Loading...
1menu "Memory management options"
2
3config QUICKLIST
4 def_bool y
5
6config MMU
7 bool "Support for memory management hardware"
8 depends on !CPU_SH2
9 default y
10 help
11 Some SH processors (such as SH-2/SH-2A) lack an MMU. In order to
12 boot on these systems, this option must not be set.
13
14 On other systems (such as the SH-3 and 4) where an MMU exists,
15 turning this off will boot the kernel on these machines with the
16 MMU implicitly switched off.
17
18config PAGE_OFFSET
19 hex
20 default "0x80000000" if MMU && SUPERH32
21 default "0x20000000" if MMU && SUPERH64
22 default "0x00000000"
23
24config FORCE_MAX_ZONEORDER
25 int "Maximum zone order"
26 range 9 64 if PAGE_SIZE_16KB
27 default "9" if PAGE_SIZE_16KB
28 range 7 64 if PAGE_SIZE_64KB
29 default "7" if PAGE_SIZE_64KB
30 range 11 64
31 default "14" if !MMU
32 default "11"
33 help
34 The kernel memory allocator divides physically contiguous memory
35 blocks into "zones", where each zone is a power of two number of
36 pages. This option selects the largest power of two that the kernel
37 keeps in the memory allocator. If you need to allocate very large
38 blocks of physically contiguous memory, then you may need to
39 increase this value.
40
41 This config option is actually maximum order plus one. For example,
42 a value of 11 means that the largest free memory block is 2^10 pages.
43
44 The page size is not necessarily 4KB. Keep this in mind when
45 choosing a value for this option.
46
47config MEMORY_START
48 hex "Physical memory start address"
49 default "0x08000000"
50 ---help---
51 Computers built with Hitachi SuperH processors always
52 map the ROM starting at address zero. But the processor
53 does not specify the range that RAM takes.
54
55 The physical memory (RAM) start address will be automatically
56 set to 08000000. Other platforms, such as the Solution Engine
57 boards typically map RAM at 0C000000.
58
59 Tweak this only when porting to a new machine which does not
60 already have a defconfig. Changing it from the known correct
61 value on any of the known systems will only lead to disaster.
62
63config MEMORY_SIZE
64 hex "Physical memory size"
65 default "0x04000000"
66 help
67 This sets the default memory size assumed by your SH kernel. It can
68 be overridden as normal by the 'mem=' argument on the kernel command
69 line. If unsure, consult your board specifications or just leave it
70 as 0x04000000 which was the default value before this became
71 configurable.
72
73# Physical addressing modes
74
75config 29BIT
76 def_bool !32BIT
77 depends on SUPERH32
78 select UNCACHED_MAPPING
79
80config 32BIT
81 bool
82 default y if CPU_SH5 || !MMU
83
84config PMB
85 bool "Support 32-bit physical addressing through PMB"
86 depends on MMU && EXPERIMENTAL && CPU_SH4A && !CPU_SH4AL_DSP
87 select 32BIT
88 select UNCACHED_MAPPING
89 help
90 If you say Y here, physical addressing will be extended to
91 32-bits through the SH-4A PMB. If this is not set, legacy
92 29-bit physical addressing will be used.
93
94config X2TLB
95 def_bool y
96 depends on (CPU_SHX2 || CPU_SHX3) && MMU
97
98config VSYSCALL
99 bool "Support vsyscall page"
100 depends on MMU && (CPU_SH3 || CPU_SH4)
101 default y
102 help
103 This will enable support for the kernel mapping a vDSO page
104 in process space, and subsequently handing down the entry point
105 to the libc through the ELF auxiliary vector.
106
107 From the kernel side this is used for the signal trampoline.
108 For systems with an MMU that can afford to give up a page,
109 (the default value) say Y.
110
111config NUMA
112 bool "Non Uniform Memory Access (NUMA) Support"
113 depends on MMU && SYS_SUPPORTS_NUMA && EXPERIMENTAL
114 default n
115 help
116 Some SH systems have many various memories scattered around
117 the address space, each with varying latencies. This enables
118 support for these blocks by binding them to nodes and allowing
119 memory policies to be used for prioritizing and controlling
120 allocation behaviour.
121
122config NODES_SHIFT
123 int
124 default "3" if CPU_SUBTYPE_SHX3
125 default "1"
126 depends on NEED_MULTIPLE_NODES
127
128config ARCH_FLATMEM_ENABLE
129 def_bool y
130 depends on !NUMA
131
132config ARCH_SPARSEMEM_ENABLE
133 def_bool y
134 select SPARSEMEM_STATIC
135
136config ARCH_SPARSEMEM_DEFAULT
137 def_bool y
138
139config MAX_ACTIVE_REGIONS
140 int
141 default "6" if (CPU_SUBTYPE_SHX3 && SPARSEMEM)
142 default "2" if SPARSEMEM && (CPU_SUBTYPE_SH7722 || \
143 CPU_SUBTYPE_SH7785)
144 default "1"
145
146config ARCH_SELECT_MEMORY_MODEL
147 def_bool y
148
149config ARCH_ENABLE_MEMORY_HOTPLUG
150 def_bool y
151 depends on SPARSEMEM && MMU
152
153config ARCH_ENABLE_MEMORY_HOTREMOVE
154 def_bool y
155 depends on SPARSEMEM && MMU
156
157config ARCH_MEMORY_PROBE
158 def_bool y
159 depends on MEMORY_HOTPLUG
160
161config IOREMAP_FIXED
162 def_bool y
163 depends on X2TLB || SUPERH64
164
165config UNCACHED_MAPPING
166 bool
167
168config HAVE_SRAM_POOL
169 bool
170 select GENERIC_ALLOCATOR
171
172choice
173 prompt "Kernel page size"
174 default PAGE_SIZE_4KB
175
176config PAGE_SIZE_4KB
177 bool "4kB"
178 help
179 This is the default page size used by all SuperH CPUs.
180
181config PAGE_SIZE_8KB
182 bool "8kB"
183 depends on !MMU || X2TLB
184 help
185 This enables 8kB pages as supported by SH-X2 and later MMUs.
186
187config PAGE_SIZE_16KB
188 bool "16kB"
189 depends on !MMU
190 help
191 This enables 16kB pages on MMU-less SH systems.
192
193config PAGE_SIZE_64KB
194 bool "64kB"
195 depends on !MMU || CPU_SH4 || CPU_SH5
196 help
197 This enables support for 64kB pages, possible on all SH-4
198 CPUs and later.
199
200endchoice
201
202choice
203 prompt "HugeTLB page size"
204 depends on HUGETLB_PAGE
205 default HUGETLB_PAGE_SIZE_1MB if PAGE_SIZE_64KB
206 default HUGETLB_PAGE_SIZE_64K
207
208config HUGETLB_PAGE_SIZE_64K
209 bool "64kB"
210 depends on !PAGE_SIZE_64KB
211
212config HUGETLB_PAGE_SIZE_256K
213 bool "256kB"
214 depends on X2TLB
215
216config HUGETLB_PAGE_SIZE_1MB
217 bool "1MB"
218
219config HUGETLB_PAGE_SIZE_4MB
220 bool "4MB"
221 depends on X2TLB
222
223config HUGETLB_PAGE_SIZE_64MB
224 bool "64MB"
225 depends on X2TLB
226
227config HUGETLB_PAGE_SIZE_512MB
228 bool "512MB"
229 depends on CPU_SH5
230
231endchoice
232
233source "mm/Kconfig"
234
235config SCHED_MC
236 bool "Multi-core scheduler support"
237 depends on SMP
238 default y
239 help
240 Multi-core scheduler support improves the CPU scheduler's decision
241 making when dealing with multi-core CPU chips at a cost of slightly
242 increased overhead in some places. If unsure say N here.
243
244endmenu
245
246menu "Cache configuration"
247
248config SH7705_CACHE_32KB
249 bool "Enable 32KB cache size for SH7705"
250 depends on CPU_SUBTYPE_SH7705
251 default y
252
253choice
254 prompt "Cache mode"
255 default CACHE_WRITEBACK if CPU_SH2A || CPU_SH3 || CPU_SH4 || CPU_SH5
256 default CACHE_WRITETHROUGH if (CPU_SH2 && !CPU_SH2A)
257
258config CACHE_WRITEBACK
259 bool "Write-back"
260
261config CACHE_WRITETHROUGH
262 bool "Write-through"
263 help
264 Selecting this option will configure the caches in write-through
265 mode, as opposed to the default write-back configuration.
266
267 Since there's sill some aliasing issues on SH-4, this option will
268 unfortunately still require the majority of flushing functions to
269 be implemented to deal with aliasing.
270
271 If unsure, say N.
272
273config CACHE_OFF
274 bool "Off"
275
276endchoice
277
278endmenu
1# SPDX-License-Identifier: GPL-2.0
2menu "Memory management options"
3
4config MMU
5 bool "Support for memory management hardware"
6 depends on !CPU_SH2
7 default y
8 help
9 Some SH processors (such as SH-2/SH-2A) lack an MMU. In order to
10 boot on these systems, this option must not be set.
11
12 On other systems (such as the SH-3 and 4) where an MMU exists,
13 turning this off will boot the kernel on these machines with the
14 MMU implicitly switched off.
15
16config PAGE_OFFSET
17 hex
18 default "0x80000000" if MMU
19 default "0x00000000"
20
21config FORCE_MAX_ZONEORDER
22 int "Maximum zone order"
23 range 9 64 if PAGE_SIZE_16KB
24 default "9" if PAGE_SIZE_16KB
25 range 7 64 if PAGE_SIZE_64KB
26 default "7" if PAGE_SIZE_64KB
27 range 11 64
28 default "14" if !MMU
29 default "11"
30 help
31 The kernel memory allocator divides physically contiguous memory
32 blocks into "zones", where each zone is a power of two number of
33 pages. This option selects the largest power of two that the kernel
34 keeps in the memory allocator. If you need to allocate very large
35 blocks of physically contiguous memory, then you may need to
36 increase this value.
37
38 This config option is actually maximum order plus one. For example,
39 a value of 11 means that the largest free memory block is 2^10 pages.
40
41 The page size is not necessarily 4KB. Keep this in mind when
42 choosing a value for this option.
43
44config MEMORY_START
45 hex "Physical memory start address"
46 default "0x08000000"
47 help
48 Computers built with Hitachi SuperH processors always
49 map the ROM starting at address zero. But the processor
50 does not specify the range that RAM takes.
51
52 The physical memory (RAM) start address will be automatically
53 set to 08000000. Other platforms, such as the Solution Engine
54 boards typically map RAM at 0C000000.
55
56 Tweak this only when porting to a new machine which does not
57 already have a defconfig. Changing it from the known correct
58 value on any of the known systems will only lead to disaster.
59
60config MEMORY_SIZE
61 hex "Physical memory size"
62 default "0x04000000"
63 help
64 This sets the default memory size assumed by your SH kernel. It can
65 be overridden as normal by the 'mem=' argument on the kernel command
66 line. If unsure, consult your board specifications or just leave it
67 as 0x04000000 which was the default value before this became
68 configurable.
69
70# Physical addressing modes
71
72config 29BIT
73 def_bool !32BIT
74 select UNCACHED_MAPPING
75
76config 32BIT
77 bool
78 default !MMU
79
80config PMB
81 bool "Support 32-bit physical addressing through PMB"
82 depends on MMU && CPU_SH4A && !CPU_SH4AL_DSP
83 select 32BIT
84 select UNCACHED_MAPPING
85 help
86 If you say Y here, physical addressing will be extended to
87 32-bits through the SH-4A PMB. If this is not set, legacy
88 29-bit physical addressing will be used.
89
90config X2TLB
91 def_bool y
92 depends on (CPU_SHX2 || CPU_SHX3) && MMU
93
94config VSYSCALL
95 bool "Support vsyscall page"
96 depends on MMU && (CPU_SH3 || CPU_SH4)
97 default y
98 help
99 This will enable support for the kernel mapping a vDSO page
100 in process space, and subsequently handing down the entry point
101 to the libc through the ELF auxiliary vector.
102
103 From the kernel side this is used for the signal trampoline.
104 For systems with an MMU that can afford to give up a page,
105 (the default value) say Y.
106
107config NUMA
108 bool "Non-Uniform Memory Access (NUMA) Support"
109 depends on MMU && SYS_SUPPORTS_NUMA
110 select ARCH_WANT_NUMA_VARIABLE_LOCALITY
111 default n
112 help
113 Some SH systems have many various memories scattered around
114 the address space, each with varying latencies. This enables
115 support for these blocks by binding them to nodes and allowing
116 memory policies to be used for prioritizing and controlling
117 allocation behaviour.
118
119config NODES_SHIFT
120 int
121 default "3" if CPU_SUBTYPE_SHX3
122 default "1"
123 depends on NUMA
124
125config ARCH_FLATMEM_ENABLE
126 def_bool y
127 depends on !NUMA
128
129config ARCH_SPARSEMEM_ENABLE
130 def_bool y
131 select SPARSEMEM_STATIC
132
133config ARCH_SPARSEMEM_DEFAULT
134 def_bool y
135
136config ARCH_SELECT_MEMORY_MODEL
137 def_bool y
138
139config ARCH_MEMORY_PROBE
140 def_bool y
141 depends on MEMORY_HOTPLUG
142
143config IOREMAP_FIXED
144 def_bool y
145 depends on X2TLB
146
147config UNCACHED_MAPPING
148 bool
149
150config HAVE_SRAM_POOL
151 bool
152 select GENERIC_ALLOCATOR
153
154choice
155 prompt "Kernel page size"
156 default PAGE_SIZE_4KB
157
158config PAGE_SIZE_4KB
159 bool "4kB"
160 help
161 This is the default page size used by all SuperH CPUs.
162
163config PAGE_SIZE_8KB
164 bool "8kB"
165 depends on !MMU || X2TLB
166 help
167 This enables 8kB pages as supported by SH-X2 and later MMUs.
168
169config PAGE_SIZE_16KB
170 bool "16kB"
171 depends on !MMU
172 help
173 This enables 16kB pages on MMU-less SH systems.
174
175config PAGE_SIZE_64KB
176 bool "64kB"
177 depends on !MMU || CPU_SH4
178 help
179 This enables support for 64kB pages, possible on all SH-4
180 CPUs and later.
181
182endchoice
183
184choice
185 prompt "HugeTLB page size"
186 depends on HUGETLB_PAGE
187 default HUGETLB_PAGE_SIZE_1MB if PAGE_SIZE_64KB
188 default HUGETLB_PAGE_SIZE_64K
189
190config HUGETLB_PAGE_SIZE_64K
191 bool "64kB"
192 depends on !PAGE_SIZE_64KB
193
194config HUGETLB_PAGE_SIZE_256K
195 bool "256kB"
196 depends on X2TLB
197
198config HUGETLB_PAGE_SIZE_1MB
199 bool "1MB"
200
201config HUGETLB_PAGE_SIZE_4MB
202 bool "4MB"
203 depends on X2TLB
204
205config HUGETLB_PAGE_SIZE_64MB
206 bool "64MB"
207 depends on X2TLB
208
209endchoice
210
211config SCHED_MC
212 bool "Multi-core scheduler support"
213 depends on SMP
214 default y
215 help
216 Multi-core scheduler support improves the CPU scheduler's decision
217 making when dealing with multi-core CPU chips at a cost of slightly
218 increased overhead in some places. If unsure say N here.
219
220endmenu
221
222menu "Cache configuration"
223
224config SH7705_CACHE_32KB
225 bool "Enable 32KB cache size for SH7705"
226 depends on CPU_SUBTYPE_SH7705
227 default y
228
229choice
230 prompt "Cache mode"
231 default CACHE_WRITEBACK if CPU_SH2A || CPU_SH3 || CPU_SH4
232 default CACHE_WRITETHROUGH if (CPU_SH2 && !CPU_SH2A)
233
234config CACHE_WRITEBACK
235 bool "Write-back"
236
237config CACHE_WRITETHROUGH
238 bool "Write-through"
239 help
240 Selecting this option will configure the caches in write-through
241 mode, as opposed to the default write-back configuration.
242
243 Since there's sill some aliasing issues on SH-4, this option will
244 unfortunately still require the majority of flushing functions to
245 be implemented to deal with aliasing.
246
247 If unsure, say N.
248
249config CACHE_OFF
250 bool "Off"
251
252endchoice
253
254endmenu