Loading...
1#
2# PHY Layer Configuration
3#
4
5menuconfig MDIO_DEVICE
6 tristate "MDIO bus device drivers"
7 help
8 MDIO devices and driver infrastructure code.
9
10config MDIO_BUS
11 tristate
12 default m if PHYLIB=m
13 default MDIO_DEVICE
14 help
15 This internal symbol is used for link time dependencies and it
16 reflects whether the mdio_bus/mdio_device code is built as a
17 loadable module or built-in.
18
19if MDIO_BUS
20
21config MDIO_BCM_IPROC
22 tristate "Broadcom iProc MDIO bus controller"
23 depends on ARCH_BCM_IPROC || COMPILE_TEST
24 depends on HAS_IOMEM && OF_MDIO
25 help
26 This module provides a driver for the MDIO busses found in the
27 Broadcom iProc SoC's.
28
29config MDIO_BCM_UNIMAC
30 tristate "Broadcom UniMAC MDIO bus controller"
31 depends on HAS_IOMEM && OF_MDIO
32 help
33 This module provides a driver for the Broadcom UniMAC MDIO busses.
34 This hardware can be found in the Broadcom GENET Ethernet MAC
35 controllers as well as some Broadcom Ethernet switches such as the
36 Starfighter 2 switches.
37
38config MDIO_BITBANG
39 tristate "Bitbanged MDIO buses"
40 help
41 This module implements the MDIO bus protocol in software,
42 for use by low level drivers that export the ability to
43 drive the relevant pins.
44
45 If in doubt, say N.
46
47config MDIO_BUS_MUX
48 tristate
49 depends on OF_MDIO
50 help
51 This module provides a driver framework for MDIO bus
52 multiplexers which connect one of several child MDIO busses
53 to a parent bus. Switching between child busses is done by
54 device specific drivers.
55
56config MDIO_BUS_MUX_BCM_IPROC
57 tristate "Broadcom iProc based MDIO bus multiplexers"
58 depends on OF && OF_MDIO && (ARCH_BCM_IPROC || COMPILE_TEST)
59 select MDIO_BUS_MUX
60 default ARCH_BCM_IPROC
61 help
62 This module provides a driver for MDIO bus multiplexers found in
63 iProc based Broadcom SoCs. This multiplexer connects one of several
64 child MDIO bus to a parent bus. Buses could be internal as well as
65 external and selection logic lies inside the same multiplexer.
66
67config MDIO_BUS_MUX_GPIO
68 tristate "GPIO controlled MDIO bus multiplexers"
69 depends on OF_GPIO && OF_MDIO
70 select MDIO_BUS_MUX
71 help
72 This module provides a driver for MDIO bus multiplexers that
73 are controlled via GPIO lines. The multiplexer connects one of
74 several child MDIO busses to a parent bus. Child bus
75 selection is under the control of GPIO lines.
76
77config MDIO_BUS_MUX_MMIOREG
78 tristate "MMIO device-controlled MDIO bus multiplexers"
79 depends on OF_MDIO && HAS_IOMEM
80 select MDIO_BUS_MUX
81 help
82 This module provides a driver for MDIO bus multiplexers that
83 are controlled via a simple memory-mapped device, like an FPGA.
84 The multiplexer connects one of several child MDIO busses to a
85 parent bus. Child bus selection is under the control of one of
86 the FPGA's registers.
87
88 Currently, only 8/16/32 bits registers are supported.
89
90config MDIO_CAVIUM
91 tristate
92
93config MDIO_GPIO
94 tristate "GPIO lib-based bitbanged MDIO buses"
95 depends on MDIO_BITBANG && GPIOLIB
96 ---help---
97 Supports GPIO lib-based MDIO busses.
98
99 To compile this driver as a module, choose M here: the module
100 will be called mdio-gpio.
101
102config MDIO_HISI_FEMAC
103 tristate "Hisilicon FEMAC MDIO bus controller"
104 depends on HAS_IOMEM && OF_MDIO
105 help
106 This module provides a driver for the MDIO busses found in the
107 Hisilicon SoC that have an Fast Ethernet MAC.
108
109config MDIO_I2C
110 tristate
111 depends on I2C
112 help
113 Support I2C based PHYs. This provides a MDIO bus bridged
114 to I2C to allow PHYs connected in I2C mode to be accessed
115 using the existing infrastructure.
116
117 This is library mode.
118
119config MDIO_MOXART
120 tristate "MOXA ART MDIO interface support"
121 depends on ARCH_MOXART
122 help
123 This driver supports the MDIO interface found in the network
124 interface units of the MOXA ART SoC
125
126config MDIO_OCTEON
127 tristate "Octeon and some ThunderX SOCs MDIO buses"
128 depends on 64BIT
129 depends on HAS_IOMEM && OF_MDIO
130 select MDIO_CAVIUM
131 help
132 This module provides a driver for the Octeon and ThunderX MDIO
133 buses. It is required by the Octeon and ThunderX ethernet device
134 drivers on some systems.
135
136config MDIO_SUN4I
137 tristate "Allwinner sun4i MDIO interface support"
138 depends on ARCH_SUNXI
139 help
140 This driver supports the MDIO interface found in the network
141 interface units of the Allwinner SoC that have an EMAC (A10,
142 A12, A10s, etc.)
143
144config MDIO_THUNDER
145 tristate "ThunderX SOCs MDIO buses"
146 depends on 64BIT
147 depends on PCI
148 select MDIO_CAVIUM
149 help
150 This driver supports the MDIO interfaces found on Cavium
151 ThunderX SoCs when the MDIO bus device appears as a PCI
152 device.
153
154config MDIO_XGENE
155 tristate "APM X-Gene SoC MDIO bus controller"
156 depends on ARCH_XGENE || COMPILE_TEST
157 help
158 This module provides a driver for the MDIO busses found in the
159 APM X-Gene SoC's.
160
161endif
162
163config PHYLINK
164 tristate
165 depends on NETDEVICES
166 select PHYLIB
167 select SWPHY
168 help
169 PHYlink models the link between the PHY and MAC, allowing fixed
170 configuration links, PHYs, and Serdes links with MAC level
171 autonegotiation modes.
172
173menuconfig PHYLIB
174 tristate "PHY Device support and infrastructure"
175 depends on NETDEVICES
176 select MDIO_DEVICE
177 help
178 Ethernet controllers are usually attached to PHY
179 devices. This option provides infrastructure for
180 managing PHY devices.
181
182if PHYLIB
183
184config SWPHY
185 bool
186
187config LED_TRIGGER_PHY
188 bool "Support LED triggers for tracking link state"
189 depends on LEDS_TRIGGERS
190 ---help---
191 Adds support for a set of LED trigger events per-PHY. Link
192 state change will trigger the events, for consumption by an
193 LED class driver. There are triggers for each link speed currently
194 supported by the PHY and also a one common "link" trigger as a
195 logical-or of all the link speed ones.
196 All these triggers are named according to the following pattern:
197 <mii bus id>:<phy>:<speed>
198
199 Where speed is in the form:
200 <Speed in megabits>Mbps OR <Speed in gigabits>Gbps OR link
201 for any speed known to the PHY.
202
203
204comment "MII PHY device drivers"
205
206config SFP
207 tristate "SFP cage support"
208 depends on I2C && PHYLINK
209 select MDIO_I2C
210
211config AMD_PHY
212 tristate "AMD PHYs"
213 ---help---
214 Currently supports the am79c874
215
216config AQUANTIA_PHY
217 tristate "Aquantia PHYs"
218 ---help---
219 Currently supports the Aquantia AQ1202, AQ2104, AQR105, AQR405
220
221config AT803X_PHY
222 tristate "AT803X PHYs"
223 ---help---
224 Currently supports the AT8030 and AT8035 model
225
226config BCM63XX_PHY
227 tristate "Broadcom 63xx SOCs internal PHY"
228 depends on BCM63XX
229 select BCM_NET_PHYLIB
230 ---help---
231 Currently supports the 6348 and 6358 PHYs.
232
233config BCM7XXX_PHY
234 tristate "Broadcom 7xxx SOCs internal PHYs"
235 select BCM_NET_PHYLIB
236 ---help---
237 Currently supports the BCM7366, BCM7439, BCM7445, and
238 40nm and 65nm generation of BCM7xxx Set Top Box SoCs.
239
240config BCM87XX_PHY
241 tristate "Broadcom BCM8706 and BCM8727 PHYs"
242 help
243 Currently supports the BCM8706 and BCM8727 10G Ethernet PHYs.
244
245config BCM_CYGNUS_PHY
246 tristate "Broadcom Cygnus SoC internal PHY"
247 depends on ARCH_BCM_CYGNUS || COMPILE_TEST
248 depends on MDIO_BCM_IPROC
249 select BCM_NET_PHYLIB
250 ---help---
251 This PHY driver is for the 1G internal PHYs of the Broadcom
252 Cygnus Family SoC.
253
254 Currently supports internal PHY's used in the BCM11300,
255 BCM11320, BCM11350, BCM11360, BCM58300, BCM58302,
256 BCM58303 & BCM58305 Broadcom Cygnus SoCs.
257
258config BCM_NET_PHYLIB
259 tristate
260
261config BROADCOM_PHY
262 tristate "Broadcom PHYs"
263 select BCM_NET_PHYLIB
264 ---help---
265 Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464,
266 BCM5481, BCM54810 and BCM5482 PHYs.
267
268config CICADA_PHY
269 tristate "Cicada PHYs"
270 ---help---
271 Currently supports the cis8204
272
273config CORTINA_PHY
274 tristate "Cortina EDC CDR 10G Ethernet PHY"
275 ---help---
276 Currently supports the CS4340 phy.
277
278config DAVICOM_PHY
279 tristate "Davicom PHYs"
280 ---help---
281 Currently supports dm9161e and dm9131
282
283config DP83822_PHY
284 tristate "Texas Instruments DP83822 PHY"
285 ---help---
286 Supports the DP83822 PHY.
287
288config DP83848_PHY
289 tristate "Texas Instruments DP83848 PHY"
290 ---help---
291 Supports the DP83848 PHY.
292
293config DP83867_PHY
294 tristate "Texas Instruments DP83867 Gigabit PHY"
295 ---help---
296 Currently supports the DP83867 PHY.
297
298config FIXED_PHY
299 tristate "MDIO Bus/PHY emulation with fixed speed/link PHYs"
300 depends on PHYLIB
301 select SWPHY
302 ---help---
303 Adds the platform "fixed" MDIO Bus to cover the boards that use
304 PHYs that are not connected to the real MDIO bus.
305
306 Currently tested with mpc866ads and mpc8349e-mitx.
307
308config ICPLUS_PHY
309 tristate "ICPlus PHYs"
310 ---help---
311 Currently supports the IP175C and IP1001 PHYs.
312
313config INTEL_XWAY_PHY
314 tristate "Intel XWAY PHYs"
315 ---help---
316 Supports the Intel XWAY (former Lantiq) 11G and 22E PHYs.
317 These PHYs are marked as standalone chips under the names
318 PEF 7061, PEF 7071 and PEF 7072 or integrated into the Intel
319 SoCs xRX200, xRX300, xRX330, xRX350 and xRX550.
320
321config LSI_ET1011C_PHY
322 tristate "LSI ET1011C PHY"
323 ---help---
324 Supports the LSI ET1011C PHY.
325
326config LXT_PHY
327 tristate "Intel LXT PHYs"
328 ---help---
329 Currently supports the lxt970, lxt971
330
331config MARVELL_PHY
332 tristate "Marvell PHYs"
333 ---help---
334 Currently has a driver for the 88E1011S
335
336config MARVELL_10G_PHY
337 tristate "Marvell Alaska 10Gbit PHYs"
338 ---help---
339 Support for the Marvell Alaska MV88X3310 and compatible PHYs.
340
341config MESON_GXL_PHY
342 tristate "Amlogic Meson GXL Internal PHY"
343 depends on ARCH_MESON || COMPILE_TEST
344 ---help---
345 Currently has a driver for the Amlogic Meson GXL Internal PHY
346
347config MICREL_PHY
348 tristate "Micrel PHYs"
349 ---help---
350 Supports the KSZ9021, VSC8201, KS8001 PHYs.
351
352config MICROCHIP_PHY
353 tristate "Microchip PHYs"
354 help
355 Supports the LAN88XX PHYs.
356
357config MICROSEMI_PHY
358 tristate "Microsemi PHYs"
359 ---help---
360 Currently supports VSC8530, VSC8531, VSC8540 and VSC8541 PHYs
361
362config NATIONAL_PHY
363 tristate "National Semiconductor PHYs"
364 ---help---
365 Currently supports the DP83865 PHY.
366
367config QSEMI_PHY
368 tristate "Quality Semiconductor PHYs"
369 ---help---
370 Currently supports the qs6612
371
372config REALTEK_PHY
373 tristate "Realtek PHYs"
374 ---help---
375 Supports the Realtek 821x PHY.
376
377config RENESAS_PHY
378 tristate "Driver for Renesas PHYs"
379 ---help---
380 Supports the Renesas PHYs uPD60620 and uPD60620A.
381
382config ROCKCHIP_PHY
383 tristate "Driver for Rockchip Ethernet PHYs"
384 ---help---
385 Currently supports the integrated Ethernet PHY.
386
387config SMSC_PHY
388 tristate "SMSC PHYs"
389 ---help---
390 Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs
391
392config STE10XP
393 tristate "STMicroelectronics STe10Xp PHYs"
394 ---help---
395 This is the driver for the STe100p and STe101p PHYs.
396
397config TERANETICS_PHY
398 tristate "Teranetics PHYs"
399 ---help---
400 Currently supports the Teranetics TN2020
401
402config VITESSE_PHY
403 tristate "Vitesse PHYs"
404 ---help---
405 Currently supports the vsc8244
406
407config XILINX_GMII2RGMII
408 tristate "Xilinx GMII2RGMII converter driver"
409 ---help---
410 This driver support xilinx GMII to RGMII IP core it provides
411 the Reduced Gigabit Media Independent Interface(RGMII) between
412 Ethernet physical media devices and the Gigabit Ethernet controller.
413
414endif # PHYLIB
415
416config MICREL_KS8995MA
417 tristate "Micrel KS8995MA 5-ports 10/100 managed Ethernet switch"
418 depends on SPI
1#
2# PHY Layer Configuration
3#
4
5menuconfig PHYLIB
6 tristate "PHY Device support and infrastructure"
7 depends on !S390
8 depends on NETDEVICES
9 help
10 Ethernet controllers are usually attached to PHY
11 devices. This option provides infrastructure for
12 managing PHY devices.
13
14if PHYLIB
15
16comment "MII PHY device drivers"
17
18config MARVELL_PHY
19 tristate "Drivers for Marvell PHYs"
20 ---help---
21 Currently has a driver for the 88E1011S
22
23config DAVICOM_PHY
24 tristate "Drivers for Davicom PHYs"
25 ---help---
26 Currently supports dm9161e and dm9131
27
28config QSEMI_PHY
29 tristate "Drivers for Quality Semiconductor PHYs"
30 ---help---
31 Currently supports the qs6612
32
33config LXT_PHY
34 tristate "Drivers for the Intel LXT PHYs"
35 ---help---
36 Currently supports the lxt970, lxt971
37
38config CICADA_PHY
39 tristate "Drivers for the Cicada PHYs"
40 ---help---
41 Currently supports the cis8204
42
43config VITESSE_PHY
44 tristate "Drivers for the Vitesse PHYs"
45 ---help---
46 Currently supports the vsc8244
47
48config SMSC_PHY
49 tristate "Drivers for SMSC PHYs"
50 ---help---
51 Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs
52
53config BROADCOM_PHY
54 tristate "Drivers for Broadcom PHYs"
55 ---help---
56 Currently supports the BCM5411, BCM5421, BCM5461, BCM5464, BCM5481
57 and BCM5482 PHYs.
58
59config BCM63XX_PHY
60 tristate "Drivers for Broadcom 63xx SOCs internal PHY"
61 depends on BCM63XX
62 ---help---
63 Currently supports the 6348 and 6358 PHYs.
64
65config ICPLUS_PHY
66 tristate "Drivers for ICPlus PHYs"
67 ---help---
68 Currently supports the IP175C and IP1001 PHYs.
69
70config REALTEK_PHY
71 tristate "Drivers for Realtek PHYs"
72 ---help---
73 Supports the Realtek 821x PHY.
74
75config NATIONAL_PHY
76 tristate "Drivers for National Semiconductor PHYs"
77 ---help---
78 Currently supports the DP83865 PHY.
79
80config STE10XP
81 tristate "Driver for STMicroelectronics STe10Xp PHYs"
82 ---help---
83 This is the driver for the STe100p and STe101p PHYs.
84
85config LSI_ET1011C_PHY
86 tristate "Driver for LSI ET1011C PHY"
87 ---help---
88 Supports the LSI ET1011C PHY.
89
90config MICREL_PHY
91 tristate "Driver for Micrel PHYs"
92 ---help---
93 Supports the KSZ9021, VSC8201, KS8001 PHYs.
94
95config FIXED_PHY
96 bool "Driver for MDIO Bus/PHY emulation with fixed speed/link PHYs"
97 depends on PHYLIB=y
98 ---help---
99 Adds the platform "fixed" MDIO Bus to cover the boards that use
100 PHYs that are not connected to the real MDIO bus.
101
102 Currently tested with mpc866ads and mpc8349e-mitx.
103
104config MDIO_BITBANG
105 tristate "Support for bitbanged MDIO buses"
106 help
107 This module implements the MDIO bus protocol in software,
108 for use by low level drivers that export the ability to
109 drive the relevant pins.
110
111 If in doubt, say N.
112
113config MDIO_GPIO
114 tristate "Support for GPIO lib-based bitbanged MDIO buses"
115 depends on MDIO_BITBANG && GENERIC_GPIO
116 ---help---
117 Supports GPIO lib-based MDIO busses.
118
119 To compile this driver as a module, choose M here: the module
120 will be called mdio-gpio.
121
122config MDIO_OCTEON
123 tristate "Support for MDIO buses on Octeon SOCs"
124 depends on CPU_CAVIUM_OCTEON
125 default y
126 help
127
128 This module provides a driver for the Octeon MDIO busses.
129 It is required by the Octeon Ethernet device drivers.
130
131 If in doubt, say Y.
132
133endif # PHYLIB