Loading...
1/*
2 * OMAP MPUSS low power code
3 *
4 * Copyright (C) 2011 Texas Instruments, Inc.
5 * Santosh Shilimkar <santosh.shilimkar@ti.com>
6 *
7 * OMAP4430 MPUSS mainly consists of dual Cortex-A9 with per-CPU
8 * Local timer and Watchdog, GIC, SCU, PL310 L2 cache controller,
9 * CPU0 and CPU1 LPRM modules.
10 * CPU0, CPU1 and MPUSS each have there own power domain and
11 * hence multiple low power combinations of MPUSS are possible.
12 *
13 * The CPU0 and CPU1 can't support Closed switch Retention (CSWR)
14 * because the mode is not supported by hw constraints of dormant
15 * mode. While waking up from the dormant mode, a reset signal
16 * to the Cortex-A9 processor must be asserted by the external
17 * power controller.
18 *
19 * With architectural inputs and hardware recommendations, only
20 * below modes are supported from power gain vs latency point of view.
21 *
22 * CPU0 CPU1 MPUSS
23 * ----------------------------------------------
24 * ON ON ON
25 * ON(Inactive) OFF ON(Inactive)
26 * OFF OFF CSWR
27 * OFF OFF OSWR
28 * OFF OFF OFF(Device OFF *TBD)
29 * ----------------------------------------------
30 *
31 * Note: CPU0 is the master core and it is the last CPU to go down
32 * and first to wake-up when MPUSS low power states are excercised
33 *
34 *
35 * This program is free software; you can redistribute it and/or modify
36 * it under the terms of the GNU General Public License version 2 as
37 * published by the Free Software Foundation.
38 */
39
40#include <linux/kernel.h>
41#include <linux/io.h>
42#include <linux/errno.h>
43#include <linux/linkage.h>
44#include <linux/smp.h>
45
46#include <asm/cacheflush.h>
47#include <asm/tlbflush.h>
48#include <asm/smp_scu.h>
49#include <asm/pgalloc.h>
50#include <asm/suspend.h>
51#include <asm/hardware/cache-l2x0.h>
52
53#include <plat/omap44xx.h>
54
55#include "common.h"
56#include "omap4-sar-layout.h"
57#include "pm.h"
58#include "prcm_mpu44xx.h"
59#include "prminst44xx.h"
60#include "prcm44xx.h"
61#include "prm44xx.h"
62#include "prm-regbits-44xx.h"
63
64#ifdef CONFIG_SMP
65
66struct omap4_cpu_pm_info {
67 struct powerdomain *pwrdm;
68 void __iomem *scu_sar_addr;
69 void __iomem *wkup_sar_addr;
70 void __iomem *l2x0_sar_addr;
71};
72
73static DEFINE_PER_CPU(struct omap4_cpu_pm_info, omap4_pm_info);
74static struct powerdomain *mpuss_pd;
75static void __iomem *sar_base;
76
77/*
78 * Program the wakeup routine address for the CPU0 and CPU1
79 * used for OFF or DORMANT wakeup.
80 */
81static inline void set_cpu_wakeup_addr(unsigned int cpu_id, u32 addr)
82{
83 struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
84
85 __raw_writel(addr, pm_info->wkup_sar_addr);
86}
87
88/*
89 * Set the CPUx powerdomain's previous power state
90 */
91static inline void set_cpu_next_pwrst(unsigned int cpu_id,
92 unsigned int power_state)
93{
94 struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
95
96 pwrdm_set_next_pwrst(pm_info->pwrdm, power_state);
97}
98
99/*
100 * Read CPU's previous power state
101 */
102static inline unsigned int read_cpu_prev_pwrst(unsigned int cpu_id)
103{
104 struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
105
106 return pwrdm_read_prev_pwrst(pm_info->pwrdm);
107}
108
109/*
110 * Clear the CPUx powerdomain's previous power state
111 */
112static inline void clear_cpu_prev_pwrst(unsigned int cpu_id)
113{
114 struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
115
116 pwrdm_clear_all_prev_pwrst(pm_info->pwrdm);
117}
118
119/*
120 * Store the SCU power status value to scratchpad memory
121 */
122static void scu_pwrst_prepare(unsigned int cpu_id, unsigned int cpu_state)
123{
124 struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
125 u32 scu_pwr_st;
126
127 switch (cpu_state) {
128 case PWRDM_POWER_RET:
129 scu_pwr_st = SCU_PM_DORMANT;
130 break;
131 case PWRDM_POWER_OFF:
132 scu_pwr_st = SCU_PM_POWEROFF;
133 break;
134 case PWRDM_POWER_ON:
135 case PWRDM_POWER_INACTIVE:
136 default:
137 scu_pwr_st = SCU_PM_NORMAL;
138 break;
139 }
140
141 __raw_writel(scu_pwr_st, pm_info->scu_sar_addr);
142}
143
144/* Helper functions for MPUSS OSWR */
145static inline void mpuss_clear_prev_logic_pwrst(void)
146{
147 u32 reg;
148
149 reg = omap4_prminst_read_inst_reg(OMAP4430_PRM_PARTITION,
150 OMAP4430_PRM_MPU_INST, OMAP4_RM_MPU_MPU_CONTEXT_OFFSET);
151 omap4_prminst_write_inst_reg(reg, OMAP4430_PRM_PARTITION,
152 OMAP4430_PRM_MPU_INST, OMAP4_RM_MPU_MPU_CONTEXT_OFFSET);
153}
154
155static inline void cpu_clear_prev_logic_pwrst(unsigned int cpu_id)
156{
157 u32 reg;
158
159 if (cpu_id) {
160 reg = omap4_prcm_mpu_read_inst_reg(OMAP4430_PRCM_MPU_CPU1_INST,
161 OMAP4_RM_CPU1_CPU1_CONTEXT_OFFSET);
162 omap4_prcm_mpu_write_inst_reg(reg, OMAP4430_PRCM_MPU_CPU1_INST,
163 OMAP4_RM_CPU1_CPU1_CONTEXT_OFFSET);
164 } else {
165 reg = omap4_prcm_mpu_read_inst_reg(OMAP4430_PRCM_MPU_CPU0_INST,
166 OMAP4_RM_CPU0_CPU0_CONTEXT_OFFSET);
167 omap4_prcm_mpu_write_inst_reg(reg, OMAP4430_PRCM_MPU_CPU0_INST,
168 OMAP4_RM_CPU0_CPU0_CONTEXT_OFFSET);
169 }
170}
171
172/**
173 * omap4_mpuss_read_prev_context_state:
174 * Function returns the MPUSS previous context state
175 */
176u32 omap4_mpuss_read_prev_context_state(void)
177{
178 u32 reg;
179
180 reg = omap4_prminst_read_inst_reg(OMAP4430_PRM_PARTITION,
181 OMAP4430_PRM_MPU_INST, OMAP4_RM_MPU_MPU_CONTEXT_OFFSET);
182 reg &= OMAP4430_LOSTCONTEXT_DFF_MASK;
183 return reg;
184}
185
186/*
187 * Store the CPU cluster state for L2X0 low power operations.
188 */
189static void l2x0_pwrst_prepare(unsigned int cpu_id, unsigned int save_state)
190{
191 struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
192
193 __raw_writel(save_state, pm_info->l2x0_sar_addr);
194}
195
196/*
197 * Save the L2X0 AUXCTRL and POR value to SAR memory. Its used to
198 * in every restore MPUSS OFF path.
199 */
200#ifdef CONFIG_CACHE_L2X0
201static void save_l2x0_context(void)
202{
203 u32 val;
204 void __iomem *l2x0_base = omap4_get_l2cache_base();
205
206 val = __raw_readl(l2x0_base + L2X0_AUX_CTRL);
207 __raw_writel(val, sar_base + L2X0_AUXCTRL_OFFSET);
208 val = __raw_readl(l2x0_base + L2X0_PREFETCH_CTRL);
209 __raw_writel(val, sar_base + L2X0_PREFETCH_CTRL_OFFSET);
210}
211#else
212static void save_l2x0_context(void)
213{}
214#endif
215
216/**
217 * omap4_enter_lowpower: OMAP4 MPUSS Low Power Entry Function
218 * The purpose of this function is to manage low power programming
219 * of OMAP4 MPUSS subsystem
220 * @cpu : CPU ID
221 * @power_state: Low power state.
222 *
223 * MPUSS states for the context save:
224 * save_state =
225 * 0 - Nothing lost and no need to save: MPUSS INACTIVE
226 * 1 - CPUx L1 and logic lost: MPUSS CSWR
227 * 2 - CPUx L1 and logic lost + GIC lost: MPUSS OSWR
228 * 3 - CPUx L1 and logic lost + GIC + L2 lost: DEVICE OFF
229 */
230int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state)
231{
232 unsigned int save_state = 0;
233 unsigned int wakeup_cpu;
234
235 if (omap_rev() == OMAP4430_REV_ES1_0)
236 return -ENXIO;
237
238 switch (power_state) {
239 case PWRDM_POWER_ON:
240 case PWRDM_POWER_INACTIVE:
241 save_state = 0;
242 break;
243 case PWRDM_POWER_OFF:
244 save_state = 1;
245 break;
246 case PWRDM_POWER_RET:
247 default:
248 /*
249 * CPUx CSWR is invalid hardware state. Also CPUx OSWR
250 * doesn't make much scense, since logic is lost and $L1
251 * needs to be cleaned because of coherency. This makes
252 * CPUx OSWR equivalent to CPUX OFF and hence not supported
253 */
254 WARN_ON(1);
255 return -ENXIO;
256 }
257
258 pwrdm_pre_transition();
259
260 /*
261 * Check MPUSS next state and save interrupt controller if needed.
262 * In MPUSS OSWR or device OFF, interrupt controller contest is lost.
263 */
264 mpuss_clear_prev_logic_pwrst();
265 if ((pwrdm_read_next_pwrst(mpuss_pd) == PWRDM_POWER_RET) &&
266 (pwrdm_read_logic_retst(mpuss_pd) == PWRDM_POWER_OFF))
267 save_state = 2;
268
269 cpu_clear_prev_logic_pwrst(cpu);
270 set_cpu_next_pwrst(cpu, power_state);
271 set_cpu_wakeup_addr(cpu, virt_to_phys(omap4_cpu_resume));
272 scu_pwrst_prepare(cpu, power_state);
273 l2x0_pwrst_prepare(cpu, save_state);
274
275 /*
276 * Call low level function with targeted low power state.
277 */
278 cpu_suspend(save_state, omap4_finish_suspend);
279
280 /*
281 * Restore the CPUx power state to ON otherwise CPUx
282 * power domain can transitions to programmed low power
283 * state while doing WFI outside the low powe code. On
284 * secure devices, CPUx does WFI which can result in
285 * domain transition
286 */
287 wakeup_cpu = smp_processor_id();
288 set_cpu_next_pwrst(wakeup_cpu, PWRDM_POWER_ON);
289
290 pwrdm_post_transition();
291
292 return 0;
293}
294
295/**
296 * omap4_hotplug_cpu: OMAP4 CPU hotplug entry
297 * @cpu : CPU ID
298 * @power_state: CPU low power state.
299 */
300int __cpuinit omap4_hotplug_cpu(unsigned int cpu, unsigned int power_state)
301{
302 unsigned int cpu_state = 0;
303
304 if (omap_rev() == OMAP4430_REV_ES1_0)
305 return -ENXIO;
306
307 if (power_state == PWRDM_POWER_OFF)
308 cpu_state = 1;
309
310 clear_cpu_prev_pwrst(cpu);
311 set_cpu_next_pwrst(cpu, power_state);
312 set_cpu_wakeup_addr(cpu, virt_to_phys(omap_secondary_startup));
313 scu_pwrst_prepare(cpu, power_state);
314
315 /*
316 * CPU never retuns back if targetted power state is OFF mode.
317 * CPU ONLINE follows normal CPU ONLINE ptah via
318 * omap_secondary_startup().
319 */
320 omap4_finish_suspend(cpu_state);
321
322 set_cpu_next_pwrst(cpu, PWRDM_POWER_ON);
323 return 0;
324}
325
326
327/*
328 * Initialise OMAP4 MPUSS
329 */
330int __init omap4_mpuss_init(void)
331{
332 struct omap4_cpu_pm_info *pm_info;
333
334 if (omap_rev() == OMAP4430_REV_ES1_0) {
335 WARN(1, "Power Management not supported on OMAP4430 ES1.0\n");
336 return -ENODEV;
337 }
338
339 sar_base = omap4_get_sar_ram_base();
340
341 /* Initilaise per CPU PM information */
342 pm_info = &per_cpu(omap4_pm_info, 0x0);
343 pm_info->scu_sar_addr = sar_base + SCU_OFFSET0;
344 pm_info->wkup_sar_addr = sar_base + CPU0_WAKEUP_NS_PA_ADDR_OFFSET;
345 pm_info->l2x0_sar_addr = sar_base + L2X0_SAVE_OFFSET0;
346 pm_info->pwrdm = pwrdm_lookup("cpu0_pwrdm");
347 if (!pm_info->pwrdm) {
348 pr_err("Lookup failed for CPU0 pwrdm\n");
349 return -ENODEV;
350 }
351
352 /* Clear CPU previous power domain state */
353 pwrdm_clear_all_prev_pwrst(pm_info->pwrdm);
354 cpu_clear_prev_logic_pwrst(0);
355
356 /* Initialise CPU0 power domain state to ON */
357 pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON);
358
359 pm_info = &per_cpu(omap4_pm_info, 0x1);
360 pm_info->scu_sar_addr = sar_base + SCU_OFFSET1;
361 pm_info->wkup_sar_addr = sar_base + CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
362 pm_info->l2x0_sar_addr = sar_base + L2X0_SAVE_OFFSET1;
363 pm_info->pwrdm = pwrdm_lookup("cpu1_pwrdm");
364 if (!pm_info->pwrdm) {
365 pr_err("Lookup failed for CPU1 pwrdm\n");
366 return -ENODEV;
367 }
368
369 /* Clear CPU previous power domain state */
370 pwrdm_clear_all_prev_pwrst(pm_info->pwrdm);
371 cpu_clear_prev_logic_pwrst(1);
372
373 /* Initialise CPU1 power domain state to ON */
374 pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON);
375
376 mpuss_pd = pwrdm_lookup("mpu_pwrdm");
377 if (!mpuss_pd) {
378 pr_err("Failed to lookup MPUSS power domain\n");
379 return -ENODEV;
380 }
381 pwrdm_clear_all_prev_pwrst(mpuss_pd);
382 mpuss_clear_prev_logic_pwrst();
383
384 /* Save device type on scratchpad for low level code to use */
385 if (omap_type() != OMAP2_DEVICE_TYPE_GP)
386 __raw_writel(1, sar_base + OMAP_TYPE_OFFSET);
387 else
388 __raw_writel(0, sar_base + OMAP_TYPE_OFFSET);
389
390 save_l2x0_context();
391
392 return 0;
393}
394
395#endif
1/*
2 * OMAP MPUSS low power code
3 *
4 * Copyright (C) 2011 Texas Instruments, Inc.
5 * Santosh Shilimkar <santosh.shilimkar@ti.com>
6 *
7 * OMAP4430 MPUSS mainly consists of dual Cortex-A9 with per-CPU
8 * Local timer and Watchdog, GIC, SCU, PL310 L2 cache controller,
9 * CPU0 and CPU1 LPRM modules.
10 * CPU0, CPU1 and MPUSS each have there own power domain and
11 * hence multiple low power combinations of MPUSS are possible.
12 *
13 * The CPU0 and CPU1 can't support Closed switch Retention (CSWR)
14 * because the mode is not supported by hw constraints of dormant
15 * mode. While waking up from the dormant mode, a reset signal
16 * to the Cortex-A9 processor must be asserted by the external
17 * power controller.
18 *
19 * With architectural inputs and hardware recommendations, only
20 * below modes are supported from power gain vs latency point of view.
21 *
22 * CPU0 CPU1 MPUSS
23 * ----------------------------------------------
24 * ON ON ON
25 * ON(Inactive) OFF ON(Inactive)
26 * OFF OFF CSWR
27 * OFF OFF OSWR
28 * OFF OFF OFF(Device OFF *TBD)
29 * ----------------------------------------------
30 *
31 * Note: CPU0 is the master core and it is the last CPU to go down
32 * and first to wake-up when MPUSS low power states are excercised
33 *
34 *
35 * This program is free software; you can redistribute it and/or modify
36 * it under the terms of the GNU General Public License version 2 as
37 * published by the Free Software Foundation.
38 */
39
40#include <linux/kernel.h>
41#include <linux/io.h>
42#include <linux/errno.h>
43#include <linux/linkage.h>
44#include <linux/smp.h>
45
46#include <asm/cacheflush.h>
47#include <asm/tlbflush.h>
48#include <asm/smp_scu.h>
49#include <asm/pgalloc.h>
50#include <asm/suspend.h>
51#include <asm/virt.h>
52#include <asm/hardware/cache-l2x0.h>
53
54#include "soc.h"
55#include "common.h"
56#include "omap44xx.h"
57#include "omap4-sar-layout.h"
58#include "pm.h"
59#include "prcm_mpu44xx.h"
60#include "prcm_mpu54xx.h"
61#include "prminst44xx.h"
62#include "prcm44xx.h"
63#include "prm44xx.h"
64#include "prm-regbits-44xx.h"
65
66static void __iomem *sar_base;
67static u32 old_cpu1_ns_pa_addr;
68
69#if defined(CONFIG_PM) && defined(CONFIG_SMP)
70
71struct omap4_cpu_pm_info {
72 struct powerdomain *pwrdm;
73 void __iomem *scu_sar_addr;
74 void __iomem *wkup_sar_addr;
75 void __iomem *l2x0_sar_addr;
76};
77
78/**
79 * struct cpu_pm_ops - CPU pm operations
80 * @finish_suspend: CPU suspend finisher function pointer
81 * @resume: CPU resume function pointer
82 * @scu_prepare: CPU Snoop Control program function pointer
83 * @hotplug_restart: CPU restart function pointer
84 *
85 * Structure holds functions pointer for CPU low power operations like
86 * suspend, resume and scu programming.
87 */
88struct cpu_pm_ops {
89 int (*finish_suspend)(unsigned long cpu_state);
90 void (*resume)(void);
91 void (*scu_prepare)(unsigned int cpu_id, unsigned int cpu_state);
92 void (*hotplug_restart)(void);
93};
94
95static DEFINE_PER_CPU(struct omap4_cpu_pm_info, omap4_pm_info);
96static struct powerdomain *mpuss_pd;
97static u32 cpu_context_offset;
98
99static int default_finish_suspend(unsigned long cpu_state)
100{
101 omap_do_wfi();
102 return 0;
103}
104
105static void dummy_cpu_resume(void)
106{}
107
108static void dummy_scu_prepare(unsigned int cpu_id, unsigned int cpu_state)
109{}
110
111static struct cpu_pm_ops omap_pm_ops = {
112 .finish_suspend = default_finish_suspend,
113 .resume = dummy_cpu_resume,
114 .scu_prepare = dummy_scu_prepare,
115 .hotplug_restart = dummy_cpu_resume,
116};
117
118/*
119 * Program the wakeup routine address for the CPU0 and CPU1
120 * used for OFF or DORMANT wakeup.
121 */
122static inline void set_cpu_wakeup_addr(unsigned int cpu_id, u32 addr)
123{
124 struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
125
126 if (pm_info->wkup_sar_addr)
127 writel_relaxed(addr, pm_info->wkup_sar_addr);
128}
129
130/*
131 * Store the SCU power status value to scratchpad memory
132 */
133static void scu_pwrst_prepare(unsigned int cpu_id, unsigned int cpu_state)
134{
135 struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
136 u32 scu_pwr_st;
137
138 switch (cpu_state) {
139 case PWRDM_POWER_RET:
140 scu_pwr_st = SCU_PM_DORMANT;
141 break;
142 case PWRDM_POWER_OFF:
143 scu_pwr_st = SCU_PM_POWEROFF;
144 break;
145 case PWRDM_POWER_ON:
146 case PWRDM_POWER_INACTIVE:
147 default:
148 scu_pwr_st = SCU_PM_NORMAL;
149 break;
150 }
151
152 if (pm_info->scu_sar_addr)
153 writel_relaxed(scu_pwr_st, pm_info->scu_sar_addr);
154}
155
156/* Helper functions for MPUSS OSWR */
157static inline void mpuss_clear_prev_logic_pwrst(void)
158{
159 u32 reg;
160
161 reg = omap4_prminst_read_inst_reg(OMAP4430_PRM_PARTITION,
162 OMAP4430_PRM_MPU_INST, OMAP4_RM_MPU_MPU_CONTEXT_OFFSET);
163 omap4_prminst_write_inst_reg(reg, OMAP4430_PRM_PARTITION,
164 OMAP4430_PRM_MPU_INST, OMAP4_RM_MPU_MPU_CONTEXT_OFFSET);
165}
166
167static inline void cpu_clear_prev_logic_pwrst(unsigned int cpu_id)
168{
169 u32 reg;
170
171 if (cpu_id) {
172 reg = omap4_prcm_mpu_read_inst_reg(OMAP4430_PRCM_MPU_CPU1_INST,
173 cpu_context_offset);
174 omap4_prcm_mpu_write_inst_reg(reg, OMAP4430_PRCM_MPU_CPU1_INST,
175 cpu_context_offset);
176 } else {
177 reg = omap4_prcm_mpu_read_inst_reg(OMAP4430_PRCM_MPU_CPU0_INST,
178 cpu_context_offset);
179 omap4_prcm_mpu_write_inst_reg(reg, OMAP4430_PRCM_MPU_CPU0_INST,
180 cpu_context_offset);
181 }
182}
183
184/*
185 * Store the CPU cluster state for L2X0 low power operations.
186 */
187static void l2x0_pwrst_prepare(unsigned int cpu_id, unsigned int save_state)
188{
189 struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu_id);
190
191 if (pm_info->l2x0_sar_addr)
192 writel_relaxed(save_state, pm_info->l2x0_sar_addr);
193}
194
195/*
196 * Save the L2X0 AUXCTRL and POR value to SAR memory. Its used to
197 * in every restore MPUSS OFF path.
198 */
199#ifdef CONFIG_CACHE_L2X0
200static void __init save_l2x0_context(void)
201{
202 void __iomem *l2x0_base = omap4_get_l2cache_base();
203
204 if (l2x0_base && sar_base) {
205 writel_relaxed(l2x0_saved_regs.aux_ctrl,
206 sar_base + L2X0_AUXCTRL_OFFSET);
207 writel_relaxed(l2x0_saved_regs.prefetch_ctrl,
208 sar_base + L2X0_PREFETCH_CTRL_OFFSET);
209 }
210}
211#else
212static void __init save_l2x0_context(void)
213{}
214#endif
215
216/**
217 * omap4_enter_lowpower: OMAP4 MPUSS Low Power Entry Function
218 * The purpose of this function is to manage low power programming
219 * of OMAP4 MPUSS subsystem
220 * @cpu : CPU ID
221 * @power_state: Low power state.
222 *
223 * MPUSS states for the context save:
224 * save_state =
225 * 0 - Nothing lost and no need to save: MPUSS INACTIVE
226 * 1 - CPUx L1 and logic lost: MPUSS CSWR
227 * 2 - CPUx L1 and logic lost + GIC lost: MPUSS OSWR
228 * 3 - CPUx L1 and logic lost + GIC + L2 lost: DEVICE OFF
229 */
230int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state)
231{
232 struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu);
233 unsigned int save_state = 0, cpu_logic_state = PWRDM_POWER_RET;
234 unsigned int wakeup_cpu;
235
236 if (omap_rev() == OMAP4430_REV_ES1_0)
237 return -ENXIO;
238
239 switch (power_state) {
240 case PWRDM_POWER_ON:
241 case PWRDM_POWER_INACTIVE:
242 save_state = 0;
243 break;
244 case PWRDM_POWER_OFF:
245 cpu_logic_state = PWRDM_POWER_OFF;
246 save_state = 1;
247 break;
248 case PWRDM_POWER_RET:
249 if (IS_PM44XX_ERRATUM(PM_OMAP4_CPU_OSWR_DISABLE))
250 save_state = 0;
251 break;
252 default:
253 /*
254 * CPUx CSWR is invalid hardware state. Also CPUx OSWR
255 * doesn't make much scense, since logic is lost and $L1
256 * needs to be cleaned because of coherency. This makes
257 * CPUx OSWR equivalent to CPUX OFF and hence not supported
258 */
259 WARN_ON(1);
260 return -ENXIO;
261 }
262
263 pwrdm_pre_transition(NULL);
264
265 /*
266 * Check MPUSS next state and save interrupt controller if needed.
267 * In MPUSS OSWR or device OFF, interrupt controller contest is lost.
268 */
269 mpuss_clear_prev_logic_pwrst();
270 if ((pwrdm_read_next_pwrst(mpuss_pd) == PWRDM_POWER_RET) &&
271 (pwrdm_read_logic_retst(mpuss_pd) == PWRDM_POWER_OFF))
272 save_state = 2;
273
274 cpu_clear_prev_logic_pwrst(cpu);
275 pwrdm_set_next_pwrst(pm_info->pwrdm, power_state);
276 pwrdm_set_logic_retst(pm_info->pwrdm, cpu_logic_state);
277 set_cpu_wakeup_addr(cpu, __pa_symbol(omap_pm_ops.resume));
278 omap_pm_ops.scu_prepare(cpu, power_state);
279 l2x0_pwrst_prepare(cpu, save_state);
280
281 /*
282 * Call low level function with targeted low power state.
283 */
284 if (save_state)
285 cpu_suspend(save_state, omap_pm_ops.finish_suspend);
286 else
287 omap_pm_ops.finish_suspend(save_state);
288
289 if (IS_PM44XX_ERRATUM(PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD) && cpu)
290 gic_dist_enable();
291
292 /*
293 * Restore the CPUx power state to ON otherwise CPUx
294 * power domain can transitions to programmed low power
295 * state while doing WFI outside the low powe code. On
296 * secure devices, CPUx does WFI which can result in
297 * domain transition
298 */
299 wakeup_cpu = smp_processor_id();
300 pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON);
301
302 pwrdm_post_transition(NULL);
303
304 return 0;
305}
306
307/**
308 * omap4_hotplug_cpu: OMAP4 CPU hotplug entry
309 * @cpu : CPU ID
310 * @power_state: CPU low power state.
311 */
312int omap4_hotplug_cpu(unsigned int cpu, unsigned int power_state)
313{
314 struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu);
315 unsigned int cpu_state = 0;
316
317 if (omap_rev() == OMAP4430_REV_ES1_0)
318 return -ENXIO;
319
320 /* Use the achievable power state for the domain */
321 power_state = pwrdm_get_valid_lp_state(pm_info->pwrdm,
322 false, power_state);
323
324 if (power_state == PWRDM_POWER_OFF)
325 cpu_state = 1;
326
327 pwrdm_clear_all_prev_pwrst(pm_info->pwrdm);
328 pwrdm_set_next_pwrst(pm_info->pwrdm, power_state);
329 set_cpu_wakeup_addr(cpu, __pa_symbol(omap_pm_ops.hotplug_restart));
330 omap_pm_ops.scu_prepare(cpu, power_state);
331
332 /*
333 * CPU never retuns back if targeted power state is OFF mode.
334 * CPU ONLINE follows normal CPU ONLINE ptah via
335 * omap4_secondary_startup().
336 */
337 omap_pm_ops.finish_suspend(cpu_state);
338
339 pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON);
340 return 0;
341}
342
343
344/*
345 * Enable Mercury Fast HG retention mode by default.
346 */
347static void enable_mercury_retention_mode(void)
348{
349 u32 reg;
350
351 reg = omap4_prcm_mpu_read_inst_reg(OMAP54XX_PRCM_MPU_DEVICE_INST,
352 OMAP54XX_PRCM_MPU_PRM_PSCON_COUNT_OFFSET);
353 /* Enable HG_EN, HG_RAMPUP = fast mode */
354 reg |= BIT(24) | BIT(25);
355 omap4_prcm_mpu_write_inst_reg(reg, OMAP54XX_PRCM_MPU_DEVICE_INST,
356 OMAP54XX_PRCM_MPU_PRM_PSCON_COUNT_OFFSET);
357}
358
359/*
360 * Initialise OMAP4 MPUSS
361 */
362int __init omap4_mpuss_init(void)
363{
364 struct omap4_cpu_pm_info *pm_info;
365
366 if (omap_rev() == OMAP4430_REV_ES1_0) {
367 WARN(1, "Power Management not supported on OMAP4430 ES1.0\n");
368 return -ENODEV;
369 }
370
371 /* Initilaise per CPU PM information */
372 pm_info = &per_cpu(omap4_pm_info, 0x0);
373 if (sar_base) {
374 pm_info->scu_sar_addr = sar_base + SCU_OFFSET0;
375 if (cpu_is_omap44xx())
376 pm_info->wkup_sar_addr = sar_base +
377 CPU0_WAKEUP_NS_PA_ADDR_OFFSET;
378 else
379 pm_info->wkup_sar_addr = sar_base +
380 OMAP5_CPU0_WAKEUP_NS_PA_ADDR_OFFSET;
381 pm_info->l2x0_sar_addr = sar_base + L2X0_SAVE_OFFSET0;
382 }
383 pm_info->pwrdm = pwrdm_lookup("cpu0_pwrdm");
384 if (!pm_info->pwrdm) {
385 pr_err("Lookup failed for CPU0 pwrdm\n");
386 return -ENODEV;
387 }
388
389 /* Clear CPU previous power domain state */
390 pwrdm_clear_all_prev_pwrst(pm_info->pwrdm);
391 cpu_clear_prev_logic_pwrst(0);
392
393 /* Initialise CPU0 power domain state to ON */
394 pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON);
395
396 pm_info = &per_cpu(omap4_pm_info, 0x1);
397 if (sar_base) {
398 pm_info->scu_sar_addr = sar_base + SCU_OFFSET1;
399 if (cpu_is_omap44xx())
400 pm_info->wkup_sar_addr = sar_base +
401 CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
402 else
403 pm_info->wkup_sar_addr = sar_base +
404 OMAP5_CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
405 pm_info->l2x0_sar_addr = sar_base + L2X0_SAVE_OFFSET1;
406 }
407
408 pm_info->pwrdm = pwrdm_lookup("cpu1_pwrdm");
409 if (!pm_info->pwrdm) {
410 pr_err("Lookup failed for CPU1 pwrdm\n");
411 return -ENODEV;
412 }
413
414 /* Clear CPU previous power domain state */
415 pwrdm_clear_all_prev_pwrst(pm_info->pwrdm);
416 cpu_clear_prev_logic_pwrst(1);
417
418 /* Initialise CPU1 power domain state to ON */
419 pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON);
420
421 mpuss_pd = pwrdm_lookup("mpu_pwrdm");
422 if (!mpuss_pd) {
423 pr_err("Failed to lookup MPUSS power domain\n");
424 return -ENODEV;
425 }
426 pwrdm_clear_all_prev_pwrst(mpuss_pd);
427 mpuss_clear_prev_logic_pwrst();
428
429 if (sar_base) {
430 /* Save device type on scratchpad for low level code to use */
431 writel_relaxed((omap_type() != OMAP2_DEVICE_TYPE_GP) ? 1 : 0,
432 sar_base + OMAP_TYPE_OFFSET);
433 save_l2x0_context();
434 }
435
436 if (cpu_is_omap44xx()) {
437 omap_pm_ops.finish_suspend = omap4_finish_suspend;
438 omap_pm_ops.resume = omap4_cpu_resume;
439 omap_pm_ops.scu_prepare = scu_pwrst_prepare;
440 omap_pm_ops.hotplug_restart = omap4_secondary_startup;
441 cpu_context_offset = OMAP4_RM_CPU0_CPU0_CONTEXT_OFFSET;
442 } else if (soc_is_omap54xx() || soc_is_dra7xx()) {
443 cpu_context_offset = OMAP54XX_RM_CPU0_CPU0_CONTEXT_OFFSET;
444 enable_mercury_retention_mode();
445 }
446
447 if (cpu_is_omap446x())
448 omap_pm_ops.hotplug_restart = omap4460_secondary_startup;
449
450 return 0;
451}
452
453#endif
454
455u32 omap4_get_cpu1_ns_pa_addr(void)
456{
457 return old_cpu1_ns_pa_addr;
458}
459
460/*
461 * For kexec, we must set CPU1_WAKEUP_NS_PA_ADDR to point to
462 * current kernel's secondary_startup() early before
463 * clockdomains_init(). Otherwise clockdomain_init() can
464 * wake CPU1 and cause a hang.
465 */
466void __init omap4_mpuss_early_init(void)
467{
468 unsigned long startup_pa;
469 void __iomem *ns_pa_addr;
470
471 if (!(soc_is_omap44xx() || soc_is_omap54xx()))
472 return;
473
474 sar_base = omap4_get_sar_ram_base();
475
476 /* Save old NS_PA_ADDR for validity checks later on */
477 if (soc_is_omap44xx())
478 ns_pa_addr = sar_base + CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
479 else
480 ns_pa_addr = sar_base + OMAP5_CPU1_WAKEUP_NS_PA_ADDR_OFFSET;
481 old_cpu1_ns_pa_addr = readl_relaxed(ns_pa_addr);
482
483 if (soc_is_omap443x())
484 startup_pa = __pa_symbol(omap4_secondary_startup);
485 else if (soc_is_omap446x())
486 startup_pa = __pa_symbol(omap4460_secondary_startup);
487 else if ((__boot_cpu_mode & MODE_MASK) == HYP_MODE)
488 startup_pa = __pa_symbol(omap5_secondary_hyp_startup);
489 else
490 startup_pa = __pa_symbol(omap5_secondary_startup);
491
492 if (soc_is_omap44xx())
493 writel_relaxed(startup_pa, sar_base +
494 CPU1_WAKEUP_NS_PA_ADDR_OFFSET);
495 else
496 writel_relaxed(startup_pa, sar_base +
497 OMAP5_CPU1_WAKEUP_NS_PA_ADDR_OFFSET);
498}