Loading...
Note: File does not exist in v6.9.4.
1// SPDX-License-Identifier: GPL-2.0
2#include <dt-bindings/input/input.h>
3#include "tegra124.dtsi"
4
5/ {
6 aliases {
7 rtc0 = "/i2c@7000d000/pmic@40";
8 rtc1 = "/rtc@7000e000";
9 serial0 = &uarta;
10 };
11
12 chosen {
13 stdout-path = "serial0:115200n8";
14 };
15
16 memory {
17 reg = <0x0 0x80000000 0x0 0x80000000>;
18 };
19
20 host1x@50000000 {
21 hdmi@54280000 {
22 status = "okay";
23
24 vdd-supply = <&vdd_3v3_hdmi>;
25 pll-supply = <&vdd_hdmi_pll>;
26 hdmi-supply = <&vdd_5v0_hdmi>;
27
28 nvidia,ddc-i2c-bus = <&hdmi_ddc>;
29 nvidia,hpd-gpio =
30 <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
31 };
32
33 sor@54540000 {
34 status = "okay";
35
36 nvidia,dpaux = <&dpaux>;
37 nvidia,panel = <&panel>;
38 };
39
40 dpaux@545c0000 {
41 vdd-supply = <&vdd_3v3_panel>;
42 status = "okay";
43 };
44 };
45
46 gpu@0,57000000 {
47 status = "okay";
48
49 vdd-supply = <&vdd_gpu>;
50 };
51
52 serial@70006000 {
53 /* Debug connector on the bottom of the board near SD card. */
54 status = "okay";
55 };
56
57 pwm@7000a000 {
58 status = "okay";
59 };
60
61 i2c@7000c000 {
62 status = "okay";
63 clock-frequency = <100000>;
64
65 acodec: audio-codec@10 {
66 compatible = "maxim,max98090";
67 reg = <0x10>;
68 interrupt-parent = <&gpio>;
69 interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_EDGE_FALLING>;
70 };
71
72 temperature-sensor@4c {
73 compatible = "ti,tmp451";
74 reg = <0x4c>;
75 interrupt-parent = <&gpio>;
76 interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
77
78 #thermal-sensor-cells = <1>;
79 };
80 };
81
82 i2c@7000c400 {
83 status = "okay";
84 clock-frequency = <100000>;
85
86 trackpad@15 {
87 compatible = "elan,ekth3000";
88 reg = <0x15>;
89 interrupt-parent = <&gpio>;
90 interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_EDGE_FALLING>;
91 wakeup-source;
92 };
93 };
94
95 i2c@7000c500 {
96 status = "okay";
97 clock-frequency = <400000>;
98
99 tpm@20 {
100 compatible = "infineon,slb9645tt";
101 reg = <0x20>;
102 };
103 };
104
105 hdmi_ddc: i2c@7000c700 {
106 status = "okay";
107 clock-frequency = <100000>;
108 };
109
110 i2c@7000d000 {
111 status = "okay";
112 clock-frequency = <400000>;
113
114 pmic: pmic@40 {
115 compatible = "ams,as3722";
116 reg = <0x40>;
117 interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
118
119 ams,system-power-controller;
120
121 #interrupt-cells = <2>;
122 interrupt-controller;
123
124 gpio-controller;
125 #gpio-cells = <2>;
126
127 pinctrl-names = "default";
128 pinctrl-0 = <&as3722_default>;
129
130 as3722_default: pinmux {
131 gpio0 {
132 pins = "gpio0";
133 function = "gpio";
134 bias-pull-down;
135 };
136
137 gpio1 {
138 pins = "gpio1";
139 function = "gpio";
140 bias-pull-up;
141 };
142
143 gpio2_4_7 {
144 pins = "gpio2", "gpio4", "gpio7";
145 function = "gpio";
146 bias-pull-up;
147 };
148
149 gpio3_6 {
150 pins = "gpio3", "gpio6";
151 bias-high-impedance;
152 };
153
154 gpio5 {
155 pins = "gpio5";
156 function = "clk32k-out";
157 bias-pull-down;
158 };
159 };
160
161 regulators {
162 vsup-sd2-supply = <&vdd_5v0_sys>;
163 vsup-sd3-supply = <&vdd_5v0_sys>;
164 vsup-sd4-supply = <&vdd_5v0_sys>;
165 vsup-sd5-supply = <&vdd_5v0_sys>;
166 vin-ldo0-supply = <&vdd_1v35_lp0>;
167 vin-ldo1-6-supply = <&vdd_3v3_run>;
168 vin-ldo2-5-7-supply = <&vddio_1v8>;
169 vin-ldo3-4-supply = <&vdd_3v3_sys>;
170 vin-ldo9-10-supply = <&vdd_5v0_sys>;
171 vin-ldo11-supply = <&vdd_3v3_run>;
172
173 vdd_cpu: sd0 {
174 regulator-name = "+VDD_CPU_AP";
175 regulator-min-microvolt = <700000>;
176 regulator-max-microvolt = <1350000>;
177 regulator-min-microamp = <3500000>;
178 regulator-max-microamp = <3500000>;
179 regulator-always-on;
180 regulator-boot-on;
181 ams,ext-control = <2>;
182 };
183
184 sd1 {
185 regulator-name = "+VDD_CORE";
186 regulator-min-microvolt = <700000>;
187 regulator-max-microvolt = <1350000>;
188 regulator-min-microamp = <2500000>;
189 regulator-max-microamp = <4000000>;
190 regulator-always-on;
191 regulator-boot-on;
192 ams,ext-control = <1>;
193 };
194
195 vdd_1v35_lp0: sd2 {
196 regulator-name = "+1.35V_LP0(sd2)";
197 regulator-min-microvolt = <1350000>;
198 regulator-max-microvolt = <1350000>;
199 regulator-always-on;
200 regulator-boot-on;
201 };
202
203 sd3 {
204 regulator-name = "+1.35V_LP0(sd3)";
205 regulator-min-microvolt = <1350000>;
206 regulator-max-microvolt = <1350000>;
207 regulator-always-on;
208 regulator-boot-on;
209 };
210
211 vdd_1v05_run: sd4 {
212 regulator-name = "+1.05V_RUN";
213 regulator-min-microvolt = <1050000>;
214 regulator-max-microvolt = <1050000>;
215 };
216
217 vddio_1v8: sd5 {
218 regulator-name = "+1.8V_VDDIO";
219 regulator-min-microvolt = <1800000>;
220 regulator-max-microvolt = <1800000>;
221 regulator-always-on;
222 };
223
224 vdd_gpu: sd6 {
225 regulator-name = "+VDD_GPU_AP";
226 regulator-min-microvolt = <650000>;
227 regulator-max-microvolt = <1200000>;
228 regulator-min-microamp = <3500000>;
229 regulator-max-microamp = <3500000>;
230 regulator-boot-on;
231 regulator-always-on;
232 };
233
234 avdd_1v05_run: ldo0 {
235 regulator-name = "+1.05V_RUN_AVDD";
236 regulator-min-microvolt = <1050000>;
237 regulator-max-microvolt = <1050000>;
238 regulator-boot-on;
239 regulator-always-on;
240 ams,ext-control = <1>;
241 };
242
243 ldo1 {
244 regulator-name = "+1.8V_RUN_CAM";
245 regulator-min-microvolt = <1800000>;
246 regulator-max-microvolt = <1800000>;
247 };
248
249 ldo2 {
250 regulator-name = "+1.2V_GEN_AVDD";
251 regulator-min-microvolt = <1200000>;
252 regulator-max-microvolt = <1200000>;
253 regulator-boot-on;
254 regulator-always-on;
255 };
256
257 ldo3 {
258 regulator-name = "+1.00V_LP0_VDD_RTC";
259 regulator-min-microvolt = <1000000>;
260 regulator-max-microvolt = <1000000>;
261 regulator-boot-on;
262 regulator-always-on;
263 ams,enable-tracking;
264 };
265
266 vdd_run_cam: ldo4 {
267 regulator-name = "+3.3V_RUN_CAM";
268 regulator-min-microvolt = <2800000>;
269 regulator-max-microvolt = <2800000>;
270 };
271
272 ldo5 {
273 regulator-name = "+1.2V_RUN_CAM_FRONT";
274 regulator-min-microvolt = <1200000>;
275 regulator-max-microvolt = <1200000>;
276 };
277
278 vddio_sdmmc3: ldo6 {
279 regulator-name = "+VDDIO_SDMMC3";
280 regulator-min-microvolt = <1800000>;
281 regulator-max-microvolt = <3300000>;
282 };
283
284 ldo7 {
285 regulator-name = "+1.05V_RUN_CAM_REAR";
286 regulator-min-microvolt = <1050000>;
287 regulator-max-microvolt = <1050000>;
288 };
289
290 ldo9 {
291 regulator-name = "+2.8V_RUN_TOUCH";
292 regulator-min-microvolt = <2800000>;
293 regulator-max-microvolt = <2800000>;
294 };
295
296 ldo10 {
297 regulator-name = "+2.8V_RUN_CAM_AF";
298 regulator-min-microvolt = <2800000>;
299 regulator-max-microvolt = <2800000>;
300 };
301
302 ldo11 {
303 regulator-name = "+1.8V_RUN_VPP_FUSE";
304 regulator-min-microvolt = <1800000>;
305 regulator-max-microvolt = <1800000>;
306 };
307 };
308 };
309 };
310
311 spi@7000d400 {
312 status = "okay";
313
314 cros_ec: cros-ec@0 {
315 compatible = "google,cros-ec-spi";
316 spi-max-frequency = <3000000>;
317 interrupt-parent = <&gpio>;
318 interrupts = <TEGRA_GPIO(C, 7) IRQ_TYPE_LEVEL_LOW>;
319 reg = <0>;
320
321 google,cros-ec-spi-msg-delay = <2000>;
322
323 i2c-tunnel {
324 compatible = "google,cros-ec-i2c-tunnel";
325 #address-cells = <1>;
326 #size-cells = <0>;
327
328 google,remote-bus = <0>;
329
330 charger: bq24735@9 {
331 compatible = "ti,bq24735";
332 reg = <0x9>;
333 interrupt-parent = <&gpio>;
334 interrupts = <TEGRA_GPIO(J, 0)
335 IRQ_TYPE_EDGE_BOTH>;
336 ti,ac-detect-gpios = <&gpio
337 TEGRA_GPIO(J, 0)
338 GPIO_ACTIVE_HIGH>;
339 ti,external-control;
340 };
341
342 battery: sbs-battery@b {
343 compatible = "sbs,sbs-battery";
344 reg = <0xb>;
345 sbs,i2c-retry-count = <2>;
346 sbs,poll-retry-count = <10>;
347 power-supplies = <&charger>;
348 };
349 };
350 };
351 };
352
353 spi@7000da00 {
354 status = "okay";
355 spi-max-frequency = <25000000>;
356
357 flash@0 {
358 compatible = "winbond,w25q32dw";
359 spi-max-frequency = <25000000>;
360 reg = <0>;
361 };
362 };
363
364 pmc@7000e400 {
365 nvidia,invert-interrupt;
366 nvidia,suspend-mode = <0>;
367 nvidia,cpu-pwr-good-time = <500>;
368 nvidia,cpu-pwr-off-time = <300>;
369 nvidia,core-pwr-good-time = <641 3845>;
370 nvidia,core-pwr-off-time = <61036>;
371 nvidia,core-power-req-active-high;
372 nvidia,sys-clock-req-active-high;
373 };
374
375 hda@70030000 {
376 status = "okay";
377 };
378
379 usb@70090000 {
380 phys = <&{/padctl@7009f000/pads/usb2/lanes/usb2-0}>, /* 1st USB A */
381 <&{/padctl@7009f000/pads/usb2/lanes/usb2-1}>, /* Internal USB */
382 <&{/padctl@7009f000/pads/usb2/lanes/usb2-2}>, /* 2nd USB A */
383 <&{/padctl@7009f000/pads/pcie/lanes/pcie-0}>, /* 1st USB A */
384 <&{/padctl@7009f000/pads/pcie/lanes/pcie-1}>; /* 2nd USB A */
385 phy-names = "usb2-0", "usb2-1", "usb2-2", "usb3-0", "usb3-1";
386
387 avddio-pex-supply = <&vdd_1v05_run>;
388 dvddio-pex-supply = <&vdd_1v05_run>;
389 avdd-usb-supply = <&vdd_3v3_lp0>;
390 avdd-pll-utmip-supply = <&vddio_1v8>;
391 avdd-pll-erefe-supply = <&avdd_1v05_run>;
392 avdd-usb-ss-pll-supply = <&vdd_1v05_run>;
393 hvdd-usb-ss-supply = <&vdd_3v3_lp0>;
394 hvdd-usb-ss-pll-e-supply = <&vdd_3v3_lp0>;
395
396 status = "okay";
397 };
398
399 padctl@7009f000 {
400 status = "okay";
401
402 pads {
403 usb2 {
404 status = "okay";
405
406 lanes {
407 usb2-0 {
408 nvidia,function = "xusb";
409 status = "okay";
410 };
411
412 usb2-1 {
413 nvidia,function = "xusb";
414 status = "okay";
415 };
416
417 usb2-2 {
418 nvidia,function = "xusb";
419 status = "okay";
420 };
421 };
422 };
423
424 pcie {
425 status = "okay";
426
427 lanes {
428 pcie-0 {
429 nvidia,function = "usb3-ss";
430 status = "okay";
431 };
432
433 pcie-1 {
434 nvidia,function = "usb3-ss";
435 status = "okay";
436 };
437 };
438 };
439 };
440
441 ports {
442 usb2-0 {
443 vbus-supply = <&vdd_usb1_vbus>;
444 status = "okay";
445 mode = "otg";
446 };
447
448 usb2-1 {
449 vbus-supply = <&vdd_run_cam>;
450 status = "okay";
451 mode = "host";
452 };
453
454 usb2-2 {
455 vbus-supply = <&vdd_usb3_vbus>;
456 status = "okay";
457 mode = "host";
458 };
459
460 usb3-0 {
461 nvidia,usb2-companion = <0>;
462 status = "okay";
463 };
464
465 usb3-1 {
466 nvidia,usb2-companion = <1>;
467 status = "okay";
468 };
469 };
470 };
471
472 sdhci0_pwrseq: sdhci0_pwrseq {
473 compatible = "mmc-pwrseq-simple";
474
475 reset-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
476 };
477
478 sdhci@700b0000 { /* WiFi/BT on this bus */
479 status = "okay";
480 bus-width = <4>;
481 no-1-8-v;
482 non-removable;
483 mmc-pwrseq = <&sdhci0_pwrseq>;
484 vmmc-supply = <&vdd_3v3_lp0>;
485 vqmmc-supply = <&vddio_1v8>;
486 keep-power-in-suspend;
487 };
488
489 sdhci@700b0400 { /* SD Card on this bus */
490 status = "okay";
491 cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
492 power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
493 bus-width = <4>;
494 no-1-8-v;
495 vqmmc-supply = <&vddio_sdmmc3>;
496 };
497
498 sdhci@700b0600 { /* eMMC on this bus */
499 status = "okay";
500 bus-width = <8>;
501 no-1-8-v;
502 non-removable;
503 };
504
505 /* CPU DFLL clock */
506 clock@70110000 {
507 status = "disabled";
508 vdd-cpu-supply = <&vdd_cpu>;
509 nvidia,i2c-fs-rate = <400000>;
510 };
511
512 ahub@70300000 {
513 i2s@70301100 {
514 status = "okay";
515 };
516 };
517
518 backlight: backlight {
519 compatible = "pwm-backlight";
520
521 enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
522 power-supply = <&vdd_led>;
523 pwms = <&pwm 1 1000000>;
524
525 default-brightness-level = <224>;
526 brightness-levels =
527 < 0 1 2 3 4 5 6 7
528 8 9 10 11 12 13 14 15
529 16 17 18 19 20 21 22 23
530 24 25 26 27 28 29 30 31
531 32 33 34 35 36 37 38 39
532 40 41 42 43 44 45 46 47
533 48 49 50 51 52 53 54 55
534 56 57 58 59 60 61 62 63
535 64 65 66 67 68 69 70 71
536 72 73 74 75 76 77 78 79
537 80 81 82 83 84 85 86 87
538 88 89 90 91 92 93 94 95
539 96 97 98 99 100 101 102 103
540 104 105 106 107 108 109 110 111
541 112 113 114 115 116 117 118 119
542 120 121 122 123 124 125 126 127
543 128 129 130 131 132 133 134 135
544 136 137 138 139 140 141 142 143
545 144 145 146 147 148 149 150 151
546 152 153 154 155 156 157 158 159
547 160 161 162 163 164 165 166 167
548 168 169 170 171 172 173 174 175
549 176 177 178 179 180 181 182 183
550 184 185 186 187 188 189 190 191
551 192 193 194 195 196 197 198 199
552 200 201 202 203 204 205 206 207
553 208 209 210 211 212 213 214 215
554 216 217 218 219 220 221 222 223
555 224 225 226 227 228 229 230 231
556 232 233 234 235 236 237 238 239
557 240 241 242 243 244 245 246 247
558 248 249 250 251 252 253 254 255
559 256>;
560 };
561
562 clocks {
563 compatible = "simple-bus";
564 #address-cells = <1>;
565 #size-cells = <0>;
566
567 clk32k_in: clock@0 {
568 compatible = "fixed-clock";
569 reg = <0>;
570 #clock-cells = <0>;
571 clock-frequency = <32768>;
572 };
573 };
574
575 cpus {
576 cpu@0 {
577 vdd-cpu-supply = <&vdd_cpu>;
578 };
579 };
580
581 gpio-keys {
582 compatible = "gpio-keys";
583
584 lid {
585 label = "Lid";
586 gpios = <&gpio TEGRA_GPIO(R, 4) GPIO_ACTIVE_LOW>;
587 linux,input-type = <5>;
588 linux,code = <KEY_RESERVED>;
589 debounce-interval = <1>;
590 wakeup-source;
591 };
592
593 power {
594 label = "Power";
595 gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
596 linux,code = <KEY_POWER>;
597 debounce-interval = <30>;
598 wakeup-source;
599 };
600 };
601
602 regulators {
603 compatible = "simple-bus";
604 #address-cells = <1>;
605 #size-cells = <0>;
606
607 vdd_mux: regulator@0 {
608 compatible = "regulator-fixed";
609 reg = <0>;
610 regulator-name = "+VDD_MUX";
611 regulator-min-microvolt = <12000000>;
612 regulator-max-microvolt = <12000000>;
613 regulator-always-on;
614 regulator-boot-on;
615 };
616
617 vdd_5v0_sys: regulator@1 {
618 compatible = "regulator-fixed";
619 reg = <1>;
620 regulator-name = "+5V_SYS";
621 regulator-min-microvolt = <5000000>;
622 regulator-max-microvolt = <5000000>;
623 regulator-always-on;
624 regulator-boot-on;
625 vin-supply = <&vdd_mux>;
626 };
627
628 vdd_3v3_sys: regulator@2 {
629 compatible = "regulator-fixed";
630 reg = <2>;
631 regulator-name = "+3.3V_SYS";
632 regulator-min-microvolt = <3300000>;
633 regulator-max-microvolt = <3300000>;
634 regulator-always-on;
635 regulator-boot-on;
636 vin-supply = <&vdd_mux>;
637 };
638
639 vdd_3v3_run: regulator@3 {
640 compatible = "regulator-fixed";
641 reg = <3>;
642 regulator-name = "+3.3V_RUN";
643 regulator-min-microvolt = <3300000>;
644 regulator-max-microvolt = <3300000>;
645 regulator-always-on;
646 regulator-boot-on;
647 gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
648 enable-active-high;
649 vin-supply = <&vdd_3v3_sys>;
650 };
651
652 vdd_3v3_hdmi: regulator@4 {
653 compatible = "regulator-fixed";
654 reg = <4>;
655 regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
656 regulator-min-microvolt = <3300000>;
657 regulator-max-microvolt = <3300000>;
658 vin-supply = <&vdd_3v3_run>;
659 };
660
661 vdd_led: regulator@5 {
662 compatible = "regulator-fixed";
663 reg = <5>;
664 regulator-name = "+VDD_LED";
665 gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
666 enable-active-high;
667 vin-supply = <&vdd_mux>;
668 };
669
670 vdd_5v0_ts: regulator@6 {
671 compatible = "regulator-fixed";
672 reg = <6>;
673 regulator-name = "+5V_VDD_TS_SW";
674 regulator-min-microvolt = <5000000>;
675 regulator-max-microvolt = <5000000>;
676 regulator-boot-on;
677 gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
678 enable-active-high;
679 vin-supply = <&vdd_5v0_sys>;
680 };
681
682 vdd_usb1_vbus: regulator@7 {
683 compatible = "regulator-fixed";
684 reg = <7>;
685 regulator-name = "+5V_USB_HS";
686 regulator-min-microvolt = <5000000>;
687 regulator-max-microvolt = <5000000>;
688 gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
689 enable-active-high;
690 gpio-open-drain;
691 vin-supply = <&vdd_5v0_sys>;
692 };
693
694 vdd_usb3_vbus: regulator@8 {
695 compatible = "regulator-fixed";
696 reg = <8>;
697 regulator-name = "+5V_USB_SS";
698 regulator-min-microvolt = <5000000>;
699 regulator-max-microvolt = <5000000>;
700 gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
701 enable-active-high;
702 gpio-open-drain;
703 vin-supply = <&vdd_5v0_sys>;
704 };
705
706 vdd_3v3_panel: regulator@9 {
707 compatible = "regulator-fixed";
708 reg = <9>;
709 regulator-name = "+3.3V_PANEL";
710 regulator-min-microvolt = <3300000>;
711 regulator-max-microvolt = <3300000>;
712 gpio = <&pmic 4 GPIO_ACTIVE_HIGH>;
713 enable-active-high;
714 vin-supply = <&vdd_3v3_run>;
715 };
716
717 vdd_3v3_lp0: regulator@10 {
718 compatible = "regulator-fixed";
719 reg = <10>;
720 regulator-name = "+3.3V_LP0";
721 regulator-min-microvolt = <3300000>;
722 regulator-max-microvolt = <3300000>;
723 /*
724 * TODO: find a way to wire this up with the USB EHCI
725 * controllers so that it can be enabled on demand.
726 */
727 regulator-always-on;
728 gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
729 enable-active-high;
730 vin-supply = <&vdd_3v3_sys>;
731 };
732
733 vdd_hdmi_pll: regulator@11 {
734 compatible = "regulator-fixed";
735 reg = <11>;
736 regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
737 regulator-min-microvolt = <1050000>;
738 regulator-max-microvolt = <1050000>;
739 gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>;
740 vin-supply = <&vdd_1v05_run>;
741 };
742
743 vdd_5v0_hdmi: regulator@12 {
744 compatible = "regulator-fixed";
745 reg = <12>;
746 regulator-name = "+5V_HDMI_CON";
747 regulator-min-microvolt = <5000000>;
748 regulator-max-microvolt = <5000000>;
749 gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
750 enable-active-high;
751 vin-supply = <&vdd_5v0_sys>;
752 };
753 };
754
755 sound {
756 nvidia,audio-routing =
757 "Headphones", "HPR",
758 "Headphones", "HPL",
759 "Speakers", "SPKR",
760 "Speakers", "SPKL",
761 "Mic Jack", "MICBIAS",
762 "DMICL", "Int Mic",
763 "DMICR", "Int Mic",
764 "IN34", "Mic Jack";
765
766 nvidia,i2s-controller = <&tegra_i2s1>;
767 nvidia,audio-codec = <&acodec>;
768
769 clocks = <&tegra_car TEGRA124_CLK_PLL_A>,
770 <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
771 <&tegra_car TEGRA124_CLK_EXTERN1>;
772 clock-names = "pll_a", "pll_a_out0", "mclk";
773
774 nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(I, 7) GPIO_ACTIVE_HIGH>;
775 nvidia,mic-det-gpios =
776 <&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>;
777 };
778
779 gpio-restart {
780 compatible = "gpio-restart";
781 gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
782 priority = <200>;
783 };
784};
785
786#include "cros-ec-keyboard.dtsi"