Loading...
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * MDIO bus driver for the Xilinx Axi Ethernet device
4 *
5 * Copyright (c) 2009 Secret Lab Technologies, Ltd.
6 * Copyright (c) 2010 - 2011 Michal Simek <monstr@monstr.eu>
7 * Copyright (c) 2010 - 2011 PetaLogix
8 * Copyright (c) 2010 - 2012 Xilinx, Inc. All rights reserved.
9 */
10
11#include <linux/of_address.h>
12#include <linux/of_mdio.h>
13#include <linux/jiffies.h>
14
15#include "xilinx_axienet.h"
16
17#define MAX_MDIO_FREQ 2500000 /* 2.5 MHz */
18#define DEFAULT_CLOCK_DIVISOR XAE_MDIO_DIV_DFT
19
20/* Wait till MDIO interface is ready to accept a new transaction.*/
21int axienet_mdio_wait_until_ready(struct axienet_local *lp)
22{
23 unsigned long end = jiffies + 2;
24 while (!(axienet_ior(lp, XAE_MDIO_MCR_OFFSET) &
25 XAE_MDIO_MCR_READY_MASK)) {
26 if (time_before_eq(end, jiffies)) {
27 WARN_ON(1);
28 return -ETIMEDOUT;
29 }
30 udelay(1);
31 }
32 return 0;
33}
34
35/**
36 * axienet_mdio_read - MDIO interface read function
37 * @bus: Pointer to mii bus structure
38 * @phy_id: Address of the PHY device
39 * @reg: PHY register to read
40 *
41 * Return: The register contents on success, -ETIMEDOUT on a timeout
42 *
43 * Reads the contents of the requested register from the requested PHY
44 * address by first writing the details into MCR register. After a while
45 * the register MRD is read to obtain the PHY register content.
46 */
47static int axienet_mdio_read(struct mii_bus *bus, int phy_id, int reg)
48{
49 u32 rc;
50 int ret;
51 struct axienet_local *lp = bus->priv;
52
53 ret = axienet_mdio_wait_until_ready(lp);
54 if (ret < 0)
55 return ret;
56
57 axienet_iow(lp, XAE_MDIO_MCR_OFFSET,
58 (((phy_id << XAE_MDIO_MCR_PHYAD_SHIFT) &
59 XAE_MDIO_MCR_PHYAD_MASK) |
60 ((reg << XAE_MDIO_MCR_REGAD_SHIFT) &
61 XAE_MDIO_MCR_REGAD_MASK) |
62 XAE_MDIO_MCR_INITIATE_MASK |
63 XAE_MDIO_MCR_OP_READ_MASK));
64
65 ret = axienet_mdio_wait_until_ready(lp);
66 if (ret < 0)
67 return ret;
68
69 rc = axienet_ior(lp, XAE_MDIO_MRD_OFFSET) & 0x0000FFFF;
70
71 dev_dbg(lp->dev, "axienet_mdio_read(phy_id=%i, reg=%x) == %x\n",
72 phy_id, reg, rc);
73
74 return rc;
75}
76
77/**
78 * axienet_mdio_write - MDIO interface write function
79 * @bus: Pointer to mii bus structure
80 * @phy_id: Address of the PHY device
81 * @reg: PHY register to write to
82 * @val: Value to be written into the register
83 *
84 * Return: 0 on success, -ETIMEDOUT on a timeout
85 *
86 * Writes the value to the requested register by first writing the value
87 * into MWD register. The the MCR register is then appropriately setup
88 * to finish the write operation.
89 */
90static int axienet_mdio_write(struct mii_bus *bus, int phy_id, int reg,
91 u16 val)
92{
93 int ret;
94 struct axienet_local *lp = bus->priv;
95
96 dev_dbg(lp->dev, "axienet_mdio_write(phy_id=%i, reg=%x, val=%x)\n",
97 phy_id, reg, val);
98
99 ret = axienet_mdio_wait_until_ready(lp);
100 if (ret < 0)
101 return ret;
102
103 axienet_iow(lp, XAE_MDIO_MWD_OFFSET, (u32) val);
104 axienet_iow(lp, XAE_MDIO_MCR_OFFSET,
105 (((phy_id << XAE_MDIO_MCR_PHYAD_SHIFT) &
106 XAE_MDIO_MCR_PHYAD_MASK) |
107 ((reg << XAE_MDIO_MCR_REGAD_SHIFT) &
108 XAE_MDIO_MCR_REGAD_MASK) |
109 XAE_MDIO_MCR_INITIATE_MASK |
110 XAE_MDIO_MCR_OP_WRITE_MASK));
111
112 ret = axienet_mdio_wait_until_ready(lp);
113 if (ret < 0)
114 return ret;
115 return 0;
116}
117
118/**
119 * axienet_mdio_setup - MDIO setup function
120 * @lp: Pointer to axienet local data structure.
121 * @np: Pointer to device node
122 *
123 * Return: 0 on success, -ETIMEDOUT on a timeout, -ENOMEM when
124 * mdiobus_alloc (to allocate memory for mii bus structure) fails.
125 *
126 * Sets up the MDIO interface by initializing the MDIO clock and enabling the
127 * MDIO interface in hardware. Register the MDIO interface.
128 **/
129int axienet_mdio_setup(struct axienet_local *lp, struct device_node *np)
130{
131 int ret;
132 u32 clk_div, host_clock;
133 struct mii_bus *bus;
134 struct resource res;
135 struct device_node *np1;
136
137 /* clk_div can be calculated by deriving it from the equation:
138 * fMDIO = fHOST / ((1 + clk_div) * 2)
139 *
140 * Where fMDIO <= 2500000, so we get:
141 * fHOST / ((1 + clk_div) * 2) <= 2500000
142 *
143 * Then we get:
144 * 1 / ((1 + clk_div) * 2) <= (2500000 / fHOST)
145 *
146 * Then we get:
147 * 1 / (1 + clk_div) <= ((2500000 * 2) / fHOST)
148 *
149 * Then we get:
150 * 1 / (1 + clk_div) <= (5000000 / fHOST)
151 *
152 * So:
153 * (1 + clk_div) >= (fHOST / 5000000)
154 *
155 * And finally:
156 * clk_div >= (fHOST / 5000000) - 1
157 *
158 * fHOST can be read from the flattened device tree as property
159 * "clock-frequency" from the CPU
160 */
161
162 np1 = of_find_node_by_name(NULL, "cpu");
163 if (!np1) {
164 netdev_warn(lp->ndev, "Could not find CPU device node.\n");
165 netdev_warn(lp->ndev,
166 "Setting MDIO clock divisor to default %d\n",
167 DEFAULT_CLOCK_DIVISOR);
168 clk_div = DEFAULT_CLOCK_DIVISOR;
169 goto issue;
170 }
171 if (of_property_read_u32(np1, "clock-frequency", &host_clock)) {
172 netdev_warn(lp->ndev, "clock-frequency property not found.\n");
173 netdev_warn(lp->ndev,
174 "Setting MDIO clock divisor to default %d\n",
175 DEFAULT_CLOCK_DIVISOR);
176 clk_div = DEFAULT_CLOCK_DIVISOR;
177 of_node_put(np1);
178 goto issue;
179 }
180
181 clk_div = (host_clock / (MAX_MDIO_FREQ * 2)) - 1;
182 /* If there is any remainder from the division of
183 * fHOST / (MAX_MDIO_FREQ * 2), then we need to add
184 * 1 to the clock divisor or we will surely be above 2.5 MHz
185 */
186 if (host_clock % (MAX_MDIO_FREQ * 2))
187 clk_div++;
188
189 netdev_dbg(lp->ndev,
190 "Setting MDIO clock divisor to %u/%u Hz host clock.\n",
191 clk_div, host_clock);
192
193 of_node_put(np1);
194issue:
195 axienet_iow(lp, XAE_MDIO_MC_OFFSET,
196 (((u32) clk_div) | XAE_MDIO_MC_MDIOEN_MASK));
197
198 ret = axienet_mdio_wait_until_ready(lp);
199 if (ret < 0)
200 return ret;
201
202 bus = mdiobus_alloc();
203 if (!bus)
204 return -ENOMEM;
205
206 np1 = of_get_parent(lp->phy_node);
207 of_address_to_resource(np1, 0, &res);
208 snprintf(bus->id, MII_BUS_ID_SIZE, "%.8llx",
209 (unsigned long long) res.start);
210
211 bus->priv = lp;
212 bus->name = "Xilinx Axi Ethernet MDIO";
213 bus->read = axienet_mdio_read;
214 bus->write = axienet_mdio_write;
215 bus->parent = lp->dev;
216 lp->mii_bus = bus;
217
218 ret = of_mdiobus_register(bus, np1);
219 if (ret) {
220 mdiobus_free(bus);
221 return ret;
222 }
223 return 0;
224}
225
226/**
227 * axienet_mdio_teardown - MDIO remove function
228 * @lp: Pointer to axienet local data structure.
229 *
230 * Unregisters the MDIO and frees any associate memory for mii bus.
231 */
232void axienet_mdio_teardown(struct axienet_local *lp)
233{
234 mdiobus_unregister(lp->mii_bus);
235 mdiobus_free(lp->mii_bus);
236 lp->mii_bus = NULL;
237}
1/*
2 * MDIO bus driver for the Xilinx Axi Ethernet device
3 *
4 * Copyright (c) 2009 Secret Lab Technologies, Ltd.
5 * Copyright (c) 2010 - 2011 Michal Simek <monstr@monstr.eu>
6 * Copyright (c) 2010 - 2011 PetaLogix
7 * Copyright (c) 2010 - 2012 Xilinx, Inc. All rights reserved.
8 */
9
10#include <linux/of_address.h>
11#include <linux/of_mdio.h>
12#include <linux/jiffies.h>
13
14#include "xilinx_axienet.h"
15
16#define MAX_MDIO_FREQ 2500000 /* 2.5 MHz */
17#define DEFAULT_CLOCK_DIVISOR XAE_MDIO_DIV_DFT
18
19/* Wait till MDIO interface is ready to accept a new transaction.*/
20int axienet_mdio_wait_until_ready(struct axienet_local *lp)
21{
22 unsigned long end = jiffies + 2;
23 while (!(axienet_ior(lp, XAE_MDIO_MCR_OFFSET) &
24 XAE_MDIO_MCR_READY_MASK)) {
25 if (time_before_eq(end, jiffies)) {
26 WARN_ON(1);
27 return -ETIMEDOUT;
28 }
29 udelay(1);
30 }
31 return 0;
32}
33
34/**
35 * axienet_mdio_read - MDIO interface read function
36 * @bus: Pointer to mii bus structure
37 * @phy_id: Address of the PHY device
38 * @reg: PHY register to read
39 *
40 * Return: The register contents on success, -ETIMEDOUT on a timeout
41 *
42 * Reads the contents of the requested register from the requested PHY
43 * address by first writing the details into MCR register. After a while
44 * the register MRD is read to obtain the PHY register content.
45 */
46static int axienet_mdio_read(struct mii_bus *bus, int phy_id, int reg)
47{
48 u32 rc;
49 int ret;
50 struct axienet_local *lp = bus->priv;
51
52 ret = axienet_mdio_wait_until_ready(lp);
53 if (ret < 0)
54 return ret;
55
56 axienet_iow(lp, XAE_MDIO_MCR_OFFSET,
57 (((phy_id << XAE_MDIO_MCR_PHYAD_SHIFT) &
58 XAE_MDIO_MCR_PHYAD_MASK) |
59 ((reg << XAE_MDIO_MCR_REGAD_SHIFT) &
60 XAE_MDIO_MCR_REGAD_MASK) |
61 XAE_MDIO_MCR_INITIATE_MASK |
62 XAE_MDIO_MCR_OP_READ_MASK));
63
64 ret = axienet_mdio_wait_until_ready(lp);
65 if (ret < 0)
66 return ret;
67
68 rc = axienet_ior(lp, XAE_MDIO_MRD_OFFSET) & 0x0000FFFF;
69
70 dev_dbg(lp->dev, "axienet_mdio_read(phy_id=%i, reg=%x) == %x\n",
71 phy_id, reg, rc);
72
73 return rc;
74}
75
76/**
77 * axienet_mdio_write - MDIO interface write function
78 * @bus: Pointer to mii bus structure
79 * @phy_id: Address of the PHY device
80 * @reg: PHY register to write to
81 * @val: Value to be written into the register
82 *
83 * Return: 0 on success, -ETIMEDOUT on a timeout
84 *
85 * Writes the value to the requested register by first writing the value
86 * into MWD register. The the MCR register is then appropriately setup
87 * to finish the write operation.
88 */
89static int axienet_mdio_write(struct mii_bus *bus, int phy_id, int reg,
90 u16 val)
91{
92 int ret;
93 struct axienet_local *lp = bus->priv;
94
95 dev_dbg(lp->dev, "axienet_mdio_write(phy_id=%i, reg=%x, val=%x)\n",
96 phy_id, reg, val);
97
98 ret = axienet_mdio_wait_until_ready(lp);
99 if (ret < 0)
100 return ret;
101
102 axienet_iow(lp, XAE_MDIO_MWD_OFFSET, (u32) val);
103 axienet_iow(lp, XAE_MDIO_MCR_OFFSET,
104 (((phy_id << XAE_MDIO_MCR_PHYAD_SHIFT) &
105 XAE_MDIO_MCR_PHYAD_MASK) |
106 ((reg << XAE_MDIO_MCR_REGAD_SHIFT) &
107 XAE_MDIO_MCR_REGAD_MASK) |
108 XAE_MDIO_MCR_INITIATE_MASK |
109 XAE_MDIO_MCR_OP_WRITE_MASK));
110
111 ret = axienet_mdio_wait_until_ready(lp);
112 if (ret < 0)
113 return ret;
114 return 0;
115}
116
117/**
118 * axienet_mdio_setup - MDIO setup function
119 * @lp: Pointer to axienet local data structure.
120 * @np: Pointer to device node
121 *
122 * Return: 0 on success, -ETIMEDOUT on a timeout, -ENOMEM when
123 * mdiobus_alloc (to allocate memory for mii bus structure) fails.
124 *
125 * Sets up the MDIO interface by initializing the MDIO clock and enabling the
126 * MDIO interface in hardware. Register the MDIO interface.
127 **/
128int axienet_mdio_setup(struct axienet_local *lp, struct device_node *np)
129{
130 int ret;
131 u32 clk_div, host_clock;
132 struct mii_bus *bus;
133 struct resource res;
134 struct device_node *np1;
135
136 /* clk_div can be calculated by deriving it from the equation:
137 * fMDIO = fHOST / ((1 + clk_div) * 2)
138 *
139 * Where fMDIO <= 2500000, so we get:
140 * fHOST / ((1 + clk_div) * 2) <= 2500000
141 *
142 * Then we get:
143 * 1 / ((1 + clk_div) * 2) <= (2500000 / fHOST)
144 *
145 * Then we get:
146 * 1 / (1 + clk_div) <= ((2500000 * 2) / fHOST)
147 *
148 * Then we get:
149 * 1 / (1 + clk_div) <= (5000000 / fHOST)
150 *
151 * So:
152 * (1 + clk_div) >= (fHOST / 5000000)
153 *
154 * And finally:
155 * clk_div >= (fHOST / 5000000) - 1
156 *
157 * fHOST can be read from the flattened device tree as property
158 * "clock-frequency" from the CPU
159 */
160
161 np1 = of_find_node_by_name(NULL, "cpu");
162 if (!np1) {
163 netdev_warn(lp->ndev, "Could not find CPU device node.\n");
164 netdev_warn(lp->ndev,
165 "Setting MDIO clock divisor to default %d\n",
166 DEFAULT_CLOCK_DIVISOR);
167 clk_div = DEFAULT_CLOCK_DIVISOR;
168 goto issue;
169 }
170 if (of_property_read_u32(np1, "clock-frequency", &host_clock)) {
171 netdev_warn(lp->ndev, "clock-frequency property not found.\n");
172 netdev_warn(lp->ndev,
173 "Setting MDIO clock divisor to default %d\n",
174 DEFAULT_CLOCK_DIVISOR);
175 clk_div = DEFAULT_CLOCK_DIVISOR;
176 of_node_put(np1);
177 goto issue;
178 }
179
180 clk_div = (host_clock / (MAX_MDIO_FREQ * 2)) - 1;
181 /* If there is any remainder from the division of
182 * fHOST / (MAX_MDIO_FREQ * 2), then we need to add
183 * 1 to the clock divisor or we will surely be above 2.5 MHz
184 */
185 if (host_clock % (MAX_MDIO_FREQ * 2))
186 clk_div++;
187
188 netdev_dbg(lp->ndev,
189 "Setting MDIO clock divisor to %u/%u Hz host clock.\n",
190 clk_div, host_clock);
191
192 of_node_put(np1);
193issue:
194 axienet_iow(lp, XAE_MDIO_MC_OFFSET,
195 (((u32) clk_div) | XAE_MDIO_MC_MDIOEN_MASK));
196
197 ret = axienet_mdio_wait_until_ready(lp);
198 if (ret < 0)
199 return ret;
200
201 bus = mdiobus_alloc();
202 if (!bus)
203 return -ENOMEM;
204
205 np1 = of_get_parent(lp->phy_node);
206 of_address_to_resource(np1, 0, &res);
207 snprintf(bus->id, MII_BUS_ID_SIZE, "%.8llx",
208 (unsigned long long) res.start);
209
210 bus->priv = lp;
211 bus->name = "Xilinx Axi Ethernet MDIO";
212 bus->read = axienet_mdio_read;
213 bus->write = axienet_mdio_write;
214 bus->parent = lp->dev;
215 lp->mii_bus = bus;
216
217 ret = of_mdiobus_register(bus, np1);
218 if (ret) {
219 mdiobus_free(bus);
220 return ret;
221 }
222 return 0;
223}
224
225/**
226 * axienet_mdio_teardown - MDIO remove function
227 * @lp: Pointer to axienet local data structure.
228 *
229 * Unregisters the MDIO and frees any associate memory for mii bus.
230 */
231void axienet_mdio_teardown(struct axienet_local *lp)
232{
233 mdiobus_unregister(lp->mii_bus);
234 mdiobus_free(lp->mii_bus);
235 lp->mii_bus = NULL;
236}