1/*
  2 * Copyright (C) 2015 Phytec Messtechnik GmbH
  3 * Author: Teresa Remmet <t.remmet@phytec.de>
  4 *
  5 * This program is free software; you can redistribute it and/or modify
  6 * it under the terms of the GNU General Public License version 2 as
  7 * published by the Free Software Foundation.
  8 */
  9
 10/ {
 11	model = "Phytec AM335x phyBOARD-WEGA";
 12	compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx";
 13
 14	sound: sound_iface {
 15		compatible = "ti,da830-evm-audio";
 16	};
 17
 18	regulators {
 19		compatible = "simple-bus";
 20
 21		vcc3v3: fixedregulator1 {
 22			compatible = "regulator-fixed";
 23			regulator-name = "vcc3v3";
 24			regulator-min-microvolt = <3300000>;
 25			regulator-max-microvolt = <3300000>;
 26			regulator-boot-on;
 27		};
 28	};
 29};
 30
 31/* Audio */
 32&am33xx_pinmux {
 33	mcasp0_pins: pinmux_mcasp0 {
 34		pinctrl-single,pins = <
 35			AM33XX_IOPAD(0x9AC, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_ahclkx.mcasp0_ahclkx */
 36			AM33XX_IOPAD(0x990, PIN_INPUT_PULLDOWN | MUX_MODE0)  /* mcasp0_aclkx.mcasp0_aclkx */
 37			AM33XX_IOPAD(0x994, PIN_INPUT_PULLDOWN | MUX_MODE0)  /* mcasp0_fsx.mcasp0_fsx */
 38			AM33XX_IOPAD(0x998, PIN_INPUT_PULLDOWN | MUX_MODE0)  /* mcasp0_axr0.mcasp0_axr0 */
 39			AM33XX_IOPAD(0x9A8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_axr1.mcasp0_axr1 */
 40		>;
 41	};
 42};
 43
 44&i2c0 {
 45	tlv320aic3007: tlv320aic3007@18 {
 46		compatible = "ti,tlv320aic3007";
 47		reg = <0x18>;
 48		AVDD-supply = <&vcc3v3>;
 49		IOVDD-supply = <&vcc3v3>;
 50		DRVDD-supply = <&vcc3v3>;
 51		DVDD-supply = <&vdig1_reg>;
 52		status = "okay";
 53	};
 54};
 55
 56&mcasp0 {
 57	pinctrl-names = "default";
 58	pinctrl-0 = <&mcasp0_pins>;
 59	op-mode = <0>; /* DAVINCI_MCASP_IIS_MODE */
 60	tdm-slots = <2>;
 61	serial-dir = <
 62		2 1 0 0 /* # 0: INACTIVE, 1: TX, 2: RX */
 63	>;
 64	tx-num-evt = <16>;
 65	rt-num-evt = <16>;
 66	status = "okay";
 67};
 68
 69&sound {
 70	ti,model = "AM335x-Wega";
 71	ti,audio-codec = <&tlv320aic3007>;
 72	ti,mcasp-controller = <&mcasp0>;
 73	ti,audio-routing =
 74		"Line Out",		"LLOUT",
 75		"Line Out",		"RLOUT",
 76		"LINE1L",		"Line In",
 77		"LINE1R",		"Line In";
 78	clocks = <&mcasp0_fck>;
 79	clock-names = "mclk";
 80	status = "okay";
 81};
 82
 83/* CAN Busses */
 84&am33xx_pinmux {
 85	dcan1_pins: pinmux_dcan1 {
 86		pinctrl-single,pins = <
 87			AM33XX_IOPAD(0x968, PIN_OUTPUT_PULLUP | MUX_MODE2) /* uart0_ctsn.d_can1_tx */
 88			AM33XX_IOPAD(0x96c, PIN_INPUT_PULLUP | MUX_MODE2) /* uart0_rtsn.d_can1_rx */
 89		>;
 90	};
 91};
 92
 93&dcan1 {
 94	pinctrl-names = "default";
 95	pinctrl-0 = <&dcan1_pins>;
 96	status = "okay";
 97};
 98
 99/* Ethernet */
100&am33xx_pinmux {
101	ethernet1_pins: pinmux_ethernet1 {
102		pinctrl-single,pins = <
103			AM33XX_IOPAD(0x840, PIN_OUTPUT | MUX_MODE1)		/* gpmc_a0.mii2_txen */
104			AM33XX_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_a1.mii2_rxdv */
105			AM33XX_IOPAD(0x848, PIN_OUTPUT | MUX_MODE1)		/* gpmc_a2.mii2_txd3 */
106			AM33XX_IOPAD(0x84c, PIN_OUTPUT | MUX_MODE1)		/* gpmc_a3.mii2_txd2 */
107			AM33XX_IOPAD(0x850, PIN_OUTPUT | MUX_MODE1)		/* gpmc_a4.mii2_txd1 */
108			AM33XX_IOPAD(0x854, PIN_OUTPUT | MUX_MODE1)		/* gpmc_a5.mii2_txd0 */
109			AM33XX_IOPAD(0x858, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_a6.mii2_txclk */
110			AM33XX_IOPAD(0x85c, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_a7.mii2_rxclk */
111			AM33XX_IOPAD(0x860, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_a8.mii2_rxd3 */
112			AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_a9.mii2_rxd2 */
113			AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_a10.mii2_rxd1 */
114			AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_a11.mii2_rxd0 */
115			AM33XX_IOPAD(0x874, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_wpn.mii2_rxerr */
116			AM33XX_IOPAD(0x878, PIN_INPUT_PULLDOWN | MUX_MODE1)	/* gpmc_ben1.mii2_col */
117		>;
118	};
119};
120
121&cpsw_emac1 {
122	phy-handle = <&phy1>;
123	phy-mode = "mii";
124	dual_emac_res_vlan = <2>;
125};
126
127&davinci_mdio {
128	phy1: ethernet-phy@1 {
129		reg = <1>;
130	};
131};
132
133&mac {
134	slaves = <2>;
135	pinctrl-names = "default";
136	pinctrl-0 = <&ethernet0_pins &ethernet1_pins>;
137	dual_emac = <1>;
138};
139
140/* MMC */
141&am33xx_pinmux {
142	mmc1_pins: pinmux_mmc1 {
143		pinctrl-single,pins = <
144			AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat3.mmc0_dat3 */
145			AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat2.mmc0_dat2 */
146			AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat1.mmc0_dat1 */
147			AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat0.mmc0_dat0 */
148			AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_clk.mmc0_clk */
149			AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_cmd.mmc0_cmd */
150			AM33XX_IOPAD(0x960, PIN_INPUT_PULLUP | MUX_MODE7)	/* spi0_cs1.mmc0_sdcd */
151		>;
152	};
153};
154
155&mmc1 {
156	vmmc-supply = <&vcc3v3>;
157	bus-width = <4>;
158	pinctrl-names = "default";
159	pinctrl-0 = <&mmc1_pins>;
160	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
161	status = "okay";
162};
163
164/* Power */
165&vdig1_reg {
166	regulator-boot-on;
167	regulator-always-on;
168};
169
170/* UARTs */
171&am33xx_pinmux {
172	uart0_pins: pinmux_uart0 {
173		pinctrl-single,pins = <
174			AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0)    /* uart0_rxd.uart0_rxd */
175			AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */
176		>;
177	};
178
179	uart1_pins: pinmux_uart1_pins {
180		pinctrl-single,pins = <
181			AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart1_rxd.uart1_rxd */
182			AM33XX_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_txd.uart1_txd */
183			AM33XX_IOPAD(0x978, PIN_INPUT | MUX_MODE0)		/* uart1_ctsn.uart1_ctsn */
184			AM33XX_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_rtsn.uart1_rtsn */
185		>;
186	};
187};
188
189&uart0 {
190	pinctrl-names = "default";
191	pinctrl-0 = <&uart0_pins>;
192	status = "okay";
193};
194
195&uart1 {
196	pinctrl-names = "default";
197	pinctrl-0 = <&uart1_pins>;
198	status = "okay";
199};
200
201/* USB */
202&cppi41dma {
203	status = "okay";
204};
205
206&usb_ctrl_mod {
207	status = "okay";
208};
209
210&usb {
211	status = "okay";
212};
213
214&usb0 {
215	status = "okay";
216};
217
218&usb0_phy {
219	status = "okay";
220};
221
222&usb1 {
223	dr_mode = "host";
224	status = "okay";
225};
226
227&usb1_phy {
228	status = "okay";
229};