Loading...
1/*
2 * $Id: synclink.c,v 4.38 2005/11/07 16:30:34 paulkf Exp $
3 *
4 * Device driver for Microgate SyncLink ISA and PCI
5 * high speed multiprotocol serial adapters.
6 *
7 * written by Paul Fulghum for Microgate Corporation
8 * paulkf@microgate.com
9 *
10 * Microgate and SyncLink are trademarks of Microgate Corporation
11 *
12 * Derived from serial.c written by Theodore Ts'o and Linus Torvalds
13 *
14 * Original release 01/11/99
15 *
16 * This code is released under the GNU General Public License (GPL)
17 *
18 * This driver is primarily intended for use in synchronous
19 * HDLC mode. Asynchronous mode is also provided.
20 *
21 * When operating in synchronous mode, each call to mgsl_write()
22 * contains exactly one complete HDLC frame. Calling mgsl_put_char
23 * will start assembling an HDLC frame that will not be sent until
24 * mgsl_flush_chars or mgsl_write is called.
25 *
26 * Synchronous receive data is reported as complete frames. To accomplish
27 * this, the TTY flip buffer is bypassed (too small to hold largest
28 * frame and may fragment frames) and the line discipline
29 * receive entry point is called directly.
30 *
31 * This driver has been tested with a slightly modified ppp.c driver
32 * for synchronous PPP.
33 *
34 * 2000/02/16
35 * Added interface for syncppp.c driver (an alternate synchronous PPP
36 * implementation that also supports Cisco HDLC). Each device instance
37 * registers as a tty device AND a network device (if dosyncppp option
38 * is set for the device). The functionality is determined by which
39 * device interface is opened.
40 *
41 * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
42 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
43 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
44 * DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
45 * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
46 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
47 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
48 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
49 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
50 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
51 * OF THE POSSIBILITY OF SUCH DAMAGE.
52 */
53
54#if defined(__i386__)
55# define BREAKPOINT() asm(" int $3");
56#else
57# define BREAKPOINT() { }
58#endif
59
60#define MAX_ISA_DEVICES 10
61#define MAX_PCI_DEVICES 10
62#define MAX_TOTAL_DEVICES 20
63
64#include <linux/module.h>
65#include <linux/errno.h>
66#include <linux/signal.h>
67#include <linux/sched.h>
68#include <linux/timer.h>
69#include <linux/interrupt.h>
70#include <linux/pci.h>
71#include <linux/tty.h>
72#include <linux/tty_flip.h>
73#include <linux/serial.h>
74#include <linux/major.h>
75#include <linux/string.h>
76#include <linux/fcntl.h>
77#include <linux/ptrace.h>
78#include <linux/ioport.h>
79#include <linux/mm.h>
80#include <linux/seq_file.h>
81#include <linux/slab.h>
82#include <linux/delay.h>
83#include <linux/netdevice.h>
84#include <linux/vmalloc.h>
85#include <linux/init.h>
86#include <linux/ioctl.h>
87#include <linux/synclink.h>
88
89#include <asm/system.h>
90#include <asm/io.h>
91#include <asm/irq.h>
92#include <asm/dma.h>
93#include <linux/bitops.h>
94#include <asm/types.h>
95#include <linux/termios.h>
96#include <linux/workqueue.h>
97#include <linux/hdlc.h>
98#include <linux/dma-mapping.h>
99
100#if defined(CONFIG_HDLC) || (defined(CONFIG_HDLC_MODULE) && defined(CONFIG_SYNCLINK_MODULE))
101#define SYNCLINK_GENERIC_HDLC 1
102#else
103#define SYNCLINK_GENERIC_HDLC 0
104#endif
105
106#define GET_USER(error,value,addr) error = get_user(value,addr)
107#define COPY_FROM_USER(error,dest,src,size) error = copy_from_user(dest,src,size) ? -EFAULT : 0
108#define PUT_USER(error,value,addr) error = put_user(value,addr)
109#define COPY_TO_USER(error,dest,src,size) error = copy_to_user(dest,src,size) ? -EFAULT : 0
110
111#include <asm/uaccess.h>
112
113#define RCLRVALUE 0xffff
114
115static MGSL_PARAMS default_params = {
116 MGSL_MODE_HDLC, /* unsigned long mode */
117 0, /* unsigned char loopback; */
118 HDLC_FLAG_UNDERRUN_ABORT15, /* unsigned short flags; */
119 HDLC_ENCODING_NRZI_SPACE, /* unsigned char encoding; */
120 0, /* unsigned long clock_speed; */
121 0xff, /* unsigned char addr_filter; */
122 HDLC_CRC_16_CCITT, /* unsigned short crc_type; */
123 HDLC_PREAMBLE_LENGTH_8BITS, /* unsigned char preamble_length; */
124 HDLC_PREAMBLE_PATTERN_NONE, /* unsigned char preamble; */
125 9600, /* unsigned long data_rate; */
126 8, /* unsigned char data_bits; */
127 1, /* unsigned char stop_bits; */
128 ASYNC_PARITY_NONE /* unsigned char parity; */
129};
130
131#define SHARED_MEM_ADDRESS_SIZE 0x40000
132#define BUFFERLISTSIZE 4096
133#define DMABUFFERSIZE 4096
134#define MAXRXFRAMES 7
135
136typedef struct _DMABUFFERENTRY
137{
138 u32 phys_addr; /* 32-bit flat physical address of data buffer */
139 volatile u16 count; /* buffer size/data count */
140 volatile u16 status; /* Control/status field */
141 volatile u16 rcc; /* character count field */
142 u16 reserved; /* padding required by 16C32 */
143 u32 link; /* 32-bit flat link to next buffer entry */
144 char *virt_addr; /* virtual address of data buffer */
145 u32 phys_entry; /* physical address of this buffer entry */
146 dma_addr_t dma_addr;
147} DMABUFFERENTRY, *DMAPBUFFERENTRY;
148
149/* The queue of BH actions to be performed */
150
151#define BH_RECEIVE 1
152#define BH_TRANSMIT 2
153#define BH_STATUS 4
154
155#define IO_PIN_SHUTDOWN_LIMIT 100
156
157struct _input_signal_events {
158 int ri_up;
159 int ri_down;
160 int dsr_up;
161 int dsr_down;
162 int dcd_up;
163 int dcd_down;
164 int cts_up;
165 int cts_down;
166};
167
168/* transmit holding buffer definitions*/
169#define MAX_TX_HOLDING_BUFFERS 5
170struct tx_holding_buffer {
171 int buffer_size;
172 unsigned char * buffer;
173};
174
175
176/*
177 * Device instance data structure
178 */
179
180struct mgsl_struct {
181 int magic;
182 struct tty_port port;
183 int line;
184 int hw_version;
185
186 struct mgsl_icount icount;
187
188 int timeout;
189 int x_char; /* xon/xoff character */
190 u16 read_status_mask;
191 u16 ignore_status_mask;
192 unsigned char *xmit_buf;
193 int xmit_head;
194 int xmit_tail;
195 int xmit_cnt;
196
197 wait_queue_head_t status_event_wait_q;
198 wait_queue_head_t event_wait_q;
199 struct timer_list tx_timer; /* HDLC transmit timeout timer */
200 struct mgsl_struct *next_device; /* device list link */
201
202 spinlock_t irq_spinlock; /* spinlock for synchronizing with ISR */
203 struct work_struct task; /* task structure for scheduling bh */
204
205 u32 EventMask; /* event trigger mask */
206 u32 RecordedEvents; /* pending events */
207
208 u32 max_frame_size; /* as set by device config */
209
210 u32 pending_bh;
211
212 bool bh_running; /* Protection from multiple */
213 int isr_overflow;
214 bool bh_requested;
215
216 int dcd_chkcount; /* check counts to prevent */
217 int cts_chkcount; /* too many IRQs if a signal */
218 int dsr_chkcount; /* is floating */
219 int ri_chkcount;
220
221 char *buffer_list; /* virtual address of Rx & Tx buffer lists */
222 u32 buffer_list_phys;
223 dma_addr_t buffer_list_dma_addr;
224
225 unsigned int rx_buffer_count; /* count of total allocated Rx buffers */
226 DMABUFFERENTRY *rx_buffer_list; /* list of receive buffer entries */
227 unsigned int current_rx_buffer;
228
229 int num_tx_dma_buffers; /* number of tx dma frames required */
230 int tx_dma_buffers_used;
231 unsigned int tx_buffer_count; /* count of total allocated Tx buffers */
232 DMABUFFERENTRY *tx_buffer_list; /* list of transmit buffer entries */
233 int start_tx_dma_buffer; /* tx dma buffer to start tx dma operation */
234 int current_tx_buffer; /* next tx dma buffer to be loaded */
235
236 unsigned char *intermediate_rxbuffer;
237
238 int num_tx_holding_buffers; /* number of tx holding buffer allocated */
239 int get_tx_holding_index; /* next tx holding buffer for adapter to load */
240 int put_tx_holding_index; /* next tx holding buffer to store user request */
241 int tx_holding_count; /* number of tx holding buffers waiting */
242 struct tx_holding_buffer tx_holding_buffers[MAX_TX_HOLDING_BUFFERS];
243
244 bool rx_enabled;
245 bool rx_overflow;
246 bool rx_rcc_underrun;
247
248 bool tx_enabled;
249 bool tx_active;
250 u32 idle_mode;
251
252 u16 cmr_value;
253 u16 tcsr_value;
254
255 char device_name[25]; /* device instance name */
256
257 unsigned int bus_type; /* expansion bus type (ISA,EISA,PCI) */
258 unsigned char bus; /* expansion bus number (zero based) */
259 unsigned char function; /* PCI device number */
260
261 unsigned int io_base; /* base I/O address of adapter */
262 unsigned int io_addr_size; /* size of the I/O address range */
263 bool io_addr_requested; /* true if I/O address requested */
264
265 unsigned int irq_level; /* interrupt level */
266 unsigned long irq_flags;
267 bool irq_requested; /* true if IRQ requested */
268
269 unsigned int dma_level; /* DMA channel */
270 bool dma_requested; /* true if dma channel requested */
271
272 u16 mbre_bit;
273 u16 loopback_bits;
274 u16 usc_idle_mode;
275
276 MGSL_PARAMS params; /* communications parameters */
277
278 unsigned char serial_signals; /* current serial signal states */
279
280 bool irq_occurred; /* for diagnostics use */
281 unsigned int init_error; /* Initialization startup error (DIAGS) */
282 int fDiagnosticsmode; /* Driver in Diagnostic mode? (DIAGS) */
283
284 u32 last_mem_alloc;
285 unsigned char* memory_base; /* shared memory address (PCI only) */
286 u32 phys_memory_base;
287 bool shared_mem_requested;
288
289 unsigned char* lcr_base; /* local config registers (PCI only) */
290 u32 phys_lcr_base;
291 u32 lcr_offset;
292 bool lcr_mem_requested;
293
294 u32 misc_ctrl_value;
295 char flag_buf[MAX_ASYNC_BUFFER_SIZE];
296 char char_buf[MAX_ASYNC_BUFFER_SIZE];
297 bool drop_rts_on_tx_done;
298
299 bool loopmode_insert_requested;
300 bool loopmode_send_done_requested;
301
302 struct _input_signal_events input_signal_events;
303
304 /* generic HDLC device parts */
305 int netcount;
306 spinlock_t netlock;
307
308#if SYNCLINK_GENERIC_HDLC
309 struct net_device *netdev;
310#endif
311};
312
313#define MGSL_MAGIC 0x5401
314
315/*
316 * The size of the serial xmit buffer is 1 page, or 4096 bytes
317 */
318#ifndef SERIAL_XMIT_SIZE
319#define SERIAL_XMIT_SIZE 4096
320#endif
321
322/*
323 * These macros define the offsets used in calculating the
324 * I/O address of the specified USC registers.
325 */
326
327
328#define DCPIN 2 /* Bit 1 of I/O address */
329#define SDPIN 4 /* Bit 2 of I/O address */
330
331#define DCAR 0 /* DMA command/address register */
332#define CCAR SDPIN /* channel command/address register */
333#define DATAREG DCPIN + SDPIN /* serial data register */
334#define MSBONLY 0x41
335#define LSBONLY 0x40
336
337/*
338 * These macros define the register address (ordinal number)
339 * used for writing address/value pairs to the USC.
340 */
341
342#define CMR 0x02 /* Channel mode Register */
343#define CCSR 0x04 /* Channel Command/status Register */
344#define CCR 0x06 /* Channel Control Register */
345#define PSR 0x08 /* Port status Register */
346#define PCR 0x0a /* Port Control Register */
347#define TMDR 0x0c /* Test mode Data Register */
348#define TMCR 0x0e /* Test mode Control Register */
349#define CMCR 0x10 /* Clock mode Control Register */
350#define HCR 0x12 /* Hardware Configuration Register */
351#define IVR 0x14 /* Interrupt Vector Register */
352#define IOCR 0x16 /* Input/Output Control Register */
353#define ICR 0x18 /* Interrupt Control Register */
354#define DCCR 0x1a /* Daisy Chain Control Register */
355#define MISR 0x1c /* Misc Interrupt status Register */
356#define SICR 0x1e /* status Interrupt Control Register */
357#define RDR 0x20 /* Receive Data Register */
358#define RMR 0x22 /* Receive mode Register */
359#define RCSR 0x24 /* Receive Command/status Register */
360#define RICR 0x26 /* Receive Interrupt Control Register */
361#define RSR 0x28 /* Receive Sync Register */
362#define RCLR 0x2a /* Receive count Limit Register */
363#define RCCR 0x2c /* Receive Character count Register */
364#define TC0R 0x2e /* Time Constant 0 Register */
365#define TDR 0x30 /* Transmit Data Register */
366#define TMR 0x32 /* Transmit mode Register */
367#define TCSR 0x34 /* Transmit Command/status Register */
368#define TICR 0x36 /* Transmit Interrupt Control Register */
369#define TSR 0x38 /* Transmit Sync Register */
370#define TCLR 0x3a /* Transmit count Limit Register */
371#define TCCR 0x3c /* Transmit Character count Register */
372#define TC1R 0x3e /* Time Constant 1 Register */
373
374
375/*
376 * MACRO DEFINITIONS FOR DMA REGISTERS
377 */
378
379#define DCR 0x06 /* DMA Control Register (shared) */
380#define DACR 0x08 /* DMA Array count Register (shared) */
381#define BDCR 0x12 /* Burst/Dwell Control Register (shared) */
382#define DIVR 0x14 /* DMA Interrupt Vector Register (shared) */
383#define DICR 0x18 /* DMA Interrupt Control Register (shared) */
384#define CDIR 0x1a /* Clear DMA Interrupt Register (shared) */
385#define SDIR 0x1c /* Set DMA Interrupt Register (shared) */
386
387#define TDMR 0x02 /* Transmit DMA mode Register */
388#define TDIAR 0x1e /* Transmit DMA Interrupt Arm Register */
389#define TBCR 0x2a /* Transmit Byte count Register */
390#define TARL 0x2c /* Transmit Address Register (low) */
391#define TARU 0x2e /* Transmit Address Register (high) */
392#define NTBCR 0x3a /* Next Transmit Byte count Register */
393#define NTARL 0x3c /* Next Transmit Address Register (low) */
394#define NTARU 0x3e /* Next Transmit Address Register (high) */
395
396#define RDMR 0x82 /* Receive DMA mode Register (non-shared) */
397#define RDIAR 0x9e /* Receive DMA Interrupt Arm Register */
398#define RBCR 0xaa /* Receive Byte count Register */
399#define RARL 0xac /* Receive Address Register (low) */
400#define RARU 0xae /* Receive Address Register (high) */
401#define NRBCR 0xba /* Next Receive Byte count Register */
402#define NRARL 0xbc /* Next Receive Address Register (low) */
403#define NRARU 0xbe /* Next Receive Address Register (high) */
404
405
406/*
407 * MACRO DEFINITIONS FOR MODEM STATUS BITS
408 */
409
410#define MODEMSTATUS_DTR 0x80
411#define MODEMSTATUS_DSR 0x40
412#define MODEMSTATUS_RTS 0x20
413#define MODEMSTATUS_CTS 0x10
414#define MODEMSTATUS_RI 0x04
415#define MODEMSTATUS_DCD 0x01
416
417
418/*
419 * Channel Command/Address Register (CCAR) Command Codes
420 */
421
422#define RTCmd_Null 0x0000
423#define RTCmd_ResetHighestIus 0x1000
424#define RTCmd_TriggerChannelLoadDma 0x2000
425#define RTCmd_TriggerRxDma 0x2800
426#define RTCmd_TriggerTxDma 0x3000
427#define RTCmd_TriggerRxAndTxDma 0x3800
428#define RTCmd_PurgeRxFifo 0x4800
429#define RTCmd_PurgeTxFifo 0x5000
430#define RTCmd_PurgeRxAndTxFifo 0x5800
431#define RTCmd_LoadRcc 0x6800
432#define RTCmd_LoadTcc 0x7000
433#define RTCmd_LoadRccAndTcc 0x7800
434#define RTCmd_LoadTC0 0x8800
435#define RTCmd_LoadTC1 0x9000
436#define RTCmd_LoadTC0AndTC1 0x9800
437#define RTCmd_SerialDataLSBFirst 0xa000
438#define RTCmd_SerialDataMSBFirst 0xa800
439#define RTCmd_SelectBigEndian 0xb000
440#define RTCmd_SelectLittleEndian 0xb800
441
442
443/*
444 * DMA Command/Address Register (DCAR) Command Codes
445 */
446
447#define DmaCmd_Null 0x0000
448#define DmaCmd_ResetTxChannel 0x1000
449#define DmaCmd_ResetRxChannel 0x1200
450#define DmaCmd_StartTxChannel 0x2000
451#define DmaCmd_StartRxChannel 0x2200
452#define DmaCmd_ContinueTxChannel 0x3000
453#define DmaCmd_ContinueRxChannel 0x3200
454#define DmaCmd_PauseTxChannel 0x4000
455#define DmaCmd_PauseRxChannel 0x4200
456#define DmaCmd_AbortTxChannel 0x5000
457#define DmaCmd_AbortRxChannel 0x5200
458#define DmaCmd_InitTxChannel 0x7000
459#define DmaCmd_InitRxChannel 0x7200
460#define DmaCmd_ResetHighestDmaIus 0x8000
461#define DmaCmd_ResetAllChannels 0x9000
462#define DmaCmd_StartAllChannels 0xa000
463#define DmaCmd_ContinueAllChannels 0xb000
464#define DmaCmd_PauseAllChannels 0xc000
465#define DmaCmd_AbortAllChannels 0xd000
466#define DmaCmd_InitAllChannels 0xf000
467
468#define TCmd_Null 0x0000
469#define TCmd_ClearTxCRC 0x2000
470#define TCmd_SelectTicrTtsaData 0x4000
471#define TCmd_SelectTicrTxFifostatus 0x5000
472#define TCmd_SelectTicrIntLevel 0x6000
473#define TCmd_SelectTicrdma_level 0x7000
474#define TCmd_SendFrame 0x8000
475#define TCmd_SendAbort 0x9000
476#define TCmd_EnableDleInsertion 0xc000
477#define TCmd_DisableDleInsertion 0xd000
478#define TCmd_ClearEofEom 0xe000
479#define TCmd_SetEofEom 0xf000
480
481#define RCmd_Null 0x0000
482#define RCmd_ClearRxCRC 0x2000
483#define RCmd_EnterHuntmode 0x3000
484#define RCmd_SelectRicrRtsaData 0x4000
485#define RCmd_SelectRicrRxFifostatus 0x5000
486#define RCmd_SelectRicrIntLevel 0x6000
487#define RCmd_SelectRicrdma_level 0x7000
488
489/*
490 * Bits for enabling and disabling IRQs in Interrupt Control Register (ICR)
491 */
492
493#define RECEIVE_STATUS BIT5
494#define RECEIVE_DATA BIT4
495#define TRANSMIT_STATUS BIT3
496#define TRANSMIT_DATA BIT2
497#define IO_PIN BIT1
498#define MISC BIT0
499
500
501/*
502 * Receive status Bits in Receive Command/status Register RCSR
503 */
504
505#define RXSTATUS_SHORT_FRAME BIT8
506#define RXSTATUS_CODE_VIOLATION BIT8
507#define RXSTATUS_EXITED_HUNT BIT7
508#define RXSTATUS_IDLE_RECEIVED BIT6
509#define RXSTATUS_BREAK_RECEIVED BIT5
510#define RXSTATUS_ABORT_RECEIVED BIT5
511#define RXSTATUS_RXBOUND BIT4
512#define RXSTATUS_CRC_ERROR BIT3
513#define RXSTATUS_FRAMING_ERROR BIT3
514#define RXSTATUS_ABORT BIT2
515#define RXSTATUS_PARITY_ERROR BIT2
516#define RXSTATUS_OVERRUN BIT1
517#define RXSTATUS_DATA_AVAILABLE BIT0
518#define RXSTATUS_ALL 0x01f6
519#define usc_UnlatchRxstatusBits(a,b) usc_OutReg( (a), RCSR, (u16)((b) & RXSTATUS_ALL) )
520
521/*
522 * Values for setting transmit idle mode in
523 * Transmit Control/status Register (TCSR)
524 */
525#define IDLEMODE_FLAGS 0x0000
526#define IDLEMODE_ALT_ONE_ZERO 0x0100
527#define IDLEMODE_ZERO 0x0200
528#define IDLEMODE_ONE 0x0300
529#define IDLEMODE_ALT_MARK_SPACE 0x0500
530#define IDLEMODE_SPACE 0x0600
531#define IDLEMODE_MARK 0x0700
532#define IDLEMODE_MASK 0x0700
533
534/*
535 * IUSC revision identifiers
536 */
537#define IUSC_SL1660 0x4d44
538#define IUSC_PRE_SL1660 0x4553
539
540/*
541 * Transmit status Bits in Transmit Command/status Register (TCSR)
542 */
543
544#define TCSR_PRESERVE 0x0F00
545
546#define TCSR_UNDERWAIT BIT11
547#define TXSTATUS_PREAMBLE_SENT BIT7
548#define TXSTATUS_IDLE_SENT BIT6
549#define TXSTATUS_ABORT_SENT BIT5
550#define TXSTATUS_EOF_SENT BIT4
551#define TXSTATUS_EOM_SENT BIT4
552#define TXSTATUS_CRC_SENT BIT3
553#define TXSTATUS_ALL_SENT BIT2
554#define TXSTATUS_UNDERRUN BIT1
555#define TXSTATUS_FIFO_EMPTY BIT0
556#define TXSTATUS_ALL 0x00fa
557#define usc_UnlatchTxstatusBits(a,b) usc_OutReg( (a), TCSR, (u16)((a)->tcsr_value + ((b) & 0x00FF)) )
558
559
560#define MISCSTATUS_RXC_LATCHED BIT15
561#define MISCSTATUS_RXC BIT14
562#define MISCSTATUS_TXC_LATCHED BIT13
563#define MISCSTATUS_TXC BIT12
564#define MISCSTATUS_RI_LATCHED BIT11
565#define MISCSTATUS_RI BIT10
566#define MISCSTATUS_DSR_LATCHED BIT9
567#define MISCSTATUS_DSR BIT8
568#define MISCSTATUS_DCD_LATCHED BIT7
569#define MISCSTATUS_DCD BIT6
570#define MISCSTATUS_CTS_LATCHED BIT5
571#define MISCSTATUS_CTS BIT4
572#define MISCSTATUS_RCC_UNDERRUN BIT3
573#define MISCSTATUS_DPLL_NO_SYNC BIT2
574#define MISCSTATUS_BRG1_ZERO BIT1
575#define MISCSTATUS_BRG0_ZERO BIT0
576
577#define usc_UnlatchIostatusBits(a,b) usc_OutReg((a),MISR,(u16)((b) & 0xaaa0))
578#define usc_UnlatchMiscstatusBits(a,b) usc_OutReg((a),MISR,(u16)((b) & 0x000f))
579
580#define SICR_RXC_ACTIVE BIT15
581#define SICR_RXC_INACTIVE BIT14
582#define SICR_RXC (BIT15+BIT14)
583#define SICR_TXC_ACTIVE BIT13
584#define SICR_TXC_INACTIVE BIT12
585#define SICR_TXC (BIT13+BIT12)
586#define SICR_RI_ACTIVE BIT11
587#define SICR_RI_INACTIVE BIT10
588#define SICR_RI (BIT11+BIT10)
589#define SICR_DSR_ACTIVE BIT9
590#define SICR_DSR_INACTIVE BIT8
591#define SICR_DSR (BIT9+BIT8)
592#define SICR_DCD_ACTIVE BIT7
593#define SICR_DCD_INACTIVE BIT6
594#define SICR_DCD (BIT7+BIT6)
595#define SICR_CTS_ACTIVE BIT5
596#define SICR_CTS_INACTIVE BIT4
597#define SICR_CTS (BIT5+BIT4)
598#define SICR_RCC_UNDERFLOW BIT3
599#define SICR_DPLL_NO_SYNC BIT2
600#define SICR_BRG1_ZERO BIT1
601#define SICR_BRG0_ZERO BIT0
602
603void usc_DisableMasterIrqBit( struct mgsl_struct *info );
604void usc_EnableMasterIrqBit( struct mgsl_struct *info );
605void usc_EnableInterrupts( struct mgsl_struct *info, u16 IrqMask );
606void usc_DisableInterrupts( struct mgsl_struct *info, u16 IrqMask );
607void usc_ClearIrqPendingBits( struct mgsl_struct *info, u16 IrqMask );
608
609#define usc_EnableInterrupts( a, b ) \
610 usc_OutReg( (a), ICR, (u16)((usc_InReg((a),ICR) & 0xff00) + 0xc0 + (b)) )
611
612#define usc_DisableInterrupts( a, b ) \
613 usc_OutReg( (a), ICR, (u16)((usc_InReg((a),ICR) & 0xff00) + 0x80 + (b)) )
614
615#define usc_EnableMasterIrqBit(a) \
616 usc_OutReg( (a), ICR, (u16)((usc_InReg((a),ICR) & 0x0f00) + 0xb000) )
617
618#define usc_DisableMasterIrqBit(a) \
619 usc_OutReg( (a), ICR, (u16)(usc_InReg((a),ICR) & 0x7f00) )
620
621#define usc_ClearIrqPendingBits( a, b ) usc_OutReg( (a), DCCR, 0x40 + (b) )
622
623/*
624 * Transmit status Bits in Transmit Control status Register (TCSR)
625 * and Transmit Interrupt Control Register (TICR) (except BIT2, BIT0)
626 */
627
628#define TXSTATUS_PREAMBLE_SENT BIT7
629#define TXSTATUS_IDLE_SENT BIT6
630#define TXSTATUS_ABORT_SENT BIT5
631#define TXSTATUS_EOF BIT4
632#define TXSTATUS_CRC_SENT BIT3
633#define TXSTATUS_ALL_SENT BIT2
634#define TXSTATUS_UNDERRUN BIT1
635#define TXSTATUS_FIFO_EMPTY BIT0
636
637#define DICR_MASTER BIT15
638#define DICR_TRANSMIT BIT0
639#define DICR_RECEIVE BIT1
640
641#define usc_EnableDmaInterrupts(a,b) \
642 usc_OutDmaReg( (a), DICR, (u16)(usc_InDmaReg((a),DICR) | (b)) )
643
644#define usc_DisableDmaInterrupts(a,b) \
645 usc_OutDmaReg( (a), DICR, (u16)(usc_InDmaReg((a),DICR) & ~(b)) )
646
647#define usc_EnableStatusIrqs(a,b) \
648 usc_OutReg( (a), SICR, (u16)(usc_InReg((a),SICR) | (b)) )
649
650#define usc_DisablestatusIrqs(a,b) \
651 usc_OutReg( (a), SICR, (u16)(usc_InReg((a),SICR) & ~(b)) )
652
653/* Transmit status Bits in Transmit Control status Register (TCSR) */
654/* and Transmit Interrupt Control Register (TICR) (except BIT2, BIT0) */
655
656
657#define DISABLE_UNCONDITIONAL 0
658#define DISABLE_END_OF_FRAME 1
659#define ENABLE_UNCONDITIONAL 2
660#define ENABLE_AUTO_CTS 3
661#define ENABLE_AUTO_DCD 3
662#define usc_EnableTransmitter(a,b) \
663 usc_OutReg( (a), TMR, (u16)((usc_InReg((a),TMR) & 0xfffc) | (b)) )
664#define usc_EnableReceiver(a,b) \
665 usc_OutReg( (a), RMR, (u16)((usc_InReg((a),RMR) & 0xfffc) | (b)) )
666
667static u16 usc_InDmaReg( struct mgsl_struct *info, u16 Port );
668static void usc_OutDmaReg( struct mgsl_struct *info, u16 Port, u16 Value );
669static void usc_DmaCmd( struct mgsl_struct *info, u16 Cmd );
670
671static u16 usc_InReg( struct mgsl_struct *info, u16 Port );
672static void usc_OutReg( struct mgsl_struct *info, u16 Port, u16 Value );
673static void usc_RTCmd( struct mgsl_struct *info, u16 Cmd );
674void usc_RCmd( struct mgsl_struct *info, u16 Cmd );
675void usc_TCmd( struct mgsl_struct *info, u16 Cmd );
676
677#define usc_TCmd(a,b) usc_OutReg((a), TCSR, (u16)((a)->tcsr_value + (b)))
678#define usc_RCmd(a,b) usc_OutReg((a), RCSR, (b))
679
680#define usc_SetTransmitSyncChars(a,s0,s1) usc_OutReg((a), TSR, (u16)(((u16)s0<<8)|(u16)s1))
681
682static void usc_process_rxoverrun_sync( struct mgsl_struct *info );
683static void usc_start_receiver( struct mgsl_struct *info );
684static void usc_stop_receiver( struct mgsl_struct *info );
685
686static void usc_start_transmitter( struct mgsl_struct *info );
687static void usc_stop_transmitter( struct mgsl_struct *info );
688static void usc_set_txidle( struct mgsl_struct *info );
689static void usc_load_txfifo( struct mgsl_struct *info );
690
691static void usc_enable_aux_clock( struct mgsl_struct *info, u32 DataRate );
692static void usc_enable_loopback( struct mgsl_struct *info, int enable );
693
694static void usc_get_serial_signals( struct mgsl_struct *info );
695static void usc_set_serial_signals( struct mgsl_struct *info );
696
697static void usc_reset( struct mgsl_struct *info );
698
699static void usc_set_sync_mode( struct mgsl_struct *info );
700static void usc_set_sdlc_mode( struct mgsl_struct *info );
701static void usc_set_async_mode( struct mgsl_struct *info );
702static void usc_enable_async_clock( struct mgsl_struct *info, u32 DataRate );
703
704static void usc_loopback_frame( struct mgsl_struct *info );
705
706static void mgsl_tx_timeout(unsigned long context);
707
708
709static void usc_loopmode_cancel_transmit( struct mgsl_struct * info );
710static void usc_loopmode_insert_request( struct mgsl_struct * info );
711static int usc_loopmode_active( struct mgsl_struct * info);
712static void usc_loopmode_send_done( struct mgsl_struct * info );
713
714static int mgsl_ioctl_common(struct mgsl_struct *info, unsigned int cmd, unsigned long arg);
715
716#if SYNCLINK_GENERIC_HDLC
717#define dev_to_port(D) (dev_to_hdlc(D)->priv)
718static void hdlcdev_tx_done(struct mgsl_struct *info);
719static void hdlcdev_rx(struct mgsl_struct *info, char *buf, int size);
720static int hdlcdev_init(struct mgsl_struct *info);
721static void hdlcdev_exit(struct mgsl_struct *info);
722#endif
723
724/*
725 * Defines a BUS descriptor value for the PCI adapter
726 * local bus address ranges.
727 */
728
729#define BUS_DESCRIPTOR( WrHold, WrDly, RdDly, Nwdd, Nwad, Nxda, Nrdd, Nrad ) \
730(0x00400020 + \
731((WrHold) << 30) + \
732((WrDly) << 28) + \
733((RdDly) << 26) + \
734((Nwdd) << 20) + \
735((Nwad) << 15) + \
736((Nxda) << 13) + \
737((Nrdd) << 11) + \
738((Nrad) << 6) )
739
740static void mgsl_trace_block(struct mgsl_struct *info,const char* data, int count, int xmit);
741
742/*
743 * Adapter diagnostic routines
744 */
745static bool mgsl_register_test( struct mgsl_struct *info );
746static bool mgsl_irq_test( struct mgsl_struct *info );
747static bool mgsl_dma_test( struct mgsl_struct *info );
748static bool mgsl_memory_test( struct mgsl_struct *info );
749static int mgsl_adapter_test( struct mgsl_struct *info );
750
751/*
752 * device and resource management routines
753 */
754static int mgsl_claim_resources(struct mgsl_struct *info);
755static void mgsl_release_resources(struct mgsl_struct *info);
756static void mgsl_add_device(struct mgsl_struct *info);
757static struct mgsl_struct* mgsl_allocate_device(void);
758
759/*
760 * DMA buffer manupulation functions.
761 */
762static void mgsl_free_rx_frame_buffers( struct mgsl_struct *info, unsigned int StartIndex, unsigned int EndIndex );
763static bool mgsl_get_rx_frame( struct mgsl_struct *info );
764static bool mgsl_get_raw_rx_frame( struct mgsl_struct *info );
765static void mgsl_reset_rx_dma_buffers( struct mgsl_struct *info );
766static void mgsl_reset_tx_dma_buffers( struct mgsl_struct *info );
767static int num_free_tx_dma_buffers(struct mgsl_struct *info);
768static void mgsl_load_tx_dma_buffer( struct mgsl_struct *info, const char *Buffer, unsigned int BufferSize);
769static void mgsl_load_pci_memory(char* TargetPtr, const char* SourcePtr, unsigned short count);
770
771/*
772 * DMA and Shared Memory buffer allocation and formatting
773 */
774static int mgsl_allocate_dma_buffers(struct mgsl_struct *info);
775static void mgsl_free_dma_buffers(struct mgsl_struct *info);
776static int mgsl_alloc_frame_memory(struct mgsl_struct *info, DMABUFFERENTRY *BufferList,int Buffercount);
777static void mgsl_free_frame_memory(struct mgsl_struct *info, DMABUFFERENTRY *BufferList,int Buffercount);
778static int mgsl_alloc_buffer_list_memory(struct mgsl_struct *info);
779static void mgsl_free_buffer_list_memory(struct mgsl_struct *info);
780static int mgsl_alloc_intermediate_rxbuffer_memory(struct mgsl_struct *info);
781static void mgsl_free_intermediate_rxbuffer_memory(struct mgsl_struct *info);
782static int mgsl_alloc_intermediate_txbuffer_memory(struct mgsl_struct *info);
783static void mgsl_free_intermediate_txbuffer_memory(struct mgsl_struct *info);
784static bool load_next_tx_holding_buffer(struct mgsl_struct *info);
785static int save_tx_buffer_request(struct mgsl_struct *info,const char *Buffer, unsigned int BufferSize);
786
787/*
788 * Bottom half interrupt handlers
789 */
790static void mgsl_bh_handler(struct work_struct *work);
791static void mgsl_bh_receive(struct mgsl_struct *info);
792static void mgsl_bh_transmit(struct mgsl_struct *info);
793static void mgsl_bh_status(struct mgsl_struct *info);
794
795/*
796 * Interrupt handler routines and dispatch table.
797 */
798static void mgsl_isr_null( struct mgsl_struct *info );
799static void mgsl_isr_transmit_data( struct mgsl_struct *info );
800static void mgsl_isr_receive_data( struct mgsl_struct *info );
801static void mgsl_isr_receive_status( struct mgsl_struct *info );
802static void mgsl_isr_transmit_status( struct mgsl_struct *info );
803static void mgsl_isr_io_pin( struct mgsl_struct *info );
804static void mgsl_isr_misc( struct mgsl_struct *info );
805static void mgsl_isr_receive_dma( struct mgsl_struct *info );
806static void mgsl_isr_transmit_dma( struct mgsl_struct *info );
807
808typedef void (*isr_dispatch_func)(struct mgsl_struct *);
809
810static isr_dispatch_func UscIsrTable[7] =
811{
812 mgsl_isr_null,
813 mgsl_isr_misc,
814 mgsl_isr_io_pin,
815 mgsl_isr_transmit_data,
816 mgsl_isr_transmit_status,
817 mgsl_isr_receive_data,
818 mgsl_isr_receive_status
819};
820
821/*
822 * ioctl call handlers
823 */
824static int tiocmget(struct tty_struct *tty);
825static int tiocmset(struct tty_struct *tty,
826 unsigned int set, unsigned int clear);
827static int mgsl_get_stats(struct mgsl_struct * info, struct mgsl_icount
828 __user *user_icount);
829static int mgsl_get_params(struct mgsl_struct * info, MGSL_PARAMS __user *user_params);
830static int mgsl_set_params(struct mgsl_struct * info, MGSL_PARAMS __user *new_params);
831static int mgsl_get_txidle(struct mgsl_struct * info, int __user *idle_mode);
832static int mgsl_set_txidle(struct mgsl_struct * info, int idle_mode);
833static int mgsl_txenable(struct mgsl_struct * info, int enable);
834static int mgsl_txabort(struct mgsl_struct * info);
835static int mgsl_rxenable(struct mgsl_struct * info, int enable);
836static int mgsl_wait_event(struct mgsl_struct * info, int __user *mask);
837static int mgsl_loopmode_send_done( struct mgsl_struct * info );
838
839/* set non-zero on successful registration with PCI subsystem */
840static bool pci_registered;
841
842/*
843 * Global linked list of SyncLink devices
844 */
845static struct mgsl_struct *mgsl_device_list;
846static int mgsl_device_count;
847
848/*
849 * Set this param to non-zero to load eax with the
850 * .text section address and breakpoint on module load.
851 * This is useful for use with gdb and add-symbol-file command.
852 */
853static int break_on_load;
854
855/*
856 * Driver major number, defaults to zero to get auto
857 * assigned major number. May be forced as module parameter.
858 */
859static int ttymajor;
860
861/*
862 * Array of user specified options for ISA adapters.
863 */
864static int io[MAX_ISA_DEVICES];
865static int irq[MAX_ISA_DEVICES];
866static int dma[MAX_ISA_DEVICES];
867static int debug_level;
868static int maxframe[MAX_TOTAL_DEVICES];
869static int txdmabufs[MAX_TOTAL_DEVICES];
870static int txholdbufs[MAX_TOTAL_DEVICES];
871
872module_param(break_on_load, bool, 0);
873module_param(ttymajor, int, 0);
874module_param_array(io, int, NULL, 0);
875module_param_array(irq, int, NULL, 0);
876module_param_array(dma, int, NULL, 0);
877module_param(debug_level, int, 0);
878module_param_array(maxframe, int, NULL, 0);
879module_param_array(txdmabufs, int, NULL, 0);
880module_param_array(txholdbufs, int, NULL, 0);
881
882static char *driver_name = "SyncLink serial driver";
883static char *driver_version = "$Revision: 4.38 $";
884
885static int synclink_init_one (struct pci_dev *dev,
886 const struct pci_device_id *ent);
887static void synclink_remove_one (struct pci_dev *dev);
888
889static struct pci_device_id synclink_pci_tbl[] = {
890 { PCI_VENDOR_ID_MICROGATE, PCI_DEVICE_ID_MICROGATE_USC, PCI_ANY_ID, PCI_ANY_ID, },
891 { PCI_VENDOR_ID_MICROGATE, 0x0210, PCI_ANY_ID, PCI_ANY_ID, },
892 { 0, }, /* terminate list */
893};
894MODULE_DEVICE_TABLE(pci, synclink_pci_tbl);
895
896MODULE_LICENSE("GPL");
897
898static struct pci_driver synclink_pci_driver = {
899 .name = "synclink",
900 .id_table = synclink_pci_tbl,
901 .probe = synclink_init_one,
902 .remove = __devexit_p(synclink_remove_one),
903};
904
905static struct tty_driver *serial_driver;
906
907/* number of characters left in xmit buffer before we ask for more */
908#define WAKEUP_CHARS 256
909
910
911static void mgsl_change_params(struct mgsl_struct *info);
912static void mgsl_wait_until_sent(struct tty_struct *tty, int timeout);
913
914/*
915 * 1st function defined in .text section. Calling this function in
916 * init_module() followed by a breakpoint allows a remote debugger
917 * (gdb) to get the .text address for the add-symbol-file command.
918 * This allows remote debugging of dynamically loadable modules.
919 */
920static void* mgsl_get_text_ptr(void)
921{
922 return mgsl_get_text_ptr;
923}
924
925static inline int mgsl_paranoia_check(struct mgsl_struct *info,
926 char *name, const char *routine)
927{
928#ifdef MGSL_PARANOIA_CHECK
929 static const char *badmagic =
930 "Warning: bad magic number for mgsl struct (%s) in %s\n";
931 static const char *badinfo =
932 "Warning: null mgsl_struct for (%s) in %s\n";
933
934 if (!info) {
935 printk(badinfo, name, routine);
936 return 1;
937 }
938 if (info->magic != MGSL_MAGIC) {
939 printk(badmagic, name, routine);
940 return 1;
941 }
942#else
943 if (!info)
944 return 1;
945#endif
946 return 0;
947}
948
949/**
950 * line discipline callback wrappers
951 *
952 * The wrappers maintain line discipline references
953 * while calling into the line discipline.
954 *
955 * ldisc_receive_buf - pass receive data to line discipline
956 */
957
958static void ldisc_receive_buf(struct tty_struct *tty,
959 const __u8 *data, char *flags, int count)
960{
961 struct tty_ldisc *ld;
962 if (!tty)
963 return;
964 ld = tty_ldisc_ref(tty);
965 if (ld) {
966 if (ld->ops->receive_buf)
967 ld->ops->receive_buf(tty, data, flags, count);
968 tty_ldisc_deref(ld);
969 }
970}
971
972/* mgsl_stop() throttle (stop) transmitter
973 *
974 * Arguments: tty pointer to tty info structure
975 * Return Value: None
976 */
977static void mgsl_stop(struct tty_struct *tty)
978{
979 struct mgsl_struct *info = tty->driver_data;
980 unsigned long flags;
981
982 if (mgsl_paranoia_check(info, tty->name, "mgsl_stop"))
983 return;
984
985 if ( debug_level >= DEBUG_LEVEL_INFO )
986 printk("mgsl_stop(%s)\n",info->device_name);
987
988 spin_lock_irqsave(&info->irq_spinlock,flags);
989 if (info->tx_enabled)
990 usc_stop_transmitter(info);
991 spin_unlock_irqrestore(&info->irq_spinlock,flags);
992
993} /* end of mgsl_stop() */
994
995/* mgsl_start() release (start) transmitter
996 *
997 * Arguments: tty pointer to tty info structure
998 * Return Value: None
999 */
1000static void mgsl_start(struct tty_struct *tty)
1001{
1002 struct mgsl_struct *info = tty->driver_data;
1003 unsigned long flags;
1004
1005 if (mgsl_paranoia_check(info, tty->name, "mgsl_start"))
1006 return;
1007
1008 if ( debug_level >= DEBUG_LEVEL_INFO )
1009 printk("mgsl_start(%s)\n",info->device_name);
1010
1011 spin_lock_irqsave(&info->irq_spinlock,flags);
1012 if (!info->tx_enabled)
1013 usc_start_transmitter(info);
1014 spin_unlock_irqrestore(&info->irq_spinlock,flags);
1015
1016} /* end of mgsl_start() */
1017
1018/*
1019 * Bottom half work queue access functions
1020 */
1021
1022/* mgsl_bh_action() Return next bottom half action to perform.
1023 * Return Value: BH action code or 0 if nothing to do.
1024 */
1025static int mgsl_bh_action(struct mgsl_struct *info)
1026{
1027 unsigned long flags;
1028 int rc = 0;
1029
1030 spin_lock_irqsave(&info->irq_spinlock,flags);
1031
1032 if (info->pending_bh & BH_RECEIVE) {
1033 info->pending_bh &= ~BH_RECEIVE;
1034 rc = BH_RECEIVE;
1035 } else if (info->pending_bh & BH_TRANSMIT) {
1036 info->pending_bh &= ~BH_TRANSMIT;
1037 rc = BH_TRANSMIT;
1038 } else if (info->pending_bh & BH_STATUS) {
1039 info->pending_bh &= ~BH_STATUS;
1040 rc = BH_STATUS;
1041 }
1042
1043 if (!rc) {
1044 /* Mark BH routine as complete */
1045 info->bh_running = false;
1046 info->bh_requested = false;
1047 }
1048
1049 spin_unlock_irqrestore(&info->irq_spinlock,flags);
1050
1051 return rc;
1052}
1053
1054/*
1055 * Perform bottom half processing of work items queued by ISR.
1056 */
1057static void mgsl_bh_handler(struct work_struct *work)
1058{
1059 struct mgsl_struct *info =
1060 container_of(work, struct mgsl_struct, task);
1061 int action;
1062
1063 if (!info)
1064 return;
1065
1066 if ( debug_level >= DEBUG_LEVEL_BH )
1067 printk( "%s(%d):mgsl_bh_handler(%s) entry\n",
1068 __FILE__,__LINE__,info->device_name);
1069
1070 info->bh_running = true;
1071
1072 while((action = mgsl_bh_action(info)) != 0) {
1073
1074 /* Process work item */
1075 if ( debug_level >= DEBUG_LEVEL_BH )
1076 printk( "%s(%d):mgsl_bh_handler() work item action=%d\n",
1077 __FILE__,__LINE__,action);
1078
1079 switch (action) {
1080
1081 case BH_RECEIVE:
1082 mgsl_bh_receive(info);
1083 break;
1084 case BH_TRANSMIT:
1085 mgsl_bh_transmit(info);
1086 break;
1087 case BH_STATUS:
1088 mgsl_bh_status(info);
1089 break;
1090 default:
1091 /* unknown work item ID */
1092 printk("Unknown work item ID=%08X!\n", action);
1093 break;
1094 }
1095 }
1096
1097 if ( debug_level >= DEBUG_LEVEL_BH )
1098 printk( "%s(%d):mgsl_bh_handler(%s) exit\n",
1099 __FILE__,__LINE__,info->device_name);
1100}
1101
1102static void mgsl_bh_receive(struct mgsl_struct *info)
1103{
1104 bool (*get_rx_frame)(struct mgsl_struct *info) =
1105 (info->params.mode == MGSL_MODE_HDLC ? mgsl_get_rx_frame : mgsl_get_raw_rx_frame);
1106
1107 if ( debug_level >= DEBUG_LEVEL_BH )
1108 printk( "%s(%d):mgsl_bh_receive(%s)\n",
1109 __FILE__,__LINE__,info->device_name);
1110
1111 do
1112 {
1113 if (info->rx_rcc_underrun) {
1114 unsigned long flags;
1115 spin_lock_irqsave(&info->irq_spinlock,flags);
1116 usc_start_receiver(info);
1117 spin_unlock_irqrestore(&info->irq_spinlock,flags);
1118 return;
1119 }
1120 } while(get_rx_frame(info));
1121}
1122
1123static void mgsl_bh_transmit(struct mgsl_struct *info)
1124{
1125 struct tty_struct *tty = info->port.tty;
1126 unsigned long flags;
1127
1128 if ( debug_level >= DEBUG_LEVEL_BH )
1129 printk( "%s(%d):mgsl_bh_transmit() entry on %s\n",
1130 __FILE__,__LINE__,info->device_name);
1131
1132 if (tty)
1133 tty_wakeup(tty);
1134
1135 /* if transmitter idle and loopmode_send_done_requested
1136 * then start echoing RxD to TxD
1137 */
1138 spin_lock_irqsave(&info->irq_spinlock,flags);
1139 if ( !info->tx_active && info->loopmode_send_done_requested )
1140 usc_loopmode_send_done( info );
1141 spin_unlock_irqrestore(&info->irq_spinlock,flags);
1142}
1143
1144static void mgsl_bh_status(struct mgsl_struct *info)
1145{
1146 if ( debug_level >= DEBUG_LEVEL_BH )
1147 printk( "%s(%d):mgsl_bh_status() entry on %s\n",
1148 __FILE__,__LINE__,info->device_name);
1149
1150 info->ri_chkcount = 0;
1151 info->dsr_chkcount = 0;
1152 info->dcd_chkcount = 0;
1153 info->cts_chkcount = 0;
1154}
1155
1156/* mgsl_isr_receive_status()
1157 *
1158 * Service a receive status interrupt. The type of status
1159 * interrupt is indicated by the state of the RCSR.
1160 * This is only used for HDLC mode.
1161 *
1162 * Arguments: info pointer to device instance data
1163 * Return Value: None
1164 */
1165static void mgsl_isr_receive_status( struct mgsl_struct *info )
1166{
1167 u16 status = usc_InReg( info, RCSR );
1168
1169 if ( debug_level >= DEBUG_LEVEL_ISR )
1170 printk("%s(%d):mgsl_isr_receive_status status=%04X\n",
1171 __FILE__,__LINE__,status);
1172
1173 if ( (status & RXSTATUS_ABORT_RECEIVED) &&
1174 info->loopmode_insert_requested &&
1175 usc_loopmode_active(info) )
1176 {
1177 ++info->icount.rxabort;
1178 info->loopmode_insert_requested = false;
1179
1180 /* clear CMR:13 to start echoing RxD to TxD */
1181 info->cmr_value &= ~BIT13;
1182 usc_OutReg(info, CMR, info->cmr_value);
1183
1184 /* disable received abort irq (no longer required) */
1185 usc_OutReg(info, RICR,
1186 (usc_InReg(info, RICR) & ~RXSTATUS_ABORT_RECEIVED));
1187 }
1188
1189 if (status & (RXSTATUS_EXITED_HUNT + RXSTATUS_IDLE_RECEIVED)) {
1190 if (status & RXSTATUS_EXITED_HUNT)
1191 info->icount.exithunt++;
1192 if (status & RXSTATUS_IDLE_RECEIVED)
1193 info->icount.rxidle++;
1194 wake_up_interruptible(&info->event_wait_q);
1195 }
1196
1197 if (status & RXSTATUS_OVERRUN){
1198 info->icount.rxover++;
1199 usc_process_rxoverrun_sync( info );
1200 }
1201
1202 usc_ClearIrqPendingBits( info, RECEIVE_STATUS );
1203 usc_UnlatchRxstatusBits( info, status );
1204
1205} /* end of mgsl_isr_receive_status() */
1206
1207/* mgsl_isr_transmit_status()
1208 *
1209 * Service a transmit status interrupt
1210 * HDLC mode :end of transmit frame
1211 * Async mode:all data is sent
1212 * transmit status is indicated by bits in the TCSR.
1213 *
1214 * Arguments: info pointer to device instance data
1215 * Return Value: None
1216 */
1217static void mgsl_isr_transmit_status( struct mgsl_struct *info )
1218{
1219 u16 status = usc_InReg( info, TCSR );
1220
1221 if ( debug_level >= DEBUG_LEVEL_ISR )
1222 printk("%s(%d):mgsl_isr_transmit_status status=%04X\n",
1223 __FILE__,__LINE__,status);
1224
1225 usc_ClearIrqPendingBits( info, TRANSMIT_STATUS );
1226 usc_UnlatchTxstatusBits( info, status );
1227
1228 if ( status & (TXSTATUS_UNDERRUN | TXSTATUS_ABORT_SENT) )
1229 {
1230 /* finished sending HDLC abort. This may leave */
1231 /* the TxFifo with data from the aborted frame */
1232 /* so purge the TxFifo. Also shutdown the DMA */
1233 /* channel in case there is data remaining in */
1234 /* the DMA buffer */
1235 usc_DmaCmd( info, DmaCmd_ResetTxChannel );
1236 usc_RTCmd( info, RTCmd_PurgeTxFifo );
1237 }
1238
1239 if ( status & TXSTATUS_EOF_SENT )
1240 info->icount.txok++;
1241 else if ( status & TXSTATUS_UNDERRUN )
1242 info->icount.txunder++;
1243 else if ( status & TXSTATUS_ABORT_SENT )
1244 info->icount.txabort++;
1245 else
1246 info->icount.txunder++;
1247
1248 info->tx_active = false;
1249 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
1250 del_timer(&info->tx_timer);
1251
1252 if ( info->drop_rts_on_tx_done ) {
1253 usc_get_serial_signals( info );
1254 if ( info->serial_signals & SerialSignal_RTS ) {
1255 info->serial_signals &= ~SerialSignal_RTS;
1256 usc_set_serial_signals( info );
1257 }
1258 info->drop_rts_on_tx_done = false;
1259 }
1260
1261#if SYNCLINK_GENERIC_HDLC
1262 if (info->netcount)
1263 hdlcdev_tx_done(info);
1264 else
1265#endif
1266 {
1267 if (info->port.tty->stopped || info->port.tty->hw_stopped) {
1268 usc_stop_transmitter(info);
1269 return;
1270 }
1271 info->pending_bh |= BH_TRANSMIT;
1272 }
1273
1274} /* end of mgsl_isr_transmit_status() */
1275
1276/* mgsl_isr_io_pin()
1277 *
1278 * Service an Input/Output pin interrupt. The type of
1279 * interrupt is indicated by bits in the MISR
1280 *
1281 * Arguments: info pointer to device instance data
1282 * Return Value: None
1283 */
1284static void mgsl_isr_io_pin( struct mgsl_struct *info )
1285{
1286 struct mgsl_icount *icount;
1287 u16 status = usc_InReg( info, MISR );
1288
1289 if ( debug_level >= DEBUG_LEVEL_ISR )
1290 printk("%s(%d):mgsl_isr_io_pin status=%04X\n",
1291 __FILE__,__LINE__,status);
1292
1293 usc_ClearIrqPendingBits( info, IO_PIN );
1294 usc_UnlatchIostatusBits( info, status );
1295
1296 if (status & (MISCSTATUS_CTS_LATCHED | MISCSTATUS_DCD_LATCHED |
1297 MISCSTATUS_DSR_LATCHED | MISCSTATUS_RI_LATCHED) ) {
1298 icount = &info->icount;
1299 /* update input line counters */
1300 if (status & MISCSTATUS_RI_LATCHED) {
1301 if ((info->ri_chkcount)++ >= IO_PIN_SHUTDOWN_LIMIT)
1302 usc_DisablestatusIrqs(info,SICR_RI);
1303 icount->rng++;
1304 if ( status & MISCSTATUS_RI )
1305 info->input_signal_events.ri_up++;
1306 else
1307 info->input_signal_events.ri_down++;
1308 }
1309 if (status & MISCSTATUS_DSR_LATCHED) {
1310 if ((info->dsr_chkcount)++ >= IO_PIN_SHUTDOWN_LIMIT)
1311 usc_DisablestatusIrqs(info,SICR_DSR);
1312 icount->dsr++;
1313 if ( status & MISCSTATUS_DSR )
1314 info->input_signal_events.dsr_up++;
1315 else
1316 info->input_signal_events.dsr_down++;
1317 }
1318 if (status & MISCSTATUS_DCD_LATCHED) {
1319 if ((info->dcd_chkcount)++ >= IO_PIN_SHUTDOWN_LIMIT)
1320 usc_DisablestatusIrqs(info,SICR_DCD);
1321 icount->dcd++;
1322 if (status & MISCSTATUS_DCD) {
1323 info->input_signal_events.dcd_up++;
1324 } else
1325 info->input_signal_events.dcd_down++;
1326#if SYNCLINK_GENERIC_HDLC
1327 if (info->netcount) {
1328 if (status & MISCSTATUS_DCD)
1329 netif_carrier_on(info->netdev);
1330 else
1331 netif_carrier_off(info->netdev);
1332 }
1333#endif
1334 }
1335 if (status & MISCSTATUS_CTS_LATCHED)
1336 {
1337 if ((info->cts_chkcount)++ >= IO_PIN_SHUTDOWN_LIMIT)
1338 usc_DisablestatusIrqs(info,SICR_CTS);
1339 icount->cts++;
1340 if ( status & MISCSTATUS_CTS )
1341 info->input_signal_events.cts_up++;
1342 else
1343 info->input_signal_events.cts_down++;
1344 }
1345 wake_up_interruptible(&info->status_event_wait_q);
1346 wake_up_interruptible(&info->event_wait_q);
1347
1348 if ( (info->port.flags & ASYNC_CHECK_CD) &&
1349 (status & MISCSTATUS_DCD_LATCHED) ) {
1350 if ( debug_level >= DEBUG_LEVEL_ISR )
1351 printk("%s CD now %s...", info->device_name,
1352 (status & MISCSTATUS_DCD) ? "on" : "off");
1353 if (status & MISCSTATUS_DCD)
1354 wake_up_interruptible(&info->port.open_wait);
1355 else {
1356 if ( debug_level >= DEBUG_LEVEL_ISR )
1357 printk("doing serial hangup...");
1358 if (info->port.tty)
1359 tty_hangup(info->port.tty);
1360 }
1361 }
1362
1363 if ( (info->port.flags & ASYNC_CTS_FLOW) &&
1364 (status & MISCSTATUS_CTS_LATCHED) ) {
1365 if (info->port.tty->hw_stopped) {
1366 if (status & MISCSTATUS_CTS) {
1367 if ( debug_level >= DEBUG_LEVEL_ISR )
1368 printk("CTS tx start...");
1369 if (info->port.tty)
1370 info->port.tty->hw_stopped = 0;
1371 usc_start_transmitter(info);
1372 info->pending_bh |= BH_TRANSMIT;
1373 return;
1374 }
1375 } else {
1376 if (!(status & MISCSTATUS_CTS)) {
1377 if ( debug_level >= DEBUG_LEVEL_ISR )
1378 printk("CTS tx stop...");
1379 if (info->port.tty)
1380 info->port.tty->hw_stopped = 1;
1381 usc_stop_transmitter(info);
1382 }
1383 }
1384 }
1385 }
1386
1387 info->pending_bh |= BH_STATUS;
1388
1389 /* for diagnostics set IRQ flag */
1390 if ( status & MISCSTATUS_TXC_LATCHED ){
1391 usc_OutReg( info, SICR,
1392 (unsigned short)(usc_InReg(info,SICR) & ~(SICR_TXC_ACTIVE+SICR_TXC_INACTIVE)) );
1393 usc_UnlatchIostatusBits( info, MISCSTATUS_TXC_LATCHED );
1394 info->irq_occurred = true;
1395 }
1396
1397} /* end of mgsl_isr_io_pin() */
1398
1399/* mgsl_isr_transmit_data()
1400 *
1401 * Service a transmit data interrupt (async mode only).
1402 *
1403 * Arguments: info pointer to device instance data
1404 * Return Value: None
1405 */
1406static void mgsl_isr_transmit_data( struct mgsl_struct *info )
1407{
1408 if ( debug_level >= DEBUG_LEVEL_ISR )
1409 printk("%s(%d):mgsl_isr_transmit_data xmit_cnt=%d\n",
1410 __FILE__,__LINE__,info->xmit_cnt);
1411
1412 usc_ClearIrqPendingBits( info, TRANSMIT_DATA );
1413
1414 if (info->port.tty->stopped || info->port.tty->hw_stopped) {
1415 usc_stop_transmitter(info);
1416 return;
1417 }
1418
1419 if ( info->xmit_cnt )
1420 usc_load_txfifo( info );
1421 else
1422 info->tx_active = false;
1423
1424 if (info->xmit_cnt < WAKEUP_CHARS)
1425 info->pending_bh |= BH_TRANSMIT;
1426
1427} /* end of mgsl_isr_transmit_data() */
1428
1429/* mgsl_isr_receive_data()
1430 *
1431 * Service a receive data interrupt. This occurs
1432 * when operating in asynchronous interrupt transfer mode.
1433 * The receive data FIFO is flushed to the receive data buffers.
1434 *
1435 * Arguments: info pointer to device instance data
1436 * Return Value: None
1437 */
1438static void mgsl_isr_receive_data( struct mgsl_struct *info )
1439{
1440 int Fifocount;
1441 u16 status;
1442 int work = 0;
1443 unsigned char DataByte;
1444 struct tty_struct *tty = info->port.tty;
1445 struct mgsl_icount *icount = &info->icount;
1446
1447 if ( debug_level >= DEBUG_LEVEL_ISR )
1448 printk("%s(%d):mgsl_isr_receive_data\n",
1449 __FILE__,__LINE__);
1450
1451 usc_ClearIrqPendingBits( info, RECEIVE_DATA );
1452
1453 /* select FIFO status for RICR readback */
1454 usc_RCmd( info, RCmd_SelectRicrRxFifostatus );
1455
1456 /* clear the Wordstatus bit so that status readback */
1457 /* only reflects the status of this byte */
1458 usc_OutReg( info, RICR+LSBONLY, (u16)(usc_InReg(info, RICR+LSBONLY) & ~BIT3 ));
1459
1460 /* flush the receive FIFO */
1461
1462 while( (Fifocount = (usc_InReg(info,RICR) >> 8)) ) {
1463 int flag;
1464
1465 /* read one byte from RxFIFO */
1466 outw( (inw(info->io_base + CCAR) & 0x0780) | (RDR+LSBONLY),
1467 info->io_base + CCAR );
1468 DataByte = inb( info->io_base + CCAR );
1469
1470 /* get the status of the received byte */
1471 status = usc_InReg(info, RCSR);
1472 if ( status & (RXSTATUS_FRAMING_ERROR + RXSTATUS_PARITY_ERROR +
1473 RXSTATUS_OVERRUN + RXSTATUS_BREAK_RECEIVED) )
1474 usc_UnlatchRxstatusBits(info,RXSTATUS_ALL);
1475
1476 icount->rx++;
1477
1478 flag = 0;
1479 if ( status & (RXSTATUS_FRAMING_ERROR + RXSTATUS_PARITY_ERROR +
1480 RXSTATUS_OVERRUN + RXSTATUS_BREAK_RECEIVED) ) {
1481 printk("rxerr=%04X\n",status);
1482 /* update error statistics */
1483 if ( status & RXSTATUS_BREAK_RECEIVED ) {
1484 status &= ~(RXSTATUS_FRAMING_ERROR + RXSTATUS_PARITY_ERROR);
1485 icount->brk++;
1486 } else if (status & RXSTATUS_PARITY_ERROR)
1487 icount->parity++;
1488 else if (status & RXSTATUS_FRAMING_ERROR)
1489 icount->frame++;
1490 else if (status & RXSTATUS_OVERRUN) {
1491 /* must issue purge fifo cmd before */
1492 /* 16C32 accepts more receive chars */
1493 usc_RTCmd(info,RTCmd_PurgeRxFifo);
1494 icount->overrun++;
1495 }
1496
1497 /* discard char if tty control flags say so */
1498 if (status & info->ignore_status_mask)
1499 continue;
1500
1501 status &= info->read_status_mask;
1502
1503 if (status & RXSTATUS_BREAK_RECEIVED) {
1504 flag = TTY_BREAK;
1505 if (info->port.flags & ASYNC_SAK)
1506 do_SAK(tty);
1507 } else if (status & RXSTATUS_PARITY_ERROR)
1508 flag = TTY_PARITY;
1509 else if (status & RXSTATUS_FRAMING_ERROR)
1510 flag = TTY_FRAME;
1511 } /* end of if (error) */
1512 tty_insert_flip_char(tty, DataByte, flag);
1513 if (status & RXSTATUS_OVERRUN) {
1514 /* Overrun is special, since it's
1515 * reported immediately, and doesn't
1516 * affect the current character
1517 */
1518 work += tty_insert_flip_char(tty, 0, TTY_OVERRUN);
1519 }
1520 }
1521
1522 if ( debug_level >= DEBUG_LEVEL_ISR ) {
1523 printk("%s(%d):rx=%d brk=%d parity=%d frame=%d overrun=%d\n",
1524 __FILE__,__LINE__,icount->rx,icount->brk,
1525 icount->parity,icount->frame,icount->overrun);
1526 }
1527
1528 if(work)
1529 tty_flip_buffer_push(tty);
1530}
1531
1532/* mgsl_isr_misc()
1533 *
1534 * Service a miscellaneous interrupt source.
1535 *
1536 * Arguments: info pointer to device extension (instance data)
1537 * Return Value: None
1538 */
1539static void mgsl_isr_misc( struct mgsl_struct *info )
1540{
1541 u16 status = usc_InReg( info, MISR );
1542
1543 if ( debug_level >= DEBUG_LEVEL_ISR )
1544 printk("%s(%d):mgsl_isr_misc status=%04X\n",
1545 __FILE__,__LINE__,status);
1546
1547 if ((status & MISCSTATUS_RCC_UNDERRUN) &&
1548 (info->params.mode == MGSL_MODE_HDLC)) {
1549
1550 /* turn off receiver and rx DMA */
1551 usc_EnableReceiver(info,DISABLE_UNCONDITIONAL);
1552 usc_DmaCmd(info, DmaCmd_ResetRxChannel);
1553 usc_UnlatchRxstatusBits(info, RXSTATUS_ALL);
1554 usc_ClearIrqPendingBits(info, RECEIVE_DATA + RECEIVE_STATUS);
1555 usc_DisableInterrupts(info, RECEIVE_DATA + RECEIVE_STATUS);
1556
1557 /* schedule BH handler to restart receiver */
1558 info->pending_bh |= BH_RECEIVE;
1559 info->rx_rcc_underrun = true;
1560 }
1561
1562 usc_ClearIrqPendingBits( info, MISC );
1563 usc_UnlatchMiscstatusBits( info, status );
1564
1565} /* end of mgsl_isr_misc() */
1566
1567/* mgsl_isr_null()
1568 *
1569 * Services undefined interrupt vectors from the
1570 * USC. (hence this function SHOULD never be called)
1571 *
1572 * Arguments: info pointer to device extension (instance data)
1573 * Return Value: None
1574 */
1575static void mgsl_isr_null( struct mgsl_struct *info )
1576{
1577
1578} /* end of mgsl_isr_null() */
1579
1580/* mgsl_isr_receive_dma()
1581 *
1582 * Service a receive DMA channel interrupt.
1583 * For this driver there are two sources of receive DMA interrupts
1584 * as identified in the Receive DMA mode Register (RDMR):
1585 *
1586 * BIT3 EOA/EOL End of List, all receive buffers in receive
1587 * buffer list have been filled (no more free buffers
1588 * available). The DMA controller has shut down.
1589 *
1590 * BIT2 EOB End of Buffer. This interrupt occurs when a receive
1591 * DMA buffer is terminated in response to completion
1592 * of a good frame or a frame with errors. The status
1593 * of the frame is stored in the buffer entry in the
1594 * list of receive buffer entries.
1595 *
1596 * Arguments: info pointer to device instance data
1597 * Return Value: None
1598 */
1599static void mgsl_isr_receive_dma( struct mgsl_struct *info )
1600{
1601 u16 status;
1602
1603 /* clear interrupt pending and IUS bit for Rx DMA IRQ */
1604 usc_OutDmaReg( info, CDIR, BIT9+BIT1 );
1605
1606 /* Read the receive DMA status to identify interrupt type. */
1607 /* This also clears the status bits. */
1608 status = usc_InDmaReg( info, RDMR );
1609
1610 if ( debug_level >= DEBUG_LEVEL_ISR )
1611 printk("%s(%d):mgsl_isr_receive_dma(%s) status=%04X\n",
1612 __FILE__,__LINE__,info->device_name,status);
1613
1614 info->pending_bh |= BH_RECEIVE;
1615
1616 if ( status & BIT3 ) {
1617 info->rx_overflow = true;
1618 info->icount.buf_overrun++;
1619 }
1620
1621} /* end of mgsl_isr_receive_dma() */
1622
1623/* mgsl_isr_transmit_dma()
1624 *
1625 * This function services a transmit DMA channel interrupt.
1626 *
1627 * For this driver there is one source of transmit DMA interrupts
1628 * as identified in the Transmit DMA Mode Register (TDMR):
1629 *
1630 * BIT2 EOB End of Buffer. This interrupt occurs when a
1631 * transmit DMA buffer has been emptied.
1632 *
1633 * The driver maintains enough transmit DMA buffers to hold at least
1634 * one max frame size transmit frame. When operating in a buffered
1635 * transmit mode, there may be enough transmit DMA buffers to hold at
1636 * least two or more max frame size frames. On an EOB condition,
1637 * determine if there are any queued transmit buffers and copy into
1638 * transmit DMA buffers if we have room.
1639 *
1640 * Arguments: info pointer to device instance data
1641 * Return Value: None
1642 */
1643static void mgsl_isr_transmit_dma( struct mgsl_struct *info )
1644{
1645 u16 status;
1646
1647 /* clear interrupt pending and IUS bit for Tx DMA IRQ */
1648 usc_OutDmaReg(info, CDIR, BIT8+BIT0 );
1649
1650 /* Read the transmit DMA status to identify interrupt type. */
1651 /* This also clears the status bits. */
1652
1653 status = usc_InDmaReg( info, TDMR );
1654
1655 if ( debug_level >= DEBUG_LEVEL_ISR )
1656 printk("%s(%d):mgsl_isr_transmit_dma(%s) status=%04X\n",
1657 __FILE__,__LINE__,info->device_name,status);
1658
1659 if ( status & BIT2 ) {
1660 --info->tx_dma_buffers_used;
1661
1662 /* if there are transmit frames queued,
1663 * try to load the next one
1664 */
1665 if ( load_next_tx_holding_buffer(info) ) {
1666 /* if call returns non-zero value, we have
1667 * at least one free tx holding buffer
1668 */
1669 info->pending_bh |= BH_TRANSMIT;
1670 }
1671 }
1672
1673} /* end of mgsl_isr_transmit_dma() */
1674
1675/* mgsl_interrupt()
1676 *
1677 * Interrupt service routine entry point.
1678 *
1679 * Arguments:
1680 *
1681 * irq interrupt number that caused interrupt
1682 * dev_id device ID supplied during interrupt registration
1683 *
1684 * Return Value: None
1685 */
1686static irqreturn_t mgsl_interrupt(int dummy, void *dev_id)
1687{
1688 struct mgsl_struct *info = dev_id;
1689 u16 UscVector;
1690 u16 DmaVector;
1691
1692 if ( debug_level >= DEBUG_LEVEL_ISR )
1693 printk(KERN_DEBUG "%s(%d):mgsl_interrupt(%d)entry.\n",
1694 __FILE__, __LINE__, info->irq_level);
1695
1696 spin_lock(&info->irq_spinlock);
1697
1698 for(;;) {
1699 /* Read the interrupt vectors from hardware. */
1700 UscVector = usc_InReg(info, IVR) >> 9;
1701 DmaVector = usc_InDmaReg(info, DIVR);
1702
1703 if ( debug_level >= DEBUG_LEVEL_ISR )
1704 printk("%s(%d):%s UscVector=%08X DmaVector=%08X\n",
1705 __FILE__,__LINE__,info->device_name,UscVector,DmaVector);
1706
1707 if ( !UscVector && !DmaVector )
1708 break;
1709
1710 /* Dispatch interrupt vector */
1711 if ( UscVector )
1712 (*UscIsrTable[UscVector])(info);
1713 else if ( (DmaVector&(BIT10|BIT9)) == BIT10)
1714 mgsl_isr_transmit_dma(info);
1715 else
1716 mgsl_isr_receive_dma(info);
1717
1718 if ( info->isr_overflow ) {
1719 printk(KERN_ERR "%s(%d):%s isr overflow irq=%d\n",
1720 __FILE__, __LINE__, info->device_name, info->irq_level);
1721 usc_DisableMasterIrqBit(info);
1722 usc_DisableDmaInterrupts(info,DICR_MASTER);
1723 break;
1724 }
1725 }
1726
1727 /* Request bottom half processing if there's something
1728 * for it to do and the bh is not already running
1729 */
1730
1731 if ( info->pending_bh && !info->bh_running && !info->bh_requested ) {
1732 if ( debug_level >= DEBUG_LEVEL_ISR )
1733 printk("%s(%d):%s queueing bh task.\n",
1734 __FILE__,__LINE__,info->device_name);
1735 schedule_work(&info->task);
1736 info->bh_requested = true;
1737 }
1738
1739 spin_unlock(&info->irq_spinlock);
1740
1741 if ( debug_level >= DEBUG_LEVEL_ISR )
1742 printk(KERN_DEBUG "%s(%d):mgsl_interrupt(%d)exit.\n",
1743 __FILE__, __LINE__, info->irq_level);
1744
1745 return IRQ_HANDLED;
1746} /* end of mgsl_interrupt() */
1747
1748/* startup()
1749 *
1750 * Initialize and start device.
1751 *
1752 * Arguments: info pointer to device instance data
1753 * Return Value: 0 if success, otherwise error code
1754 */
1755static int startup(struct mgsl_struct * info)
1756{
1757 int retval = 0;
1758
1759 if ( debug_level >= DEBUG_LEVEL_INFO )
1760 printk("%s(%d):mgsl_startup(%s)\n",__FILE__,__LINE__,info->device_name);
1761
1762 if (info->port.flags & ASYNC_INITIALIZED)
1763 return 0;
1764
1765 if (!info->xmit_buf) {
1766 /* allocate a page of memory for a transmit buffer */
1767 info->xmit_buf = (unsigned char *)get_zeroed_page(GFP_KERNEL);
1768 if (!info->xmit_buf) {
1769 printk(KERN_ERR"%s(%d):%s can't allocate transmit buffer\n",
1770 __FILE__,__LINE__,info->device_name);
1771 return -ENOMEM;
1772 }
1773 }
1774
1775 info->pending_bh = 0;
1776
1777 memset(&info->icount, 0, sizeof(info->icount));
1778
1779 setup_timer(&info->tx_timer, mgsl_tx_timeout, (unsigned long)info);
1780
1781 /* Allocate and claim adapter resources */
1782 retval = mgsl_claim_resources(info);
1783
1784 /* perform existence check and diagnostics */
1785 if ( !retval )
1786 retval = mgsl_adapter_test(info);
1787
1788 if ( retval ) {
1789 if (capable(CAP_SYS_ADMIN) && info->port.tty)
1790 set_bit(TTY_IO_ERROR, &info->port.tty->flags);
1791 mgsl_release_resources(info);
1792 return retval;
1793 }
1794
1795 /* program hardware for current parameters */
1796 mgsl_change_params(info);
1797
1798 if (info->port.tty)
1799 clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
1800
1801 info->port.flags |= ASYNC_INITIALIZED;
1802
1803 return 0;
1804
1805} /* end of startup() */
1806
1807/* shutdown()
1808 *
1809 * Called by mgsl_close() and mgsl_hangup() to shutdown hardware
1810 *
1811 * Arguments: info pointer to device instance data
1812 * Return Value: None
1813 */
1814static void shutdown(struct mgsl_struct * info)
1815{
1816 unsigned long flags;
1817
1818 if (!(info->port.flags & ASYNC_INITIALIZED))
1819 return;
1820
1821 if (debug_level >= DEBUG_LEVEL_INFO)
1822 printk("%s(%d):mgsl_shutdown(%s)\n",
1823 __FILE__,__LINE__, info->device_name );
1824
1825 /* clear status wait queue because status changes */
1826 /* can't happen after shutting down the hardware */
1827 wake_up_interruptible(&info->status_event_wait_q);
1828 wake_up_interruptible(&info->event_wait_q);
1829
1830 del_timer_sync(&info->tx_timer);
1831
1832 if (info->xmit_buf) {
1833 free_page((unsigned long) info->xmit_buf);
1834 info->xmit_buf = NULL;
1835 }
1836
1837 spin_lock_irqsave(&info->irq_spinlock,flags);
1838 usc_DisableMasterIrqBit(info);
1839 usc_stop_receiver(info);
1840 usc_stop_transmitter(info);
1841 usc_DisableInterrupts(info,RECEIVE_DATA + RECEIVE_STATUS +
1842 TRANSMIT_DATA + TRANSMIT_STATUS + IO_PIN + MISC );
1843 usc_DisableDmaInterrupts(info,DICR_MASTER + DICR_TRANSMIT + DICR_RECEIVE);
1844
1845 /* Disable DMAEN (Port 7, Bit 14) */
1846 /* This disconnects the DMA request signal from the ISA bus */
1847 /* on the ISA adapter. This has no effect for the PCI adapter */
1848 usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT15) | BIT14));
1849
1850 /* Disable INTEN (Port 6, Bit12) */
1851 /* This disconnects the IRQ request signal to the ISA bus */
1852 /* on the ISA adapter. This has no effect for the PCI adapter */
1853 usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT13) | BIT12));
1854
1855 if (!info->port.tty || info->port.tty->termios->c_cflag & HUPCL) {
1856 info->serial_signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
1857 usc_set_serial_signals(info);
1858 }
1859
1860 spin_unlock_irqrestore(&info->irq_spinlock,flags);
1861
1862 mgsl_release_resources(info);
1863
1864 if (info->port.tty)
1865 set_bit(TTY_IO_ERROR, &info->port.tty->flags);
1866
1867 info->port.flags &= ~ASYNC_INITIALIZED;
1868
1869} /* end of shutdown() */
1870
1871static void mgsl_program_hw(struct mgsl_struct *info)
1872{
1873 unsigned long flags;
1874
1875 spin_lock_irqsave(&info->irq_spinlock,flags);
1876
1877 usc_stop_receiver(info);
1878 usc_stop_transmitter(info);
1879 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
1880
1881 if (info->params.mode == MGSL_MODE_HDLC ||
1882 info->params.mode == MGSL_MODE_RAW ||
1883 info->netcount)
1884 usc_set_sync_mode(info);
1885 else
1886 usc_set_async_mode(info);
1887
1888 usc_set_serial_signals(info);
1889
1890 info->dcd_chkcount = 0;
1891 info->cts_chkcount = 0;
1892 info->ri_chkcount = 0;
1893 info->dsr_chkcount = 0;
1894
1895 usc_EnableStatusIrqs(info,SICR_CTS+SICR_DSR+SICR_DCD+SICR_RI);
1896 usc_EnableInterrupts(info, IO_PIN);
1897 usc_get_serial_signals(info);
1898
1899 if (info->netcount || info->port.tty->termios->c_cflag & CREAD)
1900 usc_start_receiver(info);
1901
1902 spin_unlock_irqrestore(&info->irq_spinlock,flags);
1903}
1904
1905/* Reconfigure adapter based on new parameters
1906 */
1907static void mgsl_change_params(struct mgsl_struct *info)
1908{
1909 unsigned cflag;
1910 int bits_per_char;
1911
1912 if (!info->port.tty || !info->port.tty->termios)
1913 return;
1914
1915 if (debug_level >= DEBUG_LEVEL_INFO)
1916 printk("%s(%d):mgsl_change_params(%s)\n",
1917 __FILE__,__LINE__, info->device_name );
1918
1919 cflag = info->port.tty->termios->c_cflag;
1920
1921 /* if B0 rate (hangup) specified then negate DTR and RTS */
1922 /* otherwise assert DTR and RTS */
1923 if (cflag & CBAUD)
1924 info->serial_signals |= SerialSignal_RTS + SerialSignal_DTR;
1925 else
1926 info->serial_signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
1927
1928 /* byte size and parity */
1929
1930 switch (cflag & CSIZE) {
1931 case CS5: info->params.data_bits = 5; break;
1932 case CS6: info->params.data_bits = 6; break;
1933 case CS7: info->params.data_bits = 7; break;
1934 case CS8: info->params.data_bits = 8; break;
1935 /* Never happens, but GCC is too dumb to figure it out */
1936 default: info->params.data_bits = 7; break;
1937 }
1938
1939 if (cflag & CSTOPB)
1940 info->params.stop_bits = 2;
1941 else
1942 info->params.stop_bits = 1;
1943
1944 info->params.parity = ASYNC_PARITY_NONE;
1945 if (cflag & PARENB) {
1946 if (cflag & PARODD)
1947 info->params.parity = ASYNC_PARITY_ODD;
1948 else
1949 info->params.parity = ASYNC_PARITY_EVEN;
1950#ifdef CMSPAR
1951 if (cflag & CMSPAR)
1952 info->params.parity = ASYNC_PARITY_SPACE;
1953#endif
1954 }
1955
1956 /* calculate number of jiffies to transmit a full
1957 * FIFO (32 bytes) at specified data rate
1958 */
1959 bits_per_char = info->params.data_bits +
1960 info->params.stop_bits + 1;
1961
1962 /* if port data rate is set to 460800 or less then
1963 * allow tty settings to override, otherwise keep the
1964 * current data rate.
1965 */
1966 if (info->params.data_rate <= 460800)
1967 info->params.data_rate = tty_get_baud_rate(info->port.tty);
1968
1969 if ( info->params.data_rate ) {
1970 info->timeout = (32*HZ*bits_per_char) /
1971 info->params.data_rate;
1972 }
1973 info->timeout += HZ/50; /* Add .02 seconds of slop */
1974
1975 if (cflag & CRTSCTS)
1976 info->port.flags |= ASYNC_CTS_FLOW;
1977 else
1978 info->port.flags &= ~ASYNC_CTS_FLOW;
1979
1980 if (cflag & CLOCAL)
1981 info->port.flags &= ~ASYNC_CHECK_CD;
1982 else
1983 info->port.flags |= ASYNC_CHECK_CD;
1984
1985 /* process tty input control flags */
1986
1987 info->read_status_mask = RXSTATUS_OVERRUN;
1988 if (I_INPCK(info->port.tty))
1989 info->read_status_mask |= RXSTATUS_PARITY_ERROR | RXSTATUS_FRAMING_ERROR;
1990 if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
1991 info->read_status_mask |= RXSTATUS_BREAK_RECEIVED;
1992
1993 if (I_IGNPAR(info->port.tty))
1994 info->ignore_status_mask |= RXSTATUS_PARITY_ERROR | RXSTATUS_FRAMING_ERROR;
1995 if (I_IGNBRK(info->port.tty)) {
1996 info->ignore_status_mask |= RXSTATUS_BREAK_RECEIVED;
1997 /* If ignoring parity and break indicators, ignore
1998 * overruns too. (For real raw support).
1999 */
2000 if (I_IGNPAR(info->port.tty))
2001 info->ignore_status_mask |= RXSTATUS_OVERRUN;
2002 }
2003
2004 mgsl_program_hw(info);
2005
2006} /* end of mgsl_change_params() */
2007
2008/* mgsl_put_char()
2009 *
2010 * Add a character to the transmit buffer.
2011 *
2012 * Arguments: tty pointer to tty information structure
2013 * ch character to add to transmit buffer
2014 *
2015 * Return Value: None
2016 */
2017static int mgsl_put_char(struct tty_struct *tty, unsigned char ch)
2018{
2019 struct mgsl_struct *info = tty->driver_data;
2020 unsigned long flags;
2021 int ret = 0;
2022
2023 if (debug_level >= DEBUG_LEVEL_INFO) {
2024 printk(KERN_DEBUG "%s(%d):mgsl_put_char(%d) on %s\n",
2025 __FILE__, __LINE__, ch, info->device_name);
2026 }
2027
2028 if (mgsl_paranoia_check(info, tty->name, "mgsl_put_char"))
2029 return 0;
2030
2031 if (!info->xmit_buf)
2032 return 0;
2033
2034 spin_lock_irqsave(&info->irq_spinlock, flags);
2035
2036 if ((info->params.mode == MGSL_MODE_ASYNC ) || !info->tx_active) {
2037 if (info->xmit_cnt < SERIAL_XMIT_SIZE - 1) {
2038 info->xmit_buf[info->xmit_head++] = ch;
2039 info->xmit_head &= SERIAL_XMIT_SIZE-1;
2040 info->xmit_cnt++;
2041 ret = 1;
2042 }
2043 }
2044 spin_unlock_irqrestore(&info->irq_spinlock, flags);
2045 return ret;
2046
2047} /* end of mgsl_put_char() */
2048
2049/* mgsl_flush_chars()
2050 *
2051 * Enable transmitter so remaining characters in the
2052 * transmit buffer are sent.
2053 *
2054 * Arguments: tty pointer to tty information structure
2055 * Return Value: None
2056 */
2057static void mgsl_flush_chars(struct tty_struct *tty)
2058{
2059 struct mgsl_struct *info = tty->driver_data;
2060 unsigned long flags;
2061
2062 if ( debug_level >= DEBUG_LEVEL_INFO )
2063 printk( "%s(%d):mgsl_flush_chars() entry on %s xmit_cnt=%d\n",
2064 __FILE__,__LINE__,info->device_name,info->xmit_cnt);
2065
2066 if (mgsl_paranoia_check(info, tty->name, "mgsl_flush_chars"))
2067 return;
2068
2069 if (info->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped ||
2070 !info->xmit_buf)
2071 return;
2072
2073 if ( debug_level >= DEBUG_LEVEL_INFO )
2074 printk( "%s(%d):mgsl_flush_chars() entry on %s starting transmitter\n",
2075 __FILE__,__LINE__,info->device_name );
2076
2077 spin_lock_irqsave(&info->irq_spinlock,flags);
2078
2079 if (!info->tx_active) {
2080 if ( (info->params.mode == MGSL_MODE_HDLC ||
2081 info->params.mode == MGSL_MODE_RAW) && info->xmit_cnt ) {
2082 /* operating in synchronous (frame oriented) mode */
2083 /* copy data from circular xmit_buf to */
2084 /* transmit DMA buffer. */
2085 mgsl_load_tx_dma_buffer(info,
2086 info->xmit_buf,info->xmit_cnt);
2087 }
2088 usc_start_transmitter(info);
2089 }
2090
2091 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2092
2093} /* end of mgsl_flush_chars() */
2094
2095/* mgsl_write()
2096 *
2097 * Send a block of data
2098 *
2099 * Arguments:
2100 *
2101 * tty pointer to tty information structure
2102 * buf pointer to buffer containing send data
2103 * count size of send data in bytes
2104 *
2105 * Return Value: number of characters written
2106 */
2107static int mgsl_write(struct tty_struct * tty,
2108 const unsigned char *buf, int count)
2109{
2110 int c, ret = 0;
2111 struct mgsl_struct *info = tty->driver_data;
2112 unsigned long flags;
2113
2114 if ( debug_level >= DEBUG_LEVEL_INFO )
2115 printk( "%s(%d):mgsl_write(%s) count=%d\n",
2116 __FILE__,__LINE__,info->device_name,count);
2117
2118 if (mgsl_paranoia_check(info, tty->name, "mgsl_write"))
2119 goto cleanup;
2120
2121 if (!info->xmit_buf)
2122 goto cleanup;
2123
2124 if ( info->params.mode == MGSL_MODE_HDLC ||
2125 info->params.mode == MGSL_MODE_RAW ) {
2126 /* operating in synchronous (frame oriented) mode */
2127 /* operating in synchronous (frame oriented) mode */
2128 if (info->tx_active) {
2129
2130 if ( info->params.mode == MGSL_MODE_HDLC ) {
2131 ret = 0;
2132 goto cleanup;
2133 }
2134 /* transmitter is actively sending data -
2135 * if we have multiple transmit dma and
2136 * holding buffers, attempt to queue this
2137 * frame for transmission at a later time.
2138 */
2139 if (info->tx_holding_count >= info->num_tx_holding_buffers ) {
2140 /* no tx holding buffers available */
2141 ret = 0;
2142 goto cleanup;
2143 }
2144
2145 /* queue transmit frame request */
2146 ret = count;
2147 save_tx_buffer_request(info,buf,count);
2148
2149 /* if we have sufficient tx dma buffers,
2150 * load the next buffered tx request
2151 */
2152 spin_lock_irqsave(&info->irq_spinlock,flags);
2153 load_next_tx_holding_buffer(info);
2154 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2155 goto cleanup;
2156 }
2157
2158 /* if operating in HDLC LoopMode and the adapter */
2159 /* has yet to be inserted into the loop, we can't */
2160 /* transmit */
2161
2162 if ( (info->params.flags & HDLC_FLAG_HDLC_LOOPMODE) &&
2163 !usc_loopmode_active(info) )
2164 {
2165 ret = 0;
2166 goto cleanup;
2167 }
2168
2169 if ( info->xmit_cnt ) {
2170 /* Send accumulated from send_char() calls */
2171 /* as frame and wait before accepting more data. */
2172 ret = 0;
2173
2174 /* copy data from circular xmit_buf to */
2175 /* transmit DMA buffer. */
2176 mgsl_load_tx_dma_buffer(info,
2177 info->xmit_buf,info->xmit_cnt);
2178 if ( debug_level >= DEBUG_LEVEL_INFO )
2179 printk( "%s(%d):mgsl_write(%s) sync xmit_cnt flushing\n",
2180 __FILE__,__LINE__,info->device_name);
2181 } else {
2182 if ( debug_level >= DEBUG_LEVEL_INFO )
2183 printk( "%s(%d):mgsl_write(%s) sync transmit accepted\n",
2184 __FILE__,__LINE__,info->device_name);
2185 ret = count;
2186 info->xmit_cnt = count;
2187 mgsl_load_tx_dma_buffer(info,buf,count);
2188 }
2189 } else {
2190 while (1) {
2191 spin_lock_irqsave(&info->irq_spinlock,flags);
2192 c = min_t(int, count,
2193 min(SERIAL_XMIT_SIZE - info->xmit_cnt - 1,
2194 SERIAL_XMIT_SIZE - info->xmit_head));
2195 if (c <= 0) {
2196 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2197 break;
2198 }
2199 memcpy(info->xmit_buf + info->xmit_head, buf, c);
2200 info->xmit_head = ((info->xmit_head + c) &
2201 (SERIAL_XMIT_SIZE-1));
2202 info->xmit_cnt += c;
2203 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2204 buf += c;
2205 count -= c;
2206 ret += c;
2207 }
2208 }
2209
2210 if (info->xmit_cnt && !tty->stopped && !tty->hw_stopped) {
2211 spin_lock_irqsave(&info->irq_spinlock,flags);
2212 if (!info->tx_active)
2213 usc_start_transmitter(info);
2214 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2215 }
2216cleanup:
2217 if ( debug_level >= DEBUG_LEVEL_INFO )
2218 printk( "%s(%d):mgsl_write(%s) returning=%d\n",
2219 __FILE__,__LINE__,info->device_name,ret);
2220
2221 return ret;
2222
2223} /* end of mgsl_write() */
2224
2225/* mgsl_write_room()
2226 *
2227 * Return the count of free bytes in transmit buffer
2228 *
2229 * Arguments: tty pointer to tty info structure
2230 * Return Value: None
2231 */
2232static int mgsl_write_room(struct tty_struct *tty)
2233{
2234 struct mgsl_struct *info = tty->driver_data;
2235 int ret;
2236
2237 if (mgsl_paranoia_check(info, tty->name, "mgsl_write_room"))
2238 return 0;
2239 ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1;
2240 if (ret < 0)
2241 ret = 0;
2242
2243 if (debug_level >= DEBUG_LEVEL_INFO)
2244 printk("%s(%d):mgsl_write_room(%s)=%d\n",
2245 __FILE__,__LINE__, info->device_name,ret );
2246
2247 if ( info->params.mode == MGSL_MODE_HDLC ||
2248 info->params.mode == MGSL_MODE_RAW ) {
2249 /* operating in synchronous (frame oriented) mode */
2250 if ( info->tx_active )
2251 return 0;
2252 else
2253 return HDLC_MAX_FRAME_SIZE;
2254 }
2255
2256 return ret;
2257
2258} /* end of mgsl_write_room() */
2259
2260/* mgsl_chars_in_buffer()
2261 *
2262 * Return the count of bytes in transmit buffer
2263 *
2264 * Arguments: tty pointer to tty info structure
2265 * Return Value: None
2266 */
2267static int mgsl_chars_in_buffer(struct tty_struct *tty)
2268{
2269 struct mgsl_struct *info = tty->driver_data;
2270
2271 if (debug_level >= DEBUG_LEVEL_INFO)
2272 printk("%s(%d):mgsl_chars_in_buffer(%s)\n",
2273 __FILE__,__LINE__, info->device_name );
2274
2275 if (mgsl_paranoia_check(info, tty->name, "mgsl_chars_in_buffer"))
2276 return 0;
2277
2278 if (debug_level >= DEBUG_LEVEL_INFO)
2279 printk("%s(%d):mgsl_chars_in_buffer(%s)=%d\n",
2280 __FILE__,__LINE__, info->device_name,info->xmit_cnt );
2281
2282 if ( info->params.mode == MGSL_MODE_HDLC ||
2283 info->params.mode == MGSL_MODE_RAW ) {
2284 /* operating in synchronous (frame oriented) mode */
2285 if ( info->tx_active )
2286 return info->max_frame_size;
2287 else
2288 return 0;
2289 }
2290
2291 return info->xmit_cnt;
2292} /* end of mgsl_chars_in_buffer() */
2293
2294/* mgsl_flush_buffer()
2295 *
2296 * Discard all data in the send buffer
2297 *
2298 * Arguments: tty pointer to tty info structure
2299 * Return Value: None
2300 */
2301static void mgsl_flush_buffer(struct tty_struct *tty)
2302{
2303 struct mgsl_struct *info = tty->driver_data;
2304 unsigned long flags;
2305
2306 if (debug_level >= DEBUG_LEVEL_INFO)
2307 printk("%s(%d):mgsl_flush_buffer(%s) entry\n",
2308 __FILE__,__LINE__, info->device_name );
2309
2310 if (mgsl_paranoia_check(info, tty->name, "mgsl_flush_buffer"))
2311 return;
2312
2313 spin_lock_irqsave(&info->irq_spinlock,flags);
2314 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
2315 del_timer(&info->tx_timer);
2316 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2317
2318 tty_wakeup(tty);
2319}
2320
2321/* mgsl_send_xchar()
2322 *
2323 * Send a high-priority XON/XOFF character
2324 *
2325 * Arguments: tty pointer to tty info structure
2326 * ch character to send
2327 * Return Value: None
2328 */
2329static void mgsl_send_xchar(struct tty_struct *tty, char ch)
2330{
2331 struct mgsl_struct *info = tty->driver_data;
2332 unsigned long flags;
2333
2334 if (debug_level >= DEBUG_LEVEL_INFO)
2335 printk("%s(%d):mgsl_send_xchar(%s,%d)\n",
2336 __FILE__,__LINE__, info->device_name, ch );
2337
2338 if (mgsl_paranoia_check(info, tty->name, "mgsl_send_xchar"))
2339 return;
2340
2341 info->x_char = ch;
2342 if (ch) {
2343 /* Make sure transmit interrupts are on */
2344 spin_lock_irqsave(&info->irq_spinlock,flags);
2345 if (!info->tx_enabled)
2346 usc_start_transmitter(info);
2347 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2348 }
2349} /* end of mgsl_send_xchar() */
2350
2351/* mgsl_throttle()
2352 *
2353 * Signal remote device to throttle send data (our receive data)
2354 *
2355 * Arguments: tty pointer to tty info structure
2356 * Return Value: None
2357 */
2358static void mgsl_throttle(struct tty_struct * tty)
2359{
2360 struct mgsl_struct *info = tty->driver_data;
2361 unsigned long flags;
2362
2363 if (debug_level >= DEBUG_LEVEL_INFO)
2364 printk("%s(%d):mgsl_throttle(%s) entry\n",
2365 __FILE__,__LINE__, info->device_name );
2366
2367 if (mgsl_paranoia_check(info, tty->name, "mgsl_throttle"))
2368 return;
2369
2370 if (I_IXOFF(tty))
2371 mgsl_send_xchar(tty, STOP_CHAR(tty));
2372
2373 if (tty->termios->c_cflag & CRTSCTS) {
2374 spin_lock_irqsave(&info->irq_spinlock,flags);
2375 info->serial_signals &= ~SerialSignal_RTS;
2376 usc_set_serial_signals(info);
2377 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2378 }
2379} /* end of mgsl_throttle() */
2380
2381/* mgsl_unthrottle()
2382 *
2383 * Signal remote device to stop throttling send data (our receive data)
2384 *
2385 * Arguments: tty pointer to tty info structure
2386 * Return Value: None
2387 */
2388static void mgsl_unthrottle(struct tty_struct * tty)
2389{
2390 struct mgsl_struct *info = tty->driver_data;
2391 unsigned long flags;
2392
2393 if (debug_level >= DEBUG_LEVEL_INFO)
2394 printk("%s(%d):mgsl_unthrottle(%s) entry\n",
2395 __FILE__,__LINE__, info->device_name );
2396
2397 if (mgsl_paranoia_check(info, tty->name, "mgsl_unthrottle"))
2398 return;
2399
2400 if (I_IXOFF(tty)) {
2401 if (info->x_char)
2402 info->x_char = 0;
2403 else
2404 mgsl_send_xchar(tty, START_CHAR(tty));
2405 }
2406
2407 if (tty->termios->c_cflag & CRTSCTS) {
2408 spin_lock_irqsave(&info->irq_spinlock,flags);
2409 info->serial_signals |= SerialSignal_RTS;
2410 usc_set_serial_signals(info);
2411 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2412 }
2413
2414} /* end of mgsl_unthrottle() */
2415
2416/* mgsl_get_stats()
2417 *
2418 * get the current serial parameters information
2419 *
2420 * Arguments: info pointer to device instance data
2421 * user_icount pointer to buffer to hold returned stats
2422 *
2423 * Return Value: 0 if success, otherwise error code
2424 */
2425static int mgsl_get_stats(struct mgsl_struct * info, struct mgsl_icount __user *user_icount)
2426{
2427 int err;
2428
2429 if (debug_level >= DEBUG_LEVEL_INFO)
2430 printk("%s(%d):mgsl_get_params(%s)\n",
2431 __FILE__,__LINE__, info->device_name);
2432
2433 if (!user_icount) {
2434 memset(&info->icount, 0, sizeof(info->icount));
2435 } else {
2436 mutex_lock(&info->port.mutex);
2437 COPY_TO_USER(err, user_icount, &info->icount, sizeof(struct mgsl_icount));
2438 mutex_unlock(&info->port.mutex);
2439 if (err)
2440 return -EFAULT;
2441 }
2442
2443 return 0;
2444
2445} /* end of mgsl_get_stats() */
2446
2447/* mgsl_get_params()
2448 *
2449 * get the current serial parameters information
2450 *
2451 * Arguments: info pointer to device instance data
2452 * user_params pointer to buffer to hold returned params
2453 *
2454 * Return Value: 0 if success, otherwise error code
2455 */
2456static int mgsl_get_params(struct mgsl_struct * info, MGSL_PARAMS __user *user_params)
2457{
2458 int err;
2459 if (debug_level >= DEBUG_LEVEL_INFO)
2460 printk("%s(%d):mgsl_get_params(%s)\n",
2461 __FILE__,__LINE__, info->device_name);
2462
2463 mutex_lock(&info->port.mutex);
2464 COPY_TO_USER(err,user_params, &info->params, sizeof(MGSL_PARAMS));
2465 mutex_unlock(&info->port.mutex);
2466 if (err) {
2467 if ( debug_level >= DEBUG_LEVEL_INFO )
2468 printk( "%s(%d):mgsl_get_params(%s) user buffer copy failed\n",
2469 __FILE__,__LINE__,info->device_name);
2470 return -EFAULT;
2471 }
2472
2473 return 0;
2474
2475} /* end of mgsl_get_params() */
2476
2477/* mgsl_set_params()
2478 *
2479 * set the serial parameters
2480 *
2481 * Arguments:
2482 *
2483 * info pointer to device instance data
2484 * new_params user buffer containing new serial params
2485 *
2486 * Return Value: 0 if success, otherwise error code
2487 */
2488static int mgsl_set_params(struct mgsl_struct * info, MGSL_PARAMS __user *new_params)
2489{
2490 unsigned long flags;
2491 MGSL_PARAMS tmp_params;
2492 int err;
2493
2494 if (debug_level >= DEBUG_LEVEL_INFO)
2495 printk("%s(%d):mgsl_set_params %s\n", __FILE__,__LINE__,
2496 info->device_name );
2497 COPY_FROM_USER(err,&tmp_params, new_params, sizeof(MGSL_PARAMS));
2498 if (err) {
2499 if ( debug_level >= DEBUG_LEVEL_INFO )
2500 printk( "%s(%d):mgsl_set_params(%s) user buffer copy failed\n",
2501 __FILE__,__LINE__,info->device_name);
2502 return -EFAULT;
2503 }
2504
2505 mutex_lock(&info->port.mutex);
2506 spin_lock_irqsave(&info->irq_spinlock,flags);
2507 memcpy(&info->params,&tmp_params,sizeof(MGSL_PARAMS));
2508 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2509
2510 mgsl_change_params(info);
2511 mutex_unlock(&info->port.mutex);
2512
2513 return 0;
2514
2515} /* end of mgsl_set_params() */
2516
2517/* mgsl_get_txidle()
2518 *
2519 * get the current transmit idle mode
2520 *
2521 * Arguments: info pointer to device instance data
2522 * idle_mode pointer to buffer to hold returned idle mode
2523 *
2524 * Return Value: 0 if success, otherwise error code
2525 */
2526static int mgsl_get_txidle(struct mgsl_struct * info, int __user *idle_mode)
2527{
2528 int err;
2529
2530 if (debug_level >= DEBUG_LEVEL_INFO)
2531 printk("%s(%d):mgsl_get_txidle(%s)=%d\n",
2532 __FILE__,__LINE__, info->device_name, info->idle_mode);
2533
2534 COPY_TO_USER(err,idle_mode, &info->idle_mode, sizeof(int));
2535 if (err) {
2536 if ( debug_level >= DEBUG_LEVEL_INFO )
2537 printk( "%s(%d):mgsl_get_txidle(%s) user buffer copy failed\n",
2538 __FILE__,__LINE__,info->device_name);
2539 return -EFAULT;
2540 }
2541
2542 return 0;
2543
2544} /* end of mgsl_get_txidle() */
2545
2546/* mgsl_set_txidle() service ioctl to set transmit idle mode
2547 *
2548 * Arguments: info pointer to device instance data
2549 * idle_mode new idle mode
2550 *
2551 * Return Value: 0 if success, otherwise error code
2552 */
2553static int mgsl_set_txidle(struct mgsl_struct * info, int idle_mode)
2554{
2555 unsigned long flags;
2556
2557 if (debug_level >= DEBUG_LEVEL_INFO)
2558 printk("%s(%d):mgsl_set_txidle(%s,%d)\n", __FILE__,__LINE__,
2559 info->device_name, idle_mode );
2560
2561 spin_lock_irqsave(&info->irq_spinlock,flags);
2562 info->idle_mode = idle_mode;
2563 usc_set_txidle( info );
2564 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2565 return 0;
2566
2567} /* end of mgsl_set_txidle() */
2568
2569/* mgsl_txenable()
2570 *
2571 * enable or disable the transmitter
2572 *
2573 * Arguments:
2574 *
2575 * info pointer to device instance data
2576 * enable 1 = enable, 0 = disable
2577 *
2578 * Return Value: 0 if success, otherwise error code
2579 */
2580static int mgsl_txenable(struct mgsl_struct * info, int enable)
2581{
2582 unsigned long flags;
2583
2584 if (debug_level >= DEBUG_LEVEL_INFO)
2585 printk("%s(%d):mgsl_txenable(%s,%d)\n", __FILE__,__LINE__,
2586 info->device_name, enable);
2587
2588 spin_lock_irqsave(&info->irq_spinlock,flags);
2589 if ( enable ) {
2590 if ( !info->tx_enabled ) {
2591
2592 usc_start_transmitter(info);
2593 /*--------------------------------------------------
2594 * if HDLC/SDLC Loop mode, attempt to insert the
2595 * station in the 'loop' by setting CMR:13. Upon
2596 * receipt of the next GoAhead (RxAbort) sequence,
2597 * the OnLoop indicator (CCSR:7) should go active
2598 * to indicate that we are on the loop
2599 *--------------------------------------------------*/
2600 if ( info->params.flags & HDLC_FLAG_HDLC_LOOPMODE )
2601 usc_loopmode_insert_request( info );
2602 }
2603 } else {
2604 if ( info->tx_enabled )
2605 usc_stop_transmitter(info);
2606 }
2607 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2608 return 0;
2609
2610} /* end of mgsl_txenable() */
2611
2612/* mgsl_txabort() abort send HDLC frame
2613 *
2614 * Arguments: info pointer to device instance data
2615 * Return Value: 0 if success, otherwise error code
2616 */
2617static int mgsl_txabort(struct mgsl_struct * info)
2618{
2619 unsigned long flags;
2620
2621 if (debug_level >= DEBUG_LEVEL_INFO)
2622 printk("%s(%d):mgsl_txabort(%s)\n", __FILE__,__LINE__,
2623 info->device_name);
2624
2625 spin_lock_irqsave(&info->irq_spinlock,flags);
2626 if ( info->tx_active && info->params.mode == MGSL_MODE_HDLC )
2627 {
2628 if ( info->params.flags & HDLC_FLAG_HDLC_LOOPMODE )
2629 usc_loopmode_cancel_transmit( info );
2630 else
2631 usc_TCmd(info,TCmd_SendAbort);
2632 }
2633 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2634 return 0;
2635
2636} /* end of mgsl_txabort() */
2637
2638/* mgsl_rxenable() enable or disable the receiver
2639 *
2640 * Arguments: info pointer to device instance data
2641 * enable 1 = enable, 0 = disable
2642 * Return Value: 0 if success, otherwise error code
2643 */
2644static int mgsl_rxenable(struct mgsl_struct * info, int enable)
2645{
2646 unsigned long flags;
2647
2648 if (debug_level >= DEBUG_LEVEL_INFO)
2649 printk("%s(%d):mgsl_rxenable(%s,%d)\n", __FILE__,__LINE__,
2650 info->device_name, enable);
2651
2652 spin_lock_irqsave(&info->irq_spinlock,flags);
2653 if ( enable ) {
2654 if ( !info->rx_enabled )
2655 usc_start_receiver(info);
2656 } else {
2657 if ( info->rx_enabled )
2658 usc_stop_receiver(info);
2659 }
2660 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2661 return 0;
2662
2663} /* end of mgsl_rxenable() */
2664
2665/* mgsl_wait_event() wait for specified event to occur
2666 *
2667 * Arguments: info pointer to device instance data
2668 * mask pointer to bitmask of events to wait for
2669 * Return Value: 0 if successful and bit mask updated with
2670 * of events triggerred,
2671 * otherwise error code
2672 */
2673static int mgsl_wait_event(struct mgsl_struct * info, int __user * mask_ptr)
2674{
2675 unsigned long flags;
2676 int s;
2677 int rc=0;
2678 struct mgsl_icount cprev, cnow;
2679 int events;
2680 int mask;
2681 struct _input_signal_events oldsigs, newsigs;
2682 DECLARE_WAITQUEUE(wait, current);
2683
2684 COPY_FROM_USER(rc,&mask, mask_ptr, sizeof(int));
2685 if (rc) {
2686 return -EFAULT;
2687 }
2688
2689 if (debug_level >= DEBUG_LEVEL_INFO)
2690 printk("%s(%d):mgsl_wait_event(%s,%d)\n", __FILE__,__LINE__,
2691 info->device_name, mask);
2692
2693 spin_lock_irqsave(&info->irq_spinlock,flags);
2694
2695 /* return immediately if state matches requested events */
2696 usc_get_serial_signals(info);
2697 s = info->serial_signals;
2698 events = mask &
2699 ( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) +
2700 ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) +
2701 ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) +
2702 ((s & SerialSignal_RI) ? MgslEvent_RiActive :MgslEvent_RiInactive) );
2703 if (events) {
2704 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2705 goto exit;
2706 }
2707
2708 /* save current irq counts */
2709 cprev = info->icount;
2710 oldsigs = info->input_signal_events;
2711
2712 /* enable hunt and idle irqs if needed */
2713 if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) {
2714 u16 oldreg = usc_InReg(info,RICR);
2715 u16 newreg = oldreg +
2716 (mask & MgslEvent_ExitHuntMode ? RXSTATUS_EXITED_HUNT:0) +
2717 (mask & MgslEvent_IdleReceived ? RXSTATUS_IDLE_RECEIVED:0);
2718 if (oldreg != newreg)
2719 usc_OutReg(info, RICR, newreg);
2720 }
2721
2722 set_current_state(TASK_INTERRUPTIBLE);
2723 add_wait_queue(&info->event_wait_q, &wait);
2724
2725 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2726
2727
2728 for(;;) {
2729 schedule();
2730 if (signal_pending(current)) {
2731 rc = -ERESTARTSYS;
2732 break;
2733 }
2734
2735 /* get current irq counts */
2736 spin_lock_irqsave(&info->irq_spinlock,flags);
2737 cnow = info->icount;
2738 newsigs = info->input_signal_events;
2739 set_current_state(TASK_INTERRUPTIBLE);
2740 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2741
2742 /* if no change, wait aborted for some reason */
2743 if (newsigs.dsr_up == oldsigs.dsr_up &&
2744 newsigs.dsr_down == oldsigs.dsr_down &&
2745 newsigs.dcd_up == oldsigs.dcd_up &&
2746 newsigs.dcd_down == oldsigs.dcd_down &&
2747 newsigs.cts_up == oldsigs.cts_up &&
2748 newsigs.cts_down == oldsigs.cts_down &&
2749 newsigs.ri_up == oldsigs.ri_up &&
2750 newsigs.ri_down == oldsigs.ri_down &&
2751 cnow.exithunt == cprev.exithunt &&
2752 cnow.rxidle == cprev.rxidle) {
2753 rc = -EIO;
2754 break;
2755 }
2756
2757 events = mask &
2758 ( (newsigs.dsr_up != oldsigs.dsr_up ? MgslEvent_DsrActive:0) +
2759 (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) +
2760 (newsigs.dcd_up != oldsigs.dcd_up ? MgslEvent_DcdActive:0) +
2761 (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) +
2762 (newsigs.cts_up != oldsigs.cts_up ? MgslEvent_CtsActive:0) +
2763 (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) +
2764 (newsigs.ri_up != oldsigs.ri_up ? MgslEvent_RiActive:0) +
2765 (newsigs.ri_down != oldsigs.ri_down ? MgslEvent_RiInactive:0) +
2766 (cnow.exithunt != cprev.exithunt ? MgslEvent_ExitHuntMode:0) +
2767 (cnow.rxidle != cprev.rxidle ? MgslEvent_IdleReceived:0) );
2768 if (events)
2769 break;
2770
2771 cprev = cnow;
2772 oldsigs = newsigs;
2773 }
2774
2775 remove_wait_queue(&info->event_wait_q, &wait);
2776 set_current_state(TASK_RUNNING);
2777
2778 if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) {
2779 spin_lock_irqsave(&info->irq_spinlock,flags);
2780 if (!waitqueue_active(&info->event_wait_q)) {
2781 /* disable enable exit hunt mode/idle rcvd IRQs */
2782 usc_OutReg(info, RICR, usc_InReg(info,RICR) &
2783 ~(RXSTATUS_EXITED_HUNT + RXSTATUS_IDLE_RECEIVED));
2784 }
2785 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2786 }
2787exit:
2788 if ( rc == 0 )
2789 PUT_USER(rc, events, mask_ptr);
2790
2791 return rc;
2792
2793} /* end of mgsl_wait_event() */
2794
2795static int modem_input_wait(struct mgsl_struct *info,int arg)
2796{
2797 unsigned long flags;
2798 int rc;
2799 struct mgsl_icount cprev, cnow;
2800 DECLARE_WAITQUEUE(wait, current);
2801
2802 /* save current irq counts */
2803 spin_lock_irqsave(&info->irq_spinlock,flags);
2804 cprev = info->icount;
2805 add_wait_queue(&info->status_event_wait_q, &wait);
2806 set_current_state(TASK_INTERRUPTIBLE);
2807 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2808
2809 for(;;) {
2810 schedule();
2811 if (signal_pending(current)) {
2812 rc = -ERESTARTSYS;
2813 break;
2814 }
2815
2816 /* get new irq counts */
2817 spin_lock_irqsave(&info->irq_spinlock,flags);
2818 cnow = info->icount;
2819 set_current_state(TASK_INTERRUPTIBLE);
2820 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2821
2822 /* if no change, wait aborted for some reason */
2823 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
2824 cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) {
2825 rc = -EIO;
2826 break;
2827 }
2828
2829 /* check for change in caller specified modem input */
2830 if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) ||
2831 (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) ||
2832 (arg & TIOCM_CD && cnow.dcd != cprev.dcd) ||
2833 (arg & TIOCM_CTS && cnow.cts != cprev.cts)) {
2834 rc = 0;
2835 break;
2836 }
2837
2838 cprev = cnow;
2839 }
2840 remove_wait_queue(&info->status_event_wait_q, &wait);
2841 set_current_state(TASK_RUNNING);
2842 return rc;
2843}
2844
2845/* return the state of the serial control and status signals
2846 */
2847static int tiocmget(struct tty_struct *tty)
2848{
2849 struct mgsl_struct *info = tty->driver_data;
2850 unsigned int result;
2851 unsigned long flags;
2852
2853 spin_lock_irqsave(&info->irq_spinlock,flags);
2854 usc_get_serial_signals(info);
2855 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2856
2857 result = ((info->serial_signals & SerialSignal_RTS) ? TIOCM_RTS:0) +
2858 ((info->serial_signals & SerialSignal_DTR) ? TIOCM_DTR:0) +
2859 ((info->serial_signals & SerialSignal_DCD) ? TIOCM_CAR:0) +
2860 ((info->serial_signals & SerialSignal_RI) ? TIOCM_RNG:0) +
2861 ((info->serial_signals & SerialSignal_DSR) ? TIOCM_DSR:0) +
2862 ((info->serial_signals & SerialSignal_CTS) ? TIOCM_CTS:0);
2863
2864 if (debug_level >= DEBUG_LEVEL_INFO)
2865 printk("%s(%d):%s tiocmget() value=%08X\n",
2866 __FILE__,__LINE__, info->device_name, result );
2867 return result;
2868}
2869
2870/* set modem control signals (DTR/RTS)
2871 */
2872static int tiocmset(struct tty_struct *tty,
2873 unsigned int set, unsigned int clear)
2874{
2875 struct mgsl_struct *info = tty->driver_data;
2876 unsigned long flags;
2877
2878 if (debug_level >= DEBUG_LEVEL_INFO)
2879 printk("%s(%d):%s tiocmset(%x,%x)\n",
2880 __FILE__,__LINE__,info->device_name, set, clear);
2881
2882 if (set & TIOCM_RTS)
2883 info->serial_signals |= SerialSignal_RTS;
2884 if (set & TIOCM_DTR)
2885 info->serial_signals |= SerialSignal_DTR;
2886 if (clear & TIOCM_RTS)
2887 info->serial_signals &= ~SerialSignal_RTS;
2888 if (clear & TIOCM_DTR)
2889 info->serial_signals &= ~SerialSignal_DTR;
2890
2891 spin_lock_irqsave(&info->irq_spinlock,flags);
2892 usc_set_serial_signals(info);
2893 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2894
2895 return 0;
2896}
2897
2898/* mgsl_break() Set or clear transmit break condition
2899 *
2900 * Arguments: tty pointer to tty instance data
2901 * break_state -1=set break condition, 0=clear
2902 * Return Value: error code
2903 */
2904static int mgsl_break(struct tty_struct *tty, int break_state)
2905{
2906 struct mgsl_struct * info = tty->driver_data;
2907 unsigned long flags;
2908
2909 if (debug_level >= DEBUG_LEVEL_INFO)
2910 printk("%s(%d):mgsl_break(%s,%d)\n",
2911 __FILE__,__LINE__, info->device_name, break_state);
2912
2913 if (mgsl_paranoia_check(info, tty->name, "mgsl_break"))
2914 return -EINVAL;
2915
2916 spin_lock_irqsave(&info->irq_spinlock,flags);
2917 if (break_state == -1)
2918 usc_OutReg(info,IOCR,(u16)(usc_InReg(info,IOCR) | BIT7));
2919 else
2920 usc_OutReg(info,IOCR,(u16)(usc_InReg(info,IOCR) & ~BIT7));
2921 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2922 return 0;
2923
2924} /* end of mgsl_break() */
2925
2926/*
2927 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
2928 * Return: write counters to the user passed counter struct
2929 * NB: both 1->0 and 0->1 transitions are counted except for
2930 * RI where only 0->1 is counted.
2931 */
2932static int msgl_get_icount(struct tty_struct *tty,
2933 struct serial_icounter_struct *icount)
2934
2935{
2936 struct mgsl_struct * info = tty->driver_data;
2937 struct mgsl_icount cnow; /* kernel counter temps */
2938 unsigned long flags;
2939
2940 spin_lock_irqsave(&info->irq_spinlock,flags);
2941 cnow = info->icount;
2942 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2943
2944 icount->cts = cnow.cts;
2945 icount->dsr = cnow.dsr;
2946 icount->rng = cnow.rng;
2947 icount->dcd = cnow.dcd;
2948 icount->rx = cnow.rx;
2949 icount->tx = cnow.tx;
2950 icount->frame = cnow.frame;
2951 icount->overrun = cnow.overrun;
2952 icount->parity = cnow.parity;
2953 icount->brk = cnow.brk;
2954 icount->buf_overrun = cnow.buf_overrun;
2955 return 0;
2956}
2957
2958/* mgsl_ioctl() Service an IOCTL request
2959 *
2960 * Arguments:
2961 *
2962 * tty pointer to tty instance data
2963 * cmd IOCTL command code
2964 * arg command argument/context
2965 *
2966 * Return Value: 0 if success, otherwise error code
2967 */
2968static int mgsl_ioctl(struct tty_struct *tty,
2969 unsigned int cmd, unsigned long arg)
2970{
2971 struct mgsl_struct * info = tty->driver_data;
2972
2973 if (debug_level >= DEBUG_LEVEL_INFO)
2974 printk("%s(%d):mgsl_ioctl %s cmd=%08X\n", __FILE__,__LINE__,
2975 info->device_name, cmd );
2976
2977 if (mgsl_paranoia_check(info, tty->name, "mgsl_ioctl"))
2978 return -ENODEV;
2979
2980 if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
2981 (cmd != TIOCMIWAIT)) {
2982 if (tty->flags & (1 << TTY_IO_ERROR))
2983 return -EIO;
2984 }
2985
2986 return mgsl_ioctl_common(info, cmd, arg);
2987}
2988
2989static int mgsl_ioctl_common(struct mgsl_struct *info, unsigned int cmd, unsigned long arg)
2990{
2991 void __user *argp = (void __user *)arg;
2992
2993 switch (cmd) {
2994 case MGSL_IOCGPARAMS:
2995 return mgsl_get_params(info, argp);
2996 case MGSL_IOCSPARAMS:
2997 return mgsl_set_params(info, argp);
2998 case MGSL_IOCGTXIDLE:
2999 return mgsl_get_txidle(info, argp);
3000 case MGSL_IOCSTXIDLE:
3001 return mgsl_set_txidle(info,(int)arg);
3002 case MGSL_IOCTXENABLE:
3003 return mgsl_txenable(info,(int)arg);
3004 case MGSL_IOCRXENABLE:
3005 return mgsl_rxenable(info,(int)arg);
3006 case MGSL_IOCTXABORT:
3007 return mgsl_txabort(info);
3008 case MGSL_IOCGSTATS:
3009 return mgsl_get_stats(info, argp);
3010 case MGSL_IOCWAITEVENT:
3011 return mgsl_wait_event(info, argp);
3012 case MGSL_IOCLOOPTXDONE:
3013 return mgsl_loopmode_send_done(info);
3014 /* Wait for modem input (DCD,RI,DSR,CTS) change
3015 * as specified by mask in arg (TIOCM_RNG/DSR/CD/CTS)
3016 */
3017 case TIOCMIWAIT:
3018 return modem_input_wait(info,(int)arg);
3019
3020 default:
3021 return -ENOIOCTLCMD;
3022 }
3023 return 0;
3024}
3025
3026/* mgsl_set_termios()
3027 *
3028 * Set new termios settings
3029 *
3030 * Arguments:
3031 *
3032 * tty pointer to tty structure
3033 * termios pointer to buffer to hold returned old termios
3034 *
3035 * Return Value: None
3036 */
3037static void mgsl_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
3038{
3039 struct mgsl_struct *info = tty->driver_data;
3040 unsigned long flags;
3041
3042 if (debug_level >= DEBUG_LEVEL_INFO)
3043 printk("%s(%d):mgsl_set_termios %s\n", __FILE__,__LINE__,
3044 tty->driver->name );
3045
3046 mgsl_change_params(info);
3047
3048 /* Handle transition to B0 status */
3049 if (old_termios->c_cflag & CBAUD &&
3050 !(tty->termios->c_cflag & CBAUD)) {
3051 info->serial_signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
3052 spin_lock_irqsave(&info->irq_spinlock,flags);
3053 usc_set_serial_signals(info);
3054 spin_unlock_irqrestore(&info->irq_spinlock,flags);
3055 }
3056
3057 /* Handle transition away from B0 status */
3058 if (!(old_termios->c_cflag & CBAUD) &&
3059 tty->termios->c_cflag & CBAUD) {
3060 info->serial_signals |= SerialSignal_DTR;
3061 if (!(tty->termios->c_cflag & CRTSCTS) ||
3062 !test_bit(TTY_THROTTLED, &tty->flags)) {
3063 info->serial_signals |= SerialSignal_RTS;
3064 }
3065 spin_lock_irqsave(&info->irq_spinlock,flags);
3066 usc_set_serial_signals(info);
3067 spin_unlock_irqrestore(&info->irq_spinlock,flags);
3068 }
3069
3070 /* Handle turning off CRTSCTS */
3071 if (old_termios->c_cflag & CRTSCTS &&
3072 !(tty->termios->c_cflag & CRTSCTS)) {
3073 tty->hw_stopped = 0;
3074 mgsl_start(tty);
3075 }
3076
3077} /* end of mgsl_set_termios() */
3078
3079/* mgsl_close()
3080 *
3081 * Called when port is closed. Wait for remaining data to be
3082 * sent. Disable port and free resources.
3083 *
3084 * Arguments:
3085 *
3086 * tty pointer to open tty structure
3087 * filp pointer to open file object
3088 *
3089 * Return Value: None
3090 */
3091static void mgsl_close(struct tty_struct *tty, struct file * filp)
3092{
3093 struct mgsl_struct * info = tty->driver_data;
3094
3095 if (mgsl_paranoia_check(info, tty->name, "mgsl_close"))
3096 return;
3097
3098 if (debug_level >= DEBUG_LEVEL_INFO)
3099 printk("%s(%d):mgsl_close(%s) entry, count=%d\n",
3100 __FILE__,__LINE__, info->device_name, info->port.count);
3101
3102 if (tty_port_close_start(&info->port, tty, filp) == 0)
3103 goto cleanup;
3104
3105 mutex_lock(&info->port.mutex);
3106 if (info->port.flags & ASYNC_INITIALIZED)
3107 mgsl_wait_until_sent(tty, info->timeout);
3108 mgsl_flush_buffer(tty);
3109 tty_ldisc_flush(tty);
3110 shutdown(info);
3111 mutex_unlock(&info->port.mutex);
3112
3113 tty_port_close_end(&info->port, tty);
3114 info->port.tty = NULL;
3115cleanup:
3116 if (debug_level >= DEBUG_LEVEL_INFO)
3117 printk("%s(%d):mgsl_close(%s) exit, count=%d\n", __FILE__,__LINE__,
3118 tty->driver->name, info->port.count);
3119
3120} /* end of mgsl_close() */
3121
3122/* mgsl_wait_until_sent()
3123 *
3124 * Wait until the transmitter is empty.
3125 *
3126 * Arguments:
3127 *
3128 * tty pointer to tty info structure
3129 * timeout time to wait for send completion
3130 *
3131 * Return Value: None
3132 */
3133static void mgsl_wait_until_sent(struct tty_struct *tty, int timeout)
3134{
3135 struct mgsl_struct * info = tty->driver_data;
3136 unsigned long orig_jiffies, char_time;
3137
3138 if (!info )
3139 return;
3140
3141 if (debug_level >= DEBUG_LEVEL_INFO)
3142 printk("%s(%d):mgsl_wait_until_sent(%s) entry\n",
3143 __FILE__,__LINE__, info->device_name );
3144
3145 if (mgsl_paranoia_check(info, tty->name, "mgsl_wait_until_sent"))
3146 return;
3147
3148 if (!(info->port.flags & ASYNC_INITIALIZED))
3149 goto exit;
3150
3151 orig_jiffies = jiffies;
3152
3153 /* Set check interval to 1/5 of estimated time to
3154 * send a character, and make it at least 1. The check
3155 * interval should also be less than the timeout.
3156 * Note: use tight timings here to satisfy the NIST-PCTS.
3157 */
3158
3159 if ( info->params.data_rate ) {
3160 char_time = info->timeout/(32 * 5);
3161 if (!char_time)
3162 char_time++;
3163 } else
3164 char_time = 1;
3165
3166 if (timeout)
3167 char_time = min_t(unsigned long, char_time, timeout);
3168
3169 if ( info->params.mode == MGSL_MODE_HDLC ||
3170 info->params.mode == MGSL_MODE_RAW ) {
3171 while (info->tx_active) {
3172 msleep_interruptible(jiffies_to_msecs(char_time));
3173 if (signal_pending(current))
3174 break;
3175 if (timeout && time_after(jiffies, orig_jiffies + timeout))
3176 break;
3177 }
3178 } else {
3179 while (!(usc_InReg(info,TCSR) & TXSTATUS_ALL_SENT) &&
3180 info->tx_enabled) {
3181 msleep_interruptible(jiffies_to_msecs(char_time));
3182 if (signal_pending(current))
3183 break;
3184 if (timeout && time_after(jiffies, orig_jiffies + timeout))
3185 break;
3186 }
3187 }
3188
3189exit:
3190 if (debug_level >= DEBUG_LEVEL_INFO)
3191 printk("%s(%d):mgsl_wait_until_sent(%s) exit\n",
3192 __FILE__,__LINE__, info->device_name );
3193
3194} /* end of mgsl_wait_until_sent() */
3195
3196/* mgsl_hangup()
3197 *
3198 * Called by tty_hangup() when a hangup is signaled.
3199 * This is the same as to closing all open files for the port.
3200 *
3201 * Arguments: tty pointer to associated tty object
3202 * Return Value: None
3203 */
3204static void mgsl_hangup(struct tty_struct *tty)
3205{
3206 struct mgsl_struct * info = tty->driver_data;
3207
3208 if (debug_level >= DEBUG_LEVEL_INFO)
3209 printk("%s(%d):mgsl_hangup(%s)\n",
3210 __FILE__,__LINE__, info->device_name );
3211
3212 if (mgsl_paranoia_check(info, tty->name, "mgsl_hangup"))
3213 return;
3214
3215 mgsl_flush_buffer(tty);
3216 shutdown(info);
3217
3218 info->port.count = 0;
3219 info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
3220 info->port.tty = NULL;
3221
3222 wake_up_interruptible(&info->port.open_wait);
3223
3224} /* end of mgsl_hangup() */
3225
3226/*
3227 * carrier_raised()
3228 *
3229 * Return true if carrier is raised
3230 */
3231
3232static int carrier_raised(struct tty_port *port)
3233{
3234 unsigned long flags;
3235 struct mgsl_struct *info = container_of(port, struct mgsl_struct, port);
3236
3237 spin_lock_irqsave(&info->irq_spinlock, flags);
3238 usc_get_serial_signals(info);
3239 spin_unlock_irqrestore(&info->irq_spinlock, flags);
3240 return (info->serial_signals & SerialSignal_DCD) ? 1 : 0;
3241}
3242
3243static void dtr_rts(struct tty_port *port, int on)
3244{
3245 struct mgsl_struct *info = container_of(port, struct mgsl_struct, port);
3246 unsigned long flags;
3247
3248 spin_lock_irqsave(&info->irq_spinlock,flags);
3249 if (on)
3250 info->serial_signals |= SerialSignal_RTS + SerialSignal_DTR;
3251 else
3252 info->serial_signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
3253 usc_set_serial_signals(info);
3254 spin_unlock_irqrestore(&info->irq_spinlock,flags);
3255}
3256
3257
3258/* block_til_ready()
3259 *
3260 * Block the current process until the specified port
3261 * is ready to be opened.
3262 *
3263 * Arguments:
3264 *
3265 * tty pointer to tty info structure
3266 * filp pointer to open file object
3267 * info pointer to device instance data
3268 *
3269 * Return Value: 0 if success, otherwise error code
3270 */
3271static int block_til_ready(struct tty_struct *tty, struct file * filp,
3272 struct mgsl_struct *info)
3273{
3274 DECLARE_WAITQUEUE(wait, current);
3275 int retval;
3276 bool do_clocal = false;
3277 bool extra_count = false;
3278 unsigned long flags;
3279 int dcd;
3280 struct tty_port *port = &info->port;
3281
3282 if (debug_level >= DEBUG_LEVEL_INFO)
3283 printk("%s(%d):block_til_ready on %s\n",
3284 __FILE__,__LINE__, tty->driver->name );
3285
3286 if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
3287 /* nonblock mode is set or port is not enabled */
3288 port->flags |= ASYNC_NORMAL_ACTIVE;
3289 return 0;
3290 }
3291
3292 if (tty->termios->c_cflag & CLOCAL)
3293 do_clocal = true;
3294
3295 /* Wait for carrier detect and the line to become
3296 * free (i.e., not in use by the callout). While we are in
3297 * this loop, port->count is dropped by one, so that
3298 * mgsl_close() knows when to free things. We restore it upon
3299 * exit, either normal or abnormal.
3300 */
3301
3302 retval = 0;
3303 add_wait_queue(&port->open_wait, &wait);
3304
3305 if (debug_level >= DEBUG_LEVEL_INFO)
3306 printk("%s(%d):block_til_ready before block on %s count=%d\n",
3307 __FILE__,__LINE__, tty->driver->name, port->count );
3308
3309 spin_lock_irqsave(&info->irq_spinlock, flags);
3310 if (!tty_hung_up_p(filp)) {
3311 extra_count = true;
3312 port->count--;
3313 }
3314 spin_unlock_irqrestore(&info->irq_spinlock, flags);
3315 port->blocked_open++;
3316
3317 while (1) {
3318 if (tty->termios->c_cflag & CBAUD)
3319 tty_port_raise_dtr_rts(port);
3320
3321 set_current_state(TASK_INTERRUPTIBLE);
3322
3323 if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)){
3324 retval = (port->flags & ASYNC_HUP_NOTIFY) ?
3325 -EAGAIN : -ERESTARTSYS;
3326 break;
3327 }
3328
3329 dcd = tty_port_carrier_raised(&info->port);
3330
3331 if (!(port->flags & ASYNC_CLOSING) && (do_clocal || dcd))
3332 break;
3333
3334 if (signal_pending(current)) {
3335 retval = -ERESTARTSYS;
3336 break;
3337 }
3338
3339 if (debug_level >= DEBUG_LEVEL_INFO)
3340 printk("%s(%d):block_til_ready blocking on %s count=%d\n",
3341 __FILE__,__LINE__, tty->driver->name, port->count );
3342
3343 tty_unlock();
3344 schedule();
3345 tty_lock();
3346 }
3347
3348 set_current_state(TASK_RUNNING);
3349 remove_wait_queue(&port->open_wait, &wait);
3350
3351 /* FIXME: Racy on hangup during close wait */
3352 if (extra_count)
3353 port->count++;
3354 port->blocked_open--;
3355
3356 if (debug_level >= DEBUG_LEVEL_INFO)
3357 printk("%s(%d):block_til_ready after blocking on %s count=%d\n",
3358 __FILE__,__LINE__, tty->driver->name, port->count );
3359
3360 if (!retval)
3361 port->flags |= ASYNC_NORMAL_ACTIVE;
3362
3363 return retval;
3364
3365} /* end of block_til_ready() */
3366
3367/* mgsl_open()
3368 *
3369 * Called when a port is opened. Init and enable port.
3370 * Perform serial-specific initialization for the tty structure.
3371 *
3372 * Arguments: tty pointer to tty info structure
3373 * filp associated file pointer
3374 *
3375 * Return Value: 0 if success, otherwise error code
3376 */
3377static int mgsl_open(struct tty_struct *tty, struct file * filp)
3378{
3379 struct mgsl_struct *info;
3380 int retval, line;
3381 unsigned long flags;
3382
3383 /* verify range of specified line number */
3384 line = tty->index;
3385 if ((line < 0) || (line >= mgsl_device_count)) {
3386 printk("%s(%d):mgsl_open with invalid line #%d.\n",
3387 __FILE__,__LINE__,line);
3388 return -ENODEV;
3389 }
3390
3391 /* find the info structure for the specified line */
3392 info = mgsl_device_list;
3393 while(info && info->line != line)
3394 info = info->next_device;
3395 if (mgsl_paranoia_check(info, tty->name, "mgsl_open"))
3396 return -ENODEV;
3397
3398 tty->driver_data = info;
3399 info->port.tty = tty;
3400
3401 if (debug_level >= DEBUG_LEVEL_INFO)
3402 printk("%s(%d):mgsl_open(%s), old ref count = %d\n",
3403 __FILE__,__LINE__,tty->driver->name, info->port.count);
3404
3405 /* If port is closing, signal caller to try again */
3406 if (tty_hung_up_p(filp) || info->port.flags & ASYNC_CLOSING){
3407 if (info->port.flags & ASYNC_CLOSING)
3408 interruptible_sleep_on(&info->port.close_wait);
3409 retval = ((info->port.flags & ASYNC_HUP_NOTIFY) ?
3410 -EAGAIN : -ERESTARTSYS);
3411 goto cleanup;
3412 }
3413
3414 info->port.tty->low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
3415
3416 spin_lock_irqsave(&info->netlock, flags);
3417 if (info->netcount) {
3418 retval = -EBUSY;
3419 spin_unlock_irqrestore(&info->netlock, flags);
3420 goto cleanup;
3421 }
3422 info->port.count++;
3423 spin_unlock_irqrestore(&info->netlock, flags);
3424
3425 if (info->port.count == 1) {
3426 /* 1st open on this device, init hardware */
3427 retval = startup(info);
3428 if (retval < 0)
3429 goto cleanup;
3430 }
3431
3432 retval = block_til_ready(tty, filp, info);
3433 if (retval) {
3434 if (debug_level >= DEBUG_LEVEL_INFO)
3435 printk("%s(%d):block_til_ready(%s) returned %d\n",
3436 __FILE__,__LINE__, info->device_name, retval);
3437 goto cleanup;
3438 }
3439
3440 if (debug_level >= DEBUG_LEVEL_INFO)
3441 printk("%s(%d):mgsl_open(%s) success\n",
3442 __FILE__,__LINE__, info->device_name);
3443 retval = 0;
3444
3445cleanup:
3446 if (retval) {
3447 if (tty->count == 1)
3448 info->port.tty = NULL; /* tty layer will release tty struct */
3449 if(info->port.count)
3450 info->port.count--;
3451 }
3452
3453 return retval;
3454
3455} /* end of mgsl_open() */
3456
3457/*
3458 * /proc fs routines....
3459 */
3460
3461static inline void line_info(struct seq_file *m, struct mgsl_struct *info)
3462{
3463 char stat_buf[30];
3464 unsigned long flags;
3465
3466 if (info->bus_type == MGSL_BUS_TYPE_PCI) {
3467 seq_printf(m, "%s:PCI io:%04X irq:%d mem:%08X lcr:%08X",
3468 info->device_name, info->io_base, info->irq_level,
3469 info->phys_memory_base, info->phys_lcr_base);
3470 } else {
3471 seq_printf(m, "%s:(E)ISA io:%04X irq:%d dma:%d",
3472 info->device_name, info->io_base,
3473 info->irq_level, info->dma_level);
3474 }
3475
3476 /* output current serial signal states */
3477 spin_lock_irqsave(&info->irq_spinlock,flags);
3478 usc_get_serial_signals(info);
3479 spin_unlock_irqrestore(&info->irq_spinlock,flags);
3480
3481 stat_buf[0] = 0;
3482 stat_buf[1] = 0;
3483 if (info->serial_signals & SerialSignal_RTS)
3484 strcat(stat_buf, "|RTS");
3485 if (info->serial_signals & SerialSignal_CTS)
3486 strcat(stat_buf, "|CTS");
3487 if (info->serial_signals & SerialSignal_DTR)
3488 strcat(stat_buf, "|DTR");
3489 if (info->serial_signals & SerialSignal_DSR)
3490 strcat(stat_buf, "|DSR");
3491 if (info->serial_signals & SerialSignal_DCD)
3492 strcat(stat_buf, "|CD");
3493 if (info->serial_signals & SerialSignal_RI)
3494 strcat(stat_buf, "|RI");
3495
3496 if (info->params.mode == MGSL_MODE_HDLC ||
3497 info->params.mode == MGSL_MODE_RAW ) {
3498 seq_printf(m, " HDLC txok:%d rxok:%d",
3499 info->icount.txok, info->icount.rxok);
3500 if (info->icount.txunder)
3501 seq_printf(m, " txunder:%d", info->icount.txunder);
3502 if (info->icount.txabort)
3503 seq_printf(m, " txabort:%d", info->icount.txabort);
3504 if (info->icount.rxshort)
3505 seq_printf(m, " rxshort:%d", info->icount.rxshort);
3506 if (info->icount.rxlong)
3507 seq_printf(m, " rxlong:%d", info->icount.rxlong);
3508 if (info->icount.rxover)
3509 seq_printf(m, " rxover:%d", info->icount.rxover);
3510 if (info->icount.rxcrc)
3511 seq_printf(m, " rxcrc:%d", info->icount.rxcrc);
3512 } else {
3513 seq_printf(m, " ASYNC tx:%d rx:%d",
3514 info->icount.tx, info->icount.rx);
3515 if (info->icount.frame)
3516 seq_printf(m, " fe:%d", info->icount.frame);
3517 if (info->icount.parity)
3518 seq_printf(m, " pe:%d", info->icount.parity);
3519 if (info->icount.brk)
3520 seq_printf(m, " brk:%d", info->icount.brk);
3521 if (info->icount.overrun)
3522 seq_printf(m, " oe:%d", info->icount.overrun);
3523 }
3524
3525 /* Append serial signal status to end */
3526 seq_printf(m, " %s\n", stat_buf+1);
3527
3528 seq_printf(m, "txactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
3529 info->tx_active,info->bh_requested,info->bh_running,
3530 info->pending_bh);
3531
3532 spin_lock_irqsave(&info->irq_spinlock,flags);
3533 {
3534 u16 Tcsr = usc_InReg( info, TCSR );
3535 u16 Tdmr = usc_InDmaReg( info, TDMR );
3536 u16 Ticr = usc_InReg( info, TICR );
3537 u16 Rscr = usc_InReg( info, RCSR );
3538 u16 Rdmr = usc_InDmaReg( info, RDMR );
3539 u16 Ricr = usc_InReg( info, RICR );
3540 u16 Icr = usc_InReg( info, ICR );
3541 u16 Dccr = usc_InReg( info, DCCR );
3542 u16 Tmr = usc_InReg( info, TMR );
3543 u16 Tccr = usc_InReg( info, TCCR );
3544 u16 Ccar = inw( info->io_base + CCAR );
3545 seq_printf(m, "tcsr=%04X tdmr=%04X ticr=%04X rcsr=%04X rdmr=%04X\n"
3546 "ricr=%04X icr =%04X dccr=%04X tmr=%04X tccr=%04X ccar=%04X\n",
3547 Tcsr,Tdmr,Ticr,Rscr,Rdmr,Ricr,Icr,Dccr,Tmr,Tccr,Ccar );
3548 }
3549 spin_unlock_irqrestore(&info->irq_spinlock,flags);
3550}
3551
3552/* Called to print information about devices */
3553static int mgsl_proc_show(struct seq_file *m, void *v)
3554{
3555 struct mgsl_struct *info;
3556
3557 seq_printf(m, "synclink driver:%s\n", driver_version);
3558
3559 info = mgsl_device_list;
3560 while( info ) {
3561 line_info(m, info);
3562 info = info->next_device;
3563 }
3564 return 0;
3565}
3566
3567static int mgsl_proc_open(struct inode *inode, struct file *file)
3568{
3569 return single_open(file, mgsl_proc_show, NULL);
3570}
3571
3572static const struct file_operations mgsl_proc_fops = {
3573 .owner = THIS_MODULE,
3574 .open = mgsl_proc_open,
3575 .read = seq_read,
3576 .llseek = seq_lseek,
3577 .release = single_release,
3578};
3579
3580/* mgsl_allocate_dma_buffers()
3581 *
3582 * Allocate and format DMA buffers (ISA adapter)
3583 * or format shared memory buffers (PCI adapter).
3584 *
3585 * Arguments: info pointer to device instance data
3586 * Return Value: 0 if success, otherwise error
3587 */
3588static int mgsl_allocate_dma_buffers(struct mgsl_struct *info)
3589{
3590 unsigned short BuffersPerFrame;
3591
3592 info->last_mem_alloc = 0;
3593
3594 /* Calculate the number of DMA buffers necessary to hold the */
3595 /* largest allowable frame size. Note: If the max frame size is */
3596 /* not an even multiple of the DMA buffer size then we need to */
3597 /* round the buffer count per frame up one. */
3598
3599 BuffersPerFrame = (unsigned short)(info->max_frame_size/DMABUFFERSIZE);
3600 if ( info->max_frame_size % DMABUFFERSIZE )
3601 BuffersPerFrame++;
3602
3603 if ( info->bus_type == MGSL_BUS_TYPE_PCI ) {
3604 /*
3605 * The PCI adapter has 256KBytes of shared memory to use.
3606 * This is 64 PAGE_SIZE buffers.
3607 *
3608 * The first page is used for padding at this time so the
3609 * buffer list does not begin at offset 0 of the PCI
3610 * adapter's shared memory.
3611 *
3612 * The 2nd page is used for the buffer list. A 4K buffer
3613 * list can hold 128 DMA_BUFFER structures at 32 bytes
3614 * each.
3615 *
3616 * This leaves 62 4K pages.
3617 *
3618 * The next N pages are used for transmit frame(s). We
3619 * reserve enough 4K page blocks to hold the required
3620 * number of transmit dma buffers (num_tx_dma_buffers),
3621 * each of MaxFrameSize size.
3622 *
3623 * Of the remaining pages (62-N), determine how many can
3624 * be used to receive full MaxFrameSize inbound frames
3625 */
3626 info->tx_buffer_count = info->num_tx_dma_buffers * BuffersPerFrame;
3627 info->rx_buffer_count = 62 - info->tx_buffer_count;
3628 } else {
3629 /* Calculate the number of PAGE_SIZE buffers needed for */
3630 /* receive and transmit DMA buffers. */
3631
3632
3633 /* Calculate the number of DMA buffers necessary to */
3634 /* hold 7 max size receive frames and one max size transmit frame. */
3635 /* The receive buffer count is bumped by one so we avoid an */
3636 /* End of List condition if all receive buffers are used when */
3637 /* using linked list DMA buffers. */
3638
3639 info->tx_buffer_count = info->num_tx_dma_buffers * BuffersPerFrame;
3640 info->rx_buffer_count = (BuffersPerFrame * MAXRXFRAMES) + 6;
3641
3642 /*
3643 * limit total TxBuffers & RxBuffers to 62 4K total
3644 * (ala PCI Allocation)
3645 */
3646
3647 if ( (info->tx_buffer_count + info->rx_buffer_count) > 62 )
3648 info->rx_buffer_count = 62 - info->tx_buffer_count;
3649
3650 }
3651
3652 if ( debug_level >= DEBUG_LEVEL_INFO )
3653 printk("%s(%d):Allocating %d TX and %d RX DMA buffers.\n",
3654 __FILE__,__LINE__, info->tx_buffer_count,info->rx_buffer_count);
3655
3656 if ( mgsl_alloc_buffer_list_memory( info ) < 0 ||
3657 mgsl_alloc_frame_memory(info, info->rx_buffer_list, info->rx_buffer_count) < 0 ||
3658 mgsl_alloc_frame_memory(info, info->tx_buffer_list, info->tx_buffer_count) < 0 ||
3659 mgsl_alloc_intermediate_rxbuffer_memory(info) < 0 ||
3660 mgsl_alloc_intermediate_txbuffer_memory(info) < 0 ) {
3661 printk("%s(%d):Can't allocate DMA buffer memory\n",__FILE__,__LINE__);
3662 return -ENOMEM;
3663 }
3664
3665 mgsl_reset_rx_dma_buffers( info );
3666 mgsl_reset_tx_dma_buffers( info );
3667
3668 return 0;
3669
3670} /* end of mgsl_allocate_dma_buffers() */
3671
3672/*
3673 * mgsl_alloc_buffer_list_memory()
3674 *
3675 * Allocate a common DMA buffer for use as the
3676 * receive and transmit buffer lists.
3677 *
3678 * A buffer list is a set of buffer entries where each entry contains
3679 * a pointer to an actual buffer and a pointer to the next buffer entry
3680 * (plus some other info about the buffer).
3681 *
3682 * The buffer entries for a list are built to form a circular list so
3683 * that when the entire list has been traversed you start back at the
3684 * beginning.
3685 *
3686 * This function allocates memory for just the buffer entries.
3687 * The links (pointer to next entry) are filled in with the physical
3688 * address of the next entry so the adapter can navigate the list
3689 * using bus master DMA. The pointers to the actual buffers are filled
3690 * out later when the actual buffers are allocated.
3691 *
3692 * Arguments: info pointer to device instance data
3693 * Return Value: 0 if success, otherwise error
3694 */
3695static int mgsl_alloc_buffer_list_memory( struct mgsl_struct *info )
3696{
3697 unsigned int i;
3698
3699 if ( info->bus_type == MGSL_BUS_TYPE_PCI ) {
3700 /* PCI adapter uses shared memory. */
3701 info->buffer_list = info->memory_base + info->last_mem_alloc;
3702 info->buffer_list_phys = info->last_mem_alloc;
3703 info->last_mem_alloc += BUFFERLISTSIZE;
3704 } else {
3705 /* ISA adapter uses system memory. */
3706 /* The buffer lists are allocated as a common buffer that both */
3707 /* the processor and adapter can access. This allows the driver to */
3708 /* inspect portions of the buffer while other portions are being */
3709 /* updated by the adapter using Bus Master DMA. */
3710
3711 info->buffer_list = dma_alloc_coherent(NULL, BUFFERLISTSIZE, &info->buffer_list_dma_addr, GFP_KERNEL);
3712 if (info->buffer_list == NULL)
3713 return -ENOMEM;
3714 info->buffer_list_phys = (u32)(info->buffer_list_dma_addr);
3715 }
3716
3717 /* We got the memory for the buffer entry lists. */
3718 /* Initialize the memory block to all zeros. */
3719 memset( info->buffer_list, 0, BUFFERLISTSIZE );
3720
3721 /* Save virtual address pointers to the receive and */
3722 /* transmit buffer lists. (Receive 1st). These pointers will */
3723 /* be used by the processor to access the lists. */
3724 info->rx_buffer_list = (DMABUFFERENTRY *)info->buffer_list;
3725 info->tx_buffer_list = (DMABUFFERENTRY *)info->buffer_list;
3726 info->tx_buffer_list += info->rx_buffer_count;
3727
3728 /*
3729 * Build the links for the buffer entry lists such that
3730 * two circular lists are built. (Transmit and Receive).
3731 *
3732 * Note: the links are physical addresses
3733 * which are read by the adapter to determine the next
3734 * buffer entry to use.
3735 */
3736
3737 for ( i = 0; i < info->rx_buffer_count; i++ ) {
3738 /* calculate and store physical address of this buffer entry */
3739 info->rx_buffer_list[i].phys_entry =
3740 info->buffer_list_phys + (i * sizeof(DMABUFFERENTRY));
3741
3742 /* calculate and store physical address of */
3743 /* next entry in cirular list of entries */
3744
3745 info->rx_buffer_list[i].link = info->buffer_list_phys;
3746
3747 if ( i < info->rx_buffer_count - 1 )
3748 info->rx_buffer_list[i].link += (i + 1) * sizeof(DMABUFFERENTRY);
3749 }
3750
3751 for ( i = 0; i < info->tx_buffer_count; i++ ) {
3752 /* calculate and store physical address of this buffer entry */
3753 info->tx_buffer_list[i].phys_entry = info->buffer_list_phys +
3754 ((info->rx_buffer_count + i) * sizeof(DMABUFFERENTRY));
3755
3756 /* calculate and store physical address of */
3757 /* next entry in cirular list of entries */
3758
3759 info->tx_buffer_list[i].link = info->buffer_list_phys +
3760 info->rx_buffer_count * sizeof(DMABUFFERENTRY);
3761
3762 if ( i < info->tx_buffer_count - 1 )
3763 info->tx_buffer_list[i].link += (i + 1) * sizeof(DMABUFFERENTRY);
3764 }
3765
3766 return 0;
3767
3768} /* end of mgsl_alloc_buffer_list_memory() */
3769
3770/* Free DMA buffers allocated for use as the
3771 * receive and transmit buffer lists.
3772 * Warning:
3773 *
3774 * The data transfer buffers associated with the buffer list
3775 * MUST be freed before freeing the buffer list itself because
3776 * the buffer list contains the information necessary to free
3777 * the individual buffers!
3778 */
3779static void mgsl_free_buffer_list_memory( struct mgsl_struct *info )
3780{
3781 if (info->buffer_list && info->bus_type != MGSL_BUS_TYPE_PCI)
3782 dma_free_coherent(NULL, BUFFERLISTSIZE, info->buffer_list, info->buffer_list_dma_addr);
3783
3784 info->buffer_list = NULL;
3785 info->rx_buffer_list = NULL;
3786 info->tx_buffer_list = NULL;
3787
3788} /* end of mgsl_free_buffer_list_memory() */
3789
3790/*
3791 * mgsl_alloc_frame_memory()
3792 *
3793 * Allocate the frame DMA buffers used by the specified buffer list.
3794 * Each DMA buffer will be one memory page in size. This is necessary
3795 * because memory can fragment enough that it may be impossible
3796 * contiguous pages.
3797 *
3798 * Arguments:
3799 *
3800 * info pointer to device instance data
3801 * BufferList pointer to list of buffer entries
3802 * Buffercount count of buffer entries in buffer list
3803 *
3804 * Return Value: 0 if success, otherwise -ENOMEM
3805 */
3806static int mgsl_alloc_frame_memory(struct mgsl_struct *info,DMABUFFERENTRY *BufferList,int Buffercount)
3807{
3808 int i;
3809 u32 phys_addr;
3810
3811 /* Allocate page sized buffers for the receive buffer list */
3812
3813 for ( i = 0; i < Buffercount; i++ ) {
3814 if ( info->bus_type == MGSL_BUS_TYPE_PCI ) {
3815 /* PCI adapter uses shared memory buffers. */
3816 BufferList[i].virt_addr = info->memory_base + info->last_mem_alloc;
3817 phys_addr = info->last_mem_alloc;
3818 info->last_mem_alloc += DMABUFFERSIZE;
3819 } else {
3820 /* ISA adapter uses system memory. */
3821 BufferList[i].virt_addr = dma_alloc_coherent(NULL, DMABUFFERSIZE, &BufferList[i].dma_addr, GFP_KERNEL);
3822 if (BufferList[i].virt_addr == NULL)
3823 return -ENOMEM;
3824 phys_addr = (u32)(BufferList[i].dma_addr);
3825 }
3826 BufferList[i].phys_addr = phys_addr;
3827 }
3828
3829 return 0;
3830
3831} /* end of mgsl_alloc_frame_memory() */
3832
3833/*
3834 * mgsl_free_frame_memory()
3835 *
3836 * Free the buffers associated with
3837 * each buffer entry of a buffer list.
3838 *
3839 * Arguments:
3840 *
3841 * info pointer to device instance data
3842 * BufferList pointer to list of buffer entries
3843 * Buffercount count of buffer entries in buffer list
3844 *
3845 * Return Value: None
3846 */
3847static void mgsl_free_frame_memory(struct mgsl_struct *info, DMABUFFERENTRY *BufferList, int Buffercount)
3848{
3849 int i;
3850
3851 if ( BufferList ) {
3852 for ( i = 0 ; i < Buffercount ; i++ ) {
3853 if ( BufferList[i].virt_addr ) {
3854 if ( info->bus_type != MGSL_BUS_TYPE_PCI )
3855 dma_free_coherent(NULL, DMABUFFERSIZE, BufferList[i].virt_addr, BufferList[i].dma_addr);
3856 BufferList[i].virt_addr = NULL;
3857 }
3858 }
3859 }
3860
3861} /* end of mgsl_free_frame_memory() */
3862
3863/* mgsl_free_dma_buffers()
3864 *
3865 * Free DMA buffers
3866 *
3867 * Arguments: info pointer to device instance data
3868 * Return Value: None
3869 */
3870static void mgsl_free_dma_buffers( struct mgsl_struct *info )
3871{
3872 mgsl_free_frame_memory( info, info->rx_buffer_list, info->rx_buffer_count );
3873 mgsl_free_frame_memory( info, info->tx_buffer_list, info->tx_buffer_count );
3874 mgsl_free_buffer_list_memory( info );
3875
3876} /* end of mgsl_free_dma_buffers() */
3877
3878
3879/*
3880 * mgsl_alloc_intermediate_rxbuffer_memory()
3881 *
3882 * Allocate a buffer large enough to hold max_frame_size. This buffer
3883 * is used to pass an assembled frame to the line discipline.
3884 *
3885 * Arguments:
3886 *
3887 * info pointer to device instance data
3888 *
3889 * Return Value: 0 if success, otherwise -ENOMEM
3890 */
3891static int mgsl_alloc_intermediate_rxbuffer_memory(struct mgsl_struct *info)
3892{
3893 info->intermediate_rxbuffer = kmalloc(info->max_frame_size, GFP_KERNEL | GFP_DMA);
3894 if ( info->intermediate_rxbuffer == NULL )
3895 return -ENOMEM;
3896
3897 return 0;
3898
3899} /* end of mgsl_alloc_intermediate_rxbuffer_memory() */
3900
3901/*
3902 * mgsl_free_intermediate_rxbuffer_memory()
3903 *
3904 *
3905 * Arguments:
3906 *
3907 * info pointer to device instance data
3908 *
3909 * Return Value: None
3910 */
3911static void mgsl_free_intermediate_rxbuffer_memory(struct mgsl_struct *info)
3912{
3913 kfree(info->intermediate_rxbuffer);
3914 info->intermediate_rxbuffer = NULL;
3915
3916} /* end of mgsl_free_intermediate_rxbuffer_memory() */
3917
3918/*
3919 * mgsl_alloc_intermediate_txbuffer_memory()
3920 *
3921 * Allocate intermdiate transmit buffer(s) large enough to hold max_frame_size.
3922 * This buffer is used to load transmit frames into the adapter's dma transfer
3923 * buffers when there is sufficient space.
3924 *
3925 * Arguments:
3926 *
3927 * info pointer to device instance data
3928 *
3929 * Return Value: 0 if success, otherwise -ENOMEM
3930 */
3931static int mgsl_alloc_intermediate_txbuffer_memory(struct mgsl_struct *info)
3932{
3933 int i;
3934
3935 if ( debug_level >= DEBUG_LEVEL_INFO )
3936 printk("%s %s(%d) allocating %d tx holding buffers\n",
3937 info->device_name, __FILE__,__LINE__,info->num_tx_holding_buffers);
3938
3939 memset(info->tx_holding_buffers,0,sizeof(info->tx_holding_buffers));
3940
3941 for ( i=0; i<info->num_tx_holding_buffers; ++i) {
3942 info->tx_holding_buffers[i].buffer =
3943 kmalloc(info->max_frame_size, GFP_KERNEL);
3944 if (info->tx_holding_buffers[i].buffer == NULL) {
3945 for (--i; i >= 0; i--) {
3946 kfree(info->tx_holding_buffers[i].buffer);
3947 info->tx_holding_buffers[i].buffer = NULL;
3948 }
3949 return -ENOMEM;
3950 }
3951 }
3952
3953 return 0;
3954
3955} /* end of mgsl_alloc_intermediate_txbuffer_memory() */
3956
3957/*
3958 * mgsl_free_intermediate_txbuffer_memory()
3959 *
3960 *
3961 * Arguments:
3962 *
3963 * info pointer to device instance data
3964 *
3965 * Return Value: None
3966 */
3967static void mgsl_free_intermediate_txbuffer_memory(struct mgsl_struct *info)
3968{
3969 int i;
3970
3971 for ( i=0; i<info->num_tx_holding_buffers; ++i ) {
3972 kfree(info->tx_holding_buffers[i].buffer);
3973 info->tx_holding_buffers[i].buffer = NULL;
3974 }
3975
3976 info->get_tx_holding_index = 0;
3977 info->put_tx_holding_index = 0;
3978 info->tx_holding_count = 0;
3979
3980} /* end of mgsl_free_intermediate_txbuffer_memory() */
3981
3982
3983/*
3984 * load_next_tx_holding_buffer()
3985 *
3986 * attempts to load the next buffered tx request into the
3987 * tx dma buffers
3988 *
3989 * Arguments:
3990 *
3991 * info pointer to device instance data
3992 *
3993 * Return Value: true if next buffered tx request loaded
3994 * into adapter's tx dma buffer,
3995 * false otherwise
3996 */
3997static bool load_next_tx_holding_buffer(struct mgsl_struct *info)
3998{
3999 bool ret = false;
4000
4001 if ( info->tx_holding_count ) {
4002 /* determine if we have enough tx dma buffers
4003 * to accommodate the next tx frame
4004 */
4005 struct tx_holding_buffer *ptx =
4006 &info->tx_holding_buffers[info->get_tx_holding_index];
4007 int num_free = num_free_tx_dma_buffers(info);
4008 int num_needed = ptx->buffer_size / DMABUFFERSIZE;
4009 if ( ptx->buffer_size % DMABUFFERSIZE )
4010 ++num_needed;
4011
4012 if (num_needed <= num_free) {
4013 info->xmit_cnt = ptx->buffer_size;
4014 mgsl_load_tx_dma_buffer(info,ptx->buffer,ptx->buffer_size);
4015
4016 --info->tx_holding_count;
4017 if ( ++info->get_tx_holding_index >= info->num_tx_holding_buffers)
4018 info->get_tx_holding_index=0;
4019
4020 /* restart transmit timer */
4021 mod_timer(&info->tx_timer, jiffies + msecs_to_jiffies(5000));
4022
4023 ret = true;
4024 }
4025 }
4026
4027 return ret;
4028}
4029
4030/*
4031 * save_tx_buffer_request()
4032 *
4033 * attempt to store transmit frame request for later transmission
4034 *
4035 * Arguments:
4036 *
4037 * info pointer to device instance data
4038 * Buffer pointer to buffer containing frame to load
4039 * BufferSize size in bytes of frame in Buffer
4040 *
4041 * Return Value: 1 if able to store, 0 otherwise
4042 */
4043static int save_tx_buffer_request(struct mgsl_struct *info,const char *Buffer, unsigned int BufferSize)
4044{
4045 struct tx_holding_buffer *ptx;
4046
4047 if ( info->tx_holding_count >= info->num_tx_holding_buffers ) {
4048 return 0; /* all buffers in use */
4049 }
4050
4051 ptx = &info->tx_holding_buffers[info->put_tx_holding_index];
4052 ptx->buffer_size = BufferSize;
4053 memcpy( ptx->buffer, Buffer, BufferSize);
4054
4055 ++info->tx_holding_count;
4056 if ( ++info->put_tx_holding_index >= info->num_tx_holding_buffers)
4057 info->put_tx_holding_index=0;
4058
4059 return 1;
4060}
4061
4062static int mgsl_claim_resources(struct mgsl_struct *info)
4063{
4064 if (request_region(info->io_base,info->io_addr_size,"synclink") == NULL) {
4065 printk( "%s(%d):I/O address conflict on device %s Addr=%08X\n",
4066 __FILE__,__LINE__,info->device_name, info->io_base);
4067 return -ENODEV;
4068 }
4069 info->io_addr_requested = true;
4070
4071 if ( request_irq(info->irq_level,mgsl_interrupt,info->irq_flags,
4072 info->device_name, info ) < 0 ) {
4073 printk( "%s(%d):Can't request interrupt on device %s IRQ=%d\n",
4074 __FILE__,__LINE__,info->device_name, info->irq_level );
4075 goto errout;
4076 }
4077 info->irq_requested = true;
4078
4079 if ( info->bus_type == MGSL_BUS_TYPE_PCI ) {
4080 if (request_mem_region(info->phys_memory_base,0x40000,"synclink") == NULL) {
4081 printk( "%s(%d):mem addr conflict device %s Addr=%08X\n",
4082 __FILE__,__LINE__,info->device_name, info->phys_memory_base);
4083 goto errout;
4084 }
4085 info->shared_mem_requested = true;
4086 if (request_mem_region(info->phys_lcr_base + info->lcr_offset,128,"synclink") == NULL) {
4087 printk( "%s(%d):lcr mem addr conflict device %s Addr=%08X\n",
4088 __FILE__,__LINE__,info->device_name, info->phys_lcr_base + info->lcr_offset);
4089 goto errout;
4090 }
4091 info->lcr_mem_requested = true;
4092
4093 info->memory_base = ioremap_nocache(info->phys_memory_base,
4094 0x40000);
4095 if (!info->memory_base) {
4096 printk( "%s(%d):Can't map shared memory on device %s MemAddr=%08X\n",
4097 __FILE__,__LINE__,info->device_name, info->phys_memory_base );
4098 goto errout;
4099 }
4100
4101 if ( !mgsl_memory_test(info) ) {
4102 printk( "%s(%d):Failed shared memory test %s MemAddr=%08X\n",
4103 __FILE__,__LINE__,info->device_name, info->phys_memory_base );
4104 goto errout;
4105 }
4106
4107 info->lcr_base = ioremap_nocache(info->phys_lcr_base,
4108 PAGE_SIZE);
4109 if (!info->lcr_base) {
4110 printk( "%s(%d):Can't map LCR memory on device %s MemAddr=%08X\n",
4111 __FILE__,__LINE__,info->device_name, info->phys_lcr_base );
4112 goto errout;
4113 }
4114 info->lcr_base += info->lcr_offset;
4115
4116 } else {
4117 /* claim DMA channel */
4118
4119 if (request_dma(info->dma_level,info->device_name) < 0){
4120 printk( "%s(%d):Can't request DMA channel on device %s DMA=%d\n",
4121 __FILE__,__LINE__,info->device_name, info->dma_level );
4122 mgsl_release_resources( info );
4123 return -ENODEV;
4124 }
4125 info->dma_requested = true;
4126
4127 /* ISA adapter uses bus master DMA */
4128 set_dma_mode(info->dma_level,DMA_MODE_CASCADE);
4129 enable_dma(info->dma_level);
4130 }
4131
4132 if ( mgsl_allocate_dma_buffers(info) < 0 ) {
4133 printk( "%s(%d):Can't allocate DMA buffers on device %s DMA=%d\n",
4134 __FILE__,__LINE__,info->device_name, info->dma_level );
4135 goto errout;
4136 }
4137
4138 return 0;
4139errout:
4140 mgsl_release_resources(info);
4141 return -ENODEV;
4142
4143} /* end of mgsl_claim_resources() */
4144
4145static void mgsl_release_resources(struct mgsl_struct *info)
4146{
4147 if ( debug_level >= DEBUG_LEVEL_INFO )
4148 printk( "%s(%d):mgsl_release_resources(%s) entry\n",
4149 __FILE__,__LINE__,info->device_name );
4150
4151 if ( info->irq_requested ) {
4152 free_irq(info->irq_level, info);
4153 info->irq_requested = false;
4154 }
4155 if ( info->dma_requested ) {
4156 disable_dma(info->dma_level);
4157 free_dma(info->dma_level);
4158 info->dma_requested = false;
4159 }
4160 mgsl_free_dma_buffers(info);
4161 mgsl_free_intermediate_rxbuffer_memory(info);
4162 mgsl_free_intermediate_txbuffer_memory(info);
4163
4164 if ( info->io_addr_requested ) {
4165 release_region(info->io_base,info->io_addr_size);
4166 info->io_addr_requested = false;
4167 }
4168 if ( info->shared_mem_requested ) {
4169 release_mem_region(info->phys_memory_base,0x40000);
4170 info->shared_mem_requested = false;
4171 }
4172 if ( info->lcr_mem_requested ) {
4173 release_mem_region(info->phys_lcr_base + info->lcr_offset,128);
4174 info->lcr_mem_requested = false;
4175 }
4176 if (info->memory_base){
4177 iounmap(info->memory_base);
4178 info->memory_base = NULL;
4179 }
4180 if (info->lcr_base){
4181 iounmap(info->lcr_base - info->lcr_offset);
4182 info->lcr_base = NULL;
4183 }
4184
4185 if ( debug_level >= DEBUG_LEVEL_INFO )
4186 printk( "%s(%d):mgsl_release_resources(%s) exit\n",
4187 __FILE__,__LINE__,info->device_name );
4188
4189} /* end of mgsl_release_resources() */
4190
4191/* mgsl_add_device()
4192 *
4193 * Add the specified device instance data structure to the
4194 * global linked list of devices and increment the device count.
4195 *
4196 * Arguments: info pointer to device instance data
4197 * Return Value: None
4198 */
4199static void mgsl_add_device( struct mgsl_struct *info )
4200{
4201 info->next_device = NULL;
4202 info->line = mgsl_device_count;
4203 sprintf(info->device_name,"ttySL%d",info->line);
4204
4205 if (info->line < MAX_TOTAL_DEVICES) {
4206 if (maxframe[info->line])
4207 info->max_frame_size = maxframe[info->line];
4208
4209 if (txdmabufs[info->line]) {
4210 info->num_tx_dma_buffers = txdmabufs[info->line];
4211 if (info->num_tx_dma_buffers < 1)
4212 info->num_tx_dma_buffers = 1;
4213 }
4214
4215 if (txholdbufs[info->line]) {
4216 info->num_tx_holding_buffers = txholdbufs[info->line];
4217 if (info->num_tx_holding_buffers < 1)
4218 info->num_tx_holding_buffers = 1;
4219 else if (info->num_tx_holding_buffers > MAX_TX_HOLDING_BUFFERS)
4220 info->num_tx_holding_buffers = MAX_TX_HOLDING_BUFFERS;
4221 }
4222 }
4223
4224 mgsl_device_count++;
4225
4226 if ( !mgsl_device_list )
4227 mgsl_device_list = info;
4228 else {
4229 struct mgsl_struct *current_dev = mgsl_device_list;
4230 while( current_dev->next_device )
4231 current_dev = current_dev->next_device;
4232 current_dev->next_device = info;
4233 }
4234
4235 if ( info->max_frame_size < 4096 )
4236 info->max_frame_size = 4096;
4237 else if ( info->max_frame_size > 65535 )
4238 info->max_frame_size = 65535;
4239
4240 if ( info->bus_type == MGSL_BUS_TYPE_PCI ) {
4241 printk( "SyncLink PCI v%d %s: IO=%04X IRQ=%d Mem=%08X,%08X MaxFrameSize=%u\n",
4242 info->hw_version + 1, info->device_name, info->io_base, info->irq_level,
4243 info->phys_memory_base, info->phys_lcr_base,
4244 info->max_frame_size );
4245 } else {
4246 printk( "SyncLink ISA %s: IO=%04X IRQ=%d DMA=%d MaxFrameSize=%u\n",
4247 info->device_name, info->io_base, info->irq_level, info->dma_level,
4248 info->max_frame_size );
4249 }
4250
4251#if SYNCLINK_GENERIC_HDLC
4252 hdlcdev_init(info);
4253#endif
4254
4255} /* end of mgsl_add_device() */
4256
4257static const struct tty_port_operations mgsl_port_ops = {
4258 .carrier_raised = carrier_raised,
4259 .dtr_rts = dtr_rts,
4260};
4261
4262
4263/* mgsl_allocate_device()
4264 *
4265 * Allocate and initialize a device instance structure
4266 *
4267 * Arguments: none
4268 * Return Value: pointer to mgsl_struct if success, otherwise NULL
4269 */
4270static struct mgsl_struct* mgsl_allocate_device(void)
4271{
4272 struct mgsl_struct *info;
4273
4274 info = kzalloc(sizeof(struct mgsl_struct),
4275 GFP_KERNEL);
4276
4277 if (!info) {
4278 printk("Error can't allocate device instance data\n");
4279 } else {
4280 tty_port_init(&info->port);
4281 info->port.ops = &mgsl_port_ops;
4282 info->magic = MGSL_MAGIC;
4283 INIT_WORK(&info->task, mgsl_bh_handler);
4284 info->max_frame_size = 4096;
4285 info->port.close_delay = 5*HZ/10;
4286 info->port.closing_wait = 30*HZ;
4287 init_waitqueue_head(&info->status_event_wait_q);
4288 init_waitqueue_head(&info->event_wait_q);
4289 spin_lock_init(&info->irq_spinlock);
4290 spin_lock_init(&info->netlock);
4291 memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS));
4292 info->idle_mode = HDLC_TXIDLE_FLAGS;
4293 info->num_tx_dma_buffers = 1;
4294 info->num_tx_holding_buffers = 0;
4295 }
4296
4297 return info;
4298
4299} /* end of mgsl_allocate_device()*/
4300
4301static const struct tty_operations mgsl_ops = {
4302 .open = mgsl_open,
4303 .close = mgsl_close,
4304 .write = mgsl_write,
4305 .put_char = mgsl_put_char,
4306 .flush_chars = mgsl_flush_chars,
4307 .write_room = mgsl_write_room,
4308 .chars_in_buffer = mgsl_chars_in_buffer,
4309 .flush_buffer = mgsl_flush_buffer,
4310 .ioctl = mgsl_ioctl,
4311 .throttle = mgsl_throttle,
4312 .unthrottle = mgsl_unthrottle,
4313 .send_xchar = mgsl_send_xchar,
4314 .break_ctl = mgsl_break,
4315 .wait_until_sent = mgsl_wait_until_sent,
4316 .set_termios = mgsl_set_termios,
4317 .stop = mgsl_stop,
4318 .start = mgsl_start,
4319 .hangup = mgsl_hangup,
4320 .tiocmget = tiocmget,
4321 .tiocmset = tiocmset,
4322 .get_icount = msgl_get_icount,
4323 .proc_fops = &mgsl_proc_fops,
4324};
4325
4326/*
4327 * perform tty device initialization
4328 */
4329static int mgsl_init_tty(void)
4330{
4331 int rc;
4332
4333 serial_driver = alloc_tty_driver(128);
4334 if (!serial_driver)
4335 return -ENOMEM;
4336
4337 serial_driver->owner = THIS_MODULE;
4338 serial_driver->driver_name = "synclink";
4339 serial_driver->name = "ttySL";
4340 serial_driver->major = ttymajor;
4341 serial_driver->minor_start = 64;
4342 serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
4343 serial_driver->subtype = SERIAL_TYPE_NORMAL;
4344 serial_driver->init_termios = tty_std_termios;
4345 serial_driver->init_termios.c_cflag =
4346 B9600 | CS8 | CREAD | HUPCL | CLOCAL;
4347 serial_driver->init_termios.c_ispeed = 9600;
4348 serial_driver->init_termios.c_ospeed = 9600;
4349 serial_driver->flags = TTY_DRIVER_REAL_RAW;
4350 tty_set_operations(serial_driver, &mgsl_ops);
4351 if ((rc = tty_register_driver(serial_driver)) < 0) {
4352 printk("%s(%d):Couldn't register serial driver\n",
4353 __FILE__,__LINE__);
4354 put_tty_driver(serial_driver);
4355 serial_driver = NULL;
4356 return rc;
4357 }
4358
4359 printk("%s %s, tty major#%d\n",
4360 driver_name, driver_version,
4361 serial_driver->major);
4362 return 0;
4363}
4364
4365/* enumerate user specified ISA adapters
4366 */
4367static void mgsl_enum_isa_devices(void)
4368{
4369 struct mgsl_struct *info;
4370 int i;
4371
4372 /* Check for user specified ISA devices */
4373
4374 for (i=0 ;(i < MAX_ISA_DEVICES) && io[i] && irq[i]; i++){
4375 if ( debug_level >= DEBUG_LEVEL_INFO )
4376 printk("ISA device specified io=%04X,irq=%d,dma=%d\n",
4377 io[i], irq[i], dma[i] );
4378
4379 info = mgsl_allocate_device();
4380 if ( !info ) {
4381 /* error allocating device instance data */
4382 if ( debug_level >= DEBUG_LEVEL_ERROR )
4383 printk( "can't allocate device instance data.\n");
4384 continue;
4385 }
4386
4387 /* Copy user configuration info to device instance data */
4388 info->io_base = (unsigned int)io[i];
4389 info->irq_level = (unsigned int)irq[i];
4390 info->irq_level = irq_canonicalize(info->irq_level);
4391 info->dma_level = (unsigned int)dma[i];
4392 info->bus_type = MGSL_BUS_TYPE_ISA;
4393 info->io_addr_size = 16;
4394 info->irq_flags = 0;
4395
4396 mgsl_add_device( info );
4397 }
4398}
4399
4400static void synclink_cleanup(void)
4401{
4402 int rc;
4403 struct mgsl_struct *info;
4404 struct mgsl_struct *tmp;
4405
4406 printk("Unloading %s: %s\n", driver_name, driver_version);
4407
4408 if (serial_driver) {
4409 if ((rc = tty_unregister_driver(serial_driver)))
4410 printk("%s(%d) failed to unregister tty driver err=%d\n",
4411 __FILE__,__LINE__,rc);
4412 put_tty_driver(serial_driver);
4413 }
4414
4415 info = mgsl_device_list;
4416 while(info) {
4417#if SYNCLINK_GENERIC_HDLC
4418 hdlcdev_exit(info);
4419#endif
4420 mgsl_release_resources(info);
4421 tmp = info;
4422 info = info->next_device;
4423 kfree(tmp);
4424 }
4425
4426 if (pci_registered)
4427 pci_unregister_driver(&synclink_pci_driver);
4428}
4429
4430static int __init synclink_init(void)
4431{
4432 int rc;
4433
4434 if (break_on_load) {
4435 mgsl_get_text_ptr();
4436 BREAKPOINT();
4437 }
4438
4439 printk("%s %s\n", driver_name, driver_version);
4440
4441 mgsl_enum_isa_devices();
4442 if ((rc = pci_register_driver(&synclink_pci_driver)) < 0)
4443 printk("%s:failed to register PCI driver, error=%d\n",__FILE__,rc);
4444 else
4445 pci_registered = true;
4446
4447 if ((rc = mgsl_init_tty()) < 0)
4448 goto error;
4449
4450 return 0;
4451
4452error:
4453 synclink_cleanup();
4454 return rc;
4455}
4456
4457static void __exit synclink_exit(void)
4458{
4459 synclink_cleanup();
4460}
4461
4462module_init(synclink_init);
4463module_exit(synclink_exit);
4464
4465/*
4466 * usc_RTCmd()
4467 *
4468 * Issue a USC Receive/Transmit command to the
4469 * Channel Command/Address Register (CCAR).
4470 *
4471 * Notes:
4472 *
4473 * The command is encoded in the most significant 5 bits <15..11>
4474 * of the CCAR value. Bits <10..7> of the CCAR must be preserved
4475 * and Bits <6..0> must be written as zeros.
4476 *
4477 * Arguments:
4478 *
4479 * info pointer to device information structure
4480 * Cmd command mask (use symbolic macros)
4481 *
4482 * Return Value:
4483 *
4484 * None
4485 */
4486static void usc_RTCmd( struct mgsl_struct *info, u16 Cmd )
4487{
4488 /* output command to CCAR in bits <15..11> */
4489 /* preserve bits <10..7>, bits <6..0> must be zero */
4490
4491 outw( Cmd + info->loopback_bits, info->io_base + CCAR );
4492
4493 /* Read to flush write to CCAR */
4494 if ( info->bus_type == MGSL_BUS_TYPE_PCI )
4495 inw( info->io_base + CCAR );
4496
4497} /* end of usc_RTCmd() */
4498
4499/*
4500 * usc_DmaCmd()
4501 *
4502 * Issue a DMA command to the DMA Command/Address Register (DCAR).
4503 *
4504 * Arguments:
4505 *
4506 * info pointer to device information structure
4507 * Cmd DMA command mask (usc_DmaCmd_XX Macros)
4508 *
4509 * Return Value:
4510 *
4511 * None
4512 */
4513static void usc_DmaCmd( struct mgsl_struct *info, u16 Cmd )
4514{
4515 /* write command mask to DCAR */
4516 outw( Cmd + info->mbre_bit, info->io_base );
4517
4518 /* Read to flush write to DCAR */
4519 if ( info->bus_type == MGSL_BUS_TYPE_PCI )
4520 inw( info->io_base );
4521
4522} /* end of usc_DmaCmd() */
4523
4524/*
4525 * usc_OutDmaReg()
4526 *
4527 * Write a 16-bit value to a USC DMA register
4528 *
4529 * Arguments:
4530 *
4531 * info pointer to device info structure
4532 * RegAddr register address (number) for write
4533 * RegValue 16-bit value to write to register
4534 *
4535 * Return Value:
4536 *
4537 * None
4538 *
4539 */
4540static void usc_OutDmaReg( struct mgsl_struct *info, u16 RegAddr, u16 RegValue )
4541{
4542 /* Note: The DCAR is located at the adapter base address */
4543 /* Note: must preserve state of BIT8 in DCAR */
4544
4545 outw( RegAddr + info->mbre_bit, info->io_base );
4546 outw( RegValue, info->io_base );
4547
4548 /* Read to flush write to DCAR */
4549 if ( info->bus_type == MGSL_BUS_TYPE_PCI )
4550 inw( info->io_base );
4551
4552} /* end of usc_OutDmaReg() */
4553
4554/*
4555 * usc_InDmaReg()
4556 *
4557 * Read a 16-bit value from a DMA register
4558 *
4559 * Arguments:
4560 *
4561 * info pointer to device info structure
4562 * RegAddr register address (number) to read from
4563 *
4564 * Return Value:
4565 *
4566 * The 16-bit value read from register
4567 *
4568 */
4569static u16 usc_InDmaReg( struct mgsl_struct *info, u16 RegAddr )
4570{
4571 /* Note: The DCAR is located at the adapter base address */
4572 /* Note: must preserve state of BIT8 in DCAR */
4573
4574 outw( RegAddr + info->mbre_bit, info->io_base );
4575 return inw( info->io_base );
4576
4577} /* end of usc_InDmaReg() */
4578
4579/*
4580 *
4581 * usc_OutReg()
4582 *
4583 * Write a 16-bit value to a USC serial channel register
4584 *
4585 * Arguments:
4586 *
4587 * info pointer to device info structure
4588 * RegAddr register address (number) to write to
4589 * RegValue 16-bit value to write to register
4590 *
4591 * Return Value:
4592 *
4593 * None
4594 *
4595 */
4596static void usc_OutReg( struct mgsl_struct *info, u16 RegAddr, u16 RegValue )
4597{
4598 outw( RegAddr + info->loopback_bits, info->io_base + CCAR );
4599 outw( RegValue, info->io_base + CCAR );
4600
4601 /* Read to flush write to CCAR */
4602 if ( info->bus_type == MGSL_BUS_TYPE_PCI )
4603 inw( info->io_base + CCAR );
4604
4605} /* end of usc_OutReg() */
4606
4607/*
4608 * usc_InReg()
4609 *
4610 * Reads a 16-bit value from a USC serial channel register
4611 *
4612 * Arguments:
4613 *
4614 * info pointer to device extension
4615 * RegAddr register address (number) to read from
4616 *
4617 * Return Value:
4618 *
4619 * 16-bit value read from register
4620 */
4621static u16 usc_InReg( struct mgsl_struct *info, u16 RegAddr )
4622{
4623 outw( RegAddr + info->loopback_bits, info->io_base + CCAR );
4624 return inw( info->io_base + CCAR );
4625
4626} /* end of usc_InReg() */
4627
4628/* usc_set_sdlc_mode()
4629 *
4630 * Set up the adapter for SDLC DMA communications.
4631 *
4632 * Arguments: info pointer to device instance data
4633 * Return Value: NONE
4634 */
4635static void usc_set_sdlc_mode( struct mgsl_struct *info )
4636{
4637 u16 RegValue;
4638 bool PreSL1660;
4639
4640 /*
4641 * determine if the IUSC on the adapter is pre-SL1660. If
4642 * not, take advantage of the UnderWait feature of more
4643 * modern chips. If an underrun occurs and this bit is set,
4644 * the transmitter will idle the programmed idle pattern
4645 * until the driver has time to service the underrun. Otherwise,
4646 * the dma controller may get the cycles previously requested
4647 * and begin transmitting queued tx data.
4648 */
4649 usc_OutReg(info,TMCR,0x1f);
4650 RegValue=usc_InReg(info,TMDR);
4651 PreSL1660 = (RegValue == IUSC_PRE_SL1660);
4652
4653 if ( info->params.flags & HDLC_FLAG_HDLC_LOOPMODE )
4654 {
4655 /*
4656 ** Channel Mode Register (CMR)
4657 **
4658 ** <15..14> 10 Tx Sub Modes, Send Flag on Underrun
4659 ** <13> 0 0 = Transmit Disabled (initially)
4660 ** <12> 0 1 = Consecutive Idles share common 0
4661 ** <11..8> 1110 Transmitter Mode = HDLC/SDLC Loop
4662 ** <7..4> 0000 Rx Sub Modes, addr/ctrl field handling
4663 ** <3..0> 0110 Receiver Mode = HDLC/SDLC
4664 **
4665 ** 1000 1110 0000 0110 = 0x8e06
4666 */
4667 RegValue = 0x8e06;
4668
4669 /*--------------------------------------------------
4670 * ignore user options for UnderRun Actions and
4671 * preambles
4672 *--------------------------------------------------*/
4673 }
4674 else
4675 {
4676 /* Channel mode Register (CMR)
4677 *
4678 * <15..14> 00 Tx Sub modes, Underrun Action
4679 * <13> 0 1 = Send Preamble before opening flag
4680 * <12> 0 1 = Consecutive Idles share common 0
4681 * <11..8> 0110 Transmitter mode = HDLC/SDLC
4682 * <7..4> 0000 Rx Sub modes, addr/ctrl field handling
4683 * <3..0> 0110 Receiver mode = HDLC/SDLC
4684 *
4685 * 0000 0110 0000 0110 = 0x0606
4686 */
4687 if (info->params.mode == MGSL_MODE_RAW) {
4688 RegValue = 0x0001; /* Set Receive mode = external sync */
4689
4690 usc_OutReg( info, IOCR, /* Set IOCR DCD is RxSync Detect Input */
4691 (unsigned short)((usc_InReg(info, IOCR) & ~(BIT13|BIT12)) | BIT12));
4692
4693 /*
4694 * TxSubMode:
4695 * CMR <15> 0 Don't send CRC on Tx Underrun
4696 * CMR <14> x undefined
4697 * CMR <13> 0 Send preamble before openning sync
4698 * CMR <12> 0 Send 8-bit syncs, 1=send Syncs per TxLength
4699 *
4700 * TxMode:
4701 * CMR <11-8) 0100 MonoSync
4702 *
4703 * 0x00 0100 xxxx xxxx 04xx
4704 */
4705 RegValue |= 0x0400;
4706 }
4707 else {
4708
4709 RegValue = 0x0606;
4710
4711 if ( info->params.flags & HDLC_FLAG_UNDERRUN_ABORT15 )
4712 RegValue |= BIT14;
4713 else if ( info->params.flags & HDLC_FLAG_UNDERRUN_FLAG )
4714 RegValue |= BIT15;
4715 else if ( info->params.flags & HDLC_FLAG_UNDERRUN_CRC )
4716 RegValue |= BIT15 + BIT14;
4717 }
4718
4719 if ( info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE )
4720 RegValue |= BIT13;
4721 }
4722
4723 if ( info->params.mode == MGSL_MODE_HDLC &&
4724 (info->params.flags & HDLC_FLAG_SHARE_ZERO) )
4725 RegValue |= BIT12;
4726
4727 if ( info->params.addr_filter != 0xff )
4728 {
4729 /* set up receive address filtering */
4730 usc_OutReg( info, RSR, info->params.addr_filter );
4731 RegValue |= BIT4;
4732 }
4733
4734 usc_OutReg( info, CMR, RegValue );
4735 info->cmr_value = RegValue;
4736
4737 /* Receiver mode Register (RMR)
4738 *
4739 * <15..13> 000 encoding
4740 * <12..11> 00 FCS = 16bit CRC CCITT (x15 + x12 + x5 + 1)
4741 * <10> 1 1 = Set CRC to all 1s (use for SDLC/HDLC)
4742 * <9> 0 1 = Include Receive chars in CRC
4743 * <8> 1 1 = Use Abort/PE bit as abort indicator
4744 * <7..6> 00 Even parity
4745 * <5> 0 parity disabled
4746 * <4..2> 000 Receive Char Length = 8 bits
4747 * <1..0> 00 Disable Receiver
4748 *
4749 * 0000 0101 0000 0000 = 0x0500
4750 */
4751
4752 RegValue = 0x0500;
4753
4754 switch ( info->params.encoding ) {
4755 case HDLC_ENCODING_NRZB: RegValue |= BIT13; break;
4756 case HDLC_ENCODING_NRZI_MARK: RegValue |= BIT14; break;
4757 case HDLC_ENCODING_NRZI_SPACE: RegValue |= BIT14 + BIT13; break;
4758 case HDLC_ENCODING_BIPHASE_MARK: RegValue |= BIT15; break;
4759 case HDLC_ENCODING_BIPHASE_SPACE: RegValue |= BIT15 + BIT13; break;
4760 case HDLC_ENCODING_BIPHASE_LEVEL: RegValue |= BIT15 + BIT14; break;
4761 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: RegValue |= BIT15 + BIT14 + BIT13; break;
4762 }
4763
4764 if ( (info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_16_CCITT )
4765 RegValue |= BIT9;
4766 else if ( (info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_32_CCITT )
4767 RegValue |= ( BIT12 | BIT10 | BIT9 );
4768
4769 usc_OutReg( info, RMR, RegValue );
4770
4771 /* Set the Receive count Limit Register (RCLR) to 0xffff. */
4772 /* When an opening flag of an SDLC frame is recognized the */
4773 /* Receive Character count (RCC) is loaded with the value in */
4774 /* RCLR. The RCC is decremented for each received byte. The */
4775 /* value of RCC is stored after the closing flag of the frame */
4776 /* allowing the frame size to be computed. */
4777
4778 usc_OutReg( info, RCLR, RCLRVALUE );
4779
4780 usc_RCmd( info, RCmd_SelectRicrdma_level );
4781
4782 /* Receive Interrupt Control Register (RICR)
4783 *
4784 * <15..8> ? RxFIFO DMA Request Level
4785 * <7> 0 Exited Hunt IA (Interrupt Arm)
4786 * <6> 0 Idle Received IA
4787 * <5> 0 Break/Abort IA
4788 * <4> 0 Rx Bound IA
4789 * <3> 1 Queued status reflects oldest 2 bytes in FIFO
4790 * <2> 0 Abort/PE IA
4791 * <1> 1 Rx Overrun IA
4792 * <0> 0 Select TC0 value for readback
4793 *
4794 * 0000 0000 0000 1000 = 0x000a
4795 */
4796
4797 /* Carry over the Exit Hunt and Idle Received bits */
4798 /* in case they have been armed by usc_ArmEvents. */
4799
4800 RegValue = usc_InReg( info, RICR ) & 0xc0;
4801
4802 if ( info->bus_type == MGSL_BUS_TYPE_PCI )
4803 usc_OutReg( info, RICR, (u16)(0x030a | RegValue) );
4804 else
4805 usc_OutReg( info, RICR, (u16)(0x140a | RegValue) );
4806
4807 /* Unlatch all Rx status bits and clear Rx status IRQ Pending */
4808
4809 usc_UnlatchRxstatusBits( info, RXSTATUS_ALL );
4810 usc_ClearIrqPendingBits( info, RECEIVE_STATUS );
4811
4812 /* Transmit mode Register (TMR)
4813 *
4814 * <15..13> 000 encoding
4815 * <12..11> 00 FCS = 16bit CRC CCITT (x15 + x12 + x5 + 1)
4816 * <10> 1 1 = Start CRC as all 1s (use for SDLC/HDLC)
4817 * <9> 0 1 = Tx CRC Enabled
4818 * <8> 0 1 = Append CRC to end of transmit frame
4819 * <7..6> 00 Transmit parity Even
4820 * <5> 0 Transmit parity Disabled
4821 * <4..2> 000 Tx Char Length = 8 bits
4822 * <1..0> 00 Disable Transmitter
4823 *
4824 * 0000 0100 0000 0000 = 0x0400
4825 */
4826
4827 RegValue = 0x0400;
4828
4829 switch ( info->params.encoding ) {
4830 case HDLC_ENCODING_NRZB: RegValue |= BIT13; break;
4831 case HDLC_ENCODING_NRZI_MARK: RegValue |= BIT14; break;
4832 case HDLC_ENCODING_NRZI_SPACE: RegValue |= BIT14 + BIT13; break;
4833 case HDLC_ENCODING_BIPHASE_MARK: RegValue |= BIT15; break;
4834 case HDLC_ENCODING_BIPHASE_SPACE: RegValue |= BIT15 + BIT13; break;
4835 case HDLC_ENCODING_BIPHASE_LEVEL: RegValue |= BIT15 + BIT14; break;
4836 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: RegValue |= BIT15 + BIT14 + BIT13; break;
4837 }
4838
4839 if ( (info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_16_CCITT )
4840 RegValue |= BIT9 + BIT8;
4841 else if ( (info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_32_CCITT )
4842 RegValue |= ( BIT12 | BIT10 | BIT9 | BIT8);
4843
4844 usc_OutReg( info, TMR, RegValue );
4845
4846 usc_set_txidle( info );
4847
4848
4849 usc_TCmd( info, TCmd_SelectTicrdma_level );
4850
4851 /* Transmit Interrupt Control Register (TICR)
4852 *
4853 * <15..8> ? Transmit FIFO DMA Level
4854 * <7> 0 Present IA (Interrupt Arm)
4855 * <6> 0 Idle Sent IA
4856 * <5> 1 Abort Sent IA
4857 * <4> 1 EOF/EOM Sent IA
4858 * <3> 0 CRC Sent IA
4859 * <2> 1 1 = Wait for SW Trigger to Start Frame
4860 * <1> 1 Tx Underrun IA
4861 * <0> 0 TC0 constant on read back
4862 *
4863 * 0000 0000 0011 0110 = 0x0036
4864 */
4865
4866 if ( info->bus_type == MGSL_BUS_TYPE_PCI )
4867 usc_OutReg( info, TICR, 0x0736 );
4868 else
4869 usc_OutReg( info, TICR, 0x1436 );
4870
4871 usc_UnlatchTxstatusBits( info, TXSTATUS_ALL );
4872 usc_ClearIrqPendingBits( info, TRANSMIT_STATUS );
4873
4874 /*
4875 ** Transmit Command/Status Register (TCSR)
4876 **
4877 ** <15..12> 0000 TCmd
4878 ** <11> 0/1 UnderWait
4879 ** <10..08> 000 TxIdle
4880 ** <7> x PreSent
4881 ** <6> x IdleSent
4882 ** <5> x AbortSent
4883 ** <4> x EOF/EOM Sent
4884 ** <3> x CRC Sent
4885 ** <2> x All Sent
4886 ** <1> x TxUnder
4887 ** <0> x TxEmpty
4888 **
4889 ** 0000 0000 0000 0000 = 0x0000
4890 */
4891 info->tcsr_value = 0;
4892
4893 if ( !PreSL1660 )
4894 info->tcsr_value |= TCSR_UNDERWAIT;
4895
4896 usc_OutReg( info, TCSR, info->tcsr_value );
4897
4898 /* Clock mode Control Register (CMCR)
4899 *
4900 * <15..14> 00 counter 1 Source = Disabled
4901 * <13..12> 00 counter 0 Source = Disabled
4902 * <11..10> 11 BRG1 Input is TxC Pin
4903 * <9..8> 11 BRG0 Input is TxC Pin
4904 * <7..6> 01 DPLL Input is BRG1 Output
4905 * <5..3> XXX TxCLK comes from Port 0
4906 * <2..0> XXX RxCLK comes from Port 1
4907 *
4908 * 0000 1111 0111 0111 = 0x0f77
4909 */
4910
4911 RegValue = 0x0f40;
4912
4913 if ( info->params.flags & HDLC_FLAG_RXC_DPLL )
4914 RegValue |= 0x0003; /* RxCLK from DPLL */
4915 else if ( info->params.flags & HDLC_FLAG_RXC_BRG )
4916 RegValue |= 0x0004; /* RxCLK from BRG0 */
4917 else if ( info->params.flags & HDLC_FLAG_RXC_TXCPIN)
4918 RegValue |= 0x0006; /* RxCLK from TXC Input */
4919 else
4920 RegValue |= 0x0007; /* RxCLK from Port1 */
4921
4922 if ( info->params.flags & HDLC_FLAG_TXC_DPLL )
4923 RegValue |= 0x0018; /* TxCLK from DPLL */
4924 else if ( info->params.flags & HDLC_FLAG_TXC_BRG )
4925 RegValue |= 0x0020; /* TxCLK from BRG0 */
4926 else if ( info->params.flags & HDLC_FLAG_TXC_RXCPIN)
4927 RegValue |= 0x0038; /* RxCLK from TXC Input */
4928 else
4929 RegValue |= 0x0030; /* TxCLK from Port0 */
4930
4931 usc_OutReg( info, CMCR, RegValue );
4932
4933
4934 /* Hardware Configuration Register (HCR)
4935 *
4936 * <15..14> 00 CTR0 Divisor:00=32,01=16,10=8,11=4
4937 * <13> 0 CTR1DSel:0=CTR0Div determines CTR0Div
4938 * <12> 0 CVOK:0=report code violation in biphase
4939 * <11..10> 00 DPLL Divisor:00=32,01=16,10=8,11=4
4940 * <9..8> XX DPLL mode:00=disable,01=NRZ,10=Biphase,11=Biphase Level
4941 * <7..6> 00 reserved
4942 * <5> 0 BRG1 mode:0=continuous,1=single cycle
4943 * <4> X BRG1 Enable
4944 * <3..2> 00 reserved
4945 * <1> 0 BRG0 mode:0=continuous,1=single cycle
4946 * <0> 0 BRG0 Enable
4947 */
4948
4949 RegValue = 0x0000;
4950
4951 if ( info->params.flags & (HDLC_FLAG_RXC_DPLL + HDLC_FLAG_TXC_DPLL) ) {
4952 u32 XtalSpeed;
4953 u32 DpllDivisor;
4954 u16 Tc;
4955
4956 /* DPLL is enabled. Use BRG1 to provide continuous reference clock */
4957 /* for DPLL. DPLL mode in HCR is dependent on the encoding used. */
4958
4959 if ( info->bus_type == MGSL_BUS_TYPE_PCI )
4960 XtalSpeed = 11059200;
4961 else
4962 XtalSpeed = 14745600;
4963
4964 if ( info->params.flags & HDLC_FLAG_DPLL_DIV16 ) {
4965 DpllDivisor = 16;
4966 RegValue |= BIT10;
4967 }
4968 else if ( info->params.flags & HDLC_FLAG_DPLL_DIV8 ) {
4969 DpllDivisor = 8;
4970 RegValue |= BIT11;
4971 }
4972 else
4973 DpllDivisor = 32;
4974
4975 /* Tc = (Xtal/Speed) - 1 */
4976 /* If twice the remainder of (Xtal/Speed) is greater than Speed */
4977 /* then rounding up gives a more precise time constant. Instead */
4978 /* of rounding up and then subtracting 1 we just don't subtract */
4979 /* the one in this case. */
4980
4981 /*--------------------------------------------------
4982 * ejz: for DPLL mode, application should use the
4983 * same clock speed as the partner system, even
4984 * though clocking is derived from the input RxData.
4985 * In case the user uses a 0 for the clock speed,
4986 * default to 0xffffffff and don't try to divide by
4987 * zero
4988 *--------------------------------------------------*/
4989 if ( info->params.clock_speed )
4990 {
4991 Tc = (u16)((XtalSpeed/DpllDivisor)/info->params.clock_speed);
4992 if ( !((((XtalSpeed/DpllDivisor) % info->params.clock_speed) * 2)
4993 / info->params.clock_speed) )
4994 Tc--;
4995 }
4996 else
4997 Tc = -1;
4998
4999
5000 /* Write 16-bit Time Constant for BRG1 */
5001 usc_OutReg( info, TC1R, Tc );
5002
5003 RegValue |= BIT4; /* enable BRG1 */
5004
5005 switch ( info->params.encoding ) {
5006 case HDLC_ENCODING_NRZ:
5007 case HDLC_ENCODING_NRZB:
5008 case HDLC_ENCODING_NRZI_MARK:
5009 case HDLC_ENCODING_NRZI_SPACE: RegValue |= BIT8; break;
5010 case HDLC_ENCODING_BIPHASE_MARK:
5011 case HDLC_ENCODING_BIPHASE_SPACE: RegValue |= BIT9; break;
5012 case HDLC_ENCODING_BIPHASE_LEVEL:
5013 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: RegValue |= BIT9 + BIT8; break;
5014 }
5015 }
5016
5017 usc_OutReg( info, HCR, RegValue );
5018
5019
5020 /* Channel Control/status Register (CCSR)
5021 *
5022 * <15> X RCC FIFO Overflow status (RO)
5023 * <14> X RCC FIFO Not Empty status (RO)
5024 * <13> 0 1 = Clear RCC FIFO (WO)
5025 * <12> X DPLL Sync (RW)
5026 * <11> X DPLL 2 Missed Clocks status (RO)
5027 * <10> X DPLL 1 Missed Clock status (RO)
5028 * <9..8> 00 DPLL Resync on rising and falling edges (RW)
5029 * <7> X SDLC Loop On status (RO)
5030 * <6> X SDLC Loop Send status (RO)
5031 * <5> 1 Bypass counters for TxClk and RxClk (RW)
5032 * <4..2> 000 Last Char of SDLC frame has 8 bits (RW)
5033 * <1..0> 00 reserved
5034 *
5035 * 0000 0000 0010 0000 = 0x0020
5036 */
5037
5038 usc_OutReg( info, CCSR, 0x1020 );
5039
5040
5041 if ( info->params.flags & HDLC_FLAG_AUTO_CTS ) {
5042 usc_OutReg( info, SICR,
5043 (u16)(usc_InReg(info,SICR) | SICR_CTS_INACTIVE) );
5044 }
5045
5046
5047 /* enable Master Interrupt Enable bit (MIE) */
5048 usc_EnableMasterIrqBit( info );
5049
5050 usc_ClearIrqPendingBits( info, RECEIVE_STATUS + RECEIVE_DATA +
5051 TRANSMIT_STATUS + TRANSMIT_DATA + MISC);
5052
5053 /* arm RCC underflow interrupt */
5054 usc_OutReg(info, SICR, (u16)(usc_InReg(info,SICR) | BIT3));
5055 usc_EnableInterrupts(info, MISC);
5056
5057 info->mbre_bit = 0;
5058 outw( 0, info->io_base ); /* clear Master Bus Enable (DCAR) */
5059 usc_DmaCmd( info, DmaCmd_ResetAllChannels ); /* disable both DMA channels */
5060 info->mbre_bit = BIT8;
5061 outw( BIT8, info->io_base ); /* set Master Bus Enable (DCAR) */
5062
5063 if (info->bus_type == MGSL_BUS_TYPE_ISA) {
5064 /* Enable DMAEN (Port 7, Bit 14) */
5065 /* This connects the DMA request signal to the ISA bus */
5066 usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT15) & ~BIT14));
5067 }
5068
5069 /* DMA Control Register (DCR)
5070 *
5071 * <15..14> 10 Priority mode = Alternating Tx/Rx
5072 * 01 Rx has priority
5073 * 00 Tx has priority
5074 *
5075 * <13> 1 Enable Priority Preempt per DCR<15..14>
5076 * (WARNING DCR<11..10> must be 00 when this is 1)
5077 * 0 Choose activate channel per DCR<11..10>
5078 *
5079 * <12> 0 Little Endian for Array/List
5080 * <11..10> 00 Both Channels can use each bus grant
5081 * <9..6> 0000 reserved
5082 * <5> 0 7 CLK - Minimum Bus Re-request Interval
5083 * <4> 0 1 = drive D/C and S/D pins
5084 * <3> 1 1 = Add one wait state to all DMA cycles.
5085 * <2> 0 1 = Strobe /UAS on every transfer.
5086 * <1..0> 11 Addr incrementing only affects LS24 bits
5087 *
5088 * 0110 0000 0000 1011 = 0x600b
5089 */
5090
5091 if ( info->bus_type == MGSL_BUS_TYPE_PCI ) {
5092 /* PCI adapter does not need DMA wait state */
5093 usc_OutDmaReg( info, DCR, 0xa00b );
5094 }
5095 else
5096 usc_OutDmaReg( info, DCR, 0x800b );
5097
5098
5099 /* Receive DMA mode Register (RDMR)
5100 *
5101 * <15..14> 11 DMA mode = Linked List Buffer mode
5102 * <13> 1 RSBinA/L = store Rx status Block in Arrary/List entry
5103 * <12> 1 Clear count of List Entry after fetching
5104 * <11..10> 00 Address mode = Increment
5105 * <9> 1 Terminate Buffer on RxBound
5106 * <8> 0 Bus Width = 16bits
5107 * <7..0> ? status Bits (write as 0s)
5108 *
5109 * 1111 0010 0000 0000 = 0xf200
5110 */
5111
5112 usc_OutDmaReg( info, RDMR, 0xf200 );
5113
5114
5115 /* Transmit DMA mode Register (TDMR)
5116 *
5117 * <15..14> 11 DMA mode = Linked List Buffer mode
5118 * <13> 1 TCBinA/L = fetch Tx Control Block from List entry
5119 * <12> 1 Clear count of List Entry after fetching
5120 * <11..10> 00 Address mode = Increment
5121 * <9> 1 Terminate Buffer on end of frame
5122 * <8> 0 Bus Width = 16bits
5123 * <7..0> ? status Bits (Read Only so write as 0)
5124 *
5125 * 1111 0010 0000 0000 = 0xf200
5126 */
5127
5128 usc_OutDmaReg( info, TDMR, 0xf200 );
5129
5130
5131 /* DMA Interrupt Control Register (DICR)
5132 *
5133 * <15> 1 DMA Interrupt Enable
5134 * <14> 0 1 = Disable IEO from USC
5135 * <13> 0 1 = Don't provide vector during IntAck
5136 * <12> 1 1 = Include status in Vector
5137 * <10..2> 0 reserved, Must be 0s
5138 * <1> 0 1 = Rx DMA Interrupt Enabled
5139 * <0> 0 1 = Tx DMA Interrupt Enabled
5140 *
5141 * 1001 0000 0000 0000 = 0x9000
5142 */
5143
5144 usc_OutDmaReg( info, DICR, 0x9000 );
5145
5146 usc_InDmaReg( info, RDMR ); /* clear pending receive DMA IRQ bits */
5147 usc_InDmaReg( info, TDMR ); /* clear pending transmit DMA IRQ bits */
5148 usc_OutDmaReg( info, CDIR, 0x0303 ); /* clear IUS and Pending for Tx and Rx */
5149
5150 /* Channel Control Register (CCR)
5151 *
5152 * <15..14> 10 Use 32-bit Tx Control Blocks (TCBs)
5153 * <13> 0 Trigger Tx on SW Command Disabled
5154 * <12> 0 Flag Preamble Disabled
5155 * <11..10> 00 Preamble Length
5156 * <9..8> 00 Preamble Pattern
5157 * <7..6> 10 Use 32-bit Rx status Blocks (RSBs)
5158 * <5> 0 Trigger Rx on SW Command Disabled
5159 * <4..0> 0 reserved
5160 *
5161 * 1000 0000 1000 0000 = 0x8080
5162 */
5163
5164 RegValue = 0x8080;
5165
5166 switch ( info->params.preamble_length ) {
5167 case HDLC_PREAMBLE_LENGTH_16BITS: RegValue |= BIT10; break;
5168 case HDLC_PREAMBLE_LENGTH_32BITS: RegValue |= BIT11; break;
5169 case HDLC_PREAMBLE_LENGTH_64BITS: RegValue |= BIT11 + BIT10; break;
5170 }
5171
5172 switch ( info->params.preamble ) {
5173 case HDLC_PREAMBLE_PATTERN_FLAGS: RegValue |= BIT8 + BIT12; break;
5174 case HDLC_PREAMBLE_PATTERN_ONES: RegValue |= BIT8; break;
5175 case HDLC_PREAMBLE_PATTERN_10: RegValue |= BIT9; break;
5176 case HDLC_PREAMBLE_PATTERN_01: RegValue |= BIT9 + BIT8; break;
5177 }
5178
5179 usc_OutReg( info, CCR, RegValue );
5180
5181
5182 /*
5183 * Burst/Dwell Control Register
5184 *
5185 * <15..8> 0x20 Maximum number of transfers per bus grant
5186 * <7..0> 0x00 Maximum number of clock cycles per bus grant
5187 */
5188
5189 if ( info->bus_type == MGSL_BUS_TYPE_PCI ) {
5190 /* don't limit bus occupancy on PCI adapter */
5191 usc_OutDmaReg( info, BDCR, 0x0000 );
5192 }
5193 else
5194 usc_OutDmaReg( info, BDCR, 0x2000 );
5195
5196 usc_stop_transmitter(info);
5197 usc_stop_receiver(info);
5198
5199} /* end of usc_set_sdlc_mode() */
5200
5201/* usc_enable_loopback()
5202 *
5203 * Set the 16C32 for internal loopback mode.
5204 * The TxCLK and RxCLK signals are generated from the BRG0 and
5205 * the TxD is looped back to the RxD internally.
5206 *
5207 * Arguments: info pointer to device instance data
5208 * enable 1 = enable loopback, 0 = disable
5209 * Return Value: None
5210 */
5211static void usc_enable_loopback(struct mgsl_struct *info, int enable)
5212{
5213 if (enable) {
5214 /* blank external TXD output */
5215 usc_OutReg(info,IOCR,usc_InReg(info,IOCR) | (BIT7+BIT6));
5216
5217 /* Clock mode Control Register (CMCR)
5218 *
5219 * <15..14> 00 counter 1 Disabled
5220 * <13..12> 00 counter 0 Disabled
5221 * <11..10> 11 BRG1 Input is TxC Pin
5222 * <9..8> 11 BRG0 Input is TxC Pin
5223 * <7..6> 01 DPLL Input is BRG1 Output
5224 * <5..3> 100 TxCLK comes from BRG0
5225 * <2..0> 100 RxCLK comes from BRG0
5226 *
5227 * 0000 1111 0110 0100 = 0x0f64
5228 */
5229
5230 usc_OutReg( info, CMCR, 0x0f64 );
5231
5232 /* Write 16-bit Time Constant for BRG0 */
5233 /* use clock speed if available, otherwise use 8 for diagnostics */
5234 if (info->params.clock_speed) {
5235 if (info->bus_type == MGSL_BUS_TYPE_PCI)
5236 usc_OutReg(info, TC0R, (u16)((11059200/info->params.clock_speed)-1));
5237 else
5238 usc_OutReg(info, TC0R, (u16)((14745600/info->params.clock_speed)-1));
5239 } else
5240 usc_OutReg(info, TC0R, (u16)8);
5241
5242 /* Hardware Configuration Register (HCR) Clear Bit 1, BRG0
5243 mode = Continuous Set Bit 0 to enable BRG0. */
5244 usc_OutReg( info, HCR, (u16)((usc_InReg( info, HCR ) & ~BIT1) | BIT0) );
5245
5246 /* Input/Output Control Reg, <2..0> = 100, Drive RxC pin with BRG0 */
5247 usc_OutReg(info, IOCR, (u16)((usc_InReg(info, IOCR) & 0xfff8) | 0x0004));
5248
5249 /* set Internal Data loopback mode */
5250 info->loopback_bits = 0x300;
5251 outw( 0x0300, info->io_base + CCAR );
5252 } else {
5253 /* enable external TXD output */
5254 usc_OutReg(info,IOCR,usc_InReg(info,IOCR) & ~(BIT7+BIT6));
5255
5256 /* clear Internal Data loopback mode */
5257 info->loopback_bits = 0;
5258 outw( 0,info->io_base + CCAR );
5259 }
5260
5261} /* end of usc_enable_loopback() */
5262
5263/* usc_enable_aux_clock()
5264 *
5265 * Enabled the AUX clock output at the specified frequency.
5266 *
5267 * Arguments:
5268 *
5269 * info pointer to device extension
5270 * data_rate data rate of clock in bits per second
5271 * A data rate of 0 disables the AUX clock.
5272 *
5273 * Return Value: None
5274 */
5275static void usc_enable_aux_clock( struct mgsl_struct *info, u32 data_rate )
5276{
5277 u32 XtalSpeed;
5278 u16 Tc;
5279
5280 if ( data_rate ) {
5281 if ( info->bus_type == MGSL_BUS_TYPE_PCI )
5282 XtalSpeed = 11059200;
5283 else
5284 XtalSpeed = 14745600;
5285
5286
5287 /* Tc = (Xtal/Speed) - 1 */
5288 /* If twice the remainder of (Xtal/Speed) is greater than Speed */
5289 /* then rounding up gives a more precise time constant. Instead */
5290 /* of rounding up and then subtracting 1 we just don't subtract */
5291 /* the one in this case. */
5292
5293
5294 Tc = (u16)(XtalSpeed/data_rate);
5295 if ( !(((XtalSpeed % data_rate) * 2) / data_rate) )
5296 Tc--;
5297
5298 /* Write 16-bit Time Constant for BRG0 */
5299 usc_OutReg( info, TC0R, Tc );
5300
5301 /*
5302 * Hardware Configuration Register (HCR)
5303 * Clear Bit 1, BRG0 mode = Continuous
5304 * Set Bit 0 to enable BRG0.
5305 */
5306
5307 usc_OutReg( info, HCR, (u16)((usc_InReg( info, HCR ) & ~BIT1) | BIT0) );
5308
5309 /* Input/Output Control Reg, <2..0> = 100, Drive RxC pin with BRG0 */
5310 usc_OutReg( info, IOCR, (u16)((usc_InReg(info, IOCR) & 0xfff8) | 0x0004) );
5311 } else {
5312 /* data rate == 0 so turn off BRG0 */
5313 usc_OutReg( info, HCR, (u16)(usc_InReg( info, HCR ) & ~BIT0) );
5314 }
5315
5316} /* end of usc_enable_aux_clock() */
5317
5318/*
5319 *
5320 * usc_process_rxoverrun_sync()
5321 *
5322 * This function processes a receive overrun by resetting the
5323 * receive DMA buffers and issuing a Purge Rx FIFO command
5324 * to allow the receiver to continue receiving.
5325 *
5326 * Arguments:
5327 *
5328 * info pointer to device extension
5329 *
5330 * Return Value: None
5331 */
5332static void usc_process_rxoverrun_sync( struct mgsl_struct *info )
5333{
5334 int start_index;
5335 int end_index;
5336 int frame_start_index;
5337 bool start_of_frame_found = false;
5338 bool end_of_frame_found = false;
5339 bool reprogram_dma = false;
5340
5341 DMABUFFERENTRY *buffer_list = info->rx_buffer_list;
5342 u32 phys_addr;
5343
5344 usc_DmaCmd( info, DmaCmd_PauseRxChannel );
5345 usc_RCmd( info, RCmd_EnterHuntmode );
5346 usc_RTCmd( info, RTCmd_PurgeRxFifo );
5347
5348 /* CurrentRxBuffer points to the 1st buffer of the next */
5349 /* possibly available receive frame. */
5350
5351 frame_start_index = start_index = end_index = info->current_rx_buffer;
5352
5353 /* Search for an unfinished string of buffers. This means */
5354 /* that a receive frame started (at least one buffer with */
5355 /* count set to zero) but there is no terminiting buffer */
5356 /* (status set to non-zero). */
5357
5358 while( !buffer_list[end_index].count )
5359 {
5360 /* Count field has been reset to zero by 16C32. */
5361 /* This buffer is currently in use. */
5362
5363 if ( !start_of_frame_found )
5364 {
5365 start_of_frame_found = true;
5366 frame_start_index = end_index;
5367 end_of_frame_found = false;
5368 }
5369
5370 if ( buffer_list[end_index].status )
5371 {
5372 /* Status field has been set by 16C32. */
5373 /* This is the last buffer of a received frame. */
5374
5375 /* We want to leave the buffers for this frame intact. */
5376 /* Move on to next possible frame. */
5377
5378 start_of_frame_found = false;
5379 end_of_frame_found = true;
5380 }
5381
5382 /* advance to next buffer entry in linked list */
5383 end_index++;
5384 if ( end_index == info->rx_buffer_count )
5385 end_index = 0;
5386
5387 if ( start_index == end_index )
5388 {
5389 /* The entire list has been searched with all Counts == 0 and */
5390 /* all Status == 0. The receive buffers are */
5391 /* completely screwed, reset all receive buffers! */
5392 mgsl_reset_rx_dma_buffers( info );
5393 frame_start_index = 0;
5394 start_of_frame_found = false;
5395 reprogram_dma = true;
5396 break;
5397 }
5398 }
5399
5400 if ( start_of_frame_found && !end_of_frame_found )
5401 {
5402 /* There is an unfinished string of receive DMA buffers */
5403 /* as a result of the receiver overrun. */
5404
5405 /* Reset the buffers for the unfinished frame */
5406 /* and reprogram the receive DMA controller to start */
5407 /* at the 1st buffer of unfinished frame. */
5408
5409 start_index = frame_start_index;
5410
5411 do
5412 {
5413 *((unsigned long *)&(info->rx_buffer_list[start_index++].count)) = DMABUFFERSIZE;
5414
5415 /* Adjust index for wrap around. */
5416 if ( start_index == info->rx_buffer_count )
5417 start_index = 0;
5418
5419 } while( start_index != end_index );
5420
5421 reprogram_dma = true;
5422 }
5423
5424 if ( reprogram_dma )
5425 {
5426 usc_UnlatchRxstatusBits(info,RXSTATUS_ALL);
5427 usc_ClearIrqPendingBits(info, RECEIVE_DATA|RECEIVE_STATUS);
5428 usc_UnlatchRxstatusBits(info, RECEIVE_DATA|RECEIVE_STATUS);
5429
5430 usc_EnableReceiver(info,DISABLE_UNCONDITIONAL);
5431
5432 /* This empties the receive FIFO and loads the RCC with RCLR */
5433 usc_OutReg( info, CCSR, (u16)(usc_InReg(info,CCSR) | BIT13) );
5434
5435 /* program 16C32 with physical address of 1st DMA buffer entry */
5436 phys_addr = info->rx_buffer_list[frame_start_index].phys_entry;
5437 usc_OutDmaReg( info, NRARL, (u16)phys_addr );
5438 usc_OutDmaReg( info, NRARU, (u16)(phys_addr >> 16) );
5439
5440 usc_UnlatchRxstatusBits( info, RXSTATUS_ALL );
5441 usc_ClearIrqPendingBits( info, RECEIVE_DATA + RECEIVE_STATUS );
5442 usc_EnableInterrupts( info, RECEIVE_STATUS );
5443
5444 /* 1. Arm End of Buffer (EOB) Receive DMA Interrupt (BIT2 of RDIAR) */
5445 /* 2. Enable Receive DMA Interrupts (BIT1 of DICR) */
5446
5447 usc_OutDmaReg( info, RDIAR, BIT3 + BIT2 );
5448 usc_OutDmaReg( info, DICR, (u16)(usc_InDmaReg(info,DICR) | BIT1) );
5449 usc_DmaCmd( info, DmaCmd_InitRxChannel );
5450 if ( info->params.flags & HDLC_FLAG_AUTO_DCD )
5451 usc_EnableReceiver(info,ENABLE_AUTO_DCD);
5452 else
5453 usc_EnableReceiver(info,ENABLE_UNCONDITIONAL);
5454 }
5455 else
5456 {
5457 /* This empties the receive FIFO and loads the RCC with RCLR */
5458 usc_OutReg( info, CCSR, (u16)(usc_InReg(info,CCSR) | BIT13) );
5459 usc_RTCmd( info, RTCmd_PurgeRxFifo );
5460 }
5461
5462} /* end of usc_process_rxoverrun_sync() */
5463
5464/* usc_stop_receiver()
5465 *
5466 * Disable USC receiver
5467 *
5468 * Arguments: info pointer to device instance data
5469 * Return Value: None
5470 */
5471static void usc_stop_receiver( struct mgsl_struct *info )
5472{
5473 if (debug_level >= DEBUG_LEVEL_ISR)
5474 printk("%s(%d):usc_stop_receiver(%s)\n",
5475 __FILE__,__LINE__, info->device_name );
5476
5477 /* Disable receive DMA channel. */
5478 /* This also disables receive DMA channel interrupts */
5479 usc_DmaCmd( info, DmaCmd_ResetRxChannel );
5480
5481 usc_UnlatchRxstatusBits( info, RXSTATUS_ALL );
5482 usc_ClearIrqPendingBits( info, RECEIVE_DATA + RECEIVE_STATUS );
5483 usc_DisableInterrupts( info, RECEIVE_DATA + RECEIVE_STATUS );
5484
5485 usc_EnableReceiver(info,DISABLE_UNCONDITIONAL);
5486
5487 /* This empties the receive FIFO and loads the RCC with RCLR */
5488 usc_OutReg( info, CCSR, (u16)(usc_InReg(info,CCSR) | BIT13) );
5489 usc_RTCmd( info, RTCmd_PurgeRxFifo );
5490
5491 info->rx_enabled = false;
5492 info->rx_overflow = false;
5493 info->rx_rcc_underrun = false;
5494
5495} /* end of stop_receiver() */
5496
5497/* usc_start_receiver()
5498 *
5499 * Enable the USC receiver
5500 *
5501 * Arguments: info pointer to device instance data
5502 * Return Value: None
5503 */
5504static void usc_start_receiver( struct mgsl_struct *info )
5505{
5506 u32 phys_addr;
5507
5508 if (debug_level >= DEBUG_LEVEL_ISR)
5509 printk("%s(%d):usc_start_receiver(%s)\n",
5510 __FILE__,__LINE__, info->device_name );
5511
5512 mgsl_reset_rx_dma_buffers( info );
5513 usc_stop_receiver( info );
5514
5515 usc_OutReg( info, CCSR, (u16)(usc_InReg(info,CCSR) | BIT13) );
5516 usc_RTCmd( info, RTCmd_PurgeRxFifo );
5517
5518 if ( info->params.mode == MGSL_MODE_HDLC ||
5519 info->params.mode == MGSL_MODE_RAW ) {
5520 /* DMA mode Transfers */
5521 /* Program the DMA controller. */
5522 /* Enable the DMA controller end of buffer interrupt. */
5523
5524 /* program 16C32 with physical address of 1st DMA buffer entry */
5525 phys_addr = info->rx_buffer_list[0].phys_entry;
5526 usc_OutDmaReg( info, NRARL, (u16)phys_addr );
5527 usc_OutDmaReg( info, NRARU, (u16)(phys_addr >> 16) );
5528
5529 usc_UnlatchRxstatusBits( info, RXSTATUS_ALL );
5530 usc_ClearIrqPendingBits( info, RECEIVE_DATA + RECEIVE_STATUS );
5531 usc_EnableInterrupts( info, RECEIVE_STATUS );
5532
5533 /* 1. Arm End of Buffer (EOB) Receive DMA Interrupt (BIT2 of RDIAR) */
5534 /* 2. Enable Receive DMA Interrupts (BIT1 of DICR) */
5535
5536 usc_OutDmaReg( info, RDIAR, BIT3 + BIT2 );
5537 usc_OutDmaReg( info, DICR, (u16)(usc_InDmaReg(info,DICR) | BIT1) );
5538 usc_DmaCmd( info, DmaCmd_InitRxChannel );
5539 if ( info->params.flags & HDLC_FLAG_AUTO_DCD )
5540 usc_EnableReceiver(info,ENABLE_AUTO_DCD);
5541 else
5542 usc_EnableReceiver(info,ENABLE_UNCONDITIONAL);
5543 } else {
5544 usc_UnlatchRxstatusBits(info, RXSTATUS_ALL);
5545 usc_ClearIrqPendingBits(info, RECEIVE_DATA + RECEIVE_STATUS);
5546 usc_EnableInterrupts(info, RECEIVE_DATA);
5547
5548 usc_RTCmd( info, RTCmd_PurgeRxFifo );
5549 usc_RCmd( info, RCmd_EnterHuntmode );
5550
5551 usc_EnableReceiver(info,ENABLE_UNCONDITIONAL);
5552 }
5553
5554 usc_OutReg( info, CCSR, 0x1020 );
5555
5556 info->rx_enabled = true;
5557
5558} /* end of usc_start_receiver() */
5559
5560/* usc_start_transmitter()
5561 *
5562 * Enable the USC transmitter and send a transmit frame if
5563 * one is loaded in the DMA buffers.
5564 *
5565 * Arguments: info pointer to device instance data
5566 * Return Value: None
5567 */
5568static void usc_start_transmitter( struct mgsl_struct *info )
5569{
5570 u32 phys_addr;
5571 unsigned int FrameSize;
5572
5573 if (debug_level >= DEBUG_LEVEL_ISR)
5574 printk("%s(%d):usc_start_transmitter(%s)\n",
5575 __FILE__,__LINE__, info->device_name );
5576
5577 if ( info->xmit_cnt ) {
5578
5579 /* If auto RTS enabled and RTS is inactive, then assert */
5580 /* RTS and set a flag indicating that the driver should */
5581 /* negate RTS when the transmission completes. */
5582
5583 info->drop_rts_on_tx_done = false;
5584
5585 if ( info->params.flags & HDLC_FLAG_AUTO_RTS ) {
5586 usc_get_serial_signals( info );
5587 if ( !(info->serial_signals & SerialSignal_RTS) ) {
5588 info->serial_signals |= SerialSignal_RTS;
5589 usc_set_serial_signals( info );
5590 info->drop_rts_on_tx_done = true;
5591 }
5592 }
5593
5594
5595 if ( info->params.mode == MGSL_MODE_ASYNC ) {
5596 if ( !info->tx_active ) {
5597 usc_UnlatchTxstatusBits(info, TXSTATUS_ALL);
5598 usc_ClearIrqPendingBits(info, TRANSMIT_STATUS + TRANSMIT_DATA);
5599 usc_EnableInterrupts(info, TRANSMIT_DATA);
5600 usc_load_txfifo(info);
5601 }
5602 } else {
5603 /* Disable transmit DMA controller while programming. */
5604 usc_DmaCmd( info, DmaCmd_ResetTxChannel );
5605
5606 /* Transmit DMA buffer is loaded, so program USC */
5607 /* to send the frame contained in the buffers. */
5608
5609 FrameSize = info->tx_buffer_list[info->start_tx_dma_buffer].rcc;
5610
5611 /* if operating in Raw sync mode, reset the rcc component
5612 * of the tx dma buffer entry, otherwise, the serial controller
5613 * will send a closing sync char after this count.
5614 */
5615 if ( info->params.mode == MGSL_MODE_RAW )
5616 info->tx_buffer_list[info->start_tx_dma_buffer].rcc = 0;
5617
5618 /* Program the Transmit Character Length Register (TCLR) */
5619 /* and clear FIFO (TCC is loaded with TCLR on FIFO clear) */
5620 usc_OutReg( info, TCLR, (u16)FrameSize );
5621
5622 usc_RTCmd( info, RTCmd_PurgeTxFifo );
5623
5624 /* Program the address of the 1st DMA Buffer Entry in linked list */
5625 phys_addr = info->tx_buffer_list[info->start_tx_dma_buffer].phys_entry;
5626 usc_OutDmaReg( info, NTARL, (u16)phys_addr );
5627 usc_OutDmaReg( info, NTARU, (u16)(phys_addr >> 16) );
5628
5629 usc_UnlatchTxstatusBits( info, TXSTATUS_ALL );
5630 usc_ClearIrqPendingBits( info, TRANSMIT_STATUS );
5631 usc_EnableInterrupts( info, TRANSMIT_STATUS );
5632
5633 if ( info->params.mode == MGSL_MODE_RAW &&
5634 info->num_tx_dma_buffers > 1 ) {
5635 /* When running external sync mode, attempt to 'stream' transmit */
5636 /* by filling tx dma buffers as they become available. To do this */
5637 /* we need to enable Tx DMA EOB Status interrupts : */
5638 /* */
5639 /* 1. Arm End of Buffer (EOB) Transmit DMA Interrupt (BIT2 of TDIAR) */
5640 /* 2. Enable Transmit DMA Interrupts (BIT0 of DICR) */
5641
5642 usc_OutDmaReg( info, TDIAR, BIT2|BIT3 );
5643 usc_OutDmaReg( info, DICR, (u16)(usc_InDmaReg(info,DICR) | BIT0) );
5644 }
5645
5646 /* Initialize Transmit DMA Channel */
5647 usc_DmaCmd( info, DmaCmd_InitTxChannel );
5648
5649 usc_TCmd( info, TCmd_SendFrame );
5650
5651 mod_timer(&info->tx_timer, jiffies +
5652 msecs_to_jiffies(5000));
5653 }
5654 info->tx_active = true;
5655 }
5656
5657 if ( !info->tx_enabled ) {
5658 info->tx_enabled = true;
5659 if ( info->params.flags & HDLC_FLAG_AUTO_CTS )
5660 usc_EnableTransmitter(info,ENABLE_AUTO_CTS);
5661 else
5662 usc_EnableTransmitter(info,ENABLE_UNCONDITIONAL);
5663 }
5664
5665} /* end of usc_start_transmitter() */
5666
5667/* usc_stop_transmitter()
5668 *
5669 * Stops the transmitter and DMA
5670 *
5671 * Arguments: info pointer to device isntance data
5672 * Return Value: None
5673 */
5674static void usc_stop_transmitter( struct mgsl_struct *info )
5675{
5676 if (debug_level >= DEBUG_LEVEL_ISR)
5677 printk("%s(%d):usc_stop_transmitter(%s)\n",
5678 __FILE__,__LINE__, info->device_name );
5679
5680 del_timer(&info->tx_timer);
5681
5682 usc_UnlatchTxstatusBits( info, TXSTATUS_ALL );
5683 usc_ClearIrqPendingBits( info, TRANSMIT_STATUS + TRANSMIT_DATA );
5684 usc_DisableInterrupts( info, TRANSMIT_STATUS + TRANSMIT_DATA );
5685
5686 usc_EnableTransmitter(info,DISABLE_UNCONDITIONAL);
5687 usc_DmaCmd( info, DmaCmd_ResetTxChannel );
5688 usc_RTCmd( info, RTCmd_PurgeTxFifo );
5689
5690 info->tx_enabled = false;
5691 info->tx_active = false;
5692
5693} /* end of usc_stop_transmitter() */
5694
5695/* usc_load_txfifo()
5696 *
5697 * Fill the transmit FIFO until the FIFO is full or
5698 * there is no more data to load.
5699 *
5700 * Arguments: info pointer to device extension (instance data)
5701 * Return Value: None
5702 */
5703static void usc_load_txfifo( struct mgsl_struct *info )
5704{
5705 int Fifocount;
5706 u8 TwoBytes[2];
5707
5708 if ( !info->xmit_cnt && !info->x_char )
5709 return;
5710
5711 /* Select transmit FIFO status readback in TICR */
5712 usc_TCmd( info, TCmd_SelectTicrTxFifostatus );
5713
5714 /* load the Transmit FIFO until FIFOs full or all data sent */
5715
5716 while( (Fifocount = usc_InReg(info, TICR) >> 8) && info->xmit_cnt ) {
5717 /* there is more space in the transmit FIFO and */
5718 /* there is more data in transmit buffer */
5719
5720 if ( (info->xmit_cnt > 1) && (Fifocount > 1) && !info->x_char ) {
5721 /* write a 16-bit word from transmit buffer to 16C32 */
5722
5723 TwoBytes[0] = info->xmit_buf[info->xmit_tail++];
5724 info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1);
5725 TwoBytes[1] = info->xmit_buf[info->xmit_tail++];
5726 info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1);
5727
5728 outw( *((u16 *)TwoBytes), info->io_base + DATAREG);
5729
5730 info->xmit_cnt -= 2;
5731 info->icount.tx += 2;
5732 } else {
5733 /* only 1 byte left to transmit or 1 FIFO slot left */
5734
5735 outw( (inw( info->io_base + CCAR) & 0x0780) | (TDR+LSBONLY),
5736 info->io_base + CCAR );
5737
5738 if (info->x_char) {
5739 /* transmit pending high priority char */
5740 outw( info->x_char,info->io_base + CCAR );
5741 info->x_char = 0;
5742 } else {
5743 outw( info->xmit_buf[info->xmit_tail++],info->io_base + CCAR );
5744 info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1);
5745 info->xmit_cnt--;
5746 }
5747 info->icount.tx++;
5748 }
5749 }
5750
5751} /* end of usc_load_txfifo() */
5752
5753/* usc_reset()
5754 *
5755 * Reset the adapter to a known state and prepare it for further use.
5756 *
5757 * Arguments: info pointer to device instance data
5758 * Return Value: None
5759 */
5760static void usc_reset( struct mgsl_struct *info )
5761{
5762 if ( info->bus_type == MGSL_BUS_TYPE_PCI ) {
5763 int i;
5764 u32 readval;
5765
5766 /* Set BIT30 of Misc Control Register */
5767 /* (Local Control Register 0x50) to force reset of USC. */
5768
5769 volatile u32 *MiscCtrl = (u32 *)(info->lcr_base + 0x50);
5770 u32 *LCR0BRDR = (u32 *)(info->lcr_base + 0x28);
5771
5772 info->misc_ctrl_value |= BIT30;
5773 *MiscCtrl = info->misc_ctrl_value;
5774
5775 /*
5776 * Force at least 170ns delay before clearing
5777 * reset bit. Each read from LCR takes at least
5778 * 30ns so 10 times for 300ns to be safe.
5779 */
5780 for(i=0;i<10;i++)
5781 readval = *MiscCtrl;
5782
5783 info->misc_ctrl_value &= ~BIT30;
5784 *MiscCtrl = info->misc_ctrl_value;
5785
5786 *LCR0BRDR = BUS_DESCRIPTOR(
5787 1, // Write Strobe Hold (0-3)
5788 2, // Write Strobe Delay (0-3)
5789 2, // Read Strobe Delay (0-3)
5790 0, // NWDD (Write data-data) (0-3)
5791 4, // NWAD (Write Addr-data) (0-31)
5792 0, // NXDA (Read/Write Data-Addr) (0-3)
5793 0, // NRDD (Read Data-Data) (0-3)
5794 5 // NRAD (Read Addr-Data) (0-31)
5795 );
5796 } else {
5797 /* do HW reset */
5798 outb( 0,info->io_base + 8 );
5799 }
5800
5801 info->mbre_bit = 0;
5802 info->loopback_bits = 0;
5803 info->usc_idle_mode = 0;
5804
5805 /*
5806 * Program the Bus Configuration Register (BCR)
5807 *
5808 * <15> 0 Don't use separate address
5809 * <14..6> 0 reserved
5810 * <5..4> 00 IAckmode = Default, don't care
5811 * <3> 1 Bus Request Totem Pole output
5812 * <2> 1 Use 16 Bit data bus
5813 * <1> 0 IRQ Totem Pole output
5814 * <0> 0 Don't Shift Right Addr
5815 *
5816 * 0000 0000 0000 1100 = 0x000c
5817 *
5818 * By writing to io_base + SDPIN the Wait/Ack pin is
5819 * programmed to work as a Wait pin.
5820 */
5821
5822 outw( 0x000c,info->io_base + SDPIN );
5823
5824
5825 outw( 0,info->io_base );
5826 outw( 0,info->io_base + CCAR );
5827
5828 /* select little endian byte ordering */
5829 usc_RTCmd( info, RTCmd_SelectLittleEndian );
5830
5831
5832 /* Port Control Register (PCR)
5833 *
5834 * <15..14> 11 Port 7 is Output (~DMAEN, Bit 14 : 0 = Enabled)
5835 * <13..12> 11 Port 6 is Output (~INTEN, Bit 12 : 0 = Enabled)
5836 * <11..10> 00 Port 5 is Input (No Connect, Don't Care)
5837 * <9..8> 00 Port 4 is Input (No Connect, Don't Care)
5838 * <7..6> 11 Port 3 is Output (~RTS, Bit 6 : 0 = Enabled )
5839 * <5..4> 11 Port 2 is Output (~DTR, Bit 4 : 0 = Enabled )
5840 * <3..2> 01 Port 1 is Input (Dedicated RxC)
5841 * <1..0> 01 Port 0 is Input (Dedicated TxC)
5842 *
5843 * 1111 0000 1111 0101 = 0xf0f5
5844 */
5845
5846 usc_OutReg( info, PCR, 0xf0f5 );
5847
5848
5849 /*
5850 * Input/Output Control Register
5851 *
5852 * <15..14> 00 CTS is active low input
5853 * <13..12> 00 DCD is active low input
5854 * <11..10> 00 TxREQ pin is input (DSR)
5855 * <9..8> 00 RxREQ pin is input (RI)
5856 * <7..6> 00 TxD is output (Transmit Data)
5857 * <5..3> 000 TxC Pin in Input (14.7456MHz Clock)
5858 * <2..0> 100 RxC is Output (drive with BRG0)
5859 *
5860 * 0000 0000 0000 0100 = 0x0004
5861 */
5862
5863 usc_OutReg( info, IOCR, 0x0004 );
5864
5865} /* end of usc_reset() */
5866
5867/* usc_set_async_mode()
5868 *
5869 * Program adapter for asynchronous communications.
5870 *
5871 * Arguments: info pointer to device instance data
5872 * Return Value: None
5873 */
5874static void usc_set_async_mode( struct mgsl_struct *info )
5875{
5876 u16 RegValue;
5877
5878 /* disable interrupts while programming USC */
5879 usc_DisableMasterIrqBit( info );
5880
5881 outw( 0, info->io_base ); /* clear Master Bus Enable (DCAR) */
5882 usc_DmaCmd( info, DmaCmd_ResetAllChannels ); /* disable both DMA channels */
5883
5884 usc_loopback_frame( info );
5885
5886 /* Channel mode Register (CMR)
5887 *
5888 * <15..14> 00 Tx Sub modes, 00 = 1 Stop Bit
5889 * <13..12> 00 00 = 16X Clock
5890 * <11..8> 0000 Transmitter mode = Asynchronous
5891 * <7..6> 00 reserved?
5892 * <5..4> 00 Rx Sub modes, 00 = 16X Clock
5893 * <3..0> 0000 Receiver mode = Asynchronous
5894 *
5895 * 0000 0000 0000 0000 = 0x0
5896 */
5897
5898 RegValue = 0;
5899 if ( info->params.stop_bits != 1 )
5900 RegValue |= BIT14;
5901 usc_OutReg( info, CMR, RegValue );
5902
5903
5904 /* Receiver mode Register (RMR)
5905 *
5906 * <15..13> 000 encoding = None
5907 * <12..08> 00000 reserved (Sync Only)
5908 * <7..6> 00 Even parity
5909 * <5> 0 parity disabled
5910 * <4..2> 000 Receive Char Length = 8 bits
5911 * <1..0> 00 Disable Receiver
5912 *
5913 * 0000 0000 0000 0000 = 0x0
5914 */
5915
5916 RegValue = 0;
5917
5918 if ( info->params.data_bits != 8 )
5919 RegValue |= BIT4+BIT3+BIT2;
5920
5921 if ( info->params.parity != ASYNC_PARITY_NONE ) {
5922 RegValue |= BIT5;
5923 if ( info->params.parity != ASYNC_PARITY_ODD )
5924 RegValue |= BIT6;
5925 }
5926
5927 usc_OutReg( info, RMR, RegValue );
5928
5929
5930 /* Set IRQ trigger level */
5931
5932 usc_RCmd( info, RCmd_SelectRicrIntLevel );
5933
5934
5935 /* Receive Interrupt Control Register (RICR)
5936 *
5937 * <15..8> ? RxFIFO IRQ Request Level
5938 *
5939 * Note: For async mode the receive FIFO level must be set
5940 * to 0 to avoid the situation where the FIFO contains fewer bytes
5941 * than the trigger level and no more data is expected.
5942 *
5943 * <7> 0 Exited Hunt IA (Interrupt Arm)
5944 * <6> 0 Idle Received IA
5945 * <5> 0 Break/Abort IA
5946 * <4> 0 Rx Bound IA
5947 * <3> 0 Queued status reflects oldest byte in FIFO
5948 * <2> 0 Abort/PE IA
5949 * <1> 0 Rx Overrun IA
5950 * <0> 0 Select TC0 value for readback
5951 *
5952 * 0000 0000 0100 0000 = 0x0000 + (FIFOLEVEL in MSB)
5953 */
5954
5955 usc_OutReg( info, RICR, 0x0000 );
5956
5957 usc_UnlatchRxstatusBits( info, RXSTATUS_ALL );
5958 usc_ClearIrqPendingBits( info, RECEIVE_STATUS );
5959
5960
5961 /* Transmit mode Register (TMR)
5962 *
5963 * <15..13> 000 encoding = None
5964 * <12..08> 00000 reserved (Sync Only)
5965 * <7..6> 00 Transmit parity Even
5966 * <5> 0 Transmit parity Disabled
5967 * <4..2> 000 Tx Char Length = 8 bits
5968 * <1..0> 00 Disable Transmitter
5969 *
5970 * 0000 0000 0000 0000 = 0x0
5971 */
5972
5973 RegValue = 0;
5974
5975 if ( info->params.data_bits != 8 )
5976 RegValue |= BIT4+BIT3+BIT2;
5977
5978 if ( info->params.parity != ASYNC_PARITY_NONE ) {
5979 RegValue |= BIT5;
5980 if ( info->params.parity != ASYNC_PARITY_ODD )
5981 RegValue |= BIT6;
5982 }
5983
5984 usc_OutReg( info, TMR, RegValue );
5985
5986 usc_set_txidle( info );
5987
5988
5989 /* Set IRQ trigger level */
5990
5991 usc_TCmd( info, TCmd_SelectTicrIntLevel );
5992
5993
5994 /* Transmit Interrupt Control Register (TICR)
5995 *
5996 * <15..8> ? Transmit FIFO IRQ Level
5997 * <7> 0 Present IA (Interrupt Arm)
5998 * <6> 1 Idle Sent IA
5999 * <5> 0 Abort Sent IA
6000 * <4> 0 EOF/EOM Sent IA
6001 * <3> 0 CRC Sent IA
6002 * <2> 0 1 = Wait for SW Trigger to Start Frame
6003 * <1> 0 Tx Underrun IA
6004 * <0> 0 TC0 constant on read back
6005 *
6006 * 0000 0000 0100 0000 = 0x0040
6007 */
6008
6009 usc_OutReg( info, TICR, 0x1f40 );
6010
6011 usc_UnlatchTxstatusBits( info, TXSTATUS_ALL );
6012 usc_ClearIrqPendingBits( info, TRANSMIT_STATUS );
6013
6014 usc_enable_async_clock( info, info->params.data_rate );
6015
6016
6017 /* Channel Control/status Register (CCSR)
6018 *
6019 * <15> X RCC FIFO Overflow status (RO)
6020 * <14> X RCC FIFO Not Empty status (RO)
6021 * <13> 0 1 = Clear RCC FIFO (WO)
6022 * <12> X DPLL in Sync status (RO)
6023 * <11> X DPLL 2 Missed Clocks status (RO)
6024 * <10> X DPLL 1 Missed Clock status (RO)
6025 * <9..8> 00 DPLL Resync on rising and falling edges (RW)
6026 * <7> X SDLC Loop On status (RO)
6027 * <6> X SDLC Loop Send status (RO)
6028 * <5> 1 Bypass counters for TxClk and RxClk (RW)
6029 * <4..2> 000 Last Char of SDLC frame has 8 bits (RW)
6030 * <1..0> 00 reserved
6031 *
6032 * 0000 0000 0010 0000 = 0x0020
6033 */
6034
6035 usc_OutReg( info, CCSR, 0x0020 );
6036
6037 usc_DisableInterrupts( info, TRANSMIT_STATUS + TRANSMIT_DATA +
6038 RECEIVE_DATA + RECEIVE_STATUS );
6039
6040 usc_ClearIrqPendingBits( info, TRANSMIT_STATUS + TRANSMIT_DATA +
6041 RECEIVE_DATA + RECEIVE_STATUS );
6042
6043 usc_EnableMasterIrqBit( info );
6044
6045 if (info->bus_type == MGSL_BUS_TYPE_ISA) {
6046 /* Enable INTEN (Port 6, Bit12) */
6047 /* This connects the IRQ request signal to the ISA bus */
6048 usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT13) & ~BIT12));
6049 }
6050
6051 if (info->params.loopback) {
6052 info->loopback_bits = 0x300;
6053 outw(0x0300, info->io_base + CCAR);
6054 }
6055
6056} /* end of usc_set_async_mode() */
6057
6058/* usc_loopback_frame()
6059 *
6060 * Loop back a small (2 byte) dummy SDLC frame.
6061 * Interrupts and DMA are NOT used. The purpose of this is to
6062 * clear any 'stale' status info left over from running in async mode.
6063 *
6064 * The 16C32 shows the strange behaviour of marking the 1st
6065 * received SDLC frame with a CRC error even when there is no
6066 * CRC error. To get around this a small dummy from of 2 bytes
6067 * is looped back when switching from async to sync mode.
6068 *
6069 * Arguments: info pointer to device instance data
6070 * Return Value: None
6071 */
6072static void usc_loopback_frame( struct mgsl_struct *info )
6073{
6074 int i;
6075 unsigned long oldmode = info->params.mode;
6076
6077 info->params.mode = MGSL_MODE_HDLC;
6078
6079 usc_DisableMasterIrqBit( info );
6080
6081 usc_set_sdlc_mode( info );
6082 usc_enable_loopback( info, 1 );
6083
6084 /* Write 16-bit Time Constant for BRG0 */
6085 usc_OutReg( info, TC0R, 0 );
6086
6087 /* Channel Control Register (CCR)
6088 *
6089 * <15..14> 00 Don't use 32-bit Tx Control Blocks (TCBs)
6090 * <13> 0 Trigger Tx on SW Command Disabled
6091 * <12> 0 Flag Preamble Disabled
6092 * <11..10> 00 Preamble Length = 8-Bits
6093 * <9..8> 01 Preamble Pattern = flags
6094 * <7..6> 10 Don't use 32-bit Rx status Blocks (RSBs)
6095 * <5> 0 Trigger Rx on SW Command Disabled
6096 * <4..0> 0 reserved
6097 *
6098 * 0000 0001 0000 0000 = 0x0100
6099 */
6100
6101 usc_OutReg( info, CCR, 0x0100 );
6102
6103 /* SETUP RECEIVER */
6104 usc_RTCmd( info, RTCmd_PurgeRxFifo );
6105 usc_EnableReceiver(info,ENABLE_UNCONDITIONAL);
6106
6107 /* SETUP TRANSMITTER */
6108 /* Program the Transmit Character Length Register (TCLR) */
6109 /* and clear FIFO (TCC is loaded with TCLR on FIFO clear) */
6110 usc_OutReg( info, TCLR, 2 );
6111 usc_RTCmd( info, RTCmd_PurgeTxFifo );
6112
6113 /* unlatch Tx status bits, and start transmit channel. */
6114 usc_UnlatchTxstatusBits(info,TXSTATUS_ALL);
6115 outw(0,info->io_base + DATAREG);
6116
6117 /* ENABLE TRANSMITTER */
6118 usc_TCmd( info, TCmd_SendFrame );
6119 usc_EnableTransmitter(info,ENABLE_UNCONDITIONAL);
6120
6121 /* WAIT FOR RECEIVE COMPLETE */
6122 for (i=0 ; i<1000 ; i++)
6123 if (usc_InReg( info, RCSR ) & (BIT8 + BIT4 + BIT3 + BIT1))
6124 break;
6125
6126 /* clear Internal Data loopback mode */
6127 usc_enable_loopback(info, 0);
6128
6129 usc_EnableMasterIrqBit(info);
6130
6131 info->params.mode = oldmode;
6132
6133} /* end of usc_loopback_frame() */
6134
6135/* usc_set_sync_mode() Programs the USC for SDLC communications.
6136 *
6137 * Arguments: info pointer to adapter info structure
6138 * Return Value: None
6139 */
6140static void usc_set_sync_mode( struct mgsl_struct *info )
6141{
6142 usc_loopback_frame( info );
6143 usc_set_sdlc_mode( info );
6144
6145 if (info->bus_type == MGSL_BUS_TYPE_ISA) {
6146 /* Enable INTEN (Port 6, Bit12) */
6147 /* This connects the IRQ request signal to the ISA bus */
6148 usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT13) & ~BIT12));
6149 }
6150
6151 usc_enable_aux_clock(info, info->params.clock_speed);
6152
6153 if (info->params.loopback)
6154 usc_enable_loopback(info,1);
6155
6156} /* end of mgsl_set_sync_mode() */
6157
6158/* usc_set_txidle() Set the HDLC idle mode for the transmitter.
6159 *
6160 * Arguments: info pointer to device instance data
6161 * Return Value: None
6162 */
6163static void usc_set_txidle( struct mgsl_struct *info )
6164{
6165 u16 usc_idle_mode = IDLEMODE_FLAGS;
6166
6167 /* Map API idle mode to USC register bits */
6168
6169 switch( info->idle_mode ){
6170 case HDLC_TXIDLE_FLAGS: usc_idle_mode = IDLEMODE_FLAGS; break;
6171 case HDLC_TXIDLE_ALT_ZEROS_ONES: usc_idle_mode = IDLEMODE_ALT_ONE_ZERO; break;
6172 case HDLC_TXIDLE_ZEROS: usc_idle_mode = IDLEMODE_ZERO; break;
6173 case HDLC_TXIDLE_ONES: usc_idle_mode = IDLEMODE_ONE; break;
6174 case HDLC_TXIDLE_ALT_MARK_SPACE: usc_idle_mode = IDLEMODE_ALT_MARK_SPACE; break;
6175 case HDLC_TXIDLE_SPACE: usc_idle_mode = IDLEMODE_SPACE; break;
6176 case HDLC_TXIDLE_MARK: usc_idle_mode = IDLEMODE_MARK; break;
6177 }
6178
6179 info->usc_idle_mode = usc_idle_mode;
6180 //usc_OutReg(info, TCSR, usc_idle_mode);
6181 info->tcsr_value &= ~IDLEMODE_MASK; /* clear idle mode bits */
6182 info->tcsr_value += usc_idle_mode;
6183 usc_OutReg(info, TCSR, info->tcsr_value);
6184
6185 /*
6186 * if SyncLink WAN adapter is running in external sync mode, the
6187 * transmitter has been set to Monosync in order to try to mimic
6188 * a true raw outbound bit stream. Monosync still sends an open/close
6189 * sync char at the start/end of a frame. Try to match those sync
6190 * patterns to the idle mode set here
6191 */
6192 if ( info->params.mode == MGSL_MODE_RAW ) {
6193 unsigned char syncpat = 0;
6194 switch( info->idle_mode ) {
6195 case HDLC_TXIDLE_FLAGS:
6196 syncpat = 0x7e;
6197 break;
6198 case HDLC_TXIDLE_ALT_ZEROS_ONES:
6199 syncpat = 0x55;
6200 break;
6201 case HDLC_TXIDLE_ZEROS:
6202 case HDLC_TXIDLE_SPACE:
6203 syncpat = 0x00;
6204 break;
6205 case HDLC_TXIDLE_ONES:
6206 case HDLC_TXIDLE_MARK:
6207 syncpat = 0xff;
6208 break;
6209 case HDLC_TXIDLE_ALT_MARK_SPACE:
6210 syncpat = 0xaa;
6211 break;
6212 }
6213
6214 usc_SetTransmitSyncChars(info,syncpat,syncpat);
6215 }
6216
6217} /* end of usc_set_txidle() */
6218
6219/* usc_get_serial_signals()
6220 *
6221 * Query the adapter for the state of the V24 status (input) signals.
6222 *
6223 * Arguments: info pointer to device instance data
6224 * Return Value: None
6225 */
6226static void usc_get_serial_signals( struct mgsl_struct *info )
6227{
6228 u16 status;
6229
6230 /* clear all serial signals except DTR and RTS */
6231 info->serial_signals &= SerialSignal_DTR + SerialSignal_RTS;
6232
6233 /* Read the Misc Interrupt status Register (MISR) to get */
6234 /* the V24 status signals. */
6235
6236 status = usc_InReg( info, MISR );
6237
6238 /* set serial signal bits to reflect MISR */
6239
6240 if ( status & MISCSTATUS_CTS )
6241 info->serial_signals |= SerialSignal_CTS;
6242
6243 if ( status & MISCSTATUS_DCD )
6244 info->serial_signals |= SerialSignal_DCD;
6245
6246 if ( status & MISCSTATUS_RI )
6247 info->serial_signals |= SerialSignal_RI;
6248
6249 if ( status & MISCSTATUS_DSR )
6250 info->serial_signals |= SerialSignal_DSR;
6251
6252} /* end of usc_get_serial_signals() */
6253
6254/* usc_set_serial_signals()
6255 *
6256 * Set the state of DTR and RTS based on contents of
6257 * serial_signals member of device extension.
6258 *
6259 * Arguments: info pointer to device instance data
6260 * Return Value: None
6261 */
6262static void usc_set_serial_signals( struct mgsl_struct *info )
6263{
6264 u16 Control;
6265 unsigned char V24Out = info->serial_signals;
6266
6267 /* get the current value of the Port Control Register (PCR) */
6268
6269 Control = usc_InReg( info, PCR );
6270
6271 if ( V24Out & SerialSignal_RTS )
6272 Control &= ~(BIT6);
6273 else
6274 Control |= BIT6;
6275
6276 if ( V24Out & SerialSignal_DTR )
6277 Control &= ~(BIT4);
6278 else
6279 Control |= BIT4;
6280
6281 usc_OutReg( info, PCR, Control );
6282
6283} /* end of usc_set_serial_signals() */
6284
6285/* usc_enable_async_clock()
6286 *
6287 * Enable the async clock at the specified frequency.
6288 *
6289 * Arguments: info pointer to device instance data
6290 * data_rate data rate of clock in bps
6291 * 0 disables the AUX clock.
6292 * Return Value: None
6293 */
6294static void usc_enable_async_clock( struct mgsl_struct *info, u32 data_rate )
6295{
6296 if ( data_rate ) {
6297 /*
6298 * Clock mode Control Register (CMCR)
6299 *
6300 * <15..14> 00 counter 1 Disabled
6301 * <13..12> 00 counter 0 Disabled
6302 * <11..10> 11 BRG1 Input is TxC Pin
6303 * <9..8> 11 BRG0 Input is TxC Pin
6304 * <7..6> 01 DPLL Input is BRG1 Output
6305 * <5..3> 100 TxCLK comes from BRG0
6306 * <2..0> 100 RxCLK comes from BRG0
6307 *
6308 * 0000 1111 0110 0100 = 0x0f64
6309 */
6310
6311 usc_OutReg( info, CMCR, 0x0f64 );
6312
6313
6314 /*
6315 * Write 16-bit Time Constant for BRG0
6316 * Time Constant = (ClkSpeed / data_rate) - 1
6317 * ClkSpeed = 921600 (ISA), 691200 (PCI)
6318 */
6319
6320 if ( info->bus_type == MGSL_BUS_TYPE_PCI )
6321 usc_OutReg( info, TC0R, (u16)((691200/data_rate) - 1) );
6322 else
6323 usc_OutReg( info, TC0R, (u16)((921600/data_rate) - 1) );
6324
6325
6326 /*
6327 * Hardware Configuration Register (HCR)
6328 * Clear Bit 1, BRG0 mode = Continuous
6329 * Set Bit 0 to enable BRG0.
6330 */
6331
6332 usc_OutReg( info, HCR,
6333 (u16)((usc_InReg( info, HCR ) & ~BIT1) | BIT0) );
6334
6335
6336 /* Input/Output Control Reg, <2..0> = 100, Drive RxC pin with BRG0 */
6337
6338 usc_OutReg( info, IOCR,
6339 (u16)((usc_InReg(info, IOCR) & 0xfff8) | 0x0004) );
6340 } else {
6341 /* data rate == 0 so turn off BRG0 */
6342 usc_OutReg( info, HCR, (u16)(usc_InReg( info, HCR ) & ~BIT0) );
6343 }
6344
6345} /* end of usc_enable_async_clock() */
6346
6347/*
6348 * Buffer Structures:
6349 *
6350 * Normal memory access uses virtual addresses that can make discontiguous
6351 * physical memory pages appear to be contiguous in the virtual address
6352 * space (the processors memory mapping handles the conversions).
6353 *
6354 * DMA transfers require physically contiguous memory. This is because
6355 * the DMA system controller and DMA bus masters deal with memory using
6356 * only physical addresses.
6357 *
6358 * This causes a problem under Windows NT when large DMA buffers are
6359 * needed. Fragmentation of the nonpaged pool prevents allocations of
6360 * physically contiguous buffers larger than the PAGE_SIZE.
6361 *
6362 * However the 16C32 supports Bus Master Scatter/Gather DMA which
6363 * allows DMA transfers to physically discontiguous buffers. Information
6364 * about each data transfer buffer is contained in a memory structure
6365 * called a 'buffer entry'. A list of buffer entries is maintained
6366 * to track and control the use of the data transfer buffers.
6367 *
6368 * To support this strategy we will allocate sufficient PAGE_SIZE
6369 * contiguous memory buffers to allow for the total required buffer
6370 * space.
6371 *
6372 * The 16C32 accesses the list of buffer entries using Bus Master
6373 * DMA. Control information is read from the buffer entries by the
6374 * 16C32 to control data transfers. status information is written to
6375 * the buffer entries by the 16C32 to indicate the status of completed
6376 * transfers.
6377 *
6378 * The CPU writes control information to the buffer entries to control
6379 * the 16C32 and reads status information from the buffer entries to
6380 * determine information about received and transmitted frames.
6381 *
6382 * Because the CPU and 16C32 (adapter) both need simultaneous access
6383 * to the buffer entries, the buffer entry memory is allocated with
6384 * HalAllocateCommonBuffer(). This restricts the size of the buffer
6385 * entry list to PAGE_SIZE.
6386 *
6387 * The actual data buffers on the other hand will only be accessed
6388 * by the CPU or the adapter but not by both simultaneously. This allows
6389 * Scatter/Gather packet based DMA procedures for using physically
6390 * discontiguous pages.
6391 */
6392
6393/*
6394 * mgsl_reset_tx_dma_buffers()
6395 *
6396 * Set the count for all transmit buffers to 0 to indicate the
6397 * buffer is available for use and set the current buffer to the
6398 * first buffer. This effectively makes all buffers free and
6399 * discards any data in buffers.
6400 *
6401 * Arguments: info pointer to device instance data
6402 * Return Value: None
6403 */
6404static void mgsl_reset_tx_dma_buffers( struct mgsl_struct *info )
6405{
6406 unsigned int i;
6407
6408 for ( i = 0; i < info->tx_buffer_count; i++ ) {
6409 *((unsigned long *)&(info->tx_buffer_list[i].count)) = 0;
6410 }
6411
6412 info->current_tx_buffer = 0;
6413 info->start_tx_dma_buffer = 0;
6414 info->tx_dma_buffers_used = 0;
6415
6416 info->get_tx_holding_index = 0;
6417 info->put_tx_holding_index = 0;
6418 info->tx_holding_count = 0;
6419
6420} /* end of mgsl_reset_tx_dma_buffers() */
6421
6422/*
6423 * num_free_tx_dma_buffers()
6424 *
6425 * returns the number of free tx dma buffers available
6426 *
6427 * Arguments: info pointer to device instance data
6428 * Return Value: number of free tx dma buffers
6429 */
6430static int num_free_tx_dma_buffers(struct mgsl_struct *info)
6431{
6432 return info->tx_buffer_count - info->tx_dma_buffers_used;
6433}
6434
6435/*
6436 * mgsl_reset_rx_dma_buffers()
6437 *
6438 * Set the count for all receive buffers to DMABUFFERSIZE
6439 * and set the current buffer to the first buffer. This effectively
6440 * makes all buffers free and discards any data in buffers.
6441 *
6442 * Arguments: info pointer to device instance data
6443 * Return Value: None
6444 */
6445static void mgsl_reset_rx_dma_buffers( struct mgsl_struct *info )
6446{
6447 unsigned int i;
6448
6449 for ( i = 0; i < info->rx_buffer_count; i++ ) {
6450 *((unsigned long *)&(info->rx_buffer_list[i].count)) = DMABUFFERSIZE;
6451// info->rx_buffer_list[i].count = DMABUFFERSIZE;
6452// info->rx_buffer_list[i].status = 0;
6453 }
6454
6455 info->current_rx_buffer = 0;
6456
6457} /* end of mgsl_reset_rx_dma_buffers() */
6458
6459/*
6460 * mgsl_free_rx_frame_buffers()
6461 *
6462 * Free the receive buffers used by a received SDLC
6463 * frame such that the buffers can be reused.
6464 *
6465 * Arguments:
6466 *
6467 * info pointer to device instance data
6468 * StartIndex index of 1st receive buffer of frame
6469 * EndIndex index of last receive buffer of frame
6470 *
6471 * Return Value: None
6472 */
6473static void mgsl_free_rx_frame_buffers( struct mgsl_struct *info, unsigned int StartIndex, unsigned int EndIndex )
6474{
6475 bool Done = false;
6476 DMABUFFERENTRY *pBufEntry;
6477 unsigned int Index;
6478
6479 /* Starting with 1st buffer entry of the frame clear the status */
6480 /* field and set the count field to DMA Buffer Size. */
6481
6482 Index = StartIndex;
6483
6484 while( !Done ) {
6485 pBufEntry = &(info->rx_buffer_list[Index]);
6486
6487 if ( Index == EndIndex ) {
6488 /* This is the last buffer of the frame! */
6489 Done = true;
6490 }
6491
6492 /* reset current buffer for reuse */
6493// pBufEntry->status = 0;
6494// pBufEntry->count = DMABUFFERSIZE;
6495 *((unsigned long *)&(pBufEntry->count)) = DMABUFFERSIZE;
6496
6497 /* advance to next buffer entry in linked list */
6498 Index++;
6499 if ( Index == info->rx_buffer_count )
6500 Index = 0;
6501 }
6502
6503 /* set current buffer to next buffer after last buffer of frame */
6504 info->current_rx_buffer = Index;
6505
6506} /* end of free_rx_frame_buffers() */
6507
6508/* mgsl_get_rx_frame()
6509 *
6510 * This function attempts to return a received SDLC frame from the
6511 * receive DMA buffers. Only frames received without errors are returned.
6512 *
6513 * Arguments: info pointer to device extension
6514 * Return Value: true if frame returned, otherwise false
6515 */
6516static bool mgsl_get_rx_frame(struct mgsl_struct *info)
6517{
6518 unsigned int StartIndex, EndIndex; /* index of 1st and last buffers of Rx frame */
6519 unsigned short status;
6520 DMABUFFERENTRY *pBufEntry;
6521 unsigned int framesize = 0;
6522 bool ReturnCode = false;
6523 unsigned long flags;
6524 struct tty_struct *tty = info->port.tty;
6525 bool return_frame = false;
6526
6527 /*
6528 * current_rx_buffer points to the 1st buffer of the next available
6529 * receive frame. To find the last buffer of the frame look for
6530 * a non-zero status field in the buffer entries. (The status
6531 * field is set by the 16C32 after completing a receive frame.
6532 */
6533
6534 StartIndex = EndIndex = info->current_rx_buffer;
6535
6536 while( !info->rx_buffer_list[EndIndex].status ) {
6537 /*
6538 * If the count field of the buffer entry is non-zero then
6539 * this buffer has not been used. (The 16C32 clears the count
6540 * field when it starts using the buffer.) If an unused buffer
6541 * is encountered then there are no frames available.
6542 */
6543
6544 if ( info->rx_buffer_list[EndIndex].count )
6545 goto Cleanup;
6546
6547 /* advance to next buffer entry in linked list */
6548 EndIndex++;
6549 if ( EndIndex == info->rx_buffer_count )
6550 EndIndex = 0;
6551
6552 /* if entire list searched then no frame available */
6553 if ( EndIndex == StartIndex ) {
6554 /* If this occurs then something bad happened,
6555 * all buffers have been 'used' but none mark
6556 * the end of a frame. Reset buffers and receiver.
6557 */
6558
6559 if ( info->rx_enabled ){
6560 spin_lock_irqsave(&info->irq_spinlock,flags);
6561 usc_start_receiver(info);
6562 spin_unlock_irqrestore(&info->irq_spinlock,flags);
6563 }
6564 goto Cleanup;
6565 }
6566 }
6567
6568
6569 /* check status of receive frame */
6570
6571 status = info->rx_buffer_list[EndIndex].status;
6572
6573 if ( status & (RXSTATUS_SHORT_FRAME + RXSTATUS_OVERRUN +
6574 RXSTATUS_CRC_ERROR + RXSTATUS_ABORT) ) {
6575 if ( status & RXSTATUS_SHORT_FRAME )
6576 info->icount.rxshort++;
6577 else if ( status & RXSTATUS_ABORT )
6578 info->icount.rxabort++;
6579 else if ( status & RXSTATUS_OVERRUN )
6580 info->icount.rxover++;
6581 else {
6582 info->icount.rxcrc++;
6583 if ( info->params.crc_type & HDLC_CRC_RETURN_EX )
6584 return_frame = true;
6585 }
6586 framesize = 0;
6587#if SYNCLINK_GENERIC_HDLC
6588 {
6589 info->netdev->stats.rx_errors++;
6590 info->netdev->stats.rx_frame_errors++;
6591 }
6592#endif
6593 } else
6594 return_frame = true;
6595
6596 if ( return_frame ) {
6597 /* receive frame has no errors, get frame size.
6598 * The frame size is the starting value of the RCC (which was
6599 * set to 0xffff) minus the ending value of the RCC (decremented
6600 * once for each receive character) minus 2 for the 16-bit CRC.
6601 */
6602
6603 framesize = RCLRVALUE - info->rx_buffer_list[EndIndex].rcc;
6604
6605 /* adjust frame size for CRC if any */
6606 if ( info->params.crc_type == HDLC_CRC_16_CCITT )
6607 framesize -= 2;
6608 else if ( info->params.crc_type == HDLC_CRC_32_CCITT )
6609 framesize -= 4;
6610 }
6611
6612 if ( debug_level >= DEBUG_LEVEL_BH )
6613 printk("%s(%d):mgsl_get_rx_frame(%s) status=%04X size=%d\n",
6614 __FILE__,__LINE__,info->device_name,status,framesize);
6615
6616 if ( debug_level >= DEBUG_LEVEL_DATA )
6617 mgsl_trace_block(info,info->rx_buffer_list[StartIndex].virt_addr,
6618 min_t(int, framesize, DMABUFFERSIZE),0);
6619
6620 if (framesize) {
6621 if ( ( (info->params.crc_type & HDLC_CRC_RETURN_EX) &&
6622 ((framesize+1) > info->max_frame_size) ) ||
6623 (framesize > info->max_frame_size) )
6624 info->icount.rxlong++;
6625 else {
6626 /* copy dma buffer(s) to contiguous intermediate buffer */
6627 int copy_count = framesize;
6628 int index = StartIndex;
6629 unsigned char *ptmp = info->intermediate_rxbuffer;
6630
6631 if ( !(status & RXSTATUS_CRC_ERROR))
6632 info->icount.rxok++;
6633
6634 while(copy_count) {
6635 int partial_count;
6636 if ( copy_count > DMABUFFERSIZE )
6637 partial_count = DMABUFFERSIZE;
6638 else
6639 partial_count = copy_count;
6640
6641 pBufEntry = &(info->rx_buffer_list[index]);
6642 memcpy( ptmp, pBufEntry->virt_addr, partial_count );
6643 ptmp += partial_count;
6644 copy_count -= partial_count;
6645
6646 if ( ++index == info->rx_buffer_count )
6647 index = 0;
6648 }
6649
6650 if ( info->params.crc_type & HDLC_CRC_RETURN_EX ) {
6651 ++framesize;
6652 *ptmp = (status & RXSTATUS_CRC_ERROR ?
6653 RX_CRC_ERROR :
6654 RX_OK);
6655
6656 if ( debug_level >= DEBUG_LEVEL_DATA )
6657 printk("%s(%d):mgsl_get_rx_frame(%s) rx frame status=%d\n",
6658 __FILE__,__LINE__,info->device_name,
6659 *ptmp);
6660 }
6661
6662#if SYNCLINK_GENERIC_HDLC
6663 if (info->netcount)
6664 hdlcdev_rx(info,info->intermediate_rxbuffer,framesize);
6665 else
6666#endif
6667 ldisc_receive_buf(tty, info->intermediate_rxbuffer, info->flag_buf, framesize);
6668 }
6669 }
6670 /* Free the buffers used by this frame. */
6671 mgsl_free_rx_frame_buffers( info, StartIndex, EndIndex );
6672
6673 ReturnCode = true;
6674
6675Cleanup:
6676
6677 if ( info->rx_enabled && info->rx_overflow ) {
6678 /* The receiver needs to restarted because of
6679 * a receive overflow (buffer or FIFO). If the
6680 * receive buffers are now empty, then restart receiver.
6681 */
6682
6683 if ( !info->rx_buffer_list[EndIndex].status &&
6684 info->rx_buffer_list[EndIndex].count ) {
6685 spin_lock_irqsave(&info->irq_spinlock,flags);
6686 usc_start_receiver(info);
6687 spin_unlock_irqrestore(&info->irq_spinlock,flags);
6688 }
6689 }
6690
6691 return ReturnCode;
6692
6693} /* end of mgsl_get_rx_frame() */
6694
6695/* mgsl_get_raw_rx_frame()
6696 *
6697 * This function attempts to return a received frame from the
6698 * receive DMA buffers when running in external loop mode. In this mode,
6699 * we will return at most one DMABUFFERSIZE frame to the application.
6700 * The USC receiver is triggering off of DCD going active to start a new
6701 * frame, and DCD going inactive to terminate the frame (similar to
6702 * processing a closing flag character).
6703 *
6704 * In this routine, we will return DMABUFFERSIZE "chunks" at a time.
6705 * If DCD goes inactive, the last Rx DMA Buffer will have a non-zero
6706 * status field and the RCC field will indicate the length of the
6707 * entire received frame. We take this RCC field and get the modulus
6708 * of RCC and DMABUFFERSIZE to determine if number of bytes in the
6709 * last Rx DMA buffer and return that last portion of the frame.
6710 *
6711 * Arguments: info pointer to device extension
6712 * Return Value: true if frame returned, otherwise false
6713 */
6714static bool mgsl_get_raw_rx_frame(struct mgsl_struct *info)
6715{
6716 unsigned int CurrentIndex, NextIndex;
6717 unsigned short status;
6718 DMABUFFERENTRY *pBufEntry;
6719 unsigned int framesize = 0;
6720 bool ReturnCode = false;
6721 unsigned long flags;
6722 struct tty_struct *tty = info->port.tty;
6723
6724 /*
6725 * current_rx_buffer points to the 1st buffer of the next available
6726 * receive frame. The status field is set by the 16C32 after
6727 * completing a receive frame. If the status field of this buffer
6728 * is zero, either the USC is still filling this buffer or this
6729 * is one of a series of buffers making up a received frame.
6730 *
6731 * If the count field of this buffer is zero, the USC is either
6732 * using this buffer or has used this buffer. Look at the count
6733 * field of the next buffer. If that next buffer's count is
6734 * non-zero, the USC is still actively using the current buffer.
6735 * Otherwise, if the next buffer's count field is zero, the
6736 * current buffer is complete and the USC is using the next
6737 * buffer.
6738 */
6739 CurrentIndex = NextIndex = info->current_rx_buffer;
6740 ++NextIndex;
6741 if ( NextIndex == info->rx_buffer_count )
6742 NextIndex = 0;
6743
6744 if ( info->rx_buffer_list[CurrentIndex].status != 0 ||
6745 (info->rx_buffer_list[CurrentIndex].count == 0 &&
6746 info->rx_buffer_list[NextIndex].count == 0)) {
6747 /*
6748 * Either the status field of this dma buffer is non-zero
6749 * (indicating the last buffer of a receive frame) or the next
6750 * buffer is marked as in use -- implying this buffer is complete
6751 * and an intermediate buffer for this received frame.
6752 */
6753
6754 status = info->rx_buffer_list[CurrentIndex].status;
6755
6756 if ( status & (RXSTATUS_SHORT_FRAME + RXSTATUS_OVERRUN +
6757 RXSTATUS_CRC_ERROR + RXSTATUS_ABORT) ) {
6758 if ( status & RXSTATUS_SHORT_FRAME )
6759 info->icount.rxshort++;
6760 else if ( status & RXSTATUS_ABORT )
6761 info->icount.rxabort++;
6762 else if ( status & RXSTATUS_OVERRUN )
6763 info->icount.rxover++;
6764 else
6765 info->icount.rxcrc++;
6766 framesize = 0;
6767 } else {
6768 /*
6769 * A receive frame is available, get frame size and status.
6770 *
6771 * The frame size is the starting value of the RCC (which was
6772 * set to 0xffff) minus the ending value of the RCC (decremented
6773 * once for each receive character) minus 2 or 4 for the 16-bit
6774 * or 32-bit CRC.
6775 *
6776 * If the status field is zero, this is an intermediate buffer.
6777 * It's size is 4K.
6778 *
6779 * If the DMA Buffer Entry's Status field is non-zero, the
6780 * receive operation completed normally (ie: DCD dropped). The
6781 * RCC field is valid and holds the received frame size.
6782 * It is possible that the RCC field will be zero on a DMA buffer
6783 * entry with a non-zero status. This can occur if the total
6784 * frame size (number of bytes between the time DCD goes active
6785 * to the time DCD goes inactive) exceeds 65535 bytes. In this
6786 * case the 16C32 has underrun on the RCC count and appears to
6787 * stop updating this counter to let us know the actual received
6788 * frame size. If this happens (non-zero status and zero RCC),
6789 * simply return the entire RxDMA Buffer
6790 */
6791 if ( status ) {
6792 /*
6793 * In the event that the final RxDMA Buffer is
6794 * terminated with a non-zero status and the RCC
6795 * field is zero, we interpret this as the RCC
6796 * having underflowed (received frame > 65535 bytes).
6797 *
6798 * Signal the event to the user by passing back
6799 * a status of RxStatus_CrcError returning the full
6800 * buffer and let the app figure out what data is
6801 * actually valid
6802 */
6803 if ( info->rx_buffer_list[CurrentIndex].rcc )
6804 framesize = RCLRVALUE - info->rx_buffer_list[CurrentIndex].rcc;
6805 else
6806 framesize = DMABUFFERSIZE;
6807 }
6808 else
6809 framesize = DMABUFFERSIZE;
6810 }
6811
6812 if ( framesize > DMABUFFERSIZE ) {
6813 /*
6814 * if running in raw sync mode, ISR handler for
6815 * End Of Buffer events terminates all buffers at 4K.
6816 * If this frame size is said to be >4K, get the
6817 * actual number of bytes of the frame in this buffer.
6818 */
6819 framesize = framesize % DMABUFFERSIZE;
6820 }
6821
6822
6823 if ( debug_level >= DEBUG_LEVEL_BH )
6824 printk("%s(%d):mgsl_get_raw_rx_frame(%s) status=%04X size=%d\n",
6825 __FILE__,__LINE__,info->device_name,status,framesize);
6826
6827 if ( debug_level >= DEBUG_LEVEL_DATA )
6828 mgsl_trace_block(info,info->rx_buffer_list[CurrentIndex].virt_addr,
6829 min_t(int, framesize, DMABUFFERSIZE),0);
6830
6831 if (framesize) {
6832 /* copy dma buffer(s) to contiguous intermediate buffer */
6833 /* NOTE: we never copy more than DMABUFFERSIZE bytes */
6834
6835 pBufEntry = &(info->rx_buffer_list[CurrentIndex]);
6836 memcpy( info->intermediate_rxbuffer, pBufEntry->virt_addr, framesize);
6837 info->icount.rxok++;
6838
6839 ldisc_receive_buf(tty, info->intermediate_rxbuffer, info->flag_buf, framesize);
6840 }
6841
6842 /* Free the buffers used by this frame. */
6843 mgsl_free_rx_frame_buffers( info, CurrentIndex, CurrentIndex );
6844
6845 ReturnCode = true;
6846 }
6847
6848
6849 if ( info->rx_enabled && info->rx_overflow ) {
6850 /* The receiver needs to restarted because of
6851 * a receive overflow (buffer or FIFO). If the
6852 * receive buffers are now empty, then restart receiver.
6853 */
6854
6855 if ( !info->rx_buffer_list[CurrentIndex].status &&
6856 info->rx_buffer_list[CurrentIndex].count ) {
6857 spin_lock_irqsave(&info->irq_spinlock,flags);
6858 usc_start_receiver(info);
6859 spin_unlock_irqrestore(&info->irq_spinlock,flags);
6860 }
6861 }
6862
6863 return ReturnCode;
6864
6865} /* end of mgsl_get_raw_rx_frame() */
6866
6867/* mgsl_load_tx_dma_buffer()
6868 *
6869 * Load the transmit DMA buffer with the specified data.
6870 *
6871 * Arguments:
6872 *
6873 * info pointer to device extension
6874 * Buffer pointer to buffer containing frame to load
6875 * BufferSize size in bytes of frame in Buffer
6876 *
6877 * Return Value: None
6878 */
6879static void mgsl_load_tx_dma_buffer(struct mgsl_struct *info,
6880 const char *Buffer, unsigned int BufferSize)
6881{
6882 unsigned short Copycount;
6883 unsigned int i = 0;
6884 DMABUFFERENTRY *pBufEntry;
6885
6886 if ( debug_level >= DEBUG_LEVEL_DATA )
6887 mgsl_trace_block(info,Buffer, min_t(int, BufferSize, DMABUFFERSIZE), 1);
6888
6889 if (info->params.flags & HDLC_FLAG_HDLC_LOOPMODE) {
6890 /* set CMR:13 to start transmit when
6891 * next GoAhead (abort) is received
6892 */
6893 info->cmr_value |= BIT13;
6894 }
6895
6896 /* begin loading the frame in the next available tx dma
6897 * buffer, remember it's starting location for setting
6898 * up tx dma operation
6899 */
6900 i = info->current_tx_buffer;
6901 info->start_tx_dma_buffer = i;
6902
6903 /* Setup the status and RCC (Frame Size) fields of the 1st */
6904 /* buffer entry in the transmit DMA buffer list. */
6905
6906 info->tx_buffer_list[i].status = info->cmr_value & 0xf000;
6907 info->tx_buffer_list[i].rcc = BufferSize;
6908 info->tx_buffer_list[i].count = BufferSize;
6909
6910 /* Copy frame data from 1st source buffer to the DMA buffers. */
6911 /* The frame data may span multiple DMA buffers. */
6912
6913 while( BufferSize ){
6914 /* Get a pointer to next DMA buffer entry. */
6915 pBufEntry = &info->tx_buffer_list[i++];
6916
6917 if ( i == info->tx_buffer_count )
6918 i=0;
6919
6920 /* Calculate the number of bytes that can be copied from */
6921 /* the source buffer to this DMA buffer. */
6922 if ( BufferSize > DMABUFFERSIZE )
6923 Copycount = DMABUFFERSIZE;
6924 else
6925 Copycount = BufferSize;
6926
6927 /* Actually copy data from source buffer to DMA buffer. */
6928 /* Also set the data count for this individual DMA buffer. */
6929 if ( info->bus_type == MGSL_BUS_TYPE_PCI )
6930 mgsl_load_pci_memory(pBufEntry->virt_addr, Buffer,Copycount);
6931 else
6932 memcpy(pBufEntry->virt_addr, Buffer, Copycount);
6933
6934 pBufEntry->count = Copycount;
6935
6936 /* Advance source pointer and reduce remaining data count. */
6937 Buffer += Copycount;
6938 BufferSize -= Copycount;
6939
6940 ++info->tx_dma_buffers_used;
6941 }
6942
6943 /* remember next available tx dma buffer */
6944 info->current_tx_buffer = i;
6945
6946} /* end of mgsl_load_tx_dma_buffer() */
6947
6948/*
6949 * mgsl_register_test()
6950 *
6951 * Performs a register test of the 16C32.
6952 *
6953 * Arguments: info pointer to device instance data
6954 * Return Value: true if test passed, otherwise false
6955 */
6956static bool mgsl_register_test( struct mgsl_struct *info )
6957{
6958 static unsigned short BitPatterns[] =
6959 { 0x0000, 0xffff, 0xaaaa, 0x5555, 0x1234, 0x6969, 0x9696, 0x0f0f };
6960 static unsigned int Patterncount = ARRAY_SIZE(BitPatterns);
6961 unsigned int i;
6962 bool rc = true;
6963 unsigned long flags;
6964
6965 spin_lock_irqsave(&info->irq_spinlock,flags);
6966 usc_reset(info);
6967
6968 /* Verify the reset state of some registers. */
6969
6970 if ( (usc_InReg( info, SICR ) != 0) ||
6971 (usc_InReg( info, IVR ) != 0) ||
6972 (usc_InDmaReg( info, DIVR ) != 0) ){
6973 rc = false;
6974 }
6975
6976 if ( rc ){
6977 /* Write bit patterns to various registers but do it out of */
6978 /* sync, then read back and verify values. */
6979
6980 for ( i = 0 ; i < Patterncount ; i++ ) {
6981 usc_OutReg( info, TC0R, BitPatterns[i] );
6982 usc_OutReg( info, TC1R, BitPatterns[(i+1)%Patterncount] );
6983 usc_OutReg( info, TCLR, BitPatterns[(i+2)%Patterncount] );
6984 usc_OutReg( info, RCLR, BitPatterns[(i+3)%Patterncount] );
6985 usc_OutReg( info, RSR, BitPatterns[(i+4)%Patterncount] );
6986 usc_OutDmaReg( info, TBCR, BitPatterns[(i+5)%Patterncount] );
6987
6988 if ( (usc_InReg( info, TC0R ) != BitPatterns[i]) ||
6989 (usc_InReg( info, TC1R ) != BitPatterns[(i+1)%Patterncount]) ||
6990 (usc_InReg( info, TCLR ) != BitPatterns[(i+2)%Patterncount]) ||
6991 (usc_InReg( info, RCLR ) != BitPatterns[(i+3)%Patterncount]) ||
6992 (usc_InReg( info, RSR ) != BitPatterns[(i+4)%Patterncount]) ||
6993 (usc_InDmaReg( info, TBCR ) != BitPatterns[(i+5)%Patterncount]) ){
6994 rc = false;
6995 break;
6996 }
6997 }
6998 }
6999
7000 usc_reset(info);
7001 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7002
7003 return rc;
7004
7005} /* end of mgsl_register_test() */
7006
7007/* mgsl_irq_test() Perform interrupt test of the 16C32.
7008 *
7009 * Arguments: info pointer to device instance data
7010 * Return Value: true if test passed, otherwise false
7011 */
7012static bool mgsl_irq_test( struct mgsl_struct *info )
7013{
7014 unsigned long EndTime;
7015 unsigned long flags;
7016
7017 spin_lock_irqsave(&info->irq_spinlock,flags);
7018 usc_reset(info);
7019
7020 /*
7021 * Setup 16C32 to interrupt on TxC pin (14MHz clock) transition.
7022 * The ISR sets irq_occurred to true.
7023 */
7024
7025 info->irq_occurred = false;
7026
7027 /* Enable INTEN gate for ISA adapter (Port 6, Bit12) */
7028 /* Enable INTEN (Port 6, Bit12) */
7029 /* This connects the IRQ request signal to the ISA bus */
7030 /* on the ISA adapter. This has no effect for the PCI adapter */
7031 usc_OutReg( info, PCR, (unsigned short)((usc_InReg(info, PCR) | BIT13) & ~BIT12) );
7032
7033 usc_EnableMasterIrqBit(info);
7034 usc_EnableInterrupts(info, IO_PIN);
7035 usc_ClearIrqPendingBits(info, IO_PIN);
7036
7037 usc_UnlatchIostatusBits(info, MISCSTATUS_TXC_LATCHED);
7038 usc_EnableStatusIrqs(info, SICR_TXC_ACTIVE + SICR_TXC_INACTIVE);
7039
7040 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7041
7042 EndTime=100;
7043 while( EndTime-- && !info->irq_occurred ) {
7044 msleep_interruptible(10);
7045 }
7046
7047 spin_lock_irqsave(&info->irq_spinlock,flags);
7048 usc_reset(info);
7049 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7050
7051 return info->irq_occurred;
7052
7053} /* end of mgsl_irq_test() */
7054
7055/* mgsl_dma_test()
7056 *
7057 * Perform a DMA test of the 16C32. A small frame is
7058 * transmitted via DMA from a transmit buffer to a receive buffer
7059 * using single buffer DMA mode.
7060 *
7061 * Arguments: info pointer to device instance data
7062 * Return Value: true if test passed, otherwise false
7063 */
7064static bool mgsl_dma_test( struct mgsl_struct *info )
7065{
7066 unsigned short FifoLevel;
7067 unsigned long phys_addr;
7068 unsigned int FrameSize;
7069 unsigned int i;
7070 char *TmpPtr;
7071 bool rc = true;
7072 unsigned short status=0;
7073 unsigned long EndTime;
7074 unsigned long flags;
7075 MGSL_PARAMS tmp_params;
7076
7077 /* save current port options */
7078 memcpy(&tmp_params,&info->params,sizeof(MGSL_PARAMS));
7079 /* load default port options */
7080 memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS));
7081
7082#define TESTFRAMESIZE 40
7083
7084 spin_lock_irqsave(&info->irq_spinlock,flags);
7085
7086 /* setup 16C32 for SDLC DMA transfer mode */
7087
7088 usc_reset(info);
7089 usc_set_sdlc_mode(info);
7090 usc_enable_loopback(info,1);
7091
7092 /* Reprogram the RDMR so that the 16C32 does NOT clear the count
7093 * field of the buffer entry after fetching buffer address. This
7094 * way we can detect a DMA failure for a DMA read (which should be
7095 * non-destructive to system memory) before we try and write to
7096 * memory (where a failure could corrupt system memory).
7097 */
7098
7099 /* Receive DMA mode Register (RDMR)
7100 *
7101 * <15..14> 11 DMA mode = Linked List Buffer mode
7102 * <13> 1 RSBinA/L = store Rx status Block in List entry
7103 * <12> 0 1 = Clear count of List Entry after fetching
7104 * <11..10> 00 Address mode = Increment
7105 * <9> 1 Terminate Buffer on RxBound
7106 * <8> 0 Bus Width = 16bits
7107 * <7..0> ? status Bits (write as 0s)
7108 *
7109 * 1110 0010 0000 0000 = 0xe200
7110 */
7111
7112 usc_OutDmaReg( info, RDMR, 0xe200 );
7113
7114 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7115
7116
7117 /* SETUP TRANSMIT AND RECEIVE DMA BUFFERS */
7118
7119 FrameSize = TESTFRAMESIZE;
7120
7121 /* setup 1st transmit buffer entry: */
7122 /* with frame size and transmit control word */
7123
7124 info->tx_buffer_list[0].count = FrameSize;
7125 info->tx_buffer_list[0].rcc = FrameSize;
7126 info->tx_buffer_list[0].status = 0x4000;
7127
7128 /* build a transmit frame in 1st transmit DMA buffer */
7129
7130 TmpPtr = info->tx_buffer_list[0].virt_addr;
7131 for (i = 0; i < FrameSize; i++ )
7132 *TmpPtr++ = i;
7133
7134 /* setup 1st receive buffer entry: */
7135 /* clear status, set max receive buffer size */
7136
7137 info->rx_buffer_list[0].status = 0;
7138 info->rx_buffer_list[0].count = FrameSize + 4;
7139
7140 /* zero out the 1st receive buffer */
7141
7142 memset( info->rx_buffer_list[0].virt_addr, 0, FrameSize + 4 );
7143
7144 /* Set count field of next buffer entries to prevent */
7145 /* 16C32 from using buffers after the 1st one. */
7146
7147 info->tx_buffer_list[1].count = 0;
7148 info->rx_buffer_list[1].count = 0;
7149
7150
7151 /***************************/
7152 /* Program 16C32 receiver. */
7153 /***************************/
7154
7155 spin_lock_irqsave(&info->irq_spinlock,flags);
7156
7157 /* setup DMA transfers */
7158 usc_RTCmd( info, RTCmd_PurgeRxFifo );
7159
7160 /* program 16C32 receiver with physical address of 1st DMA buffer entry */
7161 phys_addr = info->rx_buffer_list[0].phys_entry;
7162 usc_OutDmaReg( info, NRARL, (unsigned short)phys_addr );
7163 usc_OutDmaReg( info, NRARU, (unsigned short)(phys_addr >> 16) );
7164
7165 /* Clear the Rx DMA status bits (read RDMR) and start channel */
7166 usc_InDmaReg( info, RDMR );
7167 usc_DmaCmd( info, DmaCmd_InitRxChannel );
7168
7169 /* Enable Receiver (RMR <1..0> = 10) */
7170 usc_OutReg( info, RMR, (unsigned short)((usc_InReg(info, RMR) & 0xfffc) | 0x0002) );
7171
7172 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7173
7174
7175 /*************************************************************/
7176 /* WAIT FOR RECEIVER TO DMA ALL PARAMETERS FROM BUFFER ENTRY */
7177 /*************************************************************/
7178
7179 /* Wait 100ms for interrupt. */
7180 EndTime = jiffies + msecs_to_jiffies(100);
7181
7182 for(;;) {
7183 if (time_after(jiffies, EndTime)) {
7184 rc = false;
7185 break;
7186 }
7187
7188 spin_lock_irqsave(&info->irq_spinlock,flags);
7189 status = usc_InDmaReg( info, RDMR );
7190 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7191
7192 if ( !(status & BIT4) && (status & BIT5) ) {
7193 /* INITG (BIT 4) is inactive (no entry read in progress) AND */
7194 /* BUSY (BIT 5) is active (channel still active). */
7195 /* This means the buffer entry read has completed. */
7196 break;
7197 }
7198 }
7199
7200
7201 /******************************/
7202 /* Program 16C32 transmitter. */
7203 /******************************/
7204
7205 spin_lock_irqsave(&info->irq_spinlock,flags);
7206
7207 /* Program the Transmit Character Length Register (TCLR) */
7208 /* and clear FIFO (TCC is loaded with TCLR on FIFO clear) */
7209
7210 usc_OutReg( info, TCLR, (unsigned short)info->tx_buffer_list[0].count );
7211 usc_RTCmd( info, RTCmd_PurgeTxFifo );
7212
7213 /* Program the address of the 1st DMA Buffer Entry in linked list */
7214
7215 phys_addr = info->tx_buffer_list[0].phys_entry;
7216 usc_OutDmaReg( info, NTARL, (unsigned short)phys_addr );
7217 usc_OutDmaReg( info, NTARU, (unsigned short)(phys_addr >> 16) );
7218
7219 /* unlatch Tx status bits, and start transmit channel. */
7220
7221 usc_OutReg( info, TCSR, (unsigned short)(( usc_InReg(info, TCSR) & 0x0f00) | 0xfa) );
7222 usc_DmaCmd( info, DmaCmd_InitTxChannel );
7223
7224 /* wait for DMA controller to fill transmit FIFO */
7225
7226 usc_TCmd( info, TCmd_SelectTicrTxFifostatus );
7227
7228 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7229
7230
7231 /**********************************/
7232 /* WAIT FOR TRANSMIT FIFO TO FILL */
7233 /**********************************/
7234
7235 /* Wait 100ms */
7236 EndTime = jiffies + msecs_to_jiffies(100);
7237
7238 for(;;) {
7239 if (time_after(jiffies, EndTime)) {
7240 rc = false;
7241 break;
7242 }
7243
7244 spin_lock_irqsave(&info->irq_spinlock,flags);
7245 FifoLevel = usc_InReg(info, TICR) >> 8;
7246 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7247
7248 if ( FifoLevel < 16 )
7249 break;
7250 else
7251 if ( FrameSize < 32 ) {
7252 /* This frame is smaller than the entire transmit FIFO */
7253 /* so wait for the entire frame to be loaded. */
7254 if ( FifoLevel <= (32 - FrameSize) )
7255 break;
7256 }
7257 }
7258
7259
7260 if ( rc )
7261 {
7262 /* Enable 16C32 transmitter. */
7263
7264 spin_lock_irqsave(&info->irq_spinlock,flags);
7265
7266 /* Transmit mode Register (TMR), <1..0> = 10, Enable Transmitter */
7267 usc_TCmd( info, TCmd_SendFrame );
7268 usc_OutReg( info, TMR, (unsigned short)((usc_InReg(info, TMR) & 0xfffc) | 0x0002) );
7269
7270 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7271
7272
7273 /******************************/
7274 /* WAIT FOR TRANSMIT COMPLETE */
7275 /******************************/
7276
7277 /* Wait 100ms */
7278 EndTime = jiffies + msecs_to_jiffies(100);
7279
7280 /* While timer not expired wait for transmit complete */
7281
7282 spin_lock_irqsave(&info->irq_spinlock,flags);
7283 status = usc_InReg( info, TCSR );
7284 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7285
7286 while ( !(status & (BIT6+BIT5+BIT4+BIT2+BIT1)) ) {
7287 if (time_after(jiffies, EndTime)) {
7288 rc = false;
7289 break;
7290 }
7291
7292 spin_lock_irqsave(&info->irq_spinlock,flags);
7293 status = usc_InReg( info, TCSR );
7294 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7295 }
7296 }
7297
7298
7299 if ( rc ){
7300 /* CHECK FOR TRANSMIT ERRORS */
7301 if ( status & (BIT5 + BIT1) )
7302 rc = false;
7303 }
7304
7305 if ( rc ) {
7306 /* WAIT FOR RECEIVE COMPLETE */
7307
7308 /* Wait 100ms */
7309 EndTime = jiffies + msecs_to_jiffies(100);
7310
7311 /* Wait for 16C32 to write receive status to buffer entry. */
7312 status=info->rx_buffer_list[0].status;
7313 while ( status == 0 ) {
7314 if (time_after(jiffies, EndTime)) {
7315 rc = false;
7316 break;
7317 }
7318 status=info->rx_buffer_list[0].status;
7319 }
7320 }
7321
7322
7323 if ( rc ) {
7324 /* CHECK FOR RECEIVE ERRORS */
7325 status = info->rx_buffer_list[0].status;
7326
7327 if ( status & (BIT8 + BIT3 + BIT1) ) {
7328 /* receive error has occurred */
7329 rc = false;
7330 } else {
7331 if ( memcmp( info->tx_buffer_list[0].virt_addr ,
7332 info->rx_buffer_list[0].virt_addr, FrameSize ) ){
7333 rc = false;
7334 }
7335 }
7336 }
7337
7338 spin_lock_irqsave(&info->irq_spinlock,flags);
7339 usc_reset( info );
7340 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7341
7342 /* restore current port options */
7343 memcpy(&info->params,&tmp_params,sizeof(MGSL_PARAMS));
7344
7345 return rc;
7346
7347} /* end of mgsl_dma_test() */
7348
7349/* mgsl_adapter_test()
7350 *
7351 * Perform the register, IRQ, and DMA tests for the 16C32.
7352 *
7353 * Arguments: info pointer to device instance data
7354 * Return Value: 0 if success, otherwise -ENODEV
7355 */
7356static int mgsl_adapter_test( struct mgsl_struct *info )
7357{
7358 if ( debug_level >= DEBUG_LEVEL_INFO )
7359 printk( "%s(%d):Testing device %s\n",
7360 __FILE__,__LINE__,info->device_name );
7361
7362 if ( !mgsl_register_test( info ) ) {
7363 info->init_error = DiagStatus_AddressFailure;
7364 printk( "%s(%d):Register test failure for device %s Addr=%04X\n",
7365 __FILE__,__LINE__,info->device_name, (unsigned short)(info->io_base) );
7366 return -ENODEV;
7367 }
7368
7369 if ( !mgsl_irq_test( info ) ) {
7370 info->init_error = DiagStatus_IrqFailure;
7371 printk( "%s(%d):Interrupt test failure for device %s IRQ=%d\n",
7372 __FILE__,__LINE__,info->device_name, (unsigned short)(info->irq_level) );
7373 return -ENODEV;
7374 }
7375
7376 if ( !mgsl_dma_test( info ) ) {
7377 info->init_error = DiagStatus_DmaFailure;
7378 printk( "%s(%d):DMA test failure for device %s DMA=%d\n",
7379 __FILE__,__LINE__,info->device_name, (unsigned short)(info->dma_level) );
7380 return -ENODEV;
7381 }
7382
7383 if ( debug_level >= DEBUG_LEVEL_INFO )
7384 printk( "%s(%d):device %s passed diagnostics\n",
7385 __FILE__,__LINE__,info->device_name );
7386
7387 return 0;
7388
7389} /* end of mgsl_adapter_test() */
7390
7391/* mgsl_memory_test()
7392 *
7393 * Test the shared memory on a PCI adapter.
7394 *
7395 * Arguments: info pointer to device instance data
7396 * Return Value: true if test passed, otherwise false
7397 */
7398static bool mgsl_memory_test( struct mgsl_struct *info )
7399{
7400 static unsigned long BitPatterns[] =
7401 { 0x0, 0x55555555, 0xaaaaaaaa, 0x66666666, 0x99999999, 0xffffffff, 0x12345678 };
7402 unsigned long Patterncount = ARRAY_SIZE(BitPatterns);
7403 unsigned long i;
7404 unsigned long TestLimit = SHARED_MEM_ADDRESS_SIZE/sizeof(unsigned long);
7405 unsigned long * TestAddr;
7406
7407 if ( info->bus_type != MGSL_BUS_TYPE_PCI )
7408 return true;
7409
7410 TestAddr = (unsigned long *)info->memory_base;
7411
7412 /* Test data lines with test pattern at one location. */
7413
7414 for ( i = 0 ; i < Patterncount ; i++ ) {
7415 *TestAddr = BitPatterns[i];
7416 if ( *TestAddr != BitPatterns[i] )
7417 return false;
7418 }
7419
7420 /* Test address lines with incrementing pattern over */
7421 /* entire address range. */
7422
7423 for ( i = 0 ; i < TestLimit ; i++ ) {
7424 *TestAddr = i * 4;
7425 TestAddr++;
7426 }
7427
7428 TestAddr = (unsigned long *)info->memory_base;
7429
7430 for ( i = 0 ; i < TestLimit ; i++ ) {
7431 if ( *TestAddr != i * 4 )
7432 return false;
7433 TestAddr++;
7434 }
7435
7436 memset( info->memory_base, 0, SHARED_MEM_ADDRESS_SIZE );
7437
7438 return true;
7439
7440} /* End Of mgsl_memory_test() */
7441
7442
7443/* mgsl_load_pci_memory()
7444 *
7445 * Load a large block of data into the PCI shared memory.
7446 * Use this instead of memcpy() or memmove() to move data
7447 * into the PCI shared memory.
7448 *
7449 * Notes:
7450 *
7451 * This function prevents the PCI9050 interface chip from hogging
7452 * the adapter local bus, which can starve the 16C32 by preventing
7453 * 16C32 bus master cycles.
7454 *
7455 * The PCI9050 documentation says that the 9050 will always release
7456 * control of the local bus after completing the current read
7457 * or write operation.
7458 *
7459 * It appears that as long as the PCI9050 write FIFO is full, the
7460 * PCI9050 treats all of the writes as a single burst transaction
7461 * and will not release the bus. This causes DMA latency problems
7462 * at high speeds when copying large data blocks to the shared
7463 * memory.
7464 *
7465 * This function in effect, breaks the a large shared memory write
7466 * into multiple transations by interleaving a shared memory read
7467 * which will flush the write FIFO and 'complete' the write
7468 * transation. This allows any pending DMA request to gain control
7469 * of the local bus in a timely fasion.
7470 *
7471 * Arguments:
7472 *
7473 * TargetPtr pointer to target address in PCI shared memory
7474 * SourcePtr pointer to source buffer for data
7475 * count count in bytes of data to copy
7476 *
7477 * Return Value: None
7478 */
7479static void mgsl_load_pci_memory( char* TargetPtr, const char* SourcePtr,
7480 unsigned short count )
7481{
7482 /* 16 32-bit writes @ 60ns each = 960ns max latency on local bus */
7483#define PCI_LOAD_INTERVAL 64
7484
7485 unsigned short Intervalcount = count / PCI_LOAD_INTERVAL;
7486 unsigned short Index;
7487 unsigned long Dummy;
7488
7489 for ( Index = 0 ; Index < Intervalcount ; Index++ )
7490 {
7491 memcpy(TargetPtr, SourcePtr, PCI_LOAD_INTERVAL);
7492 Dummy = *((volatile unsigned long *)TargetPtr);
7493 TargetPtr += PCI_LOAD_INTERVAL;
7494 SourcePtr += PCI_LOAD_INTERVAL;
7495 }
7496
7497 memcpy( TargetPtr, SourcePtr, count % PCI_LOAD_INTERVAL );
7498
7499} /* End Of mgsl_load_pci_memory() */
7500
7501static void mgsl_trace_block(struct mgsl_struct *info,const char* data, int count, int xmit)
7502{
7503 int i;
7504 int linecount;
7505 if (xmit)
7506 printk("%s tx data:\n",info->device_name);
7507 else
7508 printk("%s rx data:\n",info->device_name);
7509
7510 while(count) {
7511 if (count > 16)
7512 linecount = 16;
7513 else
7514 linecount = count;
7515
7516 for(i=0;i<linecount;i++)
7517 printk("%02X ",(unsigned char)data[i]);
7518 for(;i<17;i++)
7519 printk(" ");
7520 for(i=0;i<linecount;i++) {
7521 if (data[i]>=040 && data[i]<=0176)
7522 printk("%c",data[i]);
7523 else
7524 printk(".");
7525 }
7526 printk("\n");
7527
7528 data += linecount;
7529 count -= linecount;
7530 }
7531} /* end of mgsl_trace_block() */
7532
7533/* mgsl_tx_timeout()
7534 *
7535 * called when HDLC frame times out
7536 * update stats and do tx completion processing
7537 *
7538 * Arguments: context pointer to device instance data
7539 * Return Value: None
7540 */
7541static void mgsl_tx_timeout(unsigned long context)
7542{
7543 struct mgsl_struct *info = (struct mgsl_struct*)context;
7544 unsigned long flags;
7545
7546 if ( debug_level >= DEBUG_LEVEL_INFO )
7547 printk( "%s(%d):mgsl_tx_timeout(%s)\n",
7548 __FILE__,__LINE__,info->device_name);
7549 if(info->tx_active &&
7550 (info->params.mode == MGSL_MODE_HDLC ||
7551 info->params.mode == MGSL_MODE_RAW) ) {
7552 info->icount.txtimeout++;
7553 }
7554 spin_lock_irqsave(&info->irq_spinlock,flags);
7555 info->tx_active = false;
7556 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
7557
7558 if ( info->params.flags & HDLC_FLAG_HDLC_LOOPMODE )
7559 usc_loopmode_cancel_transmit( info );
7560
7561 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7562
7563#if SYNCLINK_GENERIC_HDLC
7564 if (info->netcount)
7565 hdlcdev_tx_done(info);
7566 else
7567#endif
7568 mgsl_bh_transmit(info);
7569
7570} /* end of mgsl_tx_timeout() */
7571
7572/* signal that there are no more frames to send, so that
7573 * line is 'released' by echoing RxD to TxD when current
7574 * transmission is complete (or immediately if no tx in progress).
7575 */
7576static int mgsl_loopmode_send_done( struct mgsl_struct * info )
7577{
7578 unsigned long flags;
7579
7580 spin_lock_irqsave(&info->irq_spinlock,flags);
7581 if (info->params.flags & HDLC_FLAG_HDLC_LOOPMODE) {
7582 if (info->tx_active)
7583 info->loopmode_send_done_requested = true;
7584 else
7585 usc_loopmode_send_done(info);
7586 }
7587 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7588
7589 return 0;
7590}
7591
7592/* release the line by echoing RxD to TxD
7593 * upon completion of a transmit frame
7594 */
7595static void usc_loopmode_send_done( struct mgsl_struct * info )
7596{
7597 info->loopmode_send_done_requested = false;
7598 /* clear CMR:13 to 0 to start echoing RxData to TxData */
7599 info->cmr_value &= ~BIT13;
7600 usc_OutReg(info, CMR, info->cmr_value);
7601}
7602
7603/* abort a transmit in progress while in HDLC LoopMode
7604 */
7605static void usc_loopmode_cancel_transmit( struct mgsl_struct * info )
7606{
7607 /* reset tx dma channel and purge TxFifo */
7608 usc_RTCmd( info, RTCmd_PurgeTxFifo );
7609 usc_DmaCmd( info, DmaCmd_ResetTxChannel );
7610 usc_loopmode_send_done( info );
7611}
7612
7613/* for HDLC/SDLC LoopMode, setting CMR:13 after the transmitter is enabled
7614 * is an Insert Into Loop action. Upon receipt of a GoAhead sequence (RxAbort)
7615 * we must clear CMR:13 to begin repeating TxData to RxData
7616 */
7617static void usc_loopmode_insert_request( struct mgsl_struct * info )
7618{
7619 info->loopmode_insert_requested = true;
7620
7621 /* enable RxAbort irq. On next RxAbort, clear CMR:13 to
7622 * begin repeating TxData on RxData (complete insertion)
7623 */
7624 usc_OutReg( info, RICR,
7625 (usc_InReg( info, RICR ) | RXSTATUS_ABORT_RECEIVED ) );
7626
7627 /* set CMR:13 to insert into loop on next GoAhead (RxAbort) */
7628 info->cmr_value |= BIT13;
7629 usc_OutReg(info, CMR, info->cmr_value);
7630}
7631
7632/* return 1 if station is inserted into the loop, otherwise 0
7633 */
7634static int usc_loopmode_active( struct mgsl_struct * info)
7635{
7636 return usc_InReg( info, CCSR ) & BIT7 ? 1 : 0 ;
7637}
7638
7639#if SYNCLINK_GENERIC_HDLC
7640
7641/**
7642 * called by generic HDLC layer when protocol selected (PPP, frame relay, etc.)
7643 * set encoding and frame check sequence (FCS) options
7644 *
7645 * dev pointer to network device structure
7646 * encoding serial encoding setting
7647 * parity FCS setting
7648 *
7649 * returns 0 if success, otherwise error code
7650 */
7651static int hdlcdev_attach(struct net_device *dev, unsigned short encoding,
7652 unsigned short parity)
7653{
7654 struct mgsl_struct *info = dev_to_port(dev);
7655 unsigned char new_encoding;
7656 unsigned short new_crctype;
7657
7658 /* return error if TTY interface open */
7659 if (info->port.count)
7660 return -EBUSY;
7661
7662 switch (encoding)
7663 {
7664 case ENCODING_NRZ: new_encoding = HDLC_ENCODING_NRZ; break;
7665 case ENCODING_NRZI: new_encoding = HDLC_ENCODING_NRZI_SPACE; break;
7666 case ENCODING_FM_MARK: new_encoding = HDLC_ENCODING_BIPHASE_MARK; break;
7667 case ENCODING_FM_SPACE: new_encoding = HDLC_ENCODING_BIPHASE_SPACE; break;
7668 case ENCODING_MANCHESTER: new_encoding = HDLC_ENCODING_BIPHASE_LEVEL; break;
7669 default: return -EINVAL;
7670 }
7671
7672 switch (parity)
7673 {
7674 case PARITY_NONE: new_crctype = HDLC_CRC_NONE; break;
7675 case PARITY_CRC16_PR1_CCITT: new_crctype = HDLC_CRC_16_CCITT; break;
7676 case PARITY_CRC32_PR1_CCITT: new_crctype = HDLC_CRC_32_CCITT; break;
7677 default: return -EINVAL;
7678 }
7679
7680 info->params.encoding = new_encoding;
7681 info->params.crc_type = new_crctype;
7682
7683 /* if network interface up, reprogram hardware */
7684 if (info->netcount)
7685 mgsl_program_hw(info);
7686
7687 return 0;
7688}
7689
7690/**
7691 * called by generic HDLC layer to send frame
7692 *
7693 * skb socket buffer containing HDLC frame
7694 * dev pointer to network device structure
7695 */
7696static netdev_tx_t hdlcdev_xmit(struct sk_buff *skb,
7697 struct net_device *dev)
7698{
7699 struct mgsl_struct *info = dev_to_port(dev);
7700 unsigned long flags;
7701
7702 if (debug_level >= DEBUG_LEVEL_INFO)
7703 printk(KERN_INFO "%s:hdlc_xmit(%s)\n",__FILE__,dev->name);
7704
7705 /* stop sending until this frame completes */
7706 netif_stop_queue(dev);
7707
7708 /* copy data to device buffers */
7709 info->xmit_cnt = skb->len;
7710 mgsl_load_tx_dma_buffer(info, skb->data, skb->len);
7711
7712 /* update network statistics */
7713 dev->stats.tx_packets++;
7714 dev->stats.tx_bytes += skb->len;
7715
7716 /* done with socket buffer, so free it */
7717 dev_kfree_skb(skb);
7718
7719 /* save start time for transmit timeout detection */
7720 dev->trans_start = jiffies;
7721
7722 /* start hardware transmitter if necessary */
7723 spin_lock_irqsave(&info->irq_spinlock,flags);
7724 if (!info->tx_active)
7725 usc_start_transmitter(info);
7726 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7727
7728 return NETDEV_TX_OK;
7729}
7730
7731/**
7732 * called by network layer when interface enabled
7733 * claim resources and initialize hardware
7734 *
7735 * dev pointer to network device structure
7736 *
7737 * returns 0 if success, otherwise error code
7738 */
7739static int hdlcdev_open(struct net_device *dev)
7740{
7741 struct mgsl_struct *info = dev_to_port(dev);
7742 int rc;
7743 unsigned long flags;
7744
7745 if (debug_level >= DEBUG_LEVEL_INFO)
7746 printk("%s:hdlcdev_open(%s)\n",__FILE__,dev->name);
7747
7748 /* generic HDLC layer open processing */
7749 if ((rc = hdlc_open(dev)))
7750 return rc;
7751
7752 /* arbitrate between network and tty opens */
7753 spin_lock_irqsave(&info->netlock, flags);
7754 if (info->port.count != 0 || info->netcount != 0) {
7755 printk(KERN_WARNING "%s: hdlc_open returning busy\n", dev->name);
7756 spin_unlock_irqrestore(&info->netlock, flags);
7757 return -EBUSY;
7758 }
7759 info->netcount=1;
7760 spin_unlock_irqrestore(&info->netlock, flags);
7761
7762 /* claim resources and init adapter */
7763 if ((rc = startup(info)) != 0) {
7764 spin_lock_irqsave(&info->netlock, flags);
7765 info->netcount=0;
7766 spin_unlock_irqrestore(&info->netlock, flags);
7767 return rc;
7768 }
7769
7770 /* assert DTR and RTS, apply hardware settings */
7771 info->serial_signals |= SerialSignal_RTS + SerialSignal_DTR;
7772 mgsl_program_hw(info);
7773
7774 /* enable network layer transmit */
7775 dev->trans_start = jiffies;
7776 netif_start_queue(dev);
7777
7778 /* inform generic HDLC layer of current DCD status */
7779 spin_lock_irqsave(&info->irq_spinlock, flags);
7780 usc_get_serial_signals(info);
7781 spin_unlock_irqrestore(&info->irq_spinlock, flags);
7782 if (info->serial_signals & SerialSignal_DCD)
7783 netif_carrier_on(dev);
7784 else
7785 netif_carrier_off(dev);
7786 return 0;
7787}
7788
7789/**
7790 * called by network layer when interface is disabled
7791 * shutdown hardware and release resources
7792 *
7793 * dev pointer to network device structure
7794 *
7795 * returns 0 if success, otherwise error code
7796 */
7797static int hdlcdev_close(struct net_device *dev)
7798{
7799 struct mgsl_struct *info = dev_to_port(dev);
7800 unsigned long flags;
7801
7802 if (debug_level >= DEBUG_LEVEL_INFO)
7803 printk("%s:hdlcdev_close(%s)\n",__FILE__,dev->name);
7804
7805 netif_stop_queue(dev);
7806
7807 /* shutdown adapter and release resources */
7808 shutdown(info);
7809
7810 hdlc_close(dev);
7811
7812 spin_lock_irqsave(&info->netlock, flags);
7813 info->netcount=0;
7814 spin_unlock_irqrestore(&info->netlock, flags);
7815
7816 return 0;
7817}
7818
7819/**
7820 * called by network layer to process IOCTL call to network device
7821 *
7822 * dev pointer to network device structure
7823 * ifr pointer to network interface request structure
7824 * cmd IOCTL command code
7825 *
7826 * returns 0 if success, otherwise error code
7827 */
7828static int hdlcdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
7829{
7830 const size_t size = sizeof(sync_serial_settings);
7831 sync_serial_settings new_line;
7832 sync_serial_settings __user *line = ifr->ifr_settings.ifs_ifsu.sync;
7833 struct mgsl_struct *info = dev_to_port(dev);
7834 unsigned int flags;
7835
7836 if (debug_level >= DEBUG_LEVEL_INFO)
7837 printk("%s:hdlcdev_ioctl(%s)\n",__FILE__,dev->name);
7838
7839 /* return error if TTY interface open */
7840 if (info->port.count)
7841 return -EBUSY;
7842
7843 if (cmd != SIOCWANDEV)
7844 return hdlc_ioctl(dev, ifr, cmd);
7845
7846 switch(ifr->ifr_settings.type) {
7847 case IF_GET_IFACE: /* return current sync_serial_settings */
7848
7849 ifr->ifr_settings.type = IF_IFACE_SYNC_SERIAL;
7850 if (ifr->ifr_settings.size < size) {
7851 ifr->ifr_settings.size = size; /* data size wanted */
7852 return -ENOBUFS;
7853 }
7854
7855 flags = info->params.flags & (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
7856 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
7857 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
7858 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN);
7859
7860 switch (flags){
7861 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN): new_line.clock_type = CLOCK_EXT; break;
7862 case (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG): new_line.clock_type = CLOCK_INT; break;
7863 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG): new_line.clock_type = CLOCK_TXINT; break;
7864 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN): new_line.clock_type = CLOCK_TXFROMRX; break;
7865 default: new_line.clock_type = CLOCK_DEFAULT;
7866 }
7867
7868 new_line.clock_rate = info->params.clock_speed;
7869 new_line.loopback = info->params.loopback ? 1:0;
7870
7871 if (copy_to_user(line, &new_line, size))
7872 return -EFAULT;
7873 return 0;
7874
7875 case IF_IFACE_SYNC_SERIAL: /* set sync_serial_settings */
7876
7877 if(!capable(CAP_NET_ADMIN))
7878 return -EPERM;
7879 if (copy_from_user(&new_line, line, size))
7880 return -EFAULT;
7881
7882 switch (new_line.clock_type)
7883 {
7884 case CLOCK_EXT: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN; break;
7885 case CLOCK_TXFROMRX: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN; break;
7886 case CLOCK_INT: flags = HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG; break;
7887 case CLOCK_TXINT: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG; break;
7888 case CLOCK_DEFAULT: flags = info->params.flags &
7889 (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
7890 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
7891 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
7892 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN); break;
7893 default: return -EINVAL;
7894 }
7895
7896 if (new_line.loopback != 0 && new_line.loopback != 1)
7897 return -EINVAL;
7898
7899 info->params.flags &= ~(HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
7900 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
7901 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
7902 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN);
7903 info->params.flags |= flags;
7904
7905 info->params.loopback = new_line.loopback;
7906
7907 if (flags & (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG))
7908 info->params.clock_speed = new_line.clock_rate;
7909 else
7910 info->params.clock_speed = 0;
7911
7912 /* if network interface up, reprogram hardware */
7913 if (info->netcount)
7914 mgsl_program_hw(info);
7915 return 0;
7916
7917 default:
7918 return hdlc_ioctl(dev, ifr, cmd);
7919 }
7920}
7921
7922/**
7923 * called by network layer when transmit timeout is detected
7924 *
7925 * dev pointer to network device structure
7926 */
7927static void hdlcdev_tx_timeout(struct net_device *dev)
7928{
7929 struct mgsl_struct *info = dev_to_port(dev);
7930 unsigned long flags;
7931
7932 if (debug_level >= DEBUG_LEVEL_INFO)
7933 printk("hdlcdev_tx_timeout(%s)\n",dev->name);
7934
7935 dev->stats.tx_errors++;
7936 dev->stats.tx_aborted_errors++;
7937
7938 spin_lock_irqsave(&info->irq_spinlock,flags);
7939 usc_stop_transmitter(info);
7940 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7941
7942 netif_wake_queue(dev);
7943}
7944
7945/**
7946 * called by device driver when transmit completes
7947 * reenable network layer transmit if stopped
7948 *
7949 * info pointer to device instance information
7950 */
7951static void hdlcdev_tx_done(struct mgsl_struct *info)
7952{
7953 if (netif_queue_stopped(info->netdev))
7954 netif_wake_queue(info->netdev);
7955}
7956
7957/**
7958 * called by device driver when frame received
7959 * pass frame to network layer
7960 *
7961 * info pointer to device instance information
7962 * buf pointer to buffer contianing frame data
7963 * size count of data bytes in buf
7964 */
7965static void hdlcdev_rx(struct mgsl_struct *info, char *buf, int size)
7966{
7967 struct sk_buff *skb = dev_alloc_skb(size);
7968 struct net_device *dev = info->netdev;
7969
7970 if (debug_level >= DEBUG_LEVEL_INFO)
7971 printk("hdlcdev_rx(%s)\n", dev->name);
7972
7973 if (skb == NULL) {
7974 printk(KERN_NOTICE "%s: can't alloc skb, dropping packet\n",
7975 dev->name);
7976 dev->stats.rx_dropped++;
7977 return;
7978 }
7979
7980 memcpy(skb_put(skb, size), buf, size);
7981
7982 skb->protocol = hdlc_type_trans(skb, dev);
7983
7984 dev->stats.rx_packets++;
7985 dev->stats.rx_bytes += size;
7986
7987 netif_rx(skb);
7988}
7989
7990static const struct net_device_ops hdlcdev_ops = {
7991 .ndo_open = hdlcdev_open,
7992 .ndo_stop = hdlcdev_close,
7993 .ndo_change_mtu = hdlc_change_mtu,
7994 .ndo_start_xmit = hdlc_start_xmit,
7995 .ndo_do_ioctl = hdlcdev_ioctl,
7996 .ndo_tx_timeout = hdlcdev_tx_timeout,
7997};
7998
7999/**
8000 * called by device driver when adding device instance
8001 * do generic HDLC initialization
8002 *
8003 * info pointer to device instance information
8004 *
8005 * returns 0 if success, otherwise error code
8006 */
8007static int hdlcdev_init(struct mgsl_struct *info)
8008{
8009 int rc;
8010 struct net_device *dev;
8011 hdlc_device *hdlc;
8012
8013 /* allocate and initialize network and HDLC layer objects */
8014
8015 if (!(dev = alloc_hdlcdev(info))) {
8016 printk(KERN_ERR "%s:hdlc device allocation failure\n",__FILE__);
8017 return -ENOMEM;
8018 }
8019
8020 /* for network layer reporting purposes only */
8021 dev->base_addr = info->io_base;
8022 dev->irq = info->irq_level;
8023 dev->dma = info->dma_level;
8024
8025 /* network layer callbacks and settings */
8026 dev->netdev_ops = &hdlcdev_ops;
8027 dev->watchdog_timeo = 10 * HZ;
8028 dev->tx_queue_len = 50;
8029
8030 /* generic HDLC layer callbacks and settings */
8031 hdlc = dev_to_hdlc(dev);
8032 hdlc->attach = hdlcdev_attach;
8033 hdlc->xmit = hdlcdev_xmit;
8034
8035 /* register objects with HDLC layer */
8036 if ((rc = register_hdlc_device(dev))) {
8037 printk(KERN_WARNING "%s:unable to register hdlc device\n",__FILE__);
8038 free_netdev(dev);
8039 return rc;
8040 }
8041
8042 info->netdev = dev;
8043 return 0;
8044}
8045
8046/**
8047 * called by device driver when removing device instance
8048 * do generic HDLC cleanup
8049 *
8050 * info pointer to device instance information
8051 */
8052static void hdlcdev_exit(struct mgsl_struct *info)
8053{
8054 unregister_hdlc_device(info->netdev);
8055 free_netdev(info->netdev);
8056 info->netdev = NULL;
8057}
8058
8059#endif /* CONFIG_HDLC */
8060
8061
8062static int __devinit synclink_init_one (struct pci_dev *dev,
8063 const struct pci_device_id *ent)
8064{
8065 struct mgsl_struct *info;
8066
8067 if (pci_enable_device(dev)) {
8068 printk("error enabling pci device %p\n", dev);
8069 return -EIO;
8070 }
8071
8072 if (!(info = mgsl_allocate_device())) {
8073 printk("can't allocate device instance data.\n");
8074 return -EIO;
8075 }
8076
8077 /* Copy user configuration info to device instance data */
8078
8079 info->io_base = pci_resource_start(dev, 2);
8080 info->irq_level = dev->irq;
8081 info->phys_memory_base = pci_resource_start(dev, 3);
8082
8083 /* Because veremap only works on page boundaries we must map
8084 * a larger area than is actually implemented for the LCR
8085 * memory range. We map a full page starting at the page boundary.
8086 */
8087 info->phys_lcr_base = pci_resource_start(dev, 0);
8088 info->lcr_offset = info->phys_lcr_base & (PAGE_SIZE-1);
8089 info->phys_lcr_base &= ~(PAGE_SIZE-1);
8090
8091 info->bus_type = MGSL_BUS_TYPE_PCI;
8092 info->io_addr_size = 8;
8093 info->irq_flags = IRQF_SHARED;
8094
8095 if (dev->device == 0x0210) {
8096 /* Version 1 PCI9030 based universal PCI adapter */
8097 info->misc_ctrl_value = 0x007c4080;
8098 info->hw_version = 1;
8099 } else {
8100 /* Version 0 PCI9050 based 5V PCI adapter
8101 * A PCI9050 bug prevents reading LCR registers if
8102 * LCR base address bit 7 is set. Maintain shadow
8103 * value so we can write to LCR misc control reg.
8104 */
8105 info->misc_ctrl_value = 0x087e4546;
8106 info->hw_version = 0;
8107 }
8108
8109 mgsl_add_device(info);
8110
8111 return 0;
8112}
8113
8114static void __devexit synclink_remove_one (struct pci_dev *dev)
8115{
8116}
8117
1// SPDX-License-Identifier: GPL-1.0+
2/*
3 * $Id: synclink.c,v 4.38 2005/11/07 16:30:34 paulkf Exp $
4 *
5 * Device driver for Microgate SyncLink ISA and PCI
6 * high speed multiprotocol serial adapters.
7 *
8 * written by Paul Fulghum for Microgate Corporation
9 * paulkf@microgate.com
10 *
11 * Microgate and SyncLink are trademarks of Microgate Corporation
12 *
13 * Derived from serial.c written by Theodore Ts'o and Linus Torvalds
14 *
15 * Original release 01/11/99
16 *
17 * This driver is primarily intended for use in synchronous
18 * HDLC mode. Asynchronous mode is also provided.
19 *
20 * When operating in synchronous mode, each call to mgsl_write()
21 * contains exactly one complete HDLC frame. Calling mgsl_put_char
22 * will start assembling an HDLC frame that will not be sent until
23 * mgsl_flush_chars or mgsl_write is called.
24 *
25 * Synchronous receive data is reported as complete frames. To accomplish
26 * this, the TTY flip buffer is bypassed (too small to hold largest
27 * frame and may fragment frames) and the line discipline
28 * receive entry point is called directly.
29 *
30 * This driver has been tested with a slightly modified ppp.c driver
31 * for synchronous PPP.
32 *
33 * 2000/02/16
34 * Added interface for syncppp.c driver (an alternate synchronous PPP
35 * implementation that also supports Cisco HDLC). Each device instance
36 * registers as a tty device AND a network device (if dosyncppp option
37 * is set for the device). The functionality is determined by which
38 * device interface is opened.
39 *
40 * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
41 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
42 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
43 * DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
44 * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
45 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
46 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
47 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
48 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
49 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
50 * OF THE POSSIBILITY OF SUCH DAMAGE.
51 */
52
53#if defined(__i386__)
54# define BREAKPOINT() asm(" int $3");
55#else
56# define BREAKPOINT() { }
57#endif
58
59#define MAX_ISA_DEVICES 10
60#define MAX_PCI_DEVICES 10
61#define MAX_TOTAL_DEVICES 20
62
63#include <linux/module.h>
64#include <linux/errno.h>
65#include <linux/signal.h>
66#include <linux/sched.h>
67#include <linux/timer.h>
68#include <linux/interrupt.h>
69#include <linux/pci.h>
70#include <linux/tty.h>
71#include <linux/tty_flip.h>
72#include <linux/serial.h>
73#include <linux/major.h>
74#include <linux/string.h>
75#include <linux/fcntl.h>
76#include <linux/ptrace.h>
77#include <linux/ioport.h>
78#include <linux/mm.h>
79#include <linux/seq_file.h>
80#include <linux/slab.h>
81#include <linux/delay.h>
82#include <linux/netdevice.h>
83#include <linux/vmalloc.h>
84#include <linux/init.h>
85#include <linux/ioctl.h>
86#include <linux/synclink.h>
87
88#include <asm/io.h>
89#include <asm/irq.h>
90#include <asm/dma.h>
91#include <linux/bitops.h>
92#include <asm/types.h>
93#include <linux/termios.h>
94#include <linux/workqueue.h>
95#include <linux/hdlc.h>
96#include <linux/dma-mapping.h>
97
98#if defined(CONFIG_HDLC) || (defined(CONFIG_HDLC_MODULE) && defined(CONFIG_SYNCLINK_MODULE))
99#define SYNCLINK_GENERIC_HDLC 1
100#else
101#define SYNCLINK_GENERIC_HDLC 0
102#endif
103
104#define GET_USER(error,value,addr) error = get_user(value,addr)
105#define COPY_FROM_USER(error,dest,src,size) error = copy_from_user(dest,src,size) ? -EFAULT : 0
106#define PUT_USER(error,value,addr) error = put_user(value,addr)
107#define COPY_TO_USER(error,dest,src,size) error = copy_to_user(dest,src,size) ? -EFAULT : 0
108
109#include <linux/uaccess.h>
110
111#define RCLRVALUE 0xffff
112
113static MGSL_PARAMS default_params = {
114 MGSL_MODE_HDLC, /* unsigned long mode */
115 0, /* unsigned char loopback; */
116 HDLC_FLAG_UNDERRUN_ABORT15, /* unsigned short flags; */
117 HDLC_ENCODING_NRZI_SPACE, /* unsigned char encoding; */
118 0, /* unsigned long clock_speed; */
119 0xff, /* unsigned char addr_filter; */
120 HDLC_CRC_16_CCITT, /* unsigned short crc_type; */
121 HDLC_PREAMBLE_LENGTH_8BITS, /* unsigned char preamble_length; */
122 HDLC_PREAMBLE_PATTERN_NONE, /* unsigned char preamble; */
123 9600, /* unsigned long data_rate; */
124 8, /* unsigned char data_bits; */
125 1, /* unsigned char stop_bits; */
126 ASYNC_PARITY_NONE /* unsigned char parity; */
127};
128
129#define SHARED_MEM_ADDRESS_SIZE 0x40000
130#define BUFFERLISTSIZE 4096
131#define DMABUFFERSIZE 4096
132#define MAXRXFRAMES 7
133
134typedef struct _DMABUFFERENTRY
135{
136 u32 phys_addr; /* 32-bit flat physical address of data buffer */
137 volatile u16 count; /* buffer size/data count */
138 volatile u16 status; /* Control/status field */
139 volatile u16 rcc; /* character count field */
140 u16 reserved; /* padding required by 16C32 */
141 u32 link; /* 32-bit flat link to next buffer entry */
142 char *virt_addr; /* virtual address of data buffer */
143 u32 phys_entry; /* physical address of this buffer entry */
144 dma_addr_t dma_addr;
145} DMABUFFERENTRY, *DMAPBUFFERENTRY;
146
147/* The queue of BH actions to be performed */
148
149#define BH_RECEIVE 1
150#define BH_TRANSMIT 2
151#define BH_STATUS 4
152
153#define IO_PIN_SHUTDOWN_LIMIT 100
154
155struct _input_signal_events {
156 int ri_up;
157 int ri_down;
158 int dsr_up;
159 int dsr_down;
160 int dcd_up;
161 int dcd_down;
162 int cts_up;
163 int cts_down;
164};
165
166/* transmit holding buffer definitions*/
167#define MAX_TX_HOLDING_BUFFERS 5
168struct tx_holding_buffer {
169 int buffer_size;
170 unsigned char * buffer;
171};
172
173
174/*
175 * Device instance data structure
176 */
177
178struct mgsl_struct {
179 int magic;
180 struct tty_port port;
181 int line;
182 int hw_version;
183
184 struct mgsl_icount icount;
185
186 int timeout;
187 int x_char; /* xon/xoff character */
188 u16 read_status_mask;
189 u16 ignore_status_mask;
190 unsigned char *xmit_buf;
191 int xmit_head;
192 int xmit_tail;
193 int xmit_cnt;
194
195 wait_queue_head_t status_event_wait_q;
196 wait_queue_head_t event_wait_q;
197 struct timer_list tx_timer; /* HDLC transmit timeout timer */
198 struct mgsl_struct *next_device; /* device list link */
199
200 spinlock_t irq_spinlock; /* spinlock for synchronizing with ISR */
201 struct work_struct task; /* task structure for scheduling bh */
202
203 u32 EventMask; /* event trigger mask */
204 u32 RecordedEvents; /* pending events */
205
206 u32 max_frame_size; /* as set by device config */
207
208 u32 pending_bh;
209
210 bool bh_running; /* Protection from multiple */
211 int isr_overflow;
212 bool bh_requested;
213
214 int dcd_chkcount; /* check counts to prevent */
215 int cts_chkcount; /* too many IRQs if a signal */
216 int dsr_chkcount; /* is floating */
217 int ri_chkcount;
218
219 char *buffer_list; /* virtual address of Rx & Tx buffer lists */
220 u32 buffer_list_phys;
221 dma_addr_t buffer_list_dma_addr;
222
223 unsigned int rx_buffer_count; /* count of total allocated Rx buffers */
224 DMABUFFERENTRY *rx_buffer_list; /* list of receive buffer entries */
225 unsigned int current_rx_buffer;
226
227 int num_tx_dma_buffers; /* number of tx dma frames required */
228 int tx_dma_buffers_used;
229 unsigned int tx_buffer_count; /* count of total allocated Tx buffers */
230 DMABUFFERENTRY *tx_buffer_list; /* list of transmit buffer entries */
231 int start_tx_dma_buffer; /* tx dma buffer to start tx dma operation */
232 int current_tx_buffer; /* next tx dma buffer to be loaded */
233
234 unsigned char *intermediate_rxbuffer;
235
236 int num_tx_holding_buffers; /* number of tx holding buffer allocated */
237 int get_tx_holding_index; /* next tx holding buffer for adapter to load */
238 int put_tx_holding_index; /* next tx holding buffer to store user request */
239 int tx_holding_count; /* number of tx holding buffers waiting */
240 struct tx_holding_buffer tx_holding_buffers[MAX_TX_HOLDING_BUFFERS];
241
242 bool rx_enabled;
243 bool rx_overflow;
244 bool rx_rcc_underrun;
245
246 bool tx_enabled;
247 bool tx_active;
248 u32 idle_mode;
249
250 u16 cmr_value;
251 u16 tcsr_value;
252
253 char device_name[25]; /* device instance name */
254
255 unsigned char bus; /* expansion bus number (zero based) */
256 unsigned char function; /* PCI device number */
257
258 unsigned int io_base; /* base I/O address of adapter */
259 unsigned int io_addr_size; /* size of the I/O address range */
260 bool io_addr_requested; /* true if I/O address requested */
261
262 unsigned int irq_level; /* interrupt level */
263 unsigned long irq_flags;
264 bool irq_requested; /* true if IRQ requested */
265
266 unsigned int dma_level; /* DMA channel */
267 bool dma_requested; /* true if dma channel requested */
268
269 u16 mbre_bit;
270 u16 loopback_bits;
271 u16 usc_idle_mode;
272
273 MGSL_PARAMS params; /* communications parameters */
274
275 unsigned char serial_signals; /* current serial signal states */
276
277 bool irq_occurred; /* for diagnostics use */
278 unsigned int init_error; /* Initialization startup error (DIAGS) */
279 int fDiagnosticsmode; /* Driver in Diagnostic mode? (DIAGS) */
280
281 u32 last_mem_alloc;
282 unsigned char* memory_base; /* shared memory address (PCI only) */
283 u32 phys_memory_base;
284 bool shared_mem_requested;
285
286 unsigned char* lcr_base; /* local config registers (PCI only) */
287 u32 phys_lcr_base;
288 u32 lcr_offset;
289 bool lcr_mem_requested;
290
291 u32 misc_ctrl_value;
292 char *flag_buf;
293 bool drop_rts_on_tx_done;
294
295 bool loopmode_insert_requested;
296 bool loopmode_send_done_requested;
297
298 struct _input_signal_events input_signal_events;
299
300 /* generic HDLC device parts */
301 int netcount;
302 spinlock_t netlock;
303
304#if SYNCLINK_GENERIC_HDLC
305 struct net_device *netdev;
306#endif
307};
308
309#define MGSL_MAGIC 0x5401
310
311/*
312 * The size of the serial xmit buffer is 1 page, or 4096 bytes
313 */
314#ifndef SERIAL_XMIT_SIZE
315#define SERIAL_XMIT_SIZE 4096
316#endif
317
318/*
319 * These macros define the offsets used in calculating the
320 * I/O address of the specified USC registers.
321 */
322
323
324#define DCPIN 2 /* Bit 1 of I/O address */
325#define SDPIN 4 /* Bit 2 of I/O address */
326
327#define DCAR 0 /* DMA command/address register */
328#define CCAR SDPIN /* channel command/address register */
329#define DATAREG DCPIN + SDPIN /* serial data register */
330#define MSBONLY 0x41
331#define LSBONLY 0x40
332
333/*
334 * These macros define the register address (ordinal number)
335 * used for writing address/value pairs to the USC.
336 */
337
338#define CMR 0x02 /* Channel mode Register */
339#define CCSR 0x04 /* Channel Command/status Register */
340#define CCR 0x06 /* Channel Control Register */
341#define PSR 0x08 /* Port status Register */
342#define PCR 0x0a /* Port Control Register */
343#define TMDR 0x0c /* Test mode Data Register */
344#define TMCR 0x0e /* Test mode Control Register */
345#define CMCR 0x10 /* Clock mode Control Register */
346#define HCR 0x12 /* Hardware Configuration Register */
347#define IVR 0x14 /* Interrupt Vector Register */
348#define IOCR 0x16 /* Input/Output Control Register */
349#define ICR 0x18 /* Interrupt Control Register */
350#define DCCR 0x1a /* Daisy Chain Control Register */
351#define MISR 0x1c /* Misc Interrupt status Register */
352#define SICR 0x1e /* status Interrupt Control Register */
353#define RDR 0x20 /* Receive Data Register */
354#define RMR 0x22 /* Receive mode Register */
355#define RCSR 0x24 /* Receive Command/status Register */
356#define RICR 0x26 /* Receive Interrupt Control Register */
357#define RSR 0x28 /* Receive Sync Register */
358#define RCLR 0x2a /* Receive count Limit Register */
359#define RCCR 0x2c /* Receive Character count Register */
360#define TC0R 0x2e /* Time Constant 0 Register */
361#define TDR 0x30 /* Transmit Data Register */
362#define TMR 0x32 /* Transmit mode Register */
363#define TCSR 0x34 /* Transmit Command/status Register */
364#define TICR 0x36 /* Transmit Interrupt Control Register */
365#define TSR 0x38 /* Transmit Sync Register */
366#define TCLR 0x3a /* Transmit count Limit Register */
367#define TCCR 0x3c /* Transmit Character count Register */
368#define TC1R 0x3e /* Time Constant 1 Register */
369
370
371/*
372 * MACRO DEFINITIONS FOR DMA REGISTERS
373 */
374
375#define DCR 0x06 /* DMA Control Register (shared) */
376#define DACR 0x08 /* DMA Array count Register (shared) */
377#define BDCR 0x12 /* Burst/Dwell Control Register (shared) */
378#define DIVR 0x14 /* DMA Interrupt Vector Register (shared) */
379#define DICR 0x18 /* DMA Interrupt Control Register (shared) */
380#define CDIR 0x1a /* Clear DMA Interrupt Register (shared) */
381#define SDIR 0x1c /* Set DMA Interrupt Register (shared) */
382
383#define TDMR 0x02 /* Transmit DMA mode Register */
384#define TDIAR 0x1e /* Transmit DMA Interrupt Arm Register */
385#define TBCR 0x2a /* Transmit Byte count Register */
386#define TARL 0x2c /* Transmit Address Register (low) */
387#define TARU 0x2e /* Transmit Address Register (high) */
388#define NTBCR 0x3a /* Next Transmit Byte count Register */
389#define NTARL 0x3c /* Next Transmit Address Register (low) */
390#define NTARU 0x3e /* Next Transmit Address Register (high) */
391
392#define RDMR 0x82 /* Receive DMA mode Register (non-shared) */
393#define RDIAR 0x9e /* Receive DMA Interrupt Arm Register */
394#define RBCR 0xaa /* Receive Byte count Register */
395#define RARL 0xac /* Receive Address Register (low) */
396#define RARU 0xae /* Receive Address Register (high) */
397#define NRBCR 0xba /* Next Receive Byte count Register */
398#define NRARL 0xbc /* Next Receive Address Register (low) */
399#define NRARU 0xbe /* Next Receive Address Register (high) */
400
401
402/*
403 * MACRO DEFINITIONS FOR MODEM STATUS BITS
404 */
405
406#define MODEMSTATUS_DTR 0x80
407#define MODEMSTATUS_DSR 0x40
408#define MODEMSTATUS_RTS 0x20
409#define MODEMSTATUS_CTS 0x10
410#define MODEMSTATUS_RI 0x04
411#define MODEMSTATUS_DCD 0x01
412
413
414/*
415 * Channel Command/Address Register (CCAR) Command Codes
416 */
417
418#define RTCmd_Null 0x0000
419#define RTCmd_ResetHighestIus 0x1000
420#define RTCmd_TriggerChannelLoadDma 0x2000
421#define RTCmd_TriggerRxDma 0x2800
422#define RTCmd_TriggerTxDma 0x3000
423#define RTCmd_TriggerRxAndTxDma 0x3800
424#define RTCmd_PurgeRxFifo 0x4800
425#define RTCmd_PurgeTxFifo 0x5000
426#define RTCmd_PurgeRxAndTxFifo 0x5800
427#define RTCmd_LoadRcc 0x6800
428#define RTCmd_LoadTcc 0x7000
429#define RTCmd_LoadRccAndTcc 0x7800
430#define RTCmd_LoadTC0 0x8800
431#define RTCmd_LoadTC1 0x9000
432#define RTCmd_LoadTC0AndTC1 0x9800
433#define RTCmd_SerialDataLSBFirst 0xa000
434#define RTCmd_SerialDataMSBFirst 0xa800
435#define RTCmd_SelectBigEndian 0xb000
436#define RTCmd_SelectLittleEndian 0xb800
437
438
439/*
440 * DMA Command/Address Register (DCAR) Command Codes
441 */
442
443#define DmaCmd_Null 0x0000
444#define DmaCmd_ResetTxChannel 0x1000
445#define DmaCmd_ResetRxChannel 0x1200
446#define DmaCmd_StartTxChannel 0x2000
447#define DmaCmd_StartRxChannel 0x2200
448#define DmaCmd_ContinueTxChannel 0x3000
449#define DmaCmd_ContinueRxChannel 0x3200
450#define DmaCmd_PauseTxChannel 0x4000
451#define DmaCmd_PauseRxChannel 0x4200
452#define DmaCmd_AbortTxChannel 0x5000
453#define DmaCmd_AbortRxChannel 0x5200
454#define DmaCmd_InitTxChannel 0x7000
455#define DmaCmd_InitRxChannel 0x7200
456#define DmaCmd_ResetHighestDmaIus 0x8000
457#define DmaCmd_ResetAllChannels 0x9000
458#define DmaCmd_StartAllChannels 0xa000
459#define DmaCmd_ContinueAllChannels 0xb000
460#define DmaCmd_PauseAllChannels 0xc000
461#define DmaCmd_AbortAllChannels 0xd000
462#define DmaCmd_InitAllChannels 0xf000
463
464#define TCmd_Null 0x0000
465#define TCmd_ClearTxCRC 0x2000
466#define TCmd_SelectTicrTtsaData 0x4000
467#define TCmd_SelectTicrTxFifostatus 0x5000
468#define TCmd_SelectTicrIntLevel 0x6000
469#define TCmd_SelectTicrdma_level 0x7000
470#define TCmd_SendFrame 0x8000
471#define TCmd_SendAbort 0x9000
472#define TCmd_EnableDleInsertion 0xc000
473#define TCmd_DisableDleInsertion 0xd000
474#define TCmd_ClearEofEom 0xe000
475#define TCmd_SetEofEom 0xf000
476
477#define RCmd_Null 0x0000
478#define RCmd_ClearRxCRC 0x2000
479#define RCmd_EnterHuntmode 0x3000
480#define RCmd_SelectRicrRtsaData 0x4000
481#define RCmd_SelectRicrRxFifostatus 0x5000
482#define RCmd_SelectRicrIntLevel 0x6000
483#define RCmd_SelectRicrdma_level 0x7000
484
485/*
486 * Bits for enabling and disabling IRQs in Interrupt Control Register (ICR)
487 */
488
489#define RECEIVE_STATUS BIT5
490#define RECEIVE_DATA BIT4
491#define TRANSMIT_STATUS BIT3
492#define TRANSMIT_DATA BIT2
493#define IO_PIN BIT1
494#define MISC BIT0
495
496
497/*
498 * Receive status Bits in Receive Command/status Register RCSR
499 */
500
501#define RXSTATUS_SHORT_FRAME BIT8
502#define RXSTATUS_CODE_VIOLATION BIT8
503#define RXSTATUS_EXITED_HUNT BIT7
504#define RXSTATUS_IDLE_RECEIVED BIT6
505#define RXSTATUS_BREAK_RECEIVED BIT5
506#define RXSTATUS_ABORT_RECEIVED BIT5
507#define RXSTATUS_RXBOUND BIT4
508#define RXSTATUS_CRC_ERROR BIT3
509#define RXSTATUS_FRAMING_ERROR BIT3
510#define RXSTATUS_ABORT BIT2
511#define RXSTATUS_PARITY_ERROR BIT2
512#define RXSTATUS_OVERRUN BIT1
513#define RXSTATUS_DATA_AVAILABLE BIT0
514#define RXSTATUS_ALL 0x01f6
515#define usc_UnlatchRxstatusBits(a,b) usc_OutReg( (a), RCSR, (u16)((b) & RXSTATUS_ALL) )
516
517/*
518 * Values for setting transmit idle mode in
519 * Transmit Control/status Register (TCSR)
520 */
521#define IDLEMODE_FLAGS 0x0000
522#define IDLEMODE_ALT_ONE_ZERO 0x0100
523#define IDLEMODE_ZERO 0x0200
524#define IDLEMODE_ONE 0x0300
525#define IDLEMODE_ALT_MARK_SPACE 0x0500
526#define IDLEMODE_SPACE 0x0600
527#define IDLEMODE_MARK 0x0700
528#define IDLEMODE_MASK 0x0700
529
530/*
531 * IUSC revision identifiers
532 */
533#define IUSC_SL1660 0x4d44
534#define IUSC_PRE_SL1660 0x4553
535
536/*
537 * Transmit status Bits in Transmit Command/status Register (TCSR)
538 */
539
540#define TCSR_PRESERVE 0x0F00
541
542#define TCSR_UNDERWAIT BIT11
543#define TXSTATUS_PREAMBLE_SENT BIT7
544#define TXSTATUS_IDLE_SENT BIT6
545#define TXSTATUS_ABORT_SENT BIT5
546#define TXSTATUS_EOF_SENT BIT4
547#define TXSTATUS_EOM_SENT BIT4
548#define TXSTATUS_CRC_SENT BIT3
549#define TXSTATUS_ALL_SENT BIT2
550#define TXSTATUS_UNDERRUN BIT1
551#define TXSTATUS_FIFO_EMPTY BIT0
552#define TXSTATUS_ALL 0x00fa
553#define usc_UnlatchTxstatusBits(a,b) usc_OutReg( (a), TCSR, (u16)((a)->tcsr_value + ((b) & 0x00FF)) )
554
555
556#define MISCSTATUS_RXC_LATCHED BIT15
557#define MISCSTATUS_RXC BIT14
558#define MISCSTATUS_TXC_LATCHED BIT13
559#define MISCSTATUS_TXC BIT12
560#define MISCSTATUS_RI_LATCHED BIT11
561#define MISCSTATUS_RI BIT10
562#define MISCSTATUS_DSR_LATCHED BIT9
563#define MISCSTATUS_DSR BIT8
564#define MISCSTATUS_DCD_LATCHED BIT7
565#define MISCSTATUS_DCD BIT6
566#define MISCSTATUS_CTS_LATCHED BIT5
567#define MISCSTATUS_CTS BIT4
568#define MISCSTATUS_RCC_UNDERRUN BIT3
569#define MISCSTATUS_DPLL_NO_SYNC BIT2
570#define MISCSTATUS_BRG1_ZERO BIT1
571#define MISCSTATUS_BRG0_ZERO BIT0
572
573#define usc_UnlatchIostatusBits(a,b) usc_OutReg((a),MISR,(u16)((b) & 0xaaa0))
574#define usc_UnlatchMiscstatusBits(a,b) usc_OutReg((a),MISR,(u16)((b) & 0x000f))
575
576#define SICR_RXC_ACTIVE BIT15
577#define SICR_RXC_INACTIVE BIT14
578#define SICR_RXC (BIT15|BIT14)
579#define SICR_TXC_ACTIVE BIT13
580#define SICR_TXC_INACTIVE BIT12
581#define SICR_TXC (BIT13|BIT12)
582#define SICR_RI_ACTIVE BIT11
583#define SICR_RI_INACTIVE BIT10
584#define SICR_RI (BIT11|BIT10)
585#define SICR_DSR_ACTIVE BIT9
586#define SICR_DSR_INACTIVE BIT8
587#define SICR_DSR (BIT9|BIT8)
588#define SICR_DCD_ACTIVE BIT7
589#define SICR_DCD_INACTIVE BIT6
590#define SICR_DCD (BIT7|BIT6)
591#define SICR_CTS_ACTIVE BIT5
592#define SICR_CTS_INACTIVE BIT4
593#define SICR_CTS (BIT5|BIT4)
594#define SICR_RCC_UNDERFLOW BIT3
595#define SICR_DPLL_NO_SYNC BIT2
596#define SICR_BRG1_ZERO BIT1
597#define SICR_BRG0_ZERO BIT0
598
599void usc_DisableMasterIrqBit( struct mgsl_struct *info );
600void usc_EnableMasterIrqBit( struct mgsl_struct *info );
601void usc_EnableInterrupts( struct mgsl_struct *info, u16 IrqMask );
602void usc_DisableInterrupts( struct mgsl_struct *info, u16 IrqMask );
603void usc_ClearIrqPendingBits( struct mgsl_struct *info, u16 IrqMask );
604
605#define usc_EnableInterrupts( a, b ) \
606 usc_OutReg( (a), ICR, (u16)((usc_InReg((a),ICR) & 0xff00) + 0xc0 + (b)) )
607
608#define usc_DisableInterrupts( a, b ) \
609 usc_OutReg( (a), ICR, (u16)((usc_InReg((a),ICR) & 0xff00) + 0x80 + (b)) )
610
611#define usc_EnableMasterIrqBit(a) \
612 usc_OutReg( (a), ICR, (u16)((usc_InReg((a),ICR) & 0x0f00) + 0xb000) )
613
614#define usc_DisableMasterIrqBit(a) \
615 usc_OutReg( (a), ICR, (u16)(usc_InReg((a),ICR) & 0x7f00) )
616
617#define usc_ClearIrqPendingBits( a, b ) usc_OutReg( (a), DCCR, 0x40 + (b) )
618
619/*
620 * Transmit status Bits in Transmit Control status Register (TCSR)
621 * and Transmit Interrupt Control Register (TICR) (except BIT2, BIT0)
622 */
623
624#define TXSTATUS_PREAMBLE_SENT BIT7
625#define TXSTATUS_IDLE_SENT BIT6
626#define TXSTATUS_ABORT_SENT BIT5
627#define TXSTATUS_EOF BIT4
628#define TXSTATUS_CRC_SENT BIT3
629#define TXSTATUS_ALL_SENT BIT2
630#define TXSTATUS_UNDERRUN BIT1
631#define TXSTATUS_FIFO_EMPTY BIT0
632
633#define DICR_MASTER BIT15
634#define DICR_TRANSMIT BIT0
635#define DICR_RECEIVE BIT1
636
637#define usc_EnableDmaInterrupts(a,b) \
638 usc_OutDmaReg( (a), DICR, (u16)(usc_InDmaReg((a),DICR) | (b)) )
639
640#define usc_DisableDmaInterrupts(a,b) \
641 usc_OutDmaReg( (a), DICR, (u16)(usc_InDmaReg((a),DICR) & ~(b)) )
642
643#define usc_EnableStatusIrqs(a,b) \
644 usc_OutReg( (a), SICR, (u16)(usc_InReg((a),SICR) | (b)) )
645
646#define usc_DisablestatusIrqs(a,b) \
647 usc_OutReg( (a), SICR, (u16)(usc_InReg((a),SICR) & ~(b)) )
648
649/* Transmit status Bits in Transmit Control status Register (TCSR) */
650/* and Transmit Interrupt Control Register (TICR) (except BIT2, BIT0) */
651
652
653#define DISABLE_UNCONDITIONAL 0
654#define DISABLE_END_OF_FRAME 1
655#define ENABLE_UNCONDITIONAL 2
656#define ENABLE_AUTO_CTS 3
657#define ENABLE_AUTO_DCD 3
658#define usc_EnableTransmitter(a,b) \
659 usc_OutReg( (a), TMR, (u16)((usc_InReg((a),TMR) & 0xfffc) | (b)) )
660#define usc_EnableReceiver(a,b) \
661 usc_OutReg( (a), RMR, (u16)((usc_InReg((a),RMR) & 0xfffc) | (b)) )
662
663static u16 usc_InDmaReg( struct mgsl_struct *info, u16 Port );
664static void usc_OutDmaReg( struct mgsl_struct *info, u16 Port, u16 Value );
665static void usc_DmaCmd( struct mgsl_struct *info, u16 Cmd );
666
667static u16 usc_InReg( struct mgsl_struct *info, u16 Port );
668static void usc_OutReg( struct mgsl_struct *info, u16 Port, u16 Value );
669static void usc_RTCmd( struct mgsl_struct *info, u16 Cmd );
670void usc_RCmd( struct mgsl_struct *info, u16 Cmd );
671void usc_TCmd( struct mgsl_struct *info, u16 Cmd );
672
673#define usc_TCmd(a,b) usc_OutReg((a), TCSR, (u16)((a)->tcsr_value + (b)))
674#define usc_RCmd(a,b) usc_OutReg((a), RCSR, (b))
675
676#define usc_SetTransmitSyncChars(a,s0,s1) usc_OutReg((a), TSR, (u16)(((u16)s0<<8)|(u16)s1))
677
678static void usc_process_rxoverrun_sync( struct mgsl_struct *info );
679static void usc_start_receiver( struct mgsl_struct *info );
680static void usc_stop_receiver( struct mgsl_struct *info );
681
682static void usc_start_transmitter( struct mgsl_struct *info );
683static void usc_stop_transmitter( struct mgsl_struct *info );
684static void usc_set_txidle( struct mgsl_struct *info );
685static void usc_load_txfifo( struct mgsl_struct *info );
686
687static void usc_enable_aux_clock( struct mgsl_struct *info, u32 DataRate );
688static void usc_enable_loopback( struct mgsl_struct *info, int enable );
689
690static void usc_get_serial_signals( struct mgsl_struct *info );
691static void usc_set_serial_signals( struct mgsl_struct *info );
692
693static void usc_reset( struct mgsl_struct *info );
694
695static void usc_set_sync_mode( struct mgsl_struct *info );
696static void usc_set_sdlc_mode( struct mgsl_struct *info );
697static void usc_set_async_mode( struct mgsl_struct *info );
698static void usc_enable_async_clock( struct mgsl_struct *info, u32 DataRate );
699
700static void usc_loopback_frame( struct mgsl_struct *info );
701
702static void mgsl_tx_timeout(struct timer_list *t);
703
704
705static void usc_loopmode_cancel_transmit( struct mgsl_struct * info );
706static void usc_loopmode_insert_request( struct mgsl_struct * info );
707static int usc_loopmode_active( struct mgsl_struct * info);
708static void usc_loopmode_send_done( struct mgsl_struct * info );
709
710static int mgsl_ioctl_common(struct mgsl_struct *info, unsigned int cmd, unsigned long arg);
711
712#if SYNCLINK_GENERIC_HDLC
713#define dev_to_port(D) (dev_to_hdlc(D)->priv)
714static void hdlcdev_tx_done(struct mgsl_struct *info);
715static void hdlcdev_rx(struct mgsl_struct *info, char *buf, int size);
716static int hdlcdev_init(struct mgsl_struct *info);
717static void hdlcdev_exit(struct mgsl_struct *info);
718#endif
719
720/*
721 * Defines a BUS descriptor value for the PCI adapter
722 * local bus address ranges.
723 */
724
725#define BUS_DESCRIPTOR( WrHold, WrDly, RdDly, Nwdd, Nwad, Nxda, Nrdd, Nrad ) \
726(0x00400020 + \
727((WrHold) << 30) + \
728((WrDly) << 28) + \
729((RdDly) << 26) + \
730((Nwdd) << 20) + \
731((Nwad) << 15) + \
732((Nxda) << 13) + \
733((Nrdd) << 11) + \
734((Nrad) << 6) )
735
736static void mgsl_trace_block(struct mgsl_struct *info,const char* data, int count, int xmit);
737
738/*
739 * Adapter diagnostic routines
740 */
741static bool mgsl_register_test( struct mgsl_struct *info );
742static bool mgsl_irq_test( struct mgsl_struct *info );
743static bool mgsl_dma_test( struct mgsl_struct *info );
744static bool mgsl_memory_test( struct mgsl_struct *info );
745static int mgsl_adapter_test( struct mgsl_struct *info );
746
747/*
748 * device and resource management routines
749 */
750static int mgsl_claim_resources(struct mgsl_struct *info);
751static void mgsl_release_resources(struct mgsl_struct *info);
752static void mgsl_add_device(struct mgsl_struct *info);
753static struct mgsl_struct* mgsl_allocate_device(void);
754
755/*
756 * DMA buffer manupulation functions.
757 */
758static void mgsl_free_rx_frame_buffers( struct mgsl_struct *info, unsigned int StartIndex, unsigned int EndIndex );
759static bool mgsl_get_rx_frame( struct mgsl_struct *info );
760static bool mgsl_get_raw_rx_frame( struct mgsl_struct *info );
761static void mgsl_reset_rx_dma_buffers( struct mgsl_struct *info );
762static void mgsl_reset_tx_dma_buffers( struct mgsl_struct *info );
763static int num_free_tx_dma_buffers(struct mgsl_struct *info);
764static void mgsl_load_tx_dma_buffer( struct mgsl_struct *info, const char *Buffer, unsigned int BufferSize);
765static void mgsl_load_pci_memory(char* TargetPtr, const char* SourcePtr, unsigned short count);
766
767/*
768 * DMA and Shared Memory buffer allocation and formatting
769 */
770static int mgsl_allocate_dma_buffers(struct mgsl_struct *info);
771static void mgsl_free_dma_buffers(struct mgsl_struct *info);
772static int mgsl_alloc_frame_memory(struct mgsl_struct *info, DMABUFFERENTRY *BufferList,int Buffercount);
773static void mgsl_free_frame_memory(struct mgsl_struct *info, DMABUFFERENTRY *BufferList,int Buffercount);
774static int mgsl_alloc_buffer_list_memory(struct mgsl_struct *info);
775static void mgsl_free_buffer_list_memory(struct mgsl_struct *info);
776static int mgsl_alloc_intermediate_rxbuffer_memory(struct mgsl_struct *info);
777static void mgsl_free_intermediate_rxbuffer_memory(struct mgsl_struct *info);
778static int mgsl_alloc_intermediate_txbuffer_memory(struct mgsl_struct *info);
779static void mgsl_free_intermediate_txbuffer_memory(struct mgsl_struct *info);
780static bool load_next_tx_holding_buffer(struct mgsl_struct *info);
781static int save_tx_buffer_request(struct mgsl_struct *info,const char *Buffer, unsigned int BufferSize);
782
783/*
784 * Bottom half interrupt handlers
785 */
786static void mgsl_bh_handler(struct work_struct *work);
787static void mgsl_bh_receive(struct mgsl_struct *info);
788static void mgsl_bh_transmit(struct mgsl_struct *info);
789static void mgsl_bh_status(struct mgsl_struct *info);
790
791/*
792 * Interrupt handler routines and dispatch table.
793 */
794static void mgsl_isr_null( struct mgsl_struct *info );
795static void mgsl_isr_transmit_data( struct mgsl_struct *info );
796static void mgsl_isr_receive_data( struct mgsl_struct *info );
797static void mgsl_isr_receive_status( struct mgsl_struct *info );
798static void mgsl_isr_transmit_status( struct mgsl_struct *info );
799static void mgsl_isr_io_pin( struct mgsl_struct *info );
800static void mgsl_isr_misc( struct mgsl_struct *info );
801static void mgsl_isr_receive_dma( struct mgsl_struct *info );
802static void mgsl_isr_transmit_dma( struct mgsl_struct *info );
803
804typedef void (*isr_dispatch_func)(struct mgsl_struct *);
805
806static isr_dispatch_func UscIsrTable[7] =
807{
808 mgsl_isr_null,
809 mgsl_isr_misc,
810 mgsl_isr_io_pin,
811 mgsl_isr_transmit_data,
812 mgsl_isr_transmit_status,
813 mgsl_isr_receive_data,
814 mgsl_isr_receive_status
815};
816
817/*
818 * ioctl call handlers
819 */
820static int tiocmget(struct tty_struct *tty);
821static int tiocmset(struct tty_struct *tty,
822 unsigned int set, unsigned int clear);
823static int mgsl_get_stats(struct mgsl_struct * info, struct mgsl_icount
824 __user *user_icount);
825static int mgsl_get_params(struct mgsl_struct * info, MGSL_PARAMS __user *user_params);
826static int mgsl_set_params(struct mgsl_struct * info, MGSL_PARAMS __user *new_params);
827static int mgsl_get_txidle(struct mgsl_struct * info, int __user *idle_mode);
828static int mgsl_set_txidle(struct mgsl_struct * info, int idle_mode);
829static int mgsl_txenable(struct mgsl_struct * info, int enable);
830static int mgsl_txabort(struct mgsl_struct * info);
831static int mgsl_rxenable(struct mgsl_struct * info, int enable);
832static int mgsl_wait_event(struct mgsl_struct * info, int __user *mask);
833static int mgsl_loopmode_send_done( struct mgsl_struct * info );
834
835/* set non-zero on successful registration with PCI subsystem */
836static bool pci_registered;
837
838/*
839 * Global linked list of SyncLink devices
840 */
841static struct mgsl_struct *mgsl_device_list;
842static int mgsl_device_count;
843
844/*
845 * Set this param to non-zero to load eax with the
846 * .text section address and breakpoint on module load.
847 * This is useful for use with gdb and add-symbol-file command.
848 */
849static bool break_on_load;
850
851/*
852 * Driver major number, defaults to zero to get auto
853 * assigned major number. May be forced as module parameter.
854 */
855static int ttymajor;
856
857/*
858 * Array of user specified options for ISA adapters.
859 */
860static int io[MAX_ISA_DEVICES];
861static int irq[MAX_ISA_DEVICES];
862static int dma[MAX_ISA_DEVICES];
863static int debug_level;
864static int maxframe[MAX_TOTAL_DEVICES];
865static int txdmabufs[MAX_TOTAL_DEVICES];
866static int txholdbufs[MAX_TOTAL_DEVICES];
867
868module_param(break_on_load, bool, 0);
869module_param(ttymajor, int, 0);
870module_param_hw_array(io, int, ioport, NULL, 0);
871module_param_hw_array(irq, int, irq, NULL, 0);
872module_param_hw_array(dma, int, dma, NULL, 0);
873module_param(debug_level, int, 0);
874module_param_array(maxframe, int, NULL, 0);
875module_param_array(txdmabufs, int, NULL, 0);
876module_param_array(txholdbufs, int, NULL, 0);
877
878static char *driver_name = "SyncLink serial driver";
879static char *driver_version = "$Revision: 4.38 $";
880
881static int synclink_init_one (struct pci_dev *dev,
882 const struct pci_device_id *ent);
883static void synclink_remove_one (struct pci_dev *dev);
884
885static const struct pci_device_id synclink_pci_tbl[] = {
886 { PCI_VENDOR_ID_MICROGATE, PCI_DEVICE_ID_MICROGATE_USC, PCI_ANY_ID, PCI_ANY_ID, },
887 { PCI_VENDOR_ID_MICROGATE, 0x0210, PCI_ANY_ID, PCI_ANY_ID, },
888 { 0, }, /* terminate list */
889};
890MODULE_DEVICE_TABLE(pci, synclink_pci_tbl);
891
892MODULE_LICENSE("GPL");
893
894static struct pci_driver synclink_pci_driver = {
895 .name = "synclink",
896 .id_table = synclink_pci_tbl,
897 .probe = synclink_init_one,
898 .remove = synclink_remove_one,
899};
900
901static struct tty_driver *serial_driver;
902
903/* number of characters left in xmit buffer before we ask for more */
904#define WAKEUP_CHARS 256
905
906
907static void mgsl_change_params(struct mgsl_struct *info);
908static void mgsl_wait_until_sent(struct tty_struct *tty, int timeout);
909
910/*
911 * 1st function defined in .text section. Calling this function in
912 * init_module() followed by a breakpoint allows a remote debugger
913 * (gdb) to get the .text address for the add-symbol-file command.
914 * This allows remote debugging of dynamically loadable modules.
915 */
916static void* mgsl_get_text_ptr(void)
917{
918 return mgsl_get_text_ptr;
919}
920
921static inline int mgsl_paranoia_check(struct mgsl_struct *info,
922 char *name, const char *routine)
923{
924#ifdef MGSL_PARANOIA_CHECK
925 static const char *badmagic =
926 "Warning: bad magic number for mgsl struct (%s) in %s\n";
927 static const char *badinfo =
928 "Warning: null mgsl_struct for (%s) in %s\n";
929
930 if (!info) {
931 printk(badinfo, name, routine);
932 return 1;
933 }
934 if (info->magic != MGSL_MAGIC) {
935 printk(badmagic, name, routine);
936 return 1;
937 }
938#else
939 if (!info)
940 return 1;
941#endif
942 return 0;
943}
944
945/**
946 * line discipline callback wrappers
947 *
948 * The wrappers maintain line discipline references
949 * while calling into the line discipline.
950 *
951 * ldisc_receive_buf - pass receive data to line discipline
952 */
953
954static void ldisc_receive_buf(struct tty_struct *tty,
955 const __u8 *data, char *flags, int count)
956{
957 struct tty_ldisc *ld;
958 if (!tty)
959 return;
960 ld = tty_ldisc_ref(tty);
961 if (ld) {
962 if (ld->ops->receive_buf)
963 ld->ops->receive_buf(tty, data, flags, count);
964 tty_ldisc_deref(ld);
965 }
966}
967
968/* mgsl_stop() throttle (stop) transmitter
969 *
970 * Arguments: tty pointer to tty info structure
971 * Return Value: None
972 */
973static void mgsl_stop(struct tty_struct *tty)
974{
975 struct mgsl_struct *info = tty->driver_data;
976 unsigned long flags;
977
978 if (mgsl_paranoia_check(info, tty->name, "mgsl_stop"))
979 return;
980
981 if ( debug_level >= DEBUG_LEVEL_INFO )
982 printk("mgsl_stop(%s)\n",info->device_name);
983
984 spin_lock_irqsave(&info->irq_spinlock,flags);
985 if (info->tx_enabled)
986 usc_stop_transmitter(info);
987 spin_unlock_irqrestore(&info->irq_spinlock,flags);
988
989} /* end of mgsl_stop() */
990
991/* mgsl_start() release (start) transmitter
992 *
993 * Arguments: tty pointer to tty info structure
994 * Return Value: None
995 */
996static void mgsl_start(struct tty_struct *tty)
997{
998 struct mgsl_struct *info = tty->driver_data;
999 unsigned long flags;
1000
1001 if (mgsl_paranoia_check(info, tty->name, "mgsl_start"))
1002 return;
1003
1004 if ( debug_level >= DEBUG_LEVEL_INFO )
1005 printk("mgsl_start(%s)\n",info->device_name);
1006
1007 spin_lock_irqsave(&info->irq_spinlock,flags);
1008 if (!info->tx_enabled)
1009 usc_start_transmitter(info);
1010 spin_unlock_irqrestore(&info->irq_spinlock,flags);
1011
1012} /* end of mgsl_start() */
1013
1014/*
1015 * Bottom half work queue access functions
1016 */
1017
1018/* mgsl_bh_action() Return next bottom half action to perform.
1019 * Return Value: BH action code or 0 if nothing to do.
1020 */
1021static int mgsl_bh_action(struct mgsl_struct *info)
1022{
1023 unsigned long flags;
1024 int rc = 0;
1025
1026 spin_lock_irqsave(&info->irq_spinlock,flags);
1027
1028 if (info->pending_bh & BH_RECEIVE) {
1029 info->pending_bh &= ~BH_RECEIVE;
1030 rc = BH_RECEIVE;
1031 } else if (info->pending_bh & BH_TRANSMIT) {
1032 info->pending_bh &= ~BH_TRANSMIT;
1033 rc = BH_TRANSMIT;
1034 } else if (info->pending_bh & BH_STATUS) {
1035 info->pending_bh &= ~BH_STATUS;
1036 rc = BH_STATUS;
1037 }
1038
1039 if (!rc) {
1040 /* Mark BH routine as complete */
1041 info->bh_running = false;
1042 info->bh_requested = false;
1043 }
1044
1045 spin_unlock_irqrestore(&info->irq_spinlock,flags);
1046
1047 return rc;
1048}
1049
1050/*
1051 * Perform bottom half processing of work items queued by ISR.
1052 */
1053static void mgsl_bh_handler(struct work_struct *work)
1054{
1055 struct mgsl_struct *info =
1056 container_of(work, struct mgsl_struct, task);
1057 int action;
1058
1059 if ( debug_level >= DEBUG_LEVEL_BH )
1060 printk( "%s(%d):mgsl_bh_handler(%s) entry\n",
1061 __FILE__,__LINE__,info->device_name);
1062
1063 info->bh_running = true;
1064
1065 while((action = mgsl_bh_action(info)) != 0) {
1066
1067 /* Process work item */
1068 if ( debug_level >= DEBUG_LEVEL_BH )
1069 printk( "%s(%d):mgsl_bh_handler() work item action=%d\n",
1070 __FILE__,__LINE__,action);
1071
1072 switch (action) {
1073
1074 case BH_RECEIVE:
1075 mgsl_bh_receive(info);
1076 break;
1077 case BH_TRANSMIT:
1078 mgsl_bh_transmit(info);
1079 break;
1080 case BH_STATUS:
1081 mgsl_bh_status(info);
1082 break;
1083 default:
1084 /* unknown work item ID */
1085 printk("Unknown work item ID=%08X!\n", action);
1086 break;
1087 }
1088 }
1089
1090 if ( debug_level >= DEBUG_LEVEL_BH )
1091 printk( "%s(%d):mgsl_bh_handler(%s) exit\n",
1092 __FILE__,__LINE__,info->device_name);
1093}
1094
1095static void mgsl_bh_receive(struct mgsl_struct *info)
1096{
1097 bool (*get_rx_frame)(struct mgsl_struct *info) =
1098 (info->params.mode == MGSL_MODE_HDLC ? mgsl_get_rx_frame : mgsl_get_raw_rx_frame);
1099
1100 if ( debug_level >= DEBUG_LEVEL_BH )
1101 printk( "%s(%d):mgsl_bh_receive(%s)\n",
1102 __FILE__,__LINE__,info->device_name);
1103
1104 do
1105 {
1106 if (info->rx_rcc_underrun) {
1107 unsigned long flags;
1108 spin_lock_irqsave(&info->irq_spinlock,flags);
1109 usc_start_receiver(info);
1110 spin_unlock_irqrestore(&info->irq_spinlock,flags);
1111 return;
1112 }
1113 } while(get_rx_frame(info));
1114}
1115
1116static void mgsl_bh_transmit(struct mgsl_struct *info)
1117{
1118 struct tty_struct *tty = info->port.tty;
1119 unsigned long flags;
1120
1121 if ( debug_level >= DEBUG_LEVEL_BH )
1122 printk( "%s(%d):mgsl_bh_transmit() entry on %s\n",
1123 __FILE__,__LINE__,info->device_name);
1124
1125 if (tty)
1126 tty_wakeup(tty);
1127
1128 /* if transmitter idle and loopmode_send_done_requested
1129 * then start echoing RxD to TxD
1130 */
1131 spin_lock_irqsave(&info->irq_spinlock,flags);
1132 if ( !info->tx_active && info->loopmode_send_done_requested )
1133 usc_loopmode_send_done( info );
1134 spin_unlock_irqrestore(&info->irq_spinlock,flags);
1135}
1136
1137static void mgsl_bh_status(struct mgsl_struct *info)
1138{
1139 if ( debug_level >= DEBUG_LEVEL_BH )
1140 printk( "%s(%d):mgsl_bh_status() entry on %s\n",
1141 __FILE__,__LINE__,info->device_name);
1142
1143 info->ri_chkcount = 0;
1144 info->dsr_chkcount = 0;
1145 info->dcd_chkcount = 0;
1146 info->cts_chkcount = 0;
1147}
1148
1149/* mgsl_isr_receive_status()
1150 *
1151 * Service a receive status interrupt. The type of status
1152 * interrupt is indicated by the state of the RCSR.
1153 * This is only used for HDLC mode.
1154 *
1155 * Arguments: info pointer to device instance data
1156 * Return Value: None
1157 */
1158static void mgsl_isr_receive_status( struct mgsl_struct *info )
1159{
1160 u16 status = usc_InReg( info, RCSR );
1161
1162 if ( debug_level >= DEBUG_LEVEL_ISR )
1163 printk("%s(%d):mgsl_isr_receive_status status=%04X\n",
1164 __FILE__,__LINE__,status);
1165
1166 if ( (status & RXSTATUS_ABORT_RECEIVED) &&
1167 info->loopmode_insert_requested &&
1168 usc_loopmode_active(info) )
1169 {
1170 ++info->icount.rxabort;
1171 info->loopmode_insert_requested = false;
1172
1173 /* clear CMR:13 to start echoing RxD to TxD */
1174 info->cmr_value &= ~BIT13;
1175 usc_OutReg(info, CMR, info->cmr_value);
1176
1177 /* disable received abort irq (no longer required) */
1178 usc_OutReg(info, RICR,
1179 (usc_InReg(info, RICR) & ~RXSTATUS_ABORT_RECEIVED));
1180 }
1181
1182 if (status & (RXSTATUS_EXITED_HUNT | RXSTATUS_IDLE_RECEIVED)) {
1183 if (status & RXSTATUS_EXITED_HUNT)
1184 info->icount.exithunt++;
1185 if (status & RXSTATUS_IDLE_RECEIVED)
1186 info->icount.rxidle++;
1187 wake_up_interruptible(&info->event_wait_q);
1188 }
1189
1190 if (status & RXSTATUS_OVERRUN){
1191 info->icount.rxover++;
1192 usc_process_rxoverrun_sync( info );
1193 }
1194
1195 usc_ClearIrqPendingBits( info, RECEIVE_STATUS );
1196 usc_UnlatchRxstatusBits( info, status );
1197
1198} /* end of mgsl_isr_receive_status() */
1199
1200/* mgsl_isr_transmit_status()
1201 *
1202 * Service a transmit status interrupt
1203 * HDLC mode :end of transmit frame
1204 * Async mode:all data is sent
1205 * transmit status is indicated by bits in the TCSR.
1206 *
1207 * Arguments: info pointer to device instance data
1208 * Return Value: None
1209 */
1210static void mgsl_isr_transmit_status( struct mgsl_struct *info )
1211{
1212 u16 status = usc_InReg( info, TCSR );
1213
1214 if ( debug_level >= DEBUG_LEVEL_ISR )
1215 printk("%s(%d):mgsl_isr_transmit_status status=%04X\n",
1216 __FILE__,__LINE__,status);
1217
1218 usc_ClearIrqPendingBits( info, TRANSMIT_STATUS );
1219 usc_UnlatchTxstatusBits( info, status );
1220
1221 if ( status & (TXSTATUS_UNDERRUN | TXSTATUS_ABORT_SENT) )
1222 {
1223 /* finished sending HDLC abort. This may leave */
1224 /* the TxFifo with data from the aborted frame */
1225 /* so purge the TxFifo. Also shutdown the DMA */
1226 /* channel in case there is data remaining in */
1227 /* the DMA buffer */
1228 usc_DmaCmd( info, DmaCmd_ResetTxChannel );
1229 usc_RTCmd( info, RTCmd_PurgeTxFifo );
1230 }
1231
1232 if ( status & TXSTATUS_EOF_SENT )
1233 info->icount.txok++;
1234 else if ( status & TXSTATUS_UNDERRUN )
1235 info->icount.txunder++;
1236 else if ( status & TXSTATUS_ABORT_SENT )
1237 info->icount.txabort++;
1238 else
1239 info->icount.txunder++;
1240
1241 info->tx_active = false;
1242 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
1243 del_timer(&info->tx_timer);
1244
1245 if ( info->drop_rts_on_tx_done ) {
1246 usc_get_serial_signals( info );
1247 if ( info->serial_signals & SerialSignal_RTS ) {
1248 info->serial_signals &= ~SerialSignal_RTS;
1249 usc_set_serial_signals( info );
1250 }
1251 info->drop_rts_on_tx_done = false;
1252 }
1253
1254#if SYNCLINK_GENERIC_HDLC
1255 if (info->netcount)
1256 hdlcdev_tx_done(info);
1257 else
1258#endif
1259 {
1260 if (info->port.tty->stopped || info->port.tty->hw_stopped) {
1261 usc_stop_transmitter(info);
1262 return;
1263 }
1264 info->pending_bh |= BH_TRANSMIT;
1265 }
1266
1267} /* end of mgsl_isr_transmit_status() */
1268
1269/* mgsl_isr_io_pin()
1270 *
1271 * Service an Input/Output pin interrupt. The type of
1272 * interrupt is indicated by bits in the MISR
1273 *
1274 * Arguments: info pointer to device instance data
1275 * Return Value: None
1276 */
1277static void mgsl_isr_io_pin( struct mgsl_struct *info )
1278{
1279 struct mgsl_icount *icount;
1280 u16 status = usc_InReg( info, MISR );
1281
1282 if ( debug_level >= DEBUG_LEVEL_ISR )
1283 printk("%s(%d):mgsl_isr_io_pin status=%04X\n",
1284 __FILE__,__LINE__,status);
1285
1286 usc_ClearIrqPendingBits( info, IO_PIN );
1287 usc_UnlatchIostatusBits( info, status );
1288
1289 if (status & (MISCSTATUS_CTS_LATCHED | MISCSTATUS_DCD_LATCHED |
1290 MISCSTATUS_DSR_LATCHED | MISCSTATUS_RI_LATCHED) ) {
1291 icount = &info->icount;
1292 /* update input line counters */
1293 if (status & MISCSTATUS_RI_LATCHED) {
1294 if ((info->ri_chkcount)++ >= IO_PIN_SHUTDOWN_LIMIT)
1295 usc_DisablestatusIrqs(info,SICR_RI);
1296 icount->rng++;
1297 if ( status & MISCSTATUS_RI )
1298 info->input_signal_events.ri_up++;
1299 else
1300 info->input_signal_events.ri_down++;
1301 }
1302 if (status & MISCSTATUS_DSR_LATCHED) {
1303 if ((info->dsr_chkcount)++ >= IO_PIN_SHUTDOWN_LIMIT)
1304 usc_DisablestatusIrqs(info,SICR_DSR);
1305 icount->dsr++;
1306 if ( status & MISCSTATUS_DSR )
1307 info->input_signal_events.dsr_up++;
1308 else
1309 info->input_signal_events.dsr_down++;
1310 }
1311 if (status & MISCSTATUS_DCD_LATCHED) {
1312 if ((info->dcd_chkcount)++ >= IO_PIN_SHUTDOWN_LIMIT)
1313 usc_DisablestatusIrqs(info,SICR_DCD);
1314 icount->dcd++;
1315 if (status & MISCSTATUS_DCD) {
1316 info->input_signal_events.dcd_up++;
1317 } else
1318 info->input_signal_events.dcd_down++;
1319#if SYNCLINK_GENERIC_HDLC
1320 if (info->netcount) {
1321 if (status & MISCSTATUS_DCD)
1322 netif_carrier_on(info->netdev);
1323 else
1324 netif_carrier_off(info->netdev);
1325 }
1326#endif
1327 }
1328 if (status & MISCSTATUS_CTS_LATCHED)
1329 {
1330 if ((info->cts_chkcount)++ >= IO_PIN_SHUTDOWN_LIMIT)
1331 usc_DisablestatusIrqs(info,SICR_CTS);
1332 icount->cts++;
1333 if ( status & MISCSTATUS_CTS )
1334 info->input_signal_events.cts_up++;
1335 else
1336 info->input_signal_events.cts_down++;
1337 }
1338 wake_up_interruptible(&info->status_event_wait_q);
1339 wake_up_interruptible(&info->event_wait_q);
1340
1341 if (tty_port_check_carrier(&info->port) &&
1342 (status & MISCSTATUS_DCD_LATCHED) ) {
1343 if ( debug_level >= DEBUG_LEVEL_ISR )
1344 printk("%s CD now %s...", info->device_name,
1345 (status & MISCSTATUS_DCD) ? "on" : "off");
1346 if (status & MISCSTATUS_DCD)
1347 wake_up_interruptible(&info->port.open_wait);
1348 else {
1349 if ( debug_level >= DEBUG_LEVEL_ISR )
1350 printk("doing serial hangup...");
1351 if (info->port.tty)
1352 tty_hangup(info->port.tty);
1353 }
1354 }
1355
1356 if (tty_port_cts_enabled(&info->port) &&
1357 (status & MISCSTATUS_CTS_LATCHED) ) {
1358 if (info->port.tty->hw_stopped) {
1359 if (status & MISCSTATUS_CTS) {
1360 if ( debug_level >= DEBUG_LEVEL_ISR )
1361 printk("CTS tx start...");
1362 info->port.tty->hw_stopped = 0;
1363 usc_start_transmitter(info);
1364 info->pending_bh |= BH_TRANSMIT;
1365 return;
1366 }
1367 } else {
1368 if (!(status & MISCSTATUS_CTS)) {
1369 if ( debug_level >= DEBUG_LEVEL_ISR )
1370 printk("CTS tx stop...");
1371 if (info->port.tty)
1372 info->port.tty->hw_stopped = 1;
1373 usc_stop_transmitter(info);
1374 }
1375 }
1376 }
1377 }
1378
1379 info->pending_bh |= BH_STATUS;
1380
1381 /* for diagnostics set IRQ flag */
1382 if ( status & MISCSTATUS_TXC_LATCHED ){
1383 usc_OutReg( info, SICR,
1384 (unsigned short)(usc_InReg(info,SICR) & ~(SICR_TXC_ACTIVE+SICR_TXC_INACTIVE)) );
1385 usc_UnlatchIostatusBits( info, MISCSTATUS_TXC_LATCHED );
1386 info->irq_occurred = true;
1387 }
1388
1389} /* end of mgsl_isr_io_pin() */
1390
1391/* mgsl_isr_transmit_data()
1392 *
1393 * Service a transmit data interrupt (async mode only).
1394 *
1395 * Arguments: info pointer to device instance data
1396 * Return Value: None
1397 */
1398static void mgsl_isr_transmit_data( struct mgsl_struct *info )
1399{
1400 if ( debug_level >= DEBUG_LEVEL_ISR )
1401 printk("%s(%d):mgsl_isr_transmit_data xmit_cnt=%d\n",
1402 __FILE__,__LINE__,info->xmit_cnt);
1403
1404 usc_ClearIrqPendingBits( info, TRANSMIT_DATA );
1405
1406 if (info->port.tty->stopped || info->port.tty->hw_stopped) {
1407 usc_stop_transmitter(info);
1408 return;
1409 }
1410
1411 if ( info->xmit_cnt )
1412 usc_load_txfifo( info );
1413 else
1414 info->tx_active = false;
1415
1416 if (info->xmit_cnt < WAKEUP_CHARS)
1417 info->pending_bh |= BH_TRANSMIT;
1418
1419} /* end of mgsl_isr_transmit_data() */
1420
1421/* mgsl_isr_receive_data()
1422 *
1423 * Service a receive data interrupt. This occurs
1424 * when operating in asynchronous interrupt transfer mode.
1425 * The receive data FIFO is flushed to the receive data buffers.
1426 *
1427 * Arguments: info pointer to device instance data
1428 * Return Value: None
1429 */
1430static void mgsl_isr_receive_data( struct mgsl_struct *info )
1431{
1432 int Fifocount;
1433 u16 status;
1434 int work = 0;
1435 unsigned char DataByte;
1436 struct mgsl_icount *icount = &info->icount;
1437
1438 if ( debug_level >= DEBUG_LEVEL_ISR )
1439 printk("%s(%d):mgsl_isr_receive_data\n",
1440 __FILE__,__LINE__);
1441
1442 usc_ClearIrqPendingBits( info, RECEIVE_DATA );
1443
1444 /* select FIFO status for RICR readback */
1445 usc_RCmd( info, RCmd_SelectRicrRxFifostatus );
1446
1447 /* clear the Wordstatus bit so that status readback */
1448 /* only reflects the status of this byte */
1449 usc_OutReg( info, RICR+LSBONLY, (u16)(usc_InReg(info, RICR+LSBONLY) & ~BIT3 ));
1450
1451 /* flush the receive FIFO */
1452
1453 while( (Fifocount = (usc_InReg(info,RICR) >> 8)) ) {
1454 int flag;
1455
1456 /* read one byte from RxFIFO */
1457 outw( (inw(info->io_base + CCAR) & 0x0780) | (RDR+LSBONLY),
1458 info->io_base + CCAR );
1459 DataByte = inb( info->io_base + CCAR );
1460
1461 /* get the status of the received byte */
1462 status = usc_InReg(info, RCSR);
1463 if ( status & (RXSTATUS_FRAMING_ERROR | RXSTATUS_PARITY_ERROR |
1464 RXSTATUS_OVERRUN | RXSTATUS_BREAK_RECEIVED) )
1465 usc_UnlatchRxstatusBits(info,RXSTATUS_ALL);
1466
1467 icount->rx++;
1468
1469 flag = 0;
1470 if ( status & (RXSTATUS_FRAMING_ERROR | RXSTATUS_PARITY_ERROR |
1471 RXSTATUS_OVERRUN | RXSTATUS_BREAK_RECEIVED) ) {
1472 printk("rxerr=%04X\n",status);
1473 /* update error statistics */
1474 if ( status & RXSTATUS_BREAK_RECEIVED ) {
1475 status &= ~(RXSTATUS_FRAMING_ERROR | RXSTATUS_PARITY_ERROR);
1476 icount->brk++;
1477 } else if (status & RXSTATUS_PARITY_ERROR)
1478 icount->parity++;
1479 else if (status & RXSTATUS_FRAMING_ERROR)
1480 icount->frame++;
1481 else if (status & RXSTATUS_OVERRUN) {
1482 /* must issue purge fifo cmd before */
1483 /* 16C32 accepts more receive chars */
1484 usc_RTCmd(info,RTCmd_PurgeRxFifo);
1485 icount->overrun++;
1486 }
1487
1488 /* discard char if tty control flags say so */
1489 if (status & info->ignore_status_mask)
1490 continue;
1491
1492 status &= info->read_status_mask;
1493
1494 if (status & RXSTATUS_BREAK_RECEIVED) {
1495 flag = TTY_BREAK;
1496 if (info->port.flags & ASYNC_SAK)
1497 do_SAK(info->port.tty);
1498 } else if (status & RXSTATUS_PARITY_ERROR)
1499 flag = TTY_PARITY;
1500 else if (status & RXSTATUS_FRAMING_ERROR)
1501 flag = TTY_FRAME;
1502 } /* end of if (error) */
1503 tty_insert_flip_char(&info->port, DataByte, flag);
1504 if (status & RXSTATUS_OVERRUN) {
1505 /* Overrun is special, since it's
1506 * reported immediately, and doesn't
1507 * affect the current character
1508 */
1509 work += tty_insert_flip_char(&info->port, 0, TTY_OVERRUN);
1510 }
1511 }
1512
1513 if ( debug_level >= DEBUG_LEVEL_ISR ) {
1514 printk("%s(%d):rx=%d brk=%d parity=%d frame=%d overrun=%d\n",
1515 __FILE__,__LINE__,icount->rx,icount->brk,
1516 icount->parity,icount->frame,icount->overrun);
1517 }
1518
1519 if(work)
1520 tty_flip_buffer_push(&info->port);
1521}
1522
1523/* mgsl_isr_misc()
1524 *
1525 * Service a miscellaneous interrupt source.
1526 *
1527 * Arguments: info pointer to device extension (instance data)
1528 * Return Value: None
1529 */
1530static void mgsl_isr_misc( struct mgsl_struct *info )
1531{
1532 u16 status = usc_InReg( info, MISR );
1533
1534 if ( debug_level >= DEBUG_LEVEL_ISR )
1535 printk("%s(%d):mgsl_isr_misc status=%04X\n",
1536 __FILE__,__LINE__,status);
1537
1538 if ((status & MISCSTATUS_RCC_UNDERRUN) &&
1539 (info->params.mode == MGSL_MODE_HDLC)) {
1540
1541 /* turn off receiver and rx DMA */
1542 usc_EnableReceiver(info,DISABLE_UNCONDITIONAL);
1543 usc_DmaCmd(info, DmaCmd_ResetRxChannel);
1544 usc_UnlatchRxstatusBits(info, RXSTATUS_ALL);
1545 usc_ClearIrqPendingBits(info, RECEIVE_DATA | RECEIVE_STATUS);
1546 usc_DisableInterrupts(info, RECEIVE_DATA | RECEIVE_STATUS);
1547
1548 /* schedule BH handler to restart receiver */
1549 info->pending_bh |= BH_RECEIVE;
1550 info->rx_rcc_underrun = true;
1551 }
1552
1553 usc_ClearIrqPendingBits( info, MISC );
1554 usc_UnlatchMiscstatusBits( info, status );
1555
1556} /* end of mgsl_isr_misc() */
1557
1558/* mgsl_isr_null()
1559 *
1560 * Services undefined interrupt vectors from the
1561 * USC. (hence this function SHOULD never be called)
1562 *
1563 * Arguments: info pointer to device extension (instance data)
1564 * Return Value: None
1565 */
1566static void mgsl_isr_null( struct mgsl_struct *info )
1567{
1568
1569} /* end of mgsl_isr_null() */
1570
1571/* mgsl_isr_receive_dma()
1572 *
1573 * Service a receive DMA channel interrupt.
1574 * For this driver there are two sources of receive DMA interrupts
1575 * as identified in the Receive DMA mode Register (RDMR):
1576 *
1577 * BIT3 EOA/EOL End of List, all receive buffers in receive
1578 * buffer list have been filled (no more free buffers
1579 * available). The DMA controller has shut down.
1580 *
1581 * BIT2 EOB End of Buffer. This interrupt occurs when a receive
1582 * DMA buffer is terminated in response to completion
1583 * of a good frame or a frame with errors. The status
1584 * of the frame is stored in the buffer entry in the
1585 * list of receive buffer entries.
1586 *
1587 * Arguments: info pointer to device instance data
1588 * Return Value: None
1589 */
1590static void mgsl_isr_receive_dma( struct mgsl_struct *info )
1591{
1592 u16 status;
1593
1594 /* clear interrupt pending and IUS bit for Rx DMA IRQ */
1595 usc_OutDmaReg( info, CDIR, BIT9 | BIT1 );
1596
1597 /* Read the receive DMA status to identify interrupt type. */
1598 /* This also clears the status bits. */
1599 status = usc_InDmaReg( info, RDMR );
1600
1601 if ( debug_level >= DEBUG_LEVEL_ISR )
1602 printk("%s(%d):mgsl_isr_receive_dma(%s) status=%04X\n",
1603 __FILE__,__LINE__,info->device_name,status);
1604
1605 info->pending_bh |= BH_RECEIVE;
1606
1607 if ( status & BIT3 ) {
1608 info->rx_overflow = true;
1609 info->icount.buf_overrun++;
1610 }
1611
1612} /* end of mgsl_isr_receive_dma() */
1613
1614/* mgsl_isr_transmit_dma()
1615 *
1616 * This function services a transmit DMA channel interrupt.
1617 *
1618 * For this driver there is one source of transmit DMA interrupts
1619 * as identified in the Transmit DMA Mode Register (TDMR):
1620 *
1621 * BIT2 EOB End of Buffer. This interrupt occurs when a
1622 * transmit DMA buffer has been emptied.
1623 *
1624 * The driver maintains enough transmit DMA buffers to hold at least
1625 * one max frame size transmit frame. When operating in a buffered
1626 * transmit mode, there may be enough transmit DMA buffers to hold at
1627 * least two or more max frame size frames. On an EOB condition,
1628 * determine if there are any queued transmit buffers and copy into
1629 * transmit DMA buffers if we have room.
1630 *
1631 * Arguments: info pointer to device instance data
1632 * Return Value: None
1633 */
1634static void mgsl_isr_transmit_dma( struct mgsl_struct *info )
1635{
1636 u16 status;
1637
1638 /* clear interrupt pending and IUS bit for Tx DMA IRQ */
1639 usc_OutDmaReg(info, CDIR, BIT8 | BIT0 );
1640
1641 /* Read the transmit DMA status to identify interrupt type. */
1642 /* This also clears the status bits. */
1643
1644 status = usc_InDmaReg( info, TDMR );
1645
1646 if ( debug_level >= DEBUG_LEVEL_ISR )
1647 printk("%s(%d):mgsl_isr_transmit_dma(%s) status=%04X\n",
1648 __FILE__,__LINE__,info->device_name,status);
1649
1650 if ( status & BIT2 ) {
1651 --info->tx_dma_buffers_used;
1652
1653 /* if there are transmit frames queued,
1654 * try to load the next one
1655 */
1656 if ( load_next_tx_holding_buffer(info) ) {
1657 /* if call returns non-zero value, we have
1658 * at least one free tx holding buffer
1659 */
1660 info->pending_bh |= BH_TRANSMIT;
1661 }
1662 }
1663
1664} /* end of mgsl_isr_transmit_dma() */
1665
1666/* mgsl_interrupt()
1667 *
1668 * Interrupt service routine entry point.
1669 *
1670 * Arguments:
1671 *
1672 * irq interrupt number that caused interrupt
1673 * dev_id device ID supplied during interrupt registration
1674 *
1675 * Return Value: None
1676 */
1677static irqreturn_t mgsl_interrupt(int dummy, void *dev_id)
1678{
1679 struct mgsl_struct *info = dev_id;
1680 u16 UscVector;
1681 u16 DmaVector;
1682
1683 if ( debug_level >= DEBUG_LEVEL_ISR )
1684 printk(KERN_DEBUG "%s(%d):mgsl_interrupt(%d)entry.\n",
1685 __FILE__, __LINE__, info->irq_level);
1686
1687 spin_lock(&info->irq_spinlock);
1688
1689 for(;;) {
1690 /* Read the interrupt vectors from hardware. */
1691 UscVector = usc_InReg(info, IVR) >> 9;
1692 DmaVector = usc_InDmaReg(info, DIVR);
1693
1694 if ( debug_level >= DEBUG_LEVEL_ISR )
1695 printk("%s(%d):%s UscVector=%08X DmaVector=%08X\n",
1696 __FILE__,__LINE__,info->device_name,UscVector,DmaVector);
1697
1698 if ( !UscVector && !DmaVector )
1699 break;
1700
1701 /* Dispatch interrupt vector */
1702 if ( UscVector )
1703 (*UscIsrTable[UscVector])(info);
1704 else if ( (DmaVector&(BIT10|BIT9)) == BIT10)
1705 mgsl_isr_transmit_dma(info);
1706 else
1707 mgsl_isr_receive_dma(info);
1708
1709 if ( info->isr_overflow ) {
1710 printk(KERN_ERR "%s(%d):%s isr overflow irq=%d\n",
1711 __FILE__, __LINE__, info->device_name, info->irq_level);
1712 usc_DisableMasterIrqBit(info);
1713 usc_DisableDmaInterrupts(info,DICR_MASTER);
1714 break;
1715 }
1716 }
1717
1718 /* Request bottom half processing if there's something
1719 * for it to do and the bh is not already running
1720 */
1721
1722 if ( info->pending_bh && !info->bh_running && !info->bh_requested ) {
1723 if ( debug_level >= DEBUG_LEVEL_ISR )
1724 printk("%s(%d):%s queueing bh task.\n",
1725 __FILE__,__LINE__,info->device_name);
1726 schedule_work(&info->task);
1727 info->bh_requested = true;
1728 }
1729
1730 spin_unlock(&info->irq_spinlock);
1731
1732 if ( debug_level >= DEBUG_LEVEL_ISR )
1733 printk(KERN_DEBUG "%s(%d):mgsl_interrupt(%d)exit.\n",
1734 __FILE__, __LINE__, info->irq_level);
1735
1736 return IRQ_HANDLED;
1737} /* end of mgsl_interrupt() */
1738
1739/* startup()
1740 *
1741 * Initialize and start device.
1742 *
1743 * Arguments: info pointer to device instance data
1744 * Return Value: 0 if success, otherwise error code
1745 */
1746static int startup(struct mgsl_struct * info)
1747{
1748 int retval = 0;
1749
1750 if ( debug_level >= DEBUG_LEVEL_INFO )
1751 printk("%s(%d):mgsl_startup(%s)\n",__FILE__,__LINE__,info->device_name);
1752
1753 if (tty_port_initialized(&info->port))
1754 return 0;
1755
1756 if (!info->xmit_buf) {
1757 /* allocate a page of memory for a transmit buffer */
1758 info->xmit_buf = (unsigned char *)get_zeroed_page(GFP_KERNEL);
1759 if (!info->xmit_buf) {
1760 printk(KERN_ERR"%s(%d):%s can't allocate transmit buffer\n",
1761 __FILE__,__LINE__,info->device_name);
1762 return -ENOMEM;
1763 }
1764 }
1765
1766 info->pending_bh = 0;
1767
1768 memset(&info->icount, 0, sizeof(info->icount));
1769
1770 timer_setup(&info->tx_timer, mgsl_tx_timeout, 0);
1771
1772 /* Allocate and claim adapter resources */
1773 retval = mgsl_claim_resources(info);
1774
1775 /* perform existence check and diagnostics */
1776 if ( !retval )
1777 retval = mgsl_adapter_test(info);
1778
1779 if ( retval ) {
1780 if (capable(CAP_SYS_ADMIN) && info->port.tty)
1781 set_bit(TTY_IO_ERROR, &info->port.tty->flags);
1782 mgsl_release_resources(info);
1783 return retval;
1784 }
1785
1786 /* program hardware for current parameters */
1787 mgsl_change_params(info);
1788
1789 if (info->port.tty)
1790 clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
1791
1792 tty_port_set_initialized(&info->port, 1);
1793
1794 return 0;
1795} /* end of startup() */
1796
1797/* shutdown()
1798 *
1799 * Called by mgsl_close() and mgsl_hangup() to shutdown hardware
1800 *
1801 * Arguments: info pointer to device instance data
1802 * Return Value: None
1803 */
1804static void shutdown(struct mgsl_struct * info)
1805{
1806 unsigned long flags;
1807
1808 if (!tty_port_initialized(&info->port))
1809 return;
1810
1811 if (debug_level >= DEBUG_LEVEL_INFO)
1812 printk("%s(%d):mgsl_shutdown(%s)\n",
1813 __FILE__,__LINE__, info->device_name );
1814
1815 /* clear status wait queue because status changes */
1816 /* can't happen after shutting down the hardware */
1817 wake_up_interruptible(&info->status_event_wait_q);
1818 wake_up_interruptible(&info->event_wait_q);
1819
1820 del_timer_sync(&info->tx_timer);
1821
1822 if (info->xmit_buf) {
1823 free_page((unsigned long) info->xmit_buf);
1824 info->xmit_buf = NULL;
1825 }
1826
1827 spin_lock_irqsave(&info->irq_spinlock,flags);
1828 usc_DisableMasterIrqBit(info);
1829 usc_stop_receiver(info);
1830 usc_stop_transmitter(info);
1831 usc_DisableInterrupts(info,RECEIVE_DATA | RECEIVE_STATUS |
1832 TRANSMIT_DATA | TRANSMIT_STATUS | IO_PIN | MISC );
1833 usc_DisableDmaInterrupts(info,DICR_MASTER + DICR_TRANSMIT + DICR_RECEIVE);
1834
1835 /* Disable DMAEN (Port 7, Bit 14) */
1836 /* This disconnects the DMA request signal from the ISA bus */
1837 /* on the ISA adapter. This has no effect for the PCI adapter */
1838 usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT15) | BIT14));
1839
1840 /* Disable INTEN (Port 6, Bit12) */
1841 /* This disconnects the IRQ request signal to the ISA bus */
1842 /* on the ISA adapter. This has no effect for the PCI adapter */
1843 usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT13) | BIT12));
1844
1845 if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) {
1846 info->serial_signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
1847 usc_set_serial_signals(info);
1848 }
1849
1850 spin_unlock_irqrestore(&info->irq_spinlock,flags);
1851
1852 mgsl_release_resources(info);
1853
1854 if (info->port.tty)
1855 set_bit(TTY_IO_ERROR, &info->port.tty->flags);
1856
1857 tty_port_set_initialized(&info->port, 0);
1858} /* end of shutdown() */
1859
1860static void mgsl_program_hw(struct mgsl_struct *info)
1861{
1862 unsigned long flags;
1863
1864 spin_lock_irqsave(&info->irq_spinlock,flags);
1865
1866 usc_stop_receiver(info);
1867 usc_stop_transmitter(info);
1868 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
1869
1870 if (info->params.mode == MGSL_MODE_HDLC ||
1871 info->params.mode == MGSL_MODE_RAW ||
1872 info->netcount)
1873 usc_set_sync_mode(info);
1874 else
1875 usc_set_async_mode(info);
1876
1877 usc_set_serial_signals(info);
1878
1879 info->dcd_chkcount = 0;
1880 info->cts_chkcount = 0;
1881 info->ri_chkcount = 0;
1882 info->dsr_chkcount = 0;
1883
1884 usc_EnableStatusIrqs(info,SICR_CTS+SICR_DSR+SICR_DCD+SICR_RI);
1885 usc_EnableInterrupts(info, IO_PIN);
1886 usc_get_serial_signals(info);
1887
1888 if (info->netcount || info->port.tty->termios.c_cflag & CREAD)
1889 usc_start_receiver(info);
1890
1891 spin_unlock_irqrestore(&info->irq_spinlock,flags);
1892}
1893
1894/* Reconfigure adapter based on new parameters
1895 */
1896static void mgsl_change_params(struct mgsl_struct *info)
1897{
1898 unsigned cflag;
1899 int bits_per_char;
1900
1901 if (!info->port.tty)
1902 return;
1903
1904 if (debug_level >= DEBUG_LEVEL_INFO)
1905 printk("%s(%d):mgsl_change_params(%s)\n",
1906 __FILE__,__LINE__, info->device_name );
1907
1908 cflag = info->port.tty->termios.c_cflag;
1909
1910 /* if B0 rate (hangup) specified then negate RTS and DTR */
1911 /* otherwise assert RTS and DTR */
1912 if (cflag & CBAUD)
1913 info->serial_signals |= SerialSignal_RTS | SerialSignal_DTR;
1914 else
1915 info->serial_signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
1916
1917 /* byte size and parity */
1918
1919 switch (cflag & CSIZE) {
1920 case CS5: info->params.data_bits = 5; break;
1921 case CS6: info->params.data_bits = 6; break;
1922 case CS7: info->params.data_bits = 7; break;
1923 case CS8: info->params.data_bits = 8; break;
1924 /* Never happens, but GCC is too dumb to figure it out */
1925 default: info->params.data_bits = 7; break;
1926 }
1927
1928 if (cflag & CSTOPB)
1929 info->params.stop_bits = 2;
1930 else
1931 info->params.stop_bits = 1;
1932
1933 info->params.parity = ASYNC_PARITY_NONE;
1934 if (cflag & PARENB) {
1935 if (cflag & PARODD)
1936 info->params.parity = ASYNC_PARITY_ODD;
1937 else
1938 info->params.parity = ASYNC_PARITY_EVEN;
1939#ifdef CMSPAR
1940 if (cflag & CMSPAR)
1941 info->params.parity = ASYNC_PARITY_SPACE;
1942#endif
1943 }
1944
1945 /* calculate number of jiffies to transmit a full
1946 * FIFO (32 bytes) at specified data rate
1947 */
1948 bits_per_char = info->params.data_bits +
1949 info->params.stop_bits + 1;
1950
1951 /* if port data rate is set to 460800 or less then
1952 * allow tty settings to override, otherwise keep the
1953 * current data rate.
1954 */
1955 if (info->params.data_rate <= 460800)
1956 info->params.data_rate = tty_get_baud_rate(info->port.tty);
1957
1958 if ( info->params.data_rate ) {
1959 info->timeout = (32*HZ*bits_per_char) /
1960 info->params.data_rate;
1961 }
1962 info->timeout += HZ/50; /* Add .02 seconds of slop */
1963
1964 tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
1965 tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
1966
1967 /* process tty input control flags */
1968
1969 info->read_status_mask = RXSTATUS_OVERRUN;
1970 if (I_INPCK(info->port.tty))
1971 info->read_status_mask |= RXSTATUS_PARITY_ERROR | RXSTATUS_FRAMING_ERROR;
1972 if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
1973 info->read_status_mask |= RXSTATUS_BREAK_RECEIVED;
1974
1975 if (I_IGNPAR(info->port.tty))
1976 info->ignore_status_mask |= RXSTATUS_PARITY_ERROR | RXSTATUS_FRAMING_ERROR;
1977 if (I_IGNBRK(info->port.tty)) {
1978 info->ignore_status_mask |= RXSTATUS_BREAK_RECEIVED;
1979 /* If ignoring parity and break indicators, ignore
1980 * overruns too. (For real raw support).
1981 */
1982 if (I_IGNPAR(info->port.tty))
1983 info->ignore_status_mask |= RXSTATUS_OVERRUN;
1984 }
1985
1986 mgsl_program_hw(info);
1987
1988} /* end of mgsl_change_params() */
1989
1990/* mgsl_put_char()
1991 *
1992 * Add a character to the transmit buffer.
1993 *
1994 * Arguments: tty pointer to tty information structure
1995 * ch character to add to transmit buffer
1996 *
1997 * Return Value: None
1998 */
1999static int mgsl_put_char(struct tty_struct *tty, unsigned char ch)
2000{
2001 struct mgsl_struct *info = tty->driver_data;
2002 unsigned long flags;
2003 int ret = 0;
2004
2005 if (debug_level >= DEBUG_LEVEL_INFO) {
2006 printk(KERN_DEBUG "%s(%d):mgsl_put_char(%d) on %s\n",
2007 __FILE__, __LINE__, ch, info->device_name);
2008 }
2009
2010 if (mgsl_paranoia_check(info, tty->name, "mgsl_put_char"))
2011 return 0;
2012
2013 if (!info->xmit_buf)
2014 return 0;
2015
2016 spin_lock_irqsave(&info->irq_spinlock, flags);
2017
2018 if ((info->params.mode == MGSL_MODE_ASYNC ) || !info->tx_active) {
2019 if (info->xmit_cnt < SERIAL_XMIT_SIZE - 1) {
2020 info->xmit_buf[info->xmit_head++] = ch;
2021 info->xmit_head &= SERIAL_XMIT_SIZE-1;
2022 info->xmit_cnt++;
2023 ret = 1;
2024 }
2025 }
2026 spin_unlock_irqrestore(&info->irq_spinlock, flags);
2027 return ret;
2028
2029} /* end of mgsl_put_char() */
2030
2031/* mgsl_flush_chars()
2032 *
2033 * Enable transmitter so remaining characters in the
2034 * transmit buffer are sent.
2035 *
2036 * Arguments: tty pointer to tty information structure
2037 * Return Value: None
2038 */
2039static void mgsl_flush_chars(struct tty_struct *tty)
2040{
2041 struct mgsl_struct *info = tty->driver_data;
2042 unsigned long flags;
2043
2044 if ( debug_level >= DEBUG_LEVEL_INFO )
2045 printk( "%s(%d):mgsl_flush_chars() entry on %s xmit_cnt=%d\n",
2046 __FILE__,__LINE__,info->device_name,info->xmit_cnt);
2047
2048 if (mgsl_paranoia_check(info, tty->name, "mgsl_flush_chars"))
2049 return;
2050
2051 if (info->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped ||
2052 !info->xmit_buf)
2053 return;
2054
2055 if ( debug_level >= DEBUG_LEVEL_INFO )
2056 printk( "%s(%d):mgsl_flush_chars() entry on %s starting transmitter\n",
2057 __FILE__,__LINE__,info->device_name );
2058
2059 spin_lock_irqsave(&info->irq_spinlock,flags);
2060
2061 if (!info->tx_active) {
2062 if ( (info->params.mode == MGSL_MODE_HDLC ||
2063 info->params.mode == MGSL_MODE_RAW) && info->xmit_cnt ) {
2064 /* operating in synchronous (frame oriented) mode */
2065 /* copy data from circular xmit_buf to */
2066 /* transmit DMA buffer. */
2067 mgsl_load_tx_dma_buffer(info,
2068 info->xmit_buf,info->xmit_cnt);
2069 }
2070 usc_start_transmitter(info);
2071 }
2072
2073 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2074
2075} /* end of mgsl_flush_chars() */
2076
2077/* mgsl_write()
2078 *
2079 * Send a block of data
2080 *
2081 * Arguments:
2082 *
2083 * tty pointer to tty information structure
2084 * buf pointer to buffer containing send data
2085 * count size of send data in bytes
2086 *
2087 * Return Value: number of characters written
2088 */
2089static int mgsl_write(struct tty_struct * tty,
2090 const unsigned char *buf, int count)
2091{
2092 int c, ret = 0;
2093 struct mgsl_struct *info = tty->driver_data;
2094 unsigned long flags;
2095
2096 if ( debug_level >= DEBUG_LEVEL_INFO )
2097 printk( "%s(%d):mgsl_write(%s) count=%d\n",
2098 __FILE__,__LINE__,info->device_name,count);
2099
2100 if (mgsl_paranoia_check(info, tty->name, "mgsl_write"))
2101 goto cleanup;
2102
2103 if (!info->xmit_buf)
2104 goto cleanup;
2105
2106 if ( info->params.mode == MGSL_MODE_HDLC ||
2107 info->params.mode == MGSL_MODE_RAW ) {
2108 /* operating in synchronous (frame oriented) mode */
2109 if (info->tx_active) {
2110
2111 if ( info->params.mode == MGSL_MODE_HDLC ) {
2112 ret = 0;
2113 goto cleanup;
2114 }
2115 /* transmitter is actively sending data -
2116 * if we have multiple transmit dma and
2117 * holding buffers, attempt to queue this
2118 * frame for transmission at a later time.
2119 */
2120 if (info->tx_holding_count >= info->num_tx_holding_buffers ) {
2121 /* no tx holding buffers available */
2122 ret = 0;
2123 goto cleanup;
2124 }
2125
2126 /* queue transmit frame request */
2127 ret = count;
2128 save_tx_buffer_request(info,buf,count);
2129
2130 /* if we have sufficient tx dma buffers,
2131 * load the next buffered tx request
2132 */
2133 spin_lock_irqsave(&info->irq_spinlock,flags);
2134 load_next_tx_holding_buffer(info);
2135 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2136 goto cleanup;
2137 }
2138
2139 /* if operating in HDLC LoopMode and the adapter */
2140 /* has yet to be inserted into the loop, we can't */
2141 /* transmit */
2142
2143 if ( (info->params.flags & HDLC_FLAG_HDLC_LOOPMODE) &&
2144 !usc_loopmode_active(info) )
2145 {
2146 ret = 0;
2147 goto cleanup;
2148 }
2149
2150 if ( info->xmit_cnt ) {
2151 /* Send accumulated from send_char() calls */
2152 /* as frame and wait before accepting more data. */
2153 ret = 0;
2154
2155 /* copy data from circular xmit_buf to */
2156 /* transmit DMA buffer. */
2157 mgsl_load_tx_dma_buffer(info,
2158 info->xmit_buf,info->xmit_cnt);
2159 if ( debug_level >= DEBUG_LEVEL_INFO )
2160 printk( "%s(%d):mgsl_write(%s) sync xmit_cnt flushing\n",
2161 __FILE__,__LINE__,info->device_name);
2162 } else {
2163 if ( debug_level >= DEBUG_LEVEL_INFO )
2164 printk( "%s(%d):mgsl_write(%s) sync transmit accepted\n",
2165 __FILE__,__LINE__,info->device_name);
2166 ret = count;
2167 info->xmit_cnt = count;
2168 mgsl_load_tx_dma_buffer(info,buf,count);
2169 }
2170 } else {
2171 while (1) {
2172 spin_lock_irqsave(&info->irq_spinlock,flags);
2173 c = min_t(int, count,
2174 min(SERIAL_XMIT_SIZE - info->xmit_cnt - 1,
2175 SERIAL_XMIT_SIZE - info->xmit_head));
2176 if (c <= 0) {
2177 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2178 break;
2179 }
2180 memcpy(info->xmit_buf + info->xmit_head, buf, c);
2181 info->xmit_head = ((info->xmit_head + c) &
2182 (SERIAL_XMIT_SIZE-1));
2183 info->xmit_cnt += c;
2184 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2185 buf += c;
2186 count -= c;
2187 ret += c;
2188 }
2189 }
2190
2191 if (info->xmit_cnt && !tty->stopped && !tty->hw_stopped) {
2192 spin_lock_irqsave(&info->irq_spinlock,flags);
2193 if (!info->tx_active)
2194 usc_start_transmitter(info);
2195 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2196 }
2197cleanup:
2198 if ( debug_level >= DEBUG_LEVEL_INFO )
2199 printk( "%s(%d):mgsl_write(%s) returning=%d\n",
2200 __FILE__,__LINE__,info->device_name,ret);
2201
2202 return ret;
2203
2204} /* end of mgsl_write() */
2205
2206/* mgsl_write_room()
2207 *
2208 * Return the count of free bytes in transmit buffer
2209 *
2210 * Arguments: tty pointer to tty info structure
2211 * Return Value: None
2212 */
2213static int mgsl_write_room(struct tty_struct *tty)
2214{
2215 struct mgsl_struct *info = tty->driver_data;
2216 int ret;
2217
2218 if (mgsl_paranoia_check(info, tty->name, "mgsl_write_room"))
2219 return 0;
2220 ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1;
2221 if (ret < 0)
2222 ret = 0;
2223
2224 if (debug_level >= DEBUG_LEVEL_INFO)
2225 printk("%s(%d):mgsl_write_room(%s)=%d\n",
2226 __FILE__,__LINE__, info->device_name,ret );
2227
2228 if ( info->params.mode == MGSL_MODE_HDLC ||
2229 info->params.mode == MGSL_MODE_RAW ) {
2230 /* operating in synchronous (frame oriented) mode */
2231 if ( info->tx_active )
2232 return 0;
2233 else
2234 return HDLC_MAX_FRAME_SIZE;
2235 }
2236
2237 return ret;
2238
2239} /* end of mgsl_write_room() */
2240
2241/* mgsl_chars_in_buffer()
2242 *
2243 * Return the count of bytes in transmit buffer
2244 *
2245 * Arguments: tty pointer to tty info structure
2246 * Return Value: None
2247 */
2248static int mgsl_chars_in_buffer(struct tty_struct *tty)
2249{
2250 struct mgsl_struct *info = tty->driver_data;
2251
2252 if (debug_level >= DEBUG_LEVEL_INFO)
2253 printk("%s(%d):mgsl_chars_in_buffer(%s)\n",
2254 __FILE__,__LINE__, info->device_name );
2255
2256 if (mgsl_paranoia_check(info, tty->name, "mgsl_chars_in_buffer"))
2257 return 0;
2258
2259 if (debug_level >= DEBUG_LEVEL_INFO)
2260 printk("%s(%d):mgsl_chars_in_buffer(%s)=%d\n",
2261 __FILE__,__LINE__, info->device_name,info->xmit_cnt );
2262
2263 if ( info->params.mode == MGSL_MODE_HDLC ||
2264 info->params.mode == MGSL_MODE_RAW ) {
2265 /* operating in synchronous (frame oriented) mode */
2266 if ( info->tx_active )
2267 return info->max_frame_size;
2268 else
2269 return 0;
2270 }
2271
2272 return info->xmit_cnt;
2273} /* end of mgsl_chars_in_buffer() */
2274
2275/* mgsl_flush_buffer()
2276 *
2277 * Discard all data in the send buffer
2278 *
2279 * Arguments: tty pointer to tty info structure
2280 * Return Value: None
2281 */
2282static void mgsl_flush_buffer(struct tty_struct *tty)
2283{
2284 struct mgsl_struct *info = tty->driver_data;
2285 unsigned long flags;
2286
2287 if (debug_level >= DEBUG_LEVEL_INFO)
2288 printk("%s(%d):mgsl_flush_buffer(%s) entry\n",
2289 __FILE__,__LINE__, info->device_name );
2290
2291 if (mgsl_paranoia_check(info, tty->name, "mgsl_flush_buffer"))
2292 return;
2293
2294 spin_lock_irqsave(&info->irq_spinlock,flags);
2295 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
2296 del_timer(&info->tx_timer);
2297 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2298
2299 tty_wakeup(tty);
2300}
2301
2302/* mgsl_send_xchar()
2303 *
2304 * Send a high-priority XON/XOFF character
2305 *
2306 * Arguments: tty pointer to tty info structure
2307 * ch character to send
2308 * Return Value: None
2309 */
2310static void mgsl_send_xchar(struct tty_struct *tty, char ch)
2311{
2312 struct mgsl_struct *info = tty->driver_data;
2313 unsigned long flags;
2314
2315 if (debug_level >= DEBUG_LEVEL_INFO)
2316 printk("%s(%d):mgsl_send_xchar(%s,%d)\n",
2317 __FILE__,__LINE__, info->device_name, ch );
2318
2319 if (mgsl_paranoia_check(info, tty->name, "mgsl_send_xchar"))
2320 return;
2321
2322 info->x_char = ch;
2323 if (ch) {
2324 /* Make sure transmit interrupts are on */
2325 spin_lock_irqsave(&info->irq_spinlock,flags);
2326 if (!info->tx_enabled)
2327 usc_start_transmitter(info);
2328 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2329 }
2330} /* end of mgsl_send_xchar() */
2331
2332/* mgsl_throttle()
2333 *
2334 * Signal remote device to throttle send data (our receive data)
2335 *
2336 * Arguments: tty pointer to tty info structure
2337 * Return Value: None
2338 */
2339static void mgsl_throttle(struct tty_struct * tty)
2340{
2341 struct mgsl_struct *info = tty->driver_data;
2342 unsigned long flags;
2343
2344 if (debug_level >= DEBUG_LEVEL_INFO)
2345 printk("%s(%d):mgsl_throttle(%s) entry\n",
2346 __FILE__,__LINE__, info->device_name );
2347
2348 if (mgsl_paranoia_check(info, tty->name, "mgsl_throttle"))
2349 return;
2350
2351 if (I_IXOFF(tty))
2352 mgsl_send_xchar(tty, STOP_CHAR(tty));
2353
2354 if (C_CRTSCTS(tty)) {
2355 spin_lock_irqsave(&info->irq_spinlock,flags);
2356 info->serial_signals &= ~SerialSignal_RTS;
2357 usc_set_serial_signals(info);
2358 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2359 }
2360} /* end of mgsl_throttle() */
2361
2362/* mgsl_unthrottle()
2363 *
2364 * Signal remote device to stop throttling send data (our receive data)
2365 *
2366 * Arguments: tty pointer to tty info structure
2367 * Return Value: None
2368 */
2369static void mgsl_unthrottle(struct tty_struct * tty)
2370{
2371 struct mgsl_struct *info = tty->driver_data;
2372 unsigned long flags;
2373
2374 if (debug_level >= DEBUG_LEVEL_INFO)
2375 printk("%s(%d):mgsl_unthrottle(%s) entry\n",
2376 __FILE__,__LINE__, info->device_name );
2377
2378 if (mgsl_paranoia_check(info, tty->name, "mgsl_unthrottle"))
2379 return;
2380
2381 if (I_IXOFF(tty)) {
2382 if (info->x_char)
2383 info->x_char = 0;
2384 else
2385 mgsl_send_xchar(tty, START_CHAR(tty));
2386 }
2387
2388 if (C_CRTSCTS(tty)) {
2389 spin_lock_irqsave(&info->irq_spinlock,flags);
2390 info->serial_signals |= SerialSignal_RTS;
2391 usc_set_serial_signals(info);
2392 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2393 }
2394
2395} /* end of mgsl_unthrottle() */
2396
2397/* mgsl_get_stats()
2398 *
2399 * get the current serial parameters information
2400 *
2401 * Arguments: info pointer to device instance data
2402 * user_icount pointer to buffer to hold returned stats
2403 *
2404 * Return Value: 0 if success, otherwise error code
2405 */
2406static int mgsl_get_stats(struct mgsl_struct * info, struct mgsl_icount __user *user_icount)
2407{
2408 int err;
2409
2410 if (debug_level >= DEBUG_LEVEL_INFO)
2411 printk("%s(%d):mgsl_get_params(%s)\n",
2412 __FILE__,__LINE__, info->device_name);
2413
2414 if (!user_icount) {
2415 memset(&info->icount, 0, sizeof(info->icount));
2416 } else {
2417 mutex_lock(&info->port.mutex);
2418 COPY_TO_USER(err, user_icount, &info->icount, sizeof(struct mgsl_icount));
2419 mutex_unlock(&info->port.mutex);
2420 if (err)
2421 return -EFAULT;
2422 }
2423
2424 return 0;
2425
2426} /* end of mgsl_get_stats() */
2427
2428/* mgsl_get_params()
2429 *
2430 * get the current serial parameters information
2431 *
2432 * Arguments: info pointer to device instance data
2433 * user_params pointer to buffer to hold returned params
2434 *
2435 * Return Value: 0 if success, otherwise error code
2436 */
2437static int mgsl_get_params(struct mgsl_struct * info, MGSL_PARAMS __user *user_params)
2438{
2439 int err;
2440 if (debug_level >= DEBUG_LEVEL_INFO)
2441 printk("%s(%d):mgsl_get_params(%s)\n",
2442 __FILE__,__LINE__, info->device_name);
2443
2444 mutex_lock(&info->port.mutex);
2445 COPY_TO_USER(err,user_params, &info->params, sizeof(MGSL_PARAMS));
2446 mutex_unlock(&info->port.mutex);
2447 if (err) {
2448 if ( debug_level >= DEBUG_LEVEL_INFO )
2449 printk( "%s(%d):mgsl_get_params(%s) user buffer copy failed\n",
2450 __FILE__,__LINE__,info->device_name);
2451 return -EFAULT;
2452 }
2453
2454 return 0;
2455
2456} /* end of mgsl_get_params() */
2457
2458/* mgsl_set_params()
2459 *
2460 * set the serial parameters
2461 *
2462 * Arguments:
2463 *
2464 * info pointer to device instance data
2465 * new_params user buffer containing new serial params
2466 *
2467 * Return Value: 0 if success, otherwise error code
2468 */
2469static int mgsl_set_params(struct mgsl_struct * info, MGSL_PARAMS __user *new_params)
2470{
2471 unsigned long flags;
2472 MGSL_PARAMS tmp_params;
2473 int err;
2474
2475 if (debug_level >= DEBUG_LEVEL_INFO)
2476 printk("%s(%d):mgsl_set_params %s\n", __FILE__,__LINE__,
2477 info->device_name );
2478 COPY_FROM_USER(err,&tmp_params, new_params, sizeof(MGSL_PARAMS));
2479 if (err) {
2480 if ( debug_level >= DEBUG_LEVEL_INFO )
2481 printk( "%s(%d):mgsl_set_params(%s) user buffer copy failed\n",
2482 __FILE__,__LINE__,info->device_name);
2483 return -EFAULT;
2484 }
2485
2486 mutex_lock(&info->port.mutex);
2487 spin_lock_irqsave(&info->irq_spinlock,flags);
2488 memcpy(&info->params,&tmp_params,sizeof(MGSL_PARAMS));
2489 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2490
2491 mgsl_change_params(info);
2492 mutex_unlock(&info->port.mutex);
2493
2494 return 0;
2495
2496} /* end of mgsl_set_params() */
2497
2498/* mgsl_get_txidle()
2499 *
2500 * get the current transmit idle mode
2501 *
2502 * Arguments: info pointer to device instance data
2503 * idle_mode pointer to buffer to hold returned idle mode
2504 *
2505 * Return Value: 0 if success, otherwise error code
2506 */
2507static int mgsl_get_txidle(struct mgsl_struct * info, int __user *idle_mode)
2508{
2509 int err;
2510
2511 if (debug_level >= DEBUG_LEVEL_INFO)
2512 printk("%s(%d):mgsl_get_txidle(%s)=%d\n",
2513 __FILE__,__LINE__, info->device_name, info->idle_mode);
2514
2515 COPY_TO_USER(err,idle_mode, &info->idle_mode, sizeof(int));
2516 if (err) {
2517 if ( debug_level >= DEBUG_LEVEL_INFO )
2518 printk( "%s(%d):mgsl_get_txidle(%s) user buffer copy failed\n",
2519 __FILE__,__LINE__,info->device_name);
2520 return -EFAULT;
2521 }
2522
2523 return 0;
2524
2525} /* end of mgsl_get_txidle() */
2526
2527/* mgsl_set_txidle() service ioctl to set transmit idle mode
2528 *
2529 * Arguments: info pointer to device instance data
2530 * idle_mode new idle mode
2531 *
2532 * Return Value: 0 if success, otherwise error code
2533 */
2534static int mgsl_set_txidle(struct mgsl_struct * info, int idle_mode)
2535{
2536 unsigned long flags;
2537
2538 if (debug_level >= DEBUG_LEVEL_INFO)
2539 printk("%s(%d):mgsl_set_txidle(%s,%d)\n", __FILE__,__LINE__,
2540 info->device_name, idle_mode );
2541
2542 spin_lock_irqsave(&info->irq_spinlock,flags);
2543 info->idle_mode = idle_mode;
2544 usc_set_txidle( info );
2545 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2546 return 0;
2547
2548} /* end of mgsl_set_txidle() */
2549
2550/* mgsl_txenable()
2551 *
2552 * enable or disable the transmitter
2553 *
2554 * Arguments:
2555 *
2556 * info pointer to device instance data
2557 * enable 1 = enable, 0 = disable
2558 *
2559 * Return Value: 0 if success, otherwise error code
2560 */
2561static int mgsl_txenable(struct mgsl_struct * info, int enable)
2562{
2563 unsigned long flags;
2564
2565 if (debug_level >= DEBUG_LEVEL_INFO)
2566 printk("%s(%d):mgsl_txenable(%s,%d)\n", __FILE__,__LINE__,
2567 info->device_name, enable);
2568
2569 spin_lock_irqsave(&info->irq_spinlock,flags);
2570 if ( enable ) {
2571 if ( !info->tx_enabled ) {
2572
2573 usc_start_transmitter(info);
2574 /*--------------------------------------------------
2575 * if HDLC/SDLC Loop mode, attempt to insert the
2576 * station in the 'loop' by setting CMR:13. Upon
2577 * receipt of the next GoAhead (RxAbort) sequence,
2578 * the OnLoop indicator (CCSR:7) should go active
2579 * to indicate that we are on the loop
2580 *--------------------------------------------------*/
2581 if ( info->params.flags & HDLC_FLAG_HDLC_LOOPMODE )
2582 usc_loopmode_insert_request( info );
2583 }
2584 } else {
2585 if ( info->tx_enabled )
2586 usc_stop_transmitter(info);
2587 }
2588 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2589 return 0;
2590
2591} /* end of mgsl_txenable() */
2592
2593/* mgsl_txabort() abort send HDLC frame
2594 *
2595 * Arguments: info pointer to device instance data
2596 * Return Value: 0 if success, otherwise error code
2597 */
2598static int mgsl_txabort(struct mgsl_struct * info)
2599{
2600 unsigned long flags;
2601
2602 if (debug_level >= DEBUG_LEVEL_INFO)
2603 printk("%s(%d):mgsl_txabort(%s)\n", __FILE__,__LINE__,
2604 info->device_name);
2605
2606 spin_lock_irqsave(&info->irq_spinlock,flags);
2607 if ( info->tx_active && info->params.mode == MGSL_MODE_HDLC )
2608 {
2609 if ( info->params.flags & HDLC_FLAG_HDLC_LOOPMODE )
2610 usc_loopmode_cancel_transmit( info );
2611 else
2612 usc_TCmd(info,TCmd_SendAbort);
2613 }
2614 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2615 return 0;
2616
2617} /* end of mgsl_txabort() */
2618
2619/* mgsl_rxenable() enable or disable the receiver
2620 *
2621 * Arguments: info pointer to device instance data
2622 * enable 1 = enable, 0 = disable
2623 * Return Value: 0 if success, otherwise error code
2624 */
2625static int mgsl_rxenable(struct mgsl_struct * info, int enable)
2626{
2627 unsigned long flags;
2628
2629 if (debug_level >= DEBUG_LEVEL_INFO)
2630 printk("%s(%d):mgsl_rxenable(%s,%d)\n", __FILE__,__LINE__,
2631 info->device_name, enable);
2632
2633 spin_lock_irqsave(&info->irq_spinlock,flags);
2634 if ( enable ) {
2635 if ( !info->rx_enabled )
2636 usc_start_receiver(info);
2637 } else {
2638 if ( info->rx_enabled )
2639 usc_stop_receiver(info);
2640 }
2641 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2642 return 0;
2643
2644} /* end of mgsl_rxenable() */
2645
2646/* mgsl_wait_event() wait for specified event to occur
2647 *
2648 * Arguments: info pointer to device instance data
2649 * mask pointer to bitmask of events to wait for
2650 * Return Value: 0 if successful and bit mask updated with
2651 * of events triggerred,
2652 * otherwise error code
2653 */
2654static int mgsl_wait_event(struct mgsl_struct * info, int __user * mask_ptr)
2655{
2656 unsigned long flags;
2657 int s;
2658 int rc=0;
2659 struct mgsl_icount cprev, cnow;
2660 int events;
2661 int mask;
2662 struct _input_signal_events oldsigs, newsigs;
2663 DECLARE_WAITQUEUE(wait, current);
2664
2665 COPY_FROM_USER(rc,&mask, mask_ptr, sizeof(int));
2666 if (rc) {
2667 return -EFAULT;
2668 }
2669
2670 if (debug_level >= DEBUG_LEVEL_INFO)
2671 printk("%s(%d):mgsl_wait_event(%s,%d)\n", __FILE__,__LINE__,
2672 info->device_name, mask);
2673
2674 spin_lock_irqsave(&info->irq_spinlock,flags);
2675
2676 /* return immediately if state matches requested events */
2677 usc_get_serial_signals(info);
2678 s = info->serial_signals;
2679 events = mask &
2680 ( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) +
2681 ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) +
2682 ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) +
2683 ((s & SerialSignal_RI) ? MgslEvent_RiActive :MgslEvent_RiInactive) );
2684 if (events) {
2685 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2686 goto exit;
2687 }
2688
2689 /* save current irq counts */
2690 cprev = info->icount;
2691 oldsigs = info->input_signal_events;
2692
2693 /* enable hunt and idle irqs if needed */
2694 if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) {
2695 u16 oldreg = usc_InReg(info,RICR);
2696 u16 newreg = oldreg +
2697 (mask & MgslEvent_ExitHuntMode ? RXSTATUS_EXITED_HUNT:0) +
2698 (mask & MgslEvent_IdleReceived ? RXSTATUS_IDLE_RECEIVED:0);
2699 if (oldreg != newreg)
2700 usc_OutReg(info, RICR, newreg);
2701 }
2702
2703 set_current_state(TASK_INTERRUPTIBLE);
2704 add_wait_queue(&info->event_wait_q, &wait);
2705
2706 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2707
2708
2709 for(;;) {
2710 schedule();
2711 if (signal_pending(current)) {
2712 rc = -ERESTARTSYS;
2713 break;
2714 }
2715
2716 /* get current irq counts */
2717 spin_lock_irqsave(&info->irq_spinlock,flags);
2718 cnow = info->icount;
2719 newsigs = info->input_signal_events;
2720 set_current_state(TASK_INTERRUPTIBLE);
2721 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2722
2723 /* if no change, wait aborted for some reason */
2724 if (newsigs.dsr_up == oldsigs.dsr_up &&
2725 newsigs.dsr_down == oldsigs.dsr_down &&
2726 newsigs.dcd_up == oldsigs.dcd_up &&
2727 newsigs.dcd_down == oldsigs.dcd_down &&
2728 newsigs.cts_up == oldsigs.cts_up &&
2729 newsigs.cts_down == oldsigs.cts_down &&
2730 newsigs.ri_up == oldsigs.ri_up &&
2731 newsigs.ri_down == oldsigs.ri_down &&
2732 cnow.exithunt == cprev.exithunt &&
2733 cnow.rxidle == cprev.rxidle) {
2734 rc = -EIO;
2735 break;
2736 }
2737
2738 events = mask &
2739 ( (newsigs.dsr_up != oldsigs.dsr_up ? MgslEvent_DsrActive:0) +
2740 (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) +
2741 (newsigs.dcd_up != oldsigs.dcd_up ? MgslEvent_DcdActive:0) +
2742 (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) +
2743 (newsigs.cts_up != oldsigs.cts_up ? MgslEvent_CtsActive:0) +
2744 (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) +
2745 (newsigs.ri_up != oldsigs.ri_up ? MgslEvent_RiActive:0) +
2746 (newsigs.ri_down != oldsigs.ri_down ? MgslEvent_RiInactive:0) +
2747 (cnow.exithunt != cprev.exithunt ? MgslEvent_ExitHuntMode:0) +
2748 (cnow.rxidle != cprev.rxidle ? MgslEvent_IdleReceived:0) );
2749 if (events)
2750 break;
2751
2752 cprev = cnow;
2753 oldsigs = newsigs;
2754 }
2755
2756 remove_wait_queue(&info->event_wait_q, &wait);
2757 set_current_state(TASK_RUNNING);
2758
2759 if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) {
2760 spin_lock_irqsave(&info->irq_spinlock,flags);
2761 if (!waitqueue_active(&info->event_wait_q)) {
2762 /* disable enable exit hunt mode/idle rcvd IRQs */
2763 usc_OutReg(info, RICR, usc_InReg(info,RICR) &
2764 ~(RXSTATUS_EXITED_HUNT | RXSTATUS_IDLE_RECEIVED));
2765 }
2766 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2767 }
2768exit:
2769 if ( rc == 0 )
2770 PUT_USER(rc, events, mask_ptr);
2771
2772 return rc;
2773
2774} /* end of mgsl_wait_event() */
2775
2776static int modem_input_wait(struct mgsl_struct *info,int arg)
2777{
2778 unsigned long flags;
2779 int rc;
2780 struct mgsl_icount cprev, cnow;
2781 DECLARE_WAITQUEUE(wait, current);
2782
2783 /* save current irq counts */
2784 spin_lock_irqsave(&info->irq_spinlock,flags);
2785 cprev = info->icount;
2786 add_wait_queue(&info->status_event_wait_q, &wait);
2787 set_current_state(TASK_INTERRUPTIBLE);
2788 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2789
2790 for(;;) {
2791 schedule();
2792 if (signal_pending(current)) {
2793 rc = -ERESTARTSYS;
2794 break;
2795 }
2796
2797 /* get new irq counts */
2798 spin_lock_irqsave(&info->irq_spinlock,flags);
2799 cnow = info->icount;
2800 set_current_state(TASK_INTERRUPTIBLE);
2801 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2802
2803 /* if no change, wait aborted for some reason */
2804 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
2805 cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) {
2806 rc = -EIO;
2807 break;
2808 }
2809
2810 /* check for change in caller specified modem input */
2811 if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) ||
2812 (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) ||
2813 (arg & TIOCM_CD && cnow.dcd != cprev.dcd) ||
2814 (arg & TIOCM_CTS && cnow.cts != cprev.cts)) {
2815 rc = 0;
2816 break;
2817 }
2818
2819 cprev = cnow;
2820 }
2821 remove_wait_queue(&info->status_event_wait_q, &wait);
2822 set_current_state(TASK_RUNNING);
2823 return rc;
2824}
2825
2826/* return the state of the serial control and status signals
2827 */
2828static int tiocmget(struct tty_struct *tty)
2829{
2830 struct mgsl_struct *info = tty->driver_data;
2831 unsigned int result;
2832 unsigned long flags;
2833
2834 spin_lock_irqsave(&info->irq_spinlock,flags);
2835 usc_get_serial_signals(info);
2836 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2837
2838 result = ((info->serial_signals & SerialSignal_RTS) ? TIOCM_RTS:0) +
2839 ((info->serial_signals & SerialSignal_DTR) ? TIOCM_DTR:0) +
2840 ((info->serial_signals & SerialSignal_DCD) ? TIOCM_CAR:0) +
2841 ((info->serial_signals & SerialSignal_RI) ? TIOCM_RNG:0) +
2842 ((info->serial_signals & SerialSignal_DSR) ? TIOCM_DSR:0) +
2843 ((info->serial_signals & SerialSignal_CTS) ? TIOCM_CTS:0);
2844
2845 if (debug_level >= DEBUG_LEVEL_INFO)
2846 printk("%s(%d):%s tiocmget() value=%08X\n",
2847 __FILE__,__LINE__, info->device_name, result );
2848 return result;
2849}
2850
2851/* set modem control signals (DTR/RTS)
2852 */
2853static int tiocmset(struct tty_struct *tty,
2854 unsigned int set, unsigned int clear)
2855{
2856 struct mgsl_struct *info = tty->driver_data;
2857 unsigned long flags;
2858
2859 if (debug_level >= DEBUG_LEVEL_INFO)
2860 printk("%s(%d):%s tiocmset(%x,%x)\n",
2861 __FILE__,__LINE__,info->device_name, set, clear);
2862
2863 if (set & TIOCM_RTS)
2864 info->serial_signals |= SerialSignal_RTS;
2865 if (set & TIOCM_DTR)
2866 info->serial_signals |= SerialSignal_DTR;
2867 if (clear & TIOCM_RTS)
2868 info->serial_signals &= ~SerialSignal_RTS;
2869 if (clear & TIOCM_DTR)
2870 info->serial_signals &= ~SerialSignal_DTR;
2871
2872 spin_lock_irqsave(&info->irq_spinlock,flags);
2873 usc_set_serial_signals(info);
2874 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2875
2876 return 0;
2877}
2878
2879/* mgsl_break() Set or clear transmit break condition
2880 *
2881 * Arguments: tty pointer to tty instance data
2882 * break_state -1=set break condition, 0=clear
2883 * Return Value: error code
2884 */
2885static int mgsl_break(struct tty_struct *tty, int break_state)
2886{
2887 struct mgsl_struct * info = tty->driver_data;
2888 unsigned long flags;
2889
2890 if (debug_level >= DEBUG_LEVEL_INFO)
2891 printk("%s(%d):mgsl_break(%s,%d)\n",
2892 __FILE__,__LINE__, info->device_name, break_state);
2893
2894 if (mgsl_paranoia_check(info, tty->name, "mgsl_break"))
2895 return -EINVAL;
2896
2897 spin_lock_irqsave(&info->irq_spinlock,flags);
2898 if (break_state == -1)
2899 usc_OutReg(info,IOCR,(u16)(usc_InReg(info,IOCR) | BIT7));
2900 else
2901 usc_OutReg(info,IOCR,(u16)(usc_InReg(info,IOCR) & ~BIT7));
2902 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2903 return 0;
2904
2905} /* end of mgsl_break() */
2906
2907/*
2908 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
2909 * Return: write counters to the user passed counter struct
2910 * NB: both 1->0 and 0->1 transitions are counted except for
2911 * RI where only 0->1 is counted.
2912 */
2913static int msgl_get_icount(struct tty_struct *tty,
2914 struct serial_icounter_struct *icount)
2915
2916{
2917 struct mgsl_struct * info = tty->driver_data;
2918 struct mgsl_icount cnow; /* kernel counter temps */
2919 unsigned long flags;
2920
2921 spin_lock_irqsave(&info->irq_spinlock,flags);
2922 cnow = info->icount;
2923 spin_unlock_irqrestore(&info->irq_spinlock,flags);
2924
2925 icount->cts = cnow.cts;
2926 icount->dsr = cnow.dsr;
2927 icount->rng = cnow.rng;
2928 icount->dcd = cnow.dcd;
2929 icount->rx = cnow.rx;
2930 icount->tx = cnow.tx;
2931 icount->frame = cnow.frame;
2932 icount->overrun = cnow.overrun;
2933 icount->parity = cnow.parity;
2934 icount->brk = cnow.brk;
2935 icount->buf_overrun = cnow.buf_overrun;
2936 return 0;
2937}
2938
2939/* mgsl_ioctl() Service an IOCTL request
2940 *
2941 * Arguments:
2942 *
2943 * tty pointer to tty instance data
2944 * cmd IOCTL command code
2945 * arg command argument/context
2946 *
2947 * Return Value: 0 if success, otherwise error code
2948 */
2949static int mgsl_ioctl(struct tty_struct *tty,
2950 unsigned int cmd, unsigned long arg)
2951{
2952 struct mgsl_struct * info = tty->driver_data;
2953
2954 if (debug_level >= DEBUG_LEVEL_INFO)
2955 printk("%s(%d):mgsl_ioctl %s cmd=%08X\n", __FILE__,__LINE__,
2956 info->device_name, cmd );
2957
2958 if (mgsl_paranoia_check(info, tty->name, "mgsl_ioctl"))
2959 return -ENODEV;
2960
2961 if (cmd != TIOCMIWAIT) {
2962 if (tty_io_error(tty))
2963 return -EIO;
2964 }
2965
2966 return mgsl_ioctl_common(info, cmd, arg);
2967}
2968
2969static int mgsl_ioctl_common(struct mgsl_struct *info, unsigned int cmd, unsigned long arg)
2970{
2971 void __user *argp = (void __user *)arg;
2972
2973 switch (cmd) {
2974 case MGSL_IOCGPARAMS:
2975 return mgsl_get_params(info, argp);
2976 case MGSL_IOCSPARAMS:
2977 return mgsl_set_params(info, argp);
2978 case MGSL_IOCGTXIDLE:
2979 return mgsl_get_txidle(info, argp);
2980 case MGSL_IOCSTXIDLE:
2981 return mgsl_set_txidle(info,(int)arg);
2982 case MGSL_IOCTXENABLE:
2983 return mgsl_txenable(info,(int)arg);
2984 case MGSL_IOCRXENABLE:
2985 return mgsl_rxenable(info,(int)arg);
2986 case MGSL_IOCTXABORT:
2987 return mgsl_txabort(info);
2988 case MGSL_IOCGSTATS:
2989 return mgsl_get_stats(info, argp);
2990 case MGSL_IOCWAITEVENT:
2991 return mgsl_wait_event(info, argp);
2992 case MGSL_IOCLOOPTXDONE:
2993 return mgsl_loopmode_send_done(info);
2994 /* Wait for modem input (DCD,RI,DSR,CTS) change
2995 * as specified by mask in arg (TIOCM_RNG/DSR/CD/CTS)
2996 */
2997 case TIOCMIWAIT:
2998 return modem_input_wait(info,(int)arg);
2999
3000 default:
3001 return -ENOIOCTLCMD;
3002 }
3003 return 0;
3004}
3005
3006/* mgsl_set_termios()
3007 *
3008 * Set new termios settings
3009 *
3010 * Arguments:
3011 *
3012 * tty pointer to tty structure
3013 * termios pointer to buffer to hold returned old termios
3014 *
3015 * Return Value: None
3016 */
3017static void mgsl_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
3018{
3019 struct mgsl_struct *info = tty->driver_data;
3020 unsigned long flags;
3021
3022 if (debug_level >= DEBUG_LEVEL_INFO)
3023 printk("%s(%d):mgsl_set_termios %s\n", __FILE__,__LINE__,
3024 tty->driver->name );
3025
3026 mgsl_change_params(info);
3027
3028 /* Handle transition to B0 status */
3029 if ((old_termios->c_cflag & CBAUD) && !C_BAUD(tty)) {
3030 info->serial_signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
3031 spin_lock_irqsave(&info->irq_spinlock,flags);
3032 usc_set_serial_signals(info);
3033 spin_unlock_irqrestore(&info->irq_spinlock,flags);
3034 }
3035
3036 /* Handle transition away from B0 status */
3037 if (!(old_termios->c_cflag & CBAUD) && C_BAUD(tty)) {
3038 info->serial_signals |= SerialSignal_DTR;
3039 if (!C_CRTSCTS(tty) || !tty_throttled(tty))
3040 info->serial_signals |= SerialSignal_RTS;
3041 spin_lock_irqsave(&info->irq_spinlock,flags);
3042 usc_set_serial_signals(info);
3043 spin_unlock_irqrestore(&info->irq_spinlock,flags);
3044 }
3045
3046 /* Handle turning off CRTSCTS */
3047 if (old_termios->c_cflag & CRTSCTS && !C_CRTSCTS(tty)) {
3048 tty->hw_stopped = 0;
3049 mgsl_start(tty);
3050 }
3051
3052} /* end of mgsl_set_termios() */
3053
3054/* mgsl_close()
3055 *
3056 * Called when port is closed. Wait for remaining data to be
3057 * sent. Disable port and free resources.
3058 *
3059 * Arguments:
3060 *
3061 * tty pointer to open tty structure
3062 * filp pointer to open file object
3063 *
3064 * Return Value: None
3065 */
3066static void mgsl_close(struct tty_struct *tty, struct file * filp)
3067{
3068 struct mgsl_struct * info = tty->driver_data;
3069
3070 if (mgsl_paranoia_check(info, tty->name, "mgsl_close"))
3071 return;
3072
3073 if (debug_level >= DEBUG_LEVEL_INFO)
3074 printk("%s(%d):mgsl_close(%s) entry, count=%d\n",
3075 __FILE__,__LINE__, info->device_name, info->port.count);
3076
3077 if (tty_port_close_start(&info->port, tty, filp) == 0)
3078 goto cleanup;
3079
3080 mutex_lock(&info->port.mutex);
3081 if (tty_port_initialized(&info->port))
3082 mgsl_wait_until_sent(tty, info->timeout);
3083 mgsl_flush_buffer(tty);
3084 tty_ldisc_flush(tty);
3085 shutdown(info);
3086 mutex_unlock(&info->port.mutex);
3087
3088 tty_port_close_end(&info->port, tty);
3089 info->port.tty = NULL;
3090cleanup:
3091 if (debug_level >= DEBUG_LEVEL_INFO)
3092 printk("%s(%d):mgsl_close(%s) exit, count=%d\n", __FILE__,__LINE__,
3093 tty->driver->name, info->port.count);
3094
3095} /* end of mgsl_close() */
3096
3097/* mgsl_wait_until_sent()
3098 *
3099 * Wait until the transmitter is empty.
3100 *
3101 * Arguments:
3102 *
3103 * tty pointer to tty info structure
3104 * timeout time to wait for send completion
3105 *
3106 * Return Value: None
3107 */
3108static void mgsl_wait_until_sent(struct tty_struct *tty, int timeout)
3109{
3110 struct mgsl_struct * info = tty->driver_data;
3111 unsigned long orig_jiffies, char_time;
3112
3113 if (!info )
3114 return;
3115
3116 if (debug_level >= DEBUG_LEVEL_INFO)
3117 printk("%s(%d):mgsl_wait_until_sent(%s) entry\n",
3118 __FILE__,__LINE__, info->device_name );
3119
3120 if (mgsl_paranoia_check(info, tty->name, "mgsl_wait_until_sent"))
3121 return;
3122
3123 if (!tty_port_initialized(&info->port))
3124 goto exit;
3125
3126 orig_jiffies = jiffies;
3127
3128 /* Set check interval to 1/5 of estimated time to
3129 * send a character, and make it at least 1. The check
3130 * interval should also be less than the timeout.
3131 * Note: use tight timings here to satisfy the NIST-PCTS.
3132 */
3133
3134 if ( info->params.data_rate ) {
3135 char_time = info->timeout/(32 * 5);
3136 if (!char_time)
3137 char_time++;
3138 } else
3139 char_time = 1;
3140
3141 if (timeout)
3142 char_time = min_t(unsigned long, char_time, timeout);
3143
3144 if ( info->params.mode == MGSL_MODE_HDLC ||
3145 info->params.mode == MGSL_MODE_RAW ) {
3146 while (info->tx_active) {
3147 msleep_interruptible(jiffies_to_msecs(char_time));
3148 if (signal_pending(current))
3149 break;
3150 if (timeout && time_after(jiffies, orig_jiffies + timeout))
3151 break;
3152 }
3153 } else {
3154 while (!(usc_InReg(info,TCSR) & TXSTATUS_ALL_SENT) &&
3155 info->tx_enabled) {
3156 msleep_interruptible(jiffies_to_msecs(char_time));
3157 if (signal_pending(current))
3158 break;
3159 if (timeout && time_after(jiffies, orig_jiffies + timeout))
3160 break;
3161 }
3162 }
3163
3164exit:
3165 if (debug_level >= DEBUG_LEVEL_INFO)
3166 printk("%s(%d):mgsl_wait_until_sent(%s) exit\n",
3167 __FILE__,__LINE__, info->device_name );
3168
3169} /* end of mgsl_wait_until_sent() */
3170
3171/* mgsl_hangup()
3172 *
3173 * Called by tty_hangup() when a hangup is signaled.
3174 * This is the same as to closing all open files for the port.
3175 *
3176 * Arguments: tty pointer to associated tty object
3177 * Return Value: None
3178 */
3179static void mgsl_hangup(struct tty_struct *tty)
3180{
3181 struct mgsl_struct * info = tty->driver_data;
3182
3183 if (debug_level >= DEBUG_LEVEL_INFO)
3184 printk("%s(%d):mgsl_hangup(%s)\n",
3185 __FILE__,__LINE__, info->device_name );
3186
3187 if (mgsl_paranoia_check(info, tty->name, "mgsl_hangup"))
3188 return;
3189
3190 mgsl_flush_buffer(tty);
3191 shutdown(info);
3192
3193 info->port.count = 0;
3194 tty_port_set_active(&info->port, 0);
3195 info->port.tty = NULL;
3196
3197 wake_up_interruptible(&info->port.open_wait);
3198
3199} /* end of mgsl_hangup() */
3200
3201/*
3202 * carrier_raised()
3203 *
3204 * Return true if carrier is raised
3205 */
3206
3207static int carrier_raised(struct tty_port *port)
3208{
3209 unsigned long flags;
3210 struct mgsl_struct *info = container_of(port, struct mgsl_struct, port);
3211
3212 spin_lock_irqsave(&info->irq_spinlock, flags);
3213 usc_get_serial_signals(info);
3214 spin_unlock_irqrestore(&info->irq_spinlock, flags);
3215 return (info->serial_signals & SerialSignal_DCD) ? 1 : 0;
3216}
3217
3218static void dtr_rts(struct tty_port *port, int on)
3219{
3220 struct mgsl_struct *info = container_of(port, struct mgsl_struct, port);
3221 unsigned long flags;
3222
3223 spin_lock_irqsave(&info->irq_spinlock,flags);
3224 if (on)
3225 info->serial_signals |= SerialSignal_RTS | SerialSignal_DTR;
3226 else
3227 info->serial_signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
3228 usc_set_serial_signals(info);
3229 spin_unlock_irqrestore(&info->irq_spinlock,flags);
3230}
3231
3232
3233/* block_til_ready()
3234 *
3235 * Block the current process until the specified port
3236 * is ready to be opened.
3237 *
3238 * Arguments:
3239 *
3240 * tty pointer to tty info structure
3241 * filp pointer to open file object
3242 * info pointer to device instance data
3243 *
3244 * Return Value: 0 if success, otherwise error code
3245 */
3246static int block_til_ready(struct tty_struct *tty, struct file * filp,
3247 struct mgsl_struct *info)
3248{
3249 DECLARE_WAITQUEUE(wait, current);
3250 int retval;
3251 bool do_clocal = false;
3252 unsigned long flags;
3253 int dcd;
3254 struct tty_port *port = &info->port;
3255
3256 if (debug_level >= DEBUG_LEVEL_INFO)
3257 printk("%s(%d):block_til_ready on %s\n",
3258 __FILE__,__LINE__, tty->driver->name );
3259
3260 if (filp->f_flags & O_NONBLOCK || tty_io_error(tty)) {
3261 /* nonblock mode is set or port is not enabled */
3262 tty_port_set_active(port, 1);
3263 return 0;
3264 }
3265
3266 if (C_CLOCAL(tty))
3267 do_clocal = true;
3268
3269 /* Wait for carrier detect and the line to become
3270 * free (i.e., not in use by the callout). While we are in
3271 * this loop, port->count is dropped by one, so that
3272 * mgsl_close() knows when to free things. We restore it upon
3273 * exit, either normal or abnormal.
3274 */
3275
3276 retval = 0;
3277 add_wait_queue(&port->open_wait, &wait);
3278
3279 if (debug_level >= DEBUG_LEVEL_INFO)
3280 printk("%s(%d):block_til_ready before block on %s count=%d\n",
3281 __FILE__,__LINE__, tty->driver->name, port->count );
3282
3283 spin_lock_irqsave(&info->irq_spinlock, flags);
3284 port->count--;
3285 spin_unlock_irqrestore(&info->irq_spinlock, flags);
3286 port->blocked_open++;
3287
3288 while (1) {
3289 if (C_BAUD(tty) && tty_port_initialized(port))
3290 tty_port_raise_dtr_rts(port);
3291
3292 set_current_state(TASK_INTERRUPTIBLE);
3293
3294 if (tty_hung_up_p(filp) || !tty_port_initialized(port)) {
3295 retval = (port->flags & ASYNC_HUP_NOTIFY) ?
3296 -EAGAIN : -ERESTARTSYS;
3297 break;
3298 }
3299
3300 dcd = tty_port_carrier_raised(&info->port);
3301 if (do_clocal || dcd)
3302 break;
3303
3304 if (signal_pending(current)) {
3305 retval = -ERESTARTSYS;
3306 break;
3307 }
3308
3309 if (debug_level >= DEBUG_LEVEL_INFO)
3310 printk("%s(%d):block_til_ready blocking on %s count=%d\n",
3311 __FILE__,__LINE__, tty->driver->name, port->count );
3312
3313 tty_unlock(tty);
3314 schedule();
3315 tty_lock(tty);
3316 }
3317
3318 set_current_state(TASK_RUNNING);
3319 remove_wait_queue(&port->open_wait, &wait);
3320
3321 /* FIXME: Racy on hangup during close wait */
3322 if (!tty_hung_up_p(filp))
3323 port->count++;
3324 port->blocked_open--;
3325
3326 if (debug_level >= DEBUG_LEVEL_INFO)
3327 printk("%s(%d):block_til_ready after blocking on %s count=%d\n",
3328 __FILE__,__LINE__, tty->driver->name, port->count );
3329
3330 if (!retval)
3331 tty_port_set_active(port, 1);
3332
3333 return retval;
3334
3335} /* end of block_til_ready() */
3336
3337static int mgsl_install(struct tty_driver *driver, struct tty_struct *tty)
3338{
3339 struct mgsl_struct *info;
3340 int line = tty->index;
3341
3342 /* verify range of specified line number */
3343 if (line >= mgsl_device_count) {
3344 printk("%s(%d):mgsl_open with invalid line #%d.\n",
3345 __FILE__, __LINE__, line);
3346 return -ENODEV;
3347 }
3348
3349 /* find the info structure for the specified line */
3350 info = mgsl_device_list;
3351 while (info && info->line != line)
3352 info = info->next_device;
3353 if (mgsl_paranoia_check(info, tty->name, "mgsl_open"))
3354 return -ENODEV;
3355 tty->driver_data = info;
3356
3357 return tty_port_install(&info->port, driver, tty);
3358}
3359
3360/* mgsl_open()
3361 *
3362 * Called when a port is opened. Init and enable port.
3363 * Perform serial-specific initialization for the tty structure.
3364 *
3365 * Arguments: tty pointer to tty info structure
3366 * filp associated file pointer
3367 *
3368 * Return Value: 0 if success, otherwise error code
3369 */
3370static int mgsl_open(struct tty_struct *tty, struct file * filp)
3371{
3372 struct mgsl_struct *info = tty->driver_data;
3373 unsigned long flags;
3374 int retval;
3375
3376 info->port.tty = tty;
3377
3378 if (debug_level >= DEBUG_LEVEL_INFO)
3379 printk("%s(%d):mgsl_open(%s), old ref count = %d\n",
3380 __FILE__,__LINE__,tty->driver->name, info->port.count);
3381
3382 info->port.low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
3383
3384 spin_lock_irqsave(&info->netlock, flags);
3385 if (info->netcount) {
3386 retval = -EBUSY;
3387 spin_unlock_irqrestore(&info->netlock, flags);
3388 goto cleanup;
3389 }
3390 info->port.count++;
3391 spin_unlock_irqrestore(&info->netlock, flags);
3392
3393 if (info->port.count == 1) {
3394 /* 1st open on this device, init hardware */
3395 retval = startup(info);
3396 if (retval < 0)
3397 goto cleanup;
3398 }
3399
3400 retval = block_til_ready(tty, filp, info);
3401 if (retval) {
3402 if (debug_level >= DEBUG_LEVEL_INFO)
3403 printk("%s(%d):block_til_ready(%s) returned %d\n",
3404 __FILE__,__LINE__, info->device_name, retval);
3405 goto cleanup;
3406 }
3407
3408 if (debug_level >= DEBUG_LEVEL_INFO)
3409 printk("%s(%d):mgsl_open(%s) success\n",
3410 __FILE__,__LINE__, info->device_name);
3411 retval = 0;
3412
3413cleanup:
3414 if (retval) {
3415 if (tty->count == 1)
3416 info->port.tty = NULL; /* tty layer will release tty struct */
3417 if(info->port.count)
3418 info->port.count--;
3419 }
3420
3421 return retval;
3422
3423} /* end of mgsl_open() */
3424
3425/*
3426 * /proc fs routines....
3427 */
3428
3429static inline void line_info(struct seq_file *m, struct mgsl_struct *info)
3430{
3431 char stat_buf[30];
3432 unsigned long flags;
3433
3434 seq_printf(m, "%s:PCI io:%04X irq:%d mem:%08X lcr:%08X",
3435 info->device_name, info->io_base, info->irq_level,
3436 info->phys_memory_base, info->phys_lcr_base);
3437
3438 /* output current serial signal states */
3439 spin_lock_irqsave(&info->irq_spinlock,flags);
3440 usc_get_serial_signals(info);
3441 spin_unlock_irqrestore(&info->irq_spinlock,flags);
3442
3443 stat_buf[0] = 0;
3444 stat_buf[1] = 0;
3445 if (info->serial_signals & SerialSignal_RTS)
3446 strcat(stat_buf, "|RTS");
3447 if (info->serial_signals & SerialSignal_CTS)
3448 strcat(stat_buf, "|CTS");
3449 if (info->serial_signals & SerialSignal_DTR)
3450 strcat(stat_buf, "|DTR");
3451 if (info->serial_signals & SerialSignal_DSR)
3452 strcat(stat_buf, "|DSR");
3453 if (info->serial_signals & SerialSignal_DCD)
3454 strcat(stat_buf, "|CD");
3455 if (info->serial_signals & SerialSignal_RI)
3456 strcat(stat_buf, "|RI");
3457
3458 if (info->params.mode == MGSL_MODE_HDLC ||
3459 info->params.mode == MGSL_MODE_RAW ) {
3460 seq_printf(m, " HDLC txok:%d rxok:%d",
3461 info->icount.txok, info->icount.rxok);
3462 if (info->icount.txunder)
3463 seq_printf(m, " txunder:%d", info->icount.txunder);
3464 if (info->icount.txabort)
3465 seq_printf(m, " txabort:%d", info->icount.txabort);
3466 if (info->icount.rxshort)
3467 seq_printf(m, " rxshort:%d", info->icount.rxshort);
3468 if (info->icount.rxlong)
3469 seq_printf(m, " rxlong:%d", info->icount.rxlong);
3470 if (info->icount.rxover)
3471 seq_printf(m, " rxover:%d", info->icount.rxover);
3472 if (info->icount.rxcrc)
3473 seq_printf(m, " rxcrc:%d", info->icount.rxcrc);
3474 } else {
3475 seq_printf(m, " ASYNC tx:%d rx:%d",
3476 info->icount.tx, info->icount.rx);
3477 if (info->icount.frame)
3478 seq_printf(m, " fe:%d", info->icount.frame);
3479 if (info->icount.parity)
3480 seq_printf(m, " pe:%d", info->icount.parity);
3481 if (info->icount.brk)
3482 seq_printf(m, " brk:%d", info->icount.brk);
3483 if (info->icount.overrun)
3484 seq_printf(m, " oe:%d", info->icount.overrun);
3485 }
3486
3487 /* Append serial signal status to end */
3488 seq_printf(m, " %s\n", stat_buf+1);
3489
3490 seq_printf(m, "txactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
3491 info->tx_active,info->bh_requested,info->bh_running,
3492 info->pending_bh);
3493
3494 spin_lock_irqsave(&info->irq_spinlock,flags);
3495 {
3496 u16 Tcsr = usc_InReg( info, TCSR );
3497 u16 Tdmr = usc_InDmaReg( info, TDMR );
3498 u16 Ticr = usc_InReg( info, TICR );
3499 u16 Rscr = usc_InReg( info, RCSR );
3500 u16 Rdmr = usc_InDmaReg( info, RDMR );
3501 u16 Ricr = usc_InReg( info, RICR );
3502 u16 Icr = usc_InReg( info, ICR );
3503 u16 Dccr = usc_InReg( info, DCCR );
3504 u16 Tmr = usc_InReg( info, TMR );
3505 u16 Tccr = usc_InReg( info, TCCR );
3506 u16 Ccar = inw( info->io_base + CCAR );
3507 seq_printf(m, "tcsr=%04X tdmr=%04X ticr=%04X rcsr=%04X rdmr=%04X\n"
3508 "ricr=%04X icr =%04X dccr=%04X tmr=%04X tccr=%04X ccar=%04X\n",
3509 Tcsr,Tdmr,Ticr,Rscr,Rdmr,Ricr,Icr,Dccr,Tmr,Tccr,Ccar );
3510 }
3511 spin_unlock_irqrestore(&info->irq_spinlock,flags);
3512}
3513
3514/* Called to print information about devices */
3515static int mgsl_proc_show(struct seq_file *m, void *v)
3516{
3517 struct mgsl_struct *info;
3518
3519 seq_printf(m, "synclink driver:%s\n", driver_version);
3520
3521 info = mgsl_device_list;
3522 while( info ) {
3523 line_info(m, info);
3524 info = info->next_device;
3525 }
3526 return 0;
3527}
3528
3529/* mgsl_allocate_dma_buffers()
3530 *
3531 * Allocate and format DMA buffers (ISA adapter)
3532 * or format shared memory buffers (PCI adapter).
3533 *
3534 * Arguments: info pointer to device instance data
3535 * Return Value: 0 if success, otherwise error
3536 */
3537static int mgsl_allocate_dma_buffers(struct mgsl_struct *info)
3538{
3539 unsigned short BuffersPerFrame;
3540
3541 info->last_mem_alloc = 0;
3542
3543 /* Calculate the number of DMA buffers necessary to hold the */
3544 /* largest allowable frame size. Note: If the max frame size is */
3545 /* not an even multiple of the DMA buffer size then we need to */
3546 /* round the buffer count per frame up one. */
3547
3548 BuffersPerFrame = (unsigned short)(info->max_frame_size/DMABUFFERSIZE);
3549 if ( info->max_frame_size % DMABUFFERSIZE )
3550 BuffersPerFrame++;
3551
3552 /*
3553 * The PCI adapter has 256KBytes of shared memory to use. This is 64
3554 * PAGE_SIZE buffers.
3555 *
3556 * The first page is used for padding at this time so the buffer list
3557 * does not begin at offset 0 of the PCI adapter's shared memory.
3558 *
3559 * The 2nd page is used for the buffer list. A 4K buffer list can hold
3560 * 128 DMA_BUFFER structures at 32 bytes each.
3561 *
3562 * This leaves 62 4K pages.
3563 *
3564 * The next N pages are used for transmit frame(s). We reserve enough
3565 * 4K page blocks to hold the required number of transmit dma buffers
3566 * (num_tx_dma_buffers), each of MaxFrameSize size.
3567 *
3568 * Of the remaining pages (62-N), determine how many can be used to
3569 * receive full MaxFrameSize inbound frames
3570 */
3571 info->tx_buffer_count = info->num_tx_dma_buffers * BuffersPerFrame;
3572 info->rx_buffer_count = 62 - info->tx_buffer_count;
3573
3574 if ( debug_level >= DEBUG_LEVEL_INFO )
3575 printk("%s(%d):Allocating %d TX and %d RX DMA buffers.\n",
3576 __FILE__,__LINE__, info->tx_buffer_count,info->rx_buffer_count);
3577
3578 if ( mgsl_alloc_buffer_list_memory( info ) < 0 ||
3579 mgsl_alloc_frame_memory(info, info->rx_buffer_list, info->rx_buffer_count) < 0 ||
3580 mgsl_alloc_frame_memory(info, info->tx_buffer_list, info->tx_buffer_count) < 0 ||
3581 mgsl_alloc_intermediate_rxbuffer_memory(info) < 0 ||
3582 mgsl_alloc_intermediate_txbuffer_memory(info) < 0 ) {
3583 printk("%s(%d):Can't allocate DMA buffer memory\n",__FILE__,__LINE__);
3584 return -ENOMEM;
3585 }
3586
3587 mgsl_reset_rx_dma_buffers( info );
3588 mgsl_reset_tx_dma_buffers( info );
3589
3590 return 0;
3591
3592} /* end of mgsl_allocate_dma_buffers() */
3593
3594/*
3595 * mgsl_alloc_buffer_list_memory()
3596 *
3597 * Allocate a common DMA buffer for use as the
3598 * receive and transmit buffer lists.
3599 *
3600 * A buffer list is a set of buffer entries where each entry contains
3601 * a pointer to an actual buffer and a pointer to the next buffer entry
3602 * (plus some other info about the buffer).
3603 *
3604 * The buffer entries for a list are built to form a circular list so
3605 * that when the entire list has been traversed you start back at the
3606 * beginning.
3607 *
3608 * This function allocates memory for just the buffer entries.
3609 * The links (pointer to next entry) are filled in with the physical
3610 * address of the next entry so the adapter can navigate the list
3611 * using bus master DMA. The pointers to the actual buffers are filled
3612 * out later when the actual buffers are allocated.
3613 *
3614 * Arguments: info pointer to device instance data
3615 * Return Value: 0 if success, otherwise error
3616 */
3617static int mgsl_alloc_buffer_list_memory( struct mgsl_struct *info )
3618{
3619 unsigned int i;
3620
3621 /* PCI adapter uses shared memory. */
3622 info->buffer_list = info->memory_base + info->last_mem_alloc;
3623 info->buffer_list_phys = info->last_mem_alloc;
3624 info->last_mem_alloc += BUFFERLISTSIZE;
3625
3626 /* We got the memory for the buffer entry lists. */
3627 /* Initialize the memory block to all zeros. */
3628 memset( info->buffer_list, 0, BUFFERLISTSIZE );
3629
3630 /* Save virtual address pointers to the receive and */
3631 /* transmit buffer lists. (Receive 1st). These pointers will */
3632 /* be used by the processor to access the lists. */
3633 info->rx_buffer_list = (DMABUFFERENTRY *)info->buffer_list;
3634 info->tx_buffer_list = (DMABUFFERENTRY *)info->buffer_list;
3635 info->tx_buffer_list += info->rx_buffer_count;
3636
3637 /*
3638 * Build the links for the buffer entry lists such that
3639 * two circular lists are built. (Transmit and Receive).
3640 *
3641 * Note: the links are physical addresses
3642 * which are read by the adapter to determine the next
3643 * buffer entry to use.
3644 */
3645
3646 for ( i = 0; i < info->rx_buffer_count; i++ ) {
3647 /* calculate and store physical address of this buffer entry */
3648 info->rx_buffer_list[i].phys_entry =
3649 info->buffer_list_phys + (i * sizeof(DMABUFFERENTRY));
3650
3651 /* calculate and store physical address of */
3652 /* next entry in cirular list of entries */
3653
3654 info->rx_buffer_list[i].link = info->buffer_list_phys;
3655
3656 if ( i < info->rx_buffer_count - 1 )
3657 info->rx_buffer_list[i].link += (i + 1) * sizeof(DMABUFFERENTRY);
3658 }
3659
3660 for ( i = 0; i < info->tx_buffer_count; i++ ) {
3661 /* calculate and store physical address of this buffer entry */
3662 info->tx_buffer_list[i].phys_entry = info->buffer_list_phys +
3663 ((info->rx_buffer_count + i) * sizeof(DMABUFFERENTRY));
3664
3665 /* calculate and store physical address of */
3666 /* next entry in cirular list of entries */
3667
3668 info->tx_buffer_list[i].link = info->buffer_list_phys +
3669 info->rx_buffer_count * sizeof(DMABUFFERENTRY);
3670
3671 if ( i < info->tx_buffer_count - 1 )
3672 info->tx_buffer_list[i].link += (i + 1) * sizeof(DMABUFFERENTRY);
3673 }
3674
3675 return 0;
3676
3677} /* end of mgsl_alloc_buffer_list_memory() */
3678
3679/* Free DMA buffers allocated for use as the
3680 * receive and transmit buffer lists.
3681 * Warning:
3682 *
3683 * The data transfer buffers associated with the buffer list
3684 * MUST be freed before freeing the buffer list itself because
3685 * the buffer list contains the information necessary to free
3686 * the individual buffers!
3687 */
3688static void mgsl_free_buffer_list_memory( struct mgsl_struct *info )
3689{
3690 info->buffer_list = NULL;
3691 info->rx_buffer_list = NULL;
3692 info->tx_buffer_list = NULL;
3693
3694} /* end of mgsl_free_buffer_list_memory() */
3695
3696/*
3697 * mgsl_alloc_frame_memory()
3698 *
3699 * Allocate the frame DMA buffers used by the specified buffer list.
3700 * Each DMA buffer will be one memory page in size. This is necessary
3701 * because memory can fragment enough that it may be impossible
3702 * contiguous pages.
3703 *
3704 * Arguments:
3705 *
3706 * info pointer to device instance data
3707 * BufferList pointer to list of buffer entries
3708 * Buffercount count of buffer entries in buffer list
3709 *
3710 * Return Value: 0 if success, otherwise -ENOMEM
3711 */
3712static int mgsl_alloc_frame_memory(struct mgsl_struct *info,DMABUFFERENTRY *BufferList,int Buffercount)
3713{
3714 int i;
3715
3716 /* Allocate page sized buffers for the receive buffer list */
3717
3718 for ( i = 0; i < Buffercount; i++ ) {
3719 BufferList[i].virt_addr = info->memory_base + info->last_mem_alloc;
3720 BufferList[i].phys_addr = info->last_mem_alloc;
3721 info->last_mem_alloc += DMABUFFERSIZE;
3722 }
3723
3724 return 0;
3725
3726} /* end of mgsl_alloc_frame_memory() */
3727
3728/*
3729 * mgsl_free_frame_memory()
3730 *
3731 * Free the buffers associated with
3732 * each buffer entry of a buffer list.
3733 *
3734 * Arguments:
3735 *
3736 * info pointer to device instance data
3737 * BufferList pointer to list of buffer entries
3738 * Buffercount count of buffer entries in buffer list
3739 *
3740 * Return Value: None
3741 */
3742static void mgsl_free_frame_memory(struct mgsl_struct *info, DMABUFFERENTRY *BufferList, int Buffercount)
3743{
3744 int i;
3745
3746 if ( BufferList ) {
3747 for ( i = 0 ; i < Buffercount ; i++ ) {
3748 if ( BufferList[i].virt_addr ) {
3749 BufferList[i].virt_addr = NULL;
3750 }
3751 }
3752 }
3753
3754} /* end of mgsl_free_frame_memory() */
3755
3756/* mgsl_free_dma_buffers()
3757 *
3758 * Free DMA buffers
3759 *
3760 * Arguments: info pointer to device instance data
3761 * Return Value: None
3762 */
3763static void mgsl_free_dma_buffers( struct mgsl_struct *info )
3764{
3765 mgsl_free_frame_memory( info, info->rx_buffer_list, info->rx_buffer_count );
3766 mgsl_free_frame_memory( info, info->tx_buffer_list, info->tx_buffer_count );
3767 mgsl_free_buffer_list_memory( info );
3768
3769} /* end of mgsl_free_dma_buffers() */
3770
3771
3772/*
3773 * mgsl_alloc_intermediate_rxbuffer_memory()
3774 *
3775 * Allocate a buffer large enough to hold max_frame_size. This buffer
3776 * is used to pass an assembled frame to the line discipline.
3777 *
3778 * Arguments:
3779 *
3780 * info pointer to device instance data
3781 *
3782 * Return Value: 0 if success, otherwise -ENOMEM
3783 */
3784static int mgsl_alloc_intermediate_rxbuffer_memory(struct mgsl_struct *info)
3785{
3786 info->intermediate_rxbuffer = kmalloc(info->max_frame_size, GFP_KERNEL | GFP_DMA);
3787 if ( info->intermediate_rxbuffer == NULL )
3788 return -ENOMEM;
3789 /* unused flag buffer to satisfy receive_buf calling interface */
3790 info->flag_buf = kzalloc(info->max_frame_size, GFP_KERNEL);
3791 if (!info->flag_buf) {
3792 kfree(info->intermediate_rxbuffer);
3793 info->intermediate_rxbuffer = NULL;
3794 return -ENOMEM;
3795 }
3796 return 0;
3797
3798} /* end of mgsl_alloc_intermediate_rxbuffer_memory() */
3799
3800/*
3801 * mgsl_free_intermediate_rxbuffer_memory()
3802 *
3803 *
3804 * Arguments:
3805 *
3806 * info pointer to device instance data
3807 *
3808 * Return Value: None
3809 */
3810static void mgsl_free_intermediate_rxbuffer_memory(struct mgsl_struct *info)
3811{
3812 kfree(info->intermediate_rxbuffer);
3813 info->intermediate_rxbuffer = NULL;
3814 kfree(info->flag_buf);
3815 info->flag_buf = NULL;
3816
3817} /* end of mgsl_free_intermediate_rxbuffer_memory() */
3818
3819/*
3820 * mgsl_alloc_intermediate_txbuffer_memory()
3821 *
3822 * Allocate intermdiate transmit buffer(s) large enough to hold max_frame_size.
3823 * This buffer is used to load transmit frames into the adapter's dma transfer
3824 * buffers when there is sufficient space.
3825 *
3826 * Arguments:
3827 *
3828 * info pointer to device instance data
3829 *
3830 * Return Value: 0 if success, otherwise -ENOMEM
3831 */
3832static int mgsl_alloc_intermediate_txbuffer_memory(struct mgsl_struct *info)
3833{
3834 int i;
3835
3836 if ( debug_level >= DEBUG_LEVEL_INFO )
3837 printk("%s %s(%d) allocating %d tx holding buffers\n",
3838 info->device_name, __FILE__,__LINE__,info->num_tx_holding_buffers);
3839
3840 memset(info->tx_holding_buffers,0,sizeof(info->tx_holding_buffers));
3841
3842 for ( i=0; i<info->num_tx_holding_buffers; ++i) {
3843 info->tx_holding_buffers[i].buffer =
3844 kmalloc(info->max_frame_size, GFP_KERNEL);
3845 if (info->tx_holding_buffers[i].buffer == NULL) {
3846 for (--i; i >= 0; i--) {
3847 kfree(info->tx_holding_buffers[i].buffer);
3848 info->tx_holding_buffers[i].buffer = NULL;
3849 }
3850 return -ENOMEM;
3851 }
3852 }
3853
3854 return 0;
3855
3856} /* end of mgsl_alloc_intermediate_txbuffer_memory() */
3857
3858/*
3859 * mgsl_free_intermediate_txbuffer_memory()
3860 *
3861 *
3862 * Arguments:
3863 *
3864 * info pointer to device instance data
3865 *
3866 * Return Value: None
3867 */
3868static void mgsl_free_intermediate_txbuffer_memory(struct mgsl_struct *info)
3869{
3870 int i;
3871
3872 for ( i=0; i<info->num_tx_holding_buffers; ++i ) {
3873 kfree(info->tx_holding_buffers[i].buffer);
3874 info->tx_holding_buffers[i].buffer = NULL;
3875 }
3876
3877 info->get_tx_holding_index = 0;
3878 info->put_tx_holding_index = 0;
3879 info->tx_holding_count = 0;
3880
3881} /* end of mgsl_free_intermediate_txbuffer_memory() */
3882
3883
3884/*
3885 * load_next_tx_holding_buffer()
3886 *
3887 * attempts to load the next buffered tx request into the
3888 * tx dma buffers
3889 *
3890 * Arguments:
3891 *
3892 * info pointer to device instance data
3893 *
3894 * Return Value: true if next buffered tx request loaded
3895 * into adapter's tx dma buffer,
3896 * false otherwise
3897 */
3898static bool load_next_tx_holding_buffer(struct mgsl_struct *info)
3899{
3900 bool ret = false;
3901
3902 if ( info->tx_holding_count ) {
3903 /* determine if we have enough tx dma buffers
3904 * to accommodate the next tx frame
3905 */
3906 struct tx_holding_buffer *ptx =
3907 &info->tx_holding_buffers[info->get_tx_holding_index];
3908 int num_free = num_free_tx_dma_buffers(info);
3909 int num_needed = ptx->buffer_size / DMABUFFERSIZE;
3910 if ( ptx->buffer_size % DMABUFFERSIZE )
3911 ++num_needed;
3912
3913 if (num_needed <= num_free) {
3914 info->xmit_cnt = ptx->buffer_size;
3915 mgsl_load_tx_dma_buffer(info,ptx->buffer,ptx->buffer_size);
3916
3917 --info->tx_holding_count;
3918 if ( ++info->get_tx_holding_index >= info->num_tx_holding_buffers)
3919 info->get_tx_holding_index=0;
3920
3921 /* restart transmit timer */
3922 mod_timer(&info->tx_timer, jiffies + msecs_to_jiffies(5000));
3923
3924 ret = true;
3925 }
3926 }
3927
3928 return ret;
3929}
3930
3931/*
3932 * save_tx_buffer_request()
3933 *
3934 * attempt to store transmit frame request for later transmission
3935 *
3936 * Arguments:
3937 *
3938 * info pointer to device instance data
3939 * Buffer pointer to buffer containing frame to load
3940 * BufferSize size in bytes of frame in Buffer
3941 *
3942 * Return Value: 1 if able to store, 0 otherwise
3943 */
3944static int save_tx_buffer_request(struct mgsl_struct *info,const char *Buffer, unsigned int BufferSize)
3945{
3946 struct tx_holding_buffer *ptx;
3947
3948 if ( info->tx_holding_count >= info->num_tx_holding_buffers ) {
3949 return 0; /* all buffers in use */
3950 }
3951
3952 ptx = &info->tx_holding_buffers[info->put_tx_holding_index];
3953 ptx->buffer_size = BufferSize;
3954 memcpy( ptx->buffer, Buffer, BufferSize);
3955
3956 ++info->tx_holding_count;
3957 if ( ++info->put_tx_holding_index >= info->num_tx_holding_buffers)
3958 info->put_tx_holding_index=0;
3959
3960 return 1;
3961}
3962
3963static int mgsl_claim_resources(struct mgsl_struct *info)
3964{
3965 if (request_region(info->io_base,info->io_addr_size,"synclink") == NULL) {
3966 printk( "%s(%d):I/O address conflict on device %s Addr=%08X\n",
3967 __FILE__,__LINE__,info->device_name, info->io_base);
3968 return -ENODEV;
3969 }
3970 info->io_addr_requested = true;
3971
3972 if ( request_irq(info->irq_level,mgsl_interrupt,info->irq_flags,
3973 info->device_name, info ) < 0 ) {
3974 printk( "%s(%d):Can't request interrupt on device %s IRQ=%d\n",
3975 __FILE__,__LINE__,info->device_name, info->irq_level );
3976 goto errout;
3977 }
3978 info->irq_requested = true;
3979
3980 if (request_mem_region(info->phys_memory_base,0x40000,"synclink") == NULL) {
3981 printk( "%s(%d):mem addr conflict device %s Addr=%08X\n",
3982 __FILE__,__LINE__,info->device_name, info->phys_memory_base);
3983 goto errout;
3984 }
3985 info->shared_mem_requested = true;
3986 if (request_mem_region(info->phys_lcr_base + info->lcr_offset,128,"synclink") == NULL) {
3987 printk( "%s(%d):lcr mem addr conflict device %s Addr=%08X\n",
3988 __FILE__,__LINE__,info->device_name, info->phys_lcr_base + info->lcr_offset);
3989 goto errout;
3990 }
3991 info->lcr_mem_requested = true;
3992
3993 info->memory_base = ioremap(info->phys_memory_base, 0x40000);
3994 if (!info->memory_base) {
3995 printk( "%s(%d):Can't map shared memory on device %s MemAddr=%08X\n",
3996 __FILE__,__LINE__,info->device_name, info->phys_memory_base );
3997 goto errout;
3998 }
3999
4000 if ( !mgsl_memory_test(info) ) {
4001 printk( "%s(%d):Failed shared memory test %s MemAddr=%08X\n",
4002 __FILE__,__LINE__,info->device_name, info->phys_memory_base );
4003 goto errout;
4004 }
4005
4006 info->lcr_base = ioremap(info->phys_lcr_base, PAGE_SIZE);
4007 if (!info->lcr_base) {
4008 printk( "%s(%d):Can't map LCR memory on device %s MemAddr=%08X\n",
4009 __FILE__,__LINE__,info->device_name, info->phys_lcr_base );
4010 goto errout;
4011 }
4012 info->lcr_base += info->lcr_offset;
4013
4014 if ( mgsl_allocate_dma_buffers(info) < 0 ) {
4015 printk( "%s(%d):Can't allocate DMA buffers on device %s DMA=%d\n",
4016 __FILE__,__LINE__,info->device_name, info->dma_level );
4017 goto errout;
4018 }
4019
4020 return 0;
4021errout:
4022 mgsl_release_resources(info);
4023 return -ENODEV;
4024
4025} /* end of mgsl_claim_resources() */
4026
4027static void mgsl_release_resources(struct mgsl_struct *info)
4028{
4029 if ( debug_level >= DEBUG_LEVEL_INFO )
4030 printk( "%s(%d):mgsl_release_resources(%s) entry\n",
4031 __FILE__,__LINE__,info->device_name );
4032
4033 if ( info->irq_requested ) {
4034 free_irq(info->irq_level, info);
4035 info->irq_requested = false;
4036 }
4037 if ( info->dma_requested ) {
4038 disable_dma(info->dma_level);
4039 free_dma(info->dma_level);
4040 info->dma_requested = false;
4041 }
4042 mgsl_free_dma_buffers(info);
4043 mgsl_free_intermediate_rxbuffer_memory(info);
4044 mgsl_free_intermediate_txbuffer_memory(info);
4045
4046 if ( info->io_addr_requested ) {
4047 release_region(info->io_base,info->io_addr_size);
4048 info->io_addr_requested = false;
4049 }
4050 if ( info->shared_mem_requested ) {
4051 release_mem_region(info->phys_memory_base,0x40000);
4052 info->shared_mem_requested = false;
4053 }
4054 if ( info->lcr_mem_requested ) {
4055 release_mem_region(info->phys_lcr_base + info->lcr_offset,128);
4056 info->lcr_mem_requested = false;
4057 }
4058 if (info->memory_base){
4059 iounmap(info->memory_base);
4060 info->memory_base = NULL;
4061 }
4062 if (info->lcr_base){
4063 iounmap(info->lcr_base - info->lcr_offset);
4064 info->lcr_base = NULL;
4065 }
4066
4067 if ( debug_level >= DEBUG_LEVEL_INFO )
4068 printk( "%s(%d):mgsl_release_resources(%s) exit\n",
4069 __FILE__,__LINE__,info->device_name );
4070
4071} /* end of mgsl_release_resources() */
4072
4073/* mgsl_add_device()
4074 *
4075 * Add the specified device instance data structure to the
4076 * global linked list of devices and increment the device count.
4077 *
4078 * Arguments: info pointer to device instance data
4079 * Return Value: None
4080 */
4081static void mgsl_add_device( struct mgsl_struct *info )
4082{
4083 info->next_device = NULL;
4084 info->line = mgsl_device_count;
4085 sprintf(info->device_name,"ttySL%d",info->line);
4086
4087 if (info->line < MAX_TOTAL_DEVICES) {
4088 if (maxframe[info->line])
4089 info->max_frame_size = maxframe[info->line];
4090
4091 if (txdmabufs[info->line]) {
4092 info->num_tx_dma_buffers = txdmabufs[info->line];
4093 if (info->num_tx_dma_buffers < 1)
4094 info->num_tx_dma_buffers = 1;
4095 }
4096
4097 if (txholdbufs[info->line]) {
4098 info->num_tx_holding_buffers = txholdbufs[info->line];
4099 if (info->num_tx_holding_buffers < 1)
4100 info->num_tx_holding_buffers = 1;
4101 else if (info->num_tx_holding_buffers > MAX_TX_HOLDING_BUFFERS)
4102 info->num_tx_holding_buffers = MAX_TX_HOLDING_BUFFERS;
4103 }
4104 }
4105
4106 mgsl_device_count++;
4107
4108 if ( !mgsl_device_list )
4109 mgsl_device_list = info;
4110 else {
4111 struct mgsl_struct *current_dev = mgsl_device_list;
4112 while( current_dev->next_device )
4113 current_dev = current_dev->next_device;
4114 current_dev->next_device = info;
4115 }
4116
4117 if ( info->max_frame_size < 4096 )
4118 info->max_frame_size = 4096;
4119 else if ( info->max_frame_size > 65535 )
4120 info->max_frame_size = 65535;
4121
4122 printk( "SyncLink PCI v%d %s: IO=%04X IRQ=%d Mem=%08X,%08X MaxFrameSize=%u\n",
4123 info->hw_version + 1, info->device_name, info->io_base, info->irq_level,
4124 info->phys_memory_base, info->phys_lcr_base,
4125 info->max_frame_size );
4126
4127#if SYNCLINK_GENERIC_HDLC
4128 hdlcdev_init(info);
4129#endif
4130
4131} /* end of mgsl_add_device() */
4132
4133static const struct tty_port_operations mgsl_port_ops = {
4134 .carrier_raised = carrier_raised,
4135 .dtr_rts = dtr_rts,
4136};
4137
4138
4139/* mgsl_allocate_device()
4140 *
4141 * Allocate and initialize a device instance structure
4142 *
4143 * Arguments: none
4144 * Return Value: pointer to mgsl_struct if success, otherwise NULL
4145 */
4146static struct mgsl_struct* mgsl_allocate_device(void)
4147{
4148 struct mgsl_struct *info;
4149
4150 info = kzalloc(sizeof(struct mgsl_struct),
4151 GFP_KERNEL);
4152
4153 if (!info) {
4154 printk("Error can't allocate device instance data\n");
4155 } else {
4156 tty_port_init(&info->port);
4157 info->port.ops = &mgsl_port_ops;
4158 info->magic = MGSL_MAGIC;
4159 INIT_WORK(&info->task, mgsl_bh_handler);
4160 info->max_frame_size = 4096;
4161 info->port.close_delay = 5*HZ/10;
4162 info->port.closing_wait = 30*HZ;
4163 init_waitqueue_head(&info->status_event_wait_q);
4164 init_waitqueue_head(&info->event_wait_q);
4165 spin_lock_init(&info->irq_spinlock);
4166 spin_lock_init(&info->netlock);
4167 memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS));
4168 info->idle_mode = HDLC_TXIDLE_FLAGS;
4169 info->num_tx_dma_buffers = 1;
4170 info->num_tx_holding_buffers = 0;
4171 }
4172
4173 return info;
4174
4175} /* end of mgsl_allocate_device()*/
4176
4177static const struct tty_operations mgsl_ops = {
4178 .install = mgsl_install,
4179 .open = mgsl_open,
4180 .close = mgsl_close,
4181 .write = mgsl_write,
4182 .put_char = mgsl_put_char,
4183 .flush_chars = mgsl_flush_chars,
4184 .write_room = mgsl_write_room,
4185 .chars_in_buffer = mgsl_chars_in_buffer,
4186 .flush_buffer = mgsl_flush_buffer,
4187 .ioctl = mgsl_ioctl,
4188 .throttle = mgsl_throttle,
4189 .unthrottle = mgsl_unthrottle,
4190 .send_xchar = mgsl_send_xchar,
4191 .break_ctl = mgsl_break,
4192 .wait_until_sent = mgsl_wait_until_sent,
4193 .set_termios = mgsl_set_termios,
4194 .stop = mgsl_stop,
4195 .start = mgsl_start,
4196 .hangup = mgsl_hangup,
4197 .tiocmget = tiocmget,
4198 .tiocmset = tiocmset,
4199 .get_icount = msgl_get_icount,
4200 .proc_show = mgsl_proc_show,
4201};
4202
4203/*
4204 * perform tty device initialization
4205 */
4206static int mgsl_init_tty(void)
4207{
4208 int rc;
4209
4210 serial_driver = alloc_tty_driver(128);
4211 if (!serial_driver)
4212 return -ENOMEM;
4213
4214 serial_driver->driver_name = "synclink";
4215 serial_driver->name = "ttySL";
4216 serial_driver->major = ttymajor;
4217 serial_driver->minor_start = 64;
4218 serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
4219 serial_driver->subtype = SERIAL_TYPE_NORMAL;
4220 serial_driver->init_termios = tty_std_termios;
4221 serial_driver->init_termios.c_cflag =
4222 B9600 | CS8 | CREAD | HUPCL | CLOCAL;
4223 serial_driver->init_termios.c_ispeed = 9600;
4224 serial_driver->init_termios.c_ospeed = 9600;
4225 serial_driver->flags = TTY_DRIVER_REAL_RAW;
4226 tty_set_operations(serial_driver, &mgsl_ops);
4227 if ((rc = tty_register_driver(serial_driver)) < 0) {
4228 printk("%s(%d):Couldn't register serial driver\n",
4229 __FILE__,__LINE__);
4230 put_tty_driver(serial_driver);
4231 serial_driver = NULL;
4232 return rc;
4233 }
4234
4235 printk("%s %s, tty major#%d\n",
4236 driver_name, driver_version,
4237 serial_driver->major);
4238 return 0;
4239}
4240
4241static void synclink_cleanup(void)
4242{
4243 int rc;
4244 struct mgsl_struct *info;
4245 struct mgsl_struct *tmp;
4246
4247 printk("Unloading %s: %s\n", driver_name, driver_version);
4248
4249 if (serial_driver) {
4250 rc = tty_unregister_driver(serial_driver);
4251 if (rc)
4252 printk("%s(%d) failed to unregister tty driver err=%d\n",
4253 __FILE__,__LINE__,rc);
4254 put_tty_driver(serial_driver);
4255 }
4256
4257 info = mgsl_device_list;
4258 while(info) {
4259#if SYNCLINK_GENERIC_HDLC
4260 hdlcdev_exit(info);
4261#endif
4262 mgsl_release_resources(info);
4263 tmp = info;
4264 info = info->next_device;
4265 tty_port_destroy(&tmp->port);
4266 kfree(tmp);
4267 }
4268
4269 if (pci_registered)
4270 pci_unregister_driver(&synclink_pci_driver);
4271}
4272
4273static int __init synclink_init(void)
4274{
4275 int rc;
4276
4277 if (break_on_load) {
4278 mgsl_get_text_ptr();
4279 BREAKPOINT();
4280 }
4281
4282 printk("%s %s\n", driver_name, driver_version);
4283
4284 if ((rc = pci_register_driver(&synclink_pci_driver)) < 0)
4285 printk("%s:failed to register PCI driver, error=%d\n",__FILE__,rc);
4286 else
4287 pci_registered = true;
4288
4289 if ((rc = mgsl_init_tty()) < 0)
4290 goto error;
4291
4292 return 0;
4293
4294error:
4295 synclink_cleanup();
4296 return rc;
4297}
4298
4299static void __exit synclink_exit(void)
4300{
4301 synclink_cleanup();
4302}
4303
4304module_init(synclink_init);
4305module_exit(synclink_exit);
4306
4307/*
4308 * usc_RTCmd()
4309 *
4310 * Issue a USC Receive/Transmit command to the
4311 * Channel Command/Address Register (CCAR).
4312 *
4313 * Notes:
4314 *
4315 * The command is encoded in the most significant 5 bits <15..11>
4316 * of the CCAR value. Bits <10..7> of the CCAR must be preserved
4317 * and Bits <6..0> must be written as zeros.
4318 *
4319 * Arguments:
4320 *
4321 * info pointer to device information structure
4322 * Cmd command mask (use symbolic macros)
4323 *
4324 * Return Value:
4325 *
4326 * None
4327 */
4328static void usc_RTCmd( struct mgsl_struct *info, u16 Cmd )
4329{
4330 /* output command to CCAR in bits <15..11> */
4331 /* preserve bits <10..7>, bits <6..0> must be zero */
4332
4333 outw( Cmd + info->loopback_bits, info->io_base + CCAR );
4334
4335 /* Read to flush write to CCAR */
4336 inw( info->io_base + CCAR );
4337
4338} /* end of usc_RTCmd() */
4339
4340/*
4341 * usc_DmaCmd()
4342 *
4343 * Issue a DMA command to the DMA Command/Address Register (DCAR).
4344 *
4345 * Arguments:
4346 *
4347 * info pointer to device information structure
4348 * Cmd DMA command mask (usc_DmaCmd_XX Macros)
4349 *
4350 * Return Value:
4351 *
4352 * None
4353 */
4354static void usc_DmaCmd( struct mgsl_struct *info, u16 Cmd )
4355{
4356 /* write command mask to DCAR */
4357 outw( Cmd + info->mbre_bit, info->io_base );
4358
4359 /* Read to flush write to DCAR */
4360 inw( info->io_base );
4361
4362} /* end of usc_DmaCmd() */
4363
4364/*
4365 * usc_OutDmaReg()
4366 *
4367 * Write a 16-bit value to a USC DMA register
4368 *
4369 * Arguments:
4370 *
4371 * info pointer to device info structure
4372 * RegAddr register address (number) for write
4373 * RegValue 16-bit value to write to register
4374 *
4375 * Return Value:
4376 *
4377 * None
4378 *
4379 */
4380static void usc_OutDmaReg( struct mgsl_struct *info, u16 RegAddr, u16 RegValue )
4381{
4382 /* Note: The DCAR is located at the adapter base address */
4383 /* Note: must preserve state of BIT8 in DCAR */
4384
4385 outw( RegAddr + info->mbre_bit, info->io_base );
4386 outw( RegValue, info->io_base );
4387
4388 /* Read to flush write to DCAR */
4389 inw( info->io_base );
4390
4391} /* end of usc_OutDmaReg() */
4392
4393/*
4394 * usc_InDmaReg()
4395 *
4396 * Read a 16-bit value from a DMA register
4397 *
4398 * Arguments:
4399 *
4400 * info pointer to device info structure
4401 * RegAddr register address (number) to read from
4402 *
4403 * Return Value:
4404 *
4405 * The 16-bit value read from register
4406 *
4407 */
4408static u16 usc_InDmaReg( struct mgsl_struct *info, u16 RegAddr )
4409{
4410 /* Note: The DCAR is located at the adapter base address */
4411 /* Note: must preserve state of BIT8 in DCAR */
4412
4413 outw( RegAddr + info->mbre_bit, info->io_base );
4414 return inw( info->io_base );
4415
4416} /* end of usc_InDmaReg() */
4417
4418/*
4419 *
4420 * usc_OutReg()
4421 *
4422 * Write a 16-bit value to a USC serial channel register
4423 *
4424 * Arguments:
4425 *
4426 * info pointer to device info structure
4427 * RegAddr register address (number) to write to
4428 * RegValue 16-bit value to write to register
4429 *
4430 * Return Value:
4431 *
4432 * None
4433 *
4434 */
4435static void usc_OutReg( struct mgsl_struct *info, u16 RegAddr, u16 RegValue )
4436{
4437 outw( RegAddr + info->loopback_bits, info->io_base + CCAR );
4438 outw( RegValue, info->io_base + CCAR );
4439
4440 /* Read to flush write to CCAR */
4441 inw( info->io_base + CCAR );
4442
4443} /* end of usc_OutReg() */
4444
4445/*
4446 * usc_InReg()
4447 *
4448 * Reads a 16-bit value from a USC serial channel register
4449 *
4450 * Arguments:
4451 *
4452 * info pointer to device extension
4453 * RegAddr register address (number) to read from
4454 *
4455 * Return Value:
4456 *
4457 * 16-bit value read from register
4458 */
4459static u16 usc_InReg( struct mgsl_struct *info, u16 RegAddr )
4460{
4461 outw( RegAddr + info->loopback_bits, info->io_base + CCAR );
4462 return inw( info->io_base + CCAR );
4463
4464} /* end of usc_InReg() */
4465
4466/* usc_set_sdlc_mode()
4467 *
4468 * Set up the adapter for SDLC DMA communications.
4469 *
4470 * Arguments: info pointer to device instance data
4471 * Return Value: NONE
4472 */
4473static void usc_set_sdlc_mode( struct mgsl_struct *info )
4474{
4475 u16 RegValue;
4476 bool PreSL1660;
4477
4478 /*
4479 * determine if the IUSC on the adapter is pre-SL1660. If
4480 * not, take advantage of the UnderWait feature of more
4481 * modern chips. If an underrun occurs and this bit is set,
4482 * the transmitter will idle the programmed idle pattern
4483 * until the driver has time to service the underrun. Otherwise,
4484 * the dma controller may get the cycles previously requested
4485 * and begin transmitting queued tx data.
4486 */
4487 usc_OutReg(info,TMCR,0x1f);
4488 RegValue=usc_InReg(info,TMDR);
4489 PreSL1660 = (RegValue == IUSC_PRE_SL1660);
4490
4491 if ( info->params.flags & HDLC_FLAG_HDLC_LOOPMODE )
4492 {
4493 /*
4494 ** Channel Mode Register (CMR)
4495 **
4496 ** <15..14> 10 Tx Sub Modes, Send Flag on Underrun
4497 ** <13> 0 0 = Transmit Disabled (initially)
4498 ** <12> 0 1 = Consecutive Idles share common 0
4499 ** <11..8> 1110 Transmitter Mode = HDLC/SDLC Loop
4500 ** <7..4> 0000 Rx Sub Modes, addr/ctrl field handling
4501 ** <3..0> 0110 Receiver Mode = HDLC/SDLC
4502 **
4503 ** 1000 1110 0000 0110 = 0x8e06
4504 */
4505 RegValue = 0x8e06;
4506
4507 /*--------------------------------------------------
4508 * ignore user options for UnderRun Actions and
4509 * preambles
4510 *--------------------------------------------------*/
4511 }
4512 else
4513 {
4514 /* Channel mode Register (CMR)
4515 *
4516 * <15..14> 00 Tx Sub modes, Underrun Action
4517 * <13> 0 1 = Send Preamble before opening flag
4518 * <12> 0 1 = Consecutive Idles share common 0
4519 * <11..8> 0110 Transmitter mode = HDLC/SDLC
4520 * <7..4> 0000 Rx Sub modes, addr/ctrl field handling
4521 * <3..0> 0110 Receiver mode = HDLC/SDLC
4522 *
4523 * 0000 0110 0000 0110 = 0x0606
4524 */
4525 if (info->params.mode == MGSL_MODE_RAW) {
4526 RegValue = 0x0001; /* Set Receive mode = external sync */
4527
4528 usc_OutReg( info, IOCR, /* Set IOCR DCD is RxSync Detect Input */
4529 (unsigned short)((usc_InReg(info, IOCR) & ~(BIT13|BIT12)) | BIT12));
4530
4531 /*
4532 * TxSubMode:
4533 * CMR <15> 0 Don't send CRC on Tx Underrun
4534 * CMR <14> x undefined
4535 * CMR <13> 0 Send preamble before openning sync
4536 * CMR <12> 0 Send 8-bit syncs, 1=send Syncs per TxLength
4537 *
4538 * TxMode:
4539 * CMR <11-8) 0100 MonoSync
4540 *
4541 * 0x00 0100 xxxx xxxx 04xx
4542 */
4543 RegValue |= 0x0400;
4544 }
4545 else {
4546
4547 RegValue = 0x0606;
4548
4549 if ( info->params.flags & HDLC_FLAG_UNDERRUN_ABORT15 )
4550 RegValue |= BIT14;
4551 else if ( info->params.flags & HDLC_FLAG_UNDERRUN_FLAG )
4552 RegValue |= BIT15;
4553 else if ( info->params.flags & HDLC_FLAG_UNDERRUN_CRC )
4554 RegValue |= BIT15 | BIT14;
4555 }
4556
4557 if ( info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE )
4558 RegValue |= BIT13;
4559 }
4560
4561 if ( info->params.mode == MGSL_MODE_HDLC &&
4562 (info->params.flags & HDLC_FLAG_SHARE_ZERO) )
4563 RegValue |= BIT12;
4564
4565 if ( info->params.addr_filter != 0xff )
4566 {
4567 /* set up receive address filtering */
4568 usc_OutReg( info, RSR, info->params.addr_filter );
4569 RegValue |= BIT4;
4570 }
4571
4572 usc_OutReg( info, CMR, RegValue );
4573 info->cmr_value = RegValue;
4574
4575 /* Receiver mode Register (RMR)
4576 *
4577 * <15..13> 000 encoding
4578 * <12..11> 00 FCS = 16bit CRC CCITT (x15 + x12 + x5 + 1)
4579 * <10> 1 1 = Set CRC to all 1s (use for SDLC/HDLC)
4580 * <9> 0 1 = Include Receive chars in CRC
4581 * <8> 1 1 = Use Abort/PE bit as abort indicator
4582 * <7..6> 00 Even parity
4583 * <5> 0 parity disabled
4584 * <4..2> 000 Receive Char Length = 8 bits
4585 * <1..0> 00 Disable Receiver
4586 *
4587 * 0000 0101 0000 0000 = 0x0500
4588 */
4589
4590 RegValue = 0x0500;
4591
4592 switch ( info->params.encoding ) {
4593 case HDLC_ENCODING_NRZB: RegValue |= BIT13; break;
4594 case HDLC_ENCODING_NRZI_MARK: RegValue |= BIT14; break;
4595 case HDLC_ENCODING_NRZI_SPACE: RegValue |= BIT14 | BIT13; break;
4596 case HDLC_ENCODING_BIPHASE_MARK: RegValue |= BIT15; break;
4597 case HDLC_ENCODING_BIPHASE_SPACE: RegValue |= BIT15 | BIT13; break;
4598 case HDLC_ENCODING_BIPHASE_LEVEL: RegValue |= BIT15 | BIT14; break;
4599 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: RegValue |= BIT15 | BIT14 | BIT13; break;
4600 }
4601
4602 if ( (info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_16_CCITT )
4603 RegValue |= BIT9;
4604 else if ( (info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_32_CCITT )
4605 RegValue |= ( BIT12 | BIT10 | BIT9 );
4606
4607 usc_OutReg( info, RMR, RegValue );
4608
4609 /* Set the Receive count Limit Register (RCLR) to 0xffff. */
4610 /* When an opening flag of an SDLC frame is recognized the */
4611 /* Receive Character count (RCC) is loaded with the value in */
4612 /* RCLR. The RCC is decremented for each received byte. The */
4613 /* value of RCC is stored after the closing flag of the frame */
4614 /* allowing the frame size to be computed. */
4615
4616 usc_OutReg( info, RCLR, RCLRVALUE );
4617
4618 usc_RCmd( info, RCmd_SelectRicrdma_level );
4619
4620 /* Receive Interrupt Control Register (RICR)
4621 *
4622 * <15..8> ? RxFIFO DMA Request Level
4623 * <7> 0 Exited Hunt IA (Interrupt Arm)
4624 * <6> 0 Idle Received IA
4625 * <5> 0 Break/Abort IA
4626 * <4> 0 Rx Bound IA
4627 * <3> 1 Queued status reflects oldest 2 bytes in FIFO
4628 * <2> 0 Abort/PE IA
4629 * <1> 1 Rx Overrun IA
4630 * <0> 0 Select TC0 value for readback
4631 *
4632 * 0000 0000 0000 1000 = 0x000a
4633 */
4634
4635 /* Carry over the Exit Hunt and Idle Received bits */
4636 /* in case they have been armed by usc_ArmEvents. */
4637
4638 RegValue = usc_InReg( info, RICR ) & 0xc0;
4639
4640 usc_OutReg( info, RICR, (u16)(0x030a | RegValue) );
4641
4642 /* Unlatch all Rx status bits and clear Rx status IRQ Pending */
4643
4644 usc_UnlatchRxstatusBits( info, RXSTATUS_ALL );
4645 usc_ClearIrqPendingBits( info, RECEIVE_STATUS );
4646
4647 /* Transmit mode Register (TMR)
4648 *
4649 * <15..13> 000 encoding
4650 * <12..11> 00 FCS = 16bit CRC CCITT (x15 + x12 + x5 + 1)
4651 * <10> 1 1 = Start CRC as all 1s (use for SDLC/HDLC)
4652 * <9> 0 1 = Tx CRC Enabled
4653 * <8> 0 1 = Append CRC to end of transmit frame
4654 * <7..6> 00 Transmit parity Even
4655 * <5> 0 Transmit parity Disabled
4656 * <4..2> 000 Tx Char Length = 8 bits
4657 * <1..0> 00 Disable Transmitter
4658 *
4659 * 0000 0100 0000 0000 = 0x0400
4660 */
4661
4662 RegValue = 0x0400;
4663
4664 switch ( info->params.encoding ) {
4665 case HDLC_ENCODING_NRZB: RegValue |= BIT13; break;
4666 case HDLC_ENCODING_NRZI_MARK: RegValue |= BIT14; break;
4667 case HDLC_ENCODING_NRZI_SPACE: RegValue |= BIT14 | BIT13; break;
4668 case HDLC_ENCODING_BIPHASE_MARK: RegValue |= BIT15; break;
4669 case HDLC_ENCODING_BIPHASE_SPACE: RegValue |= BIT15 | BIT13; break;
4670 case HDLC_ENCODING_BIPHASE_LEVEL: RegValue |= BIT15 | BIT14; break;
4671 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: RegValue |= BIT15 | BIT14 | BIT13; break;
4672 }
4673
4674 if ( (info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_16_CCITT )
4675 RegValue |= BIT9 | BIT8;
4676 else if ( (info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_32_CCITT )
4677 RegValue |= ( BIT12 | BIT10 | BIT9 | BIT8);
4678
4679 usc_OutReg( info, TMR, RegValue );
4680
4681 usc_set_txidle( info );
4682
4683
4684 usc_TCmd( info, TCmd_SelectTicrdma_level );
4685
4686 /* Transmit Interrupt Control Register (TICR)
4687 *
4688 * <15..8> ? Transmit FIFO DMA Level
4689 * <7> 0 Present IA (Interrupt Arm)
4690 * <6> 0 Idle Sent IA
4691 * <5> 1 Abort Sent IA
4692 * <4> 1 EOF/EOM Sent IA
4693 * <3> 0 CRC Sent IA
4694 * <2> 1 1 = Wait for SW Trigger to Start Frame
4695 * <1> 1 Tx Underrun IA
4696 * <0> 0 TC0 constant on read back
4697 *
4698 * 0000 0000 0011 0110 = 0x0036
4699 */
4700
4701 usc_OutReg( info, TICR, 0x0736 );
4702
4703 usc_UnlatchTxstatusBits( info, TXSTATUS_ALL );
4704 usc_ClearIrqPendingBits( info, TRANSMIT_STATUS );
4705
4706 /*
4707 ** Transmit Command/Status Register (TCSR)
4708 **
4709 ** <15..12> 0000 TCmd
4710 ** <11> 0/1 UnderWait
4711 ** <10..08> 000 TxIdle
4712 ** <7> x PreSent
4713 ** <6> x IdleSent
4714 ** <5> x AbortSent
4715 ** <4> x EOF/EOM Sent
4716 ** <3> x CRC Sent
4717 ** <2> x All Sent
4718 ** <1> x TxUnder
4719 ** <0> x TxEmpty
4720 **
4721 ** 0000 0000 0000 0000 = 0x0000
4722 */
4723 info->tcsr_value = 0;
4724
4725 if ( !PreSL1660 )
4726 info->tcsr_value |= TCSR_UNDERWAIT;
4727
4728 usc_OutReg( info, TCSR, info->tcsr_value );
4729
4730 /* Clock mode Control Register (CMCR)
4731 *
4732 * <15..14> 00 counter 1 Source = Disabled
4733 * <13..12> 00 counter 0 Source = Disabled
4734 * <11..10> 11 BRG1 Input is TxC Pin
4735 * <9..8> 11 BRG0 Input is TxC Pin
4736 * <7..6> 01 DPLL Input is BRG1 Output
4737 * <5..3> XXX TxCLK comes from Port 0
4738 * <2..0> XXX RxCLK comes from Port 1
4739 *
4740 * 0000 1111 0111 0111 = 0x0f77
4741 */
4742
4743 RegValue = 0x0f40;
4744
4745 if ( info->params.flags & HDLC_FLAG_RXC_DPLL )
4746 RegValue |= 0x0003; /* RxCLK from DPLL */
4747 else if ( info->params.flags & HDLC_FLAG_RXC_BRG )
4748 RegValue |= 0x0004; /* RxCLK from BRG0 */
4749 else if ( info->params.flags & HDLC_FLAG_RXC_TXCPIN)
4750 RegValue |= 0x0006; /* RxCLK from TXC Input */
4751 else
4752 RegValue |= 0x0007; /* RxCLK from Port1 */
4753
4754 if ( info->params.flags & HDLC_FLAG_TXC_DPLL )
4755 RegValue |= 0x0018; /* TxCLK from DPLL */
4756 else if ( info->params.flags & HDLC_FLAG_TXC_BRG )
4757 RegValue |= 0x0020; /* TxCLK from BRG0 */
4758 else if ( info->params.flags & HDLC_FLAG_TXC_RXCPIN)
4759 RegValue |= 0x0038; /* RxCLK from TXC Input */
4760 else
4761 RegValue |= 0x0030; /* TxCLK from Port0 */
4762
4763 usc_OutReg( info, CMCR, RegValue );
4764
4765
4766 /* Hardware Configuration Register (HCR)
4767 *
4768 * <15..14> 00 CTR0 Divisor:00=32,01=16,10=8,11=4
4769 * <13> 0 CTR1DSel:0=CTR0Div determines CTR0Div
4770 * <12> 0 CVOK:0=report code violation in biphase
4771 * <11..10> 00 DPLL Divisor:00=32,01=16,10=8,11=4
4772 * <9..8> XX DPLL mode:00=disable,01=NRZ,10=Biphase,11=Biphase Level
4773 * <7..6> 00 reserved
4774 * <5> 0 BRG1 mode:0=continuous,1=single cycle
4775 * <4> X BRG1 Enable
4776 * <3..2> 00 reserved
4777 * <1> 0 BRG0 mode:0=continuous,1=single cycle
4778 * <0> 0 BRG0 Enable
4779 */
4780
4781 RegValue = 0x0000;
4782
4783 if ( info->params.flags & (HDLC_FLAG_RXC_DPLL | HDLC_FLAG_TXC_DPLL) ) {
4784 u32 XtalSpeed;
4785 u32 DpllDivisor;
4786 u16 Tc;
4787
4788 /* DPLL is enabled. Use BRG1 to provide continuous reference clock */
4789 /* for DPLL. DPLL mode in HCR is dependent on the encoding used. */
4790
4791 XtalSpeed = 11059200;
4792
4793 if ( info->params.flags & HDLC_FLAG_DPLL_DIV16 ) {
4794 DpllDivisor = 16;
4795 RegValue |= BIT10;
4796 }
4797 else if ( info->params.flags & HDLC_FLAG_DPLL_DIV8 ) {
4798 DpllDivisor = 8;
4799 RegValue |= BIT11;
4800 }
4801 else
4802 DpllDivisor = 32;
4803
4804 /* Tc = (Xtal/Speed) - 1 */
4805 /* If twice the remainder of (Xtal/Speed) is greater than Speed */
4806 /* then rounding up gives a more precise time constant. Instead */
4807 /* of rounding up and then subtracting 1 we just don't subtract */
4808 /* the one in this case. */
4809
4810 /*--------------------------------------------------
4811 * ejz: for DPLL mode, application should use the
4812 * same clock speed as the partner system, even
4813 * though clocking is derived from the input RxData.
4814 * In case the user uses a 0 for the clock speed,
4815 * default to 0xffffffff and don't try to divide by
4816 * zero
4817 *--------------------------------------------------*/
4818 if ( info->params.clock_speed )
4819 {
4820 Tc = (u16)((XtalSpeed/DpllDivisor)/info->params.clock_speed);
4821 if ( !((((XtalSpeed/DpllDivisor) % info->params.clock_speed) * 2)
4822 / info->params.clock_speed) )
4823 Tc--;
4824 }
4825 else
4826 Tc = -1;
4827
4828
4829 /* Write 16-bit Time Constant for BRG1 */
4830 usc_OutReg( info, TC1R, Tc );
4831
4832 RegValue |= BIT4; /* enable BRG1 */
4833
4834 switch ( info->params.encoding ) {
4835 case HDLC_ENCODING_NRZ:
4836 case HDLC_ENCODING_NRZB:
4837 case HDLC_ENCODING_NRZI_MARK:
4838 case HDLC_ENCODING_NRZI_SPACE: RegValue |= BIT8; break;
4839 case HDLC_ENCODING_BIPHASE_MARK:
4840 case HDLC_ENCODING_BIPHASE_SPACE: RegValue |= BIT9; break;
4841 case HDLC_ENCODING_BIPHASE_LEVEL:
4842 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: RegValue |= BIT9 | BIT8; break;
4843 }
4844 }
4845
4846 usc_OutReg( info, HCR, RegValue );
4847
4848
4849 /* Channel Control/status Register (CCSR)
4850 *
4851 * <15> X RCC FIFO Overflow status (RO)
4852 * <14> X RCC FIFO Not Empty status (RO)
4853 * <13> 0 1 = Clear RCC FIFO (WO)
4854 * <12> X DPLL Sync (RW)
4855 * <11> X DPLL 2 Missed Clocks status (RO)
4856 * <10> X DPLL 1 Missed Clock status (RO)
4857 * <9..8> 00 DPLL Resync on rising and falling edges (RW)
4858 * <7> X SDLC Loop On status (RO)
4859 * <6> X SDLC Loop Send status (RO)
4860 * <5> 1 Bypass counters for TxClk and RxClk (RW)
4861 * <4..2> 000 Last Char of SDLC frame has 8 bits (RW)
4862 * <1..0> 00 reserved
4863 *
4864 * 0000 0000 0010 0000 = 0x0020
4865 */
4866
4867 usc_OutReg( info, CCSR, 0x1020 );
4868
4869
4870 if ( info->params.flags & HDLC_FLAG_AUTO_CTS ) {
4871 usc_OutReg( info, SICR,
4872 (u16)(usc_InReg(info,SICR) | SICR_CTS_INACTIVE) );
4873 }
4874
4875
4876 /* enable Master Interrupt Enable bit (MIE) */
4877 usc_EnableMasterIrqBit( info );
4878
4879 usc_ClearIrqPendingBits( info, RECEIVE_STATUS | RECEIVE_DATA |
4880 TRANSMIT_STATUS | TRANSMIT_DATA | MISC);
4881
4882 /* arm RCC underflow interrupt */
4883 usc_OutReg(info, SICR, (u16)(usc_InReg(info,SICR) | BIT3));
4884 usc_EnableInterrupts(info, MISC);
4885
4886 info->mbre_bit = 0;
4887 outw( 0, info->io_base ); /* clear Master Bus Enable (DCAR) */
4888 usc_DmaCmd( info, DmaCmd_ResetAllChannels ); /* disable both DMA channels */
4889 info->mbre_bit = BIT8;
4890 outw( BIT8, info->io_base ); /* set Master Bus Enable (DCAR) */
4891
4892 /* DMA Control Register (DCR)
4893 *
4894 * <15..14> 10 Priority mode = Alternating Tx/Rx
4895 * 01 Rx has priority
4896 * 00 Tx has priority
4897 *
4898 * <13> 1 Enable Priority Preempt per DCR<15..14>
4899 * (WARNING DCR<11..10> must be 00 when this is 1)
4900 * 0 Choose activate channel per DCR<11..10>
4901 *
4902 * <12> 0 Little Endian for Array/List
4903 * <11..10> 00 Both Channels can use each bus grant
4904 * <9..6> 0000 reserved
4905 * <5> 0 7 CLK - Minimum Bus Re-request Interval
4906 * <4> 0 1 = drive D/C and S/D pins
4907 * <3> 1 1 = Add one wait state to all DMA cycles.
4908 * <2> 0 1 = Strobe /UAS on every transfer.
4909 * <1..0> 11 Addr incrementing only affects LS24 bits
4910 *
4911 * 0110 0000 0000 1011 = 0x600b
4912 */
4913
4914 /* PCI adapter does not need DMA wait state */
4915 usc_OutDmaReg( info, DCR, 0xa00b );
4916
4917 /* Receive DMA mode Register (RDMR)
4918 *
4919 * <15..14> 11 DMA mode = Linked List Buffer mode
4920 * <13> 1 RSBinA/L = store Rx status Block in Arrary/List entry
4921 * <12> 1 Clear count of List Entry after fetching
4922 * <11..10> 00 Address mode = Increment
4923 * <9> 1 Terminate Buffer on RxBound
4924 * <8> 0 Bus Width = 16bits
4925 * <7..0> ? status Bits (write as 0s)
4926 *
4927 * 1111 0010 0000 0000 = 0xf200
4928 */
4929
4930 usc_OutDmaReg( info, RDMR, 0xf200 );
4931
4932
4933 /* Transmit DMA mode Register (TDMR)
4934 *
4935 * <15..14> 11 DMA mode = Linked List Buffer mode
4936 * <13> 1 TCBinA/L = fetch Tx Control Block from List entry
4937 * <12> 1 Clear count of List Entry after fetching
4938 * <11..10> 00 Address mode = Increment
4939 * <9> 1 Terminate Buffer on end of frame
4940 * <8> 0 Bus Width = 16bits
4941 * <7..0> ? status Bits (Read Only so write as 0)
4942 *
4943 * 1111 0010 0000 0000 = 0xf200
4944 */
4945
4946 usc_OutDmaReg( info, TDMR, 0xf200 );
4947
4948
4949 /* DMA Interrupt Control Register (DICR)
4950 *
4951 * <15> 1 DMA Interrupt Enable
4952 * <14> 0 1 = Disable IEO from USC
4953 * <13> 0 1 = Don't provide vector during IntAck
4954 * <12> 1 1 = Include status in Vector
4955 * <10..2> 0 reserved, Must be 0s
4956 * <1> 0 1 = Rx DMA Interrupt Enabled
4957 * <0> 0 1 = Tx DMA Interrupt Enabled
4958 *
4959 * 1001 0000 0000 0000 = 0x9000
4960 */
4961
4962 usc_OutDmaReg( info, DICR, 0x9000 );
4963
4964 usc_InDmaReg( info, RDMR ); /* clear pending receive DMA IRQ bits */
4965 usc_InDmaReg( info, TDMR ); /* clear pending transmit DMA IRQ bits */
4966 usc_OutDmaReg( info, CDIR, 0x0303 ); /* clear IUS and Pending for Tx and Rx */
4967
4968 /* Channel Control Register (CCR)
4969 *
4970 * <15..14> 10 Use 32-bit Tx Control Blocks (TCBs)
4971 * <13> 0 Trigger Tx on SW Command Disabled
4972 * <12> 0 Flag Preamble Disabled
4973 * <11..10> 00 Preamble Length
4974 * <9..8> 00 Preamble Pattern
4975 * <7..6> 10 Use 32-bit Rx status Blocks (RSBs)
4976 * <5> 0 Trigger Rx on SW Command Disabled
4977 * <4..0> 0 reserved
4978 *
4979 * 1000 0000 1000 0000 = 0x8080
4980 */
4981
4982 RegValue = 0x8080;
4983
4984 switch ( info->params.preamble_length ) {
4985 case HDLC_PREAMBLE_LENGTH_16BITS: RegValue |= BIT10; break;
4986 case HDLC_PREAMBLE_LENGTH_32BITS: RegValue |= BIT11; break;
4987 case HDLC_PREAMBLE_LENGTH_64BITS: RegValue |= BIT11 | BIT10; break;
4988 }
4989
4990 switch ( info->params.preamble ) {
4991 case HDLC_PREAMBLE_PATTERN_FLAGS: RegValue |= BIT8 | BIT12; break;
4992 case HDLC_PREAMBLE_PATTERN_ONES: RegValue |= BIT8; break;
4993 case HDLC_PREAMBLE_PATTERN_10: RegValue |= BIT9; break;
4994 case HDLC_PREAMBLE_PATTERN_01: RegValue |= BIT9 | BIT8; break;
4995 }
4996
4997 usc_OutReg( info, CCR, RegValue );
4998
4999
5000 /*
5001 * Burst/Dwell Control Register
5002 *
5003 * <15..8> 0x20 Maximum number of transfers per bus grant
5004 * <7..0> 0x00 Maximum number of clock cycles per bus grant
5005 */
5006
5007 /* don't limit bus occupancy on PCI adapter */
5008 usc_OutDmaReg( info, BDCR, 0x0000 );
5009
5010 usc_stop_transmitter(info);
5011 usc_stop_receiver(info);
5012
5013} /* end of usc_set_sdlc_mode() */
5014
5015/* usc_enable_loopback()
5016 *
5017 * Set the 16C32 for internal loopback mode.
5018 * The TxCLK and RxCLK signals are generated from the BRG0 and
5019 * the TxD is looped back to the RxD internally.
5020 *
5021 * Arguments: info pointer to device instance data
5022 * enable 1 = enable loopback, 0 = disable
5023 * Return Value: None
5024 */
5025static void usc_enable_loopback(struct mgsl_struct *info, int enable)
5026{
5027 if (enable) {
5028 /* blank external TXD output */
5029 usc_OutReg(info,IOCR,usc_InReg(info,IOCR) | (BIT7 | BIT6));
5030
5031 /* Clock mode Control Register (CMCR)
5032 *
5033 * <15..14> 00 counter 1 Disabled
5034 * <13..12> 00 counter 0 Disabled
5035 * <11..10> 11 BRG1 Input is TxC Pin
5036 * <9..8> 11 BRG0 Input is TxC Pin
5037 * <7..6> 01 DPLL Input is BRG1 Output
5038 * <5..3> 100 TxCLK comes from BRG0
5039 * <2..0> 100 RxCLK comes from BRG0
5040 *
5041 * 0000 1111 0110 0100 = 0x0f64
5042 */
5043
5044 usc_OutReg( info, CMCR, 0x0f64 );
5045
5046 /* Write 16-bit Time Constant for BRG0 */
5047 /* use clock speed if available, otherwise use 8 for diagnostics */
5048 if (info->params.clock_speed) {
5049 usc_OutReg(info, TC0R, (u16)((11059200/info->params.clock_speed)-1));
5050 } else
5051 usc_OutReg(info, TC0R, (u16)8);
5052
5053 /* Hardware Configuration Register (HCR) Clear Bit 1, BRG0
5054 mode = Continuous Set Bit 0 to enable BRG0. */
5055 usc_OutReg( info, HCR, (u16)((usc_InReg( info, HCR ) & ~BIT1) | BIT0) );
5056
5057 /* Input/Output Control Reg, <2..0> = 100, Drive RxC pin with BRG0 */
5058 usc_OutReg(info, IOCR, (u16)((usc_InReg(info, IOCR) & 0xfff8) | 0x0004));
5059
5060 /* set Internal Data loopback mode */
5061 info->loopback_bits = 0x300;
5062 outw( 0x0300, info->io_base + CCAR );
5063 } else {
5064 /* enable external TXD output */
5065 usc_OutReg(info,IOCR,usc_InReg(info,IOCR) & ~(BIT7 | BIT6));
5066
5067 /* clear Internal Data loopback mode */
5068 info->loopback_bits = 0;
5069 outw( 0,info->io_base + CCAR );
5070 }
5071
5072} /* end of usc_enable_loopback() */
5073
5074/* usc_enable_aux_clock()
5075 *
5076 * Enabled the AUX clock output at the specified frequency.
5077 *
5078 * Arguments:
5079 *
5080 * info pointer to device extension
5081 * data_rate data rate of clock in bits per second
5082 * A data rate of 0 disables the AUX clock.
5083 *
5084 * Return Value: None
5085 */
5086static void usc_enable_aux_clock( struct mgsl_struct *info, u32 data_rate )
5087{
5088 u32 XtalSpeed;
5089 u16 Tc;
5090
5091 if ( data_rate ) {
5092 XtalSpeed = 11059200;
5093
5094
5095 /* Tc = (Xtal/Speed) - 1 */
5096 /* If twice the remainder of (Xtal/Speed) is greater than Speed */
5097 /* then rounding up gives a more precise time constant. Instead */
5098 /* of rounding up and then subtracting 1 we just don't subtract */
5099 /* the one in this case. */
5100
5101
5102 Tc = (u16)(XtalSpeed/data_rate);
5103 if ( !(((XtalSpeed % data_rate) * 2) / data_rate) )
5104 Tc--;
5105
5106 /* Write 16-bit Time Constant for BRG0 */
5107 usc_OutReg( info, TC0R, Tc );
5108
5109 /*
5110 * Hardware Configuration Register (HCR)
5111 * Clear Bit 1, BRG0 mode = Continuous
5112 * Set Bit 0 to enable BRG0.
5113 */
5114
5115 usc_OutReg( info, HCR, (u16)((usc_InReg( info, HCR ) & ~BIT1) | BIT0) );
5116
5117 /* Input/Output Control Reg, <2..0> = 100, Drive RxC pin with BRG0 */
5118 usc_OutReg( info, IOCR, (u16)((usc_InReg(info, IOCR) & 0xfff8) | 0x0004) );
5119 } else {
5120 /* data rate == 0 so turn off BRG0 */
5121 usc_OutReg( info, HCR, (u16)(usc_InReg( info, HCR ) & ~BIT0) );
5122 }
5123
5124} /* end of usc_enable_aux_clock() */
5125
5126/*
5127 *
5128 * usc_process_rxoverrun_sync()
5129 *
5130 * This function processes a receive overrun by resetting the
5131 * receive DMA buffers and issuing a Purge Rx FIFO command
5132 * to allow the receiver to continue receiving.
5133 *
5134 * Arguments:
5135 *
5136 * info pointer to device extension
5137 *
5138 * Return Value: None
5139 */
5140static void usc_process_rxoverrun_sync( struct mgsl_struct *info )
5141{
5142 int start_index;
5143 int end_index;
5144 int frame_start_index;
5145 bool start_of_frame_found = false;
5146 bool end_of_frame_found = false;
5147 bool reprogram_dma = false;
5148
5149 DMABUFFERENTRY *buffer_list = info->rx_buffer_list;
5150 u32 phys_addr;
5151
5152 usc_DmaCmd( info, DmaCmd_PauseRxChannel );
5153 usc_RCmd( info, RCmd_EnterHuntmode );
5154 usc_RTCmd( info, RTCmd_PurgeRxFifo );
5155
5156 /* CurrentRxBuffer points to the 1st buffer of the next */
5157 /* possibly available receive frame. */
5158
5159 frame_start_index = start_index = end_index = info->current_rx_buffer;
5160
5161 /* Search for an unfinished string of buffers. This means */
5162 /* that a receive frame started (at least one buffer with */
5163 /* count set to zero) but there is no terminiting buffer */
5164 /* (status set to non-zero). */
5165
5166 while( !buffer_list[end_index].count )
5167 {
5168 /* Count field has been reset to zero by 16C32. */
5169 /* This buffer is currently in use. */
5170
5171 if ( !start_of_frame_found )
5172 {
5173 start_of_frame_found = true;
5174 frame_start_index = end_index;
5175 end_of_frame_found = false;
5176 }
5177
5178 if ( buffer_list[end_index].status )
5179 {
5180 /* Status field has been set by 16C32. */
5181 /* This is the last buffer of a received frame. */
5182
5183 /* We want to leave the buffers for this frame intact. */
5184 /* Move on to next possible frame. */
5185
5186 start_of_frame_found = false;
5187 end_of_frame_found = true;
5188 }
5189
5190 /* advance to next buffer entry in linked list */
5191 end_index++;
5192 if ( end_index == info->rx_buffer_count )
5193 end_index = 0;
5194
5195 if ( start_index == end_index )
5196 {
5197 /* The entire list has been searched with all Counts == 0 and */
5198 /* all Status == 0. The receive buffers are */
5199 /* completely screwed, reset all receive buffers! */
5200 mgsl_reset_rx_dma_buffers( info );
5201 frame_start_index = 0;
5202 start_of_frame_found = false;
5203 reprogram_dma = true;
5204 break;
5205 }
5206 }
5207
5208 if ( start_of_frame_found && !end_of_frame_found )
5209 {
5210 /* There is an unfinished string of receive DMA buffers */
5211 /* as a result of the receiver overrun. */
5212
5213 /* Reset the buffers for the unfinished frame */
5214 /* and reprogram the receive DMA controller to start */
5215 /* at the 1st buffer of unfinished frame. */
5216
5217 start_index = frame_start_index;
5218
5219 do
5220 {
5221 *((unsigned long *)&(info->rx_buffer_list[start_index++].count)) = DMABUFFERSIZE;
5222
5223 /* Adjust index for wrap around. */
5224 if ( start_index == info->rx_buffer_count )
5225 start_index = 0;
5226
5227 } while( start_index != end_index );
5228
5229 reprogram_dma = true;
5230 }
5231
5232 if ( reprogram_dma )
5233 {
5234 usc_UnlatchRxstatusBits(info,RXSTATUS_ALL);
5235 usc_ClearIrqPendingBits(info, RECEIVE_DATA|RECEIVE_STATUS);
5236 usc_UnlatchRxstatusBits(info, RECEIVE_DATA|RECEIVE_STATUS);
5237
5238 usc_EnableReceiver(info,DISABLE_UNCONDITIONAL);
5239
5240 /* This empties the receive FIFO and loads the RCC with RCLR */
5241 usc_OutReg( info, CCSR, (u16)(usc_InReg(info,CCSR) | BIT13) );
5242
5243 /* program 16C32 with physical address of 1st DMA buffer entry */
5244 phys_addr = info->rx_buffer_list[frame_start_index].phys_entry;
5245 usc_OutDmaReg( info, NRARL, (u16)phys_addr );
5246 usc_OutDmaReg( info, NRARU, (u16)(phys_addr >> 16) );
5247
5248 usc_UnlatchRxstatusBits( info, RXSTATUS_ALL );
5249 usc_ClearIrqPendingBits( info, RECEIVE_DATA | RECEIVE_STATUS );
5250 usc_EnableInterrupts( info, RECEIVE_STATUS );
5251
5252 /* 1. Arm End of Buffer (EOB) Receive DMA Interrupt (BIT2 of RDIAR) */
5253 /* 2. Enable Receive DMA Interrupts (BIT1 of DICR) */
5254
5255 usc_OutDmaReg( info, RDIAR, BIT3 | BIT2 );
5256 usc_OutDmaReg( info, DICR, (u16)(usc_InDmaReg(info,DICR) | BIT1) );
5257 usc_DmaCmd( info, DmaCmd_InitRxChannel );
5258 if ( info->params.flags & HDLC_FLAG_AUTO_DCD )
5259 usc_EnableReceiver(info,ENABLE_AUTO_DCD);
5260 else
5261 usc_EnableReceiver(info,ENABLE_UNCONDITIONAL);
5262 }
5263 else
5264 {
5265 /* This empties the receive FIFO and loads the RCC with RCLR */
5266 usc_OutReg( info, CCSR, (u16)(usc_InReg(info,CCSR) | BIT13) );
5267 usc_RTCmd( info, RTCmd_PurgeRxFifo );
5268 }
5269
5270} /* end of usc_process_rxoverrun_sync() */
5271
5272/* usc_stop_receiver()
5273 *
5274 * Disable USC receiver
5275 *
5276 * Arguments: info pointer to device instance data
5277 * Return Value: None
5278 */
5279static void usc_stop_receiver( struct mgsl_struct *info )
5280{
5281 if (debug_level >= DEBUG_LEVEL_ISR)
5282 printk("%s(%d):usc_stop_receiver(%s)\n",
5283 __FILE__,__LINE__, info->device_name );
5284
5285 /* Disable receive DMA channel. */
5286 /* This also disables receive DMA channel interrupts */
5287 usc_DmaCmd( info, DmaCmd_ResetRxChannel );
5288
5289 usc_UnlatchRxstatusBits( info, RXSTATUS_ALL );
5290 usc_ClearIrqPendingBits( info, RECEIVE_DATA | RECEIVE_STATUS );
5291 usc_DisableInterrupts( info, RECEIVE_DATA | RECEIVE_STATUS );
5292
5293 usc_EnableReceiver(info,DISABLE_UNCONDITIONAL);
5294
5295 /* This empties the receive FIFO and loads the RCC with RCLR */
5296 usc_OutReg( info, CCSR, (u16)(usc_InReg(info,CCSR) | BIT13) );
5297 usc_RTCmd( info, RTCmd_PurgeRxFifo );
5298
5299 info->rx_enabled = false;
5300 info->rx_overflow = false;
5301 info->rx_rcc_underrun = false;
5302
5303} /* end of stop_receiver() */
5304
5305/* usc_start_receiver()
5306 *
5307 * Enable the USC receiver
5308 *
5309 * Arguments: info pointer to device instance data
5310 * Return Value: None
5311 */
5312static void usc_start_receiver( struct mgsl_struct *info )
5313{
5314 u32 phys_addr;
5315
5316 if (debug_level >= DEBUG_LEVEL_ISR)
5317 printk("%s(%d):usc_start_receiver(%s)\n",
5318 __FILE__,__LINE__, info->device_name );
5319
5320 mgsl_reset_rx_dma_buffers( info );
5321 usc_stop_receiver( info );
5322
5323 usc_OutReg( info, CCSR, (u16)(usc_InReg(info,CCSR) | BIT13) );
5324 usc_RTCmd( info, RTCmd_PurgeRxFifo );
5325
5326 if ( info->params.mode == MGSL_MODE_HDLC ||
5327 info->params.mode == MGSL_MODE_RAW ) {
5328 /* DMA mode Transfers */
5329 /* Program the DMA controller. */
5330 /* Enable the DMA controller end of buffer interrupt. */
5331
5332 /* program 16C32 with physical address of 1st DMA buffer entry */
5333 phys_addr = info->rx_buffer_list[0].phys_entry;
5334 usc_OutDmaReg( info, NRARL, (u16)phys_addr );
5335 usc_OutDmaReg( info, NRARU, (u16)(phys_addr >> 16) );
5336
5337 usc_UnlatchRxstatusBits( info, RXSTATUS_ALL );
5338 usc_ClearIrqPendingBits( info, RECEIVE_DATA | RECEIVE_STATUS );
5339 usc_EnableInterrupts( info, RECEIVE_STATUS );
5340
5341 /* 1. Arm End of Buffer (EOB) Receive DMA Interrupt (BIT2 of RDIAR) */
5342 /* 2. Enable Receive DMA Interrupts (BIT1 of DICR) */
5343
5344 usc_OutDmaReg( info, RDIAR, BIT3 | BIT2 );
5345 usc_OutDmaReg( info, DICR, (u16)(usc_InDmaReg(info,DICR) | BIT1) );
5346 usc_DmaCmd( info, DmaCmd_InitRxChannel );
5347 if ( info->params.flags & HDLC_FLAG_AUTO_DCD )
5348 usc_EnableReceiver(info,ENABLE_AUTO_DCD);
5349 else
5350 usc_EnableReceiver(info,ENABLE_UNCONDITIONAL);
5351 } else {
5352 usc_UnlatchRxstatusBits(info, RXSTATUS_ALL);
5353 usc_ClearIrqPendingBits(info, RECEIVE_DATA | RECEIVE_STATUS);
5354 usc_EnableInterrupts(info, RECEIVE_DATA);
5355
5356 usc_RTCmd( info, RTCmd_PurgeRxFifo );
5357 usc_RCmd( info, RCmd_EnterHuntmode );
5358
5359 usc_EnableReceiver(info,ENABLE_UNCONDITIONAL);
5360 }
5361
5362 usc_OutReg( info, CCSR, 0x1020 );
5363
5364 info->rx_enabled = true;
5365
5366} /* end of usc_start_receiver() */
5367
5368/* usc_start_transmitter()
5369 *
5370 * Enable the USC transmitter and send a transmit frame if
5371 * one is loaded in the DMA buffers.
5372 *
5373 * Arguments: info pointer to device instance data
5374 * Return Value: None
5375 */
5376static void usc_start_transmitter( struct mgsl_struct *info )
5377{
5378 u32 phys_addr;
5379 unsigned int FrameSize;
5380
5381 if (debug_level >= DEBUG_LEVEL_ISR)
5382 printk("%s(%d):usc_start_transmitter(%s)\n",
5383 __FILE__,__LINE__, info->device_name );
5384
5385 if ( info->xmit_cnt ) {
5386
5387 /* If auto RTS enabled and RTS is inactive, then assert */
5388 /* RTS and set a flag indicating that the driver should */
5389 /* negate RTS when the transmission completes. */
5390
5391 info->drop_rts_on_tx_done = false;
5392
5393 if ( info->params.flags & HDLC_FLAG_AUTO_RTS ) {
5394 usc_get_serial_signals( info );
5395 if ( !(info->serial_signals & SerialSignal_RTS) ) {
5396 info->serial_signals |= SerialSignal_RTS;
5397 usc_set_serial_signals( info );
5398 info->drop_rts_on_tx_done = true;
5399 }
5400 }
5401
5402
5403 if ( info->params.mode == MGSL_MODE_ASYNC ) {
5404 if ( !info->tx_active ) {
5405 usc_UnlatchTxstatusBits(info, TXSTATUS_ALL);
5406 usc_ClearIrqPendingBits(info, TRANSMIT_STATUS + TRANSMIT_DATA);
5407 usc_EnableInterrupts(info, TRANSMIT_DATA);
5408 usc_load_txfifo(info);
5409 }
5410 } else {
5411 /* Disable transmit DMA controller while programming. */
5412 usc_DmaCmd( info, DmaCmd_ResetTxChannel );
5413
5414 /* Transmit DMA buffer is loaded, so program USC */
5415 /* to send the frame contained in the buffers. */
5416
5417 FrameSize = info->tx_buffer_list[info->start_tx_dma_buffer].rcc;
5418
5419 /* if operating in Raw sync mode, reset the rcc component
5420 * of the tx dma buffer entry, otherwise, the serial controller
5421 * will send a closing sync char after this count.
5422 */
5423 if ( info->params.mode == MGSL_MODE_RAW )
5424 info->tx_buffer_list[info->start_tx_dma_buffer].rcc = 0;
5425
5426 /* Program the Transmit Character Length Register (TCLR) */
5427 /* and clear FIFO (TCC is loaded with TCLR on FIFO clear) */
5428 usc_OutReg( info, TCLR, (u16)FrameSize );
5429
5430 usc_RTCmd( info, RTCmd_PurgeTxFifo );
5431
5432 /* Program the address of the 1st DMA Buffer Entry in linked list */
5433 phys_addr = info->tx_buffer_list[info->start_tx_dma_buffer].phys_entry;
5434 usc_OutDmaReg( info, NTARL, (u16)phys_addr );
5435 usc_OutDmaReg( info, NTARU, (u16)(phys_addr >> 16) );
5436
5437 usc_UnlatchTxstatusBits( info, TXSTATUS_ALL );
5438 usc_ClearIrqPendingBits( info, TRANSMIT_STATUS );
5439 usc_EnableInterrupts( info, TRANSMIT_STATUS );
5440
5441 if ( info->params.mode == MGSL_MODE_RAW &&
5442 info->num_tx_dma_buffers > 1 ) {
5443 /* When running external sync mode, attempt to 'stream' transmit */
5444 /* by filling tx dma buffers as they become available. To do this */
5445 /* we need to enable Tx DMA EOB Status interrupts : */
5446 /* */
5447 /* 1. Arm End of Buffer (EOB) Transmit DMA Interrupt (BIT2 of TDIAR) */
5448 /* 2. Enable Transmit DMA Interrupts (BIT0 of DICR) */
5449
5450 usc_OutDmaReg( info, TDIAR, BIT2|BIT3 );
5451 usc_OutDmaReg( info, DICR, (u16)(usc_InDmaReg(info,DICR) | BIT0) );
5452 }
5453
5454 /* Initialize Transmit DMA Channel */
5455 usc_DmaCmd( info, DmaCmd_InitTxChannel );
5456
5457 usc_TCmd( info, TCmd_SendFrame );
5458
5459 mod_timer(&info->tx_timer, jiffies +
5460 msecs_to_jiffies(5000));
5461 }
5462 info->tx_active = true;
5463 }
5464
5465 if ( !info->tx_enabled ) {
5466 info->tx_enabled = true;
5467 if ( info->params.flags & HDLC_FLAG_AUTO_CTS )
5468 usc_EnableTransmitter(info,ENABLE_AUTO_CTS);
5469 else
5470 usc_EnableTransmitter(info,ENABLE_UNCONDITIONAL);
5471 }
5472
5473} /* end of usc_start_transmitter() */
5474
5475/* usc_stop_transmitter()
5476 *
5477 * Stops the transmitter and DMA
5478 *
5479 * Arguments: info pointer to device isntance data
5480 * Return Value: None
5481 */
5482static void usc_stop_transmitter( struct mgsl_struct *info )
5483{
5484 if (debug_level >= DEBUG_LEVEL_ISR)
5485 printk("%s(%d):usc_stop_transmitter(%s)\n",
5486 __FILE__,__LINE__, info->device_name );
5487
5488 del_timer(&info->tx_timer);
5489
5490 usc_UnlatchTxstatusBits( info, TXSTATUS_ALL );
5491 usc_ClearIrqPendingBits( info, TRANSMIT_STATUS + TRANSMIT_DATA );
5492 usc_DisableInterrupts( info, TRANSMIT_STATUS + TRANSMIT_DATA );
5493
5494 usc_EnableTransmitter(info,DISABLE_UNCONDITIONAL);
5495 usc_DmaCmd( info, DmaCmd_ResetTxChannel );
5496 usc_RTCmd( info, RTCmd_PurgeTxFifo );
5497
5498 info->tx_enabled = false;
5499 info->tx_active = false;
5500
5501} /* end of usc_stop_transmitter() */
5502
5503/* usc_load_txfifo()
5504 *
5505 * Fill the transmit FIFO until the FIFO is full or
5506 * there is no more data to load.
5507 *
5508 * Arguments: info pointer to device extension (instance data)
5509 * Return Value: None
5510 */
5511static void usc_load_txfifo( struct mgsl_struct *info )
5512{
5513 int Fifocount;
5514 u8 TwoBytes[2];
5515
5516 if ( !info->xmit_cnt && !info->x_char )
5517 return;
5518
5519 /* Select transmit FIFO status readback in TICR */
5520 usc_TCmd( info, TCmd_SelectTicrTxFifostatus );
5521
5522 /* load the Transmit FIFO until FIFOs full or all data sent */
5523
5524 while( (Fifocount = usc_InReg(info, TICR) >> 8) && info->xmit_cnt ) {
5525 /* there is more space in the transmit FIFO and */
5526 /* there is more data in transmit buffer */
5527
5528 if ( (info->xmit_cnt > 1) && (Fifocount > 1) && !info->x_char ) {
5529 /* write a 16-bit word from transmit buffer to 16C32 */
5530
5531 TwoBytes[0] = info->xmit_buf[info->xmit_tail++];
5532 info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1);
5533 TwoBytes[1] = info->xmit_buf[info->xmit_tail++];
5534 info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1);
5535
5536 outw( *((u16 *)TwoBytes), info->io_base + DATAREG);
5537
5538 info->xmit_cnt -= 2;
5539 info->icount.tx += 2;
5540 } else {
5541 /* only 1 byte left to transmit or 1 FIFO slot left */
5542
5543 outw( (inw( info->io_base + CCAR) & 0x0780) | (TDR+LSBONLY),
5544 info->io_base + CCAR );
5545
5546 if (info->x_char) {
5547 /* transmit pending high priority char */
5548 outw( info->x_char,info->io_base + CCAR );
5549 info->x_char = 0;
5550 } else {
5551 outw( info->xmit_buf[info->xmit_tail++],info->io_base + CCAR );
5552 info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1);
5553 info->xmit_cnt--;
5554 }
5555 info->icount.tx++;
5556 }
5557 }
5558
5559} /* end of usc_load_txfifo() */
5560
5561/* usc_reset()
5562 *
5563 * Reset the adapter to a known state and prepare it for further use.
5564 *
5565 * Arguments: info pointer to device instance data
5566 * Return Value: None
5567 */
5568static void usc_reset( struct mgsl_struct *info )
5569{
5570 int i;
5571 u32 readval;
5572
5573 /* Set BIT30 of Misc Control Register */
5574 /* (Local Control Register 0x50) to force reset of USC. */
5575
5576 volatile u32 *MiscCtrl = (u32 *)(info->lcr_base + 0x50);
5577 u32 *LCR0BRDR = (u32 *)(info->lcr_base + 0x28);
5578
5579 info->misc_ctrl_value |= BIT30;
5580 *MiscCtrl = info->misc_ctrl_value;
5581
5582 /*
5583 * Force at least 170ns delay before clearing reset bit. Each read from
5584 * LCR takes at least 30ns so 10 times for 300ns to be safe.
5585 */
5586 for(i=0;i<10;i++)
5587 readval = *MiscCtrl;
5588
5589 info->misc_ctrl_value &= ~BIT30;
5590 *MiscCtrl = info->misc_ctrl_value;
5591
5592 *LCR0BRDR = BUS_DESCRIPTOR(
5593 1, // Write Strobe Hold (0-3)
5594 2, // Write Strobe Delay (0-3)
5595 2, // Read Strobe Delay (0-3)
5596 0, // NWDD (Write data-data) (0-3)
5597 4, // NWAD (Write Addr-data) (0-31)
5598 0, // NXDA (Read/Write Data-Addr) (0-3)
5599 0, // NRDD (Read Data-Data) (0-3)
5600 5 // NRAD (Read Addr-Data) (0-31)
5601 );
5602
5603 info->mbre_bit = 0;
5604 info->loopback_bits = 0;
5605 info->usc_idle_mode = 0;
5606
5607 /*
5608 * Program the Bus Configuration Register (BCR)
5609 *
5610 * <15> 0 Don't use separate address
5611 * <14..6> 0 reserved
5612 * <5..4> 00 IAckmode = Default, don't care
5613 * <3> 1 Bus Request Totem Pole output
5614 * <2> 1 Use 16 Bit data bus
5615 * <1> 0 IRQ Totem Pole output
5616 * <0> 0 Don't Shift Right Addr
5617 *
5618 * 0000 0000 0000 1100 = 0x000c
5619 *
5620 * By writing to io_base + SDPIN the Wait/Ack pin is
5621 * programmed to work as a Wait pin.
5622 */
5623
5624 outw( 0x000c,info->io_base + SDPIN );
5625
5626
5627 outw( 0,info->io_base );
5628 outw( 0,info->io_base + CCAR );
5629
5630 /* select little endian byte ordering */
5631 usc_RTCmd( info, RTCmd_SelectLittleEndian );
5632
5633
5634 /* Port Control Register (PCR)
5635 *
5636 * <15..14> 11 Port 7 is Output (~DMAEN, Bit 14 : 0 = Enabled)
5637 * <13..12> 11 Port 6 is Output (~INTEN, Bit 12 : 0 = Enabled)
5638 * <11..10> 00 Port 5 is Input (No Connect, Don't Care)
5639 * <9..8> 00 Port 4 is Input (No Connect, Don't Care)
5640 * <7..6> 11 Port 3 is Output (~RTS, Bit 6 : 0 = Enabled )
5641 * <5..4> 11 Port 2 is Output (~DTR, Bit 4 : 0 = Enabled )
5642 * <3..2> 01 Port 1 is Input (Dedicated RxC)
5643 * <1..0> 01 Port 0 is Input (Dedicated TxC)
5644 *
5645 * 1111 0000 1111 0101 = 0xf0f5
5646 */
5647
5648 usc_OutReg( info, PCR, 0xf0f5 );
5649
5650
5651 /*
5652 * Input/Output Control Register
5653 *
5654 * <15..14> 00 CTS is active low input
5655 * <13..12> 00 DCD is active low input
5656 * <11..10> 00 TxREQ pin is input (DSR)
5657 * <9..8> 00 RxREQ pin is input (RI)
5658 * <7..6> 00 TxD is output (Transmit Data)
5659 * <5..3> 000 TxC Pin in Input (14.7456MHz Clock)
5660 * <2..0> 100 RxC is Output (drive with BRG0)
5661 *
5662 * 0000 0000 0000 0100 = 0x0004
5663 */
5664
5665 usc_OutReg( info, IOCR, 0x0004 );
5666
5667} /* end of usc_reset() */
5668
5669/* usc_set_async_mode()
5670 *
5671 * Program adapter for asynchronous communications.
5672 *
5673 * Arguments: info pointer to device instance data
5674 * Return Value: None
5675 */
5676static void usc_set_async_mode( struct mgsl_struct *info )
5677{
5678 u16 RegValue;
5679
5680 /* disable interrupts while programming USC */
5681 usc_DisableMasterIrqBit( info );
5682
5683 outw( 0, info->io_base ); /* clear Master Bus Enable (DCAR) */
5684 usc_DmaCmd( info, DmaCmd_ResetAllChannels ); /* disable both DMA channels */
5685
5686 usc_loopback_frame( info );
5687
5688 /* Channel mode Register (CMR)
5689 *
5690 * <15..14> 00 Tx Sub modes, 00 = 1 Stop Bit
5691 * <13..12> 00 00 = 16X Clock
5692 * <11..8> 0000 Transmitter mode = Asynchronous
5693 * <7..6> 00 reserved?
5694 * <5..4> 00 Rx Sub modes, 00 = 16X Clock
5695 * <3..0> 0000 Receiver mode = Asynchronous
5696 *
5697 * 0000 0000 0000 0000 = 0x0
5698 */
5699
5700 RegValue = 0;
5701 if ( info->params.stop_bits != 1 )
5702 RegValue |= BIT14;
5703 usc_OutReg( info, CMR, RegValue );
5704
5705
5706 /* Receiver mode Register (RMR)
5707 *
5708 * <15..13> 000 encoding = None
5709 * <12..08> 00000 reserved (Sync Only)
5710 * <7..6> 00 Even parity
5711 * <5> 0 parity disabled
5712 * <4..2> 000 Receive Char Length = 8 bits
5713 * <1..0> 00 Disable Receiver
5714 *
5715 * 0000 0000 0000 0000 = 0x0
5716 */
5717
5718 RegValue = 0;
5719
5720 if ( info->params.data_bits != 8 )
5721 RegValue |= BIT4 | BIT3 | BIT2;
5722
5723 if ( info->params.parity != ASYNC_PARITY_NONE ) {
5724 RegValue |= BIT5;
5725 if ( info->params.parity != ASYNC_PARITY_ODD )
5726 RegValue |= BIT6;
5727 }
5728
5729 usc_OutReg( info, RMR, RegValue );
5730
5731
5732 /* Set IRQ trigger level */
5733
5734 usc_RCmd( info, RCmd_SelectRicrIntLevel );
5735
5736
5737 /* Receive Interrupt Control Register (RICR)
5738 *
5739 * <15..8> ? RxFIFO IRQ Request Level
5740 *
5741 * Note: For async mode the receive FIFO level must be set
5742 * to 0 to avoid the situation where the FIFO contains fewer bytes
5743 * than the trigger level and no more data is expected.
5744 *
5745 * <7> 0 Exited Hunt IA (Interrupt Arm)
5746 * <6> 0 Idle Received IA
5747 * <5> 0 Break/Abort IA
5748 * <4> 0 Rx Bound IA
5749 * <3> 0 Queued status reflects oldest byte in FIFO
5750 * <2> 0 Abort/PE IA
5751 * <1> 0 Rx Overrun IA
5752 * <0> 0 Select TC0 value for readback
5753 *
5754 * 0000 0000 0100 0000 = 0x0000 + (FIFOLEVEL in MSB)
5755 */
5756
5757 usc_OutReg( info, RICR, 0x0000 );
5758
5759 usc_UnlatchRxstatusBits( info, RXSTATUS_ALL );
5760 usc_ClearIrqPendingBits( info, RECEIVE_STATUS );
5761
5762
5763 /* Transmit mode Register (TMR)
5764 *
5765 * <15..13> 000 encoding = None
5766 * <12..08> 00000 reserved (Sync Only)
5767 * <7..6> 00 Transmit parity Even
5768 * <5> 0 Transmit parity Disabled
5769 * <4..2> 000 Tx Char Length = 8 bits
5770 * <1..0> 00 Disable Transmitter
5771 *
5772 * 0000 0000 0000 0000 = 0x0
5773 */
5774
5775 RegValue = 0;
5776
5777 if ( info->params.data_bits != 8 )
5778 RegValue |= BIT4 | BIT3 | BIT2;
5779
5780 if ( info->params.parity != ASYNC_PARITY_NONE ) {
5781 RegValue |= BIT5;
5782 if ( info->params.parity != ASYNC_PARITY_ODD )
5783 RegValue |= BIT6;
5784 }
5785
5786 usc_OutReg( info, TMR, RegValue );
5787
5788 usc_set_txidle( info );
5789
5790
5791 /* Set IRQ trigger level */
5792
5793 usc_TCmd( info, TCmd_SelectTicrIntLevel );
5794
5795
5796 /* Transmit Interrupt Control Register (TICR)
5797 *
5798 * <15..8> ? Transmit FIFO IRQ Level
5799 * <7> 0 Present IA (Interrupt Arm)
5800 * <6> 1 Idle Sent IA
5801 * <5> 0 Abort Sent IA
5802 * <4> 0 EOF/EOM Sent IA
5803 * <3> 0 CRC Sent IA
5804 * <2> 0 1 = Wait for SW Trigger to Start Frame
5805 * <1> 0 Tx Underrun IA
5806 * <0> 0 TC0 constant on read back
5807 *
5808 * 0000 0000 0100 0000 = 0x0040
5809 */
5810
5811 usc_OutReg( info, TICR, 0x1f40 );
5812
5813 usc_UnlatchTxstatusBits( info, TXSTATUS_ALL );
5814 usc_ClearIrqPendingBits( info, TRANSMIT_STATUS );
5815
5816 usc_enable_async_clock( info, info->params.data_rate );
5817
5818
5819 /* Channel Control/status Register (CCSR)
5820 *
5821 * <15> X RCC FIFO Overflow status (RO)
5822 * <14> X RCC FIFO Not Empty status (RO)
5823 * <13> 0 1 = Clear RCC FIFO (WO)
5824 * <12> X DPLL in Sync status (RO)
5825 * <11> X DPLL 2 Missed Clocks status (RO)
5826 * <10> X DPLL 1 Missed Clock status (RO)
5827 * <9..8> 00 DPLL Resync on rising and falling edges (RW)
5828 * <7> X SDLC Loop On status (RO)
5829 * <6> X SDLC Loop Send status (RO)
5830 * <5> 1 Bypass counters for TxClk and RxClk (RW)
5831 * <4..2> 000 Last Char of SDLC frame has 8 bits (RW)
5832 * <1..0> 00 reserved
5833 *
5834 * 0000 0000 0010 0000 = 0x0020
5835 */
5836
5837 usc_OutReg( info, CCSR, 0x0020 );
5838
5839 usc_DisableInterrupts( info, TRANSMIT_STATUS + TRANSMIT_DATA +
5840 RECEIVE_DATA + RECEIVE_STATUS );
5841
5842 usc_ClearIrqPendingBits( info, TRANSMIT_STATUS + TRANSMIT_DATA +
5843 RECEIVE_DATA + RECEIVE_STATUS );
5844
5845 usc_EnableMasterIrqBit( info );
5846
5847 if (info->params.loopback) {
5848 info->loopback_bits = 0x300;
5849 outw(0x0300, info->io_base + CCAR);
5850 }
5851
5852} /* end of usc_set_async_mode() */
5853
5854/* usc_loopback_frame()
5855 *
5856 * Loop back a small (2 byte) dummy SDLC frame.
5857 * Interrupts and DMA are NOT used. The purpose of this is to
5858 * clear any 'stale' status info left over from running in async mode.
5859 *
5860 * The 16C32 shows the strange behaviour of marking the 1st
5861 * received SDLC frame with a CRC error even when there is no
5862 * CRC error. To get around this a small dummy from of 2 bytes
5863 * is looped back when switching from async to sync mode.
5864 *
5865 * Arguments: info pointer to device instance data
5866 * Return Value: None
5867 */
5868static void usc_loopback_frame( struct mgsl_struct *info )
5869{
5870 int i;
5871 unsigned long oldmode = info->params.mode;
5872
5873 info->params.mode = MGSL_MODE_HDLC;
5874
5875 usc_DisableMasterIrqBit( info );
5876
5877 usc_set_sdlc_mode( info );
5878 usc_enable_loopback( info, 1 );
5879
5880 /* Write 16-bit Time Constant for BRG0 */
5881 usc_OutReg( info, TC0R, 0 );
5882
5883 /* Channel Control Register (CCR)
5884 *
5885 * <15..14> 00 Don't use 32-bit Tx Control Blocks (TCBs)
5886 * <13> 0 Trigger Tx on SW Command Disabled
5887 * <12> 0 Flag Preamble Disabled
5888 * <11..10> 00 Preamble Length = 8-Bits
5889 * <9..8> 01 Preamble Pattern = flags
5890 * <7..6> 10 Don't use 32-bit Rx status Blocks (RSBs)
5891 * <5> 0 Trigger Rx on SW Command Disabled
5892 * <4..0> 0 reserved
5893 *
5894 * 0000 0001 0000 0000 = 0x0100
5895 */
5896
5897 usc_OutReg( info, CCR, 0x0100 );
5898
5899 /* SETUP RECEIVER */
5900 usc_RTCmd( info, RTCmd_PurgeRxFifo );
5901 usc_EnableReceiver(info,ENABLE_UNCONDITIONAL);
5902
5903 /* SETUP TRANSMITTER */
5904 /* Program the Transmit Character Length Register (TCLR) */
5905 /* and clear FIFO (TCC is loaded with TCLR on FIFO clear) */
5906 usc_OutReg( info, TCLR, 2 );
5907 usc_RTCmd( info, RTCmd_PurgeTxFifo );
5908
5909 /* unlatch Tx status bits, and start transmit channel. */
5910 usc_UnlatchTxstatusBits(info,TXSTATUS_ALL);
5911 outw(0,info->io_base + DATAREG);
5912
5913 /* ENABLE TRANSMITTER */
5914 usc_TCmd( info, TCmd_SendFrame );
5915 usc_EnableTransmitter(info,ENABLE_UNCONDITIONAL);
5916
5917 /* WAIT FOR RECEIVE COMPLETE */
5918 for (i=0 ; i<1000 ; i++)
5919 if (usc_InReg( info, RCSR ) & (BIT8 | BIT4 | BIT3 | BIT1))
5920 break;
5921
5922 /* clear Internal Data loopback mode */
5923 usc_enable_loopback(info, 0);
5924
5925 usc_EnableMasterIrqBit(info);
5926
5927 info->params.mode = oldmode;
5928
5929} /* end of usc_loopback_frame() */
5930
5931/* usc_set_sync_mode() Programs the USC for SDLC communications.
5932 *
5933 * Arguments: info pointer to adapter info structure
5934 * Return Value: None
5935 */
5936static void usc_set_sync_mode( struct mgsl_struct *info )
5937{
5938 usc_loopback_frame( info );
5939 usc_set_sdlc_mode( info );
5940
5941 usc_enable_aux_clock(info, info->params.clock_speed);
5942
5943 if (info->params.loopback)
5944 usc_enable_loopback(info,1);
5945
5946} /* end of mgsl_set_sync_mode() */
5947
5948/* usc_set_txidle() Set the HDLC idle mode for the transmitter.
5949 *
5950 * Arguments: info pointer to device instance data
5951 * Return Value: None
5952 */
5953static void usc_set_txidle( struct mgsl_struct *info )
5954{
5955 u16 usc_idle_mode = IDLEMODE_FLAGS;
5956
5957 /* Map API idle mode to USC register bits */
5958
5959 switch( info->idle_mode ){
5960 case HDLC_TXIDLE_FLAGS: usc_idle_mode = IDLEMODE_FLAGS; break;
5961 case HDLC_TXIDLE_ALT_ZEROS_ONES: usc_idle_mode = IDLEMODE_ALT_ONE_ZERO; break;
5962 case HDLC_TXIDLE_ZEROS: usc_idle_mode = IDLEMODE_ZERO; break;
5963 case HDLC_TXIDLE_ONES: usc_idle_mode = IDLEMODE_ONE; break;
5964 case HDLC_TXIDLE_ALT_MARK_SPACE: usc_idle_mode = IDLEMODE_ALT_MARK_SPACE; break;
5965 case HDLC_TXIDLE_SPACE: usc_idle_mode = IDLEMODE_SPACE; break;
5966 case HDLC_TXIDLE_MARK: usc_idle_mode = IDLEMODE_MARK; break;
5967 }
5968
5969 info->usc_idle_mode = usc_idle_mode;
5970 //usc_OutReg(info, TCSR, usc_idle_mode);
5971 info->tcsr_value &= ~IDLEMODE_MASK; /* clear idle mode bits */
5972 info->tcsr_value += usc_idle_mode;
5973 usc_OutReg(info, TCSR, info->tcsr_value);
5974
5975 /*
5976 * if SyncLink WAN adapter is running in external sync mode, the
5977 * transmitter has been set to Monosync in order to try to mimic
5978 * a true raw outbound bit stream. Monosync still sends an open/close
5979 * sync char at the start/end of a frame. Try to match those sync
5980 * patterns to the idle mode set here
5981 */
5982 if ( info->params.mode == MGSL_MODE_RAW ) {
5983 unsigned char syncpat = 0;
5984 switch( info->idle_mode ) {
5985 case HDLC_TXIDLE_FLAGS:
5986 syncpat = 0x7e;
5987 break;
5988 case HDLC_TXIDLE_ALT_ZEROS_ONES:
5989 syncpat = 0x55;
5990 break;
5991 case HDLC_TXIDLE_ZEROS:
5992 case HDLC_TXIDLE_SPACE:
5993 syncpat = 0x00;
5994 break;
5995 case HDLC_TXIDLE_ONES:
5996 case HDLC_TXIDLE_MARK:
5997 syncpat = 0xff;
5998 break;
5999 case HDLC_TXIDLE_ALT_MARK_SPACE:
6000 syncpat = 0xaa;
6001 break;
6002 }
6003
6004 usc_SetTransmitSyncChars(info,syncpat,syncpat);
6005 }
6006
6007} /* end of usc_set_txidle() */
6008
6009/* usc_get_serial_signals()
6010 *
6011 * Query the adapter for the state of the V24 status (input) signals.
6012 *
6013 * Arguments: info pointer to device instance data
6014 * Return Value: None
6015 */
6016static void usc_get_serial_signals( struct mgsl_struct *info )
6017{
6018 u16 status;
6019
6020 /* clear all serial signals except RTS and DTR */
6021 info->serial_signals &= SerialSignal_RTS | SerialSignal_DTR;
6022
6023 /* Read the Misc Interrupt status Register (MISR) to get */
6024 /* the V24 status signals. */
6025
6026 status = usc_InReg( info, MISR );
6027
6028 /* set serial signal bits to reflect MISR */
6029
6030 if ( status & MISCSTATUS_CTS )
6031 info->serial_signals |= SerialSignal_CTS;
6032
6033 if ( status & MISCSTATUS_DCD )
6034 info->serial_signals |= SerialSignal_DCD;
6035
6036 if ( status & MISCSTATUS_RI )
6037 info->serial_signals |= SerialSignal_RI;
6038
6039 if ( status & MISCSTATUS_DSR )
6040 info->serial_signals |= SerialSignal_DSR;
6041
6042} /* end of usc_get_serial_signals() */
6043
6044/* usc_set_serial_signals()
6045 *
6046 * Set the state of RTS and DTR based on contents of
6047 * serial_signals member of device extension.
6048 *
6049 * Arguments: info pointer to device instance data
6050 * Return Value: None
6051 */
6052static void usc_set_serial_signals( struct mgsl_struct *info )
6053{
6054 u16 Control;
6055 unsigned char V24Out = info->serial_signals;
6056
6057 /* get the current value of the Port Control Register (PCR) */
6058
6059 Control = usc_InReg( info, PCR );
6060
6061 if ( V24Out & SerialSignal_RTS )
6062 Control &= ~(BIT6);
6063 else
6064 Control |= BIT6;
6065
6066 if ( V24Out & SerialSignal_DTR )
6067 Control &= ~(BIT4);
6068 else
6069 Control |= BIT4;
6070
6071 usc_OutReg( info, PCR, Control );
6072
6073} /* end of usc_set_serial_signals() */
6074
6075/* usc_enable_async_clock()
6076 *
6077 * Enable the async clock at the specified frequency.
6078 *
6079 * Arguments: info pointer to device instance data
6080 * data_rate data rate of clock in bps
6081 * 0 disables the AUX clock.
6082 * Return Value: None
6083 */
6084static void usc_enable_async_clock( struct mgsl_struct *info, u32 data_rate )
6085{
6086 if ( data_rate ) {
6087 /*
6088 * Clock mode Control Register (CMCR)
6089 *
6090 * <15..14> 00 counter 1 Disabled
6091 * <13..12> 00 counter 0 Disabled
6092 * <11..10> 11 BRG1 Input is TxC Pin
6093 * <9..8> 11 BRG0 Input is TxC Pin
6094 * <7..6> 01 DPLL Input is BRG1 Output
6095 * <5..3> 100 TxCLK comes from BRG0
6096 * <2..0> 100 RxCLK comes from BRG0
6097 *
6098 * 0000 1111 0110 0100 = 0x0f64
6099 */
6100
6101 usc_OutReg( info, CMCR, 0x0f64 );
6102
6103
6104 /*
6105 * Write 16-bit Time Constant for BRG0
6106 * Time Constant = (ClkSpeed / data_rate) - 1
6107 * ClkSpeed = 921600 (ISA), 691200 (PCI)
6108 */
6109
6110 usc_OutReg( info, TC0R, (u16)((691200/data_rate) - 1) );
6111
6112 /*
6113 * Hardware Configuration Register (HCR)
6114 * Clear Bit 1, BRG0 mode = Continuous
6115 * Set Bit 0 to enable BRG0.
6116 */
6117
6118 usc_OutReg( info, HCR,
6119 (u16)((usc_InReg( info, HCR ) & ~BIT1) | BIT0) );
6120
6121
6122 /* Input/Output Control Reg, <2..0> = 100, Drive RxC pin with BRG0 */
6123
6124 usc_OutReg( info, IOCR,
6125 (u16)((usc_InReg(info, IOCR) & 0xfff8) | 0x0004) );
6126 } else {
6127 /* data rate == 0 so turn off BRG0 */
6128 usc_OutReg( info, HCR, (u16)(usc_InReg( info, HCR ) & ~BIT0) );
6129 }
6130
6131} /* end of usc_enable_async_clock() */
6132
6133/*
6134 * Buffer Structures:
6135 *
6136 * Normal memory access uses virtual addresses that can make discontiguous
6137 * physical memory pages appear to be contiguous in the virtual address
6138 * space (the processors memory mapping handles the conversions).
6139 *
6140 * DMA transfers require physically contiguous memory. This is because
6141 * the DMA system controller and DMA bus masters deal with memory using
6142 * only physical addresses.
6143 *
6144 * This causes a problem under Windows NT when large DMA buffers are
6145 * needed. Fragmentation of the nonpaged pool prevents allocations of
6146 * physically contiguous buffers larger than the PAGE_SIZE.
6147 *
6148 * However the 16C32 supports Bus Master Scatter/Gather DMA which
6149 * allows DMA transfers to physically discontiguous buffers. Information
6150 * about each data transfer buffer is contained in a memory structure
6151 * called a 'buffer entry'. A list of buffer entries is maintained
6152 * to track and control the use of the data transfer buffers.
6153 *
6154 * To support this strategy we will allocate sufficient PAGE_SIZE
6155 * contiguous memory buffers to allow for the total required buffer
6156 * space.
6157 *
6158 * The 16C32 accesses the list of buffer entries using Bus Master
6159 * DMA. Control information is read from the buffer entries by the
6160 * 16C32 to control data transfers. status information is written to
6161 * the buffer entries by the 16C32 to indicate the status of completed
6162 * transfers.
6163 *
6164 * The CPU writes control information to the buffer entries to control
6165 * the 16C32 and reads status information from the buffer entries to
6166 * determine information about received and transmitted frames.
6167 *
6168 * Because the CPU and 16C32 (adapter) both need simultaneous access
6169 * to the buffer entries, the buffer entry memory is allocated with
6170 * HalAllocateCommonBuffer(). This restricts the size of the buffer
6171 * entry list to PAGE_SIZE.
6172 *
6173 * The actual data buffers on the other hand will only be accessed
6174 * by the CPU or the adapter but not by both simultaneously. This allows
6175 * Scatter/Gather packet based DMA procedures for using physically
6176 * discontiguous pages.
6177 */
6178
6179/*
6180 * mgsl_reset_tx_dma_buffers()
6181 *
6182 * Set the count for all transmit buffers to 0 to indicate the
6183 * buffer is available for use and set the current buffer to the
6184 * first buffer. This effectively makes all buffers free and
6185 * discards any data in buffers.
6186 *
6187 * Arguments: info pointer to device instance data
6188 * Return Value: None
6189 */
6190static void mgsl_reset_tx_dma_buffers( struct mgsl_struct *info )
6191{
6192 unsigned int i;
6193
6194 for ( i = 0; i < info->tx_buffer_count; i++ ) {
6195 *((unsigned long *)&(info->tx_buffer_list[i].count)) = 0;
6196 }
6197
6198 info->current_tx_buffer = 0;
6199 info->start_tx_dma_buffer = 0;
6200 info->tx_dma_buffers_used = 0;
6201
6202 info->get_tx_holding_index = 0;
6203 info->put_tx_holding_index = 0;
6204 info->tx_holding_count = 0;
6205
6206} /* end of mgsl_reset_tx_dma_buffers() */
6207
6208/*
6209 * num_free_tx_dma_buffers()
6210 *
6211 * returns the number of free tx dma buffers available
6212 *
6213 * Arguments: info pointer to device instance data
6214 * Return Value: number of free tx dma buffers
6215 */
6216static int num_free_tx_dma_buffers(struct mgsl_struct *info)
6217{
6218 return info->tx_buffer_count - info->tx_dma_buffers_used;
6219}
6220
6221/*
6222 * mgsl_reset_rx_dma_buffers()
6223 *
6224 * Set the count for all receive buffers to DMABUFFERSIZE
6225 * and set the current buffer to the first buffer. This effectively
6226 * makes all buffers free and discards any data in buffers.
6227 *
6228 * Arguments: info pointer to device instance data
6229 * Return Value: None
6230 */
6231static void mgsl_reset_rx_dma_buffers( struct mgsl_struct *info )
6232{
6233 unsigned int i;
6234
6235 for ( i = 0; i < info->rx_buffer_count; i++ ) {
6236 *((unsigned long *)&(info->rx_buffer_list[i].count)) = DMABUFFERSIZE;
6237// info->rx_buffer_list[i].count = DMABUFFERSIZE;
6238// info->rx_buffer_list[i].status = 0;
6239 }
6240
6241 info->current_rx_buffer = 0;
6242
6243} /* end of mgsl_reset_rx_dma_buffers() */
6244
6245/*
6246 * mgsl_free_rx_frame_buffers()
6247 *
6248 * Free the receive buffers used by a received SDLC
6249 * frame such that the buffers can be reused.
6250 *
6251 * Arguments:
6252 *
6253 * info pointer to device instance data
6254 * StartIndex index of 1st receive buffer of frame
6255 * EndIndex index of last receive buffer of frame
6256 *
6257 * Return Value: None
6258 */
6259static void mgsl_free_rx_frame_buffers( struct mgsl_struct *info, unsigned int StartIndex, unsigned int EndIndex )
6260{
6261 bool Done = false;
6262 DMABUFFERENTRY *pBufEntry;
6263 unsigned int Index;
6264
6265 /* Starting with 1st buffer entry of the frame clear the status */
6266 /* field and set the count field to DMA Buffer Size. */
6267
6268 Index = StartIndex;
6269
6270 while( !Done ) {
6271 pBufEntry = &(info->rx_buffer_list[Index]);
6272
6273 if ( Index == EndIndex ) {
6274 /* This is the last buffer of the frame! */
6275 Done = true;
6276 }
6277
6278 /* reset current buffer for reuse */
6279// pBufEntry->status = 0;
6280// pBufEntry->count = DMABUFFERSIZE;
6281 *((unsigned long *)&(pBufEntry->count)) = DMABUFFERSIZE;
6282
6283 /* advance to next buffer entry in linked list */
6284 Index++;
6285 if ( Index == info->rx_buffer_count )
6286 Index = 0;
6287 }
6288
6289 /* set current buffer to next buffer after last buffer of frame */
6290 info->current_rx_buffer = Index;
6291
6292} /* end of free_rx_frame_buffers() */
6293
6294/* mgsl_get_rx_frame()
6295 *
6296 * This function attempts to return a received SDLC frame from the
6297 * receive DMA buffers. Only frames received without errors are returned.
6298 *
6299 * Arguments: info pointer to device extension
6300 * Return Value: true if frame returned, otherwise false
6301 */
6302static bool mgsl_get_rx_frame(struct mgsl_struct *info)
6303{
6304 unsigned int StartIndex, EndIndex; /* index of 1st and last buffers of Rx frame */
6305 unsigned short status;
6306 DMABUFFERENTRY *pBufEntry;
6307 unsigned int framesize = 0;
6308 bool ReturnCode = false;
6309 unsigned long flags;
6310 struct tty_struct *tty = info->port.tty;
6311 bool return_frame = false;
6312
6313 /*
6314 * current_rx_buffer points to the 1st buffer of the next available
6315 * receive frame. To find the last buffer of the frame look for
6316 * a non-zero status field in the buffer entries. (The status
6317 * field is set by the 16C32 after completing a receive frame.
6318 */
6319
6320 StartIndex = EndIndex = info->current_rx_buffer;
6321
6322 while( !info->rx_buffer_list[EndIndex].status ) {
6323 /*
6324 * If the count field of the buffer entry is non-zero then
6325 * this buffer has not been used. (The 16C32 clears the count
6326 * field when it starts using the buffer.) If an unused buffer
6327 * is encountered then there are no frames available.
6328 */
6329
6330 if ( info->rx_buffer_list[EndIndex].count )
6331 goto Cleanup;
6332
6333 /* advance to next buffer entry in linked list */
6334 EndIndex++;
6335 if ( EndIndex == info->rx_buffer_count )
6336 EndIndex = 0;
6337
6338 /* if entire list searched then no frame available */
6339 if ( EndIndex == StartIndex ) {
6340 /* If this occurs then something bad happened,
6341 * all buffers have been 'used' but none mark
6342 * the end of a frame. Reset buffers and receiver.
6343 */
6344
6345 if ( info->rx_enabled ){
6346 spin_lock_irqsave(&info->irq_spinlock,flags);
6347 usc_start_receiver(info);
6348 spin_unlock_irqrestore(&info->irq_spinlock,flags);
6349 }
6350 goto Cleanup;
6351 }
6352 }
6353
6354
6355 /* check status of receive frame */
6356
6357 status = info->rx_buffer_list[EndIndex].status;
6358
6359 if ( status & (RXSTATUS_SHORT_FRAME | RXSTATUS_OVERRUN |
6360 RXSTATUS_CRC_ERROR | RXSTATUS_ABORT) ) {
6361 if ( status & RXSTATUS_SHORT_FRAME )
6362 info->icount.rxshort++;
6363 else if ( status & RXSTATUS_ABORT )
6364 info->icount.rxabort++;
6365 else if ( status & RXSTATUS_OVERRUN )
6366 info->icount.rxover++;
6367 else {
6368 info->icount.rxcrc++;
6369 if ( info->params.crc_type & HDLC_CRC_RETURN_EX )
6370 return_frame = true;
6371 }
6372 framesize = 0;
6373#if SYNCLINK_GENERIC_HDLC
6374 {
6375 info->netdev->stats.rx_errors++;
6376 info->netdev->stats.rx_frame_errors++;
6377 }
6378#endif
6379 } else
6380 return_frame = true;
6381
6382 if ( return_frame ) {
6383 /* receive frame has no errors, get frame size.
6384 * The frame size is the starting value of the RCC (which was
6385 * set to 0xffff) minus the ending value of the RCC (decremented
6386 * once for each receive character) minus 2 for the 16-bit CRC.
6387 */
6388
6389 framesize = RCLRVALUE - info->rx_buffer_list[EndIndex].rcc;
6390
6391 /* adjust frame size for CRC if any */
6392 if ( info->params.crc_type == HDLC_CRC_16_CCITT )
6393 framesize -= 2;
6394 else if ( info->params.crc_type == HDLC_CRC_32_CCITT )
6395 framesize -= 4;
6396 }
6397
6398 if ( debug_level >= DEBUG_LEVEL_BH )
6399 printk("%s(%d):mgsl_get_rx_frame(%s) status=%04X size=%d\n",
6400 __FILE__,__LINE__,info->device_name,status,framesize);
6401
6402 if ( debug_level >= DEBUG_LEVEL_DATA )
6403 mgsl_trace_block(info,info->rx_buffer_list[StartIndex].virt_addr,
6404 min_t(int, framesize, DMABUFFERSIZE),0);
6405
6406 if (framesize) {
6407 if ( ( (info->params.crc_type & HDLC_CRC_RETURN_EX) &&
6408 ((framesize+1) > info->max_frame_size) ) ||
6409 (framesize > info->max_frame_size) )
6410 info->icount.rxlong++;
6411 else {
6412 /* copy dma buffer(s) to contiguous intermediate buffer */
6413 int copy_count = framesize;
6414 int index = StartIndex;
6415 unsigned char *ptmp = info->intermediate_rxbuffer;
6416
6417 if ( !(status & RXSTATUS_CRC_ERROR))
6418 info->icount.rxok++;
6419
6420 while(copy_count) {
6421 int partial_count;
6422 if ( copy_count > DMABUFFERSIZE )
6423 partial_count = DMABUFFERSIZE;
6424 else
6425 partial_count = copy_count;
6426
6427 pBufEntry = &(info->rx_buffer_list[index]);
6428 memcpy( ptmp, pBufEntry->virt_addr, partial_count );
6429 ptmp += partial_count;
6430 copy_count -= partial_count;
6431
6432 if ( ++index == info->rx_buffer_count )
6433 index = 0;
6434 }
6435
6436 if ( info->params.crc_type & HDLC_CRC_RETURN_EX ) {
6437 ++framesize;
6438 *ptmp = (status & RXSTATUS_CRC_ERROR ?
6439 RX_CRC_ERROR :
6440 RX_OK);
6441
6442 if ( debug_level >= DEBUG_LEVEL_DATA )
6443 printk("%s(%d):mgsl_get_rx_frame(%s) rx frame status=%d\n",
6444 __FILE__,__LINE__,info->device_name,
6445 *ptmp);
6446 }
6447
6448#if SYNCLINK_GENERIC_HDLC
6449 if (info->netcount)
6450 hdlcdev_rx(info,info->intermediate_rxbuffer,framesize);
6451 else
6452#endif
6453 ldisc_receive_buf(tty, info->intermediate_rxbuffer, info->flag_buf, framesize);
6454 }
6455 }
6456 /* Free the buffers used by this frame. */
6457 mgsl_free_rx_frame_buffers( info, StartIndex, EndIndex );
6458
6459 ReturnCode = true;
6460
6461Cleanup:
6462
6463 if ( info->rx_enabled && info->rx_overflow ) {
6464 /* The receiver needs to restarted because of
6465 * a receive overflow (buffer or FIFO). If the
6466 * receive buffers are now empty, then restart receiver.
6467 */
6468
6469 if ( !info->rx_buffer_list[EndIndex].status &&
6470 info->rx_buffer_list[EndIndex].count ) {
6471 spin_lock_irqsave(&info->irq_spinlock,flags);
6472 usc_start_receiver(info);
6473 spin_unlock_irqrestore(&info->irq_spinlock,flags);
6474 }
6475 }
6476
6477 return ReturnCode;
6478
6479} /* end of mgsl_get_rx_frame() */
6480
6481/* mgsl_get_raw_rx_frame()
6482 *
6483 * This function attempts to return a received frame from the
6484 * receive DMA buffers when running in external loop mode. In this mode,
6485 * we will return at most one DMABUFFERSIZE frame to the application.
6486 * The USC receiver is triggering off of DCD going active to start a new
6487 * frame, and DCD going inactive to terminate the frame (similar to
6488 * processing a closing flag character).
6489 *
6490 * In this routine, we will return DMABUFFERSIZE "chunks" at a time.
6491 * If DCD goes inactive, the last Rx DMA Buffer will have a non-zero
6492 * status field and the RCC field will indicate the length of the
6493 * entire received frame. We take this RCC field and get the modulus
6494 * of RCC and DMABUFFERSIZE to determine if number of bytes in the
6495 * last Rx DMA buffer and return that last portion of the frame.
6496 *
6497 * Arguments: info pointer to device extension
6498 * Return Value: true if frame returned, otherwise false
6499 */
6500static bool mgsl_get_raw_rx_frame(struct mgsl_struct *info)
6501{
6502 unsigned int CurrentIndex, NextIndex;
6503 unsigned short status;
6504 DMABUFFERENTRY *pBufEntry;
6505 unsigned int framesize = 0;
6506 bool ReturnCode = false;
6507 unsigned long flags;
6508 struct tty_struct *tty = info->port.tty;
6509
6510 /*
6511 * current_rx_buffer points to the 1st buffer of the next available
6512 * receive frame. The status field is set by the 16C32 after
6513 * completing a receive frame. If the status field of this buffer
6514 * is zero, either the USC is still filling this buffer or this
6515 * is one of a series of buffers making up a received frame.
6516 *
6517 * If the count field of this buffer is zero, the USC is either
6518 * using this buffer or has used this buffer. Look at the count
6519 * field of the next buffer. If that next buffer's count is
6520 * non-zero, the USC is still actively using the current buffer.
6521 * Otherwise, if the next buffer's count field is zero, the
6522 * current buffer is complete and the USC is using the next
6523 * buffer.
6524 */
6525 CurrentIndex = NextIndex = info->current_rx_buffer;
6526 ++NextIndex;
6527 if ( NextIndex == info->rx_buffer_count )
6528 NextIndex = 0;
6529
6530 if ( info->rx_buffer_list[CurrentIndex].status != 0 ||
6531 (info->rx_buffer_list[CurrentIndex].count == 0 &&
6532 info->rx_buffer_list[NextIndex].count == 0)) {
6533 /*
6534 * Either the status field of this dma buffer is non-zero
6535 * (indicating the last buffer of a receive frame) or the next
6536 * buffer is marked as in use -- implying this buffer is complete
6537 * and an intermediate buffer for this received frame.
6538 */
6539
6540 status = info->rx_buffer_list[CurrentIndex].status;
6541
6542 if ( status & (RXSTATUS_SHORT_FRAME | RXSTATUS_OVERRUN |
6543 RXSTATUS_CRC_ERROR | RXSTATUS_ABORT) ) {
6544 if ( status & RXSTATUS_SHORT_FRAME )
6545 info->icount.rxshort++;
6546 else if ( status & RXSTATUS_ABORT )
6547 info->icount.rxabort++;
6548 else if ( status & RXSTATUS_OVERRUN )
6549 info->icount.rxover++;
6550 else
6551 info->icount.rxcrc++;
6552 framesize = 0;
6553 } else {
6554 /*
6555 * A receive frame is available, get frame size and status.
6556 *
6557 * The frame size is the starting value of the RCC (which was
6558 * set to 0xffff) minus the ending value of the RCC (decremented
6559 * once for each receive character) minus 2 or 4 for the 16-bit
6560 * or 32-bit CRC.
6561 *
6562 * If the status field is zero, this is an intermediate buffer.
6563 * It's size is 4K.
6564 *
6565 * If the DMA Buffer Entry's Status field is non-zero, the
6566 * receive operation completed normally (ie: DCD dropped). The
6567 * RCC field is valid and holds the received frame size.
6568 * It is possible that the RCC field will be zero on a DMA buffer
6569 * entry with a non-zero status. This can occur if the total
6570 * frame size (number of bytes between the time DCD goes active
6571 * to the time DCD goes inactive) exceeds 65535 bytes. In this
6572 * case the 16C32 has underrun on the RCC count and appears to
6573 * stop updating this counter to let us know the actual received
6574 * frame size. If this happens (non-zero status and zero RCC),
6575 * simply return the entire RxDMA Buffer
6576 */
6577 if ( status ) {
6578 /*
6579 * In the event that the final RxDMA Buffer is
6580 * terminated with a non-zero status and the RCC
6581 * field is zero, we interpret this as the RCC
6582 * having underflowed (received frame > 65535 bytes).
6583 *
6584 * Signal the event to the user by passing back
6585 * a status of RxStatus_CrcError returning the full
6586 * buffer and let the app figure out what data is
6587 * actually valid
6588 */
6589 if ( info->rx_buffer_list[CurrentIndex].rcc )
6590 framesize = RCLRVALUE - info->rx_buffer_list[CurrentIndex].rcc;
6591 else
6592 framesize = DMABUFFERSIZE;
6593 }
6594 else
6595 framesize = DMABUFFERSIZE;
6596 }
6597
6598 if ( framesize > DMABUFFERSIZE ) {
6599 /*
6600 * if running in raw sync mode, ISR handler for
6601 * End Of Buffer events terminates all buffers at 4K.
6602 * If this frame size is said to be >4K, get the
6603 * actual number of bytes of the frame in this buffer.
6604 */
6605 framesize = framesize % DMABUFFERSIZE;
6606 }
6607
6608
6609 if ( debug_level >= DEBUG_LEVEL_BH )
6610 printk("%s(%d):mgsl_get_raw_rx_frame(%s) status=%04X size=%d\n",
6611 __FILE__,__LINE__,info->device_name,status,framesize);
6612
6613 if ( debug_level >= DEBUG_LEVEL_DATA )
6614 mgsl_trace_block(info,info->rx_buffer_list[CurrentIndex].virt_addr,
6615 min_t(int, framesize, DMABUFFERSIZE),0);
6616
6617 if (framesize) {
6618 /* copy dma buffer(s) to contiguous intermediate buffer */
6619 /* NOTE: we never copy more than DMABUFFERSIZE bytes */
6620
6621 pBufEntry = &(info->rx_buffer_list[CurrentIndex]);
6622 memcpy( info->intermediate_rxbuffer, pBufEntry->virt_addr, framesize);
6623 info->icount.rxok++;
6624
6625 ldisc_receive_buf(tty, info->intermediate_rxbuffer, info->flag_buf, framesize);
6626 }
6627
6628 /* Free the buffers used by this frame. */
6629 mgsl_free_rx_frame_buffers( info, CurrentIndex, CurrentIndex );
6630
6631 ReturnCode = true;
6632 }
6633
6634
6635 if ( info->rx_enabled && info->rx_overflow ) {
6636 /* The receiver needs to restarted because of
6637 * a receive overflow (buffer or FIFO). If the
6638 * receive buffers are now empty, then restart receiver.
6639 */
6640
6641 if ( !info->rx_buffer_list[CurrentIndex].status &&
6642 info->rx_buffer_list[CurrentIndex].count ) {
6643 spin_lock_irqsave(&info->irq_spinlock,flags);
6644 usc_start_receiver(info);
6645 spin_unlock_irqrestore(&info->irq_spinlock,flags);
6646 }
6647 }
6648
6649 return ReturnCode;
6650
6651} /* end of mgsl_get_raw_rx_frame() */
6652
6653/* mgsl_load_tx_dma_buffer()
6654 *
6655 * Load the transmit DMA buffer with the specified data.
6656 *
6657 * Arguments:
6658 *
6659 * info pointer to device extension
6660 * Buffer pointer to buffer containing frame to load
6661 * BufferSize size in bytes of frame in Buffer
6662 *
6663 * Return Value: None
6664 */
6665static void mgsl_load_tx_dma_buffer(struct mgsl_struct *info,
6666 const char *Buffer, unsigned int BufferSize)
6667{
6668 unsigned short Copycount;
6669 unsigned int i = 0;
6670 DMABUFFERENTRY *pBufEntry;
6671
6672 if ( debug_level >= DEBUG_LEVEL_DATA )
6673 mgsl_trace_block(info,Buffer, min_t(int, BufferSize, DMABUFFERSIZE), 1);
6674
6675 if (info->params.flags & HDLC_FLAG_HDLC_LOOPMODE) {
6676 /* set CMR:13 to start transmit when
6677 * next GoAhead (abort) is received
6678 */
6679 info->cmr_value |= BIT13;
6680 }
6681
6682 /* begin loading the frame in the next available tx dma
6683 * buffer, remember it's starting location for setting
6684 * up tx dma operation
6685 */
6686 i = info->current_tx_buffer;
6687 info->start_tx_dma_buffer = i;
6688
6689 /* Setup the status and RCC (Frame Size) fields of the 1st */
6690 /* buffer entry in the transmit DMA buffer list. */
6691
6692 info->tx_buffer_list[i].status = info->cmr_value & 0xf000;
6693 info->tx_buffer_list[i].rcc = BufferSize;
6694 info->tx_buffer_list[i].count = BufferSize;
6695
6696 /* Copy frame data from 1st source buffer to the DMA buffers. */
6697 /* The frame data may span multiple DMA buffers. */
6698
6699 while( BufferSize ){
6700 /* Get a pointer to next DMA buffer entry. */
6701 pBufEntry = &info->tx_buffer_list[i++];
6702
6703 if ( i == info->tx_buffer_count )
6704 i=0;
6705
6706 /* Calculate the number of bytes that can be copied from */
6707 /* the source buffer to this DMA buffer. */
6708 if ( BufferSize > DMABUFFERSIZE )
6709 Copycount = DMABUFFERSIZE;
6710 else
6711 Copycount = BufferSize;
6712
6713 /* Actually copy data from source buffer to DMA buffer. */
6714 /* Also set the data count for this individual DMA buffer. */
6715 mgsl_load_pci_memory(pBufEntry->virt_addr, Buffer,Copycount);
6716
6717 pBufEntry->count = Copycount;
6718
6719 /* Advance source pointer and reduce remaining data count. */
6720 Buffer += Copycount;
6721 BufferSize -= Copycount;
6722
6723 ++info->tx_dma_buffers_used;
6724 }
6725
6726 /* remember next available tx dma buffer */
6727 info->current_tx_buffer = i;
6728
6729} /* end of mgsl_load_tx_dma_buffer() */
6730
6731/*
6732 * mgsl_register_test()
6733 *
6734 * Performs a register test of the 16C32.
6735 *
6736 * Arguments: info pointer to device instance data
6737 * Return Value: true if test passed, otherwise false
6738 */
6739static bool mgsl_register_test( struct mgsl_struct *info )
6740{
6741 static unsigned short BitPatterns[] =
6742 { 0x0000, 0xffff, 0xaaaa, 0x5555, 0x1234, 0x6969, 0x9696, 0x0f0f };
6743 static unsigned int Patterncount = ARRAY_SIZE(BitPatterns);
6744 unsigned int i;
6745 bool rc = true;
6746 unsigned long flags;
6747
6748 spin_lock_irqsave(&info->irq_spinlock,flags);
6749 usc_reset(info);
6750
6751 /* Verify the reset state of some registers. */
6752
6753 if ( (usc_InReg( info, SICR ) != 0) ||
6754 (usc_InReg( info, IVR ) != 0) ||
6755 (usc_InDmaReg( info, DIVR ) != 0) ){
6756 rc = false;
6757 }
6758
6759 if ( rc ){
6760 /* Write bit patterns to various registers but do it out of */
6761 /* sync, then read back and verify values. */
6762
6763 for ( i = 0 ; i < Patterncount ; i++ ) {
6764 usc_OutReg( info, TC0R, BitPatterns[i] );
6765 usc_OutReg( info, TC1R, BitPatterns[(i+1)%Patterncount] );
6766 usc_OutReg( info, TCLR, BitPatterns[(i+2)%Patterncount] );
6767 usc_OutReg( info, RCLR, BitPatterns[(i+3)%Patterncount] );
6768 usc_OutReg( info, RSR, BitPatterns[(i+4)%Patterncount] );
6769 usc_OutDmaReg( info, TBCR, BitPatterns[(i+5)%Patterncount] );
6770
6771 if ( (usc_InReg( info, TC0R ) != BitPatterns[i]) ||
6772 (usc_InReg( info, TC1R ) != BitPatterns[(i+1)%Patterncount]) ||
6773 (usc_InReg( info, TCLR ) != BitPatterns[(i+2)%Patterncount]) ||
6774 (usc_InReg( info, RCLR ) != BitPatterns[(i+3)%Patterncount]) ||
6775 (usc_InReg( info, RSR ) != BitPatterns[(i+4)%Patterncount]) ||
6776 (usc_InDmaReg( info, TBCR ) != BitPatterns[(i+5)%Patterncount]) ){
6777 rc = false;
6778 break;
6779 }
6780 }
6781 }
6782
6783 usc_reset(info);
6784 spin_unlock_irqrestore(&info->irq_spinlock,flags);
6785
6786 return rc;
6787
6788} /* end of mgsl_register_test() */
6789
6790/* mgsl_irq_test() Perform interrupt test of the 16C32.
6791 *
6792 * Arguments: info pointer to device instance data
6793 * Return Value: true if test passed, otherwise false
6794 */
6795static bool mgsl_irq_test( struct mgsl_struct *info )
6796{
6797 unsigned long EndTime;
6798 unsigned long flags;
6799
6800 spin_lock_irqsave(&info->irq_spinlock,flags);
6801 usc_reset(info);
6802
6803 /*
6804 * Setup 16C32 to interrupt on TxC pin (14MHz clock) transition.
6805 * The ISR sets irq_occurred to true.
6806 */
6807
6808 info->irq_occurred = false;
6809
6810 /* Enable INTEN gate for ISA adapter (Port 6, Bit12) */
6811 /* Enable INTEN (Port 6, Bit12) */
6812 /* This connects the IRQ request signal to the ISA bus */
6813 /* on the ISA adapter. This has no effect for the PCI adapter */
6814 usc_OutReg( info, PCR, (unsigned short)((usc_InReg(info, PCR) | BIT13) & ~BIT12) );
6815
6816 usc_EnableMasterIrqBit(info);
6817 usc_EnableInterrupts(info, IO_PIN);
6818 usc_ClearIrqPendingBits(info, IO_PIN);
6819
6820 usc_UnlatchIostatusBits(info, MISCSTATUS_TXC_LATCHED);
6821 usc_EnableStatusIrqs(info, SICR_TXC_ACTIVE + SICR_TXC_INACTIVE);
6822
6823 spin_unlock_irqrestore(&info->irq_spinlock,flags);
6824
6825 EndTime=100;
6826 while( EndTime-- && !info->irq_occurred ) {
6827 msleep_interruptible(10);
6828 }
6829
6830 spin_lock_irqsave(&info->irq_spinlock,flags);
6831 usc_reset(info);
6832 spin_unlock_irqrestore(&info->irq_spinlock,flags);
6833
6834 return info->irq_occurred;
6835
6836} /* end of mgsl_irq_test() */
6837
6838/* mgsl_dma_test()
6839 *
6840 * Perform a DMA test of the 16C32. A small frame is
6841 * transmitted via DMA from a transmit buffer to a receive buffer
6842 * using single buffer DMA mode.
6843 *
6844 * Arguments: info pointer to device instance data
6845 * Return Value: true if test passed, otherwise false
6846 */
6847static bool mgsl_dma_test( struct mgsl_struct *info )
6848{
6849 unsigned short FifoLevel;
6850 unsigned long phys_addr;
6851 unsigned int FrameSize;
6852 unsigned int i;
6853 char *TmpPtr;
6854 bool rc = true;
6855 unsigned short status=0;
6856 unsigned long EndTime;
6857 unsigned long flags;
6858 MGSL_PARAMS tmp_params;
6859
6860 /* save current port options */
6861 memcpy(&tmp_params,&info->params,sizeof(MGSL_PARAMS));
6862 /* load default port options */
6863 memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS));
6864
6865#define TESTFRAMESIZE 40
6866
6867 spin_lock_irqsave(&info->irq_spinlock,flags);
6868
6869 /* setup 16C32 for SDLC DMA transfer mode */
6870
6871 usc_reset(info);
6872 usc_set_sdlc_mode(info);
6873 usc_enable_loopback(info,1);
6874
6875 /* Reprogram the RDMR so that the 16C32 does NOT clear the count
6876 * field of the buffer entry after fetching buffer address. This
6877 * way we can detect a DMA failure for a DMA read (which should be
6878 * non-destructive to system memory) before we try and write to
6879 * memory (where a failure could corrupt system memory).
6880 */
6881
6882 /* Receive DMA mode Register (RDMR)
6883 *
6884 * <15..14> 11 DMA mode = Linked List Buffer mode
6885 * <13> 1 RSBinA/L = store Rx status Block in List entry
6886 * <12> 0 1 = Clear count of List Entry after fetching
6887 * <11..10> 00 Address mode = Increment
6888 * <9> 1 Terminate Buffer on RxBound
6889 * <8> 0 Bus Width = 16bits
6890 * <7..0> ? status Bits (write as 0s)
6891 *
6892 * 1110 0010 0000 0000 = 0xe200
6893 */
6894
6895 usc_OutDmaReg( info, RDMR, 0xe200 );
6896
6897 spin_unlock_irqrestore(&info->irq_spinlock,flags);
6898
6899
6900 /* SETUP TRANSMIT AND RECEIVE DMA BUFFERS */
6901
6902 FrameSize = TESTFRAMESIZE;
6903
6904 /* setup 1st transmit buffer entry: */
6905 /* with frame size and transmit control word */
6906
6907 info->tx_buffer_list[0].count = FrameSize;
6908 info->tx_buffer_list[0].rcc = FrameSize;
6909 info->tx_buffer_list[0].status = 0x4000;
6910
6911 /* build a transmit frame in 1st transmit DMA buffer */
6912
6913 TmpPtr = info->tx_buffer_list[0].virt_addr;
6914 for (i = 0; i < FrameSize; i++ )
6915 *TmpPtr++ = i;
6916
6917 /* setup 1st receive buffer entry: */
6918 /* clear status, set max receive buffer size */
6919
6920 info->rx_buffer_list[0].status = 0;
6921 info->rx_buffer_list[0].count = FrameSize + 4;
6922
6923 /* zero out the 1st receive buffer */
6924
6925 memset( info->rx_buffer_list[0].virt_addr, 0, FrameSize + 4 );
6926
6927 /* Set count field of next buffer entries to prevent */
6928 /* 16C32 from using buffers after the 1st one. */
6929
6930 info->tx_buffer_list[1].count = 0;
6931 info->rx_buffer_list[1].count = 0;
6932
6933
6934 /***************************/
6935 /* Program 16C32 receiver. */
6936 /***************************/
6937
6938 spin_lock_irqsave(&info->irq_spinlock,flags);
6939
6940 /* setup DMA transfers */
6941 usc_RTCmd( info, RTCmd_PurgeRxFifo );
6942
6943 /* program 16C32 receiver with physical address of 1st DMA buffer entry */
6944 phys_addr = info->rx_buffer_list[0].phys_entry;
6945 usc_OutDmaReg( info, NRARL, (unsigned short)phys_addr );
6946 usc_OutDmaReg( info, NRARU, (unsigned short)(phys_addr >> 16) );
6947
6948 /* Clear the Rx DMA status bits (read RDMR) and start channel */
6949 usc_InDmaReg( info, RDMR );
6950 usc_DmaCmd( info, DmaCmd_InitRxChannel );
6951
6952 /* Enable Receiver (RMR <1..0> = 10) */
6953 usc_OutReg( info, RMR, (unsigned short)((usc_InReg(info, RMR) & 0xfffc) | 0x0002) );
6954
6955 spin_unlock_irqrestore(&info->irq_spinlock,flags);
6956
6957
6958 /*************************************************************/
6959 /* WAIT FOR RECEIVER TO DMA ALL PARAMETERS FROM BUFFER ENTRY */
6960 /*************************************************************/
6961
6962 /* Wait 100ms for interrupt. */
6963 EndTime = jiffies + msecs_to_jiffies(100);
6964
6965 for(;;) {
6966 if (time_after(jiffies, EndTime)) {
6967 rc = false;
6968 break;
6969 }
6970
6971 spin_lock_irqsave(&info->irq_spinlock,flags);
6972 status = usc_InDmaReg( info, RDMR );
6973 spin_unlock_irqrestore(&info->irq_spinlock,flags);
6974
6975 if ( !(status & BIT4) && (status & BIT5) ) {
6976 /* INITG (BIT 4) is inactive (no entry read in progress) AND */
6977 /* BUSY (BIT 5) is active (channel still active). */
6978 /* This means the buffer entry read has completed. */
6979 break;
6980 }
6981 }
6982
6983
6984 /******************************/
6985 /* Program 16C32 transmitter. */
6986 /******************************/
6987
6988 spin_lock_irqsave(&info->irq_spinlock,flags);
6989
6990 /* Program the Transmit Character Length Register (TCLR) */
6991 /* and clear FIFO (TCC is loaded with TCLR on FIFO clear) */
6992
6993 usc_OutReg( info, TCLR, (unsigned short)info->tx_buffer_list[0].count );
6994 usc_RTCmd( info, RTCmd_PurgeTxFifo );
6995
6996 /* Program the address of the 1st DMA Buffer Entry in linked list */
6997
6998 phys_addr = info->tx_buffer_list[0].phys_entry;
6999 usc_OutDmaReg( info, NTARL, (unsigned short)phys_addr );
7000 usc_OutDmaReg( info, NTARU, (unsigned short)(phys_addr >> 16) );
7001
7002 /* unlatch Tx status bits, and start transmit channel. */
7003
7004 usc_OutReg( info, TCSR, (unsigned short)(( usc_InReg(info, TCSR) & 0x0f00) | 0xfa) );
7005 usc_DmaCmd( info, DmaCmd_InitTxChannel );
7006
7007 /* wait for DMA controller to fill transmit FIFO */
7008
7009 usc_TCmd( info, TCmd_SelectTicrTxFifostatus );
7010
7011 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7012
7013
7014 /**********************************/
7015 /* WAIT FOR TRANSMIT FIFO TO FILL */
7016 /**********************************/
7017
7018 /* Wait 100ms */
7019 EndTime = jiffies + msecs_to_jiffies(100);
7020
7021 for(;;) {
7022 if (time_after(jiffies, EndTime)) {
7023 rc = false;
7024 break;
7025 }
7026
7027 spin_lock_irqsave(&info->irq_spinlock,flags);
7028 FifoLevel = usc_InReg(info, TICR) >> 8;
7029 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7030
7031 if ( FifoLevel < 16 )
7032 break;
7033 else
7034 if ( FrameSize < 32 ) {
7035 /* This frame is smaller than the entire transmit FIFO */
7036 /* so wait for the entire frame to be loaded. */
7037 if ( FifoLevel <= (32 - FrameSize) )
7038 break;
7039 }
7040 }
7041
7042
7043 if ( rc )
7044 {
7045 /* Enable 16C32 transmitter. */
7046
7047 spin_lock_irqsave(&info->irq_spinlock,flags);
7048
7049 /* Transmit mode Register (TMR), <1..0> = 10, Enable Transmitter */
7050 usc_TCmd( info, TCmd_SendFrame );
7051 usc_OutReg( info, TMR, (unsigned short)((usc_InReg(info, TMR) & 0xfffc) | 0x0002) );
7052
7053 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7054
7055
7056 /******************************/
7057 /* WAIT FOR TRANSMIT COMPLETE */
7058 /******************************/
7059
7060 /* Wait 100ms */
7061 EndTime = jiffies + msecs_to_jiffies(100);
7062
7063 /* While timer not expired wait for transmit complete */
7064
7065 spin_lock_irqsave(&info->irq_spinlock,flags);
7066 status = usc_InReg( info, TCSR );
7067 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7068
7069 while ( !(status & (BIT6 | BIT5 | BIT4 | BIT2 | BIT1)) ) {
7070 if (time_after(jiffies, EndTime)) {
7071 rc = false;
7072 break;
7073 }
7074
7075 spin_lock_irqsave(&info->irq_spinlock,flags);
7076 status = usc_InReg( info, TCSR );
7077 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7078 }
7079 }
7080
7081
7082 if ( rc ){
7083 /* CHECK FOR TRANSMIT ERRORS */
7084 if ( status & (BIT5 | BIT1) )
7085 rc = false;
7086 }
7087
7088 if ( rc ) {
7089 /* WAIT FOR RECEIVE COMPLETE */
7090
7091 /* Wait 100ms */
7092 EndTime = jiffies + msecs_to_jiffies(100);
7093
7094 /* Wait for 16C32 to write receive status to buffer entry. */
7095 status=info->rx_buffer_list[0].status;
7096 while ( status == 0 ) {
7097 if (time_after(jiffies, EndTime)) {
7098 rc = false;
7099 break;
7100 }
7101 status=info->rx_buffer_list[0].status;
7102 }
7103 }
7104
7105
7106 if ( rc ) {
7107 /* CHECK FOR RECEIVE ERRORS */
7108 status = info->rx_buffer_list[0].status;
7109
7110 if ( status & (BIT8 | BIT3 | BIT1) ) {
7111 /* receive error has occurred */
7112 rc = false;
7113 } else {
7114 if ( memcmp( info->tx_buffer_list[0].virt_addr ,
7115 info->rx_buffer_list[0].virt_addr, FrameSize ) ){
7116 rc = false;
7117 }
7118 }
7119 }
7120
7121 spin_lock_irqsave(&info->irq_spinlock,flags);
7122 usc_reset( info );
7123 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7124
7125 /* restore current port options */
7126 memcpy(&info->params,&tmp_params,sizeof(MGSL_PARAMS));
7127
7128 return rc;
7129
7130} /* end of mgsl_dma_test() */
7131
7132/* mgsl_adapter_test()
7133 *
7134 * Perform the register, IRQ, and DMA tests for the 16C32.
7135 *
7136 * Arguments: info pointer to device instance data
7137 * Return Value: 0 if success, otherwise -ENODEV
7138 */
7139static int mgsl_adapter_test( struct mgsl_struct *info )
7140{
7141 if ( debug_level >= DEBUG_LEVEL_INFO )
7142 printk( "%s(%d):Testing device %s\n",
7143 __FILE__,__LINE__,info->device_name );
7144
7145 if ( !mgsl_register_test( info ) ) {
7146 info->init_error = DiagStatus_AddressFailure;
7147 printk( "%s(%d):Register test failure for device %s Addr=%04X\n",
7148 __FILE__,__LINE__,info->device_name, (unsigned short)(info->io_base) );
7149 return -ENODEV;
7150 }
7151
7152 if ( !mgsl_irq_test( info ) ) {
7153 info->init_error = DiagStatus_IrqFailure;
7154 printk( "%s(%d):Interrupt test failure for device %s IRQ=%d\n",
7155 __FILE__,__LINE__,info->device_name, (unsigned short)(info->irq_level) );
7156 return -ENODEV;
7157 }
7158
7159 if ( !mgsl_dma_test( info ) ) {
7160 info->init_error = DiagStatus_DmaFailure;
7161 printk( "%s(%d):DMA test failure for device %s DMA=%d\n",
7162 __FILE__,__LINE__,info->device_name, (unsigned short)(info->dma_level) );
7163 return -ENODEV;
7164 }
7165
7166 if ( debug_level >= DEBUG_LEVEL_INFO )
7167 printk( "%s(%d):device %s passed diagnostics\n",
7168 __FILE__,__LINE__,info->device_name );
7169
7170 return 0;
7171
7172} /* end of mgsl_adapter_test() */
7173
7174/* mgsl_memory_test()
7175 *
7176 * Test the shared memory on a PCI adapter.
7177 *
7178 * Arguments: info pointer to device instance data
7179 * Return Value: true if test passed, otherwise false
7180 */
7181static bool mgsl_memory_test( struct mgsl_struct *info )
7182{
7183 static unsigned long BitPatterns[] =
7184 { 0x0, 0x55555555, 0xaaaaaaaa, 0x66666666, 0x99999999, 0xffffffff, 0x12345678 };
7185 unsigned long Patterncount = ARRAY_SIZE(BitPatterns);
7186 unsigned long i;
7187 unsigned long TestLimit = SHARED_MEM_ADDRESS_SIZE/sizeof(unsigned long);
7188 unsigned long * TestAddr;
7189
7190 TestAddr = (unsigned long *)info->memory_base;
7191
7192 /* Test data lines with test pattern at one location. */
7193
7194 for ( i = 0 ; i < Patterncount ; i++ ) {
7195 *TestAddr = BitPatterns[i];
7196 if ( *TestAddr != BitPatterns[i] )
7197 return false;
7198 }
7199
7200 /* Test address lines with incrementing pattern over */
7201 /* entire address range. */
7202
7203 for ( i = 0 ; i < TestLimit ; i++ ) {
7204 *TestAddr = i * 4;
7205 TestAddr++;
7206 }
7207
7208 TestAddr = (unsigned long *)info->memory_base;
7209
7210 for ( i = 0 ; i < TestLimit ; i++ ) {
7211 if ( *TestAddr != i * 4 )
7212 return false;
7213 TestAddr++;
7214 }
7215
7216 memset( info->memory_base, 0, SHARED_MEM_ADDRESS_SIZE );
7217
7218 return true;
7219
7220} /* End Of mgsl_memory_test() */
7221
7222
7223/* mgsl_load_pci_memory()
7224 *
7225 * Load a large block of data into the PCI shared memory.
7226 * Use this instead of memcpy() or memmove() to move data
7227 * into the PCI shared memory.
7228 *
7229 * Notes:
7230 *
7231 * This function prevents the PCI9050 interface chip from hogging
7232 * the adapter local bus, which can starve the 16C32 by preventing
7233 * 16C32 bus master cycles.
7234 *
7235 * The PCI9050 documentation says that the 9050 will always release
7236 * control of the local bus after completing the current read
7237 * or write operation.
7238 *
7239 * It appears that as long as the PCI9050 write FIFO is full, the
7240 * PCI9050 treats all of the writes as a single burst transaction
7241 * and will not release the bus. This causes DMA latency problems
7242 * at high speeds when copying large data blocks to the shared
7243 * memory.
7244 *
7245 * This function in effect, breaks the a large shared memory write
7246 * into multiple transations by interleaving a shared memory read
7247 * which will flush the write FIFO and 'complete' the write
7248 * transation. This allows any pending DMA request to gain control
7249 * of the local bus in a timely fasion.
7250 *
7251 * Arguments:
7252 *
7253 * TargetPtr pointer to target address in PCI shared memory
7254 * SourcePtr pointer to source buffer for data
7255 * count count in bytes of data to copy
7256 *
7257 * Return Value: None
7258 */
7259static void mgsl_load_pci_memory( char* TargetPtr, const char* SourcePtr,
7260 unsigned short count )
7261{
7262 /* 16 32-bit writes @ 60ns each = 960ns max latency on local bus */
7263#define PCI_LOAD_INTERVAL 64
7264
7265 unsigned short Intervalcount = count / PCI_LOAD_INTERVAL;
7266 unsigned short Index;
7267 unsigned long Dummy;
7268
7269 for ( Index = 0 ; Index < Intervalcount ; Index++ )
7270 {
7271 memcpy(TargetPtr, SourcePtr, PCI_LOAD_INTERVAL);
7272 Dummy = *((volatile unsigned long *)TargetPtr);
7273 TargetPtr += PCI_LOAD_INTERVAL;
7274 SourcePtr += PCI_LOAD_INTERVAL;
7275 }
7276
7277 memcpy( TargetPtr, SourcePtr, count % PCI_LOAD_INTERVAL );
7278
7279} /* End Of mgsl_load_pci_memory() */
7280
7281static void mgsl_trace_block(struct mgsl_struct *info,const char* data, int count, int xmit)
7282{
7283 int i;
7284 int linecount;
7285 if (xmit)
7286 printk("%s tx data:\n",info->device_name);
7287 else
7288 printk("%s rx data:\n",info->device_name);
7289
7290 while(count) {
7291 if (count > 16)
7292 linecount = 16;
7293 else
7294 linecount = count;
7295
7296 for(i=0;i<linecount;i++)
7297 printk("%02X ",(unsigned char)data[i]);
7298 for(;i<17;i++)
7299 printk(" ");
7300 for(i=0;i<linecount;i++) {
7301 if (data[i]>=040 && data[i]<=0176)
7302 printk("%c",data[i]);
7303 else
7304 printk(".");
7305 }
7306 printk("\n");
7307
7308 data += linecount;
7309 count -= linecount;
7310 }
7311} /* end of mgsl_trace_block() */
7312
7313/* mgsl_tx_timeout()
7314 *
7315 * called when HDLC frame times out
7316 * update stats and do tx completion processing
7317 *
7318 * Arguments: context pointer to device instance data
7319 * Return Value: None
7320 */
7321static void mgsl_tx_timeout(struct timer_list *t)
7322{
7323 struct mgsl_struct *info = from_timer(info, t, tx_timer);
7324 unsigned long flags;
7325
7326 if ( debug_level >= DEBUG_LEVEL_INFO )
7327 printk( "%s(%d):mgsl_tx_timeout(%s)\n",
7328 __FILE__,__LINE__,info->device_name);
7329 if(info->tx_active &&
7330 (info->params.mode == MGSL_MODE_HDLC ||
7331 info->params.mode == MGSL_MODE_RAW) ) {
7332 info->icount.txtimeout++;
7333 }
7334 spin_lock_irqsave(&info->irq_spinlock,flags);
7335 info->tx_active = false;
7336 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
7337
7338 if ( info->params.flags & HDLC_FLAG_HDLC_LOOPMODE )
7339 usc_loopmode_cancel_transmit( info );
7340
7341 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7342
7343#if SYNCLINK_GENERIC_HDLC
7344 if (info->netcount)
7345 hdlcdev_tx_done(info);
7346 else
7347#endif
7348 mgsl_bh_transmit(info);
7349
7350} /* end of mgsl_tx_timeout() */
7351
7352/* signal that there are no more frames to send, so that
7353 * line is 'released' by echoing RxD to TxD when current
7354 * transmission is complete (or immediately if no tx in progress).
7355 */
7356static int mgsl_loopmode_send_done( struct mgsl_struct * info )
7357{
7358 unsigned long flags;
7359
7360 spin_lock_irqsave(&info->irq_spinlock,flags);
7361 if (info->params.flags & HDLC_FLAG_HDLC_LOOPMODE) {
7362 if (info->tx_active)
7363 info->loopmode_send_done_requested = true;
7364 else
7365 usc_loopmode_send_done(info);
7366 }
7367 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7368
7369 return 0;
7370}
7371
7372/* release the line by echoing RxD to TxD
7373 * upon completion of a transmit frame
7374 */
7375static void usc_loopmode_send_done( struct mgsl_struct * info )
7376{
7377 info->loopmode_send_done_requested = false;
7378 /* clear CMR:13 to 0 to start echoing RxData to TxData */
7379 info->cmr_value &= ~BIT13;
7380 usc_OutReg(info, CMR, info->cmr_value);
7381}
7382
7383/* abort a transmit in progress while in HDLC LoopMode
7384 */
7385static void usc_loopmode_cancel_transmit( struct mgsl_struct * info )
7386{
7387 /* reset tx dma channel and purge TxFifo */
7388 usc_RTCmd( info, RTCmd_PurgeTxFifo );
7389 usc_DmaCmd( info, DmaCmd_ResetTxChannel );
7390 usc_loopmode_send_done( info );
7391}
7392
7393/* for HDLC/SDLC LoopMode, setting CMR:13 after the transmitter is enabled
7394 * is an Insert Into Loop action. Upon receipt of a GoAhead sequence (RxAbort)
7395 * we must clear CMR:13 to begin repeating TxData to RxData
7396 */
7397static void usc_loopmode_insert_request( struct mgsl_struct * info )
7398{
7399 info->loopmode_insert_requested = true;
7400
7401 /* enable RxAbort irq. On next RxAbort, clear CMR:13 to
7402 * begin repeating TxData on RxData (complete insertion)
7403 */
7404 usc_OutReg( info, RICR,
7405 (usc_InReg( info, RICR ) | RXSTATUS_ABORT_RECEIVED ) );
7406
7407 /* set CMR:13 to insert into loop on next GoAhead (RxAbort) */
7408 info->cmr_value |= BIT13;
7409 usc_OutReg(info, CMR, info->cmr_value);
7410}
7411
7412/* return 1 if station is inserted into the loop, otherwise 0
7413 */
7414static int usc_loopmode_active( struct mgsl_struct * info)
7415{
7416 return usc_InReg( info, CCSR ) & BIT7 ? 1 : 0 ;
7417}
7418
7419#if SYNCLINK_GENERIC_HDLC
7420
7421/**
7422 * called by generic HDLC layer when protocol selected (PPP, frame relay, etc.)
7423 * set encoding and frame check sequence (FCS) options
7424 *
7425 * dev pointer to network device structure
7426 * encoding serial encoding setting
7427 * parity FCS setting
7428 *
7429 * returns 0 if success, otherwise error code
7430 */
7431static int hdlcdev_attach(struct net_device *dev, unsigned short encoding,
7432 unsigned short parity)
7433{
7434 struct mgsl_struct *info = dev_to_port(dev);
7435 unsigned char new_encoding;
7436 unsigned short new_crctype;
7437
7438 /* return error if TTY interface open */
7439 if (info->port.count)
7440 return -EBUSY;
7441
7442 switch (encoding)
7443 {
7444 case ENCODING_NRZ: new_encoding = HDLC_ENCODING_NRZ; break;
7445 case ENCODING_NRZI: new_encoding = HDLC_ENCODING_NRZI_SPACE; break;
7446 case ENCODING_FM_MARK: new_encoding = HDLC_ENCODING_BIPHASE_MARK; break;
7447 case ENCODING_FM_SPACE: new_encoding = HDLC_ENCODING_BIPHASE_SPACE; break;
7448 case ENCODING_MANCHESTER: new_encoding = HDLC_ENCODING_BIPHASE_LEVEL; break;
7449 default: return -EINVAL;
7450 }
7451
7452 switch (parity)
7453 {
7454 case PARITY_NONE: new_crctype = HDLC_CRC_NONE; break;
7455 case PARITY_CRC16_PR1_CCITT: new_crctype = HDLC_CRC_16_CCITT; break;
7456 case PARITY_CRC32_PR1_CCITT: new_crctype = HDLC_CRC_32_CCITT; break;
7457 default: return -EINVAL;
7458 }
7459
7460 info->params.encoding = new_encoding;
7461 info->params.crc_type = new_crctype;
7462
7463 /* if network interface up, reprogram hardware */
7464 if (info->netcount)
7465 mgsl_program_hw(info);
7466
7467 return 0;
7468}
7469
7470/**
7471 * called by generic HDLC layer to send frame
7472 *
7473 * skb socket buffer containing HDLC frame
7474 * dev pointer to network device structure
7475 */
7476static netdev_tx_t hdlcdev_xmit(struct sk_buff *skb,
7477 struct net_device *dev)
7478{
7479 struct mgsl_struct *info = dev_to_port(dev);
7480 unsigned long flags;
7481
7482 if (debug_level >= DEBUG_LEVEL_INFO)
7483 printk(KERN_INFO "%s:hdlc_xmit(%s)\n",__FILE__,dev->name);
7484
7485 /* stop sending until this frame completes */
7486 netif_stop_queue(dev);
7487
7488 /* copy data to device buffers */
7489 info->xmit_cnt = skb->len;
7490 mgsl_load_tx_dma_buffer(info, skb->data, skb->len);
7491
7492 /* update network statistics */
7493 dev->stats.tx_packets++;
7494 dev->stats.tx_bytes += skb->len;
7495
7496 /* done with socket buffer, so free it */
7497 dev_kfree_skb(skb);
7498
7499 /* save start time for transmit timeout detection */
7500 netif_trans_update(dev);
7501
7502 /* start hardware transmitter if necessary */
7503 spin_lock_irqsave(&info->irq_spinlock,flags);
7504 if (!info->tx_active)
7505 usc_start_transmitter(info);
7506 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7507
7508 return NETDEV_TX_OK;
7509}
7510
7511/**
7512 * called by network layer when interface enabled
7513 * claim resources and initialize hardware
7514 *
7515 * dev pointer to network device structure
7516 *
7517 * returns 0 if success, otherwise error code
7518 */
7519static int hdlcdev_open(struct net_device *dev)
7520{
7521 struct mgsl_struct *info = dev_to_port(dev);
7522 int rc;
7523 unsigned long flags;
7524
7525 if (debug_level >= DEBUG_LEVEL_INFO)
7526 printk("%s:hdlcdev_open(%s)\n",__FILE__,dev->name);
7527
7528 /* generic HDLC layer open processing */
7529 rc = hdlc_open(dev);
7530 if (rc)
7531 return rc;
7532
7533 /* arbitrate between network and tty opens */
7534 spin_lock_irqsave(&info->netlock, flags);
7535 if (info->port.count != 0 || info->netcount != 0) {
7536 printk(KERN_WARNING "%s: hdlc_open returning busy\n", dev->name);
7537 spin_unlock_irqrestore(&info->netlock, flags);
7538 return -EBUSY;
7539 }
7540 info->netcount=1;
7541 spin_unlock_irqrestore(&info->netlock, flags);
7542
7543 /* claim resources and init adapter */
7544 if ((rc = startup(info)) != 0) {
7545 spin_lock_irqsave(&info->netlock, flags);
7546 info->netcount=0;
7547 spin_unlock_irqrestore(&info->netlock, flags);
7548 return rc;
7549 }
7550
7551 /* assert RTS and DTR, apply hardware settings */
7552 info->serial_signals |= SerialSignal_RTS | SerialSignal_DTR;
7553 mgsl_program_hw(info);
7554
7555 /* enable network layer transmit */
7556 netif_trans_update(dev);
7557 netif_start_queue(dev);
7558
7559 /* inform generic HDLC layer of current DCD status */
7560 spin_lock_irqsave(&info->irq_spinlock, flags);
7561 usc_get_serial_signals(info);
7562 spin_unlock_irqrestore(&info->irq_spinlock, flags);
7563 if (info->serial_signals & SerialSignal_DCD)
7564 netif_carrier_on(dev);
7565 else
7566 netif_carrier_off(dev);
7567 return 0;
7568}
7569
7570/**
7571 * called by network layer when interface is disabled
7572 * shutdown hardware and release resources
7573 *
7574 * dev pointer to network device structure
7575 *
7576 * returns 0 if success, otherwise error code
7577 */
7578static int hdlcdev_close(struct net_device *dev)
7579{
7580 struct mgsl_struct *info = dev_to_port(dev);
7581 unsigned long flags;
7582
7583 if (debug_level >= DEBUG_LEVEL_INFO)
7584 printk("%s:hdlcdev_close(%s)\n",__FILE__,dev->name);
7585
7586 netif_stop_queue(dev);
7587
7588 /* shutdown adapter and release resources */
7589 shutdown(info);
7590
7591 hdlc_close(dev);
7592
7593 spin_lock_irqsave(&info->netlock, flags);
7594 info->netcount=0;
7595 spin_unlock_irqrestore(&info->netlock, flags);
7596
7597 return 0;
7598}
7599
7600/**
7601 * called by network layer to process IOCTL call to network device
7602 *
7603 * dev pointer to network device structure
7604 * ifr pointer to network interface request structure
7605 * cmd IOCTL command code
7606 *
7607 * returns 0 if success, otherwise error code
7608 */
7609static int hdlcdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
7610{
7611 const size_t size = sizeof(sync_serial_settings);
7612 sync_serial_settings new_line;
7613 sync_serial_settings __user *line = ifr->ifr_settings.ifs_ifsu.sync;
7614 struct mgsl_struct *info = dev_to_port(dev);
7615 unsigned int flags;
7616
7617 if (debug_level >= DEBUG_LEVEL_INFO)
7618 printk("%s:hdlcdev_ioctl(%s)\n",__FILE__,dev->name);
7619
7620 /* return error if TTY interface open */
7621 if (info->port.count)
7622 return -EBUSY;
7623
7624 if (cmd != SIOCWANDEV)
7625 return hdlc_ioctl(dev, ifr, cmd);
7626
7627 switch(ifr->ifr_settings.type) {
7628 case IF_GET_IFACE: /* return current sync_serial_settings */
7629
7630 ifr->ifr_settings.type = IF_IFACE_SYNC_SERIAL;
7631 if (ifr->ifr_settings.size < size) {
7632 ifr->ifr_settings.size = size; /* data size wanted */
7633 return -ENOBUFS;
7634 }
7635
7636 flags = info->params.flags & (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
7637 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
7638 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
7639 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN);
7640
7641 memset(&new_line, 0, sizeof(new_line));
7642 switch (flags){
7643 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN): new_line.clock_type = CLOCK_EXT; break;
7644 case (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG): new_line.clock_type = CLOCK_INT; break;
7645 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG): new_line.clock_type = CLOCK_TXINT; break;
7646 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN): new_line.clock_type = CLOCK_TXFROMRX; break;
7647 default: new_line.clock_type = CLOCK_DEFAULT;
7648 }
7649
7650 new_line.clock_rate = info->params.clock_speed;
7651 new_line.loopback = info->params.loopback ? 1:0;
7652
7653 if (copy_to_user(line, &new_line, size))
7654 return -EFAULT;
7655 return 0;
7656
7657 case IF_IFACE_SYNC_SERIAL: /* set sync_serial_settings */
7658
7659 if(!capable(CAP_NET_ADMIN))
7660 return -EPERM;
7661 if (copy_from_user(&new_line, line, size))
7662 return -EFAULT;
7663
7664 switch (new_line.clock_type)
7665 {
7666 case CLOCK_EXT: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN; break;
7667 case CLOCK_TXFROMRX: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN; break;
7668 case CLOCK_INT: flags = HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG; break;
7669 case CLOCK_TXINT: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG; break;
7670 case CLOCK_DEFAULT: flags = info->params.flags &
7671 (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
7672 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
7673 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
7674 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN); break;
7675 default: return -EINVAL;
7676 }
7677
7678 if (new_line.loopback != 0 && new_line.loopback != 1)
7679 return -EINVAL;
7680
7681 info->params.flags &= ~(HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
7682 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
7683 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
7684 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN);
7685 info->params.flags |= flags;
7686
7687 info->params.loopback = new_line.loopback;
7688
7689 if (flags & (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG))
7690 info->params.clock_speed = new_line.clock_rate;
7691 else
7692 info->params.clock_speed = 0;
7693
7694 /* if network interface up, reprogram hardware */
7695 if (info->netcount)
7696 mgsl_program_hw(info);
7697 return 0;
7698
7699 default:
7700 return hdlc_ioctl(dev, ifr, cmd);
7701 }
7702}
7703
7704/**
7705 * called by network layer when transmit timeout is detected
7706 *
7707 * dev pointer to network device structure
7708 */
7709static void hdlcdev_tx_timeout(struct net_device *dev, unsigned int txqueue)
7710{
7711 struct mgsl_struct *info = dev_to_port(dev);
7712 unsigned long flags;
7713
7714 if (debug_level >= DEBUG_LEVEL_INFO)
7715 printk("hdlcdev_tx_timeout(%s)\n",dev->name);
7716
7717 dev->stats.tx_errors++;
7718 dev->stats.tx_aborted_errors++;
7719
7720 spin_lock_irqsave(&info->irq_spinlock,flags);
7721 usc_stop_transmitter(info);
7722 spin_unlock_irqrestore(&info->irq_spinlock,flags);
7723
7724 netif_wake_queue(dev);
7725}
7726
7727/**
7728 * called by device driver when transmit completes
7729 * reenable network layer transmit if stopped
7730 *
7731 * info pointer to device instance information
7732 */
7733static void hdlcdev_tx_done(struct mgsl_struct *info)
7734{
7735 if (netif_queue_stopped(info->netdev))
7736 netif_wake_queue(info->netdev);
7737}
7738
7739/**
7740 * called by device driver when frame received
7741 * pass frame to network layer
7742 *
7743 * info pointer to device instance information
7744 * buf pointer to buffer contianing frame data
7745 * size count of data bytes in buf
7746 */
7747static void hdlcdev_rx(struct mgsl_struct *info, char *buf, int size)
7748{
7749 struct sk_buff *skb = dev_alloc_skb(size);
7750 struct net_device *dev = info->netdev;
7751
7752 if (debug_level >= DEBUG_LEVEL_INFO)
7753 printk("hdlcdev_rx(%s)\n", dev->name);
7754
7755 if (skb == NULL) {
7756 printk(KERN_NOTICE "%s: can't alloc skb, dropping packet\n",
7757 dev->name);
7758 dev->stats.rx_dropped++;
7759 return;
7760 }
7761
7762 skb_put_data(skb, buf, size);
7763
7764 skb->protocol = hdlc_type_trans(skb, dev);
7765
7766 dev->stats.rx_packets++;
7767 dev->stats.rx_bytes += size;
7768
7769 netif_rx(skb);
7770}
7771
7772static const struct net_device_ops hdlcdev_ops = {
7773 .ndo_open = hdlcdev_open,
7774 .ndo_stop = hdlcdev_close,
7775 .ndo_start_xmit = hdlc_start_xmit,
7776 .ndo_do_ioctl = hdlcdev_ioctl,
7777 .ndo_tx_timeout = hdlcdev_tx_timeout,
7778};
7779
7780/**
7781 * called by device driver when adding device instance
7782 * do generic HDLC initialization
7783 *
7784 * info pointer to device instance information
7785 *
7786 * returns 0 if success, otherwise error code
7787 */
7788static int hdlcdev_init(struct mgsl_struct *info)
7789{
7790 int rc;
7791 struct net_device *dev;
7792 hdlc_device *hdlc;
7793
7794 /* allocate and initialize network and HDLC layer objects */
7795
7796 dev = alloc_hdlcdev(info);
7797 if (!dev) {
7798 printk(KERN_ERR "%s:hdlc device allocation failure\n",__FILE__);
7799 return -ENOMEM;
7800 }
7801
7802 /* for network layer reporting purposes only */
7803 dev->base_addr = info->io_base;
7804 dev->irq = info->irq_level;
7805 dev->dma = info->dma_level;
7806
7807 /* network layer callbacks and settings */
7808 dev->netdev_ops = &hdlcdev_ops;
7809 dev->watchdog_timeo = 10 * HZ;
7810 dev->tx_queue_len = 50;
7811
7812 /* generic HDLC layer callbacks and settings */
7813 hdlc = dev_to_hdlc(dev);
7814 hdlc->attach = hdlcdev_attach;
7815 hdlc->xmit = hdlcdev_xmit;
7816
7817 /* register objects with HDLC layer */
7818 rc = register_hdlc_device(dev);
7819 if (rc) {
7820 printk(KERN_WARNING "%s:unable to register hdlc device\n",__FILE__);
7821 free_netdev(dev);
7822 return rc;
7823 }
7824
7825 info->netdev = dev;
7826 return 0;
7827}
7828
7829/**
7830 * called by device driver when removing device instance
7831 * do generic HDLC cleanup
7832 *
7833 * info pointer to device instance information
7834 */
7835static void hdlcdev_exit(struct mgsl_struct *info)
7836{
7837 unregister_hdlc_device(info->netdev);
7838 free_netdev(info->netdev);
7839 info->netdev = NULL;
7840}
7841
7842#endif /* CONFIG_HDLC */
7843
7844
7845static int synclink_init_one (struct pci_dev *dev,
7846 const struct pci_device_id *ent)
7847{
7848 struct mgsl_struct *info;
7849
7850 if (pci_enable_device(dev)) {
7851 printk("error enabling pci device %p\n", dev);
7852 return -EIO;
7853 }
7854
7855 info = mgsl_allocate_device();
7856 if (!info) {
7857 printk("can't allocate device instance data.\n");
7858 return -EIO;
7859 }
7860
7861 /* Copy user configuration info to device instance data */
7862
7863 info->io_base = pci_resource_start(dev, 2);
7864 info->irq_level = dev->irq;
7865 info->phys_memory_base = pci_resource_start(dev, 3);
7866
7867 /* Because veremap only works on page boundaries we must map
7868 * a larger area than is actually implemented for the LCR
7869 * memory range. We map a full page starting at the page boundary.
7870 */
7871 info->phys_lcr_base = pci_resource_start(dev, 0);
7872 info->lcr_offset = info->phys_lcr_base & (PAGE_SIZE-1);
7873 info->phys_lcr_base &= ~(PAGE_SIZE-1);
7874
7875 info->io_addr_size = 8;
7876 info->irq_flags = IRQF_SHARED;
7877
7878 if (dev->device == 0x0210) {
7879 /* Version 1 PCI9030 based universal PCI adapter */
7880 info->misc_ctrl_value = 0x007c4080;
7881 info->hw_version = 1;
7882 } else {
7883 /* Version 0 PCI9050 based 5V PCI adapter
7884 * A PCI9050 bug prevents reading LCR registers if
7885 * LCR base address bit 7 is set. Maintain shadow
7886 * value so we can write to LCR misc control reg.
7887 */
7888 info->misc_ctrl_value = 0x087e4546;
7889 info->hw_version = 0;
7890 }
7891
7892 mgsl_add_device(info);
7893
7894 return 0;
7895}
7896
7897static void synclink_remove_one (struct pci_dev *dev)
7898{
7899}
7900