Loading...
1// SPDX-License-Identifier: GPL-2.0
2/include/ "skeleton.dtsi"
3#include <dt-bindings/input/input.h>
4#include <dt-bindings/gpio/gpio.h>
5
6#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
7
8/ {
9 compatible = "marvell,kirkwood";
10 interrupt-parent = <&intc>;
11
12 cpus {
13 #address-cells = <1>;
14 #size-cells = <0>;
15
16 cpu@0 {
17 device_type = "cpu";
18 compatible = "marvell,feroceon";
19 reg = <0>;
20 clocks = <&core_clk 1>, <&core_clk 3>, <&gate_clk 11>;
21 clock-names = "cpu_clk", "ddrclk", "powersave";
22 };
23 };
24
25 aliases {
26 gpio0 = &gpio0;
27 gpio1 = &gpio1;
28 i2c0 = &i2c0;
29 };
30
31 mbus@f1000000 {
32 compatible = "marvell,kirkwood-mbus", "simple-bus";
33 #address-cells = <2>;
34 #size-cells = <1>;
35 /* If a board file needs to change this ranges it must replace it completely */
36 ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 /* internal-regs */
37 MBUS_ID(0x01, 0x2f) 0 0xf4000000 0x10000 /* nand flash */
38 MBUS_ID(0x03, 0x01) 0 0xf5000000 0x10000 /* crypto sram */
39 >;
40 controller = <&mbusc>;
41 pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256 MiB memory space */
42 pcie-io-aperture = <0xf2000000 0x100000>; /* 1 MiB I/O space */
43
44 nand: nand@12f {
45 #address-cells = <1>;
46 #size-cells = <1>;
47 cle = <0>;
48 ale = <1>;
49 bank-width = <1>;
50 compatible = "marvell,orion-nand";
51 reg = <MBUS_ID(0x01, 0x2f) 0 0x400>;
52 chip-delay = <25>;
53 /* set partition map and/or chip-delay in board dts */
54 clocks = <&gate_clk 7>;
55 pinctrl-0 = <&pmx_nand>;
56 pinctrl-names = "default";
57 status = "disabled";
58 };
59
60 crypto_sram: sa-sram@301 {
61 compatible = "mmio-sram";
62 reg = <MBUS_ID(0x03, 0x01) 0x0 0x800>;
63 clocks = <&gate_clk 17>;
64 #address-cells = <1>;
65 #size-cells = <1>;
66 };
67 };
68
69 ocp@f1000000 {
70 compatible = "simple-bus";
71 ranges = <0x00000000 0xf1000000 0x0100000>;
72 #address-cells = <1>;
73 #size-cells = <1>;
74
75 pinctrl: pin-controller@10000 {
76 /* set compatible property in SoC file */
77 reg = <0x10000 0x20>;
78
79 pmx_ge1: pmx-ge1 {
80 marvell,pins = "mpp20", "mpp21", "mpp22", "mpp23",
81 "mpp24", "mpp25", "mpp26", "mpp27",
82 "mpp30", "mpp31", "mpp32", "mpp33";
83 marvell,function = "ge1";
84 };
85
86 pmx_nand: pmx-nand {
87 marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3",
88 "mpp4", "mpp5", "mpp18", "mpp19";
89 marvell,function = "nand";
90 };
91
92 /*
93 * Default SPI0 pinctrl setting with CSn on mpp0,
94 * overwrite marvell,pins on board level if required.
95 */
96 pmx_spi: pmx-spi {
97 marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3";
98 marvell,function = "spi";
99 };
100
101 pmx_twsi0: pmx-twsi0 {
102 marvell,pins = "mpp8", "mpp9";
103 marvell,function = "twsi0";
104 };
105
106 /*
107 * Default UART pinctrl setting without RTS/CTS,
108 * overwrite marvell,pins on board level if required.
109 */
110 pmx_uart0: pmx-uart0 {
111 marvell,pins = "mpp10", "mpp11";
112 marvell,function = "uart0";
113 };
114
115 pmx_uart1: pmx-uart1 {
116 marvell,pins = "mpp13", "mpp14";
117 marvell,function = "uart1";
118 };
119 };
120
121 core_clk: core-clocks@10030 {
122 compatible = "marvell,kirkwood-core-clock";
123 reg = <0x10030 0x4>;
124 #clock-cells = <1>;
125 };
126
127 spi0: spi@10600 {
128 compatible = "marvell,orion-spi";
129 #address-cells = <1>;
130 #size-cells = <0>;
131 cell-index = <0>;
132 interrupts = <23>;
133 reg = <0x10600 0x28>;
134 clocks = <&gate_clk 7>;
135 pinctrl-0 = <&pmx_spi>;
136 pinctrl-names = "default";
137 status = "disabled";
138 };
139
140 gpio0: gpio@10100 {
141 compatible = "marvell,orion-gpio";
142 #gpio-cells = <2>;
143 gpio-controller;
144 reg = <0x10100 0x40>;
145 ngpios = <32>;
146 interrupt-controller;
147 #interrupt-cells = <2>;
148 interrupts = <35>, <36>, <37>, <38>;
149 clocks = <&gate_clk 7>;
150 };
151
152 gpio1: gpio@10140 {
153 compatible = "marvell,orion-gpio";
154 #gpio-cells = <2>;
155 gpio-controller;
156 reg = <0x10140 0x40>;
157 ngpios = <18>;
158 interrupt-controller;
159 #interrupt-cells = <2>;
160 interrupts = <39>, <40>, <41>;
161 clocks = <&gate_clk 7>;
162 };
163
164 i2c0: i2c@11000 {
165 compatible = "marvell,mv64xxx-i2c";
166 reg = <0x11000 0x20>;
167 #address-cells = <1>;
168 #size-cells = <0>;
169 interrupts = <29>;
170 clock-frequency = <100000>;
171 clocks = <&gate_clk 7>;
172 pinctrl-0 = <&pmx_twsi0>;
173 pinctrl-names = "default";
174 status = "disabled";
175 };
176
177 uart0: serial@12000 {
178 compatible = "ns16550a";
179 reg = <0x12000 0x100>;
180 reg-shift = <2>;
181 interrupts = <33>;
182 clocks = <&gate_clk 7>;
183 pinctrl-0 = <&pmx_uart0>;
184 pinctrl-names = "default";
185 status = "disabled";
186 };
187
188 uart1: serial@12100 {
189 compatible = "ns16550a";
190 reg = <0x12100 0x100>;
191 reg-shift = <2>;
192 interrupts = <34>;
193 clocks = <&gate_clk 7>;
194 pinctrl-0 = <&pmx_uart1>;
195 pinctrl-names = "default";
196 status = "disabled";
197 };
198
199 mbusc: mbus-controller@20000 {
200 compatible = "marvell,mbus-controller";
201 reg = <0x20000 0x80>, <0x1500 0x20>;
202 };
203
204 sysc: system-controller@20000 {
205 compatible = "marvell,orion-system-controller";
206 reg = <0x20000 0x120>;
207 };
208
209 bridge_intc: bridge-interrupt-ctrl@20110 {
210 compatible = "marvell,orion-bridge-intc";
211 interrupt-controller;
212 #interrupt-cells = <1>;
213 reg = <0x20110 0x8>;
214 interrupts = <1>;
215 marvell,#interrupts = <6>;
216 };
217
218 gate_clk: clock-gating-control@2011c {
219 compatible = "marvell,kirkwood-gating-clock";
220 reg = <0x2011c 0x4>;
221 clocks = <&core_clk 0>;
222 #clock-cells = <1>;
223 };
224
225 l2: l2-cache@20128 {
226 compatible = "marvell,kirkwood-cache";
227 reg = <0x20128 0x4>;
228 };
229
230 intc: main-interrupt-ctrl@20200 {
231 compatible = "marvell,orion-intc";
232 interrupt-controller;
233 #interrupt-cells = <1>;
234 reg = <0x20200 0x10>, <0x20210 0x10>;
235 };
236
237 timer: timer@20300 {
238 compatible = "marvell,orion-timer";
239 reg = <0x20300 0x20>;
240 interrupt-parent = <&bridge_intc>;
241 interrupts = <1>, <2>;
242 clocks = <&core_clk 0>;
243 };
244
245 wdt: watchdog-timer@20300 {
246 compatible = "marvell,orion-wdt";
247 reg = <0x20300 0x28>, <0x20108 0x4>;
248 interrupt-parent = <&bridge_intc>;
249 interrupts = <3>;
250 clocks = <&gate_clk 7>;
251 status = "okay";
252 };
253
254 cesa: crypto@30000 {
255 compatible = "marvell,kirkwood-crypto";
256 reg = <0x30000 0x10000>;
257 reg-names = "regs";
258 interrupts = <22>;
259 clocks = <&gate_clk 17>;
260 marvell,crypto-srams = <&crypto_sram>;
261 marvell,crypto-sram-size = <0x800>;
262 status = "okay";
263 };
264
265 usb0: ehci@50000 {
266 compatible = "marvell,orion-ehci";
267 reg = <0x50000 0x1000>;
268 interrupts = <19>;
269 clocks = <&gate_clk 3>;
270 status = "okay";
271 };
272
273 dma0: xor@60800 {
274 compatible = "marvell,orion-xor";
275 reg = <0x60800 0x100
276 0x60A00 0x100>;
277 status = "okay";
278 clocks = <&gate_clk 8>;
279
280 xor00 {
281 interrupts = <5>;
282 dmacap,memcpy;
283 dmacap,xor;
284 };
285 xor01 {
286 interrupts = <6>;
287 dmacap,memcpy;
288 dmacap,xor;
289 dmacap,memset;
290 };
291 };
292
293 dma1: xor@60900 {
294 compatible = "marvell,orion-xor";
295 reg = <0x60900 0x100
296 0x60B00 0x100>;
297 status = "okay";
298 clocks = <&gate_clk 16>;
299
300 xor00 {
301 interrupts = <7>;
302 dmacap,memcpy;
303 dmacap,xor;
304 };
305 xor01 {
306 interrupts = <8>;
307 dmacap,memcpy;
308 dmacap,xor;
309 dmacap,memset;
310 };
311 };
312
313 eth0: ethernet-controller@72000 {
314 compatible = "marvell,kirkwood-eth";
315 #address-cells = <1>;
316 #size-cells = <0>;
317 reg = <0x72000 0x4000>;
318 clocks = <&gate_clk 0>;
319 marvell,tx-checksum-limit = <1600>;
320 status = "disabled";
321
322 eth0port: ethernet0-port@0 {
323 compatible = "marvell,kirkwood-eth-port";
324 reg = <0>;
325 interrupts = <11>;
326 /* overwrite MAC address in bootloader */
327 local-mac-address = [00 00 00 00 00 00];
328 /* set phy-handle property in board file */
329 };
330 };
331
332 mdio: mdio-bus@72004 {
333 compatible = "marvell,orion-mdio";
334 #address-cells = <1>;
335 #size-cells = <0>;
336 reg = <0x72004 0x84>;
337 interrupts = <46>;
338 clocks = <&gate_clk 0>;
339 status = "disabled";
340
341 /* add phy nodes in board file */
342 };
343
344 eth1: ethernet-controller@76000 {
345 compatible = "marvell,kirkwood-eth";
346 #address-cells = <1>;
347 #size-cells = <0>;
348 reg = <0x76000 0x4000>;
349 clocks = <&gate_clk 19>;
350 marvell,tx-checksum-limit = <1600>;
351 pinctrl-0 = <&pmx_ge1>;
352 pinctrl-names = "default";
353 status = "disabled";
354
355 eth1port: ethernet1-port@0 {
356 compatible = "marvell,kirkwood-eth-port";
357 reg = <0>;
358 interrupts = <15>;
359 /* overwrite MAC address in bootloader */
360 local-mac-address = [00 00 00 00 00 00];
361 /* set phy-handle property in board file */
362 };
363 };
364
365 sata_phy0: sata-phy@82000 {
366 compatible = "marvell,mvebu-sata-phy";
367 reg = <0x82000 0x0334>;
368 clocks = <&gate_clk 14>;
369 clock-names = "sata";
370 #phy-cells = <0>;
371 status = "ok";
372 };
373
374 sata_phy1: sata-phy@84000 {
375 compatible = "marvell,mvebu-sata-phy";
376 reg = <0x84000 0x0334>;
377 clocks = <&gate_clk 15>;
378 clock-names = "sata";
379 #phy-cells = <0>;
380 status = "ok";
381 };
382
383 audio0: audio-controller@a0000 {
384 compatible = "marvell,kirkwood-audio";
385 #sound-dai-cells = <0>;
386 reg = <0xa0000 0x2210>;
387 interrupts = <24>;
388 clocks = <&gate_clk 9>;
389 clock-names = "internal";
390 status = "disabled";
391 };
392 };
393};
1/include/ "skeleton.dtsi"
2#include <dt-bindings/input/input.h>
3#include <dt-bindings/gpio/gpio.h>
4
5#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
6
7/ {
8 compatible = "marvell,kirkwood";
9 interrupt-parent = <&intc>;
10
11 cpus {
12 #address-cells = <1>;
13 #size-cells = <0>;
14
15 cpu@0 {
16 device_type = "cpu";
17 compatible = "marvell,feroceon";
18 reg = <0>;
19 clocks = <&core_clk 1>, <&core_clk 3>, <&gate_clk 11>;
20 clock-names = "cpu_clk", "ddrclk", "powersave";
21 };
22 };
23
24 aliases {
25 gpio0 = &gpio0;
26 gpio1 = &gpio1;
27 i2c0 = &i2c0;
28 };
29
30 mbus {
31 compatible = "marvell,kirkwood-mbus", "simple-bus";
32 #address-cells = <2>;
33 #size-cells = <1>;
34 /* If a board file needs to change this ranges it must replace it completely */
35 ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 /* internal-regs */
36 MBUS_ID(0x01, 0x2f) 0 0xf4000000 0x10000 /* nand flash */
37 MBUS_ID(0x03, 0x01) 0 0xf5000000 0x10000 /* crypto sram */
38 >;
39 controller = <&mbusc>;
40 pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256 MiB memory space */
41 pcie-io-aperture = <0xf2000000 0x100000>; /* 1 MiB I/O space */
42
43 crypto@0301 {
44 compatible = "marvell,orion-crypto";
45 reg = <MBUS_ID(0xf0, 0x01) 0x30000 0x10000>,
46 <MBUS_ID(0x03, 0x01) 0 0x800>;
47 reg-names = "regs", "sram";
48 interrupts = <22>;
49 clocks = <&gate_clk 17>;
50 status = "okay";
51 };
52
53 nand: nand@012f {
54 #address-cells = <1>;
55 #size-cells = <1>;
56 cle = <0>;
57 ale = <1>;
58 bank-width = <1>;
59 compatible = "marvell,orion-nand";
60 reg = <MBUS_ID(0x01, 0x2f) 0 0x400>;
61 chip-delay = <25>;
62 /* set partition map and/or chip-delay in board dts */
63 clocks = <&gate_clk 7>;
64 status = "disabled";
65 };
66 };
67
68 ocp@f1000000 {
69 compatible = "simple-bus";
70 ranges = <0x00000000 0xf1000000 0x0100000>;
71 #address-cells = <1>;
72 #size-cells = <1>;
73
74 core_clk: core-clocks@10030 {
75 compatible = "marvell,kirkwood-core-clock";
76 reg = <0x10030 0x4>;
77 #clock-cells = <1>;
78 };
79
80 spi@10600 {
81 compatible = "marvell,orion-spi";
82 #address-cells = <1>;
83 #size-cells = <0>;
84 cell-index = <0>;
85 interrupts = <23>;
86 reg = <0x10600 0x28>;
87 clocks = <&gate_clk 7>;
88 status = "disabled";
89 };
90
91 gpio0: gpio@10100 {
92 compatible = "marvell,orion-gpio";
93 #gpio-cells = <2>;
94 gpio-controller;
95 reg = <0x10100 0x40>;
96 ngpios = <32>;
97 interrupt-controller;
98 #interrupt-cells = <2>;
99 interrupts = <35>, <36>, <37>, <38>;
100 clocks = <&gate_clk 7>;
101 };
102
103 gpio1: gpio@10140 {
104 compatible = "marvell,orion-gpio";
105 #gpio-cells = <2>;
106 gpio-controller;
107 reg = <0x10140 0x40>;
108 ngpios = <18>;
109 interrupt-controller;
110 #interrupt-cells = <2>;
111 interrupts = <39>, <40>, <41>;
112 clocks = <&gate_clk 7>;
113 };
114
115 i2c0: i2c@11000 {
116 compatible = "marvell,mv64xxx-i2c";
117 reg = <0x11000 0x20>;
118 #address-cells = <1>;
119 #size-cells = <0>;
120 interrupts = <29>;
121 clock-frequency = <100000>;
122 clocks = <&gate_clk 7>;
123 status = "disabled";
124 };
125
126 serial@12000 {
127 compatible = "ns16550a";
128 reg = <0x12000 0x100>;
129 reg-shift = <2>;
130 interrupts = <33>;
131 clocks = <&gate_clk 7>;
132 status = "disabled";
133 };
134
135 serial@12100 {
136 compatible = "ns16550a";
137 reg = <0x12100 0x100>;
138 reg-shift = <2>;
139 interrupts = <34>;
140 clocks = <&gate_clk 7>;
141 status = "disabled";
142 };
143
144 mbusc: mbus-controller@20000 {
145 compatible = "marvell,mbus-controller";
146 reg = <0x20000 0x80>, <0x1500 0x20>;
147 };
148
149 system-controller@20000 {
150 compatible = "marvell,orion-system-controller";
151 reg = <0x20000 0x120>;
152 };
153
154 bridge_intc: bridge-interrupt-ctrl@20110 {
155 compatible = "marvell,orion-bridge-intc";
156 interrupt-controller;
157 #interrupt-cells = <1>;
158 reg = <0x20110 0x8>;
159 interrupts = <1>;
160 marvell,#interrupts = <6>;
161 };
162
163 gate_clk: clock-gating-control@2011c {
164 compatible = "marvell,kirkwood-gating-clock";
165 reg = <0x2011c 0x4>;
166 clocks = <&core_clk 0>;
167 #clock-cells = <1>;
168 };
169
170 l2: l2-cache@20128 {
171 compatible = "marvell,kirkwood-cache";
172 reg = <0x20128 0x4>;
173 };
174
175 intc: main-interrupt-ctrl@20200 {
176 compatible = "marvell,orion-intc";
177 interrupt-controller;
178 #interrupt-cells = <1>;
179 reg = <0x20200 0x10>, <0x20210 0x10>;
180 };
181
182 timer: timer@20300 {
183 compatible = "marvell,orion-timer";
184 reg = <0x20300 0x20>;
185 interrupt-parent = <&bridge_intc>;
186 interrupts = <1>, <2>;
187 clocks = <&core_clk 0>;
188 };
189
190 wdt: watchdog-timer@20300 {
191 compatible = "marvell,orion-wdt";
192 reg = <0x20300 0x28>, <0x20108 0x4>;
193 interrupt-parent = <&bridge_intc>;
194 interrupts = <3>;
195 clocks = <&gate_clk 7>;
196 status = "okay";
197 };
198
199 ehci@50000 {
200 compatible = "marvell,orion-ehci";
201 reg = <0x50000 0x1000>;
202 interrupts = <19>;
203 clocks = <&gate_clk 3>;
204 status = "okay";
205 };
206
207 xor@60800 {
208 compatible = "marvell,orion-xor";
209 reg = <0x60800 0x100
210 0x60A00 0x100>;
211 status = "okay";
212 clocks = <&gate_clk 8>;
213
214 xor00 {
215 interrupts = <5>;
216 dmacap,memcpy;
217 dmacap,xor;
218 };
219 xor01 {
220 interrupts = <6>;
221 dmacap,memcpy;
222 dmacap,xor;
223 dmacap,memset;
224 };
225 };
226
227 xor@60900 {
228 compatible = "marvell,orion-xor";
229 reg = <0x60900 0x100
230 0x60B00 0x100>;
231 status = "okay";
232 clocks = <&gate_clk 16>;
233
234 xor00 {
235 interrupts = <7>;
236 dmacap,memcpy;
237 dmacap,xor;
238 };
239 xor01 {
240 interrupts = <8>;
241 dmacap,memcpy;
242 dmacap,xor;
243 dmacap,memset;
244 };
245 };
246
247 eth0: ethernet-controller@72000 {
248 compatible = "marvell,kirkwood-eth";
249 #address-cells = <1>;
250 #size-cells = <0>;
251 reg = <0x72000 0x4000>;
252 clocks = <&gate_clk 0>;
253 marvell,tx-checksum-limit = <1600>;
254 status = "disabled";
255
256 ethernet0-port@0 {
257 compatible = "marvell,kirkwood-eth-port";
258 reg = <0>;
259 interrupts = <11>;
260 /* overwrite MAC address in bootloader */
261 local-mac-address = [00 00 00 00 00 00];
262 /* set phy-handle property in board file */
263 };
264 };
265
266 mdio: mdio-bus@72004 {
267 compatible = "marvell,orion-mdio";
268 #address-cells = <1>;
269 #size-cells = <0>;
270 reg = <0x72004 0x84>;
271 interrupts = <46>;
272 clocks = <&gate_clk 0>;
273 status = "disabled";
274
275 /* add phy nodes in board file */
276 };
277
278 eth1: ethernet-controller@76000 {
279 compatible = "marvell,kirkwood-eth";
280 #address-cells = <1>;
281 #size-cells = <0>;
282 reg = <0x76000 0x4000>;
283 clocks = <&gate_clk 19>;
284 marvell,tx-checksum-limit = <1600>;
285 status = "disabled";
286
287 ethernet1-port@0 {
288 compatible = "marvell,kirkwood-eth-port";
289 reg = <0>;
290 interrupts = <15>;
291 /* overwrite MAC address in bootloader */
292 local-mac-address = [00 00 00 00 00 00];
293 /* set phy-handle property in board file */
294 };
295 };
296
297 sata_phy0: sata-phy@82000 {
298 compatible = "marvell,mvebu-sata-phy";
299 reg = <0x82000 0x0334>;
300 clocks = <&gate_clk 14>;
301 clock-names = "sata";
302 #phy-cells = <0>;
303 status = "ok";
304 };
305
306 sata_phy1: sata-phy@84000 {
307 compatible = "marvell,mvebu-sata-phy";
308 reg = <0x84000 0x0334>;
309 clocks = <&gate_clk 15>;
310 clock-names = "sata";
311 #phy-cells = <0>;
312 status = "ok";
313 };
314
315 audio0: audio-controller@a0000 {
316 compatible = "marvell,kirkwood-audio";
317 reg = <0xa0000 0x2210>;
318 interrupts = <24>;
319 clocks = <&gate_clk 9>;
320 clock-names = "internal";
321 status = "disabled";
322 };
323 };
324};