Loading...
1/*
2 * linux/drivers/mmc/host/sdhci.c - Secure Digital Host Controller Interface driver
3 *
4 * Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved.
5 *
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License as published by
8 * the Free Software Foundation; either version 2 of the License, or (at
9 * your option) any later version.
10 *
11 * Thanks to the following companies for their support:
12 *
13 * - JMicron (hardware and technical support)
14 */
15
16#include <linux/delay.h>
17#include <linux/highmem.h>
18#include <linux/io.h>
19#include <linux/module.h>
20#include <linux/dma-mapping.h>
21#include <linux/slab.h>
22#include <linux/scatterlist.h>
23#include <linux/regulator/consumer.h>
24#include <linux/pm_runtime.h>
25
26#include <linux/leds.h>
27
28#include <linux/mmc/mmc.h>
29#include <linux/mmc/host.h>
30#include <linux/mmc/card.h>
31#include <linux/mmc/slot-gpio.h>
32
33#include "sdhci.h"
34
35#define DRIVER_NAME "sdhci"
36
37#define DBG(f, x...) \
38 pr_debug(DRIVER_NAME " [%s()]: " f, __func__,## x)
39
40#if defined(CONFIG_LEDS_CLASS) || (defined(CONFIG_LEDS_CLASS_MODULE) && \
41 defined(CONFIG_MMC_SDHCI_MODULE))
42#define SDHCI_USE_LEDS_CLASS
43#endif
44
45#define MAX_TUNING_LOOP 40
46
47static unsigned int debug_quirks = 0;
48static unsigned int debug_quirks2;
49
50static void sdhci_finish_data(struct sdhci_host *);
51
52static void sdhci_finish_command(struct sdhci_host *);
53static int sdhci_execute_tuning(struct mmc_host *mmc, u32 opcode);
54static void sdhci_tuning_timer(unsigned long data);
55static void sdhci_enable_preset_value(struct sdhci_host *host, bool enable);
56
57#ifdef CONFIG_PM_RUNTIME
58static int sdhci_runtime_pm_get(struct sdhci_host *host);
59static int sdhci_runtime_pm_put(struct sdhci_host *host);
60static void sdhci_runtime_pm_bus_on(struct sdhci_host *host);
61static void sdhci_runtime_pm_bus_off(struct sdhci_host *host);
62#else
63static inline int sdhci_runtime_pm_get(struct sdhci_host *host)
64{
65 return 0;
66}
67static inline int sdhci_runtime_pm_put(struct sdhci_host *host)
68{
69 return 0;
70}
71static void sdhci_runtime_pm_bus_on(struct sdhci_host *host)
72{
73}
74static void sdhci_runtime_pm_bus_off(struct sdhci_host *host)
75{
76}
77#endif
78
79static void sdhci_dumpregs(struct sdhci_host *host)
80{
81 pr_debug(DRIVER_NAME ": =========== REGISTER DUMP (%s)===========\n",
82 mmc_hostname(host->mmc));
83
84 pr_debug(DRIVER_NAME ": Sys addr: 0x%08x | Version: 0x%08x\n",
85 sdhci_readl(host, SDHCI_DMA_ADDRESS),
86 sdhci_readw(host, SDHCI_HOST_VERSION));
87 pr_debug(DRIVER_NAME ": Blk size: 0x%08x | Blk cnt: 0x%08x\n",
88 sdhci_readw(host, SDHCI_BLOCK_SIZE),
89 sdhci_readw(host, SDHCI_BLOCK_COUNT));
90 pr_debug(DRIVER_NAME ": Argument: 0x%08x | Trn mode: 0x%08x\n",
91 sdhci_readl(host, SDHCI_ARGUMENT),
92 sdhci_readw(host, SDHCI_TRANSFER_MODE));
93 pr_debug(DRIVER_NAME ": Present: 0x%08x | Host ctl: 0x%08x\n",
94 sdhci_readl(host, SDHCI_PRESENT_STATE),
95 sdhci_readb(host, SDHCI_HOST_CONTROL));
96 pr_debug(DRIVER_NAME ": Power: 0x%08x | Blk gap: 0x%08x\n",
97 sdhci_readb(host, SDHCI_POWER_CONTROL),
98 sdhci_readb(host, SDHCI_BLOCK_GAP_CONTROL));
99 pr_debug(DRIVER_NAME ": Wake-up: 0x%08x | Clock: 0x%08x\n",
100 sdhci_readb(host, SDHCI_WAKE_UP_CONTROL),
101 sdhci_readw(host, SDHCI_CLOCK_CONTROL));
102 pr_debug(DRIVER_NAME ": Timeout: 0x%08x | Int stat: 0x%08x\n",
103 sdhci_readb(host, SDHCI_TIMEOUT_CONTROL),
104 sdhci_readl(host, SDHCI_INT_STATUS));
105 pr_debug(DRIVER_NAME ": Int enab: 0x%08x | Sig enab: 0x%08x\n",
106 sdhci_readl(host, SDHCI_INT_ENABLE),
107 sdhci_readl(host, SDHCI_SIGNAL_ENABLE));
108 pr_debug(DRIVER_NAME ": AC12 err: 0x%08x | Slot int: 0x%08x\n",
109 sdhci_readw(host, SDHCI_ACMD12_ERR),
110 sdhci_readw(host, SDHCI_SLOT_INT_STATUS));
111 pr_debug(DRIVER_NAME ": Caps: 0x%08x | Caps_1: 0x%08x\n",
112 sdhci_readl(host, SDHCI_CAPABILITIES),
113 sdhci_readl(host, SDHCI_CAPABILITIES_1));
114 pr_debug(DRIVER_NAME ": Cmd: 0x%08x | Max curr: 0x%08x\n",
115 sdhci_readw(host, SDHCI_COMMAND),
116 sdhci_readl(host, SDHCI_MAX_CURRENT));
117 pr_debug(DRIVER_NAME ": Host ctl2: 0x%08x\n",
118 sdhci_readw(host, SDHCI_HOST_CONTROL2));
119
120 if (host->flags & SDHCI_USE_ADMA)
121 pr_debug(DRIVER_NAME ": ADMA Err: 0x%08x | ADMA Ptr: 0x%08x\n",
122 readl(host->ioaddr + SDHCI_ADMA_ERROR),
123 readl(host->ioaddr + SDHCI_ADMA_ADDRESS));
124
125 pr_debug(DRIVER_NAME ": ===========================================\n");
126}
127
128/*****************************************************************************\
129 * *
130 * Low level functions *
131 * *
132\*****************************************************************************/
133
134static void sdhci_clear_set_irqs(struct sdhci_host *host, u32 clear, u32 set)
135{
136 u32 ier;
137
138 ier = sdhci_readl(host, SDHCI_INT_ENABLE);
139 ier &= ~clear;
140 ier |= set;
141 sdhci_writel(host, ier, SDHCI_INT_ENABLE);
142 sdhci_writel(host, ier, SDHCI_SIGNAL_ENABLE);
143}
144
145static void sdhci_unmask_irqs(struct sdhci_host *host, u32 irqs)
146{
147 sdhci_clear_set_irqs(host, 0, irqs);
148}
149
150static void sdhci_mask_irqs(struct sdhci_host *host, u32 irqs)
151{
152 sdhci_clear_set_irqs(host, irqs, 0);
153}
154
155static void sdhci_set_card_detection(struct sdhci_host *host, bool enable)
156{
157 u32 present, irqs;
158
159 if ((host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) ||
160 (host->mmc->caps & MMC_CAP_NONREMOVABLE))
161 return;
162
163 present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
164 SDHCI_CARD_PRESENT;
165 irqs = present ? SDHCI_INT_CARD_REMOVE : SDHCI_INT_CARD_INSERT;
166
167 if (enable)
168 sdhci_unmask_irqs(host, irqs);
169 else
170 sdhci_mask_irqs(host, irqs);
171}
172
173static void sdhci_enable_card_detection(struct sdhci_host *host)
174{
175 sdhci_set_card_detection(host, true);
176}
177
178static void sdhci_disable_card_detection(struct sdhci_host *host)
179{
180 sdhci_set_card_detection(host, false);
181}
182
183static void sdhci_reset(struct sdhci_host *host, u8 mask)
184{
185 unsigned long timeout;
186 u32 uninitialized_var(ier);
187
188 if (host->quirks & SDHCI_QUIRK_NO_CARD_NO_RESET) {
189 if (!(sdhci_readl(host, SDHCI_PRESENT_STATE) &
190 SDHCI_CARD_PRESENT))
191 return;
192 }
193
194 if (host->quirks & SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET)
195 ier = sdhci_readl(host, SDHCI_INT_ENABLE);
196
197 if (host->ops->platform_reset_enter)
198 host->ops->platform_reset_enter(host, mask);
199
200 sdhci_writeb(host, mask, SDHCI_SOFTWARE_RESET);
201
202 if (mask & SDHCI_RESET_ALL) {
203 host->clock = 0;
204 /* Reset-all turns off SD Bus Power */
205 if (host->quirks2 & SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON)
206 sdhci_runtime_pm_bus_off(host);
207 }
208
209 /* Wait max 100 ms */
210 timeout = 100;
211
212 /* hw clears the bit when it's done */
213 while (sdhci_readb(host, SDHCI_SOFTWARE_RESET) & mask) {
214 if (timeout == 0) {
215 pr_err("%s: Reset 0x%x never completed.\n",
216 mmc_hostname(host->mmc), (int)mask);
217 sdhci_dumpregs(host);
218 return;
219 }
220 timeout--;
221 mdelay(1);
222 }
223
224 if (host->ops->platform_reset_exit)
225 host->ops->platform_reset_exit(host, mask);
226
227 if (host->quirks & SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET)
228 sdhci_clear_set_irqs(host, SDHCI_INT_ALL_MASK, ier);
229
230 if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
231 if ((host->ops->enable_dma) && (mask & SDHCI_RESET_ALL))
232 host->ops->enable_dma(host);
233 }
234}
235
236static void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios);
237
238static void sdhci_init(struct sdhci_host *host, int soft)
239{
240 if (soft)
241 sdhci_reset(host, SDHCI_RESET_CMD|SDHCI_RESET_DATA);
242 else
243 sdhci_reset(host, SDHCI_RESET_ALL);
244
245 sdhci_clear_set_irqs(host, SDHCI_INT_ALL_MASK,
246 SDHCI_INT_BUS_POWER | SDHCI_INT_DATA_END_BIT |
247 SDHCI_INT_DATA_CRC | SDHCI_INT_DATA_TIMEOUT | SDHCI_INT_INDEX |
248 SDHCI_INT_END_BIT | SDHCI_INT_CRC | SDHCI_INT_TIMEOUT |
249 SDHCI_INT_DATA_END | SDHCI_INT_RESPONSE);
250
251 if (soft) {
252 /* force clock reconfiguration */
253 host->clock = 0;
254 sdhci_set_ios(host->mmc, &host->mmc->ios);
255 }
256}
257
258static void sdhci_reinit(struct sdhci_host *host)
259{
260 sdhci_init(host, 0);
261 /*
262 * Retuning stuffs are affected by different cards inserted and only
263 * applicable to UHS-I cards. So reset these fields to their initial
264 * value when card is removed.
265 */
266 if (host->flags & SDHCI_USING_RETUNING_TIMER) {
267 host->flags &= ~SDHCI_USING_RETUNING_TIMER;
268
269 del_timer_sync(&host->tuning_timer);
270 host->flags &= ~SDHCI_NEEDS_RETUNING;
271 host->mmc->max_blk_count =
272 (host->quirks & SDHCI_QUIRK_NO_MULTIBLOCK) ? 1 : 65535;
273 }
274 sdhci_enable_card_detection(host);
275}
276
277static void sdhci_activate_led(struct sdhci_host *host)
278{
279 u8 ctrl;
280
281 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
282 ctrl |= SDHCI_CTRL_LED;
283 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
284}
285
286static void sdhci_deactivate_led(struct sdhci_host *host)
287{
288 u8 ctrl;
289
290 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
291 ctrl &= ~SDHCI_CTRL_LED;
292 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
293}
294
295#ifdef SDHCI_USE_LEDS_CLASS
296static void sdhci_led_control(struct led_classdev *led,
297 enum led_brightness brightness)
298{
299 struct sdhci_host *host = container_of(led, struct sdhci_host, led);
300 unsigned long flags;
301
302 spin_lock_irqsave(&host->lock, flags);
303
304 if (host->runtime_suspended)
305 goto out;
306
307 if (brightness == LED_OFF)
308 sdhci_deactivate_led(host);
309 else
310 sdhci_activate_led(host);
311out:
312 spin_unlock_irqrestore(&host->lock, flags);
313}
314#endif
315
316/*****************************************************************************\
317 * *
318 * Core functions *
319 * *
320\*****************************************************************************/
321
322static void sdhci_read_block_pio(struct sdhci_host *host)
323{
324 unsigned long flags;
325 size_t blksize, len, chunk;
326 u32 uninitialized_var(scratch);
327 u8 *buf;
328
329 DBG("PIO reading\n");
330
331 blksize = host->data->blksz;
332 chunk = 0;
333
334 local_irq_save(flags);
335
336 while (blksize) {
337 if (!sg_miter_next(&host->sg_miter))
338 BUG();
339
340 len = min(host->sg_miter.length, blksize);
341
342 blksize -= len;
343 host->sg_miter.consumed = len;
344
345 buf = host->sg_miter.addr;
346
347 while (len) {
348 if (chunk == 0) {
349 scratch = sdhci_readl(host, SDHCI_BUFFER);
350 chunk = 4;
351 }
352
353 *buf = scratch & 0xFF;
354
355 buf++;
356 scratch >>= 8;
357 chunk--;
358 len--;
359 }
360 }
361
362 sg_miter_stop(&host->sg_miter);
363
364 local_irq_restore(flags);
365}
366
367static void sdhci_write_block_pio(struct sdhci_host *host)
368{
369 unsigned long flags;
370 size_t blksize, len, chunk;
371 u32 scratch;
372 u8 *buf;
373
374 DBG("PIO writing\n");
375
376 blksize = host->data->blksz;
377 chunk = 0;
378 scratch = 0;
379
380 local_irq_save(flags);
381
382 while (blksize) {
383 if (!sg_miter_next(&host->sg_miter))
384 BUG();
385
386 len = min(host->sg_miter.length, blksize);
387
388 blksize -= len;
389 host->sg_miter.consumed = len;
390
391 buf = host->sg_miter.addr;
392
393 while (len) {
394 scratch |= (u32)*buf << (chunk * 8);
395
396 buf++;
397 chunk++;
398 len--;
399
400 if ((chunk == 4) || ((len == 0) && (blksize == 0))) {
401 sdhci_writel(host, scratch, SDHCI_BUFFER);
402 chunk = 0;
403 scratch = 0;
404 }
405 }
406 }
407
408 sg_miter_stop(&host->sg_miter);
409
410 local_irq_restore(flags);
411}
412
413static void sdhci_transfer_pio(struct sdhci_host *host)
414{
415 u32 mask;
416
417 BUG_ON(!host->data);
418
419 if (host->blocks == 0)
420 return;
421
422 if (host->data->flags & MMC_DATA_READ)
423 mask = SDHCI_DATA_AVAILABLE;
424 else
425 mask = SDHCI_SPACE_AVAILABLE;
426
427 /*
428 * Some controllers (JMicron JMB38x) mess up the buffer bits
429 * for transfers < 4 bytes. As long as it is just one block,
430 * we can ignore the bits.
431 */
432 if ((host->quirks & SDHCI_QUIRK_BROKEN_SMALL_PIO) &&
433 (host->data->blocks == 1))
434 mask = ~0;
435
436 while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {
437 if (host->quirks & SDHCI_QUIRK_PIO_NEEDS_DELAY)
438 udelay(100);
439
440 if (host->data->flags & MMC_DATA_READ)
441 sdhci_read_block_pio(host);
442 else
443 sdhci_write_block_pio(host);
444
445 host->blocks--;
446 if (host->blocks == 0)
447 break;
448 }
449
450 DBG("PIO transfer complete.\n");
451}
452
453static char *sdhci_kmap_atomic(struct scatterlist *sg, unsigned long *flags)
454{
455 local_irq_save(*flags);
456 return kmap_atomic(sg_page(sg)) + sg->offset;
457}
458
459static void sdhci_kunmap_atomic(void *buffer, unsigned long *flags)
460{
461 kunmap_atomic(buffer);
462 local_irq_restore(*flags);
463}
464
465static void sdhci_set_adma_desc(u8 *desc, u32 addr, int len, unsigned cmd)
466{
467 __le32 *dataddr = (__le32 __force *)(desc + 4);
468 __le16 *cmdlen = (__le16 __force *)desc;
469
470 /* SDHCI specification says ADMA descriptors should be 4 byte
471 * aligned, so using 16 or 32bit operations should be safe. */
472
473 cmdlen[0] = cpu_to_le16(cmd);
474 cmdlen[1] = cpu_to_le16(len);
475
476 dataddr[0] = cpu_to_le32(addr);
477}
478
479static int sdhci_adma_table_pre(struct sdhci_host *host,
480 struct mmc_data *data)
481{
482 int direction;
483
484 u8 *desc;
485 u8 *align;
486 dma_addr_t addr;
487 dma_addr_t align_addr;
488 int len, offset;
489
490 struct scatterlist *sg;
491 int i;
492 char *buffer;
493 unsigned long flags;
494
495 /*
496 * The spec does not specify endianness of descriptor table.
497 * We currently guess that it is LE.
498 */
499
500 if (data->flags & MMC_DATA_READ)
501 direction = DMA_FROM_DEVICE;
502 else
503 direction = DMA_TO_DEVICE;
504
505 /*
506 * The ADMA descriptor table is mapped further down as we
507 * need to fill it with data first.
508 */
509
510 host->align_addr = dma_map_single(mmc_dev(host->mmc),
511 host->align_buffer, 128 * 4, direction);
512 if (dma_mapping_error(mmc_dev(host->mmc), host->align_addr))
513 goto fail;
514 BUG_ON(host->align_addr & 0x3);
515
516 host->sg_count = dma_map_sg(mmc_dev(host->mmc),
517 data->sg, data->sg_len, direction);
518 if (host->sg_count == 0)
519 goto unmap_align;
520
521 desc = host->adma_desc;
522 align = host->align_buffer;
523
524 align_addr = host->align_addr;
525
526 for_each_sg(data->sg, sg, host->sg_count, i) {
527 addr = sg_dma_address(sg);
528 len = sg_dma_len(sg);
529
530 /*
531 * The SDHCI specification states that ADMA
532 * addresses must be 32-bit aligned. If they
533 * aren't, then we use a bounce buffer for
534 * the (up to three) bytes that screw up the
535 * alignment.
536 */
537 offset = (4 - (addr & 0x3)) & 0x3;
538 if (offset) {
539 if (data->flags & MMC_DATA_WRITE) {
540 buffer = sdhci_kmap_atomic(sg, &flags);
541 WARN_ON(((long)buffer & PAGE_MASK) > (PAGE_SIZE - 3));
542 memcpy(align, buffer, offset);
543 sdhci_kunmap_atomic(buffer, &flags);
544 }
545
546 /* tran, valid */
547 sdhci_set_adma_desc(desc, align_addr, offset, 0x21);
548
549 BUG_ON(offset > 65536);
550
551 align += 4;
552 align_addr += 4;
553
554 desc += 8;
555
556 addr += offset;
557 len -= offset;
558 }
559
560 BUG_ON(len > 65536);
561
562 /* tran, valid */
563 sdhci_set_adma_desc(desc, addr, len, 0x21);
564 desc += 8;
565
566 /*
567 * If this triggers then we have a calculation bug
568 * somewhere. :/
569 */
570 WARN_ON((desc - host->adma_desc) > (128 * 2 + 1) * 4);
571 }
572
573 if (host->quirks & SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC) {
574 /*
575 * Mark the last descriptor as the terminating descriptor
576 */
577 if (desc != host->adma_desc) {
578 desc -= 8;
579 desc[0] |= 0x2; /* end */
580 }
581 } else {
582 /*
583 * Add a terminating entry.
584 */
585
586 /* nop, end, valid */
587 sdhci_set_adma_desc(desc, 0, 0, 0x3);
588 }
589
590 /*
591 * Resync align buffer as we might have changed it.
592 */
593 if (data->flags & MMC_DATA_WRITE) {
594 dma_sync_single_for_device(mmc_dev(host->mmc),
595 host->align_addr, 128 * 4, direction);
596 }
597
598 host->adma_addr = dma_map_single(mmc_dev(host->mmc),
599 host->adma_desc, (128 * 2 + 1) * 4, DMA_TO_DEVICE);
600 if (dma_mapping_error(mmc_dev(host->mmc), host->adma_addr))
601 goto unmap_entries;
602 BUG_ON(host->adma_addr & 0x3);
603
604 return 0;
605
606unmap_entries:
607 dma_unmap_sg(mmc_dev(host->mmc), data->sg,
608 data->sg_len, direction);
609unmap_align:
610 dma_unmap_single(mmc_dev(host->mmc), host->align_addr,
611 128 * 4, direction);
612fail:
613 return -EINVAL;
614}
615
616static void sdhci_adma_table_post(struct sdhci_host *host,
617 struct mmc_data *data)
618{
619 int direction;
620
621 struct scatterlist *sg;
622 int i, size;
623 u8 *align;
624 char *buffer;
625 unsigned long flags;
626
627 if (data->flags & MMC_DATA_READ)
628 direction = DMA_FROM_DEVICE;
629 else
630 direction = DMA_TO_DEVICE;
631
632 dma_unmap_single(mmc_dev(host->mmc), host->adma_addr,
633 (128 * 2 + 1) * 4, DMA_TO_DEVICE);
634
635 dma_unmap_single(mmc_dev(host->mmc), host->align_addr,
636 128 * 4, direction);
637
638 if (data->flags & MMC_DATA_READ) {
639 dma_sync_sg_for_cpu(mmc_dev(host->mmc), data->sg,
640 data->sg_len, direction);
641
642 align = host->align_buffer;
643
644 for_each_sg(data->sg, sg, host->sg_count, i) {
645 if (sg_dma_address(sg) & 0x3) {
646 size = 4 - (sg_dma_address(sg) & 0x3);
647
648 buffer = sdhci_kmap_atomic(sg, &flags);
649 WARN_ON(((long)buffer & PAGE_MASK) > (PAGE_SIZE - 3));
650 memcpy(buffer, align, size);
651 sdhci_kunmap_atomic(buffer, &flags);
652
653 align += 4;
654 }
655 }
656 }
657
658 dma_unmap_sg(mmc_dev(host->mmc), data->sg,
659 data->sg_len, direction);
660}
661
662static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd)
663{
664 u8 count;
665 struct mmc_data *data = cmd->data;
666 unsigned target_timeout, current_timeout;
667
668 /*
669 * If the host controller provides us with an incorrect timeout
670 * value, just skip the check and use 0xE. The hardware may take
671 * longer to time out, but that's much better than having a too-short
672 * timeout value.
673 */
674 if (host->quirks & SDHCI_QUIRK_BROKEN_TIMEOUT_VAL)
675 return 0xE;
676
677 /* Unspecified timeout, assume max */
678 if (!data && !cmd->busy_timeout)
679 return 0xE;
680
681 /* timeout in us */
682 if (!data)
683 target_timeout = cmd->busy_timeout * 1000;
684 else {
685 target_timeout = data->timeout_ns / 1000;
686 if (host->clock)
687 target_timeout += data->timeout_clks / host->clock;
688 }
689
690 /*
691 * Figure out needed cycles.
692 * We do this in steps in order to fit inside a 32 bit int.
693 * The first step is the minimum timeout, which will have a
694 * minimum resolution of 6 bits:
695 * (1) 2^13*1000 > 2^22,
696 * (2) host->timeout_clk < 2^16
697 * =>
698 * (1) / (2) > 2^6
699 */
700 count = 0;
701 current_timeout = (1 << 13) * 1000 / host->timeout_clk;
702 while (current_timeout < target_timeout) {
703 count++;
704 current_timeout <<= 1;
705 if (count >= 0xF)
706 break;
707 }
708
709 if (count >= 0xF) {
710 DBG("%s: Too large timeout 0x%x requested for CMD%d!\n",
711 mmc_hostname(host->mmc), count, cmd->opcode);
712 count = 0xE;
713 }
714
715 return count;
716}
717
718static void sdhci_set_transfer_irqs(struct sdhci_host *host)
719{
720 u32 pio_irqs = SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL;
721 u32 dma_irqs = SDHCI_INT_DMA_END | SDHCI_INT_ADMA_ERROR;
722
723 if (host->flags & SDHCI_REQ_USE_DMA)
724 sdhci_clear_set_irqs(host, pio_irqs, dma_irqs);
725 else
726 sdhci_clear_set_irqs(host, dma_irqs, pio_irqs);
727}
728
729static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_command *cmd)
730{
731 u8 count;
732 u8 ctrl;
733 struct mmc_data *data = cmd->data;
734 int ret;
735
736 WARN_ON(host->data);
737
738 if (data || (cmd->flags & MMC_RSP_BUSY)) {
739 count = sdhci_calc_timeout(host, cmd);
740 sdhci_writeb(host, count, SDHCI_TIMEOUT_CONTROL);
741 }
742
743 if (!data)
744 return;
745
746 /* Sanity checks */
747 BUG_ON(data->blksz * data->blocks > 524288);
748 BUG_ON(data->blksz > host->mmc->max_blk_size);
749 BUG_ON(data->blocks > 65535);
750
751 host->data = data;
752 host->data_early = 0;
753 host->data->bytes_xfered = 0;
754
755 if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA))
756 host->flags |= SDHCI_REQ_USE_DMA;
757
758 /*
759 * FIXME: This doesn't account for merging when mapping the
760 * scatterlist.
761 */
762 if (host->flags & SDHCI_REQ_USE_DMA) {
763 int broken, i;
764 struct scatterlist *sg;
765
766 broken = 0;
767 if (host->flags & SDHCI_USE_ADMA) {
768 if (host->quirks & SDHCI_QUIRK_32BIT_ADMA_SIZE)
769 broken = 1;
770 } else {
771 if (host->quirks & SDHCI_QUIRK_32BIT_DMA_SIZE)
772 broken = 1;
773 }
774
775 if (unlikely(broken)) {
776 for_each_sg(data->sg, sg, data->sg_len, i) {
777 if (sg->length & 0x3) {
778 DBG("Reverting to PIO because of "
779 "transfer size (%d)\n",
780 sg->length);
781 host->flags &= ~SDHCI_REQ_USE_DMA;
782 break;
783 }
784 }
785 }
786 }
787
788 /*
789 * The assumption here being that alignment is the same after
790 * translation to device address space.
791 */
792 if (host->flags & SDHCI_REQ_USE_DMA) {
793 int broken, i;
794 struct scatterlist *sg;
795
796 broken = 0;
797 if (host->flags & SDHCI_USE_ADMA) {
798 /*
799 * As we use 3 byte chunks to work around
800 * alignment problems, we need to check this
801 * quirk.
802 */
803 if (host->quirks & SDHCI_QUIRK_32BIT_ADMA_SIZE)
804 broken = 1;
805 } else {
806 if (host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR)
807 broken = 1;
808 }
809
810 if (unlikely(broken)) {
811 for_each_sg(data->sg, sg, data->sg_len, i) {
812 if (sg->offset & 0x3) {
813 DBG("Reverting to PIO because of "
814 "bad alignment\n");
815 host->flags &= ~SDHCI_REQ_USE_DMA;
816 break;
817 }
818 }
819 }
820 }
821
822 if (host->flags & SDHCI_REQ_USE_DMA) {
823 if (host->flags & SDHCI_USE_ADMA) {
824 ret = sdhci_adma_table_pre(host, data);
825 if (ret) {
826 /*
827 * This only happens when someone fed
828 * us an invalid request.
829 */
830 WARN_ON(1);
831 host->flags &= ~SDHCI_REQ_USE_DMA;
832 } else {
833 sdhci_writel(host, host->adma_addr,
834 SDHCI_ADMA_ADDRESS);
835 }
836 } else {
837 int sg_cnt;
838
839 sg_cnt = dma_map_sg(mmc_dev(host->mmc),
840 data->sg, data->sg_len,
841 (data->flags & MMC_DATA_READ) ?
842 DMA_FROM_DEVICE :
843 DMA_TO_DEVICE);
844 if (sg_cnt == 0) {
845 /*
846 * This only happens when someone fed
847 * us an invalid request.
848 */
849 WARN_ON(1);
850 host->flags &= ~SDHCI_REQ_USE_DMA;
851 } else {
852 WARN_ON(sg_cnt != 1);
853 sdhci_writel(host, sg_dma_address(data->sg),
854 SDHCI_DMA_ADDRESS);
855 }
856 }
857 }
858
859 /*
860 * Always adjust the DMA selection as some controllers
861 * (e.g. JMicron) can't do PIO properly when the selection
862 * is ADMA.
863 */
864 if (host->version >= SDHCI_SPEC_200) {
865 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
866 ctrl &= ~SDHCI_CTRL_DMA_MASK;
867 if ((host->flags & SDHCI_REQ_USE_DMA) &&
868 (host->flags & SDHCI_USE_ADMA))
869 ctrl |= SDHCI_CTRL_ADMA32;
870 else
871 ctrl |= SDHCI_CTRL_SDMA;
872 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
873 }
874
875 if (!(host->flags & SDHCI_REQ_USE_DMA)) {
876 int flags;
877
878 flags = SG_MITER_ATOMIC;
879 if (host->data->flags & MMC_DATA_READ)
880 flags |= SG_MITER_TO_SG;
881 else
882 flags |= SG_MITER_FROM_SG;
883 sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
884 host->blocks = data->blocks;
885 }
886
887 sdhci_set_transfer_irqs(host);
888
889 /* Set the DMA boundary value and block size */
890 sdhci_writew(host, SDHCI_MAKE_BLKSZ(SDHCI_DEFAULT_BOUNDARY_ARG,
891 data->blksz), SDHCI_BLOCK_SIZE);
892 sdhci_writew(host, data->blocks, SDHCI_BLOCK_COUNT);
893}
894
895static void sdhci_set_transfer_mode(struct sdhci_host *host,
896 struct mmc_command *cmd)
897{
898 u16 mode;
899 struct mmc_data *data = cmd->data;
900
901 if (data == NULL) {
902 /* clear Auto CMD settings for no data CMDs */
903 mode = sdhci_readw(host, SDHCI_TRANSFER_MODE);
904 sdhci_writew(host, mode & ~(SDHCI_TRNS_AUTO_CMD12 |
905 SDHCI_TRNS_AUTO_CMD23), SDHCI_TRANSFER_MODE);
906 return;
907 }
908
909 WARN_ON(!host->data);
910
911 mode = SDHCI_TRNS_BLK_CNT_EN;
912 if (mmc_op_multi(cmd->opcode) || data->blocks > 1) {
913 mode |= SDHCI_TRNS_MULTI;
914 /*
915 * If we are sending CMD23, CMD12 never gets sent
916 * on successful completion (so no Auto-CMD12).
917 */
918 if (!host->mrq->sbc && (host->flags & SDHCI_AUTO_CMD12))
919 mode |= SDHCI_TRNS_AUTO_CMD12;
920 else if (host->mrq->sbc && (host->flags & SDHCI_AUTO_CMD23)) {
921 mode |= SDHCI_TRNS_AUTO_CMD23;
922 sdhci_writel(host, host->mrq->sbc->arg, SDHCI_ARGUMENT2);
923 }
924 }
925
926 if (data->flags & MMC_DATA_READ)
927 mode |= SDHCI_TRNS_READ;
928 if (host->flags & SDHCI_REQ_USE_DMA)
929 mode |= SDHCI_TRNS_DMA;
930
931 sdhci_writew(host, mode, SDHCI_TRANSFER_MODE);
932}
933
934static void sdhci_finish_data(struct sdhci_host *host)
935{
936 struct mmc_data *data;
937
938 BUG_ON(!host->data);
939
940 data = host->data;
941 host->data = NULL;
942
943 if (host->flags & SDHCI_REQ_USE_DMA) {
944 if (host->flags & SDHCI_USE_ADMA)
945 sdhci_adma_table_post(host, data);
946 else {
947 dma_unmap_sg(mmc_dev(host->mmc), data->sg,
948 data->sg_len, (data->flags & MMC_DATA_READ) ?
949 DMA_FROM_DEVICE : DMA_TO_DEVICE);
950 }
951 }
952
953 /*
954 * The specification states that the block count register must
955 * be updated, but it does not specify at what point in the
956 * data flow. That makes the register entirely useless to read
957 * back so we have to assume that nothing made it to the card
958 * in the event of an error.
959 */
960 if (data->error)
961 data->bytes_xfered = 0;
962 else
963 data->bytes_xfered = data->blksz * data->blocks;
964
965 /*
966 * Need to send CMD12 if -
967 * a) open-ended multiblock transfer (no CMD23)
968 * b) error in multiblock transfer
969 */
970 if (data->stop &&
971 (data->error ||
972 !host->mrq->sbc)) {
973
974 /*
975 * The controller needs a reset of internal state machines
976 * upon error conditions.
977 */
978 if (data->error) {
979 sdhci_reset(host, SDHCI_RESET_CMD);
980 sdhci_reset(host, SDHCI_RESET_DATA);
981 }
982
983 sdhci_send_command(host, data->stop);
984 } else
985 tasklet_schedule(&host->finish_tasklet);
986}
987
988void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd)
989{
990 int flags;
991 u32 mask;
992 unsigned long timeout;
993
994 WARN_ON(host->cmd);
995
996 /* Wait max 10 ms */
997 timeout = 10;
998
999 mask = SDHCI_CMD_INHIBIT;
1000 if ((cmd->data != NULL) || (cmd->flags & MMC_RSP_BUSY))
1001 mask |= SDHCI_DATA_INHIBIT;
1002
1003 /* We shouldn't wait for data inihibit for stop commands, even
1004 though they might use busy signaling */
1005 if (host->mrq->data && (cmd == host->mrq->data->stop))
1006 mask &= ~SDHCI_DATA_INHIBIT;
1007
1008 while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {
1009 if (timeout == 0) {
1010 pr_err("%s: Controller never released "
1011 "inhibit bit(s).\n", mmc_hostname(host->mmc));
1012 sdhci_dumpregs(host);
1013 cmd->error = -EIO;
1014 tasklet_schedule(&host->finish_tasklet);
1015 return;
1016 }
1017 timeout--;
1018 mdelay(1);
1019 }
1020
1021 timeout = jiffies;
1022 if (!cmd->data && cmd->busy_timeout > 9000)
1023 timeout += DIV_ROUND_UP(cmd->busy_timeout, 1000) * HZ + HZ;
1024 else
1025 timeout += 10 * HZ;
1026 mod_timer(&host->timer, timeout);
1027
1028 host->cmd = cmd;
1029
1030 sdhci_prepare_data(host, cmd);
1031
1032 sdhci_writel(host, cmd->arg, SDHCI_ARGUMENT);
1033
1034 sdhci_set_transfer_mode(host, cmd);
1035
1036 if ((cmd->flags & MMC_RSP_136) && (cmd->flags & MMC_RSP_BUSY)) {
1037 pr_err("%s: Unsupported response type!\n",
1038 mmc_hostname(host->mmc));
1039 cmd->error = -EINVAL;
1040 tasklet_schedule(&host->finish_tasklet);
1041 return;
1042 }
1043
1044 if (!(cmd->flags & MMC_RSP_PRESENT))
1045 flags = SDHCI_CMD_RESP_NONE;
1046 else if (cmd->flags & MMC_RSP_136)
1047 flags = SDHCI_CMD_RESP_LONG;
1048 else if (cmd->flags & MMC_RSP_BUSY)
1049 flags = SDHCI_CMD_RESP_SHORT_BUSY;
1050 else
1051 flags = SDHCI_CMD_RESP_SHORT;
1052
1053 if (cmd->flags & MMC_RSP_CRC)
1054 flags |= SDHCI_CMD_CRC;
1055 if (cmd->flags & MMC_RSP_OPCODE)
1056 flags |= SDHCI_CMD_INDEX;
1057
1058 /* CMD19 is special in that the Data Present Select should be set */
1059 if (cmd->data || cmd->opcode == MMC_SEND_TUNING_BLOCK ||
1060 cmd->opcode == MMC_SEND_TUNING_BLOCK_HS200)
1061 flags |= SDHCI_CMD_DATA;
1062
1063 sdhci_writew(host, SDHCI_MAKE_CMD(cmd->opcode, flags), SDHCI_COMMAND);
1064}
1065EXPORT_SYMBOL_GPL(sdhci_send_command);
1066
1067static void sdhci_finish_command(struct sdhci_host *host)
1068{
1069 int i;
1070
1071 BUG_ON(host->cmd == NULL);
1072
1073 if (host->cmd->flags & MMC_RSP_PRESENT) {
1074 if (host->cmd->flags & MMC_RSP_136) {
1075 /* CRC is stripped so we need to do some shifting. */
1076 for (i = 0;i < 4;i++) {
1077 host->cmd->resp[i] = sdhci_readl(host,
1078 SDHCI_RESPONSE + (3-i)*4) << 8;
1079 if (i != 3)
1080 host->cmd->resp[i] |=
1081 sdhci_readb(host,
1082 SDHCI_RESPONSE + (3-i)*4-1);
1083 }
1084 } else {
1085 host->cmd->resp[0] = sdhci_readl(host, SDHCI_RESPONSE);
1086 }
1087 }
1088
1089 host->cmd->error = 0;
1090
1091 /* Finished CMD23, now send actual command. */
1092 if (host->cmd == host->mrq->sbc) {
1093 host->cmd = NULL;
1094 sdhci_send_command(host, host->mrq->cmd);
1095 } else {
1096
1097 /* Processed actual command. */
1098 if (host->data && host->data_early)
1099 sdhci_finish_data(host);
1100
1101 if (!host->cmd->data)
1102 tasklet_schedule(&host->finish_tasklet);
1103
1104 host->cmd = NULL;
1105 }
1106}
1107
1108static u16 sdhci_get_preset_value(struct sdhci_host *host)
1109{
1110 u16 ctrl, preset = 0;
1111
1112 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1113
1114 switch (ctrl & SDHCI_CTRL_UHS_MASK) {
1115 case SDHCI_CTRL_UHS_SDR12:
1116 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR12);
1117 break;
1118 case SDHCI_CTRL_UHS_SDR25:
1119 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR25);
1120 break;
1121 case SDHCI_CTRL_UHS_SDR50:
1122 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR50);
1123 break;
1124 case SDHCI_CTRL_UHS_SDR104:
1125 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR104);
1126 break;
1127 case SDHCI_CTRL_UHS_DDR50:
1128 preset = sdhci_readw(host, SDHCI_PRESET_FOR_DDR50);
1129 break;
1130 default:
1131 pr_warn("%s: Invalid UHS-I mode selected\n",
1132 mmc_hostname(host->mmc));
1133 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR12);
1134 break;
1135 }
1136 return preset;
1137}
1138
1139static void sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
1140{
1141 int div = 0; /* Initialized for compiler warning */
1142 int real_div = div, clk_mul = 1;
1143 u16 clk = 0;
1144 unsigned long timeout;
1145
1146 if (clock && clock == host->clock)
1147 return;
1148
1149 host->mmc->actual_clock = 0;
1150
1151 if (host->ops->set_clock) {
1152 host->ops->set_clock(host, clock);
1153 if (host->quirks & SDHCI_QUIRK_NONSTANDARD_CLOCK)
1154 return;
1155 }
1156
1157 sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
1158
1159 if (clock == 0)
1160 goto out;
1161
1162 if (host->version >= SDHCI_SPEC_300) {
1163 if (sdhci_readw(host, SDHCI_HOST_CONTROL2) &
1164 SDHCI_CTRL_PRESET_VAL_ENABLE) {
1165 u16 pre_val;
1166
1167 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1168 pre_val = sdhci_get_preset_value(host);
1169 div = (pre_val & SDHCI_PRESET_SDCLK_FREQ_MASK)
1170 >> SDHCI_PRESET_SDCLK_FREQ_SHIFT;
1171 if (host->clk_mul &&
1172 (pre_val & SDHCI_PRESET_CLKGEN_SEL_MASK)) {
1173 clk = SDHCI_PROG_CLOCK_MODE;
1174 real_div = div + 1;
1175 clk_mul = host->clk_mul;
1176 } else {
1177 real_div = max_t(int, 1, div << 1);
1178 }
1179 goto clock_set;
1180 }
1181
1182 /*
1183 * Check if the Host Controller supports Programmable Clock
1184 * Mode.
1185 */
1186 if (host->clk_mul) {
1187 for (div = 1; div <= 1024; div++) {
1188 if ((host->max_clk * host->clk_mul / div)
1189 <= clock)
1190 break;
1191 }
1192 /*
1193 * Set Programmable Clock Mode in the Clock
1194 * Control register.
1195 */
1196 clk = SDHCI_PROG_CLOCK_MODE;
1197 real_div = div;
1198 clk_mul = host->clk_mul;
1199 div--;
1200 } else {
1201 /* Version 3.00 divisors must be a multiple of 2. */
1202 if (host->max_clk <= clock)
1203 div = 1;
1204 else {
1205 for (div = 2; div < SDHCI_MAX_DIV_SPEC_300;
1206 div += 2) {
1207 if ((host->max_clk / div) <= clock)
1208 break;
1209 }
1210 }
1211 real_div = div;
1212 div >>= 1;
1213 }
1214 } else {
1215 /* Version 2.00 divisors must be a power of 2. */
1216 for (div = 1; div < SDHCI_MAX_DIV_SPEC_200; div *= 2) {
1217 if ((host->max_clk / div) <= clock)
1218 break;
1219 }
1220 real_div = div;
1221 div >>= 1;
1222 }
1223
1224clock_set:
1225 if (real_div)
1226 host->mmc->actual_clock = (host->max_clk * clk_mul) / real_div;
1227
1228 clk |= (div & SDHCI_DIV_MASK) << SDHCI_DIVIDER_SHIFT;
1229 clk |= ((div & SDHCI_DIV_HI_MASK) >> SDHCI_DIV_MASK_LEN)
1230 << SDHCI_DIVIDER_HI_SHIFT;
1231 clk |= SDHCI_CLOCK_INT_EN;
1232 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1233
1234 /* Wait max 20 ms */
1235 timeout = 20;
1236 while (!((clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL))
1237 & SDHCI_CLOCK_INT_STABLE)) {
1238 if (timeout == 0) {
1239 pr_err("%s: Internal clock never "
1240 "stabilised.\n", mmc_hostname(host->mmc));
1241 sdhci_dumpregs(host);
1242 return;
1243 }
1244 timeout--;
1245 mdelay(1);
1246 }
1247
1248 clk |= SDHCI_CLOCK_CARD_EN;
1249 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1250
1251out:
1252 host->clock = clock;
1253}
1254
1255static inline void sdhci_update_clock(struct sdhci_host *host)
1256{
1257 unsigned int clock;
1258
1259 clock = host->clock;
1260 host->clock = 0;
1261 sdhci_set_clock(host, clock);
1262}
1263
1264static int sdhci_set_power(struct sdhci_host *host, unsigned short power)
1265{
1266 u8 pwr = 0;
1267
1268 if (power != (unsigned short)-1) {
1269 switch (1 << power) {
1270 case MMC_VDD_165_195:
1271 pwr = SDHCI_POWER_180;
1272 break;
1273 case MMC_VDD_29_30:
1274 case MMC_VDD_30_31:
1275 pwr = SDHCI_POWER_300;
1276 break;
1277 case MMC_VDD_32_33:
1278 case MMC_VDD_33_34:
1279 pwr = SDHCI_POWER_330;
1280 break;
1281 default:
1282 BUG();
1283 }
1284 }
1285
1286 if (host->pwr == pwr)
1287 return -1;
1288
1289 host->pwr = pwr;
1290
1291 if (pwr == 0) {
1292 sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
1293 if (host->quirks2 & SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON)
1294 sdhci_runtime_pm_bus_off(host);
1295 return 0;
1296 }
1297
1298 /*
1299 * Spec says that we should clear the power reg before setting
1300 * a new value. Some controllers don't seem to like this though.
1301 */
1302 if (!(host->quirks & SDHCI_QUIRK_SINGLE_POWER_WRITE))
1303 sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
1304
1305 /*
1306 * At least the Marvell CaFe chip gets confused if we set the voltage
1307 * and set turn on power at the same time, so set the voltage first.
1308 */
1309 if (host->quirks & SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER)
1310 sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
1311
1312 pwr |= SDHCI_POWER_ON;
1313
1314 sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
1315
1316 if (host->quirks2 & SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON)
1317 sdhci_runtime_pm_bus_on(host);
1318
1319 /*
1320 * Some controllers need an extra 10ms delay of 10ms before they
1321 * can apply clock after applying power
1322 */
1323 if (host->quirks & SDHCI_QUIRK_DELAY_AFTER_POWER)
1324 mdelay(10);
1325
1326 return power;
1327}
1328
1329/*****************************************************************************\
1330 * *
1331 * MMC callbacks *
1332 * *
1333\*****************************************************************************/
1334
1335static void sdhci_request(struct mmc_host *mmc, struct mmc_request *mrq)
1336{
1337 struct sdhci_host *host;
1338 int present;
1339 unsigned long flags;
1340 u32 tuning_opcode;
1341
1342 host = mmc_priv(mmc);
1343
1344 sdhci_runtime_pm_get(host);
1345
1346 spin_lock_irqsave(&host->lock, flags);
1347
1348 WARN_ON(host->mrq != NULL);
1349
1350#ifndef SDHCI_USE_LEDS_CLASS
1351 sdhci_activate_led(host);
1352#endif
1353
1354 /*
1355 * Ensure we don't send the STOP for non-SET_BLOCK_COUNTED
1356 * requests if Auto-CMD12 is enabled.
1357 */
1358 if (!mrq->sbc && (host->flags & SDHCI_AUTO_CMD12)) {
1359 if (mrq->stop) {
1360 mrq->data->stop = NULL;
1361 mrq->stop = NULL;
1362 }
1363 }
1364
1365 host->mrq = mrq;
1366
1367 /*
1368 * Firstly check card presence from cd-gpio. The return could
1369 * be one of the following possibilities:
1370 * negative: cd-gpio is not available
1371 * zero: cd-gpio is used, and card is removed
1372 * one: cd-gpio is used, and card is present
1373 */
1374 present = mmc_gpio_get_cd(host->mmc);
1375 if (present < 0) {
1376 /* If polling, assume that the card is always present. */
1377 if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
1378 present = 1;
1379 else
1380 present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
1381 SDHCI_CARD_PRESENT;
1382 }
1383
1384 if (!present || host->flags & SDHCI_DEVICE_DEAD) {
1385 host->mrq->cmd->error = -ENOMEDIUM;
1386 tasklet_schedule(&host->finish_tasklet);
1387 } else {
1388 u32 present_state;
1389
1390 present_state = sdhci_readl(host, SDHCI_PRESENT_STATE);
1391 /*
1392 * Check if the re-tuning timer has already expired and there
1393 * is no on-going data transfer. If so, we need to execute
1394 * tuning procedure before sending command.
1395 */
1396 if ((host->flags & SDHCI_NEEDS_RETUNING) &&
1397 !(present_state & (SDHCI_DOING_WRITE | SDHCI_DOING_READ))) {
1398 if (mmc->card) {
1399 /* eMMC uses cmd21 but sd and sdio use cmd19 */
1400 tuning_opcode =
1401 mmc->card->type == MMC_TYPE_MMC ?
1402 MMC_SEND_TUNING_BLOCK_HS200 :
1403 MMC_SEND_TUNING_BLOCK;
1404
1405 /* Here we need to set the host->mrq to NULL,
1406 * in case the pending finish_tasklet
1407 * finishes it incorrectly.
1408 */
1409 host->mrq = NULL;
1410
1411 spin_unlock_irqrestore(&host->lock, flags);
1412 sdhci_execute_tuning(mmc, tuning_opcode);
1413 spin_lock_irqsave(&host->lock, flags);
1414
1415 /* Restore original mmc_request structure */
1416 host->mrq = mrq;
1417 }
1418 }
1419
1420 if (mrq->sbc && !(host->flags & SDHCI_AUTO_CMD23))
1421 sdhci_send_command(host, mrq->sbc);
1422 else
1423 sdhci_send_command(host, mrq->cmd);
1424 }
1425
1426 mmiowb();
1427 spin_unlock_irqrestore(&host->lock, flags);
1428}
1429
1430static void sdhci_do_set_ios(struct sdhci_host *host, struct mmc_ios *ios)
1431{
1432 unsigned long flags;
1433 int vdd_bit = -1;
1434 u8 ctrl;
1435
1436 spin_lock_irqsave(&host->lock, flags);
1437
1438 if (host->flags & SDHCI_DEVICE_DEAD) {
1439 spin_unlock_irqrestore(&host->lock, flags);
1440 if (host->vmmc && ios->power_mode == MMC_POWER_OFF)
1441 mmc_regulator_set_ocr(host->mmc, host->vmmc, 0);
1442 return;
1443 }
1444
1445 /*
1446 * Reset the chip on each power off.
1447 * Should clear out any weird states.
1448 */
1449 if (ios->power_mode == MMC_POWER_OFF) {
1450 sdhci_writel(host, 0, SDHCI_SIGNAL_ENABLE);
1451 sdhci_reinit(host);
1452 }
1453
1454 if (host->version >= SDHCI_SPEC_300 &&
1455 (ios->power_mode == MMC_POWER_UP) &&
1456 !(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN))
1457 sdhci_enable_preset_value(host, false);
1458
1459 sdhci_set_clock(host, ios->clock);
1460
1461 if (ios->power_mode == MMC_POWER_OFF)
1462 vdd_bit = sdhci_set_power(host, -1);
1463 else
1464 vdd_bit = sdhci_set_power(host, ios->vdd);
1465
1466 if (host->vmmc && vdd_bit != -1) {
1467 spin_unlock_irqrestore(&host->lock, flags);
1468 mmc_regulator_set_ocr(host->mmc, host->vmmc, vdd_bit);
1469 spin_lock_irqsave(&host->lock, flags);
1470 }
1471
1472 if (host->ops->platform_send_init_74_clocks)
1473 host->ops->platform_send_init_74_clocks(host, ios->power_mode);
1474
1475 /*
1476 * If your platform has 8-bit width support but is not a v3 controller,
1477 * or if it requires special setup code, you should implement that in
1478 * platform_bus_width().
1479 */
1480 if (host->ops->platform_bus_width) {
1481 host->ops->platform_bus_width(host, ios->bus_width);
1482 } else {
1483 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
1484 if (ios->bus_width == MMC_BUS_WIDTH_8) {
1485 ctrl &= ~SDHCI_CTRL_4BITBUS;
1486 if (host->version >= SDHCI_SPEC_300)
1487 ctrl |= SDHCI_CTRL_8BITBUS;
1488 } else {
1489 if (host->version >= SDHCI_SPEC_300)
1490 ctrl &= ~SDHCI_CTRL_8BITBUS;
1491 if (ios->bus_width == MMC_BUS_WIDTH_4)
1492 ctrl |= SDHCI_CTRL_4BITBUS;
1493 else
1494 ctrl &= ~SDHCI_CTRL_4BITBUS;
1495 }
1496 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
1497 }
1498
1499 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
1500
1501 if ((ios->timing == MMC_TIMING_SD_HS ||
1502 ios->timing == MMC_TIMING_MMC_HS)
1503 && !(host->quirks & SDHCI_QUIRK_NO_HISPD_BIT))
1504 ctrl |= SDHCI_CTRL_HISPD;
1505 else
1506 ctrl &= ~SDHCI_CTRL_HISPD;
1507
1508 if (host->version >= SDHCI_SPEC_300) {
1509 u16 clk, ctrl_2;
1510
1511 /* In case of UHS-I modes, set High Speed Enable */
1512 if ((ios->timing == MMC_TIMING_MMC_HS200) ||
1513 (ios->timing == MMC_TIMING_UHS_SDR50) ||
1514 (ios->timing == MMC_TIMING_UHS_SDR104) ||
1515 (ios->timing == MMC_TIMING_UHS_DDR50) ||
1516 (ios->timing == MMC_TIMING_UHS_SDR25))
1517 ctrl |= SDHCI_CTRL_HISPD;
1518
1519 ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1520 if (!(ctrl_2 & SDHCI_CTRL_PRESET_VAL_ENABLE)) {
1521 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
1522 /*
1523 * We only need to set Driver Strength if the
1524 * preset value enable is not set.
1525 */
1526 ctrl_2 &= ~SDHCI_CTRL_DRV_TYPE_MASK;
1527 if (ios->drv_type == MMC_SET_DRIVER_TYPE_A)
1528 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_A;
1529 else if (ios->drv_type == MMC_SET_DRIVER_TYPE_C)
1530 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_C;
1531
1532 sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
1533 } else {
1534 /*
1535 * According to SDHC Spec v3.00, if the Preset Value
1536 * Enable in the Host Control 2 register is set, we
1537 * need to reset SD Clock Enable before changing High
1538 * Speed Enable to avoid generating clock gliches.
1539 */
1540
1541 /* Reset SD Clock Enable */
1542 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1543 clk &= ~SDHCI_CLOCK_CARD_EN;
1544 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1545
1546 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
1547
1548 /* Re-enable SD Clock */
1549 sdhci_update_clock(host);
1550 }
1551
1552
1553 /* Reset SD Clock Enable */
1554 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1555 clk &= ~SDHCI_CLOCK_CARD_EN;
1556 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1557
1558 if (host->ops->set_uhs_signaling)
1559 host->ops->set_uhs_signaling(host, ios->timing);
1560 else {
1561 ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1562 /* Select Bus Speed Mode for host */
1563 ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
1564 if ((ios->timing == MMC_TIMING_MMC_HS200) ||
1565 (ios->timing == MMC_TIMING_UHS_SDR104))
1566 ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
1567 else if (ios->timing == MMC_TIMING_UHS_SDR12)
1568 ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
1569 else if (ios->timing == MMC_TIMING_UHS_SDR25)
1570 ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
1571 else if (ios->timing == MMC_TIMING_UHS_SDR50)
1572 ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
1573 else if (ios->timing == MMC_TIMING_UHS_DDR50)
1574 ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
1575 sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
1576 }
1577
1578 if (!(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN) &&
1579 ((ios->timing == MMC_TIMING_UHS_SDR12) ||
1580 (ios->timing == MMC_TIMING_UHS_SDR25) ||
1581 (ios->timing == MMC_TIMING_UHS_SDR50) ||
1582 (ios->timing == MMC_TIMING_UHS_SDR104) ||
1583 (ios->timing == MMC_TIMING_UHS_DDR50))) {
1584 u16 preset;
1585
1586 sdhci_enable_preset_value(host, true);
1587 preset = sdhci_get_preset_value(host);
1588 ios->drv_type = (preset & SDHCI_PRESET_DRV_MASK)
1589 >> SDHCI_PRESET_DRV_SHIFT;
1590 }
1591
1592 /* Re-enable SD Clock */
1593 sdhci_update_clock(host);
1594 } else
1595 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
1596
1597 /*
1598 * Some (ENE) controllers go apeshit on some ios operation,
1599 * signalling timeout and CRC errors even on CMD0. Resetting
1600 * it on each ios seems to solve the problem.
1601 */
1602 if(host->quirks & SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS)
1603 sdhci_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA);
1604
1605 mmiowb();
1606 spin_unlock_irqrestore(&host->lock, flags);
1607}
1608
1609static void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
1610{
1611 struct sdhci_host *host = mmc_priv(mmc);
1612
1613 sdhci_runtime_pm_get(host);
1614 sdhci_do_set_ios(host, ios);
1615 sdhci_runtime_pm_put(host);
1616}
1617
1618static int sdhci_do_get_cd(struct sdhci_host *host)
1619{
1620 int gpio_cd = mmc_gpio_get_cd(host->mmc);
1621
1622 if (host->flags & SDHCI_DEVICE_DEAD)
1623 return 0;
1624
1625 /* If polling/nonremovable, assume that the card is always present. */
1626 if ((host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) ||
1627 (host->mmc->caps & MMC_CAP_NONREMOVABLE))
1628 return 1;
1629
1630 /* Try slot gpio detect */
1631 if (!IS_ERR_VALUE(gpio_cd))
1632 return !!gpio_cd;
1633
1634 /* Host native card detect */
1635 return !!(sdhci_readl(host, SDHCI_PRESENT_STATE) & SDHCI_CARD_PRESENT);
1636}
1637
1638static int sdhci_get_cd(struct mmc_host *mmc)
1639{
1640 struct sdhci_host *host = mmc_priv(mmc);
1641 int ret;
1642
1643 sdhci_runtime_pm_get(host);
1644 ret = sdhci_do_get_cd(host);
1645 sdhci_runtime_pm_put(host);
1646 return ret;
1647}
1648
1649static int sdhci_check_ro(struct sdhci_host *host)
1650{
1651 unsigned long flags;
1652 int is_readonly;
1653
1654 spin_lock_irqsave(&host->lock, flags);
1655
1656 if (host->flags & SDHCI_DEVICE_DEAD)
1657 is_readonly = 0;
1658 else if (host->ops->get_ro)
1659 is_readonly = host->ops->get_ro(host);
1660 else
1661 is_readonly = !(sdhci_readl(host, SDHCI_PRESENT_STATE)
1662 & SDHCI_WRITE_PROTECT);
1663
1664 spin_unlock_irqrestore(&host->lock, flags);
1665
1666 /* This quirk needs to be replaced by a callback-function later */
1667 return host->quirks & SDHCI_QUIRK_INVERTED_WRITE_PROTECT ?
1668 !is_readonly : is_readonly;
1669}
1670
1671#define SAMPLE_COUNT 5
1672
1673static int sdhci_do_get_ro(struct sdhci_host *host)
1674{
1675 int i, ro_count;
1676
1677 if (!(host->quirks & SDHCI_QUIRK_UNSTABLE_RO_DETECT))
1678 return sdhci_check_ro(host);
1679
1680 ro_count = 0;
1681 for (i = 0; i < SAMPLE_COUNT; i++) {
1682 if (sdhci_check_ro(host)) {
1683 if (++ro_count > SAMPLE_COUNT / 2)
1684 return 1;
1685 }
1686 msleep(30);
1687 }
1688 return 0;
1689}
1690
1691static void sdhci_hw_reset(struct mmc_host *mmc)
1692{
1693 struct sdhci_host *host = mmc_priv(mmc);
1694
1695 if (host->ops && host->ops->hw_reset)
1696 host->ops->hw_reset(host);
1697}
1698
1699static int sdhci_get_ro(struct mmc_host *mmc)
1700{
1701 struct sdhci_host *host = mmc_priv(mmc);
1702 int ret;
1703
1704 sdhci_runtime_pm_get(host);
1705 ret = sdhci_do_get_ro(host);
1706 sdhci_runtime_pm_put(host);
1707 return ret;
1708}
1709
1710static void sdhci_enable_sdio_irq_nolock(struct sdhci_host *host, int enable)
1711{
1712 if (host->flags & SDHCI_DEVICE_DEAD)
1713 goto out;
1714
1715 if (enable)
1716 host->flags |= SDHCI_SDIO_IRQ_ENABLED;
1717 else
1718 host->flags &= ~SDHCI_SDIO_IRQ_ENABLED;
1719
1720 /* SDIO IRQ will be enabled as appropriate in runtime resume */
1721 if (host->runtime_suspended)
1722 goto out;
1723
1724 if (enable)
1725 sdhci_unmask_irqs(host, SDHCI_INT_CARD_INT);
1726 else
1727 sdhci_mask_irqs(host, SDHCI_INT_CARD_INT);
1728out:
1729 mmiowb();
1730}
1731
1732static void sdhci_enable_sdio_irq(struct mmc_host *mmc, int enable)
1733{
1734 struct sdhci_host *host = mmc_priv(mmc);
1735 unsigned long flags;
1736
1737 spin_lock_irqsave(&host->lock, flags);
1738 sdhci_enable_sdio_irq_nolock(host, enable);
1739 spin_unlock_irqrestore(&host->lock, flags);
1740}
1741
1742static int sdhci_do_start_signal_voltage_switch(struct sdhci_host *host,
1743 struct mmc_ios *ios)
1744{
1745 u16 ctrl;
1746 int ret;
1747
1748 /*
1749 * Signal Voltage Switching is only applicable for Host Controllers
1750 * v3.00 and above.
1751 */
1752 if (host->version < SDHCI_SPEC_300)
1753 return 0;
1754
1755 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1756
1757 switch (ios->signal_voltage) {
1758 case MMC_SIGNAL_VOLTAGE_330:
1759 /* Set 1.8V Signal Enable in the Host Control2 register to 0 */
1760 ctrl &= ~SDHCI_CTRL_VDD_180;
1761 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1762
1763 if (host->vqmmc) {
1764 ret = regulator_set_voltage(host->vqmmc, 2700000, 3600000);
1765 if (ret) {
1766 pr_warning("%s: Switching to 3.3V signalling voltage "
1767 " failed\n", mmc_hostname(host->mmc));
1768 return -EIO;
1769 }
1770 }
1771 /* Wait for 5ms */
1772 usleep_range(5000, 5500);
1773
1774 /* 3.3V regulator output should be stable within 5 ms */
1775 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1776 if (!(ctrl & SDHCI_CTRL_VDD_180))
1777 return 0;
1778
1779 pr_warning("%s: 3.3V regulator output did not became stable\n",
1780 mmc_hostname(host->mmc));
1781
1782 return -EAGAIN;
1783 case MMC_SIGNAL_VOLTAGE_180:
1784 if (host->vqmmc) {
1785 ret = regulator_set_voltage(host->vqmmc,
1786 1700000, 1950000);
1787 if (ret) {
1788 pr_warning("%s: Switching to 1.8V signalling voltage "
1789 " failed\n", mmc_hostname(host->mmc));
1790 return -EIO;
1791 }
1792 }
1793
1794 /*
1795 * Enable 1.8V Signal Enable in the Host Control2
1796 * register
1797 */
1798 ctrl |= SDHCI_CTRL_VDD_180;
1799 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1800
1801 /* Wait for 5ms */
1802 usleep_range(5000, 5500);
1803
1804 /* 1.8V regulator output should be stable within 5 ms */
1805 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1806 if (ctrl & SDHCI_CTRL_VDD_180)
1807 return 0;
1808
1809 pr_warning("%s: 1.8V regulator output did not became stable\n",
1810 mmc_hostname(host->mmc));
1811
1812 return -EAGAIN;
1813 case MMC_SIGNAL_VOLTAGE_120:
1814 if (host->vqmmc) {
1815 ret = regulator_set_voltage(host->vqmmc, 1100000, 1300000);
1816 if (ret) {
1817 pr_warning("%s: Switching to 1.2V signalling voltage "
1818 " failed\n", mmc_hostname(host->mmc));
1819 return -EIO;
1820 }
1821 }
1822 return 0;
1823 default:
1824 /* No signal voltage switch required */
1825 return 0;
1826 }
1827}
1828
1829static int sdhci_start_signal_voltage_switch(struct mmc_host *mmc,
1830 struct mmc_ios *ios)
1831{
1832 struct sdhci_host *host = mmc_priv(mmc);
1833 int err;
1834
1835 if (host->version < SDHCI_SPEC_300)
1836 return 0;
1837 sdhci_runtime_pm_get(host);
1838 err = sdhci_do_start_signal_voltage_switch(host, ios);
1839 sdhci_runtime_pm_put(host);
1840 return err;
1841}
1842
1843static int sdhci_card_busy(struct mmc_host *mmc)
1844{
1845 struct sdhci_host *host = mmc_priv(mmc);
1846 u32 present_state;
1847
1848 sdhci_runtime_pm_get(host);
1849 /* Check whether DAT[3:0] is 0000 */
1850 present_state = sdhci_readl(host, SDHCI_PRESENT_STATE);
1851 sdhci_runtime_pm_put(host);
1852
1853 return !(present_state & SDHCI_DATA_LVL_MASK);
1854}
1855
1856static int sdhci_execute_tuning(struct mmc_host *mmc, u32 opcode)
1857{
1858 struct sdhci_host *host;
1859 u16 ctrl;
1860 u32 ier;
1861 int tuning_loop_counter = MAX_TUNING_LOOP;
1862 unsigned long timeout;
1863 int err = 0;
1864 bool requires_tuning_nonuhs = false;
1865 unsigned long flags;
1866
1867 host = mmc_priv(mmc);
1868
1869 sdhci_runtime_pm_get(host);
1870 spin_lock_irqsave(&host->lock, flags);
1871
1872 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1873
1874 /*
1875 * The Host Controller needs tuning only in case of SDR104 mode
1876 * and for SDR50 mode when Use Tuning for SDR50 is set in the
1877 * Capabilities register.
1878 * If the Host Controller supports the HS200 mode then the
1879 * tuning function has to be executed.
1880 */
1881 if (((ctrl & SDHCI_CTRL_UHS_MASK) == SDHCI_CTRL_UHS_SDR50) &&
1882 (host->flags & SDHCI_SDR50_NEEDS_TUNING ||
1883 host->flags & SDHCI_SDR104_NEEDS_TUNING))
1884 requires_tuning_nonuhs = true;
1885
1886 if (((ctrl & SDHCI_CTRL_UHS_MASK) == SDHCI_CTRL_UHS_SDR104) ||
1887 requires_tuning_nonuhs)
1888 ctrl |= SDHCI_CTRL_EXEC_TUNING;
1889 else {
1890 spin_unlock_irqrestore(&host->lock, flags);
1891 sdhci_runtime_pm_put(host);
1892 return 0;
1893 }
1894
1895 if (host->ops->platform_execute_tuning) {
1896 spin_unlock_irqrestore(&host->lock, flags);
1897 err = host->ops->platform_execute_tuning(host, opcode);
1898 sdhci_runtime_pm_put(host);
1899 return err;
1900 }
1901
1902 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1903
1904 /*
1905 * As per the Host Controller spec v3.00, tuning command
1906 * generates Buffer Read Ready interrupt, so enable that.
1907 *
1908 * Note: The spec clearly says that when tuning sequence
1909 * is being performed, the controller does not generate
1910 * interrupts other than Buffer Read Ready interrupt. But
1911 * to make sure we don't hit a controller bug, we _only_
1912 * enable Buffer Read Ready interrupt here.
1913 */
1914 ier = sdhci_readl(host, SDHCI_INT_ENABLE);
1915 sdhci_clear_set_irqs(host, ier, SDHCI_INT_DATA_AVAIL);
1916
1917 /*
1918 * Issue CMD19 repeatedly till Execute Tuning is set to 0 or the number
1919 * of loops reaches 40 times or a timeout of 150ms occurs.
1920 */
1921 timeout = 150;
1922 do {
1923 struct mmc_command cmd = {0};
1924 struct mmc_request mrq = {NULL};
1925
1926 if (!tuning_loop_counter && !timeout)
1927 break;
1928
1929 cmd.opcode = opcode;
1930 cmd.arg = 0;
1931 cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
1932 cmd.retries = 0;
1933 cmd.data = NULL;
1934 cmd.error = 0;
1935
1936 mrq.cmd = &cmd;
1937 host->mrq = &mrq;
1938
1939 /*
1940 * In response to CMD19, the card sends 64 bytes of tuning
1941 * block to the Host Controller. So we set the block size
1942 * to 64 here.
1943 */
1944 if (cmd.opcode == MMC_SEND_TUNING_BLOCK_HS200) {
1945 if (mmc->ios.bus_width == MMC_BUS_WIDTH_8)
1946 sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, 128),
1947 SDHCI_BLOCK_SIZE);
1948 else if (mmc->ios.bus_width == MMC_BUS_WIDTH_4)
1949 sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, 64),
1950 SDHCI_BLOCK_SIZE);
1951 } else {
1952 sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, 64),
1953 SDHCI_BLOCK_SIZE);
1954 }
1955
1956 /*
1957 * The tuning block is sent by the card to the host controller.
1958 * So we set the TRNS_READ bit in the Transfer Mode register.
1959 * This also takes care of setting DMA Enable and Multi Block
1960 * Select in the same register to 0.
1961 */
1962 sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE);
1963
1964 sdhci_send_command(host, &cmd);
1965
1966 host->cmd = NULL;
1967 host->mrq = NULL;
1968
1969 spin_unlock_irqrestore(&host->lock, flags);
1970 /* Wait for Buffer Read Ready interrupt */
1971 wait_event_interruptible_timeout(host->buf_ready_int,
1972 (host->tuning_done == 1),
1973 msecs_to_jiffies(50));
1974 spin_lock_irqsave(&host->lock, flags);
1975
1976 if (!host->tuning_done) {
1977 pr_info(DRIVER_NAME ": Timeout waiting for "
1978 "Buffer Read Ready interrupt during tuning "
1979 "procedure, falling back to fixed sampling "
1980 "clock\n");
1981 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1982 ctrl &= ~SDHCI_CTRL_TUNED_CLK;
1983 ctrl &= ~SDHCI_CTRL_EXEC_TUNING;
1984 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1985
1986 err = -EIO;
1987 goto out;
1988 }
1989
1990 host->tuning_done = 0;
1991
1992 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1993 tuning_loop_counter--;
1994 timeout--;
1995 mdelay(1);
1996 } while (ctrl & SDHCI_CTRL_EXEC_TUNING);
1997
1998 /*
1999 * The Host Driver has exhausted the maximum number of loops allowed,
2000 * so use fixed sampling frequency.
2001 */
2002 if (!tuning_loop_counter || !timeout) {
2003 ctrl &= ~SDHCI_CTRL_TUNED_CLK;
2004 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2005 err = -EIO;
2006 } else {
2007 if (!(ctrl & SDHCI_CTRL_TUNED_CLK)) {
2008 pr_info(DRIVER_NAME ": Tuning procedure"
2009 " failed, falling back to fixed sampling"
2010 " clock\n");
2011 err = -EIO;
2012 }
2013 }
2014
2015out:
2016 /*
2017 * If this is the very first time we are here, we start the retuning
2018 * timer. Since only during the first time, SDHCI_NEEDS_RETUNING
2019 * flag won't be set, we check this condition before actually starting
2020 * the timer.
2021 */
2022 if (!(host->flags & SDHCI_NEEDS_RETUNING) && host->tuning_count &&
2023 (host->tuning_mode == SDHCI_TUNING_MODE_1)) {
2024 host->flags |= SDHCI_USING_RETUNING_TIMER;
2025 mod_timer(&host->tuning_timer, jiffies +
2026 host->tuning_count * HZ);
2027 /* Tuning mode 1 limits the maximum data length to 4MB */
2028 mmc->max_blk_count = (4 * 1024 * 1024) / mmc->max_blk_size;
2029 } else if (host->flags & SDHCI_USING_RETUNING_TIMER) {
2030 host->flags &= ~SDHCI_NEEDS_RETUNING;
2031 /* Reload the new initial value for timer */
2032 mod_timer(&host->tuning_timer, jiffies +
2033 host->tuning_count * HZ);
2034 }
2035
2036 /*
2037 * In case tuning fails, host controllers which support re-tuning can
2038 * try tuning again at a later time, when the re-tuning timer expires.
2039 * So for these controllers, we return 0. Since there might be other
2040 * controllers who do not have this capability, we return error for
2041 * them. SDHCI_USING_RETUNING_TIMER means the host is currently using
2042 * a retuning timer to do the retuning for the card.
2043 */
2044 if (err && (host->flags & SDHCI_USING_RETUNING_TIMER))
2045 err = 0;
2046
2047 sdhci_clear_set_irqs(host, SDHCI_INT_DATA_AVAIL, ier);
2048 spin_unlock_irqrestore(&host->lock, flags);
2049 sdhci_runtime_pm_put(host);
2050
2051 return err;
2052}
2053
2054
2055static void sdhci_enable_preset_value(struct sdhci_host *host, bool enable)
2056{
2057 u16 ctrl;
2058
2059 /* Host Controller v3.00 defines preset value registers */
2060 if (host->version < SDHCI_SPEC_300)
2061 return;
2062
2063 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2064
2065 /*
2066 * We only enable or disable Preset Value if they are not already
2067 * enabled or disabled respectively. Otherwise, we bail out.
2068 */
2069 if (enable && !(ctrl & SDHCI_CTRL_PRESET_VAL_ENABLE)) {
2070 ctrl |= SDHCI_CTRL_PRESET_VAL_ENABLE;
2071 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2072 host->flags |= SDHCI_PV_ENABLED;
2073 } else if (!enable && (ctrl & SDHCI_CTRL_PRESET_VAL_ENABLE)) {
2074 ctrl &= ~SDHCI_CTRL_PRESET_VAL_ENABLE;
2075 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2076 host->flags &= ~SDHCI_PV_ENABLED;
2077 }
2078}
2079
2080static void sdhci_card_event(struct mmc_host *mmc)
2081{
2082 struct sdhci_host *host = mmc_priv(mmc);
2083 unsigned long flags;
2084
2085 /* First check if client has provided their own card event */
2086 if (host->ops->card_event)
2087 host->ops->card_event(host);
2088
2089 spin_lock_irqsave(&host->lock, flags);
2090
2091 /* Check host->mrq first in case we are runtime suspended */
2092 if (host->mrq && !sdhci_do_get_cd(host)) {
2093 pr_err("%s: Card removed during transfer!\n",
2094 mmc_hostname(host->mmc));
2095 pr_err("%s: Resetting controller.\n",
2096 mmc_hostname(host->mmc));
2097
2098 sdhci_reset(host, SDHCI_RESET_CMD);
2099 sdhci_reset(host, SDHCI_RESET_DATA);
2100
2101 host->mrq->cmd->error = -ENOMEDIUM;
2102 tasklet_schedule(&host->finish_tasklet);
2103 }
2104
2105 spin_unlock_irqrestore(&host->lock, flags);
2106}
2107
2108static const struct mmc_host_ops sdhci_ops = {
2109 .request = sdhci_request,
2110 .set_ios = sdhci_set_ios,
2111 .get_cd = sdhci_get_cd,
2112 .get_ro = sdhci_get_ro,
2113 .hw_reset = sdhci_hw_reset,
2114 .enable_sdio_irq = sdhci_enable_sdio_irq,
2115 .start_signal_voltage_switch = sdhci_start_signal_voltage_switch,
2116 .execute_tuning = sdhci_execute_tuning,
2117 .card_event = sdhci_card_event,
2118 .card_busy = sdhci_card_busy,
2119};
2120
2121/*****************************************************************************\
2122 * *
2123 * Tasklets *
2124 * *
2125\*****************************************************************************/
2126
2127static void sdhci_tasklet_card(unsigned long param)
2128{
2129 struct sdhci_host *host = (struct sdhci_host*)param;
2130
2131 sdhci_card_event(host->mmc);
2132
2133 mmc_detect_change(host->mmc, msecs_to_jiffies(200));
2134}
2135
2136static void sdhci_tasklet_finish(unsigned long param)
2137{
2138 struct sdhci_host *host;
2139 unsigned long flags;
2140 struct mmc_request *mrq;
2141
2142 host = (struct sdhci_host*)param;
2143
2144 spin_lock_irqsave(&host->lock, flags);
2145
2146 /*
2147 * If this tasklet gets rescheduled while running, it will
2148 * be run again afterwards but without any active request.
2149 */
2150 if (!host->mrq) {
2151 spin_unlock_irqrestore(&host->lock, flags);
2152 return;
2153 }
2154
2155 del_timer(&host->timer);
2156
2157 mrq = host->mrq;
2158
2159 /*
2160 * The controller needs a reset of internal state machines
2161 * upon error conditions.
2162 */
2163 if (!(host->flags & SDHCI_DEVICE_DEAD) &&
2164 ((mrq->cmd && mrq->cmd->error) ||
2165 (mrq->data && (mrq->data->error ||
2166 (mrq->data->stop && mrq->data->stop->error))) ||
2167 (host->quirks & SDHCI_QUIRK_RESET_AFTER_REQUEST))) {
2168
2169 /* Some controllers need this kick or reset won't work here */
2170 if (host->quirks & SDHCI_QUIRK_CLOCK_BEFORE_RESET)
2171 /* This is to force an update */
2172 sdhci_update_clock(host);
2173
2174 /* Spec says we should do both at the same time, but Ricoh
2175 controllers do not like that. */
2176 sdhci_reset(host, SDHCI_RESET_CMD);
2177 sdhci_reset(host, SDHCI_RESET_DATA);
2178 }
2179
2180 host->mrq = NULL;
2181 host->cmd = NULL;
2182 host->data = NULL;
2183
2184#ifndef SDHCI_USE_LEDS_CLASS
2185 sdhci_deactivate_led(host);
2186#endif
2187
2188 mmiowb();
2189 spin_unlock_irqrestore(&host->lock, flags);
2190
2191 mmc_request_done(host->mmc, mrq);
2192 sdhci_runtime_pm_put(host);
2193}
2194
2195static void sdhci_timeout_timer(unsigned long data)
2196{
2197 struct sdhci_host *host;
2198 unsigned long flags;
2199
2200 host = (struct sdhci_host*)data;
2201
2202 spin_lock_irqsave(&host->lock, flags);
2203
2204 if (host->mrq) {
2205 pr_err("%s: Timeout waiting for hardware "
2206 "interrupt.\n", mmc_hostname(host->mmc));
2207 sdhci_dumpregs(host);
2208
2209 if (host->data) {
2210 host->data->error = -ETIMEDOUT;
2211 sdhci_finish_data(host);
2212 } else {
2213 if (host->cmd)
2214 host->cmd->error = -ETIMEDOUT;
2215 else
2216 host->mrq->cmd->error = -ETIMEDOUT;
2217
2218 tasklet_schedule(&host->finish_tasklet);
2219 }
2220 }
2221
2222 mmiowb();
2223 spin_unlock_irqrestore(&host->lock, flags);
2224}
2225
2226static void sdhci_tuning_timer(unsigned long data)
2227{
2228 struct sdhci_host *host;
2229 unsigned long flags;
2230
2231 host = (struct sdhci_host *)data;
2232
2233 spin_lock_irqsave(&host->lock, flags);
2234
2235 host->flags |= SDHCI_NEEDS_RETUNING;
2236
2237 spin_unlock_irqrestore(&host->lock, flags);
2238}
2239
2240/*****************************************************************************\
2241 * *
2242 * Interrupt handling *
2243 * *
2244\*****************************************************************************/
2245
2246static void sdhci_cmd_irq(struct sdhci_host *host, u32 intmask)
2247{
2248 BUG_ON(intmask == 0);
2249
2250 if (!host->cmd) {
2251 pr_err("%s: Got command interrupt 0x%08x even "
2252 "though no command operation was in progress.\n",
2253 mmc_hostname(host->mmc), (unsigned)intmask);
2254 sdhci_dumpregs(host);
2255 return;
2256 }
2257
2258 if (intmask & SDHCI_INT_TIMEOUT)
2259 host->cmd->error = -ETIMEDOUT;
2260 else if (intmask & (SDHCI_INT_CRC | SDHCI_INT_END_BIT |
2261 SDHCI_INT_INDEX))
2262 host->cmd->error = -EILSEQ;
2263
2264 if (host->cmd->error) {
2265 tasklet_schedule(&host->finish_tasklet);
2266 return;
2267 }
2268
2269 /*
2270 * The host can send and interrupt when the busy state has
2271 * ended, allowing us to wait without wasting CPU cycles.
2272 * Unfortunately this is overloaded on the "data complete"
2273 * interrupt, so we need to take some care when handling
2274 * it.
2275 *
2276 * Note: The 1.0 specification is a bit ambiguous about this
2277 * feature so there might be some problems with older
2278 * controllers.
2279 */
2280 if (host->cmd->flags & MMC_RSP_BUSY) {
2281 if (host->cmd->data)
2282 DBG("Cannot wait for busy signal when also "
2283 "doing a data transfer");
2284 else if (!(host->quirks & SDHCI_QUIRK_NO_BUSY_IRQ))
2285 return;
2286
2287 /* The controller does not support the end-of-busy IRQ,
2288 * fall through and take the SDHCI_INT_RESPONSE */
2289 }
2290
2291 if (intmask & SDHCI_INT_RESPONSE)
2292 sdhci_finish_command(host);
2293}
2294
2295#ifdef CONFIG_MMC_DEBUG
2296static void sdhci_show_adma_error(struct sdhci_host *host)
2297{
2298 const char *name = mmc_hostname(host->mmc);
2299 u8 *desc = host->adma_desc;
2300 __le32 *dma;
2301 __le16 *len;
2302 u8 attr;
2303
2304 sdhci_dumpregs(host);
2305
2306 while (true) {
2307 dma = (__le32 *)(desc + 4);
2308 len = (__le16 *)(desc + 2);
2309 attr = *desc;
2310
2311 DBG("%s: %p: DMA 0x%08x, LEN 0x%04x, Attr=0x%02x\n",
2312 name, desc, le32_to_cpu(*dma), le16_to_cpu(*len), attr);
2313
2314 desc += 8;
2315
2316 if (attr & 2)
2317 break;
2318 }
2319}
2320#else
2321static void sdhci_show_adma_error(struct sdhci_host *host) { }
2322#endif
2323
2324static void sdhci_data_irq(struct sdhci_host *host, u32 intmask)
2325{
2326 u32 command;
2327 BUG_ON(intmask == 0);
2328
2329 /* CMD19 generates _only_ Buffer Read Ready interrupt */
2330 if (intmask & SDHCI_INT_DATA_AVAIL) {
2331 command = SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND));
2332 if (command == MMC_SEND_TUNING_BLOCK ||
2333 command == MMC_SEND_TUNING_BLOCK_HS200) {
2334 host->tuning_done = 1;
2335 wake_up(&host->buf_ready_int);
2336 return;
2337 }
2338 }
2339
2340 if (!host->data) {
2341 /*
2342 * The "data complete" interrupt is also used to
2343 * indicate that a busy state has ended. See comment
2344 * above in sdhci_cmd_irq().
2345 */
2346 if (host->cmd && (host->cmd->flags & MMC_RSP_BUSY)) {
2347 if (intmask & SDHCI_INT_DATA_END) {
2348 sdhci_finish_command(host);
2349 return;
2350 }
2351 }
2352
2353 pr_err("%s: Got data interrupt 0x%08x even "
2354 "though no data operation was in progress.\n",
2355 mmc_hostname(host->mmc), (unsigned)intmask);
2356 sdhci_dumpregs(host);
2357
2358 return;
2359 }
2360
2361 if (intmask & SDHCI_INT_DATA_TIMEOUT)
2362 host->data->error = -ETIMEDOUT;
2363 else if (intmask & SDHCI_INT_DATA_END_BIT)
2364 host->data->error = -EILSEQ;
2365 else if ((intmask & SDHCI_INT_DATA_CRC) &&
2366 SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND))
2367 != MMC_BUS_TEST_R)
2368 host->data->error = -EILSEQ;
2369 else if (intmask & SDHCI_INT_ADMA_ERROR) {
2370 pr_err("%s: ADMA error\n", mmc_hostname(host->mmc));
2371 sdhci_show_adma_error(host);
2372 host->data->error = -EIO;
2373 if (host->ops->adma_workaround)
2374 host->ops->adma_workaround(host, intmask);
2375 }
2376
2377 if (host->data->error)
2378 sdhci_finish_data(host);
2379 else {
2380 if (intmask & (SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL))
2381 sdhci_transfer_pio(host);
2382
2383 /*
2384 * We currently don't do anything fancy with DMA
2385 * boundaries, but as we can't disable the feature
2386 * we need to at least restart the transfer.
2387 *
2388 * According to the spec sdhci_readl(host, SDHCI_DMA_ADDRESS)
2389 * should return a valid address to continue from, but as
2390 * some controllers are faulty, don't trust them.
2391 */
2392 if (intmask & SDHCI_INT_DMA_END) {
2393 u32 dmastart, dmanow;
2394 dmastart = sg_dma_address(host->data->sg);
2395 dmanow = dmastart + host->data->bytes_xfered;
2396 /*
2397 * Force update to the next DMA block boundary.
2398 */
2399 dmanow = (dmanow &
2400 ~(SDHCI_DEFAULT_BOUNDARY_SIZE - 1)) +
2401 SDHCI_DEFAULT_BOUNDARY_SIZE;
2402 host->data->bytes_xfered = dmanow - dmastart;
2403 DBG("%s: DMA base 0x%08x, transferred 0x%06x bytes,"
2404 " next 0x%08x\n",
2405 mmc_hostname(host->mmc), dmastart,
2406 host->data->bytes_xfered, dmanow);
2407 sdhci_writel(host, dmanow, SDHCI_DMA_ADDRESS);
2408 }
2409
2410 if (intmask & SDHCI_INT_DATA_END) {
2411 if (host->cmd) {
2412 /*
2413 * Data managed to finish before the
2414 * command completed. Make sure we do
2415 * things in the proper order.
2416 */
2417 host->data_early = 1;
2418 } else {
2419 sdhci_finish_data(host);
2420 }
2421 }
2422 }
2423}
2424
2425static irqreturn_t sdhci_irq(int irq, void *dev_id)
2426{
2427 irqreturn_t result;
2428 struct sdhci_host *host = dev_id;
2429 u32 intmask, unexpected = 0;
2430 int cardint = 0, max_loops = 16;
2431
2432 spin_lock(&host->lock);
2433
2434 if (host->runtime_suspended) {
2435 spin_unlock(&host->lock);
2436 return IRQ_NONE;
2437 }
2438
2439 intmask = sdhci_readl(host, SDHCI_INT_STATUS);
2440
2441 if (!intmask || intmask == 0xffffffff) {
2442 result = IRQ_NONE;
2443 goto out;
2444 }
2445
2446again:
2447 DBG("*** %s got interrupt: 0x%08x\n",
2448 mmc_hostname(host->mmc), intmask);
2449
2450 if (intmask & (SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE)) {
2451 u32 present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
2452 SDHCI_CARD_PRESENT;
2453
2454 /*
2455 * There is a observation on i.mx esdhc. INSERT bit will be
2456 * immediately set again when it gets cleared, if a card is
2457 * inserted. We have to mask the irq to prevent interrupt
2458 * storm which will freeze the system. And the REMOVE gets
2459 * the same situation.
2460 *
2461 * More testing are needed here to ensure it works for other
2462 * platforms though.
2463 */
2464 sdhci_mask_irqs(host, present ? SDHCI_INT_CARD_INSERT :
2465 SDHCI_INT_CARD_REMOVE);
2466 sdhci_unmask_irqs(host, present ? SDHCI_INT_CARD_REMOVE :
2467 SDHCI_INT_CARD_INSERT);
2468
2469 sdhci_writel(host, intmask & (SDHCI_INT_CARD_INSERT |
2470 SDHCI_INT_CARD_REMOVE), SDHCI_INT_STATUS);
2471 intmask &= ~(SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE);
2472 tasklet_schedule(&host->card_tasklet);
2473 }
2474
2475 if (intmask & SDHCI_INT_CMD_MASK) {
2476 sdhci_writel(host, intmask & SDHCI_INT_CMD_MASK,
2477 SDHCI_INT_STATUS);
2478 sdhci_cmd_irq(host, intmask & SDHCI_INT_CMD_MASK);
2479 }
2480
2481 if (intmask & SDHCI_INT_DATA_MASK) {
2482 sdhci_writel(host, intmask & SDHCI_INT_DATA_MASK,
2483 SDHCI_INT_STATUS);
2484 sdhci_data_irq(host, intmask & SDHCI_INT_DATA_MASK);
2485 }
2486
2487 intmask &= ~(SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK);
2488
2489 intmask &= ~SDHCI_INT_ERROR;
2490
2491 if (intmask & SDHCI_INT_BUS_POWER) {
2492 pr_err("%s: Card is consuming too much power!\n",
2493 mmc_hostname(host->mmc));
2494 sdhci_writel(host, SDHCI_INT_BUS_POWER, SDHCI_INT_STATUS);
2495 }
2496
2497 intmask &= ~SDHCI_INT_BUS_POWER;
2498
2499 if (intmask & SDHCI_INT_CARD_INT)
2500 cardint = 1;
2501
2502 intmask &= ~SDHCI_INT_CARD_INT;
2503
2504 if (intmask) {
2505 unexpected |= intmask;
2506 sdhci_writel(host, intmask, SDHCI_INT_STATUS);
2507 }
2508
2509 result = IRQ_HANDLED;
2510
2511 intmask = sdhci_readl(host, SDHCI_INT_STATUS);
2512
2513 /*
2514 * If we know we'll call the driver to signal SDIO IRQ, disregard
2515 * further indications of Card Interrupt in the status to avoid a
2516 * needless loop.
2517 */
2518 if (cardint)
2519 intmask &= ~SDHCI_INT_CARD_INT;
2520 if (intmask && --max_loops)
2521 goto again;
2522out:
2523 spin_unlock(&host->lock);
2524
2525 if (unexpected) {
2526 pr_err("%s: Unexpected interrupt 0x%08x.\n",
2527 mmc_hostname(host->mmc), unexpected);
2528 sdhci_dumpregs(host);
2529 }
2530 /*
2531 * We have to delay this as it calls back into the driver.
2532 */
2533 if (cardint)
2534 mmc_signal_sdio_irq(host->mmc);
2535
2536 return result;
2537}
2538
2539/*****************************************************************************\
2540 * *
2541 * Suspend/resume *
2542 * *
2543\*****************************************************************************/
2544
2545#ifdef CONFIG_PM
2546void sdhci_enable_irq_wakeups(struct sdhci_host *host)
2547{
2548 u8 val;
2549 u8 mask = SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE
2550 | SDHCI_WAKE_ON_INT;
2551
2552 val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
2553 val |= mask ;
2554 /* Avoid fake wake up */
2555 if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
2556 val &= ~(SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE);
2557 sdhci_writeb(host, val, SDHCI_WAKE_UP_CONTROL);
2558}
2559EXPORT_SYMBOL_GPL(sdhci_enable_irq_wakeups);
2560
2561void sdhci_disable_irq_wakeups(struct sdhci_host *host)
2562{
2563 u8 val;
2564 u8 mask = SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE
2565 | SDHCI_WAKE_ON_INT;
2566
2567 val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
2568 val &= ~mask;
2569 sdhci_writeb(host, val, SDHCI_WAKE_UP_CONTROL);
2570}
2571EXPORT_SYMBOL_GPL(sdhci_disable_irq_wakeups);
2572
2573int sdhci_suspend_host(struct sdhci_host *host)
2574{
2575 if (host->ops->platform_suspend)
2576 host->ops->platform_suspend(host);
2577
2578 sdhci_disable_card_detection(host);
2579
2580 /* Disable tuning since we are suspending */
2581 if (host->flags & SDHCI_USING_RETUNING_TIMER) {
2582 del_timer_sync(&host->tuning_timer);
2583 host->flags &= ~SDHCI_NEEDS_RETUNING;
2584 }
2585
2586 if (!device_may_wakeup(mmc_dev(host->mmc))) {
2587 sdhci_mask_irqs(host, SDHCI_INT_ALL_MASK);
2588 free_irq(host->irq, host);
2589 } else {
2590 sdhci_enable_irq_wakeups(host);
2591 enable_irq_wake(host->irq);
2592 }
2593 return 0;
2594}
2595
2596EXPORT_SYMBOL_GPL(sdhci_suspend_host);
2597
2598int sdhci_resume_host(struct sdhci_host *host)
2599{
2600 int ret = 0;
2601
2602 if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
2603 if (host->ops->enable_dma)
2604 host->ops->enable_dma(host);
2605 }
2606
2607 if (!device_may_wakeup(mmc_dev(host->mmc))) {
2608 ret = request_irq(host->irq, sdhci_irq, IRQF_SHARED,
2609 mmc_hostname(host->mmc), host);
2610 if (ret)
2611 return ret;
2612 } else {
2613 sdhci_disable_irq_wakeups(host);
2614 disable_irq_wake(host->irq);
2615 }
2616
2617 if ((host->mmc->pm_flags & MMC_PM_KEEP_POWER) &&
2618 (host->quirks2 & SDHCI_QUIRK2_HOST_OFF_CARD_ON)) {
2619 /* Card keeps power but host controller does not */
2620 sdhci_init(host, 0);
2621 host->pwr = 0;
2622 host->clock = 0;
2623 sdhci_do_set_ios(host, &host->mmc->ios);
2624 } else {
2625 sdhci_init(host, (host->mmc->pm_flags & MMC_PM_KEEP_POWER));
2626 mmiowb();
2627 }
2628
2629 sdhci_enable_card_detection(host);
2630
2631 if (host->ops->platform_resume)
2632 host->ops->platform_resume(host);
2633
2634 /* Set the re-tuning expiration flag */
2635 if (host->flags & SDHCI_USING_RETUNING_TIMER)
2636 host->flags |= SDHCI_NEEDS_RETUNING;
2637
2638 return ret;
2639}
2640
2641EXPORT_SYMBOL_GPL(sdhci_resume_host);
2642#endif /* CONFIG_PM */
2643
2644#ifdef CONFIG_PM_RUNTIME
2645
2646static int sdhci_runtime_pm_get(struct sdhci_host *host)
2647{
2648 return pm_runtime_get_sync(host->mmc->parent);
2649}
2650
2651static int sdhci_runtime_pm_put(struct sdhci_host *host)
2652{
2653 pm_runtime_mark_last_busy(host->mmc->parent);
2654 return pm_runtime_put_autosuspend(host->mmc->parent);
2655}
2656
2657static void sdhci_runtime_pm_bus_on(struct sdhci_host *host)
2658{
2659 if (host->runtime_suspended || host->bus_on)
2660 return;
2661 host->bus_on = true;
2662 pm_runtime_get_noresume(host->mmc->parent);
2663}
2664
2665static void sdhci_runtime_pm_bus_off(struct sdhci_host *host)
2666{
2667 if (host->runtime_suspended || !host->bus_on)
2668 return;
2669 host->bus_on = false;
2670 pm_runtime_put_noidle(host->mmc->parent);
2671}
2672
2673int sdhci_runtime_suspend_host(struct sdhci_host *host)
2674{
2675 unsigned long flags;
2676 int ret = 0;
2677
2678 /* Disable tuning since we are suspending */
2679 if (host->flags & SDHCI_USING_RETUNING_TIMER) {
2680 del_timer_sync(&host->tuning_timer);
2681 host->flags &= ~SDHCI_NEEDS_RETUNING;
2682 }
2683
2684 spin_lock_irqsave(&host->lock, flags);
2685 sdhci_mask_irqs(host, SDHCI_INT_ALL_MASK);
2686 spin_unlock_irqrestore(&host->lock, flags);
2687
2688 synchronize_irq(host->irq);
2689
2690 spin_lock_irqsave(&host->lock, flags);
2691 host->runtime_suspended = true;
2692 spin_unlock_irqrestore(&host->lock, flags);
2693
2694 return ret;
2695}
2696EXPORT_SYMBOL_GPL(sdhci_runtime_suspend_host);
2697
2698int sdhci_runtime_resume_host(struct sdhci_host *host)
2699{
2700 unsigned long flags;
2701 int ret = 0, host_flags = host->flags;
2702
2703 if (host_flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
2704 if (host->ops->enable_dma)
2705 host->ops->enable_dma(host);
2706 }
2707
2708 sdhci_init(host, 0);
2709
2710 /* Force clock and power re-program */
2711 host->pwr = 0;
2712 host->clock = 0;
2713 sdhci_do_set_ios(host, &host->mmc->ios);
2714
2715 sdhci_do_start_signal_voltage_switch(host, &host->mmc->ios);
2716 if ((host_flags & SDHCI_PV_ENABLED) &&
2717 !(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN)) {
2718 spin_lock_irqsave(&host->lock, flags);
2719 sdhci_enable_preset_value(host, true);
2720 spin_unlock_irqrestore(&host->lock, flags);
2721 }
2722
2723 /* Set the re-tuning expiration flag */
2724 if (host->flags & SDHCI_USING_RETUNING_TIMER)
2725 host->flags |= SDHCI_NEEDS_RETUNING;
2726
2727 spin_lock_irqsave(&host->lock, flags);
2728
2729 host->runtime_suspended = false;
2730
2731 /* Enable SDIO IRQ */
2732 if ((host->flags & SDHCI_SDIO_IRQ_ENABLED))
2733 sdhci_enable_sdio_irq_nolock(host, true);
2734
2735 /* Enable Card Detection */
2736 sdhci_enable_card_detection(host);
2737
2738 spin_unlock_irqrestore(&host->lock, flags);
2739
2740 return ret;
2741}
2742EXPORT_SYMBOL_GPL(sdhci_runtime_resume_host);
2743
2744#endif
2745
2746/*****************************************************************************\
2747 * *
2748 * Device allocation/registration *
2749 * *
2750\*****************************************************************************/
2751
2752struct sdhci_host *sdhci_alloc_host(struct device *dev,
2753 size_t priv_size)
2754{
2755 struct mmc_host *mmc;
2756 struct sdhci_host *host;
2757
2758 WARN_ON(dev == NULL);
2759
2760 mmc = mmc_alloc_host(sizeof(struct sdhci_host) + priv_size, dev);
2761 if (!mmc)
2762 return ERR_PTR(-ENOMEM);
2763
2764 host = mmc_priv(mmc);
2765 host->mmc = mmc;
2766
2767 return host;
2768}
2769
2770EXPORT_SYMBOL_GPL(sdhci_alloc_host);
2771
2772int sdhci_add_host(struct sdhci_host *host)
2773{
2774 struct mmc_host *mmc;
2775 u32 caps[2] = {0, 0};
2776 u32 max_current_caps;
2777 unsigned int ocr_avail;
2778 int ret;
2779
2780 WARN_ON(host == NULL);
2781 if (host == NULL)
2782 return -EINVAL;
2783
2784 mmc = host->mmc;
2785
2786 if (debug_quirks)
2787 host->quirks = debug_quirks;
2788 if (debug_quirks2)
2789 host->quirks2 = debug_quirks2;
2790
2791 sdhci_reset(host, SDHCI_RESET_ALL);
2792
2793 host->version = sdhci_readw(host, SDHCI_HOST_VERSION);
2794 host->version = (host->version & SDHCI_SPEC_VER_MASK)
2795 >> SDHCI_SPEC_VER_SHIFT;
2796 if (host->version > SDHCI_SPEC_300) {
2797 pr_err("%s: Unknown controller version (%d). "
2798 "You may experience problems.\n", mmc_hostname(mmc),
2799 host->version);
2800 }
2801
2802 caps[0] = (host->quirks & SDHCI_QUIRK_MISSING_CAPS) ? host->caps :
2803 sdhci_readl(host, SDHCI_CAPABILITIES);
2804
2805 if (host->version >= SDHCI_SPEC_300)
2806 caps[1] = (host->quirks & SDHCI_QUIRK_MISSING_CAPS) ?
2807 host->caps1 :
2808 sdhci_readl(host, SDHCI_CAPABILITIES_1);
2809
2810 if (host->quirks & SDHCI_QUIRK_FORCE_DMA)
2811 host->flags |= SDHCI_USE_SDMA;
2812 else if (!(caps[0] & SDHCI_CAN_DO_SDMA))
2813 DBG("Controller doesn't have SDMA capability\n");
2814 else
2815 host->flags |= SDHCI_USE_SDMA;
2816
2817 if ((host->quirks & SDHCI_QUIRK_BROKEN_DMA) &&
2818 (host->flags & SDHCI_USE_SDMA)) {
2819 DBG("Disabling DMA as it is marked broken\n");
2820 host->flags &= ~SDHCI_USE_SDMA;
2821 }
2822
2823 if ((host->version >= SDHCI_SPEC_200) &&
2824 (caps[0] & SDHCI_CAN_DO_ADMA2))
2825 host->flags |= SDHCI_USE_ADMA;
2826
2827 if ((host->quirks & SDHCI_QUIRK_BROKEN_ADMA) &&
2828 (host->flags & SDHCI_USE_ADMA)) {
2829 DBG("Disabling ADMA as it is marked broken\n");
2830 host->flags &= ~SDHCI_USE_ADMA;
2831 }
2832
2833 if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
2834 if (host->ops->enable_dma) {
2835 if (host->ops->enable_dma(host)) {
2836 pr_warning("%s: No suitable DMA "
2837 "available. Falling back to PIO.\n",
2838 mmc_hostname(mmc));
2839 host->flags &=
2840 ~(SDHCI_USE_SDMA | SDHCI_USE_ADMA);
2841 }
2842 }
2843 }
2844
2845 if (host->flags & SDHCI_USE_ADMA) {
2846 /*
2847 * We need to allocate descriptors for all sg entries
2848 * (128) and potentially one alignment transfer for
2849 * each of those entries.
2850 */
2851 host->adma_desc = kmalloc((128 * 2 + 1) * 4, GFP_KERNEL);
2852 host->align_buffer = kmalloc(128 * 4, GFP_KERNEL);
2853 if (!host->adma_desc || !host->align_buffer) {
2854 kfree(host->adma_desc);
2855 kfree(host->align_buffer);
2856 pr_warning("%s: Unable to allocate ADMA "
2857 "buffers. Falling back to standard DMA.\n",
2858 mmc_hostname(mmc));
2859 host->flags &= ~SDHCI_USE_ADMA;
2860 }
2861 }
2862
2863 /*
2864 * If we use DMA, then it's up to the caller to set the DMA
2865 * mask, but PIO does not need the hw shim so we set a new
2866 * mask here in that case.
2867 */
2868 if (!(host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA))) {
2869 host->dma_mask = DMA_BIT_MASK(64);
2870 mmc_dev(host->mmc)->dma_mask = &host->dma_mask;
2871 }
2872
2873 if (host->version >= SDHCI_SPEC_300)
2874 host->max_clk = (caps[0] & SDHCI_CLOCK_V3_BASE_MASK)
2875 >> SDHCI_CLOCK_BASE_SHIFT;
2876 else
2877 host->max_clk = (caps[0] & SDHCI_CLOCK_BASE_MASK)
2878 >> SDHCI_CLOCK_BASE_SHIFT;
2879
2880 host->max_clk *= 1000000;
2881 if (host->max_clk == 0 || host->quirks &
2882 SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN) {
2883 if (!host->ops->get_max_clock) {
2884 pr_err("%s: Hardware doesn't specify base clock "
2885 "frequency.\n", mmc_hostname(mmc));
2886 return -ENODEV;
2887 }
2888 host->max_clk = host->ops->get_max_clock(host);
2889 }
2890
2891 /*
2892 * In case of Host Controller v3.00, find out whether clock
2893 * multiplier is supported.
2894 */
2895 host->clk_mul = (caps[1] & SDHCI_CLOCK_MUL_MASK) >>
2896 SDHCI_CLOCK_MUL_SHIFT;
2897
2898 /*
2899 * In case the value in Clock Multiplier is 0, then programmable
2900 * clock mode is not supported, otherwise the actual clock
2901 * multiplier is one more than the value of Clock Multiplier
2902 * in the Capabilities Register.
2903 */
2904 if (host->clk_mul)
2905 host->clk_mul += 1;
2906
2907 /*
2908 * Set host parameters.
2909 */
2910 mmc->ops = &sdhci_ops;
2911 mmc->f_max = host->max_clk;
2912 if (host->ops->get_min_clock)
2913 mmc->f_min = host->ops->get_min_clock(host);
2914 else if (host->version >= SDHCI_SPEC_300) {
2915 if (host->clk_mul) {
2916 mmc->f_min = (host->max_clk * host->clk_mul) / 1024;
2917 mmc->f_max = host->max_clk * host->clk_mul;
2918 } else
2919 mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_300;
2920 } else
2921 mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_200;
2922
2923 host->timeout_clk =
2924 (caps[0] & SDHCI_TIMEOUT_CLK_MASK) >> SDHCI_TIMEOUT_CLK_SHIFT;
2925 if (host->timeout_clk == 0) {
2926 if (host->ops->get_timeout_clock) {
2927 host->timeout_clk = host->ops->get_timeout_clock(host);
2928 } else if (!(host->quirks &
2929 SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK)) {
2930 pr_err("%s: Hardware doesn't specify timeout clock "
2931 "frequency.\n", mmc_hostname(mmc));
2932 return -ENODEV;
2933 }
2934 }
2935 if (caps[0] & SDHCI_TIMEOUT_CLK_UNIT)
2936 host->timeout_clk *= 1000;
2937
2938 if (host->quirks & SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK)
2939 host->timeout_clk = mmc->f_max / 1000;
2940
2941 mmc->max_busy_timeout = (1 << 27) / host->timeout_clk;
2942
2943 mmc->caps |= MMC_CAP_SDIO_IRQ | MMC_CAP_ERASE | MMC_CAP_CMD23;
2944
2945 if (host->quirks & SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12)
2946 host->flags |= SDHCI_AUTO_CMD12;
2947
2948 /* Auto-CMD23 stuff only works in ADMA or PIO. */
2949 if ((host->version >= SDHCI_SPEC_300) &&
2950 ((host->flags & SDHCI_USE_ADMA) ||
2951 !(host->flags & SDHCI_USE_SDMA))) {
2952 host->flags |= SDHCI_AUTO_CMD23;
2953 DBG("%s: Auto-CMD23 available\n", mmc_hostname(mmc));
2954 } else {
2955 DBG("%s: Auto-CMD23 unavailable\n", mmc_hostname(mmc));
2956 }
2957
2958 /*
2959 * A controller may support 8-bit width, but the board itself
2960 * might not have the pins brought out. Boards that support
2961 * 8-bit width must set "mmc->caps |= MMC_CAP_8_BIT_DATA;" in
2962 * their platform code before calling sdhci_add_host(), and we
2963 * won't assume 8-bit width for hosts without that CAP.
2964 */
2965 if (!(host->quirks & SDHCI_QUIRK_FORCE_1_BIT_DATA))
2966 mmc->caps |= MMC_CAP_4_BIT_DATA;
2967
2968 if (host->quirks2 & SDHCI_QUIRK2_HOST_NO_CMD23)
2969 mmc->caps &= ~MMC_CAP_CMD23;
2970
2971 if (caps[0] & SDHCI_CAN_DO_HISPD)
2972 mmc->caps |= MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED;
2973
2974 if ((host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) &&
2975 !(host->mmc->caps & MMC_CAP_NONREMOVABLE))
2976 mmc->caps |= MMC_CAP_NEEDS_POLL;
2977
2978 /* If vqmmc regulator and no 1.8V signalling, then there's no UHS */
2979 host->vqmmc = regulator_get_optional(mmc_dev(mmc), "vqmmc");
2980 if (IS_ERR_OR_NULL(host->vqmmc)) {
2981 if (PTR_ERR(host->vqmmc) < 0) {
2982 pr_info("%s: no vqmmc regulator found\n",
2983 mmc_hostname(mmc));
2984 host->vqmmc = NULL;
2985 }
2986 } else {
2987 ret = regulator_enable(host->vqmmc);
2988 if (!regulator_is_supported_voltage(host->vqmmc, 1700000,
2989 1950000))
2990 caps[1] &= ~(SDHCI_SUPPORT_SDR104 |
2991 SDHCI_SUPPORT_SDR50 |
2992 SDHCI_SUPPORT_DDR50);
2993 if (ret) {
2994 pr_warn("%s: Failed to enable vqmmc regulator: %d\n",
2995 mmc_hostname(mmc), ret);
2996 host->vqmmc = NULL;
2997 }
2998 }
2999
3000 if (host->quirks2 & SDHCI_QUIRK2_NO_1_8_V)
3001 caps[1] &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 |
3002 SDHCI_SUPPORT_DDR50);
3003
3004 /* Any UHS-I mode in caps implies SDR12 and SDR25 support. */
3005 if (caps[1] & (SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 |
3006 SDHCI_SUPPORT_DDR50))
3007 mmc->caps |= MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25;
3008
3009 /* SDR104 supports also implies SDR50 support */
3010 if (caps[1] & SDHCI_SUPPORT_SDR104) {
3011 mmc->caps |= MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_SDR50;
3012 /* SD3.0: SDR104 is supported so (for eMMC) the caps2
3013 * field can be promoted to support HS200.
3014 */
3015 if (!(host->quirks2 & SDHCI_QUIRK2_BROKEN_HS200))
3016 mmc->caps2 |= MMC_CAP2_HS200;
3017 } else if (caps[1] & SDHCI_SUPPORT_SDR50)
3018 mmc->caps |= MMC_CAP_UHS_SDR50;
3019
3020 if ((caps[1] & SDHCI_SUPPORT_DDR50) &&
3021 !(host->quirks2 & SDHCI_QUIRK2_BROKEN_DDR50))
3022 mmc->caps |= MMC_CAP_UHS_DDR50;
3023
3024 /* Does the host need tuning for SDR50? */
3025 if (caps[1] & SDHCI_USE_SDR50_TUNING)
3026 host->flags |= SDHCI_SDR50_NEEDS_TUNING;
3027
3028 /* Does the host need tuning for SDR104 / HS200? */
3029 if (mmc->caps2 & MMC_CAP2_HS200)
3030 host->flags |= SDHCI_SDR104_NEEDS_TUNING;
3031
3032 /* Driver Type(s) (A, C, D) supported by the host */
3033 if (caps[1] & SDHCI_DRIVER_TYPE_A)
3034 mmc->caps |= MMC_CAP_DRIVER_TYPE_A;
3035 if (caps[1] & SDHCI_DRIVER_TYPE_C)
3036 mmc->caps |= MMC_CAP_DRIVER_TYPE_C;
3037 if (caps[1] & SDHCI_DRIVER_TYPE_D)
3038 mmc->caps |= MMC_CAP_DRIVER_TYPE_D;
3039
3040 /* Initial value for re-tuning timer count */
3041 host->tuning_count = (caps[1] & SDHCI_RETUNING_TIMER_COUNT_MASK) >>
3042 SDHCI_RETUNING_TIMER_COUNT_SHIFT;
3043
3044 /*
3045 * In case Re-tuning Timer is not disabled, the actual value of
3046 * re-tuning timer will be 2 ^ (n - 1).
3047 */
3048 if (host->tuning_count)
3049 host->tuning_count = 1 << (host->tuning_count - 1);
3050
3051 /* Re-tuning mode supported by the Host Controller */
3052 host->tuning_mode = (caps[1] & SDHCI_RETUNING_MODE_MASK) >>
3053 SDHCI_RETUNING_MODE_SHIFT;
3054
3055 ocr_avail = 0;
3056
3057 host->vmmc = regulator_get_optional(mmc_dev(mmc), "vmmc");
3058 if (IS_ERR_OR_NULL(host->vmmc)) {
3059 if (PTR_ERR(host->vmmc) < 0) {
3060 pr_info("%s: no vmmc regulator found\n",
3061 mmc_hostname(mmc));
3062 host->vmmc = NULL;
3063 }
3064 }
3065
3066#ifdef CONFIG_REGULATOR
3067 /*
3068 * Voltage range check makes sense only if regulator reports
3069 * any voltage value.
3070 */
3071 if (host->vmmc && regulator_get_voltage(host->vmmc) > 0) {
3072 ret = regulator_is_supported_voltage(host->vmmc, 2700000,
3073 3600000);
3074 if ((ret <= 0) || (!(caps[0] & SDHCI_CAN_VDD_330)))
3075 caps[0] &= ~SDHCI_CAN_VDD_330;
3076 if ((ret <= 0) || (!(caps[0] & SDHCI_CAN_VDD_300)))
3077 caps[0] &= ~SDHCI_CAN_VDD_300;
3078 ret = regulator_is_supported_voltage(host->vmmc, 1700000,
3079 1950000);
3080 if ((ret <= 0) || (!(caps[0] & SDHCI_CAN_VDD_180)))
3081 caps[0] &= ~SDHCI_CAN_VDD_180;
3082 }
3083#endif /* CONFIG_REGULATOR */
3084
3085 /*
3086 * According to SD Host Controller spec v3.00, if the Host System
3087 * can afford more than 150mA, Host Driver should set XPC to 1. Also
3088 * the value is meaningful only if Voltage Support in the Capabilities
3089 * register is set. The actual current value is 4 times the register
3090 * value.
3091 */
3092 max_current_caps = sdhci_readl(host, SDHCI_MAX_CURRENT);
3093 if (!max_current_caps && host->vmmc) {
3094 u32 curr = regulator_get_current_limit(host->vmmc);
3095 if (curr > 0) {
3096
3097 /* convert to SDHCI_MAX_CURRENT format */
3098 curr = curr/1000; /* convert to mA */
3099 curr = curr/SDHCI_MAX_CURRENT_MULTIPLIER;
3100
3101 curr = min_t(u32, curr, SDHCI_MAX_CURRENT_LIMIT);
3102 max_current_caps =
3103 (curr << SDHCI_MAX_CURRENT_330_SHIFT) |
3104 (curr << SDHCI_MAX_CURRENT_300_SHIFT) |
3105 (curr << SDHCI_MAX_CURRENT_180_SHIFT);
3106 }
3107 }
3108
3109 if (caps[0] & SDHCI_CAN_VDD_330) {
3110 ocr_avail |= MMC_VDD_32_33 | MMC_VDD_33_34;
3111
3112 mmc->max_current_330 = ((max_current_caps &
3113 SDHCI_MAX_CURRENT_330_MASK) >>
3114 SDHCI_MAX_CURRENT_330_SHIFT) *
3115 SDHCI_MAX_CURRENT_MULTIPLIER;
3116 }
3117 if (caps[0] & SDHCI_CAN_VDD_300) {
3118 ocr_avail |= MMC_VDD_29_30 | MMC_VDD_30_31;
3119
3120 mmc->max_current_300 = ((max_current_caps &
3121 SDHCI_MAX_CURRENT_300_MASK) >>
3122 SDHCI_MAX_CURRENT_300_SHIFT) *
3123 SDHCI_MAX_CURRENT_MULTIPLIER;
3124 }
3125 if (caps[0] & SDHCI_CAN_VDD_180) {
3126 ocr_avail |= MMC_VDD_165_195;
3127
3128 mmc->max_current_180 = ((max_current_caps &
3129 SDHCI_MAX_CURRENT_180_MASK) >>
3130 SDHCI_MAX_CURRENT_180_SHIFT) *
3131 SDHCI_MAX_CURRENT_MULTIPLIER;
3132 }
3133
3134 if (host->ocr_mask)
3135 ocr_avail = host->ocr_mask;
3136
3137 mmc->ocr_avail = ocr_avail;
3138 mmc->ocr_avail_sdio = ocr_avail;
3139 if (host->ocr_avail_sdio)
3140 mmc->ocr_avail_sdio &= host->ocr_avail_sdio;
3141 mmc->ocr_avail_sd = ocr_avail;
3142 if (host->ocr_avail_sd)
3143 mmc->ocr_avail_sd &= host->ocr_avail_sd;
3144 else /* normal SD controllers don't support 1.8V */
3145 mmc->ocr_avail_sd &= ~MMC_VDD_165_195;
3146 mmc->ocr_avail_mmc = ocr_avail;
3147 if (host->ocr_avail_mmc)
3148 mmc->ocr_avail_mmc &= host->ocr_avail_mmc;
3149
3150 if (mmc->ocr_avail == 0) {
3151 pr_err("%s: Hardware doesn't report any "
3152 "support voltages.\n", mmc_hostname(mmc));
3153 return -ENODEV;
3154 }
3155
3156 spin_lock_init(&host->lock);
3157
3158 /*
3159 * Maximum number of segments. Depends on if the hardware
3160 * can do scatter/gather or not.
3161 */
3162 if (host->flags & SDHCI_USE_ADMA)
3163 mmc->max_segs = 128;
3164 else if (host->flags & SDHCI_USE_SDMA)
3165 mmc->max_segs = 1;
3166 else /* PIO */
3167 mmc->max_segs = 128;
3168
3169 /*
3170 * Maximum number of sectors in one transfer. Limited by DMA boundary
3171 * size (512KiB).
3172 */
3173 mmc->max_req_size = 524288;
3174
3175 /*
3176 * Maximum segment size. Could be one segment with the maximum number
3177 * of bytes. When doing hardware scatter/gather, each entry cannot
3178 * be larger than 64 KiB though.
3179 */
3180 if (host->flags & SDHCI_USE_ADMA) {
3181 if (host->quirks & SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC)
3182 mmc->max_seg_size = 65535;
3183 else
3184 mmc->max_seg_size = 65536;
3185 } else {
3186 mmc->max_seg_size = mmc->max_req_size;
3187 }
3188
3189 /*
3190 * Maximum block size. This varies from controller to controller and
3191 * is specified in the capabilities register.
3192 */
3193 if (host->quirks & SDHCI_QUIRK_FORCE_BLK_SZ_2048) {
3194 mmc->max_blk_size = 2;
3195 } else {
3196 mmc->max_blk_size = (caps[0] & SDHCI_MAX_BLOCK_MASK) >>
3197 SDHCI_MAX_BLOCK_SHIFT;
3198 if (mmc->max_blk_size >= 3) {
3199 pr_warning("%s: Invalid maximum block size, "
3200 "assuming 512 bytes\n", mmc_hostname(mmc));
3201 mmc->max_blk_size = 0;
3202 }
3203 }
3204
3205 mmc->max_blk_size = 512 << mmc->max_blk_size;
3206
3207 /*
3208 * Maximum block count.
3209 */
3210 mmc->max_blk_count = (host->quirks & SDHCI_QUIRK_NO_MULTIBLOCK) ? 1 : 65535;
3211
3212 /*
3213 * Init tasklets.
3214 */
3215 tasklet_init(&host->card_tasklet,
3216 sdhci_tasklet_card, (unsigned long)host);
3217 tasklet_init(&host->finish_tasklet,
3218 sdhci_tasklet_finish, (unsigned long)host);
3219
3220 setup_timer(&host->timer, sdhci_timeout_timer, (unsigned long)host);
3221
3222 if (host->version >= SDHCI_SPEC_300) {
3223 init_waitqueue_head(&host->buf_ready_int);
3224
3225 /* Initialize re-tuning timer */
3226 init_timer(&host->tuning_timer);
3227 host->tuning_timer.data = (unsigned long)host;
3228 host->tuning_timer.function = sdhci_tuning_timer;
3229 }
3230
3231 sdhci_init(host, 0);
3232
3233 ret = request_irq(host->irq, sdhci_irq, IRQF_SHARED,
3234 mmc_hostname(mmc), host);
3235 if (ret) {
3236 pr_err("%s: Failed to request IRQ %d: %d\n",
3237 mmc_hostname(mmc), host->irq, ret);
3238 goto untasklet;
3239 }
3240
3241#ifdef CONFIG_MMC_DEBUG
3242 sdhci_dumpregs(host);
3243#endif
3244
3245#ifdef SDHCI_USE_LEDS_CLASS
3246 snprintf(host->led_name, sizeof(host->led_name),
3247 "%s::", mmc_hostname(mmc));
3248 host->led.name = host->led_name;
3249 host->led.brightness = LED_OFF;
3250 host->led.default_trigger = mmc_hostname(mmc);
3251 host->led.brightness_set = sdhci_led_control;
3252
3253 ret = led_classdev_register(mmc_dev(mmc), &host->led);
3254 if (ret) {
3255 pr_err("%s: Failed to register LED device: %d\n",
3256 mmc_hostname(mmc), ret);
3257 goto reset;
3258 }
3259#endif
3260
3261 mmiowb();
3262
3263 mmc_add_host(mmc);
3264
3265 pr_info("%s: SDHCI controller on %s [%s] using %s\n",
3266 mmc_hostname(mmc), host->hw_name, dev_name(mmc_dev(mmc)),
3267 (host->flags & SDHCI_USE_ADMA) ? "ADMA" :
3268 (host->flags & SDHCI_USE_SDMA) ? "DMA" : "PIO");
3269
3270 sdhci_enable_card_detection(host);
3271
3272 return 0;
3273
3274#ifdef SDHCI_USE_LEDS_CLASS
3275reset:
3276 sdhci_reset(host, SDHCI_RESET_ALL);
3277 sdhci_mask_irqs(host, SDHCI_INT_ALL_MASK);
3278 free_irq(host->irq, host);
3279#endif
3280untasklet:
3281 tasklet_kill(&host->card_tasklet);
3282 tasklet_kill(&host->finish_tasklet);
3283
3284 return ret;
3285}
3286
3287EXPORT_SYMBOL_GPL(sdhci_add_host);
3288
3289void sdhci_remove_host(struct sdhci_host *host, int dead)
3290{
3291 unsigned long flags;
3292
3293 if (dead) {
3294 spin_lock_irqsave(&host->lock, flags);
3295
3296 host->flags |= SDHCI_DEVICE_DEAD;
3297
3298 if (host->mrq) {
3299 pr_err("%s: Controller removed during "
3300 " transfer!\n", mmc_hostname(host->mmc));
3301
3302 host->mrq->cmd->error = -ENOMEDIUM;
3303 tasklet_schedule(&host->finish_tasklet);
3304 }
3305
3306 spin_unlock_irqrestore(&host->lock, flags);
3307 }
3308
3309 sdhci_disable_card_detection(host);
3310
3311 mmc_remove_host(host->mmc);
3312
3313#ifdef SDHCI_USE_LEDS_CLASS
3314 led_classdev_unregister(&host->led);
3315#endif
3316
3317 if (!dead)
3318 sdhci_reset(host, SDHCI_RESET_ALL);
3319
3320 sdhci_mask_irqs(host, SDHCI_INT_ALL_MASK);
3321 free_irq(host->irq, host);
3322
3323 del_timer_sync(&host->timer);
3324
3325 tasklet_kill(&host->card_tasklet);
3326 tasklet_kill(&host->finish_tasklet);
3327
3328 if (host->vmmc) {
3329 regulator_disable(host->vmmc);
3330 regulator_put(host->vmmc);
3331 }
3332
3333 if (host->vqmmc) {
3334 regulator_disable(host->vqmmc);
3335 regulator_put(host->vqmmc);
3336 }
3337
3338 kfree(host->adma_desc);
3339 kfree(host->align_buffer);
3340
3341 host->adma_desc = NULL;
3342 host->align_buffer = NULL;
3343}
3344
3345EXPORT_SYMBOL_GPL(sdhci_remove_host);
3346
3347void sdhci_free_host(struct sdhci_host *host)
3348{
3349 mmc_free_host(host->mmc);
3350}
3351
3352EXPORT_SYMBOL_GPL(sdhci_free_host);
3353
3354/*****************************************************************************\
3355 * *
3356 * Driver init/exit *
3357 * *
3358\*****************************************************************************/
3359
3360static int __init sdhci_drv_init(void)
3361{
3362 pr_info(DRIVER_NAME
3363 ": Secure Digital Host Controller Interface driver\n");
3364 pr_info(DRIVER_NAME ": Copyright(c) Pierre Ossman\n");
3365
3366 return 0;
3367}
3368
3369static void __exit sdhci_drv_exit(void)
3370{
3371}
3372
3373module_init(sdhci_drv_init);
3374module_exit(sdhci_drv_exit);
3375
3376module_param(debug_quirks, uint, 0444);
3377module_param(debug_quirks2, uint, 0444);
3378
3379MODULE_AUTHOR("Pierre Ossman <pierre@ossman.eu>");
3380MODULE_DESCRIPTION("Secure Digital Host Controller Interface core driver");
3381MODULE_LICENSE("GPL");
3382
3383MODULE_PARM_DESC(debug_quirks, "Force certain quirks.");
3384MODULE_PARM_DESC(debug_quirks2, "Force certain other quirks.");
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * linux/drivers/mmc/host/sdhci.c - Secure Digital Host Controller Interface driver
4 *
5 * Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved.
6 *
7 * Thanks to the following companies for their support:
8 *
9 * - JMicron (hardware and technical support)
10 */
11
12#include <linux/delay.h>
13#include <linux/ktime.h>
14#include <linux/highmem.h>
15#include <linux/io.h>
16#include <linux/module.h>
17#include <linux/dma-mapping.h>
18#include <linux/slab.h>
19#include <linux/scatterlist.h>
20#include <linux/sizes.h>
21#include <linux/swiotlb.h>
22#include <linux/regulator/consumer.h>
23#include <linux/pm_runtime.h>
24#include <linux/of.h>
25
26#include <linux/leds.h>
27
28#include <linux/mmc/mmc.h>
29#include <linux/mmc/host.h>
30#include <linux/mmc/card.h>
31#include <linux/mmc/sdio.h>
32#include <linux/mmc/slot-gpio.h>
33
34#include "sdhci.h"
35
36#define DRIVER_NAME "sdhci"
37
38#define DBG(f, x...) \
39 pr_debug("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x)
40
41#define SDHCI_DUMP(f, x...) \
42 pr_err("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x)
43
44#define MAX_TUNING_LOOP 40
45
46static unsigned int debug_quirks = 0;
47static unsigned int debug_quirks2;
48
49static void sdhci_finish_data(struct sdhci_host *);
50
51static void sdhci_enable_preset_value(struct sdhci_host *host, bool enable);
52
53void sdhci_dumpregs(struct sdhci_host *host)
54{
55 SDHCI_DUMP("============ SDHCI REGISTER DUMP ===========\n");
56
57 SDHCI_DUMP("Sys addr: 0x%08x | Version: 0x%08x\n",
58 sdhci_readl(host, SDHCI_DMA_ADDRESS),
59 sdhci_readw(host, SDHCI_HOST_VERSION));
60 SDHCI_DUMP("Blk size: 0x%08x | Blk cnt: 0x%08x\n",
61 sdhci_readw(host, SDHCI_BLOCK_SIZE),
62 sdhci_readw(host, SDHCI_BLOCK_COUNT));
63 SDHCI_DUMP("Argument: 0x%08x | Trn mode: 0x%08x\n",
64 sdhci_readl(host, SDHCI_ARGUMENT),
65 sdhci_readw(host, SDHCI_TRANSFER_MODE));
66 SDHCI_DUMP("Present: 0x%08x | Host ctl: 0x%08x\n",
67 sdhci_readl(host, SDHCI_PRESENT_STATE),
68 sdhci_readb(host, SDHCI_HOST_CONTROL));
69 SDHCI_DUMP("Power: 0x%08x | Blk gap: 0x%08x\n",
70 sdhci_readb(host, SDHCI_POWER_CONTROL),
71 sdhci_readb(host, SDHCI_BLOCK_GAP_CONTROL));
72 SDHCI_DUMP("Wake-up: 0x%08x | Clock: 0x%08x\n",
73 sdhci_readb(host, SDHCI_WAKE_UP_CONTROL),
74 sdhci_readw(host, SDHCI_CLOCK_CONTROL));
75 SDHCI_DUMP("Timeout: 0x%08x | Int stat: 0x%08x\n",
76 sdhci_readb(host, SDHCI_TIMEOUT_CONTROL),
77 sdhci_readl(host, SDHCI_INT_STATUS));
78 SDHCI_DUMP("Int enab: 0x%08x | Sig enab: 0x%08x\n",
79 sdhci_readl(host, SDHCI_INT_ENABLE),
80 sdhci_readl(host, SDHCI_SIGNAL_ENABLE));
81 SDHCI_DUMP("ACmd stat: 0x%08x | Slot int: 0x%08x\n",
82 sdhci_readw(host, SDHCI_AUTO_CMD_STATUS),
83 sdhci_readw(host, SDHCI_SLOT_INT_STATUS));
84 SDHCI_DUMP("Caps: 0x%08x | Caps_1: 0x%08x\n",
85 sdhci_readl(host, SDHCI_CAPABILITIES),
86 sdhci_readl(host, SDHCI_CAPABILITIES_1));
87 SDHCI_DUMP("Cmd: 0x%08x | Max curr: 0x%08x\n",
88 sdhci_readw(host, SDHCI_COMMAND),
89 sdhci_readl(host, SDHCI_MAX_CURRENT));
90 SDHCI_DUMP("Resp[0]: 0x%08x | Resp[1]: 0x%08x\n",
91 sdhci_readl(host, SDHCI_RESPONSE),
92 sdhci_readl(host, SDHCI_RESPONSE + 4));
93 SDHCI_DUMP("Resp[2]: 0x%08x | Resp[3]: 0x%08x\n",
94 sdhci_readl(host, SDHCI_RESPONSE + 8),
95 sdhci_readl(host, SDHCI_RESPONSE + 12));
96 SDHCI_DUMP("Host ctl2: 0x%08x\n",
97 sdhci_readw(host, SDHCI_HOST_CONTROL2));
98
99 if (host->flags & SDHCI_USE_ADMA) {
100 if (host->flags & SDHCI_USE_64_BIT_DMA) {
101 SDHCI_DUMP("ADMA Err: 0x%08x | ADMA Ptr: 0x%08x%08x\n",
102 sdhci_readl(host, SDHCI_ADMA_ERROR),
103 sdhci_readl(host, SDHCI_ADMA_ADDRESS_HI),
104 sdhci_readl(host, SDHCI_ADMA_ADDRESS));
105 } else {
106 SDHCI_DUMP("ADMA Err: 0x%08x | ADMA Ptr: 0x%08x\n",
107 sdhci_readl(host, SDHCI_ADMA_ERROR),
108 sdhci_readl(host, SDHCI_ADMA_ADDRESS));
109 }
110 }
111
112 SDHCI_DUMP("============================================\n");
113}
114EXPORT_SYMBOL_GPL(sdhci_dumpregs);
115
116/*****************************************************************************\
117 * *
118 * Low level functions *
119 * *
120\*****************************************************************************/
121
122static void sdhci_do_enable_v4_mode(struct sdhci_host *host)
123{
124 u16 ctrl2;
125
126 ctrl2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
127 if (ctrl2 & SDHCI_CTRL_V4_MODE)
128 return;
129
130 ctrl2 |= SDHCI_CTRL_V4_MODE;
131 sdhci_writew(host, ctrl2, SDHCI_HOST_CONTROL2);
132}
133
134/*
135 * This can be called before sdhci_add_host() by Vendor's host controller
136 * driver to enable v4 mode if supported.
137 */
138void sdhci_enable_v4_mode(struct sdhci_host *host)
139{
140 host->v4_mode = true;
141 sdhci_do_enable_v4_mode(host);
142}
143EXPORT_SYMBOL_GPL(sdhci_enable_v4_mode);
144
145static inline bool sdhci_data_line_cmd(struct mmc_command *cmd)
146{
147 return cmd->data || cmd->flags & MMC_RSP_BUSY;
148}
149
150static void sdhci_set_card_detection(struct sdhci_host *host, bool enable)
151{
152 u32 present;
153
154 if ((host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) ||
155 !mmc_card_is_removable(host->mmc))
156 return;
157
158 if (enable) {
159 present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
160 SDHCI_CARD_PRESENT;
161
162 host->ier |= present ? SDHCI_INT_CARD_REMOVE :
163 SDHCI_INT_CARD_INSERT;
164 } else {
165 host->ier &= ~(SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT);
166 }
167
168 sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
169 sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
170}
171
172static void sdhci_enable_card_detection(struct sdhci_host *host)
173{
174 sdhci_set_card_detection(host, true);
175}
176
177static void sdhci_disable_card_detection(struct sdhci_host *host)
178{
179 sdhci_set_card_detection(host, false);
180}
181
182static void sdhci_runtime_pm_bus_on(struct sdhci_host *host)
183{
184 if (host->bus_on)
185 return;
186 host->bus_on = true;
187 pm_runtime_get_noresume(host->mmc->parent);
188}
189
190static void sdhci_runtime_pm_bus_off(struct sdhci_host *host)
191{
192 if (!host->bus_on)
193 return;
194 host->bus_on = false;
195 pm_runtime_put_noidle(host->mmc->parent);
196}
197
198void sdhci_reset(struct sdhci_host *host, u8 mask)
199{
200 ktime_t timeout;
201
202 sdhci_writeb(host, mask, SDHCI_SOFTWARE_RESET);
203
204 if (mask & SDHCI_RESET_ALL) {
205 host->clock = 0;
206 /* Reset-all turns off SD Bus Power */
207 if (host->quirks2 & SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON)
208 sdhci_runtime_pm_bus_off(host);
209 }
210
211 /* Wait max 100 ms */
212 timeout = ktime_add_ms(ktime_get(), 100);
213
214 /* hw clears the bit when it's done */
215 while (1) {
216 bool timedout = ktime_after(ktime_get(), timeout);
217
218 if (!(sdhci_readb(host, SDHCI_SOFTWARE_RESET) & mask))
219 break;
220 if (timedout) {
221 pr_err("%s: Reset 0x%x never completed.\n",
222 mmc_hostname(host->mmc), (int)mask);
223 sdhci_dumpregs(host);
224 return;
225 }
226 udelay(10);
227 }
228}
229EXPORT_SYMBOL_GPL(sdhci_reset);
230
231static void sdhci_do_reset(struct sdhci_host *host, u8 mask)
232{
233 if (host->quirks & SDHCI_QUIRK_NO_CARD_NO_RESET) {
234 struct mmc_host *mmc = host->mmc;
235
236 if (!mmc->ops->get_cd(mmc))
237 return;
238 }
239
240 host->ops->reset(host, mask);
241
242 if (mask & SDHCI_RESET_ALL) {
243 if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
244 if (host->ops->enable_dma)
245 host->ops->enable_dma(host);
246 }
247
248 /* Resetting the controller clears many */
249 host->preset_enabled = false;
250 }
251}
252
253static void sdhci_set_default_irqs(struct sdhci_host *host)
254{
255 host->ier = SDHCI_INT_BUS_POWER | SDHCI_INT_DATA_END_BIT |
256 SDHCI_INT_DATA_CRC | SDHCI_INT_DATA_TIMEOUT |
257 SDHCI_INT_INDEX | SDHCI_INT_END_BIT | SDHCI_INT_CRC |
258 SDHCI_INT_TIMEOUT | SDHCI_INT_DATA_END |
259 SDHCI_INT_RESPONSE;
260
261 if (host->tuning_mode == SDHCI_TUNING_MODE_2 ||
262 host->tuning_mode == SDHCI_TUNING_MODE_3)
263 host->ier |= SDHCI_INT_RETUNE;
264
265 sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
266 sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
267}
268
269static void sdhci_config_dma(struct sdhci_host *host)
270{
271 u8 ctrl;
272 u16 ctrl2;
273
274 if (host->version < SDHCI_SPEC_200)
275 return;
276
277 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
278
279 /*
280 * Always adjust the DMA selection as some controllers
281 * (e.g. JMicron) can't do PIO properly when the selection
282 * is ADMA.
283 */
284 ctrl &= ~SDHCI_CTRL_DMA_MASK;
285 if (!(host->flags & SDHCI_REQ_USE_DMA))
286 goto out;
287
288 /* Note if DMA Select is zero then SDMA is selected */
289 if (host->flags & SDHCI_USE_ADMA)
290 ctrl |= SDHCI_CTRL_ADMA32;
291
292 if (host->flags & SDHCI_USE_64_BIT_DMA) {
293 /*
294 * If v4 mode, all supported DMA can be 64-bit addressing if
295 * controller supports 64-bit system address, otherwise only
296 * ADMA can support 64-bit addressing.
297 */
298 if (host->v4_mode) {
299 ctrl2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
300 ctrl2 |= SDHCI_CTRL_64BIT_ADDR;
301 sdhci_writew(host, ctrl2, SDHCI_HOST_CONTROL2);
302 } else if (host->flags & SDHCI_USE_ADMA) {
303 /*
304 * Don't need to undo SDHCI_CTRL_ADMA32 in order to
305 * set SDHCI_CTRL_ADMA64.
306 */
307 ctrl |= SDHCI_CTRL_ADMA64;
308 }
309 }
310
311out:
312 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
313}
314
315static void sdhci_init(struct sdhci_host *host, int soft)
316{
317 struct mmc_host *mmc = host->mmc;
318
319 if (soft)
320 sdhci_do_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA);
321 else
322 sdhci_do_reset(host, SDHCI_RESET_ALL);
323
324 if (host->v4_mode)
325 sdhci_do_enable_v4_mode(host);
326
327 sdhci_set_default_irqs(host);
328
329 host->cqe_on = false;
330
331 if (soft) {
332 /* force clock reconfiguration */
333 host->clock = 0;
334 mmc->ops->set_ios(mmc, &mmc->ios);
335 }
336}
337
338static void sdhci_reinit(struct sdhci_host *host)
339{
340 sdhci_init(host, 0);
341 sdhci_enable_card_detection(host);
342}
343
344static void __sdhci_led_activate(struct sdhci_host *host)
345{
346 u8 ctrl;
347
348 if (host->quirks & SDHCI_QUIRK_NO_LED)
349 return;
350
351 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
352 ctrl |= SDHCI_CTRL_LED;
353 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
354}
355
356static void __sdhci_led_deactivate(struct sdhci_host *host)
357{
358 u8 ctrl;
359
360 if (host->quirks & SDHCI_QUIRK_NO_LED)
361 return;
362
363 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
364 ctrl &= ~SDHCI_CTRL_LED;
365 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
366}
367
368#if IS_REACHABLE(CONFIG_LEDS_CLASS)
369static void sdhci_led_control(struct led_classdev *led,
370 enum led_brightness brightness)
371{
372 struct sdhci_host *host = container_of(led, struct sdhci_host, led);
373 unsigned long flags;
374
375 spin_lock_irqsave(&host->lock, flags);
376
377 if (host->runtime_suspended)
378 goto out;
379
380 if (brightness == LED_OFF)
381 __sdhci_led_deactivate(host);
382 else
383 __sdhci_led_activate(host);
384out:
385 spin_unlock_irqrestore(&host->lock, flags);
386}
387
388static int sdhci_led_register(struct sdhci_host *host)
389{
390 struct mmc_host *mmc = host->mmc;
391
392 if (host->quirks & SDHCI_QUIRK_NO_LED)
393 return 0;
394
395 snprintf(host->led_name, sizeof(host->led_name),
396 "%s::", mmc_hostname(mmc));
397
398 host->led.name = host->led_name;
399 host->led.brightness = LED_OFF;
400 host->led.default_trigger = mmc_hostname(mmc);
401 host->led.brightness_set = sdhci_led_control;
402
403 return led_classdev_register(mmc_dev(mmc), &host->led);
404}
405
406static void sdhci_led_unregister(struct sdhci_host *host)
407{
408 if (host->quirks & SDHCI_QUIRK_NO_LED)
409 return;
410
411 led_classdev_unregister(&host->led);
412}
413
414static inline void sdhci_led_activate(struct sdhci_host *host)
415{
416}
417
418static inline void sdhci_led_deactivate(struct sdhci_host *host)
419{
420}
421
422#else
423
424static inline int sdhci_led_register(struct sdhci_host *host)
425{
426 return 0;
427}
428
429static inline void sdhci_led_unregister(struct sdhci_host *host)
430{
431}
432
433static inline void sdhci_led_activate(struct sdhci_host *host)
434{
435 __sdhci_led_activate(host);
436}
437
438static inline void sdhci_led_deactivate(struct sdhci_host *host)
439{
440 __sdhci_led_deactivate(host);
441}
442
443#endif
444
445static void sdhci_mod_timer(struct sdhci_host *host, struct mmc_request *mrq,
446 unsigned long timeout)
447{
448 if (sdhci_data_line_cmd(mrq->cmd))
449 mod_timer(&host->data_timer, timeout);
450 else
451 mod_timer(&host->timer, timeout);
452}
453
454static void sdhci_del_timer(struct sdhci_host *host, struct mmc_request *mrq)
455{
456 if (sdhci_data_line_cmd(mrq->cmd))
457 del_timer(&host->data_timer);
458 else
459 del_timer(&host->timer);
460}
461
462static inline bool sdhci_has_requests(struct sdhci_host *host)
463{
464 return host->cmd || host->data_cmd;
465}
466
467/*****************************************************************************\
468 * *
469 * Core functions *
470 * *
471\*****************************************************************************/
472
473static void sdhci_read_block_pio(struct sdhci_host *host)
474{
475 unsigned long flags;
476 size_t blksize, len, chunk;
477 u32 uninitialized_var(scratch);
478 u8 *buf;
479
480 DBG("PIO reading\n");
481
482 blksize = host->data->blksz;
483 chunk = 0;
484
485 local_irq_save(flags);
486
487 while (blksize) {
488 BUG_ON(!sg_miter_next(&host->sg_miter));
489
490 len = min(host->sg_miter.length, blksize);
491
492 blksize -= len;
493 host->sg_miter.consumed = len;
494
495 buf = host->sg_miter.addr;
496
497 while (len) {
498 if (chunk == 0) {
499 scratch = sdhci_readl(host, SDHCI_BUFFER);
500 chunk = 4;
501 }
502
503 *buf = scratch & 0xFF;
504
505 buf++;
506 scratch >>= 8;
507 chunk--;
508 len--;
509 }
510 }
511
512 sg_miter_stop(&host->sg_miter);
513
514 local_irq_restore(flags);
515}
516
517static void sdhci_write_block_pio(struct sdhci_host *host)
518{
519 unsigned long flags;
520 size_t blksize, len, chunk;
521 u32 scratch;
522 u8 *buf;
523
524 DBG("PIO writing\n");
525
526 blksize = host->data->blksz;
527 chunk = 0;
528 scratch = 0;
529
530 local_irq_save(flags);
531
532 while (blksize) {
533 BUG_ON(!sg_miter_next(&host->sg_miter));
534
535 len = min(host->sg_miter.length, blksize);
536
537 blksize -= len;
538 host->sg_miter.consumed = len;
539
540 buf = host->sg_miter.addr;
541
542 while (len) {
543 scratch |= (u32)*buf << (chunk * 8);
544
545 buf++;
546 chunk++;
547 len--;
548
549 if ((chunk == 4) || ((len == 0) && (blksize == 0))) {
550 sdhci_writel(host, scratch, SDHCI_BUFFER);
551 chunk = 0;
552 scratch = 0;
553 }
554 }
555 }
556
557 sg_miter_stop(&host->sg_miter);
558
559 local_irq_restore(flags);
560}
561
562static void sdhci_transfer_pio(struct sdhci_host *host)
563{
564 u32 mask;
565
566 if (host->blocks == 0)
567 return;
568
569 if (host->data->flags & MMC_DATA_READ)
570 mask = SDHCI_DATA_AVAILABLE;
571 else
572 mask = SDHCI_SPACE_AVAILABLE;
573
574 /*
575 * Some controllers (JMicron JMB38x) mess up the buffer bits
576 * for transfers < 4 bytes. As long as it is just one block,
577 * we can ignore the bits.
578 */
579 if ((host->quirks & SDHCI_QUIRK_BROKEN_SMALL_PIO) &&
580 (host->data->blocks == 1))
581 mask = ~0;
582
583 while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {
584 if (host->quirks & SDHCI_QUIRK_PIO_NEEDS_DELAY)
585 udelay(100);
586
587 if (host->data->flags & MMC_DATA_READ)
588 sdhci_read_block_pio(host);
589 else
590 sdhci_write_block_pio(host);
591
592 host->blocks--;
593 if (host->blocks == 0)
594 break;
595 }
596
597 DBG("PIO transfer complete.\n");
598}
599
600static int sdhci_pre_dma_transfer(struct sdhci_host *host,
601 struct mmc_data *data, int cookie)
602{
603 int sg_count;
604
605 /*
606 * If the data buffers are already mapped, return the previous
607 * dma_map_sg() result.
608 */
609 if (data->host_cookie == COOKIE_PRE_MAPPED)
610 return data->sg_count;
611
612 /* Bounce write requests to the bounce buffer */
613 if (host->bounce_buffer) {
614 unsigned int length = data->blksz * data->blocks;
615
616 if (length > host->bounce_buffer_size) {
617 pr_err("%s: asked for transfer of %u bytes exceeds bounce buffer %u bytes\n",
618 mmc_hostname(host->mmc), length,
619 host->bounce_buffer_size);
620 return -EIO;
621 }
622 if (mmc_get_dma_dir(data) == DMA_TO_DEVICE) {
623 /* Copy the data to the bounce buffer */
624 sg_copy_to_buffer(data->sg, data->sg_len,
625 host->bounce_buffer,
626 length);
627 }
628 /* Switch ownership to the DMA */
629 dma_sync_single_for_device(host->mmc->parent,
630 host->bounce_addr,
631 host->bounce_buffer_size,
632 mmc_get_dma_dir(data));
633 /* Just a dummy value */
634 sg_count = 1;
635 } else {
636 /* Just access the data directly from memory */
637 sg_count = dma_map_sg(mmc_dev(host->mmc),
638 data->sg, data->sg_len,
639 mmc_get_dma_dir(data));
640 }
641
642 if (sg_count == 0)
643 return -ENOSPC;
644
645 data->sg_count = sg_count;
646 data->host_cookie = cookie;
647
648 return sg_count;
649}
650
651static char *sdhci_kmap_atomic(struct scatterlist *sg, unsigned long *flags)
652{
653 local_irq_save(*flags);
654 return kmap_atomic(sg_page(sg)) + sg->offset;
655}
656
657static void sdhci_kunmap_atomic(void *buffer, unsigned long *flags)
658{
659 kunmap_atomic(buffer);
660 local_irq_restore(*flags);
661}
662
663void sdhci_adma_write_desc(struct sdhci_host *host, void **desc,
664 dma_addr_t addr, int len, unsigned int cmd)
665{
666 struct sdhci_adma2_64_desc *dma_desc = *desc;
667
668 /* 32-bit and 64-bit descriptors have these members in same position */
669 dma_desc->cmd = cpu_to_le16(cmd);
670 dma_desc->len = cpu_to_le16(len);
671 dma_desc->addr_lo = cpu_to_le32(lower_32_bits(addr));
672
673 if (host->flags & SDHCI_USE_64_BIT_DMA)
674 dma_desc->addr_hi = cpu_to_le32(upper_32_bits(addr));
675
676 *desc += host->desc_sz;
677}
678EXPORT_SYMBOL_GPL(sdhci_adma_write_desc);
679
680static inline void __sdhci_adma_write_desc(struct sdhci_host *host,
681 void **desc, dma_addr_t addr,
682 int len, unsigned int cmd)
683{
684 if (host->ops->adma_write_desc)
685 host->ops->adma_write_desc(host, desc, addr, len, cmd);
686 else
687 sdhci_adma_write_desc(host, desc, addr, len, cmd);
688}
689
690static void sdhci_adma_mark_end(void *desc)
691{
692 struct sdhci_adma2_64_desc *dma_desc = desc;
693
694 /* 32-bit and 64-bit descriptors have 'cmd' in same position */
695 dma_desc->cmd |= cpu_to_le16(ADMA2_END);
696}
697
698static void sdhci_adma_table_pre(struct sdhci_host *host,
699 struct mmc_data *data, int sg_count)
700{
701 struct scatterlist *sg;
702 unsigned long flags;
703 dma_addr_t addr, align_addr;
704 void *desc, *align;
705 char *buffer;
706 int len, offset, i;
707
708 /*
709 * The spec does not specify endianness of descriptor table.
710 * We currently guess that it is LE.
711 */
712
713 host->sg_count = sg_count;
714
715 desc = host->adma_table;
716 align = host->align_buffer;
717
718 align_addr = host->align_addr;
719
720 for_each_sg(data->sg, sg, host->sg_count, i) {
721 addr = sg_dma_address(sg);
722 len = sg_dma_len(sg);
723
724 /*
725 * The SDHCI specification states that ADMA addresses must
726 * be 32-bit aligned. If they aren't, then we use a bounce
727 * buffer for the (up to three) bytes that screw up the
728 * alignment.
729 */
730 offset = (SDHCI_ADMA2_ALIGN - (addr & SDHCI_ADMA2_MASK)) &
731 SDHCI_ADMA2_MASK;
732 if (offset) {
733 if (data->flags & MMC_DATA_WRITE) {
734 buffer = sdhci_kmap_atomic(sg, &flags);
735 memcpy(align, buffer, offset);
736 sdhci_kunmap_atomic(buffer, &flags);
737 }
738
739 /* tran, valid */
740 __sdhci_adma_write_desc(host, &desc, align_addr,
741 offset, ADMA2_TRAN_VALID);
742
743 BUG_ON(offset > 65536);
744
745 align += SDHCI_ADMA2_ALIGN;
746 align_addr += SDHCI_ADMA2_ALIGN;
747
748 addr += offset;
749 len -= offset;
750 }
751
752 BUG_ON(len > 65536);
753
754 /* tran, valid */
755 if (len)
756 __sdhci_adma_write_desc(host, &desc, addr, len,
757 ADMA2_TRAN_VALID);
758
759 /*
760 * If this triggers then we have a calculation bug
761 * somewhere. :/
762 */
763 WARN_ON((desc - host->adma_table) >= host->adma_table_sz);
764 }
765
766 if (host->quirks & SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC) {
767 /* Mark the last descriptor as the terminating descriptor */
768 if (desc != host->adma_table) {
769 desc -= host->desc_sz;
770 sdhci_adma_mark_end(desc);
771 }
772 } else {
773 /* Add a terminating entry - nop, end, valid */
774 __sdhci_adma_write_desc(host, &desc, 0, 0, ADMA2_NOP_END_VALID);
775 }
776}
777
778static void sdhci_adma_table_post(struct sdhci_host *host,
779 struct mmc_data *data)
780{
781 struct scatterlist *sg;
782 int i, size;
783 void *align;
784 char *buffer;
785 unsigned long flags;
786
787 if (data->flags & MMC_DATA_READ) {
788 bool has_unaligned = false;
789
790 /* Do a quick scan of the SG list for any unaligned mappings */
791 for_each_sg(data->sg, sg, host->sg_count, i)
792 if (sg_dma_address(sg) & SDHCI_ADMA2_MASK) {
793 has_unaligned = true;
794 break;
795 }
796
797 if (has_unaligned) {
798 dma_sync_sg_for_cpu(mmc_dev(host->mmc), data->sg,
799 data->sg_len, DMA_FROM_DEVICE);
800
801 align = host->align_buffer;
802
803 for_each_sg(data->sg, sg, host->sg_count, i) {
804 if (sg_dma_address(sg) & SDHCI_ADMA2_MASK) {
805 size = SDHCI_ADMA2_ALIGN -
806 (sg_dma_address(sg) & SDHCI_ADMA2_MASK);
807
808 buffer = sdhci_kmap_atomic(sg, &flags);
809 memcpy(buffer, align, size);
810 sdhci_kunmap_atomic(buffer, &flags);
811
812 align += SDHCI_ADMA2_ALIGN;
813 }
814 }
815 }
816 }
817}
818
819static void sdhci_set_adma_addr(struct sdhci_host *host, dma_addr_t addr)
820{
821 sdhci_writel(host, lower_32_bits(addr), SDHCI_ADMA_ADDRESS);
822 if (host->flags & SDHCI_USE_64_BIT_DMA)
823 sdhci_writel(host, upper_32_bits(addr), SDHCI_ADMA_ADDRESS_HI);
824}
825
826static dma_addr_t sdhci_sdma_address(struct sdhci_host *host)
827{
828 if (host->bounce_buffer)
829 return host->bounce_addr;
830 else
831 return sg_dma_address(host->data->sg);
832}
833
834static void sdhci_set_sdma_addr(struct sdhci_host *host, dma_addr_t addr)
835{
836 if (host->v4_mode)
837 sdhci_set_adma_addr(host, addr);
838 else
839 sdhci_writel(host, addr, SDHCI_DMA_ADDRESS);
840}
841
842static unsigned int sdhci_target_timeout(struct sdhci_host *host,
843 struct mmc_command *cmd,
844 struct mmc_data *data)
845{
846 unsigned int target_timeout;
847
848 /* timeout in us */
849 if (!data) {
850 target_timeout = cmd->busy_timeout * 1000;
851 } else {
852 target_timeout = DIV_ROUND_UP(data->timeout_ns, 1000);
853 if (host->clock && data->timeout_clks) {
854 unsigned long long val;
855
856 /*
857 * data->timeout_clks is in units of clock cycles.
858 * host->clock is in Hz. target_timeout is in us.
859 * Hence, us = 1000000 * cycles / Hz. Round up.
860 */
861 val = 1000000ULL * data->timeout_clks;
862 if (do_div(val, host->clock))
863 target_timeout++;
864 target_timeout += val;
865 }
866 }
867
868 return target_timeout;
869}
870
871static void sdhci_calc_sw_timeout(struct sdhci_host *host,
872 struct mmc_command *cmd)
873{
874 struct mmc_data *data = cmd->data;
875 struct mmc_host *mmc = host->mmc;
876 struct mmc_ios *ios = &mmc->ios;
877 unsigned char bus_width = 1 << ios->bus_width;
878 unsigned int blksz;
879 unsigned int freq;
880 u64 target_timeout;
881 u64 transfer_time;
882
883 target_timeout = sdhci_target_timeout(host, cmd, data);
884 target_timeout *= NSEC_PER_USEC;
885
886 if (data) {
887 blksz = data->blksz;
888 freq = host->mmc->actual_clock ? : host->clock;
889 transfer_time = (u64)blksz * NSEC_PER_SEC * (8 / bus_width);
890 do_div(transfer_time, freq);
891 /* multiply by '2' to account for any unknowns */
892 transfer_time = transfer_time * 2;
893 /* calculate timeout for the entire data */
894 host->data_timeout = data->blocks * target_timeout +
895 transfer_time;
896 } else {
897 host->data_timeout = target_timeout;
898 }
899
900 if (host->data_timeout)
901 host->data_timeout += MMC_CMD_TRANSFER_TIME;
902}
903
904static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd,
905 bool *too_big)
906{
907 u8 count;
908 struct mmc_data *data;
909 unsigned target_timeout, current_timeout;
910
911 *too_big = true;
912
913 /*
914 * If the host controller provides us with an incorrect timeout
915 * value, just skip the check and use 0xE. The hardware may take
916 * longer to time out, but that's much better than having a too-short
917 * timeout value.
918 */
919 if (host->quirks & SDHCI_QUIRK_BROKEN_TIMEOUT_VAL)
920 return 0xE;
921
922 /* Unspecified command, asume max */
923 if (cmd == NULL)
924 return 0xE;
925
926 data = cmd->data;
927 /* Unspecified timeout, assume max */
928 if (!data && !cmd->busy_timeout)
929 return 0xE;
930
931 /* timeout in us */
932 target_timeout = sdhci_target_timeout(host, cmd, data);
933
934 /*
935 * Figure out needed cycles.
936 * We do this in steps in order to fit inside a 32 bit int.
937 * The first step is the minimum timeout, which will have a
938 * minimum resolution of 6 bits:
939 * (1) 2^13*1000 > 2^22,
940 * (2) host->timeout_clk < 2^16
941 * =>
942 * (1) / (2) > 2^6
943 */
944 count = 0;
945 current_timeout = (1 << 13) * 1000 / host->timeout_clk;
946 while (current_timeout < target_timeout) {
947 count++;
948 current_timeout <<= 1;
949 if (count >= 0xF)
950 break;
951 }
952
953 if (count >= 0xF) {
954 if (!(host->quirks2 & SDHCI_QUIRK2_DISABLE_HW_TIMEOUT))
955 DBG("Too large timeout 0x%x requested for CMD%d!\n",
956 count, cmd->opcode);
957 count = 0xE;
958 } else {
959 *too_big = false;
960 }
961
962 return count;
963}
964
965static void sdhci_set_transfer_irqs(struct sdhci_host *host)
966{
967 u32 pio_irqs = SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL;
968 u32 dma_irqs = SDHCI_INT_DMA_END | SDHCI_INT_ADMA_ERROR;
969
970 if (host->flags & SDHCI_REQ_USE_DMA)
971 host->ier = (host->ier & ~pio_irqs) | dma_irqs;
972 else
973 host->ier = (host->ier & ~dma_irqs) | pio_irqs;
974
975 if (host->flags & (SDHCI_AUTO_CMD23 | SDHCI_AUTO_CMD12))
976 host->ier |= SDHCI_INT_AUTO_CMD_ERR;
977 else
978 host->ier &= ~SDHCI_INT_AUTO_CMD_ERR;
979
980 sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
981 sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
982}
983
984static void sdhci_set_data_timeout_irq(struct sdhci_host *host, bool enable)
985{
986 if (enable)
987 host->ier |= SDHCI_INT_DATA_TIMEOUT;
988 else
989 host->ier &= ~SDHCI_INT_DATA_TIMEOUT;
990 sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
991 sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
992}
993
994static void sdhci_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
995{
996 u8 count;
997
998 if (host->ops->set_timeout) {
999 host->ops->set_timeout(host, cmd);
1000 } else {
1001 bool too_big = false;
1002
1003 count = sdhci_calc_timeout(host, cmd, &too_big);
1004
1005 if (too_big &&
1006 host->quirks2 & SDHCI_QUIRK2_DISABLE_HW_TIMEOUT) {
1007 sdhci_calc_sw_timeout(host, cmd);
1008 sdhci_set_data_timeout_irq(host, false);
1009 } else if (!(host->ier & SDHCI_INT_DATA_TIMEOUT)) {
1010 sdhci_set_data_timeout_irq(host, true);
1011 }
1012
1013 sdhci_writeb(host, count, SDHCI_TIMEOUT_CONTROL);
1014 }
1015}
1016
1017static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_command *cmd)
1018{
1019 struct mmc_data *data = cmd->data;
1020
1021 host->data_timeout = 0;
1022
1023 if (sdhci_data_line_cmd(cmd))
1024 sdhci_set_timeout(host, cmd);
1025
1026 if (!data)
1027 return;
1028
1029 WARN_ON(host->data);
1030
1031 /* Sanity checks */
1032 BUG_ON(data->blksz * data->blocks > 524288);
1033 BUG_ON(data->blksz > host->mmc->max_blk_size);
1034 BUG_ON(data->blocks > 65535);
1035
1036 host->data = data;
1037 host->data_early = 0;
1038 host->data->bytes_xfered = 0;
1039
1040 if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
1041 struct scatterlist *sg;
1042 unsigned int length_mask, offset_mask;
1043 int i;
1044
1045 host->flags |= SDHCI_REQ_USE_DMA;
1046
1047 /*
1048 * FIXME: This doesn't account for merging when mapping the
1049 * scatterlist.
1050 *
1051 * The assumption here being that alignment and lengths are
1052 * the same after DMA mapping to device address space.
1053 */
1054 length_mask = 0;
1055 offset_mask = 0;
1056 if (host->flags & SDHCI_USE_ADMA) {
1057 if (host->quirks & SDHCI_QUIRK_32BIT_ADMA_SIZE) {
1058 length_mask = 3;
1059 /*
1060 * As we use up to 3 byte chunks to work
1061 * around alignment problems, we need to
1062 * check the offset as well.
1063 */
1064 offset_mask = 3;
1065 }
1066 } else {
1067 if (host->quirks & SDHCI_QUIRK_32BIT_DMA_SIZE)
1068 length_mask = 3;
1069 if (host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR)
1070 offset_mask = 3;
1071 }
1072
1073 if (unlikely(length_mask | offset_mask)) {
1074 for_each_sg(data->sg, sg, data->sg_len, i) {
1075 if (sg->length & length_mask) {
1076 DBG("Reverting to PIO because of transfer size (%d)\n",
1077 sg->length);
1078 host->flags &= ~SDHCI_REQ_USE_DMA;
1079 break;
1080 }
1081 if (sg->offset & offset_mask) {
1082 DBG("Reverting to PIO because of bad alignment\n");
1083 host->flags &= ~SDHCI_REQ_USE_DMA;
1084 break;
1085 }
1086 }
1087 }
1088 }
1089
1090 if (host->flags & SDHCI_REQ_USE_DMA) {
1091 int sg_cnt = sdhci_pre_dma_transfer(host, data, COOKIE_MAPPED);
1092
1093 if (sg_cnt <= 0) {
1094 /*
1095 * This only happens when someone fed
1096 * us an invalid request.
1097 */
1098 WARN_ON(1);
1099 host->flags &= ~SDHCI_REQ_USE_DMA;
1100 } else if (host->flags & SDHCI_USE_ADMA) {
1101 sdhci_adma_table_pre(host, data, sg_cnt);
1102 sdhci_set_adma_addr(host, host->adma_addr);
1103 } else {
1104 WARN_ON(sg_cnt != 1);
1105 sdhci_set_sdma_addr(host, sdhci_sdma_address(host));
1106 }
1107 }
1108
1109 sdhci_config_dma(host);
1110
1111 if (!(host->flags & SDHCI_REQ_USE_DMA)) {
1112 int flags;
1113
1114 flags = SG_MITER_ATOMIC;
1115 if (host->data->flags & MMC_DATA_READ)
1116 flags |= SG_MITER_TO_SG;
1117 else
1118 flags |= SG_MITER_FROM_SG;
1119 sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
1120 host->blocks = data->blocks;
1121 }
1122
1123 sdhci_set_transfer_irqs(host);
1124
1125 /* Set the DMA boundary value and block size */
1126 sdhci_writew(host, SDHCI_MAKE_BLKSZ(host->sdma_boundary, data->blksz),
1127 SDHCI_BLOCK_SIZE);
1128
1129 /*
1130 * For Version 4.10 onwards, if v4 mode is enabled, 32-bit Block Count
1131 * can be supported, in that case 16-bit block count register must be 0.
1132 */
1133 if (host->version >= SDHCI_SPEC_410 && host->v4_mode &&
1134 (host->quirks2 & SDHCI_QUIRK2_USE_32BIT_BLK_CNT)) {
1135 if (sdhci_readw(host, SDHCI_BLOCK_COUNT))
1136 sdhci_writew(host, 0, SDHCI_BLOCK_COUNT);
1137 sdhci_writew(host, data->blocks, SDHCI_32BIT_BLK_CNT);
1138 } else {
1139 sdhci_writew(host, data->blocks, SDHCI_BLOCK_COUNT);
1140 }
1141}
1142
1143static inline bool sdhci_auto_cmd12(struct sdhci_host *host,
1144 struct mmc_request *mrq)
1145{
1146 return !mrq->sbc && (host->flags & SDHCI_AUTO_CMD12) &&
1147 !mrq->cap_cmd_during_tfr;
1148}
1149
1150static inline void sdhci_auto_cmd_select(struct sdhci_host *host,
1151 struct mmc_command *cmd,
1152 u16 *mode)
1153{
1154 bool use_cmd12 = sdhci_auto_cmd12(host, cmd->mrq) &&
1155 (cmd->opcode != SD_IO_RW_EXTENDED);
1156 bool use_cmd23 = cmd->mrq->sbc && (host->flags & SDHCI_AUTO_CMD23);
1157 u16 ctrl2;
1158
1159 /*
1160 * In case of Version 4.10 or later, use of 'Auto CMD Auto
1161 * Select' is recommended rather than use of 'Auto CMD12
1162 * Enable' or 'Auto CMD23 Enable'.
1163 */
1164 if (host->version >= SDHCI_SPEC_410 && (use_cmd12 || use_cmd23)) {
1165 *mode |= SDHCI_TRNS_AUTO_SEL;
1166
1167 ctrl2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1168 if (use_cmd23)
1169 ctrl2 |= SDHCI_CMD23_ENABLE;
1170 else
1171 ctrl2 &= ~SDHCI_CMD23_ENABLE;
1172 sdhci_writew(host, ctrl2, SDHCI_HOST_CONTROL2);
1173
1174 return;
1175 }
1176
1177 /*
1178 * If we are sending CMD23, CMD12 never gets sent
1179 * on successful completion (so no Auto-CMD12).
1180 */
1181 if (use_cmd12)
1182 *mode |= SDHCI_TRNS_AUTO_CMD12;
1183 else if (use_cmd23)
1184 *mode |= SDHCI_TRNS_AUTO_CMD23;
1185}
1186
1187static void sdhci_set_transfer_mode(struct sdhci_host *host,
1188 struct mmc_command *cmd)
1189{
1190 u16 mode = 0;
1191 struct mmc_data *data = cmd->data;
1192
1193 if (data == NULL) {
1194 if (host->quirks2 &
1195 SDHCI_QUIRK2_CLEAR_TRANSFERMODE_REG_BEFORE_CMD) {
1196 /* must not clear SDHCI_TRANSFER_MODE when tuning */
1197 if (cmd->opcode != MMC_SEND_TUNING_BLOCK_HS200)
1198 sdhci_writew(host, 0x0, SDHCI_TRANSFER_MODE);
1199 } else {
1200 /* clear Auto CMD settings for no data CMDs */
1201 mode = sdhci_readw(host, SDHCI_TRANSFER_MODE);
1202 sdhci_writew(host, mode & ~(SDHCI_TRNS_AUTO_CMD12 |
1203 SDHCI_TRNS_AUTO_CMD23), SDHCI_TRANSFER_MODE);
1204 }
1205 return;
1206 }
1207
1208 WARN_ON(!host->data);
1209
1210 if (!(host->quirks2 & SDHCI_QUIRK2_SUPPORT_SINGLE))
1211 mode = SDHCI_TRNS_BLK_CNT_EN;
1212
1213 if (mmc_op_multi(cmd->opcode) || data->blocks > 1) {
1214 mode = SDHCI_TRNS_BLK_CNT_EN | SDHCI_TRNS_MULTI;
1215 sdhci_auto_cmd_select(host, cmd, &mode);
1216 if (cmd->mrq->sbc && (host->flags & SDHCI_AUTO_CMD23))
1217 sdhci_writel(host, cmd->mrq->sbc->arg, SDHCI_ARGUMENT2);
1218 }
1219
1220 if (data->flags & MMC_DATA_READ)
1221 mode |= SDHCI_TRNS_READ;
1222 if (host->flags & SDHCI_REQ_USE_DMA)
1223 mode |= SDHCI_TRNS_DMA;
1224
1225 sdhci_writew(host, mode, SDHCI_TRANSFER_MODE);
1226}
1227
1228static bool sdhci_needs_reset(struct sdhci_host *host, struct mmc_request *mrq)
1229{
1230 return (!(host->flags & SDHCI_DEVICE_DEAD) &&
1231 ((mrq->cmd && mrq->cmd->error) ||
1232 (mrq->sbc && mrq->sbc->error) ||
1233 (mrq->data && mrq->data->stop && mrq->data->stop->error) ||
1234 (host->quirks & SDHCI_QUIRK_RESET_AFTER_REQUEST)));
1235}
1236
1237static void __sdhci_finish_mrq(struct sdhci_host *host, struct mmc_request *mrq)
1238{
1239 int i;
1240
1241 if (host->cmd && host->cmd->mrq == mrq)
1242 host->cmd = NULL;
1243
1244 if (host->data_cmd && host->data_cmd->mrq == mrq)
1245 host->data_cmd = NULL;
1246
1247 if (host->data && host->data->mrq == mrq)
1248 host->data = NULL;
1249
1250 if (sdhci_needs_reset(host, mrq))
1251 host->pending_reset = true;
1252
1253 for (i = 0; i < SDHCI_MAX_MRQS; i++) {
1254 if (host->mrqs_done[i] == mrq) {
1255 WARN_ON(1);
1256 return;
1257 }
1258 }
1259
1260 for (i = 0; i < SDHCI_MAX_MRQS; i++) {
1261 if (!host->mrqs_done[i]) {
1262 host->mrqs_done[i] = mrq;
1263 break;
1264 }
1265 }
1266
1267 WARN_ON(i >= SDHCI_MAX_MRQS);
1268
1269 sdhci_del_timer(host, mrq);
1270
1271 if (!sdhci_has_requests(host))
1272 sdhci_led_deactivate(host);
1273}
1274
1275static void sdhci_finish_mrq(struct sdhci_host *host, struct mmc_request *mrq)
1276{
1277 __sdhci_finish_mrq(host, mrq);
1278
1279 queue_work(host->complete_wq, &host->complete_work);
1280}
1281
1282static void sdhci_finish_data(struct sdhci_host *host)
1283{
1284 struct mmc_command *data_cmd = host->data_cmd;
1285 struct mmc_data *data = host->data;
1286
1287 host->data = NULL;
1288 host->data_cmd = NULL;
1289
1290 /*
1291 * The controller needs a reset of internal state machines upon error
1292 * conditions.
1293 */
1294 if (data->error) {
1295 if (!host->cmd || host->cmd == data_cmd)
1296 sdhci_do_reset(host, SDHCI_RESET_CMD);
1297 sdhci_do_reset(host, SDHCI_RESET_DATA);
1298 }
1299
1300 if ((host->flags & (SDHCI_REQ_USE_DMA | SDHCI_USE_ADMA)) ==
1301 (SDHCI_REQ_USE_DMA | SDHCI_USE_ADMA))
1302 sdhci_adma_table_post(host, data);
1303
1304 /*
1305 * The specification states that the block count register must
1306 * be updated, but it does not specify at what point in the
1307 * data flow. That makes the register entirely useless to read
1308 * back so we have to assume that nothing made it to the card
1309 * in the event of an error.
1310 */
1311 if (data->error)
1312 data->bytes_xfered = 0;
1313 else
1314 data->bytes_xfered = data->blksz * data->blocks;
1315
1316 /*
1317 * Need to send CMD12 if -
1318 * a) open-ended multiblock transfer (no CMD23)
1319 * b) error in multiblock transfer
1320 */
1321 if (data->stop &&
1322 (data->error ||
1323 !data->mrq->sbc)) {
1324 /*
1325 * 'cap_cmd_during_tfr' request must not use the command line
1326 * after mmc_command_done() has been called. It is upper layer's
1327 * responsibility to send the stop command if required.
1328 */
1329 if (data->mrq->cap_cmd_during_tfr) {
1330 __sdhci_finish_mrq(host, data->mrq);
1331 } else {
1332 /* Avoid triggering warning in sdhci_send_command() */
1333 host->cmd = NULL;
1334 sdhci_send_command(host, data->stop);
1335 }
1336 } else {
1337 __sdhci_finish_mrq(host, data->mrq);
1338 }
1339}
1340
1341void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd)
1342{
1343 int flags;
1344 u32 mask;
1345 unsigned long timeout;
1346
1347 WARN_ON(host->cmd);
1348
1349 /* Initially, a command has no error */
1350 cmd->error = 0;
1351
1352 if ((host->quirks2 & SDHCI_QUIRK2_STOP_WITH_TC) &&
1353 cmd->opcode == MMC_STOP_TRANSMISSION)
1354 cmd->flags |= MMC_RSP_BUSY;
1355
1356 /* Wait max 10 ms */
1357 timeout = 10;
1358
1359 mask = SDHCI_CMD_INHIBIT;
1360 if (sdhci_data_line_cmd(cmd))
1361 mask |= SDHCI_DATA_INHIBIT;
1362
1363 /* We shouldn't wait for data inihibit for stop commands, even
1364 though they might use busy signaling */
1365 if (cmd->mrq->data && (cmd == cmd->mrq->data->stop))
1366 mask &= ~SDHCI_DATA_INHIBIT;
1367
1368 while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {
1369 if (timeout == 0) {
1370 pr_err("%s: Controller never released inhibit bit(s).\n",
1371 mmc_hostname(host->mmc));
1372 sdhci_dumpregs(host);
1373 cmd->error = -EIO;
1374 sdhci_finish_mrq(host, cmd->mrq);
1375 return;
1376 }
1377 timeout--;
1378 mdelay(1);
1379 }
1380
1381 host->cmd = cmd;
1382 if (sdhci_data_line_cmd(cmd)) {
1383 WARN_ON(host->data_cmd);
1384 host->data_cmd = cmd;
1385 }
1386
1387 sdhci_prepare_data(host, cmd);
1388
1389 sdhci_writel(host, cmd->arg, SDHCI_ARGUMENT);
1390
1391 sdhci_set_transfer_mode(host, cmd);
1392
1393 if ((cmd->flags & MMC_RSP_136) && (cmd->flags & MMC_RSP_BUSY)) {
1394 pr_err("%s: Unsupported response type!\n",
1395 mmc_hostname(host->mmc));
1396 cmd->error = -EINVAL;
1397 sdhci_finish_mrq(host, cmd->mrq);
1398 return;
1399 }
1400
1401 if (!(cmd->flags & MMC_RSP_PRESENT))
1402 flags = SDHCI_CMD_RESP_NONE;
1403 else if (cmd->flags & MMC_RSP_136)
1404 flags = SDHCI_CMD_RESP_LONG;
1405 else if (cmd->flags & MMC_RSP_BUSY)
1406 flags = SDHCI_CMD_RESP_SHORT_BUSY;
1407 else
1408 flags = SDHCI_CMD_RESP_SHORT;
1409
1410 if (cmd->flags & MMC_RSP_CRC)
1411 flags |= SDHCI_CMD_CRC;
1412 if (cmd->flags & MMC_RSP_OPCODE)
1413 flags |= SDHCI_CMD_INDEX;
1414
1415 /* CMD19 is special in that the Data Present Select should be set */
1416 if (cmd->data || cmd->opcode == MMC_SEND_TUNING_BLOCK ||
1417 cmd->opcode == MMC_SEND_TUNING_BLOCK_HS200)
1418 flags |= SDHCI_CMD_DATA;
1419
1420 timeout = jiffies;
1421 if (host->data_timeout)
1422 timeout += nsecs_to_jiffies(host->data_timeout);
1423 else if (!cmd->data && cmd->busy_timeout > 9000)
1424 timeout += DIV_ROUND_UP(cmd->busy_timeout, 1000) * HZ + HZ;
1425 else
1426 timeout += 10 * HZ;
1427 sdhci_mod_timer(host, cmd->mrq, timeout);
1428
1429 sdhci_writew(host, SDHCI_MAKE_CMD(cmd->opcode, flags), SDHCI_COMMAND);
1430}
1431EXPORT_SYMBOL_GPL(sdhci_send_command);
1432
1433static void sdhci_read_rsp_136(struct sdhci_host *host, struct mmc_command *cmd)
1434{
1435 int i, reg;
1436
1437 for (i = 0; i < 4; i++) {
1438 reg = SDHCI_RESPONSE + (3 - i) * 4;
1439 cmd->resp[i] = sdhci_readl(host, reg);
1440 }
1441
1442 if (host->quirks2 & SDHCI_QUIRK2_RSP_136_HAS_CRC)
1443 return;
1444
1445 /* CRC is stripped so we need to do some shifting */
1446 for (i = 0; i < 4; i++) {
1447 cmd->resp[i] <<= 8;
1448 if (i != 3)
1449 cmd->resp[i] |= cmd->resp[i + 1] >> 24;
1450 }
1451}
1452
1453static void sdhci_finish_command(struct sdhci_host *host)
1454{
1455 struct mmc_command *cmd = host->cmd;
1456
1457 host->cmd = NULL;
1458
1459 if (cmd->flags & MMC_RSP_PRESENT) {
1460 if (cmd->flags & MMC_RSP_136) {
1461 sdhci_read_rsp_136(host, cmd);
1462 } else {
1463 cmd->resp[0] = sdhci_readl(host, SDHCI_RESPONSE);
1464 }
1465 }
1466
1467 if (cmd->mrq->cap_cmd_during_tfr && cmd == cmd->mrq->cmd)
1468 mmc_command_done(host->mmc, cmd->mrq);
1469
1470 /*
1471 * The host can send and interrupt when the busy state has
1472 * ended, allowing us to wait without wasting CPU cycles.
1473 * The busy signal uses DAT0 so this is similar to waiting
1474 * for data to complete.
1475 *
1476 * Note: The 1.0 specification is a bit ambiguous about this
1477 * feature so there might be some problems with older
1478 * controllers.
1479 */
1480 if (cmd->flags & MMC_RSP_BUSY) {
1481 if (cmd->data) {
1482 DBG("Cannot wait for busy signal when also doing a data transfer");
1483 } else if (!(host->quirks & SDHCI_QUIRK_NO_BUSY_IRQ) &&
1484 cmd == host->data_cmd) {
1485 /* Command complete before busy is ended */
1486 return;
1487 }
1488 }
1489
1490 /* Finished CMD23, now send actual command. */
1491 if (cmd == cmd->mrq->sbc) {
1492 sdhci_send_command(host, cmd->mrq->cmd);
1493 } else {
1494
1495 /* Processed actual command. */
1496 if (host->data && host->data_early)
1497 sdhci_finish_data(host);
1498
1499 if (!cmd->data)
1500 __sdhci_finish_mrq(host, cmd->mrq);
1501 }
1502}
1503
1504static u16 sdhci_get_preset_value(struct sdhci_host *host)
1505{
1506 u16 preset = 0;
1507
1508 switch (host->timing) {
1509 case MMC_TIMING_UHS_SDR12:
1510 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR12);
1511 break;
1512 case MMC_TIMING_UHS_SDR25:
1513 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR25);
1514 break;
1515 case MMC_TIMING_UHS_SDR50:
1516 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR50);
1517 break;
1518 case MMC_TIMING_UHS_SDR104:
1519 case MMC_TIMING_MMC_HS200:
1520 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR104);
1521 break;
1522 case MMC_TIMING_UHS_DDR50:
1523 case MMC_TIMING_MMC_DDR52:
1524 preset = sdhci_readw(host, SDHCI_PRESET_FOR_DDR50);
1525 break;
1526 case MMC_TIMING_MMC_HS400:
1527 preset = sdhci_readw(host, SDHCI_PRESET_FOR_HS400);
1528 break;
1529 default:
1530 pr_warn("%s: Invalid UHS-I mode selected\n",
1531 mmc_hostname(host->mmc));
1532 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR12);
1533 break;
1534 }
1535 return preset;
1536}
1537
1538u16 sdhci_calc_clk(struct sdhci_host *host, unsigned int clock,
1539 unsigned int *actual_clock)
1540{
1541 int div = 0; /* Initialized for compiler warning */
1542 int real_div = div, clk_mul = 1;
1543 u16 clk = 0;
1544 bool switch_base_clk = false;
1545
1546 if (host->version >= SDHCI_SPEC_300) {
1547 if (host->preset_enabled) {
1548 u16 pre_val;
1549
1550 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1551 pre_val = sdhci_get_preset_value(host);
1552 div = (pre_val & SDHCI_PRESET_SDCLK_FREQ_MASK)
1553 >> SDHCI_PRESET_SDCLK_FREQ_SHIFT;
1554 if (host->clk_mul &&
1555 (pre_val & SDHCI_PRESET_CLKGEN_SEL_MASK)) {
1556 clk = SDHCI_PROG_CLOCK_MODE;
1557 real_div = div + 1;
1558 clk_mul = host->clk_mul;
1559 } else {
1560 real_div = max_t(int, 1, div << 1);
1561 }
1562 goto clock_set;
1563 }
1564
1565 /*
1566 * Check if the Host Controller supports Programmable Clock
1567 * Mode.
1568 */
1569 if (host->clk_mul) {
1570 for (div = 1; div <= 1024; div++) {
1571 if ((host->max_clk * host->clk_mul / div)
1572 <= clock)
1573 break;
1574 }
1575 if ((host->max_clk * host->clk_mul / div) <= clock) {
1576 /*
1577 * Set Programmable Clock Mode in the Clock
1578 * Control register.
1579 */
1580 clk = SDHCI_PROG_CLOCK_MODE;
1581 real_div = div;
1582 clk_mul = host->clk_mul;
1583 div--;
1584 } else {
1585 /*
1586 * Divisor can be too small to reach clock
1587 * speed requirement. Then use the base clock.
1588 */
1589 switch_base_clk = true;
1590 }
1591 }
1592
1593 if (!host->clk_mul || switch_base_clk) {
1594 /* Version 3.00 divisors must be a multiple of 2. */
1595 if (host->max_clk <= clock)
1596 div = 1;
1597 else {
1598 for (div = 2; div < SDHCI_MAX_DIV_SPEC_300;
1599 div += 2) {
1600 if ((host->max_clk / div) <= clock)
1601 break;
1602 }
1603 }
1604 real_div = div;
1605 div >>= 1;
1606 if ((host->quirks2 & SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN)
1607 && !div && host->max_clk <= 25000000)
1608 div = 1;
1609 }
1610 } else {
1611 /* Version 2.00 divisors must be a power of 2. */
1612 for (div = 1; div < SDHCI_MAX_DIV_SPEC_200; div *= 2) {
1613 if ((host->max_clk / div) <= clock)
1614 break;
1615 }
1616 real_div = div;
1617 div >>= 1;
1618 }
1619
1620clock_set:
1621 if (real_div)
1622 *actual_clock = (host->max_clk * clk_mul) / real_div;
1623 clk |= (div & SDHCI_DIV_MASK) << SDHCI_DIVIDER_SHIFT;
1624 clk |= ((div & SDHCI_DIV_HI_MASK) >> SDHCI_DIV_MASK_LEN)
1625 << SDHCI_DIVIDER_HI_SHIFT;
1626
1627 return clk;
1628}
1629EXPORT_SYMBOL_GPL(sdhci_calc_clk);
1630
1631void sdhci_enable_clk(struct sdhci_host *host, u16 clk)
1632{
1633 ktime_t timeout;
1634
1635 clk |= SDHCI_CLOCK_INT_EN;
1636 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1637
1638 /* Wait max 150 ms */
1639 timeout = ktime_add_ms(ktime_get(), 150);
1640 while (1) {
1641 bool timedout = ktime_after(ktime_get(), timeout);
1642
1643 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1644 if (clk & SDHCI_CLOCK_INT_STABLE)
1645 break;
1646 if (timedout) {
1647 pr_err("%s: Internal clock never stabilised.\n",
1648 mmc_hostname(host->mmc));
1649 sdhci_dumpregs(host);
1650 return;
1651 }
1652 udelay(10);
1653 }
1654
1655 if (host->version >= SDHCI_SPEC_410 && host->v4_mode) {
1656 clk |= SDHCI_CLOCK_PLL_EN;
1657 clk &= ~SDHCI_CLOCK_INT_STABLE;
1658 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1659
1660 /* Wait max 150 ms */
1661 timeout = ktime_add_ms(ktime_get(), 150);
1662 while (1) {
1663 bool timedout = ktime_after(ktime_get(), timeout);
1664
1665 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1666 if (clk & SDHCI_CLOCK_INT_STABLE)
1667 break;
1668 if (timedout) {
1669 pr_err("%s: PLL clock never stabilised.\n",
1670 mmc_hostname(host->mmc));
1671 sdhci_dumpregs(host);
1672 return;
1673 }
1674 udelay(10);
1675 }
1676 }
1677
1678 clk |= SDHCI_CLOCK_CARD_EN;
1679 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1680}
1681EXPORT_SYMBOL_GPL(sdhci_enable_clk);
1682
1683void sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
1684{
1685 u16 clk;
1686
1687 host->mmc->actual_clock = 0;
1688
1689 sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
1690
1691 if (clock == 0)
1692 return;
1693
1694 clk = sdhci_calc_clk(host, clock, &host->mmc->actual_clock);
1695 sdhci_enable_clk(host, clk);
1696}
1697EXPORT_SYMBOL_GPL(sdhci_set_clock);
1698
1699static void sdhci_set_power_reg(struct sdhci_host *host, unsigned char mode,
1700 unsigned short vdd)
1701{
1702 struct mmc_host *mmc = host->mmc;
1703
1704 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd);
1705
1706 if (mode != MMC_POWER_OFF)
1707 sdhci_writeb(host, SDHCI_POWER_ON, SDHCI_POWER_CONTROL);
1708 else
1709 sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
1710}
1711
1712void sdhci_set_power_noreg(struct sdhci_host *host, unsigned char mode,
1713 unsigned short vdd)
1714{
1715 u8 pwr = 0;
1716
1717 if (mode != MMC_POWER_OFF) {
1718 switch (1 << vdd) {
1719 case MMC_VDD_165_195:
1720 /*
1721 * Without a regulator, SDHCI does not support 2.0v
1722 * so we only get here if the driver deliberately
1723 * added the 2.0v range to ocr_avail. Map it to 1.8v
1724 * for the purpose of turning on the power.
1725 */
1726 case MMC_VDD_20_21:
1727 pwr = SDHCI_POWER_180;
1728 break;
1729 case MMC_VDD_29_30:
1730 case MMC_VDD_30_31:
1731 pwr = SDHCI_POWER_300;
1732 break;
1733 case MMC_VDD_32_33:
1734 case MMC_VDD_33_34:
1735 pwr = SDHCI_POWER_330;
1736 break;
1737 default:
1738 WARN(1, "%s: Invalid vdd %#x\n",
1739 mmc_hostname(host->mmc), vdd);
1740 break;
1741 }
1742 }
1743
1744 if (host->pwr == pwr)
1745 return;
1746
1747 host->pwr = pwr;
1748
1749 if (pwr == 0) {
1750 sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
1751 if (host->quirks2 & SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON)
1752 sdhci_runtime_pm_bus_off(host);
1753 } else {
1754 /*
1755 * Spec says that we should clear the power reg before setting
1756 * a new value. Some controllers don't seem to like this though.
1757 */
1758 if (!(host->quirks & SDHCI_QUIRK_SINGLE_POWER_WRITE))
1759 sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
1760
1761 /*
1762 * At least the Marvell CaFe chip gets confused if we set the
1763 * voltage and set turn on power at the same time, so set the
1764 * voltage first.
1765 */
1766 if (host->quirks & SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER)
1767 sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
1768
1769 pwr |= SDHCI_POWER_ON;
1770
1771 sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
1772
1773 if (host->quirks2 & SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON)
1774 sdhci_runtime_pm_bus_on(host);
1775
1776 /*
1777 * Some controllers need an extra 10ms delay of 10ms before
1778 * they can apply clock after applying power
1779 */
1780 if (host->quirks & SDHCI_QUIRK_DELAY_AFTER_POWER)
1781 mdelay(10);
1782 }
1783}
1784EXPORT_SYMBOL_GPL(sdhci_set_power_noreg);
1785
1786void sdhci_set_power(struct sdhci_host *host, unsigned char mode,
1787 unsigned short vdd)
1788{
1789 if (IS_ERR(host->mmc->supply.vmmc))
1790 sdhci_set_power_noreg(host, mode, vdd);
1791 else
1792 sdhci_set_power_reg(host, mode, vdd);
1793}
1794EXPORT_SYMBOL_GPL(sdhci_set_power);
1795
1796/*****************************************************************************\
1797 * *
1798 * MMC callbacks *
1799 * *
1800\*****************************************************************************/
1801
1802void sdhci_request(struct mmc_host *mmc, struct mmc_request *mrq)
1803{
1804 struct sdhci_host *host;
1805 int present;
1806 unsigned long flags;
1807
1808 host = mmc_priv(mmc);
1809
1810 /* Firstly check card presence */
1811 present = mmc->ops->get_cd(mmc);
1812
1813 spin_lock_irqsave(&host->lock, flags);
1814
1815 sdhci_led_activate(host);
1816
1817 /*
1818 * Ensure we don't send the STOP for non-SET_BLOCK_COUNTED
1819 * requests if Auto-CMD12 is enabled.
1820 */
1821 if (sdhci_auto_cmd12(host, mrq)) {
1822 if (mrq->stop) {
1823 mrq->data->stop = NULL;
1824 mrq->stop = NULL;
1825 }
1826 }
1827
1828 if (!present || host->flags & SDHCI_DEVICE_DEAD) {
1829 mrq->cmd->error = -ENOMEDIUM;
1830 sdhci_finish_mrq(host, mrq);
1831 } else {
1832 if (mrq->sbc && !(host->flags & SDHCI_AUTO_CMD23))
1833 sdhci_send_command(host, mrq->sbc);
1834 else
1835 sdhci_send_command(host, mrq->cmd);
1836 }
1837
1838 spin_unlock_irqrestore(&host->lock, flags);
1839}
1840EXPORT_SYMBOL_GPL(sdhci_request);
1841
1842void sdhci_set_bus_width(struct sdhci_host *host, int width)
1843{
1844 u8 ctrl;
1845
1846 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
1847 if (width == MMC_BUS_WIDTH_8) {
1848 ctrl &= ~SDHCI_CTRL_4BITBUS;
1849 ctrl |= SDHCI_CTRL_8BITBUS;
1850 } else {
1851 if (host->mmc->caps & MMC_CAP_8_BIT_DATA)
1852 ctrl &= ~SDHCI_CTRL_8BITBUS;
1853 if (width == MMC_BUS_WIDTH_4)
1854 ctrl |= SDHCI_CTRL_4BITBUS;
1855 else
1856 ctrl &= ~SDHCI_CTRL_4BITBUS;
1857 }
1858 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
1859}
1860EXPORT_SYMBOL_GPL(sdhci_set_bus_width);
1861
1862void sdhci_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
1863{
1864 u16 ctrl_2;
1865
1866 ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1867 /* Select Bus Speed Mode for host */
1868 ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
1869 if ((timing == MMC_TIMING_MMC_HS200) ||
1870 (timing == MMC_TIMING_UHS_SDR104))
1871 ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
1872 else if (timing == MMC_TIMING_UHS_SDR12)
1873 ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
1874 else if (timing == MMC_TIMING_SD_HS ||
1875 timing == MMC_TIMING_MMC_HS ||
1876 timing == MMC_TIMING_UHS_SDR25)
1877 ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
1878 else if (timing == MMC_TIMING_UHS_SDR50)
1879 ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
1880 else if ((timing == MMC_TIMING_UHS_DDR50) ||
1881 (timing == MMC_TIMING_MMC_DDR52))
1882 ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
1883 else if (timing == MMC_TIMING_MMC_HS400)
1884 ctrl_2 |= SDHCI_CTRL_HS400; /* Non-standard */
1885 sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
1886}
1887EXPORT_SYMBOL_GPL(sdhci_set_uhs_signaling);
1888
1889void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
1890{
1891 struct sdhci_host *host = mmc_priv(mmc);
1892 u8 ctrl;
1893
1894 if (ios->power_mode == MMC_POWER_UNDEFINED)
1895 return;
1896
1897 if (host->flags & SDHCI_DEVICE_DEAD) {
1898 if (!IS_ERR(mmc->supply.vmmc) &&
1899 ios->power_mode == MMC_POWER_OFF)
1900 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
1901 return;
1902 }
1903
1904 /*
1905 * Reset the chip on each power off.
1906 * Should clear out any weird states.
1907 */
1908 if (ios->power_mode == MMC_POWER_OFF) {
1909 sdhci_writel(host, 0, SDHCI_SIGNAL_ENABLE);
1910 sdhci_reinit(host);
1911 }
1912
1913 if (host->version >= SDHCI_SPEC_300 &&
1914 (ios->power_mode == MMC_POWER_UP) &&
1915 !(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN))
1916 sdhci_enable_preset_value(host, false);
1917
1918 if (!ios->clock || ios->clock != host->clock) {
1919 host->ops->set_clock(host, ios->clock);
1920 host->clock = ios->clock;
1921
1922 if (host->quirks & SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK &&
1923 host->clock) {
1924 host->timeout_clk = host->mmc->actual_clock ?
1925 host->mmc->actual_clock / 1000 :
1926 host->clock / 1000;
1927 host->mmc->max_busy_timeout =
1928 host->ops->get_max_timeout_count ?
1929 host->ops->get_max_timeout_count(host) :
1930 1 << 27;
1931 host->mmc->max_busy_timeout /= host->timeout_clk;
1932 }
1933 }
1934
1935 if (host->ops->set_power)
1936 host->ops->set_power(host, ios->power_mode, ios->vdd);
1937 else
1938 sdhci_set_power(host, ios->power_mode, ios->vdd);
1939
1940 if (host->ops->platform_send_init_74_clocks)
1941 host->ops->platform_send_init_74_clocks(host, ios->power_mode);
1942
1943 host->ops->set_bus_width(host, ios->bus_width);
1944
1945 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
1946
1947 if (!(host->quirks & SDHCI_QUIRK_NO_HISPD_BIT)) {
1948 if (ios->timing == MMC_TIMING_SD_HS ||
1949 ios->timing == MMC_TIMING_MMC_HS ||
1950 ios->timing == MMC_TIMING_MMC_HS400 ||
1951 ios->timing == MMC_TIMING_MMC_HS200 ||
1952 ios->timing == MMC_TIMING_MMC_DDR52 ||
1953 ios->timing == MMC_TIMING_UHS_SDR50 ||
1954 ios->timing == MMC_TIMING_UHS_SDR104 ||
1955 ios->timing == MMC_TIMING_UHS_DDR50 ||
1956 ios->timing == MMC_TIMING_UHS_SDR25)
1957 ctrl |= SDHCI_CTRL_HISPD;
1958 else
1959 ctrl &= ~SDHCI_CTRL_HISPD;
1960 }
1961
1962 if (host->version >= SDHCI_SPEC_300) {
1963 u16 clk, ctrl_2;
1964
1965 if (!host->preset_enabled) {
1966 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
1967 /*
1968 * We only need to set Driver Strength if the
1969 * preset value enable is not set.
1970 */
1971 ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1972 ctrl_2 &= ~SDHCI_CTRL_DRV_TYPE_MASK;
1973 if (ios->drv_type == MMC_SET_DRIVER_TYPE_A)
1974 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_A;
1975 else if (ios->drv_type == MMC_SET_DRIVER_TYPE_B)
1976 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_B;
1977 else if (ios->drv_type == MMC_SET_DRIVER_TYPE_C)
1978 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_C;
1979 else if (ios->drv_type == MMC_SET_DRIVER_TYPE_D)
1980 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_D;
1981 else {
1982 pr_warn("%s: invalid driver type, default to driver type B\n",
1983 mmc_hostname(mmc));
1984 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_B;
1985 }
1986
1987 sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
1988 } else {
1989 /*
1990 * According to SDHC Spec v3.00, if the Preset Value
1991 * Enable in the Host Control 2 register is set, we
1992 * need to reset SD Clock Enable before changing High
1993 * Speed Enable to avoid generating clock gliches.
1994 */
1995
1996 /* Reset SD Clock Enable */
1997 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1998 clk &= ~SDHCI_CLOCK_CARD_EN;
1999 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
2000
2001 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
2002
2003 /* Re-enable SD Clock */
2004 host->ops->set_clock(host, host->clock);
2005 }
2006
2007 /* Reset SD Clock Enable */
2008 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
2009 clk &= ~SDHCI_CLOCK_CARD_EN;
2010 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
2011
2012 host->ops->set_uhs_signaling(host, ios->timing);
2013 host->timing = ios->timing;
2014
2015 if (!(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN) &&
2016 ((ios->timing == MMC_TIMING_UHS_SDR12) ||
2017 (ios->timing == MMC_TIMING_UHS_SDR25) ||
2018 (ios->timing == MMC_TIMING_UHS_SDR50) ||
2019 (ios->timing == MMC_TIMING_UHS_SDR104) ||
2020 (ios->timing == MMC_TIMING_UHS_DDR50) ||
2021 (ios->timing == MMC_TIMING_MMC_DDR52))) {
2022 u16 preset;
2023
2024 sdhci_enable_preset_value(host, true);
2025 preset = sdhci_get_preset_value(host);
2026 ios->drv_type = (preset & SDHCI_PRESET_DRV_MASK)
2027 >> SDHCI_PRESET_DRV_SHIFT;
2028 }
2029
2030 /* Re-enable SD Clock */
2031 host->ops->set_clock(host, host->clock);
2032 } else
2033 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
2034
2035 /*
2036 * Some (ENE) controllers go apeshit on some ios operation,
2037 * signalling timeout and CRC errors even on CMD0. Resetting
2038 * it on each ios seems to solve the problem.
2039 */
2040 if (host->quirks & SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS)
2041 sdhci_do_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA);
2042}
2043EXPORT_SYMBOL_GPL(sdhci_set_ios);
2044
2045static int sdhci_get_cd(struct mmc_host *mmc)
2046{
2047 struct sdhci_host *host = mmc_priv(mmc);
2048 int gpio_cd = mmc_gpio_get_cd(mmc);
2049
2050 if (host->flags & SDHCI_DEVICE_DEAD)
2051 return 0;
2052
2053 /* If nonremovable, assume that the card is always present. */
2054 if (!mmc_card_is_removable(host->mmc))
2055 return 1;
2056
2057 /*
2058 * Try slot gpio detect, if defined it take precedence
2059 * over build in controller functionality
2060 */
2061 if (gpio_cd >= 0)
2062 return !!gpio_cd;
2063
2064 /* If polling, assume that the card is always present. */
2065 if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
2066 return 1;
2067
2068 /* Host native card detect */
2069 return !!(sdhci_readl(host, SDHCI_PRESENT_STATE) & SDHCI_CARD_PRESENT);
2070}
2071
2072static int sdhci_check_ro(struct sdhci_host *host)
2073{
2074 unsigned long flags;
2075 int is_readonly;
2076
2077 spin_lock_irqsave(&host->lock, flags);
2078
2079 if (host->flags & SDHCI_DEVICE_DEAD)
2080 is_readonly = 0;
2081 else if (host->ops->get_ro)
2082 is_readonly = host->ops->get_ro(host);
2083 else if (mmc_can_gpio_ro(host->mmc))
2084 is_readonly = mmc_gpio_get_ro(host->mmc);
2085 else
2086 is_readonly = !(sdhci_readl(host, SDHCI_PRESENT_STATE)
2087 & SDHCI_WRITE_PROTECT);
2088
2089 spin_unlock_irqrestore(&host->lock, flags);
2090
2091 /* This quirk needs to be replaced by a callback-function later */
2092 return host->quirks & SDHCI_QUIRK_INVERTED_WRITE_PROTECT ?
2093 !is_readonly : is_readonly;
2094}
2095
2096#define SAMPLE_COUNT 5
2097
2098static int sdhci_get_ro(struct mmc_host *mmc)
2099{
2100 struct sdhci_host *host = mmc_priv(mmc);
2101 int i, ro_count;
2102
2103 if (!(host->quirks & SDHCI_QUIRK_UNSTABLE_RO_DETECT))
2104 return sdhci_check_ro(host);
2105
2106 ro_count = 0;
2107 for (i = 0; i < SAMPLE_COUNT; i++) {
2108 if (sdhci_check_ro(host)) {
2109 if (++ro_count > SAMPLE_COUNT / 2)
2110 return 1;
2111 }
2112 msleep(30);
2113 }
2114 return 0;
2115}
2116
2117static void sdhci_hw_reset(struct mmc_host *mmc)
2118{
2119 struct sdhci_host *host = mmc_priv(mmc);
2120
2121 if (host->ops && host->ops->hw_reset)
2122 host->ops->hw_reset(host);
2123}
2124
2125static void sdhci_enable_sdio_irq_nolock(struct sdhci_host *host, int enable)
2126{
2127 if (!(host->flags & SDHCI_DEVICE_DEAD)) {
2128 if (enable)
2129 host->ier |= SDHCI_INT_CARD_INT;
2130 else
2131 host->ier &= ~SDHCI_INT_CARD_INT;
2132
2133 sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
2134 sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
2135 }
2136}
2137
2138void sdhci_enable_sdio_irq(struct mmc_host *mmc, int enable)
2139{
2140 struct sdhci_host *host = mmc_priv(mmc);
2141 unsigned long flags;
2142
2143 if (enable)
2144 pm_runtime_get_noresume(host->mmc->parent);
2145
2146 spin_lock_irqsave(&host->lock, flags);
2147 sdhci_enable_sdio_irq_nolock(host, enable);
2148 spin_unlock_irqrestore(&host->lock, flags);
2149
2150 if (!enable)
2151 pm_runtime_put_noidle(host->mmc->parent);
2152}
2153EXPORT_SYMBOL_GPL(sdhci_enable_sdio_irq);
2154
2155static void sdhci_ack_sdio_irq(struct mmc_host *mmc)
2156{
2157 struct sdhci_host *host = mmc_priv(mmc);
2158 unsigned long flags;
2159
2160 spin_lock_irqsave(&host->lock, flags);
2161 sdhci_enable_sdio_irq_nolock(host, true);
2162 spin_unlock_irqrestore(&host->lock, flags);
2163}
2164
2165int sdhci_start_signal_voltage_switch(struct mmc_host *mmc,
2166 struct mmc_ios *ios)
2167{
2168 struct sdhci_host *host = mmc_priv(mmc);
2169 u16 ctrl;
2170 int ret;
2171
2172 /*
2173 * Signal Voltage Switching is only applicable for Host Controllers
2174 * v3.00 and above.
2175 */
2176 if (host->version < SDHCI_SPEC_300)
2177 return 0;
2178
2179 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2180
2181 switch (ios->signal_voltage) {
2182 case MMC_SIGNAL_VOLTAGE_330:
2183 if (!(host->flags & SDHCI_SIGNALING_330))
2184 return -EINVAL;
2185 /* Set 1.8V Signal Enable in the Host Control2 register to 0 */
2186 ctrl &= ~SDHCI_CTRL_VDD_180;
2187 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2188
2189 if (!IS_ERR(mmc->supply.vqmmc)) {
2190 ret = mmc_regulator_set_vqmmc(mmc, ios);
2191 if (ret) {
2192 pr_warn("%s: Switching to 3.3V signalling voltage failed\n",
2193 mmc_hostname(mmc));
2194 return -EIO;
2195 }
2196 }
2197 /* Wait for 5ms */
2198 usleep_range(5000, 5500);
2199
2200 /* 3.3V regulator output should be stable within 5 ms */
2201 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2202 if (!(ctrl & SDHCI_CTRL_VDD_180))
2203 return 0;
2204
2205 pr_warn("%s: 3.3V regulator output did not became stable\n",
2206 mmc_hostname(mmc));
2207
2208 return -EAGAIN;
2209 case MMC_SIGNAL_VOLTAGE_180:
2210 if (!(host->flags & SDHCI_SIGNALING_180))
2211 return -EINVAL;
2212 if (!IS_ERR(mmc->supply.vqmmc)) {
2213 ret = mmc_regulator_set_vqmmc(mmc, ios);
2214 if (ret) {
2215 pr_warn("%s: Switching to 1.8V signalling voltage failed\n",
2216 mmc_hostname(mmc));
2217 return -EIO;
2218 }
2219 }
2220
2221 /*
2222 * Enable 1.8V Signal Enable in the Host Control2
2223 * register
2224 */
2225 ctrl |= SDHCI_CTRL_VDD_180;
2226 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2227
2228 /* Some controller need to do more when switching */
2229 if (host->ops->voltage_switch)
2230 host->ops->voltage_switch(host);
2231
2232 /* 1.8V regulator output should be stable within 5 ms */
2233 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2234 if (ctrl & SDHCI_CTRL_VDD_180)
2235 return 0;
2236
2237 pr_warn("%s: 1.8V regulator output did not became stable\n",
2238 mmc_hostname(mmc));
2239
2240 return -EAGAIN;
2241 case MMC_SIGNAL_VOLTAGE_120:
2242 if (!(host->flags & SDHCI_SIGNALING_120))
2243 return -EINVAL;
2244 if (!IS_ERR(mmc->supply.vqmmc)) {
2245 ret = mmc_regulator_set_vqmmc(mmc, ios);
2246 if (ret) {
2247 pr_warn("%s: Switching to 1.2V signalling voltage failed\n",
2248 mmc_hostname(mmc));
2249 return -EIO;
2250 }
2251 }
2252 return 0;
2253 default:
2254 /* No signal voltage switch required */
2255 return 0;
2256 }
2257}
2258EXPORT_SYMBOL_GPL(sdhci_start_signal_voltage_switch);
2259
2260static int sdhci_card_busy(struct mmc_host *mmc)
2261{
2262 struct sdhci_host *host = mmc_priv(mmc);
2263 u32 present_state;
2264
2265 /* Check whether DAT[0] is 0 */
2266 present_state = sdhci_readl(host, SDHCI_PRESENT_STATE);
2267
2268 return !(present_state & SDHCI_DATA_0_LVL_MASK);
2269}
2270
2271static int sdhci_prepare_hs400_tuning(struct mmc_host *mmc, struct mmc_ios *ios)
2272{
2273 struct sdhci_host *host = mmc_priv(mmc);
2274 unsigned long flags;
2275
2276 spin_lock_irqsave(&host->lock, flags);
2277 host->flags |= SDHCI_HS400_TUNING;
2278 spin_unlock_irqrestore(&host->lock, flags);
2279
2280 return 0;
2281}
2282
2283void sdhci_start_tuning(struct sdhci_host *host)
2284{
2285 u16 ctrl;
2286
2287 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2288 ctrl |= SDHCI_CTRL_EXEC_TUNING;
2289 if (host->quirks2 & SDHCI_QUIRK2_TUNING_WORK_AROUND)
2290 ctrl |= SDHCI_CTRL_TUNED_CLK;
2291 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2292
2293 /*
2294 * As per the Host Controller spec v3.00, tuning command
2295 * generates Buffer Read Ready interrupt, so enable that.
2296 *
2297 * Note: The spec clearly says that when tuning sequence
2298 * is being performed, the controller does not generate
2299 * interrupts other than Buffer Read Ready interrupt. But
2300 * to make sure we don't hit a controller bug, we _only_
2301 * enable Buffer Read Ready interrupt here.
2302 */
2303 sdhci_writel(host, SDHCI_INT_DATA_AVAIL, SDHCI_INT_ENABLE);
2304 sdhci_writel(host, SDHCI_INT_DATA_AVAIL, SDHCI_SIGNAL_ENABLE);
2305}
2306EXPORT_SYMBOL_GPL(sdhci_start_tuning);
2307
2308void sdhci_end_tuning(struct sdhci_host *host)
2309{
2310 sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
2311 sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
2312}
2313EXPORT_SYMBOL_GPL(sdhci_end_tuning);
2314
2315void sdhci_reset_tuning(struct sdhci_host *host)
2316{
2317 u16 ctrl;
2318
2319 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2320 ctrl &= ~SDHCI_CTRL_TUNED_CLK;
2321 ctrl &= ~SDHCI_CTRL_EXEC_TUNING;
2322 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2323}
2324EXPORT_SYMBOL_GPL(sdhci_reset_tuning);
2325
2326void sdhci_abort_tuning(struct sdhci_host *host, u32 opcode)
2327{
2328 sdhci_reset_tuning(host);
2329
2330 sdhci_do_reset(host, SDHCI_RESET_CMD);
2331 sdhci_do_reset(host, SDHCI_RESET_DATA);
2332
2333 sdhci_end_tuning(host);
2334
2335 mmc_abort_tuning(host->mmc, opcode);
2336}
2337EXPORT_SYMBOL_GPL(sdhci_abort_tuning);
2338
2339/*
2340 * We use sdhci_send_tuning() because mmc_send_tuning() is not a good fit. SDHCI
2341 * tuning command does not have a data payload (or rather the hardware does it
2342 * automatically) so mmc_send_tuning() will return -EIO. Also the tuning command
2343 * interrupt setup is different to other commands and there is no timeout
2344 * interrupt so special handling is needed.
2345 */
2346void sdhci_send_tuning(struct sdhci_host *host, u32 opcode)
2347{
2348 struct mmc_host *mmc = host->mmc;
2349 struct mmc_command cmd = {};
2350 struct mmc_request mrq = {};
2351 unsigned long flags;
2352 u32 b = host->sdma_boundary;
2353
2354 spin_lock_irqsave(&host->lock, flags);
2355
2356 cmd.opcode = opcode;
2357 cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
2358 cmd.mrq = &mrq;
2359
2360 mrq.cmd = &cmd;
2361 /*
2362 * In response to CMD19, the card sends 64 bytes of tuning
2363 * block to the Host Controller. So we set the block size
2364 * to 64 here.
2365 */
2366 if (cmd.opcode == MMC_SEND_TUNING_BLOCK_HS200 &&
2367 mmc->ios.bus_width == MMC_BUS_WIDTH_8)
2368 sdhci_writew(host, SDHCI_MAKE_BLKSZ(b, 128), SDHCI_BLOCK_SIZE);
2369 else
2370 sdhci_writew(host, SDHCI_MAKE_BLKSZ(b, 64), SDHCI_BLOCK_SIZE);
2371
2372 /*
2373 * The tuning block is sent by the card to the host controller.
2374 * So we set the TRNS_READ bit in the Transfer Mode register.
2375 * This also takes care of setting DMA Enable and Multi Block
2376 * Select in the same register to 0.
2377 */
2378 sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE);
2379
2380 sdhci_send_command(host, &cmd);
2381
2382 host->cmd = NULL;
2383
2384 sdhci_del_timer(host, &mrq);
2385
2386 host->tuning_done = 0;
2387
2388 spin_unlock_irqrestore(&host->lock, flags);
2389
2390 /* Wait for Buffer Read Ready interrupt */
2391 wait_event_timeout(host->buf_ready_int, (host->tuning_done == 1),
2392 msecs_to_jiffies(50));
2393
2394}
2395EXPORT_SYMBOL_GPL(sdhci_send_tuning);
2396
2397static int __sdhci_execute_tuning(struct sdhci_host *host, u32 opcode)
2398{
2399 int i;
2400
2401 /*
2402 * Issue opcode repeatedly till Execute Tuning is set to 0 or the number
2403 * of loops reaches tuning loop count.
2404 */
2405 for (i = 0; i < host->tuning_loop_count; i++) {
2406 u16 ctrl;
2407
2408 sdhci_send_tuning(host, opcode);
2409
2410 if (!host->tuning_done) {
2411 pr_info("%s: Tuning timeout, falling back to fixed sampling clock\n",
2412 mmc_hostname(host->mmc));
2413 sdhci_abort_tuning(host, opcode);
2414 return -ETIMEDOUT;
2415 }
2416
2417 /* Spec does not require a delay between tuning cycles */
2418 if (host->tuning_delay > 0)
2419 mdelay(host->tuning_delay);
2420
2421 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2422 if (!(ctrl & SDHCI_CTRL_EXEC_TUNING)) {
2423 if (ctrl & SDHCI_CTRL_TUNED_CLK)
2424 return 0; /* Success! */
2425 break;
2426 }
2427
2428 }
2429
2430 pr_info("%s: Tuning failed, falling back to fixed sampling clock\n",
2431 mmc_hostname(host->mmc));
2432 sdhci_reset_tuning(host);
2433 return -EAGAIN;
2434}
2435
2436int sdhci_execute_tuning(struct mmc_host *mmc, u32 opcode)
2437{
2438 struct sdhci_host *host = mmc_priv(mmc);
2439 int err = 0;
2440 unsigned int tuning_count = 0;
2441 bool hs400_tuning;
2442
2443 hs400_tuning = host->flags & SDHCI_HS400_TUNING;
2444
2445 if (host->tuning_mode == SDHCI_TUNING_MODE_1)
2446 tuning_count = host->tuning_count;
2447
2448 /*
2449 * The Host Controller needs tuning in case of SDR104 and DDR50
2450 * mode, and for SDR50 mode when Use Tuning for SDR50 is set in
2451 * the Capabilities register.
2452 * If the Host Controller supports the HS200 mode then the
2453 * tuning function has to be executed.
2454 */
2455 switch (host->timing) {
2456 /* HS400 tuning is done in HS200 mode */
2457 case MMC_TIMING_MMC_HS400:
2458 err = -EINVAL;
2459 goto out;
2460
2461 case MMC_TIMING_MMC_HS200:
2462 /*
2463 * Periodic re-tuning for HS400 is not expected to be needed, so
2464 * disable it here.
2465 */
2466 if (hs400_tuning)
2467 tuning_count = 0;
2468 break;
2469
2470 case MMC_TIMING_UHS_SDR104:
2471 case MMC_TIMING_UHS_DDR50:
2472 break;
2473
2474 case MMC_TIMING_UHS_SDR50:
2475 if (host->flags & SDHCI_SDR50_NEEDS_TUNING)
2476 break;
2477 /* FALLTHROUGH */
2478
2479 default:
2480 goto out;
2481 }
2482
2483 if (host->ops->platform_execute_tuning) {
2484 err = host->ops->platform_execute_tuning(host, opcode);
2485 goto out;
2486 }
2487
2488 host->mmc->retune_period = tuning_count;
2489
2490 if (host->tuning_delay < 0)
2491 host->tuning_delay = opcode == MMC_SEND_TUNING_BLOCK;
2492
2493 sdhci_start_tuning(host);
2494
2495 host->tuning_err = __sdhci_execute_tuning(host, opcode);
2496
2497 sdhci_end_tuning(host);
2498out:
2499 host->flags &= ~SDHCI_HS400_TUNING;
2500
2501 return err;
2502}
2503EXPORT_SYMBOL_GPL(sdhci_execute_tuning);
2504
2505static void sdhci_enable_preset_value(struct sdhci_host *host, bool enable)
2506{
2507 /* Host Controller v3.00 defines preset value registers */
2508 if (host->version < SDHCI_SPEC_300)
2509 return;
2510
2511 /*
2512 * We only enable or disable Preset Value if they are not already
2513 * enabled or disabled respectively. Otherwise, we bail out.
2514 */
2515 if (host->preset_enabled != enable) {
2516 u16 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2517
2518 if (enable)
2519 ctrl |= SDHCI_CTRL_PRESET_VAL_ENABLE;
2520 else
2521 ctrl &= ~SDHCI_CTRL_PRESET_VAL_ENABLE;
2522
2523 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2524
2525 if (enable)
2526 host->flags |= SDHCI_PV_ENABLED;
2527 else
2528 host->flags &= ~SDHCI_PV_ENABLED;
2529
2530 host->preset_enabled = enable;
2531 }
2532}
2533
2534static void sdhci_post_req(struct mmc_host *mmc, struct mmc_request *mrq,
2535 int err)
2536{
2537 struct sdhci_host *host = mmc_priv(mmc);
2538 struct mmc_data *data = mrq->data;
2539
2540 if (data->host_cookie != COOKIE_UNMAPPED)
2541 dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
2542 mmc_get_dma_dir(data));
2543
2544 data->host_cookie = COOKIE_UNMAPPED;
2545}
2546
2547static void sdhci_pre_req(struct mmc_host *mmc, struct mmc_request *mrq)
2548{
2549 struct sdhci_host *host = mmc_priv(mmc);
2550
2551 mrq->data->host_cookie = COOKIE_UNMAPPED;
2552
2553 /*
2554 * No pre-mapping in the pre hook if we're using the bounce buffer,
2555 * for that we would need two bounce buffers since one buffer is
2556 * in flight when this is getting called.
2557 */
2558 if (host->flags & SDHCI_REQ_USE_DMA && !host->bounce_buffer)
2559 sdhci_pre_dma_transfer(host, mrq->data, COOKIE_PRE_MAPPED);
2560}
2561
2562static void sdhci_error_out_mrqs(struct sdhci_host *host, int err)
2563{
2564 if (host->data_cmd) {
2565 host->data_cmd->error = err;
2566 sdhci_finish_mrq(host, host->data_cmd->mrq);
2567 }
2568
2569 if (host->cmd) {
2570 host->cmd->error = err;
2571 sdhci_finish_mrq(host, host->cmd->mrq);
2572 }
2573}
2574
2575static void sdhci_card_event(struct mmc_host *mmc)
2576{
2577 struct sdhci_host *host = mmc_priv(mmc);
2578 unsigned long flags;
2579 int present;
2580
2581 /* First check if client has provided their own card event */
2582 if (host->ops->card_event)
2583 host->ops->card_event(host);
2584
2585 present = mmc->ops->get_cd(mmc);
2586
2587 spin_lock_irqsave(&host->lock, flags);
2588
2589 /* Check sdhci_has_requests() first in case we are runtime suspended */
2590 if (sdhci_has_requests(host) && !present) {
2591 pr_err("%s: Card removed during transfer!\n",
2592 mmc_hostname(host->mmc));
2593 pr_err("%s: Resetting controller.\n",
2594 mmc_hostname(host->mmc));
2595
2596 sdhci_do_reset(host, SDHCI_RESET_CMD);
2597 sdhci_do_reset(host, SDHCI_RESET_DATA);
2598
2599 sdhci_error_out_mrqs(host, -ENOMEDIUM);
2600 }
2601
2602 spin_unlock_irqrestore(&host->lock, flags);
2603}
2604
2605static const struct mmc_host_ops sdhci_ops = {
2606 .request = sdhci_request,
2607 .post_req = sdhci_post_req,
2608 .pre_req = sdhci_pre_req,
2609 .set_ios = sdhci_set_ios,
2610 .get_cd = sdhci_get_cd,
2611 .get_ro = sdhci_get_ro,
2612 .hw_reset = sdhci_hw_reset,
2613 .enable_sdio_irq = sdhci_enable_sdio_irq,
2614 .ack_sdio_irq = sdhci_ack_sdio_irq,
2615 .start_signal_voltage_switch = sdhci_start_signal_voltage_switch,
2616 .prepare_hs400_tuning = sdhci_prepare_hs400_tuning,
2617 .execute_tuning = sdhci_execute_tuning,
2618 .card_event = sdhci_card_event,
2619 .card_busy = sdhci_card_busy,
2620};
2621
2622/*****************************************************************************\
2623 * *
2624 * Request done *
2625 * *
2626\*****************************************************************************/
2627
2628static bool sdhci_request_done(struct sdhci_host *host)
2629{
2630 unsigned long flags;
2631 struct mmc_request *mrq;
2632 int i;
2633
2634 spin_lock_irqsave(&host->lock, flags);
2635
2636 for (i = 0; i < SDHCI_MAX_MRQS; i++) {
2637 mrq = host->mrqs_done[i];
2638 if (mrq)
2639 break;
2640 }
2641
2642 if (!mrq) {
2643 spin_unlock_irqrestore(&host->lock, flags);
2644 return true;
2645 }
2646
2647 /*
2648 * Always unmap the data buffers if they were mapped by
2649 * sdhci_prepare_data() whenever we finish with a request.
2650 * This avoids leaking DMA mappings on error.
2651 */
2652 if (host->flags & SDHCI_REQ_USE_DMA) {
2653 struct mmc_data *data = mrq->data;
2654
2655 if (data && data->host_cookie == COOKIE_MAPPED) {
2656 if (host->bounce_buffer) {
2657 /*
2658 * On reads, copy the bounced data into the
2659 * sglist
2660 */
2661 if (mmc_get_dma_dir(data) == DMA_FROM_DEVICE) {
2662 unsigned int length = data->bytes_xfered;
2663
2664 if (length > host->bounce_buffer_size) {
2665 pr_err("%s: bounce buffer is %u bytes but DMA claims to have transferred %u bytes\n",
2666 mmc_hostname(host->mmc),
2667 host->bounce_buffer_size,
2668 data->bytes_xfered);
2669 /* Cap it down and continue */
2670 length = host->bounce_buffer_size;
2671 }
2672 dma_sync_single_for_cpu(
2673 host->mmc->parent,
2674 host->bounce_addr,
2675 host->bounce_buffer_size,
2676 DMA_FROM_DEVICE);
2677 sg_copy_from_buffer(data->sg,
2678 data->sg_len,
2679 host->bounce_buffer,
2680 length);
2681 } else {
2682 /* No copying, just switch ownership */
2683 dma_sync_single_for_cpu(
2684 host->mmc->parent,
2685 host->bounce_addr,
2686 host->bounce_buffer_size,
2687 mmc_get_dma_dir(data));
2688 }
2689 } else {
2690 /* Unmap the raw data */
2691 dma_unmap_sg(mmc_dev(host->mmc), data->sg,
2692 data->sg_len,
2693 mmc_get_dma_dir(data));
2694 }
2695 data->host_cookie = COOKIE_UNMAPPED;
2696 }
2697 }
2698
2699 /*
2700 * The controller needs a reset of internal state machines
2701 * upon error conditions.
2702 */
2703 if (sdhci_needs_reset(host, mrq)) {
2704 /*
2705 * Do not finish until command and data lines are available for
2706 * reset. Note there can only be one other mrq, so it cannot
2707 * also be in mrqs_done, otherwise host->cmd and host->data_cmd
2708 * would both be null.
2709 */
2710 if (host->cmd || host->data_cmd) {
2711 spin_unlock_irqrestore(&host->lock, flags);
2712 return true;
2713 }
2714
2715 /* Some controllers need this kick or reset won't work here */
2716 if (host->quirks & SDHCI_QUIRK_CLOCK_BEFORE_RESET)
2717 /* This is to force an update */
2718 host->ops->set_clock(host, host->clock);
2719
2720 /* Spec says we should do both at the same time, but Ricoh
2721 controllers do not like that. */
2722 sdhci_do_reset(host, SDHCI_RESET_CMD);
2723 sdhci_do_reset(host, SDHCI_RESET_DATA);
2724
2725 host->pending_reset = false;
2726 }
2727
2728 host->mrqs_done[i] = NULL;
2729
2730 spin_unlock_irqrestore(&host->lock, flags);
2731
2732 mmc_request_done(host->mmc, mrq);
2733
2734 return false;
2735}
2736
2737static void sdhci_complete_work(struct work_struct *work)
2738{
2739 struct sdhci_host *host = container_of(work, struct sdhci_host,
2740 complete_work);
2741
2742 while (!sdhci_request_done(host))
2743 ;
2744}
2745
2746static void sdhci_timeout_timer(struct timer_list *t)
2747{
2748 struct sdhci_host *host;
2749 unsigned long flags;
2750
2751 host = from_timer(host, t, timer);
2752
2753 spin_lock_irqsave(&host->lock, flags);
2754
2755 if (host->cmd && !sdhci_data_line_cmd(host->cmd)) {
2756 pr_err("%s: Timeout waiting for hardware cmd interrupt.\n",
2757 mmc_hostname(host->mmc));
2758 sdhci_dumpregs(host);
2759
2760 host->cmd->error = -ETIMEDOUT;
2761 sdhci_finish_mrq(host, host->cmd->mrq);
2762 }
2763
2764 spin_unlock_irqrestore(&host->lock, flags);
2765}
2766
2767static void sdhci_timeout_data_timer(struct timer_list *t)
2768{
2769 struct sdhci_host *host;
2770 unsigned long flags;
2771
2772 host = from_timer(host, t, data_timer);
2773
2774 spin_lock_irqsave(&host->lock, flags);
2775
2776 if (host->data || host->data_cmd ||
2777 (host->cmd && sdhci_data_line_cmd(host->cmd))) {
2778 pr_err("%s: Timeout waiting for hardware interrupt.\n",
2779 mmc_hostname(host->mmc));
2780 sdhci_dumpregs(host);
2781
2782 if (host->data) {
2783 host->data->error = -ETIMEDOUT;
2784 sdhci_finish_data(host);
2785 queue_work(host->complete_wq, &host->complete_work);
2786 } else if (host->data_cmd) {
2787 host->data_cmd->error = -ETIMEDOUT;
2788 sdhci_finish_mrq(host, host->data_cmd->mrq);
2789 } else {
2790 host->cmd->error = -ETIMEDOUT;
2791 sdhci_finish_mrq(host, host->cmd->mrq);
2792 }
2793 }
2794
2795 spin_unlock_irqrestore(&host->lock, flags);
2796}
2797
2798/*****************************************************************************\
2799 * *
2800 * Interrupt handling *
2801 * *
2802\*****************************************************************************/
2803
2804static void sdhci_cmd_irq(struct sdhci_host *host, u32 intmask, u32 *intmask_p)
2805{
2806 /* Handle auto-CMD12 error */
2807 if (intmask & SDHCI_INT_AUTO_CMD_ERR && host->data_cmd) {
2808 struct mmc_request *mrq = host->data_cmd->mrq;
2809 u16 auto_cmd_status = sdhci_readw(host, SDHCI_AUTO_CMD_STATUS);
2810 int data_err_bit = (auto_cmd_status & SDHCI_AUTO_CMD_TIMEOUT) ?
2811 SDHCI_INT_DATA_TIMEOUT :
2812 SDHCI_INT_DATA_CRC;
2813
2814 /* Treat auto-CMD12 error the same as data error */
2815 if (!mrq->sbc && (host->flags & SDHCI_AUTO_CMD12)) {
2816 *intmask_p |= data_err_bit;
2817 return;
2818 }
2819 }
2820
2821 if (!host->cmd) {
2822 /*
2823 * SDHCI recovers from errors by resetting the cmd and data
2824 * circuits. Until that is done, there very well might be more
2825 * interrupts, so ignore them in that case.
2826 */
2827 if (host->pending_reset)
2828 return;
2829 pr_err("%s: Got command interrupt 0x%08x even though no command operation was in progress.\n",
2830 mmc_hostname(host->mmc), (unsigned)intmask);
2831 sdhci_dumpregs(host);
2832 return;
2833 }
2834
2835 if (intmask & (SDHCI_INT_TIMEOUT | SDHCI_INT_CRC |
2836 SDHCI_INT_END_BIT | SDHCI_INT_INDEX)) {
2837 if (intmask & SDHCI_INT_TIMEOUT)
2838 host->cmd->error = -ETIMEDOUT;
2839 else
2840 host->cmd->error = -EILSEQ;
2841
2842 /* Treat data command CRC error the same as data CRC error */
2843 if (host->cmd->data &&
2844 (intmask & (SDHCI_INT_CRC | SDHCI_INT_TIMEOUT)) ==
2845 SDHCI_INT_CRC) {
2846 host->cmd = NULL;
2847 *intmask_p |= SDHCI_INT_DATA_CRC;
2848 return;
2849 }
2850
2851 __sdhci_finish_mrq(host, host->cmd->mrq);
2852 return;
2853 }
2854
2855 /* Handle auto-CMD23 error */
2856 if (intmask & SDHCI_INT_AUTO_CMD_ERR) {
2857 struct mmc_request *mrq = host->cmd->mrq;
2858 u16 auto_cmd_status = sdhci_readw(host, SDHCI_AUTO_CMD_STATUS);
2859 int err = (auto_cmd_status & SDHCI_AUTO_CMD_TIMEOUT) ?
2860 -ETIMEDOUT :
2861 -EILSEQ;
2862
2863 if (mrq->sbc && (host->flags & SDHCI_AUTO_CMD23)) {
2864 mrq->sbc->error = err;
2865 __sdhci_finish_mrq(host, mrq);
2866 return;
2867 }
2868 }
2869
2870 if (intmask & SDHCI_INT_RESPONSE)
2871 sdhci_finish_command(host);
2872}
2873
2874static void sdhci_adma_show_error(struct sdhci_host *host)
2875{
2876 void *desc = host->adma_table;
2877 dma_addr_t dma = host->adma_addr;
2878
2879 sdhci_dumpregs(host);
2880
2881 while (true) {
2882 struct sdhci_adma2_64_desc *dma_desc = desc;
2883
2884 if (host->flags & SDHCI_USE_64_BIT_DMA)
2885 SDHCI_DUMP("%08llx: DMA 0x%08x%08x, LEN 0x%04x, Attr=0x%02x\n",
2886 (unsigned long long)dma,
2887 le32_to_cpu(dma_desc->addr_hi),
2888 le32_to_cpu(dma_desc->addr_lo),
2889 le16_to_cpu(dma_desc->len),
2890 le16_to_cpu(dma_desc->cmd));
2891 else
2892 SDHCI_DUMP("%08llx: DMA 0x%08x, LEN 0x%04x, Attr=0x%02x\n",
2893 (unsigned long long)dma,
2894 le32_to_cpu(dma_desc->addr_lo),
2895 le16_to_cpu(dma_desc->len),
2896 le16_to_cpu(dma_desc->cmd));
2897
2898 desc += host->desc_sz;
2899 dma += host->desc_sz;
2900
2901 if (dma_desc->cmd & cpu_to_le16(ADMA2_END))
2902 break;
2903 }
2904}
2905
2906static void sdhci_data_irq(struct sdhci_host *host, u32 intmask)
2907{
2908 u32 command;
2909
2910 /* CMD19 generates _only_ Buffer Read Ready interrupt */
2911 if (intmask & SDHCI_INT_DATA_AVAIL) {
2912 command = SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND));
2913 if (command == MMC_SEND_TUNING_BLOCK ||
2914 command == MMC_SEND_TUNING_BLOCK_HS200) {
2915 host->tuning_done = 1;
2916 wake_up(&host->buf_ready_int);
2917 return;
2918 }
2919 }
2920
2921 if (!host->data) {
2922 struct mmc_command *data_cmd = host->data_cmd;
2923
2924 /*
2925 * The "data complete" interrupt is also used to
2926 * indicate that a busy state has ended. See comment
2927 * above in sdhci_cmd_irq().
2928 */
2929 if (data_cmd && (data_cmd->flags & MMC_RSP_BUSY)) {
2930 if (intmask & SDHCI_INT_DATA_TIMEOUT) {
2931 host->data_cmd = NULL;
2932 data_cmd->error = -ETIMEDOUT;
2933 __sdhci_finish_mrq(host, data_cmd->mrq);
2934 return;
2935 }
2936 if (intmask & SDHCI_INT_DATA_END) {
2937 host->data_cmd = NULL;
2938 /*
2939 * Some cards handle busy-end interrupt
2940 * before the command completed, so make
2941 * sure we do things in the proper order.
2942 */
2943 if (host->cmd == data_cmd)
2944 return;
2945
2946 __sdhci_finish_mrq(host, data_cmd->mrq);
2947 return;
2948 }
2949 }
2950
2951 /*
2952 * SDHCI recovers from errors by resetting the cmd and data
2953 * circuits. Until that is done, there very well might be more
2954 * interrupts, so ignore them in that case.
2955 */
2956 if (host->pending_reset)
2957 return;
2958
2959 pr_err("%s: Got data interrupt 0x%08x even though no data operation was in progress.\n",
2960 mmc_hostname(host->mmc), (unsigned)intmask);
2961 sdhci_dumpregs(host);
2962
2963 return;
2964 }
2965
2966 if (intmask & SDHCI_INT_DATA_TIMEOUT)
2967 host->data->error = -ETIMEDOUT;
2968 else if (intmask & SDHCI_INT_DATA_END_BIT)
2969 host->data->error = -EILSEQ;
2970 else if ((intmask & SDHCI_INT_DATA_CRC) &&
2971 SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND))
2972 != MMC_BUS_TEST_R)
2973 host->data->error = -EILSEQ;
2974 else if (intmask & SDHCI_INT_ADMA_ERROR) {
2975 pr_err("%s: ADMA error: 0x%08x\n", mmc_hostname(host->mmc),
2976 intmask);
2977 sdhci_adma_show_error(host);
2978 host->data->error = -EIO;
2979 if (host->ops->adma_workaround)
2980 host->ops->adma_workaround(host, intmask);
2981 }
2982
2983 if (host->data->error)
2984 sdhci_finish_data(host);
2985 else {
2986 if (intmask & (SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL))
2987 sdhci_transfer_pio(host);
2988
2989 /*
2990 * We currently don't do anything fancy with DMA
2991 * boundaries, but as we can't disable the feature
2992 * we need to at least restart the transfer.
2993 *
2994 * According to the spec sdhci_readl(host, SDHCI_DMA_ADDRESS)
2995 * should return a valid address to continue from, but as
2996 * some controllers are faulty, don't trust them.
2997 */
2998 if (intmask & SDHCI_INT_DMA_END) {
2999 dma_addr_t dmastart, dmanow;
3000
3001 dmastart = sdhci_sdma_address(host);
3002 dmanow = dmastart + host->data->bytes_xfered;
3003 /*
3004 * Force update to the next DMA block boundary.
3005 */
3006 dmanow = (dmanow &
3007 ~((dma_addr_t)SDHCI_DEFAULT_BOUNDARY_SIZE - 1)) +
3008 SDHCI_DEFAULT_BOUNDARY_SIZE;
3009 host->data->bytes_xfered = dmanow - dmastart;
3010 DBG("DMA base %pad, transferred 0x%06x bytes, next %pad\n",
3011 &dmastart, host->data->bytes_xfered, &dmanow);
3012 sdhci_set_sdma_addr(host, dmanow);
3013 }
3014
3015 if (intmask & SDHCI_INT_DATA_END) {
3016 if (host->cmd == host->data_cmd) {
3017 /*
3018 * Data managed to finish before the
3019 * command completed. Make sure we do
3020 * things in the proper order.
3021 */
3022 host->data_early = 1;
3023 } else {
3024 sdhci_finish_data(host);
3025 }
3026 }
3027 }
3028}
3029
3030static inline bool sdhci_defer_done(struct sdhci_host *host,
3031 struct mmc_request *mrq)
3032{
3033 struct mmc_data *data = mrq->data;
3034
3035 return host->pending_reset ||
3036 ((host->flags & SDHCI_REQ_USE_DMA) && data &&
3037 data->host_cookie == COOKIE_MAPPED);
3038}
3039
3040static irqreturn_t sdhci_irq(int irq, void *dev_id)
3041{
3042 struct mmc_request *mrqs_done[SDHCI_MAX_MRQS] = {0};
3043 irqreturn_t result = IRQ_NONE;
3044 struct sdhci_host *host = dev_id;
3045 u32 intmask, mask, unexpected = 0;
3046 int max_loops = 16;
3047 int i;
3048
3049 spin_lock(&host->lock);
3050
3051 if (host->runtime_suspended) {
3052 spin_unlock(&host->lock);
3053 return IRQ_NONE;
3054 }
3055
3056 intmask = sdhci_readl(host, SDHCI_INT_STATUS);
3057 if (!intmask || intmask == 0xffffffff) {
3058 result = IRQ_NONE;
3059 goto out;
3060 }
3061
3062 do {
3063 DBG("IRQ status 0x%08x\n", intmask);
3064
3065 if (host->ops->irq) {
3066 intmask = host->ops->irq(host, intmask);
3067 if (!intmask)
3068 goto cont;
3069 }
3070
3071 /* Clear selected interrupts. */
3072 mask = intmask & (SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK |
3073 SDHCI_INT_BUS_POWER);
3074 sdhci_writel(host, mask, SDHCI_INT_STATUS);
3075
3076 if (intmask & (SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE)) {
3077 u32 present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
3078 SDHCI_CARD_PRESENT;
3079
3080 /*
3081 * There is a observation on i.mx esdhc. INSERT
3082 * bit will be immediately set again when it gets
3083 * cleared, if a card is inserted. We have to mask
3084 * the irq to prevent interrupt storm which will
3085 * freeze the system. And the REMOVE gets the
3086 * same situation.
3087 *
3088 * More testing are needed here to ensure it works
3089 * for other platforms though.
3090 */
3091 host->ier &= ~(SDHCI_INT_CARD_INSERT |
3092 SDHCI_INT_CARD_REMOVE);
3093 host->ier |= present ? SDHCI_INT_CARD_REMOVE :
3094 SDHCI_INT_CARD_INSERT;
3095 sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
3096 sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
3097
3098 sdhci_writel(host, intmask & (SDHCI_INT_CARD_INSERT |
3099 SDHCI_INT_CARD_REMOVE), SDHCI_INT_STATUS);
3100
3101 host->thread_isr |= intmask & (SDHCI_INT_CARD_INSERT |
3102 SDHCI_INT_CARD_REMOVE);
3103 result = IRQ_WAKE_THREAD;
3104 }
3105
3106 if (intmask & SDHCI_INT_CMD_MASK)
3107 sdhci_cmd_irq(host, intmask & SDHCI_INT_CMD_MASK, &intmask);
3108
3109 if (intmask & SDHCI_INT_DATA_MASK)
3110 sdhci_data_irq(host, intmask & SDHCI_INT_DATA_MASK);
3111
3112 if (intmask & SDHCI_INT_BUS_POWER)
3113 pr_err("%s: Card is consuming too much power!\n",
3114 mmc_hostname(host->mmc));
3115
3116 if (intmask & SDHCI_INT_RETUNE)
3117 mmc_retune_needed(host->mmc);
3118
3119 if ((intmask & SDHCI_INT_CARD_INT) &&
3120 (host->ier & SDHCI_INT_CARD_INT)) {
3121 sdhci_enable_sdio_irq_nolock(host, false);
3122 sdio_signal_irq(host->mmc);
3123 }
3124
3125 intmask &= ~(SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE |
3126 SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK |
3127 SDHCI_INT_ERROR | SDHCI_INT_BUS_POWER |
3128 SDHCI_INT_RETUNE | SDHCI_INT_CARD_INT);
3129
3130 if (intmask) {
3131 unexpected |= intmask;
3132 sdhci_writel(host, intmask, SDHCI_INT_STATUS);
3133 }
3134cont:
3135 if (result == IRQ_NONE)
3136 result = IRQ_HANDLED;
3137
3138 intmask = sdhci_readl(host, SDHCI_INT_STATUS);
3139 } while (intmask && --max_loops);
3140
3141 /* Determine if mrqs can be completed immediately */
3142 for (i = 0; i < SDHCI_MAX_MRQS; i++) {
3143 struct mmc_request *mrq = host->mrqs_done[i];
3144
3145 if (!mrq)
3146 continue;
3147
3148 if (sdhci_defer_done(host, mrq)) {
3149 result = IRQ_WAKE_THREAD;
3150 } else {
3151 mrqs_done[i] = mrq;
3152 host->mrqs_done[i] = NULL;
3153 }
3154 }
3155out:
3156 spin_unlock(&host->lock);
3157
3158 /* Process mrqs ready for immediate completion */
3159 for (i = 0; i < SDHCI_MAX_MRQS; i++) {
3160 if (mrqs_done[i])
3161 mmc_request_done(host->mmc, mrqs_done[i]);
3162 }
3163
3164 if (unexpected) {
3165 pr_err("%s: Unexpected interrupt 0x%08x.\n",
3166 mmc_hostname(host->mmc), unexpected);
3167 sdhci_dumpregs(host);
3168 }
3169
3170 return result;
3171}
3172
3173static irqreturn_t sdhci_thread_irq(int irq, void *dev_id)
3174{
3175 struct sdhci_host *host = dev_id;
3176 unsigned long flags;
3177 u32 isr;
3178
3179 while (!sdhci_request_done(host))
3180 ;
3181
3182 spin_lock_irqsave(&host->lock, flags);
3183 isr = host->thread_isr;
3184 host->thread_isr = 0;
3185 spin_unlock_irqrestore(&host->lock, flags);
3186
3187 if (isr & (SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE)) {
3188 struct mmc_host *mmc = host->mmc;
3189
3190 mmc->ops->card_event(mmc);
3191 mmc_detect_change(mmc, msecs_to_jiffies(200));
3192 }
3193
3194 return IRQ_HANDLED;
3195}
3196
3197/*****************************************************************************\
3198 * *
3199 * Suspend/resume *
3200 * *
3201\*****************************************************************************/
3202
3203#ifdef CONFIG_PM
3204
3205static bool sdhci_cd_irq_can_wakeup(struct sdhci_host *host)
3206{
3207 return mmc_card_is_removable(host->mmc) &&
3208 !(host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) &&
3209 !mmc_can_gpio_cd(host->mmc);
3210}
3211
3212/*
3213 * To enable wakeup events, the corresponding events have to be enabled in
3214 * the Interrupt Status Enable register too. See 'Table 1-6: Wakeup Signal
3215 * Table' in the SD Host Controller Standard Specification.
3216 * It is useless to restore SDHCI_INT_ENABLE state in
3217 * sdhci_disable_irq_wakeups() since it will be set by
3218 * sdhci_enable_card_detection() or sdhci_init().
3219 */
3220static bool sdhci_enable_irq_wakeups(struct sdhci_host *host)
3221{
3222 u8 mask = SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE |
3223 SDHCI_WAKE_ON_INT;
3224 u32 irq_val = 0;
3225 u8 wake_val = 0;
3226 u8 val;
3227
3228 if (sdhci_cd_irq_can_wakeup(host)) {
3229 wake_val |= SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE;
3230 irq_val |= SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE;
3231 }
3232
3233 if (mmc_card_wake_sdio_irq(host->mmc)) {
3234 wake_val |= SDHCI_WAKE_ON_INT;
3235 irq_val |= SDHCI_INT_CARD_INT;
3236 }
3237
3238 if (!irq_val)
3239 return false;
3240
3241 val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
3242 val &= ~mask;
3243 val |= wake_val;
3244 sdhci_writeb(host, val, SDHCI_WAKE_UP_CONTROL);
3245
3246 sdhci_writel(host, irq_val, SDHCI_INT_ENABLE);
3247
3248 host->irq_wake_enabled = !enable_irq_wake(host->irq);
3249
3250 return host->irq_wake_enabled;
3251}
3252
3253static void sdhci_disable_irq_wakeups(struct sdhci_host *host)
3254{
3255 u8 val;
3256 u8 mask = SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE
3257 | SDHCI_WAKE_ON_INT;
3258
3259 val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
3260 val &= ~mask;
3261 sdhci_writeb(host, val, SDHCI_WAKE_UP_CONTROL);
3262
3263 disable_irq_wake(host->irq);
3264
3265 host->irq_wake_enabled = false;
3266}
3267
3268int sdhci_suspend_host(struct sdhci_host *host)
3269{
3270 sdhci_disable_card_detection(host);
3271
3272 mmc_retune_timer_stop(host->mmc);
3273
3274 if (!device_may_wakeup(mmc_dev(host->mmc)) ||
3275 !sdhci_enable_irq_wakeups(host)) {
3276 host->ier = 0;
3277 sdhci_writel(host, 0, SDHCI_INT_ENABLE);
3278 sdhci_writel(host, 0, SDHCI_SIGNAL_ENABLE);
3279 free_irq(host->irq, host);
3280 }
3281
3282 return 0;
3283}
3284
3285EXPORT_SYMBOL_GPL(sdhci_suspend_host);
3286
3287int sdhci_resume_host(struct sdhci_host *host)
3288{
3289 struct mmc_host *mmc = host->mmc;
3290 int ret = 0;
3291
3292 if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
3293 if (host->ops->enable_dma)
3294 host->ops->enable_dma(host);
3295 }
3296
3297 if ((host->mmc->pm_flags & MMC_PM_KEEP_POWER) &&
3298 (host->quirks2 & SDHCI_QUIRK2_HOST_OFF_CARD_ON)) {
3299 /* Card keeps power but host controller does not */
3300 sdhci_init(host, 0);
3301 host->pwr = 0;
3302 host->clock = 0;
3303 mmc->ops->set_ios(mmc, &mmc->ios);
3304 } else {
3305 sdhci_init(host, (host->mmc->pm_flags & MMC_PM_KEEP_POWER));
3306 }
3307
3308 if (host->irq_wake_enabled) {
3309 sdhci_disable_irq_wakeups(host);
3310 } else {
3311 ret = request_threaded_irq(host->irq, sdhci_irq,
3312 sdhci_thread_irq, IRQF_SHARED,
3313 mmc_hostname(host->mmc), host);
3314 if (ret)
3315 return ret;
3316 }
3317
3318 sdhci_enable_card_detection(host);
3319
3320 return ret;
3321}
3322
3323EXPORT_SYMBOL_GPL(sdhci_resume_host);
3324
3325int sdhci_runtime_suspend_host(struct sdhci_host *host)
3326{
3327 unsigned long flags;
3328
3329 mmc_retune_timer_stop(host->mmc);
3330
3331 spin_lock_irqsave(&host->lock, flags);
3332 host->ier &= SDHCI_INT_CARD_INT;
3333 sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
3334 sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
3335 spin_unlock_irqrestore(&host->lock, flags);
3336
3337 synchronize_hardirq(host->irq);
3338
3339 spin_lock_irqsave(&host->lock, flags);
3340 host->runtime_suspended = true;
3341 spin_unlock_irqrestore(&host->lock, flags);
3342
3343 return 0;
3344}
3345EXPORT_SYMBOL_GPL(sdhci_runtime_suspend_host);
3346
3347int sdhci_runtime_resume_host(struct sdhci_host *host, int soft_reset)
3348{
3349 struct mmc_host *mmc = host->mmc;
3350 unsigned long flags;
3351 int host_flags = host->flags;
3352
3353 if (host_flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
3354 if (host->ops->enable_dma)
3355 host->ops->enable_dma(host);
3356 }
3357
3358 sdhci_init(host, soft_reset);
3359
3360 if (mmc->ios.power_mode != MMC_POWER_UNDEFINED &&
3361 mmc->ios.power_mode != MMC_POWER_OFF) {
3362 /* Force clock and power re-program */
3363 host->pwr = 0;
3364 host->clock = 0;
3365 mmc->ops->start_signal_voltage_switch(mmc, &mmc->ios);
3366 mmc->ops->set_ios(mmc, &mmc->ios);
3367
3368 if ((host_flags & SDHCI_PV_ENABLED) &&
3369 !(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN)) {
3370 spin_lock_irqsave(&host->lock, flags);
3371 sdhci_enable_preset_value(host, true);
3372 spin_unlock_irqrestore(&host->lock, flags);
3373 }
3374
3375 if ((mmc->caps2 & MMC_CAP2_HS400_ES) &&
3376 mmc->ops->hs400_enhanced_strobe)
3377 mmc->ops->hs400_enhanced_strobe(mmc, &mmc->ios);
3378 }
3379
3380 spin_lock_irqsave(&host->lock, flags);
3381
3382 host->runtime_suspended = false;
3383
3384 /* Enable SDIO IRQ */
3385 if (sdio_irq_claimed(mmc))
3386 sdhci_enable_sdio_irq_nolock(host, true);
3387
3388 /* Enable Card Detection */
3389 sdhci_enable_card_detection(host);
3390
3391 spin_unlock_irqrestore(&host->lock, flags);
3392
3393 return 0;
3394}
3395EXPORT_SYMBOL_GPL(sdhci_runtime_resume_host);
3396
3397#endif /* CONFIG_PM */
3398
3399/*****************************************************************************\
3400 * *
3401 * Command Queue Engine (CQE) helpers *
3402 * *
3403\*****************************************************************************/
3404
3405void sdhci_cqe_enable(struct mmc_host *mmc)
3406{
3407 struct sdhci_host *host = mmc_priv(mmc);
3408 unsigned long flags;
3409 u8 ctrl;
3410
3411 spin_lock_irqsave(&host->lock, flags);
3412
3413 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
3414 ctrl &= ~SDHCI_CTRL_DMA_MASK;
3415 /*
3416 * Host from V4.10 supports ADMA3 DMA type.
3417 * ADMA3 performs integrated descriptor which is more suitable
3418 * for cmd queuing to fetch both command and transfer descriptors.
3419 */
3420 if (host->v4_mode && (host->caps1 & SDHCI_CAN_DO_ADMA3))
3421 ctrl |= SDHCI_CTRL_ADMA3;
3422 else if (host->flags & SDHCI_USE_64_BIT_DMA)
3423 ctrl |= SDHCI_CTRL_ADMA64;
3424 else
3425 ctrl |= SDHCI_CTRL_ADMA32;
3426 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
3427
3428 sdhci_writew(host, SDHCI_MAKE_BLKSZ(host->sdma_boundary, 512),
3429 SDHCI_BLOCK_SIZE);
3430
3431 /* Set maximum timeout */
3432 sdhci_set_timeout(host, NULL);
3433
3434 host->ier = host->cqe_ier;
3435
3436 sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
3437 sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
3438
3439 host->cqe_on = true;
3440
3441 pr_debug("%s: sdhci: CQE on, IRQ mask %#x, IRQ status %#x\n",
3442 mmc_hostname(mmc), host->ier,
3443 sdhci_readl(host, SDHCI_INT_STATUS));
3444
3445 spin_unlock_irqrestore(&host->lock, flags);
3446}
3447EXPORT_SYMBOL_GPL(sdhci_cqe_enable);
3448
3449void sdhci_cqe_disable(struct mmc_host *mmc, bool recovery)
3450{
3451 struct sdhci_host *host = mmc_priv(mmc);
3452 unsigned long flags;
3453
3454 spin_lock_irqsave(&host->lock, flags);
3455
3456 sdhci_set_default_irqs(host);
3457
3458 host->cqe_on = false;
3459
3460 if (recovery) {
3461 sdhci_do_reset(host, SDHCI_RESET_CMD);
3462 sdhci_do_reset(host, SDHCI_RESET_DATA);
3463 }
3464
3465 pr_debug("%s: sdhci: CQE off, IRQ mask %#x, IRQ status %#x\n",
3466 mmc_hostname(mmc), host->ier,
3467 sdhci_readl(host, SDHCI_INT_STATUS));
3468
3469 spin_unlock_irqrestore(&host->lock, flags);
3470}
3471EXPORT_SYMBOL_GPL(sdhci_cqe_disable);
3472
3473bool sdhci_cqe_irq(struct sdhci_host *host, u32 intmask, int *cmd_error,
3474 int *data_error)
3475{
3476 u32 mask;
3477
3478 if (!host->cqe_on)
3479 return false;
3480
3481 if (intmask & (SDHCI_INT_INDEX | SDHCI_INT_END_BIT | SDHCI_INT_CRC))
3482 *cmd_error = -EILSEQ;
3483 else if (intmask & SDHCI_INT_TIMEOUT)
3484 *cmd_error = -ETIMEDOUT;
3485 else
3486 *cmd_error = 0;
3487
3488 if (intmask & (SDHCI_INT_DATA_END_BIT | SDHCI_INT_DATA_CRC))
3489 *data_error = -EILSEQ;
3490 else if (intmask & SDHCI_INT_DATA_TIMEOUT)
3491 *data_error = -ETIMEDOUT;
3492 else if (intmask & SDHCI_INT_ADMA_ERROR)
3493 *data_error = -EIO;
3494 else
3495 *data_error = 0;
3496
3497 /* Clear selected interrupts. */
3498 mask = intmask & host->cqe_ier;
3499 sdhci_writel(host, mask, SDHCI_INT_STATUS);
3500
3501 if (intmask & SDHCI_INT_BUS_POWER)
3502 pr_err("%s: Card is consuming too much power!\n",
3503 mmc_hostname(host->mmc));
3504
3505 intmask &= ~(host->cqe_ier | SDHCI_INT_ERROR);
3506 if (intmask) {
3507 sdhci_writel(host, intmask, SDHCI_INT_STATUS);
3508 pr_err("%s: CQE: Unexpected interrupt 0x%08x.\n",
3509 mmc_hostname(host->mmc), intmask);
3510 sdhci_dumpregs(host);
3511 }
3512
3513 return true;
3514}
3515EXPORT_SYMBOL_GPL(sdhci_cqe_irq);
3516
3517/*****************************************************************************\
3518 * *
3519 * Device allocation/registration *
3520 * *
3521\*****************************************************************************/
3522
3523struct sdhci_host *sdhci_alloc_host(struct device *dev,
3524 size_t priv_size)
3525{
3526 struct mmc_host *mmc;
3527 struct sdhci_host *host;
3528
3529 WARN_ON(dev == NULL);
3530
3531 mmc = mmc_alloc_host(sizeof(struct sdhci_host) + priv_size, dev);
3532 if (!mmc)
3533 return ERR_PTR(-ENOMEM);
3534
3535 host = mmc_priv(mmc);
3536 host->mmc = mmc;
3537 host->mmc_host_ops = sdhci_ops;
3538 mmc->ops = &host->mmc_host_ops;
3539
3540 host->flags = SDHCI_SIGNALING_330;
3541
3542 host->cqe_ier = SDHCI_CQE_INT_MASK;
3543 host->cqe_err_ier = SDHCI_CQE_INT_ERR_MASK;
3544
3545 host->tuning_delay = -1;
3546 host->tuning_loop_count = MAX_TUNING_LOOP;
3547
3548 host->sdma_boundary = SDHCI_DEFAULT_BOUNDARY_ARG;
3549
3550 /*
3551 * The DMA table descriptor count is calculated as the maximum
3552 * number of segments times 2, to allow for an alignment
3553 * descriptor for each segment, plus 1 for a nop end descriptor.
3554 */
3555 host->adma_table_cnt = SDHCI_MAX_SEGS * 2 + 1;
3556
3557 return host;
3558}
3559
3560EXPORT_SYMBOL_GPL(sdhci_alloc_host);
3561
3562static int sdhci_set_dma_mask(struct sdhci_host *host)
3563{
3564 struct mmc_host *mmc = host->mmc;
3565 struct device *dev = mmc_dev(mmc);
3566 int ret = -EINVAL;
3567
3568 if (host->quirks2 & SDHCI_QUIRK2_BROKEN_64_BIT_DMA)
3569 host->flags &= ~SDHCI_USE_64_BIT_DMA;
3570
3571 /* Try 64-bit mask if hardware is capable of it */
3572 if (host->flags & SDHCI_USE_64_BIT_DMA) {
3573 ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(64));
3574 if (ret) {
3575 pr_warn("%s: Failed to set 64-bit DMA mask.\n",
3576 mmc_hostname(mmc));
3577 host->flags &= ~SDHCI_USE_64_BIT_DMA;
3578 }
3579 }
3580
3581 /* 32-bit mask as default & fallback */
3582 if (ret) {
3583 ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
3584 if (ret)
3585 pr_warn("%s: Failed to set 32-bit DMA mask.\n",
3586 mmc_hostname(mmc));
3587 }
3588
3589 return ret;
3590}
3591
3592void __sdhci_read_caps(struct sdhci_host *host, const u16 *ver,
3593 const u32 *caps, const u32 *caps1)
3594{
3595 u16 v;
3596 u64 dt_caps_mask = 0;
3597 u64 dt_caps = 0;
3598
3599 if (host->read_caps)
3600 return;
3601
3602 host->read_caps = true;
3603
3604 if (debug_quirks)
3605 host->quirks = debug_quirks;
3606
3607 if (debug_quirks2)
3608 host->quirks2 = debug_quirks2;
3609
3610 sdhci_do_reset(host, SDHCI_RESET_ALL);
3611
3612 if (host->v4_mode)
3613 sdhci_do_enable_v4_mode(host);
3614
3615 of_property_read_u64(mmc_dev(host->mmc)->of_node,
3616 "sdhci-caps-mask", &dt_caps_mask);
3617 of_property_read_u64(mmc_dev(host->mmc)->of_node,
3618 "sdhci-caps", &dt_caps);
3619
3620 v = ver ? *ver : sdhci_readw(host, SDHCI_HOST_VERSION);
3621 host->version = (v & SDHCI_SPEC_VER_MASK) >> SDHCI_SPEC_VER_SHIFT;
3622
3623 if (host->quirks & SDHCI_QUIRK_MISSING_CAPS)
3624 return;
3625
3626 if (caps) {
3627 host->caps = *caps;
3628 } else {
3629 host->caps = sdhci_readl(host, SDHCI_CAPABILITIES);
3630 host->caps &= ~lower_32_bits(dt_caps_mask);
3631 host->caps |= lower_32_bits(dt_caps);
3632 }
3633
3634 if (host->version < SDHCI_SPEC_300)
3635 return;
3636
3637 if (caps1) {
3638 host->caps1 = *caps1;
3639 } else {
3640 host->caps1 = sdhci_readl(host, SDHCI_CAPABILITIES_1);
3641 host->caps1 &= ~upper_32_bits(dt_caps_mask);
3642 host->caps1 |= upper_32_bits(dt_caps);
3643 }
3644}
3645EXPORT_SYMBOL_GPL(__sdhci_read_caps);
3646
3647static void sdhci_allocate_bounce_buffer(struct sdhci_host *host)
3648{
3649 struct mmc_host *mmc = host->mmc;
3650 unsigned int max_blocks;
3651 unsigned int bounce_size;
3652 int ret;
3653
3654 /*
3655 * Cap the bounce buffer at 64KB. Using a bigger bounce buffer
3656 * has diminishing returns, this is probably because SD/MMC
3657 * cards are usually optimized to handle this size of requests.
3658 */
3659 bounce_size = SZ_64K;
3660 /*
3661 * Adjust downwards to maximum request size if this is less
3662 * than our segment size, else hammer down the maximum
3663 * request size to the maximum buffer size.
3664 */
3665 if (mmc->max_req_size < bounce_size)
3666 bounce_size = mmc->max_req_size;
3667 max_blocks = bounce_size / 512;
3668
3669 /*
3670 * When we just support one segment, we can get significant
3671 * speedups by the help of a bounce buffer to group scattered
3672 * reads/writes together.
3673 */
3674 host->bounce_buffer = devm_kmalloc(mmc->parent,
3675 bounce_size,
3676 GFP_KERNEL);
3677 if (!host->bounce_buffer) {
3678 pr_err("%s: failed to allocate %u bytes for bounce buffer, falling back to single segments\n",
3679 mmc_hostname(mmc),
3680 bounce_size);
3681 /*
3682 * Exiting with zero here makes sure we proceed with
3683 * mmc->max_segs == 1.
3684 */
3685 return;
3686 }
3687
3688 host->bounce_addr = dma_map_single(mmc->parent,
3689 host->bounce_buffer,
3690 bounce_size,
3691 DMA_BIDIRECTIONAL);
3692 ret = dma_mapping_error(mmc->parent, host->bounce_addr);
3693 if (ret)
3694 /* Again fall back to max_segs == 1 */
3695 return;
3696 host->bounce_buffer_size = bounce_size;
3697
3698 /* Lie about this since we're bouncing */
3699 mmc->max_segs = max_blocks;
3700 mmc->max_seg_size = bounce_size;
3701 mmc->max_req_size = bounce_size;
3702
3703 pr_info("%s bounce up to %u segments into one, max segment size %u bytes\n",
3704 mmc_hostname(mmc), max_blocks, bounce_size);
3705}
3706
3707static inline bool sdhci_can_64bit_dma(struct sdhci_host *host)
3708{
3709 /*
3710 * According to SD Host Controller spec v4.10, bit[27] added from
3711 * version 4.10 in Capabilities Register is used as 64-bit System
3712 * Address support for V4 mode.
3713 */
3714 if (host->version >= SDHCI_SPEC_410 && host->v4_mode)
3715 return host->caps & SDHCI_CAN_64BIT_V4;
3716
3717 return host->caps & SDHCI_CAN_64BIT;
3718}
3719
3720int sdhci_setup_host(struct sdhci_host *host)
3721{
3722 struct mmc_host *mmc;
3723 u32 max_current_caps;
3724 unsigned int ocr_avail;
3725 unsigned int override_timeout_clk;
3726 u32 max_clk;
3727 int ret;
3728
3729 WARN_ON(host == NULL);
3730 if (host == NULL)
3731 return -EINVAL;
3732
3733 mmc = host->mmc;
3734
3735 /*
3736 * If there are external regulators, get them. Note this must be done
3737 * early before resetting the host and reading the capabilities so that
3738 * the host can take the appropriate action if regulators are not
3739 * available.
3740 */
3741 ret = mmc_regulator_get_supply(mmc);
3742 if (ret)
3743 return ret;
3744
3745 DBG("Version: 0x%08x | Present: 0x%08x\n",
3746 sdhci_readw(host, SDHCI_HOST_VERSION),
3747 sdhci_readl(host, SDHCI_PRESENT_STATE));
3748 DBG("Caps: 0x%08x | Caps_1: 0x%08x\n",
3749 sdhci_readl(host, SDHCI_CAPABILITIES),
3750 sdhci_readl(host, SDHCI_CAPABILITIES_1));
3751
3752 sdhci_read_caps(host);
3753
3754 override_timeout_clk = host->timeout_clk;
3755
3756 if (host->version > SDHCI_SPEC_420) {
3757 pr_err("%s: Unknown controller version (%d). You may experience problems.\n",
3758 mmc_hostname(mmc), host->version);
3759 }
3760
3761 if (host->quirks & SDHCI_QUIRK_FORCE_DMA)
3762 host->flags |= SDHCI_USE_SDMA;
3763 else if (!(host->caps & SDHCI_CAN_DO_SDMA))
3764 DBG("Controller doesn't have SDMA capability\n");
3765 else
3766 host->flags |= SDHCI_USE_SDMA;
3767
3768 if ((host->quirks & SDHCI_QUIRK_BROKEN_DMA) &&
3769 (host->flags & SDHCI_USE_SDMA)) {
3770 DBG("Disabling DMA as it is marked broken\n");
3771 host->flags &= ~SDHCI_USE_SDMA;
3772 }
3773
3774 if ((host->version >= SDHCI_SPEC_200) &&
3775 (host->caps & SDHCI_CAN_DO_ADMA2))
3776 host->flags |= SDHCI_USE_ADMA;
3777
3778 if ((host->quirks & SDHCI_QUIRK_BROKEN_ADMA) &&
3779 (host->flags & SDHCI_USE_ADMA)) {
3780 DBG("Disabling ADMA as it is marked broken\n");
3781 host->flags &= ~SDHCI_USE_ADMA;
3782 }
3783
3784 if (sdhci_can_64bit_dma(host))
3785 host->flags |= SDHCI_USE_64_BIT_DMA;
3786
3787 if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
3788 if (host->ops->set_dma_mask)
3789 ret = host->ops->set_dma_mask(host);
3790 else
3791 ret = sdhci_set_dma_mask(host);
3792
3793 if (!ret && host->ops->enable_dma)
3794 ret = host->ops->enable_dma(host);
3795
3796 if (ret) {
3797 pr_warn("%s: No suitable DMA available - falling back to PIO\n",
3798 mmc_hostname(mmc));
3799 host->flags &= ~(SDHCI_USE_SDMA | SDHCI_USE_ADMA);
3800
3801 ret = 0;
3802 }
3803 }
3804
3805 /* SDMA does not support 64-bit DMA if v4 mode not set */
3806 if ((host->flags & SDHCI_USE_64_BIT_DMA) && !host->v4_mode)
3807 host->flags &= ~SDHCI_USE_SDMA;
3808
3809 if (host->flags & SDHCI_USE_ADMA) {
3810 dma_addr_t dma;
3811 void *buf;
3812
3813 if (host->flags & SDHCI_USE_64_BIT_DMA) {
3814 host->adma_table_sz = host->adma_table_cnt *
3815 SDHCI_ADMA2_64_DESC_SZ(host);
3816 host->desc_sz = SDHCI_ADMA2_64_DESC_SZ(host);
3817 } else {
3818 host->adma_table_sz = host->adma_table_cnt *
3819 SDHCI_ADMA2_32_DESC_SZ;
3820 host->desc_sz = SDHCI_ADMA2_32_DESC_SZ;
3821 }
3822
3823 host->align_buffer_sz = SDHCI_MAX_SEGS * SDHCI_ADMA2_ALIGN;
3824 /*
3825 * Use zalloc to zero the reserved high 32-bits of 128-bit
3826 * descriptors so that they never need to be written.
3827 */
3828 buf = dma_alloc_coherent(mmc_dev(mmc),
3829 host->align_buffer_sz + host->adma_table_sz,
3830 &dma, GFP_KERNEL);
3831 if (!buf) {
3832 pr_warn("%s: Unable to allocate ADMA buffers - falling back to standard DMA\n",
3833 mmc_hostname(mmc));
3834 host->flags &= ~SDHCI_USE_ADMA;
3835 } else if ((dma + host->align_buffer_sz) &
3836 (SDHCI_ADMA2_DESC_ALIGN - 1)) {
3837 pr_warn("%s: unable to allocate aligned ADMA descriptor\n",
3838 mmc_hostname(mmc));
3839 host->flags &= ~SDHCI_USE_ADMA;
3840 dma_free_coherent(mmc_dev(mmc), host->align_buffer_sz +
3841 host->adma_table_sz, buf, dma);
3842 } else {
3843 host->align_buffer = buf;
3844 host->align_addr = dma;
3845
3846 host->adma_table = buf + host->align_buffer_sz;
3847 host->adma_addr = dma + host->align_buffer_sz;
3848 }
3849 }
3850
3851 /*
3852 * If we use DMA, then it's up to the caller to set the DMA
3853 * mask, but PIO does not need the hw shim so we set a new
3854 * mask here in that case.
3855 */
3856 if (!(host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA))) {
3857 host->dma_mask = DMA_BIT_MASK(64);
3858 mmc_dev(mmc)->dma_mask = &host->dma_mask;
3859 }
3860
3861 if (host->version >= SDHCI_SPEC_300)
3862 host->max_clk = (host->caps & SDHCI_CLOCK_V3_BASE_MASK)
3863 >> SDHCI_CLOCK_BASE_SHIFT;
3864 else
3865 host->max_clk = (host->caps & SDHCI_CLOCK_BASE_MASK)
3866 >> SDHCI_CLOCK_BASE_SHIFT;
3867
3868 host->max_clk *= 1000000;
3869 if (host->max_clk == 0 || host->quirks &
3870 SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN) {
3871 if (!host->ops->get_max_clock) {
3872 pr_err("%s: Hardware doesn't specify base clock frequency.\n",
3873 mmc_hostname(mmc));
3874 ret = -ENODEV;
3875 goto undma;
3876 }
3877 host->max_clk = host->ops->get_max_clock(host);
3878 }
3879
3880 /*
3881 * In case of Host Controller v3.00, find out whether clock
3882 * multiplier is supported.
3883 */
3884 host->clk_mul = (host->caps1 & SDHCI_CLOCK_MUL_MASK) >>
3885 SDHCI_CLOCK_MUL_SHIFT;
3886
3887 /*
3888 * In case the value in Clock Multiplier is 0, then programmable
3889 * clock mode is not supported, otherwise the actual clock
3890 * multiplier is one more than the value of Clock Multiplier
3891 * in the Capabilities Register.
3892 */
3893 if (host->clk_mul)
3894 host->clk_mul += 1;
3895
3896 /*
3897 * Set host parameters.
3898 */
3899 max_clk = host->max_clk;
3900
3901 if (host->ops->get_min_clock)
3902 mmc->f_min = host->ops->get_min_clock(host);
3903 else if (host->version >= SDHCI_SPEC_300) {
3904 if (host->clk_mul) {
3905 mmc->f_min = (host->max_clk * host->clk_mul) / 1024;
3906 max_clk = host->max_clk * host->clk_mul;
3907 } else
3908 mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_300;
3909 } else
3910 mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_200;
3911
3912 if (!mmc->f_max || mmc->f_max > max_clk)
3913 mmc->f_max = max_clk;
3914
3915 if (!(host->quirks & SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK)) {
3916 host->timeout_clk = (host->caps & SDHCI_TIMEOUT_CLK_MASK) >>
3917 SDHCI_TIMEOUT_CLK_SHIFT;
3918
3919 if (host->caps & SDHCI_TIMEOUT_CLK_UNIT)
3920 host->timeout_clk *= 1000;
3921
3922 if (host->timeout_clk == 0) {
3923 if (!host->ops->get_timeout_clock) {
3924 pr_err("%s: Hardware doesn't specify timeout clock frequency.\n",
3925 mmc_hostname(mmc));
3926 ret = -ENODEV;
3927 goto undma;
3928 }
3929
3930 host->timeout_clk =
3931 DIV_ROUND_UP(host->ops->get_timeout_clock(host),
3932 1000);
3933 }
3934
3935 if (override_timeout_clk)
3936 host->timeout_clk = override_timeout_clk;
3937
3938 mmc->max_busy_timeout = host->ops->get_max_timeout_count ?
3939 host->ops->get_max_timeout_count(host) : 1 << 27;
3940 mmc->max_busy_timeout /= host->timeout_clk;
3941 }
3942
3943 if (host->quirks2 & SDHCI_QUIRK2_DISABLE_HW_TIMEOUT &&
3944 !host->ops->get_max_timeout_count)
3945 mmc->max_busy_timeout = 0;
3946
3947 mmc->caps |= MMC_CAP_SDIO_IRQ | MMC_CAP_ERASE | MMC_CAP_CMD23;
3948 mmc->caps2 |= MMC_CAP2_SDIO_IRQ_NOTHREAD;
3949
3950 if (host->quirks & SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12)
3951 host->flags |= SDHCI_AUTO_CMD12;
3952
3953 /*
3954 * For v3 mode, Auto-CMD23 stuff only works in ADMA or PIO.
3955 * For v4 mode, SDMA may use Auto-CMD23 as well.
3956 */
3957 if ((host->version >= SDHCI_SPEC_300) &&
3958 ((host->flags & SDHCI_USE_ADMA) ||
3959 !(host->flags & SDHCI_USE_SDMA) || host->v4_mode) &&
3960 !(host->quirks2 & SDHCI_QUIRK2_ACMD23_BROKEN)) {
3961 host->flags |= SDHCI_AUTO_CMD23;
3962 DBG("Auto-CMD23 available\n");
3963 } else {
3964 DBG("Auto-CMD23 unavailable\n");
3965 }
3966
3967 /*
3968 * A controller may support 8-bit width, but the board itself
3969 * might not have the pins brought out. Boards that support
3970 * 8-bit width must set "mmc->caps |= MMC_CAP_8_BIT_DATA;" in
3971 * their platform code before calling sdhci_add_host(), and we
3972 * won't assume 8-bit width for hosts without that CAP.
3973 */
3974 if (!(host->quirks & SDHCI_QUIRK_FORCE_1_BIT_DATA))
3975 mmc->caps |= MMC_CAP_4_BIT_DATA;
3976
3977 if (host->quirks2 & SDHCI_QUIRK2_HOST_NO_CMD23)
3978 mmc->caps &= ~MMC_CAP_CMD23;
3979
3980 if (host->caps & SDHCI_CAN_DO_HISPD)
3981 mmc->caps |= MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED;
3982
3983 if ((host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) &&
3984 mmc_card_is_removable(mmc) &&
3985 mmc_gpio_get_cd(host->mmc) < 0)
3986 mmc->caps |= MMC_CAP_NEEDS_POLL;
3987
3988 if (!IS_ERR(mmc->supply.vqmmc)) {
3989 ret = regulator_enable(mmc->supply.vqmmc);
3990
3991 /* If vqmmc provides no 1.8V signalling, then there's no UHS */
3992 if (!regulator_is_supported_voltage(mmc->supply.vqmmc, 1700000,
3993 1950000))
3994 host->caps1 &= ~(SDHCI_SUPPORT_SDR104 |
3995 SDHCI_SUPPORT_SDR50 |
3996 SDHCI_SUPPORT_DDR50);
3997
3998 /* In eMMC case vqmmc might be a fixed 1.8V regulator */
3999 if (!regulator_is_supported_voltage(mmc->supply.vqmmc, 2700000,
4000 3600000))
4001 host->flags &= ~SDHCI_SIGNALING_330;
4002
4003 if (ret) {
4004 pr_warn("%s: Failed to enable vqmmc regulator: %d\n",
4005 mmc_hostname(mmc), ret);
4006 mmc->supply.vqmmc = ERR_PTR(-EINVAL);
4007 }
4008 }
4009
4010 if (host->quirks2 & SDHCI_QUIRK2_NO_1_8_V) {
4011 host->caps1 &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 |
4012 SDHCI_SUPPORT_DDR50);
4013 /*
4014 * The SDHCI controller in a SoC might support HS200/HS400
4015 * (indicated using mmc-hs200-1_8v/mmc-hs400-1_8v dt property),
4016 * but if the board is modeled such that the IO lines are not
4017 * connected to 1.8v then HS200/HS400 cannot be supported.
4018 * Disable HS200/HS400 if the board does not have 1.8v connected
4019 * to the IO lines. (Applicable for other modes in 1.8v)
4020 */
4021 mmc->caps2 &= ~(MMC_CAP2_HSX00_1_8V | MMC_CAP2_HS400_ES);
4022 mmc->caps &= ~(MMC_CAP_1_8V_DDR | MMC_CAP_UHS);
4023 }
4024
4025 /* Any UHS-I mode in caps implies SDR12 and SDR25 support. */
4026 if (host->caps1 & (SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 |
4027 SDHCI_SUPPORT_DDR50))
4028 mmc->caps |= MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25;
4029
4030 /* SDR104 supports also implies SDR50 support */
4031 if (host->caps1 & SDHCI_SUPPORT_SDR104) {
4032 mmc->caps |= MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_SDR50;
4033 /* SD3.0: SDR104 is supported so (for eMMC) the caps2
4034 * field can be promoted to support HS200.
4035 */
4036 if (!(host->quirks2 & SDHCI_QUIRK2_BROKEN_HS200))
4037 mmc->caps2 |= MMC_CAP2_HS200;
4038 } else if (host->caps1 & SDHCI_SUPPORT_SDR50) {
4039 mmc->caps |= MMC_CAP_UHS_SDR50;
4040 }
4041
4042 if (host->quirks2 & SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 &&
4043 (host->caps1 & SDHCI_SUPPORT_HS400))
4044 mmc->caps2 |= MMC_CAP2_HS400;
4045
4046 if ((mmc->caps2 & MMC_CAP2_HSX00_1_2V) &&
4047 (IS_ERR(mmc->supply.vqmmc) ||
4048 !regulator_is_supported_voltage(mmc->supply.vqmmc, 1100000,
4049 1300000)))
4050 mmc->caps2 &= ~MMC_CAP2_HSX00_1_2V;
4051
4052 if ((host->caps1 & SDHCI_SUPPORT_DDR50) &&
4053 !(host->quirks2 & SDHCI_QUIRK2_BROKEN_DDR50))
4054 mmc->caps |= MMC_CAP_UHS_DDR50;
4055
4056 /* Does the host need tuning for SDR50? */
4057 if (host->caps1 & SDHCI_USE_SDR50_TUNING)
4058 host->flags |= SDHCI_SDR50_NEEDS_TUNING;
4059
4060 /* Driver Type(s) (A, C, D) supported by the host */
4061 if (host->caps1 & SDHCI_DRIVER_TYPE_A)
4062 mmc->caps |= MMC_CAP_DRIVER_TYPE_A;
4063 if (host->caps1 & SDHCI_DRIVER_TYPE_C)
4064 mmc->caps |= MMC_CAP_DRIVER_TYPE_C;
4065 if (host->caps1 & SDHCI_DRIVER_TYPE_D)
4066 mmc->caps |= MMC_CAP_DRIVER_TYPE_D;
4067
4068 /* Initial value for re-tuning timer count */
4069 host->tuning_count = (host->caps1 & SDHCI_RETUNING_TIMER_COUNT_MASK) >>
4070 SDHCI_RETUNING_TIMER_COUNT_SHIFT;
4071
4072 /*
4073 * In case Re-tuning Timer is not disabled, the actual value of
4074 * re-tuning timer will be 2 ^ (n - 1).
4075 */
4076 if (host->tuning_count)
4077 host->tuning_count = 1 << (host->tuning_count - 1);
4078
4079 /* Re-tuning mode supported by the Host Controller */
4080 host->tuning_mode = (host->caps1 & SDHCI_RETUNING_MODE_MASK) >>
4081 SDHCI_RETUNING_MODE_SHIFT;
4082
4083 ocr_avail = 0;
4084
4085 /*
4086 * According to SD Host Controller spec v3.00, if the Host System
4087 * can afford more than 150mA, Host Driver should set XPC to 1. Also
4088 * the value is meaningful only if Voltage Support in the Capabilities
4089 * register is set. The actual current value is 4 times the register
4090 * value.
4091 */
4092 max_current_caps = sdhci_readl(host, SDHCI_MAX_CURRENT);
4093 if (!max_current_caps && !IS_ERR(mmc->supply.vmmc)) {
4094 int curr = regulator_get_current_limit(mmc->supply.vmmc);
4095 if (curr > 0) {
4096
4097 /* convert to SDHCI_MAX_CURRENT format */
4098 curr = curr/1000; /* convert to mA */
4099 curr = curr/SDHCI_MAX_CURRENT_MULTIPLIER;
4100
4101 curr = min_t(u32, curr, SDHCI_MAX_CURRENT_LIMIT);
4102 max_current_caps =
4103 (curr << SDHCI_MAX_CURRENT_330_SHIFT) |
4104 (curr << SDHCI_MAX_CURRENT_300_SHIFT) |
4105 (curr << SDHCI_MAX_CURRENT_180_SHIFT);
4106 }
4107 }
4108
4109 if (host->caps & SDHCI_CAN_VDD_330) {
4110 ocr_avail |= MMC_VDD_32_33 | MMC_VDD_33_34;
4111
4112 mmc->max_current_330 = ((max_current_caps &
4113 SDHCI_MAX_CURRENT_330_MASK) >>
4114 SDHCI_MAX_CURRENT_330_SHIFT) *
4115 SDHCI_MAX_CURRENT_MULTIPLIER;
4116 }
4117 if (host->caps & SDHCI_CAN_VDD_300) {
4118 ocr_avail |= MMC_VDD_29_30 | MMC_VDD_30_31;
4119
4120 mmc->max_current_300 = ((max_current_caps &
4121 SDHCI_MAX_CURRENT_300_MASK) >>
4122 SDHCI_MAX_CURRENT_300_SHIFT) *
4123 SDHCI_MAX_CURRENT_MULTIPLIER;
4124 }
4125 if (host->caps & SDHCI_CAN_VDD_180) {
4126 ocr_avail |= MMC_VDD_165_195;
4127
4128 mmc->max_current_180 = ((max_current_caps &
4129 SDHCI_MAX_CURRENT_180_MASK) >>
4130 SDHCI_MAX_CURRENT_180_SHIFT) *
4131 SDHCI_MAX_CURRENT_MULTIPLIER;
4132 }
4133
4134 /* If OCR set by host, use it instead. */
4135 if (host->ocr_mask)
4136 ocr_avail = host->ocr_mask;
4137
4138 /* If OCR set by external regulators, give it highest prio. */
4139 if (mmc->ocr_avail)
4140 ocr_avail = mmc->ocr_avail;
4141
4142 mmc->ocr_avail = ocr_avail;
4143 mmc->ocr_avail_sdio = ocr_avail;
4144 if (host->ocr_avail_sdio)
4145 mmc->ocr_avail_sdio &= host->ocr_avail_sdio;
4146 mmc->ocr_avail_sd = ocr_avail;
4147 if (host->ocr_avail_sd)
4148 mmc->ocr_avail_sd &= host->ocr_avail_sd;
4149 else /* normal SD controllers don't support 1.8V */
4150 mmc->ocr_avail_sd &= ~MMC_VDD_165_195;
4151 mmc->ocr_avail_mmc = ocr_avail;
4152 if (host->ocr_avail_mmc)
4153 mmc->ocr_avail_mmc &= host->ocr_avail_mmc;
4154
4155 if (mmc->ocr_avail == 0) {
4156 pr_err("%s: Hardware doesn't report any support voltages.\n",
4157 mmc_hostname(mmc));
4158 ret = -ENODEV;
4159 goto unreg;
4160 }
4161
4162 if ((mmc->caps & (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
4163 MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 |
4164 MMC_CAP_UHS_DDR50 | MMC_CAP_1_8V_DDR)) ||
4165 (mmc->caps2 & (MMC_CAP2_HS200_1_8V_SDR | MMC_CAP2_HS400_1_8V)))
4166 host->flags |= SDHCI_SIGNALING_180;
4167
4168 if (mmc->caps2 & MMC_CAP2_HSX00_1_2V)
4169 host->flags |= SDHCI_SIGNALING_120;
4170
4171 spin_lock_init(&host->lock);
4172
4173 /*
4174 * Maximum number of sectors in one transfer. Limited by SDMA boundary
4175 * size (512KiB). Note some tuning modes impose a 4MiB limit, but this
4176 * is less anyway.
4177 */
4178 mmc->max_req_size = 524288;
4179
4180 /*
4181 * Maximum number of segments. Depends on if the hardware
4182 * can do scatter/gather or not.
4183 */
4184 if (host->flags & SDHCI_USE_ADMA) {
4185 mmc->max_segs = SDHCI_MAX_SEGS;
4186 } else if (host->flags & SDHCI_USE_SDMA) {
4187 mmc->max_segs = 1;
4188 if (swiotlb_max_segment()) {
4189 unsigned int max_req_size = (1 << IO_TLB_SHIFT) *
4190 IO_TLB_SEGSIZE;
4191 mmc->max_req_size = min(mmc->max_req_size,
4192 max_req_size);
4193 }
4194 } else { /* PIO */
4195 mmc->max_segs = SDHCI_MAX_SEGS;
4196 }
4197
4198 /*
4199 * Maximum segment size. Could be one segment with the maximum number
4200 * of bytes. When doing hardware scatter/gather, each entry cannot
4201 * be larger than 64 KiB though.
4202 */
4203 if (host->flags & SDHCI_USE_ADMA) {
4204 if (host->quirks & SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC)
4205 mmc->max_seg_size = 65535;
4206 else
4207 mmc->max_seg_size = 65536;
4208 } else {
4209 mmc->max_seg_size = mmc->max_req_size;
4210 }
4211
4212 /*
4213 * Maximum block size. This varies from controller to controller and
4214 * is specified in the capabilities register.
4215 */
4216 if (host->quirks & SDHCI_QUIRK_FORCE_BLK_SZ_2048) {
4217 mmc->max_blk_size = 2;
4218 } else {
4219 mmc->max_blk_size = (host->caps & SDHCI_MAX_BLOCK_MASK) >>
4220 SDHCI_MAX_BLOCK_SHIFT;
4221 if (mmc->max_blk_size >= 3) {
4222 pr_warn("%s: Invalid maximum block size, assuming 512 bytes\n",
4223 mmc_hostname(mmc));
4224 mmc->max_blk_size = 0;
4225 }
4226 }
4227
4228 mmc->max_blk_size = 512 << mmc->max_blk_size;
4229
4230 /*
4231 * Maximum block count.
4232 */
4233 mmc->max_blk_count = (host->quirks & SDHCI_QUIRK_NO_MULTIBLOCK) ? 1 : 65535;
4234
4235 if (mmc->max_segs == 1)
4236 /* This may alter mmc->*_blk_* parameters */
4237 sdhci_allocate_bounce_buffer(host);
4238
4239 return 0;
4240
4241unreg:
4242 if (!IS_ERR(mmc->supply.vqmmc))
4243 regulator_disable(mmc->supply.vqmmc);
4244undma:
4245 if (host->align_buffer)
4246 dma_free_coherent(mmc_dev(mmc), host->align_buffer_sz +
4247 host->adma_table_sz, host->align_buffer,
4248 host->align_addr);
4249 host->adma_table = NULL;
4250 host->align_buffer = NULL;
4251
4252 return ret;
4253}
4254EXPORT_SYMBOL_GPL(sdhci_setup_host);
4255
4256void sdhci_cleanup_host(struct sdhci_host *host)
4257{
4258 struct mmc_host *mmc = host->mmc;
4259
4260 if (!IS_ERR(mmc->supply.vqmmc))
4261 regulator_disable(mmc->supply.vqmmc);
4262
4263 if (host->align_buffer)
4264 dma_free_coherent(mmc_dev(mmc), host->align_buffer_sz +
4265 host->adma_table_sz, host->align_buffer,
4266 host->align_addr);
4267 host->adma_table = NULL;
4268 host->align_buffer = NULL;
4269}
4270EXPORT_SYMBOL_GPL(sdhci_cleanup_host);
4271
4272int __sdhci_add_host(struct sdhci_host *host)
4273{
4274 unsigned int flags = WQ_UNBOUND | WQ_MEM_RECLAIM | WQ_HIGHPRI;
4275 struct mmc_host *mmc = host->mmc;
4276 int ret;
4277
4278 host->complete_wq = alloc_workqueue("sdhci", flags, 0);
4279 if (!host->complete_wq)
4280 return -ENOMEM;
4281
4282 INIT_WORK(&host->complete_work, sdhci_complete_work);
4283
4284 timer_setup(&host->timer, sdhci_timeout_timer, 0);
4285 timer_setup(&host->data_timer, sdhci_timeout_data_timer, 0);
4286
4287 init_waitqueue_head(&host->buf_ready_int);
4288
4289 sdhci_init(host, 0);
4290
4291 ret = request_threaded_irq(host->irq, sdhci_irq, sdhci_thread_irq,
4292 IRQF_SHARED, mmc_hostname(mmc), host);
4293 if (ret) {
4294 pr_err("%s: Failed to request IRQ %d: %d\n",
4295 mmc_hostname(mmc), host->irq, ret);
4296 goto unwq;
4297 }
4298
4299 ret = sdhci_led_register(host);
4300 if (ret) {
4301 pr_err("%s: Failed to register LED device: %d\n",
4302 mmc_hostname(mmc), ret);
4303 goto unirq;
4304 }
4305
4306 ret = mmc_add_host(mmc);
4307 if (ret)
4308 goto unled;
4309
4310 pr_info("%s: SDHCI controller on %s [%s] using %s\n",
4311 mmc_hostname(mmc), host->hw_name, dev_name(mmc_dev(mmc)),
4312 (host->flags & SDHCI_USE_ADMA) ?
4313 (host->flags & SDHCI_USE_64_BIT_DMA) ? "ADMA 64-bit" : "ADMA" :
4314 (host->flags & SDHCI_USE_SDMA) ? "DMA" : "PIO");
4315
4316 sdhci_enable_card_detection(host);
4317
4318 return 0;
4319
4320unled:
4321 sdhci_led_unregister(host);
4322unirq:
4323 sdhci_do_reset(host, SDHCI_RESET_ALL);
4324 sdhci_writel(host, 0, SDHCI_INT_ENABLE);
4325 sdhci_writel(host, 0, SDHCI_SIGNAL_ENABLE);
4326 free_irq(host->irq, host);
4327unwq:
4328 destroy_workqueue(host->complete_wq);
4329
4330 return ret;
4331}
4332EXPORT_SYMBOL_GPL(__sdhci_add_host);
4333
4334int sdhci_add_host(struct sdhci_host *host)
4335{
4336 int ret;
4337
4338 ret = sdhci_setup_host(host);
4339 if (ret)
4340 return ret;
4341
4342 ret = __sdhci_add_host(host);
4343 if (ret)
4344 goto cleanup;
4345
4346 return 0;
4347
4348cleanup:
4349 sdhci_cleanup_host(host);
4350
4351 return ret;
4352}
4353EXPORT_SYMBOL_GPL(sdhci_add_host);
4354
4355void sdhci_remove_host(struct sdhci_host *host, int dead)
4356{
4357 struct mmc_host *mmc = host->mmc;
4358 unsigned long flags;
4359
4360 if (dead) {
4361 spin_lock_irqsave(&host->lock, flags);
4362
4363 host->flags |= SDHCI_DEVICE_DEAD;
4364
4365 if (sdhci_has_requests(host)) {
4366 pr_err("%s: Controller removed during "
4367 " transfer!\n", mmc_hostname(mmc));
4368 sdhci_error_out_mrqs(host, -ENOMEDIUM);
4369 }
4370
4371 spin_unlock_irqrestore(&host->lock, flags);
4372 }
4373
4374 sdhci_disable_card_detection(host);
4375
4376 mmc_remove_host(mmc);
4377
4378 sdhci_led_unregister(host);
4379
4380 if (!dead)
4381 sdhci_do_reset(host, SDHCI_RESET_ALL);
4382
4383 sdhci_writel(host, 0, SDHCI_INT_ENABLE);
4384 sdhci_writel(host, 0, SDHCI_SIGNAL_ENABLE);
4385 free_irq(host->irq, host);
4386
4387 del_timer_sync(&host->timer);
4388 del_timer_sync(&host->data_timer);
4389
4390 destroy_workqueue(host->complete_wq);
4391
4392 if (!IS_ERR(mmc->supply.vqmmc))
4393 regulator_disable(mmc->supply.vqmmc);
4394
4395 if (host->align_buffer)
4396 dma_free_coherent(mmc_dev(mmc), host->align_buffer_sz +
4397 host->adma_table_sz, host->align_buffer,
4398 host->align_addr);
4399
4400 host->adma_table = NULL;
4401 host->align_buffer = NULL;
4402}
4403
4404EXPORT_SYMBOL_GPL(sdhci_remove_host);
4405
4406void sdhci_free_host(struct sdhci_host *host)
4407{
4408 mmc_free_host(host->mmc);
4409}
4410
4411EXPORT_SYMBOL_GPL(sdhci_free_host);
4412
4413/*****************************************************************************\
4414 * *
4415 * Driver init/exit *
4416 * *
4417\*****************************************************************************/
4418
4419static int __init sdhci_drv_init(void)
4420{
4421 pr_info(DRIVER_NAME
4422 ": Secure Digital Host Controller Interface driver\n");
4423 pr_info(DRIVER_NAME ": Copyright(c) Pierre Ossman\n");
4424
4425 return 0;
4426}
4427
4428static void __exit sdhci_drv_exit(void)
4429{
4430}
4431
4432module_init(sdhci_drv_init);
4433module_exit(sdhci_drv_exit);
4434
4435module_param(debug_quirks, uint, 0444);
4436module_param(debug_quirks2, uint, 0444);
4437
4438MODULE_AUTHOR("Pierre Ossman <pierre@ossman.eu>");
4439MODULE_DESCRIPTION("Secure Digital Host Controller Interface core driver");
4440MODULE_LICENSE("GPL");
4441
4442MODULE_PARM_DESC(debug_quirks, "Force certain quirks.");
4443MODULE_PARM_DESC(debug_quirks2, "Force certain other quirks.");