Loading...
1/* Low-level parallel port routines for the Multiface 3 card
2 *
3 * Author: Joerg Dorchain <joerg@dorchain.net>
4 *
5 * (C) The elitist m68k Users(TM)
6 *
7 * based on the existing parport_amiga and lp_mfc
8 *
9 *
10 * From the MFC3 documentation:
11 *
12 * Miscellaneous PIA Details
13 * -------------------------
14 *
15 * The two open-drain interrupt outputs /IRQA and /IRQB are routed to
16 * /INT2 of the Z2 bus.
17 *
18 * The CPU data bus of the PIA (D0-D7) is connected to D8-D15 on the Z2
19 * bus. This means that any PIA registers are accessed at even addresses.
20 *
21 * Centronics Pin Connections for the PIA
22 * --------------------------------------
23 *
24 * The following table shows the connections between the PIA and the
25 * Centronics interface connector. These connections implement a single, but
26 * very complete, Centronics type interface. The Pin column gives the pin
27 * numbers of the PIA. The Centronics pin numbers can be found in the section
28 * "Parallel Connectors".
29 *
30 *
31 * Pin | PIA | Dir | Centronics Names
32 * -------+-----+-----+---------------------------------------------------------
33 * 19 | CB2 | --> | /STROBE (aka /DRDY)
34 * 10-17 | PBx | <-> | DATA0 - DATA7
35 * 18 | CB1 | <-- | /ACK
36 * 40 | CA1 | <-- | BUSY
37 * 3 | PA1 | <-- | PAPER-OUT (aka POUT)
38 * 4 | PA2 | <-- | SELECTED (aka SEL)
39 * 9 | PA7 | --> | /INIT (aka /RESET or /INPUT-PRIME)
40 * 6 | PA4 | <-- | /ERROR (aka /FAULT)
41 * 7 | PA5 | --> | DIR (aka /SELECT-IN)
42 * 8 | PA6 | --> | /AUTO-FEED-XT
43 * 39 | CA2 | --> | open
44 * 5 | PA3 | <-- | /ACK (same as CB1!)
45 * 2 | PA0 | <-- | BUSY (same as CA1!)
46 * -------+-----+-----+---------------------------------------------------------
47 *
48 * Should be enough to understand some of the driver.
49 *
50 * Per convention for normal use the port registers are visible.
51 * If you need the data direction registers, restore the value in the
52 * control register.
53 */
54
55#include "multiface.h"
56#include <linux/module.h>
57#include <linux/init.h>
58#include <linux/parport.h>
59#include <linux/delay.h>
60#include <linux/mc6821.h>
61#include <linux/zorro.h>
62#include <linux/interrupt.h>
63#include <asm/setup.h>
64#include <asm/amigahw.h>
65#include <asm/irq.h>
66#include <asm/amigaints.h>
67
68/* Maximum Number of Cards supported */
69#define MAX_MFC 5
70
71#undef DEBUG
72#ifdef DEBUG
73#define DPRINTK printk
74#else
75static inline int DPRINTK(void *nothing, ...) {return 0;}
76#endif
77
78static struct parport *this_port[MAX_MFC] = {NULL, };
79static volatile int dummy; /* for trigger readds */
80
81#define pia(dev) ((struct pia *)(dev->base))
82static struct parport_operations pp_mfc3_ops;
83
84static void mfc3_write_data(struct parport *p, unsigned char data)
85{
86DPRINTK(KERN_DEBUG "write_data %c\n",data);
87
88 dummy = pia(p)->pprb; /* clears irq bit */
89 /* Triggers also /STROBE.*/
90 pia(p)->pprb = data;
91}
92
93static unsigned char mfc3_read_data(struct parport *p)
94{
95 /* clears interrupt bit. Triggers also /STROBE. */
96 return pia(p)->pprb;
97}
98
99static unsigned char control_pc_to_mfc3(unsigned char control)
100{
101 unsigned char ret = 32|64;
102
103 if (control & PARPORT_CONTROL_SELECT) /* XXX: What is SELECP? */
104 ret &= ~32; /* /SELECT_IN */
105 if (control & PARPORT_CONTROL_INIT) /* INITP */
106 ret |= 128;
107 if (control & PARPORT_CONTROL_AUTOFD) /* AUTOLF */
108 ret &= ~64;
109 if (control & PARPORT_CONTROL_STROBE) /* Strobe */
110 /* Handled directly by hardware */;
111 return ret;
112}
113
114static unsigned char control_mfc3_to_pc(unsigned char control)
115{
116 unsigned char ret = PARPORT_CONTROL_STROBE
117 | PARPORT_CONTROL_AUTOFD | PARPORT_CONTROL_SELECT;
118
119 if (control & 128) /* /INITP */
120 ret |= PARPORT_CONTROL_INIT;
121 if (control & 64) /* /AUTOLF */
122 ret &= ~PARPORT_CONTROL_AUTOFD;
123 if (control & 32) /* /SELECT_IN */
124 ret &= ~PARPORT_CONTROL_SELECT;
125 return ret;
126}
127
128static void mfc3_write_control(struct parport *p, unsigned char control)
129{
130DPRINTK(KERN_DEBUG "write_control %02x\n",control);
131 pia(p)->ppra = (pia(p)->ppra & 0x1f) | control_pc_to_mfc3(control);
132}
133
134static unsigned char mfc3_read_control( struct parport *p)
135{
136DPRINTK(KERN_DEBUG "read_control \n");
137 return control_mfc3_to_pc(pia(p)->ppra & 0xe0);
138}
139
140static unsigned char mfc3_frob_control( struct parport *p, unsigned char mask, unsigned char val)
141{
142 unsigned char old;
143
144DPRINTK(KERN_DEBUG "frob_control mask %02x, value %02x\n",mask,val);
145 old = mfc3_read_control(p);
146 mfc3_write_control(p, (old & ~mask) ^ val);
147 return old;
148}
149
150#if 0 /* currently unused */
151static unsigned char status_pc_to_mfc3(unsigned char status)
152{
153 unsigned char ret = 1;
154
155 if (status & PARPORT_STATUS_BUSY) /* Busy */
156 ret &= ~1;
157 if (status & PARPORT_STATUS_ACK) /* Ack */
158 ret |= 8;
159 if (status & PARPORT_STATUS_PAPEROUT) /* PaperOut */
160 ret |= 2;
161 if (status & PARPORT_STATUS_SELECT) /* select */
162 ret |= 4;
163 if (status & PARPORT_STATUS_ERROR) /* error */
164 ret |= 16;
165 return ret;
166}
167#endif
168
169static unsigned char status_mfc3_to_pc(unsigned char status)
170{
171 unsigned char ret = PARPORT_STATUS_BUSY;
172
173 if (status & 1) /* Busy */
174 ret &= ~PARPORT_STATUS_BUSY;
175 if (status & 2) /* PaperOut */
176 ret |= PARPORT_STATUS_PAPEROUT;
177 if (status & 4) /* Selected */
178 ret |= PARPORT_STATUS_SELECT;
179 if (status & 8) /* Ack */
180 ret |= PARPORT_STATUS_ACK;
181 if (status & 16) /* /ERROR */
182 ret |= PARPORT_STATUS_ERROR;
183
184 return ret;
185}
186
187#if 0 /* currently unused */
188static void mfc3_write_status( struct parport *p, unsigned char status)
189{
190DPRINTK(KERN_DEBUG "write_status %02x\n",status);
191 pia(p)->ppra = (pia(p)->ppra & 0xe0) | status_pc_to_mfc3(status);
192}
193#endif
194
195static unsigned char mfc3_read_status(struct parport *p)
196{
197 unsigned char status;
198
199 status = status_mfc3_to_pc(pia(p)->ppra & 0x1f);
200DPRINTK(KERN_DEBUG "read_status %02x\n", status);
201 return status;
202}
203
204#if 0 /* currently unused */
205static void mfc3_change_mode( struct parport *p, int m)
206{
207 /* XXX: This port only has one mode, and I am
208 not sure about the corresponding PC-style mode*/
209}
210#endif
211
212static int use_cnt = 0;
213
214static irqreturn_t mfc3_interrupt(int irq, void *dev_id)
215{
216 int i;
217
218 for( i = 0; i < MAX_MFC; i++)
219 if (this_port[i] != NULL)
220 if (pia(this_port[i])->crb & 128) { /* Board caused interrupt */
221 dummy = pia(this_port[i])->pprb; /* clear irq bit */
222 parport_generic_irq(this_port[i]);
223 }
224 return IRQ_HANDLED;
225}
226
227static void mfc3_enable_irq(struct parport *p)
228{
229 pia(p)->crb |= PIA_C1_ENABLE_IRQ;
230}
231
232static void mfc3_disable_irq(struct parport *p)
233{
234 pia(p)->crb &= ~PIA_C1_ENABLE_IRQ;
235}
236
237static void mfc3_data_forward(struct parport *p)
238{
239 DPRINTK(KERN_DEBUG "forward\n");
240 pia(p)->crb &= ~PIA_DDR; /* make data direction register visible */
241 pia(p)->pddrb = 255; /* all pins output */
242 pia(p)->crb |= PIA_DDR; /* make data register visible - default */
243}
244
245static void mfc3_data_reverse(struct parport *p)
246{
247 DPRINTK(KERN_DEBUG "reverse\n");
248 pia(p)->crb &= ~PIA_DDR; /* make data direction register visible */
249 pia(p)->pddrb = 0; /* all pins input */
250 pia(p)->crb |= PIA_DDR; /* make data register visible - default */
251}
252
253static void mfc3_init_state(struct pardevice *dev, struct parport_state *s)
254{
255 s->u.amiga.data = 0;
256 s->u.amiga.datadir = 255;
257 s->u.amiga.status = 0;
258 s->u.amiga.statusdir = 0xe0;
259}
260
261static void mfc3_save_state(struct parport *p, struct parport_state *s)
262{
263 s->u.amiga.data = pia(p)->pprb;
264 pia(p)->crb &= ~PIA_DDR;
265 s->u.amiga.datadir = pia(p)->pddrb;
266 pia(p)->crb |= PIA_DDR;
267 s->u.amiga.status = pia(p)->ppra;
268 pia(p)->cra &= ~PIA_DDR;
269 s->u.amiga.statusdir = pia(p)->pddrb;
270 pia(p)->cra |= PIA_DDR;
271}
272
273static void mfc3_restore_state(struct parport *p, struct parport_state *s)
274{
275 pia(p)->pprb = s->u.amiga.data;
276 pia(p)->crb &= ~PIA_DDR;
277 pia(p)->pddrb = s->u.amiga.datadir;
278 pia(p)->crb |= PIA_DDR;
279 pia(p)->ppra = s->u.amiga.status;
280 pia(p)->cra &= ~PIA_DDR;
281 pia(p)->pddrb = s->u.amiga.statusdir;
282 pia(p)->cra |= PIA_DDR;
283}
284
285static struct parport_operations pp_mfc3_ops = {
286 .write_data = mfc3_write_data,
287 .read_data = mfc3_read_data,
288
289 .write_control = mfc3_write_control,
290 .read_control = mfc3_read_control,
291 .frob_control = mfc3_frob_control,
292
293 .read_status = mfc3_read_status,
294
295 .enable_irq = mfc3_enable_irq,
296 .disable_irq = mfc3_disable_irq,
297
298 .data_forward = mfc3_data_forward,
299 .data_reverse = mfc3_data_reverse,
300
301 .init_state = mfc3_init_state,
302 .save_state = mfc3_save_state,
303 .restore_state = mfc3_restore_state,
304
305 .epp_write_data = parport_ieee1284_epp_write_data,
306 .epp_read_data = parport_ieee1284_epp_read_data,
307 .epp_write_addr = parport_ieee1284_epp_write_addr,
308 .epp_read_addr = parport_ieee1284_epp_read_addr,
309
310 .ecp_write_data = parport_ieee1284_ecp_write_data,
311 .ecp_read_data = parport_ieee1284_ecp_read_data,
312 .ecp_write_addr = parport_ieee1284_ecp_write_addr,
313
314 .compat_write_data = parport_ieee1284_write_compat,
315 .nibble_read_data = parport_ieee1284_read_nibble,
316 .byte_read_data = parport_ieee1284_read_byte,
317
318 .owner = THIS_MODULE,
319};
320
321/* ----------- Initialisation code --------------------------------- */
322
323static int __init parport_mfc3_init(void)
324{
325 struct parport *p;
326 int pias = 0;
327 struct pia *pp;
328 struct zorro_dev *z = NULL;
329
330 if (!MACH_IS_AMIGA)
331 return -ENODEV;
332
333 while ((z = zorro_find_device(ZORRO_PROD_BSC_MULTIFACE_III, z))) {
334 unsigned long piabase = z->resource.start+PIABASE;
335 if (!request_mem_region(piabase, sizeof(struct pia), "PIA"))
336 continue;
337
338 pp = (struct pia *)ZTWO_VADDR(piabase);
339 pp->crb = 0;
340 pp->pddrb = 255; /* all data pins output */
341 pp->crb = PIA_DDR|32|8;
342 dummy = pp->pddrb; /* reading clears interrupt */
343 pp->cra = 0;
344 pp->pddra = 0xe0; /* /RESET, /DIR ,/AUTO-FEED output */
345 pp->cra = PIA_DDR;
346 pp->ppra = 0; /* reset printer */
347 udelay(10);
348 pp->ppra = 128;
349 p = parport_register_port((unsigned long)pp, IRQ_AMIGA_PORTS,
350 PARPORT_DMA_NONE, &pp_mfc3_ops);
351 if (!p)
352 goto out_port;
353
354 if (p->irq != PARPORT_IRQ_NONE) {
355 if (use_cnt++ == 0)
356 if (request_irq(IRQ_AMIGA_PORTS, mfc3_interrupt, IRQF_SHARED, p->name, &pp_mfc3_ops))
357 goto out_irq;
358 }
359 p->dev = &z->dev;
360
361 this_port[pias++] = p;
362 printk(KERN_INFO "%s: Multiface III port using irq\n", p->name);
363 /* XXX: set operating mode */
364
365 p->private_data = (void *)piabase;
366 parport_announce_port (p);
367
368 if (pias >= MAX_MFC)
369 break;
370 continue;
371
372 out_irq:
373 parport_put_port(p);
374 out_port:
375 release_mem_region(piabase, sizeof(struct pia));
376 }
377
378 return pias ? 0 : -ENODEV;
379}
380
381static void __exit parport_mfc3_exit(void)
382{
383 int i;
384
385 for (i = 0; i < MAX_MFC; i++) {
386 if (!this_port[i])
387 continue;
388 parport_remove_port(this_port[i]);
389 if (this_port[i]->irq != PARPORT_IRQ_NONE) {
390 if (--use_cnt == 0)
391 free_irq(IRQ_AMIGA_PORTS, &pp_mfc3_ops);
392 }
393 release_mem_region(ZTWO_PADDR(this_port[i]->private_data), sizeof(struct pia));
394 parport_put_port(this_port[i]);
395 }
396}
397
398
399MODULE_AUTHOR("Joerg Dorchain <joerg@dorchain.net>");
400MODULE_DESCRIPTION("Parport Driver for Multiface 3 expansion cards Paralllel Port");
401MODULE_SUPPORTED_DEVICE("Multiface 3 Parallel Port");
402MODULE_LICENSE("GPL");
403
404module_init(parport_mfc3_init)
405module_exit(parport_mfc3_exit)
1// SPDX-License-Identifier: GPL-2.0-only
2/* Low-level parallel port routines for the Multiface 3 card
3 *
4 * Author: Joerg Dorchain <joerg@dorchain.net>
5 *
6 * (C) The elitist m68k Users(TM)
7 *
8 * based on the existing parport_amiga and lp_mfc
9 *
10 *
11 * From the MFC3 documentation:
12 *
13 * Miscellaneous PIA Details
14 * -------------------------
15 *
16 * The two open-drain interrupt outputs /IRQA and /IRQB are routed to
17 * /INT2 of the Z2 bus.
18 *
19 * The CPU data bus of the PIA (D0-D7) is connected to D8-D15 on the Z2
20 * bus. This means that any PIA registers are accessed at even addresses.
21 *
22 * Centronics Pin Connections for the PIA
23 * --------------------------------------
24 *
25 * The following table shows the connections between the PIA and the
26 * Centronics interface connector. These connections implement a single, but
27 * very complete, Centronics type interface. The Pin column gives the pin
28 * numbers of the PIA. The Centronics pin numbers can be found in the section
29 * "Parallel Connectors".
30 *
31 *
32 * Pin | PIA | Dir | Centronics Names
33 * -------+-----+-----+---------------------------------------------------------
34 * 19 | CB2 | --> | /STROBE (aka /DRDY)
35 * 10-17 | PBx | <-> | DATA0 - DATA7
36 * 18 | CB1 | <-- | /ACK
37 * 40 | CA1 | <-- | BUSY
38 * 3 | PA1 | <-- | PAPER-OUT (aka POUT)
39 * 4 | PA2 | <-- | SELECTED (aka SEL)
40 * 9 | PA7 | --> | /INIT (aka /RESET or /INPUT-PRIME)
41 * 6 | PA4 | <-- | /ERROR (aka /FAULT)
42 * 7 | PA5 | --> | DIR (aka /SELECT-IN)
43 * 8 | PA6 | --> | /AUTO-FEED-XT
44 * 39 | CA2 | --> | open
45 * 5 | PA3 | <-- | /ACK (same as CB1!)
46 * 2 | PA0 | <-- | BUSY (same as CA1!)
47 * -------+-----+-----+---------------------------------------------------------
48 *
49 * Should be enough to understand some of the driver.
50 *
51 * Per convention for normal use the port registers are visible.
52 * If you need the data direction registers, restore the value in the
53 * control register.
54 */
55
56#include "multiface.h"
57#include <linux/module.h>
58#include <linux/init.h>
59#include <linux/parport.h>
60#include <linux/delay.h>
61#include <linux/mc6821.h>
62#include <linux/zorro.h>
63#include <linux/interrupt.h>
64#include <asm/setup.h>
65#include <asm/amigahw.h>
66#include <asm/irq.h>
67#include <asm/amigaints.h>
68
69/* Maximum Number of Cards supported */
70#define MAX_MFC 5
71
72#undef DEBUG
73
74static struct parport *this_port[MAX_MFC] = {NULL, };
75static volatile int dummy; /* for trigger readds */
76
77#define pia(dev) ((struct pia *)(dev->base))
78static struct parport_operations pp_mfc3_ops;
79
80static void mfc3_write_data(struct parport *p, unsigned char data)
81{
82 pr_debug("write_data %c\n", data);
83
84 dummy = pia(p)->pprb; /* clears irq bit */
85 /* Triggers also /STROBE.*/
86 pia(p)->pprb = data;
87}
88
89static unsigned char mfc3_read_data(struct parport *p)
90{
91 /* clears interrupt bit. Triggers also /STROBE. */
92 return pia(p)->pprb;
93}
94
95static unsigned char control_pc_to_mfc3(unsigned char control)
96{
97 unsigned char ret = 32|64;
98
99 if (control & PARPORT_CONTROL_SELECT) /* XXX: What is SELECP? */
100 ret &= ~32; /* /SELECT_IN */
101 if (control & PARPORT_CONTROL_INIT) /* INITP */
102 ret |= 128;
103 if (control & PARPORT_CONTROL_AUTOFD) /* AUTOLF */
104 ret &= ~64;
105 /* PARPORT_CONTROL_STROBE handled directly by hardware */
106 return ret;
107}
108
109static unsigned char control_mfc3_to_pc(unsigned char control)
110{
111 unsigned char ret = PARPORT_CONTROL_STROBE
112 | PARPORT_CONTROL_AUTOFD | PARPORT_CONTROL_SELECT;
113
114 if (control & 128) /* /INITP */
115 ret |= PARPORT_CONTROL_INIT;
116 if (control & 64) /* /AUTOLF */
117 ret &= ~PARPORT_CONTROL_AUTOFD;
118 if (control & 32) /* /SELECT_IN */
119 ret &= ~PARPORT_CONTROL_SELECT;
120 return ret;
121}
122
123static void mfc3_write_control(struct parport *p, unsigned char control)
124{
125 pr_debug("write_control %02x\n", control);
126 pia(p)->ppra = (pia(p)->ppra & 0x1f) | control_pc_to_mfc3(control);
127}
128
129static unsigned char mfc3_read_control( struct parport *p)
130{
131 pr_debug("read_control\n");
132 return control_mfc3_to_pc(pia(p)->ppra & 0xe0);
133}
134
135static unsigned char mfc3_frob_control( struct parport *p, unsigned char mask, unsigned char val)
136{
137 unsigned char old;
138
139 pr_debug("frob_control mask %02x, value %02x\n", mask, val);
140 old = mfc3_read_control(p);
141 mfc3_write_control(p, (old & ~mask) ^ val);
142 return old;
143}
144
145static unsigned char status_mfc3_to_pc(unsigned char status)
146{
147 unsigned char ret = PARPORT_STATUS_BUSY;
148
149 if (status & 1) /* Busy */
150 ret &= ~PARPORT_STATUS_BUSY;
151 if (status & 2) /* PaperOut */
152 ret |= PARPORT_STATUS_PAPEROUT;
153 if (status & 4) /* Selected */
154 ret |= PARPORT_STATUS_SELECT;
155 if (status & 8) /* Ack */
156 ret |= PARPORT_STATUS_ACK;
157 if (status & 16) /* /ERROR */
158 ret |= PARPORT_STATUS_ERROR;
159
160 return ret;
161}
162
163static unsigned char mfc3_read_status(struct parport *p)
164{
165 unsigned char status;
166
167 status = status_mfc3_to_pc(pia(p)->ppra & 0x1f);
168 pr_debug("read_status %02x\n", status);
169 return status;
170}
171
172static int use_cnt;
173
174static irqreturn_t mfc3_interrupt(int irq, void *dev_id)
175{
176 int i;
177
178 for( i = 0; i < MAX_MFC; i++)
179 if (this_port[i] != NULL)
180 if (pia(this_port[i])->crb & 128) { /* Board caused interrupt */
181 dummy = pia(this_port[i])->pprb; /* clear irq bit */
182 parport_generic_irq(this_port[i]);
183 }
184 return IRQ_HANDLED;
185}
186
187static void mfc3_enable_irq(struct parport *p)
188{
189 pia(p)->crb |= PIA_C1_ENABLE_IRQ;
190}
191
192static void mfc3_disable_irq(struct parport *p)
193{
194 pia(p)->crb &= ~PIA_C1_ENABLE_IRQ;
195}
196
197static void mfc3_data_forward(struct parport *p)
198{
199 pr_debug("forward\n");
200 pia(p)->crb &= ~PIA_DDR; /* make data direction register visible */
201 pia(p)->pddrb = 255; /* all pins output */
202 pia(p)->crb |= PIA_DDR; /* make data register visible - default */
203}
204
205static void mfc3_data_reverse(struct parport *p)
206{
207 pr_debug("reverse\n");
208 pia(p)->crb &= ~PIA_DDR; /* make data direction register visible */
209 pia(p)->pddrb = 0; /* all pins input */
210 pia(p)->crb |= PIA_DDR; /* make data register visible - default */
211}
212
213static void mfc3_init_state(struct pardevice *dev, struct parport_state *s)
214{
215 s->u.amiga.data = 0;
216 s->u.amiga.datadir = 255;
217 s->u.amiga.status = 0;
218 s->u.amiga.statusdir = 0xe0;
219}
220
221static void mfc3_save_state(struct parport *p, struct parport_state *s)
222{
223 s->u.amiga.data = pia(p)->pprb;
224 pia(p)->crb &= ~PIA_DDR;
225 s->u.amiga.datadir = pia(p)->pddrb;
226 pia(p)->crb |= PIA_DDR;
227 s->u.amiga.status = pia(p)->ppra;
228 pia(p)->cra &= ~PIA_DDR;
229 s->u.amiga.statusdir = pia(p)->pddrb;
230 pia(p)->cra |= PIA_DDR;
231}
232
233static void mfc3_restore_state(struct parport *p, struct parport_state *s)
234{
235 pia(p)->pprb = s->u.amiga.data;
236 pia(p)->crb &= ~PIA_DDR;
237 pia(p)->pddrb = s->u.amiga.datadir;
238 pia(p)->crb |= PIA_DDR;
239 pia(p)->ppra = s->u.amiga.status;
240 pia(p)->cra &= ~PIA_DDR;
241 pia(p)->pddrb = s->u.amiga.statusdir;
242 pia(p)->cra |= PIA_DDR;
243}
244
245static struct parport_operations pp_mfc3_ops = {
246 .write_data = mfc3_write_data,
247 .read_data = mfc3_read_data,
248
249 .write_control = mfc3_write_control,
250 .read_control = mfc3_read_control,
251 .frob_control = mfc3_frob_control,
252
253 .read_status = mfc3_read_status,
254
255 .enable_irq = mfc3_enable_irq,
256 .disable_irq = mfc3_disable_irq,
257
258 .data_forward = mfc3_data_forward,
259 .data_reverse = mfc3_data_reverse,
260
261 .init_state = mfc3_init_state,
262 .save_state = mfc3_save_state,
263 .restore_state = mfc3_restore_state,
264
265 .epp_write_data = parport_ieee1284_epp_write_data,
266 .epp_read_data = parport_ieee1284_epp_read_data,
267 .epp_write_addr = parport_ieee1284_epp_write_addr,
268 .epp_read_addr = parport_ieee1284_epp_read_addr,
269
270 .ecp_write_data = parport_ieee1284_ecp_write_data,
271 .ecp_read_data = parport_ieee1284_ecp_read_data,
272 .ecp_write_addr = parport_ieee1284_ecp_write_addr,
273
274 .compat_write_data = parport_ieee1284_write_compat,
275 .nibble_read_data = parport_ieee1284_read_nibble,
276 .byte_read_data = parport_ieee1284_read_byte,
277
278 .owner = THIS_MODULE,
279};
280
281/* ----------- Initialisation code --------------------------------- */
282
283static int __init parport_mfc3_init(void)
284{
285 struct parport *p;
286 int pias = 0;
287 struct pia *pp;
288 struct zorro_dev *z = NULL;
289
290 if (!MACH_IS_AMIGA)
291 return -ENODEV;
292
293 while ((z = zorro_find_device(ZORRO_PROD_BSC_MULTIFACE_III, z))) {
294 unsigned long piabase = z->resource.start+PIABASE;
295 if (!request_mem_region(piabase, sizeof(struct pia), "PIA"))
296 continue;
297
298 pp = ZTWO_VADDR(piabase);
299 pp->crb = 0;
300 pp->pddrb = 255; /* all data pins output */
301 pp->crb = PIA_DDR|32|8;
302 dummy = pp->pddrb; /* reading clears interrupt */
303 pp->cra = 0;
304 pp->pddra = 0xe0; /* /RESET, /DIR ,/AUTO-FEED output */
305 pp->cra = PIA_DDR;
306 pp->ppra = 0; /* reset printer */
307 udelay(10);
308 pp->ppra = 128;
309 p = parport_register_port((unsigned long)pp, IRQ_AMIGA_PORTS,
310 PARPORT_DMA_NONE, &pp_mfc3_ops);
311 if (!p)
312 goto out_port;
313
314 if (p->irq != PARPORT_IRQ_NONE) {
315 if (use_cnt++ == 0)
316 if (request_irq(IRQ_AMIGA_PORTS, mfc3_interrupt, IRQF_SHARED, p->name, &pp_mfc3_ops))
317 goto out_irq;
318 }
319 p->dev = &z->dev;
320
321 this_port[pias++] = p;
322 pr_info("%s: Multiface III port using irq\n", p->name);
323 /* XXX: set operating mode */
324
325 p->private_data = (void *)piabase;
326 parport_announce_port (p);
327
328 if (pias >= MAX_MFC)
329 break;
330 continue;
331
332 out_irq:
333 parport_put_port(p);
334 out_port:
335 release_mem_region(piabase, sizeof(struct pia));
336 }
337
338 return pias ? 0 : -ENODEV;
339}
340
341static void __exit parport_mfc3_exit(void)
342{
343 int i;
344
345 for (i = 0; i < MAX_MFC; i++) {
346 if (!this_port[i])
347 continue;
348 parport_remove_port(this_port[i]);
349 if (this_port[i]->irq != PARPORT_IRQ_NONE) {
350 if (--use_cnt == 0)
351 free_irq(IRQ_AMIGA_PORTS, &pp_mfc3_ops);
352 }
353 release_mem_region(ZTWO_PADDR(this_port[i]->private_data), sizeof(struct pia));
354 parport_put_port(this_port[i]);
355 }
356}
357
358
359MODULE_AUTHOR("Joerg Dorchain <joerg@dorchain.net>");
360MODULE_DESCRIPTION("Parport Driver for Multiface 3 expansion cards Parallel Port");
361MODULE_LICENSE("GPL");
362
363module_init(parport_mfc3_init)
364module_exit(parport_mfc3_exit)