Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 | /* * cardbus.c -- 16-bit PCMCIA core support * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. * * The initial developer of the original code is David A. Hinds * <dahinds@users.sourceforge.net>. Portions created by David A. Hinds * are Copyright (C) 1999 David A. Hinds. All Rights Reserved. * * (C) 1999 David A. Hinds */ /* * Cardbus handling has been re-written to be more of a PCI bridge thing, * and the PCI code basically does all the resource handling. * * Linus, Jan 2000 */ #include <linux/kernel.h> #include <linux/module.h> #include <linux/pci.h> #include <pcmcia/ss.h> static void cardbus_config_irq_and_cls(struct pci_bus *bus, int irq) { struct pci_dev *dev; list_for_each_entry(dev, &bus->devices, bus_list) { u8 irq_pin; /* * Since there is only one interrupt available to * CardBus devices, all devices downstream of this * device must be using this IRQ. */ pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &irq_pin); if (irq_pin) { dev->irq = irq; pci_write_config_byte(dev, PCI_INTERRUPT_LINE, dev->irq); } /* * Some controllers transfer very slowly with 0 CLS. * Configure it. This may fail as CLS configuration * is mandatory only for MWI. */ pci_set_cacheline_size(dev); if (dev->subordinate) cardbus_config_irq_and_cls(dev->subordinate, irq); } } /** * cb_alloc() - add CardBus device * @s: the pcmcia_socket where the CardBus device is located * * cb_alloc() allocates the kernel data structures for a Cardbus device * and handles the lowest level PCI device setup issues. */ int __ref cb_alloc(struct pcmcia_socket *s) { struct pci_bus *bus = s->cb_dev->subordinate; struct pci_dev *dev; unsigned int max, pass; s->functions = pci_scan_slot(bus, PCI_DEVFN(0, 0)); pci_fixup_cardbus(bus); max = bus->secondary; for (pass = 0; pass < 2; pass++) list_for_each_entry(dev, &bus->devices, bus_list) if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE || dev->hdr_type == PCI_HEADER_TYPE_CARDBUS) max = pci_scan_bridge(bus, dev, max, pass); /* * Size all resources below the CardBus controller. */ pci_bus_size_bridges(bus); pci_bus_assign_resources(bus); cardbus_config_irq_and_cls(bus, s->pci_irq); /* socket specific tune function */ if (s->tune_bridge) s->tune_bridge(s, bus); pci_enable_bridges(bus); pci_bus_add_devices(bus); return 0; } /** * cb_free() - remove CardBus device * @s: the pcmcia_socket where the CardBus device was located * * cb_free() handles the lowest level PCI device cleanup. */ void cb_free(struct pcmcia_socket *s) { struct pci_dev *bridge = s->cb_dev; if (bridge) pci_stop_and_remove_behind_bridge(bridge); } |