Loading...
1/*
2 * BSD LICENSE
3 *
4 * Copyright(c) 2015 Broadcom Corporation. All rights reserved.
5 *
6 * Redistribution and use in source and binary forms, with or without
7 * modification, are permitted provided that the following conditions
8 * are met:
9 *
10 * * Redistributions of source code must retain the above copyright
11 * notice, this list of conditions and the following disclaimer.
12 * * Redistributions in binary form must reproduce the above copyright
13 * notice, this list of conditions and the following disclaimer in
14 * the documentation and/or other materials provided with the
15 * distribution.
16 * * Neither the name of Broadcom Corporation nor the names of its
17 * contributors may be used to endorse or promote products derived
18 * from this software without specific prior written permission.
19 *
20 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
21 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
22 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
23 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
24 * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
25 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
26 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
27 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
28 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
29 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
30 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
31 */
32
33#include <dt-bindings/interrupt-controller/arm-gic.h>
34#include <dt-bindings/interrupt-controller/irq.h>
35#include <dt-bindings/clock/bcm-nsp.h>
36
37/ {
38 #address-cells = <1>;
39 #size-cells = <1>;
40 compatible = "brcm,nsp";
41 model = "Broadcom Northstar Plus SoC";
42 interrupt-parent = <&gic>;
43
44 aliases {
45 serial0 = &uart0;
46 serial1 = &uart1;
47 ethernet0 = &amac0;
48 ethernet1 = &amac1;
49 ethernet2 = &amac2;
50 };
51
52 cpus {
53 #address-cells = <1>;
54 #size-cells = <0>;
55
56 cpu0: cpu@0 {
57 device_type = "cpu";
58 compatible = "arm,cortex-a9";
59 next-level-cache = <&L2>;
60 reg = <0x0>;
61 };
62
63 cpu1: cpu@1 {
64 device_type = "cpu";
65 compatible = "arm,cortex-a9";
66 next-level-cache = <&L2>;
67 enable-method = "brcm,bcm-nsp-smp";
68 secondary-boot-reg = <0xffff0fec>;
69 reg = <0x1>;
70 };
71 };
72
73 pmu {
74 compatible = "arm,cortex-a9-pmu";
75 interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH
76 GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
77 interrupt-affinity = <&cpu0>, <&cpu1>;
78 };
79
80 mpcore@19000000 {
81 compatible = "simple-bus";
82 ranges = <0x00000000 0x19000000 0x00023000>;
83 #address-cells = <1>;
84 #size-cells = <1>;
85
86 a9pll: arm_clk@0 {
87 #clock-cells = <0>;
88 compatible = "brcm,nsp-armpll";
89 clocks = <&osc>;
90 reg = <0x00000 0x1000>;
91 };
92
93 timer@20200 {
94 compatible = "arm,cortex-a9-global-timer";
95 reg = <0x20200 0x100>;
96 interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
97 clocks = <&periph_clk>;
98 };
99
100 twd-timer@20600 {
101 compatible = "arm,cortex-a9-twd-timer";
102 reg = <0x20600 0x20>;
103 interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
104 IRQ_TYPE_EDGE_RISING)>;
105 clocks = <&periph_clk>;
106 };
107
108 twd-watchdog@20620 {
109 compatible = "arm,cortex-a9-twd-wdt";
110 reg = <0x20620 0x20>;
111 interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
112 IRQ_TYPE_LEVEL_HIGH)>;
113 clocks = <&periph_clk>;
114 };
115
116 gic: interrupt-controller@21000 {
117 compatible = "arm,cortex-a9-gic";
118 #interrupt-cells = <3>;
119 #address-cells = <0>;
120 interrupt-controller;
121 reg = <0x21000 0x1000>,
122 <0x20100 0x100>;
123 };
124
125 L2: cache-controller@22000 {
126 compatible = "arm,pl310-cache";
127 reg = <0x22000 0x1000>;
128 cache-unified;
129 cache-level = <2>;
130 };
131 };
132
133 clocks {
134 #address-cells = <1>;
135 #size-cells = <1>;
136 ranges;
137
138 osc: oscillator {
139 #clock-cells = <0>;
140 compatible = "fixed-clock";
141 clock-frequency = <25000000>;
142 };
143
144 iprocmed: iprocmed {
145 #clock-cells = <0>;
146 compatible = "fixed-factor-clock";
147 clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
148 clock-div = <2>;
149 clock-mult = <1>;
150 };
151
152 iprocslow: iprocslow {
153 #clock-cells = <0>;
154 compatible = "fixed-factor-clock";
155 clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
156 clock-div = <4>;
157 clock-mult = <1>;
158 };
159
160 periph_clk: periph_clk {
161 #clock-cells = <0>;
162 compatible = "fixed-factor-clock";
163 clocks = <&a9pll>;
164 clock-div = <2>;
165 clock-mult = <1>;
166 };
167 };
168
169 axi@18000000 {
170 compatible = "simple-bus";
171 ranges = <0x00000000 0x18000000 0x0011c40c>;
172 #address-cells = <1>;
173 #size-cells = <1>;
174
175 gpioa: gpio@20 {
176 compatible = "brcm,nsp-gpio-a";
177 reg = <0x0020 0x70>,
178 <0x3f1c4 0x1c>;
179 #gpio-cells = <2>;
180 gpio-controller;
181 ngpios = <32>;
182 interrupt-controller;
183 interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
184 gpio-ranges = <&pinctrl 0 0 32>;
185 };
186
187 uart0: serial@300 {
188 compatible = "ns16550a";
189 reg = <0x0300 0x100>;
190 interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
191 clocks = <&osc>;
192 status = "disabled";
193 };
194
195 uart1: serial@400 {
196 compatible = "ns16550a";
197 reg = <0x0400 0x100>;
198 interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
199 clocks = <&osc>;
200 status = "disabled";
201 };
202
203 dma: dma@20000 {
204 compatible = "arm,pl330", "arm,primecell";
205 reg = <0x20000 0x1000>;
206 interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
207 <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
208 <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
209 <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
210 <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
211 <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
212 <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
213 <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
214 <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
215 clocks = <&iprocslow>;
216 clock-names = "apb_pclk";
217 #dma-cells = <1>;
218 dma-coherent;
219 status = "disabled";
220 };
221
222 sdio: sdhci@21000 {
223 compatible = "brcm,sdhci-iproc-cygnus";
224 reg = <0x21000 0x100>;
225 interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
226 sdhci,auto-cmd12;
227 clocks = <&lcpll0 BCM_NSP_LCPLL0_SDIO_CLK>;
228 dma-coherent;
229 status = "disabled";
230 };
231
232 amac0: ethernet@22000 {
233 compatible = "brcm,nsp-amac";
234 reg = <0x022000 0x1000>,
235 <0x110000 0x1000>;
236 reg-names = "amac_base", "idm_base";
237 interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
238 dma-coherent;
239 status = "disabled";
240 };
241
242 amac1: ethernet@23000 {
243 compatible = "brcm,nsp-amac";
244 reg = <0x023000 0x1000>,
245 <0x111000 0x1000>;
246 reg-names = "amac_base", "idm_base";
247 interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
248 dma-coherent;
249 status = "disabled";
250 };
251
252 amac2: ethernet@24000 {
253 compatible = "brcm,nsp-amac";
254 reg = <0x024000 0x1000>,
255 <0x112000 0x1000>;
256 reg-names = "amac_base", "idm_base";
257 interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
258 dma-coherent;
259 status = "disabled";
260 };
261
262 mailbox: mailbox@25c00 {
263 compatible = "brcm,iproc-fa2-mbox";
264 reg = <0x25c00 0x400>;
265 interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
266 #mbox-cells = <1>;
267 brcm,rx-status-len = <32>;
268 brcm,use-bcm-hdr;
269 dma-coherent;
270 };
271
272 nand_controller: nand-controller@26000 {
273 compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
274 reg = <0x026000 0x600>,
275 <0x11b408 0x600>,
276 <0x026f00 0x20>;
277 reg-names = "nand", "iproc-idm", "iproc-ext";
278 interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
279
280 #address-cells = <1>;
281 #size-cells = <0>;
282
283 brcm,nand-has-wp;
284 };
285
286 qspi: spi@27200 {
287 compatible = "brcm,spi-nsp-qspi", "brcm,spi-bcm-qspi";
288 reg = <0x027200 0x184>,
289 <0x027000 0x124>,
290 <0x11c408 0x004>,
291 <0x0273a0 0x01c>;
292 reg-names = "mspi", "bspi", "intr_regs",
293 "intr_status_reg";
294 interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
295 <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
296 <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
297 <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
298 <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
299 <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
300 <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
301 interrupt-names = "spi_lr_fullness_reached",
302 "spi_lr_session_aborted",
303 "spi_lr_impatient",
304 "spi_lr_session_done",
305 "spi_lr_overhead",
306 "mspi_done",
307 "mspi_halted";
308 clocks = <&iprocmed>;
309 clock-names = "iprocmed";
310 num-cs = <2>;
311 #address-cells = <1>;
312 #size-cells = <0>;
313 };
314
315 xhci: usb@29000 {
316 compatible = "generic-xhci";
317 reg = <0x29000 0x1000>;
318 interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
319 phys = <&usb3_phy>;
320 phy-names = "usb3-phy";
321 dma-coherent;
322 status = "disabled";
323 };
324
325 ehci0: usb@2a000 {
326 compatible = "generic-ehci";
327 reg = <0x2a000 0x100>;
328 interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
329 dma-coherent;
330 status = "disabled";
331 };
332
333 ohci0: usb@2b000 {
334 compatible = "generic-ohci";
335 reg = <0x2b000 0x100>;
336 interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
337 dma-coherent;
338 status = "disabled";
339 };
340
341 crypto@2f000 {
342 compatible = "brcm,spum-nsp-crypto";
343 reg = <0x2f000 0x900>;
344 mboxes = <&mailbox 0>;
345 };
346
347 gpiob: gpio@30000 {
348 compatible = "brcm,iproc-nsp-gpio", "brcm,iproc-gpio";
349 reg = <0x30000 0x50>;
350 #gpio-cells = <2>;
351 gpio-controller;
352 ngpios = <4>;
353 interrupt-controller;
354 interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
355 };
356
357 pwm: pwm@31000 {
358 compatible = "brcm,iproc-pwm";
359 reg = <0x31000 0x28>;
360 clocks = <&osc>;
361 #pwm-cells = <3>;
362 status = "disabled";
363 };
364
365 rng: rng@33000 {
366 compatible = "brcm,bcm-nsp-rng";
367 reg = <0x33000 0x14>;
368 };
369
370 ccbtimer0: timer@34000 {
371 compatible = "arm,sp804", "arm,primecell";
372 reg = <0x34000 0x1000>;
373 interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
374 <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
375 clocks = <&iprocslow>;
376 clock-names = "apb_pclk";
377 };
378
379 ccbtimer1: timer@35000 {
380 compatible = "arm,sp804", "arm,primecell";
381 reg = <0x35000 0x1000>;
382 interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
383 <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
384 clocks = <&iprocslow>;
385 clock-names = "apb_pclk";
386 };
387
388 srab: ethernet-switch@36000 {
389 compatible = "brcm,nsp-srab";
390 reg = <0x36000 0x1000>,
391 <0x3f308 0x8>,
392 <0x3f410 0xc>;
393 reg-names = "srab", "mux_config", "sgmii_config";
394 interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
395 <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
396 <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
397 <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
398 <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
399 <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
400 <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
401 <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
402 <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
403 <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
404 <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
405 <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
406 <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
407 interrupt-names = "link_state_p0",
408 "link_state_p1",
409 "link_state_p2",
410 "link_state_p3",
411 "link_state_p4",
412 "link_state_p5",
413 "link_state_p7",
414 "link_state_p8",
415 "phy",
416 "ts",
417 "imp_sleep_timer_p5",
418 "imp_sleep_timer_p7",
419 "imp_sleep_timer_p8";
420 status = "disabled";
421
422 /* ports are defined in board DTS */
423 ports {
424 #address-cells = <1>;
425 #size-cells = <0>;
426 };
427 };
428
429 i2c0: i2c@38000 {
430 compatible = "brcm,iproc-i2c";
431 reg = <0x38000 0x50>;
432 #address-cells = <1>;
433 #size-cells = <0>;
434 interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
435 clock-frequency = <100000>;
436 dma-coherent;
437 status = "disabled";
438 };
439
440 watchdog@39000 {
441 compatible = "arm,sp805", "arm,primecell";
442 reg = <0x39000 0x1000>;
443 interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
444 clocks = <&iprocslow>, <&iprocslow>;
445 clock-names = "wdog_clk", "apb_pclk";
446 };
447
448 lcpll0: lcpll0@3f100 {
449 #clock-cells = <1>;
450 compatible = "brcm,nsp-lcpll0";
451 reg = <0x3f100 0x14>;
452 clocks = <&osc>;
453 clock-output-names = "lcpll0", "pcie_phy", "sdio",
454 "ddr_phy";
455 };
456
457 genpll: genpll@3f140 {
458 #clock-cells = <1>;
459 compatible = "brcm,nsp-genpll";
460 reg = <0x3f140 0x24>;
461 clocks = <&osc>;
462 clock-output-names = "genpll", "phy", "ethernetclk",
463 "usbclk", "iprocfast", "sata1",
464 "sata2";
465 };
466
467 pinctrl: pinctrl@3f1c0 {
468 compatible = "brcm,nsp-pinmux";
469 reg = <0x3f1c0 0x04>,
470 <0x30028 0x04>,
471 <0x3f408 0x04>;
472 };
473
474 thermal: thermal@3f2c0 {
475 compatible = "brcm,ns-thermal";
476 reg = <0x3f2c0 0x10>;
477 #thermal-sensor-cells = <0>;
478 };
479
480 sata_phy: sata_phy@40100 {
481 compatible = "brcm,iproc-nsp-sata-phy";
482 reg = <0x40100 0x340>;
483 reg-names = "phy";
484 #address-cells = <1>;
485 #size-cells = <0>;
486
487 sata_phy0: sata-phy@0 {
488 reg = <0>;
489 #phy-cells = <0>;
490 status = "disabled";
491 };
492
493 sata_phy1: sata-phy@1 {
494 reg = <1>;
495 #phy-cells = <0>;
496 status = "disabled";
497 };
498 };
499
500 sata: ahci@41000 {
501 compatible = "brcm,bcm-nsp-ahci";
502 reg-names = "ahci", "top-ctrl";
503 reg = <0x41000 0x1000>, <0x40020 0x1c>;
504 interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
505 #address-cells = <1>;
506 #size-cells = <0>;
507 dma-coherent;
508 status = "disabled";
509
510 sata0: sata-port@0 {
511 reg = <0>;
512 phys = <&sata_phy0>;
513 phy-names = "sata-phy";
514 };
515
516 sata1: sata-port@1 {
517 reg = <1>;
518 phys = <&sata_phy1>;
519 phy-names = "sata-phy";
520 };
521 };
522
523 usb3_phy: usb3-phy@104000 {
524 compatible = "brcm,ns-bx-usb3-phy";
525 reg = <0x104000 0x1000>,
526 <0x032000 0x1000>;
527 reg-names = "dmp", "ccb-mii";
528 #phy-cells = <0>;
529 status = "disabled";
530 };
531 };
532
533 pcie0: pcie@18012000 {
534 compatible = "brcm,iproc-pcie";
535 reg = <0x18012000 0x1000>;
536
537 #interrupt-cells = <1>;
538 interrupt-map-mask = <0 0 0 0>;
539 interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
540
541 linux,pci-domain = <0>;
542
543 bus-range = <0x00 0xff>;
544
545 #address-cells = <3>;
546 #size-cells = <2>;
547 device_type = "pci";
548
549 /* Note: The HW does not support I/O resources. So,
550 * only the memory resource range is being specified.
551 */
552 ranges = <0x82000000 0 0x08000000 0x08000000 0 0x8000000>;
553
554 dma-coherent;
555 status = "disabled";
556
557 msi-parent = <&msi0>;
558 msi0: msi-controller {
559 compatible = "brcm,iproc-msi";
560 msi-controller;
561 interrupt-parent = <&gic>;
562 interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
563 <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
564 <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
565 <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
566 brcm,pcie-msi-inten;
567 };
568 };
569
570 pcie1: pcie@18013000 {
571 compatible = "brcm,iproc-pcie";
572 reg = <0x18013000 0x1000>;
573
574 #interrupt-cells = <1>;
575 interrupt-map-mask = <0 0 0 0>;
576 interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
577
578 linux,pci-domain = <1>;
579
580 bus-range = <0x00 0xff>;
581
582 #address-cells = <3>;
583 #size-cells = <2>;
584 device_type = "pci";
585
586 /* Note: The HW does not support I/O resources. So,
587 * only the memory resource range is being specified.
588 */
589 ranges = <0x82000000 0 0x40000000 0x40000000 0 0x8000000>;
590
591 dma-coherent;
592 status = "disabled";
593
594 msi-parent = <&msi1>;
595 msi1: msi-controller {
596 compatible = "brcm,iproc-msi";
597 msi-controller;
598 interrupt-parent = <&gic>;
599 interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
600 <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
601 <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
602 <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
603 brcm,pcie-msi-inten;
604 };
605 };
606
607 pcie2: pcie@18014000 {
608 compatible = "brcm,iproc-pcie";
609 reg = <0x18014000 0x1000>;
610
611 #interrupt-cells = <1>;
612 interrupt-map-mask = <0 0 0 0>;
613 interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
614
615 linux,pci-domain = <2>;
616
617 bus-range = <0x00 0xff>;
618
619 #address-cells = <3>;
620 #size-cells = <2>;
621 device_type = "pci";
622
623 /* Note: The HW does not support I/O resources. So,
624 * only the memory resource range is being specified.
625 */
626 ranges = <0x82000000 0 0x48000000 0x48000000 0 0x8000000>;
627
628 dma-coherent;
629 status = "disabled";
630
631 msi-parent = <&msi2>;
632 msi2: msi-controller {
633 compatible = "brcm,iproc-msi";
634 msi-controller;
635 interrupt-parent = <&gic>;
636 interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>,
637 <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
638 <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
639 <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
640 brcm,pcie-msi-inten;
641 };
642 };
643
644 thermal-zones {
645 cpu-thermal {
646 polling-delay-passive = <0>;
647 polling-delay = <1000>;
648 coefficients = <(-556) 418000>;
649 thermal-sensors = <&thermal>;
650
651 trips {
652 cpu-crit {
653 temperature = <125000>;
654 hysteresis = <0>;
655 type = "critical";
656 };
657 };
658
659 cooling-maps {
660 };
661 };
662 };
663};
1/*
2 * BSD LICENSE
3 *
4 * Copyright(c) 2015 Broadcom Corporation. All rights reserved.
5 *
6 * Redistribution and use in source and binary forms, with or without
7 * modification, are permitted provided that the following conditions
8 * are met:
9 *
10 * * Redistributions of source code must retain the above copyright
11 * notice, this list of conditions and the following disclaimer.
12 * * Redistributions in binary form must reproduce the above copyright
13 * notice, this list of conditions and the following disclaimer in
14 * the documentation and/or other materials provided with the
15 * distribution.
16 * * Neither the name of Broadcom Corporation nor the names of its
17 * contributors may be used to endorse or promote products derived
18 * from this software without specific prior written permission.
19 *
20 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
21 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
22 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
23 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
24 * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
25 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
26 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
27 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
28 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
29 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
30 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
31 */
32
33#include <dt-bindings/interrupt-controller/arm-gic.h>
34#include <dt-bindings/interrupt-controller/irq.h>
35#include <dt-bindings/clock/bcm-nsp.h>
36
37#include "skeleton.dtsi"
38
39/ {
40 compatible = "brcm,nsp";
41 model = "Broadcom Northstar Plus SoC";
42 interrupt-parent = <&gic>;
43
44 cpus {
45 #address-cells = <1>;
46 #size-cells = <0>;
47
48 cpu0: cpu@0 {
49 device_type = "cpu";
50 compatible = "arm,cortex-a9";
51 next-level-cache = <&L2>;
52 reg = <0x0>;
53 };
54
55 cpu1: cpu@1 {
56 device_type = "cpu";
57 compatible = "arm,cortex-a9";
58 next-level-cache = <&L2>;
59 enable-method = "brcm,bcm-nsp-smp";
60 secondary-boot-reg = <0xffff0fec>;
61 reg = <0x1>;
62 };
63 };
64
65 pmu {
66 compatible = "arm,cortex-a9-pmu";
67 interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH
68 GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
69 interrupt-affinity = <&cpu0>, <&cpu1>;
70 };
71
72 mpcore {
73 compatible = "simple-bus";
74 ranges = <0x00000000 0x19000000 0x00023000>;
75 #address-cells = <1>;
76 #size-cells = <1>;
77
78 a9pll: arm_clk@00000 {
79 #clock-cells = <0>;
80 compatible = "brcm,nsp-armpll";
81 clocks = <&osc>;
82 reg = <0x00000 0x1000>;
83 };
84
85 timer@20200 {
86 compatible = "arm,cortex-a9-global-timer";
87 reg = <0x20200 0x100>;
88 interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
89 clocks = <&periph_clk>;
90 };
91
92 twd-timer@20600 {
93 compatible = "arm,cortex-a9-twd-timer";
94 reg = <0x20600 0x20>;
95 interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
96 IRQ_TYPE_LEVEL_HIGH)>;
97 clocks = <&periph_clk>;
98 };
99
100 twd-watchdog@20620 {
101 compatible = "arm,cortex-a9-twd-wdt";
102 reg = <0x20620 0x20>;
103 interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
104 IRQ_TYPE_LEVEL_HIGH)>;
105 clocks = <&periph_clk>;
106 };
107
108 gic: interrupt-controller@21000 {
109 compatible = "arm,cortex-a9-gic";
110 #interrupt-cells = <3>;
111 #address-cells = <0>;
112 interrupt-controller;
113 reg = <0x21000 0x1000>,
114 <0x20100 0x100>;
115 };
116
117 L2: l2-cache {
118 compatible = "arm,pl310-cache";
119 reg = <0x22000 0x1000>;
120 cache-unified;
121 cache-level = <2>;
122 };
123 };
124
125 clocks {
126 #address-cells = <1>;
127 #size-cells = <1>;
128 ranges;
129
130 osc: oscillator {
131 #clock-cells = <0>;
132 compatible = "fixed-clock";
133 clock-frequency = <25000000>;
134 };
135
136 iprocmed: iprocmed {
137 #clock-cells = <0>;
138 compatible = "fixed-factor-clock";
139 clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
140 clock-div = <2>;
141 clock-mult = <1>;
142 };
143
144 iprocslow: iprocslow {
145 #clock-cells = <0>;
146 compatible = "fixed-factor-clock";
147 clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
148 clock-div = <4>;
149 clock-mult = <1>;
150 };
151
152 periph_clk: periph_clk {
153 #clock-cells = <0>;
154 compatible = "fixed-factor-clock";
155 clocks = <&a9pll>;
156 clock-div = <2>;
157 clock-mult = <1>;
158 };
159 };
160
161 axi {
162 compatible = "simple-bus";
163 ranges = <0x00000000 0x18000000 0x0011c40c>;
164 #address-cells = <1>;
165 #size-cells = <1>;
166
167 gpioa: gpio@0020 {
168 compatible = "brcm,nsp-gpio-a";
169 reg = <0x0020 0x70>,
170 <0x3f1c4 0x1c>;
171 #gpio-cells = <2>;
172 gpio-controller;
173 ngpios = <32>;
174 interrupt-controller;
175 interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
176 gpio-ranges = <&pinctrl 0 0 32>;
177 };
178
179 uart0: serial@0300 {
180 compatible = "ns16550a";
181 reg = <0x0300 0x100>;
182 interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
183 clocks = <&osc>;
184 status = "disabled";
185 };
186
187 uart1: serial@0400 {
188 compatible = "ns16550a";
189 reg = <0x0400 0x100>;
190 interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
191 clocks = <&osc>;
192 status = "disabled";
193 };
194
195 dma@20000 {
196 compatible = "arm,pl330", "arm,primecell";
197 reg = <0x20000 0x1000>;
198 interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
199 <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
200 <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
201 <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
202 <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
203 <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
204 <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
205 <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
206 <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
207 clocks = <&iprocslow>;
208 clock-names = "apb_pclk";
209 #dma-cells = <1>;
210 };
211
212 amac0: ethernet@22000 {
213 compatible = "brcm,nsp-amac";
214 reg = <0x022000 0x1000>,
215 <0x110000 0x1000>;
216 reg-names = "amac_base", "idm_base";
217 interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
218 status = "disabled";
219 };
220
221 amac1: ethernet@23000 {
222 compatible = "brcm,nsp-amac";
223 reg = <0x023000 0x1000>,
224 <0x111000 0x1000>;
225 reg-names = "amac_base", "idm_base";
226 interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
227 status = "disabled";
228 };
229
230 nand: nand@26000 {
231 compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
232 reg = <0x026000 0x600>,
233 <0x11b408 0x600>,
234 <0x026f00 0x20>;
235 reg-names = "nand", "iproc-idm", "iproc-ext";
236 interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
237
238 #address-cells = <1>;
239 #size-cells = <0>;
240
241 brcm,nand-has-wp;
242 };
243
244 gpiob: gpio@30000 {
245 compatible = "brcm,iproc-nsp-gpio", "brcm,iproc-gpio";
246 reg = <0x30000 0x50>;
247 #gpio-cells = <2>;
248 gpio-controller;
249 ngpios = <4>;
250 interrupt-controller;
251 interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
252 };
253
254 pwm: pwm@31000 {
255 compatible = "brcm,iproc-pwm";
256 reg = <0x31000 0x28>;
257 clocks = <&osc>;
258 #pwm-cells = <3>;
259 status = "disabled";
260 };
261
262 rng: rng@33000 {
263 compatible = "brcm,bcm-nsp-rng";
264 reg = <0x33000 0x14>;
265 };
266
267 qspi: qspi@27200 {
268 compatible = "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi";
269 reg = <0x027200 0x184>,
270 <0x027000 0x124>,
271 <0x11c408 0x004>,
272 <0x0273a0 0x01c>;
273 reg-names = "mspi", "bspi", "intr_regs",
274 "intr_status_reg";
275 interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
276 <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
277 <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
278 <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
279 <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
280 <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
281 <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
282 interrupt-names = "spi_lr_fullness_reached",
283 "spi_lr_session_aborted",
284 "spi_lr_impatient",
285 "spi_lr_session_done",
286 "spi_lr_overhead",
287 "mspi_done",
288 "mspi_halted";
289 clocks = <&iprocmed>;
290 clock-names = "iprocmed";
291 num-cs = <2>;
292 #address-cells = <1>;
293 #size-cells = <0>;
294 };
295
296 ccbtimer0: timer@34000 {
297 compatible = "arm,sp804";
298 reg = <0x34000 0x1000>;
299 interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
300 <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
301 clocks = <&iprocslow>;
302 clock-names = "apb_pclk";
303 };
304
305 ccbtimer1: timer@35000 {
306 compatible = "arm,sp804";
307 reg = <0x35000 0x1000>;
308 interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
309 <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
310 clocks = <&iprocslow>;
311 clock-names = "apb_pclk";
312 };
313
314 srab: srab@36000 {
315 compatible = "brcm,nsp-srab";
316 reg = <0x36000 0x1000>;
317 #address-cells = <1>;
318 #size-cells = <0>;
319
320 status = "disabled";
321
322 /* ports are defined in board DTS */
323 };
324
325 i2c0: i2c@38000 {
326 compatible = "brcm,iproc-i2c";
327 reg = <0x38000 0x50>;
328 #address-cells = <1>;
329 #size-cells = <0>;
330 interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>;
331 clock-frequency = <100000>;
332 };
333
334 watchdog@39000 {
335 compatible = "arm,sp805", "arm,primecell";
336 reg = <0x39000 0x1000>;
337 interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
338 clocks = <&iprocslow>, <&iprocslow>;
339 clock-names = "wdogclk", "apb_pclk";
340 };
341
342 lcpll0: lcpll0@3f100 {
343 #clock-cells = <1>;
344 compatible = "brcm,nsp-lcpll0";
345 reg = <0x3f100 0x14>;
346 clocks = <&osc>;
347 clock-output-names = "lcpll0", "pcie_phy", "sdio",
348 "ddr_phy";
349 };
350
351 genpll: genpll@3f140 {
352 #clock-cells = <1>;
353 compatible = "brcm,nsp-genpll";
354 reg = <0x3f140 0x24>;
355 clocks = <&osc>;
356 clock-output-names = "genpll", "phy", "ethernetclk",
357 "usbclk", "iprocfast", "sata1",
358 "sata2";
359 };
360
361 pinctrl: pinctrl@3f1c0 {
362 compatible = "brcm,nsp-pinmux";
363 reg = <0x3f1c0 0x04>,
364 <0x30028 0x04>,
365 <0x3f408 0x04>;
366 };
367
368 sata_phy: sata_phy@40100 {
369 compatible = "brcm,iproc-nsp-sata-phy";
370 reg = <0x40100 0x340>;
371 reg-names = "phy";
372 #address-cells = <1>;
373 #size-cells = <0>;
374
375 sata_phy0: sata-phy@0 {
376 reg = <0>;
377 #phy-cells = <0>;
378 status = "disabled";
379 };
380
381 sata_phy1: sata-phy@1 {
382 reg = <1>;
383 #phy-cells = <0>;
384 status = "disabled";
385 };
386 };
387
388 sata: ahci@41000 {
389 compatible = "brcm,bcm-nsp-ahci";
390 reg-names = "ahci", "top-ctrl";
391 reg = <0x41000 0x1000>, <0x40020 0x1c>;
392 interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
393 #address-cells = <1>;
394 #size-cells = <0>;
395 status = "disabled";
396
397 sata0: sata-port@0 {
398 reg = <0>;
399 phys = <&sata_phy0>;
400 phy-names = "sata-phy";
401 };
402
403 sata1: sata-port@1 {
404 reg = <1>;
405 phys = <&sata_phy1>;
406 phy-names = "sata-phy";
407 };
408 };
409 };
410
411 pcie0: pcie@18012000 {
412 compatible = "brcm,iproc-pcie";
413 reg = <0x18012000 0x1000>;
414
415 #interrupt-cells = <1>;
416 interrupt-map-mask = <0 0 0 0>;
417 interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_NONE>;
418
419 linux,pci-domain = <0>;
420
421 bus-range = <0x00 0xff>;
422
423 #address-cells = <3>;
424 #size-cells = <2>;
425 device_type = "pci";
426
427 /* Note: The HW does not support I/O resources. So,
428 * only the memory resource range is being specified.
429 */
430 ranges = <0x82000000 0 0x08000000 0x08000000 0 0x8000000>;
431
432 status = "disabled";
433
434 msi-parent = <&msi0>;
435 msi0: msi@18012000 {
436 compatible = "brcm,iproc-msi";
437 msi-controller;
438 interrupt-parent = <&gic>;
439 interrupts = <GIC_SPI 127 IRQ_TYPE_NONE>,
440 <GIC_SPI 128 IRQ_TYPE_NONE>,
441 <GIC_SPI 129 IRQ_TYPE_NONE>,
442 <GIC_SPI 130 IRQ_TYPE_NONE>;
443 brcm,pcie-msi-inten;
444 };
445 };
446
447 pcie1: pcie@18013000 {
448 compatible = "brcm,iproc-pcie";
449 reg = <0x18013000 0x1000>;
450
451 #interrupt-cells = <1>;
452 interrupt-map-mask = <0 0 0 0>;
453 interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_NONE>;
454
455 linux,pci-domain = <1>;
456
457 bus-range = <0x00 0xff>;
458
459 #address-cells = <3>;
460 #size-cells = <2>;
461 device_type = "pci";
462
463 /* Note: The HW does not support I/O resources. So,
464 * only the memory resource range is being specified.
465 */
466 ranges = <0x82000000 0 0x40000000 0x40000000 0 0x8000000>;
467
468 status = "disabled";
469
470 msi-parent = <&msi1>;
471 msi1: msi@18013000 {
472 compatible = "brcm,iproc-msi";
473 msi-controller;
474 interrupt-parent = <&gic>;
475 interrupts = <GIC_SPI 133 IRQ_TYPE_NONE>,
476 <GIC_SPI 134 IRQ_TYPE_NONE>,
477 <GIC_SPI 135 IRQ_TYPE_NONE>,
478 <GIC_SPI 136 IRQ_TYPE_NONE>;
479 brcm,pcie-msi-inten;
480 };
481 };
482
483 pcie2: pcie@18014000 {
484 compatible = "brcm,iproc-pcie";
485 reg = <0x18014000 0x1000>;
486
487 #interrupt-cells = <1>;
488 interrupt-map-mask = <0 0 0 0>;
489 interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_NONE>;
490
491 linux,pci-domain = <2>;
492
493 bus-range = <0x00 0xff>;
494
495 #address-cells = <3>;
496 #size-cells = <2>;
497 device_type = "pci";
498
499 /* Note: The HW does not support I/O resources. So,
500 * only the memory resource range is being specified.
501 */
502 ranges = <0x82000000 0 0x48000000 0x48000000 0 0x8000000>;
503
504 status = "disabled";
505
506 msi-parent = <&msi2>;
507 msi2: msi@18014000 {
508 compatible = "brcm,iproc-msi";
509 msi-controller;
510 interrupt-parent = <&gic>;
511 interrupts = <GIC_SPI 139 IRQ_TYPE_NONE>,
512 <GIC_SPI 140 IRQ_TYPE_NONE>,
513 <GIC_SPI 141 IRQ_TYPE_NONE>,
514 <GIC_SPI 142 IRQ_TYPE_NONE>;
515 brcm,pcie-msi-inten;
516 };
517 };
518};