Loading...
1#
2# Misc strange devices
3#
4
5menu "Misc devices"
6
7config SENSORS_LIS3LV02D
8 tristate
9 depends on INPUT
10 select INPUT_POLLDEV
11 default n
12
13config AD525X_DPOT
14 tristate "Analog Devices Digital Potentiometers"
15 depends on (I2C || SPI) && SYSFS
16 help
17 If you say yes here, you get support for the Analog Devices
18 AD5258, AD5259, AD5251, AD5252, AD5253, AD5254, AD5255
19 AD5160, AD5161, AD5162, AD5165, AD5200, AD5201, AD5203,
20 AD5204, AD5206, AD5207, AD5231, AD5232, AD5233, AD5235,
21 AD5260, AD5262, AD5263, AD5290, AD5291, AD5292, AD5293,
22 AD7376, AD8400, AD8402, AD8403, ADN2850, AD5241, AD5242,
23 AD5243, AD5245, AD5246, AD5247, AD5248, AD5280, AD5282,
24 ADN2860, AD5273, AD5171, AD5170, AD5172, AD5173, AD5270,
25 AD5271, AD5272, AD5274
26 digital potentiometer chips.
27
28 See Documentation/misc-devices/ad525x_dpot.txt for the
29 userspace interface.
30
31 This driver can also be built as a module. If so, the module
32 will be called ad525x_dpot.
33
34config AD525X_DPOT_I2C
35 tristate "support I2C bus connection"
36 depends on AD525X_DPOT && I2C
37 help
38 Say Y here if you have a digital potentiometers hooked to an I2C bus.
39
40 To compile this driver as a module, choose M here: the
41 module will be called ad525x_dpot-i2c.
42
43config AD525X_DPOT_SPI
44 tristate "support SPI bus connection"
45 depends on AD525X_DPOT && SPI_MASTER
46 help
47 Say Y here if you have a digital potentiometers hooked to an SPI bus.
48
49 If unsure, say N (but it's safe to say "Y").
50
51 To compile this driver as a module, choose M here: the
52 module will be called ad525x_dpot-spi.
53
54config ATMEL_TCLIB
55 bool "Atmel AT32/AT91 Timer/Counter Library"
56 depends on (AVR32 || ARCH_AT91)
57 help
58 Select this if you want a library to allocate the Timer/Counter
59 blocks found on many Atmel processors. This facilitates using
60 these blocks by different drivers despite processor differences.
61
62config ATMEL_TCB_CLKSRC
63 bool "TC Block Clocksource"
64 depends on ATMEL_TCLIB
65 default y
66 help
67 Select this to get a high precision clocksource based on a
68 TC block with a 5+ MHz base clock rate. Two timer channels
69 are combined to make a single 32-bit timer.
70
71 When GENERIC_CLOCKEVENTS is defined, the third timer channel
72 may be used as a clock event device supporting oneshot mode
73 (delays of up to two seconds) based on the 32 KiHz clock.
74
75config ATMEL_TCB_CLKSRC_BLOCK
76 int
77 depends on ATMEL_TCB_CLKSRC
78 prompt "TC Block" if CPU_AT32AP700X
79 default 0
80 range 0 1
81 help
82 Some chips provide more than one TC block, so you have the
83 choice of which one to use for the clock framework. The other
84 TC can be used for other purposes, such as PWM generation and
85 interval timing.
86
87config DUMMY_IRQ
88 tristate "Dummy IRQ handler"
89 default n
90 ---help---
91 This module accepts a single 'irq' parameter, which it should register for.
92 The sole purpose of this module is to help with debugging of systems on
93 which spurious IRQs would happen on disabled IRQ vector.
94
95config IBM_ASM
96 tristate "Device driver for IBM RSA service processor"
97 depends on X86 && PCI && INPUT
98 depends on SERIAL_8250 || SERIAL_8250=n
99 ---help---
100 This option enables device driver support for in-band access to the
101 IBM RSA (Condor) service processor in eServer xSeries systems.
102 The ibmasm device driver allows user space application to access
103 ASM (Advanced Systems Management) functions on the service
104 processor. The driver is meant to be used in conjunction with
105 a user space API.
106 The ibmasm driver also enables the OS to use the UART on the
107 service processor board as a regular serial port. To make use of
108 this feature serial driver support (CONFIG_SERIAL_8250) must be
109 enabled.
110
111 WARNING: This software may not be supported or function
112 correctly on your IBM server. Please consult the IBM ServerProven
113 website <http://www-03.ibm.com/systems/info/x86servers/serverproven/compat/us/>
114 for information on the specific driver level and support statement
115 for your IBM server.
116
117config PHANTOM
118 tristate "Sensable PHANToM (PCI)"
119 depends on PCI
120 help
121 Say Y here if you want to build a driver for Sensable PHANToM device.
122
123 This driver is only for PCI PHANToMs.
124
125 If you choose to build module, its name will be phantom. If unsure,
126 say N here.
127
128config INTEL_MID_PTI
129 tristate "Parallel Trace Interface for MIPI P1149.7 cJTAG standard"
130 depends on PCI && TTY && (X86_INTEL_MID || COMPILE_TEST)
131 default n
132 help
133 The PTI (Parallel Trace Interface) driver directs
134 trace data routed from various parts in the system out
135 through an Intel Penwell PTI port and out of the mobile
136 device for analysis with a debugging tool (Lauterbach or Fido).
137
138 You should select this driver if the target kernel is meant for
139 an Intel Atom (non-netbook) mobile device containing a MIPI
140 P1149.7 standard implementation.
141
142config SGI_IOC4
143 tristate "SGI IOC4 Base IO support"
144 depends on PCI
145 ---help---
146 This option enables basic support for the IOC4 chip on certain
147 SGI IO controller cards (IO9, IO10, and PCI-RT). This option
148 does not enable any specific functions on such a card, but provides
149 necessary infrastructure for other drivers to utilize.
150
151 If you have an SGI Altix with an IOC4-based card say Y.
152 Otherwise say N.
153
154config TIFM_CORE
155 tristate "TI Flash Media interface support"
156 depends on PCI
157 help
158 If you want support for Texas Instruments(R) Flash Media adapters
159 you should select this option and then also choose an appropriate
160 host adapter, such as 'TI Flash Media PCI74xx/PCI76xx host adapter
161 support', if you have a TI PCI74xx compatible card reader, for
162 example.
163 You will also have to select some flash card format drivers. MMC/SD
164 cards are supported via 'MMC/SD Card support: TI Flash Media MMC/SD
165 Interface support (MMC_TIFM_SD)'.
166
167 To compile this driver as a module, choose M here: the module will
168 be called tifm_core.
169
170config TIFM_7XX1
171 tristate "TI Flash Media PCI74xx/PCI76xx host adapter support"
172 depends on PCI && TIFM_CORE
173 default TIFM_CORE
174 help
175 This option enables support for Texas Instruments(R) PCI74xx and
176 PCI76xx families of Flash Media adapters, found in many laptops.
177 To make actual use of the device, you will have to select some
178 flash card format drivers, as outlined in the TIFM_CORE Help.
179
180 To compile this driver as a module, choose M here: the module will
181 be called tifm_7xx1.
182
183config ICS932S401
184 tristate "Integrated Circuits ICS932S401"
185 depends on I2C
186 help
187 If you say yes here you get support for the Integrated Circuits
188 ICS932S401 clock control chips.
189
190 This driver can also be built as a module. If so, the module
191 will be called ics932s401.
192
193config ATMEL_SSC
194 tristate "Device driver for Atmel SSC peripheral"
195 depends on HAS_IOMEM && (AVR32 || ARCH_AT91 || COMPILE_TEST)
196 ---help---
197 This option enables device driver support for Atmel Synchronized
198 Serial Communication peripheral (SSC).
199
200 The SSC peripheral supports a wide variety of serial frame based
201 communications, i.e. I2S, SPI, etc.
202
203 If unsure, say N.
204
205config ENCLOSURE_SERVICES
206 tristate "Enclosure Services"
207 default n
208 help
209 Provides support for intelligent enclosures (bays which
210 contain storage devices). You also need either a host
211 driver (SCSI/ATA) which supports enclosures
212 or a SCSI enclosure device (SES) to use these services.
213
214config SGI_XP
215 tristate "Support communication between SGI SSIs"
216 depends on NET
217 depends on (IA64_GENERIC || IA64_SGI_SN2 || IA64_SGI_UV || X86_UV) && SMP
218 select IA64_UNCACHED_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
219 select GENERIC_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
220 select SGI_GRU if X86_64 && SMP
221 ---help---
222 An SGI machine can be divided into multiple Single System
223 Images which act independently of each other and have
224 hardware based memory protection from the others. Enabling
225 this feature will allow for direct communication between SSIs
226 based on a network adapter and DMA messaging.
227
228config CS5535_MFGPT
229 tristate "CS5535/CS5536 Geode Multi-Function General Purpose Timer (MFGPT) support"
230 depends on MFD_CS5535
231 default n
232 help
233 This driver provides access to MFGPT functionality for other
234 drivers that need timers. MFGPTs are available in the CS5535 and
235 CS5536 companion chips that are found in AMD Geode and several
236 other platforms. They have a better resolution and max interval
237 than the generic PIT, and are suitable for use as high-res timers.
238 You probably don't want to enable this manually; other drivers that
239 make use of it should enable it.
240
241config CS5535_MFGPT_DEFAULT_IRQ
242 int
243 depends on CS5535_MFGPT
244 default 7
245 help
246 MFGPTs on the CS5535 require an interrupt. The selected IRQ
247 can be overridden as a module option as well as by driver that
248 use the cs5535_mfgpt_ API; however, different architectures might
249 want to use a different IRQ by default. This is here for
250 architectures to set as necessary.
251
252config CS5535_CLOCK_EVENT_SRC
253 tristate "CS5535/CS5536 high-res timer (MFGPT) events"
254 depends on GENERIC_CLOCKEVENTS && CS5535_MFGPT
255 help
256 This driver provides a clock event source based on the MFGPT
257 timer(s) in the CS5535 and CS5536 companion chips.
258 MFGPTs have a better resolution and max interval than the
259 generic PIT, and are suitable for use as high-res timers.
260
261config HP_ILO
262 tristate "Channel interface driver for the HP iLO processor"
263 depends on PCI
264 default n
265 help
266 The channel interface driver allows applications to communicate
267 with iLO management processors present on HP ProLiant servers.
268 Upon loading, the driver creates /dev/hpilo/dXccbN files, which
269 can be used to gather data from the management processor, via
270 read and write system calls.
271
272 To compile this driver as a module, choose M here: the
273 module will be called hpilo.
274
275config QCOM_COINCELL
276 tristate "Qualcomm coincell charger support"
277 depends on MFD_SPMI_PMIC || COMPILE_TEST
278 help
279 This driver supports the coincell block found inside of
280 Qualcomm PMICs. The coincell charger provides a means to
281 charge a coincell battery or backup capacitor which is used
282 to maintain PMIC register and RTC state in the absence of
283 external power.
284
285config SGI_GRU
286 tristate "SGI GRU driver"
287 depends on X86_UV && SMP
288 default n
289 select MMU_NOTIFIER
290 ---help---
291 The GRU is a hardware resource located in the system chipset. The GRU
292 contains memory that can be mmapped into the user address space. This memory is
293 used to communicate with the GRU to perform functions such as load/store,
294 scatter/gather, bcopy, AMOs, etc. The GRU is directly accessed by user
295 instructions using user virtual addresses. GRU instructions (ex., bcopy) use
296 user virtual addresses for operands.
297
298 If you are not running on a SGI UV system, say N.
299
300config SGI_GRU_DEBUG
301 bool "SGI GRU driver debug"
302 depends on SGI_GRU
303 default n
304 ---help---
305 This option enables additional debugging code for the SGI GRU driver.
306 If you are unsure, say N.
307
308config APDS9802ALS
309 tristate "Medfield Avago APDS9802 ALS Sensor module"
310 depends on I2C
311 help
312 If you say yes here you get support for the ALS APDS9802 ambient
313 light sensor.
314
315 This driver can also be built as a module. If so, the module
316 will be called apds9802als.
317
318config ISL29003
319 tristate "Intersil ISL29003 ambient light sensor"
320 depends on I2C && SYSFS
321 help
322 If you say yes here you get support for the Intersil ISL29003
323 ambient light sensor.
324
325 This driver can also be built as a module. If so, the module
326 will be called isl29003.
327
328config ISL29020
329 tristate "Intersil ISL29020 ambient light sensor"
330 depends on I2C
331 help
332 If you say yes here you get support for the Intersil ISL29020
333 ambient light sensor.
334
335 This driver can also be built as a module. If so, the module
336 will be called isl29020.
337
338config SENSORS_TSL2550
339 tristate "Taos TSL2550 ambient light sensor"
340 depends on I2C && SYSFS
341 help
342 If you say yes here you get support for the Taos TSL2550
343 ambient light sensor.
344
345 This driver can also be built as a module. If so, the module
346 will be called tsl2550.
347
348config SENSORS_BH1780
349 tristate "ROHM BH1780GLI ambient light sensor"
350 depends on I2C && SYSFS
351 help
352 If you say yes here you get support for the ROHM BH1780GLI
353 ambient light sensor.
354
355 This driver can also be built as a module. If so, the module
356 will be called bh1780gli.
357
358config SENSORS_BH1770
359 tristate "BH1770GLC / SFH7770 combined ALS - Proximity sensor"
360 depends on I2C
361 ---help---
362 Say Y here if you want to build a driver for BH1770GLC (ROHM) or
363 SFH7770 (Osram) combined ambient light and proximity sensor chip.
364
365 To compile this driver as a module, choose M here: the
366 module will be called bh1770glc. If unsure, say N here.
367
368config SENSORS_APDS990X
369 tristate "APDS990X combined als and proximity sensors"
370 depends on I2C
371 default n
372 ---help---
373 Say Y here if you want to build a driver for Avago APDS990x
374 combined ambient light and proximity sensor chip.
375
376 To compile this driver as a module, choose M here: the
377 module will be called apds990x. If unsure, say N here.
378
379config HMC6352
380 tristate "Honeywell HMC6352 compass"
381 depends on I2C
382 help
383 This driver provides support for the Honeywell HMC6352 compass,
384 providing configuration and heading data via sysfs.
385
386config DS1682
387 tristate "Dallas DS1682 Total Elapsed Time Recorder with Alarm"
388 depends on I2C
389 help
390 If you say yes here you get support for Dallas Semiconductor
391 DS1682 Total Elapsed Time Recorder.
392
393 This driver can also be built as a module. If so, the module
394 will be called ds1682.
395
396config SPEAR13XX_PCIE_GADGET
397 bool "PCIe gadget support for SPEAr13XX platform"
398 depends on ARCH_SPEAR13XX && BROKEN
399 default n
400 help
401 This option enables gadget support for PCIe controller. If
402 board file defines any controller as PCIe endpoint then a sysfs
403 entry will be created for that controller. User can use these
404 sysfs node to configure PCIe EP as per his requirements.
405
406config TI_DAC7512
407 tristate "Texas Instruments DAC7512"
408 depends on SPI && SYSFS
409 help
410 If you say yes here you get support for the Texas Instruments
411 DAC7512 16-bit digital-to-analog converter.
412
413 This driver can also be built as a module. If so, the module
414 will be called ti_dac7512.
415
416config VMWARE_BALLOON
417 tristate "VMware Balloon Driver"
418 depends on VMWARE_VMCI && X86 && HYPERVISOR_GUEST
419 help
420 This is VMware physical memory management driver which acts
421 like a "balloon" that can be inflated to reclaim physical pages
422 by reserving them in the guest and invalidating them in the
423 monitor, freeing up the underlying machine pages so they can
424 be allocated to other guests. The balloon can also be deflated
425 to allow the guest to use more physical memory.
426
427 If unsure, say N.
428
429 To compile this driver as a module, choose M here: the
430 module will be called vmw_balloon.
431
432config ARM_CHARLCD
433 bool "ARM Ltd. Character LCD Driver"
434 depends on PLAT_VERSATILE
435 help
436 This is a driver for the character LCD found on the ARM Ltd.
437 Versatile and RealView Platform Baseboards. It doesn't do
438 very much more than display the text "ARM Linux" on the first
439 line and the Linux version on the second line, but that's
440 still useful.
441
442config BMP085
443 tristate
444 depends on SYSFS
445
446config BMP085_I2C
447 tristate "BMP085 digital pressure sensor on I2C"
448 select BMP085
449 select REGMAP_I2C
450 depends on I2C && SYSFS
451 help
452 Say Y here if you want to support Bosch Sensortec's digital pressure
453 sensor hooked to an I2C bus.
454
455 To compile this driver as a module, choose M here: the
456 module will be called bmp085-i2c.
457
458config BMP085_SPI
459 tristate "BMP085 digital pressure sensor on SPI"
460 select BMP085
461 select REGMAP_SPI
462 depends on SPI_MASTER && SYSFS
463 help
464 Say Y here if you want to support Bosch Sensortec's digital pressure
465 sensor hooked to an SPI bus.
466
467 To compile this driver as a module, choose M here: the
468 module will be called bmp085-spi.
469
470config PCH_PHUB
471 tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) PHUB"
472 select GENERIC_NET_UTILS
473 depends on PCI && (X86_32 || MIPS || COMPILE_TEST)
474 help
475 This driver is for PCH(Platform controller Hub) PHUB(Packet Hub) of
476 Intel Topcliff which is an IOH(Input/Output Hub) for x86 embedded
477 processor. The Topcliff has MAC address and Option ROM data in SROM.
478 This driver can access MAC address and Option ROM data in SROM.
479
480 This driver also can be used for LAPIS Semiconductor's IOH,
481 ML7213/ML7223/ML7831.
482 ML7213 which is for IVI(In-Vehicle Infotainment) use.
483 ML7223 IOH is for MP(Media Phone) use.
484 ML7831 IOH is for general purpose use.
485 ML7213/ML7223/ML7831 is companion chip for Intel Atom E6xx series.
486 ML7213/ML7223/ML7831 is completely compatible for Intel EG20T PCH.
487
488 To compile this driver as a module, choose M here: the module will
489 be called pch_phub.
490
491config USB_SWITCH_FSA9480
492 tristate "FSA9480 USB Switch"
493 depends on I2C
494 help
495 The FSA9480 is a USB port accessory detector and switch.
496 The FSA9480 is fully controlled using I2C and enables USB data,
497 stereo and mono audio, video, microphone and UART data to use
498 a common connector port.
499
500config LATTICE_ECP3_CONFIG
501 tristate "Lattice ECP3 FPGA bitstream configuration via SPI"
502 depends on SPI && SYSFS
503 select FW_LOADER
504 default n
505 help
506 This option enables support for bitstream configuration (programming
507 or loading) of the Lattice ECP3 FPGA family via SPI.
508
509 If unsure, say N.
510
511config SRAM
512 bool "Generic on-chip SRAM driver"
513 depends on HAS_IOMEM
514 select GENERIC_ALLOCATOR
515 help
516 This driver allows you to declare a memory region to be managed by
517 the genalloc API. It is supposed to be used for small on-chip SRAM
518 areas found on many SoCs.
519
520config VEXPRESS_SYSCFG
521 bool "Versatile Express System Configuration driver"
522 depends on VEXPRESS_CONFIG
523 default y
524 help
525 ARM Ltd. Versatile Express uses specialised platform configuration
526 bus. System Configuration interface is one of the possible means
527 of generating transactions on this bus.
528config PANEL
529 tristate "Parallel port LCD/Keypad Panel support"
530 depends on PARPORT
531 ---help---
532 Say Y here if you have an HD44780 or KS-0074 LCD connected to your
533 parallel port. This driver also features 4 and 6-key keypads. The LCD
534 is accessible through the /dev/lcd char device (10, 156), and the
535 keypad through /dev/keypad (10, 185). Both require misc device to be
536 enabled. This code can either be compiled as a module, or linked into
537 the kernel and started at boot. If you don't understand what all this
538 is about, say N.
539
540config PANEL_PARPORT
541 int "Default parallel port number (0=LPT1)"
542 depends on PANEL
543 range 0 255
544 default "0"
545 ---help---
546 This is the index of the parallel port the panel is connected to. One
547 driver instance only supports one parallel port, so if your keypad
548 and LCD are connected to two separate ports, you have to start two
549 modules with different arguments. Numbering starts with '0' for LPT1,
550 and so on.
551
552config PANEL_PROFILE
553 int "Default panel profile (0-5, 0=custom)"
554 depends on PANEL
555 range 0 5
556 default "5"
557 ---help---
558 To ease configuration, the driver supports different configuration
559 profiles for past and recent wirings. These profiles can also be
560 used to define an approximative configuration, completed by a few
561 other options. Here are the profiles :
562
563 0 = custom (see further)
564 1 = 2x16 parallel LCD, old keypad
565 2 = 2x16 serial LCD (KS-0074), new keypad
566 3 = 2x16 parallel LCD (Hantronix), no keypad
567 4 = 2x16 parallel LCD (Nexcom NSA1045) with Nexcom's keypad
568 5 = 2x40 parallel LCD (old one), with old keypad
569
570 Custom configurations allow you to define how your display is
571 wired to the parallel port, and how it works. This is only intended
572 for experts.
573
574config PANEL_KEYPAD
575 depends on PANEL && PANEL_PROFILE="0"
576 int "Keypad type (0=none, 1=old 6 keys, 2=new 6 keys, 3=Nexcom 4 keys)"
577 range 0 3
578 default 0
579 ---help---
580 This enables and configures a keypad connected to the parallel port.
581 The keys will be read from character device 10,185. Valid values are :
582
583 0 : do not enable this driver
584 1 : old 6 keys keypad
585 2 : new 6 keys keypad, as used on the server at www.ant-computing.com
586 3 : Nexcom NSA1045's 4 keys keypad
587
588 New profiles can be described in the driver source. The driver also
589 supports simultaneous keys pressed when the keypad supports them.
590
591config PANEL_LCD
592 depends on PANEL && PANEL_PROFILE="0"
593 int "LCD type (0=none, 1=custom, 2=old //, 3=ks0074, 4=hantronix, 5=Nexcom)"
594 range 0 5
595 default 0
596 ---help---
597 This enables and configures an LCD connected to the parallel port.
598 The driver includes an interpreter for escape codes starting with
599 '\e[L' which are specific to the LCD, and a few ANSI codes. The
600 driver will be registered as character device 10,156, usually
601 under the name '/dev/lcd'. There are a total of 6 supported types :
602
603 0 : do not enable the driver
604 1 : custom configuration and wiring (see further)
605 2 : 2x16 & 2x40 parallel LCD (old wiring)
606 3 : 2x16 serial LCD (KS-0074 based)
607 4 : 2x16 parallel LCD (Hantronix wiring)
608 5 : 2x16 parallel LCD (Nexcom wiring)
609
610 When type '1' is specified, other options will appear to configure
611 more precise aspects (wiring, dimensions, protocol, ...). Please note
612 that those values changed from the 2.4 driver for better consistency.
613
614config PANEL_LCD_HEIGHT
615 depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1"
616 int "Number of lines on the LCD (1-2)"
617 range 1 2
618 default 2
619 ---help---
620 This is the number of visible character lines on the LCD in custom profile.
621 It can either be 1 or 2.
622
623config PANEL_LCD_WIDTH
624 depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1"
625 int "Number of characters per line on the LCD (1-40)"
626 range 1 40
627 default 40
628 ---help---
629 This is the number of characters per line on the LCD in custom profile.
630 Common values are 16,20,24,40.
631
632config PANEL_LCD_BWIDTH
633 depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1"
634 int "Internal LCD line width (1-40, 40 by default)"
635 range 1 40
636 default 40
637 ---help---
638 Most LCDs use a standard controller which supports hardware lines of 40
639 characters, although sometimes only 16, 20 or 24 of them are really wired
640 to the terminal. This results in some non-visible but addressable characters,
641 and is the case for most parallel LCDs. Other LCDs, and some serial ones,
642 however, use the same line width internally as what is visible. The KS0074
643 for example, uses 16 characters per line for 16 visible characters per line.
644
645 This option lets you configure the value used by your LCD in 'custom' profile.
646 If you don't know, put '40' here.
647
648config PANEL_LCD_HWIDTH
649 depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1"
650 int "Hardware LCD line width (1-64, 64 by default)"
651 range 1 64
652 default 64
653 ---help---
654 Most LCDs use a single address bit to differentiate line 0 and line 1. Since
655 some of them need to be able to address 40 chars with the lower bits, they
656 often use the immediately superior power of 2, which is 64, to address the
657 next line.
658
659 If you don't know what your LCD uses, in doubt let 16 here for a 2x16, and
660 64 here for a 2x40.
661
662config PANEL_LCD_CHARSET
663 depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1"
664 int "LCD character set (0=normal, 1=KS0074)"
665 range 0 1
666 default 0
667 ---help---
668 Some controllers such as the KS0074 use a somewhat strange character set
669 where many symbols are at unusual places. The driver knows how to map
670 'standard' ASCII characters to the character sets used by these controllers.
671 Valid values are :
672
673 0 : normal (untranslated) character set
674 1 : KS0074 character set
675
676 If you don't know, use the normal one (0).
677
678config PANEL_LCD_PROTO
679 depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1"
680 int "LCD communication mode (0=parallel 8 bits, 1=serial)"
681 range 0 1
682 default 0
683 ---help---
684 This driver now supports any serial or parallel LCD wired to a parallel
685 port. But before assigning signals, the driver needs to know if it will
686 be driving a serial LCD or a parallel one. Serial LCDs only use 2 wires
687 (SDA/SCL), while parallel ones use 2 or 3 wires for the control signals
688 (E, RS, sometimes RW), and 4 or 8 for the data. Use 0 here for a 8 bits
689 parallel LCD, and 1 for a serial LCD.
690
691config PANEL_LCD_PIN_E
692 depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO="0"
693 int "Parallel port pin number & polarity connected to the LCD E signal (-17...17) "
694 range -17 17
695 default 14
696 ---help---
697 This describes the number of the parallel port pin to which the LCD 'E'
698 signal has been connected. It can be :
699
700 0 : no connection (eg: connected to ground)
701 1..17 : directly connected to any of these pins on the DB25 plug
702 -1..-17 : connected to the same pin through an inverter (eg: transistor).
703
704 Default for the 'E' pin in custom profile is '14' (AUTOFEED).
705
706config PANEL_LCD_PIN_RS
707 depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO="0"
708 int "Parallel port pin number & polarity connected to the LCD RS signal (-17...17) "
709 range -17 17
710 default 17
711 ---help---
712 This describes the number of the parallel port pin to which the LCD 'RS'
713 signal has been connected. It can be :
714
715 0 : no connection (eg: connected to ground)
716 1..17 : directly connected to any of these pins on the DB25 plug
717 -1..-17 : connected to the same pin through an inverter (eg: transistor).
718
719 Default for the 'RS' pin in custom profile is '17' (SELECT IN).
720
721config PANEL_LCD_PIN_RW
722 depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO="0"
723 int "Parallel port pin number & polarity connected to the LCD RW signal (-17...17) "
724 range -17 17
725 default 16
726 ---help---
727 This describes the number of the parallel port pin to which the LCD 'RW'
728 signal has been connected. It can be :
729
730 0 : no connection (eg: connected to ground)
731 1..17 : directly connected to any of these pins on the DB25 plug
732 -1..-17 : connected to the same pin through an inverter (eg: transistor).
733
734 Default for the 'RW' pin in custom profile is '16' (INIT).
735
736config PANEL_LCD_PIN_SCL
737 depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO!="0"
738 int "Parallel port pin number & polarity connected to the LCD SCL signal (-17...17) "
739 range -17 17
740 default 1
741 ---help---
742 This describes the number of the parallel port pin to which the serial
743 LCD 'SCL' signal has been connected. It can be :
744
745 0 : no connection (eg: connected to ground)
746 1..17 : directly connected to any of these pins on the DB25 plug
747 -1..-17 : connected to the same pin through an inverter (eg: transistor).
748
749 Default for the 'SCL' pin in custom profile is '1' (STROBE).
750
751config PANEL_LCD_PIN_SDA
752 depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1" && PANEL_LCD_PROTO!="0"
753 int "Parallel port pin number & polarity connected to the LCD SDA signal (-17...17) "
754 range -17 17
755 default 2
756 ---help---
757 This describes the number of the parallel port pin to which the serial
758 LCD 'SDA' signal has been connected. It can be :
759
760 0 : no connection (eg: connected to ground)
761 1..17 : directly connected to any of these pins on the DB25 plug
762 -1..-17 : connected to the same pin through an inverter (eg: transistor).
763
764 Default for the 'SDA' pin in custom profile is '2' (D0).
765
766config PANEL_LCD_PIN_BL
767 depends on PANEL && PANEL_PROFILE="0" && PANEL_LCD="1"
768 int "Parallel port pin number & polarity connected to the LCD backlight signal (-17...17) "
769 range -17 17
770 default 0
771 ---help---
772 This describes the number of the parallel port pin to which the LCD 'BL' signal
773 has been connected. It can be :
774
775 0 : no connection (eg: connected to ground)
776 1..17 : directly connected to any of these pins on the DB25 plug
777 -1..-17 : connected to the same pin through an inverter (eg: transistor).
778
779 Default for the 'BL' pin in custom profile is '0' (uncontrolled).
780
781config PANEL_CHANGE_MESSAGE
782 depends on PANEL
783 bool "Change LCD initialization message ?"
784 default "n"
785 ---help---
786 This allows you to replace the boot message indicating the kernel version
787 and the driver version with a custom message. This is useful on appliances
788 where a simple 'Starting system' message can be enough to stop a customer
789 from worrying.
790
791 If you say 'Y' here, you'll be able to choose a message yourself. Otherwise,
792 say 'N' and keep the default message with the version.
793
794config PANEL_BOOT_MESSAGE
795 depends on PANEL && PANEL_CHANGE_MESSAGE="y"
796 string "New initialization message"
797 default ""
798 ---help---
799 This allows you to replace the boot message indicating the kernel version
800 and the driver version with a custom message. This is useful on appliances
801 where a simple 'Starting system' message can be enough to stop a customer
802 from worrying.
803
804 An empty message will only clear the display at driver init time. Any other
805 printf()-formatted message is valid with newline and escape codes.
806
807source "drivers/misc/c2port/Kconfig"
808source "drivers/misc/eeprom/Kconfig"
809source "drivers/misc/cb710/Kconfig"
810source "drivers/misc/ti-st/Kconfig"
811source "drivers/misc/lis3lv02d/Kconfig"
812source "drivers/misc/altera-stapl/Kconfig"
813source "drivers/misc/mei/Kconfig"
814source "drivers/misc/vmw_vmci/Kconfig"
815source "drivers/misc/mic/Kconfig"
816source "drivers/misc/genwqe/Kconfig"
817source "drivers/misc/echo/Kconfig"
818source "drivers/misc/cxl/Kconfig"
819endmenu
1#
2# Misc strange devices
3#
4
5menu "Misc devices"
6
7config SENSORS_LIS3LV02D
8 tristate
9 depends on INPUT
10 select INPUT_POLLDEV
11 default n
12
13config AD525X_DPOT
14 tristate "Analog Devices Digital Potentiometers"
15 depends on (I2C || SPI) && SYSFS
16 help
17 If you say yes here, you get support for the Analog Devices
18 AD5258, AD5259, AD5251, AD5252, AD5253, AD5254, AD5255
19 AD5160, AD5161, AD5162, AD5165, AD5200, AD5201, AD5203,
20 AD5204, AD5206, AD5207, AD5231, AD5232, AD5233, AD5235,
21 AD5260, AD5262, AD5263, AD5290, AD5291, AD5292, AD5293,
22 AD7376, AD8400, AD8402, AD8403, ADN2850, AD5241, AD5242,
23 AD5243, AD5245, AD5246, AD5247, AD5248, AD5280, AD5282,
24 ADN2860, AD5273, AD5171, AD5170, AD5172, AD5173, AD5270,
25 AD5271, AD5272, AD5274
26 digital potentiometer chips.
27
28 See Documentation/misc-devices/ad525x_dpot.txt for the
29 userspace interface.
30
31 This driver can also be built as a module. If so, the module
32 will be called ad525x_dpot.
33
34config AD525X_DPOT_I2C
35 tristate "support I2C bus connection"
36 depends on AD525X_DPOT && I2C
37 help
38 Say Y here if you have a digital potentiometers hooked to an I2C bus.
39
40 To compile this driver as a module, choose M here: the
41 module will be called ad525x_dpot-i2c.
42
43config AD525X_DPOT_SPI
44 tristate "support SPI bus connection"
45 depends on AD525X_DPOT && SPI_MASTER
46 help
47 Say Y here if you have a digital potentiometers hooked to an SPI bus.
48
49 If unsure, say N (but it's safe to say "Y").
50
51 To compile this driver as a module, choose M here: the
52 module will be called ad525x_dpot-spi.
53
54config ATMEL_PWM
55 tristate "Atmel AT32/AT91 PWM support"
56 depends on HAVE_CLK
57 help
58 This option enables device driver support for the PWM channels
59 on certain Atmel processors. Pulse Width Modulation is used for
60 purposes including software controlled power-efficient backlights
61 on LCD displays, motor control, and waveform generation.
62
63config AB8500_PWM
64 bool "AB8500 PWM support"
65 depends on AB8500_CORE && ARCH_U8500
66 select HAVE_PWM
67 help
68 This driver exports functions to enable/disble/config/free Pulse
69 Width Modulation in the Analog Baseband Chip AB8500.
70 It is used by led and backlight driver to control the intensity.
71
72config ATMEL_TCLIB
73 bool "Atmel AT32/AT91 Timer/Counter Library"
74 depends on (AVR32 || ARCH_AT91)
75 help
76 Select this if you want a library to allocate the Timer/Counter
77 blocks found on many Atmel processors. This facilitates using
78 these blocks by different drivers despite processor differences.
79
80config ATMEL_TCB_CLKSRC
81 bool "TC Block Clocksource"
82 depends on ATMEL_TCLIB
83 default y
84 help
85 Select this to get a high precision clocksource based on a
86 TC block with a 5+ MHz base clock rate. Two timer channels
87 are combined to make a single 32-bit timer.
88
89 When GENERIC_CLOCKEVENTS is defined, the third timer channel
90 may be used as a clock event device supporting oneshot mode
91 (delays of up to two seconds) based on the 32 KiHz clock.
92
93config ATMEL_TCB_CLKSRC_BLOCK
94 int
95 depends on ATMEL_TCB_CLKSRC
96 prompt "TC Block" if ARCH_AT91RM9200 || ARCH_AT91SAM9260 || CPU_AT32AP700X
97 default 0
98 range 0 1
99 help
100 Some chips provide more than one TC block, so you have the
101 choice of which one to use for the clock framework. The other
102 TC can be used for other purposes, such as PWM generation and
103 interval timing.
104
105config IBM_ASM
106 tristate "Device driver for IBM RSA service processor"
107 depends on X86 && PCI && INPUT && EXPERIMENTAL
108 ---help---
109 This option enables device driver support for in-band access to the
110 IBM RSA (Condor) service processor in eServer xSeries systems.
111 The ibmasm device driver allows user space application to access
112 ASM (Advanced Systems Management) functions on the service
113 processor. The driver is meant to be used in conjunction with
114 a user space API.
115 The ibmasm driver also enables the OS to use the UART on the
116 service processor board as a regular serial port. To make use of
117 this feature serial driver support (CONFIG_SERIAL_8250) must be
118 enabled.
119
120 WARNING: This software may not be supported or function
121 correctly on your IBM server. Please consult the IBM ServerProven
122 website <http://www-03.ibm.com/systems/info/x86servers/serverproven/compat/us/>
123 for information on the specific driver level and support statement
124 for your IBM server.
125
126config PHANTOM
127 tristate "Sensable PHANToM (PCI)"
128 depends on PCI
129 help
130 Say Y here if you want to build a driver for Sensable PHANToM device.
131
132 This driver is only for PCI PHANToMs.
133
134 If you choose to build module, its name will be phantom. If unsure,
135 say N here.
136
137config INTEL_MID_PTI
138 tristate "Parallel Trace Interface for MIPI P1149.7 cJTAG standard"
139 depends on PCI
140 default n
141 help
142 The PTI (Parallel Trace Interface) driver directs
143 trace data routed from various parts in the system out
144 through an Intel Penwell PTI port and out of the mobile
145 device for analysis with a debugging tool (Lauterbach or Fido).
146
147 You should select this driver if the target kernel is meant for
148 an Intel Atom (non-netbook) mobile device containing a MIPI
149 P1149.7 standard implementation.
150
151config SGI_IOC4
152 tristate "SGI IOC4 Base IO support"
153 depends on PCI
154 ---help---
155 This option enables basic support for the IOC4 chip on certain
156 SGI IO controller cards (IO9, IO10, and PCI-RT). This option
157 does not enable any specific functions on such a card, but provides
158 necessary infrastructure for other drivers to utilize.
159
160 If you have an SGI Altix with an IOC4-based card say Y.
161 Otherwise say N.
162
163config TIFM_CORE
164 tristate "TI Flash Media interface support (EXPERIMENTAL)"
165 depends on EXPERIMENTAL && PCI
166 help
167 If you want support for Texas Instruments(R) Flash Media adapters
168 you should select this option and then also choose an appropriate
169 host adapter, such as 'TI Flash Media PCI74xx/PCI76xx host adapter
170 support', if you have a TI PCI74xx compatible card reader, for
171 example.
172 You will also have to select some flash card format drivers. MMC/SD
173 cards are supported via 'MMC/SD Card support: TI Flash Media MMC/SD
174 Interface support (MMC_TIFM_SD)'.
175
176 To compile this driver as a module, choose M here: the module will
177 be called tifm_core.
178
179config TIFM_7XX1
180 tristate "TI Flash Media PCI74xx/PCI76xx host adapter support (EXPERIMENTAL)"
181 depends on PCI && TIFM_CORE && EXPERIMENTAL
182 default TIFM_CORE
183 help
184 This option enables support for Texas Instruments(R) PCI74xx and
185 PCI76xx families of Flash Media adapters, found in many laptops.
186 To make actual use of the device, you will have to select some
187 flash card format drivers, as outlined in the TIFM_CORE Help.
188
189 To compile this driver as a module, choose M here: the module will
190 be called tifm_7xx1.
191
192config ICS932S401
193 tristate "Integrated Circuits ICS932S401"
194 depends on I2C && EXPERIMENTAL
195 help
196 If you say yes here you get support for the Integrated Circuits
197 ICS932S401 clock control chips.
198
199 This driver can also be built as a module. If so, the module
200 will be called ics932s401.
201
202config ATMEL_SSC
203 tristate "Device driver for Atmel SSC peripheral"
204 depends on AVR32 || ARCH_AT91
205 ---help---
206 This option enables device driver support for Atmel Synchronized
207 Serial Communication peripheral (SSC).
208
209 The SSC peripheral supports a wide variety of serial frame based
210 communications, i.e. I2S, SPI, etc.
211
212 If unsure, say N.
213
214config ENCLOSURE_SERVICES
215 tristate "Enclosure Services"
216 default n
217 help
218 Provides support for intelligent enclosures (bays which
219 contain storage devices). You also need either a host
220 driver (SCSI/ATA) which supports enclosures
221 or a SCSI enclosure device (SES) to use these services.
222
223config SGI_XP
224 tristate "Support communication between SGI SSIs"
225 depends on NET
226 depends on (IA64_GENERIC || IA64_SGI_SN2 || IA64_SGI_UV || X86_UV) && SMP
227 select IA64_UNCACHED_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
228 select GENERIC_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
229 select SGI_GRU if X86_64 && SMP
230 ---help---
231 An SGI machine can be divided into multiple Single System
232 Images which act independently of each other and have
233 hardware based memory protection from the others. Enabling
234 this feature will allow for direct communication between SSIs
235 based on a network adapter and DMA messaging.
236
237config CS5535_MFGPT
238 tristate "CS5535/CS5536 Geode Multi-Function General Purpose Timer (MFGPT) support"
239 depends on PCI && X86 && MFD_CS5535
240 default n
241 help
242 This driver provides access to MFGPT functionality for other
243 drivers that need timers. MFGPTs are available in the CS5535 and
244 CS5536 companion chips that are found in AMD Geode and several
245 other platforms. They have a better resolution and max interval
246 than the generic PIT, and are suitable for use as high-res timers.
247 You probably don't want to enable this manually; other drivers that
248 make use of it should enable it.
249
250config CS5535_MFGPT_DEFAULT_IRQ
251 int
252 depends on CS5535_MFGPT
253 default 7
254 help
255 MFGPTs on the CS5535 require an interrupt. The selected IRQ
256 can be overridden as a module option as well as by driver that
257 use the cs5535_mfgpt_ API; however, different architectures might
258 want to use a different IRQ by default. This is here for
259 architectures to set as necessary.
260
261config CS5535_CLOCK_EVENT_SRC
262 tristate "CS5535/CS5536 high-res timer (MFGPT) events"
263 depends on GENERIC_CLOCKEVENTS && CS5535_MFGPT
264 help
265 This driver provides a clock event source based on the MFGPT
266 timer(s) in the CS5535 and CS5536 companion chips.
267 MFGPTs have a better resolution and max interval than the
268 generic PIT, and are suitable for use as high-res timers.
269
270config HP_ILO
271 tristate "Channel interface driver for the HP iLO processor"
272 depends on PCI
273 default n
274 help
275 The channel interface driver allows applications to communicate
276 with iLO management processors present on HP ProLiant servers.
277 Upon loading, the driver creates /dev/hpilo/dXccbN files, which
278 can be used to gather data from the management processor, via
279 read and write system calls.
280
281 To compile this driver as a module, choose M here: the
282 module will be called hpilo.
283
284config SGI_GRU
285 tristate "SGI GRU driver"
286 depends on X86_UV && SMP
287 default n
288 select MMU_NOTIFIER
289 ---help---
290 The GRU is a hardware resource located in the system chipset. The GRU
291 contains memory that can be mmapped into the user address space. This memory is
292 used to communicate with the GRU to perform functions such as load/store,
293 scatter/gather, bcopy, AMOs, etc. The GRU is directly accessed by user
294 instructions using user virtual addresses. GRU instructions (ex., bcopy) use
295 user virtual addresses for operands.
296
297 If you are not running on a SGI UV system, say N.
298
299config SGI_GRU_DEBUG
300 bool "SGI GRU driver debug"
301 depends on SGI_GRU
302 default n
303 ---help---
304 This option enables addition debugging code for the SGI GRU driver. If
305 you are unsure, say N.
306
307config APDS9802ALS
308 tristate "Medfield Avago APDS9802 ALS Sensor module"
309 depends on I2C
310 help
311 If you say yes here you get support for the ALS APDS9802 ambient
312 light sensor.
313
314 This driver can also be built as a module. If so, the module
315 will be called apds9802als.
316
317config ISL29003
318 tristate "Intersil ISL29003 ambient light sensor"
319 depends on I2C && SYSFS
320 help
321 If you say yes here you get support for the Intersil ISL29003
322 ambient light sensor.
323
324 This driver can also be built as a module. If so, the module
325 will be called isl29003.
326
327config ISL29020
328 tristate "Intersil ISL29020 ambient light sensor"
329 depends on I2C
330 help
331 If you say yes here you get support for the Intersil ISL29020
332 ambient light sensor.
333
334 This driver can also be built as a module. If so, the module
335 will be called isl29020.
336
337config SENSORS_TSL2550
338 tristate "Taos TSL2550 ambient light sensor"
339 depends on I2C && SYSFS
340 help
341 If you say yes here you get support for the Taos TSL2550
342 ambient light sensor.
343
344 This driver can also be built as a module. If so, the module
345 will be called tsl2550.
346
347config SENSORS_BH1780
348 tristate "ROHM BH1780GLI ambient light sensor"
349 depends on I2C && SYSFS
350 help
351 If you say yes here you get support for the ROHM BH1780GLI
352 ambient light sensor.
353
354 This driver can also be built as a module. If so, the module
355 will be called bh1780gli.
356
357config SENSORS_BH1770
358 tristate "BH1770GLC / SFH7770 combined ALS - Proximity sensor"
359 depends on I2C
360 ---help---
361 Say Y here if you want to build a driver for BH1770GLC (ROHM) or
362 SFH7770 (Osram) combined ambient light and proximity sensor chip.
363
364 To compile this driver as a module, choose M here: the
365 module will be called bh1770glc. If unsure, say N here.
366
367config SENSORS_APDS990X
368 tristate "APDS990X combined als and proximity sensors"
369 depends on I2C
370 default n
371 ---help---
372 Say Y here if you want to build a driver for Avago APDS990x
373 combined ambient light and proximity sensor chip.
374
375 To compile this driver as a module, choose M here: the
376 module will be called apds990x. If unsure, say N here.
377
378config HMC6352
379 tristate "Honeywell HMC6352 compass"
380 depends on I2C
381 help
382 This driver provides support for the Honeywell HMC6352 compass,
383 providing configuration and heading data via sysfs.
384
385config EP93XX_PWM
386 tristate "EP93xx PWM support"
387 depends on ARCH_EP93XX
388 help
389 This option enables device driver support for the PWM channels
390 on the Cirrus EP93xx processors. The EP9307 chip only has one
391 PWM channel all the others have two, the second channel is an
392 alternate function of the EGPIO14 pin. A sysfs interface is
393 provided to control the PWM channels.
394
395 To compile this driver as a module, choose M here: the module will
396 be called ep93xx_pwm.
397
398config DS1682
399 tristate "Dallas DS1682 Total Elapsed Time Recorder with Alarm"
400 depends on I2C && EXPERIMENTAL
401 help
402 If you say yes here you get support for Dallas Semiconductor
403 DS1682 Total Elapsed Time Recorder.
404
405 This driver can also be built as a module. If so, the module
406 will be called ds1682.
407
408config SPEAR13XX_PCIE_GADGET
409 bool "PCIe gadget support for SPEAr13XX platform"
410 depends on ARCH_SPEAR13XX
411 default n
412 help
413 This option enables gadget support for PCIe controller. If
414 board file defines any controller as PCIe endpoint then a sysfs
415 entry will be created for that controller. User can use these
416 sysfs node to configure PCIe EP as per his requirements.
417
418config TI_DAC7512
419 tristate "Texas Instruments DAC7512"
420 depends on SPI && SYSFS
421 help
422 If you say yes here you get support for the Texas Instruments
423 DAC7512 16-bit digital-to-analog converter.
424
425 This driver can also be built as a module. If so, the module
426 will be called ti_dac7512.
427
428config VMWARE_BALLOON
429 tristate "VMware Balloon Driver"
430 depends on X86
431 help
432 This is VMware physical memory management driver which acts
433 like a "balloon" that can be inflated to reclaim physical pages
434 by reserving them in the guest and invalidating them in the
435 monitor, freeing up the underlying machine pages so they can
436 be allocated to other guests. The balloon can also be deflated
437 to allow the guest to use more physical memory.
438
439 If unsure, say N.
440
441 To compile this driver as a module, choose M here: the
442 module will be called vmw_balloon.
443
444config ARM_CHARLCD
445 bool "ARM Ltd. Character LCD Driver"
446 depends on PLAT_VERSATILE
447 help
448 This is a driver for the character LCD found on the ARM Ltd.
449 Versatile and RealView Platform Baseboards. It doesn't do
450 very much more than display the text "ARM Linux" on the first
451 line and the Linux version on the second line, but that's
452 still useful.
453
454config BMP085
455 bool
456 depends on SYSFS
457
458config BMP085_I2C
459 tristate "BMP085 digital pressure sensor on I2C"
460 select BMP085
461 select REGMAP_I2C
462 depends on I2C && SYSFS
463 help
464 Say Y here if you want to support Bosch Sensortec's digital pressure
465 sensor hooked to an I2C bus.
466
467 To compile this driver as a module, choose M here: the
468 module will be called bmp085-i2c.
469
470config BMP085_SPI
471 tristate "BMP085 digital pressure sensor on SPI"
472 select BMP085
473 select REGMAP_SPI
474 depends on SPI_MASTER && SYSFS
475 help
476 Say Y here if you want to support Bosch Sensortec's digital pressure
477 sensor hooked to an SPI bus.
478
479 To compile this driver as a module, choose M here: the
480 module will be called bmp085-spi.
481
482config PCH_PHUB
483 tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) PHUB"
484 depends on PCI
485 help
486 This driver is for PCH(Platform controller Hub) PHUB(Packet Hub) of
487 Intel Topcliff which is an IOH(Input/Output Hub) for x86 embedded
488 processor. The Topcliff has MAC address and Option ROM data in SROM.
489 This driver can access MAC address and Option ROM data in SROM.
490
491 This driver also can be used for LAPIS Semiconductor's IOH,
492 ML7213/ML7223/ML7831.
493 ML7213 which is for IVI(In-Vehicle Infotainment) use.
494 ML7223 IOH is for MP(Media Phone) use.
495 ML7831 IOH is for general purpose use.
496 ML7213/ML7223/ML7831 is companion chip for Intel Atom E6xx series.
497 ML7213/ML7223/ML7831 is completely compatible for Intel EG20T PCH.
498
499 To compile this driver as a module, choose M here: the module will
500 be called pch_phub.
501
502config USB_SWITCH_FSA9480
503 tristate "FSA9480 USB Switch"
504 depends on I2C
505 help
506 The FSA9480 is a USB port accessory detector and switch.
507 The FSA9480 is fully controlled using I2C and enables USB data,
508 stereo and mono audio, video, microphone and UART data to use
509 a common connector port.
510
511source "drivers/misc/c2port/Kconfig"
512source "drivers/misc/eeprom/Kconfig"
513source "drivers/misc/cb710/Kconfig"
514source "drivers/misc/iwmc3200top/Kconfig"
515source "drivers/misc/ti-st/Kconfig"
516source "drivers/misc/lis3lv02d/Kconfig"
517source "drivers/misc/carma/Kconfig"
518source "drivers/misc/altera-stapl/Kconfig"
519source "drivers/misc/mei/Kconfig"
520endmenu