Loading...
1/*
2 * Xilinx SPI controller driver (master mode only)
3 *
4 * Author: MontaVista Software, Inc.
5 * source@mvista.com
6 *
7 * Copyright (c) 2010 Secret Lab Technologies, Ltd.
8 * Copyright (c) 2009 Intel Corporation
9 * 2002-2007 (c) MontaVista Software, Inc.
10
11 * This program is free software; you can redistribute it and/or modify
12 * it under the terms of the GNU General Public License version 2 as
13 * published by the Free Software Foundation.
14 */
15
16#include <linux/module.h>
17#include <linux/init.h>
18#include <linux/interrupt.h>
19#include <linux/of.h>
20#include <linux/platform_device.h>
21#include <linux/spi/spi.h>
22#include <linux/spi/spi_bitbang.h>
23#include <linux/spi/xilinx_spi.h>
24#include <linux/io.h>
25
26#define XILINX_SPI_NAME "xilinx_spi"
27
28/* Register definitions as per "OPB Serial Peripheral Interface (SPI) (v1.00e)
29 * Product Specification", DS464
30 */
31#define XSPI_CR_OFFSET 0x60 /* Control Register */
32
33#define XSPI_CR_ENABLE 0x02
34#define XSPI_CR_MASTER_MODE 0x04
35#define XSPI_CR_CPOL 0x08
36#define XSPI_CR_CPHA 0x10
37#define XSPI_CR_MODE_MASK (XSPI_CR_CPHA | XSPI_CR_CPOL)
38#define XSPI_CR_TXFIFO_RESET 0x20
39#define XSPI_CR_RXFIFO_RESET 0x40
40#define XSPI_CR_MANUAL_SSELECT 0x80
41#define XSPI_CR_TRANS_INHIBIT 0x100
42#define XSPI_CR_LSB_FIRST 0x200
43
44#define XSPI_SR_OFFSET 0x64 /* Status Register */
45
46#define XSPI_SR_RX_EMPTY_MASK 0x01 /* Receive FIFO is empty */
47#define XSPI_SR_RX_FULL_MASK 0x02 /* Receive FIFO is full */
48#define XSPI_SR_TX_EMPTY_MASK 0x04 /* Transmit FIFO is empty */
49#define XSPI_SR_TX_FULL_MASK 0x08 /* Transmit FIFO is full */
50#define XSPI_SR_MODE_FAULT_MASK 0x10 /* Mode fault error */
51
52#define XSPI_TXD_OFFSET 0x68 /* Data Transmit Register */
53#define XSPI_RXD_OFFSET 0x6c /* Data Receive Register */
54
55#define XSPI_SSR_OFFSET 0x70 /* 32-bit Slave Select Register */
56
57/* Register definitions as per "OPB IPIF (v3.01c) Product Specification", DS414
58 * IPIF registers are 32 bit
59 */
60#define XIPIF_V123B_DGIER_OFFSET 0x1c /* IPIF global int enable reg */
61#define XIPIF_V123B_GINTR_ENABLE 0x80000000
62
63#define XIPIF_V123B_IISR_OFFSET 0x20 /* IPIF interrupt status reg */
64#define XIPIF_V123B_IIER_OFFSET 0x28 /* IPIF interrupt enable reg */
65
66#define XSPI_INTR_MODE_FAULT 0x01 /* Mode fault error */
67#define XSPI_INTR_SLAVE_MODE_FAULT 0x02 /* Selected as slave while
68 * disabled */
69#define XSPI_INTR_TX_EMPTY 0x04 /* TxFIFO is empty */
70#define XSPI_INTR_TX_UNDERRUN 0x08 /* TxFIFO was underrun */
71#define XSPI_INTR_RX_FULL 0x10 /* RxFIFO is full */
72#define XSPI_INTR_RX_OVERRUN 0x20 /* RxFIFO was overrun */
73#define XSPI_INTR_TX_HALF_EMPTY 0x40 /* TxFIFO is half empty */
74
75#define XIPIF_V123B_RESETR_OFFSET 0x40 /* IPIF reset register */
76#define XIPIF_V123B_RESET_MASK 0x0a /* the value to write */
77
78struct xilinx_spi {
79 /* bitbang has to be first */
80 struct spi_bitbang bitbang;
81 struct completion done;
82 struct resource mem; /* phys mem */
83 void __iomem *regs; /* virt. address of the control registers */
84
85 u32 irq;
86
87 u8 *rx_ptr; /* pointer in the Tx buffer */
88 const u8 *tx_ptr; /* pointer in the Rx buffer */
89 int remaining_bytes; /* the number of bytes left to transfer */
90 u8 bits_per_word;
91 unsigned int (*read_fn) (void __iomem *);
92 void (*write_fn) (u32, void __iomem *);
93 void (*tx_fn) (struct xilinx_spi *);
94 void (*rx_fn) (struct xilinx_spi *);
95};
96
97static void xspi_write32(u32 val, void __iomem *addr)
98{
99 iowrite32(val, addr);
100}
101
102static unsigned int xspi_read32(void __iomem *addr)
103{
104 return ioread32(addr);
105}
106
107static void xspi_write32_be(u32 val, void __iomem *addr)
108{
109 iowrite32be(val, addr);
110}
111
112static unsigned int xspi_read32_be(void __iomem *addr)
113{
114 return ioread32be(addr);
115}
116
117static void xspi_tx8(struct xilinx_spi *xspi)
118{
119 xspi->write_fn(*xspi->tx_ptr, xspi->regs + XSPI_TXD_OFFSET);
120 xspi->tx_ptr++;
121}
122
123static void xspi_tx16(struct xilinx_spi *xspi)
124{
125 xspi->write_fn(*(u16 *)(xspi->tx_ptr), xspi->regs + XSPI_TXD_OFFSET);
126 xspi->tx_ptr += 2;
127}
128
129static void xspi_tx32(struct xilinx_spi *xspi)
130{
131 xspi->write_fn(*(u32 *)(xspi->tx_ptr), xspi->regs + XSPI_TXD_OFFSET);
132 xspi->tx_ptr += 4;
133}
134
135static void xspi_rx8(struct xilinx_spi *xspi)
136{
137 u32 data = xspi->read_fn(xspi->regs + XSPI_RXD_OFFSET);
138 if (xspi->rx_ptr) {
139 *xspi->rx_ptr = data & 0xff;
140 xspi->rx_ptr++;
141 }
142}
143
144static void xspi_rx16(struct xilinx_spi *xspi)
145{
146 u32 data = xspi->read_fn(xspi->regs + XSPI_RXD_OFFSET);
147 if (xspi->rx_ptr) {
148 *(u16 *)(xspi->rx_ptr) = data & 0xffff;
149 xspi->rx_ptr += 2;
150 }
151}
152
153static void xspi_rx32(struct xilinx_spi *xspi)
154{
155 u32 data = xspi->read_fn(xspi->regs + XSPI_RXD_OFFSET);
156 if (xspi->rx_ptr) {
157 *(u32 *)(xspi->rx_ptr) = data;
158 xspi->rx_ptr += 4;
159 }
160}
161
162static void xspi_init_hw(struct xilinx_spi *xspi)
163{
164 void __iomem *regs_base = xspi->regs;
165
166 /* Reset the SPI device */
167 xspi->write_fn(XIPIF_V123B_RESET_MASK,
168 regs_base + XIPIF_V123B_RESETR_OFFSET);
169 /* Disable all the interrupts just in case */
170 xspi->write_fn(0, regs_base + XIPIF_V123B_IIER_OFFSET);
171 /* Enable the global IPIF interrupt */
172 xspi->write_fn(XIPIF_V123B_GINTR_ENABLE,
173 regs_base + XIPIF_V123B_DGIER_OFFSET);
174 /* Deselect the slave on the SPI bus */
175 xspi->write_fn(0xffff, regs_base + XSPI_SSR_OFFSET);
176 /* Disable the transmitter, enable Manual Slave Select Assertion,
177 * put SPI controller into master mode, and enable it */
178 xspi->write_fn(XSPI_CR_TRANS_INHIBIT | XSPI_CR_MANUAL_SSELECT |
179 XSPI_CR_MASTER_MODE | XSPI_CR_ENABLE | XSPI_CR_TXFIFO_RESET |
180 XSPI_CR_RXFIFO_RESET, regs_base + XSPI_CR_OFFSET);
181}
182
183static void xilinx_spi_chipselect(struct spi_device *spi, int is_on)
184{
185 struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
186
187 if (is_on == BITBANG_CS_INACTIVE) {
188 /* Deselect the slave on the SPI bus */
189 xspi->write_fn(0xffff, xspi->regs + XSPI_SSR_OFFSET);
190 } else if (is_on == BITBANG_CS_ACTIVE) {
191 /* Set the SPI clock phase and polarity */
192 u16 cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET)
193 & ~XSPI_CR_MODE_MASK;
194 if (spi->mode & SPI_CPHA)
195 cr |= XSPI_CR_CPHA;
196 if (spi->mode & SPI_CPOL)
197 cr |= XSPI_CR_CPOL;
198 xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
199
200 /* We do not check spi->max_speed_hz here as the SPI clock
201 * frequency is not software programmable (the IP block design
202 * parameter)
203 */
204
205 /* Activate the chip select */
206 xspi->write_fn(~(0x0001 << spi->chip_select),
207 xspi->regs + XSPI_SSR_OFFSET);
208 }
209}
210
211/* spi_bitbang requires custom setup_transfer() to be defined if there is a
212 * custom txrx_bufs(). We have nothing to setup here as the SPI IP block
213 * supports 8 or 16 bits per word which cannot be changed in software.
214 * SPI clock can't be changed in software either.
215 * Check for correct bits per word. Chip select delay calculations could be
216 * added here as soon as bitbang_work() can be made aware of the delay value.
217 */
218static int xilinx_spi_setup_transfer(struct spi_device *spi,
219 struct spi_transfer *t)
220{
221 struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
222 u8 bits_per_word;
223
224 bits_per_word = (t && t->bits_per_word)
225 ? t->bits_per_word : spi->bits_per_word;
226 if (bits_per_word != xspi->bits_per_word) {
227 dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n",
228 __func__, bits_per_word);
229 return -EINVAL;
230 }
231
232 return 0;
233}
234
235static int xilinx_spi_setup(struct spi_device *spi)
236{
237 /* always return 0, we can not check the number of bits.
238 * There are cases when SPI setup is called before any driver is
239 * there, in that case the SPI core defaults to 8 bits, which we
240 * do not support in some cases. But if we return an error, the
241 * SPI device would not be registered and no driver can get hold of it
242 * When the driver is there, it will call SPI setup again with the
243 * correct number of bits per transfer.
244 * If a driver setups with the wrong bit number, it will fail when
245 * it tries to do a transfer
246 */
247 return 0;
248}
249
250static void xilinx_spi_fill_tx_fifo(struct xilinx_spi *xspi)
251{
252 u8 sr;
253
254 /* Fill the Tx FIFO with as many bytes as possible */
255 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
256 while ((sr & XSPI_SR_TX_FULL_MASK) == 0 && xspi->remaining_bytes > 0) {
257 if (xspi->tx_ptr)
258 xspi->tx_fn(xspi);
259 else
260 xspi->write_fn(0, xspi->regs + XSPI_TXD_OFFSET);
261 xspi->remaining_bytes -= xspi->bits_per_word / 8;
262 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
263 }
264}
265
266static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
267{
268 struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
269 u32 ipif_ier;
270 u16 cr;
271
272 /* We get here with transmitter inhibited */
273
274 xspi->tx_ptr = t->tx_buf;
275 xspi->rx_ptr = t->rx_buf;
276 xspi->remaining_bytes = t->len;
277 INIT_COMPLETION(xspi->done);
278
279 xilinx_spi_fill_tx_fifo(xspi);
280
281 /* Enable the transmit empty interrupt, which we use to determine
282 * progress on the transmission.
283 */
284 ipif_ier = xspi->read_fn(xspi->regs + XIPIF_V123B_IIER_OFFSET);
285 xspi->write_fn(ipif_ier | XSPI_INTR_TX_EMPTY,
286 xspi->regs + XIPIF_V123B_IIER_OFFSET);
287
288 /* Start the transfer by not inhibiting the transmitter any longer */
289 cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET) &
290 ~XSPI_CR_TRANS_INHIBIT;
291 xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
292
293 wait_for_completion(&xspi->done);
294
295 /* Disable the transmit empty interrupt */
296 xspi->write_fn(ipif_ier, xspi->regs + XIPIF_V123B_IIER_OFFSET);
297
298 return t->len - xspi->remaining_bytes;
299}
300
301
302/* This driver supports single master mode only. Hence Tx FIFO Empty
303 * is the only interrupt we care about.
304 * Receive FIFO Overrun, Transmit FIFO Underrun, Mode Fault, and Slave Mode
305 * Fault are not to happen.
306 */
307static irqreturn_t xilinx_spi_irq(int irq, void *dev_id)
308{
309 struct xilinx_spi *xspi = dev_id;
310 u32 ipif_isr;
311
312 /* Get the IPIF interrupts, and clear them immediately */
313 ipif_isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET);
314 xspi->write_fn(ipif_isr, xspi->regs + XIPIF_V123B_IISR_OFFSET);
315
316 if (ipif_isr & XSPI_INTR_TX_EMPTY) { /* Transmission completed */
317 u16 cr;
318 u8 sr;
319
320 /* A transmit has just completed. Process received data and
321 * check for more data to transmit. Always inhibit the
322 * transmitter while the Isr refills the transmit register/FIFO,
323 * or make sure it is stopped if we're done.
324 */
325 cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
326 xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
327 xspi->regs + XSPI_CR_OFFSET);
328
329 /* Read out all the data from the Rx FIFO */
330 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
331 while ((sr & XSPI_SR_RX_EMPTY_MASK) == 0) {
332 xspi->rx_fn(xspi);
333 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
334 }
335
336 /* See if there is more data to send */
337 if (xspi->remaining_bytes > 0) {
338 xilinx_spi_fill_tx_fifo(xspi);
339 /* Start the transfer by not inhibiting the
340 * transmitter any longer
341 */
342 xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
343 } else {
344 /* No more data to send.
345 * Indicate the transfer is completed.
346 */
347 complete(&xspi->done);
348 }
349 }
350
351 return IRQ_HANDLED;
352}
353
354static const struct of_device_id xilinx_spi_of_match[] = {
355 { .compatible = "xlnx,xps-spi-2.00.a", },
356 { .compatible = "xlnx,xps-spi-2.00.b", },
357 {}
358};
359MODULE_DEVICE_TABLE(of, xilinx_spi_of_match);
360
361struct spi_master *xilinx_spi_init(struct device *dev, struct resource *mem,
362 u32 irq, s16 bus_num, int num_cs, int little_endian, int bits_per_word)
363{
364 struct spi_master *master;
365 struct xilinx_spi *xspi;
366 int ret;
367
368 master = spi_alloc_master(dev, sizeof(struct xilinx_spi));
369 if (!master)
370 return NULL;
371
372 /* the spi->mode bits understood by this driver: */
373 master->mode_bits = SPI_CPOL | SPI_CPHA;
374
375 xspi = spi_master_get_devdata(master);
376 xspi->bitbang.master = spi_master_get(master);
377 xspi->bitbang.chipselect = xilinx_spi_chipselect;
378 xspi->bitbang.setup_transfer = xilinx_spi_setup_transfer;
379 xspi->bitbang.txrx_bufs = xilinx_spi_txrx_bufs;
380 xspi->bitbang.master->setup = xilinx_spi_setup;
381 init_completion(&xspi->done);
382
383 if (!request_mem_region(mem->start, resource_size(mem),
384 XILINX_SPI_NAME))
385 goto put_master;
386
387 xspi->regs = ioremap(mem->start, resource_size(mem));
388 if (xspi->regs == NULL) {
389 dev_warn(dev, "ioremap failure\n");
390 goto map_failed;
391 }
392
393 master->bus_num = bus_num;
394 master->num_chipselect = num_cs;
395 master->dev.of_node = dev->of_node;
396
397 xspi->mem = *mem;
398 xspi->irq = irq;
399 if (little_endian) {
400 xspi->read_fn = xspi_read32;
401 xspi->write_fn = xspi_write32;
402 } else {
403 xspi->read_fn = xspi_read32_be;
404 xspi->write_fn = xspi_write32_be;
405 }
406 xspi->bits_per_word = bits_per_word;
407 if (xspi->bits_per_word == 8) {
408 xspi->tx_fn = xspi_tx8;
409 xspi->rx_fn = xspi_rx8;
410 } else if (xspi->bits_per_word == 16) {
411 xspi->tx_fn = xspi_tx16;
412 xspi->rx_fn = xspi_rx16;
413 } else if (xspi->bits_per_word == 32) {
414 xspi->tx_fn = xspi_tx32;
415 xspi->rx_fn = xspi_rx32;
416 } else
417 goto unmap_io;
418
419
420 /* SPI controller initializations */
421 xspi_init_hw(xspi);
422
423 /* Register for SPI Interrupt */
424 ret = request_irq(xspi->irq, xilinx_spi_irq, 0, XILINX_SPI_NAME, xspi);
425 if (ret)
426 goto unmap_io;
427
428 ret = spi_bitbang_start(&xspi->bitbang);
429 if (ret) {
430 dev_err(dev, "spi_bitbang_start FAILED\n");
431 goto free_irq;
432 }
433
434 dev_info(dev, "at 0x%08llX mapped to 0x%p, irq=%d\n",
435 (unsigned long long)mem->start, xspi->regs, xspi->irq);
436 return master;
437
438free_irq:
439 free_irq(xspi->irq, xspi);
440unmap_io:
441 iounmap(xspi->regs);
442map_failed:
443 release_mem_region(mem->start, resource_size(mem));
444put_master:
445 spi_master_put(master);
446 return NULL;
447}
448EXPORT_SYMBOL(xilinx_spi_init);
449
450void xilinx_spi_deinit(struct spi_master *master)
451{
452 struct xilinx_spi *xspi;
453
454 xspi = spi_master_get_devdata(master);
455
456 spi_bitbang_stop(&xspi->bitbang);
457 free_irq(xspi->irq, xspi);
458 iounmap(xspi->regs);
459
460 release_mem_region(xspi->mem.start, resource_size(&xspi->mem));
461 spi_master_put(xspi->bitbang.master);
462}
463EXPORT_SYMBOL(xilinx_spi_deinit);
464
465static int __devinit xilinx_spi_probe(struct platform_device *dev)
466{
467 struct xspi_platform_data *pdata;
468 struct resource *r;
469 int irq, num_cs = 0, little_endian = 0, bits_per_word = 8;
470 struct spi_master *master;
471 u8 i;
472
473 pdata = dev->dev.platform_data;
474 if (pdata) {
475 num_cs = pdata->num_chipselect;
476 little_endian = pdata->little_endian;
477 bits_per_word = pdata->bits_per_word;
478 }
479
480#ifdef CONFIG_OF
481 if (dev->dev.of_node) {
482 const __be32 *prop;
483 int len;
484
485 /* number of slave select bits is required */
486 prop = of_get_property(dev->dev.of_node, "xlnx,num-ss-bits",
487 &len);
488 if (prop && len >= sizeof(*prop))
489 num_cs = __be32_to_cpup(prop);
490 }
491#endif
492
493 if (!num_cs) {
494 dev_err(&dev->dev, "Missing slave select configuration data\n");
495 return -EINVAL;
496 }
497
498
499 r = platform_get_resource(dev, IORESOURCE_MEM, 0);
500 if (!r)
501 return -ENODEV;
502
503 irq = platform_get_irq(dev, 0);
504 if (irq < 0)
505 return -ENXIO;
506
507 master = xilinx_spi_init(&dev->dev, r, irq, dev->id, num_cs,
508 little_endian, bits_per_word);
509 if (!master)
510 return -ENODEV;
511
512 if (pdata) {
513 for (i = 0; i < pdata->num_devices; i++)
514 spi_new_device(master, pdata->devices + i);
515 }
516
517 platform_set_drvdata(dev, master);
518 return 0;
519}
520
521static int __devexit xilinx_spi_remove(struct platform_device *dev)
522{
523 xilinx_spi_deinit(platform_get_drvdata(dev));
524 platform_set_drvdata(dev, 0);
525
526 return 0;
527}
528
529/* work with hotplug and coldplug */
530MODULE_ALIAS("platform:" XILINX_SPI_NAME);
531
532static struct platform_driver xilinx_spi_driver = {
533 .probe = xilinx_spi_probe,
534 .remove = __devexit_p(xilinx_spi_remove),
535 .driver = {
536 .name = XILINX_SPI_NAME,
537 .owner = THIS_MODULE,
538 .of_match_table = xilinx_spi_of_match,
539 },
540};
541module_platform_driver(xilinx_spi_driver);
542
543MODULE_AUTHOR("MontaVista Software, Inc. <source@mvista.com>");
544MODULE_DESCRIPTION("Xilinx SPI driver");
545MODULE_LICENSE("GPL");
1/*
2 * Xilinx SPI controller driver (master mode only)
3 *
4 * Author: MontaVista Software, Inc.
5 * source@mvista.com
6 *
7 * Copyright (c) 2010 Secret Lab Technologies, Ltd.
8 * Copyright (c) 2009 Intel Corporation
9 * 2002-2007 (c) MontaVista Software, Inc.
10
11 * This program is free software; you can redistribute it and/or modify
12 * it under the terms of the GNU General Public License version 2 as
13 * published by the Free Software Foundation.
14 */
15
16#include <linux/module.h>
17#include <linux/interrupt.h>
18#include <linux/of.h>
19#include <linux/platform_device.h>
20#include <linux/spi/spi.h>
21#include <linux/spi/spi_bitbang.h>
22#include <linux/spi/xilinx_spi.h>
23#include <linux/io.h>
24
25#define XILINX_SPI_MAX_CS 32
26
27#define XILINX_SPI_NAME "xilinx_spi"
28
29/* Register definitions as per "OPB Serial Peripheral Interface (SPI) (v1.00e)
30 * Product Specification", DS464
31 */
32#define XSPI_CR_OFFSET 0x60 /* Control Register */
33
34#define XSPI_CR_LOOP 0x01
35#define XSPI_CR_ENABLE 0x02
36#define XSPI_CR_MASTER_MODE 0x04
37#define XSPI_CR_CPOL 0x08
38#define XSPI_CR_CPHA 0x10
39#define XSPI_CR_MODE_MASK (XSPI_CR_CPHA | XSPI_CR_CPOL | \
40 XSPI_CR_LSB_FIRST | XSPI_CR_LOOP)
41#define XSPI_CR_TXFIFO_RESET 0x20
42#define XSPI_CR_RXFIFO_RESET 0x40
43#define XSPI_CR_MANUAL_SSELECT 0x80
44#define XSPI_CR_TRANS_INHIBIT 0x100
45#define XSPI_CR_LSB_FIRST 0x200
46
47#define XSPI_SR_OFFSET 0x64 /* Status Register */
48
49#define XSPI_SR_RX_EMPTY_MASK 0x01 /* Receive FIFO is empty */
50#define XSPI_SR_RX_FULL_MASK 0x02 /* Receive FIFO is full */
51#define XSPI_SR_TX_EMPTY_MASK 0x04 /* Transmit FIFO is empty */
52#define XSPI_SR_TX_FULL_MASK 0x08 /* Transmit FIFO is full */
53#define XSPI_SR_MODE_FAULT_MASK 0x10 /* Mode fault error */
54
55#define XSPI_TXD_OFFSET 0x68 /* Data Transmit Register */
56#define XSPI_RXD_OFFSET 0x6c /* Data Receive Register */
57
58#define XSPI_SSR_OFFSET 0x70 /* 32-bit Slave Select Register */
59
60/* Register definitions as per "OPB IPIF (v3.01c) Product Specification", DS414
61 * IPIF registers are 32 bit
62 */
63#define XIPIF_V123B_DGIER_OFFSET 0x1c /* IPIF global int enable reg */
64#define XIPIF_V123B_GINTR_ENABLE 0x80000000
65
66#define XIPIF_V123B_IISR_OFFSET 0x20 /* IPIF interrupt status reg */
67#define XIPIF_V123B_IIER_OFFSET 0x28 /* IPIF interrupt enable reg */
68
69#define XSPI_INTR_MODE_FAULT 0x01 /* Mode fault error */
70#define XSPI_INTR_SLAVE_MODE_FAULT 0x02 /* Selected as slave while
71 * disabled */
72#define XSPI_INTR_TX_EMPTY 0x04 /* TxFIFO is empty */
73#define XSPI_INTR_TX_UNDERRUN 0x08 /* TxFIFO was underrun */
74#define XSPI_INTR_RX_FULL 0x10 /* RxFIFO is full */
75#define XSPI_INTR_RX_OVERRUN 0x20 /* RxFIFO was overrun */
76#define XSPI_INTR_TX_HALF_EMPTY 0x40 /* TxFIFO is half empty */
77
78#define XIPIF_V123B_RESETR_OFFSET 0x40 /* IPIF reset register */
79#define XIPIF_V123B_RESET_MASK 0x0a /* the value to write */
80
81struct xilinx_spi {
82 /* bitbang has to be first */
83 struct spi_bitbang bitbang;
84 struct completion done;
85 void __iomem *regs; /* virt. address of the control registers */
86
87 int irq;
88
89 u8 *rx_ptr; /* pointer in the Tx buffer */
90 const u8 *tx_ptr; /* pointer in the Rx buffer */
91 u8 bytes_per_word;
92 int buffer_size; /* buffer size in words */
93 u32 cs_inactive; /* Level of the CS pins when inactive*/
94 unsigned int (*read_fn)(void __iomem *);
95 void (*write_fn)(u32, void __iomem *);
96};
97
98static void xspi_write32(u32 val, void __iomem *addr)
99{
100 iowrite32(val, addr);
101}
102
103static unsigned int xspi_read32(void __iomem *addr)
104{
105 return ioread32(addr);
106}
107
108static void xspi_write32_be(u32 val, void __iomem *addr)
109{
110 iowrite32be(val, addr);
111}
112
113static unsigned int xspi_read32_be(void __iomem *addr)
114{
115 return ioread32be(addr);
116}
117
118static void xilinx_spi_tx(struct xilinx_spi *xspi)
119{
120 u32 data = 0;
121
122 if (!xspi->tx_ptr) {
123 xspi->write_fn(0, xspi->regs + XSPI_TXD_OFFSET);
124 return;
125 }
126
127 switch (xspi->bytes_per_word) {
128 case 1:
129 data = *(u8 *)(xspi->tx_ptr);
130 break;
131 case 2:
132 data = *(u16 *)(xspi->tx_ptr);
133 break;
134 case 4:
135 data = *(u32 *)(xspi->tx_ptr);
136 break;
137 }
138
139 xspi->write_fn(data, xspi->regs + XSPI_TXD_OFFSET);
140 xspi->tx_ptr += xspi->bytes_per_word;
141}
142
143static void xilinx_spi_rx(struct xilinx_spi *xspi)
144{
145 u32 data = xspi->read_fn(xspi->regs + XSPI_RXD_OFFSET);
146
147 if (!xspi->rx_ptr)
148 return;
149
150 switch (xspi->bytes_per_word) {
151 case 1:
152 *(u8 *)(xspi->rx_ptr) = data;
153 break;
154 case 2:
155 *(u16 *)(xspi->rx_ptr) = data;
156 break;
157 case 4:
158 *(u32 *)(xspi->rx_ptr) = data;
159 break;
160 }
161
162 xspi->rx_ptr += xspi->bytes_per_word;
163}
164
165static void xspi_init_hw(struct xilinx_spi *xspi)
166{
167 void __iomem *regs_base = xspi->regs;
168
169 /* Reset the SPI device */
170 xspi->write_fn(XIPIF_V123B_RESET_MASK,
171 regs_base + XIPIF_V123B_RESETR_OFFSET);
172 /* Enable the transmit empty interrupt, which we use to determine
173 * progress on the transmission.
174 */
175 xspi->write_fn(XSPI_INTR_TX_EMPTY,
176 regs_base + XIPIF_V123B_IIER_OFFSET);
177 /* Disable the global IPIF interrupt */
178 xspi->write_fn(0, regs_base + XIPIF_V123B_DGIER_OFFSET);
179 /* Deselect the slave on the SPI bus */
180 xspi->write_fn(0xffff, regs_base + XSPI_SSR_OFFSET);
181 /* Disable the transmitter, enable Manual Slave Select Assertion,
182 * put SPI controller into master mode, and enable it */
183 xspi->write_fn(XSPI_CR_MANUAL_SSELECT | XSPI_CR_MASTER_MODE |
184 XSPI_CR_ENABLE | XSPI_CR_TXFIFO_RESET | XSPI_CR_RXFIFO_RESET,
185 regs_base + XSPI_CR_OFFSET);
186}
187
188static void xilinx_spi_chipselect(struct spi_device *spi, int is_on)
189{
190 struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
191 u16 cr;
192 u32 cs;
193
194 if (is_on == BITBANG_CS_INACTIVE) {
195 /* Deselect the slave on the SPI bus */
196 xspi->write_fn(xspi->cs_inactive, xspi->regs + XSPI_SSR_OFFSET);
197 return;
198 }
199
200 /* Set the SPI clock phase and polarity */
201 cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET) & ~XSPI_CR_MODE_MASK;
202 if (spi->mode & SPI_CPHA)
203 cr |= XSPI_CR_CPHA;
204 if (spi->mode & SPI_CPOL)
205 cr |= XSPI_CR_CPOL;
206 if (spi->mode & SPI_LSB_FIRST)
207 cr |= XSPI_CR_LSB_FIRST;
208 if (spi->mode & SPI_LOOP)
209 cr |= XSPI_CR_LOOP;
210 xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
211
212 /* We do not check spi->max_speed_hz here as the SPI clock
213 * frequency is not software programmable (the IP block design
214 * parameter)
215 */
216
217 cs = xspi->cs_inactive;
218 cs ^= BIT(spi->chip_select);
219
220 /* Activate the chip select */
221 xspi->write_fn(cs, xspi->regs + XSPI_SSR_OFFSET);
222}
223
224/* spi_bitbang requires custom setup_transfer() to be defined if there is a
225 * custom txrx_bufs().
226 */
227static int xilinx_spi_setup_transfer(struct spi_device *spi,
228 struct spi_transfer *t)
229{
230 struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
231
232 if (spi->mode & SPI_CS_HIGH)
233 xspi->cs_inactive &= ~BIT(spi->chip_select);
234 else
235 xspi->cs_inactive |= BIT(spi->chip_select);
236
237 return 0;
238}
239
240static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
241{
242 struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
243 int remaining_words; /* the number of words left to transfer */
244 bool use_irq = false;
245 u16 cr = 0;
246
247 /* We get here with transmitter inhibited */
248
249 xspi->tx_ptr = t->tx_buf;
250 xspi->rx_ptr = t->rx_buf;
251 remaining_words = t->len / xspi->bytes_per_word;
252
253 if (xspi->irq >= 0 && remaining_words > xspi->buffer_size) {
254 u32 isr;
255 use_irq = true;
256 /* Inhibit irq to avoid spurious irqs on tx_empty*/
257 cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
258 xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
259 xspi->regs + XSPI_CR_OFFSET);
260 /* ACK old irqs (if any) */
261 isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET);
262 if (isr)
263 xspi->write_fn(isr,
264 xspi->regs + XIPIF_V123B_IISR_OFFSET);
265 /* Enable the global IPIF interrupt */
266 xspi->write_fn(XIPIF_V123B_GINTR_ENABLE,
267 xspi->regs + XIPIF_V123B_DGIER_OFFSET);
268 reinit_completion(&xspi->done);
269 }
270
271 while (remaining_words) {
272 int n_words, tx_words, rx_words;
273 u32 sr;
274
275 n_words = min(remaining_words, xspi->buffer_size);
276
277 tx_words = n_words;
278 while (tx_words--)
279 xilinx_spi_tx(xspi);
280
281 /* Start the transfer by not inhibiting the transmitter any
282 * longer
283 */
284
285 if (use_irq) {
286 xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
287 wait_for_completion(&xspi->done);
288 /* A transmit has just completed. Process received data
289 * and check for more data to transmit. Always inhibit
290 * the transmitter while the Isr refills the transmit
291 * register/FIFO, or make sure it is stopped if we're
292 * done.
293 */
294 xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
295 xspi->regs + XSPI_CR_OFFSET);
296 sr = XSPI_SR_TX_EMPTY_MASK;
297 } else
298 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
299
300 /* Read out all the data from the Rx FIFO */
301 rx_words = n_words;
302 while (rx_words) {
303 if ((sr & XSPI_SR_TX_EMPTY_MASK) && (rx_words > 1)) {
304 xilinx_spi_rx(xspi);
305 rx_words--;
306 continue;
307 }
308
309 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
310 if (!(sr & XSPI_SR_RX_EMPTY_MASK)) {
311 xilinx_spi_rx(xspi);
312 rx_words--;
313 }
314 }
315
316 remaining_words -= n_words;
317 }
318
319 if (use_irq) {
320 xspi->write_fn(0, xspi->regs + XIPIF_V123B_DGIER_OFFSET);
321 xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
322 }
323
324 return t->len;
325}
326
327
328/* This driver supports single master mode only. Hence Tx FIFO Empty
329 * is the only interrupt we care about.
330 * Receive FIFO Overrun, Transmit FIFO Underrun, Mode Fault, and Slave Mode
331 * Fault are not to happen.
332 */
333static irqreturn_t xilinx_spi_irq(int irq, void *dev_id)
334{
335 struct xilinx_spi *xspi = dev_id;
336 u32 ipif_isr;
337
338 /* Get the IPIF interrupts, and clear them immediately */
339 ipif_isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET);
340 xspi->write_fn(ipif_isr, xspi->regs + XIPIF_V123B_IISR_OFFSET);
341
342 if (ipif_isr & XSPI_INTR_TX_EMPTY) { /* Transmission completed */
343 complete(&xspi->done);
344 }
345
346 return IRQ_HANDLED;
347}
348
349static int xilinx_spi_find_buffer_size(struct xilinx_spi *xspi)
350{
351 u8 sr;
352 int n_words = 0;
353
354 /*
355 * Before the buffer_size detection we reset the core
356 * to make sure we start with a clean state.
357 */
358 xspi->write_fn(XIPIF_V123B_RESET_MASK,
359 xspi->regs + XIPIF_V123B_RESETR_OFFSET);
360
361 /* Fill the Tx FIFO with as many words as possible */
362 do {
363 xspi->write_fn(0, xspi->regs + XSPI_TXD_OFFSET);
364 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
365 n_words++;
366 } while (!(sr & XSPI_SR_TX_FULL_MASK));
367
368 return n_words;
369}
370
371static const struct of_device_id xilinx_spi_of_match[] = {
372 { .compatible = "xlnx,xps-spi-2.00.a", },
373 { .compatible = "xlnx,xps-spi-2.00.b", },
374 {}
375};
376MODULE_DEVICE_TABLE(of, xilinx_spi_of_match);
377
378static int xilinx_spi_probe(struct platform_device *pdev)
379{
380 struct xilinx_spi *xspi;
381 struct xspi_platform_data *pdata;
382 struct resource *res;
383 int ret, num_cs = 0, bits_per_word = 8;
384 struct spi_master *master;
385 u32 tmp;
386 u8 i;
387
388 pdata = dev_get_platdata(&pdev->dev);
389 if (pdata) {
390 num_cs = pdata->num_chipselect;
391 bits_per_word = pdata->bits_per_word;
392 } else {
393 of_property_read_u32(pdev->dev.of_node, "xlnx,num-ss-bits",
394 &num_cs);
395 }
396
397 if (!num_cs) {
398 dev_err(&pdev->dev,
399 "Missing slave select configuration data\n");
400 return -EINVAL;
401 }
402
403 if (num_cs > XILINX_SPI_MAX_CS) {
404 dev_err(&pdev->dev, "Invalid number of spi slaves\n");
405 return -EINVAL;
406 }
407
408 master = spi_alloc_master(&pdev->dev, sizeof(struct xilinx_spi));
409 if (!master)
410 return -ENODEV;
411
412 /* the spi->mode bits understood by this driver: */
413 master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST | SPI_LOOP |
414 SPI_CS_HIGH;
415
416 xspi = spi_master_get_devdata(master);
417 xspi->cs_inactive = 0xffffffff;
418 xspi->bitbang.master = master;
419 xspi->bitbang.chipselect = xilinx_spi_chipselect;
420 xspi->bitbang.setup_transfer = xilinx_spi_setup_transfer;
421 xspi->bitbang.txrx_bufs = xilinx_spi_txrx_bufs;
422 init_completion(&xspi->done);
423
424 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
425 xspi->regs = devm_ioremap_resource(&pdev->dev, res);
426 if (IS_ERR(xspi->regs)) {
427 ret = PTR_ERR(xspi->regs);
428 goto put_master;
429 }
430
431 master->bus_num = pdev->id;
432 master->num_chipselect = num_cs;
433 master->dev.of_node = pdev->dev.of_node;
434
435 /*
436 * Detect endianess on the IP via loop bit in CR. Detection
437 * must be done before reset is sent because incorrect reset
438 * value generates error interrupt.
439 * Setup little endian helper functions first and try to use them
440 * and check if bit was correctly setup or not.
441 */
442 xspi->read_fn = xspi_read32;
443 xspi->write_fn = xspi_write32;
444
445 xspi->write_fn(XSPI_CR_LOOP, xspi->regs + XSPI_CR_OFFSET);
446 tmp = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
447 tmp &= XSPI_CR_LOOP;
448 if (tmp != XSPI_CR_LOOP) {
449 xspi->read_fn = xspi_read32_be;
450 xspi->write_fn = xspi_write32_be;
451 }
452
453 master->bits_per_word_mask = SPI_BPW_MASK(bits_per_word);
454 xspi->bytes_per_word = bits_per_word / 8;
455 xspi->buffer_size = xilinx_spi_find_buffer_size(xspi);
456
457 xspi->irq = platform_get_irq(pdev, 0);
458 if (xspi->irq >= 0) {
459 /* Register for SPI Interrupt */
460 ret = devm_request_irq(&pdev->dev, xspi->irq, xilinx_spi_irq, 0,
461 dev_name(&pdev->dev), xspi);
462 if (ret)
463 goto put_master;
464 }
465
466 /* SPI controller initializations */
467 xspi_init_hw(xspi);
468
469 ret = spi_bitbang_start(&xspi->bitbang);
470 if (ret) {
471 dev_err(&pdev->dev, "spi_bitbang_start FAILED\n");
472 goto put_master;
473 }
474
475 dev_info(&pdev->dev, "at 0x%08llX mapped to 0x%p, irq=%d\n",
476 (unsigned long long)res->start, xspi->regs, xspi->irq);
477
478 if (pdata) {
479 for (i = 0; i < pdata->num_devices; i++)
480 spi_new_device(master, pdata->devices + i);
481 }
482
483 platform_set_drvdata(pdev, master);
484 return 0;
485
486put_master:
487 spi_master_put(master);
488
489 return ret;
490}
491
492static int xilinx_spi_remove(struct platform_device *pdev)
493{
494 struct spi_master *master = platform_get_drvdata(pdev);
495 struct xilinx_spi *xspi = spi_master_get_devdata(master);
496 void __iomem *regs_base = xspi->regs;
497
498 spi_bitbang_stop(&xspi->bitbang);
499
500 /* Disable all the interrupts just in case */
501 xspi->write_fn(0, regs_base + XIPIF_V123B_IIER_OFFSET);
502 /* Disable the global IPIF interrupt */
503 xspi->write_fn(0, regs_base + XIPIF_V123B_DGIER_OFFSET);
504
505 spi_master_put(xspi->bitbang.master);
506
507 return 0;
508}
509
510/* work with hotplug and coldplug */
511MODULE_ALIAS("platform:" XILINX_SPI_NAME);
512
513static struct platform_driver xilinx_spi_driver = {
514 .probe = xilinx_spi_probe,
515 .remove = xilinx_spi_remove,
516 .driver = {
517 .name = XILINX_SPI_NAME,
518 .of_match_table = xilinx_spi_of_match,
519 },
520};
521module_platform_driver(xilinx_spi_driver);
522
523MODULE_AUTHOR("MontaVista Software, Inc. <source@mvista.com>");
524MODULE_DESCRIPTION("Xilinx SPI driver");
525MODULE_LICENSE("GPL");