Loading...
1#
2# USB Host Controller Drivers
3#
4comment "USB Host Controller Drivers"
5
6config USB_C67X00_HCD
7 tristate "Cypress C67x00 HCD support"
8 depends on HAS_IOMEM
9 help
10 The Cypress C67x00 (EZ-Host/EZ-OTG) chips are dual-role
11 host/peripheral/OTG USB controllers.
12
13 Enable this option to support this chip in host controller mode.
14 If unsure, say N.
15
16 To compile this driver as a module, choose M here: the
17 module will be called c67x00.
18
19config USB_XHCI_HCD
20 tristate "xHCI HCD (USB 3.0) support"
21 depends on HAS_DMA && HAS_IOMEM
22 ---help---
23 The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0
24 "SuperSpeed" host controller hardware.
25
26 To compile this driver as a module, choose M here: the
27 module will be called xhci-hcd.
28
29if USB_XHCI_HCD
30
31config USB_XHCI_PCI
32 tristate
33 depends on PCI
34 default y
35
36config USB_XHCI_PLATFORM
37 tristate "Generic xHCI driver for a platform device"
38 ---help---
39 Adds an xHCI host driver for a generic platform device, which
40 provides a memory space and an irq.
41 It is also a prerequisite for platform specific drivers that
42 implement some extra quirks.
43
44 If unsure, say N.
45
46config USB_XHCI_MTK
47 tristate "xHCI support for Mediatek MT65xx"
48 select MFD_SYSCON
49 depends on ARCH_MEDIATEK || COMPILE_TEST
50 ---help---
51 Say 'Y' to enable the support for the xHCI host controller
52 found in Mediatek MT65xx SoCs.
53 If unsure, say N.
54
55config USB_XHCI_MVEBU
56 tristate "xHCI support for Marvell Armada 375/38x"
57 select USB_XHCI_PLATFORM
58 depends on HAS_IOMEM
59 depends on ARCH_MVEBU || COMPILE_TEST
60 ---help---
61 Say 'Y' to enable the support for the xHCI host controller
62 found in Marvell Armada 375/38x ARM SOCs.
63
64config USB_XHCI_RCAR
65 tristate "xHCI support for Renesas R-Car SoCs"
66 select USB_XHCI_PLATFORM
67 depends on ARCH_RENESAS || COMPILE_TEST
68 ---help---
69 Say 'Y' to enable the support for the xHCI host controller
70 found in Renesas R-Car ARM SoCs.
71
72endif # USB_XHCI_HCD
73
74config USB_EHCI_HCD
75 tristate "EHCI HCD (USB 2.0) support"
76 depends on HAS_DMA && HAS_IOMEM
77 ---help---
78 The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
79 "high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
80 If your USB host controller supports USB 2.0, you will likely want to
81 configure this Host Controller Driver.
82
83 EHCI controllers are packaged with "companion" host controllers (OHCI
84 or UHCI) to handle USB 1.1 devices connected to root hub ports. Ports
85 will connect to EHCI if the device is high speed, otherwise they
86 connect to a companion controller. If you configure EHCI, you should
87 probably configure the OHCI (for NEC and some other vendors) USB Host
88 Controller Driver or UHCI (for Via motherboards) Host Controller
89 Driver too.
90
91 You may want to read <file:Documentation/usb/ehci.txt>.
92
93 To compile this driver as a module, choose M here: the
94 module will be called ehci-hcd.
95
96config USB_EHCI_ROOT_HUB_TT
97 bool "Root Hub Transaction Translators"
98 depends on USB_EHCI_HCD
99 ---help---
100 Some EHCI chips have vendor-specific extensions to integrate
101 transaction translators, so that no OHCI or UHCI companion
102 controller is needed. It's safe to say "y" even if your
103 controller doesn't support this feature.
104
105 This supports the EHCI implementation that's originally
106 from ARC, and has since changed hands a few times.
107
108config USB_EHCI_TT_NEWSCHED
109 bool "Improved Transaction Translator scheduling"
110 depends on USB_EHCI_HCD
111 default y
112 ---help---
113 This changes the periodic scheduling code to fill more of the low
114 and full speed bandwidth available from the Transaction Translator
115 (TT) in USB 2.0 hubs. Without this, only one transfer will be
116 issued in each microframe, significantly reducing the number of
117 periodic low/fullspeed transfers possible.
118
119 If you have multiple periodic low/fullspeed devices connected to a
120 highspeed USB hub which is connected to a highspeed USB Host
121 Controller, and some of those devices will not work correctly
122 (possibly due to "ENOSPC" or "-28" errors), say Y. Conversely, if
123 you have only one such device and it doesn't work, you could try
124 saying N.
125
126 If unsure, say Y.
127
128if USB_EHCI_HCD
129
130config USB_EHCI_PCI
131 tristate
132 depends on PCI
133 default y
134
135config USB_EHCI_HCD_PMC_MSP
136 tristate "EHCI support for on-chip PMC MSP71xx USB controller"
137 depends on MSP_HAS_USB
138 default n
139 select USB_EHCI_BIG_ENDIAN_DESC
140 select USB_EHCI_BIG_ENDIAN_MMIO
141 ---help---
142 Enables support for the onchip USB controller on the PMC_MSP7100 Family SoC's.
143 If unsure, say N.
144
145config XPS_USB_HCD_XILINX
146 bool "Use Xilinx usb host EHCI controller core"
147 depends on (PPC32 || MICROBLAZE)
148 select USB_EHCI_BIG_ENDIAN_DESC
149 select USB_EHCI_BIG_ENDIAN_MMIO
150 ---help---
151 Xilinx xps USB host controller core is EHCI compliant and has
152 transaction translator built-in. It can be configured to either
153 support both high speed and full speed devices, or high speed
154 devices only.
155
156config USB_EHCI_FSL
157 tristate "Support for Freescale PPC on-chip EHCI USB controller"
158 depends on FSL_SOC
159 select USB_EHCI_ROOT_HUB_TT
160 ---help---
161 Variation of ARC USB block used in some Freescale chips.
162
163config USB_EHCI_MXC
164 tristate "Support for Freescale i.MX on-chip EHCI USB controller"
165 depends on ARCH_MXC
166 select USB_EHCI_ROOT_HUB_TT
167 ---help---
168 Variation of ARC USB block used in some Freescale chips.
169
170config USB_EHCI_HCD_OMAP
171 tristate "EHCI support for OMAP3 and later chips"
172 depends on ARCH_OMAP
173 select NOP_USB_XCEIV
174 default y
175 ---help---
176 Enables support for the on-chip EHCI controller on
177 OMAP3 and later chips.
178
179config USB_EHCI_HCD_ORION
180 tristate "Support for Marvell EBU on-chip EHCI USB controller"
181 depends on USB_EHCI_HCD && PLAT_ORION
182 default y
183 ---help---
184 Enables support for the on-chip EHCI controller on Marvell's
185 embedded ARM SoCs, including Orion, Kirkwood, Dove, Armada XP,
186 Armada 370. This is different from the EHCI implementation
187 on Marvell's mobile PXA and MMP SoC, see "EHCI support for
188 Marvell PXA/MMP USB controller" for those.
189
190config USB_EHCI_HCD_SPEAR
191 tristate "Support for ST SPEAr on-chip EHCI USB controller"
192 depends on USB_EHCI_HCD && PLAT_SPEAR
193 default y
194 ---help---
195 Enables support for the on-chip EHCI controller on
196 ST SPEAr chips.
197
198config USB_EHCI_HCD_STI
199 tristate "Support for ST STiHxxx on-chip EHCI USB controller"
200 depends on ARCH_STI && OF
201 select GENERIC_PHY
202 select USB_EHCI_HCD_PLATFORM
203 help
204 Enable support for the on-chip EHCI controller found on
205 STMicroelectronics consumer electronics SoC's.
206
207config USB_EHCI_HCD_AT91
208 tristate "Support for Atmel on-chip EHCI USB controller"
209 depends on USB_EHCI_HCD && ARCH_AT91
210 default y
211 ---help---
212 Enables support for the on-chip EHCI controller on
213 Atmel chips.
214
215config USB_EHCI_MSM
216 tristate "Support for Qualcomm QSD/MSM on-chip EHCI USB controller"
217 depends on ARCH_QCOM
218 select USB_EHCI_ROOT_HUB_TT
219 ---help---
220 Enables support for the USB Host controller present on the
221 Qualcomm chipsets. Root Hub has inbuilt TT.
222 This driver depends on OTG driver for PHY initialization,
223 clock management, powering up VBUS, and power management.
224 This driver is not supported on boards like trout which
225 has an external PHY.
226
227config USB_EHCI_TEGRA
228 tristate "NVIDIA Tegra HCD support"
229 depends on ARCH_TEGRA
230 select USB_EHCI_ROOT_HUB_TT
231 select USB_PHY
232 select USB_ULPI
233 select USB_ULPI_VIEWPORT
234 help
235 This driver enables support for the internal USB Host Controllers
236 found in NVIDIA Tegra SoCs. The controllers are EHCI compliant.
237
238config USB_EHCI_HCD_PPC_OF
239 bool "EHCI support for PPC USB controller on OF platform bus"
240 depends on PPC
241 default y
242 ---help---
243 Enables support for the USB controller present on the PowerPC
244 OpenFirmware platform bus.
245
246config USB_EHCI_SH
247 bool "EHCI support for SuperH USB controller"
248 depends on SUPERH
249 ---help---
250 Enables support for the on-chip EHCI controller on the SuperH.
251 If you use the PCI EHCI controller, this option is not necessary.
252
253config USB_EHCI_EXYNOS
254 tristate "EHCI support for Samsung S5P/EXYNOS SoC Series"
255 depends on ARCH_S5PV210 || ARCH_EXYNOS
256 help
257 Enable support for the Samsung Exynos SOC's on-chip EHCI controller.
258
259config USB_EHCI_MV
260 bool "EHCI support for Marvell PXA/MMP USB controller"
261 depends on (ARCH_PXA || ARCH_MMP)
262 select USB_EHCI_ROOT_HUB_TT
263 ---help---
264 Enables support for Marvell (including PXA and MMP series) on-chip
265 USB SPH and OTG controller. SPH is a single port host, and it can
266 only be EHCI host. OTG is controller that can switch to host mode.
267 Note that this driver will not work on Marvell's other EHCI
268 controller used by the EBU-type SoCs including Orion, Kirkwood,
269 Dova, Armada 370 and Armada XP. See "Support for Marvell EBU
270 on-chip EHCI USB controller" for those.
271
272config USB_W90X900_EHCI
273 tristate "W90X900(W90P910) EHCI support"
274 depends on ARCH_W90X900
275 ---help---
276 Enables support for the W90X900 USB controller
277
278config USB_CNS3XXX_EHCI
279 bool "Cavium CNS3XXX EHCI Module (DEPRECATED)"
280 depends on ARCH_CNS3XXX
281 select USB_EHCI_HCD_PLATFORM
282 ---help---
283 This option is deprecated now and the driver was removed, use
284 USB_EHCI_HCD_PLATFORM instead.
285
286 Enable support for the CNS3XXX SOC's on-chip EHCI controller.
287 It is needed for high-speed (480Mbit/sec) USB 2.0 device
288 support.
289
290config USB_EHCI_ATH79
291 bool "EHCI support for AR7XXX/AR9XXX SoCs (DEPRECATED)"
292 depends on (SOC_AR71XX || SOC_AR724X || SOC_AR913X || SOC_AR933X)
293 select USB_EHCI_ROOT_HUB_TT
294 select USB_EHCI_HCD_PLATFORM
295 default y
296 ---help---
297 This option is deprecated now and the driver was removed, use
298 USB_EHCI_HCD_PLATFORM instead.
299
300 Enables support for the built-in EHCI controller present
301 on the Atheros AR7XXX/AR9XXX SoCs.
302
303config USB_EHCI_HCD_PLATFORM
304 tristate "Generic EHCI driver for a platform device"
305 default n
306 ---help---
307 Adds an EHCI host driver for a generic platform device, which
308 provides a memory space and an irq.
309
310 If unsure, say N.
311
312config USB_OCTEON_EHCI
313 bool "Octeon on-chip EHCI support (DEPRECATED)"
314 depends on CAVIUM_OCTEON_SOC
315 default n
316 select USB_EHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
317 select USB_EHCI_HCD_PLATFORM
318 help
319 This option is deprecated now and the driver was removed, use
320 USB_EHCI_HCD_PLATFORM instead.
321
322 Enable support for the Octeon II SOC's on-chip EHCI
323 controller. It is needed for high-speed (480Mbit/sec)
324 USB 2.0 device support. All CN6XXX based chips with USB are
325 supported.
326
327endif # USB_EHCI_HCD
328
329config USB_OXU210HP_HCD
330 tristate "OXU210HP HCD support"
331 depends on HAS_IOMEM
332 ---help---
333 The OXU210HP is an USB host/OTG/device controller. Enable this
334 option if your board has this chip. If unsure, say N.
335
336 This driver does not support isochronous transfers and doesn't
337 implement OTG nor USB device controllers.
338
339 To compile this driver as a module, choose M here: the
340 module will be called oxu210hp-hcd.
341
342config USB_ISP116X_HCD
343 tristate "ISP116X HCD support"
344 depends on HAS_IOMEM
345 ---help---
346 The ISP1160 and ISP1161 chips are USB host controllers. Enable this
347 option if your board has this chip. If unsure, say N.
348
349 This driver does not support isochronous transfers.
350
351 To compile this driver as a module, choose M here: the
352 module will be called isp116x-hcd.
353
354config USB_ISP1362_HCD
355 tristate "ISP1362 HCD support"
356 depends on HAS_IOMEM
357 ---help---
358 Supports the Philips ISP1362 chip as a host controller
359
360 This driver does not support isochronous transfers.
361
362 To compile this driver as a module, choose M here: the
363 module will be called isp1362-hcd.
364
365config USB_FOTG210_HCD
366 tristate "FOTG210 HCD support"
367 depends on USB && HAS_DMA && HAS_IOMEM
368 ---help---
369 Faraday FOTG210 is an OTG controller which can be configured as
370 an USB2.0 host. It is designed to meet USB2.0 EHCI specification
371 with minor modification.
372
373 To compile this driver as a module, choose M here: the
374 module will be called fotg210-hcd.
375
376config USB_MAX3421_HCD
377 tristate "MAX3421 HCD (USB-over-SPI) support"
378 depends on USB && SPI
379 ---help---
380 The Maxim MAX3421E chip supports standard USB 2.0-compliant
381 full-speed devices either in host or peripheral mode. This
382 driver supports the host-mode of the MAX3421E only.
383
384 To compile this driver as a module, choose M here: the module will
385 be called max3421-hcd.
386
387config USB_OHCI_HCD
388 tristate "OHCI HCD (USB 1.1) support"
389 depends on HAS_DMA && HAS_IOMEM
390 ---help---
391 The Open Host Controller Interface (OHCI) is a standard for accessing
392 USB 1.1 host controller hardware. It does more in hardware than Intel's
393 UHCI specification. If your USB host controller follows the OHCI spec,
394 say Y. On most non-x86 systems, and on x86 hardware that's not using a
395 USB controller from Intel or VIA, this is appropriate. If your host
396 controller doesn't use PCI, this is probably appropriate. For a PCI
397 based system where you're not sure, the "lspci -v" entry will list the
398 right "prog-if" for your USB controller(s): EHCI, OHCI, or UHCI.
399
400 To compile this driver as a module, choose M here: the
401 module will be called ohci-hcd.
402
403if USB_OHCI_HCD
404
405config USB_OHCI_HCD_OMAP1
406 tristate "OHCI support for OMAP1/2 chips"
407 depends on ARCH_OMAP1
408 depends on ISP1301_OMAP || !(MACH_OMAP_H2 || MACH_OMAP_H3)
409 default y
410 ---help---
411 Enables support for the OHCI controller on OMAP1/2 chips.
412
413config USB_OHCI_HCD_SPEAR
414 tristate "Support for ST SPEAr on-chip OHCI USB controller"
415 depends on USB_OHCI_HCD && PLAT_SPEAR
416 default y
417 ---help---
418 Enables support for the on-chip OHCI controller on
419 ST SPEAr chips.
420
421config USB_OHCI_HCD_STI
422 tristate "Support for ST STiHxxx on-chip OHCI USB controller"
423 depends on ARCH_STI && OF
424 select GENERIC_PHY
425 select USB_OHCI_HCD_PLATFORM
426 help
427 Enable support for the on-chip OHCI controller found on
428 STMicroelectronics consumer electronics SoC's.
429
430config USB_OHCI_HCD_S3C2410
431 tristate "OHCI support for Samsung S3C24xx/S3C64xx SoC series"
432 depends on USB_OHCI_HCD && (ARCH_S3C24XX || ARCH_S3C64XX)
433 default y
434 ---help---
435 Enables support for the on-chip OHCI controller on
436 S3C24xx/S3C64xx chips.
437
438config USB_OHCI_HCD_LPC32XX
439 tristate "Support for LPC on-chip OHCI USB controller"
440 depends on USB_OHCI_HCD && ARCH_LPC32XX
441 depends on USB_ISP1301
442 default y
443 ---help---
444 Enables support for the on-chip OHCI controller on
445 NXP chips.
446
447config USB_OHCI_HCD_PXA27X
448 tristate "Support for PXA27X/PXA3XX on-chip OHCI USB controller"
449 depends on USB_OHCI_HCD && (PXA27x || PXA3xx)
450 default y
451 ---help---
452 Enables support for the on-chip OHCI controller on
453 PXA27x/PXA3xx chips.
454
455config USB_OHCI_HCD_AT91
456 tristate "Support for Atmel on-chip OHCI USB controller"
457 depends on USB_OHCI_HCD && ARCH_AT91 && OF
458 default y
459 ---help---
460 Enables support for the on-chip OHCI controller on
461 Atmel chips.
462
463config USB_OHCI_HCD_OMAP3
464 tristate "OHCI support for OMAP3 and later chips"
465 depends on (ARCH_OMAP3 || ARCH_OMAP4)
466 default y
467 ---help---
468 Enables support for the on-chip OHCI controller on
469 OMAP3 and later chips.
470
471config USB_OHCI_HCD_DAVINCI
472 bool "OHCI support for TI DaVinci DA8xx"
473 depends on ARCH_DAVINCI_DA8XX
474 depends on USB_OHCI_HCD=y
475 default y
476 help
477 Enables support for the DaVinci DA8xx integrated OHCI
478 controller. This driver cannot currently be a loadable
479 module because it lacks a proper PHY abstraction.
480
481config USB_OHCI_ATH79
482 bool "USB OHCI support for the Atheros AR71XX/AR7240 SoCs (DEPRECATED)"
483 depends on (SOC_AR71XX || SOC_AR724X)
484 select USB_OHCI_HCD_PLATFORM
485 default y
486 help
487 This option is deprecated now and the driver was removed, use
488 USB_OHCI_HCD_PLATFORM instead.
489
490 Enables support for the built-in OHCI controller present on the
491 Atheros AR71XX/AR7240 SoCs.
492
493config USB_OHCI_HCD_PPC_OF_BE
494 bool "OHCI support for OF platform bus (big endian)"
495 depends on PPC
496 select USB_OHCI_BIG_ENDIAN_DESC
497 select USB_OHCI_BIG_ENDIAN_MMIO
498 ---help---
499 Enables support for big-endian USB controllers present on the
500 OpenFirmware platform bus.
501
502config USB_OHCI_HCD_PPC_OF_LE
503 bool "OHCI support for OF platform bus (little endian)"
504 depends on PPC
505 select USB_OHCI_LITTLE_ENDIAN
506 ---help---
507 Enables support for little-endian USB controllers present on the
508 OpenFirmware platform bus.
509
510config USB_OHCI_HCD_PPC_OF
511 bool
512 depends on PPC
513 default USB_OHCI_HCD_PPC_OF_BE || USB_OHCI_HCD_PPC_OF_LE
514
515config USB_OHCI_HCD_PCI
516 tristate "OHCI support for PCI-bus USB controllers"
517 depends on PCI
518 default y
519 select USB_OHCI_LITTLE_ENDIAN
520 ---help---
521 Enables support for PCI-bus plug-in USB controller cards.
522 If unsure, say Y.
523
524config USB_OHCI_HCD_SSB
525 bool "OHCI support for Broadcom SSB OHCI core (DEPRECATED)"
526 depends on (SSB = y || SSB = USB_OHCI_HCD)
527 select USB_HCD_SSB
528 select USB_OHCI_HCD_PLATFORM
529 default n
530 ---help---
531 This option is deprecated now and the driver was removed, use
532 USB_HCD_SSB and USB_OHCI_HCD_PLATFORM instead.
533
534 Support for the Sonics Silicon Backplane (SSB) attached
535 Broadcom USB OHCI core.
536
537 This device is present in some embedded devices with
538 Broadcom based SSB bus.
539
540 If unsure, say N.
541
542config USB_OHCI_SH
543 bool "OHCI support for SuperH USB controller (DEPRECATED)"
544 depends on SUPERH
545 select USB_OHCI_HCD_PLATFORM
546 ---help---
547 This option is deprecated now and the driver was removed, use
548 USB_OHCI_HCD_PLATFORM instead.
549
550 Enables support for the on-chip OHCI controller on the SuperH.
551 If you use the PCI OHCI controller, this option is not necessary.
552
553config USB_OHCI_EXYNOS
554 tristate "OHCI support for Samsung S5P/EXYNOS SoC Series"
555 depends on ARCH_S5PV210 || ARCH_EXYNOS
556 help
557 Enable support for the Samsung Exynos SOC's on-chip OHCI controller.
558
559config USB_CNS3XXX_OHCI
560 bool "Cavium CNS3XXX OHCI Module (DEPRECATED)"
561 depends on ARCH_CNS3XXX
562 select USB_OHCI_HCD_PLATFORM
563 ---help---
564 This option is deprecated now and the driver was removed, use
565 USB_OHCI_HCD_PLATFORM instead.
566
567 Enable support for the CNS3XXX SOC's on-chip OHCI controller.
568 It is needed for low-speed USB 1.0 device support.
569
570config USB_OHCI_HCD_PLATFORM
571 tristate "Generic OHCI driver for a platform device"
572 default n
573 ---help---
574 Adds an OHCI host driver for a generic platform device, which
575 provides a memory space and an irq.
576
577 If unsure, say N.
578
579config USB_OCTEON_OHCI
580 bool "Octeon on-chip OHCI support (DEPRECATED)"
581 depends on CAVIUM_OCTEON_SOC
582 default USB_OCTEON_EHCI
583 select USB_OHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
584 select USB_OHCI_LITTLE_ENDIAN
585 select USB_OHCI_HCD_PLATFORM
586 help
587 This option is deprecated now and the driver was removed, use
588 USB_OHCI_HCD_PLATFORM instead.
589
590 Enable support for the Octeon II SOC's on-chip OHCI
591 controller. It is needed for low-speed USB 1.0 device
592 support. All CN6XXX based chips with USB are supported.
593
594endif # USB_OHCI_HCD
595
596config USB_UHCI_HCD
597 tristate "UHCI HCD (most Intel and VIA) support"
598 depends on PCI || USB_UHCI_SUPPORT_NON_PCI_HC
599 ---help---
600 The Universal Host Controller Interface is a standard by Intel for
601 accessing the USB hardware in the PC (which is also called the USB
602 host controller). If your USB host controller conforms to this
603 standard, you may want to say Y, but see below. All recent boards
604 with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX,
605 i810, i820) conform to this standard. Also all VIA PCI chipsets
606 (like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro
607 133) and LEON/GRLIB SoCs with the GRUSBHC controller.
608 If unsure, say Y.
609
610 To compile this driver as a module, choose M here: the
611 module will be called uhci-hcd.
612
613config USB_UHCI_SUPPORT_NON_PCI_HC
614 bool
615 default y if (SPARC_LEON || USB_UHCI_PLATFORM)
616
617config USB_UHCI_PLATFORM
618 bool
619 default y if ARCH_VT8500
620
621config USB_UHCI_BIG_ENDIAN_MMIO
622 bool
623 default y if SPARC_LEON
624
625config USB_UHCI_BIG_ENDIAN_DESC
626 bool
627 default y if SPARC_LEON
628
629config USB_FHCI_HCD
630 tristate "Freescale QE USB Host Controller support"
631 depends on OF_GPIO && QE_GPIO && QUICC_ENGINE
632 select FSL_GTM
633 select QE_USB
634 help
635 This driver enables support for Freescale QE USB Host Controller
636 (as found on MPC8360 and MPC8323 processors), the driver supports
637 Full and Low Speed USB.
638
639config FHCI_DEBUG
640 bool "Freescale QE USB Host Controller debug support"
641 depends on USB_FHCI_HCD && DEBUG_FS
642 help
643 Say "y" to see some FHCI debug information and statistics
644 through debugfs.
645
646config USB_U132_HCD
647 tristate "Elan U132 Adapter Host Controller"
648 depends on USB_FTDI_ELAN
649 help
650 The U132 adapter is a USB to CardBus adapter specifically designed
651 for PC cards that contain an OHCI host controller. Typical PC cards
652 are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132
653 adapter will *NOT* work with PC cards that do not contain an OHCI
654 controller.
655
656 For those PC cards that contain multiple OHCI controllers only the
657 first one is used.
658
659 The driver consists of two modules, the "ftdi-elan" module is a
660 USB client driver that interfaces to the FTDI chip within ELAN's
661 USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host
662 controller driver that talks to the OHCI controller within the
663 CardBus cards that are inserted in the U132 adapter.
664
665 This driver has been tested with a CardBus OHCI USB adapter, and
666 worked with a USB PEN Drive inserted into the first USB port of
667 the PCCARD. A rather pointless thing to do, but useful for testing.
668
669 It is safe to say M here.
670
671 See also <http://www.elandigitalsystems.com/support/ufaq/u132linux.php>
672
673config USB_SL811_HCD
674 tristate "SL811HS HCD support"
675 depends on HAS_IOMEM
676 help
677 The SL811HS is a single-port USB controller that supports either
678 host side or peripheral side roles. Enable this option if your
679 board has this chip, and you want to use it as a host controller.
680 If unsure, say N.
681
682 To compile this driver as a module, choose M here: the
683 module will be called sl811-hcd.
684
685config USB_SL811_HCD_ISO
686 bool "partial ISO support"
687 depends on USB_SL811_HCD
688 help
689 The driver doesn't support iso_frame_desc (yet), but for some simple
690 devices that just queue one ISO frame per URB, then ISO transfers
691 "should" work using the normal urb status fields.
692
693 If unsure, say N.
694
695config USB_SL811_CS
696 tristate "CF/PCMCIA support for SL811HS HCD"
697 depends on USB_SL811_HCD && PCMCIA
698 help
699 Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC
700 REX-CFU1U CF card (often used with PDAs). If unsure, say N.
701
702 To compile this driver as a module, choose M here: the
703 module will be called "sl811_cs".
704
705config USB_R8A66597_HCD
706 tristate "R8A66597 HCD support"
707 depends on HAS_IOMEM
708 help
709 The R8A66597 is a USB 2.0 host and peripheral controller.
710
711 Enable this option if your board has this chip, and you want
712 to use it as a host controller. If unsure, say N.
713
714 To compile this driver as a module, choose M here: the
715 module will be called r8a66597-hcd.
716
717config USB_RENESAS_USBHS_HCD
718 tristate "Renesas USBHS HCD support"
719 depends on USB_RENESAS_USBHS
720 help
721 The Renesas USBHS is a USB 2.0 host and peripheral controller.
722
723 Enable this option if your board has this chip, and you want
724 to use it as a host controller. If unsure, say N.
725
726 To compile this driver as a module, choose M here: the
727 module will be called renesas-usbhs.
728
729config USB_WHCI_HCD
730 tristate "Wireless USB Host Controller Interface (WHCI) driver"
731 depends on PCI && USB && UWB
732 select USB_WUSB
733 select UWB_WHCI
734 help
735 A driver for PCI-based Wireless USB Host Controllers that are
736 compliant with the WHCI specification.
737
738 To compile this driver a module, choose M here: the module
739 will be called "whci-hcd".
740
741config USB_HWA_HCD
742 tristate "Host Wire Adapter (HWA) driver"
743 depends on USB && UWB
744 select USB_WUSB
745 select UWB_HWA
746 help
747 This driver enables you to connect Wireless USB devices to
748 your system using a Host Wire Adaptor USB dongle. This is an
749 UWB Radio Controller and WUSB Host Controller connected to
750 your machine via USB (specified in WUSB1.0).
751
752 To compile this driver a module, choose M here: the module
753 will be called "hwa-hc".
754
755config USB_IMX21_HCD
756 tristate "i.MX21 HCD support"
757 depends on ARM && ARCH_MXC
758 help
759 This driver enables support for the on-chip USB host in the
760 i.MX21 processor.
761
762 To compile this driver as a module, choose M here: the
763 module will be called "imx21-hcd".
764
765config USB_HCD_BCMA
766 tristate "BCMA usb host driver"
767 depends on BCMA
768 select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
769 select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
770 help
771 Enable support for the EHCI and OCHI host controller on an bcma bus.
772 It converts the bcma driver into two platform device drivers
773 for ehci and ohci.
774
775 If unsure, say N.
776
777config USB_HCD_SSB
778 tristate "SSB usb host driver"
779 depends on SSB
780 select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
781 select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
782 help
783 Enable support for the EHCI and OCHI host controller on an bcma bus.
784 It converts the bcma driver into two platform device drivers
785 for ehci and ohci.
786
787 If unsure, say N.
788
789config USB_HCD_TEST_MODE
790 bool "HCD test mode support"
791 ---help---
792 Say 'Y' to enable additional software test modes that may be
793 supported by the host controller drivers.
794
795 One such test mode is the Embedded High-speed Host Electrical Test
796 (EHSET) for EHCI host controller hardware, specifically the "Single
797 Step Set Feature" test. Typically this will be enabled for On-the-Go
798 or embedded hosts that need to undergo USB-IF compliance testing with
799 the aid of special testing hardware. In the future, this may expand
800 to include other tests that require support from a HCD driver.
801
802 This option is of interest only to developers who need to validate
803 their USB hardware designs. It is not needed for normal use. If
804 unsure, say N.
1#
2# USB Host Controller Drivers
3#
4comment "USB Host Controller Drivers"
5
6config USB_C67X00_HCD
7 tristate "Cypress C67x00 HCD support"
8 help
9 The Cypress C67x00 (EZ-Host/EZ-OTG) chips are dual-role
10 host/peripheral/OTG USB controllers.
11
12 Enable this option to support this chip in host controller mode.
13 If unsure, say N.
14
15 To compile this driver as a module, choose M here: the
16 module will be called c67x00.
17
18config USB_XHCI_HCD
19 tristate "xHCI HCD (USB 3.0) support"
20 ---help---
21 The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0
22 "SuperSpeed" host controller hardware.
23
24 To compile this driver as a module, choose M here: the
25 module will be called xhci-hcd.
26
27if USB_XHCI_HCD
28
29config USB_XHCI_PLATFORM
30 tristate
31
32endif # USB_XHCI_HCD
33
34config USB_EHCI_HCD
35 tristate "EHCI HCD (USB 2.0) support"
36 ---help---
37 The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
38 "high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
39 If your USB host controller supports USB 2.0, you will likely want to
40 configure this Host Controller Driver.
41
42 EHCI controllers are packaged with "companion" host controllers (OHCI
43 or UHCI) to handle USB 1.1 devices connected to root hub ports. Ports
44 will connect to EHCI if the device is high speed, otherwise they
45 connect to a companion controller. If you configure EHCI, you should
46 probably configure the OHCI (for NEC and some other vendors) USB Host
47 Controller Driver or UHCI (for Via motherboards) Host Controller
48 Driver too.
49
50 You may want to read <file:Documentation/usb/ehci.txt>.
51
52 To compile this driver as a module, choose M here: the
53 module will be called ehci-hcd.
54
55config USB_EHCI_ROOT_HUB_TT
56 bool "Root Hub Transaction Translators"
57 depends on USB_EHCI_HCD
58 ---help---
59 Some EHCI chips have vendor-specific extensions to integrate
60 transaction translators, so that no OHCI or UHCI companion
61 controller is needed. It's safe to say "y" even if your
62 controller doesn't support this feature.
63
64 This supports the EHCI implementation that's originally
65 from ARC, and has since changed hands a few times.
66
67config USB_EHCI_TT_NEWSCHED
68 bool "Improved Transaction Translator scheduling"
69 depends on USB_EHCI_HCD
70 default y
71 ---help---
72 This changes the periodic scheduling code to fill more of the low
73 and full speed bandwidth available from the Transaction Translator
74 (TT) in USB 2.0 hubs. Without this, only one transfer will be
75 issued in each microframe, significantly reducing the number of
76 periodic low/fullspeed transfers possible.
77
78 If you have multiple periodic low/fullspeed devices connected to a
79 highspeed USB hub which is connected to a highspeed USB Host
80 Controller, and some of those devices will not work correctly
81 (possibly due to "ENOSPC" or "-28" errors), say Y. Conversely, if
82 you have only one such device and it doesn't work, you could try
83 saying N.
84
85 If unsure, say Y.
86
87config USB_FSL_MPH_DR_OF
88 tristate
89
90if USB_EHCI_HCD
91
92config USB_EHCI_PCI
93 tristate
94 depends on PCI
95 default y
96
97config USB_EHCI_HCD_PMC_MSP
98 tristate "EHCI support for on-chip PMC MSP71xx USB controller"
99 depends on MSP_HAS_USB
100 default n
101 select USB_EHCI_BIG_ENDIAN_DESC
102 select USB_EHCI_BIG_ENDIAN_MMIO
103 ---help---
104 Enables support for the onchip USB controller on the PMC_MSP7100 Family SoC's.
105 If unsure, say N.
106
107config XPS_USB_HCD_XILINX
108 bool "Use Xilinx usb host EHCI controller core"
109 depends on (PPC32 || MICROBLAZE)
110 select USB_EHCI_BIG_ENDIAN_DESC
111 select USB_EHCI_BIG_ENDIAN_MMIO
112 ---help---
113 Xilinx xps USB host controller core is EHCI compilant and has
114 transaction translator built-in. It can be configured to either
115 support both high speed and full speed devices, or high speed
116 devices only.
117
118config USB_EHCI_FSL
119 bool "Support for Freescale PPC on-chip EHCI USB controller"
120 depends on FSL_SOC
121 select USB_EHCI_ROOT_HUB_TT
122 select USB_FSL_MPH_DR_OF if OF
123 ---help---
124 Variation of ARC USB block used in some Freescale chips.
125
126config USB_EHCI_MXC
127 tristate "Support for Freescale i.MX on-chip EHCI USB controller"
128 depends on ARCH_MXC
129 select USB_EHCI_ROOT_HUB_TT
130 ---help---
131 Variation of ARC USB block used in some Freescale chips.
132
133config USB_EHCI_HCD_OMAP
134 tristate "EHCI support for OMAP3 and later chips"
135 depends on ARCH_OMAP
136 select NOP_USB_XCEIV
137 default y
138 ---help---
139 Enables support for the on-chip EHCI controller on
140 OMAP3 and later chips.
141
142config USB_EHCI_HCD_ORION
143 tristate "Support for Marvell EBU on-chip EHCI USB controller"
144 depends on USB_EHCI_HCD && PLAT_ORION
145 default y
146 ---help---
147 Enables support for the on-chip EHCI controller on Marvell's
148 embedded ARM SoCs, including Orion, Kirkwood, Dove, Armada XP,
149 Armada 370. This is different from the EHCI implementation
150 on Marvell's mobile PXA and MMP SoC, see "EHCI support for
151 Marvell PXA/MMP USB controller" for those.
152
153config USB_EHCI_HCD_SPEAR
154 tristate "Support for ST SPEAr on-chip EHCI USB controller"
155 depends on USB_EHCI_HCD && PLAT_SPEAR
156 default y
157 ---help---
158 Enables support for the on-chip EHCI controller on
159 ST SPEAr chips.
160
161config USB_EHCI_HCD_AT91
162 tristate "Support for Atmel on-chip EHCI USB controller"
163 depends on USB_EHCI_HCD && ARCH_AT91
164 default y
165 ---help---
166 Enables support for the on-chip EHCI controller on
167 Atmel chips.
168
169config USB_EHCI_MSM
170 tristate "Support for Qualcomm QSD/MSM on-chip EHCI USB controller"
171 depends on ARCH_MSM
172 select USB_EHCI_ROOT_HUB_TT
173 select USB_MSM_OTG
174 ---help---
175 Enables support for the USB Host controller present on the
176 Qualcomm chipsets. Root Hub has inbuilt TT.
177 This driver depends on OTG driver for PHY initialization,
178 clock management, powering up VBUS, and power management.
179 This driver is not supported on boards like trout which
180 has an external PHY.
181
182config USB_EHCI_TEGRA
183 tristate "NVIDIA Tegra HCD support"
184 depends on ARCH_TEGRA
185 select USB_EHCI_ROOT_HUB_TT
186 select USB_PHY
187 help
188 This driver enables support for the internal USB Host Controllers
189 found in NVIDIA Tegra SoCs. The controllers are EHCI compliant.
190
191config USB_EHCI_HCD_PPC_OF
192 bool "EHCI support for PPC USB controller on OF platform bus"
193 depends on PPC_OF
194 default y
195 ---help---
196 Enables support for the USB controller present on the PowerPC
197 OpenFirmware platform bus.
198
199config USB_EHCI_SH
200 bool "EHCI support for SuperH USB controller"
201 depends on SUPERH
202 ---help---
203 Enables support for the on-chip EHCI controller on the SuperH.
204 If you use the PCI EHCI controller, this option is not necessary.
205
206config USB_EHCI_EXYNOS
207 tristate "EHCI support for Samsung S5P/EXYNOS SoC Series"
208 depends on PLAT_S5P || ARCH_EXYNOS
209 help
210 Enable support for the Samsung Exynos SOC's on-chip EHCI controller.
211
212config USB_EHCI_MV
213 bool "EHCI support for Marvell PXA/MMP USB controller"
214 depends on (ARCH_PXA || ARCH_MMP)
215 select USB_EHCI_ROOT_HUB_TT
216 ---help---
217 Enables support for Marvell (including PXA and MMP series) on-chip
218 USB SPH and OTG controller. SPH is a single port host, and it can
219 only be EHCI host. OTG is controller that can switch to host mode.
220 Note that this driver will not work on Marvell's other EHCI
221 controller used by the EBU-type SoCs including Orion, Kirkwood,
222 Dova, Armada 370 and Armada XP. See "Support for Marvell EBU
223 on-chip EHCI USB controller" for those.
224
225config USB_W90X900_EHCI
226 tristate "W90X900(W90P910) EHCI support"
227 depends on ARCH_W90X900
228 ---help---
229 Enables support for the W90X900 USB controller
230
231config USB_CNS3XXX_EHCI
232 bool "Cavium CNS3XXX EHCI Module (DEPRECATED)"
233 depends on ARCH_CNS3XXX
234 select USB_EHCI_HCD_PLATFORM
235 ---help---
236 This option is deprecated now and the driver was removed, use
237 USB_EHCI_HCD_PLATFORM instead.
238
239 Enable support for the CNS3XXX SOC's on-chip EHCI controller.
240 It is needed for high-speed (480Mbit/sec) USB 2.0 device
241 support.
242
243config USB_EHCI_ATH79
244 bool "EHCI support for AR7XXX/AR9XXX SoCs (DEPRECATED)"
245 depends on (SOC_AR71XX || SOC_AR724X || SOC_AR913X || SOC_AR933X)
246 select USB_EHCI_ROOT_HUB_TT
247 select USB_EHCI_HCD_PLATFORM
248 default y
249 ---help---
250 This option is deprecated now and the driver was removed, use
251 USB_EHCI_HCD_PLATFORM instead.
252
253 Enables support for the built-in EHCI controller present
254 on the Atheros AR7XXX/AR9XXX SoCs.
255
256config USB_EHCI_HCD_PLATFORM
257 tristate "Generic EHCI driver for a platform device"
258 default n
259 ---help---
260 Adds an EHCI host driver for a generic platform device, which
261 provides a memory space and an irq.
262
263 If unsure, say N.
264
265config USB_OCTEON_EHCI
266 bool "Octeon on-chip EHCI support"
267 depends on CAVIUM_OCTEON_SOC
268 default n
269 select USB_EHCI_BIG_ENDIAN_MMIO
270 help
271 Enable support for the Octeon II SOC's on-chip EHCI
272 controller. It is needed for high-speed (480Mbit/sec)
273 USB 2.0 device support. All CN6XXX based chips with USB are
274 supported.
275
276endif # USB_EHCI_HCD
277
278config USB_OXU210HP_HCD
279 tristate "OXU210HP HCD support"
280 ---help---
281 The OXU210HP is an USB host/OTG/device controller. Enable this
282 option if your board has this chip. If unsure, say N.
283
284 This driver does not support isochronous transfers and doesn't
285 implement OTG nor USB device controllers.
286
287 To compile this driver as a module, choose M here: the
288 module will be called oxu210hp-hcd.
289
290config USB_ISP116X_HCD
291 tristate "ISP116X HCD support"
292 ---help---
293 The ISP1160 and ISP1161 chips are USB host controllers. Enable this
294 option if your board has this chip. If unsure, say N.
295
296 This driver does not support isochronous transfers.
297
298 To compile this driver as a module, choose M here: the
299 module will be called isp116x-hcd.
300
301config USB_ISP1760_HCD
302 tristate "ISP 1760 HCD support"
303 ---help---
304 The ISP1760 chip is a USB 2.0 host controller.
305
306 This driver does not support isochronous transfers or OTG.
307 This USB controller is usually attached to a non-DMA-Master
308 capable bus. NXP's eval kit brings this chip on PCI card
309 where the chip itself is behind a PLB to simulate such
310 a bus.
311
312 To compile this driver as a module, choose M here: the
313 module will be called isp1760.
314
315config USB_ISP1362_HCD
316 tristate "ISP1362 HCD support"
317 ---help---
318 Supports the Philips ISP1362 chip as a host controller
319
320 This driver does not support isochronous transfers.
321
322 To compile this driver as a module, choose M here: the
323 module will be called isp1362-hcd.
324
325config USB_FUSBH200_HCD
326 tristate "FUSBH200 HCD support"
327 depends on USB
328 ---help---
329 Faraday FUSBH200 is designed to meet USB2.0 EHCI specification
330 with minor modification.
331
332 To compile this driver as a module, choose M here: the
333 module will be called fusbh200-hcd.
334
335config USB_FOTG210_HCD
336 tristate "FOTG210 HCD support"
337 depends on USB
338 ---help---
339 Faraday FOTG210 is an OTG controller which can be configured as
340 an USB2.0 host. It is designed to meet USB2.0 EHCI specification
341 with minor modification.
342
343 To compile this driver as a module, choose M here: the
344 module will be called fotg210-hcd.
345
346config USB_OHCI_HCD
347 tristate "OHCI HCD (USB 1.1) support"
348 select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3
349 depends on USB_ISP1301 || !ARCH_LPC32XX
350 ---help---
351 The Open Host Controller Interface (OHCI) is a standard for accessing
352 USB 1.1 host controller hardware. It does more in hardware than Intel's
353 UHCI specification. If your USB host controller follows the OHCI spec,
354 say Y. On most non-x86 systems, and on x86 hardware that's not using a
355 USB controller from Intel or VIA, this is appropriate. If your host
356 controller doesn't use PCI, this is probably appropriate. For a PCI
357 based system where you're not sure, the "lspci -v" entry will list the
358 right "prog-if" for your USB controller(s): EHCI, OHCI, or UHCI.
359
360 To compile this driver as a module, choose M here: the
361 module will be called ohci-hcd.
362
363if USB_OHCI_HCD
364
365config USB_OHCI_HCD_OMAP1
366 tristate "OHCI support for OMAP1/2 chips"
367 depends on ARCH_OMAP1
368 default y
369 ---help---
370 Enables support for the OHCI controller on OMAP1/2 chips.
371
372config USB_OHCI_HCD_SPEAR
373 tristate "Support for ST SPEAr on-chip OHCI USB controller"
374 depends on USB_OHCI_HCD && PLAT_SPEAR
375 default y
376 ---help---
377 Enables support for the on-chip OHCI controller on
378 ST SPEAr chips.
379
380config USB_OHCI_HCD_S3C2410
381 tristate "OHCI support for Samsung S3C24xx/S3C64xx SoC series"
382 depends on USB_OHCI_HCD && (ARCH_S3C24XX || ARCH_S3C64XX)
383 default y
384 ---help---
385 Enables support for the on-chip OHCI controller on
386 S3C24xx/S3C64xx chips.
387
388config USB_OHCI_HCD_LPC32XX
389 tristate "Support for LPC on-chip OHCI USB controller"
390 depends on USB_OHCI_HCD && ARCH_LPC32XX
391 default y
392 ---help---
393 Enables support for the on-chip OHCI controller on
394 NXP chips.
395
396config USB_OHCI_HCD_PXA27X
397 tristate "Support for PXA27X/PXA3XX on-chip OHCI USB controller"
398 depends on USB_OHCI_HCD && (PXA27x || PXA3xx)
399 default y
400 ---help---
401 Enables support for the on-chip OHCI controller on
402 PXA27x/PXA3xx chips.
403
404config USB_OHCI_HCD_AT91
405 tristate "Support for Atmel on-chip OHCI USB controller"
406 depends on USB_OHCI_HCD && ARCH_AT91
407 default y
408 ---help---
409 Enables support for the on-chip OHCI controller on
410 Atmel chips.
411
412config USB_OHCI_HCD_OMAP3
413 tristate "OHCI support for OMAP3 and later chips"
414 depends on (ARCH_OMAP3 || ARCH_OMAP4)
415 default y
416 ---help---
417 Enables support for the on-chip OHCI controller on
418 OMAP3 and later chips.
419
420config USB_OHCI_ATH79
421 bool "USB OHCI support for the Atheros AR71XX/AR7240 SoCs (DEPRECATED)"
422 depends on (SOC_AR71XX || SOC_AR724X)
423 select USB_OHCI_HCD_PLATFORM
424 default y
425 help
426 This option is deprecated now and the driver was removed, use
427 USB_OHCI_HCD_PLATFORM instead.
428
429 Enables support for the built-in OHCI controller present on the
430 Atheros AR71XX/AR7240 SoCs.
431
432config USB_OHCI_HCD_PPC_OF_BE
433 bool "OHCI support for OF platform bus (big endian)"
434 depends on PPC_OF
435 select USB_OHCI_BIG_ENDIAN_DESC
436 select USB_OHCI_BIG_ENDIAN_MMIO
437 ---help---
438 Enables support for big-endian USB controllers present on the
439 OpenFirmware platform bus.
440
441config USB_OHCI_HCD_PPC_OF_LE
442 bool "OHCI support for OF platform bus (little endian)"
443 depends on PPC_OF
444 select USB_OHCI_LITTLE_ENDIAN
445 ---help---
446 Enables support for little-endian USB controllers present on the
447 OpenFirmware platform bus.
448
449config USB_OHCI_HCD_PPC_OF
450 bool
451 depends on PPC_OF
452 default USB_OHCI_HCD_PPC_OF_BE || USB_OHCI_HCD_PPC_OF_LE
453
454config USB_OHCI_HCD_PCI
455 tristate "OHCI support for PCI-bus USB controllers"
456 depends on PCI
457 default y
458 select USB_OHCI_LITTLE_ENDIAN
459 ---help---
460 Enables support for PCI-bus plug-in USB controller cards.
461 If unsure, say Y.
462
463config USB_OHCI_HCD_SSB
464 bool "OHCI support for Broadcom SSB OHCI core (DEPRECATED)"
465 depends on (SSB = y || SSB = USB_OHCI_HCD)
466 select USB_HCD_SSB
467 select USB_OHCI_HCD_PLATFORM
468 default n
469 ---help---
470 This option is deprecated now and the driver was removed, use
471 USB_HCD_SSB and USB_OHCI_HCD_PLATFORM instead.
472
473 Support for the Sonics Silicon Backplane (SSB) attached
474 Broadcom USB OHCI core.
475
476 This device is present in some embedded devices with
477 Broadcom based SSB bus.
478
479 If unsure, say N.
480
481config USB_OHCI_SH
482 bool "OHCI support for SuperH USB controller (DEPRECATED)"
483 depends on SUPERH
484 select USB_OHCI_HCD_PLATFORM
485 ---help---
486 This option is deprecated now and the driver was removed, use
487 USB_OHCI_HCD_PLATFORM instead.
488
489 Enables support for the on-chip OHCI controller on the SuperH.
490 If you use the PCI OHCI controller, this option is not necessary.
491
492config USB_OHCI_EXYNOS
493 tristate "OHCI support for Samsung S5P/EXYNOS SoC Series"
494 depends on PLAT_S5P || ARCH_EXYNOS
495 help
496 Enable support for the Samsung Exynos SOC's on-chip OHCI controller.
497
498config USB_CNS3XXX_OHCI
499 bool "Cavium CNS3XXX OHCI Module (DEPRECATED)"
500 depends on ARCH_CNS3XXX
501 select USB_OHCI_HCD_PLATFORM
502 ---help---
503 This option is deprecated now and the driver was removed, use
504 USB_OHCI_HCD_PLATFORM instead.
505
506 Enable support for the CNS3XXX SOC's on-chip OHCI controller.
507 It is needed for low-speed USB 1.0 device support.
508
509config USB_OHCI_HCD_PLATFORM
510 tristate "Generic OHCI driver for a platform device"
511 default n
512 ---help---
513 Adds an OHCI host driver for a generic platform device, which
514 provides a memory space and an irq.
515
516 If unsure, say N.
517
518config USB_OCTEON_OHCI
519 bool "Octeon on-chip OHCI support"
520 depends on CAVIUM_OCTEON_SOC
521 default USB_OCTEON_EHCI
522 select USB_OHCI_BIG_ENDIAN_MMIO
523 select USB_OHCI_LITTLE_ENDIAN
524 help
525 Enable support for the Octeon II SOC's on-chip OHCI
526 controller. It is needed for low-speed USB 1.0 device
527 support. All CN6XXX based chips with USB are supported.
528
529endif # USB_OHCI_HCD
530
531config USB_UHCI_HCD
532 tristate "UHCI HCD (most Intel and VIA) support"
533 depends on PCI || USB_UHCI_SUPPORT_NON_PCI_HC
534 ---help---
535 The Universal Host Controller Interface is a standard by Intel for
536 accessing the USB hardware in the PC (which is also called the USB
537 host controller). If your USB host controller conforms to this
538 standard, you may want to say Y, but see below. All recent boards
539 with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX,
540 i810, i820) conform to this standard. Also all VIA PCI chipsets
541 (like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro
542 133) and LEON/GRLIB SoCs with the GRUSBHC controller.
543 If unsure, say Y.
544
545 To compile this driver as a module, choose M here: the
546 module will be called uhci-hcd.
547
548config USB_UHCI_SUPPORT_NON_PCI_HC
549 bool
550 default y if (SPARC_LEON || USB_UHCI_PLATFORM)
551
552config USB_UHCI_PLATFORM
553 bool
554 default y if ARCH_VT8500
555
556config USB_UHCI_BIG_ENDIAN_MMIO
557 bool
558 default y if SPARC_LEON
559
560config USB_UHCI_BIG_ENDIAN_DESC
561 bool
562 default y if SPARC_LEON
563
564config USB_FHCI_HCD
565 tristate "Freescale QE USB Host Controller support"
566 depends on OF_GPIO && QE_GPIO && QUICC_ENGINE
567 select FSL_GTM
568 select QE_USB
569 help
570 This driver enables support for Freescale QE USB Host Controller
571 (as found on MPC8360 and MPC8323 processors), the driver supports
572 Full and Low Speed USB.
573
574config FHCI_DEBUG
575 bool "Freescale QE USB Host Controller debug support"
576 depends on USB_FHCI_HCD && DEBUG_FS
577 help
578 Say "y" to see some FHCI debug information and statistics
579 through debugfs.
580
581config USB_U132_HCD
582 tristate "Elan U132 Adapter Host Controller"
583 depends on USB_FTDI_ELAN
584 help
585 The U132 adapter is a USB to CardBus adapter specifically designed
586 for PC cards that contain an OHCI host controller. Typical PC cards
587 are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132
588 adapter will *NOT* work with PC cards that do not contain an OHCI
589 controller.
590
591 For those PC cards that contain multiple OHCI controllers only the
592 first one is used.
593
594 The driver consists of two modules, the "ftdi-elan" module is a
595 USB client driver that interfaces to the FTDI chip within ELAN's
596 USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host
597 controller driver that talks to the OHCI controller within the
598 CardBus cards that are inserted in the U132 adapter.
599
600 This driver has been tested with a CardBus OHCI USB adapter, and
601 worked with a USB PEN Drive inserted into the first USB port of
602 the PCCARD. A rather pointless thing to do, but useful for testing.
603
604 It is safe to say M here.
605
606 See also <http://www.elandigitalsystems.com/support/ufaq/u132linux.php>
607
608config USB_SL811_HCD
609 tristate "SL811HS HCD support"
610 help
611 The SL811HS is a single-port USB controller that supports either
612 host side or peripheral side roles. Enable this option if your
613 board has this chip, and you want to use it as a host controller.
614 If unsure, say N.
615
616 To compile this driver as a module, choose M here: the
617 module will be called sl811-hcd.
618
619config USB_SL811_HCD_ISO
620 bool "partial ISO support"
621 depends on USB_SL811_HCD
622 help
623 The driver doesn't support iso_frame_desc (yet), but for some simple
624 devices that just queue one ISO frame per URB, then ISO transfers
625 "should" work using the normal urb status fields.
626
627 If unsure, say N.
628
629config USB_SL811_CS
630 tristate "CF/PCMCIA support for SL811HS HCD"
631 depends on USB_SL811_HCD && PCMCIA
632 help
633 Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC
634 REX-CFU1U CF card (often used with PDAs). If unsure, say N.
635
636 To compile this driver as a module, choose M here: the
637 module will be called "sl811_cs".
638
639config USB_R8A66597_HCD
640 tristate "R8A66597 HCD support"
641 help
642 The R8A66597 is a USB 2.0 host and peripheral controller.
643
644 Enable this option if your board has this chip, and you want
645 to use it as a host controller. If unsure, say N.
646
647 To compile this driver as a module, choose M here: the
648 module will be called r8a66597-hcd.
649
650config USB_RENESAS_USBHS_HCD
651 tristate "Renesas USBHS HCD support"
652 depends on USB_RENESAS_USBHS
653 help
654 The Renesas USBHS is a USB 2.0 host and peripheral controller.
655
656 Enable this option if your board has this chip, and you want
657 to use it as a host controller. If unsure, say N.
658
659 To compile this driver as a module, choose M here: the
660 module will be called renesas-usbhs.
661
662config USB_WHCI_HCD
663 tristate "Wireless USB Host Controller Interface (WHCI) driver"
664 depends on PCI && USB && UWB
665 select USB_WUSB
666 select UWB_WHCI
667 help
668 A driver for PCI-based Wireless USB Host Controllers that are
669 compliant with the WHCI specification.
670
671 To compile this driver a module, choose M here: the module
672 will be called "whci-hcd".
673
674config USB_HWA_HCD
675 tristate "Host Wire Adapter (HWA) driver"
676 depends on UWB
677 select USB_WUSB
678 select UWB_HWA
679 help
680 This driver enables you to connect Wireless USB devices to
681 your system using a Host Wire Adaptor USB dongle. This is an
682 UWB Radio Controller and WUSB Host Controller connected to
683 your machine via USB (specified in WUSB1.0).
684
685 To compile this driver a module, choose M here: the module
686 will be called "hwa-hc".
687
688config USB_IMX21_HCD
689 tristate "i.MX21 HCD support"
690 depends on ARM && ARCH_MXC
691 help
692 This driver enables support for the on-chip USB host in the
693 i.MX21 processor.
694
695 To compile this driver as a module, choose M here: the
696 module will be called "imx21-hcd".
697
698
699
700config USB_OCTEON2_COMMON
701 bool
702 default y if USB_OCTEON_EHCI || USB_OCTEON_OHCI
703
704config USB_HCD_BCMA
705 tristate "BCMA usb host driver"
706 depends on BCMA
707 select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
708 select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
709 help
710 Enable support for the EHCI and OCHI host controller on an bcma bus.
711 It converts the bcma driver into two platform device drivers
712 for ehci and ohci.
713
714 If unsure, say N.
715
716config USB_HCD_SSB
717 tristate "SSB usb host driver"
718 depends on SSB
719 select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
720 select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
721 help
722 Enable support for the EHCI and OCHI host controller on an bcma bus.
723 It converts the bcma driver into two platform device drivers
724 for ehci and ohci.
725
726 If unsure, say N.
727
728config USB_HCD_TEST_MODE
729 bool "HCD test mode support"
730 ---help---
731 Say 'Y' to enable additional software test modes that may be
732 supported by the host controller drivers.
733
734 One such test mode is the Embedded High-speed Host Electrical Test
735 (EHSET) for EHCI host controller hardware, specifically the "Single
736 Step Set Feature" test. Typically this will be enabled for On-the-Go
737 or embedded hosts that need to undergo USB-IF compliance testing with
738 the aid of special testing hardware. In the future, this may expand
739 to include other tests that require support from a HCD driver.
740
741 This option is of interest only to developers who need to validate
742 their USB hardware designs. It is not needed for normal use. If
743 unsure, say N.