Loading...
1/*
2 * Silicon Laboratories CP210x USB to RS232 serial adaptor driver
3 *
4 * Copyright (C) 2005 Craig Shelley (craig@microtron.org.uk)
5 *
6 * This program is free software; you can redistribute it and/or
7 * modify it under the terms of the GNU General Public License version
8 * 2 as published by the Free Software Foundation.
9 *
10 * Support to set flow control line levels using TIOCMGET and TIOCMSET
11 * thanks to Karl Hiramoto karl@hiramoto.org. RTSCTS hardware flow
12 * control thanks to Munir Nassar nassarmu@real-time.com
13 *
14 */
15
16#include <linux/kernel.h>
17#include <linux/errno.h>
18#include <linux/slab.h>
19#include <linux/tty.h>
20#include <linux/tty_flip.h>
21#include <linux/module.h>
22#include <linux/moduleparam.h>
23#include <linux/usb.h>
24#include <linux/uaccess.h>
25#include <linux/usb/serial.h>
26
27#define DRIVER_DESC "Silicon Labs CP210x RS232 serial adaptor driver"
28
29/*
30 * Function Prototypes
31 */
32static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *);
33static void cp210x_close(struct usb_serial_port *);
34static void cp210x_get_termios(struct tty_struct *, struct usb_serial_port *);
35static void cp210x_get_termios_port(struct usb_serial_port *port,
36 unsigned int *cflagp, unsigned int *baudp);
37static void cp210x_change_speed(struct tty_struct *, struct usb_serial_port *,
38 struct ktermios *);
39static void cp210x_set_termios(struct tty_struct *, struct usb_serial_port *,
40 struct ktermios*);
41static bool cp210x_tx_empty(struct usb_serial_port *port);
42static int cp210x_tiocmget(struct tty_struct *);
43static int cp210x_tiocmset(struct tty_struct *, unsigned int, unsigned int);
44static int cp210x_tiocmset_port(struct usb_serial_port *port,
45 unsigned int, unsigned int);
46static void cp210x_break_ctl(struct tty_struct *, int);
47static int cp210x_port_probe(struct usb_serial_port *);
48static int cp210x_port_remove(struct usb_serial_port *);
49static void cp210x_dtr_rts(struct usb_serial_port *p, int on);
50
51static const struct usb_device_id id_table[] = {
52 { USB_DEVICE(0x045B, 0x0053) }, /* Renesas RX610 RX-Stick */
53 { USB_DEVICE(0x0471, 0x066A) }, /* AKTAKOM ACE-1001 cable */
54 { USB_DEVICE(0x0489, 0xE000) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM Mobile */
55 { USB_DEVICE(0x0489, 0xE003) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM Mobile */
56 { USB_DEVICE(0x0745, 0x1000) }, /* CipherLab USB CCD Barcode Scanner 1000 */
57 { USB_DEVICE(0x0846, 0x1100) }, /* NetGear Managed Switch M4100 series, M5300 series, M7100 series */
58 { USB_DEVICE(0x08e6, 0x5501) }, /* Gemalto Prox-PU/CU contactless smartcard reader */
59 { USB_DEVICE(0x08FD, 0x000A) }, /* Digianswer A/S , ZigBee/802.15.4 MAC Device */
60 { USB_DEVICE(0x0908, 0x01FF) }, /* Siemens RUGGEDCOM USB Serial Console */
61 { USB_DEVICE(0x0BED, 0x1100) }, /* MEI (TM) Cashflow-SC Bill/Voucher Acceptor */
62 { USB_DEVICE(0x0BED, 0x1101) }, /* MEI series 2000 Combo Acceptor */
63 { USB_DEVICE(0x0FCF, 0x1003) }, /* Dynastream ANT development board */
64 { USB_DEVICE(0x0FCF, 0x1004) }, /* Dynastream ANT2USB */
65 { USB_DEVICE(0x0FCF, 0x1006) }, /* Dynastream ANT development board */
66 { USB_DEVICE(0x0FDE, 0xCA05) }, /* OWL Wireless Electricity Monitor CM-160 */
67 { USB_DEVICE(0x10A6, 0xAA26) }, /* Knock-off DCU-11 cable */
68 { USB_DEVICE(0x10AB, 0x10C5) }, /* Siemens MC60 Cable */
69 { USB_DEVICE(0x10B5, 0xAC70) }, /* Nokia CA-42 USB */
70 { USB_DEVICE(0x10C4, 0x0F91) }, /* Vstabi */
71 { USB_DEVICE(0x10C4, 0x1101) }, /* Arkham Technology DS101 Bus Monitor */
72 { USB_DEVICE(0x10C4, 0x1601) }, /* Arkham Technology DS101 Adapter */
73 { USB_DEVICE(0x10C4, 0x800A) }, /* SPORTident BSM7-D-USB main station */
74 { USB_DEVICE(0x10C4, 0x803B) }, /* Pololu USB-serial converter */
75 { USB_DEVICE(0x10C4, 0x8044) }, /* Cygnal Debug Adapter */
76 { USB_DEVICE(0x10C4, 0x804E) }, /* Software Bisque Paramount ME build-in converter */
77 { USB_DEVICE(0x10C4, 0x8053) }, /* Enfora EDG1228 */
78 { USB_DEVICE(0x10C4, 0x8054) }, /* Enfora GSM2228 */
79 { USB_DEVICE(0x10C4, 0x8066) }, /* Argussoft In-System Programmer */
80 { USB_DEVICE(0x10C4, 0x806F) }, /* IMS USB to RS422 Converter Cable */
81 { USB_DEVICE(0x10C4, 0x807A) }, /* Crumb128 board */
82 { USB_DEVICE(0x10C4, 0x80C4) }, /* Cygnal Integrated Products, Inc., Optris infrared thermometer */
83 { USB_DEVICE(0x10C4, 0x80CA) }, /* Degree Controls Inc */
84 { USB_DEVICE(0x10C4, 0x80DD) }, /* Tracient RFID */
85 { USB_DEVICE(0x10C4, 0x80F6) }, /* Suunto sports instrument */
86 { USB_DEVICE(0x10C4, 0x8115) }, /* Arygon NFC/Mifare Reader */
87 { USB_DEVICE(0x10C4, 0x813D) }, /* Burnside Telecom Deskmobile */
88 { USB_DEVICE(0x10C4, 0x813F) }, /* Tams Master Easy Control */
89 { USB_DEVICE(0x10C4, 0x814A) }, /* West Mountain Radio RIGblaster P&P */
90 { USB_DEVICE(0x10C4, 0x814B) }, /* West Mountain Radio RIGtalk */
91 { USB_DEVICE(0x2405, 0x0003) }, /* West Mountain Radio RIGblaster Advantage */
92 { USB_DEVICE(0x10C4, 0x8156) }, /* B&G H3000 link cable */
93 { USB_DEVICE(0x10C4, 0x815E) }, /* Helicomm IP-Link 1220-DVM */
94 { USB_DEVICE(0x10C4, 0x815F) }, /* Timewave HamLinkUSB */
95 { USB_DEVICE(0x10C4, 0x818B) }, /* AVIT Research USB to TTL */
96 { USB_DEVICE(0x10C4, 0x819F) }, /* MJS USB Toslink Switcher */
97 { USB_DEVICE(0x10C4, 0x81A6) }, /* ThinkOptics WavIt */
98 { USB_DEVICE(0x10C4, 0x81A9) }, /* Multiplex RC Interface */
99 { USB_DEVICE(0x10C4, 0x81AC) }, /* MSD Dash Hawk */
100 { USB_DEVICE(0x10C4, 0x81AD) }, /* INSYS USB Modem */
101 { USB_DEVICE(0x10C4, 0x81C8) }, /* Lipowsky Industrie Elektronik GmbH, Baby-JTAG */
102 { USB_DEVICE(0x10C4, 0x81D7) }, /* IAI Corp. RCB-CV-USB USB to RS485 Adaptor */
103 { USB_DEVICE(0x10C4, 0x81E2) }, /* Lipowsky Industrie Elektronik GmbH, Baby-LIN */
104 { USB_DEVICE(0x10C4, 0x81E7) }, /* Aerocomm Radio */
105 { USB_DEVICE(0x10C4, 0x81E8) }, /* Zephyr Bioharness */
106 { USB_DEVICE(0x10C4, 0x81F2) }, /* C1007 HF band RFID controller */
107 { USB_DEVICE(0x10C4, 0x8218) }, /* Lipowsky Industrie Elektronik GmbH, HARP-1 */
108 { USB_DEVICE(0x10C4, 0x822B) }, /* Modem EDGE(GSM) Comander 2 */
109 { USB_DEVICE(0x10C4, 0x826B) }, /* Cygnal Integrated Products, Inc., Fasttrax GPS demonstration module */
110 { USB_DEVICE(0x10C4, 0x8281) }, /* Nanotec Plug & Drive */
111 { USB_DEVICE(0x10C4, 0x8293) }, /* Telegesis ETRX2USB */
112 { USB_DEVICE(0x10C4, 0x82F4) }, /* Starizona MicroTouch */
113 { USB_DEVICE(0x10C4, 0x82F9) }, /* Procyon AVS */
114 { USB_DEVICE(0x10C4, 0x8341) }, /* Siemens MC35PU GPRS Modem */
115 { USB_DEVICE(0x10C4, 0x8382) }, /* Cygnal Integrated Products, Inc. */
116 { USB_DEVICE(0x10C4, 0x83A8) }, /* Amber Wireless AMB2560 */
117 { USB_DEVICE(0x10C4, 0x83D8) }, /* DekTec DTA Plus VHF/UHF Booster/Attenuator */
118 { USB_DEVICE(0x10C4, 0x8411) }, /* Kyocera GPS Module */
119 { USB_DEVICE(0x10C4, 0x8418) }, /* IRZ Automation Teleport SG-10 GSM/GPRS Modem */
120 { USB_DEVICE(0x10C4, 0x846E) }, /* BEI USB Sensor Interface (VCP) */
121 { USB_DEVICE(0x10C4, 0x8477) }, /* Balluff RFID */
122 { USB_DEVICE(0x10C4, 0x84B6) }, /* Starizona Hyperion */
123 { USB_DEVICE(0x10C4, 0x85EA) }, /* AC-Services IBUS-IF */
124 { USB_DEVICE(0x10C4, 0x85EB) }, /* AC-Services CIS-IBUS */
125 { USB_DEVICE(0x10C4, 0x85F8) }, /* Virtenio Preon32 */
126 { USB_DEVICE(0x10C4, 0x8664) }, /* AC-Services CAN-IF */
127 { USB_DEVICE(0x10C4, 0x8665) }, /* AC-Services OBD-IF */
128 { USB_DEVICE(0x10C4, 0x8856) }, /* CEL EM357 ZigBee USB Stick - LR */
129 { USB_DEVICE(0x10C4, 0x8857) }, /* CEL EM357 ZigBee USB Stick */
130 { USB_DEVICE(0x10C4, 0x88A4) }, /* MMB Networks ZigBee USB Device */
131 { USB_DEVICE(0x10C4, 0x88A5) }, /* Planet Innovation Ingeni ZigBee USB Device */
132 { USB_DEVICE(0x10C4, 0x8946) }, /* Ketra N1 Wireless Interface */
133 { USB_DEVICE(0x10C4, 0x8977) }, /* CEL MeshWorks DevKit Device */
134 { USB_DEVICE(0x10C4, 0x8998) }, /* KCF Technologies PRN */
135 { USB_DEVICE(0x10C4, 0x8A2A) }, /* HubZ dual ZigBee and Z-Wave dongle */
136 { USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */
137 { USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */
138 { USB_DEVICE(0x10C4, 0xEA70) }, /* Silicon Labs factory default */
139 { USB_DEVICE(0x10C4, 0xEA71) }, /* Infinity GPS-MIC-1 Radio Monophone */
140 { USB_DEVICE(0x10C4, 0xF001) }, /* Elan Digital Systems USBscope50 */
141 { USB_DEVICE(0x10C4, 0xF002) }, /* Elan Digital Systems USBwave12 */
142 { USB_DEVICE(0x10C4, 0xF003) }, /* Elan Digital Systems USBpulse100 */
143 { USB_DEVICE(0x10C4, 0xF004) }, /* Elan Digital Systems USBcount50 */
144 { USB_DEVICE(0x10C5, 0xEA61) }, /* Silicon Labs MobiData GPRS USB Modem */
145 { USB_DEVICE(0x10CE, 0xEA6A) }, /* Silicon Labs MobiData GPRS USB Modem 100EU */
146 { USB_DEVICE(0x12B8, 0xEC60) }, /* Link G4 ECU */
147 { USB_DEVICE(0x12B8, 0xEC62) }, /* Link G4+ ECU */
148 { USB_DEVICE(0x13AD, 0x9999) }, /* Baltech card reader */
149 { USB_DEVICE(0x1555, 0x0004) }, /* Owen AC4 USB-RS485 Converter */
150 { USB_DEVICE(0x166A, 0x0201) }, /* Clipsal 5500PACA C-Bus Pascal Automation Controller */
151 { USB_DEVICE(0x166A, 0x0301) }, /* Clipsal 5800PC C-Bus Wireless PC Interface */
152 { USB_DEVICE(0x166A, 0x0303) }, /* Clipsal 5500PCU C-Bus USB interface */
153 { USB_DEVICE(0x166A, 0x0304) }, /* Clipsal 5000CT2 C-Bus Black and White Touchscreen */
154 { USB_DEVICE(0x166A, 0x0305) }, /* Clipsal C-5000CT2 C-Bus Spectrum Colour Touchscreen */
155 { USB_DEVICE(0x166A, 0x0401) }, /* Clipsal L51xx C-Bus Architectural Dimmer */
156 { USB_DEVICE(0x166A, 0x0101) }, /* Clipsal 5560884 C-Bus Multi-room Audio Matrix Switcher */
157 { USB_DEVICE(0x16C0, 0x09B0) }, /* Lunatico Seletek */
158 { USB_DEVICE(0x16C0, 0x09B1) }, /* Lunatico Seletek */
159 { USB_DEVICE(0x16D6, 0x0001) }, /* Jablotron serial interface */
160 { USB_DEVICE(0x16DC, 0x0010) }, /* W-IE-NE-R Plein & Baus GmbH PL512 Power Supply */
161 { USB_DEVICE(0x16DC, 0x0011) }, /* W-IE-NE-R Plein & Baus GmbH RCM Remote Control for MARATON Power Supply */
162 { USB_DEVICE(0x16DC, 0x0012) }, /* W-IE-NE-R Plein & Baus GmbH MPOD Multi Channel Power Supply */
163 { USB_DEVICE(0x16DC, 0x0015) }, /* W-IE-NE-R Plein & Baus GmbH CML Control, Monitoring and Data Logger */
164 { USB_DEVICE(0x17A8, 0x0001) }, /* Kamstrup Optical Eye/3-wire */
165 { USB_DEVICE(0x17A8, 0x0005) }, /* Kamstrup M-Bus Master MultiPort 250D */
166 { USB_DEVICE(0x17F4, 0xAAAA) }, /* Wavesense Jazz blood glucose meter */
167 { USB_DEVICE(0x1843, 0x0200) }, /* Vaisala USB Instrument Cable */
168 { USB_DEVICE(0x18EF, 0xE00F) }, /* ELV USB-I2C-Interface */
169 { USB_DEVICE(0x18EF, 0xE025) }, /* ELV Marble Sound Board 1 */
170 { USB_DEVICE(0x1901, 0x0190) }, /* GE B850 CP2105 Recorder interface */
171 { USB_DEVICE(0x1901, 0x0193) }, /* GE B650 CP2104 PMC interface */
172 { USB_DEVICE(0x1901, 0x0194) }, /* GE Healthcare Remote Alarm Box */
173 { USB_DEVICE(0x19CF, 0x3000) }, /* Parrot NMEA GPS Flight Recorder */
174 { USB_DEVICE(0x1ADB, 0x0001) }, /* Schweitzer Engineering C662 Cable */
175 { USB_DEVICE(0x1B1C, 0x1C00) }, /* Corsair USB Dongle */
176 { USB_DEVICE(0x1BA4, 0x0002) }, /* Silicon Labs 358x factory default */
177 { USB_DEVICE(0x1BE3, 0x07A6) }, /* WAGO 750-923 USB Service Cable */
178 { USB_DEVICE(0x1D6F, 0x0010) }, /* Seluxit ApS RF Dongle */
179 { USB_DEVICE(0x1E29, 0x0102) }, /* Festo CPX-USB */
180 { USB_DEVICE(0x1E29, 0x0501) }, /* Festo CMSP */
181 { USB_DEVICE(0x1FB9, 0x0100) }, /* Lake Shore Model 121 Current Source */
182 { USB_DEVICE(0x1FB9, 0x0200) }, /* Lake Shore Model 218A Temperature Monitor */
183 { USB_DEVICE(0x1FB9, 0x0201) }, /* Lake Shore Model 219 Temperature Monitor */
184 { USB_DEVICE(0x1FB9, 0x0202) }, /* Lake Shore Model 233 Temperature Transmitter */
185 { USB_DEVICE(0x1FB9, 0x0203) }, /* Lake Shore Model 235 Temperature Transmitter */
186 { USB_DEVICE(0x1FB9, 0x0300) }, /* Lake Shore Model 335 Temperature Controller */
187 { USB_DEVICE(0x1FB9, 0x0301) }, /* Lake Shore Model 336 Temperature Controller */
188 { USB_DEVICE(0x1FB9, 0x0302) }, /* Lake Shore Model 350 Temperature Controller */
189 { USB_DEVICE(0x1FB9, 0x0303) }, /* Lake Shore Model 371 AC Bridge */
190 { USB_DEVICE(0x1FB9, 0x0400) }, /* Lake Shore Model 411 Handheld Gaussmeter */
191 { USB_DEVICE(0x1FB9, 0x0401) }, /* Lake Shore Model 425 Gaussmeter */
192 { USB_DEVICE(0x1FB9, 0x0402) }, /* Lake Shore Model 455A Gaussmeter */
193 { USB_DEVICE(0x1FB9, 0x0403) }, /* Lake Shore Model 475A Gaussmeter */
194 { USB_DEVICE(0x1FB9, 0x0404) }, /* Lake Shore Model 465 Three Axis Gaussmeter */
195 { USB_DEVICE(0x1FB9, 0x0600) }, /* Lake Shore Model 625A Superconducting MPS */
196 { USB_DEVICE(0x1FB9, 0x0601) }, /* Lake Shore Model 642A Magnet Power Supply */
197 { USB_DEVICE(0x1FB9, 0x0602) }, /* Lake Shore Model 648 Magnet Power Supply */
198 { USB_DEVICE(0x1FB9, 0x0700) }, /* Lake Shore Model 737 VSM Controller */
199 { USB_DEVICE(0x1FB9, 0x0701) }, /* Lake Shore Model 776 Hall Matrix */
200 { USB_DEVICE(0x2626, 0xEA60) }, /* Aruba Networks 7xxx USB Serial Console */
201 { USB_DEVICE(0x3195, 0xF190) }, /* Link Instruments MSO-19 */
202 { USB_DEVICE(0x3195, 0xF280) }, /* Link Instruments MSO-28 */
203 { USB_DEVICE(0x3195, 0xF281) }, /* Link Instruments MSO-28 */
204 { USB_DEVICE(0x413C, 0x9500) }, /* DW700 GPS USB interface */
205 { } /* Terminating Entry */
206};
207
208MODULE_DEVICE_TABLE(usb, id_table);
209
210struct cp210x_port_private {
211 __u8 bInterfaceNumber;
212 bool has_swapped_line_ctl;
213};
214
215static struct usb_serial_driver cp210x_device = {
216 .driver = {
217 .owner = THIS_MODULE,
218 .name = "cp210x",
219 },
220 .id_table = id_table,
221 .num_ports = 1,
222 .bulk_in_size = 256,
223 .bulk_out_size = 256,
224 .open = cp210x_open,
225 .close = cp210x_close,
226 .break_ctl = cp210x_break_ctl,
227 .set_termios = cp210x_set_termios,
228 .tx_empty = cp210x_tx_empty,
229 .tiocmget = cp210x_tiocmget,
230 .tiocmset = cp210x_tiocmset,
231 .port_probe = cp210x_port_probe,
232 .port_remove = cp210x_port_remove,
233 .dtr_rts = cp210x_dtr_rts
234};
235
236static struct usb_serial_driver * const serial_drivers[] = {
237 &cp210x_device, NULL
238};
239
240/* Config request types */
241#define REQTYPE_HOST_TO_INTERFACE 0x41
242#define REQTYPE_INTERFACE_TO_HOST 0xc1
243#define REQTYPE_HOST_TO_DEVICE 0x40
244#define REQTYPE_DEVICE_TO_HOST 0xc0
245
246/* Config request codes */
247#define CP210X_IFC_ENABLE 0x00
248#define CP210X_SET_BAUDDIV 0x01
249#define CP210X_GET_BAUDDIV 0x02
250#define CP210X_SET_LINE_CTL 0x03
251#define CP210X_GET_LINE_CTL 0x04
252#define CP210X_SET_BREAK 0x05
253#define CP210X_IMM_CHAR 0x06
254#define CP210X_SET_MHS 0x07
255#define CP210X_GET_MDMSTS 0x08
256#define CP210X_SET_XON 0x09
257#define CP210X_SET_XOFF 0x0A
258#define CP210X_SET_EVENTMASK 0x0B
259#define CP210X_GET_EVENTMASK 0x0C
260#define CP210X_SET_CHAR 0x0D
261#define CP210X_GET_CHARS 0x0E
262#define CP210X_GET_PROPS 0x0F
263#define CP210X_GET_COMM_STATUS 0x10
264#define CP210X_RESET 0x11
265#define CP210X_PURGE 0x12
266#define CP210X_SET_FLOW 0x13
267#define CP210X_GET_FLOW 0x14
268#define CP210X_EMBED_EVENTS 0x15
269#define CP210X_GET_EVENTSTATE 0x16
270#define CP210X_SET_CHARS 0x19
271#define CP210X_GET_BAUDRATE 0x1D
272#define CP210X_SET_BAUDRATE 0x1E
273
274/* CP210X_IFC_ENABLE */
275#define UART_ENABLE 0x0001
276#define UART_DISABLE 0x0000
277
278/* CP210X_(SET|GET)_BAUDDIV */
279#define BAUD_RATE_GEN_FREQ 0x384000
280
281/* CP210X_(SET|GET)_LINE_CTL */
282#define BITS_DATA_MASK 0X0f00
283#define BITS_DATA_5 0X0500
284#define BITS_DATA_6 0X0600
285#define BITS_DATA_7 0X0700
286#define BITS_DATA_8 0X0800
287#define BITS_DATA_9 0X0900
288
289#define BITS_PARITY_MASK 0x00f0
290#define BITS_PARITY_NONE 0x0000
291#define BITS_PARITY_ODD 0x0010
292#define BITS_PARITY_EVEN 0x0020
293#define BITS_PARITY_MARK 0x0030
294#define BITS_PARITY_SPACE 0x0040
295
296#define BITS_STOP_MASK 0x000f
297#define BITS_STOP_1 0x0000
298#define BITS_STOP_1_5 0x0001
299#define BITS_STOP_2 0x0002
300
301/* CP210X_SET_BREAK */
302#define BREAK_ON 0x0001
303#define BREAK_OFF 0x0000
304
305/* CP210X_(SET_MHS|GET_MDMSTS) */
306#define CONTROL_DTR 0x0001
307#define CONTROL_RTS 0x0002
308#define CONTROL_CTS 0x0010
309#define CONTROL_DSR 0x0020
310#define CONTROL_RING 0x0040
311#define CONTROL_DCD 0x0080
312#define CONTROL_WRITE_DTR 0x0100
313#define CONTROL_WRITE_RTS 0x0200
314
315/* CP210X_GET_COMM_STATUS returns these 0x13 bytes */
316struct cp210x_comm_status {
317 __le32 ulErrors;
318 __le32 ulHoldReasons;
319 __le32 ulAmountInInQueue;
320 __le32 ulAmountInOutQueue;
321 u8 bEofReceived;
322 u8 bWaitForImmediate;
323 u8 bReserved;
324} __packed;
325
326/*
327 * CP210X_PURGE - 16 bits passed in wValue of USB request.
328 * SiLabs app note AN571 gives a strange description of the 4 bits:
329 * bit 0 or bit 2 clears the transmit queue and 1 or 3 receive.
330 * writing 1 to all, however, purges cp2108 well enough to avoid the hang.
331 */
332#define PURGE_ALL 0x000f
333
334/*
335 * Reads a variable-sized block of CP210X_ registers, identified by req.
336 * Returns data into buf in native USB byte order.
337 */
338static int cp210x_read_reg_block(struct usb_serial_port *port, u8 req,
339 void *buf, int bufsize)
340{
341 struct usb_serial *serial = port->serial;
342 struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
343 void *dmabuf;
344 int result;
345
346 dmabuf = kmalloc(bufsize, GFP_KERNEL);
347 if (!dmabuf) {
348 /*
349 * FIXME Some callers don't bother to check for error,
350 * at least give them consistent junk until they are fixed
351 */
352 memset(buf, 0, bufsize);
353 return -ENOMEM;
354 }
355
356 result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
357 req, REQTYPE_INTERFACE_TO_HOST, 0,
358 port_priv->bInterfaceNumber, dmabuf, bufsize,
359 USB_CTRL_SET_TIMEOUT);
360 if (result == bufsize) {
361 memcpy(buf, dmabuf, bufsize);
362 result = 0;
363 } else {
364 dev_err(&port->dev, "failed get req 0x%x size %d status: %d\n",
365 req, bufsize, result);
366 if (result >= 0)
367 result = -EPROTO;
368
369 /*
370 * FIXME Some callers don't bother to check for error,
371 * at least give them consistent junk until they are fixed
372 */
373 memset(buf, 0, bufsize);
374 }
375
376 kfree(dmabuf);
377
378 return result;
379}
380
381/*
382 * Reads any 32-bit CP210X_ register identified by req.
383 */
384static int cp210x_read_u32_reg(struct usb_serial_port *port, u8 req, u32 *val)
385{
386 __le32 le32_val;
387 int err;
388
389 err = cp210x_read_reg_block(port, req, &le32_val, sizeof(le32_val));
390 if (err) {
391 /*
392 * FIXME Some callers don't bother to check for error,
393 * at least give them consistent junk until they are fixed
394 */
395 *val = 0;
396 return err;
397 }
398
399 *val = le32_to_cpu(le32_val);
400
401 return 0;
402}
403
404/*
405 * Reads any 16-bit CP210X_ register identified by req.
406 */
407static int cp210x_read_u16_reg(struct usb_serial_port *port, u8 req, u16 *val)
408{
409 __le16 le16_val;
410 int err;
411
412 err = cp210x_read_reg_block(port, req, &le16_val, sizeof(le16_val));
413 if (err)
414 return err;
415
416 *val = le16_to_cpu(le16_val);
417
418 return 0;
419}
420
421/*
422 * Reads any 8-bit CP210X_ register identified by req.
423 */
424static int cp210x_read_u8_reg(struct usb_serial_port *port, u8 req, u8 *val)
425{
426 return cp210x_read_reg_block(port, req, val, sizeof(*val));
427}
428
429/*
430 * Writes any 16-bit CP210X_ register (req) whose value is passed
431 * entirely in the wValue field of the USB request.
432 */
433static int cp210x_write_u16_reg(struct usb_serial_port *port, u8 req, u16 val)
434{
435 struct usb_serial *serial = port->serial;
436 struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
437 int result;
438
439 result = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
440 req, REQTYPE_HOST_TO_INTERFACE, val,
441 port_priv->bInterfaceNumber, NULL, 0,
442 USB_CTRL_SET_TIMEOUT);
443 if (result < 0) {
444 dev_err(&port->dev, "failed set request 0x%x status: %d\n",
445 req, result);
446 }
447
448 return result;
449}
450
451/*
452 * Writes a variable-sized block of CP210X_ registers, identified by req.
453 * Data in buf must be in native USB byte order.
454 */
455static int cp210x_write_reg_block(struct usb_serial_port *port, u8 req,
456 void *buf, int bufsize)
457{
458 struct usb_serial *serial = port->serial;
459 struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
460 void *dmabuf;
461 int result;
462
463 dmabuf = kmalloc(bufsize, GFP_KERNEL);
464 if (!dmabuf)
465 return -ENOMEM;
466
467 memcpy(dmabuf, buf, bufsize);
468
469 result = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
470 req, REQTYPE_HOST_TO_INTERFACE, 0,
471 port_priv->bInterfaceNumber, dmabuf, bufsize,
472 USB_CTRL_SET_TIMEOUT);
473
474 kfree(dmabuf);
475
476 if (result == bufsize) {
477 result = 0;
478 } else {
479 dev_err(&port->dev, "failed set req 0x%x size %d status: %d\n",
480 req, bufsize, result);
481 if (result >= 0)
482 result = -EPROTO;
483 }
484
485 return result;
486}
487
488/*
489 * Writes any 32-bit CP210X_ register identified by req.
490 */
491static int cp210x_write_u32_reg(struct usb_serial_port *port, u8 req, u32 val)
492{
493 __le32 le32_val;
494
495 le32_val = cpu_to_le32(val);
496
497 return cp210x_write_reg_block(port, req, &le32_val, sizeof(le32_val));
498}
499
500/*
501 * Detect CP2108 GET_LINE_CTL bug and activate workaround.
502 * Write a known good value 0x800, read it back.
503 * If it comes back swapped the bug is detected.
504 * Preserve the original register value.
505 */
506static int cp210x_detect_swapped_line_ctl(struct usb_serial_port *port)
507{
508 struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
509 u16 line_ctl_save;
510 u16 line_ctl_test;
511 int err;
512
513 err = cp210x_read_u16_reg(port, CP210X_GET_LINE_CTL, &line_ctl_save);
514 if (err)
515 return err;
516
517 err = cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, 0x800);
518 if (err)
519 return err;
520
521 err = cp210x_read_u16_reg(port, CP210X_GET_LINE_CTL, &line_ctl_test);
522 if (err)
523 return err;
524
525 if (line_ctl_test == 8) {
526 port_priv->has_swapped_line_ctl = true;
527 line_ctl_save = swab16(line_ctl_save);
528 }
529
530 return cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, line_ctl_save);
531}
532
533/*
534 * Must always be called instead of cp210x_read_u16_reg(CP210X_GET_LINE_CTL)
535 * to workaround cp2108 bug and get correct value.
536 */
537static int cp210x_get_line_ctl(struct usb_serial_port *port, u16 *ctl)
538{
539 struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
540 int err;
541
542 err = cp210x_read_u16_reg(port, CP210X_GET_LINE_CTL, ctl);
543 if (err)
544 return err;
545
546 /* Workaround swapped bytes in 16-bit value from CP210X_GET_LINE_CTL */
547 if (port_priv->has_swapped_line_ctl)
548 *ctl = swab16(*ctl);
549
550 return 0;
551}
552
553/*
554 * cp210x_quantise_baudrate
555 * Quantises the baud rate as per AN205 Table 1
556 */
557static unsigned int cp210x_quantise_baudrate(unsigned int baud)
558{
559 if (baud <= 300)
560 baud = 300;
561 else if (baud <= 600) baud = 600;
562 else if (baud <= 1200) baud = 1200;
563 else if (baud <= 1800) baud = 1800;
564 else if (baud <= 2400) baud = 2400;
565 else if (baud <= 4000) baud = 4000;
566 else if (baud <= 4803) baud = 4800;
567 else if (baud <= 7207) baud = 7200;
568 else if (baud <= 9612) baud = 9600;
569 else if (baud <= 14428) baud = 14400;
570 else if (baud <= 16062) baud = 16000;
571 else if (baud <= 19250) baud = 19200;
572 else if (baud <= 28912) baud = 28800;
573 else if (baud <= 38601) baud = 38400;
574 else if (baud <= 51558) baud = 51200;
575 else if (baud <= 56280) baud = 56000;
576 else if (baud <= 58053) baud = 57600;
577 else if (baud <= 64111) baud = 64000;
578 else if (baud <= 77608) baud = 76800;
579 else if (baud <= 117028) baud = 115200;
580 else if (baud <= 129347) baud = 128000;
581 else if (baud <= 156868) baud = 153600;
582 else if (baud <= 237832) baud = 230400;
583 else if (baud <= 254234) baud = 250000;
584 else if (baud <= 273066) baud = 256000;
585 else if (baud <= 491520) baud = 460800;
586 else if (baud <= 567138) baud = 500000;
587 else if (baud <= 670254) baud = 576000;
588 else if (baud < 1000000)
589 baud = 921600;
590 else if (baud > 2000000)
591 baud = 2000000;
592 return baud;
593}
594
595static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *port)
596{
597 int result;
598
599 result = cp210x_write_u16_reg(port, CP210X_IFC_ENABLE, UART_ENABLE);
600 if (result) {
601 dev_err(&port->dev, "%s - Unable to enable UART\n", __func__);
602 return result;
603 }
604
605 /* Configure the termios structure */
606 cp210x_get_termios(tty, port);
607
608 /* The baud rate must be initialised on cp2104 */
609 if (tty)
610 cp210x_change_speed(tty, port, NULL);
611
612 return usb_serial_generic_open(tty, port);
613}
614
615static void cp210x_close(struct usb_serial_port *port)
616{
617 usb_serial_generic_close(port);
618
619 /* Clear both queues; cp2108 needs this to avoid an occasional hang */
620 cp210x_write_u16_reg(port, CP210X_PURGE, PURGE_ALL);
621
622 cp210x_write_u16_reg(port, CP210X_IFC_ENABLE, UART_DISABLE);
623}
624
625/*
626 * Read how many bytes are waiting in the TX queue.
627 */
628static int cp210x_get_tx_queue_byte_count(struct usb_serial_port *port,
629 u32 *count)
630{
631 struct usb_serial *serial = port->serial;
632 struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
633 struct cp210x_comm_status *sts;
634 int result;
635
636 sts = kmalloc(sizeof(*sts), GFP_KERNEL);
637 if (!sts)
638 return -ENOMEM;
639
640 result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
641 CP210X_GET_COMM_STATUS, REQTYPE_INTERFACE_TO_HOST,
642 0, port_priv->bInterfaceNumber, sts, sizeof(*sts),
643 USB_CTRL_GET_TIMEOUT);
644 if (result == sizeof(*sts)) {
645 *count = le32_to_cpu(sts->ulAmountInOutQueue);
646 result = 0;
647 } else {
648 dev_err(&port->dev, "failed to get comm status: %d\n", result);
649 if (result >= 0)
650 result = -EPROTO;
651 }
652
653 kfree(sts);
654
655 return result;
656}
657
658static bool cp210x_tx_empty(struct usb_serial_port *port)
659{
660 int err;
661 u32 count;
662
663 err = cp210x_get_tx_queue_byte_count(port, &count);
664 if (err)
665 return true;
666
667 return !count;
668}
669
670/*
671 * cp210x_get_termios
672 * Reads the baud rate, data bits, parity, stop bits and flow control mode
673 * from the device, corrects any unsupported values, and configures the
674 * termios structure to reflect the state of the device
675 */
676static void cp210x_get_termios(struct tty_struct *tty,
677 struct usb_serial_port *port)
678{
679 unsigned int baud;
680
681 if (tty) {
682 cp210x_get_termios_port(tty->driver_data,
683 &tty->termios.c_cflag, &baud);
684 tty_encode_baud_rate(tty, baud, baud);
685 } else {
686 unsigned int cflag;
687 cflag = 0;
688 cp210x_get_termios_port(port, &cflag, &baud);
689 }
690}
691
692/*
693 * cp210x_get_termios_port
694 * This is the heart of cp210x_get_termios which always uses a &usb_serial_port.
695 */
696static void cp210x_get_termios_port(struct usb_serial_port *port,
697 unsigned int *cflagp, unsigned int *baudp)
698{
699 struct device *dev = &port->dev;
700 unsigned int cflag;
701 u8 modem_ctl[16];
702 u32 baud;
703 u16 bits;
704
705 cp210x_read_u32_reg(port, CP210X_GET_BAUDRATE, &baud);
706
707 dev_dbg(dev, "%s - baud rate = %d\n", __func__, baud);
708 *baudp = baud;
709
710 cflag = *cflagp;
711
712 cp210x_get_line_ctl(port, &bits);
713 cflag &= ~CSIZE;
714 switch (bits & BITS_DATA_MASK) {
715 case BITS_DATA_5:
716 dev_dbg(dev, "%s - data bits = 5\n", __func__);
717 cflag |= CS5;
718 break;
719 case BITS_DATA_6:
720 dev_dbg(dev, "%s - data bits = 6\n", __func__);
721 cflag |= CS6;
722 break;
723 case BITS_DATA_7:
724 dev_dbg(dev, "%s - data bits = 7\n", __func__);
725 cflag |= CS7;
726 break;
727 case BITS_DATA_8:
728 dev_dbg(dev, "%s - data bits = 8\n", __func__);
729 cflag |= CS8;
730 break;
731 case BITS_DATA_9:
732 dev_dbg(dev, "%s - data bits = 9 (not supported, using 8 data bits)\n", __func__);
733 cflag |= CS8;
734 bits &= ~BITS_DATA_MASK;
735 bits |= BITS_DATA_8;
736 cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits);
737 break;
738 default:
739 dev_dbg(dev, "%s - Unknown number of data bits, using 8\n", __func__);
740 cflag |= CS8;
741 bits &= ~BITS_DATA_MASK;
742 bits |= BITS_DATA_8;
743 cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits);
744 break;
745 }
746
747 switch (bits & BITS_PARITY_MASK) {
748 case BITS_PARITY_NONE:
749 dev_dbg(dev, "%s - parity = NONE\n", __func__);
750 cflag &= ~PARENB;
751 break;
752 case BITS_PARITY_ODD:
753 dev_dbg(dev, "%s - parity = ODD\n", __func__);
754 cflag |= (PARENB|PARODD);
755 break;
756 case BITS_PARITY_EVEN:
757 dev_dbg(dev, "%s - parity = EVEN\n", __func__);
758 cflag &= ~PARODD;
759 cflag |= PARENB;
760 break;
761 case BITS_PARITY_MARK:
762 dev_dbg(dev, "%s - parity = MARK\n", __func__);
763 cflag |= (PARENB|PARODD|CMSPAR);
764 break;
765 case BITS_PARITY_SPACE:
766 dev_dbg(dev, "%s - parity = SPACE\n", __func__);
767 cflag &= ~PARODD;
768 cflag |= (PARENB|CMSPAR);
769 break;
770 default:
771 dev_dbg(dev, "%s - Unknown parity mode, disabling parity\n", __func__);
772 cflag &= ~PARENB;
773 bits &= ~BITS_PARITY_MASK;
774 cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits);
775 break;
776 }
777
778 cflag &= ~CSTOPB;
779 switch (bits & BITS_STOP_MASK) {
780 case BITS_STOP_1:
781 dev_dbg(dev, "%s - stop bits = 1\n", __func__);
782 break;
783 case BITS_STOP_1_5:
784 dev_dbg(dev, "%s - stop bits = 1.5 (not supported, using 1 stop bit)\n", __func__);
785 bits &= ~BITS_STOP_MASK;
786 cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits);
787 break;
788 case BITS_STOP_2:
789 dev_dbg(dev, "%s - stop bits = 2\n", __func__);
790 cflag |= CSTOPB;
791 break;
792 default:
793 dev_dbg(dev, "%s - Unknown number of stop bits, using 1 stop bit\n", __func__);
794 bits &= ~BITS_STOP_MASK;
795 cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits);
796 break;
797 }
798
799 cp210x_read_reg_block(port, CP210X_GET_FLOW, modem_ctl,
800 sizeof(modem_ctl));
801 if (modem_ctl[0] & 0x08) {
802 dev_dbg(dev, "%s - flow control = CRTSCTS\n", __func__);
803 cflag |= CRTSCTS;
804 } else {
805 dev_dbg(dev, "%s - flow control = NONE\n", __func__);
806 cflag &= ~CRTSCTS;
807 }
808
809 *cflagp = cflag;
810}
811
812/*
813 * CP2101 supports the following baud rates:
814 *
815 * 300, 600, 1200, 1800, 2400, 4800, 7200, 9600, 14400, 19200, 28800,
816 * 38400, 56000, 57600, 115200, 128000, 230400, 460800, 921600
817 *
818 * CP2102 and CP2103 support the following additional rates:
819 *
820 * 4000, 16000, 51200, 64000, 76800, 153600, 250000, 256000, 500000,
821 * 576000
822 *
823 * The device will map a requested rate to a supported one, but the result
824 * of requests for rates greater than 1053257 is undefined (see AN205).
825 *
826 * CP2104, CP2105 and CP2110 support most rates up to 2M, 921k and 1M baud,
827 * respectively, with an error less than 1%. The actual rates are determined
828 * by
829 *
830 * div = round(freq / (2 x prescale x request))
831 * actual = freq / (2 x prescale x div)
832 *
833 * For CP2104 and CP2105 freq is 48Mhz and prescale is 4 for request <= 365bps
834 * or 1 otherwise.
835 * For CP2110 freq is 24Mhz and prescale is 4 for request <= 300bps or 1
836 * otherwise.
837 */
838static void cp210x_change_speed(struct tty_struct *tty,
839 struct usb_serial_port *port, struct ktermios *old_termios)
840{
841 u32 baud;
842
843 baud = tty->termios.c_ospeed;
844
845 /* This maps the requested rate to a rate valid on cp2102 or cp2103,
846 * or to an arbitrary rate in [1M,2M].
847 *
848 * NOTE: B0 is not implemented.
849 */
850 baud = cp210x_quantise_baudrate(baud);
851
852 dev_dbg(&port->dev, "%s - setting baud rate to %u\n", __func__, baud);
853 if (cp210x_write_u32_reg(port, CP210X_SET_BAUDRATE, baud)) {
854 dev_warn(&port->dev, "failed to set baud rate to %u\n", baud);
855 if (old_termios)
856 baud = old_termios->c_ospeed;
857 else
858 baud = 9600;
859 }
860
861 tty_encode_baud_rate(tty, baud, baud);
862}
863
864static void cp210x_set_termios(struct tty_struct *tty,
865 struct usb_serial_port *port, struct ktermios *old_termios)
866{
867 struct device *dev = &port->dev;
868 unsigned int cflag, old_cflag;
869 u16 bits;
870 u8 modem_ctl[16];
871
872 cflag = tty->termios.c_cflag;
873 old_cflag = old_termios->c_cflag;
874
875 if (tty->termios.c_ospeed != old_termios->c_ospeed)
876 cp210x_change_speed(tty, port, old_termios);
877
878 /* If the number of data bits is to be updated */
879 if ((cflag & CSIZE) != (old_cflag & CSIZE)) {
880 cp210x_get_line_ctl(port, &bits);
881 bits &= ~BITS_DATA_MASK;
882 switch (cflag & CSIZE) {
883 case CS5:
884 bits |= BITS_DATA_5;
885 dev_dbg(dev, "%s - data bits = 5\n", __func__);
886 break;
887 case CS6:
888 bits |= BITS_DATA_6;
889 dev_dbg(dev, "%s - data bits = 6\n", __func__);
890 break;
891 case CS7:
892 bits |= BITS_DATA_7;
893 dev_dbg(dev, "%s - data bits = 7\n", __func__);
894 break;
895 case CS8:
896 bits |= BITS_DATA_8;
897 dev_dbg(dev, "%s - data bits = 8\n", __func__);
898 break;
899 /*case CS9:
900 bits |= BITS_DATA_9;
901 dev_dbg(dev, "%s - data bits = 9\n", __func__);
902 break;*/
903 default:
904 dev_dbg(dev, "cp210x driver does not support the number of bits requested, using 8 bit mode\n");
905 bits |= BITS_DATA_8;
906 break;
907 }
908 if (cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits))
909 dev_dbg(dev, "Number of data bits requested not supported by device\n");
910 }
911
912 if ((cflag & (PARENB|PARODD|CMSPAR)) !=
913 (old_cflag & (PARENB|PARODD|CMSPAR))) {
914 cp210x_get_line_ctl(port, &bits);
915 bits &= ~BITS_PARITY_MASK;
916 if (cflag & PARENB) {
917 if (cflag & CMSPAR) {
918 if (cflag & PARODD) {
919 bits |= BITS_PARITY_MARK;
920 dev_dbg(dev, "%s - parity = MARK\n", __func__);
921 } else {
922 bits |= BITS_PARITY_SPACE;
923 dev_dbg(dev, "%s - parity = SPACE\n", __func__);
924 }
925 } else {
926 if (cflag & PARODD) {
927 bits |= BITS_PARITY_ODD;
928 dev_dbg(dev, "%s - parity = ODD\n", __func__);
929 } else {
930 bits |= BITS_PARITY_EVEN;
931 dev_dbg(dev, "%s - parity = EVEN\n", __func__);
932 }
933 }
934 }
935 if (cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits))
936 dev_dbg(dev, "Parity mode not supported by device\n");
937 }
938
939 if ((cflag & CSTOPB) != (old_cflag & CSTOPB)) {
940 cp210x_get_line_ctl(port, &bits);
941 bits &= ~BITS_STOP_MASK;
942 if (cflag & CSTOPB) {
943 bits |= BITS_STOP_2;
944 dev_dbg(dev, "%s - stop bits = 2\n", __func__);
945 } else {
946 bits |= BITS_STOP_1;
947 dev_dbg(dev, "%s - stop bits = 1\n", __func__);
948 }
949 if (cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits))
950 dev_dbg(dev, "Number of stop bits requested not supported by device\n");
951 }
952
953 if ((cflag & CRTSCTS) != (old_cflag & CRTSCTS)) {
954
955 /* Only bytes 0, 4 and 7 out of first 8 have functional bits */
956
957 cp210x_read_reg_block(port, CP210X_GET_FLOW, modem_ctl,
958 sizeof(modem_ctl));
959 dev_dbg(dev, "%s - read modem controls = %02x .. .. .. %02x .. .. %02x\n",
960 __func__, modem_ctl[0], modem_ctl[4], modem_ctl[7]);
961
962 if (cflag & CRTSCTS) {
963 modem_ctl[0] &= ~0x7B;
964 modem_ctl[0] |= 0x09;
965 modem_ctl[4] = 0x80;
966 /* FIXME - why clear reserved bits just read? */
967 modem_ctl[5] = 0;
968 modem_ctl[6] = 0;
969 modem_ctl[7] = 0;
970 dev_dbg(dev, "%s - flow control = CRTSCTS\n", __func__);
971 } else {
972 modem_ctl[0] &= ~0x7B;
973 modem_ctl[0] |= 0x01;
974 /* FIXME - OR here instead of assignment looks wrong */
975 modem_ctl[4] |= 0x40;
976 dev_dbg(dev, "%s - flow control = NONE\n", __func__);
977 }
978
979 dev_dbg(dev, "%s - write modem controls = %02x .. .. .. %02x .. .. %02x\n",
980 __func__, modem_ctl[0], modem_ctl[4], modem_ctl[7]);
981 cp210x_write_reg_block(port, CP210X_SET_FLOW, modem_ctl,
982 sizeof(modem_ctl));
983 }
984
985}
986
987static int cp210x_tiocmset(struct tty_struct *tty,
988 unsigned int set, unsigned int clear)
989{
990 struct usb_serial_port *port = tty->driver_data;
991 return cp210x_tiocmset_port(port, set, clear);
992}
993
994static int cp210x_tiocmset_port(struct usb_serial_port *port,
995 unsigned int set, unsigned int clear)
996{
997 u16 control = 0;
998
999 if (set & TIOCM_RTS) {
1000 control |= CONTROL_RTS;
1001 control |= CONTROL_WRITE_RTS;
1002 }
1003 if (set & TIOCM_DTR) {
1004 control |= CONTROL_DTR;
1005 control |= CONTROL_WRITE_DTR;
1006 }
1007 if (clear & TIOCM_RTS) {
1008 control &= ~CONTROL_RTS;
1009 control |= CONTROL_WRITE_RTS;
1010 }
1011 if (clear & TIOCM_DTR) {
1012 control &= ~CONTROL_DTR;
1013 control |= CONTROL_WRITE_DTR;
1014 }
1015
1016 dev_dbg(&port->dev, "%s - control = 0x%.4x\n", __func__, control);
1017
1018 return cp210x_write_u16_reg(port, CP210X_SET_MHS, control);
1019}
1020
1021static void cp210x_dtr_rts(struct usb_serial_port *p, int on)
1022{
1023 if (on)
1024 cp210x_tiocmset_port(p, TIOCM_DTR|TIOCM_RTS, 0);
1025 else
1026 cp210x_tiocmset_port(p, 0, TIOCM_DTR|TIOCM_RTS);
1027}
1028
1029static int cp210x_tiocmget(struct tty_struct *tty)
1030{
1031 struct usb_serial_port *port = tty->driver_data;
1032 u8 control;
1033 int result;
1034
1035 cp210x_read_u8_reg(port, CP210X_GET_MDMSTS, &control);
1036
1037 result = ((control & CONTROL_DTR) ? TIOCM_DTR : 0)
1038 |((control & CONTROL_RTS) ? TIOCM_RTS : 0)
1039 |((control & CONTROL_CTS) ? TIOCM_CTS : 0)
1040 |((control & CONTROL_DSR) ? TIOCM_DSR : 0)
1041 |((control & CONTROL_RING)? TIOCM_RI : 0)
1042 |((control & CONTROL_DCD) ? TIOCM_CD : 0);
1043
1044 dev_dbg(&port->dev, "%s - control = 0x%.2x\n", __func__, control);
1045
1046 return result;
1047}
1048
1049static void cp210x_break_ctl(struct tty_struct *tty, int break_state)
1050{
1051 struct usb_serial_port *port = tty->driver_data;
1052 u16 state;
1053
1054 if (break_state == 0)
1055 state = BREAK_OFF;
1056 else
1057 state = BREAK_ON;
1058 dev_dbg(&port->dev, "%s - turning break %s\n", __func__,
1059 state == BREAK_OFF ? "off" : "on");
1060 cp210x_write_u16_reg(port, CP210X_SET_BREAK, state);
1061}
1062
1063static int cp210x_port_probe(struct usb_serial_port *port)
1064{
1065 struct usb_serial *serial = port->serial;
1066 struct usb_host_interface *cur_altsetting;
1067 struct cp210x_port_private *port_priv;
1068 int ret;
1069
1070 port_priv = kzalloc(sizeof(*port_priv), GFP_KERNEL);
1071 if (!port_priv)
1072 return -ENOMEM;
1073
1074 cur_altsetting = serial->interface->cur_altsetting;
1075 port_priv->bInterfaceNumber = cur_altsetting->desc.bInterfaceNumber;
1076
1077 usb_set_serial_port_data(port, port_priv);
1078
1079 ret = cp210x_detect_swapped_line_ctl(port);
1080 if (ret) {
1081 kfree(port_priv);
1082 return ret;
1083 }
1084
1085 return 0;
1086}
1087
1088static int cp210x_port_remove(struct usb_serial_port *port)
1089{
1090 struct cp210x_port_private *port_priv;
1091
1092 port_priv = usb_get_serial_port_data(port);
1093 kfree(port_priv);
1094
1095 return 0;
1096}
1097
1098module_usb_serial_driver(serial_drivers, id_table);
1099
1100MODULE_DESCRIPTION(DRIVER_DESC);
1101MODULE_LICENSE("GPL");
1/*
2 * Silicon Laboratories CP210x USB to RS232 serial adaptor driver
3 *
4 * Copyright (C) 2005 Craig Shelley (craig@microtron.org.uk)
5 *
6 * This program is free software; you can redistribute it and/or
7 * modify it under the terms of the GNU General Public License version
8 * 2 as published by the Free Software Foundation.
9 *
10 * Support to set flow control line levels using TIOCMGET and TIOCMSET
11 * thanks to Karl Hiramoto karl@hiramoto.org. RTSCTS hardware flow
12 * control thanks to Munir Nassar nassarmu@real-time.com
13 *
14 */
15
16#include <linux/kernel.h>
17#include <linux/errno.h>
18#include <linux/slab.h>
19#include <linux/tty.h>
20#include <linux/tty_flip.h>
21#include <linux/module.h>
22#include <linux/moduleparam.h>
23#include <linux/usb.h>
24#include <linux/uaccess.h>
25#include <linux/usb/serial.h>
26
27/*
28 * Version Information
29 */
30#define DRIVER_VERSION "v0.09"
31#define DRIVER_DESC "Silicon Labs CP210x RS232 serial adaptor driver"
32
33/*
34 * Function Prototypes
35 */
36static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *);
37static void cp210x_close(struct usb_serial_port *);
38static void cp210x_get_termios(struct tty_struct *,
39 struct usb_serial_port *port);
40static void cp210x_get_termios_port(struct usb_serial_port *port,
41 unsigned int *cflagp, unsigned int *baudp);
42static void cp210x_set_termios(struct tty_struct *, struct usb_serial_port *,
43 struct ktermios*);
44static int cp210x_tiocmget(struct tty_struct *);
45static int cp210x_tiocmset(struct tty_struct *, unsigned int, unsigned int);
46static int cp210x_tiocmset_port(struct usb_serial_port *port,
47 unsigned int, unsigned int);
48static void cp210x_break_ctl(struct tty_struct *, int);
49static int cp210x_startup(struct usb_serial *);
50static void cp210x_dtr_rts(struct usb_serial_port *p, int on);
51
52static int debug;
53
54static const struct usb_device_id id_table[] = {
55 { USB_DEVICE(0x045B, 0x0053) }, /* Renesas RX610 RX-Stick */
56 { USB_DEVICE(0x0471, 0x066A) }, /* AKTAKOM ACE-1001 cable */
57 { USB_DEVICE(0x0489, 0xE000) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM Mobile */
58 { USB_DEVICE(0x0489, 0xE003) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM Mobile */
59 { USB_DEVICE(0x0745, 0x1000) }, /* CipherLab USB CCD Barcode Scanner 1000 */
60 { USB_DEVICE(0x08e6, 0x5501) }, /* Gemalto Prox-PU/CU contactless smartcard reader */
61 { USB_DEVICE(0x08FD, 0x000A) }, /* Digianswer A/S , ZigBee/802.15.4 MAC Device */
62 { USB_DEVICE(0x0BED, 0x1100) }, /* MEI (TM) Cashflow-SC Bill/Voucher Acceptor */
63 { USB_DEVICE(0x0BED, 0x1101) }, /* MEI series 2000 Combo Acceptor */
64 { USB_DEVICE(0x0FCF, 0x1003) }, /* Dynastream ANT development board */
65 { USB_DEVICE(0x0FCF, 0x1004) }, /* Dynastream ANT2USB */
66 { USB_DEVICE(0x0FCF, 0x1006) }, /* Dynastream ANT development board */
67 { USB_DEVICE(0x10A6, 0xAA26) }, /* Knock-off DCU-11 cable */
68 { USB_DEVICE(0x10AB, 0x10C5) }, /* Siemens MC60 Cable */
69 { USB_DEVICE(0x10B5, 0xAC70) }, /* Nokia CA-42 USB */
70 { USB_DEVICE(0x10C4, 0x0F91) }, /* Vstabi */
71 { USB_DEVICE(0x10C4, 0x1101) }, /* Arkham Technology DS101 Bus Monitor */
72 { USB_DEVICE(0x10C4, 0x1601) }, /* Arkham Technology DS101 Adapter */
73 { USB_DEVICE(0x10C4, 0x800A) }, /* SPORTident BSM7-D-USB main station */
74 { USB_DEVICE(0x10C4, 0x803B) }, /* Pololu USB-serial converter */
75 { USB_DEVICE(0x10C4, 0x8044) }, /* Cygnal Debug Adapter */
76 { USB_DEVICE(0x10C4, 0x804E) }, /* Software Bisque Paramount ME build-in converter */
77 { USB_DEVICE(0x10C4, 0x8053) }, /* Enfora EDG1228 */
78 { USB_DEVICE(0x10C4, 0x8054) }, /* Enfora GSM2228 */
79 { USB_DEVICE(0x10C4, 0x8066) }, /* Argussoft In-System Programmer */
80 { USB_DEVICE(0x10C4, 0x806F) }, /* IMS USB to RS422 Converter Cable */
81 { USB_DEVICE(0x10C4, 0x807A) }, /* Crumb128 board */
82 { USB_DEVICE(0x10C4, 0x80CA) }, /* Degree Controls Inc */
83 { USB_DEVICE(0x10C4, 0x80DD) }, /* Tracient RFID */
84 { USB_DEVICE(0x10C4, 0x80F6) }, /* Suunto sports instrument */
85 { USB_DEVICE(0x10C4, 0x8115) }, /* Arygon NFC/Mifare Reader */
86 { USB_DEVICE(0x10C4, 0x813D) }, /* Burnside Telecom Deskmobile */
87 { USB_DEVICE(0x10C4, 0x813F) }, /* Tams Master Easy Control */
88 { USB_DEVICE(0x10C4, 0x814A) }, /* West Mountain Radio RIGblaster P&P */
89 { USB_DEVICE(0x10C4, 0x814B) }, /* West Mountain Radio RIGtalk */
90 { USB_DEVICE(0x10C4, 0x8156) }, /* B&G H3000 link cable */
91 { USB_DEVICE(0x10C4, 0x815E) }, /* Helicomm IP-Link 1220-DVM */
92 { USB_DEVICE(0x10C4, 0x818B) }, /* AVIT Research USB to TTL */
93 { USB_DEVICE(0x10C4, 0x819F) }, /* MJS USB Toslink Switcher */
94 { USB_DEVICE(0x10C4, 0x81A6) }, /* ThinkOptics WavIt */
95 { USB_DEVICE(0x10C4, 0x81AC) }, /* MSD Dash Hawk */
96 { USB_DEVICE(0x10C4, 0x81AD) }, /* INSYS USB Modem */
97 { USB_DEVICE(0x10C4, 0x81C8) }, /* Lipowsky Industrie Elektronik GmbH, Baby-JTAG */
98 { USB_DEVICE(0x10C4, 0x81E2) }, /* Lipowsky Industrie Elektronik GmbH, Baby-LIN */
99 { USB_DEVICE(0x10C4, 0x81E7) }, /* Aerocomm Radio */
100 { USB_DEVICE(0x10C4, 0x81E8) }, /* Zephyr Bioharness */
101 { USB_DEVICE(0x10C4, 0x81F2) }, /* C1007 HF band RFID controller */
102 { USB_DEVICE(0x10C4, 0x8218) }, /* Lipowsky Industrie Elektronik GmbH, HARP-1 */
103 { USB_DEVICE(0x10C4, 0x822B) }, /* Modem EDGE(GSM) Comander 2 */
104 { USB_DEVICE(0x10C4, 0x826B) }, /* Cygnal Integrated Products, Inc., Fasttrax GPS demonstration module */
105 { USB_DEVICE(0x10C4, 0x8293) }, /* Telegesis ETRX2USB */
106 { USB_DEVICE(0x10C4, 0x82F9) }, /* Procyon AVS */
107 { USB_DEVICE(0x10C4, 0x8341) }, /* Siemens MC35PU GPRS Modem */
108 { USB_DEVICE(0x10C4, 0x8382) }, /* Cygnal Integrated Products, Inc. */
109 { USB_DEVICE(0x10C4, 0x83A8) }, /* Amber Wireless AMB2560 */
110 { USB_DEVICE(0x10C4, 0x83D8) }, /* DekTec DTA Plus VHF/UHF Booster/Attenuator */
111 { USB_DEVICE(0x10C4, 0x8411) }, /* Kyocera GPS Module */
112 { USB_DEVICE(0x10C4, 0x8418) }, /* IRZ Automation Teleport SG-10 GSM/GPRS Modem */
113 { USB_DEVICE(0x10C4, 0x846E) }, /* BEI USB Sensor Interface (VCP) */
114 { USB_DEVICE(0x10C4, 0x8477) }, /* Balluff RFID */
115 { USB_DEVICE(0x10C4, 0x85EA) }, /* AC-Services IBUS-IF */
116 { USB_DEVICE(0x10C4, 0x85EB) }, /* AC-Services CIS-IBUS */
117 { USB_DEVICE(0x10C4, 0x8664) }, /* AC-Services CAN-IF */
118 { USB_DEVICE(0x10C4, 0x8665) }, /* AC-Services OBD-IF */
119 { USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */
120 { USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */
121 { USB_DEVICE(0x10C4, 0xEA71) }, /* Infinity GPS-MIC-1 Radio Monophone */
122 { USB_DEVICE(0x10C4, 0xF001) }, /* Elan Digital Systems USBscope50 */
123 { USB_DEVICE(0x10C4, 0xF002) }, /* Elan Digital Systems USBwave12 */
124 { USB_DEVICE(0x10C4, 0xF003) }, /* Elan Digital Systems USBpulse100 */
125 { USB_DEVICE(0x10C4, 0xF004) }, /* Elan Digital Systems USBcount50 */
126 { USB_DEVICE(0x10C5, 0xEA61) }, /* Silicon Labs MobiData GPRS USB Modem */
127 { USB_DEVICE(0x10CE, 0xEA6A) }, /* Silicon Labs MobiData GPRS USB Modem 100EU */
128 { USB_DEVICE(0x13AD, 0x9999) }, /* Baltech card reader */
129 { USB_DEVICE(0x1555, 0x0004) }, /* Owen AC4 USB-RS485 Converter */
130 { USB_DEVICE(0x166A, 0x0303) }, /* Clipsal 5500PCU C-Bus USB interface */
131 { USB_DEVICE(0x16D6, 0x0001) }, /* Jablotron serial interface */
132 { USB_DEVICE(0x16DC, 0x0010) }, /* W-IE-NE-R Plein & Baus GmbH PL512 Power Supply */
133 { USB_DEVICE(0x16DC, 0x0011) }, /* W-IE-NE-R Plein & Baus GmbH RCM Remote Control for MARATON Power Supply */
134 { USB_DEVICE(0x16DC, 0x0012) }, /* W-IE-NE-R Plein & Baus GmbH MPOD Multi Channel Power Supply */
135 { USB_DEVICE(0x16DC, 0x0015) }, /* W-IE-NE-R Plein & Baus GmbH CML Control, Monitoring and Data Logger */
136 { USB_DEVICE(0x17F4, 0xAAAA) }, /* Wavesense Jazz blood glucose meter */
137 { USB_DEVICE(0x1843, 0x0200) }, /* Vaisala USB Instrument Cable */
138 { USB_DEVICE(0x18EF, 0xE00F) }, /* ELV USB-I2C-Interface */
139 { USB_DEVICE(0x1BE3, 0x07A6) }, /* WAGO 750-923 USB Service Cable */
140 { USB_DEVICE(0x413C, 0x9500) }, /* DW700 GPS USB interface */
141 { } /* Terminating Entry */
142};
143
144MODULE_DEVICE_TABLE(usb, id_table);
145
146static struct usb_driver cp210x_driver = {
147 .name = "cp210x",
148 .probe = usb_serial_probe,
149 .disconnect = usb_serial_disconnect,
150 .id_table = id_table,
151 .no_dynamic_id = 1,
152};
153
154static struct usb_serial_driver cp210x_device = {
155 .driver = {
156 .owner = THIS_MODULE,
157 .name = "cp210x",
158 },
159 .usb_driver = &cp210x_driver,
160 .id_table = id_table,
161 .num_ports = 1,
162 .bulk_in_size = 256,
163 .bulk_out_size = 256,
164 .open = cp210x_open,
165 .close = cp210x_close,
166 .break_ctl = cp210x_break_ctl,
167 .set_termios = cp210x_set_termios,
168 .tiocmget = cp210x_tiocmget,
169 .tiocmset = cp210x_tiocmset,
170 .attach = cp210x_startup,
171 .dtr_rts = cp210x_dtr_rts
172};
173
174/* Config request types */
175#define REQTYPE_HOST_TO_DEVICE 0x41
176#define REQTYPE_DEVICE_TO_HOST 0xc1
177
178/* Config request codes */
179#define CP210X_IFC_ENABLE 0x00
180#define CP210X_SET_BAUDDIV 0x01
181#define CP210X_GET_BAUDDIV 0x02
182#define CP210X_SET_LINE_CTL 0x03
183#define CP210X_GET_LINE_CTL 0x04
184#define CP210X_SET_BREAK 0x05
185#define CP210X_IMM_CHAR 0x06
186#define CP210X_SET_MHS 0x07
187#define CP210X_GET_MDMSTS 0x08
188#define CP210X_SET_XON 0x09
189#define CP210X_SET_XOFF 0x0A
190#define CP210X_SET_EVENTMASK 0x0B
191#define CP210X_GET_EVENTMASK 0x0C
192#define CP210X_SET_CHAR 0x0D
193#define CP210X_GET_CHARS 0x0E
194#define CP210X_GET_PROPS 0x0F
195#define CP210X_GET_COMM_STATUS 0x10
196#define CP210X_RESET 0x11
197#define CP210X_PURGE 0x12
198#define CP210X_SET_FLOW 0x13
199#define CP210X_GET_FLOW 0x14
200#define CP210X_EMBED_EVENTS 0x15
201#define CP210X_GET_EVENTSTATE 0x16
202#define CP210X_SET_CHARS 0x19
203
204/* CP210X_IFC_ENABLE */
205#define UART_ENABLE 0x0001
206#define UART_DISABLE 0x0000
207
208/* CP210X_(SET|GET)_BAUDDIV */
209#define BAUD_RATE_GEN_FREQ 0x384000
210
211/* CP210X_(SET|GET)_LINE_CTL */
212#define BITS_DATA_MASK 0X0f00
213#define BITS_DATA_5 0X0500
214#define BITS_DATA_6 0X0600
215#define BITS_DATA_7 0X0700
216#define BITS_DATA_8 0X0800
217#define BITS_DATA_9 0X0900
218
219#define BITS_PARITY_MASK 0x00f0
220#define BITS_PARITY_NONE 0x0000
221#define BITS_PARITY_ODD 0x0010
222#define BITS_PARITY_EVEN 0x0020
223#define BITS_PARITY_MARK 0x0030
224#define BITS_PARITY_SPACE 0x0040
225
226#define BITS_STOP_MASK 0x000f
227#define BITS_STOP_1 0x0000
228#define BITS_STOP_1_5 0x0001
229#define BITS_STOP_2 0x0002
230
231/* CP210X_SET_BREAK */
232#define BREAK_ON 0x0001
233#define BREAK_OFF 0x0000
234
235/* CP210X_(SET_MHS|GET_MDMSTS) */
236#define CONTROL_DTR 0x0001
237#define CONTROL_RTS 0x0002
238#define CONTROL_CTS 0x0010
239#define CONTROL_DSR 0x0020
240#define CONTROL_RING 0x0040
241#define CONTROL_DCD 0x0080
242#define CONTROL_WRITE_DTR 0x0100
243#define CONTROL_WRITE_RTS 0x0200
244
245/*
246 * cp210x_get_config
247 * Reads from the CP210x configuration registers
248 * 'size' is specified in bytes.
249 * 'data' is a pointer to a pre-allocated array of integers large
250 * enough to hold 'size' bytes (with 4 bytes to each integer)
251 */
252static int cp210x_get_config(struct usb_serial_port *port, u8 request,
253 unsigned int *data, int size)
254{
255 struct usb_serial *serial = port->serial;
256 __le32 *buf;
257 int result, i, length;
258
259 /* Number of integers required to contain the array */
260 length = (((size - 1) | 3) + 1)/4;
261
262 buf = kcalloc(length, sizeof(__le32), GFP_KERNEL);
263 if (!buf) {
264 dev_err(&port->dev, "%s - out of memory.\n", __func__);
265 return -ENOMEM;
266 }
267
268 /* Issue the request, attempting to read 'size' bytes */
269 result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
270 request, REQTYPE_DEVICE_TO_HOST, 0x0000,
271 0, buf, size, 300);
272
273 /* Convert data into an array of integers */
274 for (i = 0; i < length; i++)
275 data[i] = le32_to_cpu(buf[i]);
276
277 kfree(buf);
278
279 if (result != size) {
280 dbg("%s - Unable to send config request, "
281 "request=0x%x size=%d result=%d\n",
282 __func__, request, size, result);
283 return -EPROTO;
284 }
285
286 return 0;
287}
288
289/*
290 * cp210x_set_config
291 * Writes to the CP210x configuration registers
292 * Values less than 16 bits wide are sent directly
293 * 'size' is specified in bytes.
294 */
295static int cp210x_set_config(struct usb_serial_port *port, u8 request,
296 unsigned int *data, int size)
297{
298 struct usb_serial *serial = port->serial;
299 __le32 *buf;
300 int result, i, length;
301
302 /* Number of integers required to contain the array */
303 length = (((size - 1) | 3) + 1)/4;
304
305 buf = kmalloc(length * sizeof(__le32), GFP_KERNEL);
306 if (!buf) {
307 dev_err(&port->dev, "%s - out of memory.\n",
308 __func__);
309 return -ENOMEM;
310 }
311
312 /* Array of integers into bytes */
313 for (i = 0; i < length; i++)
314 buf[i] = cpu_to_le32(data[i]);
315
316 if (size > 2) {
317 result = usb_control_msg(serial->dev,
318 usb_sndctrlpipe(serial->dev, 0),
319 request, REQTYPE_HOST_TO_DEVICE, 0x0000,
320 0, buf, size, 300);
321 } else {
322 result = usb_control_msg(serial->dev,
323 usb_sndctrlpipe(serial->dev, 0),
324 request, REQTYPE_HOST_TO_DEVICE, data[0],
325 0, NULL, 0, 300);
326 }
327
328 kfree(buf);
329
330 if ((size > 2 && result != size) || result < 0) {
331 dbg("%s - Unable to send request, "
332 "request=0x%x size=%d result=%d\n",
333 __func__, request, size, result);
334 return -EPROTO;
335 }
336
337 return 0;
338}
339
340/*
341 * cp210x_set_config_single
342 * Convenience function for calling cp210x_set_config on single data values
343 * without requiring an integer pointer
344 */
345static inline int cp210x_set_config_single(struct usb_serial_port *port,
346 u8 request, unsigned int data)
347{
348 return cp210x_set_config(port, request, &data, 2);
349}
350
351/*
352 * cp210x_quantise_baudrate
353 * Quantises the baud rate as per AN205 Table 1
354 */
355static unsigned int cp210x_quantise_baudrate(unsigned int baud) {
356 if (baud <= 56) baud = 0;
357 else if (baud <= 300) baud = 300;
358 else if (baud <= 600) baud = 600;
359 else if (baud <= 1200) baud = 1200;
360 else if (baud <= 1800) baud = 1800;
361 else if (baud <= 2400) baud = 2400;
362 else if (baud <= 4000) baud = 4000;
363 else if (baud <= 4803) baud = 4800;
364 else if (baud <= 7207) baud = 7200;
365 else if (baud <= 9612) baud = 9600;
366 else if (baud <= 14428) baud = 14400;
367 else if (baud <= 16062) baud = 16000;
368 else if (baud <= 19250) baud = 19200;
369 else if (baud <= 28912) baud = 28800;
370 else if (baud <= 38601) baud = 38400;
371 else if (baud <= 51558) baud = 51200;
372 else if (baud <= 56280) baud = 56000;
373 else if (baud <= 58053) baud = 57600;
374 else if (baud <= 64111) baud = 64000;
375 else if (baud <= 77608) baud = 76800;
376 else if (baud <= 117028) baud = 115200;
377 else if (baud <= 129347) baud = 128000;
378 else if (baud <= 156868) baud = 153600;
379 else if (baud <= 237832) baud = 230400;
380 else if (baud <= 254234) baud = 250000;
381 else if (baud <= 273066) baud = 256000;
382 else if (baud <= 491520) baud = 460800;
383 else if (baud <= 567138) baud = 500000;
384 else if (baud <= 670254) baud = 576000;
385 else if (baud <= 1053257) baud = 921600;
386 else if (baud <= 1474560) baud = 1228800;
387 else if (baud <= 2457600) baud = 1843200;
388 else baud = 3686400;
389 return baud;
390}
391
392static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *port)
393{
394 int result;
395
396 dbg("%s - port %d", __func__, port->number);
397
398 if (cp210x_set_config_single(port, CP210X_IFC_ENABLE, UART_ENABLE)) {
399 dev_err(&port->dev, "%s - Unable to enable UART\n",
400 __func__);
401 return -EPROTO;
402 }
403
404 result = usb_serial_generic_open(tty, port);
405 if (result)
406 return result;
407
408 /* Configure the termios structure */
409 cp210x_get_termios(tty, port);
410 return 0;
411}
412
413static void cp210x_close(struct usb_serial_port *port)
414{
415 dbg("%s - port %d", __func__, port->number);
416
417 usb_serial_generic_close(port);
418
419 mutex_lock(&port->serial->disc_mutex);
420 if (!port->serial->disconnected)
421 cp210x_set_config_single(port, CP210X_IFC_ENABLE, UART_DISABLE);
422 mutex_unlock(&port->serial->disc_mutex);
423}
424
425/*
426 * cp210x_get_termios
427 * Reads the baud rate, data bits, parity, stop bits and flow control mode
428 * from the device, corrects any unsupported values, and configures the
429 * termios structure to reflect the state of the device
430 */
431static void cp210x_get_termios(struct tty_struct *tty,
432 struct usb_serial_port *port)
433{
434 unsigned int baud;
435
436 if (tty) {
437 cp210x_get_termios_port(tty->driver_data,
438 &tty->termios->c_cflag, &baud);
439 tty_encode_baud_rate(tty, baud, baud);
440 }
441
442 else {
443 unsigned int cflag;
444 cflag = 0;
445 cp210x_get_termios_port(port, &cflag, &baud);
446 }
447}
448
449/*
450 * cp210x_get_termios_port
451 * This is the heart of cp210x_get_termios which always uses a &usb_serial_port.
452 */
453static void cp210x_get_termios_port(struct usb_serial_port *port,
454 unsigned int *cflagp, unsigned int *baudp)
455{
456 unsigned int cflag, modem_ctl[4];
457 unsigned int baud;
458 unsigned int bits;
459
460 dbg("%s - port %d", __func__, port->number);
461
462 cp210x_get_config(port, CP210X_GET_BAUDDIV, &baud, 2);
463 /* Convert to baudrate */
464 if (baud)
465 baud = cp210x_quantise_baudrate((BAUD_RATE_GEN_FREQ + baud/2)/ baud);
466
467 dbg("%s - baud rate = %d", __func__, baud);
468 *baudp = baud;
469
470 cflag = *cflagp;
471
472 cp210x_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
473 cflag &= ~CSIZE;
474 switch (bits & BITS_DATA_MASK) {
475 case BITS_DATA_5:
476 dbg("%s - data bits = 5", __func__);
477 cflag |= CS5;
478 break;
479 case BITS_DATA_6:
480 dbg("%s - data bits = 6", __func__);
481 cflag |= CS6;
482 break;
483 case BITS_DATA_7:
484 dbg("%s - data bits = 7", __func__);
485 cflag |= CS7;
486 break;
487 case BITS_DATA_8:
488 dbg("%s - data bits = 8", __func__);
489 cflag |= CS8;
490 break;
491 case BITS_DATA_9:
492 dbg("%s - data bits = 9 (not supported, using 8 data bits)",
493 __func__);
494 cflag |= CS8;
495 bits &= ~BITS_DATA_MASK;
496 bits |= BITS_DATA_8;
497 cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
498 break;
499 default:
500 dbg("%s - Unknown number of data bits, using 8", __func__);
501 cflag |= CS8;
502 bits &= ~BITS_DATA_MASK;
503 bits |= BITS_DATA_8;
504 cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
505 break;
506 }
507
508 switch (bits & BITS_PARITY_MASK) {
509 case BITS_PARITY_NONE:
510 dbg("%s - parity = NONE", __func__);
511 cflag &= ~PARENB;
512 break;
513 case BITS_PARITY_ODD:
514 dbg("%s - parity = ODD", __func__);
515 cflag |= (PARENB|PARODD);
516 break;
517 case BITS_PARITY_EVEN:
518 dbg("%s - parity = EVEN", __func__);
519 cflag &= ~PARODD;
520 cflag |= PARENB;
521 break;
522 case BITS_PARITY_MARK:
523 dbg("%s - parity = MARK (not supported, disabling parity)",
524 __func__);
525 cflag &= ~PARENB;
526 bits &= ~BITS_PARITY_MASK;
527 cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
528 break;
529 case BITS_PARITY_SPACE:
530 dbg("%s - parity = SPACE (not supported, disabling parity)",
531 __func__);
532 cflag &= ~PARENB;
533 bits &= ~BITS_PARITY_MASK;
534 cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
535 break;
536 default:
537 dbg("%s - Unknown parity mode, disabling parity", __func__);
538 cflag &= ~PARENB;
539 bits &= ~BITS_PARITY_MASK;
540 cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
541 break;
542 }
543
544 cflag &= ~CSTOPB;
545 switch (bits & BITS_STOP_MASK) {
546 case BITS_STOP_1:
547 dbg("%s - stop bits = 1", __func__);
548 break;
549 case BITS_STOP_1_5:
550 dbg("%s - stop bits = 1.5 (not supported, using 1 stop bit)",
551 __func__);
552 bits &= ~BITS_STOP_MASK;
553 cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
554 break;
555 case BITS_STOP_2:
556 dbg("%s - stop bits = 2", __func__);
557 cflag |= CSTOPB;
558 break;
559 default:
560 dbg("%s - Unknown number of stop bits, using 1 stop bit",
561 __func__);
562 bits &= ~BITS_STOP_MASK;
563 cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
564 break;
565 }
566
567 cp210x_get_config(port, CP210X_GET_FLOW, modem_ctl, 16);
568 if (modem_ctl[0] & 0x0008) {
569 dbg("%s - flow control = CRTSCTS", __func__);
570 cflag |= CRTSCTS;
571 } else {
572 dbg("%s - flow control = NONE", __func__);
573 cflag &= ~CRTSCTS;
574 }
575
576 *cflagp = cflag;
577}
578
579static void cp210x_set_termios(struct tty_struct *tty,
580 struct usb_serial_port *port, struct ktermios *old_termios)
581{
582 unsigned int cflag, old_cflag;
583 unsigned int baud = 0, bits;
584 unsigned int modem_ctl[4];
585
586 dbg("%s - port %d", __func__, port->number);
587
588 if (!tty)
589 return;
590
591 tty->termios->c_cflag &= ~CMSPAR;
592 cflag = tty->termios->c_cflag;
593 old_cflag = old_termios->c_cflag;
594 baud = cp210x_quantise_baudrate(tty_get_baud_rate(tty));
595
596 /* If the baud rate is to be updated*/
597 if (baud != tty_termios_baud_rate(old_termios) && baud != 0) {
598 dbg("%s - Setting baud rate to %d baud", __func__,
599 baud);
600 if (cp210x_set_config_single(port, CP210X_SET_BAUDDIV,
601 ((BAUD_RATE_GEN_FREQ + baud/2) / baud))) {
602 dbg("Baud rate requested not supported by device");
603 baud = tty_termios_baud_rate(old_termios);
604 }
605 }
606 /* Report back the resulting baud rate */
607 tty_encode_baud_rate(tty, baud, baud);
608
609 /* If the number of data bits is to be updated */
610 if ((cflag & CSIZE) != (old_cflag & CSIZE)) {
611 cp210x_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
612 bits &= ~BITS_DATA_MASK;
613 switch (cflag & CSIZE) {
614 case CS5:
615 bits |= BITS_DATA_5;
616 dbg("%s - data bits = 5", __func__);
617 break;
618 case CS6:
619 bits |= BITS_DATA_6;
620 dbg("%s - data bits = 6", __func__);
621 break;
622 case CS7:
623 bits |= BITS_DATA_7;
624 dbg("%s - data bits = 7", __func__);
625 break;
626 case CS8:
627 bits |= BITS_DATA_8;
628 dbg("%s - data bits = 8", __func__);
629 break;
630 /*case CS9:
631 bits |= BITS_DATA_9;
632 dbg("%s - data bits = 9", __func__);
633 break;*/
634 default:
635 dbg("cp210x driver does not "
636 "support the number of bits requested,"
637 " using 8 bit mode\n");
638 bits |= BITS_DATA_8;
639 break;
640 }
641 if (cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
642 dbg("Number of data bits requested "
643 "not supported by device\n");
644 }
645
646 if ((cflag & (PARENB|PARODD)) != (old_cflag & (PARENB|PARODD))) {
647 cp210x_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
648 bits &= ~BITS_PARITY_MASK;
649 if (cflag & PARENB) {
650 if (cflag & PARODD) {
651 bits |= BITS_PARITY_ODD;
652 dbg("%s - parity = ODD", __func__);
653 } else {
654 bits |= BITS_PARITY_EVEN;
655 dbg("%s - parity = EVEN", __func__);
656 }
657 }
658 if (cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
659 dbg("Parity mode not supported "
660 "by device\n");
661 }
662
663 if ((cflag & CSTOPB) != (old_cflag & CSTOPB)) {
664 cp210x_get_config(port, CP210X_GET_LINE_CTL, &bits, 2);
665 bits &= ~BITS_STOP_MASK;
666 if (cflag & CSTOPB) {
667 bits |= BITS_STOP_2;
668 dbg("%s - stop bits = 2", __func__);
669 } else {
670 bits |= BITS_STOP_1;
671 dbg("%s - stop bits = 1", __func__);
672 }
673 if (cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
674 dbg("Number of stop bits requested "
675 "not supported by device\n");
676 }
677
678 if ((cflag & CRTSCTS) != (old_cflag & CRTSCTS)) {
679 cp210x_get_config(port, CP210X_GET_FLOW, modem_ctl, 16);
680 dbg("%s - read modem controls = 0x%.4x 0x%.4x 0x%.4x 0x%.4x",
681 __func__, modem_ctl[0], modem_ctl[1],
682 modem_ctl[2], modem_ctl[3]);
683
684 if (cflag & CRTSCTS) {
685 modem_ctl[0] &= ~0x7B;
686 modem_ctl[0] |= 0x09;
687 modem_ctl[1] = 0x80;
688 dbg("%s - flow control = CRTSCTS", __func__);
689 } else {
690 modem_ctl[0] &= ~0x7B;
691 modem_ctl[0] |= 0x01;
692 modem_ctl[1] |= 0x40;
693 dbg("%s - flow control = NONE", __func__);
694 }
695
696 dbg("%s - write modem controls = 0x%.4x 0x%.4x 0x%.4x 0x%.4x",
697 __func__, modem_ctl[0], modem_ctl[1],
698 modem_ctl[2], modem_ctl[3]);
699 cp210x_set_config(port, CP210X_SET_FLOW, modem_ctl, 16);
700 }
701
702}
703
704static int cp210x_tiocmset (struct tty_struct *tty,
705 unsigned int set, unsigned int clear)
706{
707 struct usb_serial_port *port = tty->driver_data;
708 return cp210x_tiocmset_port(port, set, clear);
709}
710
711static int cp210x_tiocmset_port(struct usb_serial_port *port,
712 unsigned int set, unsigned int clear)
713{
714 unsigned int control = 0;
715
716 dbg("%s - port %d", __func__, port->number);
717
718 if (set & TIOCM_RTS) {
719 control |= CONTROL_RTS;
720 control |= CONTROL_WRITE_RTS;
721 }
722 if (set & TIOCM_DTR) {
723 control |= CONTROL_DTR;
724 control |= CONTROL_WRITE_DTR;
725 }
726 if (clear & TIOCM_RTS) {
727 control &= ~CONTROL_RTS;
728 control |= CONTROL_WRITE_RTS;
729 }
730 if (clear & TIOCM_DTR) {
731 control &= ~CONTROL_DTR;
732 control |= CONTROL_WRITE_DTR;
733 }
734
735 dbg("%s - control = 0x%.4x", __func__, control);
736
737 return cp210x_set_config(port, CP210X_SET_MHS, &control, 2);
738}
739
740static void cp210x_dtr_rts(struct usb_serial_port *p, int on)
741{
742 if (on)
743 cp210x_tiocmset_port(p, TIOCM_DTR|TIOCM_RTS, 0);
744 else
745 cp210x_tiocmset_port(p, 0, TIOCM_DTR|TIOCM_RTS);
746}
747
748static int cp210x_tiocmget (struct tty_struct *tty)
749{
750 struct usb_serial_port *port = tty->driver_data;
751 unsigned int control;
752 int result;
753
754 dbg("%s - port %d", __func__, port->number);
755
756 cp210x_get_config(port, CP210X_GET_MDMSTS, &control, 1);
757
758 result = ((control & CONTROL_DTR) ? TIOCM_DTR : 0)
759 |((control & CONTROL_RTS) ? TIOCM_RTS : 0)
760 |((control & CONTROL_CTS) ? TIOCM_CTS : 0)
761 |((control & CONTROL_DSR) ? TIOCM_DSR : 0)
762 |((control & CONTROL_RING)? TIOCM_RI : 0)
763 |((control & CONTROL_DCD) ? TIOCM_CD : 0);
764
765 dbg("%s - control = 0x%.2x", __func__, control);
766
767 return result;
768}
769
770static void cp210x_break_ctl (struct tty_struct *tty, int break_state)
771{
772 struct usb_serial_port *port = tty->driver_data;
773 unsigned int state;
774
775 dbg("%s - port %d", __func__, port->number);
776 if (break_state == 0)
777 state = BREAK_OFF;
778 else
779 state = BREAK_ON;
780 dbg("%s - turning break %s", __func__,
781 state == BREAK_OFF ? "off" : "on");
782 cp210x_set_config(port, CP210X_SET_BREAK, &state, 2);
783}
784
785static int cp210x_startup(struct usb_serial *serial)
786{
787 /* cp210x buffers behave strangely unless device is reset */
788 usb_reset_device(serial->dev);
789 return 0;
790}
791
792static int __init cp210x_init(void)
793{
794 int retval;
795
796 retval = usb_serial_register(&cp210x_device);
797 if (retval)
798 return retval; /* Failed to register */
799
800 retval = usb_register(&cp210x_driver);
801 if (retval) {
802 /* Failed to register */
803 usb_serial_deregister(&cp210x_device);
804 return retval;
805 }
806
807 /* Success */
808 printk(KERN_INFO KBUILD_MODNAME ": " DRIVER_VERSION ":"
809 DRIVER_DESC "\n");
810 return 0;
811}
812
813static void __exit cp210x_exit(void)
814{
815 usb_deregister(&cp210x_driver);
816 usb_serial_deregister(&cp210x_device);
817}
818
819module_init(cp210x_init);
820module_exit(cp210x_exit);
821
822MODULE_DESCRIPTION(DRIVER_DESC);
823MODULE_VERSION(DRIVER_VERSION);
824MODULE_LICENSE("GPL");
825
826module_param(debug, bool, S_IRUGO | S_IWUSR);
827MODULE_PARM_DESC(debug, "Enable verbose debugging messages");