Loading...
1/*
2 * Freescale eSDHC i.MX controller driver for the platform bus.
3 *
4 * derived from the OF-version.
5 *
6 * Copyright (c) 2010 Pengutronix e.K.
7 * Author: Wolfram Sang <w.sang@pengutronix.de>
8 *
9 * This program is free software; you can redistribute it and/or modify
10 * it under the terms of the GNU General Public License as published by
11 * the Free Software Foundation; either version 2 of the License.
12 */
13
14#include <linux/io.h>
15#include <linux/delay.h>
16#include <linux/err.h>
17#include <linux/clk.h>
18#include <linux/gpio.h>
19#include <linux/module.h>
20#include <linux/slab.h>
21#include <linux/mmc/host.h>
22#include <linux/mmc/mmc.h>
23#include <linux/mmc/sdio.h>
24#include <linux/mmc/slot-gpio.h>
25#include <linux/of.h>
26#include <linux/of_device.h>
27#include <linux/of_gpio.h>
28#include <linux/pinctrl/consumer.h>
29#include <linux/platform_data/mmc-esdhc-imx.h>
30#include <linux/pm_runtime.h>
31#include "sdhci-pltfm.h"
32#include "sdhci-esdhc.h"
33
34#define ESDHC_CTRL_D3CD 0x08
35/* VENDOR SPEC register */
36#define ESDHC_VENDOR_SPEC 0xc0
37#define ESDHC_VENDOR_SPEC_SDIO_QUIRK (1 << 1)
38#define ESDHC_VENDOR_SPEC_VSELECT (1 << 1)
39#define ESDHC_VENDOR_SPEC_FRC_SDCLK_ON (1 << 8)
40#define ESDHC_WTMK_LVL 0x44
41#define ESDHC_MIX_CTRL 0x48
42#define ESDHC_MIX_CTRL_DDREN (1 << 3)
43#define ESDHC_MIX_CTRL_AC23EN (1 << 7)
44#define ESDHC_MIX_CTRL_EXE_TUNE (1 << 22)
45#define ESDHC_MIX_CTRL_SMPCLK_SEL (1 << 23)
46#define ESDHC_MIX_CTRL_FBCLK_SEL (1 << 25)
47/* Bits 3 and 6 are not SDHCI standard definitions */
48#define ESDHC_MIX_CTRL_SDHCI_MASK 0xb7
49/* Tuning bits */
50#define ESDHC_MIX_CTRL_TUNING_MASK 0x03c00000
51
52/* dll control register */
53#define ESDHC_DLL_CTRL 0x60
54#define ESDHC_DLL_OVERRIDE_VAL_SHIFT 9
55#define ESDHC_DLL_OVERRIDE_EN_SHIFT 8
56
57/* tune control register */
58#define ESDHC_TUNE_CTRL_STATUS 0x68
59#define ESDHC_TUNE_CTRL_STEP 1
60#define ESDHC_TUNE_CTRL_MIN 0
61#define ESDHC_TUNE_CTRL_MAX ((1 << 7) - 1)
62
63#define ESDHC_TUNING_CTRL 0xcc
64#define ESDHC_STD_TUNING_EN (1 << 24)
65/* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
66#define ESDHC_TUNING_START_TAP 0x1
67
68#define ESDHC_TUNING_BLOCK_PATTERN_LEN 64
69
70/* pinctrl state */
71#define ESDHC_PINCTRL_STATE_100MHZ "state_100mhz"
72#define ESDHC_PINCTRL_STATE_200MHZ "state_200mhz"
73
74/*
75 * Our interpretation of the SDHCI_HOST_CONTROL register
76 */
77#define ESDHC_CTRL_4BITBUS (0x1 << 1)
78#define ESDHC_CTRL_8BITBUS (0x2 << 1)
79#define ESDHC_CTRL_BUSWIDTH_MASK (0x3 << 1)
80
81/*
82 * There is an INT DMA ERR mis-match between eSDHC and STD SDHC SPEC:
83 * Bit25 is used in STD SPEC, and is reserved in fsl eSDHC design,
84 * but bit28 is used as the INT DMA ERR in fsl eSDHC design.
85 * Define this macro DMA error INT for fsl eSDHC
86 */
87#define ESDHC_INT_VENDOR_SPEC_DMA_ERR (1 << 28)
88
89/*
90 * The CMDTYPE of the CMD register (offset 0xE) should be set to
91 * "11" when the STOP CMD12 is issued on imx53 to abort one
92 * open ended multi-blk IO. Otherwise the TC INT wouldn't
93 * be generated.
94 * In exact block transfer, the controller doesn't complete the
95 * operations automatically as required at the end of the
96 * transfer and remains on hold if the abort command is not sent.
97 * As a result, the TC flag is not asserted and SW received timeout
98 * exeception. Bit1 of Vendor Spec registor is used to fix it.
99 */
100#define ESDHC_FLAG_MULTIBLK_NO_INT BIT(1)
101/*
102 * The flag enables the workaround for ESDHC errata ENGcm07207 which
103 * affects i.MX25 and i.MX35.
104 */
105#define ESDHC_FLAG_ENGCM07207 BIT(2)
106/*
107 * The flag tells that the ESDHC controller is an USDHC block that is
108 * integrated on the i.MX6 series.
109 */
110#define ESDHC_FLAG_USDHC BIT(3)
111/* The IP supports manual tuning process */
112#define ESDHC_FLAG_MAN_TUNING BIT(4)
113/* The IP supports standard tuning process */
114#define ESDHC_FLAG_STD_TUNING BIT(5)
115/* The IP has SDHCI_CAPABILITIES_1 register */
116#define ESDHC_FLAG_HAVE_CAP1 BIT(6)
117
118struct esdhc_soc_data {
119 u32 flags;
120};
121
122static struct esdhc_soc_data esdhc_imx25_data = {
123 .flags = ESDHC_FLAG_ENGCM07207,
124};
125
126static struct esdhc_soc_data esdhc_imx35_data = {
127 .flags = ESDHC_FLAG_ENGCM07207,
128};
129
130static struct esdhc_soc_data esdhc_imx51_data = {
131 .flags = 0,
132};
133
134static struct esdhc_soc_data esdhc_imx53_data = {
135 .flags = ESDHC_FLAG_MULTIBLK_NO_INT,
136};
137
138static struct esdhc_soc_data usdhc_imx6q_data = {
139 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_MAN_TUNING,
140};
141
142static struct esdhc_soc_data usdhc_imx6sl_data = {
143 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
144 | ESDHC_FLAG_HAVE_CAP1,
145};
146
147struct pltfm_imx_data {
148 u32 scratchpad;
149 struct pinctrl *pinctrl;
150 struct pinctrl_state *pins_default;
151 struct pinctrl_state *pins_100mhz;
152 struct pinctrl_state *pins_200mhz;
153 const struct esdhc_soc_data *socdata;
154 struct esdhc_platform_data boarddata;
155 struct clk *clk_ipg;
156 struct clk *clk_ahb;
157 struct clk *clk_per;
158 enum {
159 NO_CMD_PENDING, /* no multiblock command pending*/
160 MULTIBLK_IN_PROCESS, /* exact multiblock cmd in process */
161 WAIT_FOR_INT, /* sent CMD12, waiting for response INT */
162 } multiblock_status;
163 u32 uhs_mode;
164 u32 is_ddr;
165};
166
167static struct platform_device_id imx_esdhc_devtype[] = {
168 {
169 .name = "sdhci-esdhc-imx25",
170 .driver_data = (kernel_ulong_t) &esdhc_imx25_data,
171 }, {
172 .name = "sdhci-esdhc-imx35",
173 .driver_data = (kernel_ulong_t) &esdhc_imx35_data,
174 }, {
175 .name = "sdhci-esdhc-imx51",
176 .driver_data = (kernel_ulong_t) &esdhc_imx51_data,
177 }, {
178 /* sentinel */
179 }
180};
181MODULE_DEVICE_TABLE(platform, imx_esdhc_devtype);
182
183static const struct of_device_id imx_esdhc_dt_ids[] = {
184 { .compatible = "fsl,imx25-esdhc", .data = &esdhc_imx25_data, },
185 { .compatible = "fsl,imx35-esdhc", .data = &esdhc_imx35_data, },
186 { .compatible = "fsl,imx51-esdhc", .data = &esdhc_imx51_data, },
187 { .compatible = "fsl,imx53-esdhc", .data = &esdhc_imx53_data, },
188 { .compatible = "fsl,imx6sl-usdhc", .data = &usdhc_imx6sl_data, },
189 { .compatible = "fsl,imx6q-usdhc", .data = &usdhc_imx6q_data, },
190 { /* sentinel */ }
191};
192MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids);
193
194static inline int is_imx25_esdhc(struct pltfm_imx_data *data)
195{
196 return data->socdata == &esdhc_imx25_data;
197}
198
199static inline int is_imx53_esdhc(struct pltfm_imx_data *data)
200{
201 return data->socdata == &esdhc_imx53_data;
202}
203
204static inline int is_imx6q_usdhc(struct pltfm_imx_data *data)
205{
206 return data->socdata == &usdhc_imx6q_data;
207}
208
209static inline int esdhc_is_usdhc(struct pltfm_imx_data *data)
210{
211 return !!(data->socdata->flags & ESDHC_FLAG_USDHC);
212}
213
214static inline void esdhc_clrset_le(struct sdhci_host *host, u32 mask, u32 val, int reg)
215{
216 void __iomem *base = host->ioaddr + (reg & ~0x3);
217 u32 shift = (reg & 0x3) * 8;
218
219 writel(((readl(base) & ~(mask << shift)) | (val << shift)), base);
220}
221
222static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
223{
224 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
225 struct pltfm_imx_data *imx_data = pltfm_host->priv;
226 u32 val = readl(host->ioaddr + reg);
227
228 if (unlikely(reg == SDHCI_PRESENT_STATE)) {
229 u32 fsl_prss = val;
230 /* save the least 20 bits */
231 val = fsl_prss & 0x000FFFFF;
232 /* move dat[0-3] bits */
233 val |= (fsl_prss & 0x0F000000) >> 4;
234 /* move cmd line bit */
235 val |= (fsl_prss & 0x00800000) << 1;
236 }
237
238 if (unlikely(reg == SDHCI_CAPABILITIES)) {
239 /* ignore bit[0-15] as it stores cap_1 register val for mx6sl */
240 if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1)
241 val &= 0xffff0000;
242
243 /* In FSL esdhc IC module, only bit20 is used to indicate the
244 * ADMA2 capability of esdhc, but this bit is messed up on
245 * some SOCs (e.g. on MX25, MX35 this bit is set, but they
246 * don't actually support ADMA2). So set the BROKEN_ADMA
247 * uirk on MX25/35 platforms.
248 */
249
250 if (val & SDHCI_CAN_DO_ADMA1) {
251 val &= ~SDHCI_CAN_DO_ADMA1;
252 val |= SDHCI_CAN_DO_ADMA2;
253 }
254 }
255
256 if (unlikely(reg == SDHCI_CAPABILITIES_1)) {
257 if (esdhc_is_usdhc(imx_data)) {
258 if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1)
259 val = readl(host->ioaddr + SDHCI_CAPABILITIES) & 0xFFFF;
260 else
261 /* imx6q/dl does not have cap_1 register, fake one */
262 val = SDHCI_SUPPORT_DDR50 | SDHCI_SUPPORT_SDR104
263 | SDHCI_SUPPORT_SDR50
264 | SDHCI_USE_SDR50_TUNING;
265 }
266 }
267
268 if (unlikely(reg == SDHCI_MAX_CURRENT) && esdhc_is_usdhc(imx_data)) {
269 val = 0;
270 val |= 0xFF << SDHCI_MAX_CURRENT_330_SHIFT;
271 val |= 0xFF << SDHCI_MAX_CURRENT_300_SHIFT;
272 val |= 0xFF << SDHCI_MAX_CURRENT_180_SHIFT;
273 }
274
275 if (unlikely(reg == SDHCI_INT_STATUS)) {
276 if (val & ESDHC_INT_VENDOR_SPEC_DMA_ERR) {
277 val &= ~ESDHC_INT_VENDOR_SPEC_DMA_ERR;
278 val |= SDHCI_INT_ADMA_ERROR;
279 }
280
281 /*
282 * mask off the interrupt we get in response to the manually
283 * sent CMD12
284 */
285 if ((imx_data->multiblock_status == WAIT_FOR_INT) &&
286 ((val & SDHCI_INT_RESPONSE) == SDHCI_INT_RESPONSE)) {
287 val &= ~SDHCI_INT_RESPONSE;
288 writel(SDHCI_INT_RESPONSE, host->ioaddr +
289 SDHCI_INT_STATUS);
290 imx_data->multiblock_status = NO_CMD_PENDING;
291 }
292 }
293
294 return val;
295}
296
297static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg)
298{
299 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
300 struct pltfm_imx_data *imx_data = pltfm_host->priv;
301 u32 data;
302
303 if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE)) {
304 if (val & SDHCI_INT_CARD_INT) {
305 /*
306 * Clear and then set D3CD bit to avoid missing the
307 * card interrupt. This is a eSDHC controller problem
308 * so we need to apply the following workaround: clear
309 * and set D3CD bit will make eSDHC re-sample the card
310 * interrupt. In case a card interrupt was lost,
311 * re-sample it by the following steps.
312 */
313 data = readl(host->ioaddr + SDHCI_HOST_CONTROL);
314 data &= ~ESDHC_CTRL_D3CD;
315 writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
316 data |= ESDHC_CTRL_D3CD;
317 writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
318 }
319 }
320
321 if (unlikely((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
322 && (reg == SDHCI_INT_STATUS)
323 && (val & SDHCI_INT_DATA_END))) {
324 u32 v;
325 v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
326 v &= ~ESDHC_VENDOR_SPEC_SDIO_QUIRK;
327 writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
328
329 if (imx_data->multiblock_status == MULTIBLK_IN_PROCESS)
330 {
331 /* send a manual CMD12 with RESPTYP=none */
332 data = MMC_STOP_TRANSMISSION << 24 |
333 SDHCI_CMD_ABORTCMD << 16;
334 writel(data, host->ioaddr + SDHCI_TRANSFER_MODE);
335 imx_data->multiblock_status = WAIT_FOR_INT;
336 }
337 }
338
339 if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE)) {
340 if (val & SDHCI_INT_ADMA_ERROR) {
341 val &= ~SDHCI_INT_ADMA_ERROR;
342 val |= ESDHC_INT_VENDOR_SPEC_DMA_ERR;
343 }
344 }
345
346 writel(val, host->ioaddr + reg);
347}
348
349static u16 esdhc_readw_le(struct sdhci_host *host, int reg)
350{
351 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
352 struct pltfm_imx_data *imx_data = pltfm_host->priv;
353 u16 ret = 0;
354 u32 val;
355
356 if (unlikely(reg == SDHCI_HOST_VERSION)) {
357 reg ^= 2;
358 if (esdhc_is_usdhc(imx_data)) {
359 /*
360 * The usdhc register returns a wrong host version.
361 * Correct it here.
362 */
363 return SDHCI_SPEC_300;
364 }
365 }
366
367 if (unlikely(reg == SDHCI_HOST_CONTROL2)) {
368 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
369 if (val & ESDHC_VENDOR_SPEC_VSELECT)
370 ret |= SDHCI_CTRL_VDD_180;
371
372 if (esdhc_is_usdhc(imx_data)) {
373 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING)
374 val = readl(host->ioaddr + ESDHC_MIX_CTRL);
375 else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING)
376 /* the std tuning bits is in ACMD12_ERR for imx6sl */
377 val = readl(host->ioaddr + SDHCI_ACMD12_ERR);
378 }
379
380 if (val & ESDHC_MIX_CTRL_EXE_TUNE)
381 ret |= SDHCI_CTRL_EXEC_TUNING;
382 if (val & ESDHC_MIX_CTRL_SMPCLK_SEL)
383 ret |= SDHCI_CTRL_TUNED_CLK;
384
385 ret |= (imx_data->uhs_mode & SDHCI_CTRL_UHS_MASK);
386 ret &= ~SDHCI_CTRL_PRESET_VAL_ENABLE;
387
388 return ret;
389 }
390
391 if (unlikely(reg == SDHCI_TRANSFER_MODE)) {
392 if (esdhc_is_usdhc(imx_data)) {
393 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
394 ret = m & ESDHC_MIX_CTRL_SDHCI_MASK;
395 /* Swap AC23 bit */
396 if (m & ESDHC_MIX_CTRL_AC23EN) {
397 ret &= ~ESDHC_MIX_CTRL_AC23EN;
398 ret |= SDHCI_TRNS_AUTO_CMD23;
399 }
400 } else {
401 ret = readw(host->ioaddr + SDHCI_TRANSFER_MODE);
402 }
403
404 return ret;
405 }
406
407 return readw(host->ioaddr + reg);
408}
409
410static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
411{
412 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
413 struct pltfm_imx_data *imx_data = pltfm_host->priv;
414 u32 new_val = 0;
415
416 switch (reg) {
417 case SDHCI_CLOCK_CONTROL:
418 new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
419 if (val & SDHCI_CLOCK_CARD_EN)
420 new_val |= ESDHC_VENDOR_SPEC_FRC_SDCLK_ON;
421 else
422 new_val &= ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON;
423 writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC);
424 return;
425 case SDHCI_HOST_CONTROL2:
426 new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
427 if (val & SDHCI_CTRL_VDD_180)
428 new_val |= ESDHC_VENDOR_SPEC_VSELECT;
429 else
430 new_val &= ~ESDHC_VENDOR_SPEC_VSELECT;
431 writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC);
432 imx_data->uhs_mode = val & SDHCI_CTRL_UHS_MASK;
433 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) {
434 new_val = readl(host->ioaddr + ESDHC_MIX_CTRL);
435 if (val & SDHCI_CTRL_TUNED_CLK)
436 new_val |= ESDHC_MIX_CTRL_SMPCLK_SEL;
437 else
438 new_val &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
439 writel(new_val , host->ioaddr + ESDHC_MIX_CTRL);
440 } else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
441 u32 v = readl(host->ioaddr + SDHCI_ACMD12_ERR);
442 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
443 if (val & SDHCI_CTRL_TUNED_CLK) {
444 v |= ESDHC_MIX_CTRL_SMPCLK_SEL;
445 } else {
446 v &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
447 m &= ~ESDHC_MIX_CTRL_FBCLK_SEL;
448 }
449
450 if (val & SDHCI_CTRL_EXEC_TUNING) {
451 v |= ESDHC_MIX_CTRL_EXE_TUNE;
452 m |= ESDHC_MIX_CTRL_FBCLK_SEL;
453 } else {
454 v &= ~ESDHC_MIX_CTRL_EXE_TUNE;
455 }
456
457 writel(v, host->ioaddr + SDHCI_ACMD12_ERR);
458 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
459 }
460 return;
461 case SDHCI_TRANSFER_MODE:
462 if ((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
463 && (host->cmd->opcode == SD_IO_RW_EXTENDED)
464 && (host->cmd->data->blocks > 1)
465 && (host->cmd->data->flags & MMC_DATA_READ)) {
466 u32 v;
467 v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
468 v |= ESDHC_VENDOR_SPEC_SDIO_QUIRK;
469 writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
470 }
471
472 if (esdhc_is_usdhc(imx_data)) {
473 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
474 /* Swap AC23 bit */
475 if (val & SDHCI_TRNS_AUTO_CMD23) {
476 val &= ~SDHCI_TRNS_AUTO_CMD23;
477 val |= ESDHC_MIX_CTRL_AC23EN;
478 }
479 m = val | (m & ~ESDHC_MIX_CTRL_SDHCI_MASK);
480 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
481 } else {
482 /*
483 * Postpone this write, we must do it together with a
484 * command write that is down below.
485 */
486 imx_data->scratchpad = val;
487 }
488 return;
489 case SDHCI_COMMAND:
490 if (host->cmd->opcode == MMC_STOP_TRANSMISSION)
491 val |= SDHCI_CMD_ABORTCMD;
492
493 if ((host->cmd->opcode == MMC_SET_BLOCK_COUNT) &&
494 (imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
495 imx_data->multiblock_status = MULTIBLK_IN_PROCESS;
496
497 if (esdhc_is_usdhc(imx_data))
498 writel(val << 16,
499 host->ioaddr + SDHCI_TRANSFER_MODE);
500 else
501 writel(val << 16 | imx_data->scratchpad,
502 host->ioaddr + SDHCI_TRANSFER_MODE);
503 return;
504 case SDHCI_BLOCK_SIZE:
505 val &= ~SDHCI_MAKE_BLKSZ(0x7, 0);
506 break;
507 }
508 esdhc_clrset_le(host, 0xffff, val, reg);
509}
510
511static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg)
512{
513 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
514 struct pltfm_imx_data *imx_data = pltfm_host->priv;
515 u32 new_val;
516 u32 mask;
517
518 switch (reg) {
519 case SDHCI_POWER_CONTROL:
520 /*
521 * FSL put some DMA bits here
522 * If your board has a regulator, code should be here
523 */
524 return;
525 case SDHCI_HOST_CONTROL:
526 /* FSL messed up here, so we need to manually compose it. */
527 new_val = val & SDHCI_CTRL_LED;
528 /* ensure the endianness */
529 new_val |= ESDHC_HOST_CONTROL_LE;
530 /* bits 8&9 are reserved on mx25 */
531 if (!is_imx25_esdhc(imx_data)) {
532 /* DMA mode bits are shifted */
533 new_val |= (val & SDHCI_CTRL_DMA_MASK) << 5;
534 }
535
536 /*
537 * Do not touch buswidth bits here. This is done in
538 * esdhc_pltfm_bus_width.
539 * Do not touch the D3CD bit either which is used for the
540 * SDIO interrupt errata workaround.
541 */
542 mask = 0xffff & ~(ESDHC_CTRL_BUSWIDTH_MASK | ESDHC_CTRL_D3CD);
543
544 esdhc_clrset_le(host, mask, new_val, reg);
545 return;
546 }
547 esdhc_clrset_le(host, 0xff, val, reg);
548
549 /*
550 * The esdhc has a design violation to SDHC spec which tells
551 * that software reset should not affect card detection circuit.
552 * But esdhc clears its SYSCTL register bits [0..2] during the
553 * software reset. This will stop those clocks that card detection
554 * circuit relies on. To work around it, we turn the clocks on back
555 * to keep card detection circuit functional.
556 */
557 if ((reg == SDHCI_SOFTWARE_RESET) && (val & 1)) {
558 esdhc_clrset_le(host, 0x7, 0x7, ESDHC_SYSTEM_CONTROL);
559 /*
560 * The reset on usdhc fails to clear MIX_CTRL register.
561 * Do it manually here.
562 */
563 if (esdhc_is_usdhc(imx_data)) {
564 /* the tuning bits should be kept during reset */
565 new_val = readl(host->ioaddr + ESDHC_MIX_CTRL);
566 writel(new_val & ESDHC_MIX_CTRL_TUNING_MASK,
567 host->ioaddr + ESDHC_MIX_CTRL);
568 imx_data->is_ddr = 0;
569 }
570 }
571}
572
573static unsigned int esdhc_pltfm_get_max_clock(struct sdhci_host *host)
574{
575 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
576 struct pltfm_imx_data *imx_data = pltfm_host->priv;
577 struct esdhc_platform_data *boarddata = &imx_data->boarddata;
578
579 if (boarddata->f_max && (boarddata->f_max < pltfm_host->clock))
580 return boarddata->f_max;
581 else
582 return pltfm_host->clock;
583}
584
585static unsigned int esdhc_pltfm_get_min_clock(struct sdhci_host *host)
586{
587 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
588
589 return pltfm_host->clock / 256 / 16;
590}
591
592static inline void esdhc_pltfm_set_clock(struct sdhci_host *host,
593 unsigned int clock)
594{
595 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
596 struct pltfm_imx_data *imx_data = pltfm_host->priv;
597 unsigned int host_clock = pltfm_host->clock;
598 int pre_div = 2;
599 int div = 1;
600 u32 temp, val;
601
602 if (clock == 0) {
603 if (esdhc_is_usdhc(imx_data)) {
604 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
605 writel(val & ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
606 host->ioaddr + ESDHC_VENDOR_SPEC);
607 }
608 goto out;
609 }
610
611 if (esdhc_is_usdhc(imx_data) && !imx_data->is_ddr)
612 pre_div = 1;
613
614 temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
615 temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
616 | ESDHC_CLOCK_MASK);
617 sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
618
619 while (host_clock / pre_div / 16 > clock && pre_div < 256)
620 pre_div *= 2;
621
622 while (host_clock / pre_div / div > clock && div < 16)
623 div++;
624
625 host->mmc->actual_clock = host_clock / pre_div / div;
626 dev_dbg(mmc_dev(host->mmc), "desired SD clock: %d, actual: %d\n",
627 clock, host->mmc->actual_clock);
628
629 if (imx_data->is_ddr)
630 pre_div >>= 2;
631 else
632 pre_div >>= 1;
633 div--;
634
635 temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
636 temp |= (ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
637 | (div << ESDHC_DIVIDER_SHIFT)
638 | (pre_div << ESDHC_PREDIV_SHIFT));
639 sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
640
641 if (esdhc_is_usdhc(imx_data)) {
642 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
643 writel(val | ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
644 host->ioaddr + ESDHC_VENDOR_SPEC);
645 }
646
647 mdelay(1);
648out:
649 host->clock = clock;
650}
651
652static unsigned int esdhc_pltfm_get_ro(struct sdhci_host *host)
653{
654 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
655 struct pltfm_imx_data *imx_data = pltfm_host->priv;
656 struct esdhc_platform_data *boarddata = &imx_data->boarddata;
657
658 switch (boarddata->wp_type) {
659 case ESDHC_WP_GPIO:
660 return mmc_gpio_get_ro(host->mmc);
661 case ESDHC_WP_CONTROLLER:
662 return !(readl(host->ioaddr + SDHCI_PRESENT_STATE) &
663 SDHCI_WRITE_PROTECT);
664 case ESDHC_WP_NONE:
665 break;
666 }
667
668 return -ENOSYS;
669}
670
671static int esdhc_pltfm_bus_width(struct sdhci_host *host, int width)
672{
673 u32 ctrl;
674
675 switch (width) {
676 case MMC_BUS_WIDTH_8:
677 ctrl = ESDHC_CTRL_8BITBUS;
678 break;
679 case MMC_BUS_WIDTH_4:
680 ctrl = ESDHC_CTRL_4BITBUS;
681 break;
682 default:
683 ctrl = 0;
684 break;
685 }
686
687 esdhc_clrset_le(host, ESDHC_CTRL_BUSWIDTH_MASK, ctrl,
688 SDHCI_HOST_CONTROL);
689
690 return 0;
691}
692
693static void esdhc_prepare_tuning(struct sdhci_host *host, u32 val)
694{
695 u32 reg;
696
697 /* FIXME: delay a bit for card to be ready for next tuning due to errors */
698 mdelay(1);
699
700 pm_runtime_get_sync(host->mmc->parent);
701 reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
702 reg |= ESDHC_MIX_CTRL_EXE_TUNE | ESDHC_MIX_CTRL_SMPCLK_SEL |
703 ESDHC_MIX_CTRL_FBCLK_SEL;
704 writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
705 writel(val << 8, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
706 dev_dbg(mmc_dev(host->mmc),
707 "tunning with delay 0x%x ESDHC_TUNE_CTRL_STATUS 0x%x\n",
708 val, readl(host->ioaddr + ESDHC_TUNE_CTRL_STATUS));
709}
710
711static void esdhc_request_done(struct mmc_request *mrq)
712{
713 complete(&mrq->completion);
714}
715
716static int esdhc_send_tuning_cmd(struct sdhci_host *host, u32 opcode)
717{
718 struct mmc_command cmd = {0};
719 struct mmc_request mrq = {NULL};
720 struct mmc_data data = {0};
721 struct scatterlist sg;
722 char tuning_pattern[ESDHC_TUNING_BLOCK_PATTERN_LEN];
723
724 cmd.opcode = opcode;
725 cmd.arg = 0;
726 cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
727
728 data.blksz = ESDHC_TUNING_BLOCK_PATTERN_LEN;
729 data.blocks = 1;
730 data.flags = MMC_DATA_READ;
731 data.sg = &sg;
732 data.sg_len = 1;
733
734 sg_init_one(&sg, tuning_pattern, sizeof(tuning_pattern));
735
736 mrq.cmd = &cmd;
737 mrq.cmd->mrq = &mrq;
738 mrq.data = &data;
739 mrq.data->mrq = &mrq;
740 mrq.cmd->data = mrq.data;
741
742 mrq.done = esdhc_request_done;
743 init_completion(&(mrq.completion));
744
745 disable_irq(host->irq);
746 spin_lock(&host->lock);
747 host->mrq = &mrq;
748
749 sdhci_send_command(host, mrq.cmd);
750
751 spin_unlock(&host->lock);
752 enable_irq(host->irq);
753
754 wait_for_completion(&mrq.completion);
755
756 if (cmd.error)
757 return cmd.error;
758 if (data.error)
759 return data.error;
760
761 return 0;
762}
763
764static void esdhc_post_tuning(struct sdhci_host *host)
765{
766 u32 reg;
767
768 reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
769 reg &= ~ESDHC_MIX_CTRL_EXE_TUNE;
770 writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
771}
772
773static int esdhc_executing_tuning(struct sdhci_host *host, u32 opcode)
774{
775 int min, max, avg, ret;
776
777 /* find the mininum delay first which can pass tuning */
778 min = ESDHC_TUNE_CTRL_MIN;
779 while (min < ESDHC_TUNE_CTRL_MAX) {
780 esdhc_prepare_tuning(host, min);
781 if (!esdhc_send_tuning_cmd(host, opcode))
782 break;
783 min += ESDHC_TUNE_CTRL_STEP;
784 }
785
786 /* find the maxinum delay which can not pass tuning */
787 max = min + ESDHC_TUNE_CTRL_STEP;
788 while (max < ESDHC_TUNE_CTRL_MAX) {
789 esdhc_prepare_tuning(host, max);
790 if (esdhc_send_tuning_cmd(host, opcode)) {
791 max -= ESDHC_TUNE_CTRL_STEP;
792 break;
793 }
794 max += ESDHC_TUNE_CTRL_STEP;
795 }
796
797 /* use average delay to get the best timing */
798 avg = (min + max) / 2;
799 esdhc_prepare_tuning(host, avg);
800 ret = esdhc_send_tuning_cmd(host, opcode);
801 esdhc_post_tuning(host);
802
803 dev_dbg(mmc_dev(host->mmc), "tunning %s at 0x%x ret %d\n",
804 ret ? "failed" : "passed", avg, ret);
805
806 return ret;
807}
808
809static int esdhc_change_pinstate(struct sdhci_host *host,
810 unsigned int uhs)
811{
812 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
813 struct pltfm_imx_data *imx_data = pltfm_host->priv;
814 struct pinctrl_state *pinctrl;
815
816 dev_dbg(mmc_dev(host->mmc), "change pinctrl state for uhs %d\n", uhs);
817
818 if (IS_ERR(imx_data->pinctrl) ||
819 IS_ERR(imx_data->pins_default) ||
820 IS_ERR(imx_data->pins_100mhz) ||
821 IS_ERR(imx_data->pins_200mhz))
822 return -EINVAL;
823
824 switch (uhs) {
825 case MMC_TIMING_UHS_SDR50:
826 pinctrl = imx_data->pins_100mhz;
827 break;
828 case MMC_TIMING_UHS_SDR104:
829 case MMC_TIMING_MMC_HS200:
830 pinctrl = imx_data->pins_200mhz;
831 break;
832 default:
833 /* back to default state for other legacy timing */
834 pinctrl = imx_data->pins_default;
835 }
836
837 return pinctrl_select_state(imx_data->pinctrl, pinctrl);
838}
839
840static int esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs)
841{
842 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
843 struct pltfm_imx_data *imx_data = pltfm_host->priv;
844 struct esdhc_platform_data *boarddata = &imx_data->boarddata;
845
846 switch (uhs) {
847 case MMC_TIMING_UHS_SDR12:
848 imx_data->uhs_mode = SDHCI_CTRL_UHS_SDR12;
849 break;
850 case MMC_TIMING_UHS_SDR25:
851 imx_data->uhs_mode = SDHCI_CTRL_UHS_SDR25;
852 break;
853 case MMC_TIMING_UHS_SDR50:
854 imx_data->uhs_mode = SDHCI_CTRL_UHS_SDR50;
855 break;
856 case MMC_TIMING_UHS_SDR104:
857 case MMC_TIMING_MMC_HS200:
858 imx_data->uhs_mode = SDHCI_CTRL_UHS_SDR104;
859 break;
860 case MMC_TIMING_UHS_DDR50:
861 imx_data->uhs_mode = SDHCI_CTRL_UHS_DDR50;
862 writel(readl(host->ioaddr + ESDHC_MIX_CTRL) |
863 ESDHC_MIX_CTRL_DDREN,
864 host->ioaddr + ESDHC_MIX_CTRL);
865 imx_data->is_ddr = 1;
866 if (boarddata->delay_line) {
867 u32 v;
868 v = boarddata->delay_line <<
869 ESDHC_DLL_OVERRIDE_VAL_SHIFT |
870 (1 << ESDHC_DLL_OVERRIDE_EN_SHIFT);
871 if (is_imx53_esdhc(imx_data))
872 v <<= 1;
873 writel(v, host->ioaddr + ESDHC_DLL_CTRL);
874 }
875 break;
876 }
877
878 return esdhc_change_pinstate(host, uhs);
879}
880
881static struct sdhci_ops sdhci_esdhc_ops = {
882 .read_l = esdhc_readl_le,
883 .read_w = esdhc_readw_le,
884 .write_l = esdhc_writel_le,
885 .write_w = esdhc_writew_le,
886 .write_b = esdhc_writeb_le,
887 .set_clock = esdhc_pltfm_set_clock,
888 .get_max_clock = esdhc_pltfm_get_max_clock,
889 .get_min_clock = esdhc_pltfm_get_min_clock,
890 .get_ro = esdhc_pltfm_get_ro,
891 .platform_bus_width = esdhc_pltfm_bus_width,
892 .set_uhs_signaling = esdhc_set_uhs_signaling,
893};
894
895static const struct sdhci_pltfm_data sdhci_esdhc_imx_pdata = {
896 .quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_NO_HISPD_BIT
897 | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
898 | SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC
899 | SDHCI_QUIRK_BROKEN_CARD_DETECTION,
900 .ops = &sdhci_esdhc_ops,
901};
902
903#ifdef CONFIG_OF
904static int
905sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
906 struct esdhc_platform_data *boarddata)
907{
908 struct device_node *np = pdev->dev.of_node;
909
910 if (!np)
911 return -ENODEV;
912
913 if (of_get_property(np, "non-removable", NULL))
914 boarddata->cd_type = ESDHC_CD_PERMANENT;
915
916 if (of_get_property(np, "fsl,cd-controller", NULL))
917 boarddata->cd_type = ESDHC_CD_CONTROLLER;
918
919 if (of_get_property(np, "fsl,wp-controller", NULL))
920 boarddata->wp_type = ESDHC_WP_CONTROLLER;
921
922 boarddata->cd_gpio = of_get_named_gpio(np, "cd-gpios", 0);
923 if (gpio_is_valid(boarddata->cd_gpio))
924 boarddata->cd_type = ESDHC_CD_GPIO;
925
926 boarddata->wp_gpio = of_get_named_gpio(np, "wp-gpios", 0);
927 if (gpio_is_valid(boarddata->wp_gpio))
928 boarddata->wp_type = ESDHC_WP_GPIO;
929
930 of_property_read_u32(np, "bus-width", &boarddata->max_bus_width);
931
932 of_property_read_u32(np, "max-frequency", &boarddata->f_max);
933
934 if (of_find_property(np, "no-1-8-v", NULL))
935 boarddata->support_vsel = false;
936 else
937 boarddata->support_vsel = true;
938
939 if (of_property_read_u32(np, "fsl,delay-line", &boarddata->delay_line))
940 boarddata->delay_line = 0;
941
942 return 0;
943}
944#else
945static inline int
946sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
947 struct esdhc_platform_data *boarddata)
948{
949 return -ENODEV;
950}
951#endif
952
953static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
954{
955 const struct of_device_id *of_id =
956 of_match_device(imx_esdhc_dt_ids, &pdev->dev);
957 struct sdhci_pltfm_host *pltfm_host;
958 struct sdhci_host *host;
959 struct esdhc_platform_data *boarddata;
960 int err;
961 struct pltfm_imx_data *imx_data;
962
963 host = sdhci_pltfm_init(pdev, &sdhci_esdhc_imx_pdata, 0);
964 if (IS_ERR(host))
965 return PTR_ERR(host);
966
967 pltfm_host = sdhci_priv(host);
968
969 imx_data = devm_kzalloc(&pdev->dev, sizeof(*imx_data), GFP_KERNEL);
970 if (!imx_data) {
971 err = -ENOMEM;
972 goto free_sdhci;
973 }
974
975 imx_data->socdata = of_id ? of_id->data : (struct esdhc_soc_data *)
976 pdev->id_entry->driver_data;
977 pltfm_host->priv = imx_data;
978
979 imx_data->clk_ipg = devm_clk_get(&pdev->dev, "ipg");
980 if (IS_ERR(imx_data->clk_ipg)) {
981 err = PTR_ERR(imx_data->clk_ipg);
982 goto free_sdhci;
983 }
984
985 imx_data->clk_ahb = devm_clk_get(&pdev->dev, "ahb");
986 if (IS_ERR(imx_data->clk_ahb)) {
987 err = PTR_ERR(imx_data->clk_ahb);
988 goto free_sdhci;
989 }
990
991 imx_data->clk_per = devm_clk_get(&pdev->dev, "per");
992 if (IS_ERR(imx_data->clk_per)) {
993 err = PTR_ERR(imx_data->clk_per);
994 goto free_sdhci;
995 }
996
997 pltfm_host->clk = imx_data->clk_per;
998 pltfm_host->clock = clk_get_rate(pltfm_host->clk);
999 clk_prepare_enable(imx_data->clk_per);
1000 clk_prepare_enable(imx_data->clk_ipg);
1001 clk_prepare_enable(imx_data->clk_ahb);
1002
1003 imx_data->pinctrl = devm_pinctrl_get(&pdev->dev);
1004 if (IS_ERR(imx_data->pinctrl)) {
1005 err = PTR_ERR(imx_data->pinctrl);
1006 goto disable_clk;
1007 }
1008
1009 imx_data->pins_default = pinctrl_lookup_state(imx_data->pinctrl,
1010 PINCTRL_STATE_DEFAULT);
1011 if (IS_ERR(imx_data->pins_default)) {
1012 err = PTR_ERR(imx_data->pins_default);
1013 dev_err(mmc_dev(host->mmc), "could not get default state\n");
1014 goto disable_clk;
1015 }
1016
1017 host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
1018
1019 if (imx_data->socdata->flags & ESDHC_FLAG_ENGCM07207)
1020 /* Fix errata ENGcm07207 present on i.MX25 and i.MX35 */
1021 host->quirks |= SDHCI_QUIRK_NO_MULTIBLOCK
1022 | SDHCI_QUIRK_BROKEN_ADMA;
1023
1024 /*
1025 * The imx6q ROM code will change the default watermark level setting
1026 * to something insane. Change it back here.
1027 */
1028 if (esdhc_is_usdhc(imx_data)) {
1029 writel(0x08100810, host->ioaddr + ESDHC_WTMK_LVL);
1030 host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
1031 host->mmc->caps |= MMC_CAP_1_8V_DDR;
1032 }
1033
1034 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING)
1035 sdhci_esdhc_ops.platform_execute_tuning =
1036 esdhc_executing_tuning;
1037
1038 if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING)
1039 writel(readl(host->ioaddr + ESDHC_TUNING_CTRL) |
1040 ESDHC_STD_TUNING_EN | ESDHC_TUNING_START_TAP,
1041 host->ioaddr + ESDHC_TUNING_CTRL);
1042
1043 boarddata = &imx_data->boarddata;
1044 if (sdhci_esdhc_imx_probe_dt(pdev, boarddata) < 0) {
1045 if (!host->mmc->parent->platform_data) {
1046 dev_err(mmc_dev(host->mmc), "no board data!\n");
1047 err = -EINVAL;
1048 goto disable_clk;
1049 }
1050 imx_data->boarddata = *((struct esdhc_platform_data *)
1051 host->mmc->parent->platform_data);
1052 }
1053
1054 /* write_protect */
1055 if (boarddata->wp_type == ESDHC_WP_GPIO) {
1056 err = mmc_gpio_request_ro(host->mmc, boarddata->wp_gpio);
1057 if (err) {
1058 dev_err(mmc_dev(host->mmc),
1059 "failed to request write-protect gpio!\n");
1060 goto disable_clk;
1061 }
1062 host->mmc->caps2 |= MMC_CAP2_RO_ACTIVE_HIGH;
1063 }
1064
1065 /* card_detect */
1066 switch (boarddata->cd_type) {
1067 case ESDHC_CD_GPIO:
1068 err = mmc_gpio_request_cd(host->mmc, boarddata->cd_gpio, 0);
1069 if (err) {
1070 dev_err(mmc_dev(host->mmc),
1071 "failed to request card-detect gpio!\n");
1072 goto disable_clk;
1073 }
1074 /* fall through */
1075
1076 case ESDHC_CD_CONTROLLER:
1077 /* we have a working card_detect back */
1078 host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION;
1079 break;
1080
1081 case ESDHC_CD_PERMANENT:
1082 host->mmc->caps |= MMC_CAP_NONREMOVABLE;
1083 break;
1084
1085 case ESDHC_CD_NONE:
1086 break;
1087 }
1088
1089 switch (boarddata->max_bus_width) {
1090 case 8:
1091 host->mmc->caps |= MMC_CAP_8_BIT_DATA | MMC_CAP_4_BIT_DATA;
1092 break;
1093 case 4:
1094 host->mmc->caps |= MMC_CAP_4_BIT_DATA;
1095 break;
1096 case 1:
1097 default:
1098 host->quirks |= SDHCI_QUIRK_FORCE_1_BIT_DATA;
1099 break;
1100 }
1101
1102 /* sdr50 and sdr104 needs work on 1.8v signal voltage */
1103 if ((boarddata->support_vsel) && esdhc_is_usdhc(imx_data)) {
1104 imx_data->pins_100mhz = pinctrl_lookup_state(imx_data->pinctrl,
1105 ESDHC_PINCTRL_STATE_100MHZ);
1106 imx_data->pins_200mhz = pinctrl_lookup_state(imx_data->pinctrl,
1107 ESDHC_PINCTRL_STATE_200MHZ);
1108 if (IS_ERR(imx_data->pins_100mhz) ||
1109 IS_ERR(imx_data->pins_200mhz)) {
1110 dev_warn(mmc_dev(host->mmc),
1111 "could not get ultra high speed state, work on normal mode\n");
1112 /* fall back to not support uhs by specify no 1.8v quirk */
1113 host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V;
1114 }
1115 } else {
1116 host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V;
1117 }
1118
1119 err = sdhci_add_host(host);
1120 if (err)
1121 goto disable_clk;
1122
1123 pm_runtime_set_active(&pdev->dev);
1124 pm_runtime_enable(&pdev->dev);
1125 pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
1126 pm_runtime_use_autosuspend(&pdev->dev);
1127 pm_suspend_ignore_children(&pdev->dev, 1);
1128
1129 return 0;
1130
1131disable_clk:
1132 clk_disable_unprepare(imx_data->clk_per);
1133 clk_disable_unprepare(imx_data->clk_ipg);
1134 clk_disable_unprepare(imx_data->clk_ahb);
1135free_sdhci:
1136 sdhci_pltfm_free(pdev);
1137 return err;
1138}
1139
1140static int sdhci_esdhc_imx_remove(struct platform_device *pdev)
1141{
1142 struct sdhci_host *host = platform_get_drvdata(pdev);
1143 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1144 struct pltfm_imx_data *imx_data = pltfm_host->priv;
1145 int dead = (readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff);
1146
1147 sdhci_remove_host(host, dead);
1148
1149 pm_runtime_dont_use_autosuspend(&pdev->dev);
1150 pm_runtime_disable(&pdev->dev);
1151
1152 if (!IS_ENABLED(CONFIG_PM_RUNTIME)) {
1153 clk_disable_unprepare(imx_data->clk_per);
1154 clk_disable_unprepare(imx_data->clk_ipg);
1155 clk_disable_unprepare(imx_data->clk_ahb);
1156 }
1157
1158 sdhci_pltfm_free(pdev);
1159
1160 return 0;
1161}
1162
1163#ifdef CONFIG_PM_RUNTIME
1164static int sdhci_esdhc_runtime_suspend(struct device *dev)
1165{
1166 struct sdhci_host *host = dev_get_drvdata(dev);
1167 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1168 struct pltfm_imx_data *imx_data = pltfm_host->priv;
1169 int ret;
1170
1171 ret = sdhci_runtime_suspend_host(host);
1172
1173 clk_disable_unprepare(imx_data->clk_per);
1174 clk_disable_unprepare(imx_data->clk_ipg);
1175 clk_disable_unprepare(imx_data->clk_ahb);
1176
1177 return ret;
1178}
1179
1180static int sdhci_esdhc_runtime_resume(struct device *dev)
1181{
1182 struct sdhci_host *host = dev_get_drvdata(dev);
1183 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1184 struct pltfm_imx_data *imx_data = pltfm_host->priv;
1185
1186 clk_prepare_enable(imx_data->clk_per);
1187 clk_prepare_enable(imx_data->clk_ipg);
1188 clk_prepare_enable(imx_data->clk_ahb);
1189
1190 return sdhci_runtime_resume_host(host);
1191}
1192#endif
1193
1194static const struct dev_pm_ops sdhci_esdhc_pmops = {
1195 SET_SYSTEM_SLEEP_PM_OPS(sdhci_pltfm_suspend, sdhci_pltfm_resume)
1196 SET_RUNTIME_PM_OPS(sdhci_esdhc_runtime_suspend,
1197 sdhci_esdhc_runtime_resume, NULL)
1198};
1199
1200static struct platform_driver sdhci_esdhc_imx_driver = {
1201 .driver = {
1202 .name = "sdhci-esdhc-imx",
1203 .owner = THIS_MODULE,
1204 .of_match_table = imx_esdhc_dt_ids,
1205 .pm = &sdhci_esdhc_pmops,
1206 },
1207 .id_table = imx_esdhc_devtype,
1208 .probe = sdhci_esdhc_imx_probe,
1209 .remove = sdhci_esdhc_imx_remove,
1210};
1211
1212module_platform_driver(sdhci_esdhc_imx_driver);
1213
1214MODULE_DESCRIPTION("SDHCI driver for Freescale i.MX eSDHC");
1215MODULE_AUTHOR("Wolfram Sang <w.sang@pengutronix.de>");
1216MODULE_LICENSE("GPL v2");
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Freescale eSDHC i.MX controller driver for the platform bus.
4 *
5 * derived from the OF-version.
6 *
7 * Copyright (c) 2010 Pengutronix e.K.
8 * Author: Wolfram Sang <kernel@pengutronix.de>
9 */
10
11#include <linux/bitfield.h>
12#include <linux/io.h>
13#include <linux/iopoll.h>
14#include <linux/delay.h>
15#include <linux/err.h>
16#include <linux/clk.h>
17#include <linux/module.h>
18#include <linux/slab.h>
19#include <linux/pm_qos.h>
20#include <linux/mmc/host.h>
21#include <linux/mmc/mmc.h>
22#include <linux/mmc/sdio.h>
23#include <linux/mmc/slot-gpio.h>
24#include <linux/of.h>
25#include <linux/platform_device.h>
26#include <linux/pinctrl/consumer.h>
27#include <linux/pm_runtime.h>
28#include "sdhci-cqhci.h"
29#include "sdhci-pltfm.h"
30#include "sdhci-esdhc.h"
31#include "cqhci.h"
32
33#define ESDHC_SYS_CTRL_DTOCV_MASK 0x0f
34#define ESDHC_CTRL_D3CD 0x08
35#define ESDHC_BURST_LEN_EN_INCR (1 << 27)
36/* VENDOR SPEC register */
37#define ESDHC_VENDOR_SPEC 0xc0
38#define ESDHC_VENDOR_SPEC_SDIO_QUIRK (1 << 1)
39#define ESDHC_VENDOR_SPEC_VSELECT (1 << 1)
40#define ESDHC_VENDOR_SPEC_FRC_SDCLK_ON (1 << 8)
41#define ESDHC_DEBUG_SEL_AND_STATUS_REG 0xc2
42#define ESDHC_DEBUG_SEL_REG 0xc3
43#define ESDHC_DEBUG_SEL_MASK 0xf
44#define ESDHC_DEBUG_SEL_CMD_STATE 1
45#define ESDHC_DEBUG_SEL_DATA_STATE 2
46#define ESDHC_DEBUG_SEL_TRANS_STATE 3
47#define ESDHC_DEBUG_SEL_DMA_STATE 4
48#define ESDHC_DEBUG_SEL_ADMA_STATE 5
49#define ESDHC_DEBUG_SEL_FIFO_STATE 6
50#define ESDHC_DEBUG_SEL_ASYNC_FIFO_STATE 7
51#define ESDHC_WTMK_LVL 0x44
52#define ESDHC_WTMK_DEFAULT_VAL 0x10401040
53#define ESDHC_WTMK_LVL_RD_WML_MASK 0x000000FF
54#define ESDHC_WTMK_LVL_RD_WML_SHIFT 0
55#define ESDHC_WTMK_LVL_WR_WML_MASK 0x00FF0000
56#define ESDHC_WTMK_LVL_WR_WML_SHIFT 16
57#define ESDHC_WTMK_LVL_WML_VAL_DEF 64
58#define ESDHC_WTMK_LVL_WML_VAL_MAX 128
59#define ESDHC_MIX_CTRL 0x48
60#define ESDHC_MIX_CTRL_DDREN (1 << 3)
61#define ESDHC_MIX_CTRL_AC23EN (1 << 7)
62#define ESDHC_MIX_CTRL_EXE_TUNE (1 << 22)
63#define ESDHC_MIX_CTRL_SMPCLK_SEL (1 << 23)
64#define ESDHC_MIX_CTRL_AUTO_TUNE_EN (1 << 24)
65#define ESDHC_MIX_CTRL_FBCLK_SEL (1 << 25)
66#define ESDHC_MIX_CTRL_HS400_EN (1 << 26)
67#define ESDHC_MIX_CTRL_HS400_ES_EN (1 << 27)
68/* Bits 3 and 6 are not SDHCI standard definitions */
69#define ESDHC_MIX_CTRL_SDHCI_MASK 0xb7
70/* Tuning bits */
71#define ESDHC_MIX_CTRL_TUNING_MASK 0x03c00000
72
73/* dll control register */
74#define ESDHC_DLL_CTRL 0x60
75#define ESDHC_DLL_OVERRIDE_VAL_SHIFT 9
76#define ESDHC_DLL_OVERRIDE_EN_SHIFT 8
77
78/* tune control register */
79#define ESDHC_TUNE_CTRL_STATUS 0x68
80#define ESDHC_TUNE_CTRL_STEP 1
81#define ESDHC_TUNE_CTRL_MIN 0
82#define ESDHC_TUNE_CTRL_MAX ((1 << 7) - 1)
83
84/* strobe dll register */
85#define ESDHC_STROBE_DLL_CTRL 0x70
86#define ESDHC_STROBE_DLL_CTRL_ENABLE (1 << 0)
87#define ESDHC_STROBE_DLL_CTRL_RESET (1 << 1)
88#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT 0x7
89#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT 3
90#define ESDHC_STROBE_DLL_CTRL_SLV_UPDATE_INT_DEFAULT (4 << 20)
91
92#define ESDHC_STROBE_DLL_STATUS 0x74
93#define ESDHC_STROBE_DLL_STS_REF_LOCK (1 << 1)
94#define ESDHC_STROBE_DLL_STS_SLV_LOCK 0x1
95
96#define ESDHC_VEND_SPEC2 0xc8
97#define ESDHC_VEND_SPEC2_EN_BUSY_IRQ (1 << 8)
98#define ESDHC_VEND_SPEC2_AUTO_TUNE_8BIT_EN (1 << 4)
99#define ESDHC_VEND_SPEC2_AUTO_TUNE_4BIT_EN (0 << 4)
100#define ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN (2 << 4)
101#define ESDHC_VEND_SPEC2_AUTO_TUNE_CMD_EN (1 << 6)
102#define ESDHC_VEND_SPEC2_AUTO_TUNE_MODE_MASK (7 << 4)
103
104#define ESDHC_TUNING_CTRL 0xcc
105#define ESDHC_STD_TUNING_EN (1 << 24)
106/* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
107#define ESDHC_TUNING_START_TAP_DEFAULT 0x1
108#define ESDHC_TUNING_START_TAP_MASK 0x7f
109#define ESDHC_TUNING_CMD_CRC_CHECK_DISABLE (1 << 7)
110#define ESDHC_TUNING_STEP_DEFAULT 0x1
111#define ESDHC_TUNING_STEP_MASK 0x00070000
112#define ESDHC_TUNING_STEP_SHIFT 16
113
114/* pinctrl state */
115#define ESDHC_PINCTRL_STATE_100MHZ "state_100mhz"
116#define ESDHC_PINCTRL_STATE_200MHZ "state_200mhz"
117
118/*
119 * Our interpretation of the SDHCI_HOST_CONTROL register
120 */
121#define ESDHC_CTRL_4BITBUS (0x1 << 1)
122#define ESDHC_CTRL_8BITBUS (0x2 << 1)
123#define ESDHC_CTRL_BUSWIDTH_MASK (0x3 << 1)
124#define USDHC_GET_BUSWIDTH(c) (c & ESDHC_CTRL_BUSWIDTH_MASK)
125
126/*
127 * There is an INT DMA ERR mismatch between eSDHC and STD SDHC SPEC:
128 * Bit25 is used in STD SPEC, and is reserved in fsl eSDHC design,
129 * but bit28 is used as the INT DMA ERR in fsl eSDHC design.
130 * Define this macro DMA error INT for fsl eSDHC
131 */
132#define ESDHC_INT_VENDOR_SPEC_DMA_ERR (1 << 28)
133
134/* the address offset of CQHCI */
135#define ESDHC_CQHCI_ADDR_OFFSET 0x100
136
137/*
138 * The CMDTYPE of the CMD register (offset 0xE) should be set to
139 * "11" when the STOP CMD12 is issued on imx53 to abort one
140 * open ended multi-blk IO. Otherwise the TC INT wouldn't
141 * be generated.
142 * In exact block transfer, the controller doesn't complete the
143 * operations automatically as required at the end of the
144 * transfer and remains on hold if the abort command is not sent.
145 * As a result, the TC flag is not asserted and SW received timeout
146 * exception. Bit1 of Vendor Spec register is used to fix it.
147 */
148#define ESDHC_FLAG_MULTIBLK_NO_INT BIT(1)
149/*
150 * The flag tells that the ESDHC controller is an USDHC block that is
151 * integrated on the i.MX6 series.
152 */
153#define ESDHC_FLAG_USDHC BIT(3)
154/* The IP supports manual tuning process */
155#define ESDHC_FLAG_MAN_TUNING BIT(4)
156/* The IP supports standard tuning process */
157#define ESDHC_FLAG_STD_TUNING BIT(5)
158/* The IP has SDHCI_CAPABILITIES_1 register */
159#define ESDHC_FLAG_HAVE_CAP1 BIT(6)
160/*
161 * The IP has erratum ERR004536
162 * uSDHC: ADMA Length Mismatch Error occurs if the AHB read access is slow,
163 * when reading data from the card
164 * This flag is also set for i.MX25 and i.MX35 in order to get
165 * SDHCI_QUIRK_BROKEN_ADMA, but for different reasons (ADMA capability bits).
166 */
167#define ESDHC_FLAG_ERR004536 BIT(7)
168/* The IP supports HS200 mode */
169#define ESDHC_FLAG_HS200 BIT(8)
170/* The IP supports HS400 mode */
171#define ESDHC_FLAG_HS400 BIT(9)
172/*
173 * The IP has errata ERR010450
174 * uSDHC: At 1.8V due to the I/O timing limit, for SDR mode, SD card
175 * clock can't exceed 150MHz, for DDR mode, SD card clock can't exceed 45MHz.
176 */
177#define ESDHC_FLAG_ERR010450 BIT(10)
178/* The IP supports HS400ES mode */
179#define ESDHC_FLAG_HS400_ES BIT(11)
180/* The IP has Host Controller Interface for Command Queuing */
181#define ESDHC_FLAG_CQHCI BIT(12)
182/* need request pmqos during low power */
183#define ESDHC_FLAG_PMQOS BIT(13)
184/* The IP state got lost in low power mode */
185#define ESDHC_FLAG_STATE_LOST_IN_LPMODE BIT(14)
186/* The IP lost clock rate in PM_RUNTIME */
187#define ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME BIT(15)
188/*
189 * The IP do not support the ACMD23 feature completely when use ADMA mode.
190 * In ADMA mode, it only use the 16 bit block count of the register 0x4
191 * (BLOCK_ATT) as the CMD23's argument for ACMD23 mode, which means it will
192 * ignore the upper 16 bit of the CMD23's argument. This will block the reliable
193 * write operation in RPMB, because RPMB reliable write need to set the bit31
194 * of the CMD23's argument.
195 * imx6qpdl/imx6sx/imx6sl/imx7d has this limitation only for ADMA mode, SDMA
196 * do not has this limitation. so when these SoC use ADMA mode, it need to
197 * disable the ACMD23 feature.
198 */
199#define ESDHC_FLAG_BROKEN_AUTO_CMD23 BIT(16)
200
201/* ERR004536 is not applicable for the IP */
202#define ESDHC_FLAG_SKIP_ERR004536 BIT(17)
203
204enum wp_types {
205 ESDHC_WP_NONE, /* no WP, neither controller nor gpio */
206 ESDHC_WP_CONTROLLER, /* mmc controller internal WP */
207 ESDHC_WP_GPIO, /* external gpio pin for WP */
208};
209
210enum cd_types {
211 ESDHC_CD_NONE, /* no CD, neither controller nor gpio */
212 ESDHC_CD_CONTROLLER, /* mmc controller internal CD */
213 ESDHC_CD_GPIO, /* external gpio pin for CD */
214 ESDHC_CD_PERMANENT, /* no CD, card permanently wired to host */
215};
216
217/*
218 * struct esdhc_platform_data - platform data for esdhc on i.MX
219 *
220 * ESDHC_WP(CD)_CONTROLLER type is not available on i.MX25/35.
221 *
222 * @wp_type: type of write_protect method (see wp_types enum above)
223 * @cd_type: type of card_detect method (see cd_types enum above)
224 */
225
226struct esdhc_platform_data {
227 enum wp_types wp_type;
228 enum cd_types cd_type;
229 int max_bus_width;
230 unsigned int delay_line;
231 unsigned int tuning_step; /* The delay cell steps in tuning procedure */
232 unsigned int tuning_start_tap; /* The start delay cell point in tuning procedure */
233 unsigned int strobe_dll_delay_target; /* The delay cell for strobe pad (read clock) */
234};
235
236struct esdhc_soc_data {
237 u32 flags;
238};
239
240static const struct esdhc_soc_data esdhc_imx25_data = {
241 .flags = ESDHC_FLAG_ERR004536,
242};
243
244static const struct esdhc_soc_data esdhc_imx35_data = {
245 .flags = ESDHC_FLAG_ERR004536,
246};
247
248static const struct esdhc_soc_data esdhc_imx51_data = {
249 .flags = 0,
250};
251
252static const struct esdhc_soc_data esdhc_imx53_data = {
253 .flags = ESDHC_FLAG_MULTIBLK_NO_INT,
254};
255
256static const struct esdhc_soc_data usdhc_imx6q_data = {
257 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_MAN_TUNING
258 | ESDHC_FLAG_BROKEN_AUTO_CMD23,
259};
260
261static const struct esdhc_soc_data usdhc_imx6sl_data = {
262 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
263 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_ERR004536
264 | ESDHC_FLAG_HS200
265 | ESDHC_FLAG_BROKEN_AUTO_CMD23,
266};
267
268static const struct esdhc_soc_data usdhc_imx6sll_data = {
269 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
270 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
271 | ESDHC_FLAG_HS400
272 | ESDHC_FLAG_STATE_LOST_IN_LPMODE,
273};
274
275static const struct esdhc_soc_data usdhc_imx6sx_data = {
276 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
277 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
278 | ESDHC_FLAG_STATE_LOST_IN_LPMODE
279 | ESDHC_FLAG_BROKEN_AUTO_CMD23,
280};
281
282static const struct esdhc_soc_data usdhc_imx6ull_data = {
283 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
284 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
285 | ESDHC_FLAG_ERR010450
286 | ESDHC_FLAG_STATE_LOST_IN_LPMODE,
287};
288
289static const struct esdhc_soc_data usdhc_imx7d_data = {
290 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
291 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
292 | ESDHC_FLAG_HS400
293 | ESDHC_FLAG_STATE_LOST_IN_LPMODE
294 | ESDHC_FLAG_BROKEN_AUTO_CMD23,
295};
296
297static struct esdhc_soc_data usdhc_s32g2_data = {
298 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_MAN_TUNING
299 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
300 | ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES
301 | ESDHC_FLAG_SKIP_ERR004536,
302};
303
304static struct esdhc_soc_data usdhc_imx7ulp_data = {
305 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
306 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
307 | ESDHC_FLAG_PMQOS | ESDHC_FLAG_HS400
308 | ESDHC_FLAG_STATE_LOST_IN_LPMODE,
309};
310static struct esdhc_soc_data usdhc_imxrt1050_data = {
311 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
312 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200,
313};
314
315static struct esdhc_soc_data usdhc_imx8qxp_data = {
316 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
317 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
318 | ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES
319 | ESDHC_FLAG_STATE_LOST_IN_LPMODE
320 | ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME,
321};
322
323static struct esdhc_soc_data usdhc_imx8mm_data = {
324 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
325 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
326 | ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES
327 | ESDHC_FLAG_STATE_LOST_IN_LPMODE,
328};
329
330struct pltfm_imx_data {
331 u32 scratchpad;
332 struct pinctrl *pinctrl;
333 struct pinctrl_state *pins_100mhz;
334 struct pinctrl_state *pins_200mhz;
335 const struct esdhc_soc_data *socdata;
336 struct esdhc_platform_data boarddata;
337 struct clk *clk_ipg;
338 struct clk *clk_ahb;
339 struct clk *clk_per;
340 unsigned int actual_clock;
341
342 /*
343 * USDHC has one limition, require the SDIO device a different
344 * register setting. Driver has to recognize card type during
345 * the card init, but at this stage, mmc_host->card is not
346 * available. So involve this field to save the card type
347 * during card init through usdhc_init_card().
348 */
349 unsigned int init_card_type;
350
351 enum {
352 NO_CMD_PENDING, /* no multiblock command pending */
353 MULTIBLK_IN_PROCESS, /* exact multiblock cmd in process */
354 WAIT_FOR_INT, /* sent CMD12, waiting for response INT */
355 } multiblock_status;
356 u32 is_ddr;
357 struct pm_qos_request pm_qos_req;
358};
359
360static const struct of_device_id imx_esdhc_dt_ids[] = {
361 { .compatible = "fsl,imx25-esdhc", .data = &esdhc_imx25_data, },
362 { .compatible = "fsl,imx35-esdhc", .data = &esdhc_imx35_data, },
363 { .compatible = "fsl,imx51-esdhc", .data = &esdhc_imx51_data, },
364 { .compatible = "fsl,imx53-esdhc", .data = &esdhc_imx53_data, },
365 { .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },
366 { .compatible = "fsl,imx6sl-usdhc", .data = &usdhc_imx6sl_data, },
367 { .compatible = "fsl,imx6sll-usdhc", .data = &usdhc_imx6sll_data, },
368 { .compatible = "fsl,imx6q-usdhc", .data = &usdhc_imx6q_data, },
369 { .compatible = "fsl,imx6ull-usdhc", .data = &usdhc_imx6ull_data, },
370 { .compatible = "fsl,imx7d-usdhc", .data = &usdhc_imx7d_data, },
371 { .compatible = "fsl,imx7ulp-usdhc", .data = &usdhc_imx7ulp_data, },
372 { .compatible = "fsl,imx8qxp-usdhc", .data = &usdhc_imx8qxp_data, },
373 { .compatible = "fsl,imx8mm-usdhc", .data = &usdhc_imx8mm_data, },
374 { .compatible = "fsl,imxrt1050-usdhc", .data = &usdhc_imxrt1050_data, },
375 { .compatible = "nxp,s32g2-usdhc", .data = &usdhc_s32g2_data, },
376 { /* sentinel */ }
377};
378MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids);
379
380static inline int is_imx25_esdhc(struct pltfm_imx_data *data)
381{
382 return data->socdata == &esdhc_imx25_data;
383}
384
385static inline int is_imx53_esdhc(struct pltfm_imx_data *data)
386{
387 return data->socdata == &esdhc_imx53_data;
388}
389
390static inline int esdhc_is_usdhc(struct pltfm_imx_data *data)
391{
392 return !!(data->socdata->flags & ESDHC_FLAG_USDHC);
393}
394
395static inline void esdhc_clrset_le(struct sdhci_host *host, u32 mask, u32 val, int reg)
396{
397 void __iomem *base = host->ioaddr + (reg & ~0x3);
398 u32 shift = (reg & 0x3) * 8;
399
400 writel(((readl(base) & ~(mask << shift)) | (val << shift)), base);
401}
402
403#define DRIVER_NAME "sdhci-esdhc-imx"
404#define ESDHC_IMX_DUMP(f, x...) \
405 pr_err("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x)
406static void esdhc_dump_debug_regs(struct sdhci_host *host)
407{
408 int i;
409 char *debug_status[7] = {
410 "cmd debug status",
411 "data debug status",
412 "trans debug status",
413 "dma debug status",
414 "adma debug status",
415 "fifo debug status",
416 "async fifo debug status"
417 };
418
419 ESDHC_IMX_DUMP("========= ESDHC IMX DEBUG STATUS DUMP =========\n");
420 for (i = 0; i < 7; i++) {
421 esdhc_clrset_le(host, ESDHC_DEBUG_SEL_MASK,
422 ESDHC_DEBUG_SEL_CMD_STATE + i, ESDHC_DEBUG_SEL_REG);
423 ESDHC_IMX_DUMP("%s: 0x%04x\n", debug_status[i],
424 readw(host->ioaddr + ESDHC_DEBUG_SEL_AND_STATUS_REG));
425 }
426
427 esdhc_clrset_le(host, ESDHC_DEBUG_SEL_MASK, 0, ESDHC_DEBUG_SEL_REG);
428
429}
430
431static inline void esdhc_wait_for_card_clock_gate_off(struct sdhci_host *host)
432{
433 u32 present_state;
434 int ret;
435
436 ret = readl_poll_timeout(host->ioaddr + ESDHC_PRSSTAT, present_state,
437 (present_state & ESDHC_CLOCK_GATE_OFF), 2, 100);
438 if (ret == -ETIMEDOUT)
439 dev_warn(mmc_dev(host->mmc), "%s: card clock still not gate off in 100us!.\n", __func__);
440}
441
442/* Enable the auto tuning circuit to check the CMD line and BUS line */
443static inline void usdhc_auto_tuning_mode_sel_and_en(struct sdhci_host *host)
444{
445 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
446 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
447 u32 buswidth, auto_tune_buswidth;
448 u32 reg;
449
450 buswidth = USDHC_GET_BUSWIDTH(readl(host->ioaddr + SDHCI_HOST_CONTROL));
451
452 switch (buswidth) {
453 case ESDHC_CTRL_8BITBUS:
454 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_8BIT_EN;
455 break;
456 case ESDHC_CTRL_4BITBUS:
457 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_4BIT_EN;
458 break;
459 default: /* 1BITBUS */
460 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN;
461 break;
462 }
463
464 /*
465 * For USDHC, auto tuning circuit can not handle the async sdio
466 * device interrupt correctly. When sdio device use 4 data lines,
467 * async sdio interrupt will use the shared DAT[1], if enable auto
468 * tuning circuit check these 4 data lines, include the DAT[1],
469 * this circuit will detect this interrupt, take this as a data on
470 * DAT[1], and adjust the delay cell wrongly.
471 * This is the hardware design limitation, to avoid this, for sdio
472 * device, config the auto tuning circuit only check DAT[0] and CMD
473 * line.
474 */
475 if (imx_data->init_card_type == MMC_TYPE_SDIO)
476 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN;
477
478 esdhc_clrset_le(host, ESDHC_VEND_SPEC2_AUTO_TUNE_MODE_MASK,
479 auto_tune_buswidth | ESDHC_VEND_SPEC2_AUTO_TUNE_CMD_EN,
480 ESDHC_VEND_SPEC2);
481
482 reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
483 reg |= ESDHC_MIX_CTRL_AUTO_TUNE_EN;
484 writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
485}
486
487static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
488{
489 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
490 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
491 u32 val = readl(host->ioaddr + reg);
492
493 if (unlikely(reg == SDHCI_PRESENT_STATE)) {
494 u32 fsl_prss = val;
495 /* save the least 20 bits */
496 val = fsl_prss & 0x000FFFFF;
497 /* move dat[0-3] bits */
498 val |= (fsl_prss & 0x0F000000) >> 4;
499 /* move cmd line bit */
500 val |= (fsl_prss & 0x00800000) << 1;
501 }
502
503 if (unlikely(reg == SDHCI_CAPABILITIES)) {
504 /* ignore bit[0-15] as it stores cap_1 register val for mx6sl */
505 if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1)
506 val &= 0xffff0000;
507
508 /* In FSL esdhc IC module, only bit20 is used to indicate the
509 * ADMA2 capability of esdhc, but this bit is messed up on
510 * some SOCs (e.g. on MX25, MX35 this bit is set, but they
511 * don't actually support ADMA2). So set the BROKEN_ADMA
512 * quirk on MX25/35 platforms.
513 */
514
515 if (val & SDHCI_CAN_DO_ADMA1) {
516 val &= ~SDHCI_CAN_DO_ADMA1;
517 val |= SDHCI_CAN_DO_ADMA2;
518 }
519 }
520
521 if (unlikely(reg == SDHCI_CAPABILITIES_1)) {
522 if (esdhc_is_usdhc(imx_data)) {
523 if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1)
524 val = readl(host->ioaddr + SDHCI_CAPABILITIES) & 0xFFFF;
525 else
526 /* imx6q/dl does not have cap_1 register, fake one */
527 val = SDHCI_SUPPORT_DDR50 | SDHCI_SUPPORT_SDR104
528 | SDHCI_SUPPORT_SDR50
529 | SDHCI_USE_SDR50_TUNING
530 | FIELD_PREP(SDHCI_RETUNING_MODE_MASK,
531 SDHCI_TUNING_MODE_3);
532
533 /*
534 * Do not advertise faster UHS modes if there are no
535 * pinctrl states for 100MHz/200MHz.
536 */
537 if (IS_ERR_OR_NULL(imx_data->pins_100mhz))
538 val &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_DDR50);
539 if (IS_ERR_OR_NULL(imx_data->pins_200mhz))
540 val &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_HS400);
541 }
542 }
543
544 if (unlikely(reg == SDHCI_MAX_CURRENT) && esdhc_is_usdhc(imx_data)) {
545 val = 0;
546 val |= FIELD_PREP(SDHCI_MAX_CURRENT_330_MASK, 0xFF);
547 val |= FIELD_PREP(SDHCI_MAX_CURRENT_300_MASK, 0xFF);
548 val |= FIELD_PREP(SDHCI_MAX_CURRENT_180_MASK, 0xFF);
549 }
550
551 if (unlikely(reg == SDHCI_INT_STATUS)) {
552 if (val & ESDHC_INT_VENDOR_SPEC_DMA_ERR) {
553 val &= ~ESDHC_INT_VENDOR_SPEC_DMA_ERR;
554 val |= SDHCI_INT_ADMA_ERROR;
555 }
556
557 /*
558 * mask off the interrupt we get in response to the manually
559 * sent CMD12
560 */
561 if ((imx_data->multiblock_status == WAIT_FOR_INT) &&
562 ((val & SDHCI_INT_RESPONSE) == SDHCI_INT_RESPONSE)) {
563 val &= ~SDHCI_INT_RESPONSE;
564 writel(SDHCI_INT_RESPONSE, host->ioaddr +
565 SDHCI_INT_STATUS);
566 imx_data->multiblock_status = NO_CMD_PENDING;
567 }
568 }
569
570 return val;
571}
572
573static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg)
574{
575 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
576 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
577 u32 data;
578
579 if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE ||
580 reg == SDHCI_INT_STATUS)) {
581 if ((val & SDHCI_INT_CARD_INT) && !esdhc_is_usdhc(imx_data)) {
582 /*
583 * Clear and then set D3CD bit to avoid missing the
584 * card interrupt. This is an eSDHC controller problem
585 * so we need to apply the following workaround: clear
586 * and set D3CD bit will make eSDHC re-sample the card
587 * interrupt. In case a card interrupt was lost,
588 * re-sample it by the following steps.
589 */
590 data = readl(host->ioaddr + SDHCI_HOST_CONTROL);
591 data &= ~ESDHC_CTRL_D3CD;
592 writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
593 data |= ESDHC_CTRL_D3CD;
594 writel(data, host->ioaddr + SDHCI_HOST_CONTROL);
595 }
596
597 if (val & SDHCI_INT_ADMA_ERROR) {
598 val &= ~SDHCI_INT_ADMA_ERROR;
599 val |= ESDHC_INT_VENDOR_SPEC_DMA_ERR;
600 }
601 }
602
603 if (unlikely((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
604 && (reg == SDHCI_INT_STATUS)
605 && (val & SDHCI_INT_DATA_END))) {
606 u32 v;
607 v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
608 v &= ~ESDHC_VENDOR_SPEC_SDIO_QUIRK;
609 writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
610
611 if (imx_data->multiblock_status == MULTIBLK_IN_PROCESS)
612 {
613 /* send a manual CMD12 with RESPTYP=none */
614 data = MMC_STOP_TRANSMISSION << 24 |
615 SDHCI_CMD_ABORTCMD << 16;
616 writel(data, host->ioaddr + SDHCI_TRANSFER_MODE);
617 imx_data->multiblock_status = WAIT_FOR_INT;
618 }
619 }
620
621 writel(val, host->ioaddr + reg);
622}
623
624static u16 esdhc_readw_le(struct sdhci_host *host, int reg)
625{
626 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
627 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
628 u16 ret = 0;
629 u32 val;
630
631 if (unlikely(reg == SDHCI_HOST_VERSION)) {
632 reg ^= 2;
633 if (esdhc_is_usdhc(imx_data)) {
634 /*
635 * The usdhc register returns a wrong host version.
636 * Correct it here.
637 */
638 return SDHCI_SPEC_300;
639 }
640 }
641
642 if (unlikely(reg == SDHCI_HOST_CONTROL2)) {
643 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
644 if (val & ESDHC_VENDOR_SPEC_VSELECT)
645 ret |= SDHCI_CTRL_VDD_180;
646
647 if (esdhc_is_usdhc(imx_data)) {
648 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING)
649 val = readl(host->ioaddr + ESDHC_MIX_CTRL);
650 else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING)
651 /* the std tuning bits is in ACMD12_ERR for imx6sl */
652 val = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
653 }
654
655 if (val & ESDHC_MIX_CTRL_EXE_TUNE)
656 ret |= SDHCI_CTRL_EXEC_TUNING;
657 if (val & ESDHC_MIX_CTRL_SMPCLK_SEL)
658 ret |= SDHCI_CTRL_TUNED_CLK;
659
660 ret &= ~SDHCI_CTRL_PRESET_VAL_ENABLE;
661
662 return ret;
663 }
664
665 if (unlikely(reg == SDHCI_TRANSFER_MODE)) {
666 if (esdhc_is_usdhc(imx_data)) {
667 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
668 ret = m & ESDHC_MIX_CTRL_SDHCI_MASK;
669 /* Swap AC23 bit */
670 if (m & ESDHC_MIX_CTRL_AC23EN) {
671 ret &= ~ESDHC_MIX_CTRL_AC23EN;
672 ret |= SDHCI_TRNS_AUTO_CMD23;
673 }
674 } else {
675 ret = readw(host->ioaddr + SDHCI_TRANSFER_MODE);
676 }
677
678 return ret;
679 }
680
681 return readw(host->ioaddr + reg);
682}
683
684static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
685{
686 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
687 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
688 u32 new_val = 0;
689
690 switch (reg) {
691 case SDHCI_CLOCK_CONTROL:
692 new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
693 if (val & SDHCI_CLOCK_CARD_EN)
694 new_val |= ESDHC_VENDOR_SPEC_FRC_SDCLK_ON;
695 else
696 new_val &= ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON;
697 writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC);
698 if (!(new_val & ESDHC_VENDOR_SPEC_FRC_SDCLK_ON))
699 esdhc_wait_for_card_clock_gate_off(host);
700 return;
701 case SDHCI_HOST_CONTROL2:
702 new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
703 if (val & SDHCI_CTRL_VDD_180)
704 new_val |= ESDHC_VENDOR_SPEC_VSELECT;
705 else
706 new_val &= ~ESDHC_VENDOR_SPEC_VSELECT;
707 writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC);
708 if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
709 u32 v = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
710 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
711 if (val & SDHCI_CTRL_TUNED_CLK) {
712 v |= ESDHC_MIX_CTRL_SMPCLK_SEL;
713 } else {
714 v &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
715 m &= ~ESDHC_MIX_CTRL_FBCLK_SEL;
716 }
717
718 if (val & SDHCI_CTRL_EXEC_TUNING) {
719 v |= ESDHC_MIX_CTRL_EXE_TUNE;
720 m |= ESDHC_MIX_CTRL_FBCLK_SEL;
721 } else {
722 v &= ~ESDHC_MIX_CTRL_EXE_TUNE;
723 }
724
725 writel(v, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
726 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
727 }
728 return;
729 case SDHCI_TRANSFER_MODE:
730 if ((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT)
731 && (host->cmd->opcode == SD_IO_RW_EXTENDED)
732 && (host->cmd->data->blocks > 1)
733 && (host->cmd->data->flags & MMC_DATA_READ)) {
734 u32 v;
735 v = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
736 v |= ESDHC_VENDOR_SPEC_SDIO_QUIRK;
737 writel(v, host->ioaddr + ESDHC_VENDOR_SPEC);
738 }
739
740 if (esdhc_is_usdhc(imx_data)) {
741 u32 wml;
742 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
743 /* Swap AC23 bit */
744 if (val & SDHCI_TRNS_AUTO_CMD23) {
745 val &= ~SDHCI_TRNS_AUTO_CMD23;
746 val |= ESDHC_MIX_CTRL_AC23EN;
747 }
748 m = val | (m & ~ESDHC_MIX_CTRL_SDHCI_MASK);
749 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
750
751 /* Set watermark levels for PIO access to maximum value
752 * (128 words) to accommodate full 512 bytes buffer.
753 * For DMA access restore the levels to default value.
754 */
755 m = readl(host->ioaddr + ESDHC_WTMK_LVL);
756 if (val & SDHCI_TRNS_DMA) {
757 wml = ESDHC_WTMK_LVL_WML_VAL_DEF;
758 } else {
759 u8 ctrl;
760 wml = ESDHC_WTMK_LVL_WML_VAL_MAX;
761
762 /*
763 * Since already disable DMA mode, so also need
764 * to clear the DMASEL. Otherwise, for standard
765 * tuning, when send tuning command, usdhc will
766 * still prefetch the ADMA script from wrong
767 * DMA address, then we will see IOMMU report
768 * some error which show lack of TLB mapping.
769 */
770 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
771 ctrl &= ~SDHCI_CTRL_DMA_MASK;
772 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
773 }
774 m &= ~(ESDHC_WTMK_LVL_RD_WML_MASK |
775 ESDHC_WTMK_LVL_WR_WML_MASK);
776 m |= (wml << ESDHC_WTMK_LVL_RD_WML_SHIFT) |
777 (wml << ESDHC_WTMK_LVL_WR_WML_SHIFT);
778 writel(m, host->ioaddr + ESDHC_WTMK_LVL);
779 } else {
780 /*
781 * Postpone this write, we must do it together with a
782 * command write that is down below.
783 */
784 imx_data->scratchpad = val;
785 }
786 return;
787 case SDHCI_COMMAND:
788 if (host->cmd->opcode == MMC_STOP_TRANSMISSION)
789 val |= SDHCI_CMD_ABORTCMD;
790
791 if ((host->cmd->opcode == MMC_SET_BLOCK_COUNT) &&
792 (imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
793 imx_data->multiblock_status = MULTIBLK_IN_PROCESS;
794
795 if (esdhc_is_usdhc(imx_data))
796 writel(val << 16,
797 host->ioaddr + SDHCI_TRANSFER_MODE);
798 else
799 writel(val << 16 | imx_data->scratchpad,
800 host->ioaddr + SDHCI_TRANSFER_MODE);
801 return;
802 case SDHCI_BLOCK_SIZE:
803 val &= ~SDHCI_MAKE_BLKSZ(0x7, 0);
804 break;
805 }
806 esdhc_clrset_le(host, 0xffff, val, reg);
807}
808
809static u8 esdhc_readb_le(struct sdhci_host *host, int reg)
810{
811 u8 ret;
812 u32 val;
813
814 switch (reg) {
815 case SDHCI_HOST_CONTROL:
816 val = readl(host->ioaddr + reg);
817
818 ret = val & SDHCI_CTRL_LED;
819 ret |= (val >> 5) & SDHCI_CTRL_DMA_MASK;
820 ret |= (val & ESDHC_CTRL_4BITBUS);
821 ret |= (val & ESDHC_CTRL_8BITBUS) << 3;
822 return ret;
823 }
824
825 return readb(host->ioaddr + reg);
826}
827
828static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg)
829{
830 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
831 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
832 u32 new_val = 0;
833 u32 mask;
834
835 switch (reg) {
836 case SDHCI_POWER_CONTROL:
837 /*
838 * FSL put some DMA bits here
839 * If your board has a regulator, code should be here
840 */
841 return;
842 case SDHCI_HOST_CONTROL:
843 /* FSL messed up here, so we need to manually compose it. */
844 new_val = val & SDHCI_CTRL_LED;
845 /* ensure the endianness */
846 new_val |= ESDHC_HOST_CONTROL_LE;
847 /* bits 8&9 are reserved on mx25 */
848 if (!is_imx25_esdhc(imx_data)) {
849 /* DMA mode bits are shifted */
850 new_val |= (val & SDHCI_CTRL_DMA_MASK) << 5;
851 }
852
853 /*
854 * Do not touch buswidth bits here. This is done in
855 * esdhc_pltfm_bus_width.
856 * Do not touch the D3CD bit either which is used for the
857 * SDIO interrupt erratum workaround.
858 */
859 mask = 0xffff & ~(ESDHC_CTRL_BUSWIDTH_MASK | ESDHC_CTRL_D3CD);
860
861 esdhc_clrset_le(host, mask, new_val, reg);
862 return;
863 case SDHCI_SOFTWARE_RESET:
864 if (val & SDHCI_RESET_DATA)
865 new_val = readl(host->ioaddr + SDHCI_HOST_CONTROL);
866 break;
867 }
868 esdhc_clrset_le(host, 0xff, val, reg);
869
870 if (reg == SDHCI_SOFTWARE_RESET) {
871 if (val & SDHCI_RESET_ALL) {
872 /*
873 * The esdhc has a design violation to SDHC spec which
874 * tells that software reset should not affect card
875 * detection circuit. But esdhc clears its SYSCTL
876 * register bits [0..2] during the software reset. This
877 * will stop those clocks that card detection circuit
878 * relies on. To work around it, we turn the clocks on
879 * back to keep card detection circuit functional.
880 */
881 esdhc_clrset_le(host, 0x7, 0x7, ESDHC_SYSTEM_CONTROL);
882 /*
883 * The reset on usdhc fails to clear MIX_CTRL register.
884 * Do it manually here.
885 */
886 if (esdhc_is_usdhc(imx_data)) {
887 /*
888 * the tuning bits should be kept during reset
889 */
890 new_val = readl(host->ioaddr + ESDHC_MIX_CTRL);
891 writel(new_val & ESDHC_MIX_CTRL_TUNING_MASK,
892 host->ioaddr + ESDHC_MIX_CTRL);
893 imx_data->is_ddr = 0;
894 }
895 } else if (val & SDHCI_RESET_DATA) {
896 /*
897 * The eSDHC DAT line software reset clears at least the
898 * data transfer width on i.MX25, so make sure that the
899 * Host Control register is unaffected.
900 */
901 esdhc_clrset_le(host, 0xff, new_val,
902 SDHCI_HOST_CONTROL);
903 }
904 }
905}
906
907static unsigned int esdhc_pltfm_get_max_clock(struct sdhci_host *host)
908{
909 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
910
911 return pltfm_host->clock;
912}
913
914static unsigned int esdhc_pltfm_get_min_clock(struct sdhci_host *host)
915{
916 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
917
918 return pltfm_host->clock / 256 / 16;
919}
920
921static inline void esdhc_pltfm_set_clock(struct sdhci_host *host,
922 unsigned int clock)
923{
924 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
925 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
926 unsigned int host_clock = pltfm_host->clock;
927 int ddr_pre_div = imx_data->is_ddr ? 2 : 1;
928 int pre_div = 1;
929 int div = 1;
930 int ret;
931 u32 temp, val;
932
933 if (esdhc_is_usdhc(imx_data)) {
934 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
935 writel(val & ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
936 host->ioaddr + ESDHC_VENDOR_SPEC);
937 esdhc_wait_for_card_clock_gate_off(host);
938 }
939
940 if (clock == 0) {
941 host->mmc->actual_clock = 0;
942 return;
943 }
944
945 /* For i.MX53 eSDHCv3, SYSCTL.SDCLKFS may not be set to 0. */
946 if (is_imx53_esdhc(imx_data)) {
947 /*
948 * According to the i.MX53 reference manual, if DLLCTRL[10] can
949 * be set, then the controller is eSDHCv3, else it is eSDHCv2.
950 */
951 val = readl(host->ioaddr + ESDHC_DLL_CTRL);
952 writel(val | BIT(10), host->ioaddr + ESDHC_DLL_CTRL);
953 temp = readl(host->ioaddr + ESDHC_DLL_CTRL);
954 writel(val, host->ioaddr + ESDHC_DLL_CTRL);
955 if (temp & BIT(10))
956 pre_div = 2;
957 }
958
959 temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
960 temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
961 | ESDHC_CLOCK_MASK);
962 sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
963
964 if ((imx_data->socdata->flags & ESDHC_FLAG_ERR010450) &&
965 (!(host->quirks2 & SDHCI_QUIRK2_NO_1_8_V))) {
966 unsigned int max_clock;
967
968 max_clock = imx_data->is_ddr ? 45000000 : 150000000;
969
970 clock = min(clock, max_clock);
971 }
972
973 while (host_clock / (16 * pre_div * ddr_pre_div) > clock &&
974 pre_div < 256)
975 pre_div *= 2;
976
977 while (host_clock / (div * pre_div * ddr_pre_div) > clock && div < 16)
978 div++;
979
980 host->mmc->actual_clock = host_clock / (div * pre_div * ddr_pre_div);
981 dev_dbg(mmc_dev(host->mmc), "desired SD clock: %d, actual: %d\n",
982 clock, host->mmc->actual_clock);
983
984 pre_div >>= 1;
985 div--;
986
987 temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
988 temp |= (ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
989 | (div << ESDHC_DIVIDER_SHIFT)
990 | (pre_div << ESDHC_PREDIV_SHIFT));
991 sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
992
993 /* need to wait the bit 3 of the PRSSTAT to be set, make sure card clock is stable */
994 ret = readl_poll_timeout(host->ioaddr + ESDHC_PRSSTAT, temp,
995 (temp & ESDHC_CLOCK_STABLE), 2, 100);
996 if (ret == -ETIMEDOUT)
997 dev_warn(mmc_dev(host->mmc), "card clock still not stable in 100us!.\n");
998
999 if (esdhc_is_usdhc(imx_data)) {
1000 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC);
1001 writel(val | ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
1002 host->ioaddr + ESDHC_VENDOR_SPEC);
1003 }
1004
1005}
1006
1007static unsigned int esdhc_pltfm_get_ro(struct sdhci_host *host)
1008{
1009 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1010 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1011 struct esdhc_platform_data *boarddata = &imx_data->boarddata;
1012
1013 switch (boarddata->wp_type) {
1014 case ESDHC_WP_GPIO:
1015 return mmc_gpio_get_ro(host->mmc);
1016 case ESDHC_WP_CONTROLLER:
1017 return !(readl(host->ioaddr + SDHCI_PRESENT_STATE) &
1018 SDHCI_WRITE_PROTECT);
1019 case ESDHC_WP_NONE:
1020 break;
1021 }
1022
1023 return -ENOSYS;
1024}
1025
1026static void esdhc_pltfm_set_bus_width(struct sdhci_host *host, int width)
1027{
1028 u32 ctrl;
1029
1030 switch (width) {
1031 case MMC_BUS_WIDTH_8:
1032 ctrl = ESDHC_CTRL_8BITBUS;
1033 break;
1034 case MMC_BUS_WIDTH_4:
1035 ctrl = ESDHC_CTRL_4BITBUS;
1036 break;
1037 default:
1038 ctrl = 0;
1039 break;
1040 }
1041
1042 esdhc_clrset_le(host, ESDHC_CTRL_BUSWIDTH_MASK, ctrl,
1043 SDHCI_HOST_CONTROL);
1044}
1045
1046static void esdhc_reset_tuning(struct sdhci_host *host)
1047{
1048 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1049 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1050 u32 ctrl;
1051 int ret;
1052
1053 /* Reset the tuning circuit */
1054 if (esdhc_is_usdhc(imx_data)) {
1055 ctrl = readl(host->ioaddr + ESDHC_MIX_CTRL);
1056 ctrl &= ~ESDHC_MIX_CTRL_AUTO_TUNE_EN;
1057 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) {
1058 ctrl &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
1059 ctrl &= ~ESDHC_MIX_CTRL_FBCLK_SEL;
1060 writel(ctrl, host->ioaddr + ESDHC_MIX_CTRL);
1061 writel(0, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
1062 } else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
1063 writel(ctrl, host->ioaddr + ESDHC_MIX_CTRL);
1064 ctrl = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS);
1065 ctrl &= ~ESDHC_MIX_CTRL_SMPCLK_SEL;
1066 ctrl &= ~ESDHC_MIX_CTRL_EXE_TUNE;
1067 writel(ctrl, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
1068 /* Make sure ESDHC_MIX_CTRL_EXE_TUNE cleared */
1069 ret = readl_poll_timeout(host->ioaddr + SDHCI_AUTO_CMD_STATUS,
1070 ctrl, !(ctrl & ESDHC_MIX_CTRL_EXE_TUNE), 1, 50);
1071 if (ret == -ETIMEDOUT)
1072 dev_warn(mmc_dev(host->mmc),
1073 "Warning! clear execute tuning bit failed\n");
1074 /*
1075 * SDHCI_INT_DATA_AVAIL is W1C bit, set this bit will clear the
1076 * usdhc IP internal logic flag execute_tuning_with_clr_buf, which
1077 * will finally make sure the normal data transfer logic correct.
1078 */
1079 ctrl = readl(host->ioaddr + SDHCI_INT_STATUS);
1080 ctrl |= SDHCI_INT_DATA_AVAIL;
1081 writel(ctrl, host->ioaddr + SDHCI_INT_STATUS);
1082 }
1083 }
1084}
1085
1086static void usdhc_init_card(struct mmc_host *mmc, struct mmc_card *card)
1087{
1088 struct sdhci_host *host = mmc_priv(mmc);
1089 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1090 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1091
1092 imx_data->init_card_type = card->type;
1093}
1094
1095static int usdhc_execute_tuning(struct mmc_host *mmc, u32 opcode)
1096{
1097 struct sdhci_host *host = mmc_priv(mmc);
1098 int err;
1099
1100 /*
1101 * i.MX uSDHC internally already uses a fixed optimized timing for
1102 * DDR50, normally does not require tuning for DDR50 mode.
1103 */
1104 if (host->timing == MMC_TIMING_UHS_DDR50)
1105 return 0;
1106
1107 /*
1108 * Reset tuning circuit logic. If not, the previous tuning result
1109 * will impact current tuning, make current tuning can't set the
1110 * correct delay cell.
1111 */
1112 esdhc_reset_tuning(host);
1113 err = sdhci_execute_tuning(mmc, opcode);
1114 /* If tuning done, enable auto tuning */
1115 if (!err && !host->tuning_err)
1116 usdhc_auto_tuning_mode_sel_and_en(host);
1117
1118 return err;
1119}
1120
1121static void esdhc_prepare_tuning(struct sdhci_host *host, u32 val)
1122{
1123 u32 reg;
1124 u8 sw_rst;
1125 int ret;
1126
1127 /* FIXME: delay a bit for card to be ready for next tuning due to errors */
1128 mdelay(1);
1129
1130 /* IC suggest to reset USDHC before every tuning command */
1131 esdhc_clrset_le(host, 0xff, SDHCI_RESET_ALL, SDHCI_SOFTWARE_RESET);
1132 ret = readb_poll_timeout(host->ioaddr + SDHCI_SOFTWARE_RESET, sw_rst,
1133 !(sw_rst & SDHCI_RESET_ALL), 10, 100);
1134 if (ret == -ETIMEDOUT)
1135 dev_warn(mmc_dev(host->mmc),
1136 "warning! RESET_ALL never complete before sending tuning command\n");
1137
1138 reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
1139 reg |= ESDHC_MIX_CTRL_EXE_TUNE | ESDHC_MIX_CTRL_SMPCLK_SEL |
1140 ESDHC_MIX_CTRL_FBCLK_SEL;
1141 writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
1142 writel(val << 8, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
1143 dev_dbg(mmc_dev(host->mmc),
1144 "tuning with delay 0x%x ESDHC_TUNE_CTRL_STATUS 0x%x\n",
1145 val, readl(host->ioaddr + ESDHC_TUNE_CTRL_STATUS));
1146}
1147
1148static void esdhc_post_tuning(struct sdhci_host *host)
1149{
1150 u32 reg;
1151
1152 reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
1153 reg &= ~ESDHC_MIX_CTRL_EXE_TUNE;
1154 writel(reg, host->ioaddr + ESDHC_MIX_CTRL);
1155}
1156
1157/*
1158 * find the largest pass window, and use the average delay of this
1159 * largest window to get the best timing.
1160 */
1161static int esdhc_executing_tuning(struct sdhci_host *host, u32 opcode)
1162{
1163 int min, max, avg, ret;
1164 int win_length, target_min, target_max, target_win_length;
1165
1166 min = ESDHC_TUNE_CTRL_MIN;
1167 max = ESDHC_TUNE_CTRL_MIN;
1168 target_win_length = 0;
1169 while (max < ESDHC_TUNE_CTRL_MAX) {
1170 /* find the mininum delay first which can pass tuning */
1171 while (min < ESDHC_TUNE_CTRL_MAX) {
1172 esdhc_prepare_tuning(host, min);
1173 if (!mmc_send_tuning(host->mmc, opcode, NULL))
1174 break;
1175 min += ESDHC_TUNE_CTRL_STEP;
1176 }
1177
1178 /* find the maxinum delay which can not pass tuning */
1179 max = min + ESDHC_TUNE_CTRL_STEP;
1180 while (max < ESDHC_TUNE_CTRL_MAX) {
1181 esdhc_prepare_tuning(host, max);
1182 if (mmc_send_tuning(host->mmc, opcode, NULL)) {
1183 max -= ESDHC_TUNE_CTRL_STEP;
1184 break;
1185 }
1186 max += ESDHC_TUNE_CTRL_STEP;
1187 }
1188
1189 win_length = max - min + 1;
1190 /* get the largest pass window */
1191 if (win_length > target_win_length) {
1192 target_win_length = win_length;
1193 target_min = min;
1194 target_max = max;
1195 }
1196
1197 /* continue to find the next pass window */
1198 min = max + ESDHC_TUNE_CTRL_STEP;
1199 }
1200
1201 /* use average delay to get the best timing */
1202 avg = (target_min + target_max) / 2;
1203 esdhc_prepare_tuning(host, avg);
1204 ret = mmc_send_tuning(host->mmc, opcode, NULL);
1205 esdhc_post_tuning(host);
1206
1207 dev_dbg(mmc_dev(host->mmc), "tuning %s at 0x%x ret %d\n",
1208 ret ? "failed" : "passed", avg, ret);
1209
1210 return ret;
1211}
1212
1213static void esdhc_hs400_enhanced_strobe(struct mmc_host *mmc, struct mmc_ios *ios)
1214{
1215 struct sdhci_host *host = mmc_priv(mmc);
1216 u32 m;
1217
1218 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
1219 if (ios->enhanced_strobe)
1220 m |= ESDHC_MIX_CTRL_HS400_ES_EN;
1221 else
1222 m &= ~ESDHC_MIX_CTRL_HS400_ES_EN;
1223 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1224}
1225
1226static int esdhc_change_pinstate(struct sdhci_host *host,
1227 unsigned int uhs)
1228{
1229 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1230 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1231 struct pinctrl_state *pinctrl;
1232
1233 dev_dbg(mmc_dev(host->mmc), "change pinctrl state for uhs %d\n", uhs);
1234
1235 if (IS_ERR(imx_data->pinctrl) ||
1236 IS_ERR(imx_data->pins_100mhz) ||
1237 IS_ERR(imx_data->pins_200mhz))
1238 return -EINVAL;
1239
1240 switch (uhs) {
1241 case MMC_TIMING_UHS_SDR50:
1242 case MMC_TIMING_UHS_DDR50:
1243 pinctrl = imx_data->pins_100mhz;
1244 break;
1245 case MMC_TIMING_UHS_SDR104:
1246 case MMC_TIMING_MMC_HS200:
1247 case MMC_TIMING_MMC_HS400:
1248 pinctrl = imx_data->pins_200mhz;
1249 break;
1250 default:
1251 /* back to default state for other legacy timing */
1252 return pinctrl_select_default_state(mmc_dev(host->mmc));
1253 }
1254
1255 return pinctrl_select_state(imx_data->pinctrl, pinctrl);
1256}
1257
1258/*
1259 * For HS400 eMMC, there is a data_strobe line. This signal is generated
1260 * by the device and used for data output and CRC status response output
1261 * in HS400 mode. The frequency of this signal follows the frequency of
1262 * CLK generated by host. The host receives the data which is aligned to the
1263 * edge of data_strobe line. Due to the time delay between CLK line and
1264 * data_strobe line, if the delay time is larger than one clock cycle,
1265 * then CLK and data_strobe line will be misaligned, read error shows up.
1266 */
1267static void esdhc_set_strobe_dll(struct sdhci_host *host)
1268{
1269 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1270 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1271 u32 strobe_delay;
1272 u32 v;
1273 int ret;
1274
1275 /* disable clock before enabling strobe dll */
1276 writel(readl(host->ioaddr + ESDHC_VENDOR_SPEC) &
1277 ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON,
1278 host->ioaddr + ESDHC_VENDOR_SPEC);
1279 esdhc_wait_for_card_clock_gate_off(host);
1280
1281 /* force a reset on strobe dll */
1282 writel(ESDHC_STROBE_DLL_CTRL_RESET,
1283 host->ioaddr + ESDHC_STROBE_DLL_CTRL);
1284 /* clear the reset bit on strobe dll before any setting */
1285 writel(0, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
1286
1287 /*
1288 * enable strobe dll ctrl and adjust the delay target
1289 * for the uSDHC loopback read clock
1290 */
1291 if (imx_data->boarddata.strobe_dll_delay_target)
1292 strobe_delay = imx_data->boarddata.strobe_dll_delay_target;
1293 else
1294 strobe_delay = ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT;
1295 v = ESDHC_STROBE_DLL_CTRL_ENABLE |
1296 ESDHC_STROBE_DLL_CTRL_SLV_UPDATE_INT_DEFAULT |
1297 (strobe_delay << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT);
1298 writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
1299
1300 /* wait max 50us to get the REF/SLV lock */
1301 ret = readl_poll_timeout(host->ioaddr + ESDHC_STROBE_DLL_STATUS, v,
1302 ((v & ESDHC_STROBE_DLL_STS_REF_LOCK) && (v & ESDHC_STROBE_DLL_STS_SLV_LOCK)), 1, 50);
1303 if (ret == -ETIMEDOUT)
1304 dev_warn(mmc_dev(host->mmc),
1305 "warning! HS400 strobe DLL status REF/SLV not lock in 50us, STROBE DLL status is %x!\n", v);
1306}
1307
1308static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
1309{
1310 u32 m;
1311 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1312 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1313 struct esdhc_platform_data *boarddata = &imx_data->boarddata;
1314
1315 /* disable ddr mode and disable HS400 mode */
1316 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
1317 m &= ~(ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN);
1318 imx_data->is_ddr = 0;
1319
1320 switch (timing) {
1321 case MMC_TIMING_UHS_SDR12:
1322 case MMC_TIMING_UHS_SDR25:
1323 case MMC_TIMING_UHS_SDR50:
1324 case MMC_TIMING_UHS_SDR104:
1325 case MMC_TIMING_MMC_HS:
1326 case MMC_TIMING_MMC_HS200:
1327 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1328 break;
1329 case MMC_TIMING_UHS_DDR50:
1330 case MMC_TIMING_MMC_DDR52:
1331 m |= ESDHC_MIX_CTRL_DDREN;
1332 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1333 imx_data->is_ddr = 1;
1334 if (boarddata->delay_line) {
1335 u32 v;
1336 v = boarddata->delay_line <<
1337 ESDHC_DLL_OVERRIDE_VAL_SHIFT |
1338 (1 << ESDHC_DLL_OVERRIDE_EN_SHIFT);
1339 if (is_imx53_esdhc(imx_data))
1340 v <<= 1;
1341 writel(v, host->ioaddr + ESDHC_DLL_CTRL);
1342 }
1343 break;
1344 case MMC_TIMING_MMC_HS400:
1345 m |= ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN;
1346 writel(m, host->ioaddr + ESDHC_MIX_CTRL);
1347 imx_data->is_ddr = 1;
1348 /* update clock after enable DDR for strobe DLL lock */
1349 host->ops->set_clock(host, host->clock);
1350 esdhc_set_strobe_dll(host);
1351 break;
1352 case MMC_TIMING_LEGACY:
1353 default:
1354 esdhc_reset_tuning(host);
1355 break;
1356 }
1357
1358 esdhc_change_pinstate(host, timing);
1359}
1360
1361static void esdhc_reset(struct sdhci_host *host, u8 mask)
1362{
1363 sdhci_and_cqhci_reset(host, mask);
1364
1365 sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
1366 sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
1367}
1368
1369static unsigned int esdhc_get_max_timeout_count(struct sdhci_host *host)
1370{
1371 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1372 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1373
1374 /* Doc Erratum: the uSDHC actual maximum timeout count is 1 << 29 */
1375 return esdhc_is_usdhc(imx_data) ? 1 << 29 : 1 << 27;
1376}
1377
1378static void esdhc_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
1379{
1380 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1381 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1382
1383 /* use maximum timeout counter */
1384 esdhc_clrset_le(host, ESDHC_SYS_CTRL_DTOCV_MASK,
1385 esdhc_is_usdhc(imx_data) ? 0xF : 0xE,
1386 SDHCI_TIMEOUT_CONTROL);
1387}
1388
1389static u32 esdhc_cqhci_irq(struct sdhci_host *host, u32 intmask)
1390{
1391 int cmd_error = 0;
1392 int data_error = 0;
1393
1394 if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error))
1395 return intmask;
1396
1397 cqhci_irq(host->mmc, intmask, cmd_error, data_error);
1398
1399 return 0;
1400}
1401
1402static struct sdhci_ops sdhci_esdhc_ops = {
1403 .read_l = esdhc_readl_le,
1404 .read_w = esdhc_readw_le,
1405 .read_b = esdhc_readb_le,
1406 .write_l = esdhc_writel_le,
1407 .write_w = esdhc_writew_le,
1408 .write_b = esdhc_writeb_le,
1409 .set_clock = esdhc_pltfm_set_clock,
1410 .get_max_clock = esdhc_pltfm_get_max_clock,
1411 .get_min_clock = esdhc_pltfm_get_min_clock,
1412 .get_max_timeout_count = esdhc_get_max_timeout_count,
1413 .get_ro = esdhc_pltfm_get_ro,
1414 .set_timeout = esdhc_set_timeout,
1415 .set_bus_width = esdhc_pltfm_set_bus_width,
1416 .set_uhs_signaling = esdhc_set_uhs_signaling,
1417 .reset = esdhc_reset,
1418 .irq = esdhc_cqhci_irq,
1419 .dump_vendor_regs = esdhc_dump_debug_regs,
1420};
1421
1422static const struct sdhci_pltfm_data sdhci_esdhc_imx_pdata = {
1423 .quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_NO_HISPD_BIT
1424 | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
1425 | SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC
1426 | SDHCI_QUIRK_BROKEN_CARD_DETECTION,
1427 .ops = &sdhci_esdhc_ops,
1428};
1429
1430static void sdhci_esdhc_imx_hwinit(struct sdhci_host *host)
1431{
1432 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1433 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1434 struct cqhci_host *cq_host = host->mmc->cqe_private;
1435 u32 tmp;
1436
1437 if (esdhc_is_usdhc(imx_data)) {
1438 /*
1439 * The imx6q ROM code will change the default watermark
1440 * level setting to something insane. Change it back here.
1441 */
1442 writel(ESDHC_WTMK_DEFAULT_VAL, host->ioaddr + ESDHC_WTMK_LVL);
1443
1444 /*
1445 * ROM code will change the bit burst_length_enable setting
1446 * to zero if this usdhc is chosen to boot system. Change
1447 * it back here, otherwise it will impact the performance a
1448 * lot. This bit is used to enable/disable the burst length
1449 * for the external AHB2AXI bridge. It's useful especially
1450 * for INCR transfer because without burst length indicator,
1451 * the AHB2AXI bridge does not know the burst length in
1452 * advance. And without burst length indicator, AHB INCR
1453 * transfer can only be converted to singles on the AXI side.
1454 */
1455 writel(readl(host->ioaddr + SDHCI_HOST_CONTROL)
1456 | ESDHC_BURST_LEN_EN_INCR,
1457 host->ioaddr + SDHCI_HOST_CONTROL);
1458
1459 /*
1460 * erratum ESDHC_FLAG_ERR004536 fix for MX6Q TO1.2 and MX6DL
1461 * TO1.1, it's harmless for MX6SL
1462 */
1463 if (!(imx_data->socdata->flags & ESDHC_FLAG_SKIP_ERR004536)) {
1464 writel(readl(host->ioaddr + 0x6c) & ~BIT(7),
1465 host->ioaddr + 0x6c);
1466 }
1467
1468 /* disable DLL_CTRL delay line settings */
1469 writel(0x0, host->ioaddr + ESDHC_DLL_CTRL);
1470
1471 /*
1472 * For the case of command with busy, if set the bit
1473 * ESDHC_VEND_SPEC2_EN_BUSY_IRQ, USDHC will generate a
1474 * transfer complete interrupt when busy is deasserted.
1475 * When CQHCI use DCMD to send a CMD need R1b respons,
1476 * CQHCI require to set ESDHC_VEND_SPEC2_EN_BUSY_IRQ,
1477 * otherwise DCMD will always meet timeout waiting for
1478 * hardware interrupt issue.
1479 */
1480 if (imx_data->socdata->flags & ESDHC_FLAG_CQHCI) {
1481 tmp = readl(host->ioaddr + ESDHC_VEND_SPEC2);
1482 tmp |= ESDHC_VEND_SPEC2_EN_BUSY_IRQ;
1483 writel(tmp, host->ioaddr + ESDHC_VEND_SPEC2);
1484
1485 host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;
1486 }
1487
1488 if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
1489 tmp = readl(host->ioaddr + ESDHC_TUNING_CTRL);
1490 tmp |= ESDHC_STD_TUNING_EN;
1491
1492 /*
1493 * ROM code or bootloader may config the start tap
1494 * and step, unmask them first.
1495 */
1496 tmp &= ~(ESDHC_TUNING_START_TAP_MASK | ESDHC_TUNING_STEP_MASK);
1497 if (imx_data->boarddata.tuning_start_tap)
1498 tmp |= imx_data->boarddata.tuning_start_tap;
1499 else
1500 tmp |= ESDHC_TUNING_START_TAP_DEFAULT;
1501
1502 if (imx_data->boarddata.tuning_step) {
1503 tmp |= imx_data->boarddata.tuning_step
1504 << ESDHC_TUNING_STEP_SHIFT;
1505 } else {
1506 tmp |= ESDHC_TUNING_STEP_DEFAULT
1507 << ESDHC_TUNING_STEP_SHIFT;
1508 }
1509
1510 /* Disable the CMD CRC check for tuning, if not, need to
1511 * add some delay after every tuning command, because
1512 * hardware standard tuning logic will directly go to next
1513 * step once it detect the CMD CRC error, will not wait for
1514 * the card side to finally send out the tuning data, trigger
1515 * the buffer read ready interrupt immediately. If usdhc send
1516 * the next tuning command some eMMC card will stuck, can't
1517 * response, block the tuning procedure or the first command
1518 * after the whole tuning procedure always can't get any response.
1519 */
1520 tmp |= ESDHC_TUNING_CMD_CRC_CHECK_DISABLE;
1521 writel(tmp, host->ioaddr + ESDHC_TUNING_CTRL);
1522 } else if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) {
1523 /*
1524 * ESDHC_STD_TUNING_EN may be configed in bootloader
1525 * or ROM code, so clear this bit here to make sure
1526 * the manual tuning can work.
1527 */
1528 tmp = readl(host->ioaddr + ESDHC_TUNING_CTRL);
1529 tmp &= ~ESDHC_STD_TUNING_EN;
1530 writel(tmp, host->ioaddr + ESDHC_TUNING_CTRL);
1531 }
1532
1533 /*
1534 * On i.MX8MM, we are running Dual Linux OS, with 1st Linux using SD Card
1535 * as rootfs storage, 2nd Linux using eMMC as rootfs storage. We let
1536 * the 1st linux configure power/clock for the 2nd Linux.
1537 *
1538 * When the 2nd Linux is booting into rootfs stage, we let the 1st Linux
1539 * to destroy the 2nd linux, then restart the 2nd linux, we met SDHCI dump.
1540 * After we clear the pending interrupt and halt CQCTL, issue gone.
1541 */
1542 if (cq_host) {
1543 tmp = cqhci_readl(cq_host, CQHCI_IS);
1544 cqhci_writel(cq_host, tmp, CQHCI_IS);
1545 cqhci_writel(cq_host, CQHCI_HALT, CQHCI_CTL);
1546 }
1547 }
1548}
1549
1550static void esdhc_cqe_enable(struct mmc_host *mmc)
1551{
1552 struct sdhci_host *host = mmc_priv(mmc);
1553 struct cqhci_host *cq_host = mmc->cqe_private;
1554 u32 reg;
1555 u16 mode;
1556 int count = 10;
1557
1558 /*
1559 * CQE gets stuck if it sees Buffer Read Enable bit set, which can be
1560 * the case after tuning, so ensure the buffer is drained.
1561 */
1562 reg = sdhci_readl(host, SDHCI_PRESENT_STATE);
1563 while (reg & SDHCI_DATA_AVAILABLE) {
1564 sdhci_readl(host, SDHCI_BUFFER);
1565 reg = sdhci_readl(host, SDHCI_PRESENT_STATE);
1566 if (count-- == 0) {
1567 dev_warn(mmc_dev(host->mmc),
1568 "CQE may get stuck because the Buffer Read Enable bit is set\n");
1569 break;
1570 }
1571 mdelay(1);
1572 }
1573
1574 /*
1575 * Runtime resume will reset the entire host controller, which
1576 * will also clear the DMAEN/BCEN of register ESDHC_MIX_CTRL.
1577 * Here set DMAEN and BCEN when enable CMDQ.
1578 */
1579 mode = sdhci_readw(host, SDHCI_TRANSFER_MODE);
1580 if (host->flags & SDHCI_REQ_USE_DMA)
1581 mode |= SDHCI_TRNS_DMA;
1582 if (!(host->quirks2 & SDHCI_QUIRK2_SUPPORT_SINGLE))
1583 mode |= SDHCI_TRNS_BLK_CNT_EN;
1584 sdhci_writew(host, mode, SDHCI_TRANSFER_MODE);
1585
1586 /*
1587 * Though Runtime resume reset the entire host controller,
1588 * but do not impact the CQHCI side, need to clear the
1589 * HALT bit, avoid CQHCI stuck in the first request when
1590 * system resume back.
1591 */
1592 cqhci_writel(cq_host, 0, CQHCI_CTL);
1593 if (cqhci_readl(cq_host, CQHCI_CTL) & CQHCI_HALT)
1594 dev_err(mmc_dev(host->mmc),
1595 "failed to exit halt state when enable CQE\n");
1596
1597
1598 sdhci_cqe_enable(mmc);
1599}
1600
1601static void esdhc_sdhci_dumpregs(struct mmc_host *mmc)
1602{
1603 sdhci_dumpregs(mmc_priv(mmc));
1604}
1605
1606static const struct cqhci_host_ops esdhc_cqhci_ops = {
1607 .enable = esdhc_cqe_enable,
1608 .disable = sdhci_cqe_disable,
1609 .dumpregs = esdhc_sdhci_dumpregs,
1610};
1611
1612static int
1613sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
1614 struct sdhci_host *host,
1615 struct pltfm_imx_data *imx_data)
1616{
1617 struct device_node *np = pdev->dev.of_node;
1618 struct esdhc_platform_data *boarddata = &imx_data->boarddata;
1619 int ret;
1620
1621 if (of_property_read_bool(np, "fsl,wp-controller"))
1622 boarddata->wp_type = ESDHC_WP_CONTROLLER;
1623
1624 /*
1625 * If we have this property, then activate WP check.
1626 * Retrieveing and requesting the actual WP GPIO will happen
1627 * in the call to mmc_of_parse().
1628 */
1629 if (of_property_read_bool(np, "wp-gpios"))
1630 boarddata->wp_type = ESDHC_WP_GPIO;
1631
1632 of_property_read_u32(np, "fsl,tuning-step", &boarddata->tuning_step);
1633 of_property_read_u32(np, "fsl,tuning-start-tap",
1634 &boarddata->tuning_start_tap);
1635
1636 of_property_read_u32(np, "fsl,strobe-dll-delay-target",
1637 &boarddata->strobe_dll_delay_target);
1638 if (of_property_read_bool(np, "no-1-8-v"))
1639 host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V;
1640
1641 if (of_property_read_u32(np, "fsl,delay-line", &boarddata->delay_line))
1642 boarddata->delay_line = 0;
1643
1644 mmc_of_parse_voltage(host->mmc, &host->ocr_mask);
1645
1646 if (esdhc_is_usdhc(imx_data) && !IS_ERR(imx_data->pinctrl)) {
1647 imx_data->pins_100mhz = pinctrl_lookup_state(imx_data->pinctrl,
1648 ESDHC_PINCTRL_STATE_100MHZ);
1649 imx_data->pins_200mhz = pinctrl_lookup_state(imx_data->pinctrl,
1650 ESDHC_PINCTRL_STATE_200MHZ);
1651 }
1652
1653 /* call to generic mmc_of_parse to support additional capabilities */
1654 ret = mmc_of_parse(host->mmc);
1655 if (ret)
1656 return ret;
1657
1658 /* HS400/HS400ES require 8 bit bus */
1659 if (!(host->mmc->caps & MMC_CAP_8_BIT_DATA))
1660 host->mmc->caps2 &= ~(MMC_CAP2_HS400 | MMC_CAP2_HS400_ES);
1661
1662 if (mmc_gpio_get_cd(host->mmc) >= 0)
1663 host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION;
1664
1665 return 0;
1666}
1667
1668static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
1669{
1670 struct sdhci_pltfm_host *pltfm_host;
1671 struct sdhci_host *host;
1672 struct cqhci_host *cq_host;
1673 int err;
1674 struct pltfm_imx_data *imx_data;
1675
1676 host = sdhci_pltfm_init(pdev, &sdhci_esdhc_imx_pdata,
1677 sizeof(*imx_data));
1678 if (IS_ERR(host))
1679 return PTR_ERR(host);
1680
1681 pltfm_host = sdhci_priv(host);
1682
1683 imx_data = sdhci_pltfm_priv(pltfm_host);
1684
1685 imx_data->socdata = device_get_match_data(&pdev->dev);
1686
1687 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1688 cpu_latency_qos_add_request(&imx_data->pm_qos_req, 0);
1689
1690 imx_data->clk_ipg = devm_clk_get(&pdev->dev, "ipg");
1691 if (IS_ERR(imx_data->clk_ipg)) {
1692 err = PTR_ERR(imx_data->clk_ipg);
1693 goto free_sdhci;
1694 }
1695
1696 imx_data->clk_ahb = devm_clk_get(&pdev->dev, "ahb");
1697 if (IS_ERR(imx_data->clk_ahb)) {
1698 err = PTR_ERR(imx_data->clk_ahb);
1699 goto free_sdhci;
1700 }
1701
1702 imx_data->clk_per = devm_clk_get(&pdev->dev, "per");
1703 if (IS_ERR(imx_data->clk_per)) {
1704 err = PTR_ERR(imx_data->clk_per);
1705 goto free_sdhci;
1706 }
1707
1708 pltfm_host->clk = imx_data->clk_per;
1709 pltfm_host->clock = clk_get_rate(pltfm_host->clk);
1710 err = clk_prepare_enable(imx_data->clk_per);
1711 if (err)
1712 goto free_sdhci;
1713 err = clk_prepare_enable(imx_data->clk_ipg);
1714 if (err)
1715 goto disable_per_clk;
1716 err = clk_prepare_enable(imx_data->clk_ahb);
1717 if (err)
1718 goto disable_ipg_clk;
1719
1720 imx_data->pinctrl = devm_pinctrl_get(&pdev->dev);
1721 if (IS_ERR(imx_data->pinctrl))
1722 dev_warn(mmc_dev(host->mmc), "could not get pinctrl\n");
1723
1724 if (esdhc_is_usdhc(imx_data)) {
1725 host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
1726 host->mmc->caps |= MMC_CAP_1_8V_DDR | MMC_CAP_3_3V_DDR;
1727
1728 /* GPIO CD can be set as a wakeup source */
1729 host->mmc->caps |= MMC_CAP_CD_WAKE;
1730
1731 if (!(imx_data->socdata->flags & ESDHC_FLAG_HS200))
1732 host->quirks2 |= SDHCI_QUIRK2_BROKEN_HS200;
1733
1734 /* clear tuning bits in case ROM has set it already */
1735 writel(0x0, host->ioaddr + ESDHC_MIX_CTRL);
1736 writel(0x0, host->ioaddr + SDHCI_AUTO_CMD_STATUS);
1737 writel(0x0, host->ioaddr + ESDHC_TUNE_CTRL_STATUS);
1738
1739 /*
1740 * Link usdhc specific mmc_host_ops execute_tuning function,
1741 * to replace the standard one in sdhci_ops.
1742 */
1743 host->mmc_host_ops.execute_tuning = usdhc_execute_tuning;
1744
1745 /*
1746 * Link usdhc specific mmc_host_ops init card function,
1747 * to distinguish the card type.
1748 */
1749 host->mmc_host_ops.init_card = usdhc_init_card;
1750 }
1751
1752 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING)
1753 sdhci_esdhc_ops.platform_execute_tuning =
1754 esdhc_executing_tuning;
1755
1756 if (imx_data->socdata->flags & ESDHC_FLAG_ERR004536)
1757 host->quirks |= SDHCI_QUIRK_BROKEN_ADMA;
1758
1759 if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
1760 host->mmc->caps2 |= MMC_CAP2_HS400;
1761
1762 if (imx_data->socdata->flags & ESDHC_FLAG_BROKEN_AUTO_CMD23)
1763 host->quirks2 |= SDHCI_QUIRK2_ACMD23_BROKEN;
1764
1765 if (imx_data->socdata->flags & ESDHC_FLAG_HS400_ES) {
1766 host->mmc->caps2 |= MMC_CAP2_HS400_ES;
1767 host->mmc_host_ops.hs400_enhanced_strobe =
1768 esdhc_hs400_enhanced_strobe;
1769 }
1770
1771 if (imx_data->socdata->flags & ESDHC_FLAG_CQHCI) {
1772 host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD;
1773 cq_host = devm_kzalloc(&pdev->dev, sizeof(*cq_host), GFP_KERNEL);
1774 if (!cq_host) {
1775 err = -ENOMEM;
1776 goto disable_ahb_clk;
1777 }
1778
1779 cq_host->mmio = host->ioaddr + ESDHC_CQHCI_ADDR_OFFSET;
1780 cq_host->ops = &esdhc_cqhci_ops;
1781
1782 err = cqhci_init(cq_host, host->mmc, false);
1783 if (err)
1784 goto disable_ahb_clk;
1785 }
1786
1787 err = sdhci_esdhc_imx_probe_dt(pdev, host, imx_data);
1788 if (err)
1789 goto disable_ahb_clk;
1790
1791 sdhci_esdhc_imx_hwinit(host);
1792
1793 err = sdhci_add_host(host);
1794 if (err)
1795 goto disable_ahb_clk;
1796
1797 /*
1798 * Setup the wakeup capability here, let user to decide
1799 * whether need to enable this wakeup through sysfs interface.
1800 */
1801 if ((host->mmc->pm_caps & MMC_PM_KEEP_POWER) &&
1802 (host->mmc->pm_caps & MMC_PM_WAKE_SDIO_IRQ))
1803 device_set_wakeup_capable(&pdev->dev, true);
1804
1805 pm_runtime_set_active(&pdev->dev);
1806 pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
1807 pm_runtime_use_autosuspend(&pdev->dev);
1808 pm_suspend_ignore_children(&pdev->dev, 1);
1809 pm_runtime_enable(&pdev->dev);
1810
1811 return 0;
1812
1813disable_ahb_clk:
1814 clk_disable_unprepare(imx_data->clk_ahb);
1815disable_ipg_clk:
1816 clk_disable_unprepare(imx_data->clk_ipg);
1817disable_per_clk:
1818 clk_disable_unprepare(imx_data->clk_per);
1819free_sdhci:
1820 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1821 cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1822 sdhci_pltfm_free(pdev);
1823 return err;
1824}
1825
1826static void sdhci_esdhc_imx_remove(struct platform_device *pdev)
1827{
1828 struct sdhci_host *host = platform_get_drvdata(pdev);
1829 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1830 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1831 int dead;
1832
1833 pm_runtime_get_sync(&pdev->dev);
1834 dead = (readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff);
1835 pm_runtime_disable(&pdev->dev);
1836 pm_runtime_put_noidle(&pdev->dev);
1837
1838 sdhci_remove_host(host, dead);
1839
1840 clk_disable_unprepare(imx_data->clk_per);
1841 clk_disable_unprepare(imx_data->clk_ipg);
1842 clk_disable_unprepare(imx_data->clk_ahb);
1843
1844 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1845 cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1846
1847 sdhci_pltfm_free(pdev);
1848}
1849
1850#ifdef CONFIG_PM_SLEEP
1851static int sdhci_esdhc_suspend(struct device *dev)
1852{
1853 struct sdhci_host *host = dev_get_drvdata(dev);
1854 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1855 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1856 int ret;
1857
1858 if (host->mmc->caps2 & MMC_CAP2_CQE) {
1859 ret = cqhci_suspend(host->mmc);
1860 if (ret)
1861 return ret;
1862 }
1863
1864 if ((imx_data->socdata->flags & ESDHC_FLAG_STATE_LOST_IN_LPMODE) &&
1865 (host->tuning_mode != SDHCI_TUNING_MODE_1)) {
1866 mmc_retune_timer_stop(host->mmc);
1867 mmc_retune_needed(host->mmc);
1868 }
1869
1870 if (host->tuning_mode != SDHCI_TUNING_MODE_3)
1871 mmc_retune_needed(host->mmc);
1872
1873 ret = sdhci_suspend_host(host);
1874 if (ret)
1875 return ret;
1876
1877 ret = pinctrl_pm_select_sleep_state(dev);
1878 if (ret)
1879 return ret;
1880
1881 ret = mmc_gpio_set_cd_wake(host->mmc, true);
1882
1883 return ret;
1884}
1885
1886static int sdhci_esdhc_resume(struct device *dev)
1887{
1888 struct sdhci_host *host = dev_get_drvdata(dev);
1889 int ret;
1890
1891 ret = pinctrl_pm_select_default_state(dev);
1892 if (ret)
1893 return ret;
1894
1895 /* re-initialize hw state in case it's lost in low power mode */
1896 sdhci_esdhc_imx_hwinit(host);
1897
1898 ret = sdhci_resume_host(host);
1899 if (ret)
1900 return ret;
1901
1902 if (host->mmc->caps2 & MMC_CAP2_CQE)
1903 ret = cqhci_resume(host->mmc);
1904
1905 if (!ret)
1906 ret = mmc_gpio_set_cd_wake(host->mmc, false);
1907
1908 return ret;
1909}
1910#endif
1911
1912#ifdef CONFIG_PM
1913static int sdhci_esdhc_runtime_suspend(struct device *dev)
1914{
1915 struct sdhci_host *host = dev_get_drvdata(dev);
1916 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1917 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1918 int ret;
1919
1920 if (host->mmc->caps2 & MMC_CAP2_CQE) {
1921 ret = cqhci_suspend(host->mmc);
1922 if (ret)
1923 return ret;
1924 }
1925
1926 ret = sdhci_runtime_suspend_host(host);
1927 if (ret)
1928 return ret;
1929
1930 if (host->tuning_mode != SDHCI_TUNING_MODE_3)
1931 mmc_retune_needed(host->mmc);
1932
1933 imx_data->actual_clock = host->mmc->actual_clock;
1934 esdhc_pltfm_set_clock(host, 0);
1935 clk_disable_unprepare(imx_data->clk_per);
1936 clk_disable_unprepare(imx_data->clk_ipg);
1937 clk_disable_unprepare(imx_data->clk_ahb);
1938
1939 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1940 cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1941
1942 return ret;
1943}
1944
1945static int sdhci_esdhc_runtime_resume(struct device *dev)
1946{
1947 struct sdhci_host *host = dev_get_drvdata(dev);
1948 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1949 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
1950 int err;
1951
1952 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1953 cpu_latency_qos_add_request(&imx_data->pm_qos_req, 0);
1954
1955 if (imx_data->socdata->flags & ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME)
1956 clk_set_rate(imx_data->clk_per, pltfm_host->clock);
1957
1958 err = clk_prepare_enable(imx_data->clk_ahb);
1959 if (err)
1960 goto remove_pm_qos_request;
1961
1962 err = clk_prepare_enable(imx_data->clk_per);
1963 if (err)
1964 goto disable_ahb_clk;
1965
1966 err = clk_prepare_enable(imx_data->clk_ipg);
1967 if (err)
1968 goto disable_per_clk;
1969
1970 esdhc_pltfm_set_clock(host, imx_data->actual_clock);
1971
1972 err = sdhci_runtime_resume_host(host, 0);
1973 if (err)
1974 goto disable_ipg_clk;
1975
1976 if (host->mmc->caps2 & MMC_CAP2_CQE)
1977 err = cqhci_resume(host->mmc);
1978
1979 return err;
1980
1981disable_ipg_clk:
1982 clk_disable_unprepare(imx_data->clk_ipg);
1983disable_per_clk:
1984 clk_disable_unprepare(imx_data->clk_per);
1985disable_ahb_clk:
1986 clk_disable_unprepare(imx_data->clk_ahb);
1987remove_pm_qos_request:
1988 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS)
1989 cpu_latency_qos_remove_request(&imx_data->pm_qos_req);
1990 return err;
1991}
1992#endif
1993
1994static const struct dev_pm_ops sdhci_esdhc_pmops = {
1995 SET_SYSTEM_SLEEP_PM_OPS(sdhci_esdhc_suspend, sdhci_esdhc_resume)
1996 SET_RUNTIME_PM_OPS(sdhci_esdhc_runtime_suspend,
1997 sdhci_esdhc_runtime_resume, NULL)
1998};
1999
2000static struct platform_driver sdhci_esdhc_imx_driver = {
2001 .driver = {
2002 .name = "sdhci-esdhc-imx",
2003 .probe_type = PROBE_PREFER_ASYNCHRONOUS,
2004 .of_match_table = imx_esdhc_dt_ids,
2005 .pm = &sdhci_esdhc_pmops,
2006 },
2007 .probe = sdhci_esdhc_imx_probe,
2008 .remove_new = sdhci_esdhc_imx_remove,
2009};
2010
2011module_platform_driver(sdhci_esdhc_imx_driver);
2012
2013MODULE_DESCRIPTION("SDHCI driver for Freescale i.MX eSDHC");
2014MODULE_AUTHOR("Wolfram Sang <kernel@pengutronix.de>");
2015MODULE_LICENSE("GPL v2");