Loading...
1menu "EEPROM support"
2
3config EEPROM_AT24
4 tristate "I2C EEPROMs from most vendors"
5 depends on I2C && SYSFS
6 help
7 Enable this driver to get read/write support to most I2C EEPROMs,
8 after you configure the driver to know about each EEPROM on
9 your target board. Use these generic chip names, instead of
10 vendor-specific ones like at24c64 or 24lc02:
11
12 24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08,
13 24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024
14
15 Unless you like data loss puzzles, always be sure that any chip
16 you configure as a 24c32 (32 kbit) or larger is NOT really a
17 24c16 (16 kbit) or smaller, and vice versa. Marking the chip
18 as read-only won't help recover from this. Also, if your chip
19 has any software write-protect mechanism you may want to review the
20 code to make sure this driver won't turn it on by accident.
21
22 If you use this with an SMBus adapter instead of an I2C adapter,
23 full functionality is not available. Only smaller devices are
24 supported (24c16 and below, max 4 kByte).
25
26 This driver can also be built as a module. If so, the module
27 will be called at24.
28
29config EEPROM_AT25
30 tristate "SPI EEPROMs from most vendors"
31 depends on SPI && SYSFS
32 help
33 Enable this driver to get read/write support to most SPI EEPROMs,
34 after you configure the board init code to know about each eeprom
35 on your target board.
36
37 This driver can also be built as a module. If so, the module
38 will be called at25.
39
40config EEPROM_LEGACY
41 tristate "Old I2C EEPROM reader"
42 depends on I2C && SYSFS
43 help
44 If you say yes here you get read-only access to the EEPROM data
45 available on modern memory DIMMs and Sony Vaio laptops via I2C. Such
46 EEPROMs could theoretically be available on other devices as well.
47
48 This driver can also be built as a module. If so, the module
49 will be called eeprom.
50
51config EEPROM_MAX6875
52 tristate "Maxim MAX6874/5 power supply supervisor"
53 depends on I2C && EXPERIMENTAL
54 help
55 If you say yes here you get read-only support for the user EEPROM of
56 the Maxim MAX6874/5 EEPROM-programmable, quad power-supply
57 sequencer/supervisor.
58
59 All other features of this chip should be accessed via i2c-dev.
60
61 This driver can also be built as a module. If so, the module
62 will be called max6875.
63
64
65config EEPROM_93CX6
66 tristate "EEPROM 93CX6 support"
67 help
68 This is a driver for the EEPROM chipsets 93c46 and 93c66.
69 The driver supports both read as well as write commands.
70
71 If unsure, say N.
72
73config EEPROM_93XX46
74 tristate "Microwire EEPROM 93XX46 support"
75 depends on SPI && SYSFS
76 help
77 Driver for the microwire EEPROM chipsets 93xx46x. The driver
78 supports both read and write commands and also the command to
79 erase the whole EEPROM.
80
81 This driver can also be built as a module. If so, the module
82 will be called eeprom_93xx46.
83
84 If unsure, say N.
85
86config EEPROM_DIGSY_MTC_CFG
87 bool "DigsyMTC display configuration EEPROMs device"
88 depends on PPC_MPC5200_GPIO && GPIOLIB && SPI_GPIO
89 help
90 This option enables access to display configuration EEPROMs
91 on digsy_mtc board. You have to additionally select Microwire
92 EEPROM 93XX46 driver. sysfs entries will be created for that
93 EEPROM allowing to read/write the configuration data or to
94 erase the whole EEPROM.
95
96 If unsure, say N.
97
98endmenu
1# SPDX-License-Identifier: GPL-2.0-only
2menu "EEPROM support"
3
4config EEPROM_AT24
5 tristate "I2C EEPROMs / RAMs / ROMs from most vendors"
6 depends on I2C && SYSFS
7 select NVMEM
8 select NVMEM_SYSFS
9 select REGMAP_I2C
10 help
11 Enable this driver to get read/write support to most I2C EEPROMs
12 and compatible devices like FRAMs, SRAMs, ROMs etc. After you
13 configure the driver to know about each chip on your target
14 board. Use these generic chip names, instead of vendor-specific
15 ones like at24c64, 24lc02 or fm24c04:
16
17 24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08,
18 24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024, 24c2048
19
20 Unless you like data loss puzzles, always be sure that any chip
21 you configure as a 24c32 (32 kbit) or larger is NOT really a
22 24c16 (16 kbit) or smaller, and vice versa. Marking the chip
23 as read-only won't help recover from this. Also, if your chip
24 has any software write-protect mechanism you may want to review the
25 code to make sure this driver won't turn it on by accident.
26
27 If you use this with an SMBus adapter instead of an I2C adapter,
28 full functionality is not available. Only smaller devices are
29 supported (24c16 and below, max 4 kByte).
30
31 This driver can also be built as a module. If so, the module
32 will be called at24.
33
34config EEPROM_AT25
35 tristate "SPI EEPROMs (FRAMs) from most vendors"
36 depends on SPI && SYSFS
37 select NVMEM
38 select NVMEM_SYSFS
39 help
40 Enable this driver to get read/write support to most SPI EEPROMs
41 and Cypress FRAMs,
42 after you configure the board init code to know about each eeprom
43 on your target board.
44
45 This driver can also be built as a module. If so, the module
46 will be called at25.
47
48config EEPROM_LEGACY
49 tristate "Old I2C EEPROM reader (DEPRECATED)"
50 depends on I2C && SYSFS
51 help
52 If you say yes here you get read-only access to the EEPROM data
53 available on modern memory DIMMs and Sony Vaio laptops via I2C. Such
54 EEPROMs could theoretically be available on other devices as well.
55
56 This driver is deprecated and will be removed soon, please use the
57 better at24 driver instead.
58
59 This driver can also be built as a module. If so, the module
60 will be called eeprom.
61
62config EEPROM_MAX6875
63 tristate "Maxim MAX6874/5 power supply supervisor"
64 depends on I2C
65 help
66 If you say yes here you get read-only support for the user EEPROM of
67 the Maxim MAX6874/5 EEPROM-programmable, quad power-supply
68 sequencer/supervisor.
69
70 All other features of this chip should be accessed via i2c-dev.
71
72 This driver can also be built as a module. If so, the module
73 will be called max6875.
74
75
76config EEPROM_93CX6
77 tristate "EEPROM 93CX6 support"
78 help
79 This is a driver for the EEPROM chipsets 93c46 and 93c66.
80 The driver supports both read as well as write commands.
81
82 If unsure, say N.
83
84config EEPROM_93XX46
85 tristate "Microwire EEPROM 93XX46 support"
86 depends on SPI && SYSFS
87 select REGMAP
88 select NVMEM
89 select NVMEM_SYSFS
90 help
91 Driver for the microwire EEPROM chipsets 93xx46x. The driver
92 supports both read and write commands and also the command to
93 erase the whole EEPROM.
94
95 This driver can also be built as a module. If so, the module
96 will be called eeprom_93xx46.
97
98 If unsure, say N.
99
100config EEPROM_DIGSY_MTC_CFG
101 bool "DigsyMTC display configuration EEPROMs device"
102 depends on GPIO_MPC5200 && SPI_GPIO
103 help
104 This option enables access to display configuration EEPROMs
105 on digsy_mtc board. You have to additionally select Microwire
106 EEPROM 93XX46 driver. sysfs entries will be created for that
107 EEPROM allowing to read/write the configuration data or to
108 erase the whole EEPROM.
109
110 If unsure, say N.
111
112config EEPROM_IDT_89HPESX
113 tristate "IDT 89HPESx PCIe-swtiches EEPROM / CSR support"
114 depends on I2C && SYSFS
115 help
116 Enable this driver to get read/write access to EEPROM / CSRs
117 over IDT PCIe-swtich i2c-slave interface.
118
119 This driver can also be built as a module. If so, the module
120 will be called idt_89hpesx.
121
122config EEPROM_EE1004
123 tristate "SPD EEPROMs on DDR4 memory modules"
124 depends on I2C && SYSFS
125 help
126 Enable this driver to get read support to SPD EEPROMs following
127 the JEDEC EE1004 standard. These are typically found on DDR4
128 SDRAM memory modules.
129
130 This driver can also be built as a module. If so, the module
131 will be called ee1004.
132
133endmenu