Loading...
1/*
2 * Copyright 2012 ST-Ericsson AB
3 *
4 * The code contained herein is licensed under the GNU General Public
5 * License. You may obtain a copy of the GNU General Public License
6 * Version 2 or later at the following locations:
7 *
8 * http://www.opensource.org/licenses/gpl-license.html
9 * http://www.gnu.org/copyleft/gpl.html
10 */
11
12#include "ste-dbx5x0.dtsi"
13#include "ste-href-ab8500.dtsi"
14#include "ste-href.dtsi"
15
16/ {
17 model = "ST-Ericsson HREF (v60+) platform with Device Tree";
18 compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
19
20 soc {
21 /* Name the GPIO muxed rails on the HREF boards */
22 gpio@8012e000 {
23 /* GPIOs 0 - 31 */
24 gpio-line-names =
25 /* GPIO0,1 used for UART0 BT RX/TX */
26 "", "",
27 "UART_WAKE",
28 "BT_WAKE",
29 "",
30 "SDMMC_1V8_3V_SEL",
31 "FLASH_LED_SYNC (FLASH_CTRL_0)",
32 "XENON_READY (FLASH_CTRL_1)",
33 "", "", "", "", "", "", "", "",
34 "", "", "", "",
35 "",
36 "FLASH_LED_EN (FLASH_CTRL_3)",
37 "", "",
38 "", "", "", "", "",
39 /* Used by UART2 (console) */
40 "", "",
41 "MAGNETOMETER_INT";
42 };
43
44 gpio@8012e080 {
45 /* GPIOs 32 - 63 */
46 gpio-line-names =
47 "MAGNETOMETER_DRDY",
48 "", "", "", "", "", "", "",
49 "", "", "", "", "", "", "", "",
50 "", "", "", "", "", "", "", "",
51 "", "", "", "", "", "", "", "";
52 };
53
54 gpio@8000e000 {
55 /* GPIOs 64 - 95 */
56 gpio-line-names = "XENON_EN2 (FLASH_CTRL_4)",
57 "DISP1_RST",
58 "DISP2_RST",
59 "TOUCH_INT2",
60 "LCD_VSI0_A",
61 "LCD_VSI1_A",
62 /* GPIO 70-77 used for ETM */
63 "", "", "", "", "", "", "", "",
64 /* GPIO 78-81 used for YCBCR */
65 "", "", "", "",
66 "ACCELEROMETER_INT1_RDY",
67 "ACCELEROMETER_INT2",
68 "TOUCH_INT",
69 "WLAN_ENA",
70 "", "", "", "", "",
71 "FORCE_SENSING_INT",
72 "FORCE_SENSING_RESET",
73 "", "",
74 "SDMMC_CD";
75 };
76
77 gpio@8000e080 {
78 /* GPIOs 96 - 127 */
79 gpio-line-names = "",
80 "FORCE_SENSING_WU",
81 "", "", "", "", "", "",
82 "", "", "", "", "", "", "", "",
83 "", "", "", "", "", "", "", "",
84 "", "", "", "", "", "", "", "";
85 };
86
87 gpio@8000e100 {
88 /* GPIOs 128 - 159 */
89 gpio-line-names = "", "", "", "", "", "", "", "",
90 "", "", "",
91 "DIPRO_INT", /* GPIO139 */
92 "XSHUTDOWN_SECONDARY_SENSOR",
93 "XSHUTDOWN_PRIMARY_SENSOR",
94 "NFC_RST (NFC_CTRL_",
95 "TOUCH_RST",
96 "NFC_IRQ (NFC_CTRL_1)",
97 "HAL_SW",
98 "TOUCH_RST2",
99 "", "",
100 "VAUDIO_HF_EN", /* GPIO149 */
101 "", "", "", "", "", "", "", "", "", "";
102 };
103
104 gpio@8000e180 {
105 /* GPIOs 160 - 191 */
106 gpio-line-names = "", "", "", "", "", "", "", "",
107 "",
108 "SDMMC_EN",
109 "XENON_CHARGE (FLASH_CONTROL_5)",
110 "GBF_ENA_RESET",
111 "", "", "", "",
112 "", "", "", "", "", "", "", "",
113 "", "", "", "", "", "", "", "";
114 };
115
116 gpio@8011e000 {
117 /* GPIOs 192 - 223 */
118 gpio-line-names = "HDTV_INTN",
119 "", "", "",
120 "HDTV_RSTN",
121 "", "", "",
122 "", /* GPIO200 */
123 "", "", "", "", "", "", "",
124 /* GPIO208-216 used for WGBF_MC1 */
125 "", "", "", "", "", "", "", "", "",
126 "SW_FRONT_PROXIMITY", /* GPIO217 */
127 "KPD_CTRL_INT", /* Keypad controller */
128 "", "", "", "", "";
129 };
130
131 gpio@8011e080 {
132 /* GPIOs 224 - 255 */
133 gpio-line-names = "", "",
134 "HSIT_ACWAKE0",
135 "", "", "", "", "",
136 "", "", "", "", "", "", "", "",
137 "", "", "", "", "", "", "", "",
138 "", "", "", "", "", "", "", "";
139 };
140
141 // External Micro SD slot
142 sdi0_per1@80126000 {
143 cd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; // 95
144 };
145
146 vmmci: regulator-gpio {
147 gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
148 enable-gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>;
149 enable-active-high;
150 };
151
152 pinctrl {
153 /*
154 * Set this up using hogs, as time goes by and as seems fit, these
155 * can be moved over to being controlled by respective device.
156 */
157 pinctrl-names = "default";
158 pinctrl-0 = <&ipgpio_hrefv60_mode>,
159 <&etm_hrefv60_mode>,
160 <&nahj_hrefv60_mode>,
161 <&nfc_hrefv60_mode>,
162 <&force_hrefv60_mode>,
163 <&dipro_hrefv60_mode>,
164 <&vaudio_hf_hrefv60_mode>,
165 <&gbf_hrefv60_mode>,
166 <&hdtv_hrefv60_mode>,
167 <&gpios_hrefv60_mode>;
168
169 sdi0 {
170 sdi0_default_mode: sdi0_default {
171 /* SD card detect GPIO pin, extend default state */
172 default_hrefv60_cfg1 {
173 pins = "GPIO95_E8";
174 ste,config = <&gpio_in_pu>;
175 };
176 /* VMMCI level-shifter enable */
177 default_hrefv60_cfg2 {
178 pins = "GPIO169_D22";
179 ste,config = <&gpio_out_hi>;
180 };
181 /* VMMCI level-shifter voltage select */
182 default_hrefv60_cfg3 {
183 pins = "GPIO5_AG6";
184 ste,config = <&gpio_out_hi>;
185 };
186 };
187 };
188 ipgpio {
189 /*
190 * XENON Flashgun on image processor GPIO (controlled from image
191 * processor firmware), mux in these image processor GPIO lines 0
192 * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant
193 * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias
194 * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output.
195 */
196 ipgpio_hrefv60_mode: ipgpio_hrefv60 {
197 hrefv60_mux {
198 function = "ipgpio";
199 groups = "ipgpio0_c_1", "ipgpio1_c_1", "ipgpio4_c_1";
200 };
201 hrefv60_cfg1 {
202 pins = "GPIO6_AF6", "GPIO7_AG5";
203 ste,config = <&in_pu>;
204 };
205 hrefv60_cfg2 {
206 pins = "GPIO21_AB3";
207 ste,config = <&gpio_out_lo>;
208 };
209 hrefv60_cfg3 {
210 pins = "GPIO64_F3";
211 ste,config = <&out_lo>;
212 };
213 };
214 };
215 etm {
216 /*
217 * Drive D19-D23 for the ETM PTM trace interface low,
218 * (presumably pins are unconnected therefore grounded here,
219 * the "other alt C1" setting enables these pins)
220 */
221 etm_hrefv60_mode: etm_hrefv60 {
222 hrefv60_cfg1 {
223 pins =
224 "GPIO70_G5",
225 "GPIO71_G4",
226 "GPIO72_H4",
227 "GPIO73_H3",
228 "GPIO74_J3";
229 ste,config = <&gpio_out_lo>;
230 };
231 };
232 };
233 nahj {
234 nahj_hrefv60_mode: nahj_hrefv60 {
235 /* NAHJ CTRL on GPIO76 to low, CTRL_INV on GPIO216 to high */
236 hrefv60_cfg1 {
237 pins = "GPIO76_J2";
238 ste,config = <&gpio_out_lo>;
239 };
240 hrefv60_cfg2 {
241 pins = "GPIO216_AG12";
242 ste,config = <&gpio_out_hi>;
243 };
244 };
245 };
246 nfc {
247 nfc_hrefv60_mode: nfc_hrefv60 {
248 /* NFC ENA and RESET to low, pulldown IRQ line */
249 hrefv60_cfg1 {
250 pins =
251 "GPIO77_H1", /* NFC_ENA */
252 "GPIO142_C11"; /* NFC_RESET */
253 ste,config = <&gpio_out_lo>;
254 };
255 hrefv60_cfg2 {
256 pins = "GPIO144_B13"; /* NFC_IRQ */
257 ste,config = <&gpio_in_pd>;
258 };
259 };
260 };
261 force {
262 force_hrefv60_mode: force_hrefv60 {
263 hrefv60_cfg1 {
264 pins = "GPIO91_B6"; /* FORCE_SENSING_INT */
265 ste,config = <&gpio_in_pu>;
266 };
267 hrefv60_cfg2 {
268 pins =
269 "GPIO92_D6", /* FORCE_SENSING_RST */
270 "GPIO97_D9"; /* FORCE_SENSING_WU */
271 ste,config = <&gpio_out_lo>;
272 };
273 };
274 };
275 dipro {
276 dipro_hrefv60_mode: dipro_hrefv60 {
277 hrefv60_cfg1 {
278 pins = "GPIO139_C9"; /* DIPRO_INT */
279 ste,config = <&gpio_in_pu>;
280 };
281 };
282 };
283 vaudio_hf {
284 vaudio_hf_hrefv60_mode: vaudio_hf_hrefv60 {
285 /* Audio Amplifier HF enable GPIO */
286 hrefv60_cfg1 {
287 pins = "GPIO149_B14"; /* VAUDIO_HF_EN, enable MAX8968 */
288 ste,config = <&gpio_out_hi>;
289 };
290 };
291 };
292 gbf {
293 gbf_hrefv60_mode: gbf_hrefv60 {
294 /*
295 * GBF (GPS, Bluetooth, FM-radio) interface,
296 * pull low to reset state
297 */
298 hrefv60_cfg1 {
299 pins = "GPIO171_D23"; /* GBF_ENA_RESET */
300 ste,config = <&gpio_out_lo>;
301 };
302 };
303 };
304 hdtv {
305 hdtv_hrefv60_mode: hdtv_hrefv60 {
306 /* MSP : HDTV INTERFACE GPIO line */
307 hrefv60_cfg1 {
308 pins = "GPIO192_AJ27";
309 ste,config = <&gpio_in_pd>;
310 };
311 };
312 };
313 mcde {
314 lcd_hrefv60_mode: lcd_hrefv60 {
315 /*
316 * Display Interface 1 uses GPIO 65 for RST (reset).
317 * Display Interface 2 uses GPIO 66 for RST (reset).
318 * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset)
319 */
320 hrefv60_cfg1 {
321 pins ="GPIO65_F1";
322 ste,config = <&gpio_out_hi>;
323 };
324 hrefv60_cfg2 {
325 pins ="GPIO66_G3";
326 ste,config = <&gpio_out_lo>;
327 };
328 };
329 };
330 gpios {
331 /* Dangling GPIO pins */
332 gpios_hrefv60_mode: gpios_hrefv60 {
333 default_cfg1 {
334 /* Normally UART1 RXD, now dangling */
335 pins = "GPIO4_AH6";
336 ste,config = <&in_pu>;
337 };
338 };
339 };
340 };
341 };
342};
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * Copyright 2012 ST-Ericsson AB
4 */
5
6#include "ste-href-ab8500.dtsi"
7#include "ste-href.dtsi"
8
9/ {
10 model = "ST-Ericsson HREF (v60+) platform with Device Tree";
11 compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
12
13 thermal-zones {
14 chassis-thermal {
15 /* Poll every 20 seconds */
16 polling-delay = <20000>;
17 /* Poll every 2nd second when cooling */
18 polling-delay-passive = <2000>;
19
20 thermal-sensors = <&therm1>, <&therm2>;
21
22 /* Tripping points made from rough guess about operating conditions */
23 trips {
24 chassis_alert: chassis-alert {
25 /* At 50 degrees take down the CPU frequency */
26 temperature = <50000>;
27 hysteresis = <3000>;
28 type = "active";
29 };
30 chassis_crit: chassis-crit {
31 /* Just shut down at 70 degrees */
32 temperature = <70000>;
33 hysteresis = <2000>;
34 type = "critical";
35 };
36 };
37
38 /* Push down the operating frequency of the SoC when it gets hot */
39 cooling-maps {
40 map0 {
41 trip = <&chassis_alert>;
42 cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
43 contribution = <100>;
44 };
45 };
46 };
47 };
48
49 /*
50 * Thermistors on the board, formally to monitor battery temperatures
51 * but what they measure is the board temperature.
52 */
53 therm1: thermistor@0 {
54 compatible = "murata,ncp18wb473";
55 io-channels = <&gpadc 0x06>; /* AUX1 */
56 pullup-uv = <1800000>;
57 pullup-ohm = <220000>;
58 pulldown-ohm = <0>;
59 #thermal-sensor-cells = <0>;
60 };
61
62 therm2: thermistor@1 {
63 compatible = "murata,ncp18wb473";
64 io-channels = <&gpadc 0x07>; /* AUX2 */
65 pullup-uv = <1800000>;
66 pullup-ohm = <220000>;
67 pulldown-ohm = <0>;
68 #thermal-sensor-cells = <0>;
69 };
70
71 soc {
72 /* Name the GPIO muxed rails on the HREF boards */
73 gpio@8012e000 {
74 /* GPIOs 0 - 31 */
75 gpio-line-names =
76 /* GPIO0,1 used for UART0 BT RX/TX */
77 "", "",
78 "UART_WAKE",
79 "BT_WAKE",
80 "",
81 "SDMMC_1V8_3V_SEL",
82 "FLASH_LED_SYNC (FLASH_CTRL_0)",
83 "XENON_READY (FLASH_CTRL_1)",
84 "", "", "", "", "", "", "", "",
85 "", "", "", "",
86 "",
87 "FLASH_LED_EN (FLASH_CTRL_3)",
88 "", "",
89 "", "", "", "", "",
90 /* Used by UART2 (console) */
91 "", "",
92 "MAGNETOMETER_INT";
93 };
94
95 gpio@8012e080 {
96 /* GPIOs 32 - 63 */
97 gpio-line-names =
98 "MAGNETOMETER_DRDY",
99 "", "", "", "", "", "", "",
100 "", "", "", "", "", "", "", "",
101 "", "", "", "", "", "", "", "",
102 "", "", "", "", "", "", "", "";
103 };
104
105 gpio@8000e000 {
106 /* GPIOs 64 - 95 */
107 gpio-line-names = "XENON_EN2 (FLASH_CTRL_4)",
108 "DISP1_RST",
109 "DISP2_RST",
110 "TOUCH_INT2",
111 "LCD_VSI0_A",
112 "LCD_VSI1_A",
113 /* GPIO 70-77 used for ETM */
114 "", "", "", "", "", "", "", "",
115 /* GPIO 78-81 used for YCBCR */
116 "", "", "", "",
117 "ACCELEROMETER_INT1_RDY",
118 "ACCELEROMETER_INT2",
119 "TOUCH_INT",
120 "WLAN_ENA",
121 "", "", "", "", "",
122 "FORCE_SENSING_INT",
123 "FORCE_SENSING_RESET",
124 "", "",
125 "SDMMC_CD";
126 };
127
128 gpio@8000e080 {
129 /* GPIOs 96 - 127 */
130 gpio-line-names = "",
131 "FORCE_SENSING_WU",
132 "", "", "", "", "", "",
133 "", "", "", "", "", "", "", "",
134 "", "", "", "", "", "", "", "",
135 "", "", "", "", "", "", "", "";
136 };
137
138 gpio@8000e100 {
139 /* GPIOs 128 - 159 */
140 gpio-line-names = "", "", "", "", "", "", "", "",
141 "", "", "",
142 "DIPRO_INT", /* GPIO139 */
143 "XSHUTDOWN_SECONDARY_SENSOR",
144 "XSHUTDOWN_PRIMARY_SENSOR",
145 "NFC_RST (NFC_CTRL_",
146 "TOUCH_RST",
147 "NFC_IRQ (NFC_CTRL_1)",
148 "HAL_SW",
149 "TOUCH_RST2",
150 "", "",
151 "VAUDIO_HF_EN", /* GPIO149 */
152 "", "", "", "", "", "", "", "", "", "";
153 };
154
155 gpio@8000e180 {
156 /* GPIOs 160 - 191 */
157 gpio-line-names = "", "", "", "", "", "", "", "",
158 "",
159 "SDMMC_EN",
160 "XENON_CHARGE (FLASH_CONTROL_5)",
161 "GBF_ENA_RESET",
162 "", "", "", "",
163 "", "", "", "", "", "", "", "",
164 "", "", "", "", "", "", "", "";
165 };
166
167 gpio@8011e000 {
168 /* GPIOs 192 - 223 */
169 gpio-line-names = "HDTV_INTN",
170 "", "", "",
171 "HDTV_RSTN",
172 "", "", "",
173 "", /* GPIO200 */
174 "", "", "", "", "", "", "",
175 /* GPIO208-216 used for WGBF_MC1 */
176 "", "", "", "", "", "", "", "", "",
177 "SW_FRONT_PROXIMITY", /* GPIO217 */
178 "KPD_CTRL_INT", /* Keypad controller */
179 "", "", "", "", "";
180 };
181
182 gpio@8011e080 {
183 /* GPIOs 224 - 255 */
184 gpio-line-names = "", "",
185 "HSIT_ACWAKE0",
186 "", "", "", "", "",
187 "", "", "", "", "", "", "", "",
188 "", "", "", "", "", "", "", "",
189 "", "", "", "", "", "", "", "";
190 };
191
192 // External Micro SD slot
193 mmc@80126000 {
194 cd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; // 95
195 };
196
197 pinctrl {
198 /*
199 * Set this up using hogs, as time goes by and as seems fit, these
200 * can be moved over to being controlled by respective device.
201 */
202 pinctrl-names = "default";
203 pinctrl-0 = <&ipgpio_hrefv60_mode>,
204 <&etm_hrefv60_mode>,
205 <&nahj_hrefv60_mode>,
206 <&nfc_hrefv60_mode>,
207 <&force_hrefv60_mode>,
208 <&dipro_hrefv60_mode>,
209 <&vaudio_hf_hrefv60_mode>,
210 <&gbf_hrefv60_mode>,
211 <&hdtv_hrefv60_mode>,
212 <&gpios_hrefv60_mode>;
213
214 sdi0 {
215 sdi0_default_mode: sdi0_default {
216 /* SD card detect GPIO pin, extend default state */
217 default_hrefv60_cfg1 {
218 pins = "GPIO95_E8";
219 ste,config = <&gpio_in_pu>;
220 };
221 };
222 };
223 ipgpio {
224 /*
225 * XENON Flashgun on image processor GPIO (controlled from image
226 * processor firmware), mux in these image processor GPIO lines 0
227 * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant
228 * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias
229 * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output.
230 */
231 ipgpio_hrefv60_mode: ipgpio_hrefv60 {
232 hrefv60_mux {
233 function = "ipgpio";
234 groups = "ipgpio0_c_1", "ipgpio1_c_1", "ipgpio4_c_1";
235 };
236 hrefv60_cfg1 {
237 pins = "GPIO6_AF6", "GPIO7_AG5";
238 ste,config = <&in_pu>;
239 };
240 hrefv60_cfg2 {
241 pins = "GPIO21_AB3";
242 ste,config = <&gpio_out_lo>;
243 };
244 hrefv60_cfg3 {
245 pins = "GPIO64_F3";
246 ste,config = <&out_lo>;
247 };
248 };
249 };
250 etm {
251 /*
252 * Drive D19-D23 for the ETM PTM trace interface low,
253 * (presumably pins are unconnected therefore grounded here,
254 * the "other alt C1" setting enables these pins)
255 */
256 etm_hrefv60_mode: etm_hrefv60 {
257 hrefv60_cfg1 {
258 pins =
259 "GPIO70_G5",
260 "GPIO71_G4",
261 "GPIO72_H4",
262 "GPIO73_H3",
263 "GPIO74_J3";
264 ste,config = <&gpio_out_lo>;
265 };
266 };
267 };
268 nahj {
269 nahj_hrefv60_mode: nahj_hrefv60 {
270 /* NAHJ CTRL on GPIO76 to low, CTRL_INV on GPIO216 to high */
271 hrefv60_cfg1 {
272 pins = "GPIO76_J2";
273 ste,config = <&gpio_out_lo>;
274 };
275 hrefv60_cfg2 {
276 pins = "GPIO216_AG12";
277 ste,config = <&gpio_out_hi>;
278 };
279 };
280 };
281 nfc {
282 nfc_hrefv60_mode: nfc_hrefv60 {
283 /* NFC ENA and RESET to low, pulldown IRQ line */
284 hrefv60_cfg1 {
285 pins =
286 "GPIO77_H1", /* NFC_ENA */
287 "GPIO142_C11"; /* NFC_RESET */
288 ste,config = <&gpio_out_lo>;
289 };
290 hrefv60_cfg2 {
291 pins = "GPIO144_B13"; /* NFC_IRQ */
292 ste,config = <&gpio_in_pd>;
293 };
294 };
295 };
296 force {
297 force_hrefv60_mode: force_hrefv60 {
298 hrefv60_cfg1 {
299 pins = "GPIO91_B6"; /* FORCE_SENSING_INT */
300 ste,config = <&gpio_in_pu>;
301 };
302 hrefv60_cfg2 {
303 pins =
304 "GPIO92_D6", /* FORCE_SENSING_RST */
305 "GPIO97_D9"; /* FORCE_SENSING_WU */
306 ste,config = <&gpio_out_lo>;
307 };
308 };
309 };
310 dipro {
311 dipro_hrefv60_mode: dipro_hrefv60 {
312 hrefv60_cfg1 {
313 pins = "GPIO139_C9"; /* DIPRO_INT */
314 ste,config = <&gpio_in_pu>;
315 };
316 };
317 };
318 vaudio_hf {
319 vaudio_hf_hrefv60_mode: vaudio_hf_hrefv60 {
320 /* Audio Amplifier HF enable GPIO */
321 hrefv60_cfg1 {
322 pins = "GPIO149_B14"; /* VAUDIO_HF_EN, enable MAX8968 */
323 ste,config = <&gpio_out_hi>;
324 };
325 };
326 };
327 gbf {
328 gbf_hrefv60_mode: gbf_hrefv60 {
329 /*
330 * GBF (GPS, Bluetooth, FM-radio) interface,
331 * pull low to reset state
332 */
333 hrefv60_cfg1 {
334 pins = "GPIO171_D23"; /* GBF_ENA_RESET */
335 ste,config = <&gpio_out_lo>;
336 };
337 };
338 };
339 hdtv {
340 hdtv_hrefv60_mode: hdtv_hrefv60 {
341 /* MSP : HDTV INTERFACE GPIO line */
342 hrefv60_cfg1 {
343 pins = "GPIO192_AJ27";
344 ste,config = <&gpio_in_pd>;
345 };
346 };
347 };
348 mcde {
349 lcd_hrefv60_mode: lcd_hrefv60 {
350 /*
351 * Display Interface 1 uses GPIO 65 for RST (reset).
352 * Display Interface 2 uses GPIO 66 for RST (reset).
353 * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset)
354 */
355 hrefv60_cfg1 {
356 pins ="GPIO65_F1";
357 ste,config = <&gpio_out_hi>;
358 };
359 hrefv60_cfg2 {
360 pins ="GPIO66_G3";
361 ste,config = <&gpio_out_lo>;
362 };
363 };
364 };
365 gpios {
366 /* Dangling GPIO pins */
367 gpios_hrefv60_mode: gpios_hrefv60 {
368 default_cfg1 {
369 /* Normally UART1 RXD, now dangling */
370 pins = "GPIO4_AH6";
371 ste,config = <&in_pu>;
372 };
373 };
374 };
375 };
376 };
377};