Loading...
1// SPDX-License-Identifier: GPL-2.0+
2/*
3 * at24.c - handle most I2C EEPROMs
4 *
5 * Copyright (C) 2005-2007 David Brownell
6 * Copyright (C) 2008 Wolfram Sang, Pengutronix
7 */
8
9#include <linux/kernel.h>
10#include <linux/init.h>
11#include <linux/module.h>
12#include <linux/of_device.h>
13#include <linux/slab.h>
14#include <linux/delay.h>
15#include <linux/mutex.h>
16#include <linux/mod_devicetable.h>
17#include <linux/log2.h>
18#include <linux/bitops.h>
19#include <linux/jiffies.h>
20#include <linux/property.h>
21#include <linux/acpi.h>
22#include <linux/i2c.h>
23#include <linux/nvmem-provider.h>
24#include <linux/regmap.h>
25#include <linux/platform_data/at24.h>
26#include <linux/pm_runtime.h>
27#include <linux/gpio/consumer.h>
28
29/*
30 * I2C EEPROMs from most vendors are inexpensive and mostly interchangeable.
31 * Differences between different vendor product lines (like Atmel AT24C or
32 * MicroChip 24LC, etc) won't much matter for typical read/write access.
33 * There are also I2C RAM chips, likewise interchangeable. One example
34 * would be the PCF8570, which acts like a 24c02 EEPROM (256 bytes).
35 *
36 * However, misconfiguration can lose data. "Set 16-bit memory address"
37 * to a part with 8-bit addressing will overwrite data. Writing with too
38 * big a page size also loses data. And it's not safe to assume that the
39 * conventional addresses 0x50..0x57 only hold eeproms; a PCF8563 RTC
40 * uses 0x51, for just one example.
41 *
42 * Accordingly, explicit board-specific configuration data should be used
43 * in almost all cases. (One partial exception is an SMBus used to access
44 * "SPD" data for DRAM sticks. Those only use 24c02 EEPROMs.)
45 *
46 * So this driver uses "new style" I2C driver binding, expecting to be
47 * told what devices exist. That may be in arch/X/mach-Y/board-Z.c or
48 * similar kernel-resident tables; or, configuration data coming from
49 * a bootloader.
50 *
51 * Other than binding model, current differences from "eeprom" driver are
52 * that this one handles write access and isn't restricted to 24c02 devices.
53 * It also handles larger devices (32 kbit and up) with two-byte addresses,
54 * which won't work on pure SMBus systems.
55 */
56
57struct at24_client {
58 struct i2c_client *client;
59 struct regmap *regmap;
60};
61
62struct at24_data {
63 /*
64 * Lock protects against activities from other Linux tasks,
65 * but not from changes by other I2C masters.
66 */
67 struct mutex lock;
68
69 unsigned int write_max;
70 unsigned int num_addresses;
71 unsigned int offset_adj;
72
73 u32 byte_len;
74 u16 page_size;
75 u8 flags;
76
77 struct nvmem_device *nvmem;
78
79 struct gpio_desc *wp_gpio;
80
81 /*
82 * Some chips tie up multiple I2C addresses; dummy devices reserve
83 * them for us, and we'll use them with SMBus calls.
84 */
85 struct at24_client client[];
86};
87
88/*
89 * This parameter is to help this driver avoid blocking other drivers out
90 * of I2C for potentially troublesome amounts of time. With a 100 kHz I2C
91 * clock, one 256 byte read takes about 1/43 second which is excessive;
92 * but the 1/170 second it takes at 400 kHz may be quite reasonable; and
93 * at 1 MHz (Fm+) a 1/430 second delay could easily be invisible.
94 *
95 * This value is forced to be a power of two so that writes align on pages.
96 */
97static unsigned int at24_io_limit = 128;
98module_param_named(io_limit, at24_io_limit, uint, 0);
99MODULE_PARM_DESC(at24_io_limit, "Maximum bytes per I/O (default 128)");
100
101/*
102 * Specs often allow 5 msec for a page write, sometimes 20 msec;
103 * it's important to recover from write timeouts.
104 */
105static unsigned int at24_write_timeout = 25;
106module_param_named(write_timeout, at24_write_timeout, uint, 0);
107MODULE_PARM_DESC(at24_write_timeout, "Time (in ms) to try writes (default 25)");
108
109/*
110 * Both reads and writes fail if the previous write didn't complete yet. This
111 * macro loops a few times waiting at least long enough for one entire page
112 * write to work while making sure that at least one iteration is run before
113 * checking the break condition.
114 *
115 * It takes two parameters: a variable in which the future timeout in jiffies
116 * will be stored and a temporary variable holding the time of the last
117 * iteration of processing the request. Both should be unsigned integers
118 * holding at least 32 bits.
119 */
120#define at24_loop_until_timeout(tout, op_time) \
121 for (tout = jiffies + msecs_to_jiffies(at24_write_timeout), \
122 op_time = 0; \
123 op_time ? time_before(op_time, tout) : true; \
124 usleep_range(1000, 1500), op_time = jiffies)
125
126struct at24_chip_data {
127 /*
128 * these fields mirror their equivalents in
129 * struct at24_platform_data
130 */
131 u32 byte_len;
132 u8 flags;
133};
134
135#define AT24_CHIP_DATA(_name, _len, _flags) \
136 static const struct at24_chip_data _name = { \
137 .byte_len = _len, .flags = _flags, \
138 }
139
140/* needs 8 addresses as A0-A2 are ignored */
141AT24_CHIP_DATA(at24_data_24c00, 128 / 8, AT24_FLAG_TAKE8ADDR);
142/* old variants can't be handled with this generic entry! */
143AT24_CHIP_DATA(at24_data_24c01, 1024 / 8, 0);
144AT24_CHIP_DATA(at24_data_24cs01, 16,
145 AT24_FLAG_SERIAL | AT24_FLAG_READONLY);
146AT24_CHIP_DATA(at24_data_24c02, 2048 / 8, 0);
147AT24_CHIP_DATA(at24_data_24cs02, 16,
148 AT24_FLAG_SERIAL | AT24_FLAG_READONLY);
149AT24_CHIP_DATA(at24_data_24mac402, 48 / 8,
150 AT24_FLAG_MAC | AT24_FLAG_READONLY);
151AT24_CHIP_DATA(at24_data_24mac602, 64 / 8,
152 AT24_FLAG_MAC | AT24_FLAG_READONLY);
153/* spd is a 24c02 in memory DIMMs */
154AT24_CHIP_DATA(at24_data_spd, 2048 / 8,
155 AT24_FLAG_READONLY | AT24_FLAG_IRUGO);
156AT24_CHIP_DATA(at24_data_24c04, 4096 / 8, 0);
157AT24_CHIP_DATA(at24_data_24cs04, 16,
158 AT24_FLAG_SERIAL | AT24_FLAG_READONLY);
159/* 24rf08 quirk is handled at i2c-core */
160AT24_CHIP_DATA(at24_data_24c08, 8192 / 8, 0);
161AT24_CHIP_DATA(at24_data_24cs08, 16,
162 AT24_FLAG_SERIAL | AT24_FLAG_READONLY);
163AT24_CHIP_DATA(at24_data_24c16, 16384 / 8, 0);
164AT24_CHIP_DATA(at24_data_24cs16, 16,
165 AT24_FLAG_SERIAL | AT24_FLAG_READONLY);
166AT24_CHIP_DATA(at24_data_24c32, 32768 / 8, AT24_FLAG_ADDR16);
167AT24_CHIP_DATA(at24_data_24cs32, 16,
168 AT24_FLAG_ADDR16 | AT24_FLAG_SERIAL | AT24_FLAG_READONLY);
169AT24_CHIP_DATA(at24_data_24c64, 65536 / 8, AT24_FLAG_ADDR16);
170AT24_CHIP_DATA(at24_data_24cs64, 16,
171 AT24_FLAG_ADDR16 | AT24_FLAG_SERIAL | AT24_FLAG_READONLY);
172AT24_CHIP_DATA(at24_data_24c128, 131072 / 8, AT24_FLAG_ADDR16);
173AT24_CHIP_DATA(at24_data_24c256, 262144 / 8, AT24_FLAG_ADDR16);
174AT24_CHIP_DATA(at24_data_24c512, 524288 / 8, AT24_FLAG_ADDR16);
175AT24_CHIP_DATA(at24_data_24c1024, 1048576 / 8, AT24_FLAG_ADDR16);
176/* identical to 24c08 ? */
177AT24_CHIP_DATA(at24_data_INT3499, 8192 / 8, 0);
178
179static const struct i2c_device_id at24_ids[] = {
180 { "24c00", (kernel_ulong_t)&at24_data_24c00 },
181 { "24c01", (kernel_ulong_t)&at24_data_24c01 },
182 { "24cs01", (kernel_ulong_t)&at24_data_24cs01 },
183 { "24c02", (kernel_ulong_t)&at24_data_24c02 },
184 { "24cs02", (kernel_ulong_t)&at24_data_24cs02 },
185 { "24mac402", (kernel_ulong_t)&at24_data_24mac402 },
186 { "24mac602", (kernel_ulong_t)&at24_data_24mac602 },
187 { "spd", (kernel_ulong_t)&at24_data_spd },
188 { "24c04", (kernel_ulong_t)&at24_data_24c04 },
189 { "24cs04", (kernel_ulong_t)&at24_data_24cs04 },
190 { "24c08", (kernel_ulong_t)&at24_data_24c08 },
191 { "24cs08", (kernel_ulong_t)&at24_data_24cs08 },
192 { "24c16", (kernel_ulong_t)&at24_data_24c16 },
193 { "24cs16", (kernel_ulong_t)&at24_data_24cs16 },
194 { "24c32", (kernel_ulong_t)&at24_data_24c32 },
195 { "24cs32", (kernel_ulong_t)&at24_data_24cs32 },
196 { "24c64", (kernel_ulong_t)&at24_data_24c64 },
197 { "24cs64", (kernel_ulong_t)&at24_data_24cs64 },
198 { "24c128", (kernel_ulong_t)&at24_data_24c128 },
199 { "24c256", (kernel_ulong_t)&at24_data_24c256 },
200 { "24c512", (kernel_ulong_t)&at24_data_24c512 },
201 { "24c1024", (kernel_ulong_t)&at24_data_24c1024 },
202 { "at24", 0 },
203 { /* END OF LIST */ }
204};
205MODULE_DEVICE_TABLE(i2c, at24_ids);
206
207static const struct of_device_id at24_of_match[] = {
208 { .compatible = "atmel,24c00", .data = &at24_data_24c00 },
209 { .compatible = "atmel,24c01", .data = &at24_data_24c01 },
210 { .compatible = "atmel,24cs01", .data = &at24_data_24cs01 },
211 { .compatible = "atmel,24c02", .data = &at24_data_24c02 },
212 { .compatible = "atmel,24cs02", .data = &at24_data_24cs02 },
213 { .compatible = "atmel,24mac402", .data = &at24_data_24mac402 },
214 { .compatible = "atmel,24mac602", .data = &at24_data_24mac602 },
215 { .compatible = "atmel,spd", .data = &at24_data_spd },
216 { .compatible = "atmel,24c04", .data = &at24_data_24c04 },
217 { .compatible = "atmel,24cs04", .data = &at24_data_24cs04 },
218 { .compatible = "atmel,24c08", .data = &at24_data_24c08 },
219 { .compatible = "atmel,24cs08", .data = &at24_data_24cs08 },
220 { .compatible = "atmel,24c16", .data = &at24_data_24c16 },
221 { .compatible = "atmel,24cs16", .data = &at24_data_24cs16 },
222 { .compatible = "atmel,24c32", .data = &at24_data_24c32 },
223 { .compatible = "atmel,24cs32", .data = &at24_data_24cs32 },
224 { .compatible = "atmel,24c64", .data = &at24_data_24c64 },
225 { .compatible = "atmel,24cs64", .data = &at24_data_24cs64 },
226 { .compatible = "atmel,24c128", .data = &at24_data_24c128 },
227 { .compatible = "atmel,24c256", .data = &at24_data_24c256 },
228 { .compatible = "atmel,24c512", .data = &at24_data_24c512 },
229 { .compatible = "atmel,24c1024", .data = &at24_data_24c1024 },
230 { /* END OF LIST */ },
231};
232MODULE_DEVICE_TABLE(of, at24_of_match);
233
234static const struct acpi_device_id at24_acpi_ids[] = {
235 { "INT3499", (kernel_ulong_t)&at24_data_INT3499 },
236 { /* END OF LIST */ }
237};
238MODULE_DEVICE_TABLE(acpi, at24_acpi_ids);
239
240/*
241 * This routine supports chips which consume multiple I2C addresses. It
242 * computes the addressing information to be used for a given r/w request.
243 * Assumes that sanity checks for offset happened at sysfs-layer.
244 *
245 * Slave address and byte offset derive from the offset. Always
246 * set the byte address; on a multi-master board, another master
247 * may have changed the chip's "current" address pointer.
248 */
249static struct at24_client *at24_translate_offset(struct at24_data *at24,
250 unsigned int *offset)
251{
252 unsigned int i;
253
254 if (at24->flags & AT24_FLAG_ADDR16) {
255 i = *offset >> 16;
256 *offset &= 0xffff;
257 } else {
258 i = *offset >> 8;
259 *offset &= 0xff;
260 }
261
262 return &at24->client[i];
263}
264
265static struct device *at24_base_client_dev(struct at24_data *at24)
266{
267 return &at24->client[0].client->dev;
268}
269
270static size_t at24_adjust_read_count(struct at24_data *at24,
271 unsigned int offset, size_t count)
272{
273 unsigned int bits;
274 size_t remainder;
275
276 /*
277 * In case of multi-address chips that don't rollover reads to
278 * the next slave address: truncate the count to the slave boundary,
279 * so that the read never straddles slaves.
280 */
281 if (at24->flags & AT24_FLAG_NO_RDROL) {
282 bits = (at24->flags & AT24_FLAG_ADDR16) ? 16 : 8;
283 remainder = BIT(bits) - offset;
284 if (count > remainder)
285 count = remainder;
286 }
287
288 if (count > at24_io_limit)
289 count = at24_io_limit;
290
291 return count;
292}
293
294static ssize_t at24_regmap_read(struct at24_data *at24, char *buf,
295 unsigned int offset, size_t count)
296{
297 unsigned long timeout, read_time;
298 struct at24_client *at24_client;
299 struct i2c_client *client;
300 struct regmap *regmap;
301 int ret;
302
303 at24_client = at24_translate_offset(at24, &offset);
304 regmap = at24_client->regmap;
305 client = at24_client->client;
306 count = at24_adjust_read_count(at24, offset, count);
307
308 /* adjust offset for mac and serial read ops */
309 offset += at24->offset_adj;
310
311 at24_loop_until_timeout(timeout, read_time) {
312 ret = regmap_bulk_read(regmap, offset, buf, count);
313 dev_dbg(&client->dev, "read %zu@%d --> %d (%ld)\n",
314 count, offset, ret, jiffies);
315 if (!ret)
316 return count;
317 }
318
319 return -ETIMEDOUT;
320}
321
322/*
323 * Note that if the hardware write-protect pin is pulled high, the whole
324 * chip is normally write protected. But there are plenty of product
325 * variants here, including OTP fuses and partial chip protect.
326 *
327 * We only use page mode writes; the alternative is sloooow. These routines
328 * write at most one page.
329 */
330
331static size_t at24_adjust_write_count(struct at24_data *at24,
332 unsigned int offset, size_t count)
333{
334 unsigned int next_page;
335
336 /* write_max is at most a page */
337 if (count > at24->write_max)
338 count = at24->write_max;
339
340 /* Never roll over backwards, to the start of this page */
341 next_page = roundup(offset + 1, at24->page_size);
342 if (offset + count > next_page)
343 count = next_page - offset;
344
345 return count;
346}
347
348static ssize_t at24_regmap_write(struct at24_data *at24, const char *buf,
349 unsigned int offset, size_t count)
350{
351 unsigned long timeout, write_time;
352 struct at24_client *at24_client;
353 struct i2c_client *client;
354 struct regmap *regmap;
355 int ret;
356
357 at24_client = at24_translate_offset(at24, &offset);
358 regmap = at24_client->regmap;
359 client = at24_client->client;
360 count = at24_adjust_write_count(at24, offset, count);
361
362 at24_loop_until_timeout(timeout, write_time) {
363 ret = regmap_bulk_write(regmap, offset, buf, count);
364 dev_dbg(&client->dev, "write %zu@%d --> %d (%ld)\n",
365 count, offset, ret, jiffies);
366 if (!ret)
367 return count;
368 }
369
370 return -ETIMEDOUT;
371}
372
373static int at24_read(void *priv, unsigned int off, void *val, size_t count)
374{
375 struct at24_data *at24;
376 struct device *dev;
377 char *buf = val;
378 int ret;
379
380 at24 = priv;
381 dev = at24_base_client_dev(at24);
382
383 if (unlikely(!count))
384 return count;
385
386 if (off + count > at24->byte_len)
387 return -EINVAL;
388
389 ret = pm_runtime_get_sync(dev);
390 if (ret < 0) {
391 pm_runtime_put_noidle(dev);
392 return ret;
393 }
394
395 /*
396 * Read data from chip, protecting against concurrent updates
397 * from this host, but not from other I2C masters.
398 */
399 mutex_lock(&at24->lock);
400
401 while (count) {
402 ret = at24_regmap_read(at24, buf, off, count);
403 if (ret < 0) {
404 mutex_unlock(&at24->lock);
405 pm_runtime_put(dev);
406 return ret;
407 }
408 buf += ret;
409 off += ret;
410 count -= ret;
411 }
412
413 mutex_unlock(&at24->lock);
414
415 pm_runtime_put(dev);
416
417 return 0;
418}
419
420static int at24_write(void *priv, unsigned int off, void *val, size_t count)
421{
422 struct at24_data *at24;
423 struct device *dev;
424 char *buf = val;
425 int ret;
426
427 at24 = priv;
428 dev = at24_base_client_dev(at24);
429
430 if (unlikely(!count))
431 return -EINVAL;
432
433 if (off + count > at24->byte_len)
434 return -EINVAL;
435
436 ret = pm_runtime_get_sync(dev);
437 if (ret < 0) {
438 pm_runtime_put_noidle(dev);
439 return ret;
440 }
441
442 /*
443 * Write data to chip, protecting against concurrent updates
444 * from this host, but not from other I2C masters.
445 */
446 mutex_lock(&at24->lock);
447 gpiod_set_value_cansleep(at24->wp_gpio, 0);
448
449 while (count) {
450 ret = at24_regmap_write(at24, buf, off, count);
451 if (ret < 0) {
452 gpiod_set_value_cansleep(at24->wp_gpio, 1);
453 mutex_unlock(&at24->lock);
454 pm_runtime_put(dev);
455 return ret;
456 }
457 buf += ret;
458 off += ret;
459 count -= ret;
460 }
461
462 gpiod_set_value_cansleep(at24->wp_gpio, 1);
463 mutex_unlock(&at24->lock);
464
465 pm_runtime_put(dev);
466
467 return 0;
468}
469
470static void at24_properties_to_pdata(struct device *dev,
471 struct at24_platform_data *chip)
472{
473 int err;
474 u32 val;
475
476 if (device_property_present(dev, "read-only"))
477 chip->flags |= AT24_FLAG_READONLY;
478 if (device_property_present(dev, "no-read-rollover"))
479 chip->flags |= AT24_FLAG_NO_RDROL;
480
481 err = device_property_read_u32(dev, "size", &val);
482 if (!err)
483 chip->byte_len = val;
484
485 err = device_property_read_u32(dev, "pagesize", &val);
486 if (!err) {
487 chip->page_size = val;
488 } else {
489 /*
490 * This is slow, but we can't know all eeproms, so we better
491 * play safe. Specifying custom eeprom-types via platform_data
492 * is recommended anyhow.
493 */
494 chip->page_size = 1;
495 }
496}
497
498static int at24_get_pdata(struct device *dev, struct at24_platform_data *pdata)
499{
500 struct device_node *of_node = dev->of_node;
501 const struct at24_chip_data *cdata;
502 const struct i2c_device_id *id;
503 struct at24_platform_data *pd;
504
505 pd = dev_get_platdata(dev);
506 if (pd) {
507 memcpy(pdata, pd, sizeof(*pdata));
508 return 0;
509 }
510
511 id = i2c_match_id(at24_ids, to_i2c_client(dev));
512
513 /*
514 * The I2C core allows OF nodes compatibles to match against the
515 * I2C device ID table as a fallback, so check not only if an OF
516 * node is present but also if it matches an OF device ID entry.
517 */
518 if (of_node && of_match_device(at24_of_match, dev))
519 cdata = of_device_get_match_data(dev);
520 else if (id)
521 cdata = (void *)id->driver_data;
522 else
523 cdata = acpi_device_get_match_data(dev);
524
525 if (!cdata)
526 return -ENODEV;
527
528 pdata->byte_len = cdata->byte_len;
529 pdata->flags = cdata->flags;
530 at24_properties_to_pdata(dev, pdata);
531
532 return 0;
533}
534
535static unsigned int at24_get_offset_adj(u8 flags, unsigned int byte_len)
536{
537 if (flags & AT24_FLAG_MAC) {
538 /* EUI-48 starts from 0x9a, EUI-64 from 0x98 */
539 return 0xa0 - byte_len;
540 } else if (flags & AT24_FLAG_SERIAL && flags & AT24_FLAG_ADDR16) {
541 /*
542 * For 16 bit address pointers, the word address must contain
543 * a '10' sequence in bits 11 and 10 regardless of the
544 * intended position of the address pointer.
545 */
546 return 0x0800;
547 } else if (flags & AT24_FLAG_SERIAL) {
548 /*
549 * Otherwise the word address must begin with a '10' sequence,
550 * regardless of the intended address.
551 */
552 return 0x0080;
553 } else {
554 return 0;
555 }
556}
557
558static int at24_probe(struct i2c_client *client)
559{
560 struct regmap_config regmap_config = { };
561 struct nvmem_config nvmem_config = { };
562 struct at24_platform_data pdata = { };
563 struct device *dev = &client->dev;
564 bool i2c_fn_i2c, i2c_fn_block;
565 unsigned int i, num_addresses;
566 struct at24_data *at24;
567 struct regmap *regmap;
568 size_t at24_size;
569 bool writable;
570 u8 test_byte;
571 int err;
572
573 i2c_fn_i2c = i2c_check_functionality(client->adapter, I2C_FUNC_I2C);
574 i2c_fn_block = i2c_check_functionality(client->adapter,
575 I2C_FUNC_SMBUS_WRITE_I2C_BLOCK);
576
577 err = at24_get_pdata(dev, &pdata);
578 if (err)
579 return err;
580
581 if (!i2c_fn_i2c && !i2c_fn_block)
582 pdata.page_size = 1;
583
584 if (!pdata.page_size) {
585 dev_err(dev, "page_size must not be 0!\n");
586 return -EINVAL;
587 }
588
589 if (!is_power_of_2(pdata.page_size))
590 dev_warn(dev, "page_size looks suspicious (no power of 2)!\n");
591
592 if (pdata.flags & AT24_FLAG_TAKE8ADDR)
593 num_addresses = 8;
594 else
595 num_addresses = DIV_ROUND_UP(pdata.byte_len,
596 (pdata.flags & AT24_FLAG_ADDR16) ? 65536 : 256);
597
598 if ((pdata.flags & AT24_FLAG_SERIAL) && (pdata.flags & AT24_FLAG_MAC)) {
599 dev_err(dev,
600 "invalid device data - cannot have both AT24_FLAG_SERIAL & AT24_FLAG_MAC.");
601 return -EINVAL;
602 }
603
604 regmap_config.val_bits = 8;
605 regmap_config.reg_bits = (pdata.flags & AT24_FLAG_ADDR16) ? 16 : 8;
606 regmap_config.disable_locking = true;
607
608 regmap = devm_regmap_init_i2c(client, ®map_config);
609 if (IS_ERR(regmap))
610 return PTR_ERR(regmap);
611
612 at24_size = sizeof(*at24) + num_addresses * sizeof(struct at24_client);
613 at24 = devm_kzalloc(dev, at24_size, GFP_KERNEL);
614 if (!at24)
615 return -ENOMEM;
616
617 mutex_init(&at24->lock);
618 at24->byte_len = pdata.byte_len;
619 at24->page_size = pdata.page_size;
620 at24->flags = pdata.flags;
621 at24->num_addresses = num_addresses;
622 at24->offset_adj = at24_get_offset_adj(pdata.flags, pdata.byte_len);
623 at24->client[0].client = client;
624 at24->client[0].regmap = regmap;
625
626 at24->wp_gpio = devm_gpiod_get_optional(dev, "wp", GPIOD_OUT_HIGH);
627 if (IS_ERR(at24->wp_gpio))
628 return PTR_ERR(at24->wp_gpio);
629
630 writable = !(pdata.flags & AT24_FLAG_READONLY);
631 if (writable) {
632 at24->write_max = min_t(unsigned int,
633 pdata.page_size, at24_io_limit);
634 if (!i2c_fn_i2c && at24->write_max > I2C_SMBUS_BLOCK_MAX)
635 at24->write_max = I2C_SMBUS_BLOCK_MAX;
636 }
637
638 /* use dummy devices for multiple-address chips */
639 for (i = 1; i < num_addresses; i++) {
640 at24->client[i].client = i2c_new_dummy(client->adapter,
641 client->addr + i);
642 if (!at24->client[i].client) {
643 dev_err(dev, "address 0x%02x unavailable\n",
644 client->addr + i);
645 err = -EADDRINUSE;
646 goto err_clients;
647 }
648 at24->client[i].regmap = devm_regmap_init_i2c(
649 at24->client[i].client,
650 ®map_config);
651 if (IS_ERR(at24->client[i].regmap)) {
652 err = PTR_ERR(at24->client[i].regmap);
653 goto err_clients;
654 }
655 }
656
657 i2c_set_clientdata(client, at24);
658
659 /* enable runtime pm */
660 pm_runtime_set_active(dev);
661 pm_runtime_enable(dev);
662
663 /*
664 * Perform a one-byte test read to verify that the
665 * chip is functional.
666 */
667 err = at24_read(at24, 0, &test_byte, 1);
668 pm_runtime_idle(dev);
669 if (err) {
670 err = -ENODEV;
671 goto err_clients;
672 }
673
674 nvmem_config.name = dev_name(dev);
675 nvmem_config.dev = dev;
676 nvmem_config.read_only = !writable;
677 nvmem_config.root_only = true;
678 nvmem_config.owner = THIS_MODULE;
679 nvmem_config.compat = true;
680 nvmem_config.base_dev = dev;
681 nvmem_config.reg_read = at24_read;
682 nvmem_config.reg_write = at24_write;
683 nvmem_config.priv = at24;
684 nvmem_config.stride = 1;
685 nvmem_config.word_size = 1;
686 nvmem_config.size = pdata.byte_len;
687
688 at24->nvmem = nvmem_register(&nvmem_config);
689 if (IS_ERR(at24->nvmem)) {
690 err = PTR_ERR(at24->nvmem);
691 goto err_clients;
692 }
693
694 dev_info(dev, "%u byte %s EEPROM, %s, %u bytes/write\n",
695 pdata.byte_len, client->name,
696 writable ? "writable" : "read-only", at24->write_max);
697
698 /* export data to kernel code */
699 if (pdata.setup)
700 pdata.setup(at24->nvmem, pdata.context);
701
702 return 0;
703
704err_clients:
705 for (i = 1; i < num_addresses; i++)
706 if (at24->client[i].client)
707 i2c_unregister_device(at24->client[i].client);
708
709 pm_runtime_disable(dev);
710
711 return err;
712}
713
714static int at24_remove(struct i2c_client *client)
715{
716 struct at24_data *at24;
717 int i;
718
719 at24 = i2c_get_clientdata(client);
720
721 nvmem_unregister(at24->nvmem);
722
723 for (i = 1; i < at24->num_addresses; i++)
724 i2c_unregister_device(at24->client[i].client);
725
726 pm_runtime_disable(&client->dev);
727 pm_runtime_set_suspended(&client->dev);
728
729 return 0;
730}
731
732static struct i2c_driver at24_driver = {
733 .driver = {
734 .name = "at24",
735 .of_match_table = at24_of_match,
736 .acpi_match_table = ACPI_PTR(at24_acpi_ids),
737 },
738 .probe_new = at24_probe,
739 .remove = at24_remove,
740 .id_table = at24_ids,
741};
742
743static int __init at24_init(void)
744{
745 if (!at24_io_limit) {
746 pr_err("at24: at24_io_limit must not be 0!\n");
747 return -EINVAL;
748 }
749
750 at24_io_limit = rounddown_pow_of_two(at24_io_limit);
751 return i2c_add_driver(&at24_driver);
752}
753module_init(at24_init);
754
755static void __exit at24_exit(void)
756{
757 i2c_del_driver(&at24_driver);
758}
759module_exit(at24_exit);
760
761MODULE_DESCRIPTION("Driver for most I2C EEPROMs");
762MODULE_AUTHOR("David Brownell and Wolfram Sang");
763MODULE_LICENSE("GPL");
1/*
2 * at24.c - handle most I2C EEPROMs
3 *
4 * Copyright (C) 2005-2007 David Brownell
5 * Copyright (C) 2008 Wolfram Sang, Pengutronix
6 *
7 * This program is free software; you can redistribute it and/or modify
8 * it under the terms of the GNU General Public License as published by
9 * the Free Software Foundation; either version 2 of the License, or
10 * (at your option) any later version.
11 */
12#include <linux/kernel.h>
13#include <linux/init.h>
14#include <linux/module.h>
15#include <linux/slab.h>
16#include <linux/delay.h>
17#include <linux/mutex.h>
18#include <linux/mod_devicetable.h>
19#include <linux/log2.h>
20#include <linux/bitops.h>
21#include <linux/jiffies.h>
22#include <linux/of.h>
23#include <linux/acpi.h>
24#include <linux/i2c.h>
25#include <linux/nvmem-provider.h>
26#include <linux/platform_data/at24.h>
27
28/*
29 * I2C EEPROMs from most vendors are inexpensive and mostly interchangeable.
30 * Differences between different vendor product lines (like Atmel AT24C or
31 * MicroChip 24LC, etc) won't much matter for typical read/write access.
32 * There are also I2C RAM chips, likewise interchangeable. One example
33 * would be the PCF8570, which acts like a 24c02 EEPROM (256 bytes).
34 *
35 * However, misconfiguration can lose data. "Set 16-bit memory address"
36 * to a part with 8-bit addressing will overwrite data. Writing with too
37 * big a page size also loses data. And it's not safe to assume that the
38 * conventional addresses 0x50..0x57 only hold eeproms; a PCF8563 RTC
39 * uses 0x51, for just one example.
40 *
41 * Accordingly, explicit board-specific configuration data should be used
42 * in almost all cases. (One partial exception is an SMBus used to access
43 * "SPD" data for DRAM sticks. Those only use 24c02 EEPROMs.)
44 *
45 * So this driver uses "new style" I2C driver binding, expecting to be
46 * told what devices exist. That may be in arch/X/mach-Y/board-Z.c or
47 * similar kernel-resident tables; or, configuration data coming from
48 * a bootloader.
49 *
50 * Other than binding model, current differences from "eeprom" driver are
51 * that this one handles write access and isn't restricted to 24c02 devices.
52 * It also handles larger devices (32 kbit and up) with two-byte addresses,
53 * which won't work on pure SMBus systems.
54 */
55
56struct at24_data {
57 struct at24_platform_data chip;
58 int use_smbus;
59 int use_smbus_write;
60
61 ssize_t (*read_func)(struct at24_data *, char *, unsigned int, size_t);
62 ssize_t (*write_func)(struct at24_data *,
63 const char *, unsigned int, size_t);
64
65 /*
66 * Lock protects against activities from other Linux tasks,
67 * but not from changes by other I2C masters.
68 */
69 struct mutex lock;
70
71 u8 *writebuf;
72 unsigned write_max;
73 unsigned num_addresses;
74
75 struct nvmem_config nvmem_config;
76 struct nvmem_device *nvmem;
77
78 /*
79 * Some chips tie up multiple I2C addresses; dummy devices reserve
80 * them for us, and we'll use them with SMBus calls.
81 */
82 struct i2c_client *client[];
83};
84
85/*
86 * This parameter is to help this driver avoid blocking other drivers out
87 * of I2C for potentially troublesome amounts of time. With a 100 kHz I2C
88 * clock, one 256 byte read takes about 1/43 second which is excessive;
89 * but the 1/170 second it takes at 400 kHz may be quite reasonable; and
90 * at 1 MHz (Fm+) a 1/430 second delay could easily be invisible.
91 *
92 * This value is forced to be a power of two so that writes align on pages.
93 */
94static unsigned io_limit = 128;
95module_param(io_limit, uint, 0);
96MODULE_PARM_DESC(io_limit, "Maximum bytes per I/O (default 128)");
97
98/*
99 * Specs often allow 5 msec for a page write, sometimes 20 msec;
100 * it's important to recover from write timeouts.
101 */
102static unsigned write_timeout = 25;
103module_param(write_timeout, uint, 0);
104MODULE_PARM_DESC(write_timeout, "Time (in ms) to try writes (default 25)");
105
106#define AT24_SIZE_BYTELEN 5
107#define AT24_SIZE_FLAGS 8
108
109#define AT24_BITMASK(x) (BIT(x) - 1)
110
111/* create non-zero magic value for given eeprom parameters */
112#define AT24_DEVICE_MAGIC(_len, _flags) \
113 ((1 << AT24_SIZE_FLAGS | (_flags)) \
114 << AT24_SIZE_BYTELEN | ilog2(_len))
115
116/*
117 * Both reads and writes fail if the previous write didn't complete yet. This
118 * macro loops a few times waiting at least long enough for one entire page
119 * write to work while making sure that at least one iteration is run before
120 * checking the break condition.
121 *
122 * It takes two parameters: a variable in which the future timeout in jiffies
123 * will be stored and a temporary variable holding the time of the last
124 * iteration of processing the request. Both should be unsigned integers
125 * holding at least 32 bits.
126 */
127#define loop_until_timeout(tout, op_time) \
128 for (tout = jiffies + msecs_to_jiffies(write_timeout), op_time = 0; \
129 op_time ? time_before(op_time, tout) : true; \
130 usleep_range(1000, 1500), op_time = jiffies)
131
132static const struct i2c_device_id at24_ids[] = {
133 /* needs 8 addresses as A0-A2 are ignored */
134 { "24c00", AT24_DEVICE_MAGIC(128 / 8, AT24_FLAG_TAKE8ADDR) },
135 /* old variants can't be handled with this generic entry! */
136 { "24c01", AT24_DEVICE_MAGIC(1024 / 8, 0) },
137 { "24cs01", AT24_DEVICE_MAGIC(16,
138 AT24_FLAG_SERIAL | AT24_FLAG_READONLY) },
139 { "24c02", AT24_DEVICE_MAGIC(2048 / 8, 0) },
140 { "24cs02", AT24_DEVICE_MAGIC(16,
141 AT24_FLAG_SERIAL | AT24_FLAG_READONLY) },
142 { "24mac402", AT24_DEVICE_MAGIC(48 / 8,
143 AT24_FLAG_MAC | AT24_FLAG_READONLY) },
144 { "24mac602", AT24_DEVICE_MAGIC(64 / 8,
145 AT24_FLAG_MAC | AT24_FLAG_READONLY) },
146 /* spd is a 24c02 in memory DIMMs */
147 { "spd", AT24_DEVICE_MAGIC(2048 / 8,
148 AT24_FLAG_READONLY | AT24_FLAG_IRUGO) },
149 { "24c04", AT24_DEVICE_MAGIC(4096 / 8, 0) },
150 { "24cs04", AT24_DEVICE_MAGIC(16,
151 AT24_FLAG_SERIAL | AT24_FLAG_READONLY) },
152 /* 24rf08 quirk is handled at i2c-core */
153 { "24c08", AT24_DEVICE_MAGIC(8192 / 8, 0) },
154 { "24cs08", AT24_DEVICE_MAGIC(16,
155 AT24_FLAG_SERIAL | AT24_FLAG_READONLY) },
156 { "24c16", AT24_DEVICE_MAGIC(16384 / 8, 0) },
157 { "24cs16", AT24_DEVICE_MAGIC(16,
158 AT24_FLAG_SERIAL | AT24_FLAG_READONLY) },
159 { "24c32", AT24_DEVICE_MAGIC(32768 / 8, AT24_FLAG_ADDR16) },
160 { "24cs32", AT24_DEVICE_MAGIC(16,
161 AT24_FLAG_ADDR16 |
162 AT24_FLAG_SERIAL |
163 AT24_FLAG_READONLY) },
164 { "24c64", AT24_DEVICE_MAGIC(65536 / 8, AT24_FLAG_ADDR16) },
165 { "24cs64", AT24_DEVICE_MAGIC(16,
166 AT24_FLAG_ADDR16 |
167 AT24_FLAG_SERIAL |
168 AT24_FLAG_READONLY) },
169 { "24c128", AT24_DEVICE_MAGIC(131072 / 8, AT24_FLAG_ADDR16) },
170 { "24c256", AT24_DEVICE_MAGIC(262144 / 8, AT24_FLAG_ADDR16) },
171 { "24c512", AT24_DEVICE_MAGIC(524288 / 8, AT24_FLAG_ADDR16) },
172 { "24c1024", AT24_DEVICE_MAGIC(1048576 / 8, AT24_FLAG_ADDR16) },
173 { "at24", 0 },
174 { /* END OF LIST */ }
175};
176MODULE_DEVICE_TABLE(i2c, at24_ids);
177
178static const struct acpi_device_id at24_acpi_ids[] = {
179 { "INT3499", AT24_DEVICE_MAGIC(8192 / 8, 0) },
180 { }
181};
182MODULE_DEVICE_TABLE(acpi, at24_acpi_ids);
183
184/*-------------------------------------------------------------------------*/
185
186/*
187 * This routine supports chips which consume multiple I2C addresses. It
188 * computes the addressing information to be used for a given r/w request.
189 * Assumes that sanity checks for offset happened at sysfs-layer.
190 *
191 * Slave address and byte offset derive from the offset. Always
192 * set the byte address; on a multi-master board, another master
193 * may have changed the chip's "current" address pointer.
194 *
195 * REVISIT some multi-address chips don't rollover page reads to
196 * the next slave address, so we may need to truncate the count.
197 * Those chips might need another quirk flag.
198 *
199 * If the real hardware used four adjacent 24c02 chips and that
200 * were misconfigured as one 24c08, that would be a similar effect:
201 * one "eeprom" file not four, but larger reads would fail when
202 * they crossed certain pages.
203 */
204static struct i2c_client *at24_translate_offset(struct at24_data *at24,
205 unsigned int *offset)
206{
207 unsigned i;
208
209 if (at24->chip.flags & AT24_FLAG_ADDR16) {
210 i = *offset >> 16;
211 *offset &= 0xffff;
212 } else {
213 i = *offset >> 8;
214 *offset &= 0xff;
215 }
216
217 return at24->client[i];
218}
219
220static ssize_t at24_eeprom_read_smbus(struct at24_data *at24, char *buf,
221 unsigned int offset, size_t count)
222{
223 unsigned long timeout, read_time;
224 struct i2c_client *client;
225 int status;
226
227 client = at24_translate_offset(at24, &offset);
228
229 if (count > io_limit)
230 count = io_limit;
231
232 /* Smaller eeproms can work given some SMBus extension calls */
233 if (count > I2C_SMBUS_BLOCK_MAX)
234 count = I2C_SMBUS_BLOCK_MAX;
235
236 loop_until_timeout(timeout, read_time) {
237 status = i2c_smbus_read_i2c_block_data_or_emulated(client,
238 offset,
239 count, buf);
240
241 dev_dbg(&client->dev, "read %zu@%d --> %d (%ld)\n",
242 count, offset, status, jiffies);
243
244 if (status == count)
245 return count;
246 }
247
248 return -ETIMEDOUT;
249}
250
251static ssize_t at24_eeprom_read_i2c(struct at24_data *at24, char *buf,
252 unsigned int offset, size_t count)
253{
254 unsigned long timeout, read_time;
255 struct i2c_client *client;
256 struct i2c_msg msg[2];
257 int status, i;
258 u8 msgbuf[2];
259
260 memset(msg, 0, sizeof(msg));
261 client = at24_translate_offset(at24, &offset);
262
263 if (count > io_limit)
264 count = io_limit;
265
266 /*
267 * When we have a better choice than SMBus calls, use a combined I2C
268 * message. Write address; then read up to io_limit data bytes. Note
269 * that read page rollover helps us here (unlike writes). msgbuf is
270 * u8 and will cast to our needs.
271 */
272 i = 0;
273 if (at24->chip.flags & AT24_FLAG_ADDR16)
274 msgbuf[i++] = offset >> 8;
275 msgbuf[i++] = offset;
276
277 msg[0].addr = client->addr;
278 msg[0].buf = msgbuf;
279 msg[0].len = i;
280
281 msg[1].addr = client->addr;
282 msg[1].flags = I2C_M_RD;
283 msg[1].buf = buf;
284 msg[1].len = count;
285
286 loop_until_timeout(timeout, read_time) {
287 status = i2c_transfer(client->adapter, msg, 2);
288 if (status == 2)
289 status = count;
290
291 dev_dbg(&client->dev, "read %zu@%d --> %d (%ld)\n",
292 count, offset, status, jiffies);
293
294 if (status == count)
295 return count;
296 }
297
298 return -ETIMEDOUT;
299}
300
301static ssize_t at24_eeprom_read_serial(struct at24_data *at24, char *buf,
302 unsigned int offset, size_t count)
303{
304 unsigned long timeout, read_time;
305 struct i2c_client *client;
306 struct i2c_msg msg[2];
307 u8 addrbuf[2];
308 int status;
309
310 client = at24_translate_offset(at24, &offset);
311
312 memset(msg, 0, sizeof(msg));
313 msg[0].addr = client->addr;
314 msg[0].buf = addrbuf;
315
316 /*
317 * The address pointer of the device is shared between the regular
318 * EEPROM array and the serial number block. The dummy write (part of
319 * the sequential read protocol) ensures the address pointer is reset
320 * to the desired position.
321 */
322 if (at24->chip.flags & AT24_FLAG_ADDR16) {
323 /*
324 * For 16 bit address pointers, the word address must contain
325 * a '10' sequence in bits 11 and 10 regardless of the
326 * intended position of the address pointer.
327 */
328 addrbuf[0] = 0x08;
329 addrbuf[1] = offset;
330 msg[0].len = 2;
331 } else {
332 /*
333 * Otherwise the word address must begin with a '10' sequence,
334 * regardless of the intended address.
335 */
336 addrbuf[0] = 0x80 + offset;
337 msg[0].len = 1;
338 }
339
340 msg[1].addr = client->addr;
341 msg[1].flags = I2C_M_RD;
342 msg[1].buf = buf;
343 msg[1].len = count;
344
345 loop_until_timeout(timeout, read_time) {
346 status = i2c_transfer(client->adapter, msg, 2);
347 if (status == 2)
348 return count;
349 }
350
351 return -ETIMEDOUT;
352}
353
354static ssize_t at24_eeprom_read_mac(struct at24_data *at24, char *buf,
355 unsigned int offset, size_t count)
356{
357 unsigned long timeout, read_time;
358 struct i2c_client *client;
359 struct i2c_msg msg[2];
360 u8 addrbuf[2];
361 int status;
362
363 client = at24_translate_offset(at24, &offset);
364
365 memset(msg, 0, sizeof(msg));
366 msg[0].addr = client->addr;
367 msg[0].buf = addrbuf;
368 addrbuf[0] = 0x90 + offset;
369 msg[0].len = 1;
370 msg[1].addr = client->addr;
371 msg[1].flags = I2C_M_RD;
372 msg[1].buf = buf;
373 msg[1].len = count;
374
375 loop_until_timeout(timeout, read_time) {
376 status = i2c_transfer(client->adapter, msg, 2);
377 if (status == 2)
378 return count;
379 }
380
381 return -ETIMEDOUT;
382}
383
384/*
385 * Note that if the hardware write-protect pin is pulled high, the whole
386 * chip is normally write protected. But there are plenty of product
387 * variants here, including OTP fuses and partial chip protect.
388 *
389 * We only use page mode writes; the alternative is sloooow. These routines
390 * write at most one page.
391 */
392
393static size_t at24_adjust_write_count(struct at24_data *at24,
394 unsigned int offset, size_t count)
395{
396 unsigned next_page;
397
398 /* write_max is at most a page */
399 if (count > at24->write_max)
400 count = at24->write_max;
401
402 /* Never roll over backwards, to the start of this page */
403 next_page = roundup(offset + 1, at24->chip.page_size);
404 if (offset + count > next_page)
405 count = next_page - offset;
406
407 return count;
408}
409
410static ssize_t at24_eeprom_write_smbus_block(struct at24_data *at24,
411 const char *buf,
412 unsigned int offset, size_t count)
413{
414 unsigned long timeout, write_time;
415 struct i2c_client *client;
416 ssize_t status = 0;
417
418 client = at24_translate_offset(at24, &offset);
419 count = at24_adjust_write_count(at24, offset, count);
420
421 loop_until_timeout(timeout, write_time) {
422 status = i2c_smbus_write_i2c_block_data(client,
423 offset, count, buf);
424 if (status == 0)
425 status = count;
426
427 dev_dbg(&client->dev, "write %zu@%d --> %zd (%ld)\n",
428 count, offset, status, jiffies);
429
430 if (status == count)
431 return count;
432 }
433
434 return -ETIMEDOUT;
435}
436
437static ssize_t at24_eeprom_write_smbus_byte(struct at24_data *at24,
438 const char *buf,
439 unsigned int offset, size_t count)
440{
441 unsigned long timeout, write_time;
442 struct i2c_client *client;
443 ssize_t status = 0;
444
445 client = at24_translate_offset(at24, &offset);
446
447 loop_until_timeout(timeout, write_time) {
448 status = i2c_smbus_write_byte_data(client, offset, buf[0]);
449 if (status == 0)
450 status = count;
451
452 dev_dbg(&client->dev, "write %zu@%d --> %zd (%ld)\n",
453 count, offset, status, jiffies);
454
455 if (status == count)
456 return count;
457 }
458
459 return -ETIMEDOUT;
460}
461
462static ssize_t at24_eeprom_write_i2c(struct at24_data *at24, const char *buf,
463 unsigned int offset, size_t count)
464{
465 unsigned long timeout, write_time;
466 struct i2c_client *client;
467 struct i2c_msg msg;
468 ssize_t status = 0;
469 int i = 0;
470
471 client = at24_translate_offset(at24, &offset);
472 count = at24_adjust_write_count(at24, offset, count);
473
474 msg.addr = client->addr;
475 msg.flags = 0;
476
477 /* msg.buf is u8 and casts will mask the values */
478 msg.buf = at24->writebuf;
479 if (at24->chip.flags & AT24_FLAG_ADDR16)
480 msg.buf[i++] = offset >> 8;
481
482 msg.buf[i++] = offset;
483 memcpy(&msg.buf[i], buf, count);
484 msg.len = i + count;
485
486 loop_until_timeout(timeout, write_time) {
487 status = i2c_transfer(client->adapter, &msg, 1);
488 if (status == 1)
489 status = count;
490
491 dev_dbg(&client->dev, "write %zu@%d --> %zd (%ld)\n",
492 count, offset, status, jiffies);
493
494 if (status == count)
495 return count;
496 }
497
498 return -ETIMEDOUT;
499}
500
501static int at24_read(void *priv, unsigned int off, void *val, size_t count)
502{
503 struct at24_data *at24 = priv;
504 char *buf = val;
505
506 if (unlikely(!count))
507 return count;
508
509 /*
510 * Read data from chip, protecting against concurrent updates
511 * from this host, but not from other I2C masters.
512 */
513 mutex_lock(&at24->lock);
514
515 while (count) {
516 int status;
517
518 status = at24->read_func(at24, buf, off, count);
519 if (status < 0) {
520 mutex_unlock(&at24->lock);
521 return status;
522 }
523 buf += status;
524 off += status;
525 count -= status;
526 }
527
528 mutex_unlock(&at24->lock);
529
530 return 0;
531}
532
533static int at24_write(void *priv, unsigned int off, void *val, size_t count)
534{
535 struct at24_data *at24 = priv;
536 char *buf = val;
537
538 if (unlikely(!count))
539 return -EINVAL;
540
541 /*
542 * Write data to chip, protecting against concurrent updates
543 * from this host, but not from other I2C masters.
544 */
545 mutex_lock(&at24->lock);
546
547 while (count) {
548 int status;
549
550 status = at24->write_func(at24, buf, off, count);
551 if (status < 0) {
552 mutex_unlock(&at24->lock);
553 return status;
554 }
555 buf += status;
556 off += status;
557 count -= status;
558 }
559
560 mutex_unlock(&at24->lock);
561
562 return 0;
563}
564
565#ifdef CONFIG_OF
566static void at24_get_ofdata(struct i2c_client *client,
567 struct at24_platform_data *chip)
568{
569 const __be32 *val;
570 struct device_node *node = client->dev.of_node;
571
572 if (node) {
573 if (of_get_property(node, "read-only", NULL))
574 chip->flags |= AT24_FLAG_READONLY;
575 val = of_get_property(node, "pagesize", NULL);
576 if (val)
577 chip->page_size = be32_to_cpup(val);
578 }
579}
580#else
581static void at24_get_ofdata(struct i2c_client *client,
582 struct at24_platform_data *chip)
583{ }
584#endif /* CONFIG_OF */
585
586static int at24_probe(struct i2c_client *client, const struct i2c_device_id *id)
587{
588 struct at24_platform_data chip;
589 kernel_ulong_t magic = 0;
590 bool writable;
591 int use_smbus = 0;
592 int use_smbus_write = 0;
593 struct at24_data *at24;
594 int err;
595 unsigned i, num_addresses;
596 u8 test_byte;
597
598 if (client->dev.platform_data) {
599 chip = *(struct at24_platform_data *)client->dev.platform_data;
600 } else {
601 if (id) {
602 magic = id->driver_data;
603 } else {
604 const struct acpi_device_id *aid;
605
606 aid = acpi_match_device(at24_acpi_ids, &client->dev);
607 if (aid)
608 magic = aid->driver_data;
609 }
610 if (!magic)
611 return -ENODEV;
612
613 chip.byte_len = BIT(magic & AT24_BITMASK(AT24_SIZE_BYTELEN));
614 magic >>= AT24_SIZE_BYTELEN;
615 chip.flags = magic & AT24_BITMASK(AT24_SIZE_FLAGS);
616 /*
617 * This is slow, but we can't know all eeproms, so we better
618 * play safe. Specifying custom eeprom-types via platform_data
619 * is recommended anyhow.
620 */
621 chip.page_size = 1;
622
623 /* update chipdata if OF is present */
624 at24_get_ofdata(client, &chip);
625
626 chip.setup = NULL;
627 chip.context = NULL;
628 }
629
630 if (!is_power_of_2(chip.byte_len))
631 dev_warn(&client->dev,
632 "byte_len looks suspicious (no power of 2)!\n");
633 if (!chip.page_size) {
634 dev_err(&client->dev, "page_size must not be 0!\n");
635 return -EINVAL;
636 }
637 if (!is_power_of_2(chip.page_size))
638 dev_warn(&client->dev,
639 "page_size looks suspicious (no power of 2)!\n");
640
641 /* Use I2C operations unless we're stuck with SMBus extensions. */
642 if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
643 if (chip.flags & AT24_FLAG_ADDR16)
644 return -EPFNOSUPPORT;
645
646 if (i2c_check_functionality(client->adapter,
647 I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
648 use_smbus = I2C_SMBUS_I2C_BLOCK_DATA;
649 } else if (i2c_check_functionality(client->adapter,
650 I2C_FUNC_SMBUS_READ_WORD_DATA)) {
651 use_smbus = I2C_SMBUS_WORD_DATA;
652 } else if (i2c_check_functionality(client->adapter,
653 I2C_FUNC_SMBUS_READ_BYTE_DATA)) {
654 use_smbus = I2C_SMBUS_BYTE_DATA;
655 } else {
656 return -EPFNOSUPPORT;
657 }
658
659 if (i2c_check_functionality(client->adapter,
660 I2C_FUNC_SMBUS_WRITE_I2C_BLOCK)) {
661 use_smbus_write = I2C_SMBUS_I2C_BLOCK_DATA;
662 } else if (i2c_check_functionality(client->adapter,
663 I2C_FUNC_SMBUS_WRITE_BYTE_DATA)) {
664 use_smbus_write = I2C_SMBUS_BYTE_DATA;
665 chip.page_size = 1;
666 }
667 }
668
669 if (chip.flags & AT24_FLAG_TAKE8ADDR)
670 num_addresses = 8;
671 else
672 num_addresses = DIV_ROUND_UP(chip.byte_len,
673 (chip.flags & AT24_FLAG_ADDR16) ? 65536 : 256);
674
675 at24 = devm_kzalloc(&client->dev, sizeof(struct at24_data) +
676 num_addresses * sizeof(struct i2c_client *), GFP_KERNEL);
677 if (!at24)
678 return -ENOMEM;
679
680 mutex_init(&at24->lock);
681 at24->use_smbus = use_smbus;
682 at24->use_smbus_write = use_smbus_write;
683 at24->chip = chip;
684 at24->num_addresses = num_addresses;
685
686 if ((chip.flags & AT24_FLAG_SERIAL) && (chip.flags & AT24_FLAG_MAC)) {
687 dev_err(&client->dev,
688 "invalid device data - cannot have both AT24_FLAG_SERIAL & AT24_FLAG_MAC.");
689 return -EINVAL;
690 }
691
692 if (chip.flags & AT24_FLAG_SERIAL) {
693 at24->read_func = at24_eeprom_read_serial;
694 } else if (chip.flags & AT24_FLAG_MAC) {
695 at24->read_func = at24_eeprom_read_mac;
696 } else {
697 at24->read_func = at24->use_smbus ? at24_eeprom_read_smbus
698 : at24_eeprom_read_i2c;
699 }
700
701 if (at24->use_smbus) {
702 if (at24->use_smbus_write == I2C_SMBUS_I2C_BLOCK_DATA)
703 at24->write_func = at24_eeprom_write_smbus_block;
704 else
705 at24->write_func = at24_eeprom_write_smbus_byte;
706 } else {
707 at24->write_func = at24_eeprom_write_i2c;
708 }
709
710 writable = !(chip.flags & AT24_FLAG_READONLY);
711 if (writable) {
712 if (!use_smbus || use_smbus_write) {
713
714 unsigned write_max = chip.page_size;
715
716 if (write_max > io_limit)
717 write_max = io_limit;
718 if (use_smbus && write_max > I2C_SMBUS_BLOCK_MAX)
719 write_max = I2C_SMBUS_BLOCK_MAX;
720 at24->write_max = write_max;
721
722 /* buffer (data + address at the beginning) */
723 at24->writebuf = devm_kzalloc(&client->dev,
724 write_max + 2, GFP_KERNEL);
725 if (!at24->writebuf)
726 return -ENOMEM;
727 } else {
728 dev_warn(&client->dev,
729 "cannot write due to controller restrictions.");
730 }
731 }
732
733 at24->client[0] = client;
734
735 /* use dummy devices for multiple-address chips */
736 for (i = 1; i < num_addresses; i++) {
737 at24->client[i] = i2c_new_dummy(client->adapter,
738 client->addr + i);
739 if (!at24->client[i]) {
740 dev_err(&client->dev, "address 0x%02x unavailable\n",
741 client->addr + i);
742 err = -EADDRINUSE;
743 goto err_clients;
744 }
745 }
746
747 i2c_set_clientdata(client, at24);
748
749 /*
750 * Perform a one-byte test read to verify that the
751 * chip is functional.
752 */
753 err = at24_read(at24, 0, &test_byte, 1);
754 if (err) {
755 err = -ENODEV;
756 goto err_clients;
757 }
758
759 at24->nvmem_config.name = dev_name(&client->dev);
760 at24->nvmem_config.dev = &client->dev;
761 at24->nvmem_config.read_only = !writable;
762 at24->nvmem_config.root_only = true;
763 at24->nvmem_config.owner = THIS_MODULE;
764 at24->nvmem_config.compat = true;
765 at24->nvmem_config.base_dev = &client->dev;
766 at24->nvmem_config.reg_read = at24_read;
767 at24->nvmem_config.reg_write = at24_write;
768 at24->nvmem_config.priv = at24;
769 at24->nvmem_config.stride = 4;
770 at24->nvmem_config.word_size = 1;
771 at24->nvmem_config.size = chip.byte_len;
772
773 at24->nvmem = nvmem_register(&at24->nvmem_config);
774
775 if (IS_ERR(at24->nvmem)) {
776 err = PTR_ERR(at24->nvmem);
777 goto err_clients;
778 }
779
780 dev_info(&client->dev, "%u byte %s EEPROM, %s, %u bytes/write\n",
781 chip.byte_len, client->name,
782 writable ? "writable" : "read-only", at24->write_max);
783 if (use_smbus == I2C_SMBUS_WORD_DATA ||
784 use_smbus == I2C_SMBUS_BYTE_DATA) {
785 dev_notice(&client->dev, "Falling back to %s reads, "
786 "performance will suffer\n", use_smbus ==
787 I2C_SMBUS_WORD_DATA ? "word" : "byte");
788 }
789
790 /* export data to kernel code */
791 if (chip.setup)
792 chip.setup(at24->nvmem, chip.context);
793
794 return 0;
795
796err_clients:
797 for (i = 1; i < num_addresses; i++)
798 if (at24->client[i])
799 i2c_unregister_device(at24->client[i]);
800
801 return err;
802}
803
804static int at24_remove(struct i2c_client *client)
805{
806 struct at24_data *at24;
807 int i;
808
809 at24 = i2c_get_clientdata(client);
810
811 nvmem_unregister(at24->nvmem);
812
813 for (i = 1; i < at24->num_addresses; i++)
814 i2c_unregister_device(at24->client[i]);
815
816 return 0;
817}
818
819/*-------------------------------------------------------------------------*/
820
821static struct i2c_driver at24_driver = {
822 .driver = {
823 .name = "at24",
824 .acpi_match_table = ACPI_PTR(at24_acpi_ids),
825 },
826 .probe = at24_probe,
827 .remove = at24_remove,
828 .id_table = at24_ids,
829};
830
831static int __init at24_init(void)
832{
833 if (!io_limit) {
834 pr_err("at24: io_limit must not be 0!\n");
835 return -EINVAL;
836 }
837
838 io_limit = rounddown_pow_of_two(io_limit);
839 return i2c_add_driver(&at24_driver);
840}
841module_init(at24_init);
842
843static void __exit at24_exit(void)
844{
845 i2c_del_driver(&at24_driver);
846}
847module_exit(at24_exit);
848
849MODULE_DESCRIPTION("Driver for most I2C EEPROMs");
850MODULE_AUTHOR("David Brownell and Wolfram Sang");
851MODULE_LICENSE("GPL");