1// SPDX-License-Identifier: GPL-2.0+
 2/dts-v1/;
 3#include "zynq-7000.dtsi"
 
 4
 5/ {
 6	model = "Zynq ZYBO Z7 Development Board";
 7	compatible = "digilent,zynq-zybo-z7", "xlnx,zynq-7000";
 8
 9	aliases {
10		ethernet0 = &gem0;
11		serial0 = &uart1;
12	};
13
14	memory@0 {
15		device_type = "memory";
16		reg = <0x0 0x20000000>;
17	};
18
19	chosen {
20		bootargs = "";
21		stdout-path = "serial0:115200n8";
22	};
23
 
 
 
 
 
 
 
 
 
24	usb_phy0: phy0 {
25		#phy-cells = <0>;
26		compatible = "usb-nop-xceiv";
27		reset-gpios = <&gpio0 46 1>;
28	};
29};
30
31&clkc {
32	ps-clk-frequency = <33333333>;
33};
34
35&gem0 {
36	status = "okay";
37	phy-mode = "rgmii-id";
38	phy-handle = <&ethernet_phy>;
39
40	ethernet_phy: ethernet-phy@0 {
41		reg = <0>;
42		device_type = "ethernet-phy";
43	};
44};
45
46&sdhci0 {
47	status = "okay";
48};
49
50&uart1 {
51	status = "okay";
52};
53
54&usb0 {
55	status = "okay";
56	dr_mode = "host";
57	usb-phy = <&usb_phy0>;
58};

 1// SPDX-License-Identifier: GPL-2.0+
 2/dts-v1/;
 3#include "zynq-7000.dtsi"
 4#include <dt-bindings/gpio/gpio.h>
 5
 6/ {
 7	model = "Digilent Zybo Z7 board";
 8	compatible = "digilent,zynq-zybo-z7", "xlnx,zynq-7000";
 9
10	aliases {
11		ethernet0 = &gem0;
12		serial0 = &uart1;
13	};
14
15	memory@0 {
16		device_type = "memory";
17		reg = <0x0 0x40000000>;
18	};
19
20	chosen {
21		bootargs = "";
22		stdout-path = "serial0:115200n8";
23	};
24
25	gpio-leds {
26		compatible = "gpio-leds";
27
28		led-ld4 {
29			label = "zynq-zybo-z7:green:ld4";
30			gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
31		};
32	};
33
34	usb_phy0: phy0 {
35		#phy-cells = <0>;
36		compatible = "usb-nop-xceiv";
37		reset-gpios = <&gpio0 46 GPIO_ACTIVE_LOW>;
38	};
39};
40
41&clkc {
42	ps-clk-frequency = <33333333>;
43};
44
45&gem0 {
46	status = "okay";
47	phy-mode = "rgmii-id";
48	phy-handle = <&ethernet_phy>;
49
50	ethernet_phy: ethernet-phy@0 {
51		reg = <0>;
52		device_type = "ethernet-phy";
53	};
54};
55
56&sdhci0 {
57	status = "okay";
58};
59
60&uart1 {
61	status = "okay";
62};
63
64&usb0 {
65	status = "okay";
66	dr_mode = "host";
67	usb-phy = <&usb_phy0>;
68};