Loading...
1/*
2 * Copyright 2012 ST-Ericsson AB
3 *
4 * The code contained herein is licensed under the GNU General Public
5 * License. You may obtain a copy of the GNU General Public License
6 * Version 2 or later at the following locations:
7 *
8 * http://www.opensource.org/licenses/gpl-license.html
9 * http://www.gnu.org/copyleft/gpl.html
10 *
11 * Device Tree for the TVK1281618 UIB
12 */
13
14#include <dt-bindings/interrupt-controller/irq.h>
15
16/ {
17 gpio_keys {
18 compatible = "gpio-keys";
19 #address-cells = <1>;
20 #size-cells = <0>;
21 vdd-supply = <&ab8500_ldo_aux1_reg>;
22 pinctrl-names = "default";
23 pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>;
24
25 button@139 {
26 /* Proximity sensor */
27 gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>;
28 linux,code = <11>; /* SW_FRONT_PROXIMITY */
29 label = "SFH7741 Proximity Sensor";
30 };
31 button@145 {
32 /* Hall sensor */
33 gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
34 linux,code = <0>; /* SW_LID */
35 label = "HED54XXU11 Hall Effect Sensor";
36 };
37 };
38
39 soc {
40 i2c@80004000 {
41 tc35893@44 {
42 compatible = "toshiba,tc35893";
43 reg = <0x44>;
44 interrupt-parent = <&gpio6>;
45 interrupts = <26 IRQ_TYPE_EDGE_RISING>;
46 pinctrl-names = "default";
47 pinctrl-0 = <&tc35893_tvk_mode>;
48
49 interrupt-controller;
50 #interrupt-cells = <1>;
51
52 tc3589x_gpio {
53 compatible = "toshiba,tc3589x-gpio";
54 interrupts = <0>;
55
56 interrupt-controller;
57 #interrupt-cells = <2>;
58 gpio-controller;
59 #gpio-cells = <2>;
60 };
61 tc3589x_keypad {
62 compatible = "toshiba,tc3589x-keypad";
63 interrupts = <6>;
64 debounce-delay-ms = <4>;
65 keypad,num-columns = <8>;
66 keypad,num-rows = <8>;
67 linux,no-autorepeat;
68 wakeup-source;
69 linux,keymap = <0x0301006b
70 0x04010066
71 0x06040072
72 0x040200d7
73 0x0303006a
74 0x0205000e
75 0x0607008b
76 0x0500001c
77 0x0403000b
78 0x03040034
79 0x05020067
80 0x0305006c
81 0x040500e7
82 0x0005009e
83 0x06020073
84 0x01030039
85 0x07060069
86 0x050500d9>;
87 };
88 };
89 };
90 /* Sensors mounted on this board variant */
91 i2c@80128000 {
92 lsm303dlh@18 {
93 /* Accelerometer */
94 compatible = "st,lsm303dlh-accel";
95 st,drdy-int-pin = <1>;
96 drive-open-drain;
97 reg = <0x18>;
98 vdd-supply = <&ab8500_ldo_aux1_reg>;
99 vddio-supply = <&db8500_vsmps2_reg>;
100 pinctrl-names = "default";
101 pinctrl-0 = <&accel_tvk_mode>;
102 /*
103 * These interrupts cannot be used: the other component
104 * ST-Micro L3D4200D gyro that is connected to the same lines
105 * cannot set its DRDY line to open drain, so it cannot be
106 * shared with other peripherals. The should be defined for
107 * the falling edge if they could be wired together.
108 *
109 * interrupts-extended =
110 * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
111 * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
112 */
113 };
114 lsm303dlh@1e {
115 /* Magnetometer */
116 compatible = "st,lsm303dlh-magn";
117 reg = <0x1e>;
118 vdd-supply = <&ab8500_ldo_aux1_reg>;
119 vddio-supply = <&db8500_vsmps2_reg>;
120 /*
121 * These interrupts cannot be used: the other component
122 * ST-Micro L3D4200D gyro that is connected to the same lines
123 * cannot set its DRDY line to open drain, so it cannot be
124 * shared with other peripherals. The should be defined for
125 * the falling edge if they could be wired together.
126 *
127 * interrupts-extended =
128 * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
129 * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
130 */
131 };
132 lis331dl@1c {
133 /* Accelerometer */
134 compatible = "st,lis331dl-accel";
135 st,drdy-int-pin = <1>;
136 reg = <0x1c>;
137 vdd-supply = <&ab8500_ldo_aux1_reg>;
138 vddio-supply = <&db8500_vsmps2_reg>;
139 pinctrl-names = "default";
140 pinctrl-0 = <&accel_tvk_mode>;
141 interrupt-parent = <&gpio2>;
142 /* INT2 would need to be open drain */
143 interrupts = <18 IRQ_TYPE_EDGE_RISING>,
144 <19 IRQ_TYPE_EDGE_RISING>;
145 };
146 ak8974@f {
147 /* Magnetometer */
148 compatible = "asahi-kasei,ak8974";
149 reg = <0x0f>;
150 avdd-supply = <&ab8500_ldo_aux1_reg>;
151 dvdd-supply = <&db8500_vsmps2_reg>;
152 pinctrl-names = "default";
153 pinctrl-0 = <&gyro_magn_tvk_mode>;
154 /*
155 * These interrupts cannot be used: the other component
156 * ST-Micro L3D4200D gyro that is connected to the same lines
157 * cannot set its DRDY line to open drain, so it cannot be
158 * shared with other peripherals. The should be defined for
159 * the falling edge if they could be wired together.
160 *
161 * interrupts-extended =
162 * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
163 * <&gpio0 31 IRQ_TYPE_EDGE_FALLING>;
164 */
165 };
166 l3g4200d@68 {
167 /* Gyroscope */
168 compatible = "st,l3g4200d-gyro";
169 st,drdy-int-pin = <2>;
170 reg = <0x68>;
171 vdd-supply = <&ab8500_ldo_aux1_reg>;
172 vddio-supply = <&db8500_vsmps2_reg>;
173 pinctrl-names = "default";
174 pinctrl-0 = <&gyro_magn_tvk_mode>;
175 interrupts-extended =
176 <&gpio1 0 IRQ_TYPE_EDGE_RISING>,
177 <&gpio0 31 IRQ_TYPE_EDGE_RISING>;
178 };
179 lsp001wm@5c {
180 /* Barometer/pressure sensor */
181 compatible = "st,lps001wp-press";
182 reg = <0x5c>;
183 vdd-supply = <&ab8500_ldo_aux1_reg>;
184 vddio-supply = <&db8500_vsmps2_reg>;
185 };
186 };
187
188 i2c@80110000 {
189 synaptics@4b {
190 /* Synaptics RMI4 TM1217 touchscreen */
191 compatible = "syna,rmi4-i2c";
192 #address-cells = <1>;
193 #size-cells = <0>;
194 reg = <0x4b>;
195 vdd-supply = <&ab8500_ldo_aux1_reg>;
196 vddio-supply = <&db8500_vsmps2_reg>;
197 pinctrl-names = "default";
198 pinctrl-0 = <&synaptics_tvk_mode>;
199 interrupt-parent = <&gpio2>;
200 interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
201
202 rmi-f01@1 {
203 reg = <0x1>;
204 syna,nosleep = <1>;
205 };
206 rmi-f11@11 {
207 reg = <0x11>;
208 touchscreen-inverted-x;
209 syna,sensor-type = <1>;
210 };
211 };
212 };
213
214 pinctrl {
215 /* Pull up this GPIO pin */
216 tc35893 {
217 tc35893_tvk_mode: tc35893_tvk {
218 tvk_cfg {
219 pins = "GPIO218_AH11";
220 ste,config = <&gpio_in_pu>;
221 };
222 };
223 };
224 prox {
225 prox_tvk_mode: prox_tvk {
226 tvk_cfg {
227 pins = "GPIO217_AH12";
228 ste,config = <&gpio_in_pu>;
229 };
230 };
231 };
232 hall {
233 hall_tvk_mode: hall_tvk {
234 tvk_cfg {
235 pins = "GPIO145_C13";
236 ste,config = <&gpio_in_pu>;
237 };
238 };
239 };
240 accelerometer {
241 accel_tvk_mode: accel_tvk {
242 /* Accelerometer interrupt lines 1 & 2 */
243 tvk_cfg {
244 pins = "GPIO82_C1", "GPIO83_D3";
245 ste,config = <&gpio_in_pd>;
246 };
247 };
248 };
249 gyroscope {
250 /*
251 * These lines are shared between Gyroscope l3g400dh
252 * and AK8974 magnetometer.
253 */
254 gyro_magn_tvk_mode: gyro_magn_tvk {
255 /* GPIO 31 used for INT pull down the line */
256 tvk_cfg1 {
257 pins = "GPIO31_V3";
258 ste,config = <&gpio_in_pd>;
259 };
260 /* GPIO 32 used for DRDY, pull this down */
261 tvk_cfg2 {
262 pins = "GPIO32_V2";
263 ste,config = <&gpio_in_pd>;
264 };
265 };
266 };
267 synaptics {
268 synaptics_tvk_mode: synaptics_tvk {
269 /* Touchscreen uses GPIO 84 */
270 tvk_cfg1 {
271 pins = "GPIO84_C2";
272 ste,config = <&gpio_in_pu>;
273 };
274 };
275 };
276 };
277 };
278};
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * Copyright 2012 ST-Ericsson AB
4 *
5 * Device Tree for the TVK1281618 UIB
6 */
7
8#include <dt-bindings/interrupt-controller/irq.h>
9
10/ {
11 gpio_keys {
12 compatible = "gpio-keys";
13 #address-cells = <1>;
14 #size-cells = <0>;
15 vdd-supply = <&ab8500_ldo_aux1_reg>;
16 pinctrl-names = "default";
17 pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>;
18
19 button@139 {
20 /* Proximity sensor */
21 gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>;
22 linux,code = <11>; /* SW_FRONT_PROXIMITY */
23 label = "SFH7741 Proximity Sensor";
24 };
25 button@145 {
26 /* Hall sensor */
27 gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
28 linux,code = <0>; /* SW_LID */
29 label = "HED54XXU11 Hall Effect Sensor";
30 };
31 };
32
33 soc {
34 i2c@80004000 {
35 tc35893@44 {
36 compatible = "toshiba,tc35893";
37 reg = <0x44>;
38 interrupt-parent = <&gpio6>;
39 interrupts = <26 IRQ_TYPE_EDGE_RISING>;
40 pinctrl-names = "default";
41 pinctrl-0 = <&tc35893_tvk_mode>;
42
43 interrupt-controller;
44 #interrupt-cells = <1>;
45
46 tc3589x_gpio {
47 compatible = "toshiba,tc3589x-gpio";
48 interrupts = <0>;
49
50 interrupt-controller;
51 #interrupt-cells = <2>;
52 gpio-controller;
53 #gpio-cells = <2>;
54 };
55 tc3589x_keypad {
56 compatible = "toshiba,tc3589x-keypad";
57 interrupts = <6>;
58 debounce-delay-ms = <4>;
59 keypad,num-columns = <8>;
60 keypad,num-rows = <8>;
61 linux,no-autorepeat;
62 wakeup-source;
63 linux,keymap = <0x0301006b
64 0x04010066
65 0x06040072
66 0x040200d7
67 0x0303006a
68 0x0205000e
69 0x0607008b
70 0x0500001c
71 0x0403000b
72 0x03040034
73 0x05020067
74 0x0305006c
75 0x040500e7
76 0x0005009e
77 0x06020073
78 0x01030039
79 0x07060069
80 0x050500d9>;
81 };
82 };
83 };
84 /* Sensors mounted on this board variant */
85 i2c@80128000 {
86 lsm303dlh@18 {
87 /* Accelerometer */
88 compatible = "st,lsm303dlh-accel";
89 st,drdy-int-pin = <1>;
90 drive-open-drain;
91 reg = <0x18>;
92 vdd-supply = <&ab8500_ldo_aux1_reg>;
93 vddio-supply = <&db8500_vsmps2_reg>;
94 pinctrl-names = "default";
95 pinctrl-0 = <&accel_tvk_mode>;
96 /*
97 * These interrupts cannot be used: the other component
98 * ST-Micro L3D4200D gyro that is connected to the same lines
99 * cannot set its DRDY line to open drain, so it cannot be
100 * shared with other peripherals. The should be defined for
101 * the falling edge if they could be wired together.
102 *
103 * interrupts-extended =
104 * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
105 * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
106 */
107 };
108 lsm303dlh@1e {
109 /* Magnetometer */
110 compatible = "st,lsm303dlh-magn";
111 reg = <0x1e>;
112 vdd-supply = <&ab8500_ldo_aux1_reg>;
113 vddio-supply = <&db8500_vsmps2_reg>;
114 /*
115 * These interrupts cannot be used: the other component
116 * ST-Micro L3D4200D gyro that is connected to the same lines
117 * cannot set its DRDY line to open drain, so it cannot be
118 * shared with other peripherals. The should be defined for
119 * the falling edge if they could be wired together.
120 *
121 * interrupts-extended =
122 * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
123 * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
124 */
125 };
126 lis331dl@1c {
127 /* Accelerometer */
128 compatible = "st,lis331dl-accel";
129 st,drdy-int-pin = <1>;
130 reg = <0x1c>;
131 vdd-supply = <&ab8500_ldo_aux1_reg>;
132 vddio-supply = <&db8500_vsmps2_reg>;
133 pinctrl-names = "default";
134 pinctrl-0 = <&accel_tvk_mode>;
135 interrupt-parent = <&gpio2>;
136 /* INT2 would need to be open drain */
137 interrupts = <18 IRQ_TYPE_EDGE_RISING>,
138 <19 IRQ_TYPE_EDGE_RISING>;
139 };
140 ak8974@f {
141 /* Magnetometer */
142 compatible = "asahi-kasei,ak8974";
143 reg = <0x0f>;
144 avdd-supply = <&ab8500_ldo_aux1_reg>;
145 dvdd-supply = <&db8500_vsmps2_reg>;
146 pinctrl-names = "default";
147 pinctrl-0 = <&gyro_magn_tvk_mode>;
148 /*
149 * These interrupts cannot be used: the other component
150 * ST-Micro L3D4200D gyro that is connected to the same lines
151 * cannot set its DRDY line to open drain, so it cannot be
152 * shared with other peripherals. The should be defined for
153 * the falling edge if they could be wired together.
154 *
155 * interrupts-extended =
156 * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
157 * <&gpio0 31 IRQ_TYPE_EDGE_FALLING>;
158 */
159 };
160 l3g4200d@68 {
161 /* Gyroscope */
162 compatible = "st,l3g4200d-gyro";
163 st,drdy-int-pin = <2>;
164 reg = <0x68>;
165 vdd-supply = <&ab8500_ldo_aux1_reg>;
166 vddio-supply = <&db8500_vsmps2_reg>;
167 pinctrl-names = "default";
168 pinctrl-0 = <&gyro_magn_tvk_mode>;
169 interrupts-extended =
170 <&gpio1 0 IRQ_TYPE_EDGE_RISING>,
171 <&gpio0 31 IRQ_TYPE_EDGE_RISING>;
172 };
173 lsp001wm@5c {
174 /* Barometer/pressure sensor */
175 compatible = "st,lps001wp-press";
176 reg = <0x5c>;
177 vdd-supply = <&ab8500_ldo_aux1_reg>;
178 vddio-supply = <&db8500_vsmps2_reg>;
179 };
180 };
181
182 i2c@80110000 {
183 synaptics@4b {
184 /* Synaptics RMI4 TM1217 touchscreen */
185 compatible = "syna,rmi4-i2c";
186 #address-cells = <1>;
187 #size-cells = <0>;
188 reg = <0x4b>;
189 vdd-supply = <&ab8500_ldo_aux1_reg>;
190 vddio-supply = <&db8500_vsmps2_reg>;
191 pinctrl-names = "default";
192 pinctrl-0 = <&synaptics_tvk_mode>;
193 interrupt-parent = <&gpio2>;
194 interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
195
196 rmi-f01@1 {
197 reg = <0x1>;
198 syna,nosleep = <1>;
199 };
200 rmi-f11@11 {
201 reg = <0x11>;
202 touchscreen-inverted-x;
203 syna,sensor-type = <1>;
204 };
205 };
206 };
207
208 pinctrl {
209 /* Pull up this GPIO pin */
210 tc35893 {
211 tc35893_tvk_mode: tc35893_tvk {
212 tvk_cfg {
213 pins = "GPIO218_AH11";
214 ste,config = <&gpio_in_pu>;
215 };
216 };
217 };
218 prox {
219 prox_tvk_mode: prox_tvk {
220 tvk_cfg {
221 pins = "GPIO217_AH12";
222 ste,config = <&gpio_in_pu>;
223 };
224 };
225 };
226 hall {
227 hall_tvk_mode: hall_tvk {
228 tvk_cfg {
229 pins = "GPIO145_C13";
230 ste,config = <&gpio_in_pu>;
231 };
232 };
233 };
234 accelerometer {
235 accel_tvk_mode: accel_tvk {
236 /* Accelerometer interrupt lines 1 & 2 */
237 tvk_cfg {
238 pins = "GPIO82_C1", "GPIO83_D3";
239 ste,config = <&gpio_in_pd>;
240 };
241 };
242 };
243 gyroscope {
244 /*
245 * These lines are shared between Gyroscope l3g400dh
246 * and AK8974 magnetometer.
247 */
248 gyro_magn_tvk_mode: gyro_magn_tvk {
249 /* GPIO 31 used for INT pull down the line */
250 tvk_cfg1 {
251 pins = "GPIO31_V3";
252 ste,config = <&gpio_in_pd>;
253 };
254 /* GPIO 32 used for DRDY, pull this down */
255 tvk_cfg2 {
256 pins = "GPIO32_V2";
257 ste,config = <&gpio_in_pd>;
258 };
259 };
260 };
261 synaptics {
262 synaptics_tvk_mode: synaptics_tvk {
263 /* Touchscreen uses GPIO 84 */
264 tvk_cfg1 {
265 pins = "GPIO84_C2";
266 ste,config = <&gpio_in_pu>;
267 };
268 };
269 };
270 };
271
272 mcde@a0350000 {
273 status = "okay";
274
275 dsi@a0351000 {
276 panel {
277 compatible = "samsung,s6d16d0";
278 reg = <0>;
279 vdd1-supply = <&ab8500_ldo_aux1_reg>;
280 reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
281 };
282 };
283 };
284 };
285};