Loading...
1#
2# SPI driver configuration
3#
4# NOTE: the reason this doesn't show SPI slave support is mostly that
5# nobody's needed a slave side API yet. The master-role API is not
6# fully appropriate there, so it'd need some thought to do well.
7#
8menuconfig SPI
9 bool "SPI support"
10 depends on HAS_IOMEM
11 help
12 The "Serial Peripheral Interface" is a low level synchronous
13 protocol. Chips that support SPI can have data transfer rates
14 up to several tens of Mbit/sec. Chips are addressed with a
15 controller and a chipselect. Most SPI slaves don't support
16 dynamic device discovery; some are even write-only or read-only.
17
18 SPI is widely used by microcontrollers to talk with sensors,
19 eeprom and flash memory, codecs and various other controller
20 chips, analog to digital (and d-to-a) converters, and more.
21 MMC and SD cards can be accessed using SPI protocol; and for
22 DataFlash cards used in MMC sockets, SPI must always be used.
23
24 SPI is one of a family of similar protocols using a four wire
25 interface (select, clock, data in, data out) including Microwire
26 (half duplex), SSP, SSI, and PSP. This driver framework should
27 work with most such devices and controllers.
28
29if SPI
30
31config SPI_DEBUG
32 bool "Debug support for SPI drivers"
33 depends on DEBUG_KERNEL
34 help
35 Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
36 sysfs, and debugfs support in SPI controller and protocol drivers.
37
38#
39# MASTER side ... talking to discrete SPI slave chips including microcontrollers
40#
41
42config SPI_MASTER
43# bool "SPI Master Support"
44 bool
45 default SPI
46 help
47 If your system has an master-capable SPI controller (which
48 provides the clock and chipselect), you can enable that
49 controller and the protocol drivers for the SPI slave chips
50 that are connected.
51
52if SPI_MASTER
53
54comment "SPI Master Controller Drivers"
55
56config SPI_ALTERA
57 tristate "Altera SPI Controller"
58 select SPI_BITBANG
59 help
60 This is the driver for the Altera SPI Controller.
61
62config SPI_ATH79
63 tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
64 depends on ATH79 && GPIOLIB
65 select SPI_BITBANG
66 help
67 This enables support for the SPI controller present on the
68 Atheros AR71XX/AR724X/AR913X SoCs.
69
70config SPI_ATMEL
71 tristate "Atmel SPI Controller"
72 depends on HAS_DMA
73 depends on (ARCH_AT91 || AVR32 || COMPILE_TEST)
74 help
75 This selects a driver for the Atmel SPI Controller, present on
76 many AT32 (AVR32) and AT91 (ARM) chips.
77
78config SPI_AU1550
79 tristate "Au1550/Au1200/Au1300 SPI Controller"
80 depends on MIPS_ALCHEMY
81 select SPI_BITBANG
82 help
83 If you say yes to this option, support will be included for the
84 PSC SPI controller found on Au1550, Au1200 and Au1300 series.
85
86config SPI_AXI_SPI_ENGINE
87 tristate "Analog Devices AXI SPI Engine controller"
88 depends on HAS_IOMEM
89 help
90 This enables support for the Analog Devices AXI SPI Engine SPI controller.
91 It is part of the SPI Engine framework that is used in some Analog Devices
92 reference designs for FPGAs.
93
94config SPI_BCM2835
95 tristate "BCM2835 SPI controller"
96 depends on GPIOLIB
97 depends on ARCH_BCM2835 || COMPILE_TEST
98 help
99 This selects a driver for the Broadcom BCM2835 SPI master.
100
101 The BCM2835 contains two types of SPI master controller; the
102 "universal SPI master", and the regular SPI controller. This driver
103 is for the regular SPI controller. Slave mode operation is not also
104 not supported.
105
106config SPI_BCM2835AUX
107 tristate "BCM2835 SPI auxiliary controller"
108 depends on (ARCH_BCM2835 && GPIOLIB) || COMPILE_TEST
109 help
110 This selects a driver for the Broadcom BCM2835 SPI aux master.
111
112 The BCM2835 contains two types of SPI master controller; the
113 "universal SPI master", and the regular SPI controller.
114 This driver is for the universal/auxiliary SPI controller.
115
116config SPI_BFIN5XX
117 tristate "SPI controller driver for ADI Blackfin5xx"
118 depends on BLACKFIN && !BF60x
119 help
120 This is the SPI controller master driver for Blackfin 5xx processor.
121
122config SPI_ADI_V3
123 tristate "SPI controller v3 for ADI"
124 depends on BF60x
125 help
126 This is the SPI controller v3 master driver
127 found on Blackfin 60x processor.
128
129config SPI_BFIN_SPORT
130 tristate "SPI bus via Blackfin SPORT"
131 depends on BLACKFIN
132 help
133 Enable support for a SPI bus via the Blackfin SPORT peripheral.
134
135config SPI_BCM53XX
136 tristate "Broadcom BCM53xx SPI controller"
137 depends on ARCH_BCM_5301X
138 depends on BCMA_POSSIBLE
139 select BCMA
140 help
141 Enable support for the SPI controller on Broadcom BCM53xx ARM SoCs.
142
143config SPI_BCM63XX
144 tristate "Broadcom BCM63xx SPI controller"
145 depends on BCM63XX || COMPILE_TEST
146 help
147 Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
148
149config SPI_BCM63XX_HSSPI
150 tristate "Broadcom BCM63XX HS SPI controller driver"
151 depends on BCM63XX || COMPILE_TEST
152 help
153 This enables support for the High Speed SPI controller present on
154 newer Broadcom BCM63XX SoCs.
155
156config SPI_BITBANG
157 tristate "Utilities for Bitbanging SPI masters"
158 help
159 With a few GPIO pins, your system can bitbang the SPI protocol.
160 Select this to get SPI support through I/O pins (GPIO, parallel
161 port, etc). Or, some systems' SPI master controller drivers use
162 this code to manage the per-word or per-transfer accesses to the
163 hardware shift registers.
164
165 This is library code, and is automatically selected by drivers that
166 need it. You only need to select this explicitly to support driver
167 modules that aren't part of this kernel tree.
168
169config SPI_BUTTERFLY
170 tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
171 depends on PARPORT
172 select SPI_BITBANG
173 help
174 This uses a custom parallel port cable to connect to an AVR
175 Butterfly <http://www.atmel.com/products/avr/butterfly>, an
176 inexpensive battery powered microcontroller evaluation board.
177 This same cable can be used to flash new firmware.
178
179config SPI_CADENCE
180 tristate "Cadence SPI controller"
181 help
182 This selects the Cadence SPI controller master driver
183 used by Xilinx Zynq and ZynqMP.
184
185config SPI_CLPS711X
186 tristate "CLPS711X host SPI controller"
187 depends on ARCH_CLPS711X || COMPILE_TEST
188 help
189 This enables dedicated general purpose SPI/Microwire1-compatible
190 master mode interface (SSI1) for CLPS711X-based CPUs.
191
192config SPI_COLDFIRE_QSPI
193 tristate "Freescale Coldfire QSPI controller"
194 depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
195 help
196 This enables support for the Coldfire QSPI controller in master
197 mode.
198
199config SPI_DAVINCI
200 tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
201 depends on ARCH_DAVINCI || ARCH_KEYSTONE
202 select SPI_BITBANG
203 help
204 SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
205
206config SPI_DESIGNWARE
207 tristate "DesignWare SPI controller core support"
208 help
209 general driver for SPI controller core from DesignWare
210
211config SPI_DW_PCI
212 tristate "PCI interface driver for DW SPI core"
213 depends on SPI_DESIGNWARE && PCI
214
215config SPI_DW_MID_DMA
216 bool "DMA support for DW SPI controller on Intel MID platform"
217 depends on SPI_DW_PCI && DW_DMAC_PCI
218
219config SPI_DW_MMIO
220 tristate "Memory-mapped io interface driver for DW SPI core"
221 depends on SPI_DESIGNWARE
222
223config SPI_DLN2
224 tristate "Diolan DLN-2 USB SPI adapter"
225 depends on MFD_DLN2
226 help
227 If you say yes to this option, support will be included for Diolan
228 DLN2, a USB to SPI interface.
229
230 This driver can also be built as a module. If so, the module
231 will be called spi-dln2.
232
233config SPI_EFM32
234 tristate "EFM32 SPI controller"
235 depends on OF && ARM && (ARCH_EFM32 || COMPILE_TEST)
236 select SPI_BITBANG
237 help
238 Driver for the spi controller found on Energy Micro's EFM32 SoCs.
239
240config SPI_EP93XX
241 tristate "Cirrus Logic EP93xx SPI controller"
242 depends on HAS_DMA
243 depends on ARCH_EP93XX || COMPILE_TEST
244 help
245 This enables using the Cirrus EP93xx SPI controller in master
246 mode.
247
248config SPI_FALCON
249 tristate "Falcon SPI controller support"
250 depends on SOC_FALCON
251 help
252 The external bus unit (EBU) found on the FALC-ON SoC has SPI
253 emulation that is designed for serial flash access. This driver
254 has only been tested with m25p80 type chips. The hardware has no
255 support for other types of SPI peripherals.
256
257config SPI_GPIO
258 tristate "GPIO-based bitbanging SPI Master"
259 depends on GPIOLIB || COMPILE_TEST
260 select SPI_BITBANG
261 help
262 This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
263 interface to manage MOSI, MISO, SCK, and chipselect signals. SPI
264 slaves connected to a bus using this driver are configured as usual,
265 except that the spi_board_info.controller_data holds the GPIO number
266 for the chipselect used by this controller driver.
267
268 Note that this driver often won't achieve even 1 Mbit/sec speeds,
269 making it unusually slow for SPI. If your platform can inline
270 GPIO operations, you should be able to leverage that for better
271 speed with a custom version of this driver; see the source code.
272
273config SPI_IMG_SPFI
274 tristate "IMG SPFI controller"
275 depends on MIPS || COMPILE_TEST
276 help
277 This enables support for the SPFI master controller found on
278 IMG SoCs.
279
280config SPI_IMX
281 tristate "Freescale i.MX SPI controllers"
282 depends on ARCH_MXC || COMPILE_TEST
283 select SPI_BITBANG
284 help
285 This enables using the Freescale i.MX SPI controllers in master
286 mode.
287
288config SPI_LM70_LLP
289 tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
290 depends on PARPORT
291 select SPI_BITBANG
292 help
293 This driver supports the NS LM70 LLP Evaluation Board,
294 which interfaces to an LM70 temperature sensor using
295 a parallel port.
296
297config SPI_LP8841_RTC
298 tristate "ICP DAS LP-8841 SPI Controller for RTC"
299 depends on MACH_PXA27X_DT || COMPILE_TEST
300 help
301 This driver provides an SPI master device to drive Maxim
302 DS-1302 real time clock.
303
304 Say N here unless you plan to run the kernel on an ICP DAS
305 LP-8x4x industrial computer.
306
307config SPI_MPC52xx
308 tristate "Freescale MPC52xx SPI (non-PSC) controller support"
309 depends on PPC_MPC52xx
310 help
311 This drivers supports the MPC52xx SPI controller in master SPI
312 mode.
313
314config SPI_MPC52xx_PSC
315 tristate "Freescale MPC52xx PSC SPI controller"
316 depends on PPC_MPC52xx
317 help
318 This enables using the Freescale MPC52xx Programmable Serial
319 Controller in master SPI mode.
320
321config SPI_MPC512x_PSC
322 tristate "Freescale MPC512x PSC SPI controller"
323 depends on PPC_MPC512x
324 help
325 This enables using the Freescale MPC5121 Programmable Serial
326 Controller in SPI master mode.
327
328config SPI_FSL_LIB
329 tristate
330 depends on OF
331
332config SPI_FSL_CPM
333 tristate
334 depends on FSL_SOC
335
336config SPI_FSL_SPI
337 tristate "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller"
338 depends on OF
339 select SPI_FSL_LIB
340 select SPI_FSL_CPM if FSL_SOC
341 help
342 This enables using the Freescale SPI controllers in master mode.
343 MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
344 MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
345 This also enables using the Aeroflex Gaisler GRLIB SPI controller in
346 master mode.
347
348config SPI_FSL_DSPI
349 tristate "Freescale DSPI controller"
350 select REGMAP_MMIO
351 depends on SOC_VF610 || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
352 help
353 This enables support for the Freescale DSPI controller in master
354 mode. VF610 platform uses the controller.
355
356config SPI_FSL_ESPI
357 tristate "Freescale eSPI controller"
358 depends on FSL_SOC
359 select SPI_FSL_LIB
360 help
361 This enables using the Freescale eSPI controllers in master mode.
362 From MPC8536, 85xx platform uses the controller, and all P10xx,
363 P20xx, P30xx,P40xx, P50xx uses this controller.
364
365config SPI_MESON_SPIFC
366 tristate "Amlogic Meson SPIFC controller"
367 depends on ARCH_MESON || COMPILE_TEST
368 select REGMAP_MMIO
369 help
370 This enables master mode support for the SPIFC (SPI flash
371 controller) available in Amlogic Meson SoCs.
372
373config SPI_MT65XX
374 tristate "MediaTek SPI controller"
375 depends on ARCH_MEDIATEK || COMPILE_TEST
376 help
377 This selects the MediaTek(R) SPI bus driver.
378 If you want to use MediaTek(R) SPI interface,
379 say Y or M here.If you are not sure, say N.
380 SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.
381
382config SPI_NUC900
383 tristate "Nuvoton NUC900 series SPI"
384 depends on ARCH_W90X900
385 select SPI_BITBANG
386 help
387 SPI driver for Nuvoton NUC900 series ARM SoCs
388
389config SPI_OC_TINY
390 tristate "OpenCores tiny SPI"
391 depends on GPIOLIB || COMPILE_TEST
392 select SPI_BITBANG
393 help
394 This is the driver for OpenCores tiny SPI master controller.
395
396config SPI_OCTEON
397 tristate "Cavium OCTEON SPI controller"
398 depends on CAVIUM_OCTEON_SOC
399 help
400 SPI host driver for the hardware found on some Cavium OCTEON
401 SOCs.
402
403config SPI_OMAP_UWIRE
404 tristate "OMAP1 MicroWire"
405 depends on ARCH_OMAP1
406 select SPI_BITBANG
407 help
408 This hooks up to the MicroWire controller on OMAP1 chips.
409
410config SPI_OMAP24XX
411 tristate "McSPI driver for OMAP"
412 depends on HAS_DMA
413 depends on ARM || ARM64 || AVR32 || HEXAGON || MIPS || SUPERH
414 depends on ARCH_OMAP2PLUS || COMPILE_TEST
415 help
416 SPI master controller for OMAP24XX and later Multichannel SPI
417 (McSPI) modules.
418
419config SPI_TI_QSPI
420 tristate "DRA7xxx QSPI controller support"
421 depends on ARCH_OMAP2PLUS || COMPILE_TEST
422 help
423 QSPI master controller for DRA7xxx used for flash devices.
424 This device supports single, dual and quad read support, while
425 it only supports single write mode.
426
427config SPI_OMAP_100K
428 tristate "OMAP SPI 100K"
429 depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST
430 help
431 OMAP SPI 100K master controller for omap7xx boards.
432
433config SPI_ORION
434 tristate "Orion SPI master"
435 depends on PLAT_ORION || COMPILE_TEST
436 help
437 This enables using the SPI master controller on the Orion chips.
438
439config SPI_PL022
440 tristate "ARM AMBA PL022 SSP controller"
441 depends on ARM_AMBA
442 default y if MACH_U300
443 default y if ARCH_REALVIEW
444 default y if INTEGRATOR_IMPD1
445 default y if ARCH_VERSATILE
446 help
447 This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
448 controller. If you have an embedded system with an AMBA(R)
449 bus and a PL022 controller, say Y or M here.
450
451config SPI_PPC4xx
452 tristate "PPC4xx SPI Controller"
453 depends on PPC32 && 4xx
454 select SPI_BITBANG
455 help
456 This selects a driver for the PPC4xx SPI Controller.
457
458config SPI_PXA2XX
459 tristate "PXA2xx SSP SPI master"
460 depends on (ARCH_PXA || PCI || ACPI)
461 select PXA_SSP if ARCH_PXA
462 help
463 This enables using a PXA2xx or Sodaville SSP port as a SPI master
464 controller. The driver can be configured to use any SSP port and
465 additional documentation can be found a Documentation/spi/pxa2xx.
466
467config SPI_PXA2XX_PCI
468 def_tristate SPI_PXA2XX && PCI && COMMON_CLK
469
470config SPI_ROCKCHIP
471 tristate "Rockchip SPI controller driver"
472 depends on ARM || ARM64 || AVR32 || HEXAGON || MIPS || SUPERH
473 help
474 This selects a driver for Rockchip SPI controller.
475
476 If you say yes to this option, support will be included for
477 RK3066, RK3188 and RK3288 families of SPI controller.
478 Rockchip SPI controller support DMA transport and PIO mode.
479 The main usecase of this controller is to use spi flash as boot
480 device.
481
482config SPI_RB4XX
483 tristate "Mikrotik RB4XX SPI master"
484 depends on SPI_MASTER && ATH79
485 help
486 SPI controller driver for the Mikrotik RB4xx series boards.
487
488config SPI_RSPI
489 tristate "Renesas RSPI/QSPI controller"
490 depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
491 help
492 SPI driver for Renesas RSPI and QSPI blocks.
493
494config SPI_QUP
495 tristate "Qualcomm SPI controller with QUP interface"
496 depends on ARCH_QCOM || (ARM && COMPILE_TEST)
497 help
498 Qualcomm Universal Peripheral (QUP) core is an AHB slave that
499 provides a common data path (an output FIFO and an input FIFO)
500 for serial peripheral interface (SPI) mini-core. SPI in master
501 mode supports up to 50MHz, up to four chip selects, programmable
502 data path from 4 bits to 32 bits and numerous protocol variants.
503
504 This driver can also be built as a module. If so, the module
505 will be called spi_qup.
506
507config SPI_S3C24XX
508 tristate "Samsung S3C24XX series SPI"
509 depends on ARCH_S3C24XX
510 select SPI_BITBANG
511 help
512 SPI driver for Samsung S3C24XX series ARM SoCs
513
514config SPI_S3C24XX_FIQ
515 bool "S3C24XX driver with FIQ pseudo-DMA"
516 depends on SPI_S3C24XX
517 select FIQ
518 help
519 Enable FIQ support for the S3C24XX SPI driver to provide pseudo
520 DMA by using the fast-interrupt request framework, This allows
521 the driver to get DMA-like performance when there are either
522 no free DMA channels, or when doing transfers that required both
523 TX and RX data paths.
524
525config SPI_S3C64XX
526 tristate "Samsung S3C64XX series type SPI"
527 depends on (PLAT_SAMSUNG || ARCH_EXYNOS)
528 help
529 SPI driver for Samsung S3C64XX and newer SoCs.
530
531config SPI_SC18IS602
532 tristate "NXP SC18IS602/602B/603 I2C to SPI bridge"
533 depends on I2C
534 help
535 SPI driver for NXP SC18IS602/602B/603 I2C to SPI bridge.
536
537config SPI_SH_MSIOF
538 tristate "SuperH MSIOF SPI controller"
539 depends on HAVE_CLK && HAS_DMA
540 depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
541 help
542 SPI driver for SuperH and SH Mobile MSIOF blocks.
543
544config SPI_SH
545 tristate "SuperH SPI controller"
546 depends on SUPERH || COMPILE_TEST
547 help
548 SPI driver for SuperH SPI blocks.
549
550config SPI_SH_SCI
551 tristate "SuperH SCI SPI controller"
552 depends on SUPERH
553 select SPI_BITBANG
554 help
555 SPI driver for SuperH SCI blocks.
556
557config SPI_SH_HSPI
558 tristate "SuperH HSPI controller"
559 depends on ARCH_RENESAS || COMPILE_TEST
560 help
561 SPI driver for SuperH HSPI blocks.
562
563config SPI_SIRF
564 tristate "CSR SiRFprimaII SPI controller"
565 depends on SIRF_DMA
566 select SPI_BITBANG
567 help
568 SPI driver for CSR SiRFprimaII SoCs
569
570config SPI_ST_SSC4
571 tristate "STMicroelectronics SPI SSC-based driver"
572 depends on ARCH_STI
573 help
574 STMicroelectronics SoCs support for SPI. If you say yes to
575 this option, support will be included for the SSC driven SPI.
576
577config SPI_SUN4I
578 tristate "Allwinner A10 SoCs SPI controller"
579 depends on ARCH_SUNXI || COMPILE_TEST
580 help
581 SPI driver for Allwinner sun4i, sun5i and sun7i SoCs
582
583config SPI_SUN6I
584 tristate "Allwinner A31 SPI controller"
585 depends on ARCH_SUNXI || COMPILE_TEST
586 depends on RESET_CONTROLLER
587 help
588 This enables using the SPI controller on the Allwinner A31 SoCs.
589
590config SPI_MXS
591 tristate "Freescale MXS SPI controller"
592 depends on ARCH_MXS
593 select STMP_DEVICE
594 help
595 SPI driver for Freescale MXS devices.
596
597config SPI_TEGRA114
598 tristate "NVIDIA Tegra114 SPI Controller"
599 depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
600 depends on RESET_CONTROLLER && HAS_DMA
601 help
602 SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller
603 is different than the older SoCs SPI controller and also register interface
604 get changed with this controller.
605
606config SPI_TEGRA20_SFLASH
607 tristate "Nvidia Tegra20 Serial flash Controller"
608 depends on ARCH_TEGRA || COMPILE_TEST
609 depends on RESET_CONTROLLER
610 help
611 SPI driver for Nvidia Tegra20 Serial flash Controller interface.
612 The main usecase of this controller is to use spi flash as boot
613 device.
614
615config SPI_TEGRA20_SLINK
616 tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
617 depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
618 depends on RESET_CONTROLLER && HAS_DMA
619 help
620 SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
621
622config SPI_TOPCLIFF_PCH
623 tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
624 depends on PCI && (X86_32 || MIPS || COMPILE_TEST)
625 help
626 SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
627 used in some x86 embedded processors.
628
629 This driver also supports the ML7213/ML7223/ML7831, a companion chip
630 for the Atom E6xx series and compatible with the Intel EG20T PCH.
631
632config SPI_TXX9
633 tristate "Toshiba TXx9 SPI controller"
634 depends on GPIOLIB && (CPU_TX49XX || COMPILE_TEST)
635 help
636 SPI driver for Toshiba TXx9 MIPS SoCs
637
638config SPI_XCOMM
639 tristate "Analog Devices AD-FMCOMMS1-EBZ SPI-I2C-bridge driver"
640 depends on I2C
641 help
642 Support for the SPI-I2C bridge found on the Analog Devices
643 AD-FMCOMMS1-EBZ board.
644
645config SPI_XILINX
646 tristate "Xilinx SPI controller common module"
647 depends on HAS_IOMEM
648 select SPI_BITBANG
649 help
650 This exposes the SPI controller IP from the Xilinx EDK.
651
652 See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
653 Product Specification document (DS464) for hardware details.
654
655 Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
656
657config SPI_XLP
658 tristate "Netlogic XLP SPI controller driver"
659 depends on CPU_XLP || COMPILE_TEST
660 help
661 Enable support for the SPI controller on the Netlogic XLP SoCs.
662 Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX, XLP9XX
663 and XLP5XX.
664
665 If you have a Netlogic XLP platform say Y here.
666 If unsure, say N.
667
668config SPI_XTENSA_XTFPGA
669 tristate "Xtensa SPI controller for xtfpga"
670 depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST
671 select SPI_BITBANG
672 help
673 SPI driver for xtfpga SPI master controller.
674
675 This simple SPI master controller is built into xtfpga bitstreams
676 and is used to control daughterboard audio codec. It always transfers
677 16 bit words in SPI mode 0, automatically asserting CS on transfer
678 start and deasserting on end.
679
680config SPI_ZYNQMP_GQSPI
681 tristate "Xilinx ZynqMP GQSPI controller"
682 depends on SPI_MASTER && HAS_DMA
683 help
684 Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.
685
686#
687# Add new SPI master controllers in alphabetical order above this line
688#
689
690#
691# There are lots of SPI device types, with sensors and memory
692# being probably the most widely used ones.
693#
694comment "SPI Protocol Masters"
695
696config SPI_SPIDEV
697 tristate "User mode SPI device driver support"
698 help
699 This supports user mode SPI protocol drivers.
700
701 Note that this application programming interface is EXPERIMENTAL
702 and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
703
704config SPI_LOOPBACK_TEST
705 tristate "spi loopback test framework support"
706 depends on m
707 help
708 This enables the SPI loopback testing framework driver
709
710 primarily used for development of spi_master drivers
711 and to detect regressions
712
713config SPI_TLE62X0
714 tristate "Infineon TLE62X0 (for power switching)"
715 depends on SYSFS
716 help
717 SPI driver for Infineon TLE62X0 series line driver chips,
718 such as the TLE6220, TLE6230 and TLE6240. This provides a
719 sysfs interface, with each line presented as a kind of GPIO
720 exposing both switch control and diagnostic feedback.
721
722#
723# Add new SPI protocol masters in alphabetical order above this line
724#
725
726endif # SPI_MASTER
727
728# (slave support would go here)
729
730endif # SPI
1# SPDX-License-Identifier: GPL-2.0-only
2#
3# SPI driver configuration
4#
5menuconfig SPI
6 bool "SPI support"
7 depends on HAS_IOMEM
8 help
9 The "Serial Peripheral Interface" is a low level synchronous
10 protocol. Chips that support SPI can have data transfer rates
11 up to several tens of Mbit/sec. Chips are addressed with a
12 controller and a chipselect. Most SPI slaves don't support
13 dynamic device discovery; some are even write-only or read-only.
14
15 SPI is widely used by microcontrollers to talk with sensors,
16 eeprom and flash memory, codecs and various other controller
17 chips, analog to digital (and d-to-a) converters, and more.
18 MMC and SD cards can be accessed using SPI protocol; and for
19 DataFlash cards used in MMC sockets, SPI must always be used.
20
21 SPI is one of a family of similar protocols using a four wire
22 interface (select, clock, data in, data out) including Microwire
23 (half duplex), SSP, SSI, and PSP. This driver framework should
24 work with most such devices and controllers.
25
26if SPI
27
28config SPI_DEBUG
29 bool "Debug support for SPI drivers"
30 depends on DEBUG_KERNEL
31 help
32 Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
33 sysfs, and debugfs support in SPI controller and protocol drivers.
34
35#
36# MASTER side ... talking to discrete SPI slave chips including microcontrollers
37#
38
39config SPI_MASTER
40# bool "SPI Master Support"
41 bool
42 default SPI
43 help
44 If your system has an master-capable SPI controller (which
45 provides the clock and chipselect), you can enable that
46 controller and the protocol drivers for the SPI slave chips
47 that are connected.
48
49if SPI_MASTER
50
51config SPI_MEM
52 bool "SPI memory extension"
53 help
54 Enable this option if you want to enable the SPI memory extension.
55 This extension is meant to simplify interaction with SPI memories
56 by providing a high-level interface to send memory-like commands.
57
58comment "SPI Master Controller Drivers"
59
60config SPI_ALTERA
61 tristate "Altera SPI Controller"
62 help
63 This is the driver for the Altera SPI Controller.
64
65config SPI_ATH79
66 tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
67 depends on ATH79 || COMPILE_TEST
68 select SPI_BITBANG
69 help
70 This enables support for the SPI controller present on the
71 Atheros AR71XX/AR724X/AR913X SoCs.
72
73config SPI_ARMADA_3700
74 tristate "Marvell Armada 3700 SPI Controller"
75 depends on (ARCH_MVEBU && OF) || COMPILE_TEST
76 help
77 This enables support for the SPI controller present on the
78 Marvell Armada 3700 SoCs.
79
80config SPI_ATMEL
81 tristate "Atmel SPI Controller"
82 depends on ARCH_AT91 || COMPILE_TEST
83 help
84 This selects a driver for the Atmel SPI Controller, present on
85 many AT91 ARM chips.
86
87config SPI_AT91_USART
88 tristate "Atmel USART Controller SPI driver"
89 depends on (ARCH_AT91 || COMPILE_TEST)
90 depends on MFD_AT91_USART
91 help
92 This selects a driver for the AT91 USART Controller as SPI Master,
93 present on AT91 and SAMA5 SoC series.
94
95config SPI_ATMEL_QUADSPI
96 tristate "Atmel Quad SPI Controller"
97 depends on ARCH_AT91 || (ARM && COMPILE_TEST && !ARCH_EBSA110)
98 depends on OF && HAS_IOMEM
99 help
100 This enables support for the Quad SPI controller in master mode.
101 This driver does not support generic SPI. The implementation only
102 supports spi-mem interface.
103
104config SPI_AU1550
105 tristate "Au1550/Au1200/Au1300 SPI Controller"
106 depends on MIPS_ALCHEMY
107 select SPI_BITBANG
108 help
109 If you say yes to this option, support will be included for the
110 PSC SPI controller found on Au1550, Au1200 and Au1300 series.
111
112config SPI_AXI_SPI_ENGINE
113 tristate "Analog Devices AXI SPI Engine controller"
114 depends on HAS_IOMEM
115 help
116 This enables support for the Analog Devices AXI SPI Engine SPI controller.
117 It is part of the SPI Engine framework that is used in some Analog Devices
118 reference designs for FPGAs.
119
120config SPI_BCM2835
121 tristate "BCM2835 SPI controller"
122 depends on GPIOLIB
123 depends on ARCH_BCM2835 || ARCH_BRCMSTB || COMPILE_TEST
124 help
125 This selects a driver for the Broadcom BCM2835 SPI master.
126
127 The BCM2835 contains two types of SPI master controller; the
128 "universal SPI master", and the regular SPI controller. This driver
129 is for the regular SPI controller. Slave mode operation is not also
130 not supported.
131
132config SPI_BCM2835AUX
133 tristate "BCM2835 SPI auxiliary controller"
134 depends on ((ARCH_BCM2835 || ARCH_BRCMSTB) && GPIOLIB) || COMPILE_TEST
135 help
136 This selects a driver for the Broadcom BCM2835 SPI aux master.
137
138 The BCM2835 contains two types of SPI master controller; the
139 "universal SPI master", and the regular SPI controller.
140 This driver is for the universal/auxiliary SPI controller.
141
142config SPI_BCM63XX
143 tristate "Broadcom BCM63xx SPI controller"
144 depends on BCM63XX || COMPILE_TEST
145 help
146 Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
147
148config SPI_BCM63XX_HSSPI
149 tristate "Broadcom BCM63XX HS SPI controller driver"
150 depends on BCM63XX || ARCH_BCM_63XX || COMPILE_TEST
151 help
152 This enables support for the High Speed SPI controller present on
153 newer Broadcom BCM63XX SoCs.
154
155config SPI_BCM_QSPI
156 tristate "Broadcom BSPI and MSPI controller support"
157 depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || \
158 BMIPS_GENERIC || COMPILE_TEST
159 default ARCH_BCM_IPROC
160 help
161 Enables support for the Broadcom SPI flash and MSPI controller.
162 Select this option for any one of BRCMSTB, iProc NSP and NS2 SoCs
163 based platforms. This driver works for both SPI master for spi-nor
164 flash device as well as MSPI device.
165
166config SPI_BITBANG
167 tristate "Utilities for Bitbanging SPI masters"
168 help
169 With a few GPIO pins, your system can bitbang the SPI protocol.
170 Select this to get SPI support through I/O pins (GPIO, parallel
171 port, etc). Or, some systems' SPI master controller drivers use
172 this code to manage the per-word or per-transfer accesses to the
173 hardware shift registers.
174
175 This is library code, and is automatically selected by drivers that
176 need it. You only need to select this explicitly to support driver
177 modules that aren't part of this kernel tree.
178
179config SPI_BUTTERFLY
180 tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
181 depends on PARPORT
182 select SPI_BITBANG
183 help
184 This uses a custom parallel port cable to connect to an AVR
185 Butterfly <http://www.atmel.com/products/avr/butterfly>, an
186 inexpensive battery powered microcontroller evaluation board.
187 This same cable can be used to flash new firmware.
188
189config SPI_CADENCE
190 tristate "Cadence SPI controller"
191 help
192 This selects the Cadence SPI controller master driver
193 used by Xilinx Zynq and ZynqMP.
194
195config SPI_CLPS711X
196 tristate "CLPS711X host SPI controller"
197 depends on ARCH_CLPS711X || COMPILE_TEST
198 help
199 This enables dedicated general purpose SPI/Microwire1-compatible
200 master mode interface (SSI1) for CLPS711X-based CPUs.
201
202config SPI_COLDFIRE_QSPI
203 tristate "Freescale Coldfire QSPI controller"
204 depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
205 help
206 This enables support for the Coldfire QSPI controller in master
207 mode.
208
209config SPI_DAVINCI
210 tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
211 depends on ARCH_DAVINCI || ARCH_KEYSTONE
212 select SPI_BITBANG
213 help
214 SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
215
216config SPI_DESIGNWARE
217 tristate "DesignWare SPI controller core support"
218 help
219 general driver for SPI controller core from DesignWare
220
221config SPI_DW_PCI
222 tristate "PCI interface driver for DW SPI core"
223 depends on SPI_DESIGNWARE && PCI
224
225config SPI_DW_MID_DMA
226 bool "DMA support for DW SPI controller on Intel MID platform"
227 depends on SPI_DW_PCI && DW_DMAC_PCI
228
229config SPI_DW_MMIO
230 tristate "Memory-mapped io interface driver for DW SPI core"
231 depends on SPI_DESIGNWARE
232
233config SPI_DLN2
234 tristate "Diolan DLN-2 USB SPI adapter"
235 depends on MFD_DLN2
236 help
237 If you say yes to this option, support will be included for Diolan
238 DLN2, a USB to SPI interface.
239
240 This driver can also be built as a module. If so, the module
241 will be called spi-dln2.
242
243config SPI_EFM32
244 tristate "EFM32 SPI controller"
245 depends on OF && ARM && (ARCH_EFM32 || COMPILE_TEST)
246 select SPI_BITBANG
247 help
248 Driver for the spi controller found on Energy Micro's EFM32 SoCs.
249
250config SPI_EP93XX
251 tristate "Cirrus Logic EP93xx SPI controller"
252 depends on ARCH_EP93XX || COMPILE_TEST
253 help
254 This enables using the Cirrus EP93xx SPI controller in master
255 mode.
256
257config SPI_FALCON
258 bool "Falcon SPI controller support"
259 depends on SOC_FALCON
260 help
261 The external bus unit (EBU) found on the FALC-ON SoC has SPI
262 emulation that is designed for serial flash access. This driver
263 has only been tested with m25p80 type chips. The hardware has no
264 support for other types of SPI peripherals.
265
266config SPI_FSL_LPSPI
267 tristate "Freescale i.MX LPSPI controller"
268 depends on ARCH_MXC || COMPILE_TEST
269 help
270 This enables Freescale i.MX LPSPI controllers in master mode.
271
272config SPI_FSL_QUADSPI
273 tristate "Freescale QSPI controller"
274 depends on ARCH_MXC || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
275 depends on HAS_IOMEM
276 help
277 This enables support for the Quad SPI controller in master mode.
278 Up to four flash chips can be connected on two buses with two
279 chipselects each.
280 This controller does not support generic SPI messages. It only
281 supports the high-level SPI memory interface.
282
283config SPI_NXP_FLEXSPI
284 tristate "NXP Flex SPI controller"
285 depends on ARCH_LAYERSCAPE || HAS_IOMEM
286 help
287 This enables support for the Flex SPI controller in master mode.
288 Up to four slave devices can be connected on two buses with two
289 chipselects each.
290 This controller does not support generic SPI messages and only
291 supports the high-level SPI memory interface.
292
293config SPI_GPIO
294 tristate "GPIO-based bitbanging SPI Master"
295 depends on GPIOLIB || COMPILE_TEST
296 select SPI_BITBANG
297 help
298 This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
299 interface to manage MOSI, MISO, SCK, and chipselect signals. SPI
300 slaves connected to a bus using this driver are configured as usual,
301 except that the spi_board_info.controller_data holds the GPIO number
302 for the chipselect used by this controller driver.
303
304 Note that this driver often won't achieve even 1 Mbit/sec speeds,
305 making it unusually slow for SPI. If your platform can inline
306 GPIO operations, you should be able to leverage that for better
307 speed with a custom version of this driver; see the source code.
308
309config SPI_IMG_SPFI
310 tristate "IMG SPFI controller"
311 depends on MIPS || COMPILE_TEST
312 help
313 This enables support for the SPFI master controller found on
314 IMG SoCs.
315
316config SPI_IMX
317 tristate "Freescale i.MX SPI controllers"
318 depends on ARCH_MXC || COMPILE_TEST
319 select SPI_BITBANG
320 help
321 This enables support for the Freescale i.MX SPI controllers.
322
323config SPI_JCORE
324 tristate "J-Core SPI Master"
325 depends on OF && (SUPERH || COMPILE_TEST)
326 help
327 This enables support for the SPI master controller in the J-Core
328 synthesizable, open source SoC.
329
330config SPI_LM70_LLP
331 tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
332 depends on PARPORT
333 select SPI_BITBANG
334 help
335 This driver supports the NS LM70 LLP Evaluation Board,
336 which interfaces to an LM70 temperature sensor using
337 a parallel port.
338
339config SPI_LP8841_RTC
340 tristate "ICP DAS LP-8841 SPI Controller for RTC"
341 depends on MACH_PXA27X_DT || COMPILE_TEST
342 help
343 This driver provides an SPI master device to drive Maxim
344 DS-1302 real time clock.
345
346 Say N here unless you plan to run the kernel on an ICP DAS
347 LP-8x4x industrial computer.
348
349config SPI_MPC52xx
350 tristate "Freescale MPC52xx SPI (non-PSC) controller support"
351 depends on PPC_MPC52xx
352 help
353 This drivers supports the MPC52xx SPI controller in master SPI
354 mode.
355
356config SPI_MPC52xx_PSC
357 tristate "Freescale MPC52xx PSC SPI controller"
358 depends on PPC_MPC52xx
359 help
360 This enables using the Freescale MPC52xx Programmable Serial
361 Controller in master SPI mode.
362
363config SPI_MPC512x_PSC
364 tristate "Freescale MPC512x PSC SPI controller"
365 depends on PPC_MPC512x
366 help
367 This enables using the Freescale MPC5121 Programmable Serial
368 Controller in SPI master mode.
369
370config SPI_FSL_LIB
371 tristate
372 depends on OF
373
374config SPI_FSL_CPM
375 tristate
376 depends on FSL_SOC
377
378config SPI_FSL_SPI
379 tristate "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller"
380 depends on OF
381 select SPI_FSL_LIB
382 select SPI_FSL_CPM if FSL_SOC
383 help
384 This enables using the Freescale SPI controllers in master mode.
385 MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
386 MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
387 This also enables using the Aeroflex Gaisler GRLIB SPI controller in
388 master mode.
389
390config SPI_FSL_DSPI
391 tristate "Freescale DSPI controller"
392 select REGMAP_MMIO
393 depends on SOC_VF610 || SOC_LS1021A || ARCH_LAYERSCAPE || M5441x || COMPILE_TEST
394 help
395 This enables support for the Freescale DSPI controller in master
396 mode. VF610, LS1021A and ColdFire platforms uses the controller.
397
398config SPI_FSL_ESPI
399 tristate "Freescale eSPI controller"
400 depends on FSL_SOC
401 help
402 This enables using the Freescale eSPI controllers in master mode.
403 From MPC8536, 85xx platform uses the controller, and all P10xx,
404 P20xx, P30xx,P40xx, P50xx uses this controller.
405
406config SPI_MESON_SPICC
407 tristate "Amlogic Meson SPICC controller"
408 depends on ARCH_MESON || COMPILE_TEST
409 help
410 This enables master mode support for the SPICC (SPI communication
411 controller) available in Amlogic Meson SoCs.
412
413config SPI_MESON_SPIFC
414 tristate "Amlogic Meson SPIFC controller"
415 depends on ARCH_MESON || COMPILE_TEST
416 select REGMAP_MMIO
417 help
418 This enables master mode support for the SPIFC (SPI flash
419 controller) available in Amlogic Meson SoCs.
420
421config SPI_MT65XX
422 tristate "MediaTek SPI controller"
423 depends on ARCH_MEDIATEK || COMPILE_TEST
424 help
425 This selects the MediaTek(R) SPI bus driver.
426 If you want to use MediaTek(R) SPI interface,
427 say Y or M here.If you are not sure, say N.
428 SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.
429
430config SPI_MT7621
431 tristate "MediaTek MT7621 SPI Controller"
432 depends on RALINK || COMPILE_TEST
433 help
434 This selects a driver for the MediaTek MT7621 SPI Controller.
435
436config SPI_NPCM_FIU
437 tristate "Nuvoton NPCM FLASH Interface Unit"
438 depends on ARCH_NPCM || COMPILE_TEST
439 depends on OF && HAS_IOMEM
440 help
441 This enables support for the Flash Interface Unit SPI controller
442 in master mode.
443 This driver does not support generic SPI. The implementation only
444 supports spi-mem interface.
445
446config SPI_NPCM_PSPI
447 tristate "Nuvoton NPCM PSPI Controller"
448 depends on ARCH_NPCM || COMPILE_TEST
449 help
450 This driver provides support for Nuvoton NPCM BMC
451 Peripheral SPI controller in master mode.
452
453config SPI_LANTIQ_SSC
454 tristate "Lantiq SSC SPI controller"
455 depends on LANTIQ || COMPILE_TEST
456 help
457 This driver supports the Lantiq SSC SPI controller in master
458 mode. This controller is found on Intel (former Lantiq) SoCs like
459 the Danube, Falcon, xRX200, xRX300.
460
461config SPI_OC_TINY
462 tristate "OpenCores tiny SPI"
463 depends on GPIOLIB || COMPILE_TEST
464 select SPI_BITBANG
465 help
466 This is the driver for OpenCores tiny SPI master controller.
467
468config SPI_OCTEON
469 tristate "Cavium OCTEON SPI controller"
470 depends on CAVIUM_OCTEON_SOC
471 help
472 SPI host driver for the hardware found on some Cavium OCTEON
473 SOCs.
474
475config SPI_OMAP_UWIRE
476 tristate "OMAP1 MicroWire"
477 depends on ARCH_OMAP1
478 select SPI_BITBANG
479 help
480 This hooks up to the MicroWire controller on OMAP1 chips.
481
482config SPI_OMAP24XX
483 tristate "McSPI driver for OMAP"
484 depends on ARCH_OMAP2PLUS || ARCH_K3 || COMPILE_TEST
485 select SG_SPLIT
486 help
487 SPI master controller for OMAP24XX and later Multichannel SPI
488 (McSPI) modules.
489
490config SPI_TI_QSPI
491 tristate "DRA7xxx QSPI controller support"
492 depends on ARCH_OMAP2PLUS || COMPILE_TEST
493 help
494 QSPI master controller for DRA7xxx used for flash devices.
495 This device supports single, dual and quad read support, while
496 it only supports single write mode.
497
498config SPI_OMAP_100K
499 tristate "OMAP SPI 100K"
500 depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST
501 help
502 OMAP SPI 100K master controller for omap7xx boards.
503
504config SPI_ORION
505 tristate "Orion SPI master"
506 depends on PLAT_ORION || ARCH_MVEBU || COMPILE_TEST
507 help
508 This enables using the SPI master controller on the Orion
509 and MVEBU chips.
510
511config SPI_PIC32
512 tristate "Microchip PIC32 series SPI"
513 depends on MACH_PIC32 || COMPILE_TEST
514 help
515 SPI driver for Microchip PIC32 SPI master controller.
516
517config SPI_PIC32_SQI
518 tristate "Microchip PIC32 Quad SPI driver"
519 depends on MACH_PIC32 || COMPILE_TEST
520 help
521 SPI driver for PIC32 Quad SPI controller.
522
523config SPI_PL022
524 tristate "ARM AMBA PL022 SSP controller"
525 depends on ARM_AMBA
526 default y if MACH_U300
527 default y if ARCH_REALVIEW
528 default y if INTEGRATOR_IMPD1
529 default y if ARCH_VERSATILE
530 help
531 This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
532 controller. If you have an embedded system with an AMBA(R)
533 bus and a PL022 controller, say Y or M here.
534
535config SPI_PPC4xx
536 tristate "PPC4xx SPI Controller"
537 depends on PPC32 && 4xx
538 select SPI_BITBANG
539 help
540 This selects a driver for the PPC4xx SPI Controller.
541
542config SPI_PXA2XX
543 tristate "PXA2xx SSP SPI master"
544 depends on (ARCH_PXA || ARCH_MMP || PCI || ACPI)
545 select PXA_SSP if ARCH_PXA || ARCH_MMP
546 help
547 This enables using a PXA2xx or Sodaville SSP port as a SPI master
548 controller. The driver can be configured to use any SSP port and
549 additional documentation can be found a Documentation/spi/pxa2xx.rst.
550
551config SPI_PXA2XX_PCI
552 def_tristate SPI_PXA2XX && PCI && COMMON_CLK
553
554config SPI_ROCKCHIP
555 tristate "Rockchip SPI controller driver"
556 help
557 This selects a driver for Rockchip SPI controller.
558
559 If you say yes to this option, support will be included for
560 RK3066, RK3188 and RK3288 families of SPI controller.
561 Rockchip SPI controller support DMA transport and PIO mode.
562 The main usecase of this controller is to use spi flash as boot
563 device.
564
565config SPI_RB4XX
566 tristate "Mikrotik RB4XX SPI master"
567 depends on SPI_MASTER && ATH79
568 help
569 SPI controller driver for the Mikrotik RB4xx series boards.
570
571config SPI_RSPI
572 tristate "Renesas RSPI/QSPI controller"
573 depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
574 help
575 SPI driver for Renesas RSPI and QSPI blocks.
576
577config SPI_QCOM_QSPI
578 tristate "QTI QSPI controller"
579 depends on ARCH_QCOM
580 help
581 QSPI(Quad SPI) driver for Qualcomm QSPI controller.
582
583config SPI_QUP
584 tristate "Qualcomm SPI controller with QUP interface"
585 depends on ARCH_QCOM || (ARM && COMPILE_TEST)
586 help
587 Qualcomm Universal Peripheral (QUP) core is an AHB slave that
588 provides a common data path (an output FIFO and an input FIFO)
589 for serial peripheral interface (SPI) mini-core. SPI in master
590 mode supports up to 50MHz, up to four chip selects, programmable
591 data path from 4 bits to 32 bits and numerous protocol variants.
592
593 This driver can also be built as a module. If so, the module
594 will be called spi_qup.
595
596config SPI_QCOM_GENI
597 tristate "Qualcomm GENI based SPI controller"
598 depends on QCOM_GENI_SE
599 help
600 This driver supports GENI serial engine based SPI controller in
601 master mode on the Qualcomm Technologies Inc.'s SoCs. If you say
602 yes to this option, support will be included for the built-in SPI
603 interface on the Qualcomm Technologies Inc.'s SoCs.
604
605 This driver can also be built as a module. If so, the module
606 will be called spi-geni-qcom.
607
608config SPI_S3C24XX
609 tristate "Samsung S3C24XX series SPI"
610 depends on ARCH_S3C24XX
611 select SPI_BITBANG
612 help
613 SPI driver for Samsung S3C24XX series ARM SoCs
614
615config SPI_S3C24XX_FIQ
616 bool "S3C24XX driver with FIQ pseudo-DMA"
617 depends on SPI_S3C24XX
618 select FIQ
619 help
620 Enable FIQ support for the S3C24XX SPI driver to provide pseudo
621 DMA by using the fast-interrupt request framework, This allows
622 the driver to get DMA-like performance when there are either
623 no free DMA channels, or when doing transfers that required both
624 TX and RX data paths.
625
626config SPI_S3C64XX
627 tristate "Samsung S3C64XX series type SPI"
628 depends on (PLAT_SAMSUNG || ARCH_EXYNOS || COMPILE_TEST)
629 help
630 SPI driver for Samsung S3C64XX and newer SoCs.
631
632config SPI_SC18IS602
633 tristate "NXP SC18IS602/602B/603 I2C to SPI bridge"
634 depends on I2C
635 help
636 SPI driver for NXP SC18IS602/602B/603 I2C to SPI bridge.
637
638config SPI_SH_MSIOF
639 tristate "SuperH MSIOF SPI controller"
640 depends on HAVE_CLK
641 depends on ARCH_SHMOBILE || ARCH_RENESAS || COMPILE_TEST
642 help
643 SPI driver for SuperH and SH Mobile MSIOF blocks.
644
645config SPI_SH
646 tristate "SuperH SPI controller"
647 depends on SUPERH || COMPILE_TEST
648 help
649 SPI driver for SuperH SPI blocks.
650
651config SPI_SH_SCI
652 tristate "SuperH SCI SPI controller"
653 depends on SUPERH
654 select SPI_BITBANG
655 help
656 SPI driver for SuperH SCI blocks.
657
658config SPI_SH_HSPI
659 tristate "SuperH HSPI controller"
660 depends on ARCH_RENESAS || COMPILE_TEST
661 help
662 SPI driver for SuperH HSPI blocks.
663
664config SPI_SIFIVE
665 tristate "SiFive SPI controller"
666 depends on HAS_IOMEM
667 help
668 This exposes the SPI controller IP from SiFive.
669
670config SPI_SIRF
671 tristate "CSR SiRFprimaII SPI controller"
672 depends on SIRF_DMA
673 select SPI_BITBANG
674 help
675 SPI driver for CSR SiRFprimaII SoCs
676
677config SPI_SLAVE_MT27XX
678 tristate "MediaTek SPI slave device"
679 depends on ARCH_MEDIATEK || COMPILE_TEST
680 depends on SPI_SLAVE
681 help
682 This selects the MediaTek(R) SPI slave device driver.
683 If you want to use MediaTek(R) SPI slave interface,
684 say Y or M here.If you are not sure, say N.
685 SPI slave drivers for Mediatek MT27XX series ARM SoCs.
686
687config SPI_SPRD
688 tristate "Spreadtrum SPI controller"
689 depends on ARCH_SPRD || COMPILE_TEST
690 help
691 SPI driver for Spreadtrum SoCs.
692
693config SPI_SPRD_ADI
694 tristate "Spreadtrum ADI controller"
695 depends on ARCH_SPRD || COMPILE_TEST
696 depends on HWSPINLOCK || (COMPILE_TEST && !HWSPINLOCK)
697 help
698 ADI driver based on SPI for Spreadtrum SoCs.
699
700config SPI_STM32
701 tristate "STMicroelectronics STM32 SPI controller"
702 depends on ARCH_STM32 || COMPILE_TEST
703 help
704 SPI driver for STMicroelectronics STM32 SoCs.
705
706 STM32 SPI controller supports DMA and PIO modes. When DMA
707 is not available, the driver automatically falls back to
708 PIO mode.
709
710config SPI_STM32_QSPI
711 tristate "STMicroelectronics STM32 QUAD SPI controller"
712 depends on ARCH_STM32 || COMPILE_TEST
713 depends on OF
714 help
715 This enables support for the Quad SPI controller in master mode.
716 This driver does not support generic SPI. The implementation only
717 supports spi-mem interface.
718
719config SPI_ST_SSC4
720 tristate "STMicroelectronics SPI SSC-based driver"
721 depends on ARCH_STI || COMPILE_TEST
722 help
723 STMicroelectronics SoCs support for SPI. If you say yes to
724 this option, support will be included for the SSC driven SPI.
725
726config SPI_SUN4I
727 tristate "Allwinner A10 SoCs SPI controller"
728 depends on ARCH_SUNXI || COMPILE_TEST
729 help
730 SPI driver for Allwinner sun4i, sun5i and sun7i SoCs
731
732config SPI_SUN6I
733 tristate "Allwinner A31 SPI controller"
734 depends on ARCH_SUNXI || COMPILE_TEST
735 depends on RESET_CONTROLLER
736 help
737 This enables using the SPI controller on the Allwinner A31 SoCs.
738
739config SPI_SYNQUACER
740 tristate "Socionext's SynQuacer HighSpeed SPI controller"
741 depends on ARCH_SYNQUACER || COMPILE_TEST
742 help
743 SPI driver for Socionext's High speed SPI controller which provides
744 various operating modes for interfacing to serial peripheral devices
745 that use the de-facto standard SPI protocol.
746
747 It also supports the new dual-bit and quad-bit SPI protocol.
748
749config SPI_MXIC
750 tristate "Macronix MX25F0A SPI controller"
751 depends on SPI_MASTER
752 help
753 This selects the Macronix MX25F0A SPI controller driver.
754
755config SPI_MXS
756 tristate "Freescale MXS SPI controller"
757 depends on ARCH_MXS
758 select STMP_DEVICE
759 help
760 SPI driver for Freescale MXS devices.
761
762config SPI_TEGRA114
763 tristate "NVIDIA Tegra114 SPI Controller"
764 depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
765 depends on RESET_CONTROLLER
766 help
767 SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller
768 is different than the older SoCs SPI controller and also register interface
769 get changed with this controller.
770
771config SPI_TEGRA20_SFLASH
772 tristate "Nvidia Tegra20 Serial flash Controller"
773 depends on ARCH_TEGRA || COMPILE_TEST
774 depends on RESET_CONTROLLER
775 help
776 SPI driver for Nvidia Tegra20 Serial flash Controller interface.
777 The main usecase of this controller is to use spi flash as boot
778 device.
779
780config SPI_TEGRA20_SLINK
781 tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
782 depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
783 depends on RESET_CONTROLLER
784 help
785 SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
786
787config SPI_THUNDERX
788 tristate "Cavium ThunderX SPI controller"
789 depends on PCI && 64BIT && (ARM64 || COMPILE_TEST)
790 help
791 SPI host driver for the hardware found on Cavium ThunderX
792 SOCs.
793
794config SPI_TOPCLIFF_PCH
795 tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
796 depends on PCI && (X86_32 || MIPS || COMPILE_TEST)
797 help
798 SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
799 used in some x86 embedded processors.
800
801 This driver also supports the ML7213/ML7223/ML7831, a companion chip
802 for the Atom E6xx series and compatible with the Intel EG20T PCH.
803
804config SPI_TXX9
805 tristate "Toshiba TXx9 SPI controller"
806 depends on GPIOLIB && (CPU_TX49XX || COMPILE_TEST)
807 help
808 SPI driver for Toshiba TXx9 MIPS SoCs
809
810config SPI_UNIPHIER
811 tristate "Socionext UniPhier SPI Controller"
812 depends on (ARCH_UNIPHIER || COMPILE_TEST) && OF
813 help
814 This enables a driver for the Socionext UniPhier SoC SCSSI SPI controller.
815
816 UniPhier SoCs have SCSSI and MCSSI SPI controllers.
817 Every UniPhier SoC has SCSSI which supports single channel.
818 Older UniPhier Pro4/Pro5 also has MCSSI which support multiple channels.
819 This driver supports SCSSI only.
820
821 If your SoC supports SCSSI, say Y here.
822
823config SPI_XCOMM
824 tristate "Analog Devices AD-FMCOMMS1-EBZ SPI-I2C-bridge driver"
825 depends on I2C
826 help
827 Support for the SPI-I2C bridge found on the Analog Devices
828 AD-FMCOMMS1-EBZ board.
829
830config SPI_XILINX
831 tristate "Xilinx SPI controller common module"
832 depends on HAS_IOMEM
833 select SPI_BITBANG
834 help
835 This exposes the SPI controller IP from the Xilinx EDK.
836
837 See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
838 Product Specification document (DS464) for hardware details.
839
840 Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
841
842config SPI_XLP
843 tristate "Netlogic XLP SPI controller driver"
844 depends on CPU_XLP || ARCH_THUNDER2 || COMPILE_TEST
845 help
846 Enable support for the SPI controller on the Netlogic XLP SoCs.
847 Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX, XLP9XX
848 and XLP5XX.
849
850 If you have a Netlogic XLP platform say Y here.
851 If unsure, say N.
852
853config SPI_XTENSA_XTFPGA
854 tristate "Xtensa SPI controller for xtfpga"
855 depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST
856 select SPI_BITBANG
857 help
858 SPI driver for xtfpga SPI master controller.
859
860 This simple SPI master controller is built into xtfpga bitstreams
861 and is used to control daughterboard audio codec. It always transfers
862 16 bit words in SPI mode 0, automatically asserting CS on transfer
863 start and deasserting on end.
864
865config SPI_ZYNQ_QSPI
866 tristate "Xilinx Zynq QSPI controller"
867 depends on ARCH_ZYNQ || COMPILE_TEST
868 help
869 This enables support for the Zynq Quad SPI controller
870 in master mode.
871 This controller only supports SPI memory interface.
872
873config SPI_ZYNQMP_GQSPI
874 tristate "Xilinx ZynqMP GQSPI controller"
875 depends on (SPI_MASTER && HAS_DMA) || COMPILE_TEST
876 help
877 Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.
878
879#
880# Add new SPI master controllers in alphabetical order above this line
881#
882
883#
884# There are lots of SPI device types, with sensors and memory
885# being probably the most widely used ones.
886#
887comment "SPI Protocol Masters"
888
889config SPI_SPIDEV
890 tristate "User mode SPI device driver support"
891 help
892 This supports user mode SPI protocol drivers.
893
894 Note that this application programming interface is EXPERIMENTAL
895 and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
896
897config SPI_LOOPBACK_TEST
898 tristate "spi loopback test framework support"
899 depends on m
900 help
901 This enables the SPI loopback testing framework driver
902
903 primarily used for development of spi_master drivers
904 and to detect regressions
905
906config SPI_TLE62X0
907 tristate "Infineon TLE62X0 (for power switching)"
908 depends on SYSFS
909 help
910 SPI driver for Infineon TLE62X0 series line driver chips,
911 such as the TLE6220, TLE6230 and TLE6240. This provides a
912 sysfs interface, with each line presented as a kind of GPIO
913 exposing both switch control and diagnostic feedback.
914
915#
916# Add new SPI protocol masters in alphabetical order above this line
917#
918
919endif # SPI_MASTER
920
921#
922# SLAVE side ... listening to other SPI masters
923#
924
925config SPI_SLAVE
926 bool "SPI slave protocol handlers"
927 help
928 If your system has a slave-capable SPI controller, you can enable
929 slave protocol handlers.
930
931if SPI_SLAVE
932
933config SPI_SLAVE_TIME
934 tristate "SPI slave handler reporting boot up time"
935 help
936 SPI slave handler responding with the time of reception of the last
937 SPI message.
938
939config SPI_SLAVE_SYSTEM_CONTROL
940 tristate "SPI slave handler controlling system state"
941 help
942 SPI slave handler to allow remote control of system reboot, power
943 off, halt, and suspend.
944
945endif # SPI_SLAVE
946
947endif # SPI