Loading...
1/*
2 * Freescale eSDHC i.MX controller driver for the platform bus.
3 *
4 * derived from the OF-version.
5 *
6 * Copyright (c) 2010 Pengutronix e.K.
7 * Author: Wolfram Sang <w.sang@pengutronix.de>
8 *
9 * This program is free software; you can redistribute it and/or modify
10 * it under the terms of the GNU General Public License as published by
11 * the Free Software Foundation; either version 2 of the License.
12 */
13
14#include <linux/io.h>
15#include <linux/delay.h>
16#include <linux/err.h>
17#include <linux/clk.h>
18#include <linux/gpio.h>
19#include <linux/module.h>
20#include <linux/slab.h>
21#include <linux/mmc/host.h>
22#include <linux/mmc/mmc.h>
23#include <linux/mmc/sdio.h>
24#include <linux/of.h>
25#include <linux/of_device.h>
26#include <linux/of_gpio.h>
27#include <linux/pinctrl/consumer.h>
28#include <mach/esdhc.h>
29#include "sdhci-pltfm.h"
30#include "sdhci-esdhc.h"
31
32#define SDHCI_CTRL_D3CD 0x08
33/* VENDOR SPEC register */
34#define SDHCI_VENDOR_SPEC 0xC0
35#define SDHCI_VENDOR_SPEC_SDIO_QUIRK 0x00000002
36#define SDHCI_WTMK_LVL 0x44
37#define SDHCI_MIX_CTRL 0x48
38
39/*
40 * There is an INT DMA ERR mis-match between eSDHC and STD SDHC SPEC:
41 * Bit25 is used in STD SPEC, and is reserved in fsl eSDHC design,
42 * but bit28 is used as the INT DMA ERR in fsl eSDHC design.
43 * Define this macro DMA error INT for fsl eSDHC
44 */
45#define SDHCI_INT_VENDOR_SPEC_DMA_ERR 0x10000000
46
47/*
48 * The CMDTYPE of the CMD register (offset 0xE) should be set to
49 * "11" when the STOP CMD12 is issued on imx53 to abort one
50 * open ended multi-blk IO. Otherwise the TC INT wouldn't
51 * be generated.
52 * In exact block transfer, the controller doesn't complete the
53 * operations automatically as required at the end of the
54 * transfer and remains on hold if the abort command is not sent.
55 * As a result, the TC flag is not asserted and SW received timeout
56 * exeception. Bit1 of Vendor Spec registor is used to fix it.
57 */
58#define ESDHC_FLAG_MULTIBLK_NO_INT (1 << 1)
59
60enum imx_esdhc_type {
61 IMX25_ESDHC,
62 IMX35_ESDHC,
63 IMX51_ESDHC,
64 IMX53_ESDHC,
65 IMX6Q_USDHC,
66};
67
68struct pltfm_imx_data {
69 int flags;
70 u32 scratchpad;
71 enum imx_esdhc_type devtype;
72 struct pinctrl *pinctrl;
73 struct esdhc_platform_data boarddata;
74 struct clk *clk_ipg;
75 struct clk *clk_ahb;
76 struct clk *clk_per;
77};
78
79static struct platform_device_id imx_esdhc_devtype[] = {
80 {
81 .name = "sdhci-esdhc-imx25",
82 .driver_data = IMX25_ESDHC,
83 }, {
84 .name = "sdhci-esdhc-imx35",
85 .driver_data = IMX35_ESDHC,
86 }, {
87 .name = "sdhci-esdhc-imx51",
88 .driver_data = IMX51_ESDHC,
89 }, {
90 .name = "sdhci-esdhc-imx53",
91 .driver_data = IMX53_ESDHC,
92 }, {
93 .name = "sdhci-usdhc-imx6q",
94 .driver_data = IMX6Q_USDHC,
95 }, {
96 /* sentinel */
97 }
98};
99MODULE_DEVICE_TABLE(platform, imx_esdhc_devtype);
100
101static const struct of_device_id imx_esdhc_dt_ids[] = {
102 { .compatible = "fsl,imx25-esdhc", .data = &imx_esdhc_devtype[IMX25_ESDHC], },
103 { .compatible = "fsl,imx35-esdhc", .data = &imx_esdhc_devtype[IMX35_ESDHC], },
104 { .compatible = "fsl,imx51-esdhc", .data = &imx_esdhc_devtype[IMX51_ESDHC], },
105 { .compatible = "fsl,imx53-esdhc", .data = &imx_esdhc_devtype[IMX53_ESDHC], },
106 { .compatible = "fsl,imx6q-usdhc", .data = &imx_esdhc_devtype[IMX6Q_USDHC], },
107 { /* sentinel */ }
108};
109MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids);
110
111static inline int is_imx25_esdhc(struct pltfm_imx_data *data)
112{
113 return data->devtype == IMX25_ESDHC;
114}
115
116static inline int is_imx35_esdhc(struct pltfm_imx_data *data)
117{
118 return data->devtype == IMX35_ESDHC;
119}
120
121static inline int is_imx51_esdhc(struct pltfm_imx_data *data)
122{
123 return data->devtype == IMX51_ESDHC;
124}
125
126static inline int is_imx53_esdhc(struct pltfm_imx_data *data)
127{
128 return data->devtype == IMX53_ESDHC;
129}
130
131static inline int is_imx6q_usdhc(struct pltfm_imx_data *data)
132{
133 return data->devtype == IMX6Q_USDHC;
134}
135
136static inline void esdhc_clrset_le(struct sdhci_host *host, u32 mask, u32 val, int reg)
137{
138 void __iomem *base = host->ioaddr + (reg & ~0x3);
139 u32 shift = (reg & 0x3) * 8;
140
141 writel(((readl(base) & ~(mask << shift)) | (val << shift)), base);
142}
143
144static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
145{
146 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
147 struct pltfm_imx_data *imx_data = pltfm_host->priv;
148 struct esdhc_platform_data *boarddata = &imx_data->boarddata;
149
150 /* fake CARD_PRESENT flag */
151 u32 val = readl(host->ioaddr + reg);
152
153 if (unlikely((reg == SDHCI_PRESENT_STATE)
154 && gpio_is_valid(boarddata->cd_gpio))) {
155 if (gpio_get_value(boarddata->cd_gpio))
156 /* no card, if a valid gpio says so... */
157 val &= ~SDHCI_CARD_PRESENT;
158 else
159 /* ... in all other cases assume card is present */
160 val |= SDHCI_CARD_PRESENT;
161 }
162
163 if (unlikely(reg == SDHCI_CAPABILITIES)) {
164 /* In FSL esdhc IC module, only bit20 is used to indicate the
165 * ADMA2 capability of esdhc, but this bit is messed up on
166 * some SOCs (e.g. on MX25, MX35 this bit is set, but they
167 * don't actually support ADMA2). So set the BROKEN_ADMA
168 * uirk on MX25/35 platforms.
169 */
170
171 if (val & SDHCI_CAN_DO_ADMA1) {
172 val &= ~SDHCI_CAN_DO_ADMA1;
173 val |= SDHCI_CAN_DO_ADMA2;
174 }
175 }
176
177 if (unlikely(reg == SDHCI_INT_STATUS)) {
178 if (val & SDHCI_INT_VENDOR_SPEC_DMA_ERR) {
179 val &= ~SDHCI_INT_VENDOR_SPEC_DMA_ERR;
180 val |= SDHCI_INT_ADMA_ERROR;
181 }
182 }
183
184 return val;
185}
186
187static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg)
188{
189 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
190 struct pltfm_imx_data *imx_data = pltfm_host->priv;
191 struct esdhc_platform_data *boarddata = &imx_data->boarddata;
192 u32 data;
193
194 if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE)) {
195 if (boarddata->cd_type == ESDHC_CD_GPIO)
196 /*
197 * These interrupts won't work with a custom
198 * card_detect gpio (only applied to mx25/35)
199 */
200 val &= ~(SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT);
201
202 if (val & SDHCI_INT_CARD_INT) {
203 /*
204 * Clear and then set D3CD bit to avoid missing the
205 * card interrupt. This is a eSDHC controller problem
206 * so we need to apply the following workaround: clear
207 * and set D3CD bit will make eSDHC re-sample the card
208 * interrupt. In case a card interrupt was lost,
209 * re-sample it by the following steps.
210 */
211 data = readl(host->ioaddr + SDHCI_HOST_CONTROL);
212 data &= ~SDHCI_CTRL_D3CD;
213 writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
214 data |= SDHCI_CTRL_D3CD;
215 writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
216 }
217 }
218
219 if (unlikely((imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
220 && (reg == SDHCI_INT_STATUS)
221 && (val & SDHCI_INT_DATA_END))) {
222 u32 v;
223 v = readl(host->ioaddr + SDHCI_VENDOR_SPEC);
224 v &= ~SDHCI_VENDOR_SPEC_SDIO_QUIRK;
225 writel(v, host->ioaddr + SDHCI_VENDOR_SPEC);
226 }
227
228 if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE)) {
229 if (val & SDHCI_INT_ADMA_ERROR) {
230 val &= ~SDHCI_INT_ADMA_ERROR;
231 val |= SDHCI_INT_VENDOR_SPEC_DMA_ERR;
232 }
233 }
234
235 writel(val, host->ioaddr + reg);
236}
237
238static u16 esdhc_readw_le(struct sdhci_host *host, int reg)
239{
240 if (unlikely(reg == SDHCI_HOST_VERSION)) {
241 u16 val = readw(host->ioaddr + (reg ^ 2));
242 /*
243 * uSDHC supports SDHCI v3.0, but it's encoded as value
244 * 0x3 in host controller version register, which violates
245 * SDHCI_SPEC_300 definition. Work it around here.
246 */
247 if ((val & SDHCI_SPEC_VER_MASK) == 3)
248 return --val;
249 }
250
251 return readw(host->ioaddr + reg);
252}
253
254static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
255{
256 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
257 struct pltfm_imx_data *imx_data = pltfm_host->priv;
258
259 switch (reg) {
260 case SDHCI_TRANSFER_MODE:
261 /*
262 * Postpone this write, we must do it together with a
263 * command write that is down below.
264 */
265 if ((imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
266 && (host->cmd->opcode == SD_IO_RW_EXTENDED)
267 && (host->cmd->data->blocks > 1)
268 && (host->cmd->data->flags & MMC_DATA_READ)) {
269 u32 v;
270 v = readl(host->ioaddr + SDHCI_VENDOR_SPEC);
271 v |= SDHCI_VENDOR_SPEC_SDIO_QUIRK;
272 writel(v, host->ioaddr + SDHCI_VENDOR_SPEC);
273 }
274 imx_data->scratchpad = val;
275 return;
276 case SDHCI_COMMAND:
277 if ((host->cmd->opcode == MMC_STOP_TRANSMISSION ||
278 host->cmd->opcode == MMC_SET_BLOCK_COUNT) &&
279 (imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
280 val |= SDHCI_CMD_ABORTCMD;
281
282 if (is_imx6q_usdhc(imx_data)) {
283 u32 m = readl(host->ioaddr + SDHCI_MIX_CTRL);
284 m = imx_data->scratchpad | (m & 0xffff0000);
285 writel(m, host->ioaddr + SDHCI_MIX_CTRL);
286 writel(val << 16,
287 host->ioaddr + SDHCI_TRANSFER_MODE);
288 } else {
289 writel(val << 16 | imx_data->scratchpad,
290 host->ioaddr + SDHCI_TRANSFER_MODE);
291 }
292 return;
293 case SDHCI_BLOCK_SIZE:
294 val &= ~SDHCI_MAKE_BLKSZ(0x7, 0);
295 break;
296 }
297 esdhc_clrset_le(host, 0xffff, val, reg);
298}
299
300static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg)
301{
302 u32 new_val;
303
304 switch (reg) {
305 case SDHCI_POWER_CONTROL:
306 /*
307 * FSL put some DMA bits here
308 * If your board has a regulator, code should be here
309 */
310 return;
311 case SDHCI_HOST_CONTROL:
312 /* FSL messed up here, so we can just keep those three */
313 new_val = val & (SDHCI_CTRL_LED | \
314 SDHCI_CTRL_4BITBUS | \
315 SDHCI_CTRL_D3CD);
316 /* ensure the endianess */
317 new_val |= ESDHC_HOST_CONTROL_LE;
318 /* DMA mode bits are shifted */
319 new_val |= (val & SDHCI_CTRL_DMA_MASK) << 5;
320
321 esdhc_clrset_le(host, 0xffff, new_val, reg);
322 return;
323 }
324 esdhc_clrset_le(host, 0xff, val, reg);
325
326 /*
327 * The esdhc has a design violation to SDHC spec which tells
328 * that software reset should not affect card detection circuit.
329 * But esdhc clears its SYSCTL register bits [0..2] during the
330 * software reset. This will stop those clocks that card detection
331 * circuit relies on. To work around it, we turn the clocks on back
332 * to keep card detection circuit functional.
333 */
334 if ((reg == SDHCI_SOFTWARE_RESET) && (val & 1))
335 esdhc_clrset_le(host, 0x7, 0x7, ESDHC_SYSTEM_CONTROL);
336}
337
338static unsigned int esdhc_pltfm_get_max_clock(struct sdhci_host *host)
339{
340 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
341
342 return clk_get_rate(pltfm_host->clk);
343}
344
345static unsigned int esdhc_pltfm_get_min_clock(struct sdhci_host *host)
346{
347 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
348
349 return clk_get_rate(pltfm_host->clk) / 256 / 16;
350}
351
352static unsigned int esdhc_pltfm_get_ro(struct sdhci_host *host)
353{
354 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
355 struct pltfm_imx_data *imx_data = pltfm_host->priv;
356 struct esdhc_platform_data *boarddata = &imx_data->boarddata;
357
358 switch (boarddata->wp_type) {
359 case ESDHC_WP_GPIO:
360 if (gpio_is_valid(boarddata->wp_gpio))
361 return gpio_get_value(boarddata->wp_gpio);
362 case ESDHC_WP_CONTROLLER:
363 return !(readl(host->ioaddr + SDHCI_PRESENT_STATE) &
364 SDHCI_WRITE_PROTECT);
365 case ESDHC_WP_NONE:
366 break;
367 }
368
369 return -ENOSYS;
370}
371
372static struct sdhci_ops sdhci_esdhc_ops = {
373 .read_l = esdhc_readl_le,
374 .read_w = esdhc_readw_le,
375 .write_l = esdhc_writel_le,
376 .write_w = esdhc_writew_le,
377 .write_b = esdhc_writeb_le,
378 .set_clock = esdhc_set_clock,
379 .get_max_clock = esdhc_pltfm_get_max_clock,
380 .get_min_clock = esdhc_pltfm_get_min_clock,
381 .get_ro = esdhc_pltfm_get_ro,
382};
383
384static struct sdhci_pltfm_data sdhci_esdhc_imx_pdata = {
385 .quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_NO_HISPD_BIT
386 | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
387 | SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC
388 | SDHCI_QUIRK_BROKEN_CARD_DETECTION,
389 .ops = &sdhci_esdhc_ops,
390};
391
392static irqreturn_t cd_irq(int irq, void *data)
393{
394 struct sdhci_host *sdhost = (struct sdhci_host *)data;
395
396 tasklet_schedule(&sdhost->card_tasklet);
397 return IRQ_HANDLED;
398};
399
400#ifdef CONFIG_OF
401static int __devinit
402sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
403 struct esdhc_platform_data *boarddata)
404{
405 struct device_node *np = pdev->dev.of_node;
406
407 if (!np)
408 return -ENODEV;
409
410 if (of_get_property(np, "non-removable", NULL))
411 boarddata->cd_type = ESDHC_CD_PERMANENT;
412
413 if (of_get_property(np, "fsl,cd-controller", NULL))
414 boarddata->cd_type = ESDHC_CD_CONTROLLER;
415
416 if (of_get_property(np, "fsl,wp-controller", NULL))
417 boarddata->wp_type = ESDHC_WP_CONTROLLER;
418
419 boarddata->cd_gpio = of_get_named_gpio(np, "cd-gpios", 0);
420 if (gpio_is_valid(boarddata->cd_gpio))
421 boarddata->cd_type = ESDHC_CD_GPIO;
422
423 boarddata->wp_gpio = of_get_named_gpio(np, "wp-gpios", 0);
424 if (gpio_is_valid(boarddata->wp_gpio))
425 boarddata->wp_type = ESDHC_WP_GPIO;
426
427 return 0;
428}
429#else
430static inline int
431sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
432 struct esdhc_platform_data *boarddata)
433{
434 return -ENODEV;
435}
436#endif
437
438static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev)
439{
440 const struct of_device_id *of_id =
441 of_match_device(imx_esdhc_dt_ids, &pdev->dev);
442 struct sdhci_pltfm_host *pltfm_host;
443 struct sdhci_host *host;
444 struct esdhc_platform_data *boarddata;
445 int err;
446 struct pltfm_imx_data *imx_data;
447
448 host = sdhci_pltfm_init(pdev, &sdhci_esdhc_imx_pdata);
449 if (IS_ERR(host))
450 return PTR_ERR(host);
451
452 pltfm_host = sdhci_priv(host);
453
454 imx_data = kzalloc(sizeof(struct pltfm_imx_data), GFP_KERNEL);
455 if (!imx_data) {
456 err = -ENOMEM;
457 goto err_imx_data;
458 }
459
460 if (of_id)
461 pdev->id_entry = of_id->data;
462 imx_data->devtype = pdev->id_entry->driver_data;
463 pltfm_host->priv = imx_data;
464
465 imx_data->clk_ipg = devm_clk_get(&pdev->dev, "ipg");
466 if (IS_ERR(imx_data->clk_ipg)) {
467 err = PTR_ERR(imx_data->clk_ipg);
468 goto err_clk_get;
469 }
470
471 imx_data->clk_ahb = devm_clk_get(&pdev->dev, "ahb");
472 if (IS_ERR(imx_data->clk_ahb)) {
473 err = PTR_ERR(imx_data->clk_ahb);
474 goto err_clk_get;
475 }
476
477 imx_data->clk_per = devm_clk_get(&pdev->dev, "per");
478 if (IS_ERR(imx_data->clk_per)) {
479 err = PTR_ERR(imx_data->clk_per);
480 goto err_clk_get;
481 }
482
483 pltfm_host->clk = imx_data->clk_per;
484
485 clk_prepare_enable(imx_data->clk_per);
486 clk_prepare_enable(imx_data->clk_ipg);
487 clk_prepare_enable(imx_data->clk_ahb);
488
489 imx_data->pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
490 if (IS_ERR(imx_data->pinctrl)) {
491 err = PTR_ERR(imx_data->pinctrl);
492 goto pin_err;
493 }
494
495 host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
496
497 if (is_imx25_esdhc(imx_data) || is_imx35_esdhc(imx_data))
498 /* Fix errata ENGcm07207 present on i.MX25 and i.MX35 */
499 host->quirks |= SDHCI_QUIRK_NO_MULTIBLOCK
500 | SDHCI_QUIRK_BROKEN_ADMA;
501
502 if (is_imx53_esdhc(imx_data))
503 imx_data->flags |= ESDHC_FLAG_MULTIBLK_NO_INT;
504
505 /*
506 * The imx6q ROM code will change the default watermark level setting
507 * to something insane. Change it back here.
508 */
509 if (is_imx6q_usdhc(imx_data))
510 writel(0x08100810, host->ioaddr + SDHCI_WTMK_LVL);
511
512 boarddata = &imx_data->boarddata;
513 if (sdhci_esdhc_imx_probe_dt(pdev, boarddata) < 0) {
514 if (!host->mmc->parent->platform_data) {
515 dev_err(mmc_dev(host->mmc), "no board data!\n");
516 err = -EINVAL;
517 goto no_board_data;
518 }
519 imx_data->boarddata = *((struct esdhc_platform_data *)
520 host->mmc->parent->platform_data);
521 }
522
523 /* write_protect */
524 if (boarddata->wp_type == ESDHC_WP_GPIO) {
525 err = gpio_request_one(boarddata->wp_gpio, GPIOF_IN, "ESDHC_WP");
526 if (err) {
527 dev_warn(mmc_dev(host->mmc),
528 "no write-protect pin available!\n");
529 boarddata->wp_gpio = -EINVAL;
530 }
531 } else {
532 boarddata->wp_gpio = -EINVAL;
533 }
534
535 /* card_detect */
536 if (boarddata->cd_type != ESDHC_CD_GPIO)
537 boarddata->cd_gpio = -EINVAL;
538
539 switch (boarddata->cd_type) {
540 case ESDHC_CD_GPIO:
541 err = gpio_request_one(boarddata->cd_gpio, GPIOF_IN, "ESDHC_CD");
542 if (err) {
543 dev_err(mmc_dev(host->mmc),
544 "no card-detect pin available!\n");
545 goto no_card_detect_pin;
546 }
547
548 err = request_irq(gpio_to_irq(boarddata->cd_gpio), cd_irq,
549 IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
550 mmc_hostname(host->mmc), host);
551 if (err) {
552 dev_err(mmc_dev(host->mmc), "request irq error\n");
553 goto no_card_detect_irq;
554 }
555 /* fall through */
556
557 case ESDHC_CD_CONTROLLER:
558 /* we have a working card_detect back */
559 host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION;
560 break;
561
562 case ESDHC_CD_PERMANENT:
563 host->mmc->caps = MMC_CAP_NONREMOVABLE;
564 break;
565
566 case ESDHC_CD_NONE:
567 break;
568 }
569
570 err = sdhci_add_host(host);
571 if (err)
572 goto err_add_host;
573
574 return 0;
575
576err_add_host:
577 if (gpio_is_valid(boarddata->cd_gpio))
578 free_irq(gpio_to_irq(boarddata->cd_gpio), host);
579no_card_detect_irq:
580 if (gpio_is_valid(boarddata->cd_gpio))
581 gpio_free(boarddata->cd_gpio);
582 if (gpio_is_valid(boarddata->wp_gpio))
583 gpio_free(boarddata->wp_gpio);
584no_card_detect_pin:
585no_board_data:
586pin_err:
587 clk_disable_unprepare(imx_data->clk_per);
588 clk_disable_unprepare(imx_data->clk_ipg);
589 clk_disable_unprepare(imx_data->clk_ahb);
590err_clk_get:
591 kfree(imx_data);
592err_imx_data:
593 sdhci_pltfm_free(pdev);
594 return err;
595}
596
597static int __devexit sdhci_esdhc_imx_remove(struct platform_device *pdev)
598{
599 struct sdhci_host *host = platform_get_drvdata(pdev);
600 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
601 struct pltfm_imx_data *imx_data = pltfm_host->priv;
602 struct esdhc_platform_data *boarddata = &imx_data->boarddata;
603 int dead = (readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff);
604
605 sdhci_remove_host(host, dead);
606
607 if (gpio_is_valid(boarddata->wp_gpio))
608 gpio_free(boarddata->wp_gpio);
609
610 if (gpio_is_valid(boarddata->cd_gpio)) {
611 free_irq(gpio_to_irq(boarddata->cd_gpio), host);
612 gpio_free(boarddata->cd_gpio);
613 }
614
615 clk_disable_unprepare(imx_data->clk_per);
616 clk_disable_unprepare(imx_data->clk_ipg);
617 clk_disable_unprepare(imx_data->clk_ahb);
618
619 kfree(imx_data);
620
621 sdhci_pltfm_free(pdev);
622
623 return 0;
624}
625
626static struct platform_driver sdhci_esdhc_imx_driver = {
627 .driver = {
628 .name = "sdhci-esdhc-imx",
629 .owner = THIS_MODULE,
630 .of_match_table = imx_esdhc_dt_ids,
631 .pm = SDHCI_PLTFM_PMOPS,
632 },
633 .id_table = imx_esdhc_devtype,
634 .probe = sdhci_esdhc_imx_probe,
635 .remove = __devexit_p(sdhci_esdhc_imx_remove),
636};
637
638module_platform_driver(sdhci_esdhc_imx_driver);
639
640MODULE_DESCRIPTION("SDHCI driver for Freescale i.MX eSDHC");
641MODULE_AUTHOR("Wolfram Sang <w.sang@pengutronix.de>");
642MODULE_LICENSE("GPL v2");
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Freescale eSDHC i.MX controller driver for the platform bus.
4 *
5 * derived from the OF-version.
6 *
7 * Copyright (c) 2010 Pengutronix e.K.
8 * Author: Wolfram Sang <kernel@pengutronix.de>
9 */
10
11#include <linux/bitfield.h>
12#include <linux/io.h>
13#include <linux/iopoll.h>
14#include <linux/delay.h>
15#include <linux/err.h>
16#include <linux/clk.h>
17#include <linux/module.h>
18#include <linux/slab.h>
19#include <linux/pm_qos.h>
20#include <linux/mmc/host.h>
21#include <linux/mmc/mmc.h>
22#include <linux/mmc/sdio.h>
23#include <linux/mmc/slot-gpio.h>
24#include <linux/of.h>
25#include <linux/of_device.h>
26#include <linux/pinctrl/consumer.h>
27#include <linux/platform_data/mmc-esdhc-imx.h>
28#include <linux/pm_runtime.h>
29#include "sdhci-pltfm.h"
30#include "sdhci-esdhc.h"
31#include "cqhci.h"
32
33#define ESDHC_SYS_CTRL_DTOCV_MASK 0x0f
34#define ESDHC_CTRL_D3CD 0x08
35#define ESDHC_BURST_LEN_EN_INCR (1 << 27)
36/* VENDOR SPEC register */
37#define ESDHC_VENDOR_SPEC 0xc0
38#define ESDHC_VENDOR_SPEC_SDIO_QUIRK (1 << 1)
39#define ESDHC_VENDOR_SPEC_VSELECT (1 << 1)
40#define ESDHC_VENDOR_SPEC_FRC_SDCLK_ON (1 << 8)
41#define ESDHC_DEBUG_SEL_AND_STATUS_REG 0xc2
42#define ESDHC_DEBUG_SEL_REG 0xc3
43#define ESDHC_DEBUG_SEL_MASK 0xf
44#define ESDHC_DEBUG_SEL_CMD_STATE 1
45#define ESDHC_DEBUG_SEL_DATA_STATE 2
46#define ESDHC_DEBUG_SEL_TRANS_STATE 3
47#define ESDHC_DEBUG_SEL_DMA_STATE 4
48#define ESDHC_DEBUG_SEL_ADMA_STATE 5
49#define ESDHC_DEBUG_SEL_FIFO_STATE 6
50#define ESDHC_DEBUG_SEL_ASYNC_FIFO_STATE 7
51#define ESDHC_WTMK_LVL 0x44
52#define ESDHC_WTMK_DEFAULT_VAL 0x10401040
53#define ESDHC_WTMK_LVL_RD_WML_MASK 0x000000FF
54#define ESDHC_WTMK_LVL_RD_WML_SHIFT 0
55#define ESDHC_WTMK_LVL_WR_WML_MASK 0x00FF0000
56#define ESDHC_WTMK_LVL_WR_WML_SHIFT 16
57#define ESDHC_WTMK_LVL_WML_VAL_DEF 64
58#define ESDHC_WTMK_LVL_WML_VAL_MAX 128
59#define ESDHC_MIX_CTRL 0x48
60#define ESDHC_MIX_CTRL_DDREN (1 << 3)
61#define ESDHC_MIX_CTRL_AC23EN (1 << 7)
62#define ESDHC_MIX_CTRL_EXE_TUNE (1 << 22)
63#define ESDHC_MIX_CTRL_SMPCLK_SEL (1 << 23)
64#define ESDHC_MIX_CTRL_AUTO_TUNE_EN (1 << 24)
65#define ESDHC_MIX_CTRL_FBCLK_SEL (1 << 25)
66#define ESDHC_MIX_CTRL_HS400_EN (1 << 26)
67#define ESDHC_MIX_CTRL_HS400_ES_EN (1 << 27)
68/* Bits 3 and 6 are not SDHCI standard definitions */
69#define ESDHC_MIX_CTRL_SDHCI_MASK 0xb7
70/* Tuning bits */
71#define ESDHC_MIX_CTRL_TUNING_MASK 0x03c00000
72
73/* dll control register */
74#define ESDHC_DLL_CTRL 0x60
75#define ESDHC_DLL_OVERRIDE_VAL_SHIFT 9
76#define ESDHC_DLL_OVERRIDE_EN_SHIFT 8
77
78/* tune control register */
79#define ESDHC_TUNE_CTRL_STATUS 0x68
80#define ESDHC_TUNE_CTRL_STEP 1
81#define ESDHC_TUNE_CTRL_MIN 0
82#define ESDHC_TUNE_CTRL_MAX ((1 << 7) - 1)
83
84/* strobe dll register */
85#define ESDHC_STROBE_DLL_CTRL 0x70
86#define ESDHC_STROBE_DLL_CTRL_ENABLE (1 << 0)
87#define ESDHC_STROBE_DLL_CTRL_RESET (1 << 1)
88#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT 0x7
89#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT 3
90#define ESDHC_STROBE_DLL_CTRL_SLV_UPDATE_INT_DEFAULT (4 << 20)
91
92#define ESDHC_STROBE_DLL_STATUS 0x74
93#define ESDHC_STROBE_DLL_STS_REF_LOCK (1 << 1)
94#define ESDHC_STROBE_DLL_STS_SLV_LOCK 0x1
95
96#define ESDHC_VEND_SPEC2 0xc8
97#define ESDHC_VEND_SPEC2_EN_BUSY_IRQ (1 << 8)
98
99#define ESDHC_TUNING_CTRL 0xcc
100#define ESDHC_STD_TUNING_EN (1 << 24)
101/* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
102#define ESDHC_TUNING_START_TAP_DEFAULT 0x1
103#define ESDHC_TUNING_START_TAP_MASK 0x7f
104#define ESDHC_TUNING_CMD_CRC_CHECK_DISABLE (1 << 7)
105#define ESDHC_TUNING_STEP_MASK 0x00070000
106#define ESDHC_TUNING_STEP_SHIFT 16
107
108/* pinctrl state */
109#define ESDHC_PINCTRL_STATE_100MHZ "state_100mhz"
110#define ESDHC_PINCTRL_STATE_200MHZ "state_200mhz"
111
112/*
113 * Our interpretation of the SDHCI_HOST_CONTROL register
114 */
115#define ESDHC_CTRL_4BITBUS (0x1 << 1)
116#define ESDHC_CTRL_8BITBUS (0x2 << 1)
117#define ESDHC_CTRL_BUSWIDTH_MASK (0x3 << 1)
118
119/*
120 * There is an INT DMA ERR mismatch between eSDHC and STD SDHC SPEC:
121 * Bit25 is used in STD SPEC, and is reserved in fsl eSDHC design,
122 * but bit28 is used as the INT DMA ERR in fsl eSDHC design.
123 * Define this macro DMA error INT for fsl eSDHC
124 */
125#define ESDHC_INT_VENDOR_SPEC_DMA_ERR (1 << 28)
126
127/* the address offset of CQHCI */
128#define ESDHC_CQHCI_ADDR_OFFSET 0x100
129
130/*
131 * The CMDTYPE of the CMD register (offset 0xE) should be set to
132 * "11" when the STOP CMD12 is issued on imx53 to abort one
133 * open ended multi-blk IO. Otherwise the TC INT wouldn't
134 * be generated.
135 * In exact block transfer, the controller doesn't complete the
136 * operations automatically as required at the end of the
137 * transfer and remains on hold if the abort command is not sent.
138 * As a result, the TC flag is not asserted and SW received timeout
139 * exception. Bit1 of Vendor Spec register is used to fix it.
140 */
141#define ESDHC_FLAG_MULTIBLK_NO_INT BIT(1)
142/*
143 * The flag tells that the ESDHC controller is an USDHC block that is
144 * integrated on the i.MX6 series.
145 */
146#define ESDHC_FLAG_USDHC BIT(3)
147/* The IP supports manual tuning process */
148#define ESDHC_FLAG_MAN_TUNING BIT(4)
149/* The IP supports standard tuning process */
150#define ESDHC_FLAG_STD_TUNING BIT(5)
151/* The IP has SDHCI_CAPABILITIES_1 register */
152#define ESDHC_FLAG_HAVE_CAP1 BIT(6)
153/*
154 * The IP has erratum ERR004536
155 * uSDHC: ADMA Length Mismatch Error occurs if the AHB read access is slow,
156 * when reading data from the card
157 * This flag is also set for i.MX25 and i.MX35 in order to get
158 * SDHCI_QUIRK_BROKEN_ADMA, but for different reasons (ADMA capability bits).
159 */
160#define ESDHC_FLAG_ERR004536 BIT(7)
161/* The IP supports HS200 mode */
162#define ESDHC_FLAG_HS200 BIT(8)
163/* The IP supports HS400 mode */
164#define ESDHC_FLAG_HS400 BIT(9)
165/*
166 * The IP has errata ERR010450
167 * uSDHC: Due to the I/O timing limit, for SDR mode, SD card clock can't
168 * exceed 150MHz, for DDR mode, SD card clock can't exceed 45MHz.
169 */
170#define ESDHC_FLAG_ERR010450 BIT(10)
171/* The IP supports HS400ES mode */
172#define ESDHC_FLAG_HS400_ES BIT(11)
173/* The IP has Host Controller Interface for Command Queuing */
174#define ESDHC_FLAG_CQHCI BIT(12)
175/* need request pmqos during low power */
176#define ESDHC_FLAG_PMQOS BIT(13)
177/* The IP state got lost in low power mode */
178#define ESDHC_FLAG_STATE_LOST_IN_LPMODE BIT(14)
179/* The IP lost clock rate in PM_RUNTIME */
180#define ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME BIT(15)
181/*
182 * The IP do not support the ACMD23 feature completely when use ADMA mode.
183 * In ADMA mode, it only use the 16 bit block count of the register 0x4
184 * (BLOCK_ATT) as the CMD23's argument for ACMD23 mode, which means it will
185 * ignore the upper 16 bit of the CMD23's argument. This will block the reliable
186 * write operation in RPMB, because RPMB reliable write need to set the bit31
187 * of the CMD23's argument.
188 * imx6qpdl/imx6sx/imx6sl/imx7d has this limitation only for ADMA mode, SDMA
189 * do not has this limitation. so when these SoC use ADMA mode, it need to
190 * disable the ACMD23 feature.
191 */
192#define ESDHC_FLAG_BROKEN_AUTO_CMD23 BIT(16)
193
194struct esdhc_soc_data {
195 u32 flags;
196};
197
198static const struct esdhc_soc_data esdhc_imx25_data = {
199 .flags = ESDHC_FLAG_ERR004536,
200};
201
202static const struct esdhc_soc_data esdhc_imx35_data = {
203 .flags = ESDHC_FLAG_ERR004536,
204};
205
206static const struct esdhc_soc_data esdhc_imx51_data = {
207 .flags = 0,
208};
209
210static const struct esdhc_soc_data esdhc_imx53_data = {
211 .flags = ESDHC_FLAG_MULTIBLK_NO_INT,
212};
213
214static const struct esdhc_soc_data usdhc_imx6q_data = {
215 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_MAN_TUNING
216 | ESDHC_FLAG_BROKEN_AUTO_CMD23,
217};
218
219static const struct esdhc_soc_data usdhc_imx6sl_data = {
220 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
221 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_ERR004536
222 | ESDHC_FLAG_HS200
223 | ESDHC_FLAG_BROKEN_AUTO_CMD23,
224};
225
226static const struct esdhc_soc_data usdhc_imx6sll_data = {
227 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
228 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
229 | ESDHC_FLAG_HS400
230 | ESDHC_FLAG_STATE_LOST_IN_LPMODE,
231};
232
233static const struct esdhc_soc_data usdhc_imx6sx_data = {
234 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
235 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
236 | ESDHC_FLAG_STATE_LOST_IN_LPMODE
237 | ESDHC_FLAG_BROKEN_AUTO_CMD23,
238};
239
240static const struct esdhc_soc_data usdhc_imx6ull_data = {
241 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
242 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
243 | ESDHC_FLAG_ERR010450
244 | ESDHC_FLAG_STATE_LOST_IN_LPMODE,
245};
246
247static const struct esdhc_soc_data usdhc_imx7d_data = {
248 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
249 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
250 | ESDHC_FLAG_HS400
251 | ESDHC_FLAG_STATE_LOST_IN_LPMODE
252 | ESDHC_FLAG_BROKEN_AUTO_CMD23,
253};
254
255static struct esdhc_soc_data usdhc_imx7ulp_data = {
256 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
257 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
258 | ESDHC_FLAG_PMQOS | ESDHC_FLAG_HS400
259 | ESDHC_FLAG_STATE_LOST_IN_LPMODE,
260};
261
262static struct esdhc_soc_data usdhc_imx8qxp_data = {
263 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
264 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
265 | ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES
266 | ESDHC_FLAG_CQHCI
267 | ESDHC_FLAG_STATE_LOST_IN_LPMODE
268 | ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME,
269};
270
271static struct esdhc_soc_data usdhc_imx8mm_data = {
272 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
273 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
274 | ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES
275 | ESDHC_FLAG_CQHCI
276 | ESDHC_FLAG_STATE_LOST_IN_LPMODE,
277};
278
279struct pltfm_imx_data {
280 u32 scratchpad;
281 struct pinctrl *pinctrl;
282 struct pinctrl_state *pins_100mhz;
283 struct pinctrl_state *pins_200mhz;
284 const struct esdhc_soc_data *socdata;
285 struct esdhc_platform_data boarddata;
286 struct clk *clk_ipg;
287 struct clk *clk_ahb;
288 struct clk *clk_per;
289 unsigned int actual_clock;
290 enum {
291 NO_CMD_PENDING, /* no multiblock command pending */
292 MULTIBLK_IN_PROCESS, /* exact multiblock cmd in process */
293 WAIT_FOR_INT, /* sent CMD12, waiting for response INT */
294 } multiblock_status;
295 u32 is_ddr;
296 struct pm_qos_request pm_qos_req;
297};
298
299static const struct platform_device_id imx_esdhc_devtype[] = {
300 {
301 .name = "sdhci-esdhc-imx25",
302 .driver_data = (kernel_ulong_t) &esdhc_imx25_data,
303 }, {
304 .name = "sdhci-esdhc-imx35",
305 .driver_data = (kernel_ulong_t) &esdhc_imx35_data,
306 }, {
307 .name = "sdhci-esdhc-imx51",
308 .driver_data = (kernel_ulong_t) &esdhc_imx51_data,
309 }, {
310 /* sentinel */
311 }
312};
313MODULE_DEVICE_TABLE(platform, imx_esdhc_devtype);
314
315static const struct of_device_id imx_esdhc_dt_ids[] = {
316 { .compatible = "fsl,imx25-esdhc", .data = &esdhc_imx25_data, },
317 { .compatible = "fsl,imx35-esdhc", .data = &esdhc_imx35_data, },
318 { .compatible = "fsl,imx51-esdhc", .data = &esdhc_imx51_data, },
319 { .compatible = "fsl,imx53-esdhc", .data = &esdhc_imx53_data, },
320 { .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },
321 { .compatible = "fsl,imx6sl-usdhc", .data = &usdhc_imx6sl_data, },
322 { .compatible = "fsl,imx6sll-usdhc", .data = &usdhc_imx6sll_data, },
323 { .compatible = "fsl,imx6q-usdhc", .data = &usdhc_imx6q_data, },
324 { .compatible = "fsl,imx6ull-usdhc", .data = &usdhc_imx6ull_data, },
325 { .compatible = "fsl,imx7d-usdhc", .data = &usdhc_imx7d_data, },
326 { .compatible = "fsl,imx7ulp-usdhc", .data = &usdhc_imx7ulp_data, },
327 { .compatible = "fsl,imx8qxp-usdhc", .data = &usdhc_imx8qxp_data, },
328 { .compatible = "fsl,imx8mm-usdhc", .data = &usdhc_imx8mm_data, },
329 { /* sentinel */ }
330};
331MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids);
332
333static inline int is_imx25_esdhc(struct pltfm_imx_data *data)
334{
335 return data->socdata == &esdhc_imx25_data;
336}
337
338static inline int is_imx53_esdhc(struct pltfm_imx_data *data)
339{
340 return data->socdata == &esdhc_imx53_data;
341}
342
343static inline int is_imx6q_usdhc(struct pltfm_imx_data *data)
344{
345 return data->socdata == &usdhc_imx6q_data;
346}
347
348static inline int esdhc_is_usdhc(struct pltfm_imx_data *data)
349{
350 return !!(data->socdata->flags & ESDHC_FLAG_USDHC);
351}
352
353static inline void esdhc_clrset_le(struct sdhci_host *host, u32 mask, u32 val, int reg)
354{
355 void __iomem *base = host->ioaddr + (reg & ~0x3);
356 u32 shift = (reg & 0x3) * 8;
357
358 writel(((readl(base) & ~(mask << shift)) | (val << shift)), base);
359}
360
361#define DRIVER_NAME "sdhci-esdhc-imx"
362#define ESDHC_IMX_DUMP(f, x...) \
363 pr_err("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x)
364static void esdhc_dump_debug_regs(struct sdhci_host *host)
365{
366 int i;
367 char *debug_status[7] = {
368 "cmd debug status",
369 "data debug status",
370 "trans debug status",
371 "dma debug status",
372 "adma debug status",
373 "fifo debug status",
374 "async fifo debug status"
375 };
376
377 ESDHC_IMX_DUMP("========= ESDHC IMX DEBUG STATUS DUMP =========\n");
378 for (i = 0; i < 7; i++) {
379 esdhc_clrset_le(host, ESDHC_DEBUG_SEL_MASK,
380 ESDHC_DEBUG_SEL_CMD_STATE + i, ESDHC_DEBUG_SEL_REG);
381 ESDHC_IMX_DUMP("%s: 0x%04x\n", debug_status[i],
382 readw(host->ioaddr + ESDHC_DEBUG_SEL_AND_STATUS_REG));
383 }
384
385 esdhc_clrset_le(host, ESDHC_DEBUG_SEL_MASK, 0, ESDHC_DEBUG_SEL_REG);
386
387}
388
389static inline void esdhc_wait_for_card_clock_gate_off(struct sdhci_host *host)
390{
391 u32 present_state;
392 int ret;
393
394 ret = readl_poll_timeout(host->ioaddr + ESDHC_PRSSTAT, present_state,
395 (present_state & ESDHC_CLOCK_GATE_OFF), 2, 100);
396 if (ret == -ETIMEDOUT)
397 dev_warn(mmc_dev(host->mmc), "%s: card clock still not gate off in 100us!.\n", __func__);
398}
399
400static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
401{
402 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
403 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
404 u32 val = readl(host->ioaddr + reg);
405
406 if (unlikely(reg == SDHCI_PRESENT_STATE)) {
407 u32 fsl_prss = val;
408 /* save the least 20 bits */
409 val = fsl_prss & 0x000FFFFF;
410 /* move dat[0-3] bits */
411 val |= (fsl_prss & 0x0F000000) >> 4;
412 /* move cmd line bit */
413 val |= (fsl_prss & 0x00800000) << 1;
414 }
415
416 if (unlikely(reg == SDHCI_CAPABILITIES)) {
417 /* ignore bit[0-15] as it stores cap_1 register val for mx6sl */
418 if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1)
419 val &= 0xffff0000;
420
421 /* In FSL esdhc IC module, only bit20 is used to indicate the
422 * ADMA2 capability of esdhc, but this bit is messed up on
423 * some SOCs (e.g. on MX25, MX35 this bit is set, but they
424 * don't actually support ADMA2). So set the BROKEN_ADMA
425 * quirk on MX25/35 platforms.
426 */
427
428 if (val & SDHCI_CAN_DO_ADMA1) {
429 val &= ~SDHCI_CAN_DO_ADMA1;
430 val |= SDHCI_CAN_DO_ADMA2;
431 }
432 }
433
434 if (unlikely(reg == SDHCI_CAPABILITIES_1)) {
435 if (esdhc_is_usdhc(imx_data)) {
436 if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1)
437 val = readl(host->ioaddr + SDHCI_CAPABILITIES) & 0xFFFF;
438 else
439 /* imx6q/dl does not have cap_1 register, fake one */
440 val = SDHCI_SUPPORT_DDR50 | SDHCI_SUPPORT_SDR104
441 | SDHCI_SUPPORT_SDR50
442 | SDHCI_USE_SDR50_TUNING
443 | FIELD_PREP(SDHCI_RETUNING_MODE_MASK,
444 SDHCI_TUNING_MODE_3);
445
446 if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
447 val |= SDHCI_SUPPORT_HS400;
448
449 /*
450 * Do not advertise faster UHS modes if there are no
451 * pinctrl states for 100MHz/200MHz.
452 */
453 if (IS_ERR_OR_NULL(imx_data->pins_100mhz) ||
454 IS_ERR_OR_NULL(imx_data->pins_200mhz))
455 val &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_DDR50
456 | SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_HS400);
457 }
458 }
459
460 if (unlikely(reg == SDHCI_MAX_CURRENT) && esdhc_is_usdhc(imx_data)) {
461 val = 0;
462 val |= FIELD_PREP(SDHCI_MAX_CURRENT_330_MASK, 0xFF);
463 val |= FIELD_PREP(SDHCI_MAX_CURRENT_300_MASK, 0xFF);
464 val |= FIELD_PREP(SDHCI_MAX_CURRENT_180_MASK, 0xFF);
465 }
466
467 if (unlikely(reg == SDHCI_INT_STATUS)) {
468 if (val & ESDHC_INT_VENDOR_SPEC_DMA_ERR) {
469 val &= ~ESDHC_INT_VENDOR_SPEC_DMA_ERR;
470 val |= SDHCI_INT_ADMA_ERROR;
471 }
472
473 /*
474 * mask off the interrupt we get in response to the manually
475 * sent CMD12
476 */
477 if ((imx_data->multiblock_status == WAIT_FOR_INT) &&
478 ((val & SDHCI_INT_RESPONSE) == SDHCI_INT_RESPONSE)) {
479 val &= ~SDHCI_INT_RESPONSE;
480 writel(SDHCI_INT_RESPONSE, host->ioaddr +
481 SDHCI_INT_STATUS);
482 imx_data->multiblock_status = NO_CMD_PENDING;
483 }
484 }
485
486 return val;
487}
488
489static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg)
490{
491 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
492 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
493 u32 data;
494
495 if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE ||
496 reg == SDHCI_INT_STATUS)) {
497 if ((val & SDHCI_INT_CARD_INT) && !esdhc_is_usdhc(imx_data)) {
498 /*
499 * Clear and then set D3CD bit to avoid missing the
500 * card interrupt. This is an eSDHC controller problem
501 * so we need to apply the following workaround: clear
502 * and set D3CD bit will make eSDHC re-sample the card
503 * interrupt. In case a card interrupt was lost,
504 * re-sample it by the following steps.
505 */
506 data = readl(host->ioaddr + SDHCI_HOST_CONTROL);
507 data &= ~ESDHC_CTRL_D3CD;
508 writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
509 data |= ESDHC_CTRL_D3CD;
510 writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
511 }
512
513 if (val & SDHCI_INT_ADMA_ERROR) {
514 val &= ~SDHCI_INT_ADMA_ERROR;
515 val |= ESDHC_INT_VENDOR_SPEC_DMA_ERR;
516 }
517 }
518
519 if (unlikely((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
520 && (reg == SDHCI_INT_STATUS)
521 && (val & SDHCI_INT_DATA_END))) {
522 u32 v;
523 v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
524 v &= ~ESDHC_VENDOR_SPEC_SDIO_QUIRK;
525 writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
526
527 if (imx_data->multiblock_status == MULTIBLK_IN_PROCESS)
528 {
529 /* send a manual CMD12 with RESPTYP=none */
530 data = MMC_STOP_TRANSMISSION << 24 |
531 SDHCI_CMD_ABORTCMD << 16;
532 writel(data, host->ioaddr + SDHCI_TRANSFER_MODE);
533 imx_data->multiblock_status = WAIT_FOR_INT;
534 }
535 }
536
537 writel(val, host->ioaddr + reg);
538}
539
540static u16 esdhc_readw_le(struct sdhci_host *host, int reg)
541{
542 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
543 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
544 u16 ret = 0;
545 u32 val;
546
547 if (unlikely(reg == SDHCI_HOST_VERSION)) {
548 reg ^= 2;
549 if (esdhc_is_usdhc(imx_data)) {
550 /*
551 * The usdhc register returns a wrong host version.
552 * Correct it here.
553 */
554 return SDHCI_SPEC_300;
555 }
556 }
557
558 if (unlikely(reg == SDHCI_HOST_CONTROL2)) {
559 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
560 if (val & ESDHC_VENDOR_SPEC_VSELECT)
561 ret |= SDHCI_CTRL_VDD_180;
562
563 if (esdhc_is_usdhc(imx_data)) {
564 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING)
565 val = readl(host->ioaddr + ESDHC_MIX_CTRL);
566 else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING)
567 /* the std tuning bits is in ACMD12_ERR for imx6sl */
568 val = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
569 }
570
571 if (val & ESDHC_MIX_CTRL_EXE_TUNE)
572 ret |= SDHCI_CTRL_EXEC_TUNING;
573 if (val & ESDHC_MIX_CTRL_SMPCLK_SEL)
574 ret |= SDHCI_CTRL_TUNED_CLK;
575
576 ret &= ~SDHCI_CTRL_PRESET_VAL_ENABLE;
577
578 return ret;
579 }
580
581 if (unlikely(reg == SDHCI_TRANSFER_MODE)) {
582 if (esdhc_is_usdhc(imx_data)) {
583 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
584 ret = m & ESDHC_MIX_CTRL_SDHCI_MASK;
585 /* Swap AC23 bit */
586 if (m & ESDHC_MIX_CTRL_AC23EN) {
587 ret &= ~ESDHC_MIX_CTRL_AC23EN;
588 ret |= SDHCI_TRNS_AUTO_CMD23;
589 }
590 } else {
591 ret = readw(host->ioaddr + SDHCI_TRANSFER_MODE);
592 }
593
594 return ret;
595 }
596
597 return readw(host->ioaddr + reg);
598}
599
600static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
601{
602 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
603 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
604 u32 new_val = 0;
605
606 switch (reg) {
607 case SDHCI_CLOCK_CONTROL:
608 new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
609 if (val & SDHCI_CLOCK_CARD_EN)
610 new_val |= ESDHC_VENDOR_SPEC_FRC_SDCLK_ON;
611 else
612 new_val &= ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON;
613 writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC);
614 if (!(new_val & ESDHC_VENDOR_SPEC_FRC_SDCLK_ON))
615 esdhc_wait_for_card_clock_gate_off(host);
616 return;
617 case SDHCI_HOST_CONTROL2:
618 new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
619 if (val & SDHCI_CTRL_VDD_180)
620 new_val |= ESDHC_VENDOR_SPEC_VSELECT;
621 else
622 new_val &= ~ESDHC_VENDOR_SPEC_VSELECT;
623 writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC);
624 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) {
625 new_val = readl(host->ioaddr + ESDHC_MIX_CTRL);
626 if (val & SDHCI_CTRL_TUNED_CLK) {
627 new_val |= ESDHC_MIX_CTRL_SMPCLK_SEL;
628 new_val |= ESDHC_MIX_CTRL_AUTO_TUNE_EN;
629 } else {
630 new_val &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
631 new_val &= ~ESDHC_MIX_CTRL_AUTO_TUNE_EN;
632 }
633 writel(new_val , host->ioaddr + ESDHC_MIX_CTRL);
634 } else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
635 u32 v = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
636 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
637 if (val & SDHCI_CTRL_TUNED_CLK) {
638 v |= ESDHC_MIX_CTRL_SMPCLK_SEL;
639 } else {
640 v &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
641 m &= ~ESDHC_MIX_CTRL_FBCLK_SEL;
642 m &= ~ESDHC_MIX_CTRL_AUTO_TUNE_EN;
643 }
644
645 if (val & SDHCI_CTRL_EXEC_TUNING) {
646 v |= ESDHC_MIX_CTRL_EXE_TUNE;
647 m |= ESDHC_MIX_CTRL_FBCLK_SEL;
648 m |= ESDHC_MIX_CTRL_AUTO_TUNE_EN;
649 } else {
650 v &= ~ESDHC_MIX_CTRL_EXE_TUNE;
651 }
652
653 writel(v, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
654 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
655 }
656 return;
657 case SDHCI_TRANSFER_MODE:
658 if ((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
659 && (host->cmd->opcode == SD_IO_RW_EXTENDED)
660 && (host->cmd->data->blocks > 1)
661 && (host->cmd->data->flags & MMC_DATA_READ)) {
662 u32 v;
663 v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
664 v |= ESDHC_VENDOR_SPEC_SDIO_QUIRK;
665 writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
666 }
667
668 if (esdhc_is_usdhc(imx_data)) {
669 u32 wml;
670 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
671 /* Swap AC23 bit */
672 if (val & SDHCI_TRNS_AUTO_CMD23) {
673 val &= ~SDHCI_TRNS_AUTO_CMD23;
674 val |= ESDHC_MIX_CTRL_AC23EN;
675 }
676 m = val | (m & ~ESDHC_MIX_CTRL_SDHCI_MASK);
677 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
678
679 /* Set watermark levels for PIO access to maximum value
680 * (128 words) to accommodate full 512 bytes buffer.
681 * For DMA access restore the levels to default value.
682 */
683 m = readl(host->ioaddr + ESDHC_WTMK_LVL);
684 if (val & SDHCI_TRNS_DMA) {
685 wml = ESDHC_WTMK_LVL_WML_VAL_DEF;
686 } else {
687 u8 ctrl;
688 wml = ESDHC_WTMK_LVL_WML_VAL_MAX;
689
690 /*
691 * Since already disable DMA mode, so also need
692 * to clear the DMASEL. Otherwise, for standard
693 * tuning, when send tuning command, usdhc will
694 * still prefetch the ADMA script from wrong
695 * DMA address, then we will see IOMMU report
696 * some error which show lack of TLB mapping.
697 */
698 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
699 ctrl &= ~SDHCI_CTRL_DMA_MASK;
700 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
701 }
702 m &= ~(ESDHC_WTMK_LVL_RD_WML_MASK |
703 ESDHC_WTMK_LVL_WR_WML_MASK);
704 m |= (wml << ESDHC_WTMK_LVL_RD_WML_SHIFT) |
705 (wml << ESDHC_WTMK_LVL_WR_WML_SHIFT);
706 writel(m, host->ioaddr + ESDHC_WTMK_LVL);
707 } else {
708 /*
709 * Postpone this write, we must do it together with a
710 * command write that is down below.
711 */
712 imx_data->scratchpad = val;
713 }
714 return;
715 case SDHCI_COMMAND:
716 if (host->cmd->opcode == MMC_STOP_TRANSMISSION)
717 val |= SDHCI_CMD_ABORTCMD;
718
719 if ((host->cmd->opcode == MMC_SET_BLOCK_COUNT) &&
720 (imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
721 imx_data->multiblock_status = MULTIBLK_IN_PROCESS;
722
723 if (esdhc_is_usdhc(imx_data))
724 writel(val << 16,
725 host->ioaddr + SDHCI_TRANSFER_MODE);
726 else
727 writel(val << 16 | imx_data->scratchpad,
728 host->ioaddr + SDHCI_TRANSFER_MODE);
729 return;
730 case SDHCI_BLOCK_SIZE:
731 val &= ~SDHCI_MAKE_BLKSZ(0x7, 0);
732 break;
733 }
734 esdhc_clrset_le(host, 0xffff, val, reg);
735}
736
737static u8 esdhc_readb_le(struct sdhci_host *host, int reg)
738{
739 u8 ret;
740 u32 val;
741
742 switch (reg) {
743 case SDHCI_HOST_CONTROL:
744 val = readl(host->ioaddr + reg);
745
746 ret = val & SDHCI_CTRL_LED;
747 ret |= (val >> 5) & SDHCI_CTRL_DMA_MASK;
748 ret |= (val & ESDHC_CTRL_4BITBUS);
749 ret |= (val & ESDHC_CTRL_8BITBUS) << 3;
750 return ret;
751 }
752
753 return readb(host->ioaddr + reg);
754}
755
756static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg)
757{
758 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
759 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
760 u32 new_val = 0;
761 u32 mask;
762
763 switch (reg) {
764 case SDHCI_POWER_CONTROL:
765 /*
766 * FSL put some DMA bits here
767 * If your board has a regulator, code should be here
768 */
769 return;
770 case SDHCI_HOST_CONTROL:
771 /* FSL messed up here, so we need to manually compose it. */
772 new_val = val & SDHCI_CTRL_LED;
773 /* ensure the endianness */
774 new_val |= ESDHC_HOST_CONTROL_LE;
775 /* bits 8&9 are reserved on mx25 */
776 if (!is_imx25_esdhc(imx_data)) {
777 /* DMA mode bits are shifted */
778 new_val |= (val & SDHCI_CTRL_DMA_MASK) << 5;
779 }
780
781 /*
782 * Do not touch buswidth bits here. This is done in
783 * esdhc_pltfm_bus_width.
784 * Do not touch the D3CD bit either which is used for the
785 * SDIO interrupt erratum workaround.
786 */
787 mask = 0xffff & ~(ESDHC_CTRL_BUSWIDTH_MASK | ESDHC_CTRL_D3CD);
788
789 esdhc_clrset_le(host, mask, new_val, reg);
790 return;
791 case SDHCI_SOFTWARE_RESET:
792 if (val & SDHCI_RESET_DATA)
793 new_val = readl(host->ioaddr + SDHCI_HOST_CONTROL);
794 break;
795 }
796 esdhc_clrset_le(host, 0xff, val, reg);
797
798 if (reg == SDHCI_SOFTWARE_RESET) {
799 if (val & SDHCI_RESET_ALL) {
800 /*
801 * The esdhc has a design violation to SDHC spec which
802 * tells that software reset should not affect card
803 * detection circuit. But esdhc clears its SYSCTL
804 * register bits [0..2] during the software reset. This
805 * will stop those clocks that card detection circuit
806 * relies on. To work around it, we turn the clocks on
807 * back to keep card detection circuit functional.
808 */
809 esdhc_clrset_le(host, 0x7, 0x7, ESDHC_SYSTEM_CONTROL);
810 /*
811 * The reset on usdhc fails to clear MIX_CTRL register.
812 * Do it manually here.
813 */
814 if (esdhc_is_usdhc(imx_data)) {
815 /*
816 * the tuning bits should be kept during reset
817 */
818 new_val = readl(host->ioaddr + ESDHC_MIX_CTRL);
819 writel(new_val & ESDHC_MIX_CTRL_TUNING_MASK,
820 host->ioaddr + ESDHC_MIX_CTRL);
821 imx_data->is_ddr = 0;
822 }
823 } else if (val & SDHCI_RESET_DATA) {
824 /*
825 * The eSDHC DAT line software reset clears at least the
826 * data transfer width on i.MX25, so make sure that the
827 * Host Control register is unaffected.
828 */
829 esdhc_clrset_le(host, 0xff, new_val,
830 SDHCI_HOST_CONTROL);
831 }
832 }
833}
834
835static unsigned int esdhc_pltfm_get_max_clock(struct sdhci_host *host)
836{
837 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
838
839 return pltfm_host->clock;
840}
841
842static unsigned int esdhc_pltfm_get_min_clock(struct sdhci_host *host)
843{
844 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
845
846 return pltfm_host->clock / 256 / 16;
847}
848
849static inline void esdhc_pltfm_set_clock(struct sdhci_host *host,
850 unsigned int clock)
851{
852 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
853 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
854 unsigned int host_clock = pltfm_host->clock;
855 int ddr_pre_div = imx_data->is_ddr ? 2 : 1;
856 int pre_div = 1;
857 int div = 1;
858 int ret;
859 u32 temp, val;
860
861 if (esdhc_is_usdhc(imx_data)) {
862 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
863 writel(val & ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
864 host->ioaddr + ESDHC_VENDOR_SPEC);
865 esdhc_wait_for_card_clock_gate_off(host);
866 }
867
868 if (clock == 0) {
869 host->mmc->actual_clock = 0;
870 return;
871 }
872
873 /* For i.MX53 eSDHCv3, SYSCTL.SDCLKFS may not be set to 0. */
874 if (is_imx53_esdhc(imx_data)) {
875 /*
876 * According to the i.MX53 reference manual, if DLLCTRL[10] can
877 * be set, then the controller is eSDHCv3, else it is eSDHCv2.
878 */
879 val = readl(host->ioaddr + ESDHC_DLL_CTRL);
880 writel(val | BIT(10), host->ioaddr + ESDHC_DLL_CTRL);
881 temp = readl(host->ioaddr + ESDHC_DLL_CTRL);
882 writel(val, host->ioaddr + ESDHC_DLL_CTRL);
883 if (temp & BIT(10))
884 pre_div = 2;
885 }
886
887 temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
888 temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
889 | ESDHC_CLOCK_MASK);
890 sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
891
892 if (imx_data->socdata->flags & ESDHC_FLAG_ERR010450) {
893 unsigned int max_clock;
894
895 max_clock = imx_data->is_ddr ? 45000000 : 150000000;
896
897 clock = min(clock, max_clock);
898 }
899
900 while (host_clock / (16 * pre_div * ddr_pre_div) > clock &&
901 pre_div < 256)
902 pre_div *= 2;
903
904 while (host_clock / (div * pre_div * ddr_pre_div) > clock && div < 16)
905 div++;
906
907 host->mmc->actual_clock = host_clock / (div * pre_div * ddr_pre_div);
908 dev_dbg(mmc_dev(host->mmc), "desired SD clock: %d, actual: %d\n",
909 clock, host->mmc->actual_clock);
910
911 pre_div >>= 1;
912 div--;
913
914 temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
915 temp |= (ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
916 | (div << ESDHC_DIVIDER_SHIFT)
917 | (pre_div << ESDHC_PREDIV_SHIFT));
918 sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
919
920 /* need to wait the bit 3 of the PRSSTAT to be set, make sure card clock is stable */
921 ret = readl_poll_timeout(host->ioaddr + ESDHC_PRSSTAT, temp,
922 (temp & ESDHC_CLOCK_STABLE), 2, 100);
923 if (ret == -ETIMEDOUT)
924 dev_warn(mmc_dev(host->mmc), "card clock still not stable in 100us!.\n");
925
926 if (esdhc_is_usdhc(imx_data)) {
927 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
928 writel(val | ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
929 host->ioaddr + ESDHC_VENDOR_SPEC);
930 }
931
932}
933
934static unsigned int esdhc_pltfm_get_ro(struct sdhci_host *host)
935{
936 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
937 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
938 struct esdhc_platform_data *boarddata = &imx_data->boarddata;
939
940 switch (boarddata->wp_type) {
941 case ESDHC_WP_GPIO:
942 return mmc_gpio_get_ro(host->mmc);
943 case ESDHC_WP_CONTROLLER:
944 return !(readl(host->ioaddr + SDHCI_PRESENT_STATE) &
945 SDHCI_WRITE_PROTECT);
946 case ESDHC_WP_NONE:
947 break;
948 }
949
950 return -ENOSYS;
951}
952
953static void esdhc_pltfm_set_bus_width(struct sdhci_host *host, int width)
954{
955 u32 ctrl;
956
957 switch (width) {
958 case MMC_BUS_WIDTH_8:
959 ctrl = ESDHC_CTRL_8BITBUS;
960 break;
961 case MMC_BUS_WIDTH_4:
962 ctrl = ESDHC_CTRL_4BITBUS;
963 break;
964 default:
965 ctrl = 0;
966 break;
967 }
968
969 esdhc_clrset_le(host, ESDHC_CTRL_BUSWIDTH_MASK, ctrl,
970 SDHCI_HOST_CONTROL);
971}
972
973static int usdhc_execute_tuning(struct mmc_host *mmc, u32 opcode)
974{
975 struct sdhci_host *host = mmc_priv(mmc);
976
977 /*
978 * i.MX uSDHC internally already uses a fixed optimized timing for
979 * DDR50, normally does not require tuning for DDR50 mode.
980 */
981 if (host->timing == MMC_TIMING_UHS_DDR50)
982 return 0;
983
984 return sdhci_execute_tuning(mmc, opcode);
985}
986
987static void esdhc_prepare_tuning(struct sdhci_host *host, u32 val)
988{
989 u32 reg;
990
991 /* FIXME: delay a bit for card to be ready for next tuning due to errors */
992 mdelay(1);
993
994 reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
995 reg |= ESDHC_MIX_CTRL_EXE_TUNE | ESDHC_MIX_CTRL_SMPCLK_SEL |
996 ESDHC_MIX_CTRL_FBCLK_SEL;
997 writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
998 writel(val << 8, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
999 dev_dbg(mmc_dev(host->mmc),
1000 "tuning with delay 0x%x ESDHC_TUNE_CTRL_STATUS 0x%x\n",
1001 val, readl(host->ioaddr + ESDHC_TUNE_CTRL_STATUS));
1002}
1003
1004static void esdhc_post_tuning(struct sdhci_host *host)
1005{
1006 u32 reg;
1007
1008 reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
1009 reg &= ~ESDHC_MIX_CTRL_EXE_TUNE;
1010 reg |= ESDHC_MIX_CTRL_AUTO_TUNE_EN;
1011 writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
1012}
1013
1014static int esdhc_executing_tuning(struct sdhci_host *host, u32 opcode)
1015{
1016 int min, max, avg, ret;
1017
1018 /* find the mininum delay first which can pass tuning */
1019 min = ESDHC_TUNE_CTRL_MIN;
1020 while (min < ESDHC_TUNE_CTRL_MAX) {
1021 esdhc_prepare_tuning(host, min);
1022 if (!mmc_send_tuning(host->mmc, opcode, NULL))
1023 break;
1024 min += ESDHC_TUNE_CTRL_STEP;
1025 }
1026
1027 /* find the maxinum delay which can not pass tuning */
1028 max = min + ESDHC_TUNE_CTRL_STEP;
1029 while (max < ESDHC_TUNE_CTRL_MAX) {
1030 esdhc_prepare_tuning(host, max);
1031 if (mmc_send_tuning(host->mmc, opcode, NULL)) {
1032 max -= ESDHC_TUNE_CTRL_STEP;
1033 break;
1034 }
1035 max += ESDHC_TUNE_CTRL_STEP;
1036 }
1037
1038 /* use average delay to get the best timing */
1039 avg = (min + max) / 2;
1040 esdhc_prepare_tuning(host, avg);
1041 ret = mmc_send_tuning(host->mmc, opcode, NULL);
1042 esdhc_post_tuning(host);
1043
1044 dev_dbg(mmc_dev(host->mmc), "tuning %s at 0x%x ret %d\n",
1045 ret ? "failed" : "passed", avg, ret);
1046
1047 return ret;
1048}
1049
1050static void esdhc_hs400_enhanced_strobe(struct mmc_host *mmc, struct mmc_ios *ios)
1051{
1052 struct sdhci_host *host = mmc_priv(mmc);
1053 u32 m;
1054
1055 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
1056 if (ios->enhanced_strobe)
1057 m |= ESDHC_MIX_CTRL_HS400_ES_EN;
1058 else
1059 m &= ~ESDHC_MIX_CTRL_HS400_ES_EN;
1060 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1061}
1062
1063static int esdhc_change_pinstate(struct sdhci_host *host,
1064 unsigned int uhs)
1065{
1066 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1067 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1068 struct pinctrl_state *pinctrl;
1069
1070 dev_dbg(mmc_dev(host->mmc), "change pinctrl state for uhs %d\n", uhs);
1071
1072 if (IS_ERR(imx_data->pinctrl) ||
1073 IS_ERR(imx_data->pins_100mhz) ||
1074 IS_ERR(imx_data->pins_200mhz))
1075 return -EINVAL;
1076
1077 switch (uhs) {
1078 case MMC_TIMING_UHS_SDR50:
1079 case MMC_TIMING_UHS_DDR50:
1080 pinctrl = imx_data->pins_100mhz;
1081 break;
1082 case MMC_TIMING_UHS_SDR104:
1083 case MMC_TIMING_MMC_HS200:
1084 case MMC_TIMING_MMC_HS400:
1085 pinctrl = imx_data->pins_200mhz;
1086 break;
1087 default:
1088 /* back to default state for other legacy timing */
1089 return pinctrl_select_default_state(mmc_dev(host->mmc));
1090 }
1091
1092 return pinctrl_select_state(imx_data->pinctrl, pinctrl);
1093}
1094
1095/*
1096 * For HS400 eMMC, there is a data_strobe line. This signal is generated
1097 * by the device and used for data output and CRC status response output
1098 * in HS400 mode. The frequency of this signal follows the frequency of
1099 * CLK generated by host. The host receives the data which is aligned to the
1100 * edge of data_strobe line. Due to the time delay between CLK line and
1101 * data_strobe line, if the delay time is larger than one clock cycle,
1102 * then CLK and data_strobe line will be misaligned, read error shows up.
1103 */
1104static void esdhc_set_strobe_dll(struct sdhci_host *host)
1105{
1106 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1107 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1108 u32 strobe_delay;
1109 u32 v;
1110 int ret;
1111
1112 /* disable clock before enabling strobe dll */
1113 writel(readl(host->ioaddr + ESDHC_VENDOR_SPEC) &
1114 ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
1115 host->ioaddr + ESDHC_VENDOR_SPEC);
1116 esdhc_wait_for_card_clock_gate_off(host);
1117
1118 /* force a reset on strobe dll */
1119 writel(ESDHC_STROBE_DLL_CTRL_RESET,
1120 host->ioaddr + ESDHC_STROBE_DLL_CTRL);
1121 /* clear the reset bit on strobe dll before any setting */
1122 writel(0, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
1123
1124 /*
1125 * enable strobe dll ctrl and adjust the delay target
1126 * for the uSDHC loopback read clock
1127 */
1128 if (imx_data->boarddata.strobe_dll_delay_target)
1129 strobe_delay = imx_data->boarddata.strobe_dll_delay_target;
1130 else
1131 strobe_delay = ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT;
1132 v = ESDHC_STROBE_DLL_CTRL_ENABLE |
1133 ESDHC_STROBE_DLL_CTRL_SLV_UPDATE_INT_DEFAULT |
1134 (strobe_delay << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT);
1135 writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
1136
1137 /* wait max 50us to get the REF/SLV lock */
1138 ret = readl_poll_timeout(host->ioaddr + ESDHC_STROBE_DLL_STATUS, v,
1139 ((v & ESDHC_STROBE_DLL_STS_REF_LOCK) && (v & ESDHC_STROBE_DLL_STS_SLV_LOCK)), 1, 50);
1140 if (ret == -ETIMEDOUT)
1141 dev_warn(mmc_dev(host->mmc),
1142 "warning! HS400 strobe DLL status REF/SLV not lock in 50us, STROBE DLL status is %x!\n", v);
1143}
1144
1145static void esdhc_reset_tuning(struct sdhci_host *host)
1146{
1147 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1148 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1149 u32 ctrl;
1150
1151 /* Reset the tuning circuit */
1152 if (esdhc_is_usdhc(imx_data)) {
1153 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) {
1154 ctrl = readl(host->ioaddr + ESDHC_MIX_CTRL);
1155 ctrl &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
1156 ctrl &= ~ESDHC_MIX_CTRL_FBCLK_SEL;
1157 writel(ctrl, host->ioaddr + ESDHC_MIX_CTRL);
1158 writel(0, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
1159 } else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
1160 ctrl = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
1161 ctrl &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
1162 writel(ctrl, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
1163 }
1164 }
1165}
1166
1167static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
1168{
1169 u32 m;
1170 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1171 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1172 struct esdhc_platform_data *boarddata = &imx_data->boarddata;
1173
1174 /* disable ddr mode and disable HS400 mode */
1175 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
1176 m &= ~(ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN);
1177 imx_data->is_ddr = 0;
1178
1179 switch (timing) {
1180 case MMC_TIMING_UHS_SDR12:
1181 case MMC_TIMING_UHS_SDR25:
1182 case MMC_TIMING_UHS_SDR50:
1183 case MMC_TIMING_UHS_SDR104:
1184 case MMC_TIMING_MMC_HS:
1185 case MMC_TIMING_MMC_HS200:
1186 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1187 break;
1188 case MMC_TIMING_UHS_DDR50:
1189 case MMC_TIMING_MMC_DDR52:
1190 m |= ESDHC_MIX_CTRL_DDREN;
1191 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1192 imx_data->is_ddr = 1;
1193 if (boarddata->delay_line) {
1194 u32 v;
1195 v = boarddata->delay_line <<
1196 ESDHC_DLL_OVERRIDE_VAL_SHIFT |
1197 (1 << ESDHC_DLL_OVERRIDE_EN_SHIFT);
1198 if (is_imx53_esdhc(imx_data))
1199 v <<= 1;
1200 writel(v, host->ioaddr + ESDHC_DLL_CTRL);
1201 }
1202 break;
1203 case MMC_TIMING_MMC_HS400:
1204 m |= ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN;
1205 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1206 imx_data->is_ddr = 1;
1207 /* update clock after enable DDR for strobe DLL lock */
1208 host->ops->set_clock(host, host->clock);
1209 esdhc_set_strobe_dll(host);
1210 break;
1211 case MMC_TIMING_LEGACY:
1212 default:
1213 esdhc_reset_tuning(host);
1214 break;
1215 }
1216
1217 esdhc_change_pinstate(host, timing);
1218}
1219
1220static void esdhc_reset(struct sdhci_host *host, u8 mask)
1221{
1222 sdhci_reset(host, mask);
1223
1224 sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
1225 sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
1226}
1227
1228static unsigned int esdhc_get_max_timeout_count(struct sdhci_host *host)
1229{
1230 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1231 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1232
1233 /* Doc Erratum: the uSDHC actual maximum timeout count is 1 << 29 */
1234 return esdhc_is_usdhc(imx_data) ? 1 << 29 : 1 << 27;
1235}
1236
1237static void esdhc_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
1238{
1239 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1240 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1241
1242 /* use maximum timeout counter */
1243 esdhc_clrset_le(host, ESDHC_SYS_CTRL_DTOCV_MASK,
1244 esdhc_is_usdhc(imx_data) ? 0xF : 0xE,
1245 SDHCI_TIMEOUT_CONTROL);
1246}
1247
1248static u32 esdhc_cqhci_irq(struct sdhci_host *host, u32 intmask)
1249{
1250 int cmd_error = 0;
1251 int data_error = 0;
1252
1253 if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error))
1254 return intmask;
1255
1256 cqhci_irq(host->mmc, intmask, cmd_error, data_error);
1257
1258 return 0;
1259}
1260
1261static struct sdhci_ops sdhci_esdhc_ops = {
1262 .read_l = esdhc_readl_le,
1263 .read_w = esdhc_readw_le,
1264 .read_b = esdhc_readb_le,
1265 .write_l = esdhc_writel_le,
1266 .write_w = esdhc_writew_le,
1267 .write_b = esdhc_writeb_le,
1268 .set_clock = esdhc_pltfm_set_clock,
1269 .get_max_clock = esdhc_pltfm_get_max_clock,
1270 .get_min_clock = esdhc_pltfm_get_min_clock,
1271 .get_max_timeout_count = esdhc_get_max_timeout_count,
1272 .get_ro = esdhc_pltfm_get_ro,
1273 .set_timeout = esdhc_set_timeout,
1274 .set_bus_width = esdhc_pltfm_set_bus_width,
1275 .set_uhs_signaling = esdhc_set_uhs_signaling,
1276 .reset = esdhc_reset,
1277 .irq = esdhc_cqhci_irq,
1278 .dump_vendor_regs = esdhc_dump_debug_regs,
1279};
1280
1281static const struct sdhci_pltfm_data sdhci_esdhc_imx_pdata = {
1282 .quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_NO_HISPD_BIT
1283 | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
1284 | SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC
1285 | SDHCI_QUIRK_BROKEN_CARD_DETECTION,
1286 .ops = &sdhci_esdhc_ops,
1287};
1288
1289static void sdhci_esdhc_imx_hwinit(struct sdhci_host *host)
1290{
1291 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1292 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1293 struct cqhci_host *cq_host = host->mmc->cqe_private;
1294 int tmp;
1295
1296 if (esdhc_is_usdhc(imx_data)) {
1297 /*
1298 * The imx6q ROM code will change the default watermark
1299 * level setting to something insane. Change it back here.
1300 */
1301 writel(ESDHC_WTMK_DEFAULT_VAL, host->ioaddr + ESDHC_WTMK_LVL);
1302
1303 /*
1304 * ROM code will change the bit burst_length_enable setting
1305 * to zero if this usdhc is chosen to boot system. Change
1306 * it back here, otherwise it will impact the performance a
1307 * lot. This bit is used to enable/disable the burst length
1308 * for the external AHB2AXI bridge. It's useful especially
1309 * for INCR transfer because without burst length indicator,
1310 * the AHB2AXI bridge does not know the burst length in
1311 * advance. And without burst length indicator, AHB INCR
1312 * transfer can only be converted to singles on the AXI side.
1313 */
1314 writel(readl(host->ioaddr + SDHCI_HOST_CONTROL)
1315 | ESDHC_BURST_LEN_EN_INCR,
1316 host->ioaddr + SDHCI_HOST_CONTROL);
1317
1318 /*
1319 * erratum ESDHC_FLAG_ERR004536 fix for MX6Q TO1.2 and MX6DL
1320 * TO1.1, it's harmless for MX6SL
1321 */
1322 writel(readl(host->ioaddr + 0x6c) & ~BIT(7),
1323 host->ioaddr + 0x6c);
1324
1325 /* disable DLL_CTRL delay line settings */
1326 writel(0x0, host->ioaddr + ESDHC_DLL_CTRL);
1327
1328 /*
1329 * For the case of command with busy, if set the bit
1330 * ESDHC_VEND_SPEC2_EN_BUSY_IRQ, USDHC will generate a
1331 * transfer complete interrupt when busy is deasserted.
1332 * When CQHCI use DCMD to send a CMD need R1b respons,
1333 * CQHCI require to set ESDHC_VEND_SPEC2_EN_BUSY_IRQ,
1334 * otherwise DCMD will always meet timeout waiting for
1335 * hardware interrupt issue.
1336 */
1337 if (imx_data->socdata->flags & ESDHC_FLAG_CQHCI) {
1338 tmp = readl(host->ioaddr + ESDHC_VEND_SPEC2);
1339 tmp |= ESDHC_VEND_SPEC2_EN_BUSY_IRQ;
1340 writel(tmp, host->ioaddr + ESDHC_VEND_SPEC2);
1341
1342 host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;
1343 }
1344
1345 if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
1346 tmp = readl(host->ioaddr + ESDHC_TUNING_CTRL);
1347 tmp |= ESDHC_STD_TUNING_EN |
1348 ESDHC_TUNING_START_TAP_DEFAULT;
1349 if (imx_data->boarddata.tuning_start_tap) {
1350 tmp &= ~ESDHC_TUNING_START_TAP_MASK;
1351 tmp |= imx_data->boarddata.tuning_start_tap;
1352 }
1353
1354 if (imx_data->boarddata.tuning_step) {
1355 tmp &= ~ESDHC_TUNING_STEP_MASK;
1356 tmp |= imx_data->boarddata.tuning_step
1357 << ESDHC_TUNING_STEP_SHIFT;
1358 }
1359
1360 /* Disable the CMD CRC check for tuning, if not, need to
1361 * add some delay after every tuning command, because
1362 * hardware standard tuning logic will directly go to next
1363 * step once it detect the CMD CRC error, will not wait for
1364 * the card side to finally send out the tuning data, trigger
1365 * the buffer read ready interrupt immediately. If usdhc send
1366 * the next tuning command some eMMC card will stuck, can't
1367 * response, block the tuning procedure or the first command
1368 * after the whole tuning procedure always can't get any response.
1369 */
1370 tmp |= ESDHC_TUNING_CMD_CRC_CHECK_DISABLE;
1371 writel(tmp, host->ioaddr + ESDHC_TUNING_CTRL);
1372 } else if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) {
1373 /*
1374 * ESDHC_STD_TUNING_EN may be configed in bootloader
1375 * or ROM code, so clear this bit here to make sure
1376 * the manual tuning can work.
1377 */
1378 tmp = readl(host->ioaddr + ESDHC_TUNING_CTRL);
1379 tmp &= ~ESDHC_STD_TUNING_EN;
1380 writel(tmp, host->ioaddr + ESDHC_TUNING_CTRL);
1381 }
1382
1383 /*
1384 * On i.MX8MM, we are running Dual Linux OS, with 1st Linux using SD Card
1385 * as rootfs storage, 2nd Linux using eMMC as rootfs storage. We let the
1386 * the 1st linux configure power/clock for the 2nd Linux.
1387 *
1388 * When the 2nd Linux is booting into rootfs stage, we let the 1st Linux
1389 * to destroy the 2nd linux, then restart the 2nd linux, we met SDHCI dump.
1390 * After we clear the pending interrupt and halt CQCTL, issue gone.
1391 */
1392 if (cq_host) {
1393 tmp = cqhci_readl(cq_host, CQHCI_IS);
1394 cqhci_writel(cq_host, tmp, CQHCI_IS);
1395 cqhci_writel(cq_host, CQHCI_HALT, CQHCI_CTL);
1396 }
1397 }
1398}
1399
1400static void esdhc_cqe_enable(struct mmc_host *mmc)
1401{
1402 struct sdhci_host *host = mmc_priv(mmc);
1403 struct cqhci_host *cq_host = mmc->cqe_private;
1404 u32 reg;
1405 u16 mode;
1406 int count = 10;
1407
1408 /*
1409 * CQE gets stuck if it sees Buffer Read Enable bit set, which can be
1410 * the case after tuning, so ensure the buffer is drained.
1411 */
1412 reg = sdhci_readl(host, SDHCI_PRESENT_STATE);
1413 while (reg & SDHCI_DATA_AVAILABLE) {
1414 sdhci_readl(host, SDHCI_BUFFER);
1415 reg = sdhci_readl(host, SDHCI_PRESENT_STATE);
1416 if (count-- == 0) {
1417 dev_warn(mmc_dev(host->mmc),
1418 "CQE may get stuck because the Buffer Read Enable bit is set\n");
1419 break;
1420 }
1421 mdelay(1);
1422 }
1423
1424 /*
1425 * Runtime resume will reset the entire host controller, which
1426 * will also clear the DMAEN/BCEN of register ESDHC_MIX_CTRL.
1427 * Here set DMAEN and BCEN when enable CMDQ.
1428 */
1429 mode = sdhci_readw(host, SDHCI_TRANSFER_MODE);
1430 if (host->flags & SDHCI_REQ_USE_DMA)
1431 mode |= SDHCI_TRNS_DMA;
1432 if (!(host->quirks2 & SDHCI_QUIRK2_SUPPORT_SINGLE))
1433 mode |= SDHCI_TRNS_BLK_CNT_EN;
1434 sdhci_writew(host, mode, SDHCI_TRANSFER_MODE);
1435
1436 /*
1437 * Though Runtime resume reset the entire host controller,
1438 * but do not impact the CQHCI side, need to clear the
1439 * HALT bit, avoid CQHCI stuck in the first request when
1440 * system resume back.
1441 */
1442 cqhci_writel(cq_host, 0, CQHCI_CTL);
1443 if (cqhci_readl(cq_host, CQHCI_CTL) && CQHCI_HALT)
1444 dev_err(mmc_dev(host->mmc),
1445 "failed to exit halt state when enable CQE\n");
1446
1447
1448 sdhci_cqe_enable(mmc);
1449}
1450
1451static void esdhc_sdhci_dumpregs(struct mmc_host *mmc)
1452{
1453 sdhci_dumpregs(mmc_priv(mmc));
1454}
1455
1456static const struct cqhci_host_ops esdhc_cqhci_ops = {
1457 .enable = esdhc_cqe_enable,
1458 .disable = sdhci_cqe_disable,
1459 .dumpregs = esdhc_sdhci_dumpregs,
1460};
1461
1462#ifdef CONFIG_OF
1463static int
1464sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
1465 struct sdhci_host *host,
1466 struct pltfm_imx_data *imx_data)
1467{
1468 struct device_node *np = pdev->dev.of_node;
1469 struct esdhc_platform_data *boarddata = &imx_data->boarddata;
1470 int ret;
1471
1472 if (of_get_property(np, "fsl,wp-controller", NULL))
1473 boarddata->wp_type = ESDHC_WP_CONTROLLER;
1474
1475 /*
1476 * If we have this property, then activate WP check.
1477 * Retrieveing and requesting the actual WP GPIO will happen
1478 * in the call to mmc_of_parse().
1479 */
1480 if (of_property_read_bool(np, "wp-gpios"))
1481 boarddata->wp_type = ESDHC_WP_GPIO;
1482
1483 of_property_read_u32(np, "fsl,tuning-step", &boarddata->tuning_step);
1484 of_property_read_u32(np, "fsl,tuning-start-tap",
1485 &boarddata->tuning_start_tap);
1486
1487 of_property_read_u32(np, "fsl,strobe-dll-delay-target",
1488 &boarddata->strobe_dll_delay_target);
1489 if (of_find_property(np, "no-1-8-v", NULL))
1490 host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V;
1491
1492 if (of_property_read_u32(np, "fsl,delay-line", &boarddata->delay_line))
1493 boarddata->delay_line = 0;
1494
1495 mmc_of_parse_voltage(np, &host->ocr_mask);
1496
1497 if (esdhc_is_usdhc(imx_data)) {
1498 imx_data->pins_100mhz = pinctrl_lookup_state(imx_data->pinctrl,
1499 ESDHC_PINCTRL_STATE_100MHZ);
1500 imx_data->pins_200mhz = pinctrl_lookup_state(imx_data->pinctrl,
1501 ESDHC_PINCTRL_STATE_200MHZ);
1502 }
1503
1504 /* call to generic mmc_of_parse to support additional capabilities */
1505 ret = mmc_of_parse(host->mmc);
1506 if (ret)
1507 return ret;
1508
1509 if (mmc_gpio_get_cd(host->mmc) >= 0)
1510 host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION;
1511
1512 return 0;
1513}
1514#else
1515static inline int
1516sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
1517 struct sdhci_host *host,
1518 struct pltfm_imx_data *imx_data)
1519{
1520 return -ENODEV;
1521}
1522#endif
1523
1524static int sdhci_esdhc_imx_probe_nondt(struct platform_device *pdev,
1525 struct sdhci_host *host,
1526 struct pltfm_imx_data *imx_data)
1527{
1528 struct esdhc_platform_data *boarddata = &imx_data->boarddata;
1529 int err;
1530
1531 if (!host->mmc->parent->platform_data) {
1532 dev_err(mmc_dev(host->mmc), "no board data!\n");
1533 return -EINVAL;
1534 }
1535
1536 imx_data->boarddata = *((struct esdhc_platform_data *)
1537 host->mmc->parent->platform_data);
1538 /* write_protect */
1539 if (boarddata->wp_type == ESDHC_WP_GPIO) {
1540 host->mmc->caps2 |= MMC_CAP2_RO_ACTIVE_HIGH;
1541
1542 err = mmc_gpiod_request_ro(host->mmc, "wp", 0, 0);
1543 if (err) {
1544 dev_err(mmc_dev(host->mmc),
1545 "failed to request write-protect gpio!\n");
1546 return err;
1547 }
1548 }
1549
1550 /* card_detect */
1551 switch (boarddata->cd_type) {
1552 case ESDHC_CD_GPIO:
1553 err = mmc_gpiod_request_cd(host->mmc, "cd", 0, false, 0);
1554 if (err) {
1555 dev_err(mmc_dev(host->mmc),
1556 "failed to request card-detect gpio!\n");
1557 return err;
1558 }
1559 fallthrough;
1560
1561 case ESDHC_CD_CONTROLLER:
1562 /* we have a working card_detect back */
1563 host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION;
1564 break;
1565
1566 case ESDHC_CD_PERMANENT:
1567 host->mmc->caps |= MMC_CAP_NONREMOVABLE;
1568 break;
1569
1570 case ESDHC_CD_NONE:
1571 break;
1572 }
1573
1574 switch (boarddata->max_bus_width) {
1575 case 8:
1576 host->mmc->caps |= MMC_CAP_8_BIT_DATA | MMC_CAP_4_BIT_DATA;
1577 break;
1578 case 4:
1579 host->mmc->caps |= MMC_CAP_4_BIT_DATA;
1580 break;
1581 case 1:
1582 default:
1583 host->quirks |= SDHCI_QUIRK_FORCE_1_BIT_DATA;
1584 break;
1585 }
1586
1587 return 0;
1588}
1589
1590static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
1591{
1592 const struct of_device_id *of_id =
1593 of_match_device(imx_esdhc_dt_ids, &pdev->dev);
1594 struct sdhci_pltfm_host *pltfm_host;
1595 struct sdhci_host *host;
1596 struct cqhci_host *cq_host;
1597 int err;
1598 struct pltfm_imx_data *imx_data;
1599
1600 host = sdhci_pltfm_init(pdev, &sdhci_esdhc_imx_pdata,
1601 sizeof(*imx_data));
1602 if (IS_ERR(host))
1603 return PTR_ERR(host);
1604
1605 pltfm_host = sdhci_priv(host);
1606
1607 imx_data = sdhci_pltfm_priv(pltfm_host);
1608
1609 imx_data->socdata = of_id ? of_id->data : (struct esdhc_soc_data *)
1610 pdev->id_entry->driver_data;
1611
1612 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1613 cpu_latency_qos_add_request(&imx_data->pm_qos_req, 0);
1614
1615 imx_data->clk_ipg = devm_clk_get(&pdev->dev, "ipg");
1616 if (IS_ERR(imx_data->clk_ipg)) {
1617 err = PTR_ERR(imx_data->clk_ipg);
1618 goto free_sdhci;
1619 }
1620
1621 imx_data->clk_ahb = devm_clk_get(&pdev->dev, "ahb");
1622 if (IS_ERR(imx_data->clk_ahb)) {
1623 err = PTR_ERR(imx_data->clk_ahb);
1624 goto free_sdhci;
1625 }
1626
1627 imx_data->clk_per = devm_clk_get(&pdev->dev, "per");
1628 if (IS_ERR(imx_data->clk_per)) {
1629 err = PTR_ERR(imx_data->clk_per);
1630 goto free_sdhci;
1631 }
1632
1633 pltfm_host->clk = imx_data->clk_per;
1634 pltfm_host->clock = clk_get_rate(pltfm_host->clk);
1635 err = clk_prepare_enable(imx_data->clk_per);
1636 if (err)
1637 goto free_sdhci;
1638 err = clk_prepare_enable(imx_data->clk_ipg);
1639 if (err)
1640 goto disable_per_clk;
1641 err = clk_prepare_enable(imx_data->clk_ahb);
1642 if (err)
1643 goto disable_ipg_clk;
1644
1645 imx_data->pinctrl = devm_pinctrl_get(&pdev->dev);
1646 if (IS_ERR(imx_data->pinctrl)) {
1647 err = PTR_ERR(imx_data->pinctrl);
1648 dev_warn(mmc_dev(host->mmc), "could not get pinctrl\n");
1649 }
1650
1651 if (esdhc_is_usdhc(imx_data)) {
1652 host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
1653 host->mmc->caps |= MMC_CAP_1_8V_DDR | MMC_CAP_3_3V_DDR;
1654
1655 /* GPIO CD can be set as a wakeup source */
1656 host->mmc->caps |= MMC_CAP_CD_WAKE;
1657
1658 if (!(imx_data->socdata->flags & ESDHC_FLAG_HS200))
1659 host->quirks2 |= SDHCI_QUIRK2_BROKEN_HS200;
1660
1661 /* clear tuning bits in case ROM has set it already */
1662 writel(0x0, host->ioaddr + ESDHC_MIX_CTRL);
1663 writel(0x0, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
1664 writel(0x0, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
1665
1666 /*
1667 * Link usdhc specific mmc_host_ops execute_tuning function,
1668 * to replace the standard one in sdhci_ops.
1669 */
1670 host->mmc_host_ops.execute_tuning = usdhc_execute_tuning;
1671 }
1672
1673 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING)
1674 sdhci_esdhc_ops.platform_execute_tuning =
1675 esdhc_executing_tuning;
1676
1677 if (imx_data->socdata->flags & ESDHC_FLAG_ERR004536)
1678 host->quirks |= SDHCI_QUIRK_BROKEN_ADMA;
1679
1680 if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
1681 host->quirks2 |= SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400;
1682
1683 if (imx_data->socdata->flags & ESDHC_FLAG_BROKEN_AUTO_CMD23)
1684 host->quirks2 |= SDHCI_QUIRK2_ACMD23_BROKEN;
1685
1686 if (imx_data->socdata->flags & ESDHC_FLAG_HS400_ES) {
1687 host->mmc->caps2 |= MMC_CAP2_HS400_ES;
1688 host->mmc_host_ops.hs400_enhanced_strobe =
1689 esdhc_hs400_enhanced_strobe;
1690 }
1691
1692 if (imx_data->socdata->flags & ESDHC_FLAG_CQHCI) {
1693 host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD;
1694 cq_host = devm_kzalloc(&pdev->dev, sizeof(*cq_host), GFP_KERNEL);
1695 if (!cq_host) {
1696 err = -ENOMEM;
1697 goto disable_ahb_clk;
1698 }
1699
1700 cq_host->mmio = host->ioaddr + ESDHC_CQHCI_ADDR_OFFSET;
1701 cq_host->ops = &esdhc_cqhci_ops;
1702
1703 err = cqhci_init(cq_host, host->mmc, false);
1704 if (err)
1705 goto disable_ahb_clk;
1706 }
1707
1708 if (of_id)
1709 err = sdhci_esdhc_imx_probe_dt(pdev, host, imx_data);
1710 else
1711 err = sdhci_esdhc_imx_probe_nondt(pdev, host, imx_data);
1712 if (err)
1713 goto disable_ahb_clk;
1714
1715 sdhci_esdhc_imx_hwinit(host);
1716
1717 err = sdhci_add_host(host);
1718 if (err)
1719 goto disable_ahb_clk;
1720
1721 pm_runtime_set_active(&pdev->dev);
1722 pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
1723 pm_runtime_use_autosuspend(&pdev->dev);
1724 pm_suspend_ignore_children(&pdev->dev, 1);
1725 pm_runtime_enable(&pdev->dev);
1726
1727 return 0;
1728
1729disable_ahb_clk:
1730 clk_disable_unprepare(imx_data->clk_ahb);
1731disable_ipg_clk:
1732 clk_disable_unprepare(imx_data->clk_ipg);
1733disable_per_clk:
1734 clk_disable_unprepare(imx_data->clk_per);
1735free_sdhci:
1736 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1737 cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1738 sdhci_pltfm_free(pdev);
1739 return err;
1740}
1741
1742static int sdhci_esdhc_imx_remove(struct platform_device *pdev)
1743{
1744 struct sdhci_host *host = platform_get_drvdata(pdev);
1745 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1746 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1747 int dead = (readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff);
1748
1749 pm_runtime_get_sync(&pdev->dev);
1750 pm_runtime_disable(&pdev->dev);
1751 pm_runtime_put_noidle(&pdev->dev);
1752
1753 sdhci_remove_host(host, dead);
1754
1755 clk_disable_unprepare(imx_data->clk_per);
1756 clk_disable_unprepare(imx_data->clk_ipg);
1757 clk_disable_unprepare(imx_data->clk_ahb);
1758
1759 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1760 cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1761
1762 sdhci_pltfm_free(pdev);
1763
1764 return 0;
1765}
1766
1767#ifdef CONFIG_PM_SLEEP
1768static int sdhci_esdhc_suspend(struct device *dev)
1769{
1770 struct sdhci_host *host = dev_get_drvdata(dev);
1771 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1772 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1773 int ret;
1774
1775 if (host->mmc->caps2 & MMC_CAP2_CQE) {
1776 ret = cqhci_suspend(host->mmc);
1777 if (ret)
1778 return ret;
1779 }
1780
1781 if ((imx_data->socdata->flags & ESDHC_FLAG_STATE_LOST_IN_LPMODE) &&
1782 (host->tuning_mode != SDHCI_TUNING_MODE_1)) {
1783 mmc_retune_timer_stop(host->mmc);
1784 mmc_retune_needed(host->mmc);
1785 }
1786
1787 if (host->tuning_mode != SDHCI_TUNING_MODE_3)
1788 mmc_retune_needed(host->mmc);
1789
1790 ret = sdhci_suspend_host(host);
1791 if (ret)
1792 return ret;
1793
1794 ret = pinctrl_pm_select_sleep_state(dev);
1795 if (ret)
1796 return ret;
1797
1798 ret = mmc_gpio_set_cd_wake(host->mmc, true);
1799
1800 return ret;
1801}
1802
1803static int sdhci_esdhc_resume(struct device *dev)
1804{
1805 struct sdhci_host *host = dev_get_drvdata(dev);
1806 int ret;
1807
1808 ret = pinctrl_pm_select_default_state(dev);
1809 if (ret)
1810 return ret;
1811
1812 /* re-initialize hw state in case it's lost in low power mode */
1813 sdhci_esdhc_imx_hwinit(host);
1814
1815 ret = sdhci_resume_host(host);
1816 if (ret)
1817 return ret;
1818
1819 if (host->mmc->caps2 & MMC_CAP2_CQE)
1820 ret = cqhci_resume(host->mmc);
1821
1822 if (!ret)
1823 ret = mmc_gpio_set_cd_wake(host->mmc, false);
1824
1825 return ret;
1826}
1827#endif
1828
1829#ifdef CONFIG_PM
1830static int sdhci_esdhc_runtime_suspend(struct device *dev)
1831{
1832 struct sdhci_host *host = dev_get_drvdata(dev);
1833 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1834 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1835 int ret;
1836
1837 if (host->mmc->caps2 & MMC_CAP2_CQE) {
1838 ret = cqhci_suspend(host->mmc);
1839 if (ret)
1840 return ret;
1841 }
1842
1843 ret = sdhci_runtime_suspend_host(host);
1844 if (ret)
1845 return ret;
1846
1847 if (host->tuning_mode != SDHCI_TUNING_MODE_3)
1848 mmc_retune_needed(host->mmc);
1849
1850 imx_data->actual_clock = host->mmc->actual_clock;
1851 esdhc_pltfm_set_clock(host, 0);
1852 clk_disable_unprepare(imx_data->clk_per);
1853 clk_disable_unprepare(imx_data->clk_ipg);
1854 clk_disable_unprepare(imx_data->clk_ahb);
1855
1856 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1857 cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1858
1859 return ret;
1860}
1861
1862static int sdhci_esdhc_runtime_resume(struct device *dev)
1863{
1864 struct sdhci_host *host = dev_get_drvdata(dev);
1865 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1866 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1867 int err;
1868
1869 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1870 cpu_latency_qos_add_request(&imx_data->pm_qos_req, 0);
1871
1872 if (imx_data->socdata->flags & ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME)
1873 clk_set_rate(imx_data->clk_per, pltfm_host->clock);
1874
1875 err = clk_prepare_enable(imx_data->clk_ahb);
1876 if (err)
1877 goto remove_pm_qos_request;
1878
1879 err = clk_prepare_enable(imx_data->clk_per);
1880 if (err)
1881 goto disable_ahb_clk;
1882
1883 err = clk_prepare_enable(imx_data->clk_ipg);
1884 if (err)
1885 goto disable_per_clk;
1886
1887 esdhc_pltfm_set_clock(host, imx_data->actual_clock);
1888
1889 err = sdhci_runtime_resume_host(host, 0);
1890 if (err)
1891 goto disable_ipg_clk;
1892
1893 if (host->mmc->caps2 & MMC_CAP2_CQE)
1894 err = cqhci_resume(host->mmc);
1895
1896 return err;
1897
1898disable_ipg_clk:
1899 clk_disable_unprepare(imx_data->clk_ipg);
1900disable_per_clk:
1901 clk_disable_unprepare(imx_data->clk_per);
1902disable_ahb_clk:
1903 clk_disable_unprepare(imx_data->clk_ahb);
1904remove_pm_qos_request:
1905 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1906 cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1907 return err;
1908}
1909#endif
1910
1911static const struct dev_pm_ops sdhci_esdhc_pmops = {
1912 SET_SYSTEM_SLEEP_PM_OPS(sdhci_esdhc_suspend, sdhci_esdhc_resume)
1913 SET_RUNTIME_PM_OPS(sdhci_esdhc_runtime_suspend,
1914 sdhci_esdhc_runtime_resume, NULL)
1915};
1916
1917static struct platform_driver sdhci_esdhc_imx_driver = {
1918 .driver = {
1919 .name = "sdhci-esdhc-imx",
1920 .of_match_table = imx_esdhc_dt_ids,
1921 .pm = &sdhci_esdhc_pmops,
1922 },
1923 .id_table = imx_esdhc_devtype,
1924 .probe = sdhci_esdhc_imx_probe,
1925 .remove = sdhci_esdhc_imx_remove,
1926};
1927
1928module_platform_driver(sdhci_esdhc_imx_driver);
1929
1930MODULE_DESCRIPTION("SDHCI driver for Freescale i.MX eSDHC");
1931MODULE_AUTHOR("Wolfram Sang <kernel@pengutronix.de>");
1932MODULE_LICENSE("GPL v2");