Loading...
1#
2# USB Gadget support on a system involves
3# (a) a peripheral controller, and
4# (b) the gadget driver using it.
5#
6# NOTE: Gadget support ** DOES NOT ** depend on host-side CONFIG_USB !!
7#
8# - Host systems (like PCs) need CONFIG_USB (with "A" jacks).
9# - Peripherals (like PDAs) need CONFIG_USB_GADGET (with "B" jacks).
10# - Some systems have both kinds of controllers.
11#
12# With help from a special transceiver and a "Mini-AB" jack, systems with
13# both kinds of controller can also support "USB On-the-Go" (CONFIG_USB_OTG).
14#
15
16menuconfig USB_GADGET
17 tristate "USB Gadget Support"
18 select NLS
19 help
20 USB is a master/slave protocol, organized with one master
21 host (such as a PC) controlling up to 127 peripheral devices.
22 The USB hardware is asymmetric, which makes it easier to set up:
23 you can't connect a "to-the-host" connector to a peripheral.
24
25 Linux can run in the host, or in the peripheral. In both cases
26 you need a low level bus controller driver, and some software
27 talking to it. Peripheral controllers are often discrete silicon,
28 or are integrated with the CPU in a microcontroller. The more
29 familiar host side controllers have names like "EHCI", "OHCI",
30 or "UHCI", and are usually integrated into southbridges on PC
31 motherboards.
32
33 Enable this configuration option if you want to run Linux inside
34 a USB peripheral device. Configure one hardware driver for your
35 peripheral/device side bus controller, and a "gadget driver" for
36 your peripheral protocol. (If you use modular gadget drivers,
37 you may configure more than one.)
38
39 If in doubt, say "N" and don't enable these drivers; most people
40 don't have this kind of hardware (except maybe inside Linux PDAs).
41
42 For more information, see <http://www.linux-usb.org/gadget> and
43 the kernel DocBook documentation for this API.
44
45if USB_GADGET
46
47config USB_GADGET_DEBUG
48 bool "Debugging messages (DEVELOPMENT)"
49 depends on DEBUG_KERNEL
50 help
51 Many controller and gadget drivers will print some debugging
52 messages if you use this option to ask for those messages.
53
54 Avoid enabling these messages, even if you're actively
55 debugging such a driver. Many drivers will emit so many
56 messages that the driver timings are affected, which will
57 either create new failure modes or remove the one you're
58 trying to track down. Never enable these messages for a
59 production build.
60
61config USB_GADGET_VERBOSE
62 bool "Verbose debugging Messages (DEVELOPMENT)"
63 depends on USB_GADGET_DEBUG
64 help
65 Many controller and gadget drivers will print verbose debugging
66 messages if you use this option to ask for those messages.
67
68 Avoid enabling these messages, even if you're actively
69 debugging such a driver. Many drivers will emit so many
70 messages that the driver timings are affected, which will
71 either create new failure modes or remove the one you're
72 trying to track down. Never enable these messages for a
73 production build.
74
75config USB_GADGET_DEBUG_FILES
76 bool "Debugging information files (DEVELOPMENT)"
77 depends on PROC_FS
78 help
79 Some of the drivers in the "gadget" framework can expose
80 debugging information in files such as /proc/driver/udc
81 (for a peripheral controller). The information in these
82 files may help when you're troubleshooting or bringing up a
83 driver on a new board. Enable these files by choosing "Y"
84 here. If in doubt, or to conserve kernel memory, say "N".
85
86config USB_GADGET_DEBUG_FS
87 bool "Debugging information files in debugfs (DEVELOPMENT)"
88 depends on DEBUG_FS
89 help
90 Some of the drivers in the "gadget" framework can expose
91 debugging information in files under /sys/kernel/debug/.
92 The information in these files may help when you're
93 troubleshooting or bringing up a driver on a new board.
94 Enable these files by choosing "Y" here. If in doubt, or
95 to conserve kernel memory, say "N".
96
97config USB_GADGET_VBUS_DRAW
98 int "Maximum VBUS Power usage (2-500 mA)"
99 range 2 500
100 default 2
101 help
102 Some devices need to draw power from USB when they are
103 configured, perhaps to operate circuitry or to recharge
104 batteries. This is in addition to any local power supply,
105 such as an AC adapter or batteries.
106
107 Enter the maximum power your device draws through USB, in
108 milliAmperes. The permitted range of values is 2 - 500 mA;
109 0 mA would be legal, but can make some hosts misbehave.
110
111 This value will be used except for system-specific gadget
112 drivers that have more specific information.
113
114config USB_GADGET_STORAGE_NUM_BUFFERS
115 int "Number of storage pipeline buffers"
116 range 2 32
117 default 2
118 help
119 Usually 2 buffers are enough to establish a good buffering
120 pipeline. The number may be increased in order to compensate
121 for a bursty VFS behaviour. For instance there may be CPU wake up
122 latencies that makes the VFS to appear bursty in a system with
123 an CPU on-demand governor. Especially if DMA is doing IO to
124 offload the CPU. In this case the CPU will go into power
125 save often and spin up occasionally to move data within VFS.
126 If selecting USB_GADGET_DEBUG_FILES this value may be set by
127 a module parameter as well.
128 If unsure, say 2.
129
130config U_SERIAL_CONSOLE
131 bool "Serial gadget console support"
132 depends on USB_G_SERIAL
133 help
134 It supports the serial gadget can be used as a console.
135
136source "drivers/usb/gadget/udc/Kconfig"
137
138#
139# USB Gadget Drivers
140#
141
142# composite based drivers
143config USB_LIBCOMPOSITE
144 tristate
145 select CONFIGFS_FS
146 depends on USB_GADGET
147
148config USB_F_ACM
149 tristate
150
151config USB_F_SS_LB
152 tristate
153
154config USB_U_SERIAL
155 tristate
156
157config USB_U_ETHER
158 tristate
159
160config USB_F_SERIAL
161 tristate
162
163config USB_F_OBEX
164 tristate
165
166config USB_F_NCM
167 tristate
168
169config USB_F_ECM
170 tristate
171
172config USB_F_PHONET
173 tristate
174
175config USB_F_EEM
176 tristate
177
178config USB_F_SUBSET
179 tristate
180
181config USB_F_RNDIS
182 tristate
183
184config USB_F_MASS_STORAGE
185 tristate
186
187config USB_F_FS
188 tristate
189
190config USB_F_UAC1
191 tristate
192
193config USB_F_UAC2
194 tristate
195
196config USB_F_UVC
197 tristate
198
199config USB_F_MIDI
200 tristate
201
202config USB_F_HID
203 tristate
204
205config USB_F_PRINTER
206 tristate
207
208config USB_F_TCM
209 tristate
210
211choice
212 tristate "USB Gadget Drivers"
213 default USB_ETH
214 help
215 A Linux "Gadget Driver" talks to the USB Peripheral Controller
216 driver through the abstract "gadget" API. Some other operating
217 systems call these "client" drivers, of which "class drivers"
218 are a subset (implementing a USB device class specification).
219 A gadget driver implements one or more USB functions using
220 the peripheral hardware.
221
222 Gadget drivers are hardware-neutral, or "platform independent",
223 except that they sometimes must understand quirks or limitations
224 of the particular controllers they work with. For example, when
225 a controller doesn't support alternate configurations or provide
226 enough of the right types of endpoints, the gadget driver might
227 not be able work with that controller, or might need to implement
228 a less common variant of a device class protocol.
229
230# this first set of drivers all depend on bulk-capable hardware.
231
232config USB_CONFIGFS
233 tristate "USB functions configurable through configfs"
234 select USB_LIBCOMPOSITE
235 help
236 A Linux USB "gadget" can be set up through configfs.
237 If this is the case, the USB functions (which from the host's
238 perspective are seen as interfaces) and configurations are
239 specified simply by creating appropriate directories in configfs.
240 Associating functions with configurations is done by creating
241 appropriate symbolic links.
242 For more information see Documentation/usb/gadget_configfs.txt.
243
244config USB_CONFIGFS_SERIAL
245 bool "Generic serial bulk in/out"
246 depends on USB_CONFIGFS
247 depends on TTY
248 select USB_U_SERIAL
249 select USB_F_SERIAL
250 help
251 The function talks to the Linux-USB generic serial driver.
252
253config USB_CONFIGFS_ACM
254 bool "Abstract Control Model (CDC ACM)"
255 depends on USB_CONFIGFS
256 depends on TTY
257 select USB_U_SERIAL
258 select USB_F_ACM
259 help
260 ACM serial link. This function can be used to interoperate with
261 MS-Windows hosts or with the Linux-USB "cdc-acm" driver.
262
263config USB_CONFIGFS_OBEX
264 bool "Object Exchange Model (CDC OBEX)"
265 depends on USB_CONFIGFS
266 depends on TTY
267 select USB_U_SERIAL
268 select USB_F_OBEX
269 help
270 You will need a user space OBEX server talking to /dev/ttyGS*,
271 since the kernel itself doesn't implement the OBEX protocol.
272
273config USB_CONFIGFS_NCM
274 bool "Network Control Model (CDC NCM)"
275 depends on USB_CONFIGFS
276 depends on NET
277 select USB_U_ETHER
278 select USB_F_NCM
279 help
280 NCM is an advanced protocol for Ethernet encapsulation, allows
281 grouping of several ethernet frames into one USB transfer and
282 different alignment possibilities.
283
284config USB_CONFIGFS_ECM
285 bool "Ethernet Control Model (CDC ECM)"
286 depends on USB_CONFIGFS
287 depends on NET
288 select USB_U_ETHER
289 select USB_F_ECM
290 help
291 The "Communication Device Class" (CDC) Ethernet Control Model.
292 That protocol is often avoided with pure Ethernet adapters, in
293 favor of simpler vendor-specific hardware, but is widely
294 supported by firmware for smart network devices.
295
296config USB_CONFIGFS_ECM_SUBSET
297 bool "Ethernet Control Model (CDC ECM) subset"
298 depends on USB_CONFIGFS
299 depends on NET
300 select USB_U_ETHER
301 select USB_F_SUBSET
302 help
303 On hardware that can't implement the full protocol,
304 a simple CDC subset is used, placing fewer demands on USB.
305
306config USB_CONFIGFS_RNDIS
307 bool "RNDIS"
308 depends on USB_CONFIGFS
309 depends on NET
310 select USB_U_ETHER
311 select USB_F_RNDIS
312 help
313 Microsoft Windows XP bundles the "Remote NDIS" (RNDIS) protocol,
314 and Microsoft provides redistributable binary RNDIS drivers for
315 older versions of Windows.
316
317 To make MS-Windows work with this, use Documentation/usb/linux.inf
318 as the "driver info file". For versions of MS-Windows older than
319 XP, you'll need to download drivers from Microsoft's website; a URL
320 is given in comments found in that info file.
321
322config USB_CONFIGFS_EEM
323 bool "Ethernet Emulation Model (EEM)"
324 depends on USB_CONFIGFS
325 depends on NET
326 select USB_U_ETHER
327 select USB_F_EEM
328 help
329 CDC EEM is a newer USB standard that is somewhat simpler than CDC ECM
330 and therefore can be supported by more hardware. Technically ECM and
331 EEM are designed for different applications. The ECM model extends
332 the network interface to the target (e.g. a USB cable modem), and the
333 EEM model is for mobile devices to communicate with hosts using
334 ethernet over USB. For Linux gadgets, however, the interface with
335 the host is the same (a usbX device), so the differences are minimal.
336
337config USB_CONFIGFS_PHONET
338 bool "Phonet protocol"
339 depends on USB_CONFIGFS
340 depends on NET
341 depends on PHONET
342 select USB_U_ETHER
343 select USB_F_PHONET
344 help
345 The Phonet protocol implementation for USB device.
346
347config USB_CONFIGFS_MASS_STORAGE
348 bool "Mass storage"
349 depends on USB_CONFIGFS
350 depends on BLOCK
351 select USB_F_MASS_STORAGE
352 help
353 The Mass Storage Gadget acts as a USB Mass Storage disk drive.
354 As its storage repository it can use a regular file or a block
355 device (in much the same way as the "loop" device driver),
356 specified as a module parameter or sysfs option.
357
358config USB_CONFIGFS_F_LB_SS
359 bool "Loopback and sourcesink function (for testing)"
360 depends on USB_CONFIGFS
361 select USB_F_SS_LB
362 help
363 Loopback function loops back a configurable number of transfers.
364 Sourcesink function either sinks and sources bulk data.
365 It also implements control requests, for "chapter 9" conformance.
366 Make this be the first driver you try using on top of any new
367 USB peripheral controller driver. Then you can use host-side
368 test software, like the "usbtest" driver, to put your hardware
369 and its driver through a basic set of functional tests.
370
371config USB_CONFIGFS_F_FS
372 bool "Function filesystem (FunctionFS)"
373 depends on USB_CONFIGFS
374 select USB_F_FS
375 help
376 The Function Filesystem (FunctionFS) lets one create USB
377 composite functions in user space in the same way GadgetFS
378 lets one create USB gadgets in user space. This allows creation
379 of composite gadgets such that some of the functions are
380 implemented in kernel space (for instance Ethernet, serial or
381 mass storage) and other are implemented in user space.
382
383config USB_CONFIGFS_F_UAC1
384 bool "Audio Class 1.0"
385 depends on USB_CONFIGFS
386 depends on SND
387 select USB_LIBCOMPOSITE
388 select SND_PCM
389 select USB_F_UAC1
390 help
391 This Audio function implements 1 AudioControl interface,
392 1 AudioStreaming Interface each for USB-OUT and USB-IN.
393 This driver requires a real Audio codec to be present
394 on the device.
395
396config USB_CONFIGFS_F_UAC2
397 bool "Audio Class 2.0"
398 depends on USB_CONFIGFS
399 depends on SND
400 select USB_LIBCOMPOSITE
401 select SND_PCM
402 select USB_F_UAC2
403 help
404 This Audio function is compatible with USB Audio Class
405 specification 2.0. It implements 1 AudioControl interface,
406 1 AudioStreaming Interface each for USB-OUT and USB-IN.
407 This driver doesn't expect any real Audio codec to be present
408 on the device - the audio streams are simply sinked to and
409 sourced from a virtual ALSA sound card created. The user-space
410 application may choose to do whatever it wants with the data
411 received from the USB Host and choose to provide whatever it
412 wants as audio data to the USB Host.
413
414config USB_CONFIGFS_F_MIDI
415 bool "MIDI function"
416 depends on USB_CONFIGFS
417 depends on SND
418 select USB_LIBCOMPOSITE
419 select SND_RAWMIDI
420 select USB_F_MIDI
421 help
422 The MIDI Function acts as a USB Audio device, with one MIDI
423 input and one MIDI output. These MIDI jacks appear as
424 a sound "card" in the ALSA sound system. Other MIDI
425 connections can then be made on the gadget system, using
426 ALSA's aconnect utility etc.
427
428config USB_CONFIGFS_F_HID
429 bool "HID function"
430 depends on USB_CONFIGFS
431 select USB_F_HID
432 help
433 The HID function driver provides generic emulation of USB
434 Human Interface Devices (HID).
435
436 For more information, see Documentation/usb/gadget_hid.txt.
437
438config USB_CONFIGFS_F_UVC
439 bool "USB Webcam function"
440 depends on USB_CONFIGFS
441 depends on VIDEO_DEV
442 select VIDEOBUF2_VMALLOC
443 select USB_F_UVC
444 help
445 The Webcam function acts as a composite USB Audio and Video Class
446 device. It provides a userspace API to process UVC control requests
447 and stream video data to the host.
448
449config USB_CONFIGFS_F_PRINTER
450 bool "Printer function"
451 select USB_F_PRINTER
452 depends on USB_CONFIGFS
453 help
454 The Printer function channels data between the USB host and a
455 userspace program driving the print engine. The user space
456 program reads and writes the device file /dev/g_printer<X> to
457 receive or send printer data. It can use ioctl calls to
458 the device file to get or set printer status.
459
460 For more information, see Documentation/usb/gadget_printer.txt
461 which includes sample code for accessing the device file.
462
463config USB_CONFIGFS_F_TCM
464 bool "USB Gadget Target Fabric"
465 depends on TARGET_CORE
466 depends on USB_CONFIGFS
467 select USB_LIBCOMPOSITE
468 select USB_F_TCM
469 help
470 This fabric is a USB gadget component. Two USB protocols are
471 supported that is BBB or BOT (Bulk Only Transport) and UAS
472 (USB Attached SCSI). BOT is advertised on alternative
473 interface 0 (primary) and UAS is on alternative interface 1.
474 Both protocols can work on USB2.0 and USB3.0.
475 UAS utilizes the USB 3.0 feature called streams support.
476
477source "drivers/usb/gadget/legacy/Kconfig"
478
479endchoice
480
481endif # USB_GADGET
1# SPDX-License-Identifier: GPL-2.0
2#
3# USB Gadget support on a system involves
4# (a) a peripheral controller, and
5# (b) the gadget driver using it.
6#
7# NOTE: Gadget support ** DOES NOT ** depend on host-side CONFIG_USB !!
8#
9# - Host systems (like PCs) need CONFIG_USB (with "A" jacks).
10# - Peripherals (like PDAs) need CONFIG_USB_GADGET (with "B" jacks).
11# - Some systems have both kinds of controllers.
12#
13# With help from a special transceiver and a "Mini-AB" jack, systems with
14# both kinds of controller can also support "USB On-the-Go" (CONFIG_USB_OTG).
15#
16
17menuconfig USB_GADGET
18 tristate "USB Gadget Support"
19 select USB_COMMON
20 select NLS
21 help
22 USB is a host/device protocol, organized with one host (such as a
23 PC) controlling up to 127 peripheral devices.
24 The USB hardware is asymmetric, which makes it easier to set up:
25 you can't connect a "to-the-host" connector to a peripheral.
26
27 Linux can run in the host, or in the peripheral. In both cases
28 you need a low level bus controller driver, and some software
29 talking to it. Peripheral controllers are often discrete silicon,
30 or are integrated with the CPU in a microcontroller. The more
31 familiar host side controllers have names like "EHCI", "OHCI",
32 or "UHCI", and are usually integrated into southbridges on PC
33 motherboards.
34
35 Enable this configuration option if you want to run Linux inside
36 a USB peripheral device. Configure one hardware driver for your
37 peripheral/device side bus controller, and a "gadget driver" for
38 your peripheral protocol. (If you use modular gadget drivers,
39 you may configure more than one.)
40
41 If in doubt, say "N" and don't enable these drivers; most people
42 don't have this kind of hardware (except maybe inside Linux PDAs).
43
44 For more information, see <http://www.linux-usb.org/gadget> and
45 the kernel documentation for this API.
46
47if USB_GADGET
48
49config USB_GADGET_DEBUG
50 bool "Debugging messages (DEVELOPMENT)"
51 depends on DEBUG_KERNEL
52 help
53 Many controller and gadget drivers will print some debugging
54 messages if you use this option to ask for those messages.
55
56 Avoid enabling these messages, even if you're actively
57 debugging such a driver. Many drivers will emit so many
58 messages that the driver timings are affected, which will
59 either create new failure modes or remove the one you're
60 trying to track down. Never enable these messages for a
61 production build.
62
63config USB_GADGET_VERBOSE
64 bool "Verbose debugging Messages (DEVELOPMENT)"
65 depends on USB_GADGET_DEBUG
66 help
67 Many controller and gadget drivers will print verbose debugging
68 messages if you use this option to ask for those messages.
69
70 Avoid enabling these messages, even if you're actively
71 debugging such a driver. Many drivers will emit so many
72 messages that the driver timings are affected, which will
73 either create new failure modes or remove the one you're
74 trying to track down. Never enable these messages for a
75 production build.
76
77config USB_GADGET_DEBUG_FILES
78 bool "Debugging information files (DEVELOPMENT)"
79 depends on PROC_FS
80 help
81 Some of the drivers in the "gadget" framework can expose
82 debugging information in files such as /proc/driver/udc
83 (for a peripheral controller). The information in these
84 files may help when you're troubleshooting or bringing up a
85 driver on a new board. Enable these files by choosing "Y"
86 here. If in doubt, or to conserve kernel memory, say "N".
87
88config USB_GADGET_DEBUG_FS
89 bool "Debugging information files in debugfs (DEVELOPMENT)"
90 depends on DEBUG_FS
91 help
92 Some of the drivers in the "gadget" framework can expose
93 debugging information in files under /sys/kernel/debug/.
94 The information in these files may help when you're
95 troubleshooting or bringing up a driver on a new board.
96 Enable these files by choosing "Y" here. If in doubt, or
97 to conserve kernel memory, say "N".
98
99config USB_GADGET_VBUS_DRAW
100 int "Maximum VBUS Power usage (2-500 mA)"
101 range 2 500
102 default 2
103 help
104 Some devices need to draw power from USB when they are
105 configured, perhaps to operate circuitry or to recharge
106 batteries. This is in addition to any local power supply,
107 such as an AC adapter or batteries.
108
109 Enter the maximum power your device draws through USB, in
110 milliAmperes. The permitted range of values is 2 - 500 mA;
111 0 mA would be legal, but can make some hosts misbehave.
112
113 This value will be used except for system-specific gadget
114 drivers that have more specific information.
115
116config USB_GADGET_STORAGE_NUM_BUFFERS
117 int "Number of storage pipeline buffers"
118 range 2 256
119 default 2
120 help
121 Usually 2 buffers are enough to establish a good buffering
122 pipeline. The number may be increased in order to compensate
123 for a bursty VFS behaviour. For instance there may be CPU wake up
124 latencies that makes the VFS to appear bursty in a system with
125 an CPU on-demand governor. Especially if DMA is doing IO to
126 offload the CPU. In this case the CPU will go into power
127 save often and spin up occasionally to move data within VFS.
128 If selecting USB_GADGET_DEBUG_FILES this value may be set by
129 a module parameter as well.
130 If unsure, say 2.
131
132config U_SERIAL_CONSOLE
133 bool "Serial gadget console support"
134 depends on USB_U_SERIAL
135 help
136 It supports the serial gadget can be used as a console.
137
138source "drivers/usb/gadget/udc/Kconfig"
139
140#
141# USB Gadget Drivers
142#
143
144# composite based drivers
145config USB_LIBCOMPOSITE
146 tristate
147 select CONFIGFS_FS
148 depends on USB_GADGET
149
150config USB_F_ACM
151 tristate
152
153config USB_F_SS_LB
154 tristate
155
156config USB_U_SERIAL
157 tristate
158
159config USB_U_ETHER
160 tristate
161
162config USB_U_AUDIO
163 tristate
164
165config USB_F_SERIAL
166 tristate
167
168config USB_F_OBEX
169 tristate
170
171config USB_F_NCM
172 tristate
173
174config USB_F_ECM
175 tristate
176
177config USB_F_PHONET
178 tristate
179
180config USB_F_EEM
181 tristate
182
183config USB_F_SUBSET
184 tristate
185
186config USB_F_RNDIS
187 tristate
188
189config USB_F_MASS_STORAGE
190 tristate
191
192config USB_F_FS
193 select DMA_SHARED_BUFFER
194 tristate
195
196config USB_F_UAC1
197 tristate
198
199config USB_F_UAC1_LEGACY
200 tristate
201
202config USB_F_UAC2
203 tristate
204
205config USB_F_UVC
206 tristate
207 select UVC_COMMON
208
209config USB_F_MIDI
210 tristate
211
212config USB_F_MIDI2
213 tristate
214
215config USB_F_HID
216 tristate
217
218config USB_F_PRINTER
219 tristate
220
221config USB_F_TCM
222 tristate
223
224# this first set of drivers all depend on bulk-capable hardware.
225
226config USB_CONFIGFS
227 tristate "USB Gadget functions configurable through configfs"
228 select USB_LIBCOMPOSITE
229 help
230 A Linux USB "gadget" can be set up through configfs.
231 If this is the case, the USB functions (which from the host's
232 perspective are seen as interfaces) and configurations are
233 specified simply by creating appropriate directories in configfs.
234 Associating functions with configurations is done by creating
235 appropriate symbolic links.
236 For more information see Documentation/usb/gadget_configfs.rst.
237
238config USB_CONFIGFS_SERIAL
239 bool "Generic serial bulk in/out"
240 depends on USB_CONFIGFS
241 depends on TTY
242 select USB_U_SERIAL
243 select USB_F_SERIAL
244 help
245 The function talks to the Linux-USB generic serial driver.
246
247config USB_CONFIGFS_ACM
248 bool "Abstract Control Model (CDC ACM)"
249 depends on USB_CONFIGFS
250 depends on TTY
251 select USB_U_SERIAL
252 select USB_F_ACM
253 help
254 ACM serial link. This function can be used to interoperate with
255 MS-Windows hosts or with the Linux-USB "cdc-acm" driver.
256
257config USB_CONFIGFS_OBEX
258 bool "Object Exchange Model (CDC OBEX)"
259 depends on USB_CONFIGFS
260 depends on TTY
261 select USB_U_SERIAL
262 select USB_F_OBEX
263 help
264 You will need a user space OBEX server talking to /dev/ttyGS*,
265 since the kernel itself doesn't implement the OBEX protocol.
266
267config USB_CONFIGFS_NCM
268 bool "Network Control Model (CDC NCM)"
269 depends on USB_CONFIGFS
270 depends on NET
271 select USB_U_ETHER
272 select USB_F_NCM
273 select CRC32
274 help
275 NCM is an advanced protocol for Ethernet encapsulation, allows
276 grouping of several ethernet frames into one USB transfer and
277 different alignment possibilities.
278
279config USB_CONFIGFS_ECM
280 bool "Ethernet Control Model (CDC ECM)"
281 depends on USB_CONFIGFS
282 depends on NET
283 select USB_U_ETHER
284 select USB_F_ECM
285 help
286 The "Communication Device Class" (CDC) Ethernet Control Model.
287 That protocol is often avoided with pure Ethernet adapters, in
288 favor of simpler vendor-specific hardware, but is widely
289 supported by firmware for smart network devices.
290
291config USB_CONFIGFS_ECM_SUBSET
292 bool "Ethernet Control Model (CDC ECM) subset"
293 depends on USB_CONFIGFS
294 depends on NET
295 select USB_U_ETHER
296 select USB_F_SUBSET
297 help
298 On hardware that can't implement the full protocol,
299 a simple CDC subset is used, placing fewer demands on USB.
300
301config USB_CONFIGFS_RNDIS
302 bool "RNDIS"
303 depends on USB_CONFIGFS
304 depends on NET
305 select USB_U_ETHER
306 select USB_F_RNDIS
307 help
308 Microsoft Windows XP bundles the "Remote NDIS" (RNDIS) protocol,
309 and Microsoft provides redistributable binary RNDIS drivers for
310 older versions of Windows.
311
312 To make MS-Windows work with this, use Documentation/usb/linux.inf
313 as the "driver info file". For versions of MS-Windows older than
314 XP, you'll need to download drivers from Microsoft's website; a URL
315 is given in comments found in that info file.
316
317config USB_CONFIGFS_EEM
318 bool "Ethernet Emulation Model (EEM)"
319 depends on USB_CONFIGFS
320 depends on NET
321 select USB_U_ETHER
322 select USB_F_EEM
323 select CRC32
324 help
325 CDC EEM is a newer USB standard that is somewhat simpler than CDC ECM
326 and therefore can be supported by more hardware. Technically ECM and
327 EEM are designed for different applications. The ECM model extends
328 the network interface to the target (e.g. a USB cable modem), and the
329 EEM model is for mobile devices to communicate with hosts using
330 ethernet over USB. For Linux gadgets, however, the interface with
331 the host is the same (a usbX device), so the differences are minimal.
332
333config USB_CONFIGFS_PHONET
334 bool "Phonet protocol"
335 depends on USB_CONFIGFS
336 depends on NET
337 depends on PHONET
338 select USB_U_ETHER
339 select USB_F_PHONET
340 help
341 The Phonet protocol implementation for USB device.
342
343config USB_CONFIGFS_MASS_STORAGE
344 bool "Mass storage"
345 depends on USB_CONFIGFS
346 depends on BLOCK
347 select USB_F_MASS_STORAGE
348 help
349 The Mass Storage Gadget acts as a USB Mass Storage disk drive.
350 As its storage repository it can use a regular file or a block
351 device (in much the same way as the "loop" device driver),
352 specified as a module parameter or sysfs option.
353
354config USB_CONFIGFS_F_LB_SS
355 bool "Loopback and sourcesink function (for testing)"
356 depends on USB_CONFIGFS
357 select USB_F_SS_LB
358 help
359 Loopback function loops back a configurable number of transfers.
360 Sourcesink function either sinks and sources bulk data.
361 It also implements control requests, for "chapter 9" conformance.
362 Make this be the first driver you try using on top of any new
363 USB peripheral controller driver. Then you can use host-side
364 test software, like the "usbtest" driver, to put your hardware
365 and its driver through a basic set of functional tests.
366
367config USB_CONFIGFS_F_FS
368 bool "Function filesystem (FunctionFS)"
369 depends on USB_CONFIGFS
370 select USB_F_FS
371 help
372 The Function Filesystem (FunctionFS) lets one create USB
373 composite functions in user space in the same way GadgetFS
374 lets one create USB gadgets in user space. This allows creation
375 of composite gadgets such that some of the functions are
376 implemented in kernel space (for instance Ethernet, serial or
377 mass storage) and other are implemented in user space.
378
379config USB_CONFIGFS_F_UAC1
380 bool "Audio Class 1.0"
381 depends on USB_CONFIGFS
382 depends on SND
383 select USB_LIBCOMPOSITE
384 select SND_PCM
385 select USB_U_AUDIO
386 select USB_F_UAC1
387 help
388 This Audio function implements 1 AudioControl interface,
389 1 AudioStreaming Interface each for USB-OUT and USB-IN.
390 This driver doesn't expect any real Audio codec to be present
391 on the device - the audio streams are simply sinked to and
392 sourced from a virtual ALSA sound card created. The user-space
393 application may choose to do whatever it wants with the data
394 received from the USB Host and choose to provide whatever it
395 wants as audio data to the USB Host.
396
397config USB_CONFIGFS_F_UAC1_LEGACY
398 bool "Audio Class 1.0 (legacy implementation)"
399 depends on USB_CONFIGFS
400 depends on SND
401 select USB_LIBCOMPOSITE
402 select SND_PCM
403 select USB_F_UAC1_LEGACY
404 help
405 This Audio function implements 1 AudioControl interface,
406 1 AudioStreaming Interface each for USB-OUT and USB-IN.
407 This is a legacy driver and requires a real Audio codec
408 to be present on the device.
409
410config USB_CONFIGFS_F_UAC2
411 bool "Audio Class 2.0"
412 depends on USB_CONFIGFS
413 depends on SND
414 select USB_LIBCOMPOSITE
415 select SND_PCM
416 select USB_U_AUDIO
417 select USB_F_UAC2
418 help
419 This Audio function is compatible with USB Audio Class
420 specification 2.0. It implements 1 AudioControl interface,
421 1 AudioStreaming Interface each for USB-OUT and USB-IN.
422 This driver doesn't expect any real Audio codec to be present
423 on the device - the audio streams are simply sinked to and
424 sourced from a virtual ALSA sound card created. The user-space
425 application may choose to do whatever it wants with the data
426 received from the USB Host and choose to provide whatever it
427 wants as audio data to the USB Host.
428
429config USB_CONFIGFS_F_MIDI
430 bool "MIDI function"
431 depends on USB_CONFIGFS
432 depends on SND
433 select USB_LIBCOMPOSITE
434 select SND_RAWMIDI
435 select USB_F_MIDI
436 help
437 The MIDI Function acts as a USB Audio device, with one MIDI
438 input and one MIDI output. These MIDI jacks appear as
439 a sound "card" in the ALSA sound system. Other MIDI
440 connections can then be made on the gadget system, using
441 ALSA's aconnect utility etc.
442
443config USB_CONFIGFS_F_MIDI2
444 bool "MIDI 2.0 function"
445 depends on USB_CONFIGFS
446 depends on SND
447 select USB_LIBCOMPOSITE
448 select SND_UMP
449 select SND_UMP_LEGACY_RAWMIDI
450 select USB_F_MIDI2
451 help
452 The MIDI 2.0 function driver provides the generic emulated
453 USB MIDI 2.0 interface, looped back to ALSA UMP rawmidi
454 device on the gadget host. It supports UMP 1.1 spec and
455 responds UMP Stream messages for UMP Endpoint and Function
456 Block information / configuration.
457
458config USB_CONFIGFS_F_HID
459 bool "HID function"
460 depends on USB_CONFIGFS
461 select USB_F_HID
462 help
463 The HID function driver provides generic emulation of USB
464 Human Interface Devices (HID).
465
466 For more information, see Documentation/usb/gadget_hid.rst.
467
468config USB_CONFIGFS_F_UVC
469 bool "USB Webcam function"
470 depends on USB_CONFIGFS
471 depends on VIDEO_DEV
472 depends on VIDEO_DEV
473 select VIDEOBUF2_DMA_SG
474 select VIDEOBUF2_VMALLOC
475 select USB_F_UVC
476 help
477 The Webcam function acts as a composite USB Audio and Video Class
478 device. It provides a userspace API to process UVC control requests
479 and stream video data to the host.
480
481config USB_CONFIGFS_F_PRINTER
482 bool "Printer function"
483 select USB_F_PRINTER
484 depends on USB_CONFIGFS
485 help
486 The Printer function channels data between the USB host and a
487 userspace program driving the print engine. The user space
488 program reads and writes the device file /dev/g_printer<X> to
489 receive or send printer data. It can use ioctl calls to
490 the device file to get or set printer status.
491
492 For more information, see Documentation/usb/gadget_printer.rst
493 which includes sample code for accessing the device file.
494
495config USB_CONFIGFS_F_TCM
496 bool "USB Gadget Target Fabric"
497 depends on TARGET_CORE
498 depends on USB_CONFIGFS
499 select USB_LIBCOMPOSITE
500 select USB_F_TCM
501 help
502 This fabric is a USB gadget component. Two USB protocols are
503 supported that is BBB or BOT (Bulk Only Transport) and UAS
504 (USB Attached SCSI). BOT is advertised on alternative
505 interface 0 (primary) and UAS is on alternative interface 1.
506 Both protocols can work on USB2.0 and USB3.0.
507 UAS utilizes the USB 3.0 feature called streams support.
508
509source "drivers/usb/gadget/legacy/Kconfig"
510
511endif # USB_GADGET