Loading...
1/*
2 * This program is free software; you can redistribute it and/or modify
3 * it under the terms of the GNU General Public License as published by
4 * the Free Software Foundation; either version 2 of the License, or
5 * (at your option) any later version.
6 *
7 * This program is distributed in the hope that it will be useful,
8 * but WITHOUT ANY WARRANTY; without even the implied warranty of
9 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
10 * GNU General Public License for more details.
11 *
12 * You should have received a copy of the GNU General Public License
13 * along with this program; if not, write to the Free Software
14 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
15 *
16 * Clean ups from Moschip version and a few ioctl implementations by:
17 * Paul B Schroeder <pschroeder "at" uplogix "dot" com>
18 *
19 * Originally based on drivers/usb/serial/io_edgeport.c which is:
20 * Copyright (C) 2000 Inside Out Networks, All rights reserved.
21 * Copyright (C) 2001-2002 Greg Kroah-Hartman <greg@kroah.com>
22 *
23 */
24
25#include <linux/kernel.h>
26#include <linux/errno.h>
27#include <linux/slab.h>
28#include <linux/tty.h>
29#include <linux/tty_driver.h>
30#include <linux/tty_flip.h>
31#include <linux/module.h>
32#include <linux/serial.h>
33#include <linux/usb.h>
34#include <linux/usb/serial.h>
35#include <linux/uaccess.h>
36
37#define DRIVER_DESC "Moschip 7840/7820 USB Serial Driver"
38
39/*
40 * 16C50 UART register defines
41 */
42
43#define LCR_BITS_5 0x00 /* 5 bits/char */
44#define LCR_BITS_6 0x01 /* 6 bits/char */
45#define LCR_BITS_7 0x02 /* 7 bits/char */
46#define LCR_BITS_8 0x03 /* 8 bits/char */
47#define LCR_BITS_MASK 0x03 /* Mask for bits/char field */
48
49#define LCR_STOP_1 0x00 /* 1 stop bit */
50#define LCR_STOP_1_5 0x04 /* 1.5 stop bits (if 5 bits/char) */
51#define LCR_STOP_2 0x04 /* 2 stop bits (if 6-8 bits/char) */
52#define LCR_STOP_MASK 0x04 /* Mask for stop bits field */
53
54#define LCR_PAR_NONE 0x00 /* No parity */
55#define LCR_PAR_ODD 0x08 /* Odd parity */
56#define LCR_PAR_EVEN 0x18 /* Even parity */
57#define LCR_PAR_MARK 0x28 /* Force parity bit to 1 */
58#define LCR_PAR_SPACE 0x38 /* Force parity bit to 0 */
59#define LCR_PAR_MASK 0x38 /* Mask for parity field */
60
61#define LCR_SET_BREAK 0x40 /* Set Break condition */
62#define LCR_DL_ENABLE 0x80 /* Enable access to divisor latch */
63
64#define MCR_DTR 0x01 /* Assert DTR */
65#define MCR_RTS 0x02 /* Assert RTS */
66#define MCR_OUT1 0x04 /* Loopback only: Sets state of RI */
67#define MCR_MASTER_IE 0x08 /* Enable interrupt outputs */
68#define MCR_LOOPBACK 0x10 /* Set internal (digital) loopback mode */
69#define MCR_XON_ANY 0x20 /* Enable any char to exit XOFF mode */
70
71#define MOS7840_MSR_CTS 0x10 /* Current state of CTS */
72#define MOS7840_MSR_DSR 0x20 /* Current state of DSR */
73#define MOS7840_MSR_RI 0x40 /* Current state of RI */
74#define MOS7840_MSR_CD 0x80 /* Current state of CD */
75
76/*
77 * Defines used for sending commands to port
78 */
79
80#define MOS_WDR_TIMEOUT 5000 /* default urb timeout */
81
82#define MOS_PORT1 0x0200
83#define MOS_PORT2 0x0300
84#define MOS_VENREG 0x0000
85#define MOS_MAX_PORT 0x02
86#define MOS_WRITE 0x0E
87#define MOS_READ 0x0D
88
89/* Requests */
90#define MCS_RD_RTYPE 0xC0
91#define MCS_WR_RTYPE 0x40
92#define MCS_RDREQ 0x0D
93#define MCS_WRREQ 0x0E
94#define MCS_CTRL_TIMEOUT 500
95#define VENDOR_READ_LENGTH (0x01)
96
97#define MAX_NAME_LEN 64
98
99#define ZLP_REG1 0x3A /* Zero_Flag_Reg1 58 */
100#define ZLP_REG5 0x3E /* Zero_Flag_Reg5 62 */
101
102/* For higher baud Rates use TIOCEXBAUD */
103#define TIOCEXBAUD 0x5462
104
105/* vendor id and device id defines */
106
107/* The native mos7840/7820 component */
108#define USB_VENDOR_ID_MOSCHIP 0x9710
109#define MOSCHIP_DEVICE_ID_7840 0x7840
110#define MOSCHIP_DEVICE_ID_7820 0x7820
111#define MOSCHIP_DEVICE_ID_7810 0x7810
112/* The native component can have its vendor/device id's overridden
113 * in vendor-specific implementations. Such devices can be handled
114 * by making a change here, in id_table.
115 */
116#define USB_VENDOR_ID_BANDB 0x0856
117#define BANDB_DEVICE_ID_USO9ML2_2 0xAC22
118#define BANDB_DEVICE_ID_USO9ML2_2P 0xBC00
119#define BANDB_DEVICE_ID_USO9ML2_4 0xAC24
120#define BANDB_DEVICE_ID_USO9ML2_4P 0xBC01
121#define BANDB_DEVICE_ID_US9ML2_2 0xAC29
122#define BANDB_DEVICE_ID_US9ML2_4 0xAC30
123#define BANDB_DEVICE_ID_USPTL4_2 0xAC31
124#define BANDB_DEVICE_ID_USPTL4_4 0xAC32
125#define BANDB_DEVICE_ID_USOPTL4_2 0xAC42
126#define BANDB_DEVICE_ID_USOPTL4_2P 0xBC02
127#define BANDB_DEVICE_ID_USOPTL4_4 0xAC44
128#define BANDB_DEVICE_ID_USOPTL4_4P 0xBC03
129#define BANDB_DEVICE_ID_USOPTL2_4 0xAC24
130
131/* This driver also supports
132 * ATEN UC2324 device using Moschip MCS7840
133 * ATEN UC2322 device using Moschip MCS7820
134 */
135#define USB_VENDOR_ID_ATENINTL 0x0557
136#define ATENINTL_DEVICE_ID_UC2324 0x2011
137#define ATENINTL_DEVICE_ID_UC2322 0x7820
138
139/* Interrupt Routine Defines */
140
141#define SERIAL_IIR_RLS 0x06
142#define SERIAL_IIR_MS 0x00
143
144/*
145 * Emulation of the bit mask on the LINE STATUS REGISTER.
146 */
147#define SERIAL_LSR_DR 0x0001
148#define SERIAL_LSR_OE 0x0002
149#define SERIAL_LSR_PE 0x0004
150#define SERIAL_LSR_FE 0x0008
151#define SERIAL_LSR_BI 0x0010
152
153#define MOS_MSR_DELTA_CTS 0x10
154#define MOS_MSR_DELTA_DSR 0x20
155#define MOS_MSR_DELTA_RI 0x40
156#define MOS_MSR_DELTA_CD 0x80
157
158/* Serial Port register Address */
159#define INTERRUPT_ENABLE_REGISTER ((__u16)(0x01))
160#define FIFO_CONTROL_REGISTER ((__u16)(0x02))
161#define LINE_CONTROL_REGISTER ((__u16)(0x03))
162#define MODEM_CONTROL_REGISTER ((__u16)(0x04))
163#define LINE_STATUS_REGISTER ((__u16)(0x05))
164#define MODEM_STATUS_REGISTER ((__u16)(0x06))
165#define SCRATCH_PAD_REGISTER ((__u16)(0x07))
166#define DIVISOR_LATCH_LSB ((__u16)(0x00))
167#define DIVISOR_LATCH_MSB ((__u16)(0x01))
168
169#define CLK_MULTI_REGISTER ((__u16)(0x02))
170#define CLK_START_VALUE_REGISTER ((__u16)(0x03))
171#define GPIO_REGISTER ((__u16)(0x07))
172
173#define SERIAL_LCR_DLAB ((__u16)(0x0080))
174
175/*
176 * URB POOL related defines
177 */
178#define NUM_URBS 16 /* URB Count */
179#define URB_TRANSFER_BUFFER_SIZE 32 /* URB Size */
180
181/* LED on/off milliseconds*/
182#define LED_ON_MS 500
183#define LED_OFF_MS 500
184
185enum mos7840_flag {
186 MOS7840_FLAG_CTRL_BUSY,
187 MOS7840_FLAG_LED_BUSY,
188};
189
190static const struct usb_device_id id_table[] = {
191 {USB_DEVICE(USB_VENDOR_ID_MOSCHIP, MOSCHIP_DEVICE_ID_7840)},
192 {USB_DEVICE(USB_VENDOR_ID_MOSCHIP, MOSCHIP_DEVICE_ID_7820)},
193 {USB_DEVICE(USB_VENDOR_ID_MOSCHIP, MOSCHIP_DEVICE_ID_7810)},
194 {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_2)},
195 {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_2P)},
196 {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_4)},
197 {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_4P)},
198 {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_US9ML2_2)},
199 {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_US9ML2_4)},
200 {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USPTL4_2)},
201 {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USPTL4_4)},
202 {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2)},
203 {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2P)},
204 {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4)},
205 {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4P)},
206 {USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL2_4)},
207 {USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2324)},
208 {USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_UC2322)},
209 {} /* terminating entry */
210};
211MODULE_DEVICE_TABLE(usb, id_table);
212
213/* This structure holds all of the local port information */
214
215struct moschip_port {
216 int port_num; /*Actual port number in the device(1,2,etc) */
217 struct urb *write_urb; /* write URB for this port */
218 struct urb *read_urb; /* read URB for this port */
219 __u8 shadowLCR; /* last LCR value received */
220 __u8 shadowMCR; /* last MCR value received */
221 char open;
222 char open_ports;
223 struct usb_serial_port *port; /* loop back to the owner of this object */
224
225 /* Offsets */
226 __u8 SpRegOffset;
227 __u8 ControlRegOffset;
228 __u8 DcrRegOffset;
229 /* for processing control URBS in interrupt context */
230 struct urb *control_urb;
231 struct usb_ctrlrequest *dr;
232 char *ctrl_buf;
233 int MsrLsr;
234
235 spinlock_t pool_lock;
236 struct urb *write_urb_pool[NUM_URBS];
237 char busy[NUM_URBS];
238 bool read_urb_busy;
239
240 /* For device(s) with LED indicator */
241 bool has_led;
242 struct timer_list led_timer1; /* Timer for LED on */
243 struct timer_list led_timer2; /* Timer for LED off */
244 struct urb *led_urb;
245 struct usb_ctrlrequest *led_dr;
246
247 unsigned long flags;
248};
249
250/*
251 * mos7840_set_reg_sync
252 * To set the Control register by calling usb_fill_control_urb function
253 * by passing usb_sndctrlpipe function as parameter.
254 */
255
256static int mos7840_set_reg_sync(struct usb_serial_port *port, __u16 reg,
257 __u16 val)
258{
259 struct usb_device *dev = port->serial->dev;
260 val = val & 0x00ff;
261 dev_dbg(&port->dev, "mos7840_set_reg_sync offset is %x, value %x\n", reg, val);
262
263 return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), MCS_WRREQ,
264 MCS_WR_RTYPE, val, reg, NULL, 0,
265 MOS_WDR_TIMEOUT);
266}
267
268/*
269 * mos7840_get_reg_sync
270 * To set the Uart register by calling usb_fill_control_urb function by
271 * passing usb_rcvctrlpipe function as parameter.
272 */
273
274static int mos7840_get_reg_sync(struct usb_serial_port *port, __u16 reg,
275 __u16 *val)
276{
277 struct usb_device *dev = port->serial->dev;
278 int ret = 0;
279 u8 *buf;
280
281 buf = kmalloc(VENDOR_READ_LENGTH, GFP_KERNEL);
282 if (!buf)
283 return -ENOMEM;
284
285 ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), MCS_RDREQ,
286 MCS_RD_RTYPE, 0, reg, buf, VENDOR_READ_LENGTH,
287 MOS_WDR_TIMEOUT);
288 *val = buf[0];
289 dev_dbg(&port->dev, "%s offset is %x, return val %x\n", __func__, reg, *val);
290
291 kfree(buf);
292 return ret;
293}
294
295/*
296 * mos7840_set_uart_reg
297 * To set the Uart register by calling usb_fill_control_urb function by
298 * passing usb_sndctrlpipe function as parameter.
299 */
300
301static int mos7840_set_uart_reg(struct usb_serial_port *port, __u16 reg,
302 __u16 val)
303{
304
305 struct usb_device *dev = port->serial->dev;
306 val = val & 0x00ff;
307 /* For the UART control registers, the application number need
308 to be Or'ed */
309 if (port->serial->num_ports == 4) {
310 val |= ((__u16)port->port_number + 1) << 8;
311 } else {
312 if (port->port_number == 0) {
313 val |= ((__u16)port->port_number + 1) << 8;
314 } else {
315 val |= ((__u16)port->port_number + 2) << 8;
316 }
317 }
318 dev_dbg(&port->dev, "%s application number is %x\n", __func__, val);
319 return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), MCS_WRREQ,
320 MCS_WR_RTYPE, val, reg, NULL, 0,
321 MOS_WDR_TIMEOUT);
322
323}
324
325/*
326 * mos7840_get_uart_reg
327 * To set the Control register by calling usb_fill_control_urb function
328 * by passing usb_rcvctrlpipe function as parameter.
329 */
330static int mos7840_get_uart_reg(struct usb_serial_port *port, __u16 reg,
331 __u16 *val)
332{
333 struct usb_device *dev = port->serial->dev;
334 int ret = 0;
335 __u16 Wval;
336 u8 *buf;
337
338 buf = kmalloc(VENDOR_READ_LENGTH, GFP_KERNEL);
339 if (!buf)
340 return -ENOMEM;
341
342 /* Wval is same as application number */
343 if (port->serial->num_ports == 4) {
344 Wval = ((__u16)port->port_number + 1) << 8;
345 } else {
346 if (port->port_number == 0) {
347 Wval = ((__u16)port->port_number + 1) << 8;
348 } else {
349 Wval = ((__u16)port->port_number + 2) << 8;
350 }
351 }
352 dev_dbg(&port->dev, "%s application number is %x\n", __func__, Wval);
353 ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), MCS_RDREQ,
354 MCS_RD_RTYPE, Wval, reg, buf, VENDOR_READ_LENGTH,
355 MOS_WDR_TIMEOUT);
356 *val = buf[0];
357
358 kfree(buf);
359 return ret;
360}
361
362static void mos7840_dump_serial_port(struct usb_serial_port *port,
363 struct moschip_port *mos7840_port)
364{
365
366 dev_dbg(&port->dev, "SpRegOffset is %2x\n", mos7840_port->SpRegOffset);
367 dev_dbg(&port->dev, "ControlRegOffset is %2x\n", mos7840_port->ControlRegOffset);
368 dev_dbg(&port->dev, "DCRRegOffset is %2x\n", mos7840_port->DcrRegOffset);
369
370}
371
372/************************************************************************/
373/************************************************************************/
374/* I N T E R F A C E F U N C T I O N S */
375/* I N T E R F A C E F U N C T I O N S */
376/************************************************************************/
377/************************************************************************/
378
379static inline void mos7840_set_port_private(struct usb_serial_port *port,
380 struct moschip_port *data)
381{
382 usb_set_serial_port_data(port, (void *)data);
383}
384
385static inline struct moschip_port *mos7840_get_port_private(struct
386 usb_serial_port
387 *port)
388{
389 return (struct moschip_port *)usb_get_serial_port_data(port);
390}
391
392static void mos7840_handle_new_msr(struct moschip_port *port, __u8 new_msr)
393{
394 struct moschip_port *mos7840_port;
395 struct async_icount *icount;
396 mos7840_port = port;
397 if (new_msr &
398 (MOS_MSR_DELTA_CTS | MOS_MSR_DELTA_DSR | MOS_MSR_DELTA_RI |
399 MOS_MSR_DELTA_CD)) {
400 icount = &mos7840_port->port->icount;
401
402 /* update input line counters */
403 if (new_msr & MOS_MSR_DELTA_CTS)
404 icount->cts++;
405 if (new_msr & MOS_MSR_DELTA_DSR)
406 icount->dsr++;
407 if (new_msr & MOS_MSR_DELTA_CD)
408 icount->dcd++;
409 if (new_msr & MOS_MSR_DELTA_RI)
410 icount->rng++;
411
412 wake_up_interruptible(&port->port->port.delta_msr_wait);
413 }
414}
415
416static void mos7840_handle_new_lsr(struct moschip_port *port, __u8 new_lsr)
417{
418 struct async_icount *icount;
419
420 if (new_lsr & SERIAL_LSR_BI) {
421 /*
422 * Parity and Framing errors only count if they
423 * occur exclusive of a break being
424 * received.
425 */
426 new_lsr &= (__u8) (SERIAL_LSR_OE | SERIAL_LSR_BI);
427 }
428
429 /* update input line counters */
430 icount = &port->port->icount;
431 if (new_lsr & SERIAL_LSR_BI)
432 icount->brk++;
433 if (new_lsr & SERIAL_LSR_OE)
434 icount->overrun++;
435 if (new_lsr & SERIAL_LSR_PE)
436 icount->parity++;
437 if (new_lsr & SERIAL_LSR_FE)
438 icount->frame++;
439}
440
441/************************************************************************/
442/************************************************************************/
443/* U S B C A L L B A C K F U N C T I O N S */
444/* U S B C A L L B A C K F U N C T I O N S */
445/************************************************************************/
446/************************************************************************/
447
448static void mos7840_control_callback(struct urb *urb)
449{
450 unsigned char *data;
451 struct moschip_port *mos7840_port;
452 struct device *dev = &urb->dev->dev;
453 __u8 regval = 0x0;
454 int status = urb->status;
455
456 mos7840_port = urb->context;
457
458 switch (status) {
459 case 0:
460 /* success */
461 break;
462 case -ECONNRESET:
463 case -ENOENT:
464 case -ESHUTDOWN:
465 /* this urb is terminated, clean up */
466 dev_dbg(dev, "%s - urb shutting down with status: %d\n", __func__, status);
467 goto out;
468 default:
469 dev_dbg(dev, "%s - nonzero urb status received: %d\n", __func__, status);
470 goto out;
471 }
472
473 dev_dbg(dev, "%s urb buffer size is %d\n", __func__, urb->actual_length);
474 dev_dbg(dev, "%s mos7840_port->MsrLsr is %d port %d\n", __func__,
475 mos7840_port->MsrLsr, mos7840_port->port_num);
476 data = urb->transfer_buffer;
477 regval = (__u8) data[0];
478 dev_dbg(dev, "%s data is %x\n", __func__, regval);
479 if (mos7840_port->MsrLsr == 0)
480 mos7840_handle_new_msr(mos7840_port, regval);
481 else if (mos7840_port->MsrLsr == 1)
482 mos7840_handle_new_lsr(mos7840_port, regval);
483out:
484 clear_bit_unlock(MOS7840_FLAG_CTRL_BUSY, &mos7840_port->flags);
485}
486
487static int mos7840_get_reg(struct moschip_port *mcs, __u16 Wval, __u16 reg,
488 __u16 *val)
489{
490 struct usb_device *dev = mcs->port->serial->dev;
491 struct usb_ctrlrequest *dr = mcs->dr;
492 unsigned char *buffer = mcs->ctrl_buf;
493 int ret;
494
495 if (test_and_set_bit_lock(MOS7840_FLAG_CTRL_BUSY, &mcs->flags))
496 return -EBUSY;
497
498 dr->bRequestType = MCS_RD_RTYPE;
499 dr->bRequest = MCS_RDREQ;
500 dr->wValue = cpu_to_le16(Wval); /* 0 */
501 dr->wIndex = cpu_to_le16(reg);
502 dr->wLength = cpu_to_le16(2);
503
504 usb_fill_control_urb(mcs->control_urb, dev, usb_rcvctrlpipe(dev, 0),
505 (unsigned char *)dr, buffer, 2,
506 mos7840_control_callback, mcs);
507 mcs->control_urb->transfer_buffer_length = 2;
508 ret = usb_submit_urb(mcs->control_urb, GFP_ATOMIC);
509 if (ret)
510 clear_bit_unlock(MOS7840_FLAG_CTRL_BUSY, &mcs->flags);
511
512 return ret;
513}
514
515static void mos7840_set_led_callback(struct urb *urb)
516{
517 switch (urb->status) {
518 case 0:
519 /* Success */
520 break;
521 case -ECONNRESET:
522 case -ENOENT:
523 case -ESHUTDOWN:
524 /* This urb is terminated, clean up */
525 dev_dbg(&urb->dev->dev, "%s - urb shutting down: %d\n",
526 __func__, urb->status);
527 break;
528 default:
529 dev_dbg(&urb->dev->dev, "%s - nonzero urb status: %d\n",
530 __func__, urb->status);
531 }
532}
533
534static void mos7840_set_led_async(struct moschip_port *mcs, __u16 wval,
535 __u16 reg)
536{
537 struct usb_device *dev = mcs->port->serial->dev;
538 struct usb_ctrlrequest *dr = mcs->led_dr;
539
540 dr->bRequestType = MCS_WR_RTYPE;
541 dr->bRequest = MCS_WRREQ;
542 dr->wValue = cpu_to_le16(wval);
543 dr->wIndex = cpu_to_le16(reg);
544 dr->wLength = cpu_to_le16(0);
545
546 usb_fill_control_urb(mcs->led_urb, dev, usb_sndctrlpipe(dev, 0),
547 (unsigned char *)dr, NULL, 0, mos7840_set_led_callback, NULL);
548
549 usb_submit_urb(mcs->led_urb, GFP_ATOMIC);
550}
551
552static void mos7840_set_led_sync(struct usb_serial_port *port, __u16 reg,
553 __u16 val)
554{
555 struct usb_device *dev = port->serial->dev;
556
557 usb_control_msg(dev, usb_sndctrlpipe(dev, 0), MCS_WRREQ, MCS_WR_RTYPE,
558 val, reg, NULL, 0, MOS_WDR_TIMEOUT);
559}
560
561static void mos7840_led_off(unsigned long arg)
562{
563 struct moschip_port *mcs = (struct moschip_port *) arg;
564
565 /* Turn off LED */
566 mos7840_set_led_async(mcs, 0x0300, MODEM_CONTROL_REGISTER);
567 mod_timer(&mcs->led_timer2,
568 jiffies + msecs_to_jiffies(LED_OFF_MS));
569}
570
571static void mos7840_led_flag_off(unsigned long arg)
572{
573 struct moschip_port *mcs = (struct moschip_port *) arg;
574
575 clear_bit_unlock(MOS7840_FLAG_LED_BUSY, &mcs->flags);
576}
577
578static void mos7840_led_activity(struct usb_serial_port *port)
579{
580 struct moschip_port *mos7840_port = usb_get_serial_port_data(port);
581
582 if (test_and_set_bit_lock(MOS7840_FLAG_LED_BUSY, &mos7840_port->flags))
583 return;
584
585 mos7840_set_led_async(mos7840_port, 0x0301, MODEM_CONTROL_REGISTER);
586 mod_timer(&mos7840_port->led_timer1,
587 jiffies + msecs_to_jiffies(LED_ON_MS));
588}
589
590/*****************************************************************************
591 * mos7840_interrupt_callback
592 * this is the callback function for when we have received data on the
593 * interrupt endpoint.
594 *****************************************************************************/
595
596static void mos7840_interrupt_callback(struct urb *urb)
597{
598 int result;
599 int length;
600 struct moschip_port *mos7840_port;
601 struct usb_serial *serial;
602 __u16 Data;
603 unsigned char *data;
604 __u8 sp[5], st;
605 int i, rv = 0;
606 __u16 wval, wreg = 0;
607 int status = urb->status;
608
609 switch (status) {
610 case 0:
611 /* success */
612 break;
613 case -ECONNRESET:
614 case -ENOENT:
615 case -ESHUTDOWN:
616 /* this urb is terminated, clean up */
617 dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n",
618 __func__, status);
619 return;
620 default:
621 dev_dbg(&urb->dev->dev, "%s - nonzero urb status received: %d\n",
622 __func__, status);
623 goto exit;
624 }
625
626 length = urb->actual_length;
627 data = urb->transfer_buffer;
628
629 serial = urb->context;
630
631 /* Moschip get 5 bytes
632 * Byte 1 IIR Port 1 (port.number is 0)
633 * Byte 2 IIR Port 2 (port.number is 1)
634 * Byte 3 IIR Port 3 (port.number is 2)
635 * Byte 4 IIR Port 4 (port.number is 3)
636 * Byte 5 FIFO status for both */
637
638 if (length > 5) {
639 dev_dbg(&urb->dev->dev, "%s", "Wrong data !!!\n");
640 return;
641 }
642
643 sp[0] = (__u8) data[0];
644 sp[1] = (__u8) data[1];
645 sp[2] = (__u8) data[2];
646 sp[3] = (__u8) data[3];
647 st = (__u8) data[4];
648
649 for (i = 0; i < serial->num_ports; i++) {
650 mos7840_port = mos7840_get_port_private(serial->port[i]);
651 wval = ((__u16)serial->port[i]->port_number + 1) << 8;
652 if (mos7840_port->open) {
653 if (sp[i] & 0x01) {
654 dev_dbg(&urb->dev->dev, "SP%d No Interrupt !!!\n", i);
655 } else {
656 switch (sp[i] & 0x0f) {
657 case SERIAL_IIR_RLS:
658 dev_dbg(&urb->dev->dev, "Serial Port %d: Receiver status error or \n", i);
659 dev_dbg(&urb->dev->dev, "address bit detected in 9-bit mode\n");
660 mos7840_port->MsrLsr = 1;
661 wreg = LINE_STATUS_REGISTER;
662 break;
663 case SERIAL_IIR_MS:
664 dev_dbg(&urb->dev->dev, "Serial Port %d: Modem status change\n", i);
665 mos7840_port->MsrLsr = 0;
666 wreg = MODEM_STATUS_REGISTER;
667 break;
668 }
669 rv = mos7840_get_reg(mos7840_port, wval, wreg, &Data);
670 }
671 }
672 }
673 if (!(rv < 0))
674 /* the completion handler for the control urb will resubmit */
675 return;
676exit:
677 result = usb_submit_urb(urb, GFP_ATOMIC);
678 if (result) {
679 dev_err(&urb->dev->dev,
680 "%s - Error %d submitting interrupt urb\n",
681 __func__, result);
682 }
683}
684
685static int mos7840_port_paranoia_check(struct usb_serial_port *port,
686 const char *function)
687{
688 if (!port) {
689 pr_debug("%s - port == NULL\n", function);
690 return -1;
691 }
692 if (!port->serial) {
693 pr_debug("%s - port->serial == NULL\n", function);
694 return -1;
695 }
696
697 return 0;
698}
699
700/* Inline functions to check the sanity of a pointer that is passed to us */
701static int mos7840_serial_paranoia_check(struct usb_serial *serial,
702 const char *function)
703{
704 if (!serial) {
705 pr_debug("%s - serial == NULL\n", function);
706 return -1;
707 }
708 if (!serial->type) {
709 pr_debug("%s - serial->type == NULL!\n", function);
710 return -1;
711 }
712
713 return 0;
714}
715
716static struct usb_serial *mos7840_get_usb_serial(struct usb_serial_port *port,
717 const char *function)
718{
719 /* if no port was specified, or it fails a paranoia check */
720 if (!port ||
721 mos7840_port_paranoia_check(port, function) ||
722 mos7840_serial_paranoia_check(port->serial, function)) {
723 /* then say that we don't have a valid usb_serial thing,
724 * which will end up genrating -ENODEV return values */
725 return NULL;
726 }
727
728 return port->serial;
729}
730
731/*****************************************************************************
732 * mos7840_bulk_in_callback
733 * this is the callback function for when we have received data on the
734 * bulk in endpoint.
735 *****************************************************************************/
736
737static void mos7840_bulk_in_callback(struct urb *urb)
738{
739 int retval;
740 unsigned char *data;
741 struct usb_serial *serial;
742 struct usb_serial_port *port;
743 struct moschip_port *mos7840_port;
744 int status = urb->status;
745
746 mos7840_port = urb->context;
747 if (!mos7840_port)
748 return;
749
750 if (status) {
751 dev_dbg(&urb->dev->dev, "nonzero read bulk status received: %d\n", status);
752 mos7840_port->read_urb_busy = false;
753 return;
754 }
755
756 port = mos7840_port->port;
757 if (mos7840_port_paranoia_check(port, __func__)) {
758 mos7840_port->read_urb_busy = false;
759 return;
760 }
761
762 serial = mos7840_get_usb_serial(port, __func__);
763 if (!serial) {
764 mos7840_port->read_urb_busy = false;
765 return;
766 }
767
768 data = urb->transfer_buffer;
769 usb_serial_debug_data(&port->dev, __func__, urb->actual_length, data);
770
771 if (urb->actual_length) {
772 struct tty_port *tport = &mos7840_port->port->port;
773 tty_insert_flip_string(tport, data, urb->actual_length);
774 tty_flip_buffer_push(tport);
775 port->icount.rx += urb->actual_length;
776 dev_dbg(&port->dev, "icount.rx is %d:\n", port->icount.rx);
777 }
778
779 if (!mos7840_port->read_urb) {
780 dev_dbg(&port->dev, "%s", "URB KILLED !!!\n");
781 mos7840_port->read_urb_busy = false;
782 return;
783 }
784
785 if (mos7840_port->has_led)
786 mos7840_led_activity(port);
787
788 mos7840_port->read_urb_busy = true;
789 retval = usb_submit_urb(mos7840_port->read_urb, GFP_ATOMIC);
790
791 if (retval) {
792 dev_dbg(&port->dev, "usb_submit_urb(read bulk) failed, retval = %d\n", retval);
793 mos7840_port->read_urb_busy = false;
794 }
795}
796
797/*****************************************************************************
798 * mos7840_bulk_out_data_callback
799 * this is the callback function for when we have finished sending
800 * serial data on the bulk out endpoint.
801 *****************************************************************************/
802
803static void mos7840_bulk_out_data_callback(struct urb *urb)
804{
805 struct moschip_port *mos7840_port;
806 struct usb_serial_port *port;
807 int status = urb->status;
808 int i;
809
810 mos7840_port = urb->context;
811 port = mos7840_port->port;
812 spin_lock(&mos7840_port->pool_lock);
813 for (i = 0; i < NUM_URBS; i++) {
814 if (urb == mos7840_port->write_urb_pool[i]) {
815 mos7840_port->busy[i] = 0;
816 break;
817 }
818 }
819 spin_unlock(&mos7840_port->pool_lock);
820
821 if (status) {
822 dev_dbg(&port->dev, "nonzero write bulk status received:%d\n", status);
823 return;
824 }
825
826 if (mos7840_port_paranoia_check(port, __func__))
827 return;
828
829 if (mos7840_port->open)
830 tty_port_tty_wakeup(&port->port);
831
832}
833
834/************************************************************************/
835/* D R I V E R T T Y I N T E R F A C E F U N C T I O N S */
836/************************************************************************/
837
838/*****************************************************************************
839 * mos7840_open
840 * this function is called by the tty driver when a port is opened
841 * If successful, we return 0
842 * Otherwise we return a negative error number.
843 *****************************************************************************/
844
845static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port)
846{
847 int response;
848 int j;
849 struct usb_serial *serial;
850 struct urb *urb;
851 __u16 Data;
852 int status;
853 struct moschip_port *mos7840_port;
854 struct moschip_port *port0;
855
856 if (mos7840_port_paranoia_check(port, __func__))
857 return -ENODEV;
858
859 serial = port->serial;
860
861 if (mos7840_serial_paranoia_check(serial, __func__))
862 return -ENODEV;
863
864 mos7840_port = mos7840_get_port_private(port);
865 port0 = mos7840_get_port_private(serial->port[0]);
866
867 if (mos7840_port == NULL || port0 == NULL)
868 return -ENODEV;
869
870 usb_clear_halt(serial->dev, port->write_urb->pipe);
871 usb_clear_halt(serial->dev, port->read_urb->pipe);
872 port0->open_ports++;
873
874 /* Initialising the write urb pool */
875 for (j = 0; j < NUM_URBS; ++j) {
876 urb = usb_alloc_urb(0, GFP_KERNEL);
877 mos7840_port->write_urb_pool[j] = urb;
878 if (!urb)
879 continue;
880
881 urb->transfer_buffer = kmalloc(URB_TRANSFER_BUFFER_SIZE,
882 GFP_KERNEL);
883 if (!urb->transfer_buffer) {
884 usb_free_urb(urb);
885 mos7840_port->write_urb_pool[j] = NULL;
886 continue;
887 }
888 }
889
890/*****************************************************************************
891 * Initialize MCS7840 -- Write Init values to corresponding Registers
892 *
893 * Register Index
894 * 1 : IER
895 * 2 : FCR
896 * 3 : LCR
897 * 4 : MCR
898 *
899 * 0x08 : SP1/2 Control Reg
900 *****************************************************************************/
901
902 /* NEED to check the following Block */
903
904 Data = 0x0;
905 status = mos7840_get_reg_sync(port, mos7840_port->SpRegOffset, &Data);
906 if (status < 0) {
907 dev_dbg(&port->dev, "Reading Spreg failed\n");
908 goto err;
909 }
910 Data |= 0x80;
911 status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data);
912 if (status < 0) {
913 dev_dbg(&port->dev, "writing Spreg failed\n");
914 goto err;
915 }
916
917 Data &= ~0x80;
918 status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data);
919 if (status < 0) {
920 dev_dbg(&port->dev, "writing Spreg failed\n");
921 goto err;
922 }
923 /* End of block to be checked */
924
925 Data = 0x0;
926 status = mos7840_get_reg_sync(port, mos7840_port->ControlRegOffset,
927 &Data);
928 if (status < 0) {
929 dev_dbg(&port->dev, "Reading Controlreg failed\n");
930 goto err;
931 }
932 Data |= 0x08; /* Driver done bit */
933 Data |= 0x20; /* rx_disable */
934 status = mos7840_set_reg_sync(port,
935 mos7840_port->ControlRegOffset, Data);
936 if (status < 0) {
937 dev_dbg(&port->dev, "writing Controlreg failed\n");
938 goto err;
939 }
940 /* do register settings here */
941 /* Set all regs to the device default values. */
942 /***********************************
943 * First Disable all interrupts.
944 ***********************************/
945 Data = 0x00;
946 status = mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
947 if (status < 0) {
948 dev_dbg(&port->dev, "disabling interrupts failed\n");
949 goto err;
950 }
951 /* Set FIFO_CONTROL_REGISTER to the default value */
952 Data = 0x00;
953 status = mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
954 if (status < 0) {
955 dev_dbg(&port->dev, "Writing FIFO_CONTROL_REGISTER failed\n");
956 goto err;
957 }
958
959 Data = 0xcf;
960 status = mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
961 if (status < 0) {
962 dev_dbg(&port->dev, "Writing FIFO_CONTROL_REGISTER failed\n");
963 goto err;
964 }
965
966 Data = 0x03;
967 status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
968 mos7840_port->shadowLCR = Data;
969
970 Data = 0x0b;
971 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
972 mos7840_port->shadowMCR = Data;
973
974 Data = 0x00;
975 status = mos7840_get_uart_reg(port, LINE_CONTROL_REGISTER, &Data);
976 mos7840_port->shadowLCR = Data;
977
978 Data |= SERIAL_LCR_DLAB; /* data latch enable in LCR 0x80 */
979 status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
980
981 Data = 0x0c;
982 status = mos7840_set_uart_reg(port, DIVISOR_LATCH_LSB, Data);
983
984 Data = 0x0;
985 status = mos7840_set_uart_reg(port, DIVISOR_LATCH_MSB, Data);
986
987 Data = 0x00;
988 status = mos7840_get_uart_reg(port, LINE_CONTROL_REGISTER, &Data);
989
990 Data = Data & ~SERIAL_LCR_DLAB;
991 status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
992 mos7840_port->shadowLCR = Data;
993
994 /* clearing Bulkin and Bulkout Fifo */
995 Data = 0x0;
996 status = mos7840_get_reg_sync(port, mos7840_port->SpRegOffset, &Data);
997
998 Data = Data | 0x0c;
999 status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data);
1000
1001 Data = Data & ~0x0c;
1002 status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data);
1003 /* Finally enable all interrupts */
1004 Data = 0x0c;
1005 status = mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
1006
1007 /* clearing rx_disable */
1008 Data = 0x0;
1009 status = mos7840_get_reg_sync(port, mos7840_port->ControlRegOffset,
1010 &Data);
1011 Data = Data & ~0x20;
1012 status = mos7840_set_reg_sync(port, mos7840_port->ControlRegOffset,
1013 Data);
1014
1015 /* rx_negate */
1016 Data = 0x0;
1017 status = mos7840_get_reg_sync(port, mos7840_port->ControlRegOffset,
1018 &Data);
1019 Data = Data | 0x10;
1020 status = mos7840_set_reg_sync(port, mos7840_port->ControlRegOffset,
1021 Data);
1022
1023 /* Check to see if we've set up our endpoint info yet *
1024 * (can't set it up in mos7840_startup as the structures *
1025 * were not set up at that time.) */
1026 if (port0->open_ports == 1) {
1027 if (serial->port[0]->interrupt_in_buffer == NULL) {
1028 /* set up interrupt urb */
1029 usb_fill_int_urb(serial->port[0]->interrupt_in_urb,
1030 serial->dev,
1031 usb_rcvintpipe(serial->dev,
1032 serial->port[0]->interrupt_in_endpointAddress),
1033 serial->port[0]->interrupt_in_buffer,
1034 serial->port[0]->interrupt_in_urb->
1035 transfer_buffer_length,
1036 mos7840_interrupt_callback,
1037 serial,
1038 serial->port[0]->interrupt_in_urb->interval);
1039
1040 /* start interrupt read for mos7840 *
1041 * will continue as long as mos7840 is connected */
1042
1043 response =
1044 usb_submit_urb(serial->port[0]->interrupt_in_urb,
1045 GFP_KERNEL);
1046 if (response) {
1047 dev_err(&port->dev, "%s - Error %d submitting "
1048 "interrupt urb\n", __func__, response);
1049 }
1050
1051 }
1052
1053 }
1054
1055 /* see if we've set up our endpoint info yet *
1056 * (can't set it up in mos7840_startup as the *
1057 * structures were not set up at that time.) */
1058
1059 dev_dbg(&port->dev, "port number is %d\n", port->port_number);
1060 dev_dbg(&port->dev, "minor number is %d\n", port->minor);
1061 dev_dbg(&port->dev, "Bulkin endpoint is %d\n", port->bulk_in_endpointAddress);
1062 dev_dbg(&port->dev, "BulkOut endpoint is %d\n", port->bulk_out_endpointAddress);
1063 dev_dbg(&port->dev, "Interrupt endpoint is %d\n", port->interrupt_in_endpointAddress);
1064 dev_dbg(&port->dev, "port's number in the device is %d\n", mos7840_port->port_num);
1065 mos7840_port->read_urb = port->read_urb;
1066
1067 /* set up our bulk in urb */
1068 if ((serial->num_ports == 2) && (((__u16)port->port_number % 2) != 0)) {
1069 usb_fill_bulk_urb(mos7840_port->read_urb,
1070 serial->dev,
1071 usb_rcvbulkpipe(serial->dev,
1072 (port->bulk_in_endpointAddress) + 2),
1073 port->bulk_in_buffer,
1074 mos7840_port->read_urb->transfer_buffer_length,
1075 mos7840_bulk_in_callback, mos7840_port);
1076 } else {
1077 usb_fill_bulk_urb(mos7840_port->read_urb,
1078 serial->dev,
1079 usb_rcvbulkpipe(serial->dev,
1080 port->bulk_in_endpointAddress),
1081 port->bulk_in_buffer,
1082 mos7840_port->read_urb->transfer_buffer_length,
1083 mos7840_bulk_in_callback, mos7840_port);
1084 }
1085
1086 dev_dbg(&port->dev, "%s: bulkin endpoint is %d\n", __func__, port->bulk_in_endpointAddress);
1087 mos7840_port->read_urb_busy = true;
1088 response = usb_submit_urb(mos7840_port->read_urb, GFP_KERNEL);
1089 if (response) {
1090 dev_err(&port->dev, "%s - Error %d submitting control urb\n",
1091 __func__, response);
1092 mos7840_port->read_urb_busy = false;
1093 }
1094
1095 /* initialize our port settings */
1096 /* Must set to enable ints! */
1097 mos7840_port->shadowMCR = MCR_MASTER_IE;
1098 /* send a open port command */
1099 mos7840_port->open = 1;
1100 /* mos7840_change_port_settings(mos7840_port,old_termios); */
1101
1102 return 0;
1103err:
1104 for (j = 0; j < NUM_URBS; ++j) {
1105 urb = mos7840_port->write_urb_pool[j];
1106 if (!urb)
1107 continue;
1108 kfree(urb->transfer_buffer);
1109 usb_free_urb(urb);
1110 }
1111 return status;
1112}
1113
1114/*****************************************************************************
1115 * mos7840_chars_in_buffer
1116 * this function is called by the tty driver when it wants to know how many
1117 * bytes of data we currently have outstanding in the port (data that has
1118 * been written, but hasn't made it out the port yet)
1119 * If successful, we return the number of bytes left to be written in the
1120 * system,
1121 * Otherwise we return zero.
1122 *****************************************************************************/
1123
1124static int mos7840_chars_in_buffer(struct tty_struct *tty)
1125{
1126 struct usb_serial_port *port = tty->driver_data;
1127 int i;
1128 int chars = 0;
1129 unsigned long flags;
1130 struct moschip_port *mos7840_port;
1131
1132 if (mos7840_port_paranoia_check(port, __func__))
1133 return 0;
1134
1135 mos7840_port = mos7840_get_port_private(port);
1136 if (mos7840_port == NULL)
1137 return 0;
1138
1139 spin_lock_irqsave(&mos7840_port->pool_lock, flags);
1140 for (i = 0; i < NUM_URBS; ++i) {
1141 if (mos7840_port->busy[i]) {
1142 struct urb *urb = mos7840_port->write_urb_pool[i];
1143 chars += urb->transfer_buffer_length;
1144 }
1145 }
1146 spin_unlock_irqrestore(&mos7840_port->pool_lock, flags);
1147 dev_dbg(&port->dev, "%s - returns %d\n", __func__, chars);
1148 return chars;
1149
1150}
1151
1152/*****************************************************************************
1153 * mos7840_close
1154 * this function is called by the tty driver when a port is closed
1155 *****************************************************************************/
1156
1157static void mos7840_close(struct usb_serial_port *port)
1158{
1159 struct usb_serial *serial;
1160 struct moschip_port *mos7840_port;
1161 struct moschip_port *port0;
1162 int j;
1163 __u16 Data;
1164
1165 if (mos7840_port_paranoia_check(port, __func__))
1166 return;
1167
1168 serial = mos7840_get_usb_serial(port, __func__);
1169 if (!serial)
1170 return;
1171
1172 mos7840_port = mos7840_get_port_private(port);
1173 port0 = mos7840_get_port_private(serial->port[0]);
1174
1175 if (mos7840_port == NULL || port0 == NULL)
1176 return;
1177
1178 for (j = 0; j < NUM_URBS; ++j)
1179 usb_kill_urb(mos7840_port->write_urb_pool[j]);
1180
1181 /* Freeing Write URBs */
1182 for (j = 0; j < NUM_URBS; ++j) {
1183 if (mos7840_port->write_urb_pool[j]) {
1184 kfree(mos7840_port->write_urb_pool[j]->transfer_buffer);
1185 usb_free_urb(mos7840_port->write_urb_pool[j]);
1186 }
1187 }
1188
1189 usb_kill_urb(mos7840_port->write_urb);
1190 usb_kill_urb(mos7840_port->read_urb);
1191 mos7840_port->read_urb_busy = false;
1192
1193 port0->open_ports--;
1194 dev_dbg(&port->dev, "%s in close%d\n", __func__, port0->open_ports);
1195 if (port0->open_ports == 0) {
1196 if (serial->port[0]->interrupt_in_urb) {
1197 dev_dbg(&port->dev, "Shutdown interrupt_in_urb\n");
1198 usb_kill_urb(serial->port[0]->interrupt_in_urb);
1199 }
1200 }
1201
1202 if (mos7840_port->write_urb) {
1203 /* if this urb had a transfer buffer already (old tx) free it */
1204 kfree(mos7840_port->write_urb->transfer_buffer);
1205 usb_free_urb(mos7840_port->write_urb);
1206 }
1207
1208 Data = 0x0;
1209 mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
1210
1211 Data = 0x00;
1212 mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
1213
1214 mos7840_port->open = 0;
1215}
1216
1217/*****************************************************************************
1218 * mos7840_break
1219 * this function sends a break to the port
1220 *****************************************************************************/
1221static void mos7840_break(struct tty_struct *tty, int break_state)
1222{
1223 struct usb_serial_port *port = tty->driver_data;
1224 unsigned char data;
1225 struct usb_serial *serial;
1226 struct moschip_port *mos7840_port;
1227
1228 if (mos7840_port_paranoia_check(port, __func__))
1229 return;
1230
1231 serial = mos7840_get_usb_serial(port, __func__);
1232 if (!serial)
1233 return;
1234
1235 mos7840_port = mos7840_get_port_private(port);
1236
1237 if (mos7840_port == NULL)
1238 return;
1239
1240 if (break_state == -1)
1241 data = mos7840_port->shadowLCR | LCR_SET_BREAK;
1242 else
1243 data = mos7840_port->shadowLCR & ~LCR_SET_BREAK;
1244
1245 /* FIXME: no locking on shadowLCR anywhere in driver */
1246 mos7840_port->shadowLCR = data;
1247 dev_dbg(&port->dev, "%s mos7840_port->shadowLCR is %x\n", __func__, mos7840_port->shadowLCR);
1248 mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER,
1249 mos7840_port->shadowLCR);
1250}
1251
1252/*****************************************************************************
1253 * mos7840_write_room
1254 * this function is called by the tty driver when it wants to know how many
1255 * bytes of data we can accept for a specific port.
1256 * If successful, we return the amount of room that we have for this port
1257 * Otherwise we return a negative error number.
1258 *****************************************************************************/
1259
1260static int mos7840_write_room(struct tty_struct *tty)
1261{
1262 struct usb_serial_port *port = tty->driver_data;
1263 int i;
1264 int room = 0;
1265 unsigned long flags;
1266 struct moschip_port *mos7840_port;
1267
1268 if (mos7840_port_paranoia_check(port, __func__))
1269 return -1;
1270
1271 mos7840_port = mos7840_get_port_private(port);
1272 if (mos7840_port == NULL)
1273 return -1;
1274
1275 spin_lock_irqsave(&mos7840_port->pool_lock, flags);
1276 for (i = 0; i < NUM_URBS; ++i) {
1277 if (!mos7840_port->busy[i])
1278 room += URB_TRANSFER_BUFFER_SIZE;
1279 }
1280 spin_unlock_irqrestore(&mos7840_port->pool_lock, flags);
1281
1282 room = (room == 0) ? 0 : room - URB_TRANSFER_BUFFER_SIZE + 1;
1283 dev_dbg(&mos7840_port->port->dev, "%s - returns %d\n", __func__, room);
1284 return room;
1285
1286}
1287
1288/*****************************************************************************
1289 * mos7840_write
1290 * this function is called by the tty driver when data should be written to
1291 * the port.
1292 * If successful, we return the number of bytes written, otherwise we
1293 * return a negative error number.
1294 *****************************************************************************/
1295
1296static int mos7840_write(struct tty_struct *tty, struct usb_serial_port *port,
1297 const unsigned char *data, int count)
1298{
1299 int status;
1300 int i;
1301 int bytes_sent = 0;
1302 int transfer_size;
1303 unsigned long flags;
1304
1305 struct moschip_port *mos7840_port;
1306 struct usb_serial *serial;
1307 struct urb *urb;
1308 /* __u16 Data; */
1309 const unsigned char *current_position = data;
1310 unsigned char *data1;
1311
1312 if (mos7840_port_paranoia_check(port, __func__))
1313 return -1;
1314
1315 serial = port->serial;
1316 if (mos7840_serial_paranoia_check(serial, __func__))
1317 return -1;
1318
1319 mos7840_port = mos7840_get_port_private(port);
1320 if (mos7840_port == NULL)
1321 return -1;
1322
1323 /* try to find a free urb in the list */
1324 urb = NULL;
1325
1326 spin_lock_irqsave(&mos7840_port->pool_lock, flags);
1327 for (i = 0; i < NUM_URBS; ++i) {
1328 if (!mos7840_port->busy[i]) {
1329 mos7840_port->busy[i] = 1;
1330 urb = mos7840_port->write_urb_pool[i];
1331 dev_dbg(&port->dev, "URB:%d\n", i);
1332 break;
1333 }
1334 }
1335 spin_unlock_irqrestore(&mos7840_port->pool_lock, flags);
1336
1337 if (urb == NULL) {
1338 dev_dbg(&port->dev, "%s - no more free urbs\n", __func__);
1339 goto exit;
1340 }
1341
1342 if (urb->transfer_buffer == NULL) {
1343 urb->transfer_buffer =
1344 kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL);
1345 if (!urb->transfer_buffer)
1346 goto exit;
1347 }
1348 transfer_size = min(count, URB_TRANSFER_BUFFER_SIZE);
1349
1350 memcpy(urb->transfer_buffer, current_position, transfer_size);
1351
1352 /* fill urb with data and submit */
1353 if ((serial->num_ports == 2) && (((__u16)port->port_number % 2) != 0)) {
1354 usb_fill_bulk_urb(urb,
1355 serial->dev,
1356 usb_sndbulkpipe(serial->dev,
1357 (port->bulk_out_endpointAddress) + 2),
1358 urb->transfer_buffer,
1359 transfer_size,
1360 mos7840_bulk_out_data_callback, mos7840_port);
1361 } else {
1362 usb_fill_bulk_urb(urb,
1363 serial->dev,
1364 usb_sndbulkpipe(serial->dev,
1365 port->bulk_out_endpointAddress),
1366 urb->transfer_buffer,
1367 transfer_size,
1368 mos7840_bulk_out_data_callback, mos7840_port);
1369 }
1370
1371 data1 = urb->transfer_buffer;
1372 dev_dbg(&port->dev, "bulkout endpoint is %d\n", port->bulk_out_endpointAddress);
1373
1374 if (mos7840_port->has_led)
1375 mos7840_led_activity(port);
1376
1377 /* send it down the pipe */
1378 status = usb_submit_urb(urb, GFP_ATOMIC);
1379
1380 if (status) {
1381 mos7840_port->busy[i] = 0;
1382 dev_err_console(port, "%s - usb_submit_urb(write bulk) failed "
1383 "with status = %d\n", __func__, status);
1384 bytes_sent = status;
1385 goto exit;
1386 }
1387 bytes_sent = transfer_size;
1388 port->icount.tx += transfer_size;
1389 dev_dbg(&port->dev, "icount.tx is %d:\n", port->icount.tx);
1390exit:
1391 return bytes_sent;
1392
1393}
1394
1395/*****************************************************************************
1396 * mos7840_throttle
1397 * this function is called by the tty driver when it wants to stop the data
1398 * being read from the port.
1399 *****************************************************************************/
1400
1401static void mos7840_throttle(struct tty_struct *tty)
1402{
1403 struct usb_serial_port *port = tty->driver_data;
1404 struct moschip_port *mos7840_port;
1405 int status;
1406
1407 if (mos7840_port_paranoia_check(port, __func__))
1408 return;
1409
1410 mos7840_port = mos7840_get_port_private(port);
1411
1412 if (mos7840_port == NULL)
1413 return;
1414
1415 if (!mos7840_port->open) {
1416 dev_dbg(&port->dev, "%s", "port not opened\n");
1417 return;
1418 }
1419
1420 /* if we are implementing XON/XOFF, send the stop character */
1421 if (I_IXOFF(tty)) {
1422 unsigned char stop_char = STOP_CHAR(tty);
1423 status = mos7840_write(tty, port, &stop_char, 1);
1424 if (status <= 0)
1425 return;
1426 }
1427 /* if we are implementing RTS/CTS, toggle that line */
1428 if (C_CRTSCTS(tty)) {
1429 mos7840_port->shadowMCR &= ~MCR_RTS;
1430 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
1431 mos7840_port->shadowMCR);
1432 if (status < 0)
1433 return;
1434 }
1435}
1436
1437/*****************************************************************************
1438 * mos7840_unthrottle
1439 * this function is called by the tty driver when it wants to resume
1440 * the data being read from the port (called after mos7840_throttle is
1441 * called)
1442 *****************************************************************************/
1443static void mos7840_unthrottle(struct tty_struct *tty)
1444{
1445 struct usb_serial_port *port = tty->driver_data;
1446 int status;
1447 struct moschip_port *mos7840_port = mos7840_get_port_private(port);
1448
1449 if (mos7840_port_paranoia_check(port, __func__))
1450 return;
1451
1452 if (mos7840_port == NULL)
1453 return;
1454
1455 if (!mos7840_port->open) {
1456 dev_dbg(&port->dev, "%s - port not opened\n", __func__);
1457 return;
1458 }
1459
1460 /* if we are implementing XON/XOFF, send the start character */
1461 if (I_IXOFF(tty)) {
1462 unsigned char start_char = START_CHAR(tty);
1463 status = mos7840_write(tty, port, &start_char, 1);
1464 if (status <= 0)
1465 return;
1466 }
1467
1468 /* if we are implementing RTS/CTS, toggle that line */
1469 if (C_CRTSCTS(tty)) {
1470 mos7840_port->shadowMCR |= MCR_RTS;
1471 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
1472 mos7840_port->shadowMCR);
1473 if (status < 0)
1474 return;
1475 }
1476}
1477
1478static int mos7840_tiocmget(struct tty_struct *tty)
1479{
1480 struct usb_serial_port *port = tty->driver_data;
1481 struct moschip_port *mos7840_port;
1482 unsigned int result;
1483 __u16 msr;
1484 __u16 mcr;
1485 int status;
1486 mos7840_port = mos7840_get_port_private(port);
1487
1488 if (mos7840_port == NULL)
1489 return -ENODEV;
1490
1491 status = mos7840_get_uart_reg(port, MODEM_STATUS_REGISTER, &msr);
1492 if (status != 1)
1493 return -EIO;
1494 status = mos7840_get_uart_reg(port, MODEM_CONTROL_REGISTER, &mcr);
1495 if (status != 1)
1496 return -EIO;
1497 result = ((mcr & MCR_DTR) ? TIOCM_DTR : 0)
1498 | ((mcr & MCR_RTS) ? TIOCM_RTS : 0)
1499 | ((mcr & MCR_LOOPBACK) ? TIOCM_LOOP : 0)
1500 | ((msr & MOS7840_MSR_CTS) ? TIOCM_CTS : 0)
1501 | ((msr & MOS7840_MSR_CD) ? TIOCM_CAR : 0)
1502 | ((msr & MOS7840_MSR_RI) ? TIOCM_RI : 0)
1503 | ((msr & MOS7840_MSR_DSR) ? TIOCM_DSR : 0);
1504
1505 dev_dbg(&port->dev, "%s - 0x%04X\n", __func__, result);
1506
1507 return result;
1508}
1509
1510static int mos7840_tiocmset(struct tty_struct *tty,
1511 unsigned int set, unsigned int clear)
1512{
1513 struct usb_serial_port *port = tty->driver_data;
1514 struct moschip_port *mos7840_port;
1515 unsigned int mcr;
1516 int status;
1517
1518 mos7840_port = mos7840_get_port_private(port);
1519
1520 if (mos7840_port == NULL)
1521 return -ENODEV;
1522
1523 /* FIXME: What locks the port registers ? */
1524 mcr = mos7840_port->shadowMCR;
1525 if (clear & TIOCM_RTS)
1526 mcr &= ~MCR_RTS;
1527 if (clear & TIOCM_DTR)
1528 mcr &= ~MCR_DTR;
1529 if (clear & TIOCM_LOOP)
1530 mcr &= ~MCR_LOOPBACK;
1531
1532 if (set & TIOCM_RTS)
1533 mcr |= MCR_RTS;
1534 if (set & TIOCM_DTR)
1535 mcr |= MCR_DTR;
1536 if (set & TIOCM_LOOP)
1537 mcr |= MCR_LOOPBACK;
1538
1539 mos7840_port->shadowMCR = mcr;
1540
1541 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, mcr);
1542 if (status < 0) {
1543 dev_dbg(&port->dev, "setting MODEM_CONTROL_REGISTER Failed\n");
1544 return status;
1545 }
1546
1547 return 0;
1548}
1549
1550/*****************************************************************************
1551 * mos7840_calc_baud_rate_divisor
1552 * this function calculates the proper baud rate divisor for the specified
1553 * baud rate.
1554 *****************************************************************************/
1555static int mos7840_calc_baud_rate_divisor(struct usb_serial_port *port,
1556 int baudRate, int *divisor,
1557 __u16 *clk_sel_val)
1558{
1559 dev_dbg(&port->dev, "%s - %d\n", __func__, baudRate);
1560
1561 if (baudRate <= 115200) {
1562 *divisor = 115200 / baudRate;
1563 *clk_sel_val = 0x0;
1564 }
1565 if ((baudRate > 115200) && (baudRate <= 230400)) {
1566 *divisor = 230400 / baudRate;
1567 *clk_sel_val = 0x10;
1568 } else if ((baudRate > 230400) && (baudRate <= 403200)) {
1569 *divisor = 403200 / baudRate;
1570 *clk_sel_val = 0x20;
1571 } else if ((baudRate > 403200) && (baudRate <= 460800)) {
1572 *divisor = 460800 / baudRate;
1573 *clk_sel_val = 0x30;
1574 } else if ((baudRate > 460800) && (baudRate <= 806400)) {
1575 *divisor = 806400 / baudRate;
1576 *clk_sel_val = 0x40;
1577 } else if ((baudRate > 806400) && (baudRate <= 921600)) {
1578 *divisor = 921600 / baudRate;
1579 *clk_sel_val = 0x50;
1580 } else if ((baudRate > 921600) && (baudRate <= 1572864)) {
1581 *divisor = 1572864 / baudRate;
1582 *clk_sel_val = 0x60;
1583 } else if ((baudRate > 1572864) && (baudRate <= 3145728)) {
1584 *divisor = 3145728 / baudRate;
1585 *clk_sel_val = 0x70;
1586 }
1587 return 0;
1588}
1589
1590/*****************************************************************************
1591 * mos7840_send_cmd_write_baud_rate
1592 * this function sends the proper command to change the baud rate of the
1593 * specified port.
1594 *****************************************************************************/
1595
1596static int mos7840_send_cmd_write_baud_rate(struct moschip_port *mos7840_port,
1597 int baudRate)
1598{
1599 int divisor = 0;
1600 int status;
1601 __u16 Data;
1602 unsigned char number;
1603 __u16 clk_sel_val;
1604 struct usb_serial_port *port;
1605
1606 if (mos7840_port == NULL)
1607 return -1;
1608
1609 port = mos7840_port->port;
1610 if (mos7840_port_paranoia_check(port, __func__))
1611 return -1;
1612
1613 if (mos7840_serial_paranoia_check(port->serial, __func__))
1614 return -1;
1615
1616 number = mos7840_port->port->port_number;
1617
1618 dev_dbg(&port->dev, "%s - baud = %d\n", __func__, baudRate);
1619 /* reset clk_uart_sel in spregOffset */
1620 if (baudRate > 115200) {
1621#ifdef HW_flow_control
1622 /* NOTE: need to see the pther register to modify */
1623 /* setting h/w flow control bit to 1 */
1624 Data = 0x2b;
1625 mos7840_port->shadowMCR = Data;
1626 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
1627 Data);
1628 if (status < 0) {
1629 dev_dbg(&port->dev, "Writing spreg failed in set_serial_baud\n");
1630 return -1;
1631 }
1632#endif
1633
1634 } else {
1635#ifdef HW_flow_control
1636 /* setting h/w flow control bit to 0 */
1637 Data = 0xb;
1638 mos7840_port->shadowMCR = Data;
1639 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
1640 Data);
1641 if (status < 0) {
1642 dev_dbg(&port->dev, "Writing spreg failed in set_serial_baud\n");
1643 return -1;
1644 }
1645#endif
1646
1647 }
1648
1649 if (1) { /* baudRate <= 115200) */
1650 clk_sel_val = 0x0;
1651 Data = 0x0;
1652 status = mos7840_calc_baud_rate_divisor(port, baudRate, &divisor,
1653 &clk_sel_val);
1654 status = mos7840_get_reg_sync(port, mos7840_port->SpRegOffset,
1655 &Data);
1656 if (status < 0) {
1657 dev_dbg(&port->dev, "reading spreg failed in set_serial_baud\n");
1658 return -1;
1659 }
1660 Data = (Data & 0x8f) | clk_sel_val;
1661 status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset,
1662 Data);
1663 if (status < 0) {
1664 dev_dbg(&port->dev, "Writing spreg failed in set_serial_baud\n");
1665 return -1;
1666 }
1667 /* Calculate the Divisor */
1668
1669 if (status) {
1670 dev_err(&port->dev, "%s - bad baud rate\n", __func__);
1671 return status;
1672 }
1673 /* Enable access to divisor latch */
1674 Data = mos7840_port->shadowLCR | SERIAL_LCR_DLAB;
1675 mos7840_port->shadowLCR = Data;
1676 mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
1677
1678 /* Write the divisor */
1679 Data = (unsigned char)(divisor & 0xff);
1680 dev_dbg(&port->dev, "set_serial_baud Value to write DLL is %x\n", Data);
1681 mos7840_set_uart_reg(port, DIVISOR_LATCH_LSB, Data);
1682
1683 Data = (unsigned char)((divisor & 0xff00) >> 8);
1684 dev_dbg(&port->dev, "set_serial_baud Value to write DLM is %x\n", Data);
1685 mos7840_set_uart_reg(port, DIVISOR_LATCH_MSB, Data);
1686
1687 /* Disable access to divisor latch */
1688 Data = mos7840_port->shadowLCR & ~SERIAL_LCR_DLAB;
1689 mos7840_port->shadowLCR = Data;
1690 mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
1691
1692 }
1693 return status;
1694}
1695
1696/*****************************************************************************
1697 * mos7840_change_port_settings
1698 * This routine is called to set the UART on the device to match
1699 * the specified new settings.
1700 *****************************************************************************/
1701
1702static void mos7840_change_port_settings(struct tty_struct *tty,
1703 struct moschip_port *mos7840_port, struct ktermios *old_termios)
1704{
1705 int baud;
1706 unsigned cflag;
1707 unsigned iflag;
1708 __u8 lData;
1709 __u8 lParity;
1710 __u8 lStop;
1711 int status;
1712 __u16 Data;
1713 struct usb_serial_port *port;
1714 struct usb_serial *serial;
1715
1716 if (mos7840_port == NULL)
1717 return;
1718
1719 port = mos7840_port->port;
1720
1721 if (mos7840_port_paranoia_check(port, __func__))
1722 return;
1723
1724 if (mos7840_serial_paranoia_check(port->serial, __func__))
1725 return;
1726
1727 serial = port->serial;
1728
1729 if (!mos7840_port->open) {
1730 dev_dbg(&port->dev, "%s - port not opened\n", __func__);
1731 return;
1732 }
1733
1734 lData = LCR_BITS_8;
1735 lStop = LCR_STOP_1;
1736 lParity = LCR_PAR_NONE;
1737
1738 cflag = tty->termios.c_cflag;
1739 iflag = tty->termios.c_iflag;
1740
1741 /* Change the number of bits */
1742 switch (cflag & CSIZE) {
1743 case CS5:
1744 lData = LCR_BITS_5;
1745 break;
1746
1747 case CS6:
1748 lData = LCR_BITS_6;
1749 break;
1750
1751 case CS7:
1752 lData = LCR_BITS_7;
1753 break;
1754
1755 default:
1756 case CS8:
1757 lData = LCR_BITS_8;
1758 break;
1759 }
1760
1761 /* Change the Parity bit */
1762 if (cflag & PARENB) {
1763 if (cflag & PARODD) {
1764 lParity = LCR_PAR_ODD;
1765 dev_dbg(&port->dev, "%s - parity = odd\n", __func__);
1766 } else {
1767 lParity = LCR_PAR_EVEN;
1768 dev_dbg(&port->dev, "%s - parity = even\n", __func__);
1769 }
1770
1771 } else {
1772 dev_dbg(&port->dev, "%s - parity = none\n", __func__);
1773 }
1774
1775 if (cflag & CMSPAR)
1776 lParity = lParity | 0x20;
1777
1778 /* Change the Stop bit */
1779 if (cflag & CSTOPB) {
1780 lStop = LCR_STOP_2;
1781 dev_dbg(&port->dev, "%s - stop bits = 2\n", __func__);
1782 } else {
1783 lStop = LCR_STOP_1;
1784 dev_dbg(&port->dev, "%s - stop bits = 1\n", __func__);
1785 }
1786
1787 /* Update the LCR with the correct value */
1788 mos7840_port->shadowLCR &=
1789 ~(LCR_BITS_MASK | LCR_STOP_MASK | LCR_PAR_MASK);
1790 mos7840_port->shadowLCR |= (lData | lParity | lStop);
1791
1792 dev_dbg(&port->dev, "%s - mos7840_port->shadowLCR is %x\n", __func__,
1793 mos7840_port->shadowLCR);
1794 /* Disable Interrupts */
1795 Data = 0x00;
1796 mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
1797
1798 Data = 0x00;
1799 mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
1800
1801 Data = 0xcf;
1802 mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
1803
1804 /* Send the updated LCR value to the mos7840 */
1805 Data = mos7840_port->shadowLCR;
1806
1807 mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
1808
1809 Data = 0x00b;
1810 mos7840_port->shadowMCR = Data;
1811 mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
1812 Data = 0x00b;
1813 mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
1814
1815 /* set up the MCR register and send it to the mos7840 */
1816
1817 mos7840_port->shadowMCR = MCR_MASTER_IE;
1818 if (cflag & CBAUD)
1819 mos7840_port->shadowMCR |= (MCR_DTR | MCR_RTS);
1820
1821 if (cflag & CRTSCTS)
1822 mos7840_port->shadowMCR |= (MCR_XON_ANY);
1823 else
1824 mos7840_port->shadowMCR &= ~(MCR_XON_ANY);
1825
1826 Data = mos7840_port->shadowMCR;
1827 mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
1828
1829 /* Determine divisor based on baud rate */
1830 baud = tty_get_baud_rate(tty);
1831
1832 if (!baud) {
1833 /* pick a default, any default... */
1834 dev_dbg(&port->dev, "%s", "Picked default baud...\n");
1835 baud = 9600;
1836 }
1837
1838 dev_dbg(&port->dev, "%s - baud rate = %d\n", __func__, baud);
1839 status = mos7840_send_cmd_write_baud_rate(mos7840_port, baud);
1840
1841 /* Enable Interrupts */
1842 Data = 0x0c;
1843 mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
1844
1845 if (!mos7840_port->read_urb_busy) {
1846 mos7840_port->read_urb_busy = true;
1847 status = usb_submit_urb(mos7840_port->read_urb, GFP_KERNEL);
1848 if (status) {
1849 dev_dbg(&port->dev, "usb_submit_urb(read bulk) failed, status = %d\n",
1850 status);
1851 mos7840_port->read_urb_busy = false;
1852 }
1853 }
1854 dev_dbg(&port->dev, "%s - mos7840_port->shadowLCR is End %x\n", __func__,
1855 mos7840_port->shadowLCR);
1856}
1857
1858/*****************************************************************************
1859 * mos7840_set_termios
1860 * this function is called by the tty driver when it wants to change
1861 * the termios structure
1862 *****************************************************************************/
1863
1864static void mos7840_set_termios(struct tty_struct *tty,
1865 struct usb_serial_port *port,
1866 struct ktermios *old_termios)
1867{
1868 int status;
1869 unsigned int cflag;
1870 struct usb_serial *serial;
1871 struct moschip_port *mos7840_port;
1872
1873 if (mos7840_port_paranoia_check(port, __func__))
1874 return;
1875
1876 serial = port->serial;
1877
1878 if (mos7840_serial_paranoia_check(serial, __func__))
1879 return;
1880
1881 mos7840_port = mos7840_get_port_private(port);
1882
1883 if (mos7840_port == NULL)
1884 return;
1885
1886 if (!mos7840_port->open) {
1887 dev_dbg(&port->dev, "%s - port not opened\n", __func__);
1888 return;
1889 }
1890
1891 dev_dbg(&port->dev, "%s", "setting termios - \n");
1892
1893 cflag = tty->termios.c_cflag;
1894
1895 dev_dbg(&port->dev, "%s - clfag %08x iflag %08x\n", __func__,
1896 tty->termios.c_cflag, RELEVANT_IFLAG(tty->termios.c_iflag));
1897 dev_dbg(&port->dev, "%s - old clfag %08x old iflag %08x\n", __func__,
1898 old_termios->c_cflag, RELEVANT_IFLAG(old_termios->c_iflag));
1899
1900 /* change the port settings to the new ones specified */
1901
1902 mos7840_change_port_settings(tty, mos7840_port, old_termios);
1903
1904 if (!mos7840_port->read_urb) {
1905 dev_dbg(&port->dev, "%s", "URB KILLED !!!!!\n");
1906 return;
1907 }
1908
1909 if (!mos7840_port->read_urb_busy) {
1910 mos7840_port->read_urb_busy = true;
1911 status = usb_submit_urb(mos7840_port->read_urb, GFP_KERNEL);
1912 if (status) {
1913 dev_dbg(&port->dev, "usb_submit_urb(read bulk) failed, status = %d\n",
1914 status);
1915 mos7840_port->read_urb_busy = false;
1916 }
1917 }
1918}
1919
1920/*****************************************************************************
1921 * mos7840_get_lsr_info - get line status register info
1922 *
1923 * Purpose: Let user call ioctl() to get info when the UART physically
1924 * is emptied. On bus types like RS485, the transmitter must
1925 * release the bus after transmitting. This must be done when
1926 * the transmit shift register is empty, not be done when the
1927 * transmit holding register is empty. This functionality
1928 * allows an RS485 driver to be written in user space.
1929 *****************************************************************************/
1930
1931static int mos7840_get_lsr_info(struct tty_struct *tty,
1932 unsigned int __user *value)
1933{
1934 int count;
1935 unsigned int result = 0;
1936
1937 count = mos7840_chars_in_buffer(tty);
1938 if (count == 0)
1939 result = TIOCSER_TEMT;
1940
1941 if (copy_to_user(value, &result, sizeof(int)))
1942 return -EFAULT;
1943 return 0;
1944}
1945
1946/*****************************************************************************
1947 * mos7840_get_serial_info
1948 * function to get information about serial port
1949 *****************************************************************************/
1950
1951static int mos7840_get_serial_info(struct moschip_port *mos7840_port,
1952 struct serial_struct __user *retinfo)
1953{
1954 struct serial_struct tmp;
1955
1956 if (mos7840_port == NULL)
1957 return -1;
1958
1959 if (!retinfo)
1960 return -EFAULT;
1961
1962 memset(&tmp, 0, sizeof(tmp));
1963
1964 tmp.type = PORT_16550A;
1965 tmp.line = mos7840_port->port->minor;
1966 tmp.port = mos7840_port->port->port_number;
1967 tmp.irq = 0;
1968 tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ;
1969 tmp.xmit_fifo_size = NUM_URBS * URB_TRANSFER_BUFFER_SIZE;
1970 tmp.baud_base = 9600;
1971 tmp.close_delay = 5 * HZ;
1972 tmp.closing_wait = 30 * HZ;
1973
1974 if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
1975 return -EFAULT;
1976 return 0;
1977}
1978
1979/*****************************************************************************
1980 * SerialIoctl
1981 * this function handles any ioctl calls to the driver
1982 *****************************************************************************/
1983
1984static int mos7840_ioctl(struct tty_struct *tty,
1985 unsigned int cmd, unsigned long arg)
1986{
1987 struct usb_serial_port *port = tty->driver_data;
1988 void __user *argp = (void __user *)arg;
1989 struct moschip_port *mos7840_port;
1990
1991 if (mos7840_port_paranoia_check(port, __func__))
1992 return -1;
1993
1994 mos7840_port = mos7840_get_port_private(port);
1995
1996 if (mos7840_port == NULL)
1997 return -1;
1998
1999 switch (cmd) {
2000 /* return number of bytes available */
2001
2002 case TIOCSERGETLSR:
2003 dev_dbg(&port->dev, "%s TIOCSERGETLSR\n", __func__);
2004 return mos7840_get_lsr_info(tty, argp);
2005
2006 case TIOCGSERIAL:
2007 dev_dbg(&port->dev, "%s TIOCGSERIAL\n", __func__);
2008 return mos7840_get_serial_info(mos7840_port, argp);
2009
2010 case TIOCSSERIAL:
2011 dev_dbg(&port->dev, "%s TIOCSSERIAL\n", __func__);
2012 break;
2013 default:
2014 break;
2015 }
2016 return -ENOIOCTLCMD;
2017}
2018
2019static int mos7810_check(struct usb_serial *serial)
2020{
2021 int i, pass_count = 0;
2022 u8 *buf;
2023 __u16 data = 0, mcr_data = 0;
2024 __u16 test_pattern = 0x55AA;
2025 int res;
2026
2027 buf = kmalloc(VENDOR_READ_LENGTH, GFP_KERNEL);
2028 if (!buf)
2029 return 0; /* failed to identify 7810 */
2030
2031 /* Store MCR setting */
2032 res = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
2033 MCS_RDREQ, MCS_RD_RTYPE, 0x0300, MODEM_CONTROL_REGISTER,
2034 buf, VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT);
2035 if (res == VENDOR_READ_LENGTH)
2036 mcr_data = *buf;
2037
2038 for (i = 0; i < 16; i++) {
2039 /* Send the 1-bit test pattern out to MCS7810 test pin */
2040 usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
2041 MCS_WRREQ, MCS_WR_RTYPE,
2042 (0x0300 | (((test_pattern >> i) & 0x0001) << 1)),
2043 MODEM_CONTROL_REGISTER, NULL, 0, MOS_WDR_TIMEOUT);
2044
2045 /* Read the test pattern back */
2046 res = usb_control_msg(serial->dev,
2047 usb_rcvctrlpipe(serial->dev, 0), MCS_RDREQ,
2048 MCS_RD_RTYPE, 0, GPIO_REGISTER, buf,
2049 VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT);
2050 if (res == VENDOR_READ_LENGTH)
2051 data = *buf;
2052
2053 /* If this is a MCS7810 device, both test patterns must match */
2054 if (((test_pattern >> i) ^ (~data >> 1)) & 0x0001)
2055 break;
2056
2057 pass_count++;
2058 }
2059
2060 /* Restore MCR setting */
2061 usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), MCS_WRREQ,
2062 MCS_WR_RTYPE, 0x0300 | mcr_data, MODEM_CONTROL_REGISTER, NULL,
2063 0, MOS_WDR_TIMEOUT);
2064
2065 kfree(buf);
2066
2067 if (pass_count == 16)
2068 return 1;
2069
2070 return 0;
2071}
2072
2073static int mos7840_probe(struct usb_serial *serial,
2074 const struct usb_device_id *id)
2075{
2076 u16 product = le16_to_cpu(serial->dev->descriptor.idProduct);
2077 u8 *buf;
2078 int device_type;
2079
2080 if (product == MOSCHIP_DEVICE_ID_7810 ||
2081 product == MOSCHIP_DEVICE_ID_7820) {
2082 device_type = product;
2083 goto out;
2084 }
2085
2086 buf = kzalloc(VENDOR_READ_LENGTH, GFP_KERNEL);
2087 if (!buf)
2088 return -ENOMEM;
2089
2090 usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
2091 MCS_RDREQ, MCS_RD_RTYPE, 0, GPIO_REGISTER, buf,
2092 VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT);
2093
2094 /* For a MCS7840 device GPIO0 must be set to 1 */
2095 if (buf[0] & 0x01)
2096 device_type = MOSCHIP_DEVICE_ID_7840;
2097 else if (mos7810_check(serial))
2098 device_type = MOSCHIP_DEVICE_ID_7810;
2099 else
2100 device_type = MOSCHIP_DEVICE_ID_7820;
2101
2102 kfree(buf);
2103out:
2104 usb_set_serial_data(serial, (void *)(unsigned long)device_type);
2105
2106 return 0;
2107}
2108
2109static int mos7840_calc_num_ports(struct usb_serial *serial)
2110{
2111 int device_type = (unsigned long)usb_get_serial_data(serial);
2112 int mos7840_num_ports;
2113
2114 mos7840_num_ports = (device_type >> 4) & 0x000F;
2115
2116 return mos7840_num_ports;
2117}
2118
2119static int mos7840_port_probe(struct usb_serial_port *port)
2120{
2121 struct usb_serial *serial = port->serial;
2122 int device_type = (unsigned long)usb_get_serial_data(serial);
2123 struct moschip_port *mos7840_port;
2124 int status;
2125 int pnum;
2126 __u16 Data;
2127
2128 /* we set up the pointers to the endpoints in the mos7840_open *
2129 * function, as the structures aren't created yet. */
2130
2131 pnum = port->port_number;
2132
2133 dev_dbg(&port->dev, "mos7840_startup: configuring port %d\n", pnum);
2134 mos7840_port = kzalloc(sizeof(struct moschip_port), GFP_KERNEL);
2135 if (!mos7840_port)
2136 return -ENOMEM;
2137
2138 /* Initialize all port interrupt end point to port 0 int
2139 * endpoint. Our device has only one interrupt end point
2140 * common to all port */
2141
2142 mos7840_port->port = port;
2143 mos7840_set_port_private(port, mos7840_port);
2144 spin_lock_init(&mos7840_port->pool_lock);
2145
2146 /* minor is not initialised until later by
2147 * usb-serial.c:get_free_serial() and cannot therefore be used
2148 * to index device instances */
2149 mos7840_port->port_num = pnum + 1;
2150 dev_dbg(&port->dev, "port->minor = %d\n", port->minor);
2151 dev_dbg(&port->dev, "mos7840_port->port_num = %d\n", mos7840_port->port_num);
2152
2153 if (mos7840_port->port_num == 1) {
2154 mos7840_port->SpRegOffset = 0x0;
2155 mos7840_port->ControlRegOffset = 0x1;
2156 mos7840_port->DcrRegOffset = 0x4;
2157 } else if ((mos7840_port->port_num == 2) && (serial->num_ports == 4)) {
2158 mos7840_port->SpRegOffset = 0x8;
2159 mos7840_port->ControlRegOffset = 0x9;
2160 mos7840_port->DcrRegOffset = 0x16;
2161 } else if ((mos7840_port->port_num == 2) && (serial->num_ports == 2)) {
2162 mos7840_port->SpRegOffset = 0xa;
2163 mos7840_port->ControlRegOffset = 0xb;
2164 mos7840_port->DcrRegOffset = 0x19;
2165 } else if ((mos7840_port->port_num == 3) && (serial->num_ports == 4)) {
2166 mos7840_port->SpRegOffset = 0xa;
2167 mos7840_port->ControlRegOffset = 0xb;
2168 mos7840_port->DcrRegOffset = 0x19;
2169 } else if ((mos7840_port->port_num == 4) && (serial->num_ports == 4)) {
2170 mos7840_port->SpRegOffset = 0xc;
2171 mos7840_port->ControlRegOffset = 0xd;
2172 mos7840_port->DcrRegOffset = 0x1c;
2173 }
2174 mos7840_dump_serial_port(port, mos7840_port);
2175 mos7840_set_port_private(port, mos7840_port);
2176
2177 /* enable rx_disable bit in control register */
2178 status = mos7840_get_reg_sync(port,
2179 mos7840_port->ControlRegOffset, &Data);
2180 if (status < 0) {
2181 dev_dbg(&port->dev, "Reading ControlReg failed status-0x%x\n", status);
2182 goto out;
2183 } else
2184 dev_dbg(&port->dev, "ControlReg Reading success val is %x, status%d\n", Data, status);
2185 Data |= 0x08; /* setting driver done bit */
2186 Data |= 0x04; /* sp1_bit to have cts change reflect in
2187 modem status reg */
2188
2189 /* Data |= 0x20; //rx_disable bit */
2190 status = mos7840_set_reg_sync(port,
2191 mos7840_port->ControlRegOffset, Data);
2192 if (status < 0) {
2193 dev_dbg(&port->dev, "Writing ControlReg failed(rx_disable) status-0x%x\n", status);
2194 goto out;
2195 } else
2196 dev_dbg(&port->dev, "ControlReg Writing success(rx_disable) status%d\n", status);
2197
2198 /* Write default values in DCR (i.e 0x01 in DCR0, 0x05 in DCR2
2199 and 0x24 in DCR3 */
2200 Data = 0x01;
2201 status = mos7840_set_reg_sync(port,
2202 (__u16) (mos7840_port->DcrRegOffset + 0), Data);
2203 if (status < 0) {
2204 dev_dbg(&port->dev, "Writing DCR0 failed status-0x%x\n", status);
2205 goto out;
2206 } else
2207 dev_dbg(&port->dev, "DCR0 Writing success status%d\n", status);
2208
2209 Data = 0x05;
2210 status = mos7840_set_reg_sync(port,
2211 (__u16) (mos7840_port->DcrRegOffset + 1), Data);
2212 if (status < 0) {
2213 dev_dbg(&port->dev, "Writing DCR1 failed status-0x%x\n", status);
2214 goto out;
2215 } else
2216 dev_dbg(&port->dev, "DCR1 Writing success status%d\n", status);
2217
2218 Data = 0x24;
2219 status = mos7840_set_reg_sync(port,
2220 (__u16) (mos7840_port->DcrRegOffset + 2), Data);
2221 if (status < 0) {
2222 dev_dbg(&port->dev, "Writing DCR2 failed status-0x%x\n", status);
2223 goto out;
2224 } else
2225 dev_dbg(&port->dev, "DCR2 Writing success status%d\n", status);
2226
2227 /* write values in clkstart0x0 and clkmulti 0x20 */
2228 Data = 0x0;
2229 status = mos7840_set_reg_sync(port, CLK_START_VALUE_REGISTER, Data);
2230 if (status < 0) {
2231 dev_dbg(&port->dev, "Writing CLK_START_VALUE_REGISTER failed status-0x%x\n", status);
2232 goto out;
2233 } else
2234 dev_dbg(&port->dev, "CLK_START_VALUE_REGISTER Writing success status%d\n", status);
2235
2236 Data = 0x20;
2237 status = mos7840_set_reg_sync(port, CLK_MULTI_REGISTER, Data);
2238 if (status < 0) {
2239 dev_dbg(&port->dev, "Writing CLK_MULTI_REGISTER failed status-0x%x\n", status);
2240 goto error;
2241 } else
2242 dev_dbg(&port->dev, "CLK_MULTI_REGISTER Writing success status%d\n", status);
2243
2244 /* write value 0x0 to scratchpad register */
2245 Data = 0x00;
2246 status = mos7840_set_uart_reg(port, SCRATCH_PAD_REGISTER, Data);
2247 if (status < 0) {
2248 dev_dbg(&port->dev, "Writing SCRATCH_PAD_REGISTER failed status-0x%x\n", status);
2249 goto out;
2250 } else
2251 dev_dbg(&port->dev, "SCRATCH_PAD_REGISTER Writing success status%d\n", status);
2252
2253 /* Zero Length flag register */
2254 if ((mos7840_port->port_num != 1) && (serial->num_ports == 2)) {
2255 Data = 0xff;
2256 status = mos7840_set_reg_sync(port,
2257 (__u16) (ZLP_REG1 +
2258 ((__u16)mos7840_port->port_num)), Data);
2259 dev_dbg(&port->dev, "ZLIP offset %x\n",
2260 (__u16)(ZLP_REG1 + ((__u16) mos7840_port->port_num)));
2261 if (status < 0) {
2262 dev_dbg(&port->dev, "Writing ZLP_REG%d failed status-0x%x\n", pnum + 2, status);
2263 goto out;
2264 } else
2265 dev_dbg(&port->dev, "ZLP_REG%d Writing success status%d\n", pnum + 2, status);
2266 } else {
2267 Data = 0xff;
2268 status = mos7840_set_reg_sync(port,
2269 (__u16) (ZLP_REG1 +
2270 ((__u16)mos7840_port->port_num) - 0x1), Data);
2271 dev_dbg(&port->dev, "ZLIP offset %x\n",
2272 (__u16)(ZLP_REG1 + ((__u16) mos7840_port->port_num) - 0x1));
2273 if (status < 0) {
2274 dev_dbg(&port->dev, "Writing ZLP_REG%d failed status-0x%x\n", pnum + 1, status);
2275 goto out;
2276 } else
2277 dev_dbg(&port->dev, "ZLP_REG%d Writing success status%d\n", pnum + 1, status);
2278
2279 }
2280 mos7840_port->control_urb = usb_alloc_urb(0, GFP_KERNEL);
2281 mos7840_port->ctrl_buf = kmalloc(16, GFP_KERNEL);
2282 mos7840_port->dr = kmalloc(sizeof(struct usb_ctrlrequest),
2283 GFP_KERNEL);
2284 if (!mos7840_port->control_urb || !mos7840_port->ctrl_buf ||
2285 !mos7840_port->dr) {
2286 status = -ENOMEM;
2287 goto error;
2288 }
2289
2290 mos7840_port->has_led = false;
2291
2292 /* Initialize LED timers */
2293 if (device_type == MOSCHIP_DEVICE_ID_7810) {
2294 mos7840_port->has_led = true;
2295
2296 mos7840_port->led_urb = usb_alloc_urb(0, GFP_KERNEL);
2297 mos7840_port->led_dr = kmalloc(sizeof(*mos7840_port->led_dr),
2298 GFP_KERNEL);
2299 if (!mos7840_port->led_urb || !mos7840_port->led_dr) {
2300 status = -ENOMEM;
2301 goto error;
2302 }
2303
2304 setup_timer(&mos7840_port->led_timer1, mos7840_led_off,
2305 (unsigned long)mos7840_port);
2306 mos7840_port->led_timer1.expires =
2307 jiffies + msecs_to_jiffies(LED_ON_MS);
2308 setup_timer(&mos7840_port->led_timer2, mos7840_led_flag_off,
2309 (unsigned long)mos7840_port);
2310 mos7840_port->led_timer2.expires =
2311 jiffies + msecs_to_jiffies(LED_OFF_MS);
2312
2313 /* Turn off LED */
2314 mos7840_set_led_sync(port, MODEM_CONTROL_REGISTER, 0x0300);
2315 }
2316out:
2317 if (pnum == serial->num_ports - 1) {
2318 /* Zero Length flag enable */
2319 Data = 0x0f;
2320 status = mos7840_set_reg_sync(serial->port[0], ZLP_REG5, Data);
2321 if (status < 0) {
2322 dev_dbg(&port->dev, "Writing ZLP_REG5 failed status-0x%x\n", status);
2323 goto error;
2324 } else
2325 dev_dbg(&port->dev, "ZLP_REG5 Writing success status%d\n", status);
2326
2327 /* setting configuration feature to one */
2328 usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
2329 0x03, 0x00, 0x01, 0x00, NULL, 0x00,
2330 MOS_WDR_TIMEOUT);
2331 }
2332 return 0;
2333error:
2334 kfree(mos7840_port->led_dr);
2335 usb_free_urb(mos7840_port->led_urb);
2336 kfree(mos7840_port->dr);
2337 kfree(mos7840_port->ctrl_buf);
2338 usb_free_urb(mos7840_port->control_urb);
2339 kfree(mos7840_port);
2340
2341 return status;
2342}
2343
2344static int mos7840_port_remove(struct usb_serial_port *port)
2345{
2346 struct moschip_port *mos7840_port;
2347
2348 mos7840_port = mos7840_get_port_private(port);
2349
2350 if (mos7840_port->has_led) {
2351 /* Turn off LED */
2352 mos7840_set_led_sync(port, MODEM_CONTROL_REGISTER, 0x0300);
2353
2354 del_timer_sync(&mos7840_port->led_timer1);
2355 del_timer_sync(&mos7840_port->led_timer2);
2356
2357 usb_kill_urb(mos7840_port->led_urb);
2358 usb_free_urb(mos7840_port->led_urb);
2359 kfree(mos7840_port->led_dr);
2360 }
2361 usb_kill_urb(mos7840_port->control_urb);
2362 usb_free_urb(mos7840_port->control_urb);
2363 kfree(mos7840_port->ctrl_buf);
2364 kfree(mos7840_port->dr);
2365 kfree(mos7840_port);
2366
2367 return 0;
2368}
2369
2370static struct usb_serial_driver moschip7840_4port_device = {
2371 .driver = {
2372 .owner = THIS_MODULE,
2373 .name = "mos7840",
2374 },
2375 .description = DRIVER_DESC,
2376 .id_table = id_table,
2377 .num_ports = 4,
2378 .open = mos7840_open,
2379 .close = mos7840_close,
2380 .write = mos7840_write,
2381 .write_room = mos7840_write_room,
2382 .chars_in_buffer = mos7840_chars_in_buffer,
2383 .throttle = mos7840_throttle,
2384 .unthrottle = mos7840_unthrottle,
2385 .calc_num_ports = mos7840_calc_num_ports,
2386 .probe = mos7840_probe,
2387 .ioctl = mos7840_ioctl,
2388 .set_termios = mos7840_set_termios,
2389 .break_ctl = mos7840_break,
2390 .tiocmget = mos7840_tiocmget,
2391 .tiocmset = mos7840_tiocmset,
2392 .tiocmiwait = usb_serial_generic_tiocmiwait,
2393 .get_icount = usb_serial_generic_get_icount,
2394 .port_probe = mos7840_port_probe,
2395 .port_remove = mos7840_port_remove,
2396 .read_bulk_callback = mos7840_bulk_in_callback,
2397 .read_int_callback = mos7840_interrupt_callback,
2398};
2399
2400static struct usb_serial_driver * const serial_drivers[] = {
2401 &moschip7840_4port_device, NULL
2402};
2403
2404module_usb_serial_driver(serial_drivers, id_table);
2405
2406MODULE_DESCRIPTION(DRIVER_DESC);
2407MODULE_LICENSE("GPL");
1// SPDX-License-Identifier: GPL-2.0+
2/*
3 * Clean ups from Moschip version and a few ioctl implementations by:
4 * Paul B Schroeder <pschroeder "at" uplogix "dot" com>
5 *
6 * Originally based on drivers/usb/serial/io_edgeport.c which is:
7 * Copyright (C) 2000 Inside Out Networks, All rights reserved.
8 * Copyright (C) 2001-2002 Greg Kroah-Hartman <greg@kroah.com>
9 *
10 */
11
12#include <linux/kernel.h>
13#include <linux/errno.h>
14#include <linux/slab.h>
15#include <linux/tty.h>
16#include <linux/tty_driver.h>
17#include <linux/tty_flip.h>
18#include <linux/module.h>
19#include <linux/serial.h>
20#include <linux/usb.h>
21#include <linux/usb/serial.h>
22#include <linux/uaccess.h>
23
24#define DRIVER_DESC "Moschip 7840/7820 USB Serial Driver"
25
26/*
27 * 16C50 UART register defines
28 */
29
30#define LCR_BITS_5 0x00 /* 5 bits/char */
31#define LCR_BITS_6 0x01 /* 6 bits/char */
32#define LCR_BITS_7 0x02 /* 7 bits/char */
33#define LCR_BITS_8 0x03 /* 8 bits/char */
34#define LCR_BITS_MASK 0x03 /* Mask for bits/char field */
35
36#define LCR_STOP_1 0x00 /* 1 stop bit */
37#define LCR_STOP_1_5 0x04 /* 1.5 stop bits (if 5 bits/char) */
38#define LCR_STOP_2 0x04 /* 2 stop bits (if 6-8 bits/char) */
39#define LCR_STOP_MASK 0x04 /* Mask for stop bits field */
40
41#define LCR_PAR_NONE 0x00 /* No parity */
42#define LCR_PAR_ODD 0x08 /* Odd parity */
43#define LCR_PAR_EVEN 0x18 /* Even parity */
44#define LCR_PAR_MARK 0x28 /* Force parity bit to 1 */
45#define LCR_PAR_SPACE 0x38 /* Force parity bit to 0 */
46#define LCR_PAR_MASK 0x38 /* Mask for parity field */
47
48#define LCR_SET_BREAK 0x40 /* Set Break condition */
49#define LCR_DL_ENABLE 0x80 /* Enable access to divisor latch */
50
51#define MCR_DTR 0x01 /* Assert DTR */
52#define MCR_RTS 0x02 /* Assert RTS */
53#define MCR_OUT1 0x04 /* Loopback only: Sets state of RI */
54#define MCR_MASTER_IE 0x08 /* Enable interrupt outputs */
55#define MCR_LOOPBACK 0x10 /* Set internal (digital) loopback mode */
56#define MCR_XON_ANY 0x20 /* Enable any char to exit XOFF mode */
57
58#define MOS7840_MSR_CTS 0x10 /* Current state of CTS */
59#define MOS7840_MSR_DSR 0x20 /* Current state of DSR */
60#define MOS7840_MSR_RI 0x40 /* Current state of RI */
61#define MOS7840_MSR_CD 0x80 /* Current state of CD */
62
63/*
64 * Defines used for sending commands to port
65 */
66
67#define MOS_WDR_TIMEOUT 5000 /* default urb timeout */
68
69#define MOS_PORT1 0x0200
70#define MOS_PORT2 0x0300
71#define MOS_VENREG 0x0000
72#define MOS_MAX_PORT 0x02
73#define MOS_WRITE 0x0E
74#define MOS_READ 0x0D
75
76/* Requests */
77#define MCS_RD_RTYPE 0xC0
78#define MCS_WR_RTYPE 0x40
79#define MCS_RDREQ 0x0D
80#define MCS_WRREQ 0x0E
81#define MCS_CTRL_TIMEOUT 500
82#define VENDOR_READ_LENGTH (0x01)
83
84#define MAX_NAME_LEN 64
85
86#define ZLP_REG1 0x3A /* Zero_Flag_Reg1 58 */
87#define ZLP_REG5 0x3E /* Zero_Flag_Reg5 62 */
88
89/* For higher baud Rates use TIOCEXBAUD */
90#define TIOCEXBAUD 0x5462
91
92/*
93 * Vendor id and device id defines
94 *
95 * NOTE: Do not add new defines, add entries directly to the id_table instead.
96 */
97#define USB_VENDOR_ID_BANDB 0x0856
98#define BANDB_DEVICE_ID_USO9ML2_2 0xAC22
99#define BANDB_DEVICE_ID_USO9ML2_2P 0xBC00
100#define BANDB_DEVICE_ID_USO9ML2_4 0xAC24
101#define BANDB_DEVICE_ID_USO9ML2_4P 0xBC01
102#define BANDB_DEVICE_ID_US9ML2_2 0xAC29
103#define BANDB_DEVICE_ID_US9ML2_4 0xAC30
104#define BANDB_DEVICE_ID_USPTL4_2 0xAC31
105#define BANDB_DEVICE_ID_USPTL4_4 0xAC32
106#define BANDB_DEVICE_ID_USOPTL4_2 0xAC42
107#define BANDB_DEVICE_ID_USOPTL4_2P 0xBC02
108#define BANDB_DEVICE_ID_USOPTL4_4 0xAC44
109#define BANDB_DEVICE_ID_USOPTL4_4P 0xBC03
110#define BANDB_DEVICE_ID_USOPTL2_4 0xAC24
111
112/* Interrupt Routine Defines */
113
114#define SERIAL_IIR_RLS 0x06
115#define SERIAL_IIR_MS 0x00
116
117/*
118 * Emulation of the bit mask on the LINE STATUS REGISTER.
119 */
120#define SERIAL_LSR_DR 0x0001
121#define SERIAL_LSR_OE 0x0002
122#define SERIAL_LSR_PE 0x0004
123#define SERIAL_LSR_FE 0x0008
124#define SERIAL_LSR_BI 0x0010
125
126#define MOS_MSR_DELTA_CTS 0x10
127#define MOS_MSR_DELTA_DSR 0x20
128#define MOS_MSR_DELTA_RI 0x40
129#define MOS_MSR_DELTA_CD 0x80
130
131/* Serial Port register Address */
132#define INTERRUPT_ENABLE_REGISTER ((__u16)(0x01))
133#define FIFO_CONTROL_REGISTER ((__u16)(0x02))
134#define LINE_CONTROL_REGISTER ((__u16)(0x03))
135#define MODEM_CONTROL_REGISTER ((__u16)(0x04))
136#define LINE_STATUS_REGISTER ((__u16)(0x05))
137#define MODEM_STATUS_REGISTER ((__u16)(0x06))
138#define SCRATCH_PAD_REGISTER ((__u16)(0x07))
139#define DIVISOR_LATCH_LSB ((__u16)(0x00))
140#define DIVISOR_LATCH_MSB ((__u16)(0x01))
141
142#define CLK_MULTI_REGISTER ((__u16)(0x02))
143#define CLK_START_VALUE_REGISTER ((__u16)(0x03))
144#define GPIO_REGISTER ((__u16)(0x07))
145
146#define SERIAL_LCR_DLAB ((__u16)(0x0080))
147
148/*
149 * URB POOL related defines
150 */
151#define NUM_URBS 16 /* URB Count */
152#define URB_TRANSFER_BUFFER_SIZE 32 /* URB Size */
153
154/* LED on/off milliseconds*/
155#define LED_ON_MS 500
156#define LED_OFF_MS 500
157
158enum mos7840_flag {
159 MOS7840_FLAG_LED_BUSY,
160};
161
162#define MCS_PORT_MASK GENMASK(2, 0)
163#define MCS_PORTS(nr) ((nr) & MCS_PORT_MASK)
164#define MCS_LED BIT(3)
165
166#define MCS_DEVICE(vid, pid, flags) \
167 USB_DEVICE((vid), (pid)), .driver_info = (flags)
168
169static const struct usb_device_id id_table[] = {
170 { MCS_DEVICE(0x0557, 0x2011, MCS_PORTS(4)) }, /* ATEN UC2324 */
171 { MCS_DEVICE(0x0557, 0x7820, MCS_PORTS(2)) }, /* ATEN UC2322 */
172 { MCS_DEVICE(0x110a, 0x2210, MCS_PORTS(2)) }, /* Moxa UPort 2210 */
173 { MCS_DEVICE(0x9710, 0x7810, MCS_PORTS(1) | MCS_LED) }, /* ASIX MCS7810 */
174 { MCS_DEVICE(0x9710, 0x7820, MCS_PORTS(2)) }, /* MosChip MCS7820 */
175 { MCS_DEVICE(0x9710, 0x7840, MCS_PORTS(4)) }, /* MosChip MCS7840 */
176 { MCS_DEVICE(0x9710, 0x7843, MCS_PORTS(3)) }, /* ASIX MCS7840 3 port */
177 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_2) },
178 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_2P) },
179 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_4) },
180 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_4P) },
181 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_US9ML2_2) },
182 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_US9ML2_4) },
183 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USPTL4_2) },
184 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USPTL4_4) },
185 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2) },
186 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2P) },
187 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4) },
188 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4P) },
189 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL2_4) },
190 {} /* terminating entry */
191};
192MODULE_DEVICE_TABLE(usb, id_table);
193
194/* This structure holds all of the local port information */
195
196struct moschip_port {
197 int port_num; /*Actual port number in the device(1,2,etc) */
198 struct urb *read_urb; /* read URB for this port */
199 __u8 shadowLCR; /* last LCR value received */
200 __u8 shadowMCR; /* last MCR value received */
201 struct usb_serial_port *port; /* loop back to the owner of this object */
202
203 /* Offsets */
204 __u8 SpRegOffset;
205 __u8 ControlRegOffset;
206 __u8 DcrRegOffset;
207
208 spinlock_t pool_lock;
209 struct urb *write_urb_pool[NUM_URBS];
210 char busy[NUM_URBS];
211 bool read_urb_busy;
212
213 /* For device(s) with LED indicator */
214 bool has_led;
215 struct timer_list led_timer1; /* Timer for LED on */
216 struct timer_list led_timer2; /* Timer for LED off */
217 struct urb *led_urb;
218 struct usb_ctrlrequest *led_dr;
219
220 unsigned long flags;
221};
222
223/*
224 * mos7840_set_reg_sync
225 * To set the Control register by calling usb_fill_control_urb function
226 * by passing usb_sndctrlpipe function as parameter.
227 */
228
229static int mos7840_set_reg_sync(struct usb_serial_port *port, __u16 reg,
230 __u16 val)
231{
232 struct usb_device *dev = port->serial->dev;
233 val = val & 0x00ff;
234 dev_dbg(&port->dev, "mos7840_set_reg_sync offset is %x, value %x\n", reg, val);
235
236 return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), MCS_WRREQ,
237 MCS_WR_RTYPE, val, reg, NULL, 0,
238 MOS_WDR_TIMEOUT);
239}
240
241/*
242 * mos7840_get_reg_sync
243 * To set the Uart register by calling usb_fill_control_urb function by
244 * passing usb_rcvctrlpipe function as parameter.
245 */
246
247static int mos7840_get_reg_sync(struct usb_serial_port *port, __u16 reg,
248 __u16 *val)
249{
250 struct usb_device *dev = port->serial->dev;
251 int ret = 0;
252 u8 *buf;
253
254 buf = kmalloc(VENDOR_READ_LENGTH, GFP_KERNEL);
255 if (!buf)
256 return -ENOMEM;
257
258 ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), MCS_RDREQ,
259 MCS_RD_RTYPE, 0, reg, buf, VENDOR_READ_LENGTH,
260 MOS_WDR_TIMEOUT);
261 if (ret < VENDOR_READ_LENGTH) {
262 if (ret >= 0)
263 ret = -EIO;
264 goto out;
265 }
266
267 *val = buf[0];
268 dev_dbg(&port->dev, "%s offset is %x, return val %x\n", __func__, reg, *val);
269out:
270 kfree(buf);
271 return ret;
272}
273
274/*
275 * mos7840_set_uart_reg
276 * To set the Uart register by calling usb_fill_control_urb function by
277 * passing usb_sndctrlpipe function as parameter.
278 */
279
280static int mos7840_set_uart_reg(struct usb_serial_port *port, __u16 reg,
281 __u16 val)
282{
283
284 struct usb_device *dev = port->serial->dev;
285 val = val & 0x00ff;
286 /* For the UART control registers, the application number need
287 to be Or'ed */
288 if (port->serial->num_ports == 2 && port->port_number != 0)
289 val |= ((__u16)port->port_number + 2) << 8;
290 else
291 val |= ((__u16)port->port_number + 1) << 8;
292 dev_dbg(&port->dev, "%s application number is %x\n", __func__, val);
293 return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), MCS_WRREQ,
294 MCS_WR_RTYPE, val, reg, NULL, 0,
295 MOS_WDR_TIMEOUT);
296
297}
298
299/*
300 * mos7840_get_uart_reg
301 * To set the Control register by calling usb_fill_control_urb function
302 * by passing usb_rcvctrlpipe function as parameter.
303 */
304static int mos7840_get_uart_reg(struct usb_serial_port *port, __u16 reg,
305 __u16 *val)
306{
307 struct usb_device *dev = port->serial->dev;
308 int ret = 0;
309 __u16 Wval;
310 u8 *buf;
311
312 buf = kmalloc(VENDOR_READ_LENGTH, GFP_KERNEL);
313 if (!buf)
314 return -ENOMEM;
315
316 /* Wval is same as application number */
317 if (port->serial->num_ports == 2 && port->port_number != 0)
318 Wval = ((__u16)port->port_number + 2) << 8;
319 else
320 Wval = ((__u16)port->port_number + 1) << 8;
321 dev_dbg(&port->dev, "%s application number is %x\n", __func__, Wval);
322 ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), MCS_RDREQ,
323 MCS_RD_RTYPE, Wval, reg, buf, VENDOR_READ_LENGTH,
324 MOS_WDR_TIMEOUT);
325 if (ret < VENDOR_READ_LENGTH) {
326 if (ret >= 0)
327 ret = -EIO;
328 goto out;
329 }
330 *val = buf[0];
331out:
332 kfree(buf);
333 return ret;
334}
335
336static void mos7840_dump_serial_port(struct usb_serial_port *port,
337 struct moschip_port *mos7840_port)
338{
339
340 dev_dbg(&port->dev, "SpRegOffset is %2x\n", mos7840_port->SpRegOffset);
341 dev_dbg(&port->dev, "ControlRegOffset is %2x\n", mos7840_port->ControlRegOffset);
342 dev_dbg(&port->dev, "DCRRegOffset is %2x\n", mos7840_port->DcrRegOffset);
343
344}
345
346/************************************************************************/
347/************************************************************************/
348/* U S B C A L L B A C K F U N C T I O N S */
349/* U S B C A L L B A C K F U N C T I O N S */
350/************************************************************************/
351/************************************************************************/
352
353static void mos7840_set_led_callback(struct urb *urb)
354{
355 switch (urb->status) {
356 case 0:
357 /* Success */
358 break;
359 case -ECONNRESET:
360 case -ENOENT:
361 case -ESHUTDOWN:
362 /* This urb is terminated, clean up */
363 dev_dbg(&urb->dev->dev, "%s - urb shutting down: %d\n",
364 __func__, urb->status);
365 break;
366 default:
367 dev_dbg(&urb->dev->dev, "%s - nonzero urb status: %d\n",
368 __func__, urb->status);
369 }
370}
371
372static void mos7840_set_led_async(struct moschip_port *mcs, __u16 wval,
373 __u16 reg)
374{
375 struct usb_device *dev = mcs->port->serial->dev;
376 struct usb_ctrlrequest *dr = mcs->led_dr;
377
378 dr->bRequestType = MCS_WR_RTYPE;
379 dr->bRequest = MCS_WRREQ;
380 dr->wValue = cpu_to_le16(wval);
381 dr->wIndex = cpu_to_le16(reg);
382 dr->wLength = cpu_to_le16(0);
383
384 usb_fill_control_urb(mcs->led_urb, dev, usb_sndctrlpipe(dev, 0),
385 (unsigned char *)dr, NULL, 0, mos7840_set_led_callback, NULL);
386
387 usb_submit_urb(mcs->led_urb, GFP_ATOMIC);
388}
389
390static void mos7840_set_led_sync(struct usb_serial_port *port, __u16 reg,
391 __u16 val)
392{
393 struct usb_device *dev = port->serial->dev;
394
395 usb_control_msg(dev, usb_sndctrlpipe(dev, 0), MCS_WRREQ, MCS_WR_RTYPE,
396 val, reg, NULL, 0, MOS_WDR_TIMEOUT);
397}
398
399static void mos7840_led_off(struct timer_list *t)
400{
401 struct moschip_port *mcs = from_timer(mcs, t, led_timer1);
402
403 /* Turn off LED */
404 mos7840_set_led_async(mcs, 0x0300, MODEM_CONTROL_REGISTER);
405 mod_timer(&mcs->led_timer2,
406 jiffies + msecs_to_jiffies(LED_OFF_MS));
407}
408
409static void mos7840_led_flag_off(struct timer_list *t)
410{
411 struct moschip_port *mcs = from_timer(mcs, t, led_timer2);
412
413 clear_bit_unlock(MOS7840_FLAG_LED_BUSY, &mcs->flags);
414}
415
416static void mos7840_led_activity(struct usb_serial_port *port)
417{
418 struct moschip_port *mos7840_port = usb_get_serial_port_data(port);
419
420 if (test_and_set_bit_lock(MOS7840_FLAG_LED_BUSY, &mos7840_port->flags))
421 return;
422
423 mos7840_set_led_async(mos7840_port, 0x0301, MODEM_CONTROL_REGISTER);
424 mod_timer(&mos7840_port->led_timer1,
425 jiffies + msecs_to_jiffies(LED_ON_MS));
426}
427
428/*****************************************************************************
429 * mos7840_bulk_in_callback
430 * this is the callback function for when we have received data on the
431 * bulk in endpoint.
432 *****************************************************************************/
433
434static void mos7840_bulk_in_callback(struct urb *urb)
435{
436 struct moschip_port *mos7840_port = urb->context;
437 struct usb_serial_port *port = mos7840_port->port;
438 int retval;
439 unsigned char *data;
440 int status = urb->status;
441
442 if (status) {
443 dev_dbg(&urb->dev->dev, "nonzero read bulk status received: %d\n", status);
444 mos7840_port->read_urb_busy = false;
445 return;
446 }
447
448 data = urb->transfer_buffer;
449 usb_serial_debug_data(&port->dev, __func__, urb->actual_length, data);
450
451 if (urb->actual_length) {
452 struct tty_port *tport = &mos7840_port->port->port;
453 tty_insert_flip_string(tport, data, urb->actual_length);
454 tty_flip_buffer_push(tport);
455 port->icount.rx += urb->actual_length;
456 dev_dbg(&port->dev, "icount.rx is %d:\n", port->icount.rx);
457 }
458
459 if (mos7840_port->has_led)
460 mos7840_led_activity(port);
461
462 mos7840_port->read_urb_busy = true;
463 retval = usb_submit_urb(mos7840_port->read_urb, GFP_ATOMIC);
464
465 if (retval) {
466 dev_dbg(&port->dev, "usb_submit_urb(read bulk) failed, retval = %d\n", retval);
467 mos7840_port->read_urb_busy = false;
468 }
469}
470
471/*****************************************************************************
472 * mos7840_bulk_out_data_callback
473 * this is the callback function for when we have finished sending
474 * serial data on the bulk out endpoint.
475 *****************************************************************************/
476
477static void mos7840_bulk_out_data_callback(struct urb *urb)
478{
479 struct moschip_port *mos7840_port = urb->context;
480 struct usb_serial_port *port = mos7840_port->port;
481 int status = urb->status;
482 unsigned long flags;
483 int i;
484
485 spin_lock_irqsave(&mos7840_port->pool_lock, flags);
486 for (i = 0; i < NUM_URBS; i++) {
487 if (urb == mos7840_port->write_urb_pool[i]) {
488 mos7840_port->busy[i] = 0;
489 break;
490 }
491 }
492 spin_unlock_irqrestore(&mos7840_port->pool_lock, flags);
493
494 if (status) {
495 dev_dbg(&port->dev, "nonzero write bulk status received:%d\n", status);
496 return;
497 }
498
499 tty_port_tty_wakeup(&port->port);
500
501}
502
503/************************************************************************/
504/* D R I V E R T T Y I N T E R F A C E F U N C T I O N S */
505/************************************************************************/
506
507/*****************************************************************************
508 * mos7840_open
509 * this function is called by the tty driver when a port is opened
510 * If successful, we return 0
511 * Otherwise we return a negative error number.
512 *****************************************************************************/
513
514static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port)
515{
516 struct moschip_port *mos7840_port = usb_get_serial_port_data(port);
517 struct usb_serial *serial = port->serial;
518 int response;
519 int j;
520 struct urb *urb;
521 __u16 Data;
522 int status;
523
524 usb_clear_halt(serial->dev, port->write_urb->pipe);
525 usb_clear_halt(serial->dev, port->read_urb->pipe);
526
527 /* Initialising the write urb pool */
528 for (j = 0; j < NUM_URBS; ++j) {
529 urb = usb_alloc_urb(0, GFP_KERNEL);
530 mos7840_port->write_urb_pool[j] = urb;
531 if (!urb)
532 continue;
533
534 urb->transfer_buffer = kmalloc(URB_TRANSFER_BUFFER_SIZE,
535 GFP_KERNEL);
536 if (!urb->transfer_buffer) {
537 usb_free_urb(urb);
538 mos7840_port->write_urb_pool[j] = NULL;
539 continue;
540 }
541 }
542
543/*****************************************************************************
544 * Initialize MCS7840 -- Write Init values to corresponding Registers
545 *
546 * Register Index
547 * 1 : IER
548 * 2 : FCR
549 * 3 : LCR
550 * 4 : MCR
551 *
552 * 0x08 : SP1/2 Control Reg
553 *****************************************************************************/
554
555 /* NEED to check the following Block */
556
557 Data = 0x0;
558 status = mos7840_get_reg_sync(port, mos7840_port->SpRegOffset, &Data);
559 if (status < 0) {
560 dev_dbg(&port->dev, "Reading Spreg failed\n");
561 goto err;
562 }
563 Data |= 0x80;
564 status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data);
565 if (status < 0) {
566 dev_dbg(&port->dev, "writing Spreg failed\n");
567 goto err;
568 }
569
570 Data &= ~0x80;
571 status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data);
572 if (status < 0) {
573 dev_dbg(&port->dev, "writing Spreg failed\n");
574 goto err;
575 }
576 /* End of block to be checked */
577
578 Data = 0x0;
579 status = mos7840_get_reg_sync(port, mos7840_port->ControlRegOffset,
580 &Data);
581 if (status < 0) {
582 dev_dbg(&port->dev, "Reading Controlreg failed\n");
583 goto err;
584 }
585 Data |= 0x08; /* Driver done bit */
586 Data |= 0x20; /* rx_disable */
587 status = mos7840_set_reg_sync(port,
588 mos7840_port->ControlRegOffset, Data);
589 if (status < 0) {
590 dev_dbg(&port->dev, "writing Controlreg failed\n");
591 goto err;
592 }
593 /* do register settings here */
594 /* Set all regs to the device default values. */
595 /***********************************
596 * First Disable all interrupts.
597 ***********************************/
598 Data = 0x00;
599 status = mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
600 if (status < 0) {
601 dev_dbg(&port->dev, "disabling interrupts failed\n");
602 goto err;
603 }
604 /* Set FIFO_CONTROL_REGISTER to the default value */
605 Data = 0x00;
606 status = mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
607 if (status < 0) {
608 dev_dbg(&port->dev, "Writing FIFO_CONTROL_REGISTER failed\n");
609 goto err;
610 }
611
612 Data = 0xcf;
613 status = mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
614 if (status < 0) {
615 dev_dbg(&port->dev, "Writing FIFO_CONTROL_REGISTER failed\n");
616 goto err;
617 }
618
619 Data = 0x03;
620 status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
621 mos7840_port->shadowLCR = Data;
622
623 Data = 0x0b;
624 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
625 mos7840_port->shadowMCR = Data;
626
627 Data = 0x00;
628 status = mos7840_get_uart_reg(port, LINE_CONTROL_REGISTER, &Data);
629 mos7840_port->shadowLCR = Data;
630
631 Data |= SERIAL_LCR_DLAB; /* data latch enable in LCR 0x80 */
632 status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
633
634 Data = 0x0c;
635 status = mos7840_set_uart_reg(port, DIVISOR_LATCH_LSB, Data);
636
637 Data = 0x0;
638 status = mos7840_set_uart_reg(port, DIVISOR_LATCH_MSB, Data);
639
640 Data = 0x00;
641 status = mos7840_get_uart_reg(port, LINE_CONTROL_REGISTER, &Data);
642
643 Data = Data & ~SERIAL_LCR_DLAB;
644 status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
645 mos7840_port->shadowLCR = Data;
646
647 /* clearing Bulkin and Bulkout Fifo */
648 Data = 0x0;
649 status = mos7840_get_reg_sync(port, mos7840_port->SpRegOffset, &Data);
650
651 Data = Data | 0x0c;
652 status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data);
653
654 Data = Data & ~0x0c;
655 status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data);
656 /* Finally enable all interrupts */
657 Data = 0x0c;
658 status = mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
659
660 /* clearing rx_disable */
661 Data = 0x0;
662 status = mos7840_get_reg_sync(port, mos7840_port->ControlRegOffset,
663 &Data);
664 Data = Data & ~0x20;
665 status = mos7840_set_reg_sync(port, mos7840_port->ControlRegOffset,
666 Data);
667
668 /* rx_negate */
669 Data = 0x0;
670 status = mos7840_get_reg_sync(port, mos7840_port->ControlRegOffset,
671 &Data);
672 Data = Data | 0x10;
673 status = mos7840_set_reg_sync(port, mos7840_port->ControlRegOffset,
674 Data);
675
676 dev_dbg(&port->dev, "port number is %d\n", port->port_number);
677 dev_dbg(&port->dev, "minor number is %d\n", port->minor);
678 dev_dbg(&port->dev, "Bulkin endpoint is %d\n", port->bulk_in_endpointAddress);
679 dev_dbg(&port->dev, "BulkOut endpoint is %d\n", port->bulk_out_endpointAddress);
680 dev_dbg(&port->dev, "Interrupt endpoint is %d\n", port->interrupt_in_endpointAddress);
681 dev_dbg(&port->dev, "port's number in the device is %d\n", mos7840_port->port_num);
682 mos7840_port->read_urb = port->read_urb;
683
684 /* set up our bulk in urb */
685 if ((serial->num_ports == 2) && (((__u16)port->port_number % 2) != 0)) {
686 usb_fill_bulk_urb(mos7840_port->read_urb,
687 serial->dev,
688 usb_rcvbulkpipe(serial->dev,
689 (port->bulk_in_endpointAddress) + 2),
690 port->bulk_in_buffer,
691 mos7840_port->read_urb->transfer_buffer_length,
692 mos7840_bulk_in_callback, mos7840_port);
693 } else {
694 usb_fill_bulk_urb(mos7840_port->read_urb,
695 serial->dev,
696 usb_rcvbulkpipe(serial->dev,
697 port->bulk_in_endpointAddress),
698 port->bulk_in_buffer,
699 mos7840_port->read_urb->transfer_buffer_length,
700 mos7840_bulk_in_callback, mos7840_port);
701 }
702
703 dev_dbg(&port->dev, "%s: bulkin endpoint is %d\n", __func__, port->bulk_in_endpointAddress);
704 mos7840_port->read_urb_busy = true;
705 response = usb_submit_urb(mos7840_port->read_urb, GFP_KERNEL);
706 if (response) {
707 dev_err(&port->dev, "%s - Error %d submitting control urb\n",
708 __func__, response);
709 mos7840_port->read_urb_busy = false;
710 }
711
712 /* initialize our port settings */
713 /* Must set to enable ints! */
714 mos7840_port->shadowMCR = MCR_MASTER_IE;
715
716 return 0;
717err:
718 for (j = 0; j < NUM_URBS; ++j) {
719 urb = mos7840_port->write_urb_pool[j];
720 if (!urb)
721 continue;
722 kfree(urb->transfer_buffer);
723 usb_free_urb(urb);
724 }
725 return status;
726}
727
728/*****************************************************************************
729 * mos7840_chars_in_buffer
730 * this function is called by the tty driver when it wants to know how many
731 * bytes of data we currently have outstanding in the port (data that has
732 * been written, but hasn't made it out the port yet)
733 * If successful, we return the number of bytes left to be written in the
734 * system,
735 * Otherwise we return zero.
736 *****************************************************************************/
737
738static int mos7840_chars_in_buffer(struct tty_struct *tty)
739{
740 struct usb_serial_port *port = tty->driver_data;
741 struct moschip_port *mos7840_port = usb_get_serial_port_data(port);
742 int i;
743 int chars = 0;
744 unsigned long flags;
745
746 spin_lock_irqsave(&mos7840_port->pool_lock, flags);
747 for (i = 0; i < NUM_URBS; ++i) {
748 if (mos7840_port->busy[i]) {
749 struct urb *urb = mos7840_port->write_urb_pool[i];
750 chars += urb->transfer_buffer_length;
751 }
752 }
753 spin_unlock_irqrestore(&mos7840_port->pool_lock, flags);
754 dev_dbg(&port->dev, "%s - returns %d\n", __func__, chars);
755 return chars;
756
757}
758
759/*****************************************************************************
760 * mos7840_close
761 * this function is called by the tty driver when a port is closed
762 *****************************************************************************/
763
764static void mos7840_close(struct usb_serial_port *port)
765{
766 struct moschip_port *mos7840_port = usb_get_serial_port_data(port);
767 int j;
768 __u16 Data;
769
770 for (j = 0; j < NUM_URBS; ++j)
771 usb_kill_urb(mos7840_port->write_urb_pool[j]);
772
773 /* Freeing Write URBs */
774 for (j = 0; j < NUM_URBS; ++j) {
775 if (mos7840_port->write_urb_pool[j]) {
776 kfree(mos7840_port->write_urb_pool[j]->transfer_buffer);
777 usb_free_urb(mos7840_port->write_urb_pool[j]);
778 }
779 }
780
781 usb_kill_urb(mos7840_port->read_urb);
782 mos7840_port->read_urb_busy = false;
783
784 Data = 0x0;
785 mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
786
787 Data = 0x00;
788 mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
789}
790
791/*****************************************************************************
792 * mos7840_break
793 * this function sends a break to the port
794 *****************************************************************************/
795static void mos7840_break(struct tty_struct *tty, int break_state)
796{
797 struct usb_serial_port *port = tty->driver_data;
798 struct moschip_port *mos7840_port = usb_get_serial_port_data(port);
799 unsigned char data;
800
801 if (break_state == -1)
802 data = mos7840_port->shadowLCR | LCR_SET_BREAK;
803 else
804 data = mos7840_port->shadowLCR & ~LCR_SET_BREAK;
805
806 /* FIXME: no locking on shadowLCR anywhere in driver */
807 mos7840_port->shadowLCR = data;
808 dev_dbg(&port->dev, "%s mos7840_port->shadowLCR is %x\n", __func__, mos7840_port->shadowLCR);
809 mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER,
810 mos7840_port->shadowLCR);
811}
812
813/*****************************************************************************
814 * mos7840_write_room
815 * this function is called by the tty driver when it wants to know how many
816 * bytes of data we can accept for a specific port.
817 * If successful, we return the amount of room that we have for this port
818 * Otherwise we return a negative error number.
819 *****************************************************************************/
820
821static int mos7840_write_room(struct tty_struct *tty)
822{
823 struct usb_serial_port *port = tty->driver_data;
824 struct moschip_port *mos7840_port = usb_get_serial_port_data(port);
825 int i;
826 int room = 0;
827 unsigned long flags;
828
829 spin_lock_irqsave(&mos7840_port->pool_lock, flags);
830 for (i = 0; i < NUM_URBS; ++i) {
831 if (!mos7840_port->busy[i])
832 room += URB_TRANSFER_BUFFER_SIZE;
833 }
834 spin_unlock_irqrestore(&mos7840_port->pool_lock, flags);
835
836 room = (room == 0) ? 0 : room - URB_TRANSFER_BUFFER_SIZE + 1;
837 dev_dbg(&mos7840_port->port->dev, "%s - returns %d\n", __func__, room);
838 return room;
839
840}
841
842/*****************************************************************************
843 * mos7840_write
844 * this function is called by the tty driver when data should be written to
845 * the port.
846 * If successful, we return the number of bytes written, otherwise we
847 * return a negative error number.
848 *****************************************************************************/
849
850static int mos7840_write(struct tty_struct *tty, struct usb_serial_port *port,
851 const unsigned char *data, int count)
852{
853 struct moschip_port *mos7840_port = usb_get_serial_port_data(port);
854 struct usb_serial *serial = port->serial;
855 int status;
856 int i;
857 int bytes_sent = 0;
858 int transfer_size;
859 unsigned long flags;
860 struct urb *urb;
861 /* __u16 Data; */
862 const unsigned char *current_position = data;
863
864 /* try to find a free urb in the list */
865 urb = NULL;
866
867 spin_lock_irqsave(&mos7840_port->pool_lock, flags);
868 for (i = 0; i < NUM_URBS; ++i) {
869 if (!mos7840_port->busy[i]) {
870 mos7840_port->busy[i] = 1;
871 urb = mos7840_port->write_urb_pool[i];
872 dev_dbg(&port->dev, "URB:%d\n", i);
873 break;
874 }
875 }
876 spin_unlock_irqrestore(&mos7840_port->pool_lock, flags);
877
878 if (urb == NULL) {
879 dev_dbg(&port->dev, "%s - no more free urbs\n", __func__);
880 goto exit;
881 }
882
883 if (urb->transfer_buffer == NULL) {
884 urb->transfer_buffer = kmalloc(URB_TRANSFER_BUFFER_SIZE,
885 GFP_ATOMIC);
886 if (!urb->transfer_buffer)
887 goto exit;
888 }
889 transfer_size = min(count, URB_TRANSFER_BUFFER_SIZE);
890
891 memcpy(urb->transfer_buffer, current_position, transfer_size);
892
893 /* fill urb with data and submit */
894 if ((serial->num_ports == 2) && (((__u16)port->port_number % 2) != 0)) {
895 usb_fill_bulk_urb(urb,
896 serial->dev,
897 usb_sndbulkpipe(serial->dev,
898 (port->bulk_out_endpointAddress) + 2),
899 urb->transfer_buffer,
900 transfer_size,
901 mos7840_bulk_out_data_callback, mos7840_port);
902 } else {
903 usb_fill_bulk_urb(urb,
904 serial->dev,
905 usb_sndbulkpipe(serial->dev,
906 port->bulk_out_endpointAddress),
907 urb->transfer_buffer,
908 transfer_size,
909 mos7840_bulk_out_data_callback, mos7840_port);
910 }
911
912 dev_dbg(&port->dev, "bulkout endpoint is %d\n", port->bulk_out_endpointAddress);
913
914 if (mos7840_port->has_led)
915 mos7840_led_activity(port);
916
917 /* send it down the pipe */
918 status = usb_submit_urb(urb, GFP_ATOMIC);
919
920 if (status) {
921 mos7840_port->busy[i] = 0;
922 dev_err_console(port, "%s - usb_submit_urb(write bulk) failed "
923 "with status = %d\n", __func__, status);
924 bytes_sent = status;
925 goto exit;
926 }
927 bytes_sent = transfer_size;
928 port->icount.tx += transfer_size;
929 dev_dbg(&port->dev, "icount.tx is %d:\n", port->icount.tx);
930exit:
931 return bytes_sent;
932
933}
934
935/*****************************************************************************
936 * mos7840_throttle
937 * this function is called by the tty driver when it wants to stop the data
938 * being read from the port.
939 *****************************************************************************/
940
941static void mos7840_throttle(struct tty_struct *tty)
942{
943 struct usb_serial_port *port = tty->driver_data;
944 struct moschip_port *mos7840_port = usb_get_serial_port_data(port);
945 int status;
946
947 /* if we are implementing XON/XOFF, send the stop character */
948 if (I_IXOFF(tty)) {
949 unsigned char stop_char = STOP_CHAR(tty);
950 status = mos7840_write(tty, port, &stop_char, 1);
951 if (status <= 0)
952 return;
953 }
954 /* if we are implementing RTS/CTS, toggle that line */
955 if (C_CRTSCTS(tty)) {
956 mos7840_port->shadowMCR &= ~MCR_RTS;
957 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
958 mos7840_port->shadowMCR);
959 if (status < 0)
960 return;
961 }
962}
963
964/*****************************************************************************
965 * mos7840_unthrottle
966 * this function is called by the tty driver when it wants to resume
967 * the data being read from the port (called after mos7840_throttle is
968 * called)
969 *****************************************************************************/
970static void mos7840_unthrottle(struct tty_struct *tty)
971{
972 struct usb_serial_port *port = tty->driver_data;
973 struct moschip_port *mos7840_port = usb_get_serial_port_data(port);
974 int status;
975
976 /* if we are implementing XON/XOFF, send the start character */
977 if (I_IXOFF(tty)) {
978 unsigned char start_char = START_CHAR(tty);
979 status = mos7840_write(tty, port, &start_char, 1);
980 if (status <= 0)
981 return;
982 }
983
984 /* if we are implementing RTS/CTS, toggle that line */
985 if (C_CRTSCTS(tty)) {
986 mos7840_port->shadowMCR |= MCR_RTS;
987 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
988 mos7840_port->shadowMCR);
989 if (status < 0)
990 return;
991 }
992}
993
994static int mos7840_tiocmget(struct tty_struct *tty)
995{
996 struct usb_serial_port *port = tty->driver_data;
997 unsigned int result;
998 __u16 msr;
999 __u16 mcr;
1000 int status;
1001
1002 status = mos7840_get_uart_reg(port, MODEM_STATUS_REGISTER, &msr);
1003 if (status < 0)
1004 return -EIO;
1005 status = mos7840_get_uart_reg(port, MODEM_CONTROL_REGISTER, &mcr);
1006 if (status < 0)
1007 return -EIO;
1008 result = ((mcr & MCR_DTR) ? TIOCM_DTR : 0)
1009 | ((mcr & MCR_RTS) ? TIOCM_RTS : 0)
1010 | ((mcr & MCR_LOOPBACK) ? TIOCM_LOOP : 0)
1011 | ((msr & MOS7840_MSR_CTS) ? TIOCM_CTS : 0)
1012 | ((msr & MOS7840_MSR_CD) ? TIOCM_CAR : 0)
1013 | ((msr & MOS7840_MSR_RI) ? TIOCM_RI : 0)
1014 | ((msr & MOS7840_MSR_DSR) ? TIOCM_DSR : 0);
1015
1016 dev_dbg(&port->dev, "%s - 0x%04X\n", __func__, result);
1017
1018 return result;
1019}
1020
1021static int mos7840_tiocmset(struct tty_struct *tty,
1022 unsigned int set, unsigned int clear)
1023{
1024 struct usb_serial_port *port = tty->driver_data;
1025 struct moschip_port *mos7840_port = usb_get_serial_port_data(port);
1026 unsigned int mcr;
1027 int status;
1028
1029 /* FIXME: What locks the port registers ? */
1030 mcr = mos7840_port->shadowMCR;
1031 if (clear & TIOCM_RTS)
1032 mcr &= ~MCR_RTS;
1033 if (clear & TIOCM_DTR)
1034 mcr &= ~MCR_DTR;
1035 if (clear & TIOCM_LOOP)
1036 mcr &= ~MCR_LOOPBACK;
1037
1038 if (set & TIOCM_RTS)
1039 mcr |= MCR_RTS;
1040 if (set & TIOCM_DTR)
1041 mcr |= MCR_DTR;
1042 if (set & TIOCM_LOOP)
1043 mcr |= MCR_LOOPBACK;
1044
1045 mos7840_port->shadowMCR = mcr;
1046
1047 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, mcr);
1048 if (status < 0) {
1049 dev_dbg(&port->dev, "setting MODEM_CONTROL_REGISTER Failed\n");
1050 return status;
1051 }
1052
1053 return 0;
1054}
1055
1056/*****************************************************************************
1057 * mos7840_calc_baud_rate_divisor
1058 * this function calculates the proper baud rate divisor for the specified
1059 * baud rate.
1060 *****************************************************************************/
1061static int mos7840_calc_baud_rate_divisor(struct usb_serial_port *port,
1062 int baudRate, int *divisor,
1063 __u16 *clk_sel_val)
1064{
1065 dev_dbg(&port->dev, "%s - %d\n", __func__, baudRate);
1066
1067 if (baudRate <= 115200) {
1068 *divisor = 115200 / baudRate;
1069 *clk_sel_val = 0x0;
1070 }
1071 if ((baudRate > 115200) && (baudRate <= 230400)) {
1072 *divisor = 230400 / baudRate;
1073 *clk_sel_val = 0x10;
1074 } else if ((baudRate > 230400) && (baudRate <= 403200)) {
1075 *divisor = 403200 / baudRate;
1076 *clk_sel_val = 0x20;
1077 } else if ((baudRate > 403200) && (baudRate <= 460800)) {
1078 *divisor = 460800 / baudRate;
1079 *clk_sel_val = 0x30;
1080 } else if ((baudRate > 460800) && (baudRate <= 806400)) {
1081 *divisor = 806400 / baudRate;
1082 *clk_sel_val = 0x40;
1083 } else if ((baudRate > 806400) && (baudRate <= 921600)) {
1084 *divisor = 921600 / baudRate;
1085 *clk_sel_val = 0x50;
1086 } else if ((baudRate > 921600) && (baudRate <= 1572864)) {
1087 *divisor = 1572864 / baudRate;
1088 *clk_sel_val = 0x60;
1089 } else if ((baudRate > 1572864) && (baudRate <= 3145728)) {
1090 *divisor = 3145728 / baudRate;
1091 *clk_sel_val = 0x70;
1092 }
1093 return 0;
1094}
1095
1096/*****************************************************************************
1097 * mos7840_send_cmd_write_baud_rate
1098 * this function sends the proper command to change the baud rate of the
1099 * specified port.
1100 *****************************************************************************/
1101
1102static int mos7840_send_cmd_write_baud_rate(struct moschip_port *mos7840_port,
1103 int baudRate)
1104{
1105 struct usb_serial_port *port = mos7840_port->port;
1106 int divisor = 0;
1107 int status;
1108 __u16 Data;
1109 __u16 clk_sel_val;
1110
1111 dev_dbg(&port->dev, "%s - baud = %d\n", __func__, baudRate);
1112 /* reset clk_uart_sel in spregOffset */
1113 if (baudRate > 115200) {
1114#ifdef HW_flow_control
1115 /* NOTE: need to see the pther register to modify */
1116 /* setting h/w flow control bit to 1 */
1117 Data = 0x2b;
1118 mos7840_port->shadowMCR = Data;
1119 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
1120 Data);
1121 if (status < 0) {
1122 dev_dbg(&port->dev, "Writing spreg failed in set_serial_baud\n");
1123 return -1;
1124 }
1125#endif
1126
1127 } else {
1128#ifdef HW_flow_control
1129 /* setting h/w flow control bit to 0 */
1130 Data = 0xb;
1131 mos7840_port->shadowMCR = Data;
1132 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
1133 Data);
1134 if (status < 0) {
1135 dev_dbg(&port->dev, "Writing spreg failed in set_serial_baud\n");
1136 return -1;
1137 }
1138#endif
1139
1140 }
1141
1142 if (1) { /* baudRate <= 115200) */
1143 clk_sel_val = 0x0;
1144 Data = 0x0;
1145 status = mos7840_calc_baud_rate_divisor(port, baudRate, &divisor,
1146 &clk_sel_val);
1147 status = mos7840_get_reg_sync(port, mos7840_port->SpRegOffset,
1148 &Data);
1149 if (status < 0) {
1150 dev_dbg(&port->dev, "reading spreg failed in set_serial_baud\n");
1151 return -1;
1152 }
1153 Data = (Data & 0x8f) | clk_sel_val;
1154 status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset,
1155 Data);
1156 if (status < 0) {
1157 dev_dbg(&port->dev, "Writing spreg failed in set_serial_baud\n");
1158 return -1;
1159 }
1160 /* Calculate the Divisor */
1161
1162 if (status) {
1163 dev_err(&port->dev, "%s - bad baud rate\n", __func__);
1164 return status;
1165 }
1166 /* Enable access to divisor latch */
1167 Data = mos7840_port->shadowLCR | SERIAL_LCR_DLAB;
1168 mos7840_port->shadowLCR = Data;
1169 mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
1170
1171 /* Write the divisor */
1172 Data = (unsigned char)(divisor & 0xff);
1173 dev_dbg(&port->dev, "set_serial_baud Value to write DLL is %x\n", Data);
1174 mos7840_set_uart_reg(port, DIVISOR_LATCH_LSB, Data);
1175
1176 Data = (unsigned char)((divisor & 0xff00) >> 8);
1177 dev_dbg(&port->dev, "set_serial_baud Value to write DLM is %x\n", Data);
1178 mos7840_set_uart_reg(port, DIVISOR_LATCH_MSB, Data);
1179
1180 /* Disable access to divisor latch */
1181 Data = mos7840_port->shadowLCR & ~SERIAL_LCR_DLAB;
1182 mos7840_port->shadowLCR = Data;
1183 mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
1184
1185 }
1186 return status;
1187}
1188
1189/*****************************************************************************
1190 * mos7840_change_port_settings
1191 * This routine is called to set the UART on the device to match
1192 * the specified new settings.
1193 *****************************************************************************/
1194
1195static void mos7840_change_port_settings(struct tty_struct *tty,
1196 struct moschip_port *mos7840_port, struct ktermios *old_termios)
1197{
1198 struct usb_serial_port *port = mos7840_port->port;
1199 int baud;
1200 unsigned cflag;
1201 __u8 lData;
1202 __u8 lParity;
1203 __u8 lStop;
1204 int status;
1205 __u16 Data;
1206
1207 lData = LCR_BITS_8;
1208 lStop = LCR_STOP_1;
1209 lParity = LCR_PAR_NONE;
1210
1211 cflag = tty->termios.c_cflag;
1212
1213 /* Change the number of bits */
1214 switch (cflag & CSIZE) {
1215 case CS5:
1216 lData = LCR_BITS_5;
1217 break;
1218
1219 case CS6:
1220 lData = LCR_BITS_6;
1221 break;
1222
1223 case CS7:
1224 lData = LCR_BITS_7;
1225 break;
1226
1227 default:
1228 case CS8:
1229 lData = LCR_BITS_8;
1230 break;
1231 }
1232
1233 /* Change the Parity bit */
1234 if (cflag & PARENB) {
1235 if (cflag & PARODD) {
1236 lParity = LCR_PAR_ODD;
1237 dev_dbg(&port->dev, "%s - parity = odd\n", __func__);
1238 } else {
1239 lParity = LCR_PAR_EVEN;
1240 dev_dbg(&port->dev, "%s - parity = even\n", __func__);
1241 }
1242
1243 } else {
1244 dev_dbg(&port->dev, "%s - parity = none\n", __func__);
1245 }
1246
1247 if (cflag & CMSPAR)
1248 lParity = lParity | 0x20;
1249
1250 /* Change the Stop bit */
1251 if (cflag & CSTOPB) {
1252 lStop = LCR_STOP_2;
1253 dev_dbg(&port->dev, "%s - stop bits = 2\n", __func__);
1254 } else {
1255 lStop = LCR_STOP_1;
1256 dev_dbg(&port->dev, "%s - stop bits = 1\n", __func__);
1257 }
1258
1259 /* Update the LCR with the correct value */
1260 mos7840_port->shadowLCR &=
1261 ~(LCR_BITS_MASK | LCR_STOP_MASK | LCR_PAR_MASK);
1262 mos7840_port->shadowLCR |= (lData | lParity | lStop);
1263
1264 dev_dbg(&port->dev, "%s - mos7840_port->shadowLCR is %x\n", __func__,
1265 mos7840_port->shadowLCR);
1266 /* Disable Interrupts */
1267 Data = 0x00;
1268 mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
1269
1270 Data = 0x00;
1271 mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
1272
1273 Data = 0xcf;
1274 mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
1275
1276 /* Send the updated LCR value to the mos7840 */
1277 Data = mos7840_port->shadowLCR;
1278
1279 mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
1280
1281 Data = 0x00b;
1282 mos7840_port->shadowMCR = Data;
1283 mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
1284 Data = 0x00b;
1285 mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
1286
1287 /* set up the MCR register and send it to the mos7840 */
1288
1289 mos7840_port->shadowMCR = MCR_MASTER_IE;
1290 if (cflag & CBAUD)
1291 mos7840_port->shadowMCR |= (MCR_DTR | MCR_RTS);
1292
1293 if (cflag & CRTSCTS)
1294 mos7840_port->shadowMCR |= (MCR_XON_ANY);
1295 else
1296 mos7840_port->shadowMCR &= ~(MCR_XON_ANY);
1297
1298 Data = mos7840_port->shadowMCR;
1299 mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
1300
1301 /* Determine divisor based on baud rate */
1302 baud = tty_get_baud_rate(tty);
1303
1304 if (!baud) {
1305 /* pick a default, any default... */
1306 dev_dbg(&port->dev, "%s", "Picked default baud...\n");
1307 baud = 9600;
1308 }
1309
1310 dev_dbg(&port->dev, "%s - baud rate = %d\n", __func__, baud);
1311 status = mos7840_send_cmd_write_baud_rate(mos7840_port, baud);
1312
1313 /* Enable Interrupts */
1314 Data = 0x0c;
1315 mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
1316
1317 if (!mos7840_port->read_urb_busy) {
1318 mos7840_port->read_urb_busy = true;
1319 status = usb_submit_urb(mos7840_port->read_urb, GFP_KERNEL);
1320 if (status) {
1321 dev_dbg(&port->dev, "usb_submit_urb(read bulk) failed, status = %d\n",
1322 status);
1323 mos7840_port->read_urb_busy = false;
1324 }
1325 }
1326 dev_dbg(&port->dev, "%s - mos7840_port->shadowLCR is End %x\n", __func__,
1327 mos7840_port->shadowLCR);
1328}
1329
1330/*****************************************************************************
1331 * mos7840_set_termios
1332 * this function is called by the tty driver when it wants to change
1333 * the termios structure
1334 *****************************************************************************/
1335
1336static void mos7840_set_termios(struct tty_struct *tty,
1337 struct usb_serial_port *port,
1338 struct ktermios *old_termios)
1339{
1340 struct moschip_port *mos7840_port = usb_get_serial_port_data(port);
1341 int status;
1342
1343 /* change the port settings to the new ones specified */
1344
1345 mos7840_change_port_settings(tty, mos7840_port, old_termios);
1346
1347 if (!mos7840_port->read_urb_busy) {
1348 mos7840_port->read_urb_busy = true;
1349 status = usb_submit_urb(mos7840_port->read_urb, GFP_KERNEL);
1350 if (status) {
1351 dev_dbg(&port->dev, "usb_submit_urb(read bulk) failed, status = %d\n",
1352 status);
1353 mos7840_port->read_urb_busy = false;
1354 }
1355 }
1356}
1357
1358/*****************************************************************************
1359 * mos7840_get_lsr_info - get line status register info
1360 *
1361 * Purpose: Let user call ioctl() to get info when the UART physically
1362 * is emptied. On bus types like RS485, the transmitter must
1363 * release the bus after transmitting. This must be done when
1364 * the transmit shift register is empty, not be done when the
1365 * transmit holding register is empty. This functionality
1366 * allows an RS485 driver to be written in user space.
1367 *****************************************************************************/
1368
1369static int mos7840_get_lsr_info(struct tty_struct *tty,
1370 unsigned int __user *value)
1371{
1372 int count;
1373 unsigned int result = 0;
1374
1375 count = mos7840_chars_in_buffer(tty);
1376 if (count == 0)
1377 result = TIOCSER_TEMT;
1378
1379 if (copy_to_user(value, &result, sizeof(int)))
1380 return -EFAULT;
1381 return 0;
1382}
1383
1384/*****************************************************************************
1385 * mos7840_get_serial_info
1386 * function to get information about serial port
1387 *****************************************************************************/
1388
1389static int mos7840_get_serial_info(struct tty_struct *tty,
1390 struct serial_struct *ss)
1391{
1392 struct usb_serial_port *port = tty->driver_data;
1393 struct moschip_port *mos7840_port = usb_get_serial_port_data(port);
1394
1395 ss->type = PORT_16550A;
1396 ss->line = mos7840_port->port->minor;
1397 ss->port = mos7840_port->port->port_number;
1398 ss->irq = 0;
1399 ss->xmit_fifo_size = NUM_URBS * URB_TRANSFER_BUFFER_SIZE;
1400 ss->baud_base = 9600;
1401 ss->close_delay = 5 * HZ;
1402 ss->closing_wait = 30 * HZ;
1403 return 0;
1404}
1405
1406/*****************************************************************************
1407 * SerialIoctl
1408 * this function handles any ioctl calls to the driver
1409 *****************************************************************************/
1410
1411static int mos7840_ioctl(struct tty_struct *tty,
1412 unsigned int cmd, unsigned long arg)
1413{
1414 struct usb_serial_port *port = tty->driver_data;
1415 void __user *argp = (void __user *)arg;
1416
1417 switch (cmd) {
1418 /* return number of bytes available */
1419
1420 case TIOCSERGETLSR:
1421 dev_dbg(&port->dev, "%s TIOCSERGETLSR\n", __func__);
1422 return mos7840_get_lsr_info(tty, argp);
1423
1424 default:
1425 break;
1426 }
1427 return -ENOIOCTLCMD;
1428}
1429
1430/*
1431 * Check if GPO (pin 42) is connected to GPI (pin 33) as recommended by ASIX
1432 * for MCS7810 by bit-banging a 16-bit word.
1433 *
1434 * Note that GPO is really RTS of the third port so this will toggle RTS of
1435 * port two or three on two- and four-port devices.
1436 */
1437static int mos7810_check(struct usb_serial *serial)
1438{
1439 int i, pass_count = 0;
1440 u8 *buf;
1441 __u16 data = 0, mcr_data = 0;
1442 __u16 test_pattern = 0x55AA;
1443 int res;
1444
1445 buf = kmalloc(VENDOR_READ_LENGTH, GFP_KERNEL);
1446 if (!buf)
1447 return 0; /* failed to identify 7810 */
1448
1449 /* Store MCR setting */
1450 res = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
1451 MCS_RDREQ, MCS_RD_RTYPE, 0x0300, MODEM_CONTROL_REGISTER,
1452 buf, VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT);
1453 if (res == VENDOR_READ_LENGTH)
1454 mcr_data = *buf;
1455
1456 for (i = 0; i < 16; i++) {
1457 /* Send the 1-bit test pattern out to MCS7810 test pin */
1458 usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
1459 MCS_WRREQ, MCS_WR_RTYPE,
1460 (0x0300 | (((test_pattern >> i) & 0x0001) << 1)),
1461 MODEM_CONTROL_REGISTER, NULL, 0, MOS_WDR_TIMEOUT);
1462
1463 /* Read the test pattern back */
1464 res = usb_control_msg(serial->dev,
1465 usb_rcvctrlpipe(serial->dev, 0), MCS_RDREQ,
1466 MCS_RD_RTYPE, 0, GPIO_REGISTER, buf,
1467 VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT);
1468 if (res == VENDOR_READ_LENGTH)
1469 data = *buf;
1470
1471 /* If this is a MCS7810 device, both test patterns must match */
1472 if (((test_pattern >> i) ^ (~data >> 1)) & 0x0001)
1473 break;
1474
1475 pass_count++;
1476 }
1477
1478 /* Restore MCR setting */
1479 usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), MCS_WRREQ,
1480 MCS_WR_RTYPE, 0x0300 | mcr_data, MODEM_CONTROL_REGISTER, NULL,
1481 0, MOS_WDR_TIMEOUT);
1482
1483 kfree(buf);
1484
1485 if (pass_count == 16)
1486 return 1;
1487
1488 return 0;
1489}
1490
1491static int mos7840_probe(struct usb_serial *serial,
1492 const struct usb_device_id *id)
1493{
1494 unsigned long device_flags = id->driver_info;
1495 u8 *buf;
1496
1497 /* Skip device-type detection if we already have device flags. */
1498 if (device_flags)
1499 goto out;
1500
1501 buf = kzalloc(VENDOR_READ_LENGTH, GFP_KERNEL);
1502 if (!buf)
1503 return -ENOMEM;
1504
1505 usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
1506 MCS_RDREQ, MCS_RD_RTYPE, 0, GPIO_REGISTER, buf,
1507 VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT);
1508
1509 /* For a MCS7840 device GPIO0 must be set to 1 */
1510 if (buf[0] & 0x01)
1511 device_flags = MCS_PORTS(4);
1512 else if (mos7810_check(serial))
1513 device_flags = MCS_PORTS(1) | MCS_LED;
1514 else
1515 device_flags = MCS_PORTS(2);
1516
1517 kfree(buf);
1518out:
1519 usb_set_serial_data(serial, (void *)device_flags);
1520
1521 return 0;
1522}
1523
1524static int mos7840_calc_num_ports(struct usb_serial *serial,
1525 struct usb_serial_endpoints *epds)
1526{
1527 unsigned long device_flags = (unsigned long)usb_get_serial_data(serial);
1528 int num_ports = MCS_PORTS(device_flags);
1529
1530 if (num_ports == 0 || num_ports > 4)
1531 return -ENODEV;
1532
1533 if (epds->num_bulk_in < num_ports || epds->num_bulk_out < num_ports) {
1534 dev_err(&serial->interface->dev, "missing endpoints\n");
1535 return -ENODEV;
1536 }
1537
1538 return num_ports;
1539}
1540
1541static int mos7840_attach(struct usb_serial *serial)
1542{
1543 struct device *dev = &serial->interface->dev;
1544 int status;
1545 u16 val;
1546
1547 /* Zero Length flag enable */
1548 val = 0x0f;
1549 status = mos7840_set_reg_sync(serial->port[0], ZLP_REG5, val);
1550 if (status < 0)
1551 dev_dbg(dev, "Writing ZLP_REG5 failed status-0x%x\n", status);
1552 else
1553 dev_dbg(dev, "ZLP_REG5 Writing success status%d\n", status);
1554
1555 return status;
1556}
1557
1558static int mos7840_port_probe(struct usb_serial_port *port)
1559{
1560 struct usb_serial *serial = port->serial;
1561 unsigned long device_flags = (unsigned long)usb_get_serial_data(serial);
1562 struct moschip_port *mos7840_port;
1563 int status;
1564 int pnum;
1565 __u16 Data;
1566
1567 /* we set up the pointers to the endpoints in the mos7840_open *
1568 * function, as the structures aren't created yet. */
1569
1570 pnum = port->port_number;
1571
1572 dev_dbg(&port->dev, "mos7840_startup: configuring port %d\n", pnum);
1573 mos7840_port = kzalloc(sizeof(struct moschip_port), GFP_KERNEL);
1574 if (!mos7840_port)
1575 return -ENOMEM;
1576
1577 /* Initialize all port interrupt end point to port 0 int
1578 * endpoint. Our device has only one interrupt end point
1579 * common to all port */
1580
1581 mos7840_port->port = port;
1582 spin_lock_init(&mos7840_port->pool_lock);
1583
1584 /* minor is not initialised until later by
1585 * usb-serial.c:get_free_serial() and cannot therefore be used
1586 * to index device instances */
1587 mos7840_port->port_num = pnum + 1;
1588 dev_dbg(&port->dev, "port->minor = %d\n", port->minor);
1589 dev_dbg(&port->dev, "mos7840_port->port_num = %d\n", mos7840_port->port_num);
1590
1591 if (mos7840_port->port_num == 1) {
1592 mos7840_port->SpRegOffset = 0x0;
1593 mos7840_port->ControlRegOffset = 0x1;
1594 mos7840_port->DcrRegOffset = 0x4;
1595 } else {
1596 u8 phy_num = mos7840_port->port_num;
1597
1598 /* Port 2 in the 2-port case uses registers of port 3 */
1599 if (serial->num_ports == 2)
1600 phy_num = 3;
1601
1602 mos7840_port->SpRegOffset = 0x8 + 2 * (phy_num - 2);
1603 mos7840_port->ControlRegOffset = 0x9 + 2 * (phy_num - 2);
1604 mos7840_port->DcrRegOffset = 0x16 + 3 * (phy_num - 2);
1605 }
1606 mos7840_dump_serial_port(port, mos7840_port);
1607 usb_set_serial_port_data(port, mos7840_port);
1608
1609 /* enable rx_disable bit in control register */
1610 status = mos7840_get_reg_sync(port,
1611 mos7840_port->ControlRegOffset, &Data);
1612 if (status < 0) {
1613 dev_dbg(&port->dev, "Reading ControlReg failed status-0x%x\n", status);
1614 goto error;
1615 } else
1616 dev_dbg(&port->dev, "ControlReg Reading success val is %x, status%d\n", Data, status);
1617 Data |= 0x08; /* setting driver done bit */
1618 Data |= 0x04; /* sp1_bit to have cts change reflect in
1619 modem status reg */
1620
1621 /* Data |= 0x20; //rx_disable bit */
1622 status = mos7840_set_reg_sync(port,
1623 mos7840_port->ControlRegOffset, Data);
1624 if (status < 0) {
1625 dev_dbg(&port->dev, "Writing ControlReg failed(rx_disable) status-0x%x\n", status);
1626 goto error;
1627 } else
1628 dev_dbg(&port->dev, "ControlReg Writing success(rx_disable) status%d\n", status);
1629
1630 /* Write default values in DCR (i.e 0x01 in DCR0, 0x05 in DCR2
1631 and 0x24 in DCR3 */
1632 Data = 0x01;
1633 status = mos7840_set_reg_sync(port,
1634 (__u16) (mos7840_port->DcrRegOffset + 0), Data);
1635 if (status < 0) {
1636 dev_dbg(&port->dev, "Writing DCR0 failed status-0x%x\n", status);
1637 goto error;
1638 } else
1639 dev_dbg(&port->dev, "DCR0 Writing success status%d\n", status);
1640
1641 Data = 0x05;
1642 status = mos7840_set_reg_sync(port,
1643 (__u16) (mos7840_port->DcrRegOffset + 1), Data);
1644 if (status < 0) {
1645 dev_dbg(&port->dev, "Writing DCR1 failed status-0x%x\n", status);
1646 goto error;
1647 } else
1648 dev_dbg(&port->dev, "DCR1 Writing success status%d\n", status);
1649
1650 Data = 0x24;
1651 status = mos7840_set_reg_sync(port,
1652 (__u16) (mos7840_port->DcrRegOffset + 2), Data);
1653 if (status < 0) {
1654 dev_dbg(&port->dev, "Writing DCR2 failed status-0x%x\n", status);
1655 goto error;
1656 } else
1657 dev_dbg(&port->dev, "DCR2 Writing success status%d\n", status);
1658
1659 /* write values in clkstart0x0 and clkmulti 0x20 */
1660 Data = 0x0;
1661 status = mos7840_set_reg_sync(port, CLK_START_VALUE_REGISTER, Data);
1662 if (status < 0) {
1663 dev_dbg(&port->dev, "Writing CLK_START_VALUE_REGISTER failed status-0x%x\n", status);
1664 goto error;
1665 } else
1666 dev_dbg(&port->dev, "CLK_START_VALUE_REGISTER Writing success status%d\n", status);
1667
1668 Data = 0x20;
1669 status = mos7840_set_reg_sync(port, CLK_MULTI_REGISTER, Data);
1670 if (status < 0) {
1671 dev_dbg(&port->dev, "Writing CLK_MULTI_REGISTER failed status-0x%x\n", status);
1672 goto error;
1673 } else
1674 dev_dbg(&port->dev, "CLK_MULTI_REGISTER Writing success status%d\n", status);
1675
1676 /* write value 0x0 to scratchpad register */
1677 Data = 0x00;
1678 status = mos7840_set_uart_reg(port, SCRATCH_PAD_REGISTER, Data);
1679 if (status < 0) {
1680 dev_dbg(&port->dev, "Writing SCRATCH_PAD_REGISTER failed status-0x%x\n", status);
1681 goto error;
1682 } else
1683 dev_dbg(&port->dev, "SCRATCH_PAD_REGISTER Writing success status%d\n", status);
1684
1685 /* Zero Length flag register */
1686 if ((mos7840_port->port_num != 1) && (serial->num_ports == 2)) {
1687 Data = 0xff;
1688 status = mos7840_set_reg_sync(port,
1689 (__u16) (ZLP_REG1 +
1690 ((__u16)mos7840_port->port_num)), Data);
1691 dev_dbg(&port->dev, "ZLIP offset %x\n",
1692 (__u16)(ZLP_REG1 + ((__u16) mos7840_port->port_num)));
1693 if (status < 0) {
1694 dev_dbg(&port->dev, "Writing ZLP_REG%d failed status-0x%x\n", pnum + 2, status);
1695 goto error;
1696 } else
1697 dev_dbg(&port->dev, "ZLP_REG%d Writing success status%d\n", pnum + 2, status);
1698 } else {
1699 Data = 0xff;
1700 status = mos7840_set_reg_sync(port,
1701 (__u16) (ZLP_REG1 +
1702 ((__u16)mos7840_port->port_num) - 0x1), Data);
1703 dev_dbg(&port->dev, "ZLIP offset %x\n",
1704 (__u16)(ZLP_REG1 + ((__u16) mos7840_port->port_num) - 0x1));
1705 if (status < 0) {
1706 dev_dbg(&port->dev, "Writing ZLP_REG%d failed status-0x%x\n", pnum + 1, status);
1707 goto error;
1708 } else
1709 dev_dbg(&port->dev, "ZLP_REG%d Writing success status%d\n", pnum + 1, status);
1710
1711 }
1712
1713 mos7840_port->has_led = device_flags & MCS_LED;
1714
1715 /* Initialize LED timers */
1716 if (mos7840_port->has_led) {
1717 mos7840_port->led_urb = usb_alloc_urb(0, GFP_KERNEL);
1718 mos7840_port->led_dr = kmalloc(sizeof(*mos7840_port->led_dr),
1719 GFP_KERNEL);
1720 if (!mos7840_port->led_urb || !mos7840_port->led_dr) {
1721 status = -ENOMEM;
1722 goto error;
1723 }
1724
1725 timer_setup(&mos7840_port->led_timer1, mos7840_led_off, 0);
1726 mos7840_port->led_timer1.expires =
1727 jiffies + msecs_to_jiffies(LED_ON_MS);
1728 timer_setup(&mos7840_port->led_timer2, mos7840_led_flag_off,
1729 0);
1730 mos7840_port->led_timer2.expires =
1731 jiffies + msecs_to_jiffies(LED_OFF_MS);
1732
1733 /* Turn off LED */
1734 mos7840_set_led_sync(port, MODEM_CONTROL_REGISTER, 0x0300);
1735 }
1736
1737 return 0;
1738error:
1739 kfree(mos7840_port->led_dr);
1740 usb_free_urb(mos7840_port->led_urb);
1741 kfree(mos7840_port);
1742
1743 return status;
1744}
1745
1746static int mos7840_port_remove(struct usb_serial_port *port)
1747{
1748 struct moschip_port *mos7840_port = usb_get_serial_port_data(port);
1749
1750 if (mos7840_port->has_led) {
1751 /* Turn off LED */
1752 mos7840_set_led_sync(port, MODEM_CONTROL_REGISTER, 0x0300);
1753
1754 del_timer_sync(&mos7840_port->led_timer1);
1755 del_timer_sync(&mos7840_port->led_timer2);
1756
1757 usb_kill_urb(mos7840_port->led_urb);
1758 usb_free_urb(mos7840_port->led_urb);
1759 kfree(mos7840_port->led_dr);
1760 }
1761
1762 kfree(mos7840_port);
1763
1764 return 0;
1765}
1766
1767static struct usb_serial_driver moschip7840_4port_device = {
1768 .driver = {
1769 .owner = THIS_MODULE,
1770 .name = "mos7840",
1771 },
1772 .description = DRIVER_DESC,
1773 .id_table = id_table,
1774 .num_interrupt_in = 1,
1775 .open = mos7840_open,
1776 .close = mos7840_close,
1777 .write = mos7840_write,
1778 .write_room = mos7840_write_room,
1779 .chars_in_buffer = mos7840_chars_in_buffer,
1780 .throttle = mos7840_throttle,
1781 .unthrottle = mos7840_unthrottle,
1782 .calc_num_ports = mos7840_calc_num_ports,
1783 .probe = mos7840_probe,
1784 .attach = mos7840_attach,
1785 .ioctl = mos7840_ioctl,
1786 .get_serial = mos7840_get_serial_info,
1787 .set_termios = mos7840_set_termios,
1788 .break_ctl = mos7840_break,
1789 .tiocmget = mos7840_tiocmget,
1790 .tiocmset = mos7840_tiocmset,
1791 .get_icount = usb_serial_generic_get_icount,
1792 .port_probe = mos7840_port_probe,
1793 .port_remove = mos7840_port_remove,
1794 .read_bulk_callback = mos7840_bulk_in_callback,
1795};
1796
1797static struct usb_serial_driver * const serial_drivers[] = {
1798 &moschip7840_4port_device, NULL
1799};
1800
1801module_usb_serial_driver(serial_drivers, id_table);
1802
1803MODULE_DESCRIPTION(DRIVER_DESC);
1804MODULE_LICENSE("GPL");