min-microvolt = <1800000>;
184		regulator-max-microvolt = <3300000>;
185
186		gpios = <&gpio2 12 GPIO_ACTIVE_HIGH>;
187		gpios-states = <1>;
188		states = <3300000 1>, <1800000 0>;
189	};
190
191	vcc_sdhi1: regulator-vcc-sdhi1 {
192		compatible = "regulator-fixed";
193
194		regulator-name = "SDHI1 Vcc";
195		regulator-min-microvolt = <3300000>;
196		regulator-max-microvolt = <3300000>;
197
198		gpio = <&gpio7 18 GPIO_ACTIVE_HIGH>;
199		enable-active-high;
200	};
201
202	vccq_sdhi1: regulator-vccq-sdhi1 {
203		compatible = "regulator-gpio";
204
205		regulator-name = "SDHI1 VccQ";
206		regulator-min-microvolt = <1800000>;
207		regulator-max-microvolt = <3300000>;
208
209		gpios = <&gpio2 13 GPIO_ACTIVE_HIGH>;
210		gpios-states = <1>;
211		states = <3300000 1>, <1800000 0>;
212	};
213
214	vcc_sdhi2: regulator-vcc-sdhi2 {
215		compatible = "regulator-fixed";
216
217		regulator-name = "SDHI2 Vcc";
218		regulator-min-microvolt = <3300000>;
219		regulator-max-microvolt = <3300000>;
220
221		gpio = <&gpio7 19 GPIO_ACTIVE_HIGH>;
222		enable-active-high;
223	};
224
225	vccq_sdhi2: regulator-vccq-sdhi2 {
226		compatible = "regulator-gpio";
227
228		regulator-name = "SDHI2 VccQ";
229		regulator-min-microvolt = <1800000>;
230		regulator-max-microvolt = <3300000>;
231
232		gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
233		gpios-states = <1>;
234		states = <3300000 1>, <1800000 0>;
235	};
236
237	audio_clock: audio_clock {
238		compatible = "fixed-clock";
239		#clock-cells = <0>;
240		clock-frequency = <11289600>;
 
241	};
242
243	rsnd_ak4643: sound {
244		compatible = "simple-audio-card";
245
246		simple-audio-card,format = "left_j";
247		simple-audio-card,bitclock-master = <&sndcodec>;
248		simple-audio-card,frame-master = <&sndcodec>;
249
250		sndcpu: simple-audio-card,cpu {
251			sound-dai = <&rcar_sound>;
252		};
253
254		sndcodec: simple-audio-card,codec {
255			sound-dai = <&ak4643>;
256			clocks = <&audio_clock>;
257		};
258	};
259
260	hdmi-in {
261		compatible = "hdmi-connector";
262		type = "a";
263
264		port {
265			hdmi_con_in: endpoint {
266				remote-endpoint = <&adv7612_in>;
267			};
268		};
269	};
270
271	hdmi-out {
272		compatible = "hdmi-connector";
273		type = "a";
274
275		port {
276			hdmi_con_out: endpoint {
277				remote-endpoint = <&adv7511_out>;
278			};
279		};
280	};
281
282	composite-in {
283		compatible = "composite-video-connector";
284
285		port {
286			composite_con_in: endpoint {
287				remote-endpoint = <&adv7180_in>;
288			};
289		};
290	};
291
292	x2_clk: x2-clock {
293		compatible = "fixed-clock";
294		#clock-cells = <0>;
295		clock-frequency = <74250000>;
296	};
297
298	x13_clk: x13-clock {
299		compatible = "fixed-clock";
300		#clock-cells = <0>;
301		clock-frequency = <148500000>;
302	};
303
304	gpioi2c2: i2c-9 {
305		#address-cells = <1>;
306		#size-cells = <0>;
307		compatible = "i2c-gpio";
308		status = "disabled";
309		scl-gpios = <&gpio2 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
310		sda-gpios = <&gpio2 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
311		i2c-gpio,delay-us = <5>;
312	};
313
314	gpioi2c4: i2c-10 {
315		#address-cells = <1>;
316		#size-cells = <0>;
317		compatible = "i2c-gpio";
318		status = "disabled";
319		scl-gpios = <&gpio7 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
320		sda-gpios = <&gpio7 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
321		i2c-gpio,delay-us = <5>;
322	};
323
324	/*
325	 * A fallback to GPIO is provided for I2C2.
326	 */
327	i2chdmi: i2c-11 {
328		compatible = "i2c-demux-pinctrl";
329		i2c-parent = <&i2c2>, <&gpioi2c2>;
330		i2c-bus-name = "i2c-hdmi";
331		#address-cells = <1>;
332		#size-cells = <0>;
333
334		ak4643: codec@12 {
335			compatible = "asahi-kasei,ak4643";
336			#sound-dai-cells = <0>;
337			reg = <0x12>;
338		};
339
340		composite-in@20 {
341			compatible = "adi,adv7180cp";
342			reg = <0x20>;
343
344			ports {
345				#address-cells = <1>;
346				#size-cells = <0>;
347
348				port@0 {
349					reg = <0>;
350					adv7180_in: endpoint {
351						remote-endpoint = <&composite_con_in>;
352					};
353				};
354
355				port@3 {
356					reg = <3>;
357					adv7180_out: endpoint {
358						bus-width = <8>;
359						remote-endpoint = <&vin1ep>;
360					};
361				};
362			};
363		};
364
365		hdmi@39 {
366			compatible = "adi,adv7511w";
367			reg = <0x39>;
368			interrupt-parent = <&gpio3>;
369			interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
370
371			adi,input-depth = <8>;
372			adi,input-colorspace = "rgb";
373			adi,input-clock = "1x";
374
375			ports {
376				#address-cells = <1>;
377				#size-cells = <0>;
378
379				port@0 {
380					reg = <0>;
381					adv7511_in: endpoint {
382						remote-endpoint = <&du_out_rgb>;
383					};
384				};
385
386				port@1 {
387					reg = <1>;
388					adv7511_out: endpoint {
389						remote-endpoint = <&hdmi_con_out>;
390					};
391				};
392			};
393		};
394
395		hdmi-in@4c {
396			compatible = "adi,adv7612";
397			reg = <0x4c>;
398			interrupt-parent = <&gpio4>;
399			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
400			default-input = <0>;
401
402			ports {
403				#address-cells = <1>;
404				#size-cells = <0>;
405
406				port@0 {
407					reg = <0>;
408					adv7612_in: endpoint {
409						remote-endpoint = <&hdmi_con_in>;
410					};
411				};
412
413				port@2 {
414					reg = <2>;
415					adv7612_out: endpoint {
416						remote-endpoint = <&vin0ep2>;
417					};
418				};
419			};
420		};
421
422		eeprom@50 {
423			compatible = "renesas,r1ex24002", "atmel,24c02";
424			reg = <0x50>;
425			pagesize = <16>;
426		};
427	};
428
429	/*
430	 * I2C4 is routed to EXIO connector E, pins 37 (SCL) + 39 (SDA).
431	 * A fallback to GPIO is provided.
432	 */
433	i2cexio4: i2c-12 {
434		compatible = "i2c-demux-pinctrl";
435		i2c-parent = <&i2c4>, <&gpioi2c4>;
436		i2c-bus-name = "i2c-exio4";
437		#address-cells = <1>;
438		#size-cells = <0>;
439	};
440};
441
442&du {
443	pinctrl-0 = <&du_pins>;
444	pinctrl-names = "default";
445	status = "okay";
446
447	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>,
 
 
448		 <&x13_clk>, <&x2_clk>;
449	clock-names = "du.0", "du.1", "dclkin.0", "dclkin.1";
 
450
451	ports {
452		port@0 {
453			endpoint {
454				remote-endpoint = <&adv7511_in>;
455			};
456		};
457	};
458};
459
460&lvds0 {
461	ports {
462		port@1 {
463			lvds_connector: endpoint {
464			};
465		};
466	};
467};
468
469&extal_clk {
470	clock-frequency = <20000000>;
471};
472
473&pfc {
474	pinctrl-0 = <&scif_clk_pins>;
475	pinctrl-names = "default";
476
477	i2c2_pins: i2c2 {
478		groups = "i2c2";
479		function = "i2c2";
480	};
481
482	i2c4_pins: i2c4 {
483		groups = "i2c4_c";
484		function = "i2c4";
485	};
486
487	du_pins: du {
488		groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
489		function = "du";
490	};
491
492	scif0_pins: scif0 {
493		groups = "scif0_data_d";
494		function = "scif0";
495	};
496
497	scif1_pins: scif1 {
498		groups = "scif1_data_d";
499		function = "scif1";
500	};
501
502	scif_clk_pins: scif_clk {
503		groups = "scif_clk";
504		function = "scif_clk";
505	};
506
507	ether_pins: ether {
508		groups = "eth_link", "eth_mdio", "eth_rmii";
509		function = "eth";
510	};
511
512	phy1_pins: phy1 {
513		groups = "intc_irq0";
514		function = "intc";
515	};
516
517	pmic_irq_pins: pmicirq {
518		groups = "intc_irq2";
519		function = "intc";
520	};
521
522	sdhi0_pins: sd0 {
523		groups = "sdhi0_data4", "sdhi0_ctrl";
524		function = "sdhi0";
525		power-source = <3300>;
526	};
527
528	sdhi0_pins_uhs: sd0_uhs {
529		groups = "sdhi0_data4", "sdhi0_ctrl";
530		function = "sdhi0";
531		power-source = <1800>;
532	};
533
534	sdhi1_pins: sd1 {
535		groups = "sdhi1_data4", "sdhi1_ctrl";
536		function = "sdhi1";
537		power-source = <3300>;
538	};
539
540	sdhi1_pins_uhs: sd1_uhs {
541		groups = "sdhi1_data4", "sdhi1_ctrl";
542		function = "sdhi1";
543		power-source = <1800>;
544	};
545
546	sdhi2_pins: sd2 {
547		groups = "sdhi2_data4", "sdhi2_ctrl";
548		function = "sdhi2";
549		power-source = <3300>;
550	};
551
552	sdhi2_pins_uhs: sd2_uhs {
553		groups = "sdhi2_data4", "sdhi2_ctrl";
554		function = "sdhi2";
555		power-source = <1800>;
556	};
557
558	qspi_pins: qspi {
559		groups = "qspi_ctrl", "qspi_data4";
560		function = "qspi";
561	};
562
563	sound_pins: sound {
564		groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data";
565		function = "ssi";
566	};
567
568	sound_clk_pins: sound_clk {
569		groups = "audio_clk_a";
570		function = "audio_clk";
571	};
572
573	keyboard_pins: keyboard {
574		pins = "GP_5_0", "GP_5_1", "GP_5_2", "GP_5_3";
575		bias-pull-up;
576	};
577
578	vin0_pins: vin0 {
579		groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk";
580		function = "vin0";
581	};
582
583	vin1_pins: vin1 {
584		groups = "vin1_data8", "vin1_clk";
585		function = "vin1";
586	};
587};
588
589&ether {
590	pinctrl-0 = <&ether_pins>, <&phy1_pins>;
591	pinctrl-names = "default";
592
593	phy-handle = <&phy1>;
594	renesas,ether-link-active-low;
595	status = "okay";
596
597	phy1: ethernet-phy@1 {
598		reg = <1>;
599		interrupt-parent = <&irqc0>;
600		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
601		micrel,led-mode = <1>;
602		reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
603	};
604};
605
606&cmt0 {
607	status = "okay";
608};
609
610&cpu0 {
611	cpu0-supply = <&vdd_dvfs>;
612};
613
614&rwdt {
615	timeout-sec = <60>;
616	status = "okay";
617};
618
619&scif0 {
620	pinctrl-0 = <&scif0_pins>;
621	pinctrl-names = "default";
622
623	status = "okay";
624};
625
626&scif1 {
627	pinctrl-0 = <&scif1_pins>;
628	pinctrl-names = "default";
629
630	status = "okay";
631};
632
633&scif_clk {
634	clock-frequency = <14745600>;
635};
636
637&sdhi0 {
638	pinctrl-0 = <&sdhi0_pins>;
639	pinctrl-1 = <&sdhi0_pins_uhs>;
640	pinctrl-names = "default", "state_uhs";
641
642	vmmc-supply = <&vcc_sdhi0>;
643	vqmmc-supply = <&vccq_sdhi0>;
644	cd-gpios = <&gpio6 6 GPIO_ACTIVE_LOW>;
645	wp-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
646	sd-uhs-sdr50;
647	sd-uhs-sdr104;
648	status = "okay";
649};
650
651&sdhi1 {
652	pinctrl-0 = <&sdhi1_pins>;
653	pinctrl-1 = <&sdhi1_pins_uhs>;
654	pinctrl-names = "default", "state_uhs";
655
656	vmmc-supply = <&vcc_sdhi1>;
657	vqmmc-supply = <&vccq_sdhi1>;
658	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
659	wp-gpios = <&gpio6 15 GPIO_ACTIVE_HIGH>;
660	sd-uhs-sdr50;
661	status = "okay";
662};
663
664&sdhi2 {
665	pinctrl-0 = <&sdhi2_pins>;
666	pinctrl-1 = <&sdhi2_pins_uhs>;
667	pinctrl-names = "default", "state_uhs";
668
669	vmmc-supply = <&vcc_sdhi2>;
670	vqmmc-supply = <&vccq_sdhi2>;
671	cd-gpios = <&gpio6 22 GPIO_ACTIVE_LOW>;
672	sd-uhs-sdr50;
673	status = "okay";
674};
675
676&qspi {
677	pinctrl-0 = <&qspi_pins>;
678	pinctrl-names = "default";
679
680	status = "okay";
681
682	flash@0 {
683		compatible = "spansion,s25fl512s", "jedec,spi-nor";
684		reg = <0>;
685		spi-max-frequency = <30000000>;
686		spi-tx-bus-width = <4>;
687		spi-rx-bus-width = <4>;
688		spi-cpol;
689		spi-cpha;
690		m25p,fast-read;
691
692		partitions {
693			compatible = "fixed-partitions";
694			#address-cells = <1>;
695			#size-cells = <1>;
696
697			partition@0 {
698				label = "loader";
699				reg = <0x00000000 0x00040000>;
700				read-only;
701			};
702			partition@40000 {
703				label = "user";
704				reg = <0x00040000 0x00400000>;
705				read-only;
706			};
707			partition@440000 {
708				label = "flash";
709				reg = <0x00440000 0x03bc0000>;
710			};
711		};
712	};
713};
714
715&i2c2 {
716	pinctrl-0 = <&i2c2_pins>;
717	pinctrl-names = "i2c-hdmi";
718
719	status = "okay";
720	clock-frequency = <100000>;
721
722};
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
723
724&i2c6 {
725	pinctrl-names = "default";
726	pinctrl-0 = <&pmic_irq_pins>;
727	status = "okay";
728	clock-frequency = <100000>;
729
730	pmic@58 {
731		compatible = "dlg,da9063";
732		reg = <0x58>;
733		interrupt-parent = <&irqc0>;
734		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
735		interrupt-controller;
736
737		rtc {
738			compatible = "dlg,da9063-rtc";
739		};
 
 
 
740
741		wdt {
742			compatible = "dlg,da9063-watchdog";
 
 
 
 
743		};
744	};
745
746	vdd_dvfs: regulator@68 {
747		compatible = "dlg,da9210";
748		reg = <0x68>;
749		interrupt-parent = <&irqc0>;
750		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
751
752		regulator-min-microvolt = <1000000>;
753		regulator-max-microvolt = <1000000>;
754		regulator-boot-on;
755		regulator-always-on;
756	};
757};
758
759&i2c4 {
760	pinctrl-0 = <&i2c4_pins>;
761	pinctrl-names = "i2c-exio4";
762};
763
764&rcar_sound {
765	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
766	pinctrl-names = "default";
767
768	/* Single DAI */
769	#sound-dai-cells = <0>;
770
771	status = "okay";
772
773	rcar_sound,dai {
774		dai0 {
775			playback = <&ssi0>, <&src2>, <&dvc0>;
776			capture  = <&ssi1>, <&src3>, <&dvc1>;
777		};
778	};
779};
780
781&ssi1 {
782	shared-pin;
783};
784
785/* HDMI video input */
786&vin0 {
787	status = "okay";
788	pinctrl-0 = <&vin0_pins>;
789	pinctrl-names = "default";
790
791	port {
792		vin0ep2: endpoint {
793			remote-endpoint = <&adv7612_out>;
794			bus-width = <24>;
795			hsync-active = <0>;
796			vsync-active = <0>;
797			pclk-sample = <1>;
798			data-active = <1>;
799		};
800	};
801};
802
803/* composite video input */
804&vin1 {
805	pinctrl-0 = <&vin1_pins>;
806	pinctrl-names = "default";
807
808	status = "okay";
809
810	port {
811		vin1ep: endpoint {
812			remote-endpoint = <&adv7180_out>;
813			bus-width = <8>;
814		};
815	};
816};
v4.6
 
  1/*
  2 * Device Tree Source for the Gose board
  3 *
  4 * Copyright (C) 2014-2015 Renesas Electronics Corporation
  5 *
  6 * This file is licensed under the terms of the GNU General Public License
  7 * version 2.  This program is licensed "as is" without any warranty of any
  8 * kind, whether express or implied.
  9 */
 10
 11/*
 12 * SSI-AK4643
 13 *
 14 * SW1: 1: AK4643
 15 *      2: CN22
 16 *      3: ADV7511
 17 *
 18 * This command is required when Playback/Capture
 19 *
 20 *	amixer set "LINEOUT Mixer DACL" on
 21 *	amixer set "DVC Out" 100%
 22 *	amixer set "DVC In" 100%
 23 *
 24 * You can use Mute
 25 *
 26 *	amixer set "DVC Out Mute" on
 27 *	amixer set "DVC In Mute" on
 28 *
 29 * You can use Volume Ramp
 30 *
 31 *	amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
 32 *	amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
 33 *	amixer set "DVC Out Ramp" on
 34 *	aplay xxx.wav &
 35 *	amixer set "DVC Out"  80%  // Volume Down
 36 *	amixer set "DVC Out" 100%  // Volume Up
 37 */
 38
 39/dts-v1/;
 40#include "r8a7793.dtsi"
 41#include <dt-bindings/gpio/gpio.h>
 42#include <dt-bindings/input/input.h>
 43
 44/ {
 45	model = "Gose";
 46	compatible = "renesas,gose", "renesas,r8a7793";
 47
 48	aliases {
 49		serial0 = &scif0;
 50		serial1 = &scif1;
 
 
 
 
 
 
 
 51	};
 52
 53	chosen {
 54		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
 55		stdout-path = "serial0:115200n8";
 56	};
 57
 58	memory@40000000 {
 59		device_type = "memory";
 60		reg = <0 0x40000000 0 0x40000000>;
 61	};
 62
 63	gpio-keys {
 64		compatible = "gpio-keys";
 65
 
 
 
 66		key-1 {
 67		        gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
 68		        linux,code = <KEY_1>;
 69		        label = "SW2-1";
 70		        wakeup-source;
 71		        debounce-interval = <20>;
 72		};
 73		key-2 {
 74		        gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
 75		        linux,code = <KEY_2>;
 76		        label = "SW2-2";
 77		        wakeup-source;
 78		        debounce-interval = <20>;
 79		};
 80		key-3 {
 81		        gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
 82		        linux,code = <KEY_3>;
 83		        label = "SW2-3";
 84		        wakeup-source;
 85		        debounce-interval = <20>;
 86		};
 87		key-4 {
 88		        gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
 89		        linux,code = <KEY_4>;
 90		        label = "SW2-4";
 91		        wakeup-source;
 92		        debounce-interval = <20>;
 93		};
 94		key-a {
 95		        gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
 96		        linux,code = <KEY_A>;
 97		        label = "SW30";
 98		        wakeup-source;
 99		        debounce-interval = <20>;
100		};
101		key-b {
102		        gpios = <&gpio7 1 GPIO_ACTIVE_LOW>;
103		        linux,code = <KEY_B>;
104		        label = "SW31";
105		        wakeup-source;
106		        debounce-interval = <20>;
107		};
108		key-c {
109		        gpios = <&gpio7 2 GPIO_ACTIVE_LOW>;
110		        linux,code = <KEY_C>;
111		        label = "SW32";
112		        wakeup-source;
113		        debounce-interval = <20>;
114		};
115		key-d {
116		        gpios = <&gpio7 3 GPIO_ACTIVE_LOW>;
117		        linux,code = <KEY_D>;
118		        label = "SW33";
119		        wakeup-source;
120		        debounce-interval = <20>;
121		};
122		key-e {
123		        gpios = <&gpio7 4 GPIO_ACTIVE_LOW>;
124		        linux,code = <KEY_E>;
125		        label = "SW34";
126		        wakeup-source;
127		        debounce-interval = <20>;
128		};
129		key-f {
130		        gpios = <&gpio7 5 GPIO_ACTIVE_LOW>;
131		        linux,code = <KEY_F>;
132		        label = "SW35";
133		        wakeup-source;
134		        debounce-interval = <20>;
135		};
136		key-g {
137		        gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
138		        linux,code = <KEY_G>;
139		        label = "SW36";
140		        wakeup-source;
141		        debounce-interval = <20>;
142		};
143	};
144
145	leds {
146		compatible = "gpio-leds";
147		led6 {
148			gpios = <&gpio2 19 GPIO_ACTIVE_HIGH>;
149			label = "LED6";
150		};
151		led7 {
152			gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
153			label = "LED7";
154		};
155		led8 {
156			gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>;
157			label = "LED8";
158		};
159	};
160
161	audio_clock: clock {
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
162		compatible = "fixed-clock";
163		#clock-cells = <0>;
164		clock-frequency = <11289600>;
165		clock-output-names = "audio_clock";
166	};
167
168	rsnd_ak4643: sound {
169		compatible = "simple-audio-card";
170
171		simple-audio-card,format = "left_j";
172		simple-audio-card,bitclock-master = <&sndcodec>;
173		simple-audio-card,frame-master = <&sndcodec>;
174
175		sndcpu: simple-audio-card,cpu {
176			sound-dai = <&rcar_sound>;
177		};
178
179		sndcodec: simple-audio-card,codec {
180			sound-dai = <&ak4643>;
181			clocks = <&audio_clock>;
182		};
183	};
184
 
 
 
 
 
 
 
 
 
 
 
185	hdmi-out {
186		compatible = "hdmi-connector";
187		type = "a";
188
189		port {
190			hdmi_con: endpoint {
191				remote-endpoint = <&adv7511_out>;
192			};
193		};
194	};
195
 
 
 
 
 
 
 
 
 
 
196	x2_clk: x2-clock {
197		compatible = "fixed-clock";
198		#clock-cells = <0>;
199		clock-frequency = <74250000>;
200	};
201
202	x13_clk: x13-clock {
203		compatible = "fixed-clock";
204		#clock-cells = <0>;
205		clock-frequency = <148500000>;
206	};
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
207};
208
209&du {
210	pinctrl-0 = <&du_pins>;
211	pinctrl-names = "default";
212	status = "okay";
213
214	clocks = <&mstp7_clks R8A7793_CLK_DU0>,
215		 <&mstp7_clks R8A7793_CLK_DU1>,
216		 <&mstp7_clks R8A7793_CLK_LVDS0>,
217		 <&x13_clk>, <&x2_clk>;
218	clock-names = "du.0", "du.1", "lvds.0",
219		      "dclkin.0", "dclkin.1";
220
221	ports {
222		port@0 {
223			endpoint {
224				remote-endpoint = <&adv7511_in>;
225			};
226		};
 
 
 
 
 
227		port@1 {
228			lvds_connector: endpoint {
229			};
230		};
231	};
232};
233
234&extal_clk {
235	clock-frequency = <20000000>;
236};
237
238&pfc {
239	pinctrl-0 = <&scif_clk_pins>;
240	pinctrl-names = "default";
241
242	i2c2_pins: i2c2 {
243		renesas,groups = "i2c2";
244		renesas,function = "i2c2";
 
 
 
 
 
245	};
246
247	du_pins: du {
248		renesas,groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
249		renesas,function = "du";
250	};
251
252	scif0_pins: serial0 {
253		renesas,groups = "scif0_data_d";
254		renesas,function = "scif0";
255	};
256
257	scif1_pins: serial1 {
258		renesas,groups = "scif1_data_d";
259		renesas,function = "scif1";
260	};
261
262	scif_clk_pins: scif_clk {
263		renesas,groups = "scif_clk";
264		renesas,function = "scif_clk";
265	};
266
267	ether_pins: ether {
268		renesas,groups = "eth_link", "eth_mdio", "eth_rmii";
269		renesas,function = "eth";
270	};
271
272	phy1_pins: phy1 {
273		renesas,groups = "intc_irq0";
274		renesas,function = "intc";
275	};
276
277	qspi_pins: spi0 {
278		renesas,groups = "qspi_ctrl", "qspi_data4";
279		renesas,function = "qspi";
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
280	};
281
282	sound_pins: sound {
283		renesas,groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data";
284		renesas,function = "ssi";
285	};
286
287	sound_clk_pins: sound_clk {
288		renesas,groups = "audio_clk_a";
289		renesas,function = "audio_clk";
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
290	};
291};
292
293&ether {
294	pinctrl-0 = <&ether_pins &phy1_pins>;
295	pinctrl-names = "default";
296
297	phy-handle = <&phy1>;
298	renesas,ether-link-active-low;
299	status = "okay";
300
301	phy1: ethernet-phy@1 {
302		reg = <1>;
303		interrupt-parent = <&irqc0>;
304		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
305		micrel,led-mode = <1>;
 
306	};
307};
308
309&cmt0 {
310	status = "okay";
311};
312
 
 
 
 
 
 
 
 
 
313&scif0 {
314	pinctrl-0 = <&scif0_pins>;
315	pinctrl-names = "default";
316
317	status = "okay";
318};
319
320&scif1 {
321	pinctrl-0 = <&scif1_pins>;
322	pinctrl-names = "default";
323
324	status = "okay";
325};
326
327&scif_clk {
328	clock-frequency = <14745600>;
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
329	status = "okay";
330};
331
332&qspi {
333	pinctrl-0 = <&qspi_pins>;
334	pinctrl-names = "default";
335
336	status = "okay";
337
338	flash@0 {
339		compatible = "spansion,s25fl512s", "jedec,spi-nor";
340		reg = <0>;
341		spi-max-frequency = <30000000>;
342		spi-tx-bus-width = <4>;
343		spi-rx-bus-width = <4>;
344		spi-cpol;
345		spi-cpha;
346		m25p,fast-read;
347
348		partitions {
349			compatible = "fixed-partitions";
350			#address-cells = <1>;
351			#size-cells = <1>;
352
353			partition@0 {
354				label = "loader";
355				reg = <0x00000000 0x00040000>;
356				read-only;
357			};
358			partition@40000 {
359				label = "user";
360				reg = <0x00040000 0x00400000>;
361				read-only;
362			};
363			partition@440000 {
364				label = "flash";
365				reg = <0x00440000 0x03bc0000>;
366			};
367		};
368	};
369};
370
371&i2c2 {
372	pinctrl-0 = <&i2c2_pins>;
373	pinctrl-names = "default";
374
375	status = "okay";
376	clock-frequency = <100000>;
377
378	ak4643: codec@12 {
379		compatible = "asahi-kasei,ak4643";
380		#sound-dai-cells = <0>;
381		reg = <0x12>;
382	};
383
384	hdmi@39 {
385		compatible = "adi,adv7511w";
386		reg = <0x39>;
387		interrupt-parent = <&gpio3>;
388		interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
389
390		adi,input-depth = <8>;
391		adi,input-colorspace = "rgb";
392		adi,input-clock = "1x";
393		adi,input-style = <1>;
394		adi,input-justification = "evenly";
395
396		ports {
397			#address-cells = <1>;
398			#size-cells = <0>;
 
 
 
 
 
 
 
 
 
399
400			port@0 {
401				reg = <0>;
402				adv7511_in: endpoint {
403					remote-endpoint = <&du_out_rgb>;
404				};
405			};
406
407			port@1 {
408				reg = <1>;
409				adv7511_out: endpoint {
410					remote-endpoint = <&hdmi_con>;
411				};
412			};
413		};
414	};
415
416	eeprom@50 {
417		compatible = "renesas,r1ex24002", "atmel,24c02";
418		reg = <0x50>;
419		pagesize = <16>;
 
 
 
 
 
 
420	};
421};
422
 
 
 
 
 
423&rcar_sound {
424	pinctrl-0 = <&sound_pins &sound_clk_pins>;
425	pinctrl-names = "default";
426
427	/* Single DAI */
428	#sound-dai-cells = <0>;
429
430	status = "okay";
431
432	rcar_sound,dai {
433		dai0 {
434			playback = <&ssi0 &src2 &dvc0>;
435			capture  = <&ssi1 &src3 &dvc1>;
436		};
437	};
438};
439
440&ssi1 {
441	shared-pin;
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
442};