Loading...
1/*
2 * MPC5121E ADS Device Tree Source
3 *
4 * Copyright 2007-2008 Freescale Semiconductor Inc.
5 *
6 * This program is free software; you can redistribute it and/or modify it
7 * under the terms of the GNU General Public License as published by the
8 * Free Software Foundation; either version 2 of the License, or (at your
9 * option) any later version.
10 */
11
12#include "mpc5121.dtsi"
13
14/ {
15 model = "mpc5121ads";
16 compatible = "fsl,mpc5121ads", "fsl,mpc5121";
17
18 nfc@40000000 {
19 /*
20 * ADS has two Hynix 512MB Nand flash chips in a single
21 * stacked package.
22 */
23 chips = <2>;
24
25 nand@0 {
26 label = "nand";
27 reg = <0x00000000 0x40000000>; /* 512MB + 512MB */
28 };
29 };
30
31 localbus@80000020 {
32 ranges = <0x0 0x0 0xfc000000 0x04000000
33 0x2 0x0 0x82000000 0x00008000>;
34
35 flash@0,0 {
36 compatible = "cfi-flash";
37 reg = <0 0x0 0x4000000>;
38 #address-cells = <1>;
39 #size-cells = <1>;
40 bank-width = <4>;
41 device-width = <2>;
42
43 protected@0 {
44 label = "protected";
45 reg = <0x00000000 0x00040000>; // first sector is protected
46 read-only;
47 };
48 filesystem@40000 {
49 label = "filesystem";
50 reg = <0x00040000 0x03c00000>; // 60M for filesystem
51 };
52 kernel@3c40000 {
53 label = "kernel";
54 reg = <0x03c40000 0x00280000>; // 2.5M for kernel
55 };
56 device-tree@3ec0000 {
57 label = "device-tree";
58 reg = <0x03ec0000 0x00040000>; // one sector for device tree
59 };
60 u-boot@3f00000 {
61 label = "u-boot";
62 reg = <0x03f00000 0x00100000>; // 1M for u-boot
63 read-only;
64 };
65 };
66
67 board-control@2,0 {
68 compatible = "fsl,mpc5121ads-cpld";
69 reg = <0x2 0x0 0x8000>;
70 };
71
72 cpld_pic: pic@2,a {
73 compatible = "fsl,mpc5121ads-cpld-pic";
74 interrupt-controller;
75 #interrupt-cells = <2>;
76 reg = <0x2 0xa 0x5>;
77 /* irq routing:
78 * all irqs but touch screen are routed to irq0 (ipic 48)
79 * touch screen is statically routed to irq1 (ipic 17)
80 * so don't use it here
81 */
82 interrupts = <48 0x8>;
83 };
84 };
85
86 soc@80000000 {
87
88 i2c@1700 {
89 fsl,preserve-clocking;
90
91 hwmon@4a {
92 compatible = "adi,ad7414";
93 reg = <0x4a>;
94 };
95
96 eeprom@50 {
97 compatible = "atmel,24c32";
98 reg = <0x50>;
99 };
100
101 rtc@68 {
102 compatible = "st,m41t62";
103 reg = <0x68>;
104 };
105 };
106
107 eth0: ethernet@2800 {
108 phy-handle = <&phy0>;
109 };
110
111 can@2300 {
112 status = "disabled";
113 };
114
115 can@2380 {
116 status = "disabled";
117 };
118
119 viu@2400 {
120 status = "disabled";
121 };
122
123 mdio@2800 {
124 phy0: ethernet-phy@0 {
125 reg = <1>;
126 };
127 };
128
129 /* mpc5121ads only uses USB0 */
130 usb@3000 {
131 status = "disabled";
132 };
133
134 /* USB0 using internal UTMI PHY */
135 usb@4000 {
136 dr_mode = "host";
137 fsl,invert-drvvbus;
138 fsl,invert-pwr-fault;
139 };
140
141 /* PSC3 serial port A aka ttyPSC0 */
142 psc@11300 {
143 compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
144 };
145
146 /* PSC4 serial port B aka ttyPSC1 */
147 psc@11400 {
148 compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
149 };
150
151 /* PSC5 in ac97 mode */
152 ac97: psc@11500 {
153 compatible = "fsl,mpc5121-psc-ac97", "fsl,mpc5121-psc";
154 fsl,mode = "ac97-slave";
155 fsl,rx-fifo-size = <384>;
156 fsl,tx-fifo-size = <384>;
157 };
158 };
159
160 pci: pci@80008500 {
161 interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
162 interrupt-map = <
163 /* IDSEL 0x15 - Slot 1 PCI */
164 0xa800 0x0 0x0 0x1 &cpld_pic 0x0 0x8
165 0xa800 0x0 0x0 0x2 &cpld_pic 0x1 0x8
166 0xa800 0x0 0x0 0x3 &cpld_pic 0x2 0x8
167 0xa800 0x0 0x0 0x4 &cpld_pic 0x3 0x8
168
169 /* IDSEL 0x16 - Slot 2 MiniPCI */
170 0xb000 0x0 0x0 0x1 &cpld_pic 0x4 0x8
171 0xb000 0x0 0x0 0x2 &cpld_pic 0x5 0x8
172
173 /* IDSEL 0x17 - Slot 3 MiniPCI */
174 0xb800 0x0 0x0 0x1 &cpld_pic 0x6 0x8
175 0xb800 0x0 0x0 0x2 &cpld_pic 0x7 0x8
176 >;
177 };
178};
1/*
2 * MPC5121E ADS Device Tree Source
3 *
4 * Copyright 2007,2008 Freescale Semiconductor Inc.
5 *
6 * This program is free software; you can redistribute it and/or modify it
7 * under the terms of the GNU General Public License as published by the
8 * Free Software Foundation; either version 2 of the License, or (at your
9 * option) any later version.
10 */
11
12/dts-v1/;
13
14/ {
15 model = "mpc5121ads";
16 compatible = "fsl,mpc5121ads";
17 #address-cells = <1>;
18 #size-cells = <1>;
19
20 aliases {
21 pci = &pci;
22 };
23
24 cpus {
25 #address-cells = <1>;
26 #size-cells = <0>;
27
28 PowerPC,5121@0 {
29 device_type = "cpu";
30 reg = <0>;
31 d-cache-line-size = <0x20>; // 32 bytes
32 i-cache-line-size = <0x20>; // 32 bytes
33 d-cache-size = <0x8000>; // L1, 32K
34 i-cache-size = <0x8000>; // L1, 32K
35 timebase-frequency = <49500000>;// 49.5 MHz (csb/4)
36 bus-frequency = <198000000>; // 198 MHz csb bus
37 clock-frequency = <396000000>; // 396 MHz ppc core
38 };
39 };
40
41 memory {
42 device_type = "memory";
43 reg = <0x00000000 0x10000000>; // 256MB at 0
44 };
45
46 mbx@20000000 {
47 compatible = "fsl,mpc5121-mbx";
48 reg = <0x20000000 0x4000>;
49 interrupts = <66 0x8>;
50 interrupt-parent = < &ipic >;
51 };
52
53 sram@30000000 {
54 compatible = "fsl,mpc5121-sram";
55 reg = <0x30000000 0x20000>; // 128K at 0x30000000
56 };
57
58 nfc@40000000 {
59 compatible = "fsl,mpc5121-nfc";
60 reg = <0x40000000 0x100000>; // 1M at 0x40000000
61 interrupts = <6 8>;
62 interrupt-parent = < &ipic >;
63 #address-cells = <1>;
64 #size-cells = <1>;
65 // ADS has two Hynix 512MB Nand flash chips in a single
66 // stacked package.
67 chips = <2>;
68 nand@0 {
69 label = "nand";
70 reg = <0x00000000 0x40000000>; // 512MB + 512MB
71 };
72 };
73
74 localbus@80000020 {
75 compatible = "fsl,mpc5121-localbus";
76 #address-cells = <2>;
77 #size-cells = <1>;
78 reg = <0x80000020 0x40>;
79
80 ranges = <0x0 0x0 0xfc000000 0x04000000
81 0x2 0x0 0x82000000 0x00008000>;
82
83 flash@0,0 {
84 compatible = "cfi-flash";
85 reg = <0 0x0 0x4000000>;
86 #address-cells = <1>;
87 #size-cells = <1>;
88 bank-width = <4>;
89 device-width = <2>;
90 protected@0 {
91 label = "protected";
92 reg = <0x00000000 0x00040000>; // first sector is protected
93 read-only;
94 };
95 filesystem@40000 {
96 label = "filesystem";
97 reg = <0x00040000 0x03c00000>; // 60M for filesystem
98 };
99 kernel@3c40000 {
100 label = "kernel";
101 reg = <0x03c40000 0x00280000>; // 2.5M for kernel
102 };
103 device-tree@3ec0000 {
104 label = "device-tree";
105 reg = <0x03ec0000 0x00040000>; // one sector for device tree
106 };
107 u-boot@3f00000 {
108 label = "u-boot";
109 reg = <0x03f00000 0x00100000>; // 1M for u-boot
110 read-only;
111 };
112 };
113
114 board-control@2,0 {
115 compatible = "fsl,mpc5121ads-cpld";
116 reg = <0x2 0x0 0x8000>;
117 };
118
119 cpld_pic: pic@2,a {
120 compatible = "fsl,mpc5121ads-cpld-pic";
121 interrupt-controller;
122 #interrupt-cells = <2>;
123 reg = <0x2 0xa 0x5>;
124 interrupt-parent = < &ipic >;
125 // irq routing
126 // all irqs but touch screen are routed to irq0 (ipic 48)
127 // touch screen is statically routed to irq1 (ipic 17)
128 // so don't use it here
129 interrupts = <48 0x8>;
130 };
131 };
132
133 soc@80000000 {
134 compatible = "fsl,mpc5121-immr";
135 #address-cells = <1>;
136 #size-cells = <1>;
137 #interrupt-cells = <2>;
138 ranges = <0x0 0x80000000 0x400000>;
139 reg = <0x80000000 0x400000>;
140 bus-frequency = <66000000>; // 66 MHz ips bus
141
142
143 // IPIC
144 // interrupts cell = <intr #, sense>
145 // sense values match linux IORESOURCE_IRQ_* defines:
146 // sense == 8: Level, low assertion
147 // sense == 2: Edge, high-to-low change
148 //
149 ipic: interrupt-controller@c00 {
150 compatible = "fsl,mpc5121-ipic", "fsl,ipic";
151 interrupt-controller;
152 #address-cells = <0>;
153 #interrupt-cells = <2>;
154 reg = <0xc00 0x100>;
155 };
156
157 rtc@a00 { // Real time clock
158 compatible = "fsl,mpc5121-rtc";
159 reg = <0xa00 0x100>;
160 interrupts = <79 0x8 80 0x8>;
161 interrupt-parent = < &ipic >;
162 };
163
164 reset@e00 { // Reset module
165 compatible = "fsl,mpc5121-reset";
166 reg = <0xe00 0x100>;
167 };
168
169 clock@f00 { // Clock control
170 compatible = "fsl,mpc5121-clock";
171 reg = <0xf00 0x100>;
172 };
173
174 pmc@1000{ //Power Management Controller
175 compatible = "fsl,mpc5121-pmc";
176 reg = <0x1000 0x100>;
177 interrupts = <83 0x2>;
178 interrupt-parent = < &ipic >;
179 };
180
181 gpio@1100 {
182 compatible = "fsl,mpc5121-gpio";
183 reg = <0x1100 0x100>;
184 interrupts = <78 0x8>;
185 interrupt-parent = < &ipic >;
186 };
187
188 can@1300 {
189 compatible = "fsl,mpc5121-mscan";
190 interrupts = <12 0x8>;
191 interrupt-parent = < &ipic >;
192 reg = <0x1300 0x80>;
193 };
194
195 can@1380 {
196 compatible = "fsl,mpc5121-mscan";
197 interrupts = <13 0x8>;
198 interrupt-parent = < &ipic >;
199 reg = <0x1380 0x80>;
200 };
201
202 i2c@1700 {
203 #address-cells = <1>;
204 #size-cells = <0>;
205 compatible = "fsl,mpc5121-i2c", "fsl-i2c";
206 reg = <0x1700 0x20>;
207 interrupts = <9 0x8>;
208 interrupt-parent = < &ipic >;
209 fsl,preserve-clocking;
210
211 hwmon@4a {
212 compatible = "adi,ad7414";
213 reg = <0x4a>;
214 };
215
216 eeprom@50 {
217 compatible = "at,24c32";
218 reg = <0x50>;
219 };
220
221 rtc@68 {
222 compatible = "stm,m41t62";
223 reg = <0x68>;
224 };
225 };
226
227 i2c@1720 {
228 #address-cells = <1>;
229 #size-cells = <0>;
230 compatible = "fsl,mpc5121-i2c", "fsl-i2c";
231 reg = <0x1720 0x20>;
232 interrupts = <10 0x8>;
233 interrupt-parent = < &ipic >;
234 };
235
236 i2c@1740 {
237 #address-cells = <1>;
238 #size-cells = <0>;
239 compatible = "fsl,mpc5121-i2c", "fsl-i2c";
240 reg = <0x1740 0x20>;
241 interrupts = <11 0x8>;
242 interrupt-parent = < &ipic >;
243 };
244
245 i2ccontrol@1760 {
246 compatible = "fsl,mpc5121-i2c-ctrl";
247 reg = <0x1760 0x8>;
248 };
249
250 axe@2000 {
251 compatible = "fsl,mpc5121-axe";
252 reg = <0x2000 0x100>;
253 interrupts = <42 0x8>;
254 interrupt-parent = < &ipic >;
255 };
256
257 display@2100 {
258 compatible = "fsl,mpc5121-diu";
259 reg = <0x2100 0x100>;
260 interrupts = <64 0x8>;
261 interrupt-parent = < &ipic >;
262 };
263
264 mdio@2800 {
265 compatible = "fsl,mpc5121-fec-mdio";
266 reg = <0x2800 0x800>;
267 #address-cells = <1>;
268 #size-cells = <0>;
269 phy: ethernet-phy@0 {
270 reg = <1>;
271 device_type = "ethernet-phy";
272 };
273 };
274
275 ethernet@2800 {
276 device_type = "network";
277 compatible = "fsl,mpc5121-fec";
278 reg = <0x2800 0x800>;
279 local-mac-address = [ 00 00 00 00 00 00 ];
280 interrupts = <4 0x8>;
281 interrupt-parent = < &ipic >;
282 phy-handle = < &phy >;
283 fsl,align-tx-packets = <4>;
284 };
285
286 // 5121e has two dr usb modules
287 // mpc5121_ads only uses USB0
288
289 // USB1 using external ULPI PHY
290 //usb@3000 {
291 // compatible = "fsl,mpc5121-usb2-dr";
292 // reg = <0x3000 0x1000>;
293 // #address-cells = <1>;
294 // #size-cells = <0>;
295 // interrupt-parent = < &ipic >;
296 // interrupts = <43 0x8>;
297 // dr_mode = "otg";
298 // phy_type = "ulpi";
299 //};
300
301 // USB0 using internal UTMI PHY
302 usb@4000 {
303 compatible = "fsl,mpc5121-usb2-dr";
304 reg = <0x4000 0x1000>;
305 #address-cells = <1>;
306 #size-cells = <0>;
307 interrupt-parent = < &ipic >;
308 interrupts = <44 0x8>;
309 dr_mode = "otg";
310 phy_type = "utmi_wide";
311 fsl,invert-drvvbus;
312 fsl,invert-pwr-fault;
313 };
314
315 // IO control
316 ioctl@a000 {
317 compatible = "fsl,mpc5121-ioctl";
318 reg = <0xA000 0x1000>;
319 };
320
321 pata@10200 {
322 compatible = "fsl,mpc5121-pata";
323 reg = <0x10200 0x100>;
324 interrupts = <5 0x8>;
325 interrupt-parent = < &ipic >;
326 };
327
328 // 512x PSCs are not 52xx PSC compatible
329 // PSC3 serial port A aka ttyPSC0
330 serial@11300 {
331 device_type = "serial";
332 compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
333 // Logical port assignment needed until driver
334 // learns to use aliases
335 port-number = <0>;
336 cell-index = <3>;
337 reg = <0x11300 0x100>;
338 interrupts = <40 0x8>;
339 interrupt-parent = < &ipic >;
340 rx-fifo-size = <16>;
341 tx-fifo-size = <16>;
342 };
343
344 // PSC4 serial port B aka ttyPSC1
345 serial@11400 {
346 device_type = "serial";
347 compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc";
348 // Logical port assignment needed until driver
349 // learns to use aliases
350 port-number = <1>;
351 cell-index = <4>;
352 reg = <0x11400 0x100>;
353 interrupts = <40 0x8>;
354 interrupt-parent = < &ipic >;
355 rx-fifo-size = <16>;
356 tx-fifo-size = <16>;
357 };
358
359 // PSC5 in ac97 mode
360 ac97@11500 {
361 compatible = "fsl,mpc5121-psc-ac97", "fsl,mpc5121-psc";
362 cell-index = <5>;
363 reg = <0x11500 0x100>;
364 interrupts = <40 0x8>;
365 interrupt-parent = < &ipic >;
366 fsl,mode = "ac97-slave";
367 rx-fifo-size = <384>;
368 tx-fifo-size = <384>;
369 };
370
371 pscfifo@11f00 {
372 compatible = "fsl,mpc5121-psc-fifo";
373 reg = <0x11f00 0x100>;
374 interrupts = <40 0x8>;
375 interrupt-parent = < &ipic >;
376 };
377
378 dma@14000 {
379 compatible = "fsl,mpc5121-dma";
380 reg = <0x14000 0x1800>;
381 interrupts = <65 0x8>;
382 interrupt-parent = < &ipic >;
383 };
384
385 };
386
387 pci: pci@80008500 {
388 interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
389 interrupt-map = <
390 // IDSEL 0x15 - Slot 1 PCI
391 0xa800 0x0 0x0 0x1 &cpld_pic 0x0 0x8
392 0xa800 0x0 0x0 0x2 &cpld_pic 0x1 0x8
393 0xa800 0x0 0x0 0x3 &cpld_pic 0x2 0x8
394 0xa800 0x0 0x0 0x4 &cpld_pic 0x3 0x8
395
396 // IDSEL 0x16 - Slot 2 MiniPCI
397 0xb000 0x0 0x0 0x1 &cpld_pic 0x4 0x8
398 0xb000 0x0 0x0 0x2 &cpld_pic 0x5 0x8
399
400 // IDSEL 0x17 - Slot 3 MiniPCI
401 0xb800 0x0 0x0 0x1 &cpld_pic 0x6 0x8
402 0xb800 0x0 0x0 0x2 &cpld_pic 0x7 0x8
403 >;
404 interrupt-parent = < &ipic >;
405 interrupts = <1 0x8>;
406 bus-range = <0 0>;
407 ranges = <0x42000000 0x0 0xa0000000 0xa0000000 0x0 0x10000000
408 0x02000000 0x0 0xb0000000 0xb0000000 0x0 0x10000000
409 0x01000000 0x0 0x00000000 0x84000000 0x0 0x01000000>;
410 clock-frequency = <0>;
411 #interrupt-cells = <1>;
412 #size-cells = <2>;
413 #address-cells = <3>;
414 reg = <0x80008500 0x100 /* internal registers */
415 0x80008300 0x8>; /* config space access registers */
416 compatible = "fsl,mpc5121-pci";
417 device_type = "pci";
418 };
419};