Loading...
1/*******************************************************************************
2
3 Intel PRO/1000 Linux driver
4 Copyright(c) 1999 - 2012 Intel Corporation.
5
6 This program is free software; you can redistribute it and/or modify it
7 under the terms and conditions of the GNU General Public License,
8 version 2, as published by the Free Software Foundation.
9
10 This program is distributed in the hope it will be useful, but WITHOUT
11 ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
12 FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
13 more details.
14
15 You should have received a copy of the GNU General Public License along with
16 this program; if not, write to the Free Software Foundation, Inc.,
17 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
18
19 The full GNU General Public License is included in this distribution in
20 the file called "COPYING".
21
22 Contact Information:
23 Linux NICS <linux.nics@intel.com>
24 e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
25 Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
26
27*******************************************************************************/
28
29#ifndef _E1000_DEFINES_H_
30#define _E1000_DEFINES_H_
31
32#define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */
33#define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */
34#define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */
35#define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */
36#define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */
37#define E1000_TXD_CMD_RS 0x08000000 /* Report Status */
38#define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */
39#define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */
40#define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */
41#define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */
42#define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */
43#define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */
44#define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */
45#define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */
46#define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */
47#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */
48#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */
49#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */
50
51/* Number of Transmit and Receive Descriptors must be a multiple of 8 */
52#define REQ_TX_DESCRIPTOR_MULTIPLE 8
53#define REQ_RX_DESCRIPTOR_MULTIPLE 8
54
55/* Definitions for power management and wakeup registers */
56/* Wake Up Control */
57#define E1000_WUC_APME 0x00000001 /* APM Enable */
58#define E1000_WUC_PME_EN 0x00000002 /* PME Enable */
59#define E1000_WUC_PHY_WAKE 0x00000100 /* if PHY supports wakeup */
60
61/* Wake Up Filter Control */
62#define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
63#define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */
64#define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */
65#define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */
66#define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */
67#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */
68
69/* Wake Up Status */
70#define E1000_WUS_LNKC E1000_WUFC_LNKC
71#define E1000_WUS_MAG E1000_WUFC_MAG
72#define E1000_WUS_EX E1000_WUFC_EX
73#define E1000_WUS_MC E1000_WUFC_MC
74#define E1000_WUS_BC E1000_WUFC_BC
75
76/* Extended Device Control */
77#define E1000_CTRL_EXT_LPCD 0x00000004 /* LCD Power Cycle Done */
78#define E1000_CTRL_EXT_SDP3_DATA 0x00000080 /* Value of SW Definable Pin 3 */
79#define E1000_CTRL_EXT_FORCE_SMBUS 0x00000800 /* Force SMBus mode */
80#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
81#define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */
82#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */
83#define E1000_CTRL_EXT_DMA_DYN_CLK_EN 0x00080000 /* DMA Dynamic Clock Gating */
84#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
85#define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000
86#define E1000_CTRL_EXT_EIAME 0x01000000
87#define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */
88#define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */
89#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */
90#define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */
91#define E1000_CTRL_EXT_LSECCK 0x00001000
92#define E1000_CTRL_EXT_PHYPDEN 0x00100000
93
94/* Receive Descriptor bit definitions */
95#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
96#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
97#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
98#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
99#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */
100#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
101#define E1000_RXD_ERR_CE 0x01 /* CRC Error */
102#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */
103#define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */
104#define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */
105#define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */
106#define E1000_RXD_ERR_IPE 0x40 /* IP Checksum Error */
107#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */
108#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */
109
110#define E1000_RXDEXT_STATERR_CE 0x01000000
111#define E1000_RXDEXT_STATERR_SE 0x02000000
112#define E1000_RXDEXT_STATERR_SEQ 0x04000000
113#define E1000_RXDEXT_STATERR_CXE 0x10000000
114#define E1000_RXDEXT_STATERR_RXE 0x80000000
115
116/* mask to determine if packets should be dropped due to frame errors */
117#define E1000_RXD_ERR_FRAME_ERR_MASK ( \
118 E1000_RXD_ERR_CE | \
119 E1000_RXD_ERR_SE | \
120 E1000_RXD_ERR_SEQ | \
121 E1000_RXD_ERR_CXE | \
122 E1000_RXD_ERR_RXE)
123
124/* Same mask, but for extended and packet split descriptors */
125#define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \
126 E1000_RXDEXT_STATERR_CE | \
127 E1000_RXDEXT_STATERR_SE | \
128 E1000_RXDEXT_STATERR_SEQ | \
129 E1000_RXDEXT_STATERR_CXE | \
130 E1000_RXDEXT_STATERR_RXE)
131
132#define E1000_MRQC_RSS_FIELD_MASK 0xFFFF0000
133#define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000
134#define E1000_MRQC_RSS_FIELD_IPV4 0x00020000
135#define E1000_MRQC_RSS_FIELD_IPV6_TCP_EX 0x00040000
136#define E1000_MRQC_RSS_FIELD_IPV6 0x00100000
137#define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00200000
138
139#define E1000_RXDPS_HDRSTAT_HDRSP 0x00008000
140
141/* Management Control */
142#define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */
143#define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */
144#define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */
145#define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */
146#define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */
147/* Enable MAC address filtering */
148#define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000
149/* Enable MNG packets to host memory */
150#define E1000_MANC_EN_MNG2HOST 0x00200000
151
152#define E1000_MANC2H_PORT_623 0x00000020 /* Port 0x26f */
153#define E1000_MANC2H_PORT_664 0x00000040 /* Port 0x298 */
154#define E1000_MDEF_PORT_623 0x00000800 /* Port 0x26f */
155#define E1000_MDEF_PORT_664 0x00000400 /* Port 0x298 */
156
157/* Receive Control */
158#define E1000_RCTL_EN 0x00000002 /* enable */
159#define E1000_RCTL_SBP 0x00000004 /* store bad packet */
160#define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */
161#define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */
162#define E1000_RCTL_LPE 0x00000020 /* long packet enable */
163#define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */
164#define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */
165#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
166#define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */
167#define E1000_RCTL_RDMTS_HALF 0x00000000 /* Rx desc min threshold size */
168#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
169#define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */
170#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
171/* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */
172#define E1000_RCTL_SZ_2048 0x00000000 /* Rx buffer size 2048 */
173#define E1000_RCTL_SZ_1024 0x00010000 /* Rx buffer size 1024 */
174#define E1000_RCTL_SZ_512 0x00020000 /* Rx buffer size 512 */
175#define E1000_RCTL_SZ_256 0x00030000 /* Rx buffer size 256 */
176/* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */
177#define E1000_RCTL_SZ_16384 0x00010000 /* Rx buffer size 16384 */
178#define E1000_RCTL_SZ_8192 0x00020000 /* Rx buffer size 8192 */
179#define E1000_RCTL_SZ_4096 0x00030000 /* Rx buffer size 4096 */
180#define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */
181#define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */
182#define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */
183#define E1000_RCTL_DPF 0x00400000 /* Discard Pause Frames */
184#define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */
185#define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */
186#define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */
187
188/*
189 * Use byte values for the following shift parameters
190 * Usage:
191 * psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) &
192 * E1000_PSRCTL_BSIZE0_MASK) |
193 * ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) &
194 * E1000_PSRCTL_BSIZE1_MASK) |
195 * ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) &
196 * E1000_PSRCTL_BSIZE2_MASK) |
197 * ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |;
198 * E1000_PSRCTL_BSIZE3_MASK))
199 * where value0 = [128..16256], default=256
200 * value1 = [1024..64512], default=4096
201 * value2 = [0..64512], default=4096
202 * value3 = [0..64512], default=0
203 */
204
205#define E1000_PSRCTL_BSIZE0_MASK 0x0000007F
206#define E1000_PSRCTL_BSIZE1_MASK 0x00003F00
207#define E1000_PSRCTL_BSIZE2_MASK 0x003F0000
208#define E1000_PSRCTL_BSIZE3_MASK 0x3F000000
209
210#define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */
211#define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */
212#define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */
213#define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */
214
215/* SWFW_SYNC Definitions */
216#define E1000_SWFW_EEP_SM 0x1
217#define E1000_SWFW_PHY0_SM 0x2
218#define E1000_SWFW_PHY1_SM 0x4
219#define E1000_SWFW_CSR_SM 0x8
220
221/* Device Control */
222#define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */
223#define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */
224#define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */
225#define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */
226#define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */
227#define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */
228#define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */
229#define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */
230#define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */
231#define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */
232#define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */
233#define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */
234#define E1000_CTRL_LANPHYPC_OVERRIDE 0x00010000 /* SW control of LANPHYPC */
235#define E1000_CTRL_LANPHYPC_VALUE 0x00020000 /* SW value of LANPHYPC */
236#define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */
237#define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */
238#define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */
239#define E1000_CTRL_RST 0x04000000 /* Global reset */
240#define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */
241#define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */
242#define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */
243#define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */
244
245/*
246 * Bit definitions for the Management Data IO (MDIO) and Management Data
247 * Clock (MDC) pins in the Device Control Register.
248 */
249
250/* Device Status */
251#define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */
252#define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */
253#define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */
254#define E1000_STATUS_FUNC_SHIFT 2
255#define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */
256#define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */
257#define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */
258#define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */
259#define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */
260#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion by NVM */
261#define E1000_STATUS_PHYRA 0x00000400 /* PHY Reset Asserted */
262#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
263
264/* Constants used to interpret the masked PCI-X bus speed. */
265
266#define HALF_DUPLEX 1
267#define FULL_DUPLEX 2
268
269
270#define ADVERTISE_10_HALF 0x0001
271#define ADVERTISE_10_FULL 0x0002
272#define ADVERTISE_100_HALF 0x0004
273#define ADVERTISE_100_FULL 0x0008
274#define ADVERTISE_1000_HALF 0x0010 /* Not used, just FYI */
275#define ADVERTISE_1000_FULL 0x0020
276
277/* 1000/H is not supported, nor spec-compliant. */
278#define E1000_ALL_SPEED_DUPLEX ( ADVERTISE_10_HALF | ADVERTISE_10_FULL | \
279 ADVERTISE_100_HALF | ADVERTISE_100_FULL | \
280 ADVERTISE_1000_FULL)
281#define E1000_ALL_NOT_GIG ( ADVERTISE_10_HALF | ADVERTISE_10_FULL | \
282 ADVERTISE_100_HALF | ADVERTISE_100_FULL)
283#define E1000_ALL_100_SPEED (ADVERTISE_100_HALF | ADVERTISE_100_FULL)
284#define E1000_ALL_10_SPEED (ADVERTISE_10_HALF | ADVERTISE_10_FULL)
285#define E1000_ALL_HALF_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_100_HALF)
286
287#define AUTONEG_ADVERTISE_SPEED_DEFAULT E1000_ALL_SPEED_DUPLEX
288
289/* LED Control */
290#define E1000_PHY_LED0_MODE_MASK 0x00000007
291#define E1000_PHY_LED0_IVRT 0x00000008
292#define E1000_PHY_LED0_MASK 0x0000001F
293
294#define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F
295#define E1000_LEDCTL_LED0_MODE_SHIFT 0
296#define E1000_LEDCTL_LED0_IVRT 0x00000040
297#define E1000_LEDCTL_LED0_BLINK 0x00000080
298
299#define E1000_LEDCTL_MODE_LINK_UP 0x2
300#define E1000_LEDCTL_MODE_LED_ON 0xE
301#define E1000_LEDCTL_MODE_LED_OFF 0xF
302
303/* Transmit Descriptor bit definitions */
304#define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */
305#define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */
306#define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */
307#define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */
308#define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */
309#define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */
310#define E1000_TXD_CMD_RS 0x08000000 /* Report Status */
311#define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */
312#define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */
313#define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */
314#define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */
315#define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */
316#define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */
317#define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */
318#define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */
319#define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */
320#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */
321#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */
322#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */
323
324/* Transmit Control */
325#define E1000_TCTL_EN 0x00000002 /* enable Tx */
326#define E1000_TCTL_PSP 0x00000008 /* pad short packets */
327#define E1000_TCTL_CT 0x00000ff0 /* collision threshold */
328#define E1000_TCTL_COLD 0x003ff000 /* collision distance */
329#define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */
330#define E1000_TCTL_MULR 0x10000000 /* Multiple request support */
331
332/* Transmit Arbitration Count */
333
334/* SerDes Control */
335#define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400
336
337/* Receive Checksum Control */
338#define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */
339#define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */
340#define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */
341
342/* Header split receive */
343#define E1000_RFCTL_NFSW_DIS 0x00000040
344#define E1000_RFCTL_NFSR_DIS 0x00000080
345#define E1000_RFCTL_ACK_DIS 0x00001000
346#define E1000_RFCTL_EXTEN 0x00008000
347#define E1000_RFCTL_IPV6_EX_DIS 0x00010000
348#define E1000_RFCTL_NEW_IPV6_EXT_DIS 0x00020000
349
350/* Collision related configuration parameters */
351#define E1000_COLLISION_THRESHOLD 15
352#define E1000_CT_SHIFT 4
353#define E1000_COLLISION_DISTANCE 63
354#define E1000_COLD_SHIFT 12
355
356/* Default values for the transmit IPG register */
357#define DEFAULT_82543_TIPG_IPGT_COPPER 8
358
359#define E1000_TIPG_IPGT_MASK 0x000003FF
360
361#define DEFAULT_82543_TIPG_IPGR1 8
362#define E1000_TIPG_IPGR1_SHIFT 10
363
364#define DEFAULT_82543_TIPG_IPGR2 6
365#define DEFAULT_80003ES2LAN_TIPG_IPGR2 7
366#define E1000_TIPG_IPGR2_SHIFT 20
367
368#define MAX_JUMBO_FRAME_SIZE 0x3F00
369
370/* Extended Configuration Control and Size */
371#define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020
372#define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE 0x00000001
373#define E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE 0x00000008
374#define E1000_EXTCNF_CTRL_SWFLAG 0x00000020
375#define E1000_EXTCNF_CTRL_GATE_PHY_CFG 0x00000080
376#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK 0x00FF0000
377#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT 16
378#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK 0x0FFF0000
379#define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT 16
380
381#define E1000_PHY_CTRL_D0A_LPLU 0x00000002
382#define E1000_PHY_CTRL_NOND0A_LPLU 0x00000004
383#define E1000_PHY_CTRL_NOND0A_GBE_DISABLE 0x00000008
384#define E1000_PHY_CTRL_GBE_DISABLE 0x00000040
385
386#define E1000_KABGTXD_BGSQLBIAS 0x00050000
387
388/* PBA constants */
389#define E1000_PBA_8K 0x0008 /* 8KB */
390#define E1000_PBA_16K 0x0010 /* 16KB */
391
392#define E1000_PBS_16K E1000_PBA_16K
393
394#define IFS_MAX 80
395#define IFS_MIN 40
396#define IFS_RATIO 4
397#define IFS_STEP 10
398#define MIN_NUM_XMITS 1000
399
400/* SW Semaphore Register */
401#define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */
402#define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */
403#define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */
404
405#define E1000_SWSM2_LOCK 0x00000002 /* Secondary driver semaphore bit */
406
407/* Interrupt Cause Read */
408#define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */
409#define E1000_ICR_LSC 0x00000004 /* Link Status Change */
410#define E1000_ICR_RXSEQ 0x00000008 /* Rx sequence error */
411#define E1000_ICR_RXDMT0 0x00000010 /* Rx desc min. threshold (0) */
412#define E1000_ICR_RXT0 0x00000080 /* Rx timer intr (ring 0) */
413#define E1000_ICR_INT_ASSERTED 0x80000000 /* If this bit asserted, the driver should claim the interrupt */
414#define E1000_ICR_RXQ0 0x00100000 /* Rx Queue 0 Interrupt */
415#define E1000_ICR_RXQ1 0x00200000 /* Rx Queue 1 Interrupt */
416#define E1000_ICR_TXQ0 0x00400000 /* Tx Queue 0 Interrupt */
417#define E1000_ICR_TXQ1 0x00800000 /* Tx Queue 1 Interrupt */
418#define E1000_ICR_OTHER 0x01000000 /* Other Interrupts */
419
420/* PBA ECC Register */
421#define E1000_PBA_ECC_COUNTER_MASK 0xFFF00000 /* ECC counter mask */
422#define E1000_PBA_ECC_COUNTER_SHIFT 20 /* ECC counter shift value */
423#define E1000_PBA_ECC_CORR_EN 0x00000001 /* ECC correction enable */
424#define E1000_PBA_ECC_STAT_CLR 0x00000002 /* Clear ECC error counter */
425#define E1000_PBA_ECC_INT_EN 0x00000004 /* Enable ICR bit 5 for ECC */
426
427/*
428 * This defines the bits that are set in the Interrupt Mask
429 * Set/Read Register. Each bit is documented below:
430 * o RXT0 = Receiver Timer Interrupt (ring 0)
431 * o TXDW = Transmit Descriptor Written Back
432 * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0)
433 * o RXSEQ = Receive Sequence Error
434 * o LSC = Link Status Change
435 */
436#define IMS_ENABLE_MASK ( \
437 E1000_IMS_RXT0 | \
438 E1000_IMS_TXDW | \
439 E1000_IMS_RXDMT0 | \
440 E1000_IMS_RXSEQ | \
441 E1000_IMS_LSC)
442
443/* Interrupt Mask Set */
444#define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
445#define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */
446#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* Rx sequence error */
447#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* Rx desc min. threshold */
448#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* Rx timer intr */
449#define E1000_IMS_RXQ0 E1000_ICR_RXQ0 /* Rx Queue 0 Interrupt */
450#define E1000_IMS_RXQ1 E1000_ICR_RXQ1 /* Rx Queue 1 Interrupt */
451#define E1000_IMS_TXQ0 E1000_ICR_TXQ0 /* Tx Queue 0 Interrupt */
452#define E1000_IMS_TXQ1 E1000_ICR_TXQ1 /* Tx Queue 1 Interrupt */
453#define E1000_IMS_OTHER E1000_ICR_OTHER /* Other Interrupts */
454
455/* Interrupt Cause Set */
456#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
457#define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* Rx sequence error */
458#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* Rx desc min. threshold */
459
460/* Transmit Descriptor Control */
461#define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */
462#define E1000_TXDCTL_HTHRESH 0x00003F00 /* TXDCTL Host Threshold */
463#define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */
464#define E1000_TXDCTL_GRAN 0x01000000 /* TXDCTL Granularity */
465#define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */
466#define E1000_TXDCTL_MAX_TX_DESC_PREFETCH 0x0100001F /* GRAN=1, PTHRESH=31 */
467/* Enable the counting of desc. still to be processed. */
468#define E1000_TXDCTL_COUNT_DESC 0x00400000
469
470/* Flow Control Constants */
471#define FLOW_CONTROL_ADDRESS_LOW 0x00C28001
472#define FLOW_CONTROL_ADDRESS_HIGH 0x00000100
473#define FLOW_CONTROL_TYPE 0x8808
474
475/* 802.1q VLAN Packet Size */
476#define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */
477
478/* Receive Address */
479/*
480 * Number of high/low register pairs in the RAR. The RAR (Receive Address
481 * Registers) holds the directed and multicast addresses that we monitor.
482 * Technically, we have 16 spots. However, we reserve one of these spots
483 * (RAR[15]) for our directed address used by controllers with
484 * manageability enabled, allowing us room for 15 multicast addresses.
485 */
486#define E1000_RAR_ENTRIES 15
487#define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */
488#define E1000_RAL_MAC_ADDR_LEN 4
489#define E1000_RAH_MAC_ADDR_LEN 2
490
491/* Error Codes */
492#define E1000_ERR_NVM 1
493#define E1000_ERR_PHY 2
494#define E1000_ERR_CONFIG 3
495#define E1000_ERR_PARAM 4
496#define E1000_ERR_MAC_INIT 5
497#define E1000_ERR_PHY_TYPE 6
498#define E1000_ERR_RESET 9
499#define E1000_ERR_MASTER_REQUESTS_PENDING 10
500#define E1000_ERR_HOST_INTERFACE_COMMAND 11
501#define E1000_BLK_PHY_RESET 12
502#define E1000_ERR_SWFW_SYNC 13
503#define E1000_NOT_IMPLEMENTED 14
504#define E1000_ERR_INVALID_ARGUMENT 16
505#define E1000_ERR_NO_SPACE 17
506#define E1000_ERR_NVM_PBA_SECTION 18
507
508/* Loop limit on how long we wait for auto-negotiation to complete */
509#define FIBER_LINK_UP_LIMIT 50
510#define COPPER_LINK_UP_LIMIT 10
511#define PHY_AUTO_NEG_LIMIT 45
512#define PHY_FORCE_LIMIT 20
513/* Number of 100 microseconds we wait for PCI Express master disable */
514#define MASTER_DISABLE_TIMEOUT 800
515/* Number of milliseconds we wait for PHY configuration done after MAC reset */
516#define PHY_CFG_TIMEOUT 100
517/* Number of 2 milliseconds we wait for acquiring MDIO ownership. */
518#define MDIO_OWNERSHIP_TIMEOUT 10
519/* Number of milliseconds for NVM auto read done after MAC reset. */
520#define AUTO_READ_DONE_TIMEOUT 10
521
522/* Flow Control */
523#define E1000_FCRTH_RTH 0x0000FFF8 /* Mask Bits[15:3] for RTH */
524#define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */
525#define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */
526
527/* Transmit Configuration Word */
528#define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */
529#define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */
530#define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */
531#define E1000_TXCW_PAUSE_MASK 0x00000180 /* TXCW pause request mask */
532#define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */
533
534/* Receive Configuration Word */
535#define E1000_RXCW_CW 0x0000ffff /* RxConfigWord mask */
536#define E1000_RXCW_IV 0x08000000 /* Receive config invalid */
537#define E1000_RXCW_C 0x20000000 /* Receive config */
538#define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */
539
540/* PCI Express Control */
541#define E1000_GCR_RXD_NO_SNOOP 0x00000001
542#define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002
543#define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004
544#define E1000_GCR_TXD_NO_SNOOP 0x00000008
545#define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010
546#define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020
547
548#define PCIE_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \
549 E1000_GCR_RXDSCW_NO_SNOOP | \
550 E1000_GCR_RXDSCR_NO_SNOOP | \
551 E1000_GCR_TXD_NO_SNOOP | \
552 E1000_GCR_TXDSCW_NO_SNOOP | \
553 E1000_GCR_TXDSCR_NO_SNOOP)
554
555/* PHY Control Register */
556#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */
557#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */
558#define MII_CR_POWER_DOWN 0x0800 /* Power down */
559#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */
560#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */
561#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */
562#define MII_CR_SPEED_1000 0x0040
563#define MII_CR_SPEED_100 0x2000
564#define MII_CR_SPEED_10 0x0000
565
566/* PHY Status Register */
567#define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */
568#define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */
569
570/* Autoneg Advertisement Register */
571#define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */
572#define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */
573#define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */
574#define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */
575#define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */
576#define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */
577
578/* Link Partner Ability Register (Base Page) */
579#define NWAY_LPAR_100TX_FD_CAPS 0x0100 /* LP 100TX Full Dplx Capable */
580#define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */
581#define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */
582
583/* Autoneg Expansion Register */
584#define NWAY_ER_LP_NWAY_CAPS 0x0001 /* LP has Auto Neg Capability */
585
586/* 1000BASE-T Control Register */
587#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */
588#define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */
589 /* 0=DTE device */
590#define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */
591 /* 0=Configure PHY as Slave */
592#define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */
593 /* 0=Automatic Master/Slave config */
594
595/* 1000BASE-T Status Register */
596#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
597#define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */
598
599
600/* PHY 1000 MII Register/Bit Definitions */
601/* PHY Registers defined by IEEE */
602#define PHY_CONTROL 0x00 /* Control Register */
603#define PHY_STATUS 0x01 /* Status Register */
604#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */
605#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */
606#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
607#define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */
608#define PHY_AUTONEG_EXP 0x06 /* Autoneg Expansion Reg */
609#define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */
610#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
611#define PHY_EXT_STATUS 0x0F /* Extended Status Reg */
612
613#define PHY_CONTROL_LB 0x4000 /* PHY Loopback bit */
614
615/* NVM Control */
616#define E1000_EECD_SK 0x00000001 /* NVM Clock */
617#define E1000_EECD_CS 0x00000002 /* NVM Chip Select */
618#define E1000_EECD_DI 0x00000004 /* NVM Data In */
619#define E1000_EECD_DO 0x00000008 /* NVM Data Out */
620#define E1000_EECD_REQ 0x00000040 /* NVM Access Request */
621#define E1000_EECD_GNT 0x00000080 /* NVM Access Grant */
622#define E1000_EECD_PRES 0x00000100 /* NVM Present */
623#define E1000_EECD_SIZE 0x00000200 /* NVM Size (0=64 word 1=256 word) */
624/* NVM Addressing bits based on type (0-small, 1-large) */
625#define E1000_EECD_ADDR_BITS 0x00000400
626#define E1000_NVM_GRANT_ATTEMPTS 1000 /* NVM # attempts to gain grant */
627#define E1000_EECD_AUTO_RD 0x00000200 /* NVM Auto Read done */
628#define E1000_EECD_SIZE_EX_MASK 0x00007800 /* NVM Size */
629#define E1000_EECD_SIZE_EX_SHIFT 11
630#define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */
631#define E1000_EECD_AUPDEN 0x00100000 /* Enable Autonomous FLASH update */
632#define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */
633#define E1000_EECD_SEC1VAL_VALID_MASK (E1000_EECD_AUTO_RD | E1000_EECD_PRES)
634
635#define E1000_NVM_RW_REG_DATA 16 /* Offset to data in NVM read/write registers */
636#define E1000_NVM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */
637#define E1000_NVM_RW_REG_START 1 /* Start operation */
638#define E1000_NVM_RW_ADDR_SHIFT 2 /* Shift to the address bits */
639#define E1000_NVM_POLL_WRITE 1 /* Flag for polling for write complete */
640#define E1000_NVM_POLL_READ 0 /* Flag for polling for read complete */
641#define E1000_FLASH_UPDATES 2000
642
643/* NVM Word Offsets */
644#define NVM_COMPAT 0x0003
645#define NVM_ID_LED_SETTINGS 0x0004
646#define NVM_INIT_CONTROL2_REG 0x000F
647#define NVM_INIT_CONTROL3_PORT_B 0x0014
648#define NVM_INIT_3GIO_3 0x001A
649#define NVM_INIT_CONTROL3_PORT_A 0x0024
650#define NVM_CFG 0x0012
651#define NVM_ALT_MAC_ADDR_PTR 0x0037
652#define NVM_CHECKSUM_REG 0x003F
653
654#define E1000_NVM_INIT_CTRL2_MNGM 0x6000 /* Manageability Operation Mode mask */
655
656#define E1000_NVM_CFG_DONE_PORT_0 0x40000 /* MNG config cycle done */
657#define E1000_NVM_CFG_DONE_PORT_1 0x80000 /* ...for second port */
658
659/* Mask bits for fields in Word 0x0f of the NVM */
660#define NVM_WORD0F_PAUSE_MASK 0x3000
661#define NVM_WORD0F_PAUSE 0x1000
662#define NVM_WORD0F_ASM_DIR 0x2000
663
664/* Mask bits for fields in Word 0x1a of the NVM */
665#define NVM_WORD1A_ASPM_MASK 0x000C
666
667/* Mask bits for fields in Word 0x03 of the EEPROM */
668#define NVM_COMPAT_LOM 0x0800
669
670/* length of string needed to store PBA number */
671#define E1000_PBANUM_LENGTH 11
672
673/* For checksumming, the sum of all words in the NVM should equal 0xBABA. */
674#define NVM_SUM 0xBABA
675
676/* PBA (printed board assembly) number words */
677#define NVM_PBA_OFFSET_0 8
678#define NVM_PBA_OFFSET_1 9
679#define NVM_PBA_PTR_GUARD 0xFAFA
680#define NVM_WORD_SIZE_BASE_SHIFT 6
681
682/* NVM Commands - SPI */
683#define NVM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */
684#define NVM_READ_OPCODE_SPI 0x03 /* NVM read opcode */
685#define NVM_WRITE_OPCODE_SPI 0x02 /* NVM write opcode */
686#define NVM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */
687#define NVM_WREN_OPCODE_SPI 0x06 /* NVM set Write Enable latch */
688#define NVM_RDSR_OPCODE_SPI 0x05 /* NVM read Status register */
689
690/* SPI NVM Status Register */
691#define NVM_STATUS_RDY_SPI 0x01
692
693/* Word definitions for ID LED Settings */
694#define ID_LED_RESERVED_0000 0x0000
695#define ID_LED_RESERVED_FFFF 0xFFFF
696#define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \
697 (ID_LED_OFF1_OFF2 << 8) | \
698 (ID_LED_DEF1_DEF2 << 4) | \
699 (ID_LED_DEF1_DEF2))
700#define ID_LED_DEF1_DEF2 0x1
701#define ID_LED_DEF1_ON2 0x2
702#define ID_LED_DEF1_OFF2 0x3
703#define ID_LED_ON1_DEF2 0x4
704#define ID_LED_ON1_ON2 0x5
705#define ID_LED_ON1_OFF2 0x6
706#define ID_LED_OFF1_DEF2 0x7
707#define ID_LED_OFF1_ON2 0x8
708#define ID_LED_OFF1_OFF2 0x9
709
710#define IGP_ACTIVITY_LED_MASK 0xFFFFF0FF
711#define IGP_ACTIVITY_LED_ENABLE 0x0300
712#define IGP_LED3_MODE 0x07000000
713
714/* PCI/PCI-X/PCI-EX Config space */
715#define PCI_HEADER_TYPE_REGISTER 0x0E
716#define PCIE_LINK_STATUS 0x12
717
718#define PCI_HEADER_TYPE_MULTIFUNC 0x80
719#define PCIE_LINK_WIDTH_MASK 0x3F0
720#define PCIE_LINK_WIDTH_SHIFT 4
721
722#define PHY_REVISION_MASK 0xFFFFFFF0
723#define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */
724#define MAX_PHY_MULTI_PAGE_REG 0xF
725
726/* Bit definitions for valid PHY IDs. */
727/*
728 * I = Integrated
729 * E = External
730 */
731#define M88E1000_E_PHY_ID 0x01410C50
732#define M88E1000_I_PHY_ID 0x01410C30
733#define M88E1011_I_PHY_ID 0x01410C20
734#define IGP01E1000_I_PHY_ID 0x02A80380
735#define M88E1111_I_PHY_ID 0x01410CC0
736#define GG82563_E_PHY_ID 0x01410CA0
737#define IGP03E1000_E_PHY_ID 0x02A80390
738#define IFE_E_PHY_ID 0x02A80330
739#define IFE_PLUS_E_PHY_ID 0x02A80320
740#define IFE_C_E_PHY_ID 0x02A80310
741#define BME1000_E_PHY_ID 0x01410CB0
742#define BME1000_E_PHY_ID_R2 0x01410CB1
743#define I82577_E_PHY_ID 0x01540050
744#define I82578_E_PHY_ID 0x004DD040
745#define I82579_E_PHY_ID 0x01540090
746#define I217_E_PHY_ID 0x015400A0
747
748/* M88E1000 Specific Registers */
749#define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */
750#define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */
751#define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */
752
753#define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */
754#define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */
755
756/* M88E1000 PHY Specific Control Register */
757#define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */
758#define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */
759 /* Manual MDI configuration */
760#define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */
761/* 1000BASE-T: Auto crossover, 100BASE-TX/10BASE-T: MDI Mode */
762#define M88E1000_PSCR_AUTO_X_1000T 0x0040
763/* Auto crossover enabled all speeds */
764#define M88E1000_PSCR_AUTO_X_MODE 0x0060
765/*
766 * 1=Enable Extended 10BASE-T distance (Lower 10BASE-T Rx Threshold)
767 * 0=Normal 10BASE-T Rx Threshold
768 */
769#define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
770
771/* M88E1000 PHY Specific Status Register */
772#define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */
773#define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */
774#define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */
775/* 0=<50M; 1=50-80M; 2=80-110M; 3=110-140M; 4=>140M */
776#define M88E1000_PSSR_CABLE_LENGTH 0x0380
777#define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */
778#define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */
779
780#define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7
781
782/*
783 * Number of times we will attempt to autonegotiate before downshifting if we
784 * are the master
785 */
786#define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00
787#define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 0x0000
788/*
789 * Number of times we will attempt to autonegotiate before downshifting if we
790 * are the slave
791 */
792#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK 0x0300
793#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100
794#define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */
795
796/* M88EC018 Rev 2 specific DownShift settings */
797#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00
798#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800
799
800#define I82578_EPSCR_DOWNSHIFT_ENABLE 0x0020
801#define I82578_EPSCR_DOWNSHIFT_COUNTER_MASK 0x001C
802
803/* BME1000 PHY Specific Control Register */
804#define BME1000_PSCR_ENABLE_DOWNSHIFT 0x0800 /* 1 = enable downshift */
805
806
807#define PHY_PAGE_SHIFT 5
808#define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \
809 ((reg) & MAX_PHY_REG_ADDRESS))
810
811/*
812 * Bits...
813 * 15-5: page
814 * 4-0: register offset
815 */
816#define GG82563_PAGE_SHIFT 5
817#define GG82563_REG(page, reg) \
818 (((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS))
819#define GG82563_MIN_ALT_REG 30
820
821/* GG82563 Specific Registers */
822#define GG82563_PHY_SPEC_CTRL \
823 GG82563_REG(0, 16) /* PHY Specific Control */
824#define GG82563_PHY_PAGE_SELECT \
825 GG82563_REG(0, 22) /* Page Select */
826#define GG82563_PHY_SPEC_CTRL_2 \
827 GG82563_REG(0, 26) /* PHY Specific Control 2 */
828#define GG82563_PHY_PAGE_SELECT_ALT \
829 GG82563_REG(0, 29) /* Alternate Page Select */
830
831#define GG82563_PHY_MAC_SPEC_CTRL \
832 GG82563_REG(2, 21) /* MAC Specific Control Register */
833
834#define GG82563_PHY_DSP_DISTANCE \
835 GG82563_REG(5, 26) /* DSP Distance */
836
837/* Page 193 - Port Control Registers */
838#define GG82563_PHY_KMRN_MODE_CTRL \
839 GG82563_REG(193, 16) /* Kumeran Mode Control */
840#define GG82563_PHY_PWR_MGMT_CTRL \
841 GG82563_REG(193, 20) /* Power Management Control */
842
843/* Page 194 - KMRN Registers */
844#define GG82563_PHY_INBAND_CTRL \
845 GG82563_REG(194, 18) /* Inband Control */
846
847/* MDI Control */
848#define E1000_MDIC_REG_SHIFT 16
849#define E1000_MDIC_PHY_SHIFT 21
850#define E1000_MDIC_OP_WRITE 0x04000000
851#define E1000_MDIC_OP_READ 0x08000000
852#define E1000_MDIC_READY 0x10000000
853#define E1000_MDIC_ERROR 0x40000000
854
855/* SerDes Control */
856#define E1000_GEN_POLL_TIMEOUT 640
857
858/* FW Semaphore */
859#define E1000_FWSM_WLOCK_MAC_MASK 0x0380
860#define E1000_FWSM_WLOCK_MAC_SHIFT 7
861
862#endif /* _E1000_DEFINES_H_ */