Loading...
1/*
2 * SPI_PPC4XX SPI controller driver.
3 *
4 * Copyright (C) 2007 Gary Jennejohn <garyj@denx.de>
5 * Copyright 2008 Stefan Roese <sr@denx.de>, DENX Software Engineering
6 * Copyright 2009 Harris Corporation, Steven A. Falco <sfalco@harris.com>
7 *
8 * Based in part on drivers/spi/spi_s3c24xx.c
9 *
10 * Copyright (c) 2006 Ben Dooks
11 * Copyright (c) 2006 Simtec Electronics
12 * Ben Dooks <ben@simtec.co.uk>
13 *
14 * This program is free software; you can redistribute it and/or modify it
15 * under the terms of the GNU General Public License version 2 as published
16 * by the Free Software Foundation.
17 */
18
19/*
20 * The PPC4xx SPI controller has no FIFO so each sent/received byte will
21 * generate an interrupt to the CPU. This can cause high CPU utilization.
22 * This driver allows platforms to reduce the interrupt load on the CPU
23 * during SPI transfers by setting max_speed_hz via the device tree.
24 */
25
26#include <linux/module.h>
27#include <linux/sched.h>
28#include <linux/slab.h>
29#include <linux/errno.h>
30#include <linux/wait.h>
31#include <linux/of_address.h>
32#include <linux/of_irq.h>
33#include <linux/of_platform.h>
34#include <linux/of_gpio.h>
35#include <linux/interrupt.h>
36#include <linux/delay.h>
37
38#include <linux/gpio.h>
39#include <linux/spi/spi.h>
40#include <linux/spi/spi_bitbang.h>
41
42#include <asm/io.h>
43#include <asm/dcr.h>
44#include <asm/dcr-regs.h>
45
46/* bits in mode register - bit 0 is MSb */
47
48/*
49 * SPI_PPC4XX_MODE_SCP = 0 means "data latched on trailing edge of clock"
50 * SPI_PPC4XX_MODE_SCP = 1 means "data latched on leading edge of clock"
51 * Note: This is the inverse of CPHA.
52 */
53#define SPI_PPC4XX_MODE_SCP (0x80 >> 3)
54
55/* SPI_PPC4XX_MODE_SPE = 1 means "port enabled" */
56#define SPI_PPC4XX_MODE_SPE (0x80 >> 4)
57
58/*
59 * SPI_PPC4XX_MODE_RD = 0 means "MSB first" - this is the normal mode
60 * SPI_PPC4XX_MODE_RD = 1 means "LSB first" - this is bit-reversed mode
61 * Note: This is identical to SPI_LSB_FIRST.
62 */
63#define SPI_PPC4XX_MODE_RD (0x80 >> 5)
64
65/*
66 * SPI_PPC4XX_MODE_CI = 0 means "clock idles low"
67 * SPI_PPC4XX_MODE_CI = 1 means "clock idles high"
68 * Note: This is identical to CPOL.
69 */
70#define SPI_PPC4XX_MODE_CI (0x80 >> 6)
71
72/*
73 * SPI_PPC4XX_MODE_IL = 0 means "loopback disable"
74 * SPI_PPC4XX_MODE_IL = 1 means "loopback enable"
75 */
76#define SPI_PPC4XX_MODE_IL (0x80 >> 7)
77
78/* bits in control register */
79/* starts a transfer when set */
80#define SPI_PPC4XX_CR_STR (0x80 >> 7)
81
82/* bits in status register */
83/* port is busy with a transfer */
84#define SPI_PPC4XX_SR_BSY (0x80 >> 6)
85/* RxD ready */
86#define SPI_PPC4XX_SR_RBR (0x80 >> 7)
87
88/* clock settings (SCP and CI) for various SPI modes */
89#define SPI_CLK_MODE0 (SPI_PPC4XX_MODE_SCP | 0)
90#define SPI_CLK_MODE1 (0 | 0)
91#define SPI_CLK_MODE2 (SPI_PPC4XX_MODE_SCP | SPI_PPC4XX_MODE_CI)
92#define SPI_CLK_MODE3 (0 | SPI_PPC4XX_MODE_CI)
93
94#define DRIVER_NAME "spi_ppc4xx_of"
95
96struct spi_ppc4xx_regs {
97 u8 mode;
98 u8 rxd;
99 u8 txd;
100 u8 cr;
101 u8 sr;
102 u8 dummy;
103 /*
104 * Clock divisor modulus register
105 * This uses the following formula:
106 * SCPClkOut = OPBCLK/(4(CDM + 1))
107 * or
108 * CDM = (OPBCLK/4*SCPClkOut) - 1
109 * bit 0 is the MSb!
110 */
111 u8 cdm;
112};
113
114/* SPI Controller driver's private data. */
115struct ppc4xx_spi {
116 /* bitbang has to be first */
117 struct spi_bitbang bitbang;
118 struct completion done;
119
120 u64 mapbase;
121 u64 mapsize;
122 int irqnum;
123 /* need this to set the SPI clock */
124 unsigned int opb_freq;
125
126 /* for transfers */
127 int len;
128 int count;
129 /* data buffers */
130 const unsigned char *tx;
131 unsigned char *rx;
132
133 int *gpios;
134
135 struct spi_ppc4xx_regs __iomem *regs; /* pointer to the registers */
136 struct spi_master *master;
137 struct device *dev;
138};
139
140/* need this so we can set the clock in the chipselect routine */
141struct spi_ppc4xx_cs {
142 u8 mode;
143};
144
145static int spi_ppc4xx_txrx(struct spi_device *spi, struct spi_transfer *t)
146{
147 struct ppc4xx_spi *hw;
148 u8 data;
149
150 dev_dbg(&spi->dev, "txrx: tx %p, rx %p, len %d\n",
151 t->tx_buf, t->rx_buf, t->len);
152
153 hw = spi_master_get_devdata(spi->master);
154
155 hw->tx = t->tx_buf;
156 hw->rx = t->rx_buf;
157 hw->len = t->len;
158 hw->count = 0;
159
160 /* send the first byte */
161 data = hw->tx ? hw->tx[0] : 0;
162 out_8(&hw->regs->txd, data);
163 out_8(&hw->regs->cr, SPI_PPC4XX_CR_STR);
164 wait_for_completion(&hw->done);
165
166 return hw->count;
167}
168
169static int spi_ppc4xx_setupxfer(struct spi_device *spi, struct spi_transfer *t)
170{
171 struct ppc4xx_spi *hw = spi_master_get_devdata(spi->master);
172 struct spi_ppc4xx_cs *cs = spi->controller_state;
173 int scr;
174 u8 cdm = 0;
175 u32 speed;
176 u8 bits_per_word;
177
178 /* Start with the generic configuration for this device. */
179 bits_per_word = spi->bits_per_word;
180 speed = spi->max_speed_hz;
181
182 /*
183 * Modify the configuration if the transfer overrides it. Do not allow
184 * the transfer to overwrite the generic configuration with zeros.
185 */
186 if (t) {
187 if (t->bits_per_word)
188 bits_per_word = t->bits_per_word;
189
190 if (t->speed_hz)
191 speed = min(t->speed_hz, spi->max_speed_hz);
192 }
193
194 if (!speed || (speed > spi->max_speed_hz)) {
195 dev_err(&spi->dev, "invalid speed_hz (%d)\n", speed);
196 return -EINVAL;
197 }
198
199 /* Write new configuration */
200 out_8(&hw->regs->mode, cs->mode);
201
202 /* Set the clock */
203 /* opb_freq was already divided by 4 */
204 scr = (hw->opb_freq / speed) - 1;
205 if (scr > 0)
206 cdm = min(scr, 0xff);
207
208 dev_dbg(&spi->dev, "setting pre-scaler to %d (hz %d)\n", cdm, speed);
209
210 if (in_8(&hw->regs->cdm) != cdm)
211 out_8(&hw->regs->cdm, cdm);
212
213 mutex_lock(&hw->bitbang.lock);
214 if (!hw->bitbang.busy) {
215 hw->bitbang.chipselect(spi, BITBANG_CS_INACTIVE);
216 /* Need to ndelay here? */
217 }
218 mutex_unlock(&hw->bitbang.lock);
219
220 return 0;
221}
222
223static int spi_ppc4xx_setup(struct spi_device *spi)
224{
225 struct spi_ppc4xx_cs *cs = spi->controller_state;
226
227 if (!spi->max_speed_hz) {
228 dev_err(&spi->dev, "invalid max_speed_hz (must be non-zero)\n");
229 return -EINVAL;
230 }
231
232 if (cs == NULL) {
233 cs = kzalloc(sizeof *cs, GFP_KERNEL);
234 if (!cs)
235 return -ENOMEM;
236 spi->controller_state = cs;
237 }
238
239 /*
240 * We set all bits of the SPI0_MODE register, so,
241 * no need to read-modify-write
242 */
243 cs->mode = SPI_PPC4XX_MODE_SPE;
244
245 switch (spi->mode & (SPI_CPHA | SPI_CPOL)) {
246 case SPI_MODE_0:
247 cs->mode |= SPI_CLK_MODE0;
248 break;
249 case SPI_MODE_1:
250 cs->mode |= SPI_CLK_MODE1;
251 break;
252 case SPI_MODE_2:
253 cs->mode |= SPI_CLK_MODE2;
254 break;
255 case SPI_MODE_3:
256 cs->mode |= SPI_CLK_MODE3;
257 break;
258 }
259
260 if (spi->mode & SPI_LSB_FIRST)
261 cs->mode |= SPI_PPC4XX_MODE_RD;
262
263 return 0;
264}
265
266static void spi_ppc4xx_chipsel(struct spi_device *spi, int value)
267{
268 struct ppc4xx_spi *hw = spi_master_get_devdata(spi->master);
269 unsigned int cs = spi->chip_select;
270 unsigned int cspol;
271
272 /*
273 * If there are no chip selects at all, or if this is the special
274 * case of a non-existent (dummy) chip select, do nothing.
275 */
276
277 if (!hw->master->num_chipselect || hw->gpios[cs] == -EEXIST)
278 return;
279
280 cspol = spi->mode & SPI_CS_HIGH ? 1 : 0;
281 if (value == BITBANG_CS_INACTIVE)
282 cspol = !cspol;
283
284 gpio_set_value(hw->gpios[cs], cspol);
285}
286
287static irqreturn_t spi_ppc4xx_int(int irq, void *dev_id)
288{
289 struct ppc4xx_spi *hw;
290 u8 status;
291 u8 data;
292 unsigned int count;
293
294 hw = (struct ppc4xx_spi *)dev_id;
295
296 status = in_8(&hw->regs->sr);
297 if (!status)
298 return IRQ_NONE;
299
300 /*
301 * BSY de-asserts one cycle after the transfer is complete. The
302 * interrupt is asserted after the transfer is complete. The exact
303 * relationship is not documented, hence this code.
304 */
305
306 if (unlikely(status & SPI_PPC4XX_SR_BSY)) {
307 u8 lstatus;
308 int cnt = 0;
309
310 dev_dbg(hw->dev, "got interrupt but spi still busy?\n");
311 do {
312 ndelay(10);
313 lstatus = in_8(&hw->regs->sr);
314 } while (++cnt < 100 && lstatus & SPI_PPC4XX_SR_BSY);
315
316 if (cnt >= 100) {
317 dev_err(hw->dev, "busywait: too many loops!\n");
318 complete(&hw->done);
319 return IRQ_HANDLED;
320 } else {
321 /* status is always 1 (RBR) here */
322 status = in_8(&hw->regs->sr);
323 dev_dbg(hw->dev, "loops %d status %x\n", cnt, status);
324 }
325 }
326
327 count = hw->count;
328 hw->count++;
329
330 /* RBR triggered this interrupt. Therefore, data must be ready. */
331 data = in_8(&hw->regs->rxd);
332 if (hw->rx)
333 hw->rx[count] = data;
334
335 count++;
336
337 if (count < hw->len) {
338 data = hw->tx ? hw->tx[count] : 0;
339 out_8(&hw->regs->txd, data);
340 out_8(&hw->regs->cr, SPI_PPC4XX_CR_STR);
341 } else {
342 complete(&hw->done);
343 }
344
345 return IRQ_HANDLED;
346}
347
348static void spi_ppc4xx_cleanup(struct spi_device *spi)
349{
350 kfree(spi->controller_state);
351}
352
353static void spi_ppc4xx_enable(struct ppc4xx_spi *hw)
354{
355 /*
356 * On all 4xx PPC's the SPI bus is shared/multiplexed with
357 * the 2nd I2C bus. We need to enable the the SPI bus before
358 * using it.
359 */
360
361 /* need to clear bit 14 to enable SPC */
362 dcri_clrset(SDR0, SDR0_PFC1, 0x80000000 >> 14, 0);
363}
364
365static void free_gpios(struct ppc4xx_spi *hw)
366{
367 if (hw->master->num_chipselect) {
368 int i;
369 for (i = 0; i < hw->master->num_chipselect; i++)
370 if (gpio_is_valid(hw->gpios[i]))
371 gpio_free(hw->gpios[i]);
372
373 kfree(hw->gpios);
374 hw->gpios = NULL;
375 }
376}
377
378/*
379 * platform_device layer stuff...
380 */
381static int spi_ppc4xx_of_probe(struct platform_device *op)
382{
383 struct ppc4xx_spi *hw;
384 struct spi_master *master;
385 struct spi_bitbang *bbp;
386 struct resource resource;
387 struct device_node *np = op->dev.of_node;
388 struct device *dev = &op->dev;
389 struct device_node *opbnp;
390 int ret;
391 int num_gpios;
392 const unsigned int *clk;
393
394 master = spi_alloc_master(dev, sizeof *hw);
395 if (master == NULL)
396 return -ENOMEM;
397 master->dev.of_node = np;
398 platform_set_drvdata(op, master);
399 hw = spi_master_get_devdata(master);
400 hw->master = master;
401 hw->dev = dev;
402
403 init_completion(&hw->done);
404
405 /*
406 * A count of zero implies a single SPI device without any chip-select.
407 * Note that of_gpio_count counts all gpios assigned to this spi master.
408 * This includes both "null" gpio's and real ones.
409 */
410 num_gpios = of_gpio_count(np);
411 if (num_gpios > 0) {
412 int i;
413
414 hw->gpios = kzalloc(sizeof(int) * num_gpios, GFP_KERNEL);
415 if (!hw->gpios) {
416 ret = -ENOMEM;
417 goto free_master;
418 }
419
420 for (i = 0; i < num_gpios; i++) {
421 int gpio;
422 enum of_gpio_flags flags;
423
424 gpio = of_get_gpio_flags(np, i, &flags);
425 hw->gpios[i] = gpio;
426
427 if (gpio_is_valid(gpio)) {
428 /* Real CS - set the initial state. */
429 ret = gpio_request(gpio, np->name);
430 if (ret < 0) {
431 dev_err(dev, "can't request gpio "
432 "#%d: %d\n", i, ret);
433 goto free_gpios;
434 }
435
436 gpio_direction_output(gpio,
437 !!(flags & OF_GPIO_ACTIVE_LOW));
438 } else if (gpio == -EEXIST) {
439 ; /* No CS, but that's OK. */
440 } else {
441 dev_err(dev, "invalid gpio #%d: %d\n", i, gpio);
442 ret = -EINVAL;
443 goto free_gpios;
444 }
445 }
446 }
447
448 /* Setup the state for the bitbang driver */
449 bbp = &hw->bitbang;
450 bbp->master = hw->master;
451 bbp->setup_transfer = spi_ppc4xx_setupxfer;
452 bbp->chipselect = spi_ppc4xx_chipsel;
453 bbp->txrx_bufs = spi_ppc4xx_txrx;
454 bbp->use_dma = 0;
455 bbp->master->setup = spi_ppc4xx_setup;
456 bbp->master->cleanup = spi_ppc4xx_cleanup;
457 bbp->master->bits_per_word_mask = SPI_BPW_MASK(8);
458
459 /* the spi->mode bits understood by this driver: */
460 bbp->master->mode_bits =
461 SPI_CPHA | SPI_CPOL | SPI_CS_HIGH | SPI_LSB_FIRST;
462
463 /* this many pins in all GPIO controllers */
464 bbp->master->num_chipselect = num_gpios > 0 ? num_gpios : 0;
465
466 /* Get the clock for the OPB */
467 opbnp = of_find_compatible_node(NULL, NULL, "ibm,opb");
468 if (opbnp == NULL) {
469 dev_err(dev, "OPB: cannot find node\n");
470 ret = -ENODEV;
471 goto free_gpios;
472 }
473 /* Get the clock (Hz) for the OPB */
474 clk = of_get_property(opbnp, "clock-frequency", NULL);
475 if (clk == NULL) {
476 dev_err(dev, "OPB: no clock-frequency property set\n");
477 of_node_put(opbnp);
478 ret = -ENODEV;
479 goto free_gpios;
480 }
481 hw->opb_freq = *clk;
482 hw->opb_freq >>= 2;
483 of_node_put(opbnp);
484
485 ret = of_address_to_resource(np, 0, &resource);
486 if (ret) {
487 dev_err(dev, "error while parsing device node resource\n");
488 goto free_gpios;
489 }
490 hw->mapbase = resource.start;
491 hw->mapsize = resource_size(&resource);
492
493 /* Sanity check */
494 if (hw->mapsize < sizeof(struct spi_ppc4xx_regs)) {
495 dev_err(dev, "too small to map registers\n");
496 ret = -EINVAL;
497 goto free_gpios;
498 }
499
500 /* Request IRQ */
501 hw->irqnum = irq_of_parse_and_map(np, 0);
502 ret = request_irq(hw->irqnum, spi_ppc4xx_int,
503 0, "spi_ppc4xx_of", (void *)hw);
504 if (ret) {
505 dev_err(dev, "unable to allocate interrupt\n");
506 goto free_gpios;
507 }
508
509 if (!request_mem_region(hw->mapbase, hw->mapsize, DRIVER_NAME)) {
510 dev_err(dev, "resource unavailable\n");
511 ret = -EBUSY;
512 goto request_mem_error;
513 }
514
515 hw->regs = ioremap(hw->mapbase, sizeof(struct spi_ppc4xx_regs));
516
517 if (!hw->regs) {
518 dev_err(dev, "unable to memory map registers\n");
519 ret = -ENXIO;
520 goto map_io_error;
521 }
522
523 spi_ppc4xx_enable(hw);
524
525 /* Finally register our spi controller */
526 dev->dma_mask = 0;
527 ret = spi_bitbang_start(bbp);
528 if (ret) {
529 dev_err(dev, "failed to register SPI master\n");
530 goto unmap_regs;
531 }
532
533 dev_info(dev, "driver initialized\n");
534
535 return 0;
536
537unmap_regs:
538 iounmap(hw->regs);
539map_io_error:
540 release_mem_region(hw->mapbase, hw->mapsize);
541request_mem_error:
542 free_irq(hw->irqnum, hw);
543free_gpios:
544 free_gpios(hw);
545free_master:
546 spi_master_put(master);
547
548 dev_err(dev, "initialization failed\n");
549 return ret;
550}
551
552static int spi_ppc4xx_of_remove(struct platform_device *op)
553{
554 struct spi_master *master = platform_get_drvdata(op);
555 struct ppc4xx_spi *hw = spi_master_get_devdata(master);
556
557 spi_bitbang_stop(&hw->bitbang);
558 release_mem_region(hw->mapbase, hw->mapsize);
559 free_irq(hw->irqnum, hw);
560 iounmap(hw->regs);
561 free_gpios(hw);
562 spi_master_put(master);
563 return 0;
564}
565
566static const struct of_device_id spi_ppc4xx_of_match[] = {
567 { .compatible = "ibm,ppc4xx-spi", },
568 {},
569};
570
571MODULE_DEVICE_TABLE(of, spi_ppc4xx_of_match);
572
573static struct platform_driver spi_ppc4xx_of_driver = {
574 .probe = spi_ppc4xx_of_probe,
575 .remove = spi_ppc4xx_of_remove,
576 .driver = {
577 .name = DRIVER_NAME,
578 .of_match_table = spi_ppc4xx_of_match,
579 },
580};
581module_platform_driver(spi_ppc4xx_of_driver);
582
583MODULE_AUTHOR("Gary Jennejohn & Stefan Roese");
584MODULE_DESCRIPTION("Simple PPC4xx SPI Driver");
585MODULE_LICENSE("GPL");
1/*
2 * SPI_PPC4XX SPI controller driver.
3 *
4 * Copyright (C) 2007 Gary Jennejohn <garyj@denx.de>
5 * Copyright 2008 Stefan Roese <sr@denx.de>, DENX Software Engineering
6 * Copyright 2009 Harris Corporation, Steven A. Falco <sfalco@harris.com>
7 *
8 * Based in part on drivers/spi/spi_s3c24xx.c
9 *
10 * Copyright (c) 2006 Ben Dooks
11 * Copyright (c) 2006 Simtec Electronics
12 * Ben Dooks <ben@simtec.co.uk>
13 *
14 * This program is free software; you can redistribute it and/or modify it
15 * under the terms of the GNU General Public License version 2 as published
16 * by the Free Software Foundation.
17 */
18
19/*
20 * The PPC4xx SPI controller has no FIFO so each sent/received byte will
21 * generate an interrupt to the CPU. This can cause high CPU utilization.
22 * This driver allows platforms to reduce the interrupt load on the CPU
23 * during SPI transfers by setting max_speed_hz via the device tree.
24 */
25
26#include <linux/module.h>
27#include <linux/init.h>
28#include <linux/sched.h>
29#include <linux/slab.h>
30#include <linux/errno.h>
31#include <linux/wait.h>
32#include <linux/of_platform.h>
33#include <linux/of_gpio.h>
34#include <linux/interrupt.h>
35#include <linux/delay.h>
36
37#include <linux/gpio.h>
38#include <linux/spi/spi.h>
39#include <linux/spi/spi_bitbang.h>
40
41#include <asm/io.h>
42#include <asm/dcr.h>
43#include <asm/dcr-regs.h>
44
45/* bits in mode register - bit 0 is MSb */
46
47/*
48 * SPI_PPC4XX_MODE_SCP = 0 means "data latched on trailing edge of clock"
49 * SPI_PPC4XX_MODE_SCP = 1 means "data latched on leading edge of clock"
50 * Note: This is the inverse of CPHA.
51 */
52#define SPI_PPC4XX_MODE_SCP (0x80 >> 3)
53
54/* SPI_PPC4XX_MODE_SPE = 1 means "port enabled" */
55#define SPI_PPC4XX_MODE_SPE (0x80 >> 4)
56
57/*
58 * SPI_PPC4XX_MODE_RD = 0 means "MSB first" - this is the normal mode
59 * SPI_PPC4XX_MODE_RD = 1 means "LSB first" - this is bit-reversed mode
60 * Note: This is identical to SPI_LSB_FIRST.
61 */
62#define SPI_PPC4XX_MODE_RD (0x80 >> 5)
63
64/*
65 * SPI_PPC4XX_MODE_CI = 0 means "clock idles low"
66 * SPI_PPC4XX_MODE_CI = 1 means "clock idles high"
67 * Note: This is identical to CPOL.
68 */
69#define SPI_PPC4XX_MODE_CI (0x80 >> 6)
70
71/*
72 * SPI_PPC4XX_MODE_IL = 0 means "loopback disable"
73 * SPI_PPC4XX_MODE_IL = 1 means "loopback enable"
74 */
75#define SPI_PPC4XX_MODE_IL (0x80 >> 7)
76
77/* bits in control register */
78/* starts a transfer when set */
79#define SPI_PPC4XX_CR_STR (0x80 >> 7)
80
81/* bits in status register */
82/* port is busy with a transfer */
83#define SPI_PPC4XX_SR_BSY (0x80 >> 6)
84/* RxD ready */
85#define SPI_PPC4XX_SR_RBR (0x80 >> 7)
86
87/* clock settings (SCP and CI) for various SPI modes */
88#define SPI_CLK_MODE0 (SPI_PPC4XX_MODE_SCP | 0)
89#define SPI_CLK_MODE1 (0 | 0)
90#define SPI_CLK_MODE2 (SPI_PPC4XX_MODE_SCP | SPI_PPC4XX_MODE_CI)
91#define SPI_CLK_MODE3 (0 | SPI_PPC4XX_MODE_CI)
92
93#define DRIVER_NAME "spi_ppc4xx_of"
94
95struct spi_ppc4xx_regs {
96 u8 mode;
97 u8 rxd;
98 u8 txd;
99 u8 cr;
100 u8 sr;
101 u8 dummy;
102 /*
103 * Clock divisor modulus register
104 * This uses the follwing formula:
105 * SCPClkOut = OPBCLK/(4(CDM + 1))
106 * or
107 * CDM = (OPBCLK/4*SCPClkOut) - 1
108 * bit 0 is the MSb!
109 */
110 u8 cdm;
111};
112
113/* SPI Controller driver's private data. */
114struct ppc4xx_spi {
115 /* bitbang has to be first */
116 struct spi_bitbang bitbang;
117 struct completion done;
118
119 u64 mapbase;
120 u64 mapsize;
121 int irqnum;
122 /* need this to set the SPI clock */
123 unsigned int opb_freq;
124
125 /* for transfers */
126 int len;
127 int count;
128 /* data buffers */
129 const unsigned char *tx;
130 unsigned char *rx;
131
132 int *gpios;
133
134 struct spi_ppc4xx_regs __iomem *regs; /* pointer to the registers */
135 struct spi_master *master;
136 struct device *dev;
137};
138
139/* need this so we can set the clock in the chipselect routine */
140struct spi_ppc4xx_cs {
141 u8 mode;
142};
143
144static int spi_ppc4xx_txrx(struct spi_device *spi, struct spi_transfer *t)
145{
146 struct ppc4xx_spi *hw;
147 u8 data;
148
149 dev_dbg(&spi->dev, "txrx: tx %p, rx %p, len %d\n",
150 t->tx_buf, t->rx_buf, t->len);
151
152 hw = spi_master_get_devdata(spi->master);
153
154 hw->tx = t->tx_buf;
155 hw->rx = t->rx_buf;
156 hw->len = t->len;
157 hw->count = 0;
158
159 /* send the first byte */
160 data = hw->tx ? hw->tx[0] : 0;
161 out_8(&hw->regs->txd, data);
162 out_8(&hw->regs->cr, SPI_PPC4XX_CR_STR);
163 wait_for_completion(&hw->done);
164
165 return hw->count;
166}
167
168static int spi_ppc4xx_setupxfer(struct spi_device *spi, struct spi_transfer *t)
169{
170 struct ppc4xx_spi *hw = spi_master_get_devdata(spi->master);
171 struct spi_ppc4xx_cs *cs = spi->controller_state;
172 int scr;
173 u8 cdm = 0;
174 u32 speed;
175 u8 bits_per_word;
176
177 /* Start with the generic configuration for this device. */
178 bits_per_word = spi->bits_per_word;
179 speed = spi->max_speed_hz;
180
181 /*
182 * Modify the configuration if the transfer overrides it. Do not allow
183 * the transfer to overwrite the generic configuration with zeros.
184 */
185 if (t) {
186 if (t->bits_per_word)
187 bits_per_word = t->bits_per_word;
188
189 if (t->speed_hz)
190 speed = min(t->speed_hz, spi->max_speed_hz);
191 }
192
193 if (bits_per_word != 8) {
194 dev_err(&spi->dev, "invalid bits-per-word (%d)\n",
195 bits_per_word);
196 return -EINVAL;
197 }
198
199 if (!speed || (speed > spi->max_speed_hz)) {
200 dev_err(&spi->dev, "invalid speed_hz (%d)\n", speed);
201 return -EINVAL;
202 }
203
204 /* Write new configration */
205 out_8(&hw->regs->mode, cs->mode);
206
207 /* Set the clock */
208 /* opb_freq was already divided by 4 */
209 scr = (hw->opb_freq / speed) - 1;
210 if (scr > 0)
211 cdm = min(scr, 0xff);
212
213 dev_dbg(&spi->dev, "setting pre-scaler to %d (hz %d)\n", cdm, speed);
214
215 if (in_8(&hw->regs->cdm) != cdm)
216 out_8(&hw->regs->cdm, cdm);
217
218 spin_lock(&hw->bitbang.lock);
219 if (!hw->bitbang.busy) {
220 hw->bitbang.chipselect(spi, BITBANG_CS_INACTIVE);
221 /* Need to ndelay here? */
222 }
223 spin_unlock(&hw->bitbang.lock);
224
225 return 0;
226}
227
228static int spi_ppc4xx_setup(struct spi_device *spi)
229{
230 struct spi_ppc4xx_cs *cs = spi->controller_state;
231
232 if (spi->bits_per_word != 8) {
233 dev_err(&spi->dev, "invalid bits-per-word (%d)\n",
234 spi->bits_per_word);
235 return -EINVAL;
236 }
237
238 if (!spi->max_speed_hz) {
239 dev_err(&spi->dev, "invalid max_speed_hz (must be non-zero)\n");
240 return -EINVAL;
241 }
242
243 if (cs == NULL) {
244 cs = kzalloc(sizeof *cs, GFP_KERNEL);
245 if (!cs)
246 return -ENOMEM;
247 spi->controller_state = cs;
248 }
249
250 /*
251 * We set all bits of the SPI0_MODE register, so,
252 * no need to read-modify-write
253 */
254 cs->mode = SPI_PPC4XX_MODE_SPE;
255
256 switch (spi->mode & (SPI_CPHA | SPI_CPOL)) {
257 case SPI_MODE_0:
258 cs->mode |= SPI_CLK_MODE0;
259 break;
260 case SPI_MODE_1:
261 cs->mode |= SPI_CLK_MODE1;
262 break;
263 case SPI_MODE_2:
264 cs->mode |= SPI_CLK_MODE2;
265 break;
266 case SPI_MODE_3:
267 cs->mode |= SPI_CLK_MODE3;
268 break;
269 }
270
271 if (spi->mode & SPI_LSB_FIRST)
272 cs->mode |= SPI_PPC4XX_MODE_RD;
273
274 return 0;
275}
276
277static void spi_ppc4xx_chipsel(struct spi_device *spi, int value)
278{
279 struct ppc4xx_spi *hw = spi_master_get_devdata(spi->master);
280 unsigned int cs = spi->chip_select;
281 unsigned int cspol;
282
283 /*
284 * If there are no chip selects at all, or if this is the special
285 * case of a non-existent (dummy) chip select, do nothing.
286 */
287
288 if (!hw->master->num_chipselect || hw->gpios[cs] == -EEXIST)
289 return;
290
291 cspol = spi->mode & SPI_CS_HIGH ? 1 : 0;
292 if (value == BITBANG_CS_INACTIVE)
293 cspol = !cspol;
294
295 gpio_set_value(hw->gpios[cs], cspol);
296}
297
298static irqreturn_t spi_ppc4xx_int(int irq, void *dev_id)
299{
300 struct ppc4xx_spi *hw;
301 u8 status;
302 u8 data;
303 unsigned int count;
304
305 hw = (struct ppc4xx_spi *)dev_id;
306
307 status = in_8(&hw->regs->sr);
308 if (!status)
309 return IRQ_NONE;
310
311 /*
312 * BSY de-asserts one cycle after the transfer is complete. The
313 * interrupt is asserted after the transfer is complete. The exact
314 * relationship is not documented, hence this code.
315 */
316
317 if (unlikely(status & SPI_PPC4XX_SR_BSY)) {
318 u8 lstatus;
319 int cnt = 0;
320
321 dev_dbg(hw->dev, "got interrupt but spi still busy?\n");
322 do {
323 ndelay(10);
324 lstatus = in_8(&hw->regs->sr);
325 } while (++cnt < 100 && lstatus & SPI_PPC4XX_SR_BSY);
326
327 if (cnt >= 100) {
328 dev_err(hw->dev, "busywait: too many loops!\n");
329 complete(&hw->done);
330 return IRQ_HANDLED;
331 } else {
332 /* status is always 1 (RBR) here */
333 status = in_8(&hw->regs->sr);
334 dev_dbg(hw->dev, "loops %d status %x\n", cnt, status);
335 }
336 }
337
338 count = hw->count;
339 hw->count++;
340
341 /* RBR triggered this interrupt. Therefore, data must be ready. */
342 data = in_8(&hw->regs->rxd);
343 if (hw->rx)
344 hw->rx[count] = data;
345
346 count++;
347
348 if (count < hw->len) {
349 data = hw->tx ? hw->tx[count] : 0;
350 out_8(&hw->regs->txd, data);
351 out_8(&hw->regs->cr, SPI_PPC4XX_CR_STR);
352 } else {
353 complete(&hw->done);
354 }
355
356 return IRQ_HANDLED;
357}
358
359static void spi_ppc4xx_cleanup(struct spi_device *spi)
360{
361 kfree(spi->controller_state);
362}
363
364static void spi_ppc4xx_enable(struct ppc4xx_spi *hw)
365{
366 /*
367 * On all 4xx PPC's the SPI bus is shared/multiplexed with
368 * the 2nd I2C bus. We need to enable the the SPI bus before
369 * using it.
370 */
371
372 /* need to clear bit 14 to enable SPC */
373 dcri_clrset(SDR0, SDR0_PFC1, 0x80000000 >> 14, 0);
374}
375
376static void free_gpios(struct ppc4xx_spi *hw)
377{
378 if (hw->master->num_chipselect) {
379 int i;
380 for (i = 0; i < hw->master->num_chipselect; i++)
381 if (gpio_is_valid(hw->gpios[i]))
382 gpio_free(hw->gpios[i]);
383
384 kfree(hw->gpios);
385 hw->gpios = NULL;
386 }
387}
388
389/*
390 * platform_device layer stuff...
391 */
392static int __init spi_ppc4xx_of_probe(struct platform_device *op)
393{
394 struct ppc4xx_spi *hw;
395 struct spi_master *master;
396 struct spi_bitbang *bbp;
397 struct resource resource;
398 struct device_node *np = op->dev.of_node;
399 struct device *dev = &op->dev;
400 struct device_node *opbnp;
401 int ret;
402 int num_gpios;
403 const unsigned int *clk;
404
405 master = spi_alloc_master(dev, sizeof *hw);
406 if (master == NULL)
407 return -ENOMEM;
408 master->dev.of_node = np;
409 dev_set_drvdata(dev, master);
410 hw = spi_master_get_devdata(master);
411 hw->master = spi_master_get(master);
412 hw->dev = dev;
413
414 init_completion(&hw->done);
415
416 /*
417 * A count of zero implies a single SPI device without any chip-select.
418 * Note that of_gpio_count counts all gpios assigned to this spi master.
419 * This includes both "null" gpio's and real ones.
420 */
421 num_gpios = of_gpio_count(np);
422 if (num_gpios) {
423 int i;
424
425 hw->gpios = kzalloc(sizeof(int) * num_gpios, GFP_KERNEL);
426 if (!hw->gpios) {
427 ret = -ENOMEM;
428 goto free_master;
429 }
430
431 for (i = 0; i < num_gpios; i++) {
432 int gpio;
433 enum of_gpio_flags flags;
434
435 gpio = of_get_gpio_flags(np, i, &flags);
436 hw->gpios[i] = gpio;
437
438 if (gpio_is_valid(gpio)) {
439 /* Real CS - set the initial state. */
440 ret = gpio_request(gpio, np->name);
441 if (ret < 0) {
442 dev_err(dev, "can't request gpio "
443 "#%d: %d\n", i, ret);
444 goto free_gpios;
445 }
446
447 gpio_direction_output(gpio,
448 !!(flags & OF_GPIO_ACTIVE_LOW));
449 } else if (gpio == -EEXIST) {
450 ; /* No CS, but that's OK. */
451 } else {
452 dev_err(dev, "invalid gpio #%d: %d\n", i, gpio);
453 ret = -EINVAL;
454 goto free_gpios;
455 }
456 }
457 }
458
459 /* Setup the state for the bitbang driver */
460 bbp = &hw->bitbang;
461 bbp->master = hw->master;
462 bbp->setup_transfer = spi_ppc4xx_setupxfer;
463 bbp->chipselect = spi_ppc4xx_chipsel;
464 bbp->txrx_bufs = spi_ppc4xx_txrx;
465 bbp->use_dma = 0;
466 bbp->master->setup = spi_ppc4xx_setup;
467 bbp->master->cleanup = spi_ppc4xx_cleanup;
468
469 /* the spi->mode bits understood by this driver: */
470 bbp->master->mode_bits =
471 SPI_CPHA | SPI_CPOL | SPI_CS_HIGH | SPI_LSB_FIRST;
472
473 /* this many pins in all GPIO controllers */
474 bbp->master->num_chipselect = num_gpios;
475
476 /* Get the clock for the OPB */
477 opbnp = of_find_compatible_node(NULL, NULL, "ibm,opb");
478 if (opbnp == NULL) {
479 dev_err(dev, "OPB: cannot find node\n");
480 ret = -ENODEV;
481 goto free_gpios;
482 }
483 /* Get the clock (Hz) for the OPB */
484 clk = of_get_property(opbnp, "clock-frequency", NULL);
485 if (clk == NULL) {
486 dev_err(dev, "OPB: no clock-frequency property set\n");
487 of_node_put(opbnp);
488 ret = -ENODEV;
489 goto free_gpios;
490 }
491 hw->opb_freq = *clk;
492 hw->opb_freq >>= 2;
493 of_node_put(opbnp);
494
495 ret = of_address_to_resource(np, 0, &resource);
496 if (ret) {
497 dev_err(dev, "error while parsing device node resource\n");
498 goto free_gpios;
499 }
500 hw->mapbase = resource.start;
501 hw->mapsize = resource_size(&resource);
502
503 /* Sanity check */
504 if (hw->mapsize < sizeof(struct spi_ppc4xx_regs)) {
505 dev_err(dev, "too small to map registers\n");
506 ret = -EINVAL;
507 goto free_gpios;
508 }
509
510 /* Request IRQ */
511 hw->irqnum = irq_of_parse_and_map(np, 0);
512 ret = request_irq(hw->irqnum, spi_ppc4xx_int,
513 0, "spi_ppc4xx_of", (void *)hw);
514 if (ret) {
515 dev_err(dev, "unable to allocate interrupt\n");
516 goto free_gpios;
517 }
518
519 if (!request_mem_region(hw->mapbase, hw->mapsize, DRIVER_NAME)) {
520 dev_err(dev, "resource unavailable\n");
521 ret = -EBUSY;
522 goto request_mem_error;
523 }
524
525 hw->regs = ioremap(hw->mapbase, sizeof(struct spi_ppc4xx_regs));
526
527 if (!hw->regs) {
528 dev_err(dev, "unable to memory map registers\n");
529 ret = -ENXIO;
530 goto map_io_error;
531 }
532
533 spi_ppc4xx_enable(hw);
534
535 /* Finally register our spi controller */
536 dev->dma_mask = 0;
537 ret = spi_bitbang_start(bbp);
538 if (ret) {
539 dev_err(dev, "failed to register SPI master\n");
540 goto unmap_regs;
541 }
542
543 dev_info(dev, "driver initialized\n");
544
545 return 0;
546
547unmap_regs:
548 iounmap(hw->regs);
549map_io_error:
550 release_mem_region(hw->mapbase, hw->mapsize);
551request_mem_error:
552 free_irq(hw->irqnum, hw);
553free_gpios:
554 free_gpios(hw);
555free_master:
556 dev_set_drvdata(dev, NULL);
557 spi_master_put(master);
558
559 dev_err(dev, "initialization failed\n");
560 return ret;
561}
562
563static int __exit spi_ppc4xx_of_remove(struct platform_device *op)
564{
565 struct spi_master *master = dev_get_drvdata(&op->dev);
566 struct ppc4xx_spi *hw = spi_master_get_devdata(master);
567
568 spi_bitbang_stop(&hw->bitbang);
569 dev_set_drvdata(&op->dev, NULL);
570 release_mem_region(hw->mapbase, hw->mapsize);
571 free_irq(hw->irqnum, hw);
572 iounmap(hw->regs);
573 free_gpios(hw);
574 return 0;
575}
576
577static const struct of_device_id spi_ppc4xx_of_match[] = {
578 { .compatible = "ibm,ppc4xx-spi", },
579 {},
580};
581
582MODULE_DEVICE_TABLE(of, spi_ppc4xx_of_match);
583
584static struct platform_driver spi_ppc4xx_of_driver = {
585 .probe = spi_ppc4xx_of_probe,
586 .remove = __exit_p(spi_ppc4xx_of_remove),
587 .driver = {
588 .name = DRIVER_NAME,
589 .owner = THIS_MODULE,
590 .of_match_table = spi_ppc4xx_of_match,
591 },
592};
593module_platform_driver(spi_ppc4xx_of_driver);
594
595MODULE_AUTHOR("Gary Jennejohn & Stefan Roese");
596MODULE_DESCRIPTION("Simple PPC4xx SPI Driver");
597MODULE_LICENSE("GPL");