Loading...
1/* Copyright (c) 2009-2011, Code Aurora Forum. All rights reserved.
2 *
3 * This program is free software; you can redistribute it and/or modify
4 * it under the terms of the GNU General Public License version 2 and
5 * only version 2 as published by the Free Software Foundation.
6 *
7 * This program is distributed in the hope that it will be useful,
8 * but WITHOUT ANY WARRANTY; without even the implied warranty of
9 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
10 * GNU General Public License for more details.
11 *
12 * You should have received a copy of the GNU General Public License
13 * along with this program; if not, write to the Free Software
14 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
15 * 02110-1301, USA.
16 *
17 */
18
19#include <linux/module.h>
20#include <linux/device.h>
21#include <linux/gpio/consumer.h>
22#include <linux/platform_device.h>
23#include <linux/clk.h>
24#include <linux/slab.h>
25#include <linux/interrupt.h>
26#include <linux/err.h>
27#include <linux/delay.h>
28#include <linux/io.h>
29#include <linux/ioport.h>
30#include <linux/uaccess.h>
31#include <linux/debugfs.h>
32#include <linux/seq_file.h>
33#include <linux/pm_runtime.h>
34#include <linux/of.h>
35#include <linux/of_device.h>
36#include <linux/reboot.h>
37#include <linux/reset.h>
38
39#include <linux/usb.h>
40#include <linux/usb/otg.h>
41#include <linux/usb/of.h>
42#include <linux/usb/ulpi.h>
43#include <linux/usb/gadget.h>
44#include <linux/usb/hcd.h>
45#include <linux/usb/msm_hsusb.h>
46#include <linux/usb/msm_hsusb_hw.h>
47#include <linux/regulator/consumer.h>
48
49#define MSM_USB_BASE (motg->regs)
50#define DRIVER_NAME "msm_otg"
51
52#define ULPI_IO_TIMEOUT_USEC (10 * 1000)
53#define LINK_RESET_TIMEOUT_USEC (250 * 1000)
54
55#define USB_PHY_3P3_VOL_MIN 3050000 /* uV */
56#define USB_PHY_3P3_VOL_MAX 3300000 /* uV */
57#define USB_PHY_3P3_HPM_LOAD 50000 /* uA */
58#define USB_PHY_3P3_LPM_LOAD 4000 /* uA */
59
60#define USB_PHY_1P8_VOL_MIN 1800000 /* uV */
61#define USB_PHY_1P8_VOL_MAX 1800000 /* uV */
62#define USB_PHY_1P8_HPM_LOAD 50000 /* uA */
63#define USB_PHY_1P8_LPM_LOAD 4000 /* uA */
64
65#define USB_PHY_VDD_DIG_VOL_MIN 1000000 /* uV */
66#define USB_PHY_VDD_DIG_VOL_MAX 1320000 /* uV */
67#define USB_PHY_SUSP_DIG_VOL 500000 /* uV */
68
69enum vdd_levels {
70 VDD_LEVEL_NONE = 0,
71 VDD_LEVEL_MIN,
72 VDD_LEVEL_MAX,
73};
74
75static int msm_hsusb_init_vddcx(struct msm_otg *motg, int init)
76{
77 int ret = 0;
78
79 if (init) {
80 ret = regulator_set_voltage(motg->vddcx,
81 motg->vdd_levels[VDD_LEVEL_MIN],
82 motg->vdd_levels[VDD_LEVEL_MAX]);
83 if (ret) {
84 dev_err(motg->phy.dev, "Cannot set vddcx voltage\n");
85 return ret;
86 }
87
88 ret = regulator_enable(motg->vddcx);
89 if (ret)
90 dev_err(motg->phy.dev, "unable to enable hsusb vddcx\n");
91 } else {
92 ret = regulator_set_voltage(motg->vddcx, 0,
93 motg->vdd_levels[VDD_LEVEL_MAX]);
94 if (ret)
95 dev_err(motg->phy.dev, "Cannot set vddcx voltage\n");
96 ret = regulator_disable(motg->vddcx);
97 if (ret)
98 dev_err(motg->phy.dev, "unable to disable hsusb vddcx\n");
99 }
100
101 return ret;
102}
103
104static int msm_hsusb_ldo_init(struct msm_otg *motg, int init)
105{
106 int rc = 0;
107
108 if (init) {
109 rc = regulator_set_voltage(motg->v3p3, USB_PHY_3P3_VOL_MIN,
110 USB_PHY_3P3_VOL_MAX);
111 if (rc) {
112 dev_err(motg->phy.dev, "Cannot set v3p3 voltage\n");
113 goto exit;
114 }
115 rc = regulator_enable(motg->v3p3);
116 if (rc) {
117 dev_err(motg->phy.dev, "unable to enable the hsusb 3p3\n");
118 goto exit;
119 }
120 rc = regulator_set_voltage(motg->v1p8, USB_PHY_1P8_VOL_MIN,
121 USB_PHY_1P8_VOL_MAX);
122 if (rc) {
123 dev_err(motg->phy.dev, "Cannot set v1p8 voltage\n");
124 goto disable_3p3;
125 }
126 rc = regulator_enable(motg->v1p8);
127 if (rc) {
128 dev_err(motg->phy.dev, "unable to enable the hsusb 1p8\n");
129 goto disable_3p3;
130 }
131
132 return 0;
133 }
134
135 regulator_disable(motg->v1p8);
136disable_3p3:
137 regulator_disable(motg->v3p3);
138exit:
139 return rc;
140}
141
142static int msm_hsusb_ldo_set_mode(struct msm_otg *motg, int on)
143{
144 int ret = 0;
145
146 if (on) {
147 ret = regulator_set_load(motg->v1p8, USB_PHY_1P8_HPM_LOAD);
148 if (ret < 0) {
149 pr_err("Could not set HPM for v1p8\n");
150 return ret;
151 }
152 ret = regulator_set_load(motg->v3p3, USB_PHY_3P3_HPM_LOAD);
153 if (ret < 0) {
154 pr_err("Could not set HPM for v3p3\n");
155 regulator_set_load(motg->v1p8, USB_PHY_1P8_LPM_LOAD);
156 return ret;
157 }
158 } else {
159 ret = regulator_set_load(motg->v1p8, USB_PHY_1P8_LPM_LOAD);
160 if (ret < 0)
161 pr_err("Could not set LPM for v1p8\n");
162 ret = regulator_set_load(motg->v3p3, USB_PHY_3P3_LPM_LOAD);
163 if (ret < 0)
164 pr_err("Could not set LPM for v3p3\n");
165 }
166
167 pr_debug("reg (%s)\n", on ? "HPM" : "LPM");
168 return ret < 0 ? ret : 0;
169}
170
171static int ulpi_read(struct usb_phy *phy, u32 reg)
172{
173 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
174 int cnt = 0;
175
176 /* initiate read operation */
177 writel(ULPI_RUN | ULPI_READ | ULPI_ADDR(reg),
178 USB_ULPI_VIEWPORT);
179
180 /* wait for completion */
181 while (cnt < ULPI_IO_TIMEOUT_USEC) {
182 if (!(readl(USB_ULPI_VIEWPORT) & ULPI_RUN))
183 break;
184 udelay(1);
185 cnt++;
186 }
187
188 if (cnt >= ULPI_IO_TIMEOUT_USEC) {
189 dev_err(phy->dev, "ulpi_read: timeout %08x\n",
190 readl(USB_ULPI_VIEWPORT));
191 return -ETIMEDOUT;
192 }
193 return ULPI_DATA_READ(readl(USB_ULPI_VIEWPORT));
194}
195
196static int ulpi_write(struct usb_phy *phy, u32 val, u32 reg)
197{
198 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
199 int cnt = 0;
200
201 /* initiate write operation */
202 writel(ULPI_RUN | ULPI_WRITE |
203 ULPI_ADDR(reg) | ULPI_DATA(val),
204 USB_ULPI_VIEWPORT);
205
206 /* wait for completion */
207 while (cnt < ULPI_IO_TIMEOUT_USEC) {
208 if (!(readl(USB_ULPI_VIEWPORT) & ULPI_RUN))
209 break;
210 udelay(1);
211 cnt++;
212 }
213
214 if (cnt >= ULPI_IO_TIMEOUT_USEC) {
215 dev_err(phy->dev, "ulpi_write: timeout\n");
216 return -ETIMEDOUT;
217 }
218 return 0;
219}
220
221static struct usb_phy_io_ops msm_otg_io_ops = {
222 .read = ulpi_read,
223 .write = ulpi_write,
224};
225
226static void ulpi_init(struct msm_otg *motg)
227{
228 struct msm_otg_platform_data *pdata = motg->pdata;
229 int *seq = pdata->phy_init_seq, idx;
230 u32 addr = ULPI_EXT_VENDOR_SPECIFIC;
231
232 for (idx = 0; idx < pdata->phy_init_sz; idx++) {
233 if (seq[idx] == -1)
234 continue;
235
236 dev_vdbg(motg->phy.dev, "ulpi: write 0x%02x to 0x%02x\n",
237 seq[idx], addr + idx);
238 ulpi_write(&motg->phy, seq[idx], addr + idx);
239 }
240}
241
242static int msm_phy_notify_disconnect(struct usb_phy *phy,
243 enum usb_device_speed speed)
244{
245 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
246 int val;
247
248 if (motg->manual_pullup) {
249 val = ULPI_MISC_A_VBUSVLDEXT | ULPI_MISC_A_VBUSVLDEXTSEL;
250 usb_phy_io_write(phy, val, ULPI_CLR(ULPI_MISC_A));
251 }
252
253 /*
254 * Put the transceiver in non-driving mode. Otherwise host
255 * may not detect soft-disconnection.
256 */
257 val = ulpi_read(phy, ULPI_FUNC_CTRL);
258 val &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
259 val |= ULPI_FUNC_CTRL_OPMODE_NONDRIVING;
260 ulpi_write(phy, val, ULPI_FUNC_CTRL);
261
262 return 0;
263}
264
265static int msm_otg_link_clk_reset(struct msm_otg *motg, bool assert)
266{
267 int ret;
268
269 if (assert)
270 ret = reset_control_assert(motg->link_rst);
271 else
272 ret = reset_control_deassert(motg->link_rst);
273
274 if (ret)
275 dev_err(motg->phy.dev, "usb link clk reset %s failed\n",
276 assert ? "assert" : "deassert");
277
278 return ret;
279}
280
281static int msm_otg_phy_clk_reset(struct msm_otg *motg)
282{
283 int ret = 0;
284
285 if (motg->phy_rst)
286 ret = reset_control_reset(motg->phy_rst);
287
288 if (ret)
289 dev_err(motg->phy.dev, "usb phy clk reset failed\n");
290
291 return ret;
292}
293
294static int msm_link_reset(struct msm_otg *motg)
295{
296 u32 val;
297 int ret;
298
299 ret = msm_otg_link_clk_reset(motg, 1);
300 if (ret)
301 return ret;
302
303 /* wait for 1ms delay as suggested in HPG. */
304 usleep_range(1000, 1200);
305
306 ret = msm_otg_link_clk_reset(motg, 0);
307 if (ret)
308 return ret;
309
310 if (motg->phy_number)
311 writel(readl(USB_PHY_CTRL2) | BIT(16), USB_PHY_CTRL2);
312
313 /* put transceiver in serial mode as part of reset */
314 val = readl(USB_PORTSC) & ~PORTSC_PTS_MASK;
315 writel(val | PORTSC_PTS_SERIAL, USB_PORTSC);
316
317 return 0;
318}
319
320static int msm_otg_reset(struct usb_phy *phy)
321{
322 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
323 int cnt = 0;
324
325 writel(USBCMD_RESET, USB_USBCMD);
326 while (cnt < LINK_RESET_TIMEOUT_USEC) {
327 if (!(readl(USB_USBCMD) & USBCMD_RESET))
328 break;
329 udelay(1);
330 cnt++;
331 }
332 if (cnt >= LINK_RESET_TIMEOUT_USEC)
333 return -ETIMEDOUT;
334
335 /* select ULPI phy and clear other status/control bits in PORTSC */
336 writel(PORTSC_PTS_ULPI, USB_PORTSC);
337
338 writel(0x0, USB_AHBBURST);
339 writel(0x08, USB_AHBMODE);
340
341 if (motg->phy_number)
342 writel(readl(USB_PHY_CTRL2) | BIT(16), USB_PHY_CTRL2);
343 return 0;
344}
345
346static void msm_phy_reset(struct msm_otg *motg)
347{
348 void __iomem *addr;
349
350 if (motg->pdata->phy_type != SNPS_28NM_INTEGRATED_PHY) {
351 msm_otg_phy_clk_reset(motg);
352 return;
353 }
354
355 addr = USB_PHY_CTRL;
356 if (motg->phy_number)
357 addr = USB_PHY_CTRL2;
358
359 /* Assert USB PHY_POR */
360 writel(readl(addr) | PHY_POR_ASSERT, addr);
361
362 /*
363 * wait for minimum 10 microseconds as suggested in HPG.
364 * Use a slightly larger value since the exact value didn't
365 * work 100% of the time.
366 */
367 udelay(12);
368
369 /* Deassert USB PHY_POR */
370 writel(readl(addr) & ~PHY_POR_ASSERT, addr);
371}
372
373static int msm_usb_reset(struct usb_phy *phy)
374{
375 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
376 int ret;
377
378 if (!IS_ERR(motg->core_clk))
379 clk_prepare_enable(motg->core_clk);
380
381 ret = msm_link_reset(motg);
382 if (ret) {
383 dev_err(phy->dev, "phy_reset failed\n");
384 return ret;
385 }
386
387 ret = msm_otg_reset(&motg->phy);
388 if (ret) {
389 dev_err(phy->dev, "link reset failed\n");
390 return ret;
391 }
392
393 msleep(100);
394
395 /* Reset USB PHY after performing USB Link RESET */
396 msm_phy_reset(motg);
397
398 if (!IS_ERR(motg->core_clk))
399 clk_disable_unprepare(motg->core_clk);
400
401 return 0;
402}
403
404static int msm_phy_init(struct usb_phy *phy)
405{
406 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
407 struct msm_otg_platform_data *pdata = motg->pdata;
408 u32 val, ulpi_val = 0;
409
410 /* Program USB PHY Override registers. */
411 ulpi_init(motg);
412
413 /*
414 * It is recommended in HPG to reset USB PHY after programming
415 * USB PHY Override registers.
416 */
417 msm_phy_reset(motg);
418
419 if (pdata->otg_control == OTG_PHY_CONTROL) {
420 val = readl(USB_OTGSC);
421 if (pdata->mode == USB_DR_MODE_OTG) {
422 ulpi_val = ULPI_INT_IDGRD | ULPI_INT_SESS_VALID;
423 val |= OTGSC_IDIE | OTGSC_BSVIE;
424 } else if (pdata->mode == USB_DR_MODE_PERIPHERAL) {
425 ulpi_val = ULPI_INT_SESS_VALID;
426 val |= OTGSC_BSVIE;
427 }
428 writel(val, USB_OTGSC);
429 ulpi_write(phy, ulpi_val, ULPI_USB_INT_EN_RISE);
430 ulpi_write(phy, ulpi_val, ULPI_USB_INT_EN_FALL);
431 }
432
433 if (motg->manual_pullup) {
434 val = ULPI_MISC_A_VBUSVLDEXTSEL | ULPI_MISC_A_VBUSVLDEXT;
435 ulpi_write(phy, val, ULPI_SET(ULPI_MISC_A));
436
437 val = readl(USB_GENCONFIG_2);
438 val |= GENCONFIG_2_SESS_VLD_CTRL_EN;
439 writel(val, USB_GENCONFIG_2);
440
441 val = readl(USB_USBCMD);
442 val |= USBCMD_SESS_VLD_CTRL;
443 writel(val, USB_USBCMD);
444
445 val = ulpi_read(phy, ULPI_FUNC_CTRL);
446 val &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
447 val |= ULPI_FUNC_CTRL_OPMODE_NORMAL;
448 ulpi_write(phy, val, ULPI_FUNC_CTRL);
449 }
450
451 if (motg->phy_number)
452 writel(readl(USB_PHY_CTRL2) | BIT(16), USB_PHY_CTRL2);
453
454 return 0;
455}
456
457#define PHY_SUSPEND_TIMEOUT_USEC (500 * 1000)
458#define PHY_RESUME_TIMEOUT_USEC (100 * 1000)
459
460#ifdef CONFIG_PM
461
462static int msm_hsusb_config_vddcx(struct msm_otg *motg, int high)
463{
464 int max_vol = motg->vdd_levels[VDD_LEVEL_MAX];
465 int min_vol;
466 int ret;
467
468 if (high)
469 min_vol = motg->vdd_levels[VDD_LEVEL_MIN];
470 else
471 min_vol = motg->vdd_levels[VDD_LEVEL_NONE];
472
473 ret = regulator_set_voltage(motg->vddcx, min_vol, max_vol);
474 if (ret) {
475 pr_err("Cannot set vddcx voltage\n");
476 return ret;
477 }
478
479 pr_debug("%s: min_vol:%d max_vol:%d\n", __func__, min_vol, max_vol);
480
481 return ret;
482}
483
484static int msm_otg_suspend(struct msm_otg *motg)
485{
486 struct usb_phy *phy = &motg->phy;
487 struct usb_bus *bus = phy->otg->host;
488 struct msm_otg_platform_data *pdata = motg->pdata;
489 void __iomem *addr;
490 int cnt = 0;
491
492 if (atomic_read(&motg->in_lpm))
493 return 0;
494
495 disable_irq(motg->irq);
496 /*
497 * Chipidea 45-nm PHY suspend sequence:
498 *
499 * Interrupt Latch Register auto-clear feature is not present
500 * in all PHY versions. Latch register is clear on read type.
501 * Clear latch register to avoid spurious wakeup from
502 * low power mode (LPM).
503 *
504 * PHY comparators are disabled when PHY enters into low power
505 * mode (LPM). Keep PHY comparators ON in LPM only when we expect
506 * VBUS/Id notifications from USB PHY. Otherwise turn off USB
507 * PHY comparators. This save significant amount of power.
508 *
509 * PLL is not turned off when PHY enters into low power mode (LPM).
510 * Disable PLL for maximum power savings.
511 */
512
513 if (motg->pdata->phy_type == CI_45NM_INTEGRATED_PHY) {
514 ulpi_read(phy, 0x14);
515 if (pdata->otg_control == OTG_PHY_CONTROL)
516 ulpi_write(phy, 0x01, 0x30);
517 ulpi_write(phy, 0x08, 0x09);
518 }
519
520 /*
521 * PHY may take some time or even fail to enter into low power
522 * mode (LPM). Hence poll for 500 msec and reset the PHY and link
523 * in failure case.
524 */
525 writel(readl(USB_PORTSC) | PORTSC_PHCD, USB_PORTSC);
526 while (cnt < PHY_SUSPEND_TIMEOUT_USEC) {
527 if (readl(USB_PORTSC) & PORTSC_PHCD)
528 break;
529 udelay(1);
530 cnt++;
531 }
532
533 if (cnt >= PHY_SUSPEND_TIMEOUT_USEC) {
534 dev_err(phy->dev, "Unable to suspend PHY\n");
535 msm_otg_reset(phy);
536 enable_irq(motg->irq);
537 return -ETIMEDOUT;
538 }
539
540 /*
541 * PHY has capability to generate interrupt asynchronously in low
542 * power mode (LPM). This interrupt is level triggered. So USB IRQ
543 * line must be disabled till async interrupt enable bit is cleared
544 * in USBCMD register. Assert STP (ULPI interface STOP signal) to
545 * block data communication from PHY.
546 */
547 writel(readl(USB_USBCMD) | ASYNC_INTR_CTRL | ULPI_STP_CTRL, USB_USBCMD);
548
549 addr = USB_PHY_CTRL;
550 if (motg->phy_number)
551 addr = USB_PHY_CTRL2;
552
553 if (motg->pdata->phy_type == SNPS_28NM_INTEGRATED_PHY &&
554 motg->pdata->otg_control == OTG_PMIC_CONTROL)
555 writel(readl(addr) | PHY_RETEN, addr);
556
557 clk_disable_unprepare(motg->pclk);
558 clk_disable_unprepare(motg->clk);
559 if (!IS_ERR(motg->core_clk))
560 clk_disable_unprepare(motg->core_clk);
561
562 if (motg->pdata->phy_type == SNPS_28NM_INTEGRATED_PHY &&
563 motg->pdata->otg_control == OTG_PMIC_CONTROL) {
564 msm_hsusb_ldo_set_mode(motg, 0);
565 msm_hsusb_config_vddcx(motg, 0);
566 }
567
568 if (device_may_wakeup(phy->dev))
569 enable_irq_wake(motg->irq);
570 if (bus)
571 clear_bit(HCD_FLAG_HW_ACCESSIBLE, &(bus_to_hcd(bus))->flags);
572
573 atomic_set(&motg->in_lpm, 1);
574 enable_irq(motg->irq);
575
576 dev_info(phy->dev, "USB in low power mode\n");
577
578 return 0;
579}
580
581static int msm_otg_resume(struct msm_otg *motg)
582{
583 struct usb_phy *phy = &motg->phy;
584 struct usb_bus *bus = phy->otg->host;
585 void __iomem *addr;
586 int cnt = 0;
587 unsigned temp;
588
589 if (!atomic_read(&motg->in_lpm))
590 return 0;
591
592 clk_prepare_enable(motg->pclk);
593 clk_prepare_enable(motg->clk);
594 if (!IS_ERR(motg->core_clk))
595 clk_prepare_enable(motg->core_clk);
596
597 if (motg->pdata->phy_type == SNPS_28NM_INTEGRATED_PHY &&
598 motg->pdata->otg_control == OTG_PMIC_CONTROL) {
599
600 addr = USB_PHY_CTRL;
601 if (motg->phy_number)
602 addr = USB_PHY_CTRL2;
603
604 msm_hsusb_ldo_set_mode(motg, 1);
605 msm_hsusb_config_vddcx(motg, 1);
606 writel(readl(addr) & ~PHY_RETEN, addr);
607 }
608
609 temp = readl(USB_USBCMD);
610 temp &= ~ASYNC_INTR_CTRL;
611 temp &= ~ULPI_STP_CTRL;
612 writel(temp, USB_USBCMD);
613
614 /*
615 * PHY comes out of low power mode (LPM) in case of wakeup
616 * from asynchronous interrupt.
617 */
618 if (!(readl(USB_PORTSC) & PORTSC_PHCD))
619 goto skip_phy_resume;
620
621 writel(readl(USB_PORTSC) & ~PORTSC_PHCD, USB_PORTSC);
622 while (cnt < PHY_RESUME_TIMEOUT_USEC) {
623 if (!(readl(USB_PORTSC) & PORTSC_PHCD))
624 break;
625 udelay(1);
626 cnt++;
627 }
628
629 if (cnt >= PHY_RESUME_TIMEOUT_USEC) {
630 /*
631 * This is a fatal error. Reset the link and
632 * PHY. USB state can not be restored. Re-insertion
633 * of USB cable is the only way to get USB working.
634 */
635 dev_err(phy->dev, "Unable to resume USB. Re-plugin the cable\n");
636 msm_otg_reset(phy);
637 }
638
639skip_phy_resume:
640 if (device_may_wakeup(phy->dev))
641 disable_irq_wake(motg->irq);
642 if (bus)
643 set_bit(HCD_FLAG_HW_ACCESSIBLE, &(bus_to_hcd(bus))->flags);
644
645 atomic_set(&motg->in_lpm, 0);
646
647 if (motg->async_int) {
648 motg->async_int = 0;
649 pm_runtime_put(phy->dev);
650 enable_irq(motg->irq);
651 }
652
653 dev_info(phy->dev, "USB exited from low power mode\n");
654
655 return 0;
656}
657#endif
658
659static void msm_otg_notify_charger(struct msm_otg *motg, unsigned mA)
660{
661 if (motg->cur_power == mA)
662 return;
663
664 /* TODO: Notify PMIC about available current */
665 dev_info(motg->phy.dev, "Avail curr from USB = %u\n", mA);
666 motg->cur_power = mA;
667}
668
669static int msm_otg_set_power(struct usb_phy *phy, unsigned mA)
670{
671 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
672
673 /*
674 * Gadget driver uses set_power method to notify about the
675 * available current based on suspend/configured states.
676 *
677 * IDEV_CHG can be drawn irrespective of suspend/un-configured
678 * states when CDP/ACA is connected.
679 */
680 if (motg->chg_type == USB_SDP_CHARGER)
681 msm_otg_notify_charger(motg, mA);
682
683 return 0;
684}
685
686static void msm_otg_start_host(struct usb_phy *phy, int on)
687{
688 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
689 struct msm_otg_platform_data *pdata = motg->pdata;
690 struct usb_hcd *hcd;
691
692 if (!phy->otg->host)
693 return;
694
695 hcd = bus_to_hcd(phy->otg->host);
696
697 if (on) {
698 dev_dbg(phy->dev, "host on\n");
699
700 if (pdata->vbus_power)
701 pdata->vbus_power(1);
702 /*
703 * Some boards have a switch cotrolled by gpio
704 * to enable/disable internal HUB. Enable internal
705 * HUB before kicking the host.
706 */
707 if (pdata->setup_gpio)
708 pdata->setup_gpio(OTG_STATE_A_HOST);
709#ifdef CONFIG_USB
710 usb_add_hcd(hcd, hcd->irq, IRQF_SHARED);
711 device_wakeup_enable(hcd->self.controller);
712#endif
713 } else {
714 dev_dbg(phy->dev, "host off\n");
715
716#ifdef CONFIG_USB
717 usb_remove_hcd(hcd);
718#endif
719 if (pdata->setup_gpio)
720 pdata->setup_gpio(OTG_STATE_UNDEFINED);
721 if (pdata->vbus_power)
722 pdata->vbus_power(0);
723 }
724}
725
726static int msm_otg_set_host(struct usb_otg *otg, struct usb_bus *host)
727{
728 struct msm_otg *motg = container_of(otg->usb_phy, struct msm_otg, phy);
729 struct usb_hcd *hcd;
730
731 /*
732 * Fail host registration if this board can support
733 * only peripheral configuration.
734 */
735 if (motg->pdata->mode == USB_DR_MODE_PERIPHERAL) {
736 dev_info(otg->usb_phy->dev, "Host mode is not supported\n");
737 return -ENODEV;
738 }
739
740 if (!host) {
741 if (otg->state == OTG_STATE_A_HOST) {
742 pm_runtime_get_sync(otg->usb_phy->dev);
743 msm_otg_start_host(otg->usb_phy, 0);
744 otg->host = NULL;
745 otg->state = OTG_STATE_UNDEFINED;
746 schedule_work(&motg->sm_work);
747 } else {
748 otg->host = NULL;
749 }
750
751 return 0;
752 }
753
754 hcd = bus_to_hcd(host);
755 hcd->power_budget = motg->pdata->power_budget;
756
757 otg->host = host;
758 dev_dbg(otg->usb_phy->dev, "host driver registered w/ tranceiver\n");
759
760 pm_runtime_get_sync(otg->usb_phy->dev);
761 schedule_work(&motg->sm_work);
762
763 return 0;
764}
765
766static void msm_otg_start_peripheral(struct usb_phy *phy, int on)
767{
768 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
769 struct msm_otg_platform_data *pdata = motg->pdata;
770
771 if (!phy->otg->gadget)
772 return;
773
774 if (on) {
775 dev_dbg(phy->dev, "gadget on\n");
776 /*
777 * Some boards have a switch cotrolled by gpio
778 * to enable/disable internal HUB. Disable internal
779 * HUB before kicking the gadget.
780 */
781 if (pdata->setup_gpio)
782 pdata->setup_gpio(OTG_STATE_B_PERIPHERAL);
783 usb_gadget_vbus_connect(phy->otg->gadget);
784 } else {
785 dev_dbg(phy->dev, "gadget off\n");
786 usb_gadget_vbus_disconnect(phy->otg->gadget);
787 if (pdata->setup_gpio)
788 pdata->setup_gpio(OTG_STATE_UNDEFINED);
789 }
790
791}
792
793static int msm_otg_set_peripheral(struct usb_otg *otg,
794 struct usb_gadget *gadget)
795{
796 struct msm_otg *motg = container_of(otg->usb_phy, struct msm_otg, phy);
797
798 /*
799 * Fail peripheral registration if this board can support
800 * only host configuration.
801 */
802 if (motg->pdata->mode == USB_DR_MODE_HOST) {
803 dev_info(otg->usb_phy->dev, "Peripheral mode is not supported\n");
804 return -ENODEV;
805 }
806
807 if (!gadget) {
808 if (otg->state == OTG_STATE_B_PERIPHERAL) {
809 pm_runtime_get_sync(otg->usb_phy->dev);
810 msm_otg_start_peripheral(otg->usb_phy, 0);
811 otg->gadget = NULL;
812 otg->state = OTG_STATE_UNDEFINED;
813 schedule_work(&motg->sm_work);
814 } else {
815 otg->gadget = NULL;
816 }
817
818 return 0;
819 }
820 otg->gadget = gadget;
821 dev_dbg(otg->usb_phy->dev,
822 "peripheral driver registered w/ tranceiver\n");
823
824 pm_runtime_get_sync(otg->usb_phy->dev);
825 schedule_work(&motg->sm_work);
826
827 return 0;
828}
829
830static bool msm_chg_check_secondary_det(struct msm_otg *motg)
831{
832 struct usb_phy *phy = &motg->phy;
833 u32 chg_det;
834 bool ret = false;
835
836 switch (motg->pdata->phy_type) {
837 case CI_45NM_INTEGRATED_PHY:
838 chg_det = ulpi_read(phy, 0x34);
839 ret = chg_det & (1 << 4);
840 break;
841 case SNPS_28NM_INTEGRATED_PHY:
842 chg_det = ulpi_read(phy, 0x87);
843 ret = chg_det & 1;
844 break;
845 default:
846 break;
847 }
848 return ret;
849}
850
851static void msm_chg_enable_secondary_det(struct msm_otg *motg)
852{
853 struct usb_phy *phy = &motg->phy;
854 u32 chg_det;
855
856 switch (motg->pdata->phy_type) {
857 case CI_45NM_INTEGRATED_PHY:
858 chg_det = ulpi_read(phy, 0x34);
859 /* Turn off charger block */
860 chg_det |= ~(1 << 1);
861 ulpi_write(phy, chg_det, 0x34);
862 udelay(20);
863 /* control chg block via ULPI */
864 chg_det &= ~(1 << 3);
865 ulpi_write(phy, chg_det, 0x34);
866 /* put it in host mode for enabling D- source */
867 chg_det &= ~(1 << 2);
868 ulpi_write(phy, chg_det, 0x34);
869 /* Turn on chg detect block */
870 chg_det &= ~(1 << 1);
871 ulpi_write(phy, chg_det, 0x34);
872 udelay(20);
873 /* enable chg detection */
874 chg_det &= ~(1 << 0);
875 ulpi_write(phy, chg_det, 0x34);
876 break;
877 case SNPS_28NM_INTEGRATED_PHY:
878 /*
879 * Configure DM as current source, DP as current sink
880 * and enable battery charging comparators.
881 */
882 ulpi_write(phy, 0x8, 0x85);
883 ulpi_write(phy, 0x2, 0x85);
884 ulpi_write(phy, 0x1, 0x85);
885 break;
886 default:
887 break;
888 }
889}
890
891static bool msm_chg_check_primary_det(struct msm_otg *motg)
892{
893 struct usb_phy *phy = &motg->phy;
894 u32 chg_det;
895 bool ret = false;
896
897 switch (motg->pdata->phy_type) {
898 case CI_45NM_INTEGRATED_PHY:
899 chg_det = ulpi_read(phy, 0x34);
900 ret = chg_det & (1 << 4);
901 break;
902 case SNPS_28NM_INTEGRATED_PHY:
903 chg_det = ulpi_read(phy, 0x87);
904 ret = chg_det & 1;
905 break;
906 default:
907 break;
908 }
909 return ret;
910}
911
912static void msm_chg_enable_primary_det(struct msm_otg *motg)
913{
914 struct usb_phy *phy = &motg->phy;
915 u32 chg_det;
916
917 switch (motg->pdata->phy_type) {
918 case CI_45NM_INTEGRATED_PHY:
919 chg_det = ulpi_read(phy, 0x34);
920 /* enable chg detection */
921 chg_det &= ~(1 << 0);
922 ulpi_write(phy, chg_det, 0x34);
923 break;
924 case SNPS_28NM_INTEGRATED_PHY:
925 /*
926 * Configure DP as current source, DM as current sink
927 * and enable battery charging comparators.
928 */
929 ulpi_write(phy, 0x2, 0x85);
930 ulpi_write(phy, 0x1, 0x85);
931 break;
932 default:
933 break;
934 }
935}
936
937static bool msm_chg_check_dcd(struct msm_otg *motg)
938{
939 struct usb_phy *phy = &motg->phy;
940 u32 line_state;
941 bool ret = false;
942
943 switch (motg->pdata->phy_type) {
944 case CI_45NM_INTEGRATED_PHY:
945 line_state = ulpi_read(phy, 0x15);
946 ret = !(line_state & 1);
947 break;
948 case SNPS_28NM_INTEGRATED_PHY:
949 line_state = ulpi_read(phy, 0x87);
950 ret = line_state & 2;
951 break;
952 default:
953 break;
954 }
955 return ret;
956}
957
958static void msm_chg_disable_dcd(struct msm_otg *motg)
959{
960 struct usb_phy *phy = &motg->phy;
961 u32 chg_det;
962
963 switch (motg->pdata->phy_type) {
964 case CI_45NM_INTEGRATED_PHY:
965 chg_det = ulpi_read(phy, 0x34);
966 chg_det &= ~(1 << 5);
967 ulpi_write(phy, chg_det, 0x34);
968 break;
969 case SNPS_28NM_INTEGRATED_PHY:
970 ulpi_write(phy, 0x10, 0x86);
971 break;
972 default:
973 break;
974 }
975}
976
977static void msm_chg_enable_dcd(struct msm_otg *motg)
978{
979 struct usb_phy *phy = &motg->phy;
980 u32 chg_det;
981
982 switch (motg->pdata->phy_type) {
983 case CI_45NM_INTEGRATED_PHY:
984 chg_det = ulpi_read(phy, 0x34);
985 /* Turn on D+ current source */
986 chg_det |= (1 << 5);
987 ulpi_write(phy, chg_det, 0x34);
988 break;
989 case SNPS_28NM_INTEGRATED_PHY:
990 /* Data contact detection enable */
991 ulpi_write(phy, 0x10, 0x85);
992 break;
993 default:
994 break;
995 }
996}
997
998static void msm_chg_block_on(struct msm_otg *motg)
999{
1000 struct usb_phy *phy = &motg->phy;
1001 u32 func_ctrl, chg_det;
1002
1003 /* put the controller in non-driving mode */
1004 func_ctrl = ulpi_read(phy, ULPI_FUNC_CTRL);
1005 func_ctrl &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
1006 func_ctrl |= ULPI_FUNC_CTRL_OPMODE_NONDRIVING;
1007 ulpi_write(phy, func_ctrl, ULPI_FUNC_CTRL);
1008
1009 switch (motg->pdata->phy_type) {
1010 case CI_45NM_INTEGRATED_PHY:
1011 chg_det = ulpi_read(phy, 0x34);
1012 /* control chg block via ULPI */
1013 chg_det &= ~(1 << 3);
1014 ulpi_write(phy, chg_det, 0x34);
1015 /* Turn on chg detect block */
1016 chg_det &= ~(1 << 1);
1017 ulpi_write(phy, chg_det, 0x34);
1018 udelay(20);
1019 break;
1020 case SNPS_28NM_INTEGRATED_PHY:
1021 /* Clear charger detecting control bits */
1022 ulpi_write(phy, 0x3F, 0x86);
1023 /* Clear alt interrupt latch and enable bits */
1024 ulpi_write(phy, 0x1F, 0x92);
1025 ulpi_write(phy, 0x1F, 0x95);
1026 udelay(100);
1027 break;
1028 default:
1029 break;
1030 }
1031}
1032
1033static void msm_chg_block_off(struct msm_otg *motg)
1034{
1035 struct usb_phy *phy = &motg->phy;
1036 u32 func_ctrl, chg_det;
1037
1038 switch (motg->pdata->phy_type) {
1039 case CI_45NM_INTEGRATED_PHY:
1040 chg_det = ulpi_read(phy, 0x34);
1041 /* Turn off charger block */
1042 chg_det |= ~(1 << 1);
1043 ulpi_write(phy, chg_det, 0x34);
1044 break;
1045 case SNPS_28NM_INTEGRATED_PHY:
1046 /* Clear charger detecting control bits */
1047 ulpi_write(phy, 0x3F, 0x86);
1048 /* Clear alt interrupt latch and enable bits */
1049 ulpi_write(phy, 0x1F, 0x92);
1050 ulpi_write(phy, 0x1F, 0x95);
1051 break;
1052 default:
1053 break;
1054 }
1055
1056 /* put the controller in normal mode */
1057 func_ctrl = ulpi_read(phy, ULPI_FUNC_CTRL);
1058 func_ctrl &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
1059 func_ctrl |= ULPI_FUNC_CTRL_OPMODE_NORMAL;
1060 ulpi_write(phy, func_ctrl, ULPI_FUNC_CTRL);
1061}
1062
1063#define MSM_CHG_DCD_POLL_TIME (100 * HZ/1000) /* 100 msec */
1064#define MSM_CHG_DCD_MAX_RETRIES 6 /* Tdcd_tmout = 6 * 100 msec */
1065#define MSM_CHG_PRIMARY_DET_TIME (40 * HZ/1000) /* TVDPSRC_ON */
1066#define MSM_CHG_SECONDARY_DET_TIME (40 * HZ/1000) /* TVDMSRC_ON */
1067static void msm_chg_detect_work(struct work_struct *w)
1068{
1069 struct msm_otg *motg = container_of(w, struct msm_otg, chg_work.work);
1070 struct usb_phy *phy = &motg->phy;
1071 bool is_dcd, tmout, vout;
1072 unsigned long delay;
1073
1074 dev_dbg(phy->dev, "chg detection work\n");
1075 switch (motg->chg_state) {
1076 case USB_CHG_STATE_UNDEFINED:
1077 pm_runtime_get_sync(phy->dev);
1078 msm_chg_block_on(motg);
1079 msm_chg_enable_dcd(motg);
1080 motg->chg_state = USB_CHG_STATE_WAIT_FOR_DCD;
1081 motg->dcd_retries = 0;
1082 delay = MSM_CHG_DCD_POLL_TIME;
1083 break;
1084 case USB_CHG_STATE_WAIT_FOR_DCD:
1085 is_dcd = msm_chg_check_dcd(motg);
1086 tmout = ++motg->dcd_retries == MSM_CHG_DCD_MAX_RETRIES;
1087 if (is_dcd || tmout) {
1088 msm_chg_disable_dcd(motg);
1089 msm_chg_enable_primary_det(motg);
1090 delay = MSM_CHG_PRIMARY_DET_TIME;
1091 motg->chg_state = USB_CHG_STATE_DCD_DONE;
1092 } else {
1093 delay = MSM_CHG_DCD_POLL_TIME;
1094 }
1095 break;
1096 case USB_CHG_STATE_DCD_DONE:
1097 vout = msm_chg_check_primary_det(motg);
1098 if (vout) {
1099 msm_chg_enable_secondary_det(motg);
1100 delay = MSM_CHG_SECONDARY_DET_TIME;
1101 motg->chg_state = USB_CHG_STATE_PRIMARY_DONE;
1102 } else {
1103 motg->chg_type = USB_SDP_CHARGER;
1104 motg->chg_state = USB_CHG_STATE_DETECTED;
1105 delay = 0;
1106 }
1107 break;
1108 case USB_CHG_STATE_PRIMARY_DONE:
1109 vout = msm_chg_check_secondary_det(motg);
1110 if (vout)
1111 motg->chg_type = USB_DCP_CHARGER;
1112 else
1113 motg->chg_type = USB_CDP_CHARGER;
1114 motg->chg_state = USB_CHG_STATE_SECONDARY_DONE;
1115 /* fall through */
1116 case USB_CHG_STATE_SECONDARY_DONE:
1117 motg->chg_state = USB_CHG_STATE_DETECTED;
1118 case USB_CHG_STATE_DETECTED:
1119 msm_chg_block_off(motg);
1120 dev_dbg(phy->dev, "charger = %d\n", motg->chg_type);
1121 schedule_work(&motg->sm_work);
1122 return;
1123 default:
1124 return;
1125 }
1126
1127 schedule_delayed_work(&motg->chg_work, delay);
1128}
1129
1130/*
1131 * We support OTG, Peripheral only and Host only configurations. In case
1132 * of OTG, mode switch (host-->peripheral/peripheral-->host) can happen
1133 * via Id pin status or user request (debugfs). Id/BSV interrupts are not
1134 * enabled when switch is controlled by user and default mode is supplied
1135 * by board file, which can be changed by userspace later.
1136 */
1137static void msm_otg_init_sm(struct msm_otg *motg)
1138{
1139 struct msm_otg_platform_data *pdata = motg->pdata;
1140 u32 otgsc = readl(USB_OTGSC);
1141
1142 switch (pdata->mode) {
1143 case USB_DR_MODE_OTG:
1144 if (pdata->otg_control == OTG_PHY_CONTROL) {
1145 if (otgsc & OTGSC_ID)
1146 set_bit(ID, &motg->inputs);
1147 else
1148 clear_bit(ID, &motg->inputs);
1149
1150 if (otgsc & OTGSC_BSV)
1151 set_bit(B_SESS_VLD, &motg->inputs);
1152 else
1153 clear_bit(B_SESS_VLD, &motg->inputs);
1154 } else if (pdata->otg_control == OTG_USER_CONTROL) {
1155 set_bit(ID, &motg->inputs);
1156 clear_bit(B_SESS_VLD, &motg->inputs);
1157 }
1158 break;
1159 case USB_DR_MODE_HOST:
1160 clear_bit(ID, &motg->inputs);
1161 break;
1162 case USB_DR_MODE_PERIPHERAL:
1163 set_bit(ID, &motg->inputs);
1164 if (otgsc & OTGSC_BSV)
1165 set_bit(B_SESS_VLD, &motg->inputs);
1166 else
1167 clear_bit(B_SESS_VLD, &motg->inputs);
1168 break;
1169 default:
1170 break;
1171 }
1172}
1173
1174static void msm_otg_sm_work(struct work_struct *w)
1175{
1176 struct msm_otg *motg = container_of(w, struct msm_otg, sm_work);
1177 struct usb_otg *otg = motg->phy.otg;
1178
1179 switch (otg->state) {
1180 case OTG_STATE_UNDEFINED:
1181 dev_dbg(otg->usb_phy->dev, "OTG_STATE_UNDEFINED state\n");
1182 msm_otg_reset(otg->usb_phy);
1183 msm_otg_init_sm(motg);
1184 otg->state = OTG_STATE_B_IDLE;
1185 /* FALL THROUGH */
1186 case OTG_STATE_B_IDLE:
1187 dev_dbg(otg->usb_phy->dev, "OTG_STATE_B_IDLE state\n");
1188 if (!test_bit(ID, &motg->inputs) && otg->host) {
1189 /* disable BSV bit */
1190 writel(readl(USB_OTGSC) & ~OTGSC_BSVIE, USB_OTGSC);
1191 msm_otg_start_host(otg->usb_phy, 1);
1192 otg->state = OTG_STATE_A_HOST;
1193 } else if (test_bit(B_SESS_VLD, &motg->inputs)) {
1194 switch (motg->chg_state) {
1195 case USB_CHG_STATE_UNDEFINED:
1196 msm_chg_detect_work(&motg->chg_work.work);
1197 break;
1198 case USB_CHG_STATE_DETECTED:
1199 switch (motg->chg_type) {
1200 case USB_DCP_CHARGER:
1201 msm_otg_notify_charger(motg,
1202 IDEV_CHG_MAX);
1203 break;
1204 case USB_CDP_CHARGER:
1205 msm_otg_notify_charger(motg,
1206 IDEV_CHG_MAX);
1207 msm_otg_start_peripheral(otg->usb_phy,
1208 1);
1209 otg->state
1210 = OTG_STATE_B_PERIPHERAL;
1211 break;
1212 case USB_SDP_CHARGER:
1213 msm_otg_notify_charger(motg, IUNIT);
1214 msm_otg_start_peripheral(otg->usb_phy,
1215 1);
1216 otg->state
1217 = OTG_STATE_B_PERIPHERAL;
1218 break;
1219 default:
1220 break;
1221 }
1222 break;
1223 default:
1224 break;
1225 }
1226 } else {
1227 /*
1228 * If charger detection work is pending, decrement
1229 * the pm usage counter to balance with the one that
1230 * is incremented in charger detection work.
1231 */
1232 if (cancel_delayed_work_sync(&motg->chg_work)) {
1233 pm_runtime_put_sync(otg->usb_phy->dev);
1234 msm_otg_reset(otg->usb_phy);
1235 }
1236 msm_otg_notify_charger(motg, 0);
1237 motg->chg_state = USB_CHG_STATE_UNDEFINED;
1238 motg->chg_type = USB_INVALID_CHARGER;
1239 }
1240
1241 if (otg->state == OTG_STATE_B_IDLE)
1242 pm_runtime_put_sync(otg->usb_phy->dev);
1243 break;
1244 case OTG_STATE_B_PERIPHERAL:
1245 dev_dbg(otg->usb_phy->dev, "OTG_STATE_B_PERIPHERAL state\n");
1246 if (!test_bit(B_SESS_VLD, &motg->inputs) ||
1247 !test_bit(ID, &motg->inputs)) {
1248 msm_otg_notify_charger(motg, 0);
1249 msm_otg_start_peripheral(otg->usb_phy, 0);
1250 motg->chg_state = USB_CHG_STATE_UNDEFINED;
1251 motg->chg_type = USB_INVALID_CHARGER;
1252 otg->state = OTG_STATE_B_IDLE;
1253 msm_otg_reset(otg->usb_phy);
1254 schedule_work(w);
1255 }
1256 break;
1257 case OTG_STATE_A_HOST:
1258 dev_dbg(otg->usb_phy->dev, "OTG_STATE_A_HOST state\n");
1259 if (test_bit(ID, &motg->inputs)) {
1260 msm_otg_start_host(otg->usb_phy, 0);
1261 otg->state = OTG_STATE_B_IDLE;
1262 msm_otg_reset(otg->usb_phy);
1263 schedule_work(w);
1264 }
1265 break;
1266 default:
1267 break;
1268 }
1269}
1270
1271static irqreturn_t msm_otg_irq(int irq, void *data)
1272{
1273 struct msm_otg *motg = data;
1274 struct usb_phy *phy = &motg->phy;
1275 u32 otgsc = 0;
1276
1277 if (atomic_read(&motg->in_lpm)) {
1278 disable_irq_nosync(irq);
1279 motg->async_int = 1;
1280 pm_runtime_get(phy->dev);
1281 return IRQ_HANDLED;
1282 }
1283
1284 otgsc = readl(USB_OTGSC);
1285 if (!(otgsc & (OTGSC_IDIS | OTGSC_BSVIS)))
1286 return IRQ_NONE;
1287
1288 if ((otgsc & OTGSC_IDIS) && (otgsc & OTGSC_IDIE)) {
1289 if (otgsc & OTGSC_ID)
1290 set_bit(ID, &motg->inputs);
1291 else
1292 clear_bit(ID, &motg->inputs);
1293 dev_dbg(phy->dev, "ID set/clear\n");
1294 pm_runtime_get_noresume(phy->dev);
1295 } else if ((otgsc & OTGSC_BSVIS) && (otgsc & OTGSC_BSVIE)) {
1296 if (otgsc & OTGSC_BSV)
1297 set_bit(B_SESS_VLD, &motg->inputs);
1298 else
1299 clear_bit(B_SESS_VLD, &motg->inputs);
1300 dev_dbg(phy->dev, "BSV set/clear\n");
1301 pm_runtime_get_noresume(phy->dev);
1302 }
1303
1304 writel(otgsc, USB_OTGSC);
1305 schedule_work(&motg->sm_work);
1306 return IRQ_HANDLED;
1307}
1308
1309static int msm_otg_mode_show(struct seq_file *s, void *unused)
1310{
1311 struct msm_otg *motg = s->private;
1312 struct usb_otg *otg = motg->phy.otg;
1313
1314 switch (otg->state) {
1315 case OTG_STATE_A_HOST:
1316 seq_puts(s, "host\n");
1317 break;
1318 case OTG_STATE_B_PERIPHERAL:
1319 seq_puts(s, "peripheral\n");
1320 break;
1321 default:
1322 seq_puts(s, "none\n");
1323 break;
1324 }
1325
1326 return 0;
1327}
1328
1329static int msm_otg_mode_open(struct inode *inode, struct file *file)
1330{
1331 return single_open(file, msm_otg_mode_show, inode->i_private);
1332}
1333
1334static ssize_t msm_otg_mode_write(struct file *file, const char __user *ubuf,
1335 size_t count, loff_t *ppos)
1336{
1337 struct seq_file *s = file->private_data;
1338 struct msm_otg *motg = s->private;
1339 char buf[16];
1340 struct usb_otg *otg = motg->phy.otg;
1341 int status = count;
1342 enum usb_dr_mode req_mode;
1343
1344 memset(buf, 0x00, sizeof(buf));
1345
1346 if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count))) {
1347 status = -EFAULT;
1348 goto out;
1349 }
1350
1351 if (!strncmp(buf, "host", 4)) {
1352 req_mode = USB_DR_MODE_HOST;
1353 } else if (!strncmp(buf, "peripheral", 10)) {
1354 req_mode = USB_DR_MODE_PERIPHERAL;
1355 } else if (!strncmp(buf, "none", 4)) {
1356 req_mode = USB_DR_MODE_UNKNOWN;
1357 } else {
1358 status = -EINVAL;
1359 goto out;
1360 }
1361
1362 switch (req_mode) {
1363 case USB_DR_MODE_UNKNOWN:
1364 switch (otg->state) {
1365 case OTG_STATE_A_HOST:
1366 case OTG_STATE_B_PERIPHERAL:
1367 set_bit(ID, &motg->inputs);
1368 clear_bit(B_SESS_VLD, &motg->inputs);
1369 break;
1370 default:
1371 goto out;
1372 }
1373 break;
1374 case USB_DR_MODE_PERIPHERAL:
1375 switch (otg->state) {
1376 case OTG_STATE_B_IDLE:
1377 case OTG_STATE_A_HOST:
1378 set_bit(ID, &motg->inputs);
1379 set_bit(B_SESS_VLD, &motg->inputs);
1380 break;
1381 default:
1382 goto out;
1383 }
1384 break;
1385 case USB_DR_MODE_HOST:
1386 switch (otg->state) {
1387 case OTG_STATE_B_IDLE:
1388 case OTG_STATE_B_PERIPHERAL:
1389 clear_bit(ID, &motg->inputs);
1390 break;
1391 default:
1392 goto out;
1393 }
1394 break;
1395 default:
1396 goto out;
1397 }
1398
1399 pm_runtime_get_sync(otg->usb_phy->dev);
1400 schedule_work(&motg->sm_work);
1401out:
1402 return status;
1403}
1404
1405static const struct file_operations msm_otg_mode_fops = {
1406 .open = msm_otg_mode_open,
1407 .read = seq_read,
1408 .write = msm_otg_mode_write,
1409 .llseek = seq_lseek,
1410 .release = single_release,
1411};
1412
1413static struct dentry *msm_otg_dbg_root;
1414static struct dentry *msm_otg_dbg_mode;
1415
1416static int msm_otg_debugfs_init(struct msm_otg *motg)
1417{
1418 msm_otg_dbg_root = debugfs_create_dir("msm_otg", NULL);
1419
1420 if (!msm_otg_dbg_root || IS_ERR(msm_otg_dbg_root))
1421 return -ENODEV;
1422
1423 msm_otg_dbg_mode = debugfs_create_file("mode", S_IRUGO | S_IWUSR,
1424 msm_otg_dbg_root, motg, &msm_otg_mode_fops);
1425 if (!msm_otg_dbg_mode) {
1426 debugfs_remove(msm_otg_dbg_root);
1427 msm_otg_dbg_root = NULL;
1428 return -ENODEV;
1429 }
1430
1431 return 0;
1432}
1433
1434static void msm_otg_debugfs_cleanup(void)
1435{
1436 debugfs_remove(msm_otg_dbg_mode);
1437 debugfs_remove(msm_otg_dbg_root);
1438}
1439
1440static const struct of_device_id msm_otg_dt_match[] = {
1441 {
1442 .compatible = "qcom,usb-otg-ci",
1443 .data = (void *) CI_45NM_INTEGRATED_PHY
1444 },
1445 {
1446 .compatible = "qcom,usb-otg-snps",
1447 .data = (void *) SNPS_28NM_INTEGRATED_PHY
1448 },
1449 { }
1450};
1451MODULE_DEVICE_TABLE(of, msm_otg_dt_match);
1452
1453static int msm_otg_vbus_notifier(struct notifier_block *nb, unsigned long event,
1454 void *ptr)
1455{
1456 struct msm_usb_cable *vbus = container_of(nb, struct msm_usb_cable, nb);
1457 struct msm_otg *motg = container_of(vbus, struct msm_otg, vbus);
1458
1459 if (event)
1460 set_bit(B_SESS_VLD, &motg->inputs);
1461 else
1462 clear_bit(B_SESS_VLD, &motg->inputs);
1463
1464 if (test_bit(B_SESS_VLD, &motg->inputs)) {
1465 /* Switch D+/D- lines to Device connector */
1466 gpiod_set_value_cansleep(motg->switch_gpio, 0);
1467 } else {
1468 /* Switch D+/D- lines to Hub */
1469 gpiod_set_value_cansleep(motg->switch_gpio, 1);
1470 }
1471
1472 schedule_work(&motg->sm_work);
1473
1474 return NOTIFY_DONE;
1475}
1476
1477static int msm_otg_id_notifier(struct notifier_block *nb, unsigned long event,
1478 void *ptr)
1479{
1480 struct msm_usb_cable *id = container_of(nb, struct msm_usb_cable, nb);
1481 struct msm_otg *motg = container_of(id, struct msm_otg, id);
1482
1483 if (event)
1484 clear_bit(ID, &motg->inputs);
1485 else
1486 set_bit(ID, &motg->inputs);
1487
1488 schedule_work(&motg->sm_work);
1489
1490 return NOTIFY_DONE;
1491}
1492
1493static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg)
1494{
1495 struct msm_otg_platform_data *pdata;
1496 struct extcon_dev *ext_id, *ext_vbus;
1497 struct device_node *node = pdev->dev.of_node;
1498 struct property *prop;
1499 int len, ret, words;
1500 u32 val, tmp[3];
1501
1502 pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
1503 if (!pdata)
1504 return -ENOMEM;
1505
1506 motg->pdata = pdata;
1507
1508 pdata->phy_type = (enum msm_usb_phy_type)of_device_get_match_data(&pdev->dev);
1509 if (!pdata->phy_type)
1510 return 1;
1511
1512 motg->link_rst = devm_reset_control_get(&pdev->dev, "link");
1513 if (IS_ERR(motg->link_rst))
1514 return PTR_ERR(motg->link_rst);
1515
1516 motg->phy_rst = devm_reset_control_get(&pdev->dev, "phy");
1517 if (IS_ERR(motg->phy_rst))
1518 motg->phy_rst = NULL;
1519
1520 pdata->mode = usb_get_dr_mode(&pdev->dev);
1521 if (pdata->mode == USB_DR_MODE_UNKNOWN)
1522 pdata->mode = USB_DR_MODE_OTG;
1523
1524 pdata->otg_control = OTG_PHY_CONTROL;
1525 if (!of_property_read_u32(node, "qcom,otg-control", &val))
1526 if (val == OTG_PMIC_CONTROL)
1527 pdata->otg_control = val;
1528
1529 if (!of_property_read_u32(node, "qcom,phy-num", &val) && val < 2)
1530 motg->phy_number = val;
1531
1532 motg->vdd_levels[VDD_LEVEL_NONE] = USB_PHY_SUSP_DIG_VOL;
1533 motg->vdd_levels[VDD_LEVEL_MIN] = USB_PHY_VDD_DIG_VOL_MIN;
1534 motg->vdd_levels[VDD_LEVEL_MAX] = USB_PHY_VDD_DIG_VOL_MAX;
1535
1536 if (of_get_property(node, "qcom,vdd-levels", &len) &&
1537 len == sizeof(tmp)) {
1538 of_property_read_u32_array(node, "qcom,vdd-levels",
1539 tmp, len / sizeof(*tmp));
1540 motg->vdd_levels[VDD_LEVEL_NONE] = tmp[VDD_LEVEL_NONE];
1541 motg->vdd_levels[VDD_LEVEL_MIN] = tmp[VDD_LEVEL_MIN];
1542 motg->vdd_levels[VDD_LEVEL_MAX] = tmp[VDD_LEVEL_MAX];
1543 }
1544
1545 motg->manual_pullup = of_property_read_bool(node, "qcom,manual-pullup");
1546
1547 motg->switch_gpio = devm_gpiod_get_optional(&pdev->dev, "switch",
1548 GPIOD_OUT_LOW);
1549 if (IS_ERR(motg->switch_gpio))
1550 return PTR_ERR(motg->switch_gpio);
1551
1552 ext_id = ERR_PTR(-ENODEV);
1553 ext_vbus = ERR_PTR(-ENODEV);
1554 if (of_property_read_bool(node, "extcon")) {
1555
1556 /* Each one of them is not mandatory */
1557 ext_vbus = extcon_get_edev_by_phandle(&pdev->dev, 0);
1558 if (IS_ERR(ext_vbus) && PTR_ERR(ext_vbus) != -ENODEV)
1559 return PTR_ERR(ext_vbus);
1560
1561 ext_id = extcon_get_edev_by_phandle(&pdev->dev, 1);
1562 if (IS_ERR(ext_id) && PTR_ERR(ext_id) != -ENODEV)
1563 return PTR_ERR(ext_id);
1564 }
1565
1566 if (!IS_ERR(ext_vbus)) {
1567 motg->vbus.extcon = ext_vbus;
1568 motg->vbus.nb.notifier_call = msm_otg_vbus_notifier;
1569 ret = extcon_register_notifier(ext_vbus, EXTCON_USB,
1570 &motg->vbus.nb);
1571 if (ret < 0) {
1572 dev_err(&pdev->dev, "register VBUS notifier failed\n");
1573 return ret;
1574 }
1575
1576 ret = extcon_get_cable_state_(ext_vbus, EXTCON_USB);
1577 if (ret)
1578 set_bit(B_SESS_VLD, &motg->inputs);
1579 else
1580 clear_bit(B_SESS_VLD, &motg->inputs);
1581 }
1582
1583 if (!IS_ERR(ext_id)) {
1584 motg->id.extcon = ext_id;
1585 motg->id.nb.notifier_call = msm_otg_id_notifier;
1586 ret = extcon_register_notifier(ext_id, EXTCON_USB_HOST,
1587 &motg->id.nb);
1588 if (ret < 0) {
1589 dev_err(&pdev->dev, "register ID notifier failed\n");
1590 extcon_unregister_notifier(motg->vbus.extcon,
1591 EXTCON_USB, &motg->vbus.nb);
1592 return ret;
1593 }
1594
1595 ret = extcon_get_cable_state_(ext_id, EXTCON_USB_HOST);
1596 if (ret)
1597 clear_bit(ID, &motg->inputs);
1598 else
1599 set_bit(ID, &motg->inputs);
1600 }
1601
1602 prop = of_find_property(node, "qcom,phy-init-sequence", &len);
1603 if (!prop || !len)
1604 return 0;
1605
1606 words = len / sizeof(u32);
1607
1608 if (words >= ULPI_EXT_VENDOR_SPECIFIC) {
1609 dev_warn(&pdev->dev, "Too big PHY init sequence %d\n", words);
1610 return 0;
1611 }
1612
1613 pdata->phy_init_seq = devm_kzalloc(&pdev->dev, len, GFP_KERNEL);
1614 if (!pdata->phy_init_seq)
1615 return 0;
1616
1617 ret = of_property_read_u32_array(node, "qcom,phy-init-sequence",
1618 pdata->phy_init_seq, words);
1619 if (!ret)
1620 pdata->phy_init_sz = words;
1621
1622 return 0;
1623}
1624
1625static int msm_otg_reboot_notify(struct notifier_block *this,
1626 unsigned long code, void *unused)
1627{
1628 struct msm_otg *motg = container_of(this, struct msm_otg, reboot);
1629
1630 /*
1631 * Ensure that D+/D- lines are routed to uB connector, so
1632 * we could load bootloader/kernel at next reboot
1633 */
1634 gpiod_set_value_cansleep(motg->switch_gpio, 0);
1635 return NOTIFY_DONE;
1636}
1637
1638static int msm_otg_probe(struct platform_device *pdev)
1639{
1640 struct regulator_bulk_data regs[3];
1641 int ret = 0;
1642 struct device_node *np = pdev->dev.of_node;
1643 struct msm_otg_platform_data *pdata;
1644 struct resource *res;
1645 struct msm_otg *motg;
1646 struct usb_phy *phy;
1647 void __iomem *phy_select;
1648
1649 motg = devm_kzalloc(&pdev->dev, sizeof(struct msm_otg), GFP_KERNEL);
1650 if (!motg)
1651 return -ENOMEM;
1652
1653 motg->phy.otg = devm_kzalloc(&pdev->dev, sizeof(struct usb_otg),
1654 GFP_KERNEL);
1655 if (!motg->phy.otg)
1656 return -ENOMEM;
1657
1658 phy = &motg->phy;
1659 phy->dev = &pdev->dev;
1660
1661 motg->clk = devm_clk_get(&pdev->dev, np ? "core" : "usb_hs_clk");
1662 if (IS_ERR(motg->clk)) {
1663 dev_err(&pdev->dev, "failed to get usb_hs_clk\n");
1664 return PTR_ERR(motg->clk);
1665 }
1666
1667 /*
1668 * If USB Core is running its protocol engine based on CORE CLK,
1669 * CORE CLK must be running at >55Mhz for correct HSUSB
1670 * operation and USB core cannot tolerate frequency changes on
1671 * CORE CLK.
1672 */
1673 motg->pclk = devm_clk_get(&pdev->dev, np ? "iface" : "usb_hs_pclk");
1674 if (IS_ERR(motg->pclk)) {
1675 dev_err(&pdev->dev, "failed to get usb_hs_pclk\n");
1676 return PTR_ERR(motg->pclk);
1677 }
1678
1679 /*
1680 * USB core clock is not present on all MSM chips. This
1681 * clock is introduced to remove the dependency on AXI
1682 * bus frequency.
1683 */
1684 motg->core_clk = devm_clk_get(&pdev->dev,
1685 np ? "alt_core" : "usb_hs_core_clk");
1686
1687 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1688 if (!res)
1689 return -EINVAL;
1690 motg->regs = devm_ioremap(&pdev->dev, res->start, resource_size(res));
1691 if (!motg->regs)
1692 return -ENOMEM;
1693
1694 pdata = dev_get_platdata(&pdev->dev);
1695 if (!pdata) {
1696 if (!np)
1697 return -ENXIO;
1698 ret = msm_otg_read_dt(pdev, motg);
1699 if (ret)
1700 return ret;
1701 }
1702
1703 /*
1704 * NOTE: The PHYs can be multiplexed between the chipidea controller
1705 * and the dwc3 controller, using a single bit. It is important that
1706 * the dwc3 driver does not set this bit in an incompatible way.
1707 */
1708 if (motg->phy_number) {
1709 phy_select = devm_ioremap_nocache(&pdev->dev, USB2_PHY_SEL, 4);
1710 if (!phy_select) {
1711 ret = -ENOMEM;
1712 goto unregister_extcon;
1713 }
1714 /* Enable second PHY with the OTG port */
1715 writel(0x1, phy_select);
1716 }
1717
1718 dev_info(&pdev->dev, "OTG regs = %p\n", motg->regs);
1719
1720 motg->irq = platform_get_irq(pdev, 0);
1721 if (motg->irq < 0) {
1722 dev_err(&pdev->dev, "platform_get_irq failed\n");
1723 ret = motg->irq;
1724 goto unregister_extcon;
1725 }
1726
1727 regs[0].supply = "vddcx";
1728 regs[1].supply = "v3p3";
1729 regs[2].supply = "v1p8";
1730
1731 ret = devm_regulator_bulk_get(motg->phy.dev, ARRAY_SIZE(regs), regs);
1732 if (ret)
1733 goto unregister_extcon;
1734
1735 motg->vddcx = regs[0].consumer;
1736 motg->v3p3 = regs[1].consumer;
1737 motg->v1p8 = regs[2].consumer;
1738
1739 clk_set_rate(motg->clk, 60000000);
1740
1741 clk_prepare_enable(motg->clk);
1742 clk_prepare_enable(motg->pclk);
1743
1744 if (!IS_ERR(motg->core_clk))
1745 clk_prepare_enable(motg->core_clk);
1746
1747 ret = msm_hsusb_init_vddcx(motg, 1);
1748 if (ret) {
1749 dev_err(&pdev->dev, "hsusb vddcx configuration failed\n");
1750 goto disable_clks;
1751 }
1752
1753 ret = msm_hsusb_ldo_init(motg, 1);
1754 if (ret) {
1755 dev_err(&pdev->dev, "hsusb vreg configuration failed\n");
1756 goto disable_vddcx;
1757 }
1758 ret = msm_hsusb_ldo_set_mode(motg, 1);
1759 if (ret) {
1760 dev_err(&pdev->dev, "hsusb vreg enable failed\n");
1761 goto disable_ldo;
1762 }
1763
1764 writel(0, USB_USBINTR);
1765 writel(0, USB_OTGSC);
1766
1767 INIT_WORK(&motg->sm_work, msm_otg_sm_work);
1768 INIT_DELAYED_WORK(&motg->chg_work, msm_chg_detect_work);
1769 ret = devm_request_irq(&pdev->dev, motg->irq, msm_otg_irq, IRQF_SHARED,
1770 "msm_otg", motg);
1771 if (ret) {
1772 dev_err(&pdev->dev, "request irq failed\n");
1773 goto disable_ldo;
1774 }
1775
1776 phy->init = msm_phy_init;
1777 phy->set_power = msm_otg_set_power;
1778 phy->notify_disconnect = msm_phy_notify_disconnect;
1779 phy->type = USB_PHY_TYPE_USB2;
1780
1781 phy->io_ops = &msm_otg_io_ops;
1782
1783 phy->otg->usb_phy = &motg->phy;
1784 phy->otg->set_host = msm_otg_set_host;
1785 phy->otg->set_peripheral = msm_otg_set_peripheral;
1786
1787 msm_usb_reset(phy);
1788
1789 ret = usb_add_phy_dev(&motg->phy);
1790 if (ret) {
1791 dev_err(&pdev->dev, "usb_add_phy failed\n");
1792 goto disable_ldo;
1793 }
1794
1795 platform_set_drvdata(pdev, motg);
1796 device_init_wakeup(&pdev->dev, 1);
1797
1798 if (motg->pdata->mode == USB_DR_MODE_OTG &&
1799 motg->pdata->otg_control == OTG_USER_CONTROL) {
1800 ret = msm_otg_debugfs_init(motg);
1801 if (ret)
1802 dev_dbg(&pdev->dev, "Can not create mode change file\n");
1803 }
1804
1805 if (test_bit(B_SESS_VLD, &motg->inputs)) {
1806 /* Switch D+/D- lines to Device connector */
1807 gpiod_set_value_cansleep(motg->switch_gpio, 0);
1808 } else {
1809 /* Switch D+/D- lines to Hub */
1810 gpiod_set_value_cansleep(motg->switch_gpio, 1);
1811 }
1812
1813 motg->reboot.notifier_call = msm_otg_reboot_notify;
1814 register_reboot_notifier(&motg->reboot);
1815
1816 pm_runtime_set_active(&pdev->dev);
1817 pm_runtime_enable(&pdev->dev);
1818
1819 return 0;
1820
1821disable_ldo:
1822 msm_hsusb_ldo_init(motg, 0);
1823disable_vddcx:
1824 msm_hsusb_init_vddcx(motg, 0);
1825disable_clks:
1826 clk_disable_unprepare(motg->pclk);
1827 clk_disable_unprepare(motg->clk);
1828 if (!IS_ERR(motg->core_clk))
1829 clk_disable_unprepare(motg->core_clk);
1830unregister_extcon:
1831 extcon_unregister_notifier(motg->id.extcon,
1832 EXTCON_USB_HOST, &motg->id.nb);
1833 extcon_unregister_notifier(motg->vbus.extcon,
1834 EXTCON_USB, &motg->vbus.nb);
1835
1836 return ret;
1837}
1838
1839static int msm_otg_remove(struct platform_device *pdev)
1840{
1841 struct msm_otg *motg = platform_get_drvdata(pdev);
1842 struct usb_phy *phy = &motg->phy;
1843 int cnt = 0;
1844
1845 if (phy->otg->host || phy->otg->gadget)
1846 return -EBUSY;
1847
1848 unregister_reboot_notifier(&motg->reboot);
1849
1850 /*
1851 * Ensure that D+/D- lines are routed to uB connector, so
1852 * we could load bootloader/kernel at next reboot
1853 */
1854 gpiod_set_value_cansleep(motg->switch_gpio, 0);
1855
1856 extcon_unregister_notifier(motg->id.extcon, EXTCON_USB_HOST, &motg->id.nb);
1857 extcon_unregister_notifier(motg->vbus.extcon, EXTCON_USB, &motg->vbus.nb);
1858
1859 msm_otg_debugfs_cleanup();
1860 cancel_delayed_work_sync(&motg->chg_work);
1861 cancel_work_sync(&motg->sm_work);
1862
1863 pm_runtime_resume(&pdev->dev);
1864
1865 device_init_wakeup(&pdev->dev, 0);
1866 pm_runtime_disable(&pdev->dev);
1867
1868 usb_remove_phy(phy);
1869 disable_irq(motg->irq);
1870
1871 /*
1872 * Put PHY in low power mode.
1873 */
1874 ulpi_read(phy, 0x14);
1875 ulpi_write(phy, 0x08, 0x09);
1876
1877 writel(readl(USB_PORTSC) | PORTSC_PHCD, USB_PORTSC);
1878 while (cnt < PHY_SUSPEND_TIMEOUT_USEC) {
1879 if (readl(USB_PORTSC) & PORTSC_PHCD)
1880 break;
1881 udelay(1);
1882 cnt++;
1883 }
1884 if (cnt >= PHY_SUSPEND_TIMEOUT_USEC)
1885 dev_err(phy->dev, "Unable to suspend PHY\n");
1886
1887 clk_disable_unprepare(motg->pclk);
1888 clk_disable_unprepare(motg->clk);
1889 if (!IS_ERR(motg->core_clk))
1890 clk_disable_unprepare(motg->core_clk);
1891 msm_hsusb_ldo_init(motg, 0);
1892
1893 pm_runtime_set_suspended(&pdev->dev);
1894
1895 return 0;
1896}
1897
1898#ifdef CONFIG_PM
1899static int msm_otg_runtime_idle(struct device *dev)
1900{
1901 struct msm_otg *motg = dev_get_drvdata(dev);
1902 struct usb_otg *otg = motg->phy.otg;
1903
1904 dev_dbg(dev, "OTG runtime idle\n");
1905
1906 /*
1907 * It is observed some times that a spurious interrupt
1908 * comes when PHY is put into LPM immediately after PHY reset.
1909 * This 1 sec delay also prevents entering into LPM immediately
1910 * after asynchronous interrupt.
1911 */
1912 if (otg->state != OTG_STATE_UNDEFINED)
1913 pm_schedule_suspend(dev, 1000);
1914
1915 return -EAGAIN;
1916}
1917
1918static int msm_otg_runtime_suspend(struct device *dev)
1919{
1920 struct msm_otg *motg = dev_get_drvdata(dev);
1921
1922 dev_dbg(dev, "OTG runtime suspend\n");
1923 return msm_otg_suspend(motg);
1924}
1925
1926static int msm_otg_runtime_resume(struct device *dev)
1927{
1928 struct msm_otg *motg = dev_get_drvdata(dev);
1929
1930 dev_dbg(dev, "OTG runtime resume\n");
1931 return msm_otg_resume(motg);
1932}
1933#endif
1934
1935#ifdef CONFIG_PM_SLEEP
1936static int msm_otg_pm_suspend(struct device *dev)
1937{
1938 struct msm_otg *motg = dev_get_drvdata(dev);
1939
1940 dev_dbg(dev, "OTG PM suspend\n");
1941 return msm_otg_suspend(motg);
1942}
1943
1944static int msm_otg_pm_resume(struct device *dev)
1945{
1946 struct msm_otg *motg = dev_get_drvdata(dev);
1947 int ret;
1948
1949 dev_dbg(dev, "OTG PM resume\n");
1950
1951 ret = msm_otg_resume(motg);
1952 if (ret)
1953 return ret;
1954
1955 /*
1956 * Runtime PM Documentation recommends bringing the
1957 * device to full powered state upon resume.
1958 */
1959 pm_runtime_disable(dev);
1960 pm_runtime_set_active(dev);
1961 pm_runtime_enable(dev);
1962
1963 return 0;
1964}
1965#endif
1966
1967static const struct dev_pm_ops msm_otg_dev_pm_ops = {
1968 SET_SYSTEM_SLEEP_PM_OPS(msm_otg_pm_suspend, msm_otg_pm_resume)
1969 SET_RUNTIME_PM_OPS(msm_otg_runtime_suspend, msm_otg_runtime_resume,
1970 msm_otg_runtime_idle)
1971};
1972
1973static struct platform_driver msm_otg_driver = {
1974 .probe = msm_otg_probe,
1975 .remove = msm_otg_remove,
1976 .driver = {
1977 .name = DRIVER_NAME,
1978 .pm = &msm_otg_dev_pm_ops,
1979 .of_match_table = msm_otg_dt_match,
1980 },
1981};
1982
1983module_platform_driver(msm_otg_driver);
1984
1985MODULE_LICENSE("GPL v2");
1986MODULE_DESCRIPTION("MSM USB transceiver driver");
1/* Copyright (c) 2009-2011, Code Aurora Forum. All rights reserved.
2 *
3 * This program is free software; you can redistribute it and/or modify
4 * it under the terms of the GNU General Public License version 2 and
5 * only version 2 as published by the Free Software Foundation.
6 *
7 * This program is distributed in the hope that it will be useful,
8 * but WITHOUT ANY WARRANTY; without even the implied warranty of
9 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
10 * GNU General Public License for more details.
11 *
12 * You should have received a copy of the GNU General Public License
13 * along with this program; if not, write to the Free Software
14 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
15 * 02110-1301, USA.
16 *
17 */
18
19#include <linux/module.h>
20#include <linux/device.h>
21#include <linux/extcon.h>
22#include <linux/gpio/consumer.h>
23#include <linux/platform_device.h>
24#include <linux/clk.h>
25#include <linux/slab.h>
26#include <linux/interrupt.h>
27#include <linux/err.h>
28#include <linux/delay.h>
29#include <linux/io.h>
30#include <linux/ioport.h>
31#include <linux/uaccess.h>
32#include <linux/debugfs.h>
33#include <linux/seq_file.h>
34#include <linux/pm_runtime.h>
35#include <linux/of.h>
36#include <linux/of_device.h>
37#include <linux/reboot.h>
38#include <linux/reset.h>
39#include <linux/types.h>
40#include <linux/usb/otg.h>
41
42#include <linux/usb.h>
43#include <linux/usb/otg.h>
44#include <linux/usb/of.h>
45#include <linux/usb/ulpi.h>
46#include <linux/usb/gadget.h>
47#include <linux/usb/hcd.h>
48#include <linux/usb/msm_hsusb_hw.h>
49#include <linux/regulator/consumer.h>
50
51/**
52 * OTG control
53 *
54 * OTG_NO_CONTROL Id/VBUS notifications not required. Useful in host
55 * only configuration.
56 * OTG_PHY_CONTROL Id/VBUS notifications comes form USB PHY.
57 * OTG_PMIC_CONTROL Id/VBUS notifications comes from PMIC hardware.
58 * OTG_USER_CONTROL Id/VBUS notifcations comes from User via sysfs.
59 *
60 */
61enum otg_control_type {
62 OTG_NO_CONTROL = 0,
63 OTG_PHY_CONTROL,
64 OTG_PMIC_CONTROL,
65 OTG_USER_CONTROL,
66};
67
68/**
69 * PHY used in
70 *
71 * INVALID_PHY Unsupported PHY
72 * CI_45NM_INTEGRATED_PHY Chipidea 45nm integrated PHY
73 * SNPS_28NM_INTEGRATED_PHY Synopsis 28nm integrated PHY
74 *
75 */
76enum msm_usb_phy_type {
77 INVALID_PHY = 0,
78 CI_45NM_INTEGRATED_PHY,
79 SNPS_28NM_INTEGRATED_PHY,
80};
81
82#define IDEV_CHG_MAX 1500
83#define IUNIT 100
84
85/**
86 * Different states involved in USB charger detection.
87 *
88 * USB_CHG_STATE_UNDEFINED USB charger is not connected or detection
89 * process is not yet started.
90 * USB_CHG_STATE_WAIT_FOR_DCD Waiting for Data pins contact.
91 * USB_CHG_STATE_DCD_DONE Data pin contact is detected.
92 * USB_CHG_STATE_PRIMARY_DONE Primary detection is completed (Detects
93 * between SDP and DCP/CDP).
94 * USB_CHG_STATE_SECONDARY_DONE Secondary detection is completed (Detects
95 * between DCP and CDP).
96 * USB_CHG_STATE_DETECTED USB charger type is determined.
97 *
98 */
99enum usb_chg_state {
100 USB_CHG_STATE_UNDEFINED = 0,
101 USB_CHG_STATE_WAIT_FOR_DCD,
102 USB_CHG_STATE_DCD_DONE,
103 USB_CHG_STATE_PRIMARY_DONE,
104 USB_CHG_STATE_SECONDARY_DONE,
105 USB_CHG_STATE_DETECTED,
106};
107
108/**
109 * USB charger types
110 *
111 * USB_INVALID_CHARGER Invalid USB charger.
112 * USB_SDP_CHARGER Standard downstream port. Refers to a downstream port
113 * on USB2.0 compliant host/hub.
114 * USB_DCP_CHARGER Dedicated charger port (AC charger/ Wall charger).
115 * USB_CDP_CHARGER Charging downstream port. Enumeration can happen and
116 * IDEV_CHG_MAX can be drawn irrespective of USB state.
117 *
118 */
119enum usb_chg_type {
120 USB_INVALID_CHARGER = 0,
121 USB_SDP_CHARGER,
122 USB_DCP_CHARGER,
123 USB_CDP_CHARGER,
124};
125
126/**
127 * struct msm_otg_platform_data - platform device data
128 * for msm_otg driver.
129 * @phy_init_seq: PHY configuration sequence values. Value of -1 is reserved as
130 * "do not overwrite default vaule at this address".
131 * @phy_init_sz: PHY configuration sequence size.
132 * @vbus_power: VBUS power on/off routine.
133 * @power_budget: VBUS power budget in mA (0 will be treated as 500mA).
134 * @mode: Supported mode (OTG/peripheral/host).
135 * @otg_control: OTG switch controlled by user/Id pin
136 */
137struct msm_otg_platform_data {
138 int *phy_init_seq;
139 int phy_init_sz;
140 void (*vbus_power)(bool on);
141 unsigned power_budget;
142 enum usb_dr_mode mode;
143 enum otg_control_type otg_control;
144 enum msm_usb_phy_type phy_type;
145 void (*setup_gpio)(enum usb_otg_state state);
146};
147
148/**
149 * struct msm_usb_cable - structure for exteternal connector cable
150 * state tracking
151 * @nb: hold event notification callback
152 * @conn: used for notification registration
153 */
154struct msm_usb_cable {
155 struct notifier_block nb;
156 struct extcon_dev *extcon;
157};
158
159/**
160 * struct msm_otg: OTG driver data. Shared by HCD and DCD.
161 * @otg: USB OTG Transceiver structure.
162 * @pdata: otg device platform data.
163 * @irq: IRQ number assigned for HSUSB controller.
164 * @clk: clock struct of usb_hs_clk.
165 * @pclk: clock struct of usb_hs_pclk.
166 * @core_clk: clock struct of usb_hs_core_clk.
167 * @regs: ioremapped register base address.
168 * @inputs: OTG state machine inputs(Id, SessValid etc).
169 * @sm_work: OTG state machine work.
170 * @in_lpm: indicates low power mode (LPM) state.
171 * @async_int: Async interrupt arrived.
172 * @cur_power: The amount of mA available from downstream port.
173 * @chg_work: Charger detection work.
174 * @chg_state: The state of charger detection process.
175 * @chg_type: The type of charger attached.
176 * @dcd_retires: The retry count used to track Data contact
177 * detection process.
178 * @manual_pullup: true if VBUS is not routed to USB controller/phy
179 * and controller driver therefore enables pull-up explicitly before
180 * starting controller using usbcmd run/stop bit.
181 * @vbus: VBUS signal state trakining, using extcon framework
182 * @id: ID signal state trakining, using extcon framework
183 * @switch_gpio: Descriptor for GPIO used to control external Dual
184 * SPDT USB Switch.
185 * @reboot: Used to inform the driver to route USB D+/D- line to Device
186 * connector
187 */
188struct msm_otg {
189 struct usb_phy phy;
190 struct msm_otg_platform_data *pdata;
191 int irq;
192 struct clk *clk;
193 struct clk *pclk;
194 struct clk *core_clk;
195 void __iomem *regs;
196#define ID 0
197#define B_SESS_VLD 1
198 unsigned long inputs;
199 struct work_struct sm_work;
200 atomic_t in_lpm;
201 int async_int;
202 unsigned cur_power;
203 int phy_number;
204 struct delayed_work chg_work;
205 enum usb_chg_state chg_state;
206 enum usb_chg_type chg_type;
207 u8 dcd_retries;
208 struct regulator *v3p3;
209 struct regulator *v1p8;
210 struct regulator *vddcx;
211
212 struct reset_control *phy_rst;
213 struct reset_control *link_rst;
214 int vdd_levels[3];
215
216 bool manual_pullup;
217
218 struct msm_usb_cable vbus;
219 struct msm_usb_cable id;
220
221 struct gpio_desc *switch_gpio;
222 struct notifier_block reboot;
223};
224
225#define MSM_USB_BASE (motg->regs)
226#define DRIVER_NAME "msm_otg"
227
228#define ULPI_IO_TIMEOUT_USEC (10 * 1000)
229#define LINK_RESET_TIMEOUT_USEC (250 * 1000)
230
231#define USB_PHY_3P3_VOL_MIN 3050000 /* uV */
232#define USB_PHY_3P3_VOL_MAX 3300000 /* uV */
233#define USB_PHY_3P3_HPM_LOAD 50000 /* uA */
234#define USB_PHY_3P3_LPM_LOAD 4000 /* uA */
235
236#define USB_PHY_1P8_VOL_MIN 1800000 /* uV */
237#define USB_PHY_1P8_VOL_MAX 1800000 /* uV */
238#define USB_PHY_1P8_HPM_LOAD 50000 /* uA */
239#define USB_PHY_1P8_LPM_LOAD 4000 /* uA */
240
241#define USB_PHY_VDD_DIG_VOL_MIN 1000000 /* uV */
242#define USB_PHY_VDD_DIG_VOL_MAX 1320000 /* uV */
243#define USB_PHY_SUSP_DIG_VOL 500000 /* uV */
244
245enum vdd_levels {
246 VDD_LEVEL_NONE = 0,
247 VDD_LEVEL_MIN,
248 VDD_LEVEL_MAX,
249};
250
251static int msm_hsusb_init_vddcx(struct msm_otg *motg, int init)
252{
253 int ret = 0;
254
255 if (init) {
256 ret = regulator_set_voltage(motg->vddcx,
257 motg->vdd_levels[VDD_LEVEL_MIN],
258 motg->vdd_levels[VDD_LEVEL_MAX]);
259 if (ret) {
260 dev_err(motg->phy.dev, "Cannot set vddcx voltage\n");
261 return ret;
262 }
263
264 ret = regulator_enable(motg->vddcx);
265 if (ret)
266 dev_err(motg->phy.dev, "unable to enable hsusb vddcx\n");
267 } else {
268 ret = regulator_set_voltage(motg->vddcx, 0,
269 motg->vdd_levels[VDD_LEVEL_MAX]);
270 if (ret)
271 dev_err(motg->phy.dev, "Cannot set vddcx voltage\n");
272 ret = regulator_disable(motg->vddcx);
273 if (ret)
274 dev_err(motg->phy.dev, "unable to disable hsusb vddcx\n");
275 }
276
277 return ret;
278}
279
280static int msm_hsusb_ldo_init(struct msm_otg *motg, int init)
281{
282 int rc = 0;
283
284 if (init) {
285 rc = regulator_set_voltage(motg->v3p3, USB_PHY_3P3_VOL_MIN,
286 USB_PHY_3P3_VOL_MAX);
287 if (rc) {
288 dev_err(motg->phy.dev, "Cannot set v3p3 voltage\n");
289 goto exit;
290 }
291 rc = regulator_enable(motg->v3p3);
292 if (rc) {
293 dev_err(motg->phy.dev, "unable to enable the hsusb 3p3\n");
294 goto exit;
295 }
296 rc = regulator_set_voltage(motg->v1p8, USB_PHY_1P8_VOL_MIN,
297 USB_PHY_1P8_VOL_MAX);
298 if (rc) {
299 dev_err(motg->phy.dev, "Cannot set v1p8 voltage\n");
300 goto disable_3p3;
301 }
302 rc = regulator_enable(motg->v1p8);
303 if (rc) {
304 dev_err(motg->phy.dev, "unable to enable the hsusb 1p8\n");
305 goto disable_3p3;
306 }
307
308 return 0;
309 }
310
311 regulator_disable(motg->v1p8);
312disable_3p3:
313 regulator_disable(motg->v3p3);
314exit:
315 return rc;
316}
317
318static int msm_hsusb_ldo_set_mode(struct msm_otg *motg, int on)
319{
320 int ret = 0;
321
322 if (on) {
323 ret = regulator_set_load(motg->v1p8, USB_PHY_1P8_HPM_LOAD);
324 if (ret < 0) {
325 pr_err("Could not set HPM for v1p8\n");
326 return ret;
327 }
328 ret = regulator_set_load(motg->v3p3, USB_PHY_3P3_HPM_LOAD);
329 if (ret < 0) {
330 pr_err("Could not set HPM for v3p3\n");
331 regulator_set_load(motg->v1p8, USB_PHY_1P8_LPM_LOAD);
332 return ret;
333 }
334 } else {
335 ret = regulator_set_load(motg->v1p8, USB_PHY_1P8_LPM_LOAD);
336 if (ret < 0)
337 pr_err("Could not set LPM for v1p8\n");
338 ret = regulator_set_load(motg->v3p3, USB_PHY_3P3_LPM_LOAD);
339 if (ret < 0)
340 pr_err("Could not set LPM for v3p3\n");
341 }
342
343 pr_debug("reg (%s)\n", on ? "HPM" : "LPM");
344 return ret < 0 ? ret : 0;
345}
346
347static int ulpi_read(struct usb_phy *phy, u32 reg)
348{
349 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
350 int cnt = 0;
351
352 /* initiate read operation */
353 writel(ULPI_RUN | ULPI_READ | ULPI_ADDR(reg),
354 USB_ULPI_VIEWPORT);
355
356 /* wait for completion */
357 while (cnt < ULPI_IO_TIMEOUT_USEC) {
358 if (!(readl(USB_ULPI_VIEWPORT) & ULPI_RUN))
359 break;
360 udelay(1);
361 cnt++;
362 }
363
364 if (cnt >= ULPI_IO_TIMEOUT_USEC) {
365 dev_err(phy->dev, "ulpi_read: timeout %08x\n",
366 readl(USB_ULPI_VIEWPORT));
367 return -ETIMEDOUT;
368 }
369 return ULPI_DATA_READ(readl(USB_ULPI_VIEWPORT));
370}
371
372static int ulpi_write(struct usb_phy *phy, u32 val, u32 reg)
373{
374 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
375 int cnt = 0;
376
377 /* initiate write operation */
378 writel(ULPI_RUN | ULPI_WRITE |
379 ULPI_ADDR(reg) | ULPI_DATA(val),
380 USB_ULPI_VIEWPORT);
381
382 /* wait for completion */
383 while (cnt < ULPI_IO_TIMEOUT_USEC) {
384 if (!(readl(USB_ULPI_VIEWPORT) & ULPI_RUN))
385 break;
386 udelay(1);
387 cnt++;
388 }
389
390 if (cnt >= ULPI_IO_TIMEOUT_USEC) {
391 dev_err(phy->dev, "ulpi_write: timeout\n");
392 return -ETIMEDOUT;
393 }
394 return 0;
395}
396
397static struct usb_phy_io_ops msm_otg_io_ops = {
398 .read = ulpi_read,
399 .write = ulpi_write,
400};
401
402static void ulpi_init(struct msm_otg *motg)
403{
404 struct msm_otg_platform_data *pdata = motg->pdata;
405 int *seq = pdata->phy_init_seq, idx;
406 u32 addr = ULPI_EXT_VENDOR_SPECIFIC;
407
408 for (idx = 0; idx < pdata->phy_init_sz; idx++) {
409 if (seq[idx] == -1)
410 continue;
411
412 dev_vdbg(motg->phy.dev, "ulpi: write 0x%02x to 0x%02x\n",
413 seq[idx], addr + idx);
414 ulpi_write(&motg->phy, seq[idx], addr + idx);
415 }
416}
417
418static int msm_phy_notify_disconnect(struct usb_phy *phy,
419 enum usb_device_speed speed)
420{
421 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
422 int val;
423
424 if (motg->manual_pullup) {
425 val = ULPI_MISC_A_VBUSVLDEXT | ULPI_MISC_A_VBUSVLDEXTSEL;
426 usb_phy_io_write(phy, val, ULPI_CLR(ULPI_MISC_A));
427 }
428
429 /*
430 * Put the transceiver in non-driving mode. Otherwise host
431 * may not detect soft-disconnection.
432 */
433 val = ulpi_read(phy, ULPI_FUNC_CTRL);
434 val &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
435 val |= ULPI_FUNC_CTRL_OPMODE_NONDRIVING;
436 ulpi_write(phy, val, ULPI_FUNC_CTRL);
437
438 return 0;
439}
440
441static int msm_otg_link_clk_reset(struct msm_otg *motg, bool assert)
442{
443 int ret;
444
445 if (assert)
446 ret = reset_control_assert(motg->link_rst);
447 else
448 ret = reset_control_deassert(motg->link_rst);
449
450 if (ret)
451 dev_err(motg->phy.dev, "usb link clk reset %s failed\n",
452 assert ? "assert" : "deassert");
453
454 return ret;
455}
456
457static int msm_otg_phy_clk_reset(struct msm_otg *motg)
458{
459 int ret = 0;
460
461 if (motg->phy_rst)
462 ret = reset_control_reset(motg->phy_rst);
463
464 if (ret)
465 dev_err(motg->phy.dev, "usb phy clk reset failed\n");
466
467 return ret;
468}
469
470static int msm_link_reset(struct msm_otg *motg)
471{
472 u32 val;
473 int ret;
474
475 ret = msm_otg_link_clk_reset(motg, 1);
476 if (ret)
477 return ret;
478
479 /* wait for 1ms delay as suggested in HPG. */
480 usleep_range(1000, 1200);
481
482 ret = msm_otg_link_clk_reset(motg, 0);
483 if (ret)
484 return ret;
485
486 if (motg->phy_number)
487 writel(readl(USB_PHY_CTRL2) | BIT(16), USB_PHY_CTRL2);
488
489 /* put transceiver in serial mode as part of reset */
490 val = readl(USB_PORTSC) & ~PORTSC_PTS_MASK;
491 writel(val | PORTSC_PTS_SERIAL, USB_PORTSC);
492
493 return 0;
494}
495
496static int msm_otg_reset(struct usb_phy *phy)
497{
498 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
499 int cnt = 0;
500
501 writel(USBCMD_RESET, USB_USBCMD);
502 while (cnt < LINK_RESET_TIMEOUT_USEC) {
503 if (!(readl(USB_USBCMD) & USBCMD_RESET))
504 break;
505 udelay(1);
506 cnt++;
507 }
508 if (cnt >= LINK_RESET_TIMEOUT_USEC)
509 return -ETIMEDOUT;
510
511 /* select ULPI phy and clear other status/control bits in PORTSC */
512 writel(PORTSC_PTS_ULPI, USB_PORTSC);
513
514 writel(0x0, USB_AHBBURST);
515 writel(0x08, USB_AHBMODE);
516
517 if (motg->phy_number)
518 writel(readl(USB_PHY_CTRL2) | BIT(16), USB_PHY_CTRL2);
519 return 0;
520}
521
522static void msm_phy_reset(struct msm_otg *motg)
523{
524 void __iomem *addr;
525
526 if (motg->pdata->phy_type != SNPS_28NM_INTEGRATED_PHY) {
527 msm_otg_phy_clk_reset(motg);
528 return;
529 }
530
531 addr = USB_PHY_CTRL;
532 if (motg->phy_number)
533 addr = USB_PHY_CTRL2;
534
535 /* Assert USB PHY_POR */
536 writel(readl(addr) | PHY_POR_ASSERT, addr);
537
538 /*
539 * wait for minimum 10 microseconds as suggested in HPG.
540 * Use a slightly larger value since the exact value didn't
541 * work 100% of the time.
542 */
543 udelay(12);
544
545 /* Deassert USB PHY_POR */
546 writel(readl(addr) & ~PHY_POR_ASSERT, addr);
547}
548
549static int msm_usb_reset(struct usb_phy *phy)
550{
551 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
552 int ret;
553
554 if (!IS_ERR(motg->core_clk))
555 clk_prepare_enable(motg->core_clk);
556
557 ret = msm_link_reset(motg);
558 if (ret) {
559 dev_err(phy->dev, "phy_reset failed\n");
560 return ret;
561 }
562
563 ret = msm_otg_reset(&motg->phy);
564 if (ret) {
565 dev_err(phy->dev, "link reset failed\n");
566 return ret;
567 }
568
569 msleep(100);
570
571 /* Reset USB PHY after performing USB Link RESET */
572 msm_phy_reset(motg);
573
574 if (!IS_ERR(motg->core_clk))
575 clk_disable_unprepare(motg->core_clk);
576
577 return 0;
578}
579
580static int msm_phy_init(struct usb_phy *phy)
581{
582 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
583 struct msm_otg_platform_data *pdata = motg->pdata;
584 u32 val, ulpi_val = 0;
585
586 /* Program USB PHY Override registers. */
587 ulpi_init(motg);
588
589 /*
590 * It is recommended in HPG to reset USB PHY after programming
591 * USB PHY Override registers.
592 */
593 msm_phy_reset(motg);
594
595 if (pdata->otg_control == OTG_PHY_CONTROL) {
596 val = readl(USB_OTGSC);
597 if (pdata->mode == USB_DR_MODE_OTG) {
598 ulpi_val = ULPI_INT_IDGRD | ULPI_INT_SESS_VALID;
599 val |= OTGSC_IDIE | OTGSC_BSVIE;
600 } else if (pdata->mode == USB_DR_MODE_PERIPHERAL) {
601 ulpi_val = ULPI_INT_SESS_VALID;
602 val |= OTGSC_BSVIE;
603 }
604 writel(val, USB_OTGSC);
605 ulpi_write(phy, ulpi_val, ULPI_USB_INT_EN_RISE);
606 ulpi_write(phy, ulpi_val, ULPI_USB_INT_EN_FALL);
607 }
608
609 if (motg->manual_pullup) {
610 val = ULPI_MISC_A_VBUSVLDEXTSEL | ULPI_MISC_A_VBUSVLDEXT;
611 ulpi_write(phy, val, ULPI_SET(ULPI_MISC_A));
612
613 val = readl(USB_GENCONFIG_2);
614 val |= GENCONFIG_2_SESS_VLD_CTRL_EN;
615 writel(val, USB_GENCONFIG_2);
616
617 val = readl(USB_USBCMD);
618 val |= USBCMD_SESS_VLD_CTRL;
619 writel(val, USB_USBCMD);
620
621 val = ulpi_read(phy, ULPI_FUNC_CTRL);
622 val &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
623 val |= ULPI_FUNC_CTRL_OPMODE_NORMAL;
624 ulpi_write(phy, val, ULPI_FUNC_CTRL);
625 }
626
627 if (motg->phy_number)
628 writel(readl(USB_PHY_CTRL2) | BIT(16), USB_PHY_CTRL2);
629
630 return 0;
631}
632
633#define PHY_SUSPEND_TIMEOUT_USEC (500 * 1000)
634#define PHY_RESUME_TIMEOUT_USEC (100 * 1000)
635
636#ifdef CONFIG_PM
637
638static int msm_hsusb_config_vddcx(struct msm_otg *motg, int high)
639{
640 int max_vol = motg->vdd_levels[VDD_LEVEL_MAX];
641 int min_vol;
642 int ret;
643
644 if (high)
645 min_vol = motg->vdd_levels[VDD_LEVEL_MIN];
646 else
647 min_vol = motg->vdd_levels[VDD_LEVEL_NONE];
648
649 ret = regulator_set_voltage(motg->vddcx, min_vol, max_vol);
650 if (ret) {
651 pr_err("Cannot set vddcx voltage\n");
652 return ret;
653 }
654
655 pr_debug("%s: min_vol:%d max_vol:%d\n", __func__, min_vol, max_vol);
656
657 return ret;
658}
659
660static int msm_otg_suspend(struct msm_otg *motg)
661{
662 struct usb_phy *phy = &motg->phy;
663 struct usb_bus *bus = phy->otg->host;
664 struct msm_otg_platform_data *pdata = motg->pdata;
665 void __iomem *addr;
666 int cnt = 0;
667
668 if (atomic_read(&motg->in_lpm))
669 return 0;
670
671 disable_irq(motg->irq);
672 /*
673 * Chipidea 45-nm PHY suspend sequence:
674 *
675 * Interrupt Latch Register auto-clear feature is not present
676 * in all PHY versions. Latch register is clear on read type.
677 * Clear latch register to avoid spurious wakeup from
678 * low power mode (LPM).
679 *
680 * PHY comparators are disabled when PHY enters into low power
681 * mode (LPM). Keep PHY comparators ON in LPM only when we expect
682 * VBUS/Id notifications from USB PHY. Otherwise turn off USB
683 * PHY comparators. This save significant amount of power.
684 *
685 * PLL is not turned off when PHY enters into low power mode (LPM).
686 * Disable PLL for maximum power savings.
687 */
688
689 if (motg->pdata->phy_type == CI_45NM_INTEGRATED_PHY) {
690 ulpi_read(phy, 0x14);
691 if (pdata->otg_control == OTG_PHY_CONTROL)
692 ulpi_write(phy, 0x01, 0x30);
693 ulpi_write(phy, 0x08, 0x09);
694 }
695
696 /*
697 * PHY may take some time or even fail to enter into low power
698 * mode (LPM). Hence poll for 500 msec and reset the PHY and link
699 * in failure case.
700 */
701 writel(readl(USB_PORTSC) | PORTSC_PHCD, USB_PORTSC);
702 while (cnt < PHY_SUSPEND_TIMEOUT_USEC) {
703 if (readl(USB_PORTSC) & PORTSC_PHCD)
704 break;
705 udelay(1);
706 cnt++;
707 }
708
709 if (cnt >= PHY_SUSPEND_TIMEOUT_USEC) {
710 dev_err(phy->dev, "Unable to suspend PHY\n");
711 msm_otg_reset(phy);
712 enable_irq(motg->irq);
713 return -ETIMEDOUT;
714 }
715
716 /*
717 * PHY has capability to generate interrupt asynchronously in low
718 * power mode (LPM). This interrupt is level triggered. So USB IRQ
719 * line must be disabled till async interrupt enable bit is cleared
720 * in USBCMD register. Assert STP (ULPI interface STOP signal) to
721 * block data communication from PHY.
722 */
723 writel(readl(USB_USBCMD) | ASYNC_INTR_CTRL | ULPI_STP_CTRL, USB_USBCMD);
724
725 addr = USB_PHY_CTRL;
726 if (motg->phy_number)
727 addr = USB_PHY_CTRL2;
728
729 if (motg->pdata->phy_type == SNPS_28NM_INTEGRATED_PHY &&
730 motg->pdata->otg_control == OTG_PMIC_CONTROL)
731 writel(readl(addr) | PHY_RETEN, addr);
732
733 clk_disable_unprepare(motg->pclk);
734 clk_disable_unprepare(motg->clk);
735 if (!IS_ERR(motg->core_clk))
736 clk_disable_unprepare(motg->core_clk);
737
738 if (motg->pdata->phy_type == SNPS_28NM_INTEGRATED_PHY &&
739 motg->pdata->otg_control == OTG_PMIC_CONTROL) {
740 msm_hsusb_ldo_set_mode(motg, 0);
741 msm_hsusb_config_vddcx(motg, 0);
742 }
743
744 if (device_may_wakeup(phy->dev))
745 enable_irq_wake(motg->irq);
746 if (bus)
747 clear_bit(HCD_FLAG_HW_ACCESSIBLE, &(bus_to_hcd(bus))->flags);
748
749 atomic_set(&motg->in_lpm, 1);
750 enable_irq(motg->irq);
751
752 dev_info(phy->dev, "USB in low power mode\n");
753
754 return 0;
755}
756
757static int msm_otg_resume(struct msm_otg *motg)
758{
759 struct usb_phy *phy = &motg->phy;
760 struct usb_bus *bus = phy->otg->host;
761 void __iomem *addr;
762 int cnt = 0;
763 unsigned temp;
764
765 if (!atomic_read(&motg->in_lpm))
766 return 0;
767
768 clk_prepare_enable(motg->pclk);
769 clk_prepare_enable(motg->clk);
770 if (!IS_ERR(motg->core_clk))
771 clk_prepare_enable(motg->core_clk);
772
773 if (motg->pdata->phy_type == SNPS_28NM_INTEGRATED_PHY &&
774 motg->pdata->otg_control == OTG_PMIC_CONTROL) {
775
776 addr = USB_PHY_CTRL;
777 if (motg->phy_number)
778 addr = USB_PHY_CTRL2;
779
780 msm_hsusb_ldo_set_mode(motg, 1);
781 msm_hsusb_config_vddcx(motg, 1);
782 writel(readl(addr) & ~PHY_RETEN, addr);
783 }
784
785 temp = readl(USB_USBCMD);
786 temp &= ~ASYNC_INTR_CTRL;
787 temp &= ~ULPI_STP_CTRL;
788 writel(temp, USB_USBCMD);
789
790 /*
791 * PHY comes out of low power mode (LPM) in case of wakeup
792 * from asynchronous interrupt.
793 */
794 if (!(readl(USB_PORTSC) & PORTSC_PHCD))
795 goto skip_phy_resume;
796
797 writel(readl(USB_PORTSC) & ~PORTSC_PHCD, USB_PORTSC);
798 while (cnt < PHY_RESUME_TIMEOUT_USEC) {
799 if (!(readl(USB_PORTSC) & PORTSC_PHCD))
800 break;
801 udelay(1);
802 cnt++;
803 }
804
805 if (cnt >= PHY_RESUME_TIMEOUT_USEC) {
806 /*
807 * This is a fatal error. Reset the link and
808 * PHY. USB state can not be restored. Re-insertion
809 * of USB cable is the only way to get USB working.
810 */
811 dev_err(phy->dev, "Unable to resume USB. Re-plugin the cable\n");
812 msm_otg_reset(phy);
813 }
814
815skip_phy_resume:
816 if (device_may_wakeup(phy->dev))
817 disable_irq_wake(motg->irq);
818 if (bus)
819 set_bit(HCD_FLAG_HW_ACCESSIBLE, &(bus_to_hcd(bus))->flags);
820
821 atomic_set(&motg->in_lpm, 0);
822
823 if (motg->async_int) {
824 motg->async_int = 0;
825 pm_runtime_put(phy->dev);
826 enable_irq(motg->irq);
827 }
828
829 dev_info(phy->dev, "USB exited from low power mode\n");
830
831 return 0;
832}
833#endif
834
835static void msm_otg_notify_charger(struct msm_otg *motg, unsigned mA)
836{
837 if (motg->cur_power == mA)
838 return;
839
840 /* TODO: Notify PMIC about available current */
841 dev_info(motg->phy.dev, "Avail curr from USB = %u\n", mA);
842 motg->cur_power = mA;
843}
844
845static int msm_otg_set_power(struct usb_phy *phy, unsigned mA)
846{
847 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
848
849 /*
850 * Gadget driver uses set_power method to notify about the
851 * available current based on suspend/configured states.
852 *
853 * IDEV_CHG can be drawn irrespective of suspend/un-configured
854 * states when CDP/ACA is connected.
855 */
856 if (motg->chg_type == USB_SDP_CHARGER)
857 msm_otg_notify_charger(motg, mA);
858
859 return 0;
860}
861
862static void msm_otg_start_host(struct usb_phy *phy, int on)
863{
864 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
865 struct msm_otg_platform_data *pdata = motg->pdata;
866 struct usb_hcd *hcd;
867
868 if (!phy->otg->host)
869 return;
870
871 hcd = bus_to_hcd(phy->otg->host);
872
873 if (on) {
874 dev_dbg(phy->dev, "host on\n");
875
876 if (pdata->vbus_power)
877 pdata->vbus_power(1);
878 /*
879 * Some boards have a switch cotrolled by gpio
880 * to enable/disable internal HUB. Enable internal
881 * HUB before kicking the host.
882 */
883 if (pdata->setup_gpio)
884 pdata->setup_gpio(OTG_STATE_A_HOST);
885#ifdef CONFIG_USB
886 usb_add_hcd(hcd, hcd->irq, IRQF_SHARED);
887 device_wakeup_enable(hcd->self.controller);
888#endif
889 } else {
890 dev_dbg(phy->dev, "host off\n");
891
892#ifdef CONFIG_USB
893 usb_remove_hcd(hcd);
894#endif
895 if (pdata->setup_gpio)
896 pdata->setup_gpio(OTG_STATE_UNDEFINED);
897 if (pdata->vbus_power)
898 pdata->vbus_power(0);
899 }
900}
901
902static int msm_otg_set_host(struct usb_otg *otg, struct usb_bus *host)
903{
904 struct msm_otg *motg = container_of(otg->usb_phy, struct msm_otg, phy);
905 struct usb_hcd *hcd;
906
907 /*
908 * Fail host registration if this board can support
909 * only peripheral configuration.
910 */
911 if (motg->pdata->mode == USB_DR_MODE_PERIPHERAL) {
912 dev_info(otg->usb_phy->dev, "Host mode is not supported\n");
913 return -ENODEV;
914 }
915
916 if (!host) {
917 if (otg->state == OTG_STATE_A_HOST) {
918 pm_runtime_get_sync(otg->usb_phy->dev);
919 msm_otg_start_host(otg->usb_phy, 0);
920 otg->host = NULL;
921 otg->state = OTG_STATE_UNDEFINED;
922 schedule_work(&motg->sm_work);
923 } else {
924 otg->host = NULL;
925 }
926
927 return 0;
928 }
929
930 hcd = bus_to_hcd(host);
931 hcd->power_budget = motg->pdata->power_budget;
932
933 otg->host = host;
934 dev_dbg(otg->usb_phy->dev, "host driver registered w/ tranceiver\n");
935
936 pm_runtime_get_sync(otg->usb_phy->dev);
937 schedule_work(&motg->sm_work);
938
939 return 0;
940}
941
942static void msm_otg_start_peripheral(struct usb_phy *phy, int on)
943{
944 struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
945 struct msm_otg_platform_data *pdata = motg->pdata;
946
947 if (!phy->otg->gadget)
948 return;
949
950 if (on) {
951 dev_dbg(phy->dev, "gadget on\n");
952 /*
953 * Some boards have a switch cotrolled by gpio
954 * to enable/disable internal HUB. Disable internal
955 * HUB before kicking the gadget.
956 */
957 if (pdata->setup_gpio)
958 pdata->setup_gpio(OTG_STATE_B_PERIPHERAL);
959 usb_gadget_vbus_connect(phy->otg->gadget);
960 } else {
961 dev_dbg(phy->dev, "gadget off\n");
962 usb_gadget_vbus_disconnect(phy->otg->gadget);
963 if (pdata->setup_gpio)
964 pdata->setup_gpio(OTG_STATE_UNDEFINED);
965 }
966
967}
968
969static int msm_otg_set_peripheral(struct usb_otg *otg,
970 struct usb_gadget *gadget)
971{
972 struct msm_otg *motg = container_of(otg->usb_phy, struct msm_otg, phy);
973
974 /*
975 * Fail peripheral registration if this board can support
976 * only host configuration.
977 */
978 if (motg->pdata->mode == USB_DR_MODE_HOST) {
979 dev_info(otg->usb_phy->dev, "Peripheral mode is not supported\n");
980 return -ENODEV;
981 }
982
983 if (!gadget) {
984 if (otg->state == OTG_STATE_B_PERIPHERAL) {
985 pm_runtime_get_sync(otg->usb_phy->dev);
986 msm_otg_start_peripheral(otg->usb_phy, 0);
987 otg->gadget = NULL;
988 otg->state = OTG_STATE_UNDEFINED;
989 schedule_work(&motg->sm_work);
990 } else {
991 otg->gadget = NULL;
992 }
993
994 return 0;
995 }
996 otg->gadget = gadget;
997 dev_dbg(otg->usb_phy->dev,
998 "peripheral driver registered w/ tranceiver\n");
999
1000 pm_runtime_get_sync(otg->usb_phy->dev);
1001 schedule_work(&motg->sm_work);
1002
1003 return 0;
1004}
1005
1006static bool msm_chg_check_secondary_det(struct msm_otg *motg)
1007{
1008 struct usb_phy *phy = &motg->phy;
1009 u32 chg_det;
1010 bool ret = false;
1011
1012 switch (motg->pdata->phy_type) {
1013 case CI_45NM_INTEGRATED_PHY:
1014 chg_det = ulpi_read(phy, 0x34);
1015 ret = chg_det & (1 << 4);
1016 break;
1017 case SNPS_28NM_INTEGRATED_PHY:
1018 chg_det = ulpi_read(phy, 0x87);
1019 ret = chg_det & 1;
1020 break;
1021 default:
1022 break;
1023 }
1024 return ret;
1025}
1026
1027static void msm_chg_enable_secondary_det(struct msm_otg *motg)
1028{
1029 struct usb_phy *phy = &motg->phy;
1030 u32 chg_det;
1031
1032 switch (motg->pdata->phy_type) {
1033 case CI_45NM_INTEGRATED_PHY:
1034 chg_det = ulpi_read(phy, 0x34);
1035 /* Turn off charger block */
1036 chg_det |= ~(1 << 1);
1037 ulpi_write(phy, chg_det, 0x34);
1038 udelay(20);
1039 /* control chg block via ULPI */
1040 chg_det &= ~(1 << 3);
1041 ulpi_write(phy, chg_det, 0x34);
1042 /* put it in host mode for enabling D- source */
1043 chg_det &= ~(1 << 2);
1044 ulpi_write(phy, chg_det, 0x34);
1045 /* Turn on chg detect block */
1046 chg_det &= ~(1 << 1);
1047 ulpi_write(phy, chg_det, 0x34);
1048 udelay(20);
1049 /* enable chg detection */
1050 chg_det &= ~(1 << 0);
1051 ulpi_write(phy, chg_det, 0x34);
1052 break;
1053 case SNPS_28NM_INTEGRATED_PHY:
1054 /*
1055 * Configure DM as current source, DP as current sink
1056 * and enable battery charging comparators.
1057 */
1058 ulpi_write(phy, 0x8, 0x85);
1059 ulpi_write(phy, 0x2, 0x85);
1060 ulpi_write(phy, 0x1, 0x85);
1061 break;
1062 default:
1063 break;
1064 }
1065}
1066
1067static bool msm_chg_check_primary_det(struct msm_otg *motg)
1068{
1069 struct usb_phy *phy = &motg->phy;
1070 u32 chg_det;
1071 bool ret = false;
1072
1073 switch (motg->pdata->phy_type) {
1074 case CI_45NM_INTEGRATED_PHY:
1075 chg_det = ulpi_read(phy, 0x34);
1076 ret = chg_det & (1 << 4);
1077 break;
1078 case SNPS_28NM_INTEGRATED_PHY:
1079 chg_det = ulpi_read(phy, 0x87);
1080 ret = chg_det & 1;
1081 break;
1082 default:
1083 break;
1084 }
1085 return ret;
1086}
1087
1088static void msm_chg_enable_primary_det(struct msm_otg *motg)
1089{
1090 struct usb_phy *phy = &motg->phy;
1091 u32 chg_det;
1092
1093 switch (motg->pdata->phy_type) {
1094 case CI_45NM_INTEGRATED_PHY:
1095 chg_det = ulpi_read(phy, 0x34);
1096 /* enable chg detection */
1097 chg_det &= ~(1 << 0);
1098 ulpi_write(phy, chg_det, 0x34);
1099 break;
1100 case SNPS_28NM_INTEGRATED_PHY:
1101 /*
1102 * Configure DP as current source, DM as current sink
1103 * and enable battery charging comparators.
1104 */
1105 ulpi_write(phy, 0x2, 0x85);
1106 ulpi_write(phy, 0x1, 0x85);
1107 break;
1108 default:
1109 break;
1110 }
1111}
1112
1113static bool msm_chg_check_dcd(struct msm_otg *motg)
1114{
1115 struct usb_phy *phy = &motg->phy;
1116 u32 line_state;
1117 bool ret = false;
1118
1119 switch (motg->pdata->phy_type) {
1120 case CI_45NM_INTEGRATED_PHY:
1121 line_state = ulpi_read(phy, 0x15);
1122 ret = !(line_state & 1);
1123 break;
1124 case SNPS_28NM_INTEGRATED_PHY:
1125 line_state = ulpi_read(phy, 0x87);
1126 ret = line_state & 2;
1127 break;
1128 default:
1129 break;
1130 }
1131 return ret;
1132}
1133
1134static void msm_chg_disable_dcd(struct msm_otg *motg)
1135{
1136 struct usb_phy *phy = &motg->phy;
1137 u32 chg_det;
1138
1139 switch (motg->pdata->phy_type) {
1140 case CI_45NM_INTEGRATED_PHY:
1141 chg_det = ulpi_read(phy, 0x34);
1142 chg_det &= ~(1 << 5);
1143 ulpi_write(phy, chg_det, 0x34);
1144 break;
1145 case SNPS_28NM_INTEGRATED_PHY:
1146 ulpi_write(phy, 0x10, 0x86);
1147 break;
1148 default:
1149 break;
1150 }
1151}
1152
1153static void msm_chg_enable_dcd(struct msm_otg *motg)
1154{
1155 struct usb_phy *phy = &motg->phy;
1156 u32 chg_det;
1157
1158 switch (motg->pdata->phy_type) {
1159 case CI_45NM_INTEGRATED_PHY:
1160 chg_det = ulpi_read(phy, 0x34);
1161 /* Turn on D+ current source */
1162 chg_det |= (1 << 5);
1163 ulpi_write(phy, chg_det, 0x34);
1164 break;
1165 case SNPS_28NM_INTEGRATED_PHY:
1166 /* Data contact detection enable */
1167 ulpi_write(phy, 0x10, 0x85);
1168 break;
1169 default:
1170 break;
1171 }
1172}
1173
1174static void msm_chg_block_on(struct msm_otg *motg)
1175{
1176 struct usb_phy *phy = &motg->phy;
1177 u32 func_ctrl, chg_det;
1178
1179 /* put the controller in non-driving mode */
1180 func_ctrl = ulpi_read(phy, ULPI_FUNC_CTRL);
1181 func_ctrl &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
1182 func_ctrl |= ULPI_FUNC_CTRL_OPMODE_NONDRIVING;
1183 ulpi_write(phy, func_ctrl, ULPI_FUNC_CTRL);
1184
1185 switch (motg->pdata->phy_type) {
1186 case CI_45NM_INTEGRATED_PHY:
1187 chg_det = ulpi_read(phy, 0x34);
1188 /* control chg block via ULPI */
1189 chg_det &= ~(1 << 3);
1190 ulpi_write(phy, chg_det, 0x34);
1191 /* Turn on chg detect block */
1192 chg_det &= ~(1 << 1);
1193 ulpi_write(phy, chg_det, 0x34);
1194 udelay(20);
1195 break;
1196 case SNPS_28NM_INTEGRATED_PHY:
1197 /* Clear charger detecting control bits */
1198 ulpi_write(phy, 0x3F, 0x86);
1199 /* Clear alt interrupt latch and enable bits */
1200 ulpi_write(phy, 0x1F, 0x92);
1201 ulpi_write(phy, 0x1F, 0x95);
1202 udelay(100);
1203 break;
1204 default:
1205 break;
1206 }
1207}
1208
1209static void msm_chg_block_off(struct msm_otg *motg)
1210{
1211 struct usb_phy *phy = &motg->phy;
1212 u32 func_ctrl, chg_det;
1213
1214 switch (motg->pdata->phy_type) {
1215 case CI_45NM_INTEGRATED_PHY:
1216 chg_det = ulpi_read(phy, 0x34);
1217 /* Turn off charger block */
1218 chg_det |= ~(1 << 1);
1219 ulpi_write(phy, chg_det, 0x34);
1220 break;
1221 case SNPS_28NM_INTEGRATED_PHY:
1222 /* Clear charger detecting control bits */
1223 ulpi_write(phy, 0x3F, 0x86);
1224 /* Clear alt interrupt latch and enable bits */
1225 ulpi_write(phy, 0x1F, 0x92);
1226 ulpi_write(phy, 0x1F, 0x95);
1227 break;
1228 default:
1229 break;
1230 }
1231
1232 /* put the controller in normal mode */
1233 func_ctrl = ulpi_read(phy, ULPI_FUNC_CTRL);
1234 func_ctrl &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
1235 func_ctrl |= ULPI_FUNC_CTRL_OPMODE_NORMAL;
1236 ulpi_write(phy, func_ctrl, ULPI_FUNC_CTRL);
1237}
1238
1239#define MSM_CHG_DCD_POLL_TIME (100 * HZ/1000) /* 100 msec */
1240#define MSM_CHG_DCD_MAX_RETRIES 6 /* Tdcd_tmout = 6 * 100 msec */
1241#define MSM_CHG_PRIMARY_DET_TIME (40 * HZ/1000) /* TVDPSRC_ON */
1242#define MSM_CHG_SECONDARY_DET_TIME (40 * HZ/1000) /* TVDMSRC_ON */
1243static void msm_chg_detect_work(struct work_struct *w)
1244{
1245 struct msm_otg *motg = container_of(w, struct msm_otg, chg_work.work);
1246 struct usb_phy *phy = &motg->phy;
1247 bool is_dcd, tmout, vout;
1248 unsigned long delay;
1249
1250 dev_dbg(phy->dev, "chg detection work\n");
1251 switch (motg->chg_state) {
1252 case USB_CHG_STATE_UNDEFINED:
1253 pm_runtime_get_sync(phy->dev);
1254 msm_chg_block_on(motg);
1255 msm_chg_enable_dcd(motg);
1256 motg->chg_state = USB_CHG_STATE_WAIT_FOR_DCD;
1257 motg->dcd_retries = 0;
1258 delay = MSM_CHG_DCD_POLL_TIME;
1259 break;
1260 case USB_CHG_STATE_WAIT_FOR_DCD:
1261 is_dcd = msm_chg_check_dcd(motg);
1262 tmout = ++motg->dcd_retries == MSM_CHG_DCD_MAX_RETRIES;
1263 if (is_dcd || tmout) {
1264 msm_chg_disable_dcd(motg);
1265 msm_chg_enable_primary_det(motg);
1266 delay = MSM_CHG_PRIMARY_DET_TIME;
1267 motg->chg_state = USB_CHG_STATE_DCD_DONE;
1268 } else {
1269 delay = MSM_CHG_DCD_POLL_TIME;
1270 }
1271 break;
1272 case USB_CHG_STATE_DCD_DONE:
1273 vout = msm_chg_check_primary_det(motg);
1274 if (vout) {
1275 msm_chg_enable_secondary_det(motg);
1276 delay = MSM_CHG_SECONDARY_DET_TIME;
1277 motg->chg_state = USB_CHG_STATE_PRIMARY_DONE;
1278 } else {
1279 motg->chg_type = USB_SDP_CHARGER;
1280 motg->chg_state = USB_CHG_STATE_DETECTED;
1281 delay = 0;
1282 }
1283 break;
1284 case USB_CHG_STATE_PRIMARY_DONE:
1285 vout = msm_chg_check_secondary_det(motg);
1286 if (vout)
1287 motg->chg_type = USB_DCP_CHARGER;
1288 else
1289 motg->chg_type = USB_CDP_CHARGER;
1290 motg->chg_state = USB_CHG_STATE_SECONDARY_DONE;
1291 /* fall through */
1292 case USB_CHG_STATE_SECONDARY_DONE:
1293 motg->chg_state = USB_CHG_STATE_DETECTED;
1294 case USB_CHG_STATE_DETECTED:
1295 msm_chg_block_off(motg);
1296 dev_dbg(phy->dev, "charger = %d\n", motg->chg_type);
1297 schedule_work(&motg->sm_work);
1298 return;
1299 default:
1300 return;
1301 }
1302
1303 schedule_delayed_work(&motg->chg_work, delay);
1304}
1305
1306/*
1307 * We support OTG, Peripheral only and Host only configurations. In case
1308 * of OTG, mode switch (host-->peripheral/peripheral-->host) can happen
1309 * via Id pin status or user request (debugfs). Id/BSV interrupts are not
1310 * enabled when switch is controlled by user and default mode is supplied
1311 * by board file, which can be changed by userspace later.
1312 */
1313static void msm_otg_init_sm(struct msm_otg *motg)
1314{
1315 struct msm_otg_platform_data *pdata = motg->pdata;
1316 u32 otgsc = readl(USB_OTGSC);
1317
1318 switch (pdata->mode) {
1319 case USB_DR_MODE_OTG:
1320 if (pdata->otg_control == OTG_PHY_CONTROL) {
1321 if (otgsc & OTGSC_ID)
1322 set_bit(ID, &motg->inputs);
1323 else
1324 clear_bit(ID, &motg->inputs);
1325
1326 if (otgsc & OTGSC_BSV)
1327 set_bit(B_SESS_VLD, &motg->inputs);
1328 else
1329 clear_bit(B_SESS_VLD, &motg->inputs);
1330 } else if (pdata->otg_control == OTG_USER_CONTROL) {
1331 set_bit(ID, &motg->inputs);
1332 clear_bit(B_SESS_VLD, &motg->inputs);
1333 }
1334 break;
1335 case USB_DR_MODE_HOST:
1336 clear_bit(ID, &motg->inputs);
1337 break;
1338 case USB_DR_MODE_PERIPHERAL:
1339 set_bit(ID, &motg->inputs);
1340 if (otgsc & OTGSC_BSV)
1341 set_bit(B_SESS_VLD, &motg->inputs);
1342 else
1343 clear_bit(B_SESS_VLD, &motg->inputs);
1344 break;
1345 default:
1346 break;
1347 }
1348}
1349
1350static void msm_otg_sm_work(struct work_struct *w)
1351{
1352 struct msm_otg *motg = container_of(w, struct msm_otg, sm_work);
1353 struct usb_otg *otg = motg->phy.otg;
1354
1355 switch (otg->state) {
1356 case OTG_STATE_UNDEFINED:
1357 dev_dbg(otg->usb_phy->dev, "OTG_STATE_UNDEFINED state\n");
1358 msm_otg_reset(otg->usb_phy);
1359 msm_otg_init_sm(motg);
1360 otg->state = OTG_STATE_B_IDLE;
1361 /* FALL THROUGH */
1362 case OTG_STATE_B_IDLE:
1363 dev_dbg(otg->usb_phy->dev, "OTG_STATE_B_IDLE state\n");
1364 if (!test_bit(ID, &motg->inputs) && otg->host) {
1365 /* disable BSV bit */
1366 writel(readl(USB_OTGSC) & ~OTGSC_BSVIE, USB_OTGSC);
1367 msm_otg_start_host(otg->usb_phy, 1);
1368 otg->state = OTG_STATE_A_HOST;
1369 } else if (test_bit(B_SESS_VLD, &motg->inputs)) {
1370 switch (motg->chg_state) {
1371 case USB_CHG_STATE_UNDEFINED:
1372 msm_chg_detect_work(&motg->chg_work.work);
1373 break;
1374 case USB_CHG_STATE_DETECTED:
1375 switch (motg->chg_type) {
1376 case USB_DCP_CHARGER:
1377 msm_otg_notify_charger(motg,
1378 IDEV_CHG_MAX);
1379 break;
1380 case USB_CDP_CHARGER:
1381 msm_otg_notify_charger(motg,
1382 IDEV_CHG_MAX);
1383 msm_otg_start_peripheral(otg->usb_phy,
1384 1);
1385 otg->state
1386 = OTG_STATE_B_PERIPHERAL;
1387 break;
1388 case USB_SDP_CHARGER:
1389 msm_otg_notify_charger(motg, IUNIT);
1390 msm_otg_start_peripheral(otg->usb_phy,
1391 1);
1392 otg->state
1393 = OTG_STATE_B_PERIPHERAL;
1394 break;
1395 default:
1396 break;
1397 }
1398 break;
1399 default:
1400 break;
1401 }
1402 } else {
1403 /*
1404 * If charger detection work is pending, decrement
1405 * the pm usage counter to balance with the one that
1406 * is incremented in charger detection work.
1407 */
1408 if (cancel_delayed_work_sync(&motg->chg_work)) {
1409 pm_runtime_put_sync(otg->usb_phy->dev);
1410 msm_otg_reset(otg->usb_phy);
1411 }
1412 msm_otg_notify_charger(motg, 0);
1413 motg->chg_state = USB_CHG_STATE_UNDEFINED;
1414 motg->chg_type = USB_INVALID_CHARGER;
1415 }
1416
1417 if (otg->state == OTG_STATE_B_IDLE)
1418 pm_runtime_put_sync(otg->usb_phy->dev);
1419 break;
1420 case OTG_STATE_B_PERIPHERAL:
1421 dev_dbg(otg->usb_phy->dev, "OTG_STATE_B_PERIPHERAL state\n");
1422 if (!test_bit(B_SESS_VLD, &motg->inputs) ||
1423 !test_bit(ID, &motg->inputs)) {
1424 msm_otg_notify_charger(motg, 0);
1425 msm_otg_start_peripheral(otg->usb_phy, 0);
1426 motg->chg_state = USB_CHG_STATE_UNDEFINED;
1427 motg->chg_type = USB_INVALID_CHARGER;
1428 otg->state = OTG_STATE_B_IDLE;
1429 msm_otg_reset(otg->usb_phy);
1430 schedule_work(w);
1431 }
1432 break;
1433 case OTG_STATE_A_HOST:
1434 dev_dbg(otg->usb_phy->dev, "OTG_STATE_A_HOST state\n");
1435 if (test_bit(ID, &motg->inputs)) {
1436 msm_otg_start_host(otg->usb_phy, 0);
1437 otg->state = OTG_STATE_B_IDLE;
1438 msm_otg_reset(otg->usb_phy);
1439 schedule_work(w);
1440 }
1441 break;
1442 default:
1443 break;
1444 }
1445}
1446
1447static irqreturn_t msm_otg_irq(int irq, void *data)
1448{
1449 struct msm_otg *motg = data;
1450 struct usb_phy *phy = &motg->phy;
1451 u32 otgsc = 0;
1452
1453 if (atomic_read(&motg->in_lpm)) {
1454 disable_irq_nosync(irq);
1455 motg->async_int = 1;
1456 pm_runtime_get(phy->dev);
1457 return IRQ_HANDLED;
1458 }
1459
1460 otgsc = readl(USB_OTGSC);
1461 if (!(otgsc & (OTGSC_IDIS | OTGSC_BSVIS)))
1462 return IRQ_NONE;
1463
1464 if ((otgsc & OTGSC_IDIS) && (otgsc & OTGSC_IDIE)) {
1465 if (otgsc & OTGSC_ID)
1466 set_bit(ID, &motg->inputs);
1467 else
1468 clear_bit(ID, &motg->inputs);
1469 dev_dbg(phy->dev, "ID set/clear\n");
1470 pm_runtime_get_noresume(phy->dev);
1471 } else if ((otgsc & OTGSC_BSVIS) && (otgsc & OTGSC_BSVIE)) {
1472 if (otgsc & OTGSC_BSV)
1473 set_bit(B_SESS_VLD, &motg->inputs);
1474 else
1475 clear_bit(B_SESS_VLD, &motg->inputs);
1476 dev_dbg(phy->dev, "BSV set/clear\n");
1477 pm_runtime_get_noresume(phy->dev);
1478 }
1479
1480 writel(otgsc, USB_OTGSC);
1481 schedule_work(&motg->sm_work);
1482 return IRQ_HANDLED;
1483}
1484
1485static int msm_otg_mode_show(struct seq_file *s, void *unused)
1486{
1487 struct msm_otg *motg = s->private;
1488 struct usb_otg *otg = motg->phy.otg;
1489
1490 switch (otg->state) {
1491 case OTG_STATE_A_HOST:
1492 seq_puts(s, "host\n");
1493 break;
1494 case OTG_STATE_B_PERIPHERAL:
1495 seq_puts(s, "peripheral\n");
1496 break;
1497 default:
1498 seq_puts(s, "none\n");
1499 break;
1500 }
1501
1502 return 0;
1503}
1504
1505static int msm_otg_mode_open(struct inode *inode, struct file *file)
1506{
1507 return single_open(file, msm_otg_mode_show, inode->i_private);
1508}
1509
1510static ssize_t msm_otg_mode_write(struct file *file, const char __user *ubuf,
1511 size_t count, loff_t *ppos)
1512{
1513 struct seq_file *s = file->private_data;
1514 struct msm_otg *motg = s->private;
1515 char buf[16];
1516 struct usb_otg *otg = motg->phy.otg;
1517 int status = count;
1518 enum usb_dr_mode req_mode;
1519
1520 memset(buf, 0x00, sizeof(buf));
1521
1522 if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count))) {
1523 status = -EFAULT;
1524 goto out;
1525 }
1526
1527 if (!strncmp(buf, "host", 4)) {
1528 req_mode = USB_DR_MODE_HOST;
1529 } else if (!strncmp(buf, "peripheral", 10)) {
1530 req_mode = USB_DR_MODE_PERIPHERAL;
1531 } else if (!strncmp(buf, "none", 4)) {
1532 req_mode = USB_DR_MODE_UNKNOWN;
1533 } else {
1534 status = -EINVAL;
1535 goto out;
1536 }
1537
1538 switch (req_mode) {
1539 case USB_DR_MODE_UNKNOWN:
1540 switch (otg->state) {
1541 case OTG_STATE_A_HOST:
1542 case OTG_STATE_B_PERIPHERAL:
1543 set_bit(ID, &motg->inputs);
1544 clear_bit(B_SESS_VLD, &motg->inputs);
1545 break;
1546 default:
1547 goto out;
1548 }
1549 break;
1550 case USB_DR_MODE_PERIPHERAL:
1551 switch (otg->state) {
1552 case OTG_STATE_B_IDLE:
1553 case OTG_STATE_A_HOST:
1554 set_bit(ID, &motg->inputs);
1555 set_bit(B_SESS_VLD, &motg->inputs);
1556 break;
1557 default:
1558 goto out;
1559 }
1560 break;
1561 case USB_DR_MODE_HOST:
1562 switch (otg->state) {
1563 case OTG_STATE_B_IDLE:
1564 case OTG_STATE_B_PERIPHERAL:
1565 clear_bit(ID, &motg->inputs);
1566 break;
1567 default:
1568 goto out;
1569 }
1570 break;
1571 default:
1572 goto out;
1573 }
1574
1575 pm_runtime_get_sync(otg->usb_phy->dev);
1576 schedule_work(&motg->sm_work);
1577out:
1578 return status;
1579}
1580
1581static const struct file_operations msm_otg_mode_fops = {
1582 .open = msm_otg_mode_open,
1583 .read = seq_read,
1584 .write = msm_otg_mode_write,
1585 .llseek = seq_lseek,
1586 .release = single_release,
1587};
1588
1589static struct dentry *msm_otg_dbg_root;
1590static struct dentry *msm_otg_dbg_mode;
1591
1592static int msm_otg_debugfs_init(struct msm_otg *motg)
1593{
1594 msm_otg_dbg_root = debugfs_create_dir("msm_otg", NULL);
1595
1596 if (!msm_otg_dbg_root || IS_ERR(msm_otg_dbg_root))
1597 return -ENODEV;
1598
1599 msm_otg_dbg_mode = debugfs_create_file("mode", S_IRUGO | S_IWUSR,
1600 msm_otg_dbg_root, motg, &msm_otg_mode_fops);
1601 if (!msm_otg_dbg_mode) {
1602 debugfs_remove(msm_otg_dbg_root);
1603 msm_otg_dbg_root = NULL;
1604 return -ENODEV;
1605 }
1606
1607 return 0;
1608}
1609
1610static void msm_otg_debugfs_cleanup(void)
1611{
1612 debugfs_remove(msm_otg_dbg_mode);
1613 debugfs_remove(msm_otg_dbg_root);
1614}
1615
1616static const struct of_device_id msm_otg_dt_match[] = {
1617 {
1618 .compatible = "qcom,usb-otg-ci",
1619 .data = (void *) CI_45NM_INTEGRATED_PHY
1620 },
1621 {
1622 .compatible = "qcom,usb-otg-snps",
1623 .data = (void *) SNPS_28NM_INTEGRATED_PHY
1624 },
1625 { }
1626};
1627MODULE_DEVICE_TABLE(of, msm_otg_dt_match);
1628
1629static int msm_otg_vbus_notifier(struct notifier_block *nb, unsigned long event,
1630 void *ptr)
1631{
1632 struct msm_usb_cable *vbus = container_of(nb, struct msm_usb_cable, nb);
1633 struct msm_otg *motg = container_of(vbus, struct msm_otg, vbus);
1634
1635 if (event)
1636 set_bit(B_SESS_VLD, &motg->inputs);
1637 else
1638 clear_bit(B_SESS_VLD, &motg->inputs);
1639
1640 if (test_bit(B_SESS_VLD, &motg->inputs)) {
1641 /* Switch D+/D- lines to Device connector */
1642 gpiod_set_value_cansleep(motg->switch_gpio, 0);
1643 } else {
1644 /* Switch D+/D- lines to Hub */
1645 gpiod_set_value_cansleep(motg->switch_gpio, 1);
1646 }
1647
1648 schedule_work(&motg->sm_work);
1649
1650 return NOTIFY_DONE;
1651}
1652
1653static int msm_otg_id_notifier(struct notifier_block *nb, unsigned long event,
1654 void *ptr)
1655{
1656 struct msm_usb_cable *id = container_of(nb, struct msm_usb_cable, nb);
1657 struct msm_otg *motg = container_of(id, struct msm_otg, id);
1658
1659 if (event)
1660 clear_bit(ID, &motg->inputs);
1661 else
1662 set_bit(ID, &motg->inputs);
1663
1664 schedule_work(&motg->sm_work);
1665
1666 return NOTIFY_DONE;
1667}
1668
1669static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg)
1670{
1671 struct msm_otg_platform_data *pdata;
1672 struct extcon_dev *ext_id, *ext_vbus;
1673 struct device_node *node = pdev->dev.of_node;
1674 struct property *prop;
1675 int len, ret, words;
1676 u32 val, tmp[3];
1677
1678 pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
1679 if (!pdata)
1680 return -ENOMEM;
1681
1682 motg->pdata = pdata;
1683
1684 pdata->phy_type = (enum msm_usb_phy_type)of_device_get_match_data(&pdev->dev);
1685 if (!pdata->phy_type)
1686 return 1;
1687
1688 motg->link_rst = devm_reset_control_get(&pdev->dev, "link");
1689 if (IS_ERR(motg->link_rst))
1690 return PTR_ERR(motg->link_rst);
1691
1692 motg->phy_rst = devm_reset_control_get(&pdev->dev, "phy");
1693 if (IS_ERR(motg->phy_rst))
1694 motg->phy_rst = NULL;
1695
1696 pdata->mode = usb_get_dr_mode(&pdev->dev);
1697 if (pdata->mode == USB_DR_MODE_UNKNOWN)
1698 pdata->mode = USB_DR_MODE_OTG;
1699
1700 pdata->otg_control = OTG_PHY_CONTROL;
1701 if (!of_property_read_u32(node, "qcom,otg-control", &val))
1702 if (val == OTG_PMIC_CONTROL)
1703 pdata->otg_control = val;
1704
1705 if (!of_property_read_u32(node, "qcom,phy-num", &val) && val < 2)
1706 motg->phy_number = val;
1707
1708 motg->vdd_levels[VDD_LEVEL_NONE] = USB_PHY_SUSP_DIG_VOL;
1709 motg->vdd_levels[VDD_LEVEL_MIN] = USB_PHY_VDD_DIG_VOL_MIN;
1710 motg->vdd_levels[VDD_LEVEL_MAX] = USB_PHY_VDD_DIG_VOL_MAX;
1711
1712 if (of_get_property(node, "qcom,vdd-levels", &len) &&
1713 len == sizeof(tmp)) {
1714 of_property_read_u32_array(node, "qcom,vdd-levels",
1715 tmp, len / sizeof(*tmp));
1716 motg->vdd_levels[VDD_LEVEL_NONE] = tmp[VDD_LEVEL_NONE];
1717 motg->vdd_levels[VDD_LEVEL_MIN] = tmp[VDD_LEVEL_MIN];
1718 motg->vdd_levels[VDD_LEVEL_MAX] = tmp[VDD_LEVEL_MAX];
1719 }
1720
1721 motg->manual_pullup = of_property_read_bool(node, "qcom,manual-pullup");
1722
1723 motg->switch_gpio = devm_gpiod_get_optional(&pdev->dev, "switch",
1724 GPIOD_OUT_LOW);
1725 if (IS_ERR(motg->switch_gpio))
1726 return PTR_ERR(motg->switch_gpio);
1727
1728 ext_id = ERR_PTR(-ENODEV);
1729 ext_vbus = ERR_PTR(-ENODEV);
1730 if (of_property_read_bool(node, "extcon")) {
1731
1732 /* Each one of them is not mandatory */
1733 ext_vbus = extcon_get_edev_by_phandle(&pdev->dev, 0);
1734 if (IS_ERR(ext_vbus) && PTR_ERR(ext_vbus) != -ENODEV)
1735 return PTR_ERR(ext_vbus);
1736
1737 ext_id = extcon_get_edev_by_phandle(&pdev->dev, 1);
1738 if (IS_ERR(ext_id) && PTR_ERR(ext_id) != -ENODEV)
1739 return PTR_ERR(ext_id);
1740 }
1741
1742 if (!IS_ERR(ext_vbus)) {
1743 motg->vbus.extcon = ext_vbus;
1744 motg->vbus.nb.notifier_call = msm_otg_vbus_notifier;
1745 ret = extcon_register_notifier(ext_vbus, EXTCON_USB,
1746 &motg->vbus.nb);
1747 if (ret < 0) {
1748 dev_err(&pdev->dev, "register VBUS notifier failed\n");
1749 return ret;
1750 }
1751
1752 ret = extcon_get_cable_state_(ext_vbus, EXTCON_USB);
1753 if (ret)
1754 set_bit(B_SESS_VLD, &motg->inputs);
1755 else
1756 clear_bit(B_SESS_VLD, &motg->inputs);
1757 }
1758
1759 if (!IS_ERR(ext_id)) {
1760 motg->id.extcon = ext_id;
1761 motg->id.nb.notifier_call = msm_otg_id_notifier;
1762 ret = extcon_register_notifier(ext_id, EXTCON_USB_HOST,
1763 &motg->id.nb);
1764 if (ret < 0) {
1765 dev_err(&pdev->dev, "register ID notifier failed\n");
1766 extcon_unregister_notifier(motg->vbus.extcon,
1767 EXTCON_USB, &motg->vbus.nb);
1768 return ret;
1769 }
1770
1771 ret = extcon_get_cable_state_(ext_id, EXTCON_USB_HOST);
1772 if (ret)
1773 clear_bit(ID, &motg->inputs);
1774 else
1775 set_bit(ID, &motg->inputs);
1776 }
1777
1778 prop = of_find_property(node, "qcom,phy-init-sequence", &len);
1779 if (!prop || !len)
1780 return 0;
1781
1782 words = len / sizeof(u32);
1783
1784 if (words >= ULPI_EXT_VENDOR_SPECIFIC) {
1785 dev_warn(&pdev->dev, "Too big PHY init sequence %d\n", words);
1786 return 0;
1787 }
1788
1789 pdata->phy_init_seq = devm_kzalloc(&pdev->dev, len, GFP_KERNEL);
1790 if (!pdata->phy_init_seq)
1791 return 0;
1792
1793 ret = of_property_read_u32_array(node, "qcom,phy-init-sequence",
1794 pdata->phy_init_seq, words);
1795 if (!ret)
1796 pdata->phy_init_sz = words;
1797
1798 return 0;
1799}
1800
1801static int msm_otg_reboot_notify(struct notifier_block *this,
1802 unsigned long code, void *unused)
1803{
1804 struct msm_otg *motg = container_of(this, struct msm_otg, reboot);
1805
1806 /*
1807 * Ensure that D+/D- lines are routed to uB connector, so
1808 * we could load bootloader/kernel at next reboot
1809 */
1810 gpiod_set_value_cansleep(motg->switch_gpio, 0);
1811 return NOTIFY_DONE;
1812}
1813
1814static int msm_otg_probe(struct platform_device *pdev)
1815{
1816 struct regulator_bulk_data regs[3];
1817 int ret = 0;
1818 struct device_node *np = pdev->dev.of_node;
1819 struct msm_otg_platform_data *pdata;
1820 struct resource *res;
1821 struct msm_otg *motg;
1822 struct usb_phy *phy;
1823 void __iomem *phy_select;
1824
1825 motg = devm_kzalloc(&pdev->dev, sizeof(struct msm_otg), GFP_KERNEL);
1826 if (!motg)
1827 return -ENOMEM;
1828
1829 motg->phy.otg = devm_kzalloc(&pdev->dev, sizeof(struct usb_otg),
1830 GFP_KERNEL);
1831 if (!motg->phy.otg)
1832 return -ENOMEM;
1833
1834 phy = &motg->phy;
1835 phy->dev = &pdev->dev;
1836
1837 motg->clk = devm_clk_get(&pdev->dev, np ? "core" : "usb_hs_clk");
1838 if (IS_ERR(motg->clk)) {
1839 dev_err(&pdev->dev, "failed to get usb_hs_clk\n");
1840 return PTR_ERR(motg->clk);
1841 }
1842
1843 /*
1844 * If USB Core is running its protocol engine based on CORE CLK,
1845 * CORE CLK must be running at >55Mhz for correct HSUSB
1846 * operation and USB core cannot tolerate frequency changes on
1847 * CORE CLK.
1848 */
1849 motg->pclk = devm_clk_get(&pdev->dev, np ? "iface" : "usb_hs_pclk");
1850 if (IS_ERR(motg->pclk)) {
1851 dev_err(&pdev->dev, "failed to get usb_hs_pclk\n");
1852 return PTR_ERR(motg->pclk);
1853 }
1854
1855 /*
1856 * USB core clock is not present on all MSM chips. This
1857 * clock is introduced to remove the dependency on AXI
1858 * bus frequency.
1859 */
1860 motg->core_clk = devm_clk_get(&pdev->dev,
1861 np ? "alt_core" : "usb_hs_core_clk");
1862
1863 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1864 if (!res)
1865 return -EINVAL;
1866 motg->regs = devm_ioremap(&pdev->dev, res->start, resource_size(res));
1867 if (!motg->regs)
1868 return -ENOMEM;
1869
1870 pdata = dev_get_platdata(&pdev->dev);
1871 if (!pdata) {
1872 if (!np)
1873 return -ENXIO;
1874 ret = msm_otg_read_dt(pdev, motg);
1875 if (ret)
1876 return ret;
1877 }
1878
1879 /*
1880 * NOTE: The PHYs can be multiplexed between the chipidea controller
1881 * and the dwc3 controller, using a single bit. It is important that
1882 * the dwc3 driver does not set this bit in an incompatible way.
1883 */
1884 if (motg->phy_number) {
1885 phy_select = devm_ioremap_nocache(&pdev->dev, USB2_PHY_SEL, 4);
1886 if (!phy_select) {
1887 ret = -ENOMEM;
1888 goto unregister_extcon;
1889 }
1890 /* Enable second PHY with the OTG port */
1891 writel(0x1, phy_select);
1892 }
1893
1894 dev_info(&pdev->dev, "OTG regs = %p\n", motg->regs);
1895
1896 motg->irq = platform_get_irq(pdev, 0);
1897 if (motg->irq < 0) {
1898 dev_err(&pdev->dev, "platform_get_irq failed\n");
1899 ret = motg->irq;
1900 goto unregister_extcon;
1901 }
1902
1903 regs[0].supply = "vddcx";
1904 regs[1].supply = "v3p3";
1905 regs[2].supply = "v1p8";
1906
1907 ret = devm_regulator_bulk_get(motg->phy.dev, ARRAY_SIZE(regs), regs);
1908 if (ret)
1909 goto unregister_extcon;
1910
1911 motg->vddcx = regs[0].consumer;
1912 motg->v3p3 = regs[1].consumer;
1913 motg->v1p8 = regs[2].consumer;
1914
1915 clk_set_rate(motg->clk, 60000000);
1916
1917 clk_prepare_enable(motg->clk);
1918 clk_prepare_enable(motg->pclk);
1919
1920 if (!IS_ERR(motg->core_clk))
1921 clk_prepare_enable(motg->core_clk);
1922
1923 ret = msm_hsusb_init_vddcx(motg, 1);
1924 if (ret) {
1925 dev_err(&pdev->dev, "hsusb vddcx configuration failed\n");
1926 goto disable_clks;
1927 }
1928
1929 ret = msm_hsusb_ldo_init(motg, 1);
1930 if (ret) {
1931 dev_err(&pdev->dev, "hsusb vreg configuration failed\n");
1932 goto disable_vddcx;
1933 }
1934 ret = msm_hsusb_ldo_set_mode(motg, 1);
1935 if (ret) {
1936 dev_err(&pdev->dev, "hsusb vreg enable failed\n");
1937 goto disable_ldo;
1938 }
1939
1940 writel(0, USB_USBINTR);
1941 writel(0, USB_OTGSC);
1942
1943 INIT_WORK(&motg->sm_work, msm_otg_sm_work);
1944 INIT_DELAYED_WORK(&motg->chg_work, msm_chg_detect_work);
1945 ret = devm_request_irq(&pdev->dev, motg->irq, msm_otg_irq, IRQF_SHARED,
1946 "msm_otg", motg);
1947 if (ret) {
1948 dev_err(&pdev->dev, "request irq failed\n");
1949 goto disable_ldo;
1950 }
1951
1952 phy->init = msm_phy_init;
1953 phy->set_power = msm_otg_set_power;
1954 phy->notify_disconnect = msm_phy_notify_disconnect;
1955 phy->type = USB_PHY_TYPE_USB2;
1956
1957 phy->io_ops = &msm_otg_io_ops;
1958
1959 phy->otg->usb_phy = &motg->phy;
1960 phy->otg->set_host = msm_otg_set_host;
1961 phy->otg->set_peripheral = msm_otg_set_peripheral;
1962
1963 msm_usb_reset(phy);
1964
1965 ret = usb_add_phy_dev(&motg->phy);
1966 if (ret) {
1967 dev_err(&pdev->dev, "usb_add_phy failed\n");
1968 goto disable_ldo;
1969 }
1970
1971 platform_set_drvdata(pdev, motg);
1972 device_init_wakeup(&pdev->dev, 1);
1973
1974 if (motg->pdata->mode == USB_DR_MODE_OTG &&
1975 motg->pdata->otg_control == OTG_USER_CONTROL) {
1976 ret = msm_otg_debugfs_init(motg);
1977 if (ret)
1978 dev_dbg(&pdev->dev, "Can not create mode change file\n");
1979 }
1980
1981 if (test_bit(B_SESS_VLD, &motg->inputs)) {
1982 /* Switch D+/D- lines to Device connector */
1983 gpiod_set_value_cansleep(motg->switch_gpio, 0);
1984 } else {
1985 /* Switch D+/D- lines to Hub */
1986 gpiod_set_value_cansleep(motg->switch_gpio, 1);
1987 }
1988
1989 motg->reboot.notifier_call = msm_otg_reboot_notify;
1990 register_reboot_notifier(&motg->reboot);
1991
1992 pm_runtime_set_active(&pdev->dev);
1993 pm_runtime_enable(&pdev->dev);
1994
1995 return 0;
1996
1997disable_ldo:
1998 msm_hsusb_ldo_init(motg, 0);
1999disable_vddcx:
2000 msm_hsusb_init_vddcx(motg, 0);
2001disable_clks:
2002 clk_disable_unprepare(motg->pclk);
2003 clk_disable_unprepare(motg->clk);
2004 if (!IS_ERR(motg->core_clk))
2005 clk_disable_unprepare(motg->core_clk);
2006unregister_extcon:
2007 extcon_unregister_notifier(motg->id.extcon,
2008 EXTCON_USB_HOST, &motg->id.nb);
2009 extcon_unregister_notifier(motg->vbus.extcon,
2010 EXTCON_USB, &motg->vbus.nb);
2011
2012 return ret;
2013}
2014
2015static int msm_otg_remove(struct platform_device *pdev)
2016{
2017 struct msm_otg *motg = platform_get_drvdata(pdev);
2018 struct usb_phy *phy = &motg->phy;
2019 int cnt = 0;
2020
2021 if (phy->otg->host || phy->otg->gadget)
2022 return -EBUSY;
2023
2024 unregister_reboot_notifier(&motg->reboot);
2025
2026 /*
2027 * Ensure that D+/D- lines are routed to uB connector, so
2028 * we could load bootloader/kernel at next reboot
2029 */
2030 gpiod_set_value_cansleep(motg->switch_gpio, 0);
2031
2032 extcon_unregister_notifier(motg->id.extcon, EXTCON_USB_HOST, &motg->id.nb);
2033 extcon_unregister_notifier(motg->vbus.extcon, EXTCON_USB, &motg->vbus.nb);
2034
2035 msm_otg_debugfs_cleanup();
2036 cancel_delayed_work_sync(&motg->chg_work);
2037 cancel_work_sync(&motg->sm_work);
2038
2039 pm_runtime_resume(&pdev->dev);
2040
2041 device_init_wakeup(&pdev->dev, 0);
2042 pm_runtime_disable(&pdev->dev);
2043
2044 usb_remove_phy(phy);
2045 disable_irq(motg->irq);
2046
2047 /*
2048 * Put PHY in low power mode.
2049 */
2050 ulpi_read(phy, 0x14);
2051 ulpi_write(phy, 0x08, 0x09);
2052
2053 writel(readl(USB_PORTSC) | PORTSC_PHCD, USB_PORTSC);
2054 while (cnt < PHY_SUSPEND_TIMEOUT_USEC) {
2055 if (readl(USB_PORTSC) & PORTSC_PHCD)
2056 break;
2057 udelay(1);
2058 cnt++;
2059 }
2060 if (cnt >= PHY_SUSPEND_TIMEOUT_USEC)
2061 dev_err(phy->dev, "Unable to suspend PHY\n");
2062
2063 clk_disable_unprepare(motg->pclk);
2064 clk_disable_unprepare(motg->clk);
2065 if (!IS_ERR(motg->core_clk))
2066 clk_disable_unprepare(motg->core_clk);
2067 msm_hsusb_ldo_init(motg, 0);
2068
2069 pm_runtime_set_suspended(&pdev->dev);
2070
2071 return 0;
2072}
2073
2074#ifdef CONFIG_PM
2075static int msm_otg_runtime_idle(struct device *dev)
2076{
2077 struct msm_otg *motg = dev_get_drvdata(dev);
2078 struct usb_otg *otg = motg->phy.otg;
2079
2080 dev_dbg(dev, "OTG runtime idle\n");
2081
2082 /*
2083 * It is observed some times that a spurious interrupt
2084 * comes when PHY is put into LPM immediately after PHY reset.
2085 * This 1 sec delay also prevents entering into LPM immediately
2086 * after asynchronous interrupt.
2087 */
2088 if (otg->state != OTG_STATE_UNDEFINED)
2089 pm_schedule_suspend(dev, 1000);
2090
2091 return -EAGAIN;
2092}
2093
2094static int msm_otg_runtime_suspend(struct device *dev)
2095{
2096 struct msm_otg *motg = dev_get_drvdata(dev);
2097
2098 dev_dbg(dev, "OTG runtime suspend\n");
2099 return msm_otg_suspend(motg);
2100}
2101
2102static int msm_otg_runtime_resume(struct device *dev)
2103{
2104 struct msm_otg *motg = dev_get_drvdata(dev);
2105
2106 dev_dbg(dev, "OTG runtime resume\n");
2107 return msm_otg_resume(motg);
2108}
2109#endif
2110
2111#ifdef CONFIG_PM_SLEEP
2112static int msm_otg_pm_suspend(struct device *dev)
2113{
2114 struct msm_otg *motg = dev_get_drvdata(dev);
2115
2116 dev_dbg(dev, "OTG PM suspend\n");
2117 return msm_otg_suspend(motg);
2118}
2119
2120static int msm_otg_pm_resume(struct device *dev)
2121{
2122 struct msm_otg *motg = dev_get_drvdata(dev);
2123 int ret;
2124
2125 dev_dbg(dev, "OTG PM resume\n");
2126
2127 ret = msm_otg_resume(motg);
2128 if (ret)
2129 return ret;
2130
2131 /*
2132 * Runtime PM Documentation recommends bringing the
2133 * device to full powered state upon resume.
2134 */
2135 pm_runtime_disable(dev);
2136 pm_runtime_set_active(dev);
2137 pm_runtime_enable(dev);
2138
2139 return 0;
2140}
2141#endif
2142
2143static const struct dev_pm_ops msm_otg_dev_pm_ops = {
2144 SET_SYSTEM_SLEEP_PM_OPS(msm_otg_pm_suspend, msm_otg_pm_resume)
2145 SET_RUNTIME_PM_OPS(msm_otg_runtime_suspend, msm_otg_runtime_resume,
2146 msm_otg_runtime_idle)
2147};
2148
2149static struct platform_driver msm_otg_driver = {
2150 .probe = msm_otg_probe,
2151 .remove = msm_otg_remove,
2152 .driver = {
2153 .name = DRIVER_NAME,
2154 .pm = &msm_otg_dev_pm_ops,
2155 .of_match_table = msm_otg_dt_match,
2156 },
2157};
2158
2159module_platform_driver(msm_otg_driver);
2160
2161MODULE_LICENSE("GPL v2");
2162MODULE_DESCRIPTION("MSM USB transceiver driver");