Loading...
1/*
2 * arch/arm/mach-ixp4xx/ixdp425-setup.c
3 *
4 * IXDP425/IXCDP1100 board-setup
5 *
6 * Copyright (C) 2003-2005 MontaVista Software, Inc.
7 *
8 * Author: Deepak Saxena <dsaxena@plexity.net>
9 */
10
11#include <linux/kernel.h>
12#include <linux/init.h>
13#include <linux/device.h>
14#include <linux/serial.h>
15#include <linux/tty.h>
16#include <linux/serial_8250.h>
17#include <linux/i2c-gpio.h>
18#include <linux/io.h>
19#include <linux/mtd/mtd.h>
20#include <linux/mtd/nand.h>
21#include <linux/mtd/partitions.h>
22#include <linux/delay.h>
23#include <asm/types.h>
24#include <asm/setup.h>
25#include <asm/memory.h>
26#include <mach/hardware.h>
27#include <asm/mach-types.h>
28#include <asm/irq.h>
29#include <asm/mach/arch.h>
30#include <asm/mach/flash.h>
31
32#define IXDP425_SDA_PIN 7
33#define IXDP425_SCL_PIN 6
34
35/* NAND Flash pins */
36#define IXDP425_NAND_NCE_PIN 12
37
38#define IXDP425_NAND_CMD_BYTE 0x01
39#define IXDP425_NAND_ADDR_BYTE 0x02
40
41static struct flash_platform_data ixdp425_flash_data = {
42 .map_name = "cfi_probe",
43 .width = 2,
44};
45
46static struct resource ixdp425_flash_resource = {
47 .flags = IORESOURCE_MEM,
48};
49
50static struct platform_device ixdp425_flash = {
51 .name = "IXP4XX-Flash",
52 .id = 0,
53 .dev = {
54 .platform_data = &ixdp425_flash_data,
55 },
56 .num_resources = 1,
57 .resource = &ixdp425_flash_resource,
58};
59
60#if defined(CONFIG_MTD_NAND_PLATFORM) || \
61 defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
62
63static struct mtd_partition ixdp425_partitions[] = {
64 {
65 .name = "ixp400 NAND FS 0",
66 .offset = 0,
67 .size = SZ_8M
68 }, {
69 .name = "ixp400 NAND FS 1",
70 .offset = MTDPART_OFS_APPEND,
71 .size = MTDPART_SIZ_FULL
72 },
73};
74
75static void
76ixdp425_flash_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
77{
78 struct nand_chip *this = mtd->priv;
79 int offset = (int)this->priv;
80
81 if (ctrl & NAND_CTRL_CHANGE) {
82 if (ctrl & NAND_NCE) {
83 gpio_line_set(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_LOW);
84 udelay(5);
85 } else
86 gpio_line_set(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_HIGH);
87
88 offset = (ctrl & NAND_CLE) ? IXDP425_NAND_CMD_BYTE : 0;
89 offset |= (ctrl & NAND_ALE) ? IXDP425_NAND_ADDR_BYTE : 0;
90 this->priv = (void *)offset;
91 }
92
93 if (cmd != NAND_CMD_NONE)
94 writeb(cmd, this->IO_ADDR_W + offset);
95}
96
97static struct platform_nand_data ixdp425_flash_nand_data = {
98 .chip = {
99 .nr_chips = 1,
100 .chip_delay = 30,
101 .partitions = ixdp425_partitions,
102 .nr_partitions = ARRAY_SIZE(ixdp425_partitions),
103 },
104 .ctrl = {
105 .cmd_ctrl = ixdp425_flash_nand_cmd_ctrl
106 }
107};
108
109static struct resource ixdp425_flash_nand_resource = {
110 .flags = IORESOURCE_MEM,
111};
112
113static struct platform_device ixdp425_flash_nand = {
114 .name = "gen_nand",
115 .id = -1,
116 .dev = {
117 .platform_data = &ixdp425_flash_nand_data,
118 },
119 .num_resources = 1,
120 .resource = &ixdp425_flash_nand_resource,
121};
122#endif /* CONFIG_MTD_NAND_PLATFORM */
123
124static struct i2c_gpio_platform_data ixdp425_i2c_gpio_data = {
125 .sda_pin = IXDP425_SDA_PIN,
126 .scl_pin = IXDP425_SCL_PIN,
127};
128
129static struct platform_device ixdp425_i2c_gpio = {
130 .name = "i2c-gpio",
131 .id = 0,
132 .dev = {
133 .platform_data = &ixdp425_i2c_gpio_data,
134 },
135};
136
137static struct resource ixdp425_uart_resources[] = {
138 {
139 .start = IXP4XX_UART1_BASE_PHYS,
140 .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
141 .flags = IORESOURCE_MEM
142 },
143 {
144 .start = IXP4XX_UART2_BASE_PHYS,
145 .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
146 .flags = IORESOURCE_MEM
147 }
148};
149
150static struct plat_serial8250_port ixdp425_uart_data[] = {
151 {
152 .mapbase = IXP4XX_UART1_BASE_PHYS,
153 .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
154 .irq = IRQ_IXP4XX_UART1,
155 .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
156 .iotype = UPIO_MEM,
157 .regshift = 2,
158 .uartclk = IXP4XX_UART_XTAL,
159 },
160 {
161 .mapbase = IXP4XX_UART2_BASE_PHYS,
162 .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
163 .irq = IRQ_IXP4XX_UART2,
164 .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
165 .iotype = UPIO_MEM,
166 .regshift = 2,
167 .uartclk = IXP4XX_UART_XTAL,
168 },
169 { },
170};
171
172static struct platform_device ixdp425_uart = {
173 .name = "serial8250",
174 .id = PLAT8250_DEV_PLATFORM,
175 .dev.platform_data = ixdp425_uart_data,
176 .num_resources = 2,
177 .resource = ixdp425_uart_resources
178};
179
180/* Built-in 10/100 Ethernet MAC interfaces */
181static struct eth_plat_info ixdp425_plat_eth[] = {
182 {
183 .phy = 0,
184 .rxq = 3,
185 .txreadyq = 20,
186 }, {
187 .phy = 1,
188 .rxq = 4,
189 .txreadyq = 21,
190 }
191};
192
193static struct platform_device ixdp425_eth[] = {
194 {
195 .name = "ixp4xx_eth",
196 .id = IXP4XX_ETH_NPEB,
197 .dev.platform_data = ixdp425_plat_eth,
198 }, {
199 .name = "ixp4xx_eth",
200 .id = IXP4XX_ETH_NPEC,
201 .dev.platform_data = ixdp425_plat_eth + 1,
202 }
203};
204
205static struct platform_device *ixdp425_devices[] __initdata = {
206 &ixdp425_i2c_gpio,
207 &ixdp425_flash,
208#if defined(CONFIG_MTD_NAND_PLATFORM) || \
209 defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
210 &ixdp425_flash_nand,
211#endif
212 &ixdp425_uart,
213 &ixdp425_eth[0],
214 &ixdp425_eth[1],
215};
216
217static void __init ixdp425_init(void)
218{
219 ixp4xx_sys_init();
220
221 ixdp425_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
222 ixdp425_flash_resource.end =
223 IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
224
225#if defined(CONFIG_MTD_NAND_PLATFORM) || \
226 defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
227 ixdp425_flash_nand_resource.start = IXP4XX_EXP_BUS_BASE(3),
228 ixdp425_flash_nand_resource.end = IXP4XX_EXP_BUS_BASE(3) + 0x10 - 1;
229
230 gpio_line_config(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_OUT);
231
232 /* Configure expansion bus for NAND Flash */
233 *IXP4XX_EXP_CS3 = IXP4XX_EXP_BUS_CS_EN |
234 IXP4XX_EXP_BUS_STROBE_T(1) | /* extend by 1 clock */
235 IXP4XX_EXP_BUS_CYCLES(0) | /* Intel cycles */
236 IXP4XX_EXP_BUS_SIZE(0) | /* 512bytes addr space*/
237 IXP4XX_EXP_BUS_WR_EN |
238 IXP4XX_EXP_BUS_BYTE_EN; /* 8 bit data bus */
239#endif
240
241 if (cpu_is_ixp43x()) {
242 ixdp425_uart.num_resources = 1;
243 ixdp425_uart_data[1].flags = 0;
244 }
245
246 platform_add_devices(ixdp425_devices, ARRAY_SIZE(ixdp425_devices));
247}
248
249#ifdef CONFIG_ARCH_IXDP425
250MACHINE_START(IXDP425, "Intel IXDP425 Development Platform")
251 /* Maintainer: MontaVista Software, Inc. */
252 .map_io = ixp4xx_map_io,
253 .init_early = ixp4xx_init_early,
254 .init_irq = ixp4xx_init_irq,
255 .timer = &ixp4xx_timer,
256 .atag_offset = 0x100,
257 .init_machine = ixdp425_init,
258#if defined(CONFIG_PCI)
259 .dma_zone_size = SZ_64M,
260#endif
261 .restart = ixp4xx_restart,
262MACHINE_END
263#endif
264
265#ifdef CONFIG_MACH_IXDP465
266MACHINE_START(IXDP465, "Intel IXDP465 Development Platform")
267 /* Maintainer: MontaVista Software, Inc. */
268 .map_io = ixp4xx_map_io,
269 .init_early = ixp4xx_init_early,
270 .init_irq = ixp4xx_init_irq,
271 .timer = &ixp4xx_timer,
272 .atag_offset = 0x100,
273 .init_machine = ixdp425_init,
274#if defined(CONFIG_PCI)
275 .dma_zone_size = SZ_64M,
276#endif
277MACHINE_END
278#endif
279
280#ifdef CONFIG_ARCH_PRPMC1100
281MACHINE_START(IXCDP1100, "Intel IXCDP1100 Development Platform")
282 /* Maintainer: MontaVista Software, Inc. */
283 .map_io = ixp4xx_map_io,
284 .init_early = ixp4xx_init_early,
285 .init_irq = ixp4xx_init_irq,
286 .timer = &ixp4xx_timer,
287 .atag_offset = 0x100,
288 .init_machine = ixdp425_init,
289#if defined(CONFIG_PCI)
290 .dma_zone_size = SZ_64M,
291#endif
292MACHINE_END
293#endif
294
295#ifdef CONFIG_MACH_KIXRP435
296MACHINE_START(KIXRP435, "Intel KIXRP435 Reference Platform")
297 /* Maintainer: MontaVista Software, Inc. */
298 .map_io = ixp4xx_map_io,
299 .init_early = ixp4xx_init_early,
300 .init_irq = ixp4xx_init_irq,
301 .timer = &ixp4xx_timer,
302 .atag_offset = 0x100,
303 .init_machine = ixdp425_init,
304#if defined(CONFIG_PCI)
305 .dma_zone_size = SZ_64M,
306#endif
307MACHINE_END
308#endif
1/*
2 * arch/arm/mach-ixp4xx/ixdp425-setup.c
3 *
4 * IXDP425/IXCDP1100 board-setup
5 *
6 * Copyright (C) 2003-2005 MontaVista Software, Inc.
7 *
8 * Author: Deepak Saxena <dsaxena@plexity.net>
9 */
10
11#include <linux/kernel.h>
12#include <linux/init.h>
13#include <linux/device.h>
14#include <linux/serial.h>
15#include <linux/tty.h>
16#include <linux/serial_8250.h>
17#include <linux/i2c-gpio.h>
18#include <linux/io.h>
19#include <linux/mtd/mtd.h>
20#include <linux/mtd/nand.h>
21#include <linux/mtd/partitions.h>
22#include <linux/delay.h>
23#include <linux/gpio.h>
24#include <asm/types.h>
25#include <asm/setup.h>
26#include <asm/memory.h>
27#include <mach/hardware.h>
28#include <asm/mach-types.h>
29#include <asm/irq.h>
30#include <asm/mach/arch.h>
31#include <asm/mach/flash.h>
32
33#define IXDP425_SDA_PIN 7
34#define IXDP425_SCL_PIN 6
35
36/* NAND Flash pins */
37#define IXDP425_NAND_NCE_PIN 12
38
39#define IXDP425_NAND_CMD_BYTE 0x01
40#define IXDP425_NAND_ADDR_BYTE 0x02
41
42static struct flash_platform_data ixdp425_flash_data = {
43 .map_name = "cfi_probe",
44 .width = 2,
45};
46
47static struct resource ixdp425_flash_resource = {
48 .flags = IORESOURCE_MEM,
49};
50
51static struct platform_device ixdp425_flash = {
52 .name = "IXP4XX-Flash",
53 .id = 0,
54 .dev = {
55 .platform_data = &ixdp425_flash_data,
56 },
57 .num_resources = 1,
58 .resource = &ixdp425_flash_resource,
59};
60
61#if defined(CONFIG_MTD_NAND_PLATFORM) || \
62 defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
63
64static struct mtd_partition ixdp425_partitions[] = {
65 {
66 .name = "ixp400 NAND FS 0",
67 .offset = 0,
68 .size = SZ_8M
69 }, {
70 .name = "ixp400 NAND FS 1",
71 .offset = MTDPART_OFS_APPEND,
72 .size = MTDPART_SIZ_FULL
73 },
74};
75
76static void
77ixdp425_flash_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
78{
79 struct nand_chip *this = mtd_to_nand(mtd);
80 int offset = (int)nand_get_controller_data(this);
81
82 if (ctrl & NAND_CTRL_CHANGE) {
83 if (ctrl & NAND_NCE) {
84 gpio_set_value(IXDP425_NAND_NCE_PIN, 0);
85 udelay(5);
86 } else
87 gpio_set_value(IXDP425_NAND_NCE_PIN, 1);
88
89 offset = (ctrl & NAND_CLE) ? IXDP425_NAND_CMD_BYTE : 0;
90 offset |= (ctrl & NAND_ALE) ? IXDP425_NAND_ADDR_BYTE : 0;
91 nand_set_controller_data(this, (void *)offset);
92 }
93
94 if (cmd != NAND_CMD_NONE)
95 writeb(cmd, this->IO_ADDR_W + offset);
96}
97
98static struct platform_nand_data ixdp425_flash_nand_data = {
99 .chip = {
100 .nr_chips = 1,
101 .chip_delay = 30,
102 .partitions = ixdp425_partitions,
103 .nr_partitions = ARRAY_SIZE(ixdp425_partitions),
104 },
105 .ctrl = {
106 .cmd_ctrl = ixdp425_flash_nand_cmd_ctrl
107 }
108};
109
110static struct resource ixdp425_flash_nand_resource = {
111 .flags = IORESOURCE_MEM,
112};
113
114static struct platform_device ixdp425_flash_nand = {
115 .name = "gen_nand",
116 .id = -1,
117 .dev = {
118 .platform_data = &ixdp425_flash_nand_data,
119 },
120 .num_resources = 1,
121 .resource = &ixdp425_flash_nand_resource,
122};
123#endif /* CONFIG_MTD_NAND_PLATFORM */
124
125static struct i2c_gpio_platform_data ixdp425_i2c_gpio_data = {
126 .sda_pin = IXDP425_SDA_PIN,
127 .scl_pin = IXDP425_SCL_PIN,
128};
129
130static struct platform_device ixdp425_i2c_gpio = {
131 .name = "i2c-gpio",
132 .id = 0,
133 .dev = {
134 .platform_data = &ixdp425_i2c_gpio_data,
135 },
136};
137
138static struct resource ixdp425_uart_resources[] = {
139 {
140 .start = IXP4XX_UART1_BASE_PHYS,
141 .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
142 .flags = IORESOURCE_MEM
143 },
144 {
145 .start = IXP4XX_UART2_BASE_PHYS,
146 .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
147 .flags = IORESOURCE_MEM
148 }
149};
150
151static struct plat_serial8250_port ixdp425_uart_data[] = {
152 {
153 .mapbase = IXP4XX_UART1_BASE_PHYS,
154 .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
155 .irq = IRQ_IXP4XX_UART1,
156 .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
157 .iotype = UPIO_MEM,
158 .regshift = 2,
159 .uartclk = IXP4XX_UART_XTAL,
160 },
161 {
162 .mapbase = IXP4XX_UART2_BASE_PHYS,
163 .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
164 .irq = IRQ_IXP4XX_UART2,
165 .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
166 .iotype = UPIO_MEM,
167 .regshift = 2,
168 .uartclk = IXP4XX_UART_XTAL,
169 },
170 { },
171};
172
173static struct platform_device ixdp425_uart = {
174 .name = "serial8250",
175 .id = PLAT8250_DEV_PLATFORM,
176 .dev.platform_data = ixdp425_uart_data,
177 .num_resources = 2,
178 .resource = ixdp425_uart_resources
179};
180
181/* Built-in 10/100 Ethernet MAC interfaces */
182static struct eth_plat_info ixdp425_plat_eth[] = {
183 {
184 .phy = 0,
185 .rxq = 3,
186 .txreadyq = 20,
187 }, {
188 .phy = 1,
189 .rxq = 4,
190 .txreadyq = 21,
191 }
192};
193
194static struct platform_device ixdp425_eth[] = {
195 {
196 .name = "ixp4xx_eth",
197 .id = IXP4XX_ETH_NPEB,
198 .dev.platform_data = ixdp425_plat_eth,
199 }, {
200 .name = "ixp4xx_eth",
201 .id = IXP4XX_ETH_NPEC,
202 .dev.platform_data = ixdp425_plat_eth + 1,
203 }
204};
205
206static struct platform_device *ixdp425_devices[] __initdata = {
207 &ixdp425_i2c_gpio,
208 &ixdp425_flash,
209#if defined(CONFIG_MTD_NAND_PLATFORM) || \
210 defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
211 &ixdp425_flash_nand,
212#endif
213 &ixdp425_uart,
214 &ixdp425_eth[0],
215 &ixdp425_eth[1],
216};
217
218static void __init ixdp425_init(void)
219{
220 ixp4xx_sys_init();
221
222 ixdp425_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
223 ixdp425_flash_resource.end =
224 IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
225
226#if defined(CONFIG_MTD_NAND_PLATFORM) || \
227 defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
228 ixdp425_flash_nand_resource.start = IXP4XX_EXP_BUS_BASE(3),
229 ixdp425_flash_nand_resource.end = IXP4XX_EXP_BUS_BASE(3) + 0x10 - 1;
230
231 gpio_request(IXDP425_NAND_NCE_PIN, "NAND NCE pin");
232 gpio_direction_output(IXDP425_NAND_NCE_PIN, 0);
233
234 /* Configure expansion bus for NAND Flash */
235 *IXP4XX_EXP_CS3 = IXP4XX_EXP_BUS_CS_EN |
236 IXP4XX_EXP_BUS_STROBE_T(1) | /* extend by 1 clock */
237 IXP4XX_EXP_BUS_CYCLES(0) | /* Intel cycles */
238 IXP4XX_EXP_BUS_SIZE(0) | /* 512bytes addr space*/
239 IXP4XX_EXP_BUS_WR_EN |
240 IXP4XX_EXP_BUS_BYTE_EN; /* 8 bit data bus */
241#endif
242
243 if (cpu_is_ixp43x()) {
244 ixdp425_uart.num_resources = 1;
245 ixdp425_uart_data[1].flags = 0;
246 }
247
248 platform_add_devices(ixdp425_devices, ARRAY_SIZE(ixdp425_devices));
249}
250
251#ifdef CONFIG_ARCH_IXDP425
252MACHINE_START(IXDP425, "Intel IXDP425 Development Platform")
253 /* Maintainer: MontaVista Software, Inc. */
254 .map_io = ixp4xx_map_io,
255 .init_early = ixp4xx_init_early,
256 .init_irq = ixp4xx_init_irq,
257 .init_time = ixp4xx_timer_init,
258 .atag_offset = 0x100,
259 .init_machine = ixdp425_init,
260#if defined(CONFIG_PCI)
261 .dma_zone_size = SZ_64M,
262#endif
263 .restart = ixp4xx_restart,
264MACHINE_END
265#endif
266
267#ifdef CONFIG_MACH_IXDP465
268MACHINE_START(IXDP465, "Intel IXDP465 Development Platform")
269 /* Maintainer: MontaVista Software, Inc. */
270 .map_io = ixp4xx_map_io,
271 .init_early = ixp4xx_init_early,
272 .init_irq = ixp4xx_init_irq,
273 .init_time = ixp4xx_timer_init,
274 .atag_offset = 0x100,
275 .init_machine = ixdp425_init,
276#if defined(CONFIG_PCI)
277 .dma_zone_size = SZ_64M,
278#endif
279MACHINE_END
280#endif
281
282#ifdef CONFIG_ARCH_PRPMC1100
283MACHINE_START(IXCDP1100, "Intel IXCDP1100 Development Platform")
284 /* Maintainer: MontaVista Software, Inc. */
285 .map_io = ixp4xx_map_io,
286 .init_early = ixp4xx_init_early,
287 .init_irq = ixp4xx_init_irq,
288 .init_time = ixp4xx_timer_init,
289 .atag_offset = 0x100,
290 .init_machine = ixdp425_init,
291#if defined(CONFIG_PCI)
292 .dma_zone_size = SZ_64M,
293#endif
294MACHINE_END
295#endif
296
297#ifdef CONFIG_MACH_KIXRP435
298MACHINE_START(KIXRP435, "Intel KIXRP435 Reference Platform")
299 /* Maintainer: MontaVista Software, Inc. */
300 .map_io = ixp4xx_map_io,
301 .init_early = ixp4xx_init_early,
302 .init_irq = ixp4xx_init_irq,
303 .init_time = ixp4xx_timer_init,
304 .atag_offset = 0x100,
305 .init_machine = ixdp425_init,
306#if defined(CONFIG_PCI)
307 .dma_zone_size = SZ_64M,
308#endif
309MACHINE_END
310#endif