Loading...
1/*
2 * Driver for Atmel AT91 / AT32 Serial ports
3 * Copyright (C) 2003 Rick Bronson
4 *
5 * Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd.
6 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
7 *
8 * DMA support added by Chip Coldwell.
9 *
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of the GNU General Public License as published by
12 * the Free Software Foundation; either version 2 of the License, or
13 * (at your option) any later version.
14 *
15 * This program is distributed in the hope that it will be useful,
16 * but WITHOUT ANY WARRANTY; without even the implied warranty of
17 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
18 * GNU General Public License for more details.
19 *
20 * You should have received a copy of the GNU General Public License
21 * along with this program; if not, write to the Free Software
22 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
23 *
24 */
25#include <linux/tty.h>
26#include <linux/ioport.h>
27#include <linux/slab.h>
28#include <linux/init.h>
29#include <linux/serial.h>
30#include <linux/clk.h>
31#include <linux/console.h>
32#include <linux/sysrq.h>
33#include <linux/tty_flip.h>
34#include <linux/platform_device.h>
35#include <linux/of.h>
36#include <linux/of_device.h>
37#include <linux/of_gpio.h>
38#include <linux/dma-mapping.h>
39#include <linux/dmaengine.h>
40#include <linux/atmel_pdc.h>
41#include <linux/atmel_serial.h>
42#include <linux/uaccess.h>
43#include <linux/platform_data/atmel.h>
44#include <linux/timer.h>
45#include <linux/gpio.h>
46#include <linux/gpio/consumer.h>
47#include <linux/err.h>
48#include <linux/irq.h>
49#include <linux/suspend.h>
50
51#include <asm/io.h>
52#include <asm/ioctls.h>
53
54#define PDC_BUFFER_SIZE 512
55/* Revisit: We should calculate this based on the actual port settings */
56#define PDC_RX_TIMEOUT (3 * 10) /* 3 bytes */
57
58/* The minium number of data FIFOs should be able to contain */
59#define ATMEL_MIN_FIFO_SIZE 8
60/*
61 * These two offsets are substracted from the RX FIFO size to define the RTS
62 * high and low thresholds
63 */
64#define ATMEL_RTS_HIGH_OFFSET 16
65#define ATMEL_RTS_LOW_OFFSET 20
66
67#if defined(CONFIG_SERIAL_ATMEL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
68#define SUPPORT_SYSRQ
69#endif
70
71#include <linux/serial_core.h>
72
73#include "serial_mctrl_gpio.h"
74
75static void atmel_start_rx(struct uart_port *port);
76static void atmel_stop_rx(struct uart_port *port);
77
78#ifdef CONFIG_SERIAL_ATMEL_TTYAT
79
80/* Use device name ttyAT, major 204 and minor 154-169. This is necessary if we
81 * should coexist with the 8250 driver, such as if we have an external 16C550
82 * UART. */
83#define SERIAL_ATMEL_MAJOR 204
84#define MINOR_START 154
85#define ATMEL_DEVICENAME "ttyAT"
86
87#else
88
89/* Use device name ttyS, major 4, minor 64-68. This is the usual serial port
90 * name, but it is legally reserved for the 8250 driver. */
91#define SERIAL_ATMEL_MAJOR TTY_MAJOR
92#define MINOR_START 64
93#define ATMEL_DEVICENAME "ttyS"
94
95#endif
96
97#define ATMEL_ISR_PASS_LIMIT 256
98
99struct atmel_dma_buffer {
100 unsigned char *buf;
101 dma_addr_t dma_addr;
102 unsigned int dma_size;
103 unsigned int ofs;
104};
105
106struct atmel_uart_char {
107 u16 status;
108 u16 ch;
109};
110
111#define ATMEL_SERIAL_RINGSIZE 1024
112
113/*
114 * at91: 6 USARTs and one DBGU port (SAM9260)
115 * avr32: 4
116 */
117#define ATMEL_MAX_UART 7
118
119/*
120 * We wrap our port structure around the generic uart_port.
121 */
122struct atmel_uart_port {
123 struct uart_port uart; /* uart */
124 struct clk *clk; /* uart clock */
125 int may_wakeup; /* cached value of device_may_wakeup for times we need to disable it */
126 u32 backup_imr; /* IMR saved during suspend */
127 int break_active; /* break being received */
128
129 bool use_dma_rx; /* enable DMA receiver */
130 bool use_pdc_rx; /* enable PDC receiver */
131 short pdc_rx_idx; /* current PDC RX buffer */
132 struct atmel_dma_buffer pdc_rx[2]; /* PDC receier */
133
134 bool use_dma_tx; /* enable DMA transmitter */
135 bool use_pdc_tx; /* enable PDC transmitter */
136 struct atmel_dma_buffer pdc_tx; /* PDC transmitter */
137
138 spinlock_t lock_tx; /* port lock */
139 spinlock_t lock_rx; /* port lock */
140 struct dma_chan *chan_tx;
141 struct dma_chan *chan_rx;
142 struct dma_async_tx_descriptor *desc_tx;
143 struct dma_async_tx_descriptor *desc_rx;
144 dma_cookie_t cookie_tx;
145 dma_cookie_t cookie_rx;
146 struct scatterlist sg_tx;
147 struct scatterlist sg_rx;
148 struct tasklet_struct tasklet;
149 unsigned int irq_status;
150 unsigned int irq_status_prev;
151 unsigned int status_change;
152 unsigned int tx_len;
153
154 struct circ_buf rx_ring;
155
156 struct mctrl_gpios *gpios;
157 unsigned int tx_done_mask;
158 u32 fifo_size;
159 u32 rts_high;
160 u32 rts_low;
161 bool ms_irq_enabled;
162 u32 rtor; /* address of receiver timeout register if it exists */
163 bool has_hw_timer;
164 struct timer_list uart_timer;
165
166 bool suspended;
167 unsigned int pending;
168 unsigned int pending_status;
169 spinlock_t lock_suspended;
170
171 int (*prepare_rx)(struct uart_port *port);
172 int (*prepare_tx)(struct uart_port *port);
173 void (*schedule_rx)(struct uart_port *port);
174 void (*schedule_tx)(struct uart_port *port);
175 void (*release_rx)(struct uart_port *port);
176 void (*release_tx)(struct uart_port *port);
177};
178
179static struct atmel_uart_port atmel_ports[ATMEL_MAX_UART];
180static DECLARE_BITMAP(atmel_ports_in_use, ATMEL_MAX_UART);
181
182#ifdef SUPPORT_SYSRQ
183static struct console atmel_console;
184#endif
185
186#if defined(CONFIG_OF)
187static const struct of_device_id atmel_serial_dt_ids[] = {
188 { .compatible = "atmel,at91rm9200-usart" },
189 { .compatible = "atmel,at91sam9260-usart" },
190 { /* sentinel */ }
191};
192#endif
193
194static inline struct atmel_uart_port *
195to_atmel_uart_port(struct uart_port *uart)
196{
197 return container_of(uart, struct atmel_uart_port, uart);
198}
199
200static inline u32 atmel_uart_readl(struct uart_port *port, u32 reg)
201{
202 return __raw_readl(port->membase + reg);
203}
204
205static inline void atmel_uart_writel(struct uart_port *port, u32 reg, u32 value)
206{
207 __raw_writel(value, port->membase + reg);
208}
209
210#ifdef CONFIG_AVR32
211
212/* AVR32 cannot handle 8 or 16bit I/O accesses but only 32bit I/O accesses */
213static inline u8 atmel_uart_read_char(struct uart_port *port)
214{
215 return __raw_readl(port->membase + ATMEL_US_RHR);
216}
217
218static inline void atmel_uart_write_char(struct uart_port *port, u8 value)
219{
220 __raw_writel(value, port->membase + ATMEL_US_THR);
221}
222
223#else
224
225static inline u8 atmel_uart_read_char(struct uart_port *port)
226{
227 return __raw_readb(port->membase + ATMEL_US_RHR);
228}
229
230static inline void atmel_uart_write_char(struct uart_port *port, u8 value)
231{
232 __raw_writeb(value, port->membase + ATMEL_US_THR);
233}
234
235#endif
236
237#ifdef CONFIG_SERIAL_ATMEL_PDC
238static bool atmel_use_pdc_rx(struct uart_port *port)
239{
240 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
241
242 return atmel_port->use_pdc_rx;
243}
244
245static bool atmel_use_pdc_tx(struct uart_port *port)
246{
247 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
248
249 return atmel_port->use_pdc_tx;
250}
251#else
252static bool atmel_use_pdc_rx(struct uart_port *port)
253{
254 return false;
255}
256
257static bool atmel_use_pdc_tx(struct uart_port *port)
258{
259 return false;
260}
261#endif
262
263static bool atmel_use_dma_tx(struct uart_port *port)
264{
265 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
266
267 return atmel_port->use_dma_tx;
268}
269
270static bool atmel_use_dma_rx(struct uart_port *port)
271{
272 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
273
274 return atmel_port->use_dma_rx;
275}
276
277static unsigned int atmel_get_lines_status(struct uart_port *port)
278{
279 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
280 unsigned int status, ret = 0;
281
282 status = atmel_uart_readl(port, ATMEL_US_CSR);
283
284 mctrl_gpio_get(atmel_port->gpios, &ret);
285
286 if (!IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(atmel_port->gpios,
287 UART_GPIO_CTS))) {
288 if (ret & TIOCM_CTS)
289 status &= ~ATMEL_US_CTS;
290 else
291 status |= ATMEL_US_CTS;
292 }
293
294 if (!IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(atmel_port->gpios,
295 UART_GPIO_DSR))) {
296 if (ret & TIOCM_DSR)
297 status &= ~ATMEL_US_DSR;
298 else
299 status |= ATMEL_US_DSR;
300 }
301
302 if (!IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(atmel_port->gpios,
303 UART_GPIO_RI))) {
304 if (ret & TIOCM_RI)
305 status &= ~ATMEL_US_RI;
306 else
307 status |= ATMEL_US_RI;
308 }
309
310 if (!IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(atmel_port->gpios,
311 UART_GPIO_DCD))) {
312 if (ret & TIOCM_CD)
313 status &= ~ATMEL_US_DCD;
314 else
315 status |= ATMEL_US_DCD;
316 }
317
318 return status;
319}
320
321/* Enable or disable the rs485 support */
322static int atmel_config_rs485(struct uart_port *port,
323 struct serial_rs485 *rs485conf)
324{
325 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
326 unsigned int mode;
327
328 /* Disable interrupts */
329 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
330
331 mode = atmel_uart_readl(port, ATMEL_US_MR);
332
333 /* Resetting serial mode to RS232 (0x0) */
334 mode &= ~ATMEL_US_USMODE;
335
336 port->rs485 = *rs485conf;
337
338 if (rs485conf->flags & SER_RS485_ENABLED) {
339 dev_dbg(port->dev, "Setting UART to RS485\n");
340 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
341 atmel_uart_writel(port, ATMEL_US_TTGR,
342 rs485conf->delay_rts_after_send);
343 mode |= ATMEL_US_USMODE_RS485;
344 } else {
345 dev_dbg(port->dev, "Setting UART to RS232\n");
346 if (atmel_use_pdc_tx(port))
347 atmel_port->tx_done_mask = ATMEL_US_ENDTX |
348 ATMEL_US_TXBUFE;
349 else
350 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
351 }
352 atmel_uart_writel(port, ATMEL_US_MR, mode);
353
354 /* Enable interrupts */
355 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
356
357 return 0;
358}
359
360/*
361 * Return TIOCSER_TEMT when transmitter FIFO and Shift register is empty.
362 */
363static u_int atmel_tx_empty(struct uart_port *port)
364{
365 return (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXEMPTY) ?
366 TIOCSER_TEMT :
367 0;
368}
369
370/*
371 * Set state of the modem control output lines
372 */
373static void atmel_set_mctrl(struct uart_port *port, u_int mctrl)
374{
375 unsigned int control = 0;
376 unsigned int mode = atmel_uart_readl(port, ATMEL_US_MR);
377 unsigned int rts_paused, rts_ready;
378 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
379
380 /* override mode to RS485 if needed, otherwise keep the current mode */
381 if (port->rs485.flags & SER_RS485_ENABLED) {
382 atmel_uart_writel(port, ATMEL_US_TTGR,
383 port->rs485.delay_rts_after_send);
384 mode &= ~ATMEL_US_USMODE;
385 mode |= ATMEL_US_USMODE_RS485;
386 }
387
388 /* set the RTS line state according to the mode */
389 if ((mode & ATMEL_US_USMODE) == ATMEL_US_USMODE_HWHS) {
390 /* force RTS line to high level */
391 rts_paused = ATMEL_US_RTSEN;
392
393 /* give the control of the RTS line back to the hardware */
394 rts_ready = ATMEL_US_RTSDIS;
395 } else {
396 /* force RTS line to high level */
397 rts_paused = ATMEL_US_RTSDIS;
398
399 /* force RTS line to low level */
400 rts_ready = ATMEL_US_RTSEN;
401 }
402
403 if (mctrl & TIOCM_RTS)
404 control |= rts_ready;
405 else
406 control |= rts_paused;
407
408 if (mctrl & TIOCM_DTR)
409 control |= ATMEL_US_DTREN;
410 else
411 control |= ATMEL_US_DTRDIS;
412
413 atmel_uart_writel(port, ATMEL_US_CR, control);
414
415 mctrl_gpio_set(atmel_port->gpios, mctrl);
416
417 /* Local loopback mode? */
418 mode &= ~ATMEL_US_CHMODE;
419 if (mctrl & TIOCM_LOOP)
420 mode |= ATMEL_US_CHMODE_LOC_LOOP;
421 else
422 mode |= ATMEL_US_CHMODE_NORMAL;
423
424 atmel_uart_writel(port, ATMEL_US_MR, mode);
425}
426
427/*
428 * Get state of the modem control input lines
429 */
430static u_int atmel_get_mctrl(struct uart_port *port)
431{
432 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
433 unsigned int ret = 0, status;
434
435 status = atmel_uart_readl(port, ATMEL_US_CSR);
436
437 /*
438 * The control signals are active low.
439 */
440 if (!(status & ATMEL_US_DCD))
441 ret |= TIOCM_CD;
442 if (!(status & ATMEL_US_CTS))
443 ret |= TIOCM_CTS;
444 if (!(status & ATMEL_US_DSR))
445 ret |= TIOCM_DSR;
446 if (!(status & ATMEL_US_RI))
447 ret |= TIOCM_RI;
448
449 return mctrl_gpio_get(atmel_port->gpios, &ret);
450}
451
452/*
453 * Stop transmitting.
454 */
455static void atmel_stop_tx(struct uart_port *port)
456{
457 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
458
459 if (atmel_use_pdc_tx(port)) {
460 /* disable PDC transmit */
461 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
462 }
463 /* Disable interrupts */
464 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
465
466 if ((port->rs485.flags & SER_RS485_ENABLED) &&
467 !(port->rs485.flags & SER_RS485_RX_DURING_TX))
468 atmel_start_rx(port);
469}
470
471/*
472 * Start transmitting.
473 */
474static void atmel_start_tx(struct uart_port *port)
475{
476 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
477
478 if (atmel_use_pdc_tx(port)) {
479 if (atmel_uart_readl(port, ATMEL_PDC_PTSR) & ATMEL_PDC_TXTEN)
480 /* The transmitter is already running. Yes, we
481 really need this.*/
482 return;
483
484 if ((port->rs485.flags & SER_RS485_ENABLED) &&
485 !(port->rs485.flags & SER_RS485_RX_DURING_TX))
486 atmel_stop_rx(port);
487
488 /* re-enable PDC transmit */
489 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
490 }
491 /* Enable interrupts */
492 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
493}
494
495/*
496 * start receiving - port is in process of being opened.
497 */
498static void atmel_start_rx(struct uart_port *port)
499{
500 /* reset status and receiver */
501 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
502
503 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXEN);
504
505 if (atmel_use_pdc_rx(port)) {
506 /* enable PDC controller */
507 atmel_uart_writel(port, ATMEL_US_IER,
508 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
509 port->read_status_mask);
510 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
511 } else {
512 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY);
513 }
514}
515
516/*
517 * Stop receiving - port is in process of being closed.
518 */
519static void atmel_stop_rx(struct uart_port *port)
520{
521 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXDIS);
522
523 if (atmel_use_pdc_rx(port)) {
524 /* disable PDC receive */
525 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS);
526 atmel_uart_writel(port, ATMEL_US_IDR,
527 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
528 port->read_status_mask);
529 } else {
530 atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXRDY);
531 }
532}
533
534/*
535 * Enable modem status interrupts
536 */
537static void atmel_enable_ms(struct uart_port *port)
538{
539 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
540 uint32_t ier = 0;
541
542 /*
543 * Interrupt should not be enabled twice
544 */
545 if (atmel_port->ms_irq_enabled)
546 return;
547
548 atmel_port->ms_irq_enabled = true;
549
550 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
551 ier |= ATMEL_US_CTSIC;
552
553 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DSR))
554 ier |= ATMEL_US_DSRIC;
555
556 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_RI))
557 ier |= ATMEL_US_RIIC;
558
559 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DCD))
560 ier |= ATMEL_US_DCDIC;
561
562 atmel_uart_writel(port, ATMEL_US_IER, ier);
563
564 mctrl_gpio_enable_ms(atmel_port->gpios);
565}
566
567/*
568 * Disable modem status interrupts
569 */
570static void atmel_disable_ms(struct uart_port *port)
571{
572 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
573 uint32_t idr = 0;
574
575 /*
576 * Interrupt should not be disabled twice
577 */
578 if (!atmel_port->ms_irq_enabled)
579 return;
580
581 atmel_port->ms_irq_enabled = false;
582
583 mctrl_gpio_disable_ms(atmel_port->gpios);
584
585 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
586 idr |= ATMEL_US_CTSIC;
587
588 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DSR))
589 idr |= ATMEL_US_DSRIC;
590
591 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_RI))
592 idr |= ATMEL_US_RIIC;
593
594 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DCD))
595 idr |= ATMEL_US_DCDIC;
596
597 atmel_uart_writel(port, ATMEL_US_IDR, idr);
598}
599
600/*
601 * Control the transmission of a break signal
602 */
603static void atmel_break_ctl(struct uart_port *port, int break_state)
604{
605 if (break_state != 0)
606 /* start break */
607 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTBRK);
608 else
609 /* stop break */
610 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STPBRK);
611}
612
613/*
614 * Stores the incoming character in the ring buffer
615 */
616static void
617atmel_buffer_rx_char(struct uart_port *port, unsigned int status,
618 unsigned int ch)
619{
620 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
621 struct circ_buf *ring = &atmel_port->rx_ring;
622 struct atmel_uart_char *c;
623
624 if (!CIRC_SPACE(ring->head, ring->tail, ATMEL_SERIAL_RINGSIZE))
625 /* Buffer overflow, ignore char */
626 return;
627
628 c = &((struct atmel_uart_char *)ring->buf)[ring->head];
629 c->status = status;
630 c->ch = ch;
631
632 /* Make sure the character is stored before we update head. */
633 smp_wmb();
634
635 ring->head = (ring->head + 1) & (ATMEL_SERIAL_RINGSIZE - 1);
636}
637
638/*
639 * Deal with parity, framing and overrun errors.
640 */
641static void atmel_pdc_rxerr(struct uart_port *port, unsigned int status)
642{
643 /* clear error */
644 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
645
646 if (status & ATMEL_US_RXBRK) {
647 /* ignore side-effect */
648 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);
649 port->icount.brk++;
650 }
651 if (status & ATMEL_US_PARE)
652 port->icount.parity++;
653 if (status & ATMEL_US_FRAME)
654 port->icount.frame++;
655 if (status & ATMEL_US_OVRE)
656 port->icount.overrun++;
657}
658
659/*
660 * Characters received (called from interrupt handler)
661 */
662static void atmel_rx_chars(struct uart_port *port)
663{
664 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
665 unsigned int status, ch;
666
667 status = atmel_uart_readl(port, ATMEL_US_CSR);
668 while (status & ATMEL_US_RXRDY) {
669 ch = atmel_uart_read_char(port);
670
671 /*
672 * note that the error handling code is
673 * out of the main execution path
674 */
675 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME
676 | ATMEL_US_OVRE | ATMEL_US_RXBRK)
677 || atmel_port->break_active)) {
678
679 /* clear error */
680 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
681
682 if (status & ATMEL_US_RXBRK
683 && !atmel_port->break_active) {
684 atmel_port->break_active = 1;
685 atmel_uart_writel(port, ATMEL_US_IER,
686 ATMEL_US_RXBRK);
687 } else {
688 /*
689 * This is either the end-of-break
690 * condition or we've received at
691 * least one character without RXBRK
692 * being set. In both cases, the next
693 * RXBRK will indicate start-of-break.
694 */
695 atmel_uart_writel(port, ATMEL_US_IDR,
696 ATMEL_US_RXBRK);
697 status &= ~ATMEL_US_RXBRK;
698 atmel_port->break_active = 0;
699 }
700 }
701
702 atmel_buffer_rx_char(port, status, ch);
703 status = atmel_uart_readl(port, ATMEL_US_CSR);
704 }
705
706 tasklet_schedule(&atmel_port->tasklet);
707}
708
709/*
710 * Transmit characters (called from tasklet with TXRDY interrupt
711 * disabled)
712 */
713static void atmel_tx_chars(struct uart_port *port)
714{
715 struct circ_buf *xmit = &port->state->xmit;
716 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
717
718 if (port->x_char &&
719 (atmel_uart_readl(port, ATMEL_US_CSR) & atmel_port->tx_done_mask)) {
720 atmel_uart_write_char(port, port->x_char);
721 port->icount.tx++;
722 port->x_char = 0;
723 }
724 if (uart_circ_empty(xmit) || uart_tx_stopped(port))
725 return;
726
727 while (atmel_uart_readl(port, ATMEL_US_CSR) &
728 atmel_port->tx_done_mask) {
729 atmel_uart_write_char(port, xmit->buf[xmit->tail]);
730 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
731 port->icount.tx++;
732 if (uart_circ_empty(xmit))
733 break;
734 }
735
736 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
737 uart_write_wakeup(port);
738
739 if (!uart_circ_empty(xmit))
740 /* Enable interrupts */
741 atmel_uart_writel(port, ATMEL_US_IER,
742 atmel_port->tx_done_mask);
743}
744
745static void atmel_complete_tx_dma(void *arg)
746{
747 struct atmel_uart_port *atmel_port = arg;
748 struct uart_port *port = &atmel_port->uart;
749 struct circ_buf *xmit = &port->state->xmit;
750 struct dma_chan *chan = atmel_port->chan_tx;
751 unsigned long flags;
752
753 spin_lock_irqsave(&port->lock, flags);
754
755 if (chan)
756 dmaengine_terminate_all(chan);
757 xmit->tail += atmel_port->tx_len;
758 xmit->tail &= UART_XMIT_SIZE - 1;
759
760 port->icount.tx += atmel_port->tx_len;
761
762 spin_lock_irq(&atmel_port->lock_tx);
763 async_tx_ack(atmel_port->desc_tx);
764 atmel_port->cookie_tx = -EINVAL;
765 atmel_port->desc_tx = NULL;
766 spin_unlock_irq(&atmel_port->lock_tx);
767
768 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
769 uart_write_wakeup(port);
770
771 /*
772 * xmit is a circular buffer so, if we have just send data from
773 * xmit->tail to the end of xmit->buf, now we have to transmit the
774 * remaining data from the beginning of xmit->buf to xmit->head.
775 */
776 if (!uart_circ_empty(xmit))
777 tasklet_schedule(&atmel_port->tasklet);
778
779 spin_unlock_irqrestore(&port->lock, flags);
780}
781
782static void atmel_release_tx_dma(struct uart_port *port)
783{
784 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
785 struct dma_chan *chan = atmel_port->chan_tx;
786
787 if (chan) {
788 dmaengine_terminate_all(chan);
789 dma_release_channel(chan);
790 dma_unmap_sg(port->dev, &atmel_port->sg_tx, 1,
791 DMA_TO_DEVICE);
792 }
793
794 atmel_port->desc_tx = NULL;
795 atmel_port->chan_tx = NULL;
796 atmel_port->cookie_tx = -EINVAL;
797}
798
799/*
800 * Called from tasklet with TXRDY interrupt is disabled.
801 */
802static void atmel_tx_dma(struct uart_port *port)
803{
804 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
805 struct circ_buf *xmit = &port->state->xmit;
806 struct dma_chan *chan = atmel_port->chan_tx;
807 struct dma_async_tx_descriptor *desc;
808 struct scatterlist sgl[2], *sg, *sg_tx = &atmel_port->sg_tx;
809 unsigned int tx_len, part1_len, part2_len, sg_len;
810 dma_addr_t phys_addr;
811
812 /* Make sure we have an idle channel */
813 if (atmel_port->desc_tx != NULL)
814 return;
815
816 if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) {
817 /*
818 * DMA is idle now.
819 * Port xmit buffer is already mapped,
820 * and it is one page... Just adjust
821 * offsets and lengths. Since it is a circular buffer,
822 * we have to transmit till the end, and then the rest.
823 * Take the port lock to get a
824 * consistent xmit buffer state.
825 */
826 tx_len = CIRC_CNT_TO_END(xmit->head,
827 xmit->tail,
828 UART_XMIT_SIZE);
829
830 if (atmel_port->fifo_size) {
831 /* multi data mode */
832 part1_len = (tx_len & ~0x3); /* DWORD access */
833 part2_len = (tx_len & 0x3); /* BYTE access */
834 } else {
835 /* single data (legacy) mode */
836 part1_len = 0;
837 part2_len = tx_len; /* BYTE access only */
838 }
839
840 sg_init_table(sgl, 2);
841 sg_len = 0;
842 phys_addr = sg_dma_address(sg_tx) + xmit->tail;
843 if (part1_len) {
844 sg = &sgl[sg_len++];
845 sg_dma_address(sg) = phys_addr;
846 sg_dma_len(sg) = part1_len;
847
848 phys_addr += part1_len;
849 }
850
851 if (part2_len) {
852 sg = &sgl[sg_len++];
853 sg_dma_address(sg) = phys_addr;
854 sg_dma_len(sg) = part2_len;
855 }
856
857 /*
858 * save tx_len so atmel_complete_tx_dma() will increase
859 * xmit->tail correctly
860 */
861 atmel_port->tx_len = tx_len;
862
863 desc = dmaengine_prep_slave_sg(chan,
864 sgl,
865 sg_len,
866 DMA_MEM_TO_DEV,
867 DMA_PREP_INTERRUPT |
868 DMA_CTRL_ACK);
869 if (!desc) {
870 dev_err(port->dev, "Failed to send via dma!\n");
871 return;
872 }
873
874 dma_sync_sg_for_device(port->dev, sg_tx, 1, DMA_TO_DEVICE);
875
876 atmel_port->desc_tx = desc;
877 desc->callback = atmel_complete_tx_dma;
878 desc->callback_param = atmel_port;
879 atmel_port->cookie_tx = dmaengine_submit(desc);
880
881 } else {
882 if (port->rs485.flags & SER_RS485_ENABLED) {
883 /* DMA done, stop TX, start RX for RS485 */
884 atmel_start_rx(port);
885 }
886 }
887
888 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
889 uart_write_wakeup(port);
890}
891
892static int atmel_prepare_tx_dma(struct uart_port *port)
893{
894 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
895 dma_cap_mask_t mask;
896 struct dma_slave_config config;
897 int ret, nent;
898
899 dma_cap_zero(mask);
900 dma_cap_set(DMA_SLAVE, mask);
901
902 atmel_port->chan_tx = dma_request_slave_channel(port->dev, "tx");
903 if (atmel_port->chan_tx == NULL)
904 goto chan_err;
905 dev_info(port->dev, "using %s for tx DMA transfers\n",
906 dma_chan_name(atmel_port->chan_tx));
907
908 spin_lock_init(&atmel_port->lock_tx);
909 sg_init_table(&atmel_port->sg_tx, 1);
910 /* UART circular tx buffer is an aligned page. */
911 BUG_ON(!PAGE_ALIGNED(port->state->xmit.buf));
912 sg_set_page(&atmel_port->sg_tx,
913 virt_to_page(port->state->xmit.buf),
914 UART_XMIT_SIZE,
915 (unsigned long)port->state->xmit.buf & ~PAGE_MASK);
916 nent = dma_map_sg(port->dev,
917 &atmel_port->sg_tx,
918 1,
919 DMA_TO_DEVICE);
920
921 if (!nent) {
922 dev_dbg(port->dev, "need to release resource of dma\n");
923 goto chan_err;
924 } else {
925 dev_dbg(port->dev, "%s: mapped %d@%p to %pad\n", __func__,
926 sg_dma_len(&atmel_port->sg_tx),
927 port->state->xmit.buf,
928 &sg_dma_address(&atmel_port->sg_tx));
929 }
930
931 /* Configure the slave DMA */
932 memset(&config, 0, sizeof(config));
933 config.direction = DMA_MEM_TO_DEV;
934 config.dst_addr_width = (atmel_port->fifo_size) ?
935 DMA_SLAVE_BUSWIDTH_4_BYTES :
936 DMA_SLAVE_BUSWIDTH_1_BYTE;
937 config.dst_addr = port->mapbase + ATMEL_US_THR;
938 config.dst_maxburst = 1;
939
940 ret = dmaengine_slave_config(atmel_port->chan_tx,
941 &config);
942 if (ret) {
943 dev_err(port->dev, "DMA tx slave configuration failed\n");
944 goto chan_err;
945 }
946
947 return 0;
948
949chan_err:
950 dev_err(port->dev, "TX channel not available, switch to pio\n");
951 atmel_port->use_dma_tx = 0;
952 if (atmel_port->chan_tx)
953 atmel_release_tx_dma(port);
954 return -EINVAL;
955}
956
957static void atmel_complete_rx_dma(void *arg)
958{
959 struct uart_port *port = arg;
960 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
961
962 tasklet_schedule(&atmel_port->tasklet);
963}
964
965static void atmel_release_rx_dma(struct uart_port *port)
966{
967 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
968 struct dma_chan *chan = atmel_port->chan_rx;
969
970 if (chan) {
971 dmaengine_terminate_all(chan);
972 dma_release_channel(chan);
973 dma_unmap_sg(port->dev, &atmel_port->sg_rx, 1,
974 DMA_FROM_DEVICE);
975 }
976
977 atmel_port->desc_rx = NULL;
978 atmel_port->chan_rx = NULL;
979 atmel_port->cookie_rx = -EINVAL;
980}
981
982static void atmel_rx_from_dma(struct uart_port *port)
983{
984 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
985 struct tty_port *tport = &port->state->port;
986 struct circ_buf *ring = &atmel_port->rx_ring;
987 struct dma_chan *chan = atmel_port->chan_rx;
988 struct dma_tx_state state;
989 enum dma_status dmastat;
990 size_t count;
991
992
993 /* Reset the UART timeout early so that we don't miss one */
994 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
995 dmastat = dmaengine_tx_status(chan,
996 atmel_port->cookie_rx,
997 &state);
998 /* Restart a new tasklet if DMA status is error */
999 if (dmastat == DMA_ERROR) {
1000 dev_dbg(port->dev, "Get residue error, restart tasklet\n");
1001 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT);
1002 tasklet_schedule(&atmel_port->tasklet);
1003 return;
1004 }
1005
1006 /* CPU claims ownership of RX DMA buffer */
1007 dma_sync_sg_for_cpu(port->dev,
1008 &atmel_port->sg_rx,
1009 1,
1010 DMA_FROM_DEVICE);
1011
1012 /*
1013 * ring->head points to the end of data already written by the DMA.
1014 * ring->tail points to the beginning of data to be read by the
1015 * framework.
1016 * The current transfer size should not be larger than the dma buffer
1017 * length.
1018 */
1019 ring->head = sg_dma_len(&atmel_port->sg_rx) - state.residue;
1020 BUG_ON(ring->head > sg_dma_len(&atmel_port->sg_rx));
1021 /*
1022 * At this point ring->head may point to the first byte right after the
1023 * last byte of the dma buffer:
1024 * 0 <= ring->head <= sg_dma_len(&atmel_port->sg_rx)
1025 *
1026 * However ring->tail must always points inside the dma buffer:
1027 * 0 <= ring->tail <= sg_dma_len(&atmel_port->sg_rx) - 1
1028 *
1029 * Since we use a ring buffer, we have to handle the case
1030 * where head is lower than tail. In such a case, we first read from
1031 * tail to the end of the buffer then reset tail.
1032 */
1033 if (ring->head < ring->tail) {
1034 count = sg_dma_len(&atmel_port->sg_rx) - ring->tail;
1035
1036 tty_insert_flip_string(tport, ring->buf + ring->tail, count);
1037 ring->tail = 0;
1038 port->icount.rx += count;
1039 }
1040
1041 /* Finally we read data from tail to head */
1042 if (ring->tail < ring->head) {
1043 count = ring->head - ring->tail;
1044
1045 tty_insert_flip_string(tport, ring->buf + ring->tail, count);
1046 /* Wrap ring->head if needed */
1047 if (ring->head >= sg_dma_len(&atmel_port->sg_rx))
1048 ring->head = 0;
1049 ring->tail = ring->head;
1050 port->icount.rx += count;
1051 }
1052
1053 /* USART retreives ownership of RX DMA buffer */
1054 dma_sync_sg_for_device(port->dev,
1055 &atmel_port->sg_rx,
1056 1,
1057 DMA_FROM_DEVICE);
1058
1059 /*
1060 * Drop the lock here since it might end up calling
1061 * uart_start(), which takes the lock.
1062 */
1063 spin_unlock(&port->lock);
1064 tty_flip_buffer_push(tport);
1065 spin_lock(&port->lock);
1066
1067 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT);
1068}
1069
1070static int atmel_prepare_rx_dma(struct uart_port *port)
1071{
1072 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1073 struct dma_async_tx_descriptor *desc;
1074 dma_cap_mask_t mask;
1075 struct dma_slave_config config;
1076 struct circ_buf *ring;
1077 int ret, nent;
1078
1079 ring = &atmel_port->rx_ring;
1080
1081 dma_cap_zero(mask);
1082 dma_cap_set(DMA_CYCLIC, mask);
1083
1084 atmel_port->chan_rx = dma_request_slave_channel(port->dev, "rx");
1085 if (atmel_port->chan_rx == NULL)
1086 goto chan_err;
1087 dev_info(port->dev, "using %s for rx DMA transfers\n",
1088 dma_chan_name(atmel_port->chan_rx));
1089
1090 spin_lock_init(&atmel_port->lock_rx);
1091 sg_init_table(&atmel_port->sg_rx, 1);
1092 /* UART circular rx buffer is an aligned page. */
1093 BUG_ON(!PAGE_ALIGNED(ring->buf));
1094 sg_set_page(&atmel_port->sg_rx,
1095 virt_to_page(ring->buf),
1096 sizeof(struct atmel_uart_char) * ATMEL_SERIAL_RINGSIZE,
1097 (unsigned long)ring->buf & ~PAGE_MASK);
1098 nent = dma_map_sg(port->dev,
1099 &atmel_port->sg_rx,
1100 1,
1101 DMA_FROM_DEVICE);
1102
1103 if (!nent) {
1104 dev_dbg(port->dev, "need to release resource of dma\n");
1105 goto chan_err;
1106 } else {
1107 dev_dbg(port->dev, "%s: mapped %d@%p to %pad\n", __func__,
1108 sg_dma_len(&atmel_port->sg_rx),
1109 ring->buf,
1110 &sg_dma_address(&atmel_port->sg_rx));
1111 }
1112
1113 /* Configure the slave DMA */
1114 memset(&config, 0, sizeof(config));
1115 config.direction = DMA_DEV_TO_MEM;
1116 config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
1117 config.src_addr = port->mapbase + ATMEL_US_RHR;
1118 config.src_maxburst = 1;
1119
1120 ret = dmaengine_slave_config(atmel_port->chan_rx,
1121 &config);
1122 if (ret) {
1123 dev_err(port->dev, "DMA rx slave configuration failed\n");
1124 goto chan_err;
1125 }
1126 /*
1127 * Prepare a cyclic dma transfer, assign 2 descriptors,
1128 * each one is half ring buffer size
1129 */
1130 desc = dmaengine_prep_dma_cyclic(atmel_port->chan_rx,
1131 sg_dma_address(&atmel_port->sg_rx),
1132 sg_dma_len(&atmel_port->sg_rx),
1133 sg_dma_len(&atmel_port->sg_rx)/2,
1134 DMA_DEV_TO_MEM,
1135 DMA_PREP_INTERRUPT);
1136 desc->callback = atmel_complete_rx_dma;
1137 desc->callback_param = port;
1138 atmel_port->desc_rx = desc;
1139 atmel_port->cookie_rx = dmaengine_submit(desc);
1140
1141 return 0;
1142
1143chan_err:
1144 dev_err(port->dev, "RX channel not available, switch to pio\n");
1145 atmel_port->use_dma_rx = 0;
1146 if (atmel_port->chan_rx)
1147 atmel_release_rx_dma(port);
1148 return -EINVAL;
1149}
1150
1151static void atmel_uart_timer_callback(unsigned long data)
1152{
1153 struct uart_port *port = (void *)data;
1154 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1155
1156 tasklet_schedule(&atmel_port->tasklet);
1157 mod_timer(&atmel_port->uart_timer, jiffies + uart_poll_timeout(port));
1158}
1159
1160/*
1161 * receive interrupt handler.
1162 */
1163static void
1164atmel_handle_receive(struct uart_port *port, unsigned int pending)
1165{
1166 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1167
1168 if (atmel_use_pdc_rx(port)) {
1169 /*
1170 * PDC receive. Just schedule the tasklet and let it
1171 * figure out the details.
1172 *
1173 * TODO: We're not handling error flags correctly at
1174 * the moment.
1175 */
1176 if (pending & (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)) {
1177 atmel_uart_writel(port, ATMEL_US_IDR,
1178 (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT));
1179 tasklet_schedule(&atmel_port->tasklet);
1180 }
1181
1182 if (pending & (ATMEL_US_RXBRK | ATMEL_US_OVRE |
1183 ATMEL_US_FRAME | ATMEL_US_PARE))
1184 atmel_pdc_rxerr(port, pending);
1185 }
1186
1187 if (atmel_use_dma_rx(port)) {
1188 if (pending & ATMEL_US_TIMEOUT) {
1189 atmel_uart_writel(port, ATMEL_US_IDR,
1190 ATMEL_US_TIMEOUT);
1191 tasklet_schedule(&atmel_port->tasklet);
1192 }
1193 }
1194
1195 /* Interrupt receive */
1196 if (pending & ATMEL_US_RXRDY)
1197 atmel_rx_chars(port);
1198 else if (pending & ATMEL_US_RXBRK) {
1199 /*
1200 * End of break detected. If it came along with a
1201 * character, atmel_rx_chars will handle it.
1202 */
1203 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
1204 atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXBRK);
1205 atmel_port->break_active = 0;
1206 }
1207}
1208
1209/*
1210 * transmit interrupt handler. (Transmit is IRQF_NODELAY safe)
1211 */
1212static void
1213atmel_handle_transmit(struct uart_port *port, unsigned int pending)
1214{
1215 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1216
1217 if (pending & atmel_port->tx_done_mask) {
1218 /* Either PDC or interrupt transmission */
1219 atmel_uart_writel(port, ATMEL_US_IDR,
1220 atmel_port->tx_done_mask);
1221 tasklet_schedule(&atmel_port->tasklet);
1222 }
1223}
1224
1225/*
1226 * status flags interrupt handler.
1227 */
1228static void
1229atmel_handle_status(struct uart_port *port, unsigned int pending,
1230 unsigned int status)
1231{
1232 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1233
1234 if (pending & (ATMEL_US_RIIC | ATMEL_US_DSRIC | ATMEL_US_DCDIC
1235 | ATMEL_US_CTSIC)) {
1236 atmel_port->irq_status = status;
1237 atmel_port->status_change = atmel_port->irq_status ^
1238 atmel_port->irq_status_prev;
1239 atmel_port->irq_status_prev = status;
1240 tasklet_schedule(&atmel_port->tasklet);
1241 }
1242}
1243
1244/*
1245 * Interrupt handler
1246 */
1247static irqreturn_t atmel_interrupt(int irq, void *dev_id)
1248{
1249 struct uart_port *port = dev_id;
1250 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1251 unsigned int status, pending, mask, pass_counter = 0;
1252
1253 spin_lock(&atmel_port->lock_suspended);
1254
1255 do {
1256 status = atmel_get_lines_status(port);
1257 mask = atmel_uart_readl(port, ATMEL_US_IMR);
1258 pending = status & mask;
1259 if (!pending)
1260 break;
1261
1262 if (atmel_port->suspended) {
1263 atmel_port->pending |= pending;
1264 atmel_port->pending_status = status;
1265 atmel_uart_writel(port, ATMEL_US_IDR, mask);
1266 pm_system_wakeup();
1267 break;
1268 }
1269
1270 atmel_handle_receive(port, pending);
1271 atmel_handle_status(port, pending, status);
1272 atmel_handle_transmit(port, pending);
1273 } while (pass_counter++ < ATMEL_ISR_PASS_LIMIT);
1274
1275 spin_unlock(&atmel_port->lock_suspended);
1276
1277 return pass_counter ? IRQ_HANDLED : IRQ_NONE;
1278}
1279
1280static void atmel_release_tx_pdc(struct uart_port *port)
1281{
1282 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1283 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1284
1285 dma_unmap_single(port->dev,
1286 pdc->dma_addr,
1287 pdc->dma_size,
1288 DMA_TO_DEVICE);
1289}
1290
1291/*
1292 * Called from tasklet with ENDTX and TXBUFE interrupts disabled.
1293 */
1294static void atmel_tx_pdc(struct uart_port *port)
1295{
1296 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1297 struct circ_buf *xmit = &port->state->xmit;
1298 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1299 int count;
1300
1301 /* nothing left to transmit? */
1302 if (atmel_uart_readl(port, ATMEL_PDC_TCR))
1303 return;
1304
1305 xmit->tail += pdc->ofs;
1306 xmit->tail &= UART_XMIT_SIZE - 1;
1307
1308 port->icount.tx += pdc->ofs;
1309 pdc->ofs = 0;
1310
1311 /* more to transmit - setup next transfer */
1312
1313 /* disable PDC transmit */
1314 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
1315
1316 if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) {
1317 dma_sync_single_for_device(port->dev,
1318 pdc->dma_addr,
1319 pdc->dma_size,
1320 DMA_TO_DEVICE);
1321
1322 count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
1323 pdc->ofs = count;
1324
1325 atmel_uart_writel(port, ATMEL_PDC_TPR,
1326 pdc->dma_addr + xmit->tail);
1327 atmel_uart_writel(port, ATMEL_PDC_TCR, count);
1328 /* re-enable PDC transmit */
1329 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
1330 /* Enable interrupts */
1331 atmel_uart_writel(port, ATMEL_US_IER,
1332 atmel_port->tx_done_mask);
1333 } else {
1334 if ((port->rs485.flags & SER_RS485_ENABLED) &&
1335 !(port->rs485.flags & SER_RS485_RX_DURING_TX)) {
1336 /* DMA done, stop TX, start RX for RS485 */
1337 atmel_start_rx(port);
1338 }
1339 }
1340
1341 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
1342 uart_write_wakeup(port);
1343}
1344
1345static int atmel_prepare_tx_pdc(struct uart_port *port)
1346{
1347 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1348 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1349 struct circ_buf *xmit = &port->state->xmit;
1350
1351 pdc->buf = xmit->buf;
1352 pdc->dma_addr = dma_map_single(port->dev,
1353 pdc->buf,
1354 UART_XMIT_SIZE,
1355 DMA_TO_DEVICE);
1356 pdc->dma_size = UART_XMIT_SIZE;
1357 pdc->ofs = 0;
1358
1359 return 0;
1360}
1361
1362static void atmel_rx_from_ring(struct uart_port *port)
1363{
1364 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1365 struct circ_buf *ring = &atmel_port->rx_ring;
1366 unsigned int flg;
1367 unsigned int status;
1368
1369 while (ring->head != ring->tail) {
1370 struct atmel_uart_char c;
1371
1372 /* Make sure c is loaded after head. */
1373 smp_rmb();
1374
1375 c = ((struct atmel_uart_char *)ring->buf)[ring->tail];
1376
1377 ring->tail = (ring->tail + 1) & (ATMEL_SERIAL_RINGSIZE - 1);
1378
1379 port->icount.rx++;
1380 status = c.status;
1381 flg = TTY_NORMAL;
1382
1383 /*
1384 * note that the error handling code is
1385 * out of the main execution path
1386 */
1387 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME
1388 | ATMEL_US_OVRE | ATMEL_US_RXBRK))) {
1389 if (status & ATMEL_US_RXBRK) {
1390 /* ignore side-effect */
1391 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);
1392
1393 port->icount.brk++;
1394 if (uart_handle_break(port))
1395 continue;
1396 }
1397 if (status & ATMEL_US_PARE)
1398 port->icount.parity++;
1399 if (status & ATMEL_US_FRAME)
1400 port->icount.frame++;
1401 if (status & ATMEL_US_OVRE)
1402 port->icount.overrun++;
1403
1404 status &= port->read_status_mask;
1405
1406 if (status & ATMEL_US_RXBRK)
1407 flg = TTY_BREAK;
1408 else if (status & ATMEL_US_PARE)
1409 flg = TTY_PARITY;
1410 else if (status & ATMEL_US_FRAME)
1411 flg = TTY_FRAME;
1412 }
1413
1414
1415 if (uart_handle_sysrq_char(port, c.ch))
1416 continue;
1417
1418 uart_insert_char(port, status, ATMEL_US_OVRE, c.ch, flg);
1419 }
1420
1421 /*
1422 * Drop the lock here since it might end up calling
1423 * uart_start(), which takes the lock.
1424 */
1425 spin_unlock(&port->lock);
1426 tty_flip_buffer_push(&port->state->port);
1427 spin_lock(&port->lock);
1428}
1429
1430static void atmel_release_rx_pdc(struct uart_port *port)
1431{
1432 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1433 int i;
1434
1435 for (i = 0; i < 2; i++) {
1436 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
1437
1438 dma_unmap_single(port->dev,
1439 pdc->dma_addr,
1440 pdc->dma_size,
1441 DMA_FROM_DEVICE);
1442 kfree(pdc->buf);
1443 }
1444}
1445
1446static void atmel_rx_from_pdc(struct uart_port *port)
1447{
1448 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1449 struct tty_port *tport = &port->state->port;
1450 struct atmel_dma_buffer *pdc;
1451 int rx_idx = atmel_port->pdc_rx_idx;
1452 unsigned int head;
1453 unsigned int tail;
1454 unsigned int count;
1455
1456 do {
1457 /* Reset the UART timeout early so that we don't miss one */
1458 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1459
1460 pdc = &atmel_port->pdc_rx[rx_idx];
1461 head = atmel_uart_readl(port, ATMEL_PDC_RPR) - pdc->dma_addr;
1462 tail = pdc->ofs;
1463
1464 /* If the PDC has switched buffers, RPR won't contain
1465 * any address within the current buffer. Since head
1466 * is unsigned, we just need a one-way comparison to
1467 * find out.
1468 *
1469 * In this case, we just need to consume the entire
1470 * buffer and resubmit it for DMA. This will clear the
1471 * ENDRX bit as well, so that we can safely re-enable
1472 * all interrupts below.
1473 */
1474 head = min(head, pdc->dma_size);
1475
1476 if (likely(head != tail)) {
1477 dma_sync_single_for_cpu(port->dev, pdc->dma_addr,
1478 pdc->dma_size, DMA_FROM_DEVICE);
1479
1480 /*
1481 * head will only wrap around when we recycle
1482 * the DMA buffer, and when that happens, we
1483 * explicitly set tail to 0. So head will
1484 * always be greater than tail.
1485 */
1486 count = head - tail;
1487
1488 tty_insert_flip_string(tport, pdc->buf + pdc->ofs,
1489 count);
1490
1491 dma_sync_single_for_device(port->dev, pdc->dma_addr,
1492 pdc->dma_size, DMA_FROM_DEVICE);
1493
1494 port->icount.rx += count;
1495 pdc->ofs = head;
1496 }
1497
1498 /*
1499 * If the current buffer is full, we need to check if
1500 * the next one contains any additional data.
1501 */
1502 if (head >= pdc->dma_size) {
1503 pdc->ofs = 0;
1504 atmel_uart_writel(port, ATMEL_PDC_RNPR, pdc->dma_addr);
1505 atmel_uart_writel(port, ATMEL_PDC_RNCR, pdc->dma_size);
1506
1507 rx_idx = !rx_idx;
1508 atmel_port->pdc_rx_idx = rx_idx;
1509 }
1510 } while (head >= pdc->dma_size);
1511
1512 /*
1513 * Drop the lock here since it might end up calling
1514 * uart_start(), which takes the lock.
1515 */
1516 spin_unlock(&port->lock);
1517 tty_flip_buffer_push(tport);
1518 spin_lock(&port->lock);
1519
1520 atmel_uart_writel(port, ATMEL_US_IER,
1521 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
1522}
1523
1524static int atmel_prepare_rx_pdc(struct uart_port *port)
1525{
1526 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1527 int i;
1528
1529 for (i = 0; i < 2; i++) {
1530 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
1531
1532 pdc->buf = kmalloc(PDC_BUFFER_SIZE, GFP_KERNEL);
1533 if (pdc->buf == NULL) {
1534 if (i != 0) {
1535 dma_unmap_single(port->dev,
1536 atmel_port->pdc_rx[0].dma_addr,
1537 PDC_BUFFER_SIZE,
1538 DMA_FROM_DEVICE);
1539 kfree(atmel_port->pdc_rx[0].buf);
1540 }
1541 atmel_port->use_pdc_rx = 0;
1542 return -ENOMEM;
1543 }
1544 pdc->dma_addr = dma_map_single(port->dev,
1545 pdc->buf,
1546 PDC_BUFFER_SIZE,
1547 DMA_FROM_DEVICE);
1548 pdc->dma_size = PDC_BUFFER_SIZE;
1549 pdc->ofs = 0;
1550 }
1551
1552 atmel_port->pdc_rx_idx = 0;
1553
1554 atmel_uart_writel(port, ATMEL_PDC_RPR, atmel_port->pdc_rx[0].dma_addr);
1555 atmel_uart_writel(port, ATMEL_PDC_RCR, PDC_BUFFER_SIZE);
1556
1557 atmel_uart_writel(port, ATMEL_PDC_RNPR,
1558 atmel_port->pdc_rx[1].dma_addr);
1559 atmel_uart_writel(port, ATMEL_PDC_RNCR, PDC_BUFFER_SIZE);
1560
1561 return 0;
1562}
1563
1564/*
1565 * tasklet handling tty stuff outside the interrupt handler.
1566 */
1567static void atmel_tasklet_func(unsigned long data)
1568{
1569 struct uart_port *port = (struct uart_port *)data;
1570 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1571 unsigned int status = atmel_port->irq_status;
1572 unsigned int status_change = atmel_port->status_change;
1573
1574 /* The interrupt handler does not take the lock */
1575 spin_lock(&port->lock);
1576
1577 atmel_port->schedule_tx(port);
1578
1579 if (status_change & (ATMEL_US_RI | ATMEL_US_DSR
1580 | ATMEL_US_DCD | ATMEL_US_CTS)) {
1581 /* TODO: All reads to CSR will clear these interrupts! */
1582 if (status_change & ATMEL_US_RI)
1583 port->icount.rng++;
1584 if (status_change & ATMEL_US_DSR)
1585 port->icount.dsr++;
1586 if (status_change & ATMEL_US_DCD)
1587 uart_handle_dcd_change(port, !(status & ATMEL_US_DCD));
1588 if (status_change & ATMEL_US_CTS)
1589 uart_handle_cts_change(port, !(status & ATMEL_US_CTS));
1590
1591 wake_up_interruptible(&port->state->port.delta_msr_wait);
1592
1593 atmel_port->status_change = 0;
1594 }
1595
1596 atmel_port->schedule_rx(port);
1597
1598 spin_unlock(&port->lock);
1599}
1600
1601static void atmel_init_property(struct atmel_uart_port *atmel_port,
1602 struct platform_device *pdev)
1603{
1604 struct device_node *np = pdev->dev.of_node;
1605 struct atmel_uart_data *pdata = dev_get_platdata(&pdev->dev);
1606
1607 if (np) {
1608 /* DMA/PDC usage specification */
1609 if (of_get_property(np, "atmel,use-dma-rx", NULL)) {
1610 if (of_get_property(np, "dmas", NULL)) {
1611 atmel_port->use_dma_rx = true;
1612 atmel_port->use_pdc_rx = false;
1613 } else {
1614 atmel_port->use_dma_rx = false;
1615 atmel_port->use_pdc_rx = true;
1616 }
1617 } else {
1618 atmel_port->use_dma_rx = false;
1619 atmel_port->use_pdc_rx = false;
1620 }
1621
1622 if (of_get_property(np, "atmel,use-dma-tx", NULL)) {
1623 if (of_get_property(np, "dmas", NULL)) {
1624 atmel_port->use_dma_tx = true;
1625 atmel_port->use_pdc_tx = false;
1626 } else {
1627 atmel_port->use_dma_tx = false;
1628 atmel_port->use_pdc_tx = true;
1629 }
1630 } else {
1631 atmel_port->use_dma_tx = false;
1632 atmel_port->use_pdc_tx = false;
1633 }
1634
1635 } else {
1636 atmel_port->use_pdc_rx = pdata->use_dma_rx;
1637 atmel_port->use_pdc_tx = pdata->use_dma_tx;
1638 atmel_port->use_dma_rx = false;
1639 atmel_port->use_dma_tx = false;
1640 }
1641
1642}
1643
1644static void atmel_init_rs485(struct uart_port *port,
1645 struct platform_device *pdev)
1646{
1647 struct device_node *np = pdev->dev.of_node;
1648 struct atmel_uart_data *pdata = dev_get_platdata(&pdev->dev);
1649
1650 if (np) {
1651 struct serial_rs485 *rs485conf = &port->rs485;
1652 u32 rs485_delay[2];
1653 /* rs485 properties */
1654 if (of_property_read_u32_array(np, "rs485-rts-delay",
1655 rs485_delay, 2) == 0) {
1656 rs485conf->delay_rts_before_send = rs485_delay[0];
1657 rs485conf->delay_rts_after_send = rs485_delay[1];
1658 rs485conf->flags = 0;
1659 }
1660
1661 if (of_get_property(np, "rs485-rx-during-tx", NULL))
1662 rs485conf->flags |= SER_RS485_RX_DURING_TX;
1663
1664 if (of_get_property(np, "linux,rs485-enabled-at-boot-time",
1665 NULL))
1666 rs485conf->flags |= SER_RS485_ENABLED;
1667 } else {
1668 port->rs485 = pdata->rs485;
1669 }
1670
1671}
1672
1673static void atmel_set_ops(struct uart_port *port)
1674{
1675 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1676
1677 if (atmel_use_dma_rx(port)) {
1678 atmel_port->prepare_rx = &atmel_prepare_rx_dma;
1679 atmel_port->schedule_rx = &atmel_rx_from_dma;
1680 atmel_port->release_rx = &atmel_release_rx_dma;
1681 } else if (atmel_use_pdc_rx(port)) {
1682 atmel_port->prepare_rx = &atmel_prepare_rx_pdc;
1683 atmel_port->schedule_rx = &atmel_rx_from_pdc;
1684 atmel_port->release_rx = &atmel_release_rx_pdc;
1685 } else {
1686 atmel_port->prepare_rx = NULL;
1687 atmel_port->schedule_rx = &atmel_rx_from_ring;
1688 atmel_port->release_rx = NULL;
1689 }
1690
1691 if (atmel_use_dma_tx(port)) {
1692 atmel_port->prepare_tx = &atmel_prepare_tx_dma;
1693 atmel_port->schedule_tx = &atmel_tx_dma;
1694 atmel_port->release_tx = &atmel_release_tx_dma;
1695 } else if (atmel_use_pdc_tx(port)) {
1696 atmel_port->prepare_tx = &atmel_prepare_tx_pdc;
1697 atmel_port->schedule_tx = &atmel_tx_pdc;
1698 atmel_port->release_tx = &atmel_release_tx_pdc;
1699 } else {
1700 atmel_port->prepare_tx = NULL;
1701 atmel_port->schedule_tx = &atmel_tx_chars;
1702 atmel_port->release_tx = NULL;
1703 }
1704}
1705
1706/*
1707 * Get ip name usart or uart
1708 */
1709static void atmel_get_ip_name(struct uart_port *port)
1710{
1711 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1712 int name = atmel_uart_readl(port, ATMEL_US_NAME);
1713 u32 version;
1714 u32 usart, dbgu_uart, new_uart;
1715 /* ASCII decoding for IP version */
1716 usart = 0x55534152; /* USAR(T) */
1717 dbgu_uart = 0x44424755; /* DBGU */
1718 new_uart = 0x55415254; /* UART */
1719
1720 atmel_port->has_hw_timer = false;
1721
1722 if (name == new_uart) {
1723 dev_dbg(port->dev, "Uart with hw timer");
1724 atmel_port->has_hw_timer = true;
1725 atmel_port->rtor = ATMEL_UA_RTOR;
1726 } else if (name == usart) {
1727 dev_dbg(port->dev, "Usart\n");
1728 atmel_port->has_hw_timer = true;
1729 atmel_port->rtor = ATMEL_US_RTOR;
1730 } else if (name == dbgu_uart) {
1731 dev_dbg(port->dev, "Dbgu or uart without hw timer\n");
1732 } else {
1733 /* fallback for older SoCs: use version field */
1734 version = atmel_uart_readl(port, ATMEL_US_VERSION);
1735 switch (version) {
1736 case 0x302:
1737 case 0x10213:
1738 dev_dbg(port->dev, "This version is usart\n");
1739 atmel_port->has_hw_timer = true;
1740 atmel_port->rtor = ATMEL_US_RTOR;
1741 break;
1742 case 0x203:
1743 case 0x10202:
1744 dev_dbg(port->dev, "This version is uart\n");
1745 break;
1746 default:
1747 dev_err(port->dev, "Not supported ip name nor version, set to uart\n");
1748 }
1749 }
1750}
1751
1752/*
1753 * Perform initialization and enable port for reception
1754 */
1755static int atmel_startup(struct uart_port *port)
1756{
1757 struct platform_device *pdev = to_platform_device(port->dev);
1758 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1759 struct tty_struct *tty = port->state->port.tty;
1760 int retval;
1761
1762 /*
1763 * Ensure that no interrupts are enabled otherwise when
1764 * request_irq() is called we could get stuck trying to
1765 * handle an unexpected interrupt
1766 */
1767 atmel_uart_writel(port, ATMEL_US_IDR, -1);
1768 atmel_port->ms_irq_enabled = false;
1769
1770 /*
1771 * Allocate the IRQ
1772 */
1773 retval = request_irq(port->irq, atmel_interrupt,
1774 IRQF_SHARED | IRQF_COND_SUSPEND,
1775 tty ? tty->name : "atmel_serial", port);
1776 if (retval) {
1777 dev_err(port->dev, "atmel_startup - Can't get irq\n");
1778 return retval;
1779 }
1780
1781 tasklet_enable(&atmel_port->tasklet);
1782
1783 /*
1784 * Initialize DMA (if necessary)
1785 */
1786 atmel_init_property(atmel_port, pdev);
1787 atmel_set_ops(port);
1788
1789 if (atmel_port->prepare_rx) {
1790 retval = atmel_port->prepare_rx(port);
1791 if (retval < 0)
1792 atmel_set_ops(port);
1793 }
1794
1795 if (atmel_port->prepare_tx) {
1796 retval = atmel_port->prepare_tx(port);
1797 if (retval < 0)
1798 atmel_set_ops(port);
1799 }
1800
1801 /*
1802 * Enable FIFO when available
1803 */
1804 if (atmel_port->fifo_size) {
1805 unsigned int txrdym = ATMEL_US_ONE_DATA;
1806 unsigned int rxrdym = ATMEL_US_ONE_DATA;
1807 unsigned int fmr;
1808
1809 atmel_uart_writel(port, ATMEL_US_CR,
1810 ATMEL_US_FIFOEN |
1811 ATMEL_US_RXFCLR |
1812 ATMEL_US_TXFLCLR);
1813
1814 if (atmel_use_dma_tx(port))
1815 txrdym = ATMEL_US_FOUR_DATA;
1816
1817 fmr = ATMEL_US_TXRDYM(txrdym) | ATMEL_US_RXRDYM(rxrdym);
1818 if (atmel_port->rts_high &&
1819 atmel_port->rts_low)
1820 fmr |= ATMEL_US_FRTSC |
1821 ATMEL_US_RXFTHRES(atmel_port->rts_high) |
1822 ATMEL_US_RXFTHRES2(atmel_port->rts_low);
1823
1824 atmel_uart_writel(port, ATMEL_US_FMR, fmr);
1825 }
1826
1827 /* Save current CSR for comparison in atmel_tasklet_func() */
1828 atmel_port->irq_status_prev = atmel_get_lines_status(port);
1829 atmel_port->irq_status = atmel_port->irq_status_prev;
1830
1831 /*
1832 * Finally, enable the serial port
1833 */
1834 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
1835 /* enable xmit & rcvr */
1836 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
1837
1838 setup_timer(&atmel_port->uart_timer,
1839 atmel_uart_timer_callback,
1840 (unsigned long)port);
1841
1842 if (atmel_use_pdc_rx(port)) {
1843 /* set UART timeout */
1844 if (!atmel_port->has_hw_timer) {
1845 mod_timer(&atmel_port->uart_timer,
1846 jiffies + uart_poll_timeout(port));
1847 /* set USART timeout */
1848 } else {
1849 atmel_uart_writel(port, atmel_port->rtor,
1850 PDC_RX_TIMEOUT);
1851 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1852
1853 atmel_uart_writel(port, ATMEL_US_IER,
1854 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
1855 }
1856 /* enable PDC controller */
1857 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
1858 } else if (atmel_use_dma_rx(port)) {
1859 /* set UART timeout */
1860 if (!atmel_port->has_hw_timer) {
1861 mod_timer(&atmel_port->uart_timer,
1862 jiffies + uart_poll_timeout(port));
1863 /* set USART timeout */
1864 } else {
1865 atmel_uart_writel(port, atmel_port->rtor,
1866 PDC_RX_TIMEOUT);
1867 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1868
1869 atmel_uart_writel(port, ATMEL_US_IER,
1870 ATMEL_US_TIMEOUT);
1871 }
1872 } else {
1873 /* enable receive only */
1874 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY);
1875 }
1876
1877 return 0;
1878}
1879
1880/*
1881 * Flush any TX data submitted for DMA. Called when the TX circular
1882 * buffer is reset.
1883 */
1884static void atmel_flush_buffer(struct uart_port *port)
1885{
1886 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1887
1888 if (atmel_use_pdc_tx(port)) {
1889 atmel_uart_writel(port, ATMEL_PDC_TCR, 0);
1890 atmel_port->pdc_tx.ofs = 0;
1891 }
1892}
1893
1894/*
1895 * Disable the port
1896 */
1897static void atmel_shutdown(struct uart_port *port)
1898{
1899 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1900
1901 /*
1902 * Prevent any tasklets being scheduled during
1903 * cleanup
1904 */
1905 del_timer_sync(&atmel_port->uart_timer);
1906
1907 /*
1908 * Clear out any scheduled tasklets before
1909 * we destroy the buffers
1910 */
1911 tasklet_disable(&atmel_port->tasklet);
1912 tasklet_kill(&atmel_port->tasklet);
1913
1914 /*
1915 * Ensure everything is stopped and
1916 * disable all interrupts, port and break condition.
1917 */
1918 atmel_stop_rx(port);
1919 atmel_stop_tx(port);
1920
1921 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
1922 atmel_uart_writel(port, ATMEL_US_IDR, -1);
1923
1924
1925 /*
1926 * Shut-down the DMA.
1927 */
1928 if (atmel_port->release_rx)
1929 atmel_port->release_rx(port);
1930 if (atmel_port->release_tx)
1931 atmel_port->release_tx(port);
1932
1933 /*
1934 * Reset ring buffer pointers
1935 */
1936 atmel_port->rx_ring.head = 0;
1937 atmel_port->rx_ring.tail = 0;
1938
1939 /*
1940 * Free the interrupts
1941 */
1942 free_irq(port->irq, port);
1943
1944 atmel_port->ms_irq_enabled = false;
1945
1946 atmel_flush_buffer(port);
1947}
1948
1949/*
1950 * Power / Clock management.
1951 */
1952static void atmel_serial_pm(struct uart_port *port, unsigned int state,
1953 unsigned int oldstate)
1954{
1955 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1956
1957 switch (state) {
1958 case 0:
1959 /*
1960 * Enable the peripheral clock for this serial port.
1961 * This is called on uart_open() or a resume event.
1962 */
1963 clk_prepare_enable(atmel_port->clk);
1964
1965 /* re-enable interrupts if we disabled some on suspend */
1966 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->backup_imr);
1967 break;
1968 case 3:
1969 /* Back up the interrupt mask and disable all interrupts */
1970 atmel_port->backup_imr = atmel_uart_readl(port, ATMEL_US_IMR);
1971 atmel_uart_writel(port, ATMEL_US_IDR, -1);
1972
1973 /*
1974 * Disable the peripheral clock for this serial port.
1975 * This is called on uart_close() or a suspend event.
1976 */
1977 clk_disable_unprepare(atmel_port->clk);
1978 break;
1979 default:
1980 dev_err(port->dev, "atmel_serial: unknown pm %d\n", state);
1981 }
1982}
1983
1984/*
1985 * Change the port parameters
1986 */
1987static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
1988 struct ktermios *old)
1989{
1990 unsigned long flags;
1991 unsigned int old_mode, mode, imr, quot, baud;
1992
1993 /* save the current mode register */
1994 mode = old_mode = atmel_uart_readl(port, ATMEL_US_MR);
1995
1996 /* reset the mode, clock divisor, parity, stop bits and data size */
1997 mode &= ~(ATMEL_US_USCLKS | ATMEL_US_CHRL | ATMEL_US_NBSTOP |
1998 ATMEL_US_PAR | ATMEL_US_USMODE);
1999
2000 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
2001 quot = uart_get_divisor(port, baud);
2002
2003 if (quot > 65535) { /* BRGR is 16-bit, so switch to slower clock */
2004 quot /= 8;
2005 mode |= ATMEL_US_USCLKS_MCK_DIV8;
2006 }
2007
2008 /* byte size */
2009 switch (termios->c_cflag & CSIZE) {
2010 case CS5:
2011 mode |= ATMEL_US_CHRL_5;
2012 break;
2013 case CS6:
2014 mode |= ATMEL_US_CHRL_6;
2015 break;
2016 case CS7:
2017 mode |= ATMEL_US_CHRL_7;
2018 break;
2019 default:
2020 mode |= ATMEL_US_CHRL_8;
2021 break;
2022 }
2023
2024 /* stop bits */
2025 if (termios->c_cflag & CSTOPB)
2026 mode |= ATMEL_US_NBSTOP_2;
2027
2028 /* parity */
2029 if (termios->c_cflag & PARENB) {
2030 /* Mark or Space parity */
2031 if (termios->c_cflag & CMSPAR) {
2032 if (termios->c_cflag & PARODD)
2033 mode |= ATMEL_US_PAR_MARK;
2034 else
2035 mode |= ATMEL_US_PAR_SPACE;
2036 } else if (termios->c_cflag & PARODD)
2037 mode |= ATMEL_US_PAR_ODD;
2038 else
2039 mode |= ATMEL_US_PAR_EVEN;
2040 } else
2041 mode |= ATMEL_US_PAR_NONE;
2042
2043 spin_lock_irqsave(&port->lock, flags);
2044
2045 port->read_status_mask = ATMEL_US_OVRE;
2046 if (termios->c_iflag & INPCK)
2047 port->read_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE);
2048 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
2049 port->read_status_mask |= ATMEL_US_RXBRK;
2050
2051 if (atmel_use_pdc_rx(port))
2052 /* need to enable error interrupts */
2053 atmel_uart_writel(port, ATMEL_US_IER, port->read_status_mask);
2054
2055 /*
2056 * Characters to ignore
2057 */
2058 port->ignore_status_mask = 0;
2059 if (termios->c_iflag & IGNPAR)
2060 port->ignore_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE);
2061 if (termios->c_iflag & IGNBRK) {
2062 port->ignore_status_mask |= ATMEL_US_RXBRK;
2063 /*
2064 * If we're ignoring parity and break indicators,
2065 * ignore overruns too (for real raw support).
2066 */
2067 if (termios->c_iflag & IGNPAR)
2068 port->ignore_status_mask |= ATMEL_US_OVRE;
2069 }
2070 /* TODO: Ignore all characters if CREAD is set.*/
2071
2072 /* update the per-port timeout */
2073 uart_update_timeout(port, termios->c_cflag, baud);
2074
2075 /*
2076 * save/disable interrupts. The tty layer will ensure that the
2077 * transmitter is empty if requested by the caller, so there's
2078 * no need to wait for it here.
2079 */
2080 imr = atmel_uart_readl(port, ATMEL_US_IMR);
2081 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2082
2083 /* disable receiver and transmitter */
2084 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXDIS);
2085
2086 /* mode */
2087 if (port->rs485.flags & SER_RS485_ENABLED) {
2088 atmel_uart_writel(port, ATMEL_US_TTGR,
2089 port->rs485.delay_rts_after_send);
2090 mode |= ATMEL_US_USMODE_RS485;
2091 } else if (termios->c_cflag & CRTSCTS) {
2092 /* RS232 with hardware handshake (RTS/CTS) */
2093 mode |= ATMEL_US_USMODE_HWHS;
2094 } else {
2095 /* RS232 without hadware handshake */
2096 mode |= ATMEL_US_USMODE_NORMAL;
2097 }
2098
2099 /* set the mode, clock divisor, parity, stop bits and data size */
2100 atmel_uart_writel(port, ATMEL_US_MR, mode);
2101
2102 /*
2103 * when switching the mode, set the RTS line state according to the
2104 * new mode, otherwise keep the former state
2105 */
2106 if ((old_mode & ATMEL_US_USMODE) != (mode & ATMEL_US_USMODE)) {
2107 unsigned int rts_state;
2108
2109 if ((mode & ATMEL_US_USMODE) == ATMEL_US_USMODE_HWHS) {
2110 /* let the hardware control the RTS line */
2111 rts_state = ATMEL_US_RTSDIS;
2112 } else {
2113 /* force RTS line to low level */
2114 rts_state = ATMEL_US_RTSEN;
2115 }
2116
2117 atmel_uart_writel(port, ATMEL_US_CR, rts_state);
2118 }
2119
2120 /* set the baud rate */
2121 atmel_uart_writel(port, ATMEL_US_BRGR, quot);
2122 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
2123 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
2124
2125 /* restore interrupts */
2126 atmel_uart_writel(port, ATMEL_US_IER, imr);
2127
2128 /* CTS flow-control and modem-status interrupts */
2129 if (UART_ENABLE_MS(port, termios->c_cflag))
2130 atmel_enable_ms(port);
2131 else
2132 atmel_disable_ms(port);
2133
2134 spin_unlock_irqrestore(&port->lock, flags);
2135}
2136
2137static void atmel_set_ldisc(struct uart_port *port, struct ktermios *termios)
2138{
2139 if (termios->c_line == N_PPS) {
2140 port->flags |= UPF_HARDPPS_CD;
2141 spin_lock_irq(&port->lock);
2142 atmel_enable_ms(port);
2143 spin_unlock_irq(&port->lock);
2144 } else {
2145 port->flags &= ~UPF_HARDPPS_CD;
2146 if (!UART_ENABLE_MS(port, termios->c_cflag)) {
2147 spin_lock_irq(&port->lock);
2148 atmel_disable_ms(port);
2149 spin_unlock_irq(&port->lock);
2150 }
2151 }
2152}
2153
2154/*
2155 * Return string describing the specified port
2156 */
2157static const char *atmel_type(struct uart_port *port)
2158{
2159 return (port->type == PORT_ATMEL) ? "ATMEL_SERIAL" : NULL;
2160}
2161
2162/*
2163 * Release the memory region(s) being used by 'port'.
2164 */
2165static void atmel_release_port(struct uart_port *port)
2166{
2167 struct platform_device *pdev = to_platform_device(port->dev);
2168 int size = pdev->resource[0].end - pdev->resource[0].start + 1;
2169
2170 release_mem_region(port->mapbase, size);
2171
2172 if (port->flags & UPF_IOREMAP) {
2173 iounmap(port->membase);
2174 port->membase = NULL;
2175 }
2176}
2177
2178/*
2179 * Request the memory region(s) being used by 'port'.
2180 */
2181static int atmel_request_port(struct uart_port *port)
2182{
2183 struct platform_device *pdev = to_platform_device(port->dev);
2184 int size = pdev->resource[0].end - pdev->resource[0].start + 1;
2185
2186 if (!request_mem_region(port->mapbase, size, "atmel_serial"))
2187 return -EBUSY;
2188
2189 if (port->flags & UPF_IOREMAP) {
2190 port->membase = ioremap(port->mapbase, size);
2191 if (port->membase == NULL) {
2192 release_mem_region(port->mapbase, size);
2193 return -ENOMEM;
2194 }
2195 }
2196
2197 return 0;
2198}
2199
2200/*
2201 * Configure/autoconfigure the port.
2202 */
2203static void atmel_config_port(struct uart_port *port, int flags)
2204{
2205 if (flags & UART_CONFIG_TYPE) {
2206 port->type = PORT_ATMEL;
2207 atmel_request_port(port);
2208 }
2209}
2210
2211/*
2212 * Verify the new serial_struct (for TIOCSSERIAL).
2213 */
2214static int atmel_verify_port(struct uart_port *port, struct serial_struct *ser)
2215{
2216 int ret = 0;
2217 if (ser->type != PORT_UNKNOWN && ser->type != PORT_ATMEL)
2218 ret = -EINVAL;
2219 if (port->irq != ser->irq)
2220 ret = -EINVAL;
2221 if (ser->io_type != SERIAL_IO_MEM)
2222 ret = -EINVAL;
2223 if (port->uartclk / 16 != ser->baud_base)
2224 ret = -EINVAL;
2225 if (port->mapbase != (unsigned long)ser->iomem_base)
2226 ret = -EINVAL;
2227 if (port->iobase != ser->port)
2228 ret = -EINVAL;
2229 if (ser->hub6 != 0)
2230 ret = -EINVAL;
2231 return ret;
2232}
2233
2234#ifdef CONFIG_CONSOLE_POLL
2235static int atmel_poll_get_char(struct uart_port *port)
2236{
2237 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_RXRDY))
2238 cpu_relax();
2239
2240 return atmel_uart_read_char(port);
2241}
2242
2243static void atmel_poll_put_char(struct uart_port *port, unsigned char ch)
2244{
2245 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY))
2246 cpu_relax();
2247
2248 atmel_uart_write_char(port, ch);
2249}
2250#endif
2251
2252static struct uart_ops atmel_pops = {
2253 .tx_empty = atmel_tx_empty,
2254 .set_mctrl = atmel_set_mctrl,
2255 .get_mctrl = atmel_get_mctrl,
2256 .stop_tx = atmel_stop_tx,
2257 .start_tx = atmel_start_tx,
2258 .stop_rx = atmel_stop_rx,
2259 .enable_ms = atmel_enable_ms,
2260 .break_ctl = atmel_break_ctl,
2261 .startup = atmel_startup,
2262 .shutdown = atmel_shutdown,
2263 .flush_buffer = atmel_flush_buffer,
2264 .set_termios = atmel_set_termios,
2265 .set_ldisc = atmel_set_ldisc,
2266 .type = atmel_type,
2267 .release_port = atmel_release_port,
2268 .request_port = atmel_request_port,
2269 .config_port = atmel_config_port,
2270 .verify_port = atmel_verify_port,
2271 .pm = atmel_serial_pm,
2272#ifdef CONFIG_CONSOLE_POLL
2273 .poll_get_char = atmel_poll_get_char,
2274 .poll_put_char = atmel_poll_put_char,
2275#endif
2276};
2277
2278/*
2279 * Configure the port from the platform device resource info.
2280 */
2281static int atmel_init_port(struct atmel_uart_port *atmel_port,
2282 struct platform_device *pdev)
2283{
2284 int ret;
2285 struct uart_port *port = &atmel_port->uart;
2286 struct atmel_uart_data *pdata = dev_get_platdata(&pdev->dev);
2287
2288 atmel_init_property(atmel_port, pdev);
2289 atmel_set_ops(port);
2290
2291 atmel_init_rs485(port, pdev);
2292
2293 port->iotype = UPIO_MEM;
2294 port->flags = UPF_BOOT_AUTOCONF;
2295 port->ops = &atmel_pops;
2296 port->fifosize = 1;
2297 port->dev = &pdev->dev;
2298 port->mapbase = pdev->resource[0].start;
2299 port->irq = pdev->resource[1].start;
2300 port->rs485_config = atmel_config_rs485;
2301
2302 tasklet_init(&atmel_port->tasklet, atmel_tasklet_func,
2303 (unsigned long)port);
2304 tasklet_disable(&atmel_port->tasklet);
2305
2306 memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring));
2307
2308 if (pdata && pdata->regs) {
2309 /* Already mapped by setup code */
2310 port->membase = pdata->regs;
2311 } else {
2312 port->flags |= UPF_IOREMAP;
2313 port->membase = NULL;
2314 }
2315
2316 /* for console, the clock could already be configured */
2317 if (!atmel_port->clk) {
2318 atmel_port->clk = clk_get(&pdev->dev, "usart");
2319 if (IS_ERR(atmel_port->clk)) {
2320 ret = PTR_ERR(atmel_port->clk);
2321 atmel_port->clk = NULL;
2322 return ret;
2323 }
2324 ret = clk_prepare_enable(atmel_port->clk);
2325 if (ret) {
2326 clk_put(atmel_port->clk);
2327 atmel_port->clk = NULL;
2328 return ret;
2329 }
2330 port->uartclk = clk_get_rate(atmel_port->clk);
2331 clk_disable_unprepare(atmel_port->clk);
2332 /* only enable clock when USART is in use */
2333 }
2334
2335 /* Use TXEMPTY for interrupt when rs485 else TXRDY or ENDTX|TXBUFE */
2336 if (port->rs485.flags & SER_RS485_ENABLED)
2337 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
2338 else if (atmel_use_pdc_tx(port)) {
2339 port->fifosize = PDC_BUFFER_SIZE;
2340 atmel_port->tx_done_mask = ATMEL_US_ENDTX | ATMEL_US_TXBUFE;
2341 } else {
2342 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
2343 }
2344
2345 return 0;
2346}
2347
2348struct platform_device *atmel_default_console_device; /* the serial console device */
2349
2350#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
2351static void atmel_console_putchar(struct uart_port *port, int ch)
2352{
2353 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY))
2354 cpu_relax();
2355 atmel_uart_write_char(port, ch);
2356}
2357
2358/*
2359 * Interrupts are disabled on entering
2360 */
2361static void atmel_console_write(struct console *co, const char *s, u_int count)
2362{
2363 struct uart_port *port = &atmel_ports[co->index].uart;
2364 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2365 unsigned int status, imr;
2366 unsigned int pdc_tx;
2367
2368 /*
2369 * First, save IMR and then disable interrupts
2370 */
2371 imr = atmel_uart_readl(port, ATMEL_US_IMR);
2372 atmel_uart_writel(port, ATMEL_US_IDR,
2373 ATMEL_US_RXRDY | atmel_port->tx_done_mask);
2374
2375 /* Store PDC transmit status and disable it */
2376 pdc_tx = atmel_uart_readl(port, ATMEL_PDC_PTSR) & ATMEL_PDC_TXTEN;
2377 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
2378
2379 uart_console_write(port, s, count, atmel_console_putchar);
2380
2381 /*
2382 * Finally, wait for transmitter to become empty
2383 * and restore IMR
2384 */
2385 do {
2386 status = atmel_uart_readl(port, ATMEL_US_CSR);
2387 } while (!(status & ATMEL_US_TXRDY));
2388
2389 /* Restore PDC transmit status */
2390 if (pdc_tx)
2391 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
2392
2393 /* set interrupts back the way they were */
2394 atmel_uart_writel(port, ATMEL_US_IER, imr);
2395}
2396
2397/*
2398 * If the port was already initialised (eg, by a boot loader),
2399 * try to determine the current setup.
2400 */
2401static void __init atmel_console_get_options(struct uart_port *port, int *baud,
2402 int *parity, int *bits)
2403{
2404 unsigned int mr, quot;
2405
2406 /*
2407 * If the baud rate generator isn't running, the port wasn't
2408 * initialized by the boot loader.
2409 */
2410 quot = atmel_uart_readl(port, ATMEL_US_BRGR) & ATMEL_US_CD;
2411 if (!quot)
2412 return;
2413
2414 mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_CHRL;
2415 if (mr == ATMEL_US_CHRL_8)
2416 *bits = 8;
2417 else
2418 *bits = 7;
2419
2420 mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_PAR;
2421 if (mr == ATMEL_US_PAR_EVEN)
2422 *parity = 'e';
2423 else if (mr == ATMEL_US_PAR_ODD)
2424 *parity = 'o';
2425
2426 /*
2427 * The serial core only rounds down when matching this to a
2428 * supported baud rate. Make sure we don't end up slightly
2429 * lower than one of those, as it would make us fall through
2430 * to a much lower baud rate than we really want.
2431 */
2432 *baud = port->uartclk / (16 * (quot - 1));
2433}
2434
2435static int __init atmel_console_setup(struct console *co, char *options)
2436{
2437 int ret;
2438 struct uart_port *port = &atmel_ports[co->index].uart;
2439 int baud = 115200;
2440 int bits = 8;
2441 int parity = 'n';
2442 int flow = 'n';
2443
2444 if (port->membase == NULL) {
2445 /* Port not initialized yet - delay setup */
2446 return -ENODEV;
2447 }
2448
2449 ret = clk_prepare_enable(atmel_ports[co->index].clk);
2450 if (ret)
2451 return ret;
2452
2453 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2454 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
2455 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
2456
2457 if (options)
2458 uart_parse_options(options, &baud, &parity, &bits, &flow);
2459 else
2460 atmel_console_get_options(port, &baud, &parity, &bits);
2461
2462 return uart_set_options(port, co, baud, parity, bits, flow);
2463}
2464
2465static struct uart_driver atmel_uart;
2466
2467static struct console atmel_console = {
2468 .name = ATMEL_DEVICENAME,
2469 .write = atmel_console_write,
2470 .device = uart_console_device,
2471 .setup = atmel_console_setup,
2472 .flags = CON_PRINTBUFFER,
2473 .index = -1,
2474 .data = &atmel_uart,
2475};
2476
2477#define ATMEL_CONSOLE_DEVICE (&atmel_console)
2478
2479/*
2480 * Early console initialization (before VM subsystem initialized).
2481 */
2482static int __init atmel_console_init(void)
2483{
2484 int ret;
2485 if (atmel_default_console_device) {
2486 struct atmel_uart_data *pdata =
2487 dev_get_platdata(&atmel_default_console_device->dev);
2488 int id = pdata->num;
2489 struct atmel_uart_port *atmel_port = &atmel_ports[id];
2490
2491 atmel_port->backup_imr = 0;
2492 atmel_port->uart.line = id;
2493
2494 add_preferred_console(ATMEL_DEVICENAME, id, NULL);
2495 ret = atmel_init_port(atmel_port, atmel_default_console_device);
2496 if (ret)
2497 return ret;
2498 register_console(&atmel_console);
2499 }
2500
2501 return 0;
2502}
2503
2504console_initcall(atmel_console_init);
2505
2506/*
2507 * Late console initialization.
2508 */
2509static int __init atmel_late_console_init(void)
2510{
2511 if (atmel_default_console_device
2512 && !(atmel_console.flags & CON_ENABLED))
2513 register_console(&atmel_console);
2514
2515 return 0;
2516}
2517
2518core_initcall(atmel_late_console_init);
2519
2520static inline bool atmel_is_console_port(struct uart_port *port)
2521{
2522 return port->cons && port->cons->index == port->line;
2523}
2524
2525#else
2526#define ATMEL_CONSOLE_DEVICE NULL
2527
2528static inline bool atmel_is_console_port(struct uart_port *port)
2529{
2530 return false;
2531}
2532#endif
2533
2534static struct uart_driver atmel_uart = {
2535 .owner = THIS_MODULE,
2536 .driver_name = "atmel_serial",
2537 .dev_name = ATMEL_DEVICENAME,
2538 .major = SERIAL_ATMEL_MAJOR,
2539 .minor = MINOR_START,
2540 .nr = ATMEL_MAX_UART,
2541 .cons = ATMEL_CONSOLE_DEVICE,
2542};
2543
2544#ifdef CONFIG_PM
2545static bool atmel_serial_clk_will_stop(void)
2546{
2547#ifdef CONFIG_ARCH_AT91
2548 return at91_suspend_entering_slow_clock();
2549#else
2550 return false;
2551#endif
2552}
2553
2554static int atmel_serial_suspend(struct platform_device *pdev,
2555 pm_message_t state)
2556{
2557 struct uart_port *port = platform_get_drvdata(pdev);
2558 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2559
2560 if (atmel_is_console_port(port) && console_suspend_enabled) {
2561 /* Drain the TX shifter */
2562 while (!(atmel_uart_readl(port, ATMEL_US_CSR) &
2563 ATMEL_US_TXEMPTY))
2564 cpu_relax();
2565 }
2566
2567 /* we can not wake up if we're running on slow clock */
2568 atmel_port->may_wakeup = device_may_wakeup(&pdev->dev);
2569 if (atmel_serial_clk_will_stop()) {
2570 unsigned long flags;
2571
2572 spin_lock_irqsave(&atmel_port->lock_suspended, flags);
2573 atmel_port->suspended = true;
2574 spin_unlock_irqrestore(&atmel_port->lock_suspended, flags);
2575 device_set_wakeup_enable(&pdev->dev, 0);
2576 }
2577
2578 uart_suspend_port(&atmel_uart, port);
2579
2580 return 0;
2581}
2582
2583static int atmel_serial_resume(struct platform_device *pdev)
2584{
2585 struct uart_port *port = platform_get_drvdata(pdev);
2586 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2587 unsigned long flags;
2588
2589 spin_lock_irqsave(&atmel_port->lock_suspended, flags);
2590 if (atmel_port->pending) {
2591 atmel_handle_receive(port, atmel_port->pending);
2592 atmel_handle_status(port, atmel_port->pending,
2593 atmel_port->pending_status);
2594 atmel_handle_transmit(port, atmel_port->pending);
2595 atmel_port->pending = 0;
2596 }
2597 atmel_port->suspended = false;
2598 spin_unlock_irqrestore(&atmel_port->lock_suspended, flags);
2599
2600 uart_resume_port(&atmel_uart, port);
2601 device_set_wakeup_enable(&pdev->dev, atmel_port->may_wakeup);
2602
2603 return 0;
2604}
2605#else
2606#define atmel_serial_suspend NULL
2607#define atmel_serial_resume NULL
2608#endif
2609
2610static void atmel_serial_probe_fifos(struct atmel_uart_port *atmel_port,
2611 struct platform_device *pdev)
2612{
2613 atmel_port->fifo_size = 0;
2614 atmel_port->rts_low = 0;
2615 atmel_port->rts_high = 0;
2616
2617 if (of_property_read_u32(pdev->dev.of_node,
2618 "atmel,fifo-size",
2619 &atmel_port->fifo_size))
2620 return;
2621
2622 if (!atmel_port->fifo_size)
2623 return;
2624
2625 if (atmel_port->fifo_size < ATMEL_MIN_FIFO_SIZE) {
2626 atmel_port->fifo_size = 0;
2627 dev_err(&pdev->dev, "Invalid FIFO size\n");
2628 return;
2629 }
2630
2631 /*
2632 * 0 <= rts_low <= rts_high <= fifo_size
2633 * Once their CTS line asserted by the remote peer, some x86 UARTs tend
2634 * to flush their internal TX FIFO, commonly up to 16 data, before
2635 * actually stopping to send new data. So we try to set the RTS High
2636 * Threshold to a reasonably high value respecting this 16 data
2637 * empirical rule when possible.
2638 */
2639 atmel_port->rts_high = max_t(int, atmel_port->fifo_size >> 1,
2640 atmel_port->fifo_size - ATMEL_RTS_HIGH_OFFSET);
2641 atmel_port->rts_low = max_t(int, atmel_port->fifo_size >> 2,
2642 atmel_port->fifo_size - ATMEL_RTS_LOW_OFFSET);
2643
2644 dev_info(&pdev->dev, "Using FIFO (%u data)\n",
2645 atmel_port->fifo_size);
2646 dev_dbg(&pdev->dev, "RTS High Threshold : %2u data\n",
2647 atmel_port->rts_high);
2648 dev_dbg(&pdev->dev, "RTS Low Threshold : %2u data\n",
2649 atmel_port->rts_low);
2650}
2651
2652static int atmel_serial_probe(struct platform_device *pdev)
2653{
2654 struct atmel_uart_port *atmel_port;
2655 struct device_node *np = pdev->dev.of_node;
2656 struct atmel_uart_data *pdata = dev_get_platdata(&pdev->dev);
2657 void *data;
2658 int ret = -ENODEV;
2659 bool rs485_enabled;
2660
2661 BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1));
2662
2663 if (np)
2664 ret = of_alias_get_id(np, "serial");
2665 else
2666 if (pdata)
2667 ret = pdata->num;
2668
2669 if (ret < 0)
2670 /* port id not found in platform data nor device-tree aliases:
2671 * auto-enumerate it */
2672 ret = find_first_zero_bit(atmel_ports_in_use, ATMEL_MAX_UART);
2673
2674 if (ret >= ATMEL_MAX_UART) {
2675 ret = -ENODEV;
2676 goto err;
2677 }
2678
2679 if (test_and_set_bit(ret, atmel_ports_in_use)) {
2680 /* port already in use */
2681 ret = -EBUSY;
2682 goto err;
2683 }
2684
2685 atmel_port = &atmel_ports[ret];
2686 atmel_port->backup_imr = 0;
2687 atmel_port->uart.line = ret;
2688 atmel_serial_probe_fifos(atmel_port, pdev);
2689
2690 spin_lock_init(&atmel_port->lock_suspended);
2691
2692 ret = atmel_init_port(atmel_port, pdev);
2693 if (ret)
2694 goto err_clear_bit;
2695
2696 atmel_port->gpios = mctrl_gpio_init(&atmel_port->uart, 0);
2697 if (IS_ERR(atmel_port->gpios)) {
2698 ret = PTR_ERR(atmel_port->gpios);
2699 goto err_clear_bit;
2700 }
2701
2702 if (!atmel_use_pdc_rx(&atmel_port->uart)) {
2703 ret = -ENOMEM;
2704 data = kmalloc(sizeof(struct atmel_uart_char)
2705 * ATMEL_SERIAL_RINGSIZE, GFP_KERNEL);
2706 if (!data)
2707 goto err_alloc_ring;
2708 atmel_port->rx_ring.buf = data;
2709 }
2710
2711 rs485_enabled = atmel_port->uart.rs485.flags & SER_RS485_ENABLED;
2712
2713 ret = uart_add_one_port(&atmel_uart, &atmel_port->uart);
2714 if (ret)
2715 goto err_add_port;
2716
2717#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
2718 if (atmel_is_console_port(&atmel_port->uart)
2719 && ATMEL_CONSOLE_DEVICE->flags & CON_ENABLED) {
2720 /*
2721 * The serial core enabled the clock for us, so undo
2722 * the clk_prepare_enable() in atmel_console_setup()
2723 */
2724 clk_disable_unprepare(atmel_port->clk);
2725 }
2726#endif
2727
2728 device_init_wakeup(&pdev->dev, 1);
2729 platform_set_drvdata(pdev, atmel_port);
2730
2731 /*
2732 * The peripheral clock has been disabled by atmel_init_port():
2733 * enable it before accessing I/O registers
2734 */
2735 clk_prepare_enable(atmel_port->clk);
2736
2737 if (rs485_enabled) {
2738 atmel_uart_writel(&atmel_port->uart, ATMEL_US_MR,
2739 ATMEL_US_USMODE_NORMAL);
2740 atmel_uart_writel(&atmel_port->uart, ATMEL_US_CR,
2741 ATMEL_US_RTSEN);
2742 }
2743
2744 /*
2745 * Get port name of usart or uart
2746 */
2747 atmel_get_ip_name(&atmel_port->uart);
2748
2749 /*
2750 * The peripheral clock can now safely be disabled till the port
2751 * is used
2752 */
2753 clk_disable_unprepare(atmel_port->clk);
2754
2755 return 0;
2756
2757err_add_port:
2758 kfree(atmel_port->rx_ring.buf);
2759 atmel_port->rx_ring.buf = NULL;
2760err_alloc_ring:
2761 if (!atmel_is_console_port(&atmel_port->uart)) {
2762 clk_put(atmel_port->clk);
2763 atmel_port->clk = NULL;
2764 }
2765err_clear_bit:
2766 clear_bit(atmel_port->uart.line, atmel_ports_in_use);
2767err:
2768 return ret;
2769}
2770
2771/*
2772 * Even if the driver is not modular, it makes sense to be able to
2773 * unbind a device: there can be many bound devices, and there are
2774 * situations where dynamic binding and unbinding can be useful.
2775 *
2776 * For example, a connected device can require a specific firmware update
2777 * protocol that needs bitbanging on IO lines, but use the regular serial
2778 * port in the normal case.
2779 */
2780static int atmel_serial_remove(struct platform_device *pdev)
2781{
2782 struct uart_port *port = platform_get_drvdata(pdev);
2783 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2784 int ret = 0;
2785
2786 tasklet_kill(&atmel_port->tasklet);
2787
2788 device_init_wakeup(&pdev->dev, 0);
2789
2790 ret = uart_remove_one_port(&atmel_uart, port);
2791
2792 kfree(atmel_port->rx_ring.buf);
2793
2794 /* "port" is allocated statically, so we shouldn't free it */
2795
2796 clear_bit(port->line, atmel_ports_in_use);
2797
2798 clk_put(atmel_port->clk);
2799 atmel_port->clk = NULL;
2800
2801 return ret;
2802}
2803
2804static struct platform_driver atmel_serial_driver = {
2805 .probe = atmel_serial_probe,
2806 .remove = atmel_serial_remove,
2807 .suspend = atmel_serial_suspend,
2808 .resume = atmel_serial_resume,
2809 .driver = {
2810 .name = "atmel_usart",
2811 .of_match_table = of_match_ptr(atmel_serial_dt_ids),
2812 },
2813};
2814
2815static int __init atmel_serial_init(void)
2816{
2817 int ret;
2818
2819 ret = uart_register_driver(&atmel_uart);
2820 if (ret)
2821 return ret;
2822
2823 ret = platform_driver_register(&atmel_serial_driver);
2824 if (ret)
2825 uart_unregister_driver(&atmel_uart);
2826
2827 return ret;
2828}
2829device_initcall(atmel_serial_init);
1// SPDX-License-Identifier: GPL-2.0+
2/*
3 * Driver for Atmel AT91 Serial ports
4 * Copyright (C) 2003 Rick Bronson
5 *
6 * Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd.
7 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
8 *
9 * DMA support added by Chip Coldwell.
10 */
11#include <linux/tty.h>
12#include <linux/ioport.h>
13#include <linux/slab.h>
14#include <linux/init.h>
15#include <linux/serial.h>
16#include <linux/clk.h>
17#include <linux/console.h>
18#include <linux/sysrq.h>
19#include <linux/tty_flip.h>
20#include <linux/platform_device.h>
21#include <linux/of.h>
22#include <linux/of_device.h>
23#include <linux/dma-mapping.h>
24#include <linux/dmaengine.h>
25#include <linux/atmel_pdc.h>
26#include <linux/uaccess.h>
27#include <linux/platform_data/atmel.h>
28#include <linux/timer.h>
29#include <linux/err.h>
30#include <linux/irq.h>
31#include <linux/suspend.h>
32#include <linux/mm.h>
33
34#include <asm/div64.h>
35#include <asm/io.h>
36#include <asm/ioctls.h>
37
38#define PDC_BUFFER_SIZE 512
39/* Revisit: We should calculate this based on the actual port settings */
40#define PDC_RX_TIMEOUT (3 * 10) /* 3 bytes */
41
42/* The minium number of data FIFOs should be able to contain */
43#define ATMEL_MIN_FIFO_SIZE 8
44/*
45 * These two offsets are substracted from the RX FIFO size to define the RTS
46 * high and low thresholds
47 */
48#define ATMEL_RTS_HIGH_OFFSET 16
49#define ATMEL_RTS_LOW_OFFSET 20
50
51#include <linux/serial_core.h>
52
53#include "serial_mctrl_gpio.h"
54#include "atmel_serial.h"
55
56static void atmel_start_rx(struct uart_port *port);
57static void atmel_stop_rx(struct uart_port *port);
58
59#ifdef CONFIG_SERIAL_ATMEL_TTYAT
60
61/* Use device name ttyAT, major 204 and minor 154-169. This is necessary if we
62 * should coexist with the 8250 driver, such as if we have an external 16C550
63 * UART. */
64#define SERIAL_ATMEL_MAJOR 204
65#define MINOR_START 154
66#define ATMEL_DEVICENAME "ttyAT"
67
68#else
69
70/* Use device name ttyS, major 4, minor 64-68. This is the usual serial port
71 * name, but it is legally reserved for the 8250 driver. */
72#define SERIAL_ATMEL_MAJOR TTY_MAJOR
73#define MINOR_START 64
74#define ATMEL_DEVICENAME "ttyS"
75
76#endif
77
78#define ATMEL_ISR_PASS_LIMIT 256
79
80struct atmel_dma_buffer {
81 unsigned char *buf;
82 dma_addr_t dma_addr;
83 unsigned int dma_size;
84 unsigned int ofs;
85};
86
87struct atmel_uart_char {
88 u16 status;
89 u16 ch;
90};
91
92/*
93 * Be careful, the real size of the ring buffer is
94 * sizeof(atmel_uart_char) * ATMEL_SERIAL_RINGSIZE. It means that ring buffer
95 * can contain up to 1024 characters in PIO mode and up to 4096 characters in
96 * DMA mode.
97 */
98#define ATMEL_SERIAL_RINGSIZE 1024
99
100/*
101 * at91: 6 USARTs and one DBGU port (SAM9260)
102 * samx7: 3 USARTs and 5 UARTs
103 */
104#define ATMEL_MAX_UART 8
105
106/*
107 * We wrap our port structure around the generic uart_port.
108 */
109struct atmel_uart_port {
110 struct uart_port uart; /* uart */
111 struct clk *clk; /* uart clock */
112 int may_wakeup; /* cached value of device_may_wakeup for times we need to disable it */
113 u32 backup_imr; /* IMR saved during suspend */
114 int break_active; /* break being received */
115
116 bool use_dma_rx; /* enable DMA receiver */
117 bool use_pdc_rx; /* enable PDC receiver */
118 short pdc_rx_idx; /* current PDC RX buffer */
119 struct atmel_dma_buffer pdc_rx[2]; /* PDC receier */
120
121 bool use_dma_tx; /* enable DMA transmitter */
122 bool use_pdc_tx; /* enable PDC transmitter */
123 struct atmel_dma_buffer pdc_tx; /* PDC transmitter */
124
125 spinlock_t lock_tx; /* port lock */
126 spinlock_t lock_rx; /* port lock */
127 struct dma_chan *chan_tx;
128 struct dma_chan *chan_rx;
129 struct dma_async_tx_descriptor *desc_tx;
130 struct dma_async_tx_descriptor *desc_rx;
131 dma_cookie_t cookie_tx;
132 dma_cookie_t cookie_rx;
133 struct scatterlist sg_tx;
134 struct scatterlist sg_rx;
135 struct tasklet_struct tasklet_rx;
136 struct tasklet_struct tasklet_tx;
137 atomic_t tasklet_shutdown;
138 unsigned int irq_status_prev;
139 unsigned int tx_len;
140
141 struct circ_buf rx_ring;
142
143 struct mctrl_gpios *gpios;
144 u32 backup_mode; /* MR saved during iso7816 operations */
145 u32 backup_brgr; /* BRGR saved during iso7816 operations */
146 unsigned int tx_done_mask;
147 u32 fifo_size;
148 u32 rts_high;
149 u32 rts_low;
150 bool ms_irq_enabled;
151 u32 rtor; /* address of receiver timeout register if it exists */
152 bool has_frac_baudrate;
153 bool has_hw_timer;
154 struct timer_list uart_timer;
155
156 bool tx_stopped;
157 bool suspended;
158 unsigned int pending;
159 unsigned int pending_status;
160 spinlock_t lock_suspended;
161
162 bool hd_start_rx; /* can start RX during half-duplex operation */
163
164 /* ISO7816 */
165 unsigned int fidi_min;
166 unsigned int fidi_max;
167
168#ifdef CONFIG_PM
169 struct {
170 u32 cr;
171 u32 mr;
172 u32 imr;
173 u32 brgr;
174 u32 rtor;
175 u32 ttgr;
176 u32 fmr;
177 u32 fimr;
178 } cache;
179#endif
180
181 int (*prepare_rx)(struct uart_port *port);
182 int (*prepare_tx)(struct uart_port *port);
183 void (*schedule_rx)(struct uart_port *port);
184 void (*schedule_tx)(struct uart_port *port);
185 void (*release_rx)(struct uart_port *port);
186 void (*release_tx)(struct uart_port *port);
187};
188
189static struct atmel_uart_port atmel_ports[ATMEL_MAX_UART];
190static DECLARE_BITMAP(atmel_ports_in_use, ATMEL_MAX_UART);
191
192#if defined(CONFIG_OF)
193static const struct of_device_id atmel_serial_dt_ids[] = {
194 { .compatible = "atmel,at91rm9200-usart-serial" },
195 { /* sentinel */ }
196};
197#endif
198
199static inline struct atmel_uart_port *
200to_atmel_uart_port(struct uart_port *uart)
201{
202 return container_of(uart, struct atmel_uart_port, uart);
203}
204
205static inline u32 atmel_uart_readl(struct uart_port *port, u32 reg)
206{
207 return __raw_readl(port->membase + reg);
208}
209
210static inline void atmel_uart_writel(struct uart_port *port, u32 reg, u32 value)
211{
212 __raw_writel(value, port->membase + reg);
213}
214
215static inline u8 atmel_uart_read_char(struct uart_port *port)
216{
217 return __raw_readb(port->membase + ATMEL_US_RHR);
218}
219
220static inline void atmel_uart_write_char(struct uart_port *port, u8 value)
221{
222 __raw_writeb(value, port->membase + ATMEL_US_THR);
223}
224
225static inline int atmel_uart_is_half_duplex(struct uart_port *port)
226{
227 return ((port->rs485.flags & SER_RS485_ENABLED) &&
228 !(port->rs485.flags & SER_RS485_RX_DURING_TX)) ||
229 (port->iso7816.flags & SER_ISO7816_ENABLED);
230}
231
232#ifdef CONFIG_SERIAL_ATMEL_PDC
233static bool atmel_use_pdc_rx(struct uart_port *port)
234{
235 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
236
237 return atmel_port->use_pdc_rx;
238}
239
240static bool atmel_use_pdc_tx(struct uart_port *port)
241{
242 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
243
244 return atmel_port->use_pdc_tx;
245}
246#else
247static bool atmel_use_pdc_rx(struct uart_port *port)
248{
249 return false;
250}
251
252static bool atmel_use_pdc_tx(struct uart_port *port)
253{
254 return false;
255}
256#endif
257
258static bool atmel_use_dma_tx(struct uart_port *port)
259{
260 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
261
262 return atmel_port->use_dma_tx;
263}
264
265static bool atmel_use_dma_rx(struct uart_port *port)
266{
267 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
268
269 return atmel_port->use_dma_rx;
270}
271
272static bool atmel_use_fifo(struct uart_port *port)
273{
274 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
275
276 return atmel_port->fifo_size;
277}
278
279static void atmel_tasklet_schedule(struct atmel_uart_port *atmel_port,
280 struct tasklet_struct *t)
281{
282 if (!atomic_read(&atmel_port->tasklet_shutdown))
283 tasklet_schedule(t);
284}
285
286/* Enable or disable the rs485 support */
287static int atmel_config_rs485(struct uart_port *port,
288 struct serial_rs485 *rs485conf)
289{
290 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
291 unsigned int mode;
292
293 /* Disable interrupts */
294 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
295
296 mode = atmel_uart_readl(port, ATMEL_US_MR);
297
298 /* Resetting serial mode to RS232 (0x0) */
299 mode &= ~ATMEL_US_USMODE;
300
301 port->rs485 = *rs485conf;
302
303 if (rs485conf->flags & SER_RS485_ENABLED) {
304 dev_dbg(port->dev, "Setting UART to RS485\n");
305 if (port->rs485.flags & SER_RS485_RX_DURING_TX)
306 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
307 else
308 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
309
310 atmel_uart_writel(port, ATMEL_US_TTGR,
311 rs485conf->delay_rts_after_send);
312 mode |= ATMEL_US_USMODE_RS485;
313 } else {
314 dev_dbg(port->dev, "Setting UART to RS232\n");
315 if (atmel_use_pdc_tx(port))
316 atmel_port->tx_done_mask = ATMEL_US_ENDTX |
317 ATMEL_US_TXBUFE;
318 else
319 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
320 }
321 atmel_uart_writel(port, ATMEL_US_MR, mode);
322
323 /* Enable interrupts */
324 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
325
326 return 0;
327}
328
329static unsigned int atmel_calc_cd(struct uart_port *port,
330 struct serial_iso7816 *iso7816conf)
331{
332 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
333 unsigned int cd;
334 u64 mck_rate;
335
336 mck_rate = (u64)clk_get_rate(atmel_port->clk);
337 do_div(mck_rate, iso7816conf->clk);
338 cd = mck_rate;
339 return cd;
340}
341
342static unsigned int atmel_calc_fidi(struct uart_port *port,
343 struct serial_iso7816 *iso7816conf)
344{
345 u64 fidi = 0;
346
347 if (iso7816conf->sc_fi && iso7816conf->sc_di) {
348 fidi = (u64)iso7816conf->sc_fi;
349 do_div(fidi, iso7816conf->sc_di);
350 }
351 return (u32)fidi;
352}
353
354/* Enable or disable the iso7816 support */
355/* Called with interrupts disabled */
356static int atmel_config_iso7816(struct uart_port *port,
357 struct serial_iso7816 *iso7816conf)
358{
359 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
360 unsigned int mode;
361 unsigned int cd, fidi;
362 int ret = 0;
363
364 /* Disable interrupts */
365 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
366
367 mode = atmel_uart_readl(port, ATMEL_US_MR);
368
369 if (iso7816conf->flags & SER_ISO7816_ENABLED) {
370 mode &= ~ATMEL_US_USMODE;
371
372 if (iso7816conf->tg > 255) {
373 dev_err(port->dev, "ISO7816: Timeguard exceeding 255\n");
374 memset(iso7816conf, 0, sizeof(struct serial_iso7816));
375 ret = -EINVAL;
376 goto err_out;
377 }
378
379 if ((iso7816conf->flags & SER_ISO7816_T_PARAM)
380 == SER_ISO7816_T(0)) {
381 mode |= ATMEL_US_USMODE_ISO7816_T0 | ATMEL_US_DSNACK;
382 } else if ((iso7816conf->flags & SER_ISO7816_T_PARAM)
383 == SER_ISO7816_T(1)) {
384 mode |= ATMEL_US_USMODE_ISO7816_T1 | ATMEL_US_INACK;
385 } else {
386 dev_err(port->dev, "ISO7816: Type not supported\n");
387 memset(iso7816conf, 0, sizeof(struct serial_iso7816));
388 ret = -EINVAL;
389 goto err_out;
390 }
391
392 mode &= ~(ATMEL_US_USCLKS | ATMEL_US_NBSTOP | ATMEL_US_PAR);
393
394 /* select mck clock, and output */
395 mode |= ATMEL_US_USCLKS_MCK | ATMEL_US_CLKO;
396 /* set parity for normal/inverse mode + max iterations */
397 mode |= ATMEL_US_PAR_EVEN | ATMEL_US_NBSTOP_1 | ATMEL_US_MAX_ITER(3);
398
399 cd = atmel_calc_cd(port, iso7816conf);
400 fidi = atmel_calc_fidi(port, iso7816conf);
401 if (fidi == 0) {
402 dev_warn(port->dev, "ISO7816 fidi = 0, Generator generates no signal\n");
403 } else if (fidi < atmel_port->fidi_min
404 || fidi > atmel_port->fidi_max) {
405 dev_err(port->dev, "ISO7816 fidi = %u, value not supported\n", fidi);
406 memset(iso7816conf, 0, sizeof(struct serial_iso7816));
407 ret = -EINVAL;
408 goto err_out;
409 }
410
411 if (!(port->iso7816.flags & SER_ISO7816_ENABLED)) {
412 /* port not yet in iso7816 mode: store configuration */
413 atmel_port->backup_mode = atmel_uart_readl(port, ATMEL_US_MR);
414 atmel_port->backup_brgr = atmel_uart_readl(port, ATMEL_US_BRGR);
415 }
416
417 atmel_uart_writel(port, ATMEL_US_TTGR, iso7816conf->tg);
418 atmel_uart_writel(port, ATMEL_US_BRGR, cd);
419 atmel_uart_writel(port, ATMEL_US_FIDI, fidi);
420
421 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXEN);
422 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY | ATMEL_US_NACK | ATMEL_US_ITERATION;
423 } else {
424 dev_dbg(port->dev, "Setting UART back to RS232\n");
425 /* back to last RS232 settings */
426 mode = atmel_port->backup_mode;
427 memset(iso7816conf, 0, sizeof(struct serial_iso7816));
428 atmel_uart_writel(port, ATMEL_US_TTGR, 0);
429 atmel_uart_writel(port, ATMEL_US_BRGR, atmel_port->backup_brgr);
430 atmel_uart_writel(port, ATMEL_US_FIDI, 0x174);
431
432 if (atmel_use_pdc_tx(port))
433 atmel_port->tx_done_mask = ATMEL_US_ENDTX |
434 ATMEL_US_TXBUFE;
435 else
436 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
437 }
438
439 port->iso7816 = *iso7816conf;
440
441 atmel_uart_writel(port, ATMEL_US_MR, mode);
442
443err_out:
444 /* Enable interrupts */
445 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
446
447 return ret;
448}
449
450/*
451 * Return TIOCSER_TEMT when transmitter FIFO and Shift register is empty.
452 */
453static u_int atmel_tx_empty(struct uart_port *port)
454{
455 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
456
457 if (atmel_port->tx_stopped)
458 return TIOCSER_TEMT;
459 return (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXEMPTY) ?
460 TIOCSER_TEMT :
461 0;
462}
463
464/*
465 * Set state of the modem control output lines
466 */
467static void atmel_set_mctrl(struct uart_port *port, u_int mctrl)
468{
469 unsigned int control = 0;
470 unsigned int mode = atmel_uart_readl(port, ATMEL_US_MR);
471 unsigned int rts_paused, rts_ready;
472 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
473
474 /* override mode to RS485 if needed, otherwise keep the current mode */
475 if (port->rs485.flags & SER_RS485_ENABLED) {
476 atmel_uart_writel(port, ATMEL_US_TTGR,
477 port->rs485.delay_rts_after_send);
478 mode &= ~ATMEL_US_USMODE;
479 mode |= ATMEL_US_USMODE_RS485;
480 }
481
482 /* set the RTS line state according to the mode */
483 if ((mode & ATMEL_US_USMODE) == ATMEL_US_USMODE_HWHS) {
484 /* force RTS line to high level */
485 rts_paused = ATMEL_US_RTSEN;
486
487 /* give the control of the RTS line back to the hardware */
488 rts_ready = ATMEL_US_RTSDIS;
489 } else {
490 /* force RTS line to high level */
491 rts_paused = ATMEL_US_RTSDIS;
492
493 /* force RTS line to low level */
494 rts_ready = ATMEL_US_RTSEN;
495 }
496
497 if (mctrl & TIOCM_RTS)
498 control |= rts_ready;
499 else
500 control |= rts_paused;
501
502 if (mctrl & TIOCM_DTR)
503 control |= ATMEL_US_DTREN;
504 else
505 control |= ATMEL_US_DTRDIS;
506
507 atmel_uart_writel(port, ATMEL_US_CR, control);
508
509 mctrl_gpio_set(atmel_port->gpios, mctrl);
510
511 /* Local loopback mode? */
512 mode &= ~ATMEL_US_CHMODE;
513 if (mctrl & TIOCM_LOOP)
514 mode |= ATMEL_US_CHMODE_LOC_LOOP;
515 else
516 mode |= ATMEL_US_CHMODE_NORMAL;
517
518 atmel_uart_writel(port, ATMEL_US_MR, mode);
519}
520
521/*
522 * Get state of the modem control input lines
523 */
524static u_int atmel_get_mctrl(struct uart_port *port)
525{
526 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
527 unsigned int ret = 0, status;
528
529 status = atmel_uart_readl(port, ATMEL_US_CSR);
530
531 /*
532 * The control signals are active low.
533 */
534 if (!(status & ATMEL_US_DCD))
535 ret |= TIOCM_CD;
536 if (!(status & ATMEL_US_CTS))
537 ret |= TIOCM_CTS;
538 if (!(status & ATMEL_US_DSR))
539 ret |= TIOCM_DSR;
540 if (!(status & ATMEL_US_RI))
541 ret |= TIOCM_RI;
542
543 return mctrl_gpio_get(atmel_port->gpios, &ret);
544}
545
546/*
547 * Stop transmitting.
548 */
549static void atmel_stop_tx(struct uart_port *port)
550{
551 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
552
553 if (atmel_use_pdc_tx(port)) {
554 /* disable PDC transmit */
555 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
556 }
557
558 /*
559 * Disable the transmitter.
560 * This is mandatory when DMA is used, otherwise the DMA buffer
561 * is fully transmitted.
562 */
563 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS);
564 atmel_port->tx_stopped = true;
565
566 /* Disable interrupts */
567 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
568
569 if (atmel_uart_is_half_duplex(port))
570 if (!atomic_read(&atmel_port->tasklet_shutdown))
571 atmel_start_rx(port);
572
573}
574
575/*
576 * Start transmitting.
577 */
578static void atmel_start_tx(struct uart_port *port)
579{
580 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
581
582 if (atmel_use_pdc_tx(port) && (atmel_uart_readl(port, ATMEL_PDC_PTSR)
583 & ATMEL_PDC_TXTEN))
584 /* The transmitter is already running. Yes, we
585 really need this.*/
586 return;
587
588 if (atmel_use_pdc_tx(port) || atmel_use_dma_tx(port))
589 if (atmel_uart_is_half_duplex(port))
590 atmel_stop_rx(port);
591
592 if (atmel_use_pdc_tx(port))
593 /* re-enable PDC transmit */
594 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
595
596 /* Enable interrupts */
597 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
598
599 /* re-enable the transmitter */
600 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN);
601 atmel_port->tx_stopped = false;
602}
603
604/*
605 * start receiving - port is in process of being opened.
606 */
607static void atmel_start_rx(struct uart_port *port)
608{
609 /* reset status and receiver */
610 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
611
612 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXEN);
613
614 if (atmel_use_pdc_rx(port)) {
615 /* enable PDC controller */
616 atmel_uart_writel(port, ATMEL_US_IER,
617 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
618 port->read_status_mask);
619 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
620 } else {
621 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY);
622 }
623}
624
625/*
626 * Stop receiving - port is in process of being closed.
627 */
628static void atmel_stop_rx(struct uart_port *port)
629{
630 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXDIS);
631
632 if (atmel_use_pdc_rx(port)) {
633 /* disable PDC receive */
634 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS);
635 atmel_uart_writel(port, ATMEL_US_IDR,
636 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
637 port->read_status_mask);
638 } else {
639 atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXRDY);
640 }
641}
642
643/*
644 * Enable modem status interrupts
645 */
646static void atmel_enable_ms(struct uart_port *port)
647{
648 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
649 uint32_t ier = 0;
650
651 /*
652 * Interrupt should not be enabled twice
653 */
654 if (atmel_port->ms_irq_enabled)
655 return;
656
657 atmel_port->ms_irq_enabled = true;
658
659 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
660 ier |= ATMEL_US_CTSIC;
661
662 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DSR))
663 ier |= ATMEL_US_DSRIC;
664
665 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_RI))
666 ier |= ATMEL_US_RIIC;
667
668 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DCD))
669 ier |= ATMEL_US_DCDIC;
670
671 atmel_uart_writel(port, ATMEL_US_IER, ier);
672
673 mctrl_gpio_enable_ms(atmel_port->gpios);
674}
675
676/*
677 * Disable modem status interrupts
678 */
679static void atmel_disable_ms(struct uart_port *port)
680{
681 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
682 uint32_t idr = 0;
683
684 /*
685 * Interrupt should not be disabled twice
686 */
687 if (!atmel_port->ms_irq_enabled)
688 return;
689
690 atmel_port->ms_irq_enabled = false;
691
692 mctrl_gpio_disable_ms(atmel_port->gpios);
693
694 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
695 idr |= ATMEL_US_CTSIC;
696
697 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DSR))
698 idr |= ATMEL_US_DSRIC;
699
700 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_RI))
701 idr |= ATMEL_US_RIIC;
702
703 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DCD))
704 idr |= ATMEL_US_DCDIC;
705
706 atmel_uart_writel(port, ATMEL_US_IDR, idr);
707}
708
709/*
710 * Control the transmission of a break signal
711 */
712static void atmel_break_ctl(struct uart_port *port, int break_state)
713{
714 if (break_state != 0)
715 /* start break */
716 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTBRK);
717 else
718 /* stop break */
719 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STPBRK);
720}
721
722/*
723 * Stores the incoming character in the ring buffer
724 */
725static void
726atmel_buffer_rx_char(struct uart_port *port, unsigned int status,
727 unsigned int ch)
728{
729 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
730 struct circ_buf *ring = &atmel_port->rx_ring;
731 struct atmel_uart_char *c;
732
733 if (!CIRC_SPACE(ring->head, ring->tail, ATMEL_SERIAL_RINGSIZE))
734 /* Buffer overflow, ignore char */
735 return;
736
737 c = &((struct atmel_uart_char *)ring->buf)[ring->head];
738 c->status = status;
739 c->ch = ch;
740
741 /* Make sure the character is stored before we update head. */
742 smp_wmb();
743
744 ring->head = (ring->head + 1) & (ATMEL_SERIAL_RINGSIZE - 1);
745}
746
747/*
748 * Deal with parity, framing and overrun errors.
749 */
750static void atmel_pdc_rxerr(struct uart_port *port, unsigned int status)
751{
752 /* clear error */
753 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
754
755 if (status & ATMEL_US_RXBRK) {
756 /* ignore side-effect */
757 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);
758 port->icount.brk++;
759 }
760 if (status & ATMEL_US_PARE)
761 port->icount.parity++;
762 if (status & ATMEL_US_FRAME)
763 port->icount.frame++;
764 if (status & ATMEL_US_OVRE)
765 port->icount.overrun++;
766}
767
768/*
769 * Characters received (called from interrupt handler)
770 */
771static void atmel_rx_chars(struct uart_port *port)
772{
773 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
774 unsigned int status, ch;
775
776 status = atmel_uart_readl(port, ATMEL_US_CSR);
777 while (status & ATMEL_US_RXRDY) {
778 ch = atmel_uart_read_char(port);
779
780 /*
781 * note that the error handling code is
782 * out of the main execution path
783 */
784 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME
785 | ATMEL_US_OVRE | ATMEL_US_RXBRK)
786 || atmel_port->break_active)) {
787
788 /* clear error */
789 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
790
791 if (status & ATMEL_US_RXBRK
792 && !atmel_port->break_active) {
793 atmel_port->break_active = 1;
794 atmel_uart_writel(port, ATMEL_US_IER,
795 ATMEL_US_RXBRK);
796 } else {
797 /*
798 * This is either the end-of-break
799 * condition or we've received at
800 * least one character without RXBRK
801 * being set. In both cases, the next
802 * RXBRK will indicate start-of-break.
803 */
804 atmel_uart_writel(port, ATMEL_US_IDR,
805 ATMEL_US_RXBRK);
806 status &= ~ATMEL_US_RXBRK;
807 atmel_port->break_active = 0;
808 }
809 }
810
811 atmel_buffer_rx_char(port, status, ch);
812 status = atmel_uart_readl(port, ATMEL_US_CSR);
813 }
814
815 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx);
816}
817
818/*
819 * Transmit characters (called from tasklet with TXRDY interrupt
820 * disabled)
821 */
822static void atmel_tx_chars(struct uart_port *port)
823{
824 struct circ_buf *xmit = &port->state->xmit;
825 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
826
827 if (port->x_char &&
828 (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY)) {
829 atmel_uart_write_char(port, port->x_char);
830 port->icount.tx++;
831 port->x_char = 0;
832 }
833 if (uart_circ_empty(xmit) || uart_tx_stopped(port))
834 return;
835
836 while (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY) {
837 atmel_uart_write_char(port, xmit->buf[xmit->tail]);
838 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
839 port->icount.tx++;
840 if (uart_circ_empty(xmit))
841 break;
842 }
843
844 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
845 uart_write_wakeup(port);
846
847 if (!uart_circ_empty(xmit)) {
848 /* we still have characters to transmit, so we should continue
849 * transmitting them when TX is ready, regardless of
850 * mode or duplexity
851 */
852 atmel_port->tx_done_mask |= ATMEL_US_TXRDY;
853
854 /* Enable interrupts */
855 atmel_uart_writel(port, ATMEL_US_IER,
856 atmel_port->tx_done_mask);
857 } else {
858 if (atmel_uart_is_half_duplex(port))
859 atmel_port->tx_done_mask &= ~ATMEL_US_TXRDY;
860 }
861}
862
863static void atmel_complete_tx_dma(void *arg)
864{
865 struct atmel_uart_port *atmel_port = arg;
866 struct uart_port *port = &atmel_port->uart;
867 struct circ_buf *xmit = &port->state->xmit;
868 struct dma_chan *chan = atmel_port->chan_tx;
869 unsigned long flags;
870
871 spin_lock_irqsave(&port->lock, flags);
872
873 if (chan)
874 dmaengine_terminate_all(chan);
875 xmit->tail += atmel_port->tx_len;
876 xmit->tail &= UART_XMIT_SIZE - 1;
877
878 port->icount.tx += atmel_port->tx_len;
879
880 spin_lock_irq(&atmel_port->lock_tx);
881 async_tx_ack(atmel_port->desc_tx);
882 atmel_port->cookie_tx = -EINVAL;
883 atmel_port->desc_tx = NULL;
884 spin_unlock_irq(&atmel_port->lock_tx);
885
886 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
887 uart_write_wakeup(port);
888
889 /*
890 * xmit is a circular buffer so, if we have just send data from
891 * xmit->tail to the end of xmit->buf, now we have to transmit the
892 * remaining data from the beginning of xmit->buf to xmit->head.
893 */
894 if (!uart_circ_empty(xmit))
895 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
896 else if (atmel_uart_is_half_duplex(port)) {
897 /*
898 * DMA done, re-enable TXEMPTY and signal that we can stop
899 * TX and start RX for RS485
900 */
901 atmel_port->hd_start_rx = true;
902 atmel_uart_writel(port, ATMEL_US_IER,
903 atmel_port->tx_done_mask);
904 }
905
906 spin_unlock_irqrestore(&port->lock, flags);
907}
908
909static void atmel_release_tx_dma(struct uart_port *port)
910{
911 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
912 struct dma_chan *chan = atmel_port->chan_tx;
913
914 if (chan) {
915 dmaengine_terminate_all(chan);
916 dma_release_channel(chan);
917 dma_unmap_sg(port->dev, &atmel_port->sg_tx, 1,
918 DMA_TO_DEVICE);
919 }
920
921 atmel_port->desc_tx = NULL;
922 atmel_port->chan_tx = NULL;
923 atmel_port->cookie_tx = -EINVAL;
924}
925
926/*
927 * Called from tasklet with TXRDY interrupt is disabled.
928 */
929static void atmel_tx_dma(struct uart_port *port)
930{
931 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
932 struct circ_buf *xmit = &port->state->xmit;
933 struct dma_chan *chan = atmel_port->chan_tx;
934 struct dma_async_tx_descriptor *desc;
935 struct scatterlist sgl[2], *sg, *sg_tx = &atmel_port->sg_tx;
936 unsigned int tx_len, part1_len, part2_len, sg_len;
937 dma_addr_t phys_addr;
938
939 /* Make sure we have an idle channel */
940 if (atmel_port->desc_tx != NULL)
941 return;
942
943 if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) {
944 /*
945 * DMA is idle now.
946 * Port xmit buffer is already mapped,
947 * and it is one page... Just adjust
948 * offsets and lengths. Since it is a circular buffer,
949 * we have to transmit till the end, and then the rest.
950 * Take the port lock to get a
951 * consistent xmit buffer state.
952 */
953 tx_len = CIRC_CNT_TO_END(xmit->head,
954 xmit->tail,
955 UART_XMIT_SIZE);
956
957 if (atmel_port->fifo_size) {
958 /* multi data mode */
959 part1_len = (tx_len & ~0x3); /* DWORD access */
960 part2_len = (tx_len & 0x3); /* BYTE access */
961 } else {
962 /* single data (legacy) mode */
963 part1_len = 0;
964 part2_len = tx_len; /* BYTE access only */
965 }
966
967 sg_init_table(sgl, 2);
968 sg_len = 0;
969 phys_addr = sg_dma_address(sg_tx) + xmit->tail;
970 if (part1_len) {
971 sg = &sgl[sg_len++];
972 sg_dma_address(sg) = phys_addr;
973 sg_dma_len(sg) = part1_len;
974
975 phys_addr += part1_len;
976 }
977
978 if (part2_len) {
979 sg = &sgl[sg_len++];
980 sg_dma_address(sg) = phys_addr;
981 sg_dma_len(sg) = part2_len;
982 }
983
984 /*
985 * save tx_len so atmel_complete_tx_dma() will increase
986 * xmit->tail correctly
987 */
988 atmel_port->tx_len = tx_len;
989
990 desc = dmaengine_prep_slave_sg(chan,
991 sgl,
992 sg_len,
993 DMA_MEM_TO_DEV,
994 DMA_PREP_INTERRUPT |
995 DMA_CTRL_ACK);
996 if (!desc) {
997 dev_err(port->dev, "Failed to send via dma!\n");
998 return;
999 }
1000
1001 dma_sync_sg_for_device(port->dev, sg_tx, 1, DMA_TO_DEVICE);
1002
1003 atmel_port->desc_tx = desc;
1004 desc->callback = atmel_complete_tx_dma;
1005 desc->callback_param = atmel_port;
1006 atmel_port->cookie_tx = dmaengine_submit(desc);
1007 }
1008
1009 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
1010 uart_write_wakeup(port);
1011}
1012
1013static int atmel_prepare_tx_dma(struct uart_port *port)
1014{
1015 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1016 struct device *mfd_dev = port->dev->parent;
1017 dma_cap_mask_t mask;
1018 struct dma_slave_config config;
1019 int ret, nent;
1020
1021 dma_cap_zero(mask);
1022 dma_cap_set(DMA_SLAVE, mask);
1023
1024 atmel_port->chan_tx = dma_request_slave_channel(mfd_dev, "tx");
1025 if (atmel_port->chan_tx == NULL)
1026 goto chan_err;
1027 dev_info(port->dev, "using %s for tx DMA transfers\n",
1028 dma_chan_name(atmel_port->chan_tx));
1029
1030 spin_lock_init(&atmel_port->lock_tx);
1031 sg_init_table(&atmel_port->sg_tx, 1);
1032 /* UART circular tx buffer is an aligned page. */
1033 BUG_ON(!PAGE_ALIGNED(port->state->xmit.buf));
1034 sg_set_page(&atmel_port->sg_tx,
1035 virt_to_page(port->state->xmit.buf),
1036 UART_XMIT_SIZE,
1037 offset_in_page(port->state->xmit.buf));
1038 nent = dma_map_sg(port->dev,
1039 &atmel_port->sg_tx,
1040 1,
1041 DMA_TO_DEVICE);
1042
1043 if (!nent) {
1044 dev_dbg(port->dev, "need to release resource of dma\n");
1045 goto chan_err;
1046 } else {
1047 dev_dbg(port->dev, "%s: mapped %d@%p to %pad\n", __func__,
1048 sg_dma_len(&atmel_port->sg_tx),
1049 port->state->xmit.buf,
1050 &sg_dma_address(&atmel_port->sg_tx));
1051 }
1052
1053 /* Configure the slave DMA */
1054 memset(&config, 0, sizeof(config));
1055 config.direction = DMA_MEM_TO_DEV;
1056 config.dst_addr_width = (atmel_port->fifo_size) ?
1057 DMA_SLAVE_BUSWIDTH_4_BYTES :
1058 DMA_SLAVE_BUSWIDTH_1_BYTE;
1059 config.dst_addr = port->mapbase + ATMEL_US_THR;
1060 config.dst_maxburst = 1;
1061
1062 ret = dmaengine_slave_config(atmel_port->chan_tx,
1063 &config);
1064 if (ret) {
1065 dev_err(port->dev, "DMA tx slave configuration failed\n");
1066 goto chan_err;
1067 }
1068
1069 return 0;
1070
1071chan_err:
1072 dev_err(port->dev, "TX channel not available, switch to pio\n");
1073 atmel_port->use_dma_tx = false;
1074 if (atmel_port->chan_tx)
1075 atmel_release_tx_dma(port);
1076 return -EINVAL;
1077}
1078
1079static void atmel_complete_rx_dma(void *arg)
1080{
1081 struct uart_port *port = arg;
1082 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1083
1084 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx);
1085}
1086
1087static void atmel_release_rx_dma(struct uart_port *port)
1088{
1089 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1090 struct dma_chan *chan = atmel_port->chan_rx;
1091
1092 if (chan) {
1093 dmaengine_terminate_all(chan);
1094 dma_release_channel(chan);
1095 dma_unmap_sg(port->dev, &atmel_port->sg_rx, 1,
1096 DMA_FROM_DEVICE);
1097 }
1098
1099 atmel_port->desc_rx = NULL;
1100 atmel_port->chan_rx = NULL;
1101 atmel_port->cookie_rx = -EINVAL;
1102}
1103
1104static void atmel_rx_from_dma(struct uart_port *port)
1105{
1106 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1107 struct tty_port *tport = &port->state->port;
1108 struct circ_buf *ring = &atmel_port->rx_ring;
1109 struct dma_chan *chan = atmel_port->chan_rx;
1110 struct dma_tx_state state;
1111 enum dma_status dmastat;
1112 size_t count;
1113
1114
1115 /* Reset the UART timeout early so that we don't miss one */
1116 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1117 dmastat = dmaengine_tx_status(chan,
1118 atmel_port->cookie_rx,
1119 &state);
1120 /* Restart a new tasklet if DMA status is error */
1121 if (dmastat == DMA_ERROR) {
1122 dev_dbg(port->dev, "Get residue error, restart tasklet\n");
1123 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT);
1124 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx);
1125 return;
1126 }
1127
1128 /* CPU claims ownership of RX DMA buffer */
1129 dma_sync_sg_for_cpu(port->dev,
1130 &atmel_port->sg_rx,
1131 1,
1132 DMA_FROM_DEVICE);
1133
1134 /*
1135 * ring->head points to the end of data already written by the DMA.
1136 * ring->tail points to the beginning of data to be read by the
1137 * framework.
1138 * The current transfer size should not be larger than the dma buffer
1139 * length.
1140 */
1141 ring->head = sg_dma_len(&atmel_port->sg_rx) - state.residue;
1142 BUG_ON(ring->head > sg_dma_len(&atmel_port->sg_rx));
1143 /*
1144 * At this point ring->head may point to the first byte right after the
1145 * last byte of the dma buffer:
1146 * 0 <= ring->head <= sg_dma_len(&atmel_port->sg_rx)
1147 *
1148 * However ring->tail must always points inside the dma buffer:
1149 * 0 <= ring->tail <= sg_dma_len(&atmel_port->sg_rx) - 1
1150 *
1151 * Since we use a ring buffer, we have to handle the case
1152 * where head is lower than tail. In such a case, we first read from
1153 * tail to the end of the buffer then reset tail.
1154 */
1155 if (ring->head < ring->tail) {
1156 count = sg_dma_len(&atmel_port->sg_rx) - ring->tail;
1157
1158 tty_insert_flip_string(tport, ring->buf + ring->tail, count);
1159 ring->tail = 0;
1160 port->icount.rx += count;
1161 }
1162
1163 /* Finally we read data from tail to head */
1164 if (ring->tail < ring->head) {
1165 count = ring->head - ring->tail;
1166
1167 tty_insert_flip_string(tport, ring->buf + ring->tail, count);
1168 /* Wrap ring->head if needed */
1169 if (ring->head >= sg_dma_len(&atmel_port->sg_rx))
1170 ring->head = 0;
1171 ring->tail = ring->head;
1172 port->icount.rx += count;
1173 }
1174
1175 /* USART retreives ownership of RX DMA buffer */
1176 dma_sync_sg_for_device(port->dev,
1177 &atmel_port->sg_rx,
1178 1,
1179 DMA_FROM_DEVICE);
1180
1181 /*
1182 * Drop the lock here since it might end up calling
1183 * uart_start(), which takes the lock.
1184 */
1185 spin_unlock(&port->lock);
1186 tty_flip_buffer_push(tport);
1187 spin_lock(&port->lock);
1188
1189 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT);
1190}
1191
1192static int atmel_prepare_rx_dma(struct uart_port *port)
1193{
1194 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1195 struct device *mfd_dev = port->dev->parent;
1196 struct dma_async_tx_descriptor *desc;
1197 dma_cap_mask_t mask;
1198 struct dma_slave_config config;
1199 struct circ_buf *ring;
1200 int ret, nent;
1201
1202 ring = &atmel_port->rx_ring;
1203
1204 dma_cap_zero(mask);
1205 dma_cap_set(DMA_CYCLIC, mask);
1206
1207 atmel_port->chan_rx = dma_request_slave_channel(mfd_dev, "rx");
1208 if (atmel_port->chan_rx == NULL)
1209 goto chan_err;
1210 dev_info(port->dev, "using %s for rx DMA transfers\n",
1211 dma_chan_name(atmel_port->chan_rx));
1212
1213 spin_lock_init(&atmel_port->lock_rx);
1214 sg_init_table(&atmel_port->sg_rx, 1);
1215 /* UART circular rx buffer is an aligned page. */
1216 BUG_ON(!PAGE_ALIGNED(ring->buf));
1217 sg_set_page(&atmel_port->sg_rx,
1218 virt_to_page(ring->buf),
1219 sizeof(struct atmel_uart_char) * ATMEL_SERIAL_RINGSIZE,
1220 offset_in_page(ring->buf));
1221 nent = dma_map_sg(port->dev,
1222 &atmel_port->sg_rx,
1223 1,
1224 DMA_FROM_DEVICE);
1225
1226 if (!nent) {
1227 dev_dbg(port->dev, "need to release resource of dma\n");
1228 goto chan_err;
1229 } else {
1230 dev_dbg(port->dev, "%s: mapped %d@%p to %pad\n", __func__,
1231 sg_dma_len(&atmel_port->sg_rx),
1232 ring->buf,
1233 &sg_dma_address(&atmel_port->sg_rx));
1234 }
1235
1236 /* Configure the slave DMA */
1237 memset(&config, 0, sizeof(config));
1238 config.direction = DMA_DEV_TO_MEM;
1239 config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
1240 config.src_addr = port->mapbase + ATMEL_US_RHR;
1241 config.src_maxburst = 1;
1242
1243 ret = dmaengine_slave_config(atmel_port->chan_rx,
1244 &config);
1245 if (ret) {
1246 dev_err(port->dev, "DMA rx slave configuration failed\n");
1247 goto chan_err;
1248 }
1249 /*
1250 * Prepare a cyclic dma transfer, assign 2 descriptors,
1251 * each one is half ring buffer size
1252 */
1253 desc = dmaengine_prep_dma_cyclic(atmel_port->chan_rx,
1254 sg_dma_address(&atmel_port->sg_rx),
1255 sg_dma_len(&atmel_port->sg_rx),
1256 sg_dma_len(&atmel_port->sg_rx)/2,
1257 DMA_DEV_TO_MEM,
1258 DMA_PREP_INTERRUPT);
1259 if (!desc) {
1260 dev_err(port->dev, "Preparing DMA cyclic failed\n");
1261 goto chan_err;
1262 }
1263 desc->callback = atmel_complete_rx_dma;
1264 desc->callback_param = port;
1265 atmel_port->desc_rx = desc;
1266 atmel_port->cookie_rx = dmaengine_submit(desc);
1267
1268 return 0;
1269
1270chan_err:
1271 dev_err(port->dev, "RX channel not available, switch to pio\n");
1272 atmel_port->use_dma_rx = false;
1273 if (atmel_port->chan_rx)
1274 atmel_release_rx_dma(port);
1275 return -EINVAL;
1276}
1277
1278static void atmel_uart_timer_callback(struct timer_list *t)
1279{
1280 struct atmel_uart_port *atmel_port = from_timer(atmel_port, t,
1281 uart_timer);
1282 struct uart_port *port = &atmel_port->uart;
1283
1284 if (!atomic_read(&atmel_port->tasklet_shutdown)) {
1285 tasklet_schedule(&atmel_port->tasklet_rx);
1286 mod_timer(&atmel_port->uart_timer,
1287 jiffies + uart_poll_timeout(port));
1288 }
1289}
1290
1291/*
1292 * receive interrupt handler.
1293 */
1294static void
1295atmel_handle_receive(struct uart_port *port, unsigned int pending)
1296{
1297 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1298
1299 if (atmel_use_pdc_rx(port)) {
1300 /*
1301 * PDC receive. Just schedule the tasklet and let it
1302 * figure out the details.
1303 *
1304 * TODO: We're not handling error flags correctly at
1305 * the moment.
1306 */
1307 if (pending & (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)) {
1308 atmel_uart_writel(port, ATMEL_US_IDR,
1309 (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT));
1310 atmel_tasklet_schedule(atmel_port,
1311 &atmel_port->tasklet_rx);
1312 }
1313
1314 if (pending & (ATMEL_US_RXBRK | ATMEL_US_OVRE |
1315 ATMEL_US_FRAME | ATMEL_US_PARE))
1316 atmel_pdc_rxerr(port, pending);
1317 }
1318
1319 if (atmel_use_dma_rx(port)) {
1320 if (pending & ATMEL_US_TIMEOUT) {
1321 atmel_uart_writel(port, ATMEL_US_IDR,
1322 ATMEL_US_TIMEOUT);
1323 atmel_tasklet_schedule(atmel_port,
1324 &atmel_port->tasklet_rx);
1325 }
1326 }
1327
1328 /* Interrupt receive */
1329 if (pending & ATMEL_US_RXRDY)
1330 atmel_rx_chars(port);
1331 else if (pending & ATMEL_US_RXBRK) {
1332 /*
1333 * End of break detected. If it came along with a
1334 * character, atmel_rx_chars will handle it.
1335 */
1336 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
1337 atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXBRK);
1338 atmel_port->break_active = 0;
1339 }
1340}
1341
1342/*
1343 * transmit interrupt handler. (Transmit is IRQF_NODELAY safe)
1344 */
1345static void
1346atmel_handle_transmit(struct uart_port *port, unsigned int pending)
1347{
1348 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1349
1350 if (pending & atmel_port->tx_done_mask) {
1351 atmel_uart_writel(port, ATMEL_US_IDR,
1352 atmel_port->tx_done_mask);
1353
1354 /* Start RX if flag was set and FIFO is empty */
1355 if (atmel_port->hd_start_rx) {
1356 if (!(atmel_uart_readl(port, ATMEL_US_CSR)
1357 & ATMEL_US_TXEMPTY))
1358 dev_warn(port->dev, "Should start RX, but TX fifo is not empty\n");
1359
1360 atmel_port->hd_start_rx = false;
1361 atmel_start_rx(port);
1362 }
1363
1364 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
1365 }
1366}
1367
1368/*
1369 * status flags interrupt handler.
1370 */
1371static void
1372atmel_handle_status(struct uart_port *port, unsigned int pending,
1373 unsigned int status)
1374{
1375 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1376 unsigned int status_change;
1377
1378 if (pending & (ATMEL_US_RIIC | ATMEL_US_DSRIC | ATMEL_US_DCDIC
1379 | ATMEL_US_CTSIC)) {
1380 status_change = status ^ atmel_port->irq_status_prev;
1381 atmel_port->irq_status_prev = status;
1382
1383 if (status_change & (ATMEL_US_RI | ATMEL_US_DSR
1384 | ATMEL_US_DCD | ATMEL_US_CTS)) {
1385 /* TODO: All reads to CSR will clear these interrupts! */
1386 if (status_change & ATMEL_US_RI)
1387 port->icount.rng++;
1388 if (status_change & ATMEL_US_DSR)
1389 port->icount.dsr++;
1390 if (status_change & ATMEL_US_DCD)
1391 uart_handle_dcd_change(port, !(status & ATMEL_US_DCD));
1392 if (status_change & ATMEL_US_CTS)
1393 uart_handle_cts_change(port, !(status & ATMEL_US_CTS));
1394
1395 wake_up_interruptible(&port->state->port.delta_msr_wait);
1396 }
1397 }
1398
1399 if (pending & (ATMEL_US_NACK | ATMEL_US_ITERATION))
1400 dev_dbg(port->dev, "ISO7816 ERROR (0x%08x)\n", pending);
1401}
1402
1403/*
1404 * Interrupt handler
1405 */
1406static irqreturn_t atmel_interrupt(int irq, void *dev_id)
1407{
1408 struct uart_port *port = dev_id;
1409 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1410 unsigned int status, pending, mask, pass_counter = 0;
1411
1412 spin_lock(&atmel_port->lock_suspended);
1413
1414 do {
1415 status = atmel_uart_readl(port, ATMEL_US_CSR);
1416 mask = atmel_uart_readl(port, ATMEL_US_IMR);
1417 pending = status & mask;
1418 if (!pending)
1419 break;
1420
1421 if (atmel_port->suspended) {
1422 atmel_port->pending |= pending;
1423 atmel_port->pending_status = status;
1424 atmel_uart_writel(port, ATMEL_US_IDR, mask);
1425 pm_system_wakeup();
1426 break;
1427 }
1428
1429 atmel_handle_receive(port, pending);
1430 atmel_handle_status(port, pending, status);
1431 atmel_handle_transmit(port, pending);
1432 } while (pass_counter++ < ATMEL_ISR_PASS_LIMIT);
1433
1434 spin_unlock(&atmel_port->lock_suspended);
1435
1436 return pass_counter ? IRQ_HANDLED : IRQ_NONE;
1437}
1438
1439static void atmel_release_tx_pdc(struct uart_port *port)
1440{
1441 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1442 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1443
1444 dma_unmap_single(port->dev,
1445 pdc->dma_addr,
1446 pdc->dma_size,
1447 DMA_TO_DEVICE);
1448}
1449
1450/*
1451 * Called from tasklet with ENDTX and TXBUFE interrupts disabled.
1452 */
1453static void atmel_tx_pdc(struct uart_port *port)
1454{
1455 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1456 struct circ_buf *xmit = &port->state->xmit;
1457 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1458 int count;
1459
1460 /* nothing left to transmit? */
1461 if (atmel_uart_readl(port, ATMEL_PDC_TCR))
1462 return;
1463
1464 xmit->tail += pdc->ofs;
1465 xmit->tail &= UART_XMIT_SIZE - 1;
1466
1467 port->icount.tx += pdc->ofs;
1468 pdc->ofs = 0;
1469
1470 /* more to transmit - setup next transfer */
1471
1472 /* disable PDC transmit */
1473 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
1474
1475 if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) {
1476 dma_sync_single_for_device(port->dev,
1477 pdc->dma_addr,
1478 pdc->dma_size,
1479 DMA_TO_DEVICE);
1480
1481 count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
1482 pdc->ofs = count;
1483
1484 atmel_uart_writel(port, ATMEL_PDC_TPR,
1485 pdc->dma_addr + xmit->tail);
1486 atmel_uart_writel(port, ATMEL_PDC_TCR, count);
1487 /* re-enable PDC transmit */
1488 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
1489 /* Enable interrupts */
1490 atmel_uart_writel(port, ATMEL_US_IER,
1491 atmel_port->tx_done_mask);
1492 } else {
1493 if (atmel_uart_is_half_duplex(port)) {
1494 /* DMA done, stop TX, start RX for RS485 */
1495 atmel_start_rx(port);
1496 }
1497 }
1498
1499 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
1500 uart_write_wakeup(port);
1501}
1502
1503static int atmel_prepare_tx_pdc(struct uart_port *port)
1504{
1505 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1506 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1507 struct circ_buf *xmit = &port->state->xmit;
1508
1509 pdc->buf = xmit->buf;
1510 pdc->dma_addr = dma_map_single(port->dev,
1511 pdc->buf,
1512 UART_XMIT_SIZE,
1513 DMA_TO_DEVICE);
1514 pdc->dma_size = UART_XMIT_SIZE;
1515 pdc->ofs = 0;
1516
1517 return 0;
1518}
1519
1520static void atmel_rx_from_ring(struct uart_port *port)
1521{
1522 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1523 struct circ_buf *ring = &atmel_port->rx_ring;
1524 unsigned int flg;
1525 unsigned int status;
1526
1527 while (ring->head != ring->tail) {
1528 struct atmel_uart_char c;
1529
1530 /* Make sure c is loaded after head. */
1531 smp_rmb();
1532
1533 c = ((struct atmel_uart_char *)ring->buf)[ring->tail];
1534
1535 ring->tail = (ring->tail + 1) & (ATMEL_SERIAL_RINGSIZE - 1);
1536
1537 port->icount.rx++;
1538 status = c.status;
1539 flg = TTY_NORMAL;
1540
1541 /*
1542 * note that the error handling code is
1543 * out of the main execution path
1544 */
1545 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME
1546 | ATMEL_US_OVRE | ATMEL_US_RXBRK))) {
1547 if (status & ATMEL_US_RXBRK) {
1548 /* ignore side-effect */
1549 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);
1550
1551 port->icount.brk++;
1552 if (uart_handle_break(port))
1553 continue;
1554 }
1555 if (status & ATMEL_US_PARE)
1556 port->icount.parity++;
1557 if (status & ATMEL_US_FRAME)
1558 port->icount.frame++;
1559 if (status & ATMEL_US_OVRE)
1560 port->icount.overrun++;
1561
1562 status &= port->read_status_mask;
1563
1564 if (status & ATMEL_US_RXBRK)
1565 flg = TTY_BREAK;
1566 else if (status & ATMEL_US_PARE)
1567 flg = TTY_PARITY;
1568 else if (status & ATMEL_US_FRAME)
1569 flg = TTY_FRAME;
1570 }
1571
1572
1573 if (uart_handle_sysrq_char(port, c.ch))
1574 continue;
1575
1576 uart_insert_char(port, status, ATMEL_US_OVRE, c.ch, flg);
1577 }
1578
1579 /*
1580 * Drop the lock here since it might end up calling
1581 * uart_start(), which takes the lock.
1582 */
1583 spin_unlock(&port->lock);
1584 tty_flip_buffer_push(&port->state->port);
1585 spin_lock(&port->lock);
1586}
1587
1588static void atmel_release_rx_pdc(struct uart_port *port)
1589{
1590 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1591 int i;
1592
1593 for (i = 0; i < 2; i++) {
1594 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
1595
1596 dma_unmap_single(port->dev,
1597 pdc->dma_addr,
1598 pdc->dma_size,
1599 DMA_FROM_DEVICE);
1600 kfree(pdc->buf);
1601 }
1602}
1603
1604static void atmel_rx_from_pdc(struct uart_port *port)
1605{
1606 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1607 struct tty_port *tport = &port->state->port;
1608 struct atmel_dma_buffer *pdc;
1609 int rx_idx = atmel_port->pdc_rx_idx;
1610 unsigned int head;
1611 unsigned int tail;
1612 unsigned int count;
1613
1614 do {
1615 /* Reset the UART timeout early so that we don't miss one */
1616 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1617
1618 pdc = &atmel_port->pdc_rx[rx_idx];
1619 head = atmel_uart_readl(port, ATMEL_PDC_RPR) - pdc->dma_addr;
1620 tail = pdc->ofs;
1621
1622 /* If the PDC has switched buffers, RPR won't contain
1623 * any address within the current buffer. Since head
1624 * is unsigned, we just need a one-way comparison to
1625 * find out.
1626 *
1627 * In this case, we just need to consume the entire
1628 * buffer and resubmit it for DMA. This will clear the
1629 * ENDRX bit as well, so that we can safely re-enable
1630 * all interrupts below.
1631 */
1632 head = min(head, pdc->dma_size);
1633
1634 if (likely(head != tail)) {
1635 dma_sync_single_for_cpu(port->dev, pdc->dma_addr,
1636 pdc->dma_size, DMA_FROM_DEVICE);
1637
1638 /*
1639 * head will only wrap around when we recycle
1640 * the DMA buffer, and when that happens, we
1641 * explicitly set tail to 0. So head will
1642 * always be greater than tail.
1643 */
1644 count = head - tail;
1645
1646 tty_insert_flip_string(tport, pdc->buf + pdc->ofs,
1647 count);
1648
1649 dma_sync_single_for_device(port->dev, pdc->dma_addr,
1650 pdc->dma_size, DMA_FROM_DEVICE);
1651
1652 port->icount.rx += count;
1653 pdc->ofs = head;
1654 }
1655
1656 /*
1657 * If the current buffer is full, we need to check if
1658 * the next one contains any additional data.
1659 */
1660 if (head >= pdc->dma_size) {
1661 pdc->ofs = 0;
1662 atmel_uart_writel(port, ATMEL_PDC_RNPR, pdc->dma_addr);
1663 atmel_uart_writel(port, ATMEL_PDC_RNCR, pdc->dma_size);
1664
1665 rx_idx = !rx_idx;
1666 atmel_port->pdc_rx_idx = rx_idx;
1667 }
1668 } while (head >= pdc->dma_size);
1669
1670 /*
1671 * Drop the lock here since it might end up calling
1672 * uart_start(), which takes the lock.
1673 */
1674 spin_unlock(&port->lock);
1675 tty_flip_buffer_push(tport);
1676 spin_lock(&port->lock);
1677
1678 atmel_uart_writel(port, ATMEL_US_IER,
1679 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
1680}
1681
1682static int atmel_prepare_rx_pdc(struct uart_port *port)
1683{
1684 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1685 int i;
1686
1687 for (i = 0; i < 2; i++) {
1688 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
1689
1690 pdc->buf = kmalloc(PDC_BUFFER_SIZE, GFP_KERNEL);
1691 if (pdc->buf == NULL) {
1692 if (i != 0) {
1693 dma_unmap_single(port->dev,
1694 atmel_port->pdc_rx[0].dma_addr,
1695 PDC_BUFFER_SIZE,
1696 DMA_FROM_DEVICE);
1697 kfree(atmel_port->pdc_rx[0].buf);
1698 }
1699 atmel_port->use_pdc_rx = false;
1700 return -ENOMEM;
1701 }
1702 pdc->dma_addr = dma_map_single(port->dev,
1703 pdc->buf,
1704 PDC_BUFFER_SIZE,
1705 DMA_FROM_DEVICE);
1706 pdc->dma_size = PDC_BUFFER_SIZE;
1707 pdc->ofs = 0;
1708 }
1709
1710 atmel_port->pdc_rx_idx = 0;
1711
1712 atmel_uart_writel(port, ATMEL_PDC_RPR, atmel_port->pdc_rx[0].dma_addr);
1713 atmel_uart_writel(port, ATMEL_PDC_RCR, PDC_BUFFER_SIZE);
1714
1715 atmel_uart_writel(port, ATMEL_PDC_RNPR,
1716 atmel_port->pdc_rx[1].dma_addr);
1717 atmel_uart_writel(port, ATMEL_PDC_RNCR, PDC_BUFFER_SIZE);
1718
1719 return 0;
1720}
1721
1722/*
1723 * tasklet handling tty stuff outside the interrupt handler.
1724 */
1725static void atmel_tasklet_rx_func(unsigned long data)
1726{
1727 struct uart_port *port = (struct uart_port *)data;
1728 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1729
1730 /* The interrupt handler does not take the lock */
1731 spin_lock(&port->lock);
1732 atmel_port->schedule_rx(port);
1733 spin_unlock(&port->lock);
1734}
1735
1736static void atmel_tasklet_tx_func(unsigned long data)
1737{
1738 struct uart_port *port = (struct uart_port *)data;
1739 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1740
1741 /* The interrupt handler does not take the lock */
1742 spin_lock(&port->lock);
1743 atmel_port->schedule_tx(port);
1744 spin_unlock(&port->lock);
1745}
1746
1747static void atmel_init_property(struct atmel_uart_port *atmel_port,
1748 struct platform_device *pdev)
1749{
1750 struct device_node *np = pdev->dev.of_node;
1751
1752 /* DMA/PDC usage specification */
1753 if (of_property_read_bool(np, "atmel,use-dma-rx")) {
1754 if (of_property_read_bool(np, "dmas")) {
1755 atmel_port->use_dma_rx = true;
1756 atmel_port->use_pdc_rx = false;
1757 } else {
1758 atmel_port->use_dma_rx = false;
1759 atmel_port->use_pdc_rx = true;
1760 }
1761 } else {
1762 atmel_port->use_dma_rx = false;
1763 atmel_port->use_pdc_rx = false;
1764 }
1765
1766 if (of_property_read_bool(np, "atmel,use-dma-tx")) {
1767 if (of_property_read_bool(np, "dmas")) {
1768 atmel_port->use_dma_tx = true;
1769 atmel_port->use_pdc_tx = false;
1770 } else {
1771 atmel_port->use_dma_tx = false;
1772 atmel_port->use_pdc_tx = true;
1773 }
1774 } else {
1775 atmel_port->use_dma_tx = false;
1776 atmel_port->use_pdc_tx = false;
1777 }
1778}
1779
1780static void atmel_set_ops(struct uart_port *port)
1781{
1782 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1783
1784 if (atmel_use_dma_rx(port)) {
1785 atmel_port->prepare_rx = &atmel_prepare_rx_dma;
1786 atmel_port->schedule_rx = &atmel_rx_from_dma;
1787 atmel_port->release_rx = &atmel_release_rx_dma;
1788 } else if (atmel_use_pdc_rx(port)) {
1789 atmel_port->prepare_rx = &atmel_prepare_rx_pdc;
1790 atmel_port->schedule_rx = &atmel_rx_from_pdc;
1791 atmel_port->release_rx = &atmel_release_rx_pdc;
1792 } else {
1793 atmel_port->prepare_rx = NULL;
1794 atmel_port->schedule_rx = &atmel_rx_from_ring;
1795 atmel_port->release_rx = NULL;
1796 }
1797
1798 if (atmel_use_dma_tx(port)) {
1799 atmel_port->prepare_tx = &atmel_prepare_tx_dma;
1800 atmel_port->schedule_tx = &atmel_tx_dma;
1801 atmel_port->release_tx = &atmel_release_tx_dma;
1802 } else if (atmel_use_pdc_tx(port)) {
1803 atmel_port->prepare_tx = &atmel_prepare_tx_pdc;
1804 atmel_port->schedule_tx = &atmel_tx_pdc;
1805 atmel_port->release_tx = &atmel_release_tx_pdc;
1806 } else {
1807 atmel_port->prepare_tx = NULL;
1808 atmel_port->schedule_tx = &atmel_tx_chars;
1809 atmel_port->release_tx = NULL;
1810 }
1811}
1812
1813/*
1814 * Get ip name usart or uart
1815 */
1816static void atmel_get_ip_name(struct uart_port *port)
1817{
1818 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1819 int name = atmel_uart_readl(port, ATMEL_US_NAME);
1820 u32 version;
1821 u32 usart, dbgu_uart, new_uart;
1822 /* ASCII decoding for IP version */
1823 usart = 0x55534152; /* USAR(T) */
1824 dbgu_uart = 0x44424755; /* DBGU */
1825 new_uart = 0x55415254; /* UART */
1826
1827 /*
1828 * Only USART devices from at91sam9260 SOC implement fractional
1829 * baudrate. It is available for all asynchronous modes, with the
1830 * following restriction: the sampling clock's duty cycle is not
1831 * constant.
1832 */
1833 atmel_port->has_frac_baudrate = false;
1834 atmel_port->has_hw_timer = false;
1835
1836 if (name == new_uart) {
1837 dev_dbg(port->dev, "Uart with hw timer");
1838 atmel_port->has_hw_timer = true;
1839 atmel_port->rtor = ATMEL_UA_RTOR;
1840 } else if (name == usart) {
1841 dev_dbg(port->dev, "Usart\n");
1842 atmel_port->has_frac_baudrate = true;
1843 atmel_port->has_hw_timer = true;
1844 atmel_port->rtor = ATMEL_US_RTOR;
1845 version = atmel_uart_readl(port, ATMEL_US_VERSION);
1846 switch (version) {
1847 case 0x814: /* sama5d2 */
1848 fallthrough;
1849 case 0x701: /* sama5d4 */
1850 atmel_port->fidi_min = 3;
1851 atmel_port->fidi_max = 65535;
1852 break;
1853 case 0x502: /* sam9x5, sama5d3 */
1854 atmel_port->fidi_min = 3;
1855 atmel_port->fidi_max = 2047;
1856 break;
1857 default:
1858 atmel_port->fidi_min = 1;
1859 atmel_port->fidi_max = 2047;
1860 }
1861 } else if (name == dbgu_uart) {
1862 dev_dbg(port->dev, "Dbgu or uart without hw timer\n");
1863 } else {
1864 /* fallback for older SoCs: use version field */
1865 version = atmel_uart_readl(port, ATMEL_US_VERSION);
1866 switch (version) {
1867 case 0x302:
1868 case 0x10213:
1869 case 0x10302:
1870 dev_dbg(port->dev, "This version is usart\n");
1871 atmel_port->has_frac_baudrate = true;
1872 atmel_port->has_hw_timer = true;
1873 atmel_port->rtor = ATMEL_US_RTOR;
1874 break;
1875 case 0x203:
1876 case 0x10202:
1877 dev_dbg(port->dev, "This version is uart\n");
1878 break;
1879 default:
1880 dev_err(port->dev, "Not supported ip name nor version, set to uart\n");
1881 }
1882 }
1883}
1884
1885/*
1886 * Perform initialization and enable port for reception
1887 */
1888static int atmel_startup(struct uart_port *port)
1889{
1890 struct platform_device *pdev = to_platform_device(port->dev);
1891 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1892 int retval;
1893
1894 /*
1895 * Ensure that no interrupts are enabled otherwise when
1896 * request_irq() is called we could get stuck trying to
1897 * handle an unexpected interrupt
1898 */
1899 atmel_uart_writel(port, ATMEL_US_IDR, -1);
1900 atmel_port->ms_irq_enabled = false;
1901
1902 /*
1903 * Allocate the IRQ
1904 */
1905 retval = request_irq(port->irq, atmel_interrupt,
1906 IRQF_SHARED | IRQF_COND_SUSPEND,
1907 dev_name(&pdev->dev), port);
1908 if (retval) {
1909 dev_err(port->dev, "atmel_startup - Can't get irq\n");
1910 return retval;
1911 }
1912
1913 atomic_set(&atmel_port->tasklet_shutdown, 0);
1914 tasklet_init(&atmel_port->tasklet_rx, atmel_tasklet_rx_func,
1915 (unsigned long)port);
1916 tasklet_init(&atmel_port->tasklet_tx, atmel_tasklet_tx_func,
1917 (unsigned long)port);
1918
1919 /*
1920 * Initialize DMA (if necessary)
1921 */
1922 atmel_init_property(atmel_port, pdev);
1923 atmel_set_ops(port);
1924
1925 if (atmel_port->prepare_rx) {
1926 retval = atmel_port->prepare_rx(port);
1927 if (retval < 0)
1928 atmel_set_ops(port);
1929 }
1930
1931 if (atmel_port->prepare_tx) {
1932 retval = atmel_port->prepare_tx(port);
1933 if (retval < 0)
1934 atmel_set_ops(port);
1935 }
1936
1937 /*
1938 * Enable FIFO when available
1939 */
1940 if (atmel_port->fifo_size) {
1941 unsigned int txrdym = ATMEL_US_ONE_DATA;
1942 unsigned int rxrdym = ATMEL_US_ONE_DATA;
1943 unsigned int fmr;
1944
1945 atmel_uart_writel(port, ATMEL_US_CR,
1946 ATMEL_US_FIFOEN |
1947 ATMEL_US_RXFCLR |
1948 ATMEL_US_TXFLCLR);
1949
1950 if (atmel_use_dma_tx(port))
1951 txrdym = ATMEL_US_FOUR_DATA;
1952
1953 fmr = ATMEL_US_TXRDYM(txrdym) | ATMEL_US_RXRDYM(rxrdym);
1954 if (atmel_port->rts_high &&
1955 atmel_port->rts_low)
1956 fmr |= ATMEL_US_FRTSC |
1957 ATMEL_US_RXFTHRES(atmel_port->rts_high) |
1958 ATMEL_US_RXFTHRES2(atmel_port->rts_low);
1959
1960 atmel_uart_writel(port, ATMEL_US_FMR, fmr);
1961 }
1962
1963 /* Save current CSR for comparison in atmel_tasklet_func() */
1964 atmel_port->irq_status_prev = atmel_uart_readl(port, ATMEL_US_CSR);
1965
1966 /*
1967 * Finally, enable the serial port
1968 */
1969 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
1970 /* enable xmit & rcvr */
1971 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
1972 atmel_port->tx_stopped = false;
1973
1974 timer_setup(&atmel_port->uart_timer, atmel_uart_timer_callback, 0);
1975
1976 if (atmel_use_pdc_rx(port)) {
1977 /* set UART timeout */
1978 if (!atmel_port->has_hw_timer) {
1979 mod_timer(&atmel_port->uart_timer,
1980 jiffies + uart_poll_timeout(port));
1981 /* set USART timeout */
1982 } else {
1983 atmel_uart_writel(port, atmel_port->rtor,
1984 PDC_RX_TIMEOUT);
1985 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1986
1987 atmel_uart_writel(port, ATMEL_US_IER,
1988 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
1989 }
1990 /* enable PDC controller */
1991 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
1992 } else if (atmel_use_dma_rx(port)) {
1993 /* set UART timeout */
1994 if (!atmel_port->has_hw_timer) {
1995 mod_timer(&atmel_port->uart_timer,
1996 jiffies + uart_poll_timeout(port));
1997 /* set USART timeout */
1998 } else {
1999 atmel_uart_writel(port, atmel_port->rtor,
2000 PDC_RX_TIMEOUT);
2001 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
2002
2003 atmel_uart_writel(port, ATMEL_US_IER,
2004 ATMEL_US_TIMEOUT);
2005 }
2006 } else {
2007 /* enable receive only */
2008 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY);
2009 }
2010
2011 return 0;
2012}
2013
2014/*
2015 * Flush any TX data submitted for DMA. Called when the TX circular
2016 * buffer is reset.
2017 */
2018static void atmel_flush_buffer(struct uart_port *port)
2019{
2020 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2021
2022 if (atmel_use_pdc_tx(port)) {
2023 atmel_uart_writel(port, ATMEL_PDC_TCR, 0);
2024 atmel_port->pdc_tx.ofs = 0;
2025 }
2026 /*
2027 * in uart_flush_buffer(), the xmit circular buffer has just
2028 * been cleared, so we have to reset tx_len accordingly.
2029 */
2030 atmel_port->tx_len = 0;
2031}
2032
2033/*
2034 * Disable the port
2035 */
2036static void atmel_shutdown(struct uart_port *port)
2037{
2038 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2039
2040 /* Disable modem control lines interrupts */
2041 atmel_disable_ms(port);
2042
2043 /* Disable interrupts at device level */
2044 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2045
2046 /* Prevent spurious interrupts from scheduling the tasklet */
2047 atomic_inc(&atmel_port->tasklet_shutdown);
2048
2049 /*
2050 * Prevent any tasklets being scheduled during
2051 * cleanup
2052 */
2053 del_timer_sync(&atmel_port->uart_timer);
2054
2055 /* Make sure that no interrupt is on the fly */
2056 synchronize_irq(port->irq);
2057
2058 /*
2059 * Clear out any scheduled tasklets before
2060 * we destroy the buffers
2061 */
2062 tasklet_kill(&atmel_port->tasklet_rx);
2063 tasklet_kill(&atmel_port->tasklet_tx);
2064
2065 /*
2066 * Ensure everything is stopped and
2067 * disable port and break condition.
2068 */
2069 atmel_stop_rx(port);
2070 atmel_stop_tx(port);
2071
2072 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
2073
2074 /*
2075 * Shut-down the DMA.
2076 */
2077 if (atmel_port->release_rx)
2078 atmel_port->release_rx(port);
2079 if (atmel_port->release_tx)
2080 atmel_port->release_tx(port);
2081
2082 /*
2083 * Reset ring buffer pointers
2084 */
2085 atmel_port->rx_ring.head = 0;
2086 atmel_port->rx_ring.tail = 0;
2087
2088 /*
2089 * Free the interrupts
2090 */
2091 free_irq(port->irq, port);
2092
2093 atmel_flush_buffer(port);
2094}
2095
2096/*
2097 * Power / Clock management.
2098 */
2099static void atmel_serial_pm(struct uart_port *port, unsigned int state,
2100 unsigned int oldstate)
2101{
2102 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2103
2104 switch (state) {
2105 case 0:
2106 /*
2107 * Enable the peripheral clock for this serial port.
2108 * This is called on uart_open() or a resume event.
2109 */
2110 clk_prepare_enable(atmel_port->clk);
2111
2112 /* re-enable interrupts if we disabled some on suspend */
2113 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->backup_imr);
2114 break;
2115 case 3:
2116 /* Back up the interrupt mask and disable all interrupts */
2117 atmel_port->backup_imr = atmel_uart_readl(port, ATMEL_US_IMR);
2118 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2119
2120 /*
2121 * Disable the peripheral clock for this serial port.
2122 * This is called on uart_close() or a suspend event.
2123 */
2124 clk_disable_unprepare(atmel_port->clk);
2125 break;
2126 default:
2127 dev_err(port->dev, "atmel_serial: unknown pm %d\n", state);
2128 }
2129}
2130
2131/*
2132 * Change the port parameters
2133 */
2134static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
2135 struct ktermios *old)
2136{
2137 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2138 unsigned long flags;
2139 unsigned int old_mode, mode, imr, quot, baud, div, cd, fp = 0;
2140
2141 /* save the current mode register */
2142 mode = old_mode = atmel_uart_readl(port, ATMEL_US_MR);
2143
2144 /* reset the mode, clock divisor, parity, stop bits and data size */
2145 mode &= ~(ATMEL_US_USCLKS | ATMEL_US_CHRL | ATMEL_US_NBSTOP |
2146 ATMEL_US_PAR | ATMEL_US_USMODE);
2147
2148 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
2149
2150 /* byte size */
2151 switch (termios->c_cflag & CSIZE) {
2152 case CS5:
2153 mode |= ATMEL_US_CHRL_5;
2154 break;
2155 case CS6:
2156 mode |= ATMEL_US_CHRL_6;
2157 break;
2158 case CS7:
2159 mode |= ATMEL_US_CHRL_7;
2160 break;
2161 default:
2162 mode |= ATMEL_US_CHRL_8;
2163 break;
2164 }
2165
2166 /* stop bits */
2167 if (termios->c_cflag & CSTOPB)
2168 mode |= ATMEL_US_NBSTOP_2;
2169
2170 /* parity */
2171 if (termios->c_cflag & PARENB) {
2172 /* Mark or Space parity */
2173 if (termios->c_cflag & CMSPAR) {
2174 if (termios->c_cflag & PARODD)
2175 mode |= ATMEL_US_PAR_MARK;
2176 else
2177 mode |= ATMEL_US_PAR_SPACE;
2178 } else if (termios->c_cflag & PARODD)
2179 mode |= ATMEL_US_PAR_ODD;
2180 else
2181 mode |= ATMEL_US_PAR_EVEN;
2182 } else
2183 mode |= ATMEL_US_PAR_NONE;
2184
2185 spin_lock_irqsave(&port->lock, flags);
2186
2187 port->read_status_mask = ATMEL_US_OVRE;
2188 if (termios->c_iflag & INPCK)
2189 port->read_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE);
2190 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
2191 port->read_status_mask |= ATMEL_US_RXBRK;
2192
2193 if (atmel_use_pdc_rx(port))
2194 /* need to enable error interrupts */
2195 atmel_uart_writel(port, ATMEL_US_IER, port->read_status_mask);
2196
2197 /*
2198 * Characters to ignore
2199 */
2200 port->ignore_status_mask = 0;
2201 if (termios->c_iflag & IGNPAR)
2202 port->ignore_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE);
2203 if (termios->c_iflag & IGNBRK) {
2204 port->ignore_status_mask |= ATMEL_US_RXBRK;
2205 /*
2206 * If we're ignoring parity and break indicators,
2207 * ignore overruns too (for real raw support).
2208 */
2209 if (termios->c_iflag & IGNPAR)
2210 port->ignore_status_mask |= ATMEL_US_OVRE;
2211 }
2212 /* TODO: Ignore all characters if CREAD is set.*/
2213
2214 /* update the per-port timeout */
2215 uart_update_timeout(port, termios->c_cflag, baud);
2216
2217 /*
2218 * save/disable interrupts. The tty layer will ensure that the
2219 * transmitter is empty if requested by the caller, so there's
2220 * no need to wait for it here.
2221 */
2222 imr = atmel_uart_readl(port, ATMEL_US_IMR);
2223 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2224
2225 /* disable receiver and transmitter */
2226 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXDIS);
2227 atmel_port->tx_stopped = true;
2228
2229 /* mode */
2230 if (port->rs485.flags & SER_RS485_ENABLED) {
2231 atmel_uart_writel(port, ATMEL_US_TTGR,
2232 port->rs485.delay_rts_after_send);
2233 mode |= ATMEL_US_USMODE_RS485;
2234 } else if (port->iso7816.flags & SER_ISO7816_ENABLED) {
2235 atmel_uart_writel(port, ATMEL_US_TTGR, port->iso7816.tg);
2236 /* select mck clock, and output */
2237 mode |= ATMEL_US_USCLKS_MCK | ATMEL_US_CLKO;
2238 /* set max iterations */
2239 mode |= ATMEL_US_MAX_ITER(3);
2240 if ((port->iso7816.flags & SER_ISO7816_T_PARAM)
2241 == SER_ISO7816_T(0))
2242 mode |= ATMEL_US_USMODE_ISO7816_T0;
2243 else
2244 mode |= ATMEL_US_USMODE_ISO7816_T1;
2245 } else if (termios->c_cflag & CRTSCTS) {
2246 /* RS232 with hardware handshake (RTS/CTS) */
2247 if (atmel_use_fifo(port) &&
2248 !mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS)) {
2249 /*
2250 * with ATMEL_US_USMODE_HWHS set, the controller will
2251 * be able to drive the RTS pin high/low when the RX
2252 * FIFO is above RXFTHRES/below RXFTHRES2.
2253 * It will also disable the transmitter when the CTS
2254 * pin is high.
2255 * This mode is not activated if CTS pin is a GPIO
2256 * because in this case, the transmitter is always
2257 * disabled (there must be an internal pull-up
2258 * responsible for this behaviour).
2259 * If the RTS pin is a GPIO, the controller won't be
2260 * able to drive it according to the FIFO thresholds,
2261 * but it will be handled by the driver.
2262 */
2263 mode |= ATMEL_US_USMODE_HWHS;
2264 } else {
2265 /*
2266 * For platforms without FIFO, the flow control is
2267 * handled by the driver.
2268 */
2269 mode |= ATMEL_US_USMODE_NORMAL;
2270 }
2271 } else {
2272 /* RS232 without hadware handshake */
2273 mode |= ATMEL_US_USMODE_NORMAL;
2274 }
2275
2276 /*
2277 * Set the baud rate:
2278 * Fractional baudrate allows to setup output frequency more
2279 * accurately. This feature is enabled only when using normal mode.
2280 * baudrate = selected clock / (8 * (2 - OVER) * (CD + FP / 8))
2281 * Currently, OVER is always set to 0 so we get
2282 * baudrate = selected clock / (16 * (CD + FP / 8))
2283 * then
2284 * 8 CD + FP = selected clock / (2 * baudrate)
2285 */
2286 if (atmel_port->has_frac_baudrate) {
2287 div = DIV_ROUND_CLOSEST(port->uartclk, baud * 2);
2288 cd = div >> 3;
2289 fp = div & ATMEL_US_FP_MASK;
2290 } else {
2291 cd = uart_get_divisor(port, baud);
2292 }
2293
2294 if (cd > 65535) { /* BRGR is 16-bit, so switch to slower clock */
2295 cd /= 8;
2296 mode |= ATMEL_US_USCLKS_MCK_DIV8;
2297 }
2298 quot = cd | fp << ATMEL_US_FP_OFFSET;
2299
2300 if (!(port->iso7816.flags & SER_ISO7816_ENABLED))
2301 atmel_uart_writel(port, ATMEL_US_BRGR, quot);
2302
2303 /* set the mode, clock divisor, parity, stop bits and data size */
2304 atmel_uart_writel(port, ATMEL_US_MR, mode);
2305
2306 /*
2307 * when switching the mode, set the RTS line state according to the
2308 * new mode, otherwise keep the former state
2309 */
2310 if ((old_mode & ATMEL_US_USMODE) != (mode & ATMEL_US_USMODE)) {
2311 unsigned int rts_state;
2312
2313 if ((mode & ATMEL_US_USMODE) == ATMEL_US_USMODE_HWHS) {
2314 /* let the hardware control the RTS line */
2315 rts_state = ATMEL_US_RTSDIS;
2316 } else {
2317 /* force RTS line to low level */
2318 rts_state = ATMEL_US_RTSEN;
2319 }
2320
2321 atmel_uart_writel(port, ATMEL_US_CR, rts_state);
2322 }
2323
2324 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
2325 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
2326 atmel_port->tx_stopped = false;
2327
2328 /* restore interrupts */
2329 atmel_uart_writel(port, ATMEL_US_IER, imr);
2330
2331 /* CTS flow-control and modem-status interrupts */
2332 if (UART_ENABLE_MS(port, termios->c_cflag))
2333 atmel_enable_ms(port);
2334 else
2335 atmel_disable_ms(port);
2336
2337 spin_unlock_irqrestore(&port->lock, flags);
2338}
2339
2340static void atmel_set_ldisc(struct uart_port *port, struct ktermios *termios)
2341{
2342 if (termios->c_line == N_PPS) {
2343 port->flags |= UPF_HARDPPS_CD;
2344 spin_lock_irq(&port->lock);
2345 atmel_enable_ms(port);
2346 spin_unlock_irq(&port->lock);
2347 } else {
2348 port->flags &= ~UPF_HARDPPS_CD;
2349 if (!UART_ENABLE_MS(port, termios->c_cflag)) {
2350 spin_lock_irq(&port->lock);
2351 atmel_disable_ms(port);
2352 spin_unlock_irq(&port->lock);
2353 }
2354 }
2355}
2356
2357/*
2358 * Return string describing the specified port
2359 */
2360static const char *atmel_type(struct uart_port *port)
2361{
2362 return (port->type == PORT_ATMEL) ? "ATMEL_SERIAL" : NULL;
2363}
2364
2365/*
2366 * Release the memory region(s) being used by 'port'.
2367 */
2368static void atmel_release_port(struct uart_port *port)
2369{
2370 struct platform_device *mpdev = to_platform_device(port->dev->parent);
2371 int size = resource_size(mpdev->resource);
2372
2373 release_mem_region(port->mapbase, size);
2374
2375 if (port->flags & UPF_IOREMAP) {
2376 iounmap(port->membase);
2377 port->membase = NULL;
2378 }
2379}
2380
2381/*
2382 * Request the memory region(s) being used by 'port'.
2383 */
2384static int atmel_request_port(struct uart_port *port)
2385{
2386 struct platform_device *mpdev = to_platform_device(port->dev->parent);
2387 int size = resource_size(mpdev->resource);
2388
2389 if (!request_mem_region(port->mapbase, size, "atmel_serial"))
2390 return -EBUSY;
2391
2392 if (port->flags & UPF_IOREMAP) {
2393 port->membase = ioremap(port->mapbase, size);
2394 if (port->membase == NULL) {
2395 release_mem_region(port->mapbase, size);
2396 return -ENOMEM;
2397 }
2398 }
2399
2400 return 0;
2401}
2402
2403/*
2404 * Configure/autoconfigure the port.
2405 */
2406static void atmel_config_port(struct uart_port *port, int flags)
2407{
2408 if (flags & UART_CONFIG_TYPE) {
2409 port->type = PORT_ATMEL;
2410 atmel_request_port(port);
2411 }
2412}
2413
2414/*
2415 * Verify the new serial_struct (for TIOCSSERIAL).
2416 */
2417static int atmel_verify_port(struct uart_port *port, struct serial_struct *ser)
2418{
2419 int ret = 0;
2420 if (ser->type != PORT_UNKNOWN && ser->type != PORT_ATMEL)
2421 ret = -EINVAL;
2422 if (port->irq != ser->irq)
2423 ret = -EINVAL;
2424 if (ser->io_type != SERIAL_IO_MEM)
2425 ret = -EINVAL;
2426 if (port->uartclk / 16 != ser->baud_base)
2427 ret = -EINVAL;
2428 if (port->mapbase != (unsigned long)ser->iomem_base)
2429 ret = -EINVAL;
2430 if (port->iobase != ser->port)
2431 ret = -EINVAL;
2432 if (ser->hub6 != 0)
2433 ret = -EINVAL;
2434 return ret;
2435}
2436
2437#ifdef CONFIG_CONSOLE_POLL
2438static int atmel_poll_get_char(struct uart_port *port)
2439{
2440 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_RXRDY))
2441 cpu_relax();
2442
2443 return atmel_uart_read_char(port);
2444}
2445
2446static void atmel_poll_put_char(struct uart_port *port, unsigned char ch)
2447{
2448 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY))
2449 cpu_relax();
2450
2451 atmel_uart_write_char(port, ch);
2452}
2453#endif
2454
2455static const struct uart_ops atmel_pops = {
2456 .tx_empty = atmel_tx_empty,
2457 .set_mctrl = atmel_set_mctrl,
2458 .get_mctrl = atmel_get_mctrl,
2459 .stop_tx = atmel_stop_tx,
2460 .start_tx = atmel_start_tx,
2461 .stop_rx = atmel_stop_rx,
2462 .enable_ms = atmel_enable_ms,
2463 .break_ctl = atmel_break_ctl,
2464 .startup = atmel_startup,
2465 .shutdown = atmel_shutdown,
2466 .flush_buffer = atmel_flush_buffer,
2467 .set_termios = atmel_set_termios,
2468 .set_ldisc = atmel_set_ldisc,
2469 .type = atmel_type,
2470 .release_port = atmel_release_port,
2471 .request_port = atmel_request_port,
2472 .config_port = atmel_config_port,
2473 .verify_port = atmel_verify_port,
2474 .pm = atmel_serial_pm,
2475#ifdef CONFIG_CONSOLE_POLL
2476 .poll_get_char = atmel_poll_get_char,
2477 .poll_put_char = atmel_poll_put_char,
2478#endif
2479};
2480
2481/*
2482 * Configure the port from the platform device resource info.
2483 */
2484static int atmel_init_port(struct atmel_uart_port *atmel_port,
2485 struct platform_device *pdev)
2486{
2487 int ret;
2488 struct uart_port *port = &atmel_port->uart;
2489 struct platform_device *mpdev = to_platform_device(pdev->dev.parent);
2490
2491 atmel_init_property(atmel_port, pdev);
2492 atmel_set_ops(port);
2493
2494 port->iotype = UPIO_MEM;
2495 port->flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP;
2496 port->ops = &atmel_pops;
2497 port->fifosize = 1;
2498 port->dev = &pdev->dev;
2499 port->mapbase = mpdev->resource[0].start;
2500 port->irq = mpdev->resource[1].start;
2501 port->rs485_config = atmel_config_rs485;
2502 port->iso7816_config = atmel_config_iso7816;
2503 port->membase = NULL;
2504
2505 memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring));
2506
2507 ret = uart_get_rs485_mode(port);
2508 if (ret)
2509 return ret;
2510
2511 /* for console, the clock could already be configured */
2512 if (!atmel_port->clk) {
2513 atmel_port->clk = clk_get(&mpdev->dev, "usart");
2514 if (IS_ERR(atmel_port->clk)) {
2515 ret = PTR_ERR(atmel_port->clk);
2516 atmel_port->clk = NULL;
2517 return ret;
2518 }
2519 ret = clk_prepare_enable(atmel_port->clk);
2520 if (ret) {
2521 clk_put(atmel_port->clk);
2522 atmel_port->clk = NULL;
2523 return ret;
2524 }
2525 port->uartclk = clk_get_rate(atmel_port->clk);
2526 clk_disable_unprepare(atmel_port->clk);
2527 /* only enable clock when USART is in use */
2528 }
2529
2530 /*
2531 * Use TXEMPTY for interrupt when rs485 or ISO7816 else TXRDY or
2532 * ENDTX|TXBUFE
2533 */
2534 if (atmel_uart_is_half_duplex(port))
2535 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
2536 else if (atmel_use_pdc_tx(port)) {
2537 port->fifosize = PDC_BUFFER_SIZE;
2538 atmel_port->tx_done_mask = ATMEL_US_ENDTX | ATMEL_US_TXBUFE;
2539 } else {
2540 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
2541 }
2542
2543 return 0;
2544}
2545
2546#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
2547static void atmel_console_putchar(struct uart_port *port, int ch)
2548{
2549 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY))
2550 cpu_relax();
2551 atmel_uart_write_char(port, ch);
2552}
2553
2554/*
2555 * Interrupts are disabled on entering
2556 */
2557static void atmel_console_write(struct console *co, const char *s, u_int count)
2558{
2559 struct uart_port *port = &atmel_ports[co->index].uart;
2560 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2561 unsigned int status, imr;
2562 unsigned int pdc_tx;
2563
2564 /*
2565 * First, save IMR and then disable interrupts
2566 */
2567 imr = atmel_uart_readl(port, ATMEL_US_IMR);
2568 atmel_uart_writel(port, ATMEL_US_IDR,
2569 ATMEL_US_RXRDY | atmel_port->tx_done_mask);
2570
2571 /* Store PDC transmit status and disable it */
2572 pdc_tx = atmel_uart_readl(port, ATMEL_PDC_PTSR) & ATMEL_PDC_TXTEN;
2573 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
2574
2575 /* Make sure that tx path is actually able to send characters */
2576 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN);
2577 atmel_port->tx_stopped = false;
2578
2579 uart_console_write(port, s, count, atmel_console_putchar);
2580
2581 /*
2582 * Finally, wait for transmitter to become empty
2583 * and restore IMR
2584 */
2585 do {
2586 status = atmel_uart_readl(port, ATMEL_US_CSR);
2587 } while (!(status & ATMEL_US_TXRDY));
2588
2589 /* Restore PDC transmit status */
2590 if (pdc_tx)
2591 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
2592
2593 /* set interrupts back the way they were */
2594 atmel_uart_writel(port, ATMEL_US_IER, imr);
2595}
2596
2597/*
2598 * If the port was already initialised (eg, by a boot loader),
2599 * try to determine the current setup.
2600 */
2601static void __init atmel_console_get_options(struct uart_port *port, int *baud,
2602 int *parity, int *bits)
2603{
2604 unsigned int mr, quot;
2605
2606 /*
2607 * If the baud rate generator isn't running, the port wasn't
2608 * initialized by the boot loader.
2609 */
2610 quot = atmel_uart_readl(port, ATMEL_US_BRGR) & ATMEL_US_CD;
2611 if (!quot)
2612 return;
2613
2614 mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_CHRL;
2615 if (mr == ATMEL_US_CHRL_8)
2616 *bits = 8;
2617 else
2618 *bits = 7;
2619
2620 mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_PAR;
2621 if (mr == ATMEL_US_PAR_EVEN)
2622 *parity = 'e';
2623 else if (mr == ATMEL_US_PAR_ODD)
2624 *parity = 'o';
2625
2626 /*
2627 * The serial core only rounds down when matching this to a
2628 * supported baud rate. Make sure we don't end up slightly
2629 * lower than one of those, as it would make us fall through
2630 * to a much lower baud rate than we really want.
2631 */
2632 *baud = port->uartclk / (16 * (quot - 1));
2633}
2634
2635static int __init atmel_console_setup(struct console *co, char *options)
2636{
2637 int ret;
2638 struct uart_port *port = &atmel_ports[co->index].uart;
2639 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2640 int baud = 115200;
2641 int bits = 8;
2642 int parity = 'n';
2643 int flow = 'n';
2644
2645 if (port->membase == NULL) {
2646 /* Port not initialized yet - delay setup */
2647 return -ENODEV;
2648 }
2649
2650 ret = clk_prepare_enable(atmel_ports[co->index].clk);
2651 if (ret)
2652 return ret;
2653
2654 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2655 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
2656 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
2657 atmel_port->tx_stopped = false;
2658
2659 if (options)
2660 uart_parse_options(options, &baud, &parity, &bits, &flow);
2661 else
2662 atmel_console_get_options(port, &baud, &parity, &bits);
2663
2664 return uart_set_options(port, co, baud, parity, bits, flow);
2665}
2666
2667static struct uart_driver atmel_uart;
2668
2669static struct console atmel_console = {
2670 .name = ATMEL_DEVICENAME,
2671 .write = atmel_console_write,
2672 .device = uart_console_device,
2673 .setup = atmel_console_setup,
2674 .flags = CON_PRINTBUFFER,
2675 .index = -1,
2676 .data = &atmel_uart,
2677};
2678
2679#define ATMEL_CONSOLE_DEVICE (&atmel_console)
2680
2681#else
2682#define ATMEL_CONSOLE_DEVICE NULL
2683#endif
2684
2685static struct uart_driver atmel_uart = {
2686 .owner = THIS_MODULE,
2687 .driver_name = "atmel_serial",
2688 .dev_name = ATMEL_DEVICENAME,
2689 .major = SERIAL_ATMEL_MAJOR,
2690 .minor = MINOR_START,
2691 .nr = ATMEL_MAX_UART,
2692 .cons = ATMEL_CONSOLE_DEVICE,
2693};
2694
2695#ifdef CONFIG_PM
2696static bool atmel_serial_clk_will_stop(void)
2697{
2698#ifdef CONFIG_ARCH_AT91
2699 return at91_suspend_entering_slow_clock();
2700#else
2701 return false;
2702#endif
2703}
2704
2705static int atmel_serial_suspend(struct platform_device *pdev,
2706 pm_message_t state)
2707{
2708 struct uart_port *port = platform_get_drvdata(pdev);
2709 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2710
2711 if (uart_console(port) && console_suspend_enabled) {
2712 /* Drain the TX shifter */
2713 while (!(atmel_uart_readl(port, ATMEL_US_CSR) &
2714 ATMEL_US_TXEMPTY))
2715 cpu_relax();
2716 }
2717
2718 if (uart_console(port) && !console_suspend_enabled) {
2719 /* Cache register values as we won't get a full shutdown/startup
2720 * cycle
2721 */
2722 atmel_port->cache.mr = atmel_uart_readl(port, ATMEL_US_MR);
2723 atmel_port->cache.imr = atmel_uart_readl(port, ATMEL_US_IMR);
2724 atmel_port->cache.brgr = atmel_uart_readl(port, ATMEL_US_BRGR);
2725 atmel_port->cache.rtor = atmel_uart_readl(port,
2726 atmel_port->rtor);
2727 atmel_port->cache.ttgr = atmel_uart_readl(port, ATMEL_US_TTGR);
2728 atmel_port->cache.fmr = atmel_uart_readl(port, ATMEL_US_FMR);
2729 atmel_port->cache.fimr = atmel_uart_readl(port, ATMEL_US_FIMR);
2730 }
2731
2732 /* we can not wake up if we're running on slow clock */
2733 atmel_port->may_wakeup = device_may_wakeup(&pdev->dev);
2734 if (atmel_serial_clk_will_stop()) {
2735 unsigned long flags;
2736
2737 spin_lock_irqsave(&atmel_port->lock_suspended, flags);
2738 atmel_port->suspended = true;
2739 spin_unlock_irqrestore(&atmel_port->lock_suspended, flags);
2740 device_set_wakeup_enable(&pdev->dev, 0);
2741 }
2742
2743 uart_suspend_port(&atmel_uart, port);
2744
2745 return 0;
2746}
2747
2748static int atmel_serial_resume(struct platform_device *pdev)
2749{
2750 struct uart_port *port = platform_get_drvdata(pdev);
2751 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2752 unsigned long flags;
2753
2754 if (uart_console(port) && !console_suspend_enabled) {
2755 atmel_uart_writel(port, ATMEL_US_MR, atmel_port->cache.mr);
2756 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->cache.imr);
2757 atmel_uart_writel(port, ATMEL_US_BRGR, atmel_port->cache.brgr);
2758 atmel_uart_writel(port, atmel_port->rtor,
2759 atmel_port->cache.rtor);
2760 atmel_uart_writel(port, ATMEL_US_TTGR, atmel_port->cache.ttgr);
2761
2762 if (atmel_port->fifo_size) {
2763 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_FIFOEN |
2764 ATMEL_US_RXFCLR | ATMEL_US_TXFLCLR);
2765 atmel_uart_writel(port, ATMEL_US_FMR,
2766 atmel_port->cache.fmr);
2767 atmel_uart_writel(port, ATMEL_US_FIER,
2768 atmel_port->cache.fimr);
2769 }
2770 atmel_start_rx(port);
2771 }
2772
2773 spin_lock_irqsave(&atmel_port->lock_suspended, flags);
2774 if (atmel_port->pending) {
2775 atmel_handle_receive(port, atmel_port->pending);
2776 atmel_handle_status(port, atmel_port->pending,
2777 atmel_port->pending_status);
2778 atmel_handle_transmit(port, atmel_port->pending);
2779 atmel_port->pending = 0;
2780 }
2781 atmel_port->suspended = false;
2782 spin_unlock_irqrestore(&atmel_port->lock_suspended, flags);
2783
2784 uart_resume_port(&atmel_uart, port);
2785 device_set_wakeup_enable(&pdev->dev, atmel_port->may_wakeup);
2786
2787 return 0;
2788}
2789#else
2790#define atmel_serial_suspend NULL
2791#define atmel_serial_resume NULL
2792#endif
2793
2794static void atmel_serial_probe_fifos(struct atmel_uart_port *atmel_port,
2795 struct platform_device *pdev)
2796{
2797 atmel_port->fifo_size = 0;
2798 atmel_port->rts_low = 0;
2799 atmel_port->rts_high = 0;
2800
2801 if (of_property_read_u32(pdev->dev.of_node,
2802 "atmel,fifo-size",
2803 &atmel_port->fifo_size))
2804 return;
2805
2806 if (!atmel_port->fifo_size)
2807 return;
2808
2809 if (atmel_port->fifo_size < ATMEL_MIN_FIFO_SIZE) {
2810 atmel_port->fifo_size = 0;
2811 dev_err(&pdev->dev, "Invalid FIFO size\n");
2812 return;
2813 }
2814
2815 /*
2816 * 0 <= rts_low <= rts_high <= fifo_size
2817 * Once their CTS line asserted by the remote peer, some x86 UARTs tend
2818 * to flush their internal TX FIFO, commonly up to 16 data, before
2819 * actually stopping to send new data. So we try to set the RTS High
2820 * Threshold to a reasonably high value respecting this 16 data
2821 * empirical rule when possible.
2822 */
2823 atmel_port->rts_high = max_t(int, atmel_port->fifo_size >> 1,
2824 atmel_port->fifo_size - ATMEL_RTS_HIGH_OFFSET);
2825 atmel_port->rts_low = max_t(int, atmel_port->fifo_size >> 2,
2826 atmel_port->fifo_size - ATMEL_RTS_LOW_OFFSET);
2827
2828 dev_info(&pdev->dev, "Using FIFO (%u data)\n",
2829 atmel_port->fifo_size);
2830 dev_dbg(&pdev->dev, "RTS High Threshold : %2u data\n",
2831 atmel_port->rts_high);
2832 dev_dbg(&pdev->dev, "RTS Low Threshold : %2u data\n",
2833 atmel_port->rts_low);
2834}
2835
2836static int atmel_serial_probe(struct platform_device *pdev)
2837{
2838 struct atmel_uart_port *atmel_port;
2839 struct device_node *np = pdev->dev.parent->of_node;
2840 void *data;
2841 int ret;
2842 bool rs485_enabled;
2843
2844 BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1));
2845
2846 /*
2847 * In device tree there is no node with "atmel,at91rm9200-usart-serial"
2848 * as compatible string. This driver is probed by at91-usart mfd driver
2849 * which is just a wrapper over the atmel_serial driver and
2850 * spi-at91-usart driver. All attributes needed by this driver are
2851 * found in of_node of parent.
2852 */
2853 pdev->dev.of_node = np;
2854
2855 ret = of_alias_get_id(np, "serial");
2856 if (ret < 0)
2857 /* port id not found in platform data nor device-tree aliases:
2858 * auto-enumerate it */
2859 ret = find_first_zero_bit(atmel_ports_in_use, ATMEL_MAX_UART);
2860
2861 if (ret >= ATMEL_MAX_UART) {
2862 ret = -ENODEV;
2863 goto err;
2864 }
2865
2866 if (test_and_set_bit(ret, atmel_ports_in_use)) {
2867 /* port already in use */
2868 ret = -EBUSY;
2869 goto err;
2870 }
2871
2872 atmel_port = &atmel_ports[ret];
2873 atmel_port->backup_imr = 0;
2874 atmel_port->uart.line = ret;
2875 atmel_port->uart.has_sysrq = IS_ENABLED(CONFIG_SERIAL_ATMEL_CONSOLE);
2876 atmel_serial_probe_fifos(atmel_port, pdev);
2877
2878 atomic_set(&atmel_port->tasklet_shutdown, 0);
2879 spin_lock_init(&atmel_port->lock_suspended);
2880
2881 ret = atmel_init_port(atmel_port, pdev);
2882 if (ret)
2883 goto err_clear_bit;
2884
2885 atmel_port->gpios = mctrl_gpio_init(&atmel_port->uart, 0);
2886 if (IS_ERR(atmel_port->gpios)) {
2887 ret = PTR_ERR(atmel_port->gpios);
2888 goto err_clear_bit;
2889 }
2890
2891 if (!atmel_use_pdc_rx(&atmel_port->uart)) {
2892 ret = -ENOMEM;
2893 data = kmalloc_array(ATMEL_SERIAL_RINGSIZE,
2894 sizeof(struct atmel_uart_char),
2895 GFP_KERNEL);
2896 if (!data)
2897 goto err_alloc_ring;
2898 atmel_port->rx_ring.buf = data;
2899 }
2900
2901 rs485_enabled = atmel_port->uart.rs485.flags & SER_RS485_ENABLED;
2902
2903 ret = uart_add_one_port(&atmel_uart, &atmel_port->uart);
2904 if (ret)
2905 goto err_add_port;
2906
2907#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
2908 if (uart_console(&atmel_port->uart)
2909 && ATMEL_CONSOLE_DEVICE->flags & CON_ENABLED) {
2910 /*
2911 * The serial core enabled the clock for us, so undo
2912 * the clk_prepare_enable() in atmel_console_setup()
2913 */
2914 clk_disable_unprepare(atmel_port->clk);
2915 }
2916#endif
2917
2918 device_init_wakeup(&pdev->dev, 1);
2919 platform_set_drvdata(pdev, atmel_port);
2920
2921 /*
2922 * The peripheral clock has been disabled by atmel_init_port():
2923 * enable it before accessing I/O registers
2924 */
2925 clk_prepare_enable(atmel_port->clk);
2926
2927 if (rs485_enabled) {
2928 atmel_uart_writel(&atmel_port->uart, ATMEL_US_MR,
2929 ATMEL_US_USMODE_NORMAL);
2930 atmel_uart_writel(&atmel_port->uart, ATMEL_US_CR,
2931 ATMEL_US_RTSEN);
2932 }
2933
2934 /*
2935 * Get port name of usart or uart
2936 */
2937 atmel_get_ip_name(&atmel_port->uart);
2938
2939 /*
2940 * The peripheral clock can now safely be disabled till the port
2941 * is used
2942 */
2943 clk_disable_unprepare(atmel_port->clk);
2944
2945 return 0;
2946
2947err_add_port:
2948 kfree(atmel_port->rx_ring.buf);
2949 atmel_port->rx_ring.buf = NULL;
2950err_alloc_ring:
2951 if (!uart_console(&atmel_port->uart)) {
2952 clk_put(atmel_port->clk);
2953 atmel_port->clk = NULL;
2954 }
2955err_clear_bit:
2956 clear_bit(atmel_port->uart.line, atmel_ports_in_use);
2957err:
2958 return ret;
2959}
2960
2961/*
2962 * Even if the driver is not modular, it makes sense to be able to
2963 * unbind a device: there can be many bound devices, and there are
2964 * situations where dynamic binding and unbinding can be useful.
2965 *
2966 * For example, a connected device can require a specific firmware update
2967 * protocol that needs bitbanging on IO lines, but use the regular serial
2968 * port in the normal case.
2969 */
2970static int atmel_serial_remove(struct platform_device *pdev)
2971{
2972 struct uart_port *port = platform_get_drvdata(pdev);
2973 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2974 int ret = 0;
2975
2976 tasklet_kill(&atmel_port->tasklet_rx);
2977 tasklet_kill(&atmel_port->tasklet_tx);
2978
2979 device_init_wakeup(&pdev->dev, 0);
2980
2981 ret = uart_remove_one_port(&atmel_uart, port);
2982
2983 kfree(atmel_port->rx_ring.buf);
2984
2985 /* "port" is allocated statically, so we shouldn't free it */
2986
2987 clear_bit(port->line, atmel_ports_in_use);
2988
2989 clk_put(atmel_port->clk);
2990 atmel_port->clk = NULL;
2991 pdev->dev.of_node = NULL;
2992
2993 return ret;
2994}
2995
2996static struct platform_driver atmel_serial_driver = {
2997 .probe = atmel_serial_probe,
2998 .remove = atmel_serial_remove,
2999 .suspend = atmel_serial_suspend,
3000 .resume = atmel_serial_resume,
3001 .driver = {
3002 .name = "atmel_usart_serial",
3003 .of_match_table = of_match_ptr(atmel_serial_dt_ids),
3004 },
3005};
3006
3007static int __init atmel_serial_init(void)
3008{
3009 int ret;
3010
3011 ret = uart_register_driver(&atmel_uart);
3012 if (ret)
3013 return ret;
3014
3015 ret = platform_driver_register(&atmel_serial_driver);
3016 if (ret)
3017 uart_unregister_driver(&atmel_uart);
3018
3019 return ret;
3020}
3021device_initcall(atmel_serial_init);