Loading...
Note: File does not exist in v3.5.6.
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * Driver for IDT Versaclock 5
4 *
5 * Copyright (C) 2017 Marek Vasut <marek.vasut@gmail.com>
6 */
7
8/*
9 * Possible optimizations:
10 * - Use spread spectrum
11 * - Use integer divider in FOD if applicable
12 */
13
14#include <linux/clk.h>
15#include <linux/clk-provider.h>
16#include <linux/delay.h>
17#include <linux/i2c.h>
18#include <linux/interrupt.h>
19#include <linux/mod_devicetable.h>
20#include <linux/module.h>
21#include <linux/of.h>
22#include <linux/property.h>
23#include <linux/regmap.h>
24#include <linux/slab.h>
25
26#include <dt-bindings/clock/versaclock.h>
27
28/* VersaClock5 registers */
29#define VC5_OTP_CONTROL 0x00
30
31/* Factory-reserved register block */
32#define VC5_RSVD_DEVICE_ID 0x01
33#define VC5_RSVD_ADC_GAIN_7_0 0x02
34#define VC5_RSVD_ADC_GAIN_15_8 0x03
35#define VC5_RSVD_ADC_OFFSET_7_0 0x04
36#define VC5_RSVD_ADC_OFFSET_15_8 0x05
37#define VC5_RSVD_TEMPY 0x06
38#define VC5_RSVD_OFFSET_TBIN 0x07
39#define VC5_RSVD_GAIN 0x08
40#define VC5_RSVD_TEST_NP 0x09
41#define VC5_RSVD_UNUSED 0x0a
42#define VC5_RSVD_BANDGAP_TRIM_UP 0x0b
43#define VC5_RSVD_BANDGAP_TRIM_DN 0x0c
44#define VC5_RSVD_CLK_R_12_CLK_AMP_4 0x0d
45#define VC5_RSVD_CLK_R_34_CLK_AMP_4 0x0e
46#define VC5_RSVD_CLK_AMP_123 0x0f
47
48/* Configuration register block */
49#define VC5_PRIM_SRC_SHDN 0x10
50#define VC5_PRIM_SRC_SHDN_EN_XTAL BIT(7)
51#define VC5_PRIM_SRC_SHDN_EN_CLKIN BIT(6)
52#define VC5_PRIM_SRC_SHDN_EN_DOUBLE_XTAL_FREQ BIT(3)
53#define VC5_PRIM_SRC_SHDN_SP BIT(1)
54#define VC5_PRIM_SRC_SHDN_EN_GBL_SHDN BIT(0)
55
56#define VC5_VCO_BAND 0x11
57#define VC5_XTAL_X1_LOAD_CAP 0x12
58#define VC5_XTAL_X2_LOAD_CAP 0x13
59#define VC5_REF_DIVIDER 0x15
60#define VC5_REF_DIVIDER_SEL_PREDIV2 BIT(7)
61#define VC5_REF_DIVIDER_REF_DIV(n) ((n) & 0x3f)
62
63#define VC5_VCO_CTRL_AND_PREDIV 0x16
64#define VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV BIT(7)
65
66#define VC5_FEEDBACK_INT_DIV 0x17
67#define VC5_FEEDBACK_INT_DIV_BITS 0x18
68#define VC5_FEEDBACK_FRAC_DIV(n) (0x19 + (n))
69#define VC5_RC_CONTROL0 0x1e
70#define VC5_RC_CONTROL1 0x1f
71
72/* These registers are named "Unused Factory Reserved Registers" */
73#define VC5_RESERVED_X0(idx) (0x20 + ((idx) * 0x10))
74#define VC5_RESERVED_X0_BYPASS_SYNC BIT(7) /* bypass_sync<idx> bit */
75
76/* Output divider control for divider 1,2,3,4 */
77#define VC5_OUT_DIV_CONTROL(idx) (0x21 + ((idx) * 0x10))
78#define VC5_OUT_DIV_CONTROL_RESET BIT(7)
79#define VC5_OUT_DIV_CONTROL_SELB_NORM BIT(3)
80#define VC5_OUT_DIV_CONTROL_SEL_EXT BIT(2)
81#define VC5_OUT_DIV_CONTROL_INT_MODE BIT(1)
82#define VC5_OUT_DIV_CONTROL_EN_FOD BIT(0)
83
84#define VC5_OUT_DIV_FRAC(idx, n) (0x22 + ((idx) * 0x10) + (n))
85#define VC5_OUT_DIV_FRAC4_OD_SCEE BIT(1)
86
87#define VC5_OUT_DIV_STEP_SPREAD(idx, n) (0x26 + ((idx) * 0x10) + (n))
88#define VC5_OUT_DIV_SPREAD_MOD(idx, n) (0x29 + ((idx) * 0x10) + (n))
89#define VC5_OUT_DIV_SKEW_INT(idx, n) (0x2b + ((idx) * 0x10) + (n))
90#define VC5_OUT_DIV_INT(idx, n) (0x2d + ((idx) * 0x10) + (n))
91#define VC5_OUT_DIV_SKEW_FRAC(idx) (0x2f + ((idx) * 0x10))
92
93/* Clock control register for clock 1,2 */
94#define VC5_CLK_OUTPUT_CFG(idx, n) (0x60 + ((idx) * 0x2) + (n))
95#define VC5_CLK_OUTPUT_CFG0_CFG_SHIFT 5
96#define VC5_CLK_OUTPUT_CFG0_CFG_MASK GENMASK(7, VC5_CLK_OUTPUT_CFG0_CFG_SHIFT)
97
98#define VC5_CLK_OUTPUT_CFG0_CFG_LVPECL (VC5_LVPECL)
99#define VC5_CLK_OUTPUT_CFG0_CFG_CMOS (VC5_CMOS)
100#define VC5_CLK_OUTPUT_CFG0_CFG_HCSL33 (VC5_HCSL33)
101#define VC5_CLK_OUTPUT_CFG0_CFG_LVDS (VC5_LVDS)
102#define VC5_CLK_OUTPUT_CFG0_CFG_CMOS2 (VC5_CMOS2)
103#define VC5_CLK_OUTPUT_CFG0_CFG_CMOSD (VC5_CMOSD)
104#define VC5_CLK_OUTPUT_CFG0_CFG_HCSL25 (VC5_HCSL25)
105
106#define VC5_CLK_OUTPUT_CFG0_PWR_SHIFT 3
107#define VC5_CLK_OUTPUT_CFG0_PWR_MASK GENMASK(4, VC5_CLK_OUTPUT_CFG0_PWR_SHIFT)
108#define VC5_CLK_OUTPUT_CFG0_PWR_18 (0<<VC5_CLK_OUTPUT_CFG0_PWR_SHIFT)
109#define VC5_CLK_OUTPUT_CFG0_PWR_25 (2<<VC5_CLK_OUTPUT_CFG0_PWR_SHIFT)
110#define VC5_CLK_OUTPUT_CFG0_PWR_33 (3<<VC5_CLK_OUTPUT_CFG0_PWR_SHIFT)
111#define VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT 0
112#define VC5_CLK_OUTPUT_CFG0_SLEW_MASK GENMASK(1, VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT)
113#define VC5_CLK_OUTPUT_CFG0_SLEW_80 (0<<VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT)
114#define VC5_CLK_OUTPUT_CFG0_SLEW_85 (1<<VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT)
115#define VC5_CLK_OUTPUT_CFG0_SLEW_90 (2<<VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT)
116#define VC5_CLK_OUTPUT_CFG0_SLEW_100 (3<<VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT)
117#define VC5_CLK_OUTPUT_CFG1_EN_CLKBUF BIT(0)
118
119#define VC5_CLK_OE_SHDN 0x68
120#define VC5_CLK_OS_SHDN 0x69
121
122#define VC5_GLOBAL_REGISTER 0x76
123#define VC5_GLOBAL_REGISTER_GLOBAL_RESET BIT(5)
124
125/* The minimum VCO frequency is 2.5 GHz. The maximum is variant specific. */
126#define VC5_PLL_VCO_MIN 2500000000UL
127
128/* VC5 Input mux settings */
129#define VC5_MUX_IN_XIN BIT(0)
130#define VC5_MUX_IN_CLKIN BIT(1)
131
132/* Maximum number of clk_out supported by this driver */
133#define VC5_MAX_CLK_OUT_NUM 5
134
135/* Maximum number of FODs supported by this driver */
136#define VC5_MAX_FOD_NUM 4
137
138/* flags to describe chip features */
139/* chip has built-in oscilator */
140#define VC5_HAS_INTERNAL_XTAL BIT(0)
141/* chip has PFD requency doubler */
142#define VC5_HAS_PFD_FREQ_DBL BIT(1)
143/* chip has bits to disable FOD sync */
144#define VC5_HAS_BYPASS_SYNC_BIT BIT(2)
145
146/* Supported IDT VC5 models. */
147enum vc5_model {
148 IDT_VC5_5P49V5923,
149 IDT_VC5_5P49V5925,
150 IDT_VC5_5P49V5933,
151 IDT_VC5_5P49V5935,
152 IDT_VC6_5P49V60,
153 IDT_VC6_5P49V6901,
154 IDT_VC6_5P49V6965,
155 IDT_VC6_5P49V6975,
156};
157
158/* Structure to describe features of a particular VC5 model */
159struct vc5_chip_info {
160 const enum vc5_model model;
161 const unsigned int clk_fod_cnt;
162 const unsigned int clk_out_cnt;
163 const u32 flags;
164 const unsigned long vco_max;
165};
166
167struct vc5_driver_data;
168
169struct vc5_hw_data {
170 struct clk_hw hw;
171 struct vc5_driver_data *vc5;
172 u32 div_int;
173 u32 div_frc;
174 unsigned int num;
175};
176
177struct vc5_out_data {
178 struct clk_hw hw;
179 struct vc5_driver_data *vc5;
180 unsigned int num;
181 unsigned int clk_output_cfg0;
182 unsigned int clk_output_cfg0_mask;
183};
184
185struct vc5_driver_data {
186 struct i2c_client *client;
187 struct regmap *regmap;
188 const struct vc5_chip_info *chip_info;
189
190 struct clk *pin_xin;
191 struct clk *pin_clkin;
192 unsigned char clk_mux_ins;
193 struct clk_hw clk_mux;
194 struct clk_hw clk_mul;
195 struct clk_hw clk_pfd;
196 struct vc5_hw_data clk_pll;
197 struct vc5_hw_data clk_fod[VC5_MAX_FOD_NUM];
198 struct vc5_out_data clk_out[VC5_MAX_CLK_OUT_NUM];
199};
200
201/*
202 * VersaClock5 i2c regmap
203 */
204static bool vc5_regmap_is_writeable(struct device *dev, unsigned int reg)
205{
206 /* Factory reserved regs, make them read-only */
207 if (reg <= 0xf)
208 return false;
209
210 /* Factory reserved regs, make them read-only */
211 if (reg == 0x14 || reg == 0x1c || reg == 0x1d)
212 return false;
213
214 return true;
215}
216
217static const struct regmap_config vc5_regmap_config = {
218 .reg_bits = 8,
219 .val_bits = 8,
220 .cache_type = REGCACHE_MAPLE,
221 .max_register = 0x76,
222 .writeable_reg = vc5_regmap_is_writeable,
223};
224
225/*
226 * VersaClock5 input multiplexer between XTAL and CLKIN divider
227 */
228static unsigned char vc5_mux_get_parent(struct clk_hw *hw)
229{
230 struct vc5_driver_data *vc5 =
231 container_of(hw, struct vc5_driver_data, clk_mux);
232 const u8 mask = VC5_PRIM_SRC_SHDN_EN_XTAL | VC5_PRIM_SRC_SHDN_EN_CLKIN;
233 unsigned int src;
234 int ret;
235
236 ret = regmap_read(vc5->regmap, VC5_PRIM_SRC_SHDN, &src);
237 if (ret)
238 return 0;
239
240 src &= mask;
241
242 if (src == VC5_PRIM_SRC_SHDN_EN_XTAL)
243 return 0;
244
245 if (src == VC5_PRIM_SRC_SHDN_EN_CLKIN)
246 return 1;
247
248 dev_warn(&vc5->client->dev,
249 "Invalid clock input configuration (%02x)\n", src);
250 return 0;
251}
252
253static int vc5_mux_set_parent(struct clk_hw *hw, u8 index)
254{
255 struct vc5_driver_data *vc5 =
256 container_of(hw, struct vc5_driver_data, clk_mux);
257 const u8 mask = VC5_PRIM_SRC_SHDN_EN_XTAL | VC5_PRIM_SRC_SHDN_EN_CLKIN;
258 u8 src;
259
260 if ((index > 1) || !vc5->clk_mux_ins)
261 return -EINVAL;
262
263 if (vc5->clk_mux_ins == (VC5_MUX_IN_CLKIN | VC5_MUX_IN_XIN)) {
264 if (index == 0)
265 src = VC5_PRIM_SRC_SHDN_EN_XTAL;
266 if (index == 1)
267 src = VC5_PRIM_SRC_SHDN_EN_CLKIN;
268 } else {
269 if (index != 0)
270 return -EINVAL;
271
272 if (vc5->clk_mux_ins == VC5_MUX_IN_XIN)
273 src = VC5_PRIM_SRC_SHDN_EN_XTAL;
274 else if (vc5->clk_mux_ins == VC5_MUX_IN_CLKIN)
275 src = VC5_PRIM_SRC_SHDN_EN_CLKIN;
276 else /* Invalid; should have been caught by vc5_probe() */
277 return -EINVAL;
278 }
279
280 return regmap_update_bits(vc5->regmap, VC5_PRIM_SRC_SHDN, mask, src);
281}
282
283static const struct clk_ops vc5_mux_ops = {
284 .determine_rate = clk_hw_determine_rate_no_reparent,
285 .set_parent = vc5_mux_set_parent,
286 .get_parent = vc5_mux_get_parent,
287};
288
289static unsigned long vc5_dbl_recalc_rate(struct clk_hw *hw,
290 unsigned long parent_rate)
291{
292 struct vc5_driver_data *vc5 =
293 container_of(hw, struct vc5_driver_data, clk_mul);
294 unsigned int premul;
295 int ret;
296
297 ret = regmap_read(vc5->regmap, VC5_PRIM_SRC_SHDN, &premul);
298 if (ret)
299 return 0;
300
301 if (premul & VC5_PRIM_SRC_SHDN_EN_DOUBLE_XTAL_FREQ)
302 parent_rate *= 2;
303
304 return parent_rate;
305}
306
307static long vc5_dbl_round_rate(struct clk_hw *hw, unsigned long rate,
308 unsigned long *parent_rate)
309{
310 if ((*parent_rate == rate) || ((*parent_rate * 2) == rate))
311 return rate;
312 else
313 return -EINVAL;
314}
315
316static int vc5_dbl_set_rate(struct clk_hw *hw, unsigned long rate,
317 unsigned long parent_rate)
318{
319 struct vc5_driver_data *vc5 =
320 container_of(hw, struct vc5_driver_data, clk_mul);
321 u32 mask;
322
323 if ((parent_rate * 2) == rate)
324 mask = VC5_PRIM_SRC_SHDN_EN_DOUBLE_XTAL_FREQ;
325 else
326 mask = 0;
327
328 return regmap_update_bits(vc5->regmap, VC5_PRIM_SRC_SHDN,
329 VC5_PRIM_SRC_SHDN_EN_DOUBLE_XTAL_FREQ,
330 mask);
331}
332
333static const struct clk_ops vc5_dbl_ops = {
334 .recalc_rate = vc5_dbl_recalc_rate,
335 .round_rate = vc5_dbl_round_rate,
336 .set_rate = vc5_dbl_set_rate,
337};
338
339static unsigned long vc5_pfd_recalc_rate(struct clk_hw *hw,
340 unsigned long parent_rate)
341{
342 struct vc5_driver_data *vc5 =
343 container_of(hw, struct vc5_driver_data, clk_pfd);
344 unsigned int prediv, div;
345 int ret;
346
347 ret = regmap_read(vc5->regmap, VC5_VCO_CTRL_AND_PREDIV, &prediv);
348 if (ret)
349 return 0;
350
351 /* The bypass_prediv is set, PLL fed from Ref_in directly. */
352 if (prediv & VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV)
353 return parent_rate;
354
355 ret = regmap_read(vc5->regmap, VC5_REF_DIVIDER, &div);
356 if (ret)
357 return 0;
358
359 /* The Sel_prediv2 is set, PLL fed from prediv2 (Ref_in / 2) */
360 if (div & VC5_REF_DIVIDER_SEL_PREDIV2)
361 return parent_rate / 2;
362 else
363 return parent_rate / VC5_REF_DIVIDER_REF_DIV(div);
364}
365
366static long vc5_pfd_round_rate(struct clk_hw *hw, unsigned long rate,
367 unsigned long *parent_rate)
368{
369 unsigned long idiv;
370
371 /* PLL cannot operate with input clock above 50 MHz. */
372 if (rate > 50000000)
373 return -EINVAL;
374
375 /* CLKIN within range of PLL input, feed directly to PLL. */
376 if (*parent_rate <= 50000000)
377 return *parent_rate;
378
379 idiv = DIV_ROUND_UP(*parent_rate, rate);
380 if (idiv > 127)
381 return -EINVAL;
382
383 return *parent_rate / idiv;
384}
385
386static int vc5_pfd_set_rate(struct clk_hw *hw, unsigned long rate,
387 unsigned long parent_rate)
388{
389 struct vc5_driver_data *vc5 =
390 container_of(hw, struct vc5_driver_data, clk_pfd);
391 unsigned long idiv;
392 int ret;
393 u8 div;
394
395 /* CLKIN within range of PLL input, feed directly to PLL. */
396 if (parent_rate <= 50000000) {
397 ret = regmap_set_bits(vc5->regmap, VC5_VCO_CTRL_AND_PREDIV,
398 VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV);
399 if (ret)
400 return ret;
401
402 return regmap_update_bits(vc5->regmap, VC5_REF_DIVIDER, 0xff, 0x00);
403 }
404
405 idiv = DIV_ROUND_UP(parent_rate, rate);
406
407 /* We have dedicated div-2 predivider. */
408 if (idiv == 2)
409 div = VC5_REF_DIVIDER_SEL_PREDIV2;
410 else
411 div = VC5_REF_DIVIDER_REF_DIV(idiv);
412
413 ret = regmap_update_bits(vc5->regmap, VC5_REF_DIVIDER, 0xff, div);
414 if (ret)
415 return ret;
416
417 return regmap_clear_bits(vc5->regmap, VC5_VCO_CTRL_AND_PREDIV,
418 VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV);
419}
420
421static const struct clk_ops vc5_pfd_ops = {
422 .recalc_rate = vc5_pfd_recalc_rate,
423 .round_rate = vc5_pfd_round_rate,
424 .set_rate = vc5_pfd_set_rate,
425};
426
427/*
428 * VersaClock5 PLL/VCO
429 */
430static unsigned long vc5_pll_recalc_rate(struct clk_hw *hw,
431 unsigned long parent_rate)
432{
433 struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
434 struct vc5_driver_data *vc5 = hwdata->vc5;
435 u32 div_int, div_frc;
436 u8 fb[5];
437
438 regmap_bulk_read(vc5->regmap, VC5_FEEDBACK_INT_DIV, fb, 5);
439
440 div_int = (fb[0] << 4) | (fb[1] >> 4);
441 div_frc = (fb[2] << 16) | (fb[3] << 8) | fb[4];
442
443 /* The PLL divider has 12 integer bits and 24 fractional bits */
444 return (parent_rate * div_int) + ((parent_rate * div_frc) >> 24);
445}
446
447static long vc5_pll_round_rate(struct clk_hw *hw, unsigned long rate,
448 unsigned long *parent_rate)
449{
450 struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
451 struct vc5_driver_data *vc5 = hwdata->vc5;
452 u32 div_int;
453 u64 div_frc;
454
455 rate = clamp(rate, VC5_PLL_VCO_MIN, vc5->chip_info->vco_max);
456
457 /* Determine integer part, which is 12 bit wide */
458 div_int = rate / *parent_rate;
459 if (div_int > 0xfff)
460 rate = *parent_rate * 0xfff;
461
462 /* Determine best fractional part, which is 24 bit wide */
463 div_frc = rate % *parent_rate;
464 div_frc *= BIT(24) - 1;
465 do_div(div_frc, *parent_rate);
466
467 hwdata->div_int = div_int;
468 hwdata->div_frc = (u32)div_frc;
469
470 return (*parent_rate * div_int) + ((*parent_rate * div_frc) >> 24);
471}
472
473static int vc5_pll_set_rate(struct clk_hw *hw, unsigned long rate,
474 unsigned long parent_rate)
475{
476 struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
477 struct vc5_driver_data *vc5 = hwdata->vc5;
478 u8 fb[5];
479
480 fb[0] = hwdata->div_int >> 4;
481 fb[1] = hwdata->div_int << 4;
482 fb[2] = hwdata->div_frc >> 16;
483 fb[3] = hwdata->div_frc >> 8;
484 fb[4] = hwdata->div_frc;
485
486 return regmap_bulk_write(vc5->regmap, VC5_FEEDBACK_INT_DIV, fb, 5);
487}
488
489static const struct clk_ops vc5_pll_ops = {
490 .recalc_rate = vc5_pll_recalc_rate,
491 .round_rate = vc5_pll_round_rate,
492 .set_rate = vc5_pll_set_rate,
493};
494
495static unsigned long vc5_fod_recalc_rate(struct clk_hw *hw,
496 unsigned long parent_rate)
497{
498 struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
499 struct vc5_driver_data *vc5 = hwdata->vc5;
500 /* VCO frequency is divided by two before entering FOD */
501 u32 f_in = parent_rate / 2;
502 u32 div_int, div_frc;
503 u8 od_int[2];
504 u8 od_frc[4];
505
506 regmap_bulk_read(vc5->regmap, VC5_OUT_DIV_INT(hwdata->num, 0),
507 od_int, 2);
508 regmap_bulk_read(vc5->regmap, VC5_OUT_DIV_FRAC(hwdata->num, 0),
509 od_frc, 4);
510
511 div_int = (od_int[0] << 4) | (od_int[1] >> 4);
512 div_frc = (od_frc[0] << 22) | (od_frc[1] << 14) |
513 (od_frc[2] << 6) | (od_frc[3] >> 2);
514
515 /* Avoid division by zero if the output is not configured. */
516 if (div_int == 0 && div_frc == 0)
517 return 0;
518
519 /* The PLL divider has 12 integer bits and 30 fractional bits */
520 return div64_u64((u64)f_in << 24ULL, ((u64)div_int << 24ULL) + div_frc);
521}
522
523static long vc5_fod_round_rate(struct clk_hw *hw, unsigned long rate,
524 unsigned long *parent_rate)
525{
526 struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
527 /* VCO frequency is divided by two before entering FOD */
528 u32 f_in = *parent_rate / 2;
529 u32 div_int;
530 u64 div_frc;
531
532 /* Determine integer part, which is 12 bit wide */
533 div_int = f_in / rate;
534 /*
535 * WARNING: The clock chip does not output signal if the integer part
536 * of the divider is 0xfff and fractional part is non-zero.
537 * Clamp the divider at 0xffe to keep the code simple.
538 */
539 if (div_int > 0xffe) {
540 div_int = 0xffe;
541 rate = f_in / div_int;
542 }
543
544 /* Determine best fractional part, which is 30 bit wide */
545 div_frc = f_in % rate;
546 div_frc <<= 24;
547 do_div(div_frc, rate);
548
549 hwdata->div_int = div_int;
550 hwdata->div_frc = (u32)div_frc;
551
552 return div64_u64((u64)f_in << 24ULL, ((u64)div_int << 24ULL) + div_frc);
553}
554
555static int vc5_fod_set_rate(struct clk_hw *hw, unsigned long rate,
556 unsigned long parent_rate)
557{
558 struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
559 struct vc5_driver_data *vc5 = hwdata->vc5;
560 u8 data[14] = {
561 hwdata->div_frc >> 22, hwdata->div_frc >> 14,
562 hwdata->div_frc >> 6, hwdata->div_frc << 2,
563 0, 0, 0, 0, 0,
564 0, 0,
565 hwdata->div_int >> 4, hwdata->div_int << 4,
566 0
567 };
568 int ret;
569
570 ret = regmap_bulk_write(vc5->regmap, VC5_OUT_DIV_FRAC(hwdata->num, 0),
571 data, 14);
572 if (ret)
573 return ret;
574
575 /*
576 * Toggle magic bit in undocumented register for unknown reason.
577 * This is what the IDT timing commander tool does and the chip
578 * datasheet somewhat implies this is needed, but the register
579 * and the bit is not documented.
580 */
581 ret = regmap_clear_bits(vc5->regmap, VC5_GLOBAL_REGISTER,
582 VC5_GLOBAL_REGISTER_GLOBAL_RESET);
583 if (ret)
584 return ret;
585
586 return regmap_set_bits(vc5->regmap, VC5_GLOBAL_REGISTER,
587 VC5_GLOBAL_REGISTER_GLOBAL_RESET);
588}
589
590static const struct clk_ops vc5_fod_ops = {
591 .recalc_rate = vc5_fod_recalc_rate,
592 .round_rate = vc5_fod_round_rate,
593 .set_rate = vc5_fod_set_rate,
594};
595
596static int vc5_clk_out_prepare(struct clk_hw *hw)
597{
598 struct vc5_out_data *hwdata = container_of(hw, struct vc5_out_data, hw);
599 struct vc5_driver_data *vc5 = hwdata->vc5;
600 const u8 mask = VC5_OUT_DIV_CONTROL_SELB_NORM |
601 VC5_OUT_DIV_CONTROL_SEL_EXT |
602 VC5_OUT_DIV_CONTROL_EN_FOD;
603 unsigned int src;
604 int ret;
605
606 /*
607 * When enabling a FOD, all currently enabled FODs are briefly
608 * stopped in order to synchronize all of them. This causes a clock
609 * disruption to any unrelated chips that might be already using
610 * other clock outputs. Bypass the sync feature to avoid the issue,
611 * which is possible on the VersaClock 6E family via reserved
612 * registers.
613 */
614 if (vc5->chip_info->flags & VC5_HAS_BYPASS_SYNC_BIT) {
615 ret = regmap_set_bits(vc5->regmap,
616 VC5_RESERVED_X0(hwdata->num),
617 VC5_RESERVED_X0_BYPASS_SYNC);
618 if (ret)
619 return ret;
620 }
621
622 /*
623 * If the input mux is disabled, enable it first and
624 * select source from matching FOD.
625 */
626 ret = regmap_read(vc5->regmap, VC5_OUT_DIV_CONTROL(hwdata->num), &src);
627 if (ret)
628 return ret;
629
630 if ((src & mask) == 0) {
631 src = VC5_OUT_DIV_CONTROL_RESET | VC5_OUT_DIV_CONTROL_EN_FOD;
632 ret = regmap_update_bits(vc5->regmap,
633 VC5_OUT_DIV_CONTROL(hwdata->num),
634 mask | VC5_OUT_DIV_CONTROL_RESET, src);
635 if (ret)
636 return ret;
637 }
638
639 /* Enable the clock buffer */
640 ret = regmap_set_bits(vc5->regmap, VC5_CLK_OUTPUT_CFG(hwdata->num, 1),
641 VC5_CLK_OUTPUT_CFG1_EN_CLKBUF);
642 if (ret)
643 return ret;
644
645 if (hwdata->clk_output_cfg0_mask) {
646 dev_dbg(&vc5->client->dev, "Update output %d mask 0x%0X val 0x%0X\n",
647 hwdata->num, hwdata->clk_output_cfg0_mask,
648 hwdata->clk_output_cfg0);
649
650 ret = regmap_update_bits(vc5->regmap,
651 VC5_CLK_OUTPUT_CFG(hwdata->num, 0),
652 hwdata->clk_output_cfg0_mask,
653 hwdata->clk_output_cfg0);
654 if (ret)
655 return ret;
656 }
657
658 return 0;
659}
660
661static void vc5_clk_out_unprepare(struct clk_hw *hw)
662{
663 struct vc5_out_data *hwdata = container_of(hw, struct vc5_out_data, hw);
664 struct vc5_driver_data *vc5 = hwdata->vc5;
665
666 /* Disable the clock buffer */
667 regmap_clear_bits(vc5->regmap, VC5_CLK_OUTPUT_CFG(hwdata->num, 1),
668 VC5_CLK_OUTPUT_CFG1_EN_CLKBUF);
669}
670
671static unsigned char vc5_clk_out_get_parent(struct clk_hw *hw)
672{
673 struct vc5_out_data *hwdata = container_of(hw, struct vc5_out_data, hw);
674 struct vc5_driver_data *vc5 = hwdata->vc5;
675 const u8 mask = VC5_OUT_DIV_CONTROL_SELB_NORM |
676 VC5_OUT_DIV_CONTROL_SEL_EXT |
677 VC5_OUT_DIV_CONTROL_EN_FOD;
678 const u8 fodclkmask = VC5_OUT_DIV_CONTROL_SELB_NORM |
679 VC5_OUT_DIV_CONTROL_EN_FOD;
680 const u8 extclk = VC5_OUT_DIV_CONTROL_SELB_NORM |
681 VC5_OUT_DIV_CONTROL_SEL_EXT;
682 unsigned int src;
683 int ret;
684
685 ret = regmap_read(vc5->regmap, VC5_OUT_DIV_CONTROL(hwdata->num), &src);
686 if (ret)
687 return 0;
688
689 src &= mask;
690
691 if (src == 0) /* Input mux set to DISABLED */
692 return 0;
693
694 if ((src & fodclkmask) == VC5_OUT_DIV_CONTROL_EN_FOD)
695 return 0;
696
697 if (src == extclk)
698 return 1;
699
700 dev_warn(&vc5->client->dev,
701 "Invalid clock output configuration (%02x)\n", src);
702 return 0;
703}
704
705static int vc5_clk_out_set_parent(struct clk_hw *hw, u8 index)
706{
707 struct vc5_out_data *hwdata = container_of(hw, struct vc5_out_data, hw);
708 struct vc5_driver_data *vc5 = hwdata->vc5;
709 const u8 mask = VC5_OUT_DIV_CONTROL_RESET |
710 VC5_OUT_DIV_CONTROL_SELB_NORM |
711 VC5_OUT_DIV_CONTROL_SEL_EXT |
712 VC5_OUT_DIV_CONTROL_EN_FOD;
713 const u8 extclk = VC5_OUT_DIV_CONTROL_SELB_NORM |
714 VC5_OUT_DIV_CONTROL_SEL_EXT;
715 u8 src = VC5_OUT_DIV_CONTROL_RESET;
716
717 if (index == 0)
718 src |= VC5_OUT_DIV_CONTROL_EN_FOD;
719 else
720 src |= extclk;
721
722 return regmap_update_bits(vc5->regmap, VC5_OUT_DIV_CONTROL(hwdata->num),
723 mask, src);
724}
725
726static const struct clk_ops vc5_clk_out_ops = {
727 .prepare = vc5_clk_out_prepare,
728 .unprepare = vc5_clk_out_unprepare,
729 .determine_rate = clk_hw_determine_rate_no_reparent,
730 .set_parent = vc5_clk_out_set_parent,
731 .get_parent = vc5_clk_out_get_parent,
732};
733
734static struct clk_hw *vc5_of_clk_get(struct of_phandle_args *clkspec,
735 void *data)
736{
737 struct vc5_driver_data *vc5 = data;
738 unsigned int idx = clkspec->args[0];
739
740 if (idx >= vc5->chip_info->clk_out_cnt)
741 return ERR_PTR(-EINVAL);
742
743 return &vc5->clk_out[idx].hw;
744}
745
746static int vc5_map_index_to_output(const enum vc5_model model,
747 const unsigned int n)
748{
749 switch (model) {
750 case IDT_VC5_5P49V5933:
751 return (n == 0) ? 0 : 3;
752 case IDT_VC5_5P49V5923:
753 case IDT_VC5_5P49V5925:
754 case IDT_VC5_5P49V5935:
755 case IDT_VC6_5P49V6901:
756 case IDT_VC6_5P49V6965:
757 case IDT_VC6_5P49V6975:
758 default:
759 return n;
760 }
761}
762
763static int vc5_update_mode(struct device_node *np_output,
764 struct vc5_out_data *clk_out)
765{
766 u32 value;
767
768 if (!of_property_read_u32(np_output, "idt,mode", &value)) {
769 clk_out->clk_output_cfg0_mask |= VC5_CLK_OUTPUT_CFG0_CFG_MASK;
770 switch (value) {
771 case VC5_CLK_OUTPUT_CFG0_CFG_LVPECL:
772 case VC5_CLK_OUTPUT_CFG0_CFG_CMOS:
773 case VC5_CLK_OUTPUT_CFG0_CFG_HCSL33:
774 case VC5_CLK_OUTPUT_CFG0_CFG_LVDS:
775 case VC5_CLK_OUTPUT_CFG0_CFG_CMOS2:
776 case VC5_CLK_OUTPUT_CFG0_CFG_CMOSD:
777 case VC5_CLK_OUTPUT_CFG0_CFG_HCSL25:
778 clk_out->clk_output_cfg0 |=
779 value << VC5_CLK_OUTPUT_CFG0_CFG_SHIFT;
780 break;
781 default:
782 return -EINVAL;
783 }
784 }
785 return 0;
786}
787
788static int vc5_update_power(struct device_node *np_output,
789 struct vc5_out_data *clk_out)
790{
791 u32 value;
792
793 if (!of_property_read_u32(np_output, "idt,voltage-microvolt",
794 &value)) {
795 clk_out->clk_output_cfg0_mask |= VC5_CLK_OUTPUT_CFG0_PWR_MASK;
796 switch (value) {
797 case 1800000:
798 clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_PWR_18;
799 break;
800 case 2500000:
801 clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_PWR_25;
802 break;
803 case 3300000:
804 clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_PWR_33;
805 break;
806 default:
807 return -EINVAL;
808 }
809 }
810 return 0;
811}
812
813static int vc5_map_cap_value(u32 femtofarads)
814{
815 int mapped_value;
816
817 /*
818 * The datasheet explicitly states 9000 - 25000 with 0.5pF
819 * steps, but the Programmer's guide shows the steps are 0.430pF.
820 * After getting feedback from Renesas, the .5pF steps were the
821 * goal, but 430nF was the actual values.
822 * Because of this, the actual range goes to 22760 instead of 25000
823 */
824 if (femtofarads < 9000 || femtofarads > 22760)
825 return -EINVAL;
826
827 /*
828 * The Programmer's guide shows XTAL[5:0] but in reality,
829 * XTAL[0] and XTAL[1] are both LSB which makes the math
830 * strange. With clarfication from Renesas, setting the
831 * values should be simpler by ignoring XTAL[0]
832 */
833 mapped_value = DIV_ROUND_CLOSEST(femtofarads - 9000, 430);
834
835 /*
836 * Since the calculation ignores XTAL[0], there is one
837 * special case where mapped_value = 32. In reality, this means
838 * the real mapped value should be 111111b. In other cases,
839 * the mapped_value needs to be shifted 1 to the left.
840 */
841 if (mapped_value > 31)
842 mapped_value = 0x3f;
843 else
844 mapped_value <<= 1;
845
846 return mapped_value;
847}
848static int vc5_update_cap_load(struct device_node *node, struct vc5_driver_data *vc5)
849{
850 u32 value;
851 int mapped_value;
852 int ret;
853
854 if (of_property_read_u32(node, "idt,xtal-load-femtofarads", &value))
855 return 0;
856
857 mapped_value = vc5_map_cap_value(value);
858 if (mapped_value < 0)
859 return mapped_value;
860
861 /*
862 * The mapped_value is really the high 6 bits of
863 * VC5_XTAL_X1_LOAD_CAP and VC5_XTAL_X2_LOAD_CAP, so
864 * shift the value 2 places.
865 */
866 ret = regmap_update_bits(vc5->regmap, VC5_XTAL_X1_LOAD_CAP, ~0x03,
867 mapped_value << 2);
868 if (ret)
869 return ret;
870
871 return regmap_update_bits(vc5->regmap, VC5_XTAL_X2_LOAD_CAP, ~0x03,
872 mapped_value << 2);
873}
874
875static int vc5_update_slew(struct device_node *np_output,
876 struct vc5_out_data *clk_out)
877{
878 u32 value;
879
880 if (!of_property_read_u32(np_output, "idt,slew-percent", &value)) {
881 clk_out->clk_output_cfg0_mask |= VC5_CLK_OUTPUT_CFG0_SLEW_MASK;
882 switch (value) {
883 case 80:
884 clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_SLEW_80;
885 break;
886 case 85:
887 clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_SLEW_85;
888 break;
889 case 90:
890 clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_SLEW_90;
891 break;
892 case 100:
893 clk_out->clk_output_cfg0 |=
894 VC5_CLK_OUTPUT_CFG0_SLEW_100;
895 break;
896 default:
897 return -EINVAL;
898 }
899 }
900 return 0;
901}
902
903static int vc5_get_output_config(struct i2c_client *client,
904 struct vc5_out_data *clk_out)
905{
906 struct device_node *np_output;
907 char *child_name;
908 int ret = 0;
909
910 child_name = kasprintf(GFP_KERNEL, "OUT%d", clk_out->num + 1);
911 if (!child_name)
912 return -ENOMEM;
913
914 np_output = of_get_child_by_name(client->dev.of_node, child_name);
915 kfree(child_name);
916 if (!np_output)
917 return 0;
918
919 ret = vc5_update_mode(np_output, clk_out);
920 if (ret)
921 goto output_error;
922
923 ret = vc5_update_power(np_output, clk_out);
924 if (ret)
925 goto output_error;
926
927 ret = vc5_update_slew(np_output, clk_out);
928
929output_error:
930 if (ret) {
931 dev_err(&client->dev,
932 "Invalid clock output configuration OUT%d\n",
933 clk_out->num + 1);
934 }
935
936 of_node_put(np_output);
937
938 return ret;
939}
940
941static const struct of_device_id clk_vc5_of_match[];
942
943static int vc5_probe(struct i2c_client *client)
944{
945 unsigned int oe, sd, src_mask = 0, src_val = 0;
946 struct vc5_driver_data *vc5;
947 struct clk_init_data init;
948 const char *parent_names[2];
949 unsigned int n, idx = 0;
950 int ret;
951
952 vc5 = devm_kzalloc(&client->dev, sizeof(*vc5), GFP_KERNEL);
953 if (!vc5)
954 return -ENOMEM;
955
956 i2c_set_clientdata(client, vc5);
957 vc5->client = client;
958 vc5->chip_info = i2c_get_match_data(client);
959
960 vc5->pin_xin = devm_clk_get(&client->dev, "xin");
961 if (PTR_ERR(vc5->pin_xin) == -EPROBE_DEFER)
962 return -EPROBE_DEFER;
963
964 vc5->pin_clkin = devm_clk_get(&client->dev, "clkin");
965 if (PTR_ERR(vc5->pin_clkin) == -EPROBE_DEFER)
966 return -EPROBE_DEFER;
967
968 vc5->regmap = devm_regmap_init_i2c(client, &vc5_regmap_config);
969 if (IS_ERR(vc5->regmap))
970 return dev_err_probe(&client->dev, PTR_ERR(vc5->regmap),
971 "failed to allocate register map\n");
972
973 ret = of_property_read_u32(client->dev.of_node, "idt,shutdown", &sd);
974 if (!ret) {
975 src_mask |= VC5_PRIM_SRC_SHDN_EN_GBL_SHDN;
976 if (sd)
977 src_val |= VC5_PRIM_SRC_SHDN_EN_GBL_SHDN;
978 } else if (ret != -EINVAL) {
979 return dev_err_probe(&client->dev, ret,
980 "could not read idt,shutdown\n");
981 }
982
983 ret = of_property_read_u32(client->dev.of_node,
984 "idt,output-enable-active", &oe);
985 if (!ret) {
986 src_mask |= VC5_PRIM_SRC_SHDN_SP;
987 if (oe)
988 src_val |= VC5_PRIM_SRC_SHDN_SP;
989 } else if (ret != -EINVAL) {
990 return dev_err_probe(&client->dev, ret,
991 "could not read idt,output-enable-active\n");
992 }
993
994 ret = regmap_update_bits(vc5->regmap, VC5_PRIM_SRC_SHDN, src_mask,
995 src_val);
996 if (ret)
997 return ret;
998
999 /* Register clock input mux */
1000 memset(&init, 0, sizeof(init));
1001
1002 if (!IS_ERR(vc5->pin_xin)) {
1003 vc5->clk_mux_ins |= VC5_MUX_IN_XIN;
1004 parent_names[init.num_parents++] = __clk_get_name(vc5->pin_xin);
1005 } else if (vc5->chip_info->flags & VC5_HAS_INTERNAL_XTAL) {
1006 vc5->pin_xin = clk_register_fixed_rate(&client->dev,
1007 "internal-xtal", NULL,
1008 0, 25000000);
1009 if (IS_ERR(vc5->pin_xin))
1010 return PTR_ERR(vc5->pin_xin);
1011 vc5->clk_mux_ins |= VC5_MUX_IN_XIN;
1012 parent_names[init.num_parents++] = __clk_get_name(vc5->pin_xin);
1013 }
1014
1015 if (!IS_ERR(vc5->pin_clkin)) {
1016 vc5->clk_mux_ins |= VC5_MUX_IN_CLKIN;
1017 parent_names[init.num_parents++] =
1018 __clk_get_name(vc5->pin_clkin);
1019 }
1020
1021 if (!init.num_parents)
1022 return dev_err_probe(&client->dev, -EINVAL,
1023 "no input clock specified!\n");
1024
1025 /* Configure Optional Loading Capacitance for external XTAL */
1026 if (!(vc5->chip_info->flags & VC5_HAS_INTERNAL_XTAL)) {
1027 ret = vc5_update_cap_load(client->dev.of_node, vc5);
1028 if (ret)
1029 goto err_clk_register;
1030 }
1031
1032 init.name = kasprintf(GFP_KERNEL, "%pOFn.mux", client->dev.of_node);
1033 if (!init.name) {
1034 ret = -ENOMEM;
1035 goto err_clk;
1036 }
1037
1038 init.ops = &vc5_mux_ops;
1039 init.flags = 0;
1040 init.parent_names = parent_names;
1041 vc5->clk_mux.init = &init;
1042 ret = devm_clk_hw_register(&client->dev, &vc5->clk_mux);
1043 if (ret)
1044 goto err_clk_register;
1045 kfree(init.name); /* clock framework made a copy of the name */
1046
1047 if (vc5->chip_info->flags & VC5_HAS_PFD_FREQ_DBL) {
1048 /* Register frequency doubler */
1049 memset(&init, 0, sizeof(init));
1050 init.name = kasprintf(GFP_KERNEL, "%pOFn.dbl",
1051 client->dev.of_node);
1052 if (!init.name) {
1053 ret = -ENOMEM;
1054 goto err_clk;
1055 }
1056 init.ops = &vc5_dbl_ops;
1057 init.flags = CLK_SET_RATE_PARENT;
1058 init.parent_names = parent_names;
1059 parent_names[0] = clk_hw_get_name(&vc5->clk_mux);
1060 init.num_parents = 1;
1061 vc5->clk_mul.init = &init;
1062 ret = devm_clk_hw_register(&client->dev, &vc5->clk_mul);
1063 if (ret)
1064 goto err_clk_register;
1065 kfree(init.name); /* clock framework made a copy of the name */
1066 }
1067
1068 /* Register PFD */
1069 memset(&init, 0, sizeof(init));
1070 init.name = kasprintf(GFP_KERNEL, "%pOFn.pfd", client->dev.of_node);
1071 if (!init.name) {
1072 ret = -ENOMEM;
1073 goto err_clk;
1074 }
1075 init.ops = &vc5_pfd_ops;
1076 init.flags = CLK_SET_RATE_PARENT;
1077 init.parent_names = parent_names;
1078 if (vc5->chip_info->flags & VC5_HAS_PFD_FREQ_DBL)
1079 parent_names[0] = clk_hw_get_name(&vc5->clk_mul);
1080 else
1081 parent_names[0] = clk_hw_get_name(&vc5->clk_mux);
1082 init.num_parents = 1;
1083 vc5->clk_pfd.init = &init;
1084 ret = devm_clk_hw_register(&client->dev, &vc5->clk_pfd);
1085 if (ret)
1086 goto err_clk_register;
1087 kfree(init.name); /* clock framework made a copy of the name */
1088
1089 /* Register PLL */
1090 memset(&init, 0, sizeof(init));
1091 init.name = kasprintf(GFP_KERNEL, "%pOFn.pll", client->dev.of_node);
1092 if (!init.name) {
1093 ret = -ENOMEM;
1094 goto err_clk;
1095 }
1096 init.ops = &vc5_pll_ops;
1097 init.flags = CLK_SET_RATE_PARENT;
1098 init.parent_names = parent_names;
1099 parent_names[0] = clk_hw_get_name(&vc5->clk_pfd);
1100 init.num_parents = 1;
1101 vc5->clk_pll.num = 0;
1102 vc5->clk_pll.vc5 = vc5;
1103 vc5->clk_pll.hw.init = &init;
1104 ret = devm_clk_hw_register(&client->dev, &vc5->clk_pll.hw);
1105 if (ret)
1106 goto err_clk_register;
1107 kfree(init.name); /* clock framework made a copy of the name */
1108
1109 /* Register FODs */
1110 for (n = 0; n < vc5->chip_info->clk_fod_cnt; n++) {
1111 idx = vc5_map_index_to_output(vc5->chip_info->model, n);
1112 memset(&init, 0, sizeof(init));
1113 init.name = kasprintf(GFP_KERNEL, "%pOFn.fod%d",
1114 client->dev.of_node, idx);
1115 if (!init.name) {
1116 ret = -ENOMEM;
1117 goto err_clk;
1118 }
1119 init.ops = &vc5_fod_ops;
1120 init.flags = CLK_SET_RATE_PARENT;
1121 init.parent_names = parent_names;
1122 parent_names[0] = clk_hw_get_name(&vc5->clk_pll.hw);
1123 init.num_parents = 1;
1124 vc5->clk_fod[n].num = idx;
1125 vc5->clk_fod[n].vc5 = vc5;
1126 vc5->clk_fod[n].hw.init = &init;
1127 ret = devm_clk_hw_register(&client->dev, &vc5->clk_fod[n].hw);
1128 if (ret)
1129 goto err_clk_register;
1130 kfree(init.name); /* clock framework made a copy of the name */
1131 }
1132
1133 /* Register MUX-connected OUT0_I2C_SELB output */
1134 memset(&init, 0, sizeof(init));
1135 init.name = kasprintf(GFP_KERNEL, "%pOFn.out0_sel_i2cb",
1136 client->dev.of_node);
1137 if (!init.name) {
1138 ret = -ENOMEM;
1139 goto err_clk;
1140 }
1141 init.ops = &vc5_clk_out_ops;
1142 init.flags = CLK_SET_RATE_PARENT;
1143 init.parent_names = parent_names;
1144 parent_names[0] = clk_hw_get_name(&vc5->clk_mux);
1145 init.num_parents = 1;
1146 vc5->clk_out[0].num = idx;
1147 vc5->clk_out[0].vc5 = vc5;
1148 vc5->clk_out[0].hw.init = &init;
1149 ret = devm_clk_hw_register(&client->dev, &vc5->clk_out[0].hw);
1150 if (ret)
1151 goto err_clk_register;
1152 kfree(init.name); /* clock framework made a copy of the name */
1153
1154 /* Register FOD-connected OUTx outputs */
1155 for (n = 1; n < vc5->chip_info->clk_out_cnt; n++) {
1156 idx = vc5_map_index_to_output(vc5->chip_info->model, n - 1);
1157 parent_names[0] = clk_hw_get_name(&vc5->clk_fod[idx].hw);
1158 if (n == 1)
1159 parent_names[1] = clk_hw_get_name(&vc5->clk_mux);
1160 else
1161 parent_names[1] =
1162 clk_hw_get_name(&vc5->clk_out[n - 1].hw);
1163
1164 memset(&init, 0, sizeof(init));
1165 init.name = kasprintf(GFP_KERNEL, "%pOFn.out%d",
1166 client->dev.of_node, idx + 1);
1167 if (!init.name) {
1168 ret = -ENOMEM;
1169 goto err_clk;
1170 }
1171 init.ops = &vc5_clk_out_ops;
1172 init.flags = CLK_SET_RATE_PARENT;
1173 init.parent_names = parent_names;
1174 init.num_parents = 2;
1175 vc5->clk_out[n].num = idx;
1176 vc5->clk_out[n].vc5 = vc5;
1177 vc5->clk_out[n].hw.init = &init;
1178 ret = devm_clk_hw_register(&client->dev, &vc5->clk_out[n].hw);
1179 if (ret)
1180 goto err_clk_register;
1181 kfree(init.name); /* clock framework made a copy of the name */
1182
1183 /* Fetch Clock Output configuration from DT (if specified) */
1184 ret = vc5_get_output_config(client, &vc5->clk_out[n]);
1185 if (ret)
1186 goto err_clk;
1187 }
1188
1189 ret = of_clk_add_hw_provider(client->dev.of_node, vc5_of_clk_get, vc5);
1190 if (ret) {
1191 dev_err_probe(&client->dev, ret,
1192 "unable to add clk provider\n");
1193 goto err_clk;
1194 }
1195
1196 return 0;
1197
1198err_clk_register:
1199 dev_err_probe(&client->dev, ret,
1200 "unable to register %s\n", init.name);
1201 kfree(init.name); /* clock framework made a copy of the name */
1202err_clk:
1203 if (vc5->chip_info->flags & VC5_HAS_INTERNAL_XTAL)
1204 clk_unregister_fixed_rate(vc5->pin_xin);
1205 return ret;
1206}
1207
1208static void vc5_remove(struct i2c_client *client)
1209{
1210 struct vc5_driver_data *vc5 = i2c_get_clientdata(client);
1211
1212 of_clk_del_provider(client->dev.of_node);
1213
1214 if (vc5->chip_info->flags & VC5_HAS_INTERNAL_XTAL)
1215 clk_unregister_fixed_rate(vc5->pin_xin);
1216}
1217
1218static int __maybe_unused vc5_suspend(struct device *dev)
1219{
1220 struct vc5_driver_data *vc5 = dev_get_drvdata(dev);
1221
1222 regcache_cache_only(vc5->regmap, true);
1223 regcache_mark_dirty(vc5->regmap);
1224
1225 return 0;
1226}
1227
1228static int __maybe_unused vc5_resume(struct device *dev)
1229{
1230 struct vc5_driver_data *vc5 = dev_get_drvdata(dev);
1231 int ret;
1232
1233 regcache_cache_only(vc5->regmap, false);
1234 ret = regcache_sync(vc5->regmap);
1235 if (ret)
1236 dev_err(dev, "Failed to restore register map: %d\n", ret);
1237 return ret;
1238}
1239
1240static const struct vc5_chip_info idt_5p49v5923_info = {
1241 .model = IDT_VC5_5P49V5923,
1242 .clk_fod_cnt = 2,
1243 .clk_out_cnt = 3,
1244 .flags = 0,
1245 .vco_max = 3000000000UL,
1246};
1247
1248static const struct vc5_chip_info idt_5p49v5925_info = {
1249 .model = IDT_VC5_5P49V5925,
1250 .clk_fod_cnt = 4,
1251 .clk_out_cnt = 5,
1252 .flags = 0,
1253 .vco_max = 3000000000UL,
1254};
1255
1256static const struct vc5_chip_info idt_5p49v5933_info = {
1257 .model = IDT_VC5_5P49V5933,
1258 .clk_fod_cnt = 2,
1259 .clk_out_cnt = 3,
1260 .flags = VC5_HAS_INTERNAL_XTAL,
1261 .vco_max = 3000000000UL,
1262};
1263
1264static const struct vc5_chip_info idt_5p49v5935_info = {
1265 .model = IDT_VC5_5P49V5935,
1266 .clk_fod_cnt = 4,
1267 .clk_out_cnt = 5,
1268 .flags = VC5_HAS_INTERNAL_XTAL,
1269 .vco_max = 3000000000UL,
1270};
1271
1272static const struct vc5_chip_info idt_5p49v60_info = {
1273 .model = IDT_VC6_5P49V60,
1274 .clk_fod_cnt = 4,
1275 .clk_out_cnt = 5,
1276 .flags = VC5_HAS_PFD_FREQ_DBL | VC5_HAS_BYPASS_SYNC_BIT,
1277 .vco_max = 2700000000UL,
1278};
1279
1280static const struct vc5_chip_info idt_5p49v6901_info = {
1281 .model = IDT_VC6_5P49V6901,
1282 .clk_fod_cnt = 4,
1283 .clk_out_cnt = 5,
1284 .flags = VC5_HAS_PFD_FREQ_DBL | VC5_HAS_BYPASS_SYNC_BIT,
1285 .vco_max = 3000000000UL,
1286};
1287
1288static const struct vc5_chip_info idt_5p49v6965_info = {
1289 .model = IDT_VC6_5P49V6965,
1290 .clk_fod_cnt = 4,
1291 .clk_out_cnt = 5,
1292 .flags = VC5_HAS_BYPASS_SYNC_BIT,
1293 .vco_max = 3000000000UL,
1294};
1295
1296static const struct vc5_chip_info idt_5p49v6975_info = {
1297 .model = IDT_VC6_5P49V6975,
1298 .clk_fod_cnt = 4,
1299 .clk_out_cnt = 5,
1300 .flags = VC5_HAS_BYPASS_SYNC_BIT | VC5_HAS_INTERNAL_XTAL,
1301 .vco_max = 3000000000UL,
1302};
1303
1304static const struct i2c_device_id vc5_id[] = {
1305 { "5p49v5923", .driver_data = (kernel_ulong_t)&idt_5p49v5923_info },
1306 { "5p49v5925", .driver_data = (kernel_ulong_t)&idt_5p49v5925_info },
1307 { "5p49v5933", .driver_data = (kernel_ulong_t)&idt_5p49v5933_info },
1308 { "5p49v5935", .driver_data = (kernel_ulong_t)&idt_5p49v5935_info },
1309 { "5p49v60", .driver_data = (kernel_ulong_t)&idt_5p49v60_info },
1310 { "5p49v6901", .driver_data = (kernel_ulong_t)&idt_5p49v6901_info },
1311 { "5p49v6965", .driver_data = (kernel_ulong_t)&idt_5p49v6965_info },
1312 { "5p49v6975", .driver_data = (kernel_ulong_t)&idt_5p49v6975_info },
1313 { }
1314};
1315MODULE_DEVICE_TABLE(i2c, vc5_id);
1316
1317static const struct of_device_id clk_vc5_of_match[] = {
1318 { .compatible = "idt,5p49v5923", .data = &idt_5p49v5923_info },
1319 { .compatible = "idt,5p49v5925", .data = &idt_5p49v5925_info },
1320 { .compatible = "idt,5p49v5933", .data = &idt_5p49v5933_info },
1321 { .compatible = "idt,5p49v5935", .data = &idt_5p49v5935_info },
1322 { .compatible = "idt,5p49v60", .data = &idt_5p49v60_info },
1323 { .compatible = "idt,5p49v6901", .data = &idt_5p49v6901_info },
1324 { .compatible = "idt,5p49v6965", .data = &idt_5p49v6965_info },
1325 { .compatible = "idt,5p49v6975", .data = &idt_5p49v6975_info },
1326 { },
1327};
1328MODULE_DEVICE_TABLE(of, clk_vc5_of_match);
1329
1330static SIMPLE_DEV_PM_OPS(vc5_pm_ops, vc5_suspend, vc5_resume);
1331
1332static struct i2c_driver vc5_driver = {
1333 .driver = {
1334 .name = "vc5",
1335 .pm = &vc5_pm_ops,
1336 .of_match_table = clk_vc5_of_match,
1337 },
1338 .probe = vc5_probe,
1339 .remove = vc5_remove,
1340 .id_table = vc5_id,
1341};
1342module_i2c_driver(vc5_driver);
1343
1344MODULE_AUTHOR("Marek Vasut <marek.vasut@gmail.com>");
1345MODULE_DESCRIPTION("IDT VersaClock 5 driver");
1346MODULE_LICENSE("GPL");