Loading...
1config ATH9K_HW
2 tristate
3config ATH9K_COMMON
4 tristate
5
6config ATH9K
7 tristate "Atheros 802.11n wireless cards support"
8 depends on MAC80211
9 select ATH9K_HW
10 select MAC80211_LEDS
11 select LEDS_CLASS
12 select NEW_LEDS
13 select ATH9K_COMMON
14 ---help---
15 This module adds support for wireless adapters based on
16 Atheros IEEE 802.11n AR5008, AR9001 and AR9002 family
17 of chipsets. For a specific list of supported external
18 cards, laptops that already ship with these cards and
19 APs that come with these cards refer to to ath9k wiki
20 products page:
21
22 http://wireless.kernel.org/en/users/Drivers/ath9k/products
23
24 If you choose to build a module, it'll be called ath9k.
25
26config ATH9K_PCI
27 bool "Atheros ath9k PCI/PCIe bus support"
28 depends on ATH9K && PCI
29 ---help---
30 This option enables the PCI bus support in ath9k.
31
32 Say Y, if you have a compatible PCI/PCIe wireless card.
33
34config ATH9K_AHB
35 bool "Atheros ath9k AHB bus support"
36 depends on ATH9K
37 default n
38 ---help---
39 This option enables the AHB bus support in ath9k.
40
41 Say Y, if you have a SoC with a compatible built-in
42 wireless MAC. Say N if unsure.
43
44config ATH9K_DEBUGFS
45 bool "Atheros ath9k debugging"
46 depends on ATH9K && DEBUG_FS
47 ---help---
48 Say Y, if you need access to ath9k's statistics for
49 interrupts, rate control, etc.
50
51 Also required for changing debug message flags at run time.
52
53config ATH9K_RATE_CONTROL
54 bool "Atheros ath9k rate control"
55 depends on ATH9K
56 default y
57 ---help---
58 Say Y, if you want to use the ath9k specific rate control
59 module instead of minstrel_ht.
60
61config ATH9K_HTC
62 tristate "Atheros HTC based wireless cards support"
63 depends on USB && MAC80211
64 select ATH9K_HW
65 select MAC80211_LEDS
66 select LEDS_CLASS
67 select NEW_LEDS
68 select ATH9K_COMMON
69 ---help---
70 Support for Atheros HTC based cards.
71 Chipsets supported: AR9271
72
73 For more information: http://wireless.kernel.org/en/users/Drivers/ath9k_htc
74
75 The built module will be ath9k_htc.
76
77config ATH9K_HTC_DEBUGFS
78 bool "Atheros ath9k_htc debugging"
79 depends on ATH9K_HTC && DEBUG_FS
80 ---help---
81 Say Y, if you need access to ath9k_htc's statistics.
1# SPDX-License-Identifier: ISC
2config ATH9K_HW
3 tristate
4config ATH9K_COMMON
5 tristate
6 select ATH_COMMON
7config ATH9K_COMMON_DEBUG
8 bool
9config ATH9K_DFS_DEBUGFS
10 def_bool y
11 depends on ATH9K_DEBUGFS && ATH9K_DFS_CERTIFIED
12
13config ATH9K_BTCOEX_SUPPORT
14 bool "Atheros bluetooth coexistence support"
15 depends on (ATH9K || ATH9K_HTC)
16 default y
17 help
18 Say Y, if you want to use the ath9k/ath9k_htc radios together with
19 Bluetooth modules in the same system.
20
21config ATH9K
22 tristate "Atheros 802.11n wireless cards support"
23 depends on MAC80211 && HAS_DMA
24 select ATH9K_HW
25 select MAC80211_LEDS
26 select LEDS_CLASS
27 select NEW_LEDS
28 select ATH9K_COMMON
29 help
30 This module adds support for wireless adapters based on
31 Atheros IEEE 802.11n AR5008, AR9001 and AR9002 family
32 of chipsets. For a specific list of supported external
33 cards, laptops that already ship with these cards and
34 APs that come with these cards refer to ath9k wiki
35 products page:
36
37 https://wireless.wiki.kernel.org/en/users/Drivers/ath9k/products
38
39 If you choose to build a module, it'll be called ath9k.
40
41config ATH9K_PCI
42 bool "Atheros ath9k PCI/PCIe bus support"
43 default y
44 depends on ATH9K && PCI
45 help
46 This option enables the PCI bus support in ath9k.
47
48 Say Y, if you have a compatible PCI/PCIe wireless card.
49
50config ATH9K_AHB
51 bool "Atheros ath9k AHB bus support"
52 depends on ATH9K
53 default n
54 help
55 This option enables the AHB bus support in ath9k.
56
57 Say Y, if you have a SoC with a compatible built-in
58 wireless MAC. Say N if unsure.
59
60config ATH9K_DEBUGFS
61 bool "Atheros ath9k debugging"
62 depends on ATH9K && DEBUG_FS
63 select MAC80211_DEBUGFS
64 select ATH9K_COMMON_DEBUG
65 help
66 Say Y, if you need access to ath9k's statistics for
67 interrupts, rate control, etc.
68
69 Also required for changing debug message flags at run time and for
70 TX99.
71
72config ATH9K_STATION_STATISTICS
73 bool "Detailed station statistics"
74 depends on ATH9K && ATH9K_DEBUGFS && DEBUG_FS
75 select MAC80211_DEBUGFS
76 default n
77 help
78 This option enables detailed statistics for association stations.
79
80config ATH9K_TX99
81 bool "Atheros ath9k TX99 testing support"
82 depends on ATH9K_DEBUGFS && CFG80211_CERTIFICATION_ONUS
83 default n
84 help
85 Say N. This should only be enabled on systems undergoing
86 certification testing and evaluation in a controlled environment.
87 Enabling this will only enable TX99 support, all other modes of
88 operation will be disabled.
89
90 TX99 support enables Specific Absorption Rate (SAR) testing.
91 SAR is the unit of measurement for the amount of radio frequency(RF)
92 absorbed by the body when using a wireless device. The RF exposure
93 limits used are expressed in the terms of SAR, which is a measure
94 of the electric and magnetic field strength and power density for
95 transmitters operating at frequencies from 300 kHz to 100 GHz.
96 Regulatory bodies around the world require that wireless device
97 be evaluated to meet the RF exposure limits set forth in the
98 governmental SAR regulations.
99
100config ATH9K_DFS_CERTIFIED
101 bool "Atheros DFS support for certified platforms"
102 depends on ATH9K && CFG80211_CERTIFICATION_ONUS
103 default n
104 help
105 This option enables DFS support for initiating radiation on
106 ath9k. There is no way to dynamically detect if a card was DFS
107 certified and as such this is left as a build time option. This
108 option should only be enabled by system integrators that can
109 guarantee that all the platforms that their kernel will run on
110 have obtained appropriate regulatory body certification for a
111 respective Atheros card by using ath9k on the target shipping
112 platforms.
113
114 This is currently only a placeholder for future DFS support,
115 as DFS support requires more components that still need to be
116 developed. At this point enabling this option won't do anything
117 except increase code size.
118
119config ATH9K_DYNACK
120 bool "Atheros ath9k ACK timeout estimation algorithm"
121 depends on ATH9K
122 default n
123 help
124 This option enables ath9k dynamic ACK timeout estimation algorithm
125 based on ACK frame RX timestamp, TX frame timestamp and frame
126 duration
127
128config ATH9K_WOW
129 bool "Wake on Wireless LAN support (EXPERIMENTAL)"
130 depends on ATH9K && PM
131 default n
132 help
133 This option enables Wake on Wireless LAN support for certain cards.
134 Currently, AR9462 is supported.
135
136config ATH9K_RFKILL
137 bool "Atheros ath9k rfkill support" if EXPERT
138 depends on ATH9K
139 depends on RFKILL=y || RFKILL=ATH9K
140 default y
141 help
142 Say Y to have ath9k poll the RF-Kill GPIO every couple of
143 seconds. Turn off to save power, but enable it if you have
144 a platform that can toggle the RF-Kill GPIO.
145
146config ATH9K_CHANNEL_CONTEXT
147 bool "Channel Context support"
148 depends on ATH9K
149 default n
150 help
151 This option enables channel context support in ath9k, which is needed
152 for multi-channel concurrency. Enable this if P2P PowerSave support
153 is required.
154
155config ATH9K_PCOEM
156 bool "Atheros ath9k support for PC OEM cards" if EXPERT
157 depends on ATH9K
158 default y
159
160config ATH9K_PCI_NO_EEPROM
161 tristate "Atheros ath9k pci loader for EEPROM-less chips"
162 depends on ATH9K_PCI
163 default n
164 help
165 This separate driver provides a loader in order to support the
166 AR500X to AR92XX-generation of ath9k PCI(e) WiFi chips, which have
167 their initialization data (which contains the real PCI Device ID
168 that ath9k will need) stored together with the calibration data out
169 of reach for the ath9k chip.
170
171 These devices are usually various network appliances, routers or
172 access Points and such.
173
174 If unsure say N.
175
176config ATH9K_HTC
177 tristate "Atheros HTC based wireless cards support"
178 depends on USB && MAC80211
179 select ATH9K_HW
180 select MAC80211_LEDS
181 select LEDS_CLASS
182 select NEW_LEDS
183 select ATH9K_COMMON
184 help
185 Support for Atheros HTC based cards.
186 Chipsets supported: AR9271
187
188 For more information:
189 https://wireless.wiki.kernel.org/en/users/Drivers/ath9k_htc
190
191 The built module will be ath9k_htc.
192
193config ATH9K_HTC_DEBUGFS
194 bool "Atheros ath9k_htc debugging"
195 depends on ATH9K_HTC && DEBUG_FS
196 select ATH9K_COMMON_DEBUG
197 help
198 Say Y, if you need access to ath9k_htc's statistics.
199 As well as access to the FFT/spectral data.
200
201config ATH9K_HWRNG
202 bool "Random number generator support"
203 depends on ATH9K && (HW_RANDOM = y || HW_RANDOM = ATH9K)
204 default n
205 help
206 This option incorporates the ADC register output as a source of
207 randomness into Linux entropy pool (/dev/urandom and /dev/random)
208
209 Say Y, feeds the entropy directly from the WiFi driver to the input
210 pool.
211
212config ATH9K_COMMON_SPECTRAL
213 bool "Atheros ath9k/ath9k_htc spectral scan support"
214 depends on ATH9K_DEBUGFS || ATH9K_HTC_DEBUGFS
215 select RELAY
216 default n
217 help
218 Say Y to enable access to the FFT/spectral data via debugfs.