Loading...
Note: File does not exist in v3.1.
1// SPDX-License-Identifier: GPL-2.0
2/* Copyright(c) 1999 - 2018 Intel Corporation. */
3
4#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
5
6#include <linux/module.h>
7#include <linux/types.h>
8#include <linux/init.h>
9#include <linux/pci.h>
10#include <linux/vmalloc.h>
11#include <linux/pagemap.h>
12#include <linux/delay.h>
13#include <linux/netdevice.h>
14#include <linux/interrupt.h>
15#include <linux/tcp.h>
16#include <linux/ipv6.h>
17#include <linux/slab.h>
18#include <net/checksum.h>
19#include <net/ip6_checksum.h>
20#include <linux/ethtool.h>
21#include <linux/if_vlan.h>
22#include <linux/cpu.h>
23#include <linux/smp.h>
24#include <linux/pm_qos.h>
25#include <linux/pm_runtime.h>
26#include <linux/aer.h>
27#include <linux/prefetch.h>
28
29#include "e1000.h"
30
31char e1000e_driver_name[] = "e1000e";
32
33#define DEFAULT_MSG_ENABLE (NETIF_MSG_DRV|NETIF_MSG_PROBE|NETIF_MSG_LINK)
34static int debug = -1;
35module_param(debug, int, 0);
36MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
37
38static const struct e1000_info *e1000_info_tbl[] = {
39 [board_82571] = &e1000_82571_info,
40 [board_82572] = &e1000_82572_info,
41 [board_82573] = &e1000_82573_info,
42 [board_82574] = &e1000_82574_info,
43 [board_82583] = &e1000_82583_info,
44 [board_80003es2lan] = &e1000_es2_info,
45 [board_ich8lan] = &e1000_ich8_info,
46 [board_ich9lan] = &e1000_ich9_info,
47 [board_ich10lan] = &e1000_ich10_info,
48 [board_pchlan] = &e1000_pch_info,
49 [board_pch2lan] = &e1000_pch2_info,
50 [board_pch_lpt] = &e1000_pch_lpt_info,
51 [board_pch_spt] = &e1000_pch_spt_info,
52 [board_pch_cnp] = &e1000_pch_cnp_info,
53};
54
55struct e1000_reg_info {
56 u32 ofs;
57 char *name;
58};
59
60static const struct e1000_reg_info e1000_reg_info_tbl[] = {
61 /* General Registers */
62 {E1000_CTRL, "CTRL"},
63 {E1000_STATUS, "STATUS"},
64 {E1000_CTRL_EXT, "CTRL_EXT"},
65
66 /* Interrupt Registers */
67 {E1000_ICR, "ICR"},
68
69 /* Rx Registers */
70 {E1000_RCTL, "RCTL"},
71 {E1000_RDLEN(0), "RDLEN"},
72 {E1000_RDH(0), "RDH"},
73 {E1000_RDT(0), "RDT"},
74 {E1000_RDTR, "RDTR"},
75 {E1000_RXDCTL(0), "RXDCTL"},
76 {E1000_ERT, "ERT"},
77 {E1000_RDBAL(0), "RDBAL"},
78 {E1000_RDBAH(0), "RDBAH"},
79 {E1000_RDFH, "RDFH"},
80 {E1000_RDFT, "RDFT"},
81 {E1000_RDFHS, "RDFHS"},
82 {E1000_RDFTS, "RDFTS"},
83 {E1000_RDFPC, "RDFPC"},
84
85 /* Tx Registers */
86 {E1000_TCTL, "TCTL"},
87 {E1000_TDBAL(0), "TDBAL"},
88 {E1000_TDBAH(0), "TDBAH"},
89 {E1000_TDLEN(0), "TDLEN"},
90 {E1000_TDH(0), "TDH"},
91 {E1000_TDT(0), "TDT"},
92 {E1000_TIDV, "TIDV"},
93 {E1000_TXDCTL(0), "TXDCTL"},
94 {E1000_TADV, "TADV"},
95 {E1000_TARC(0), "TARC"},
96 {E1000_TDFH, "TDFH"},
97 {E1000_TDFT, "TDFT"},
98 {E1000_TDFHS, "TDFHS"},
99 {E1000_TDFTS, "TDFTS"},
100 {E1000_TDFPC, "TDFPC"},
101
102 /* List Terminator */
103 {0, NULL}
104};
105
106struct e1000e_me_supported {
107 u16 device_id; /* supported device ID */
108};
109
110static const struct e1000e_me_supported me_supported[] = {
111 {E1000_DEV_ID_PCH_LPT_I217_LM},
112 {E1000_DEV_ID_PCH_LPTLP_I218_LM},
113 {E1000_DEV_ID_PCH_I218_LM2},
114 {E1000_DEV_ID_PCH_I218_LM3},
115 {E1000_DEV_ID_PCH_SPT_I219_LM},
116 {E1000_DEV_ID_PCH_SPT_I219_LM2},
117 {E1000_DEV_ID_PCH_LBG_I219_LM3},
118 {E1000_DEV_ID_PCH_SPT_I219_LM4},
119 {E1000_DEV_ID_PCH_SPT_I219_LM5},
120 {E1000_DEV_ID_PCH_CNP_I219_LM6},
121 {E1000_DEV_ID_PCH_CNP_I219_LM7},
122 {E1000_DEV_ID_PCH_ICP_I219_LM8},
123 {E1000_DEV_ID_PCH_ICP_I219_LM9},
124 {E1000_DEV_ID_PCH_CMP_I219_LM10},
125 {E1000_DEV_ID_PCH_CMP_I219_LM11},
126 {E1000_DEV_ID_PCH_CMP_I219_LM12},
127 {E1000_DEV_ID_PCH_TGP_I219_LM13},
128 {E1000_DEV_ID_PCH_TGP_I219_LM14},
129 {E1000_DEV_ID_PCH_TGP_I219_LM15},
130 {0}
131};
132
133static bool e1000e_check_me(u16 device_id)
134{
135 struct e1000e_me_supported *id;
136
137 for (id = (struct e1000e_me_supported *)me_supported;
138 id->device_id; id++)
139 if (device_id == id->device_id)
140 return true;
141
142 return false;
143}
144
145/**
146 * __ew32_prepare - prepare to write to MAC CSR register on certain parts
147 * @hw: pointer to the HW structure
148 *
149 * When updating the MAC CSR registers, the Manageability Engine (ME) could
150 * be accessing the registers at the same time. Normally, this is handled in
151 * h/w by an arbiter but on some parts there is a bug that acknowledges Host
152 * accesses later than it should which could result in the register to have
153 * an incorrect value. Workaround this by checking the FWSM register which
154 * has bit 24 set while ME is accessing MAC CSR registers, wait if it is set
155 * and try again a number of times.
156 **/
157static void __ew32_prepare(struct e1000_hw *hw)
158{
159 s32 i = E1000_ICH_FWSM_PCIM2PCI_COUNT;
160
161 while ((er32(FWSM) & E1000_ICH_FWSM_PCIM2PCI) && --i)
162 udelay(50);
163}
164
165void __ew32(struct e1000_hw *hw, unsigned long reg, u32 val)
166{
167 if (hw->adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA)
168 __ew32_prepare(hw);
169
170 writel(val, hw->hw_addr + reg);
171}
172
173/**
174 * e1000_regdump - register printout routine
175 * @hw: pointer to the HW structure
176 * @reginfo: pointer to the register info table
177 **/
178static void e1000_regdump(struct e1000_hw *hw, struct e1000_reg_info *reginfo)
179{
180 int n = 0;
181 char rname[16];
182 u32 regs[8];
183
184 switch (reginfo->ofs) {
185 case E1000_RXDCTL(0):
186 for (n = 0; n < 2; n++)
187 regs[n] = __er32(hw, E1000_RXDCTL(n));
188 break;
189 case E1000_TXDCTL(0):
190 for (n = 0; n < 2; n++)
191 regs[n] = __er32(hw, E1000_TXDCTL(n));
192 break;
193 case E1000_TARC(0):
194 for (n = 0; n < 2; n++)
195 regs[n] = __er32(hw, E1000_TARC(n));
196 break;
197 default:
198 pr_info("%-15s %08x\n",
199 reginfo->name, __er32(hw, reginfo->ofs));
200 return;
201 }
202
203 snprintf(rname, 16, "%s%s", reginfo->name, "[0-1]");
204 pr_info("%-15s %08x %08x\n", rname, regs[0], regs[1]);
205}
206
207static void e1000e_dump_ps_pages(struct e1000_adapter *adapter,
208 struct e1000_buffer *bi)
209{
210 int i;
211 struct e1000_ps_page *ps_page;
212
213 for (i = 0; i < adapter->rx_ps_pages; i++) {
214 ps_page = &bi->ps_pages[i];
215
216 if (ps_page->page) {
217 pr_info("packet dump for ps_page %d:\n", i);
218 print_hex_dump(KERN_INFO, "", DUMP_PREFIX_ADDRESS,
219 16, 1, page_address(ps_page->page),
220 PAGE_SIZE, true);
221 }
222 }
223}
224
225/**
226 * e1000e_dump - Print registers, Tx-ring and Rx-ring
227 * @adapter: board private structure
228 **/
229static void e1000e_dump(struct e1000_adapter *adapter)
230{
231 struct net_device *netdev = adapter->netdev;
232 struct e1000_hw *hw = &adapter->hw;
233 struct e1000_reg_info *reginfo;
234 struct e1000_ring *tx_ring = adapter->tx_ring;
235 struct e1000_tx_desc *tx_desc;
236 struct my_u0 {
237 __le64 a;
238 __le64 b;
239 } *u0;
240 struct e1000_buffer *buffer_info;
241 struct e1000_ring *rx_ring = adapter->rx_ring;
242 union e1000_rx_desc_packet_split *rx_desc_ps;
243 union e1000_rx_desc_extended *rx_desc;
244 struct my_u1 {
245 __le64 a;
246 __le64 b;
247 __le64 c;
248 __le64 d;
249 } *u1;
250 u32 staterr;
251 int i = 0;
252
253 if (!netif_msg_hw(adapter))
254 return;
255
256 /* Print netdevice Info */
257 if (netdev) {
258 dev_info(&adapter->pdev->dev, "Net device Info\n");
259 pr_info("Device Name state trans_start\n");
260 pr_info("%-15s %016lX %016lX\n", netdev->name,
261 netdev->state, dev_trans_start(netdev));
262 }
263
264 /* Print Registers */
265 dev_info(&adapter->pdev->dev, "Register Dump\n");
266 pr_info(" Register Name Value\n");
267 for (reginfo = (struct e1000_reg_info *)e1000_reg_info_tbl;
268 reginfo->name; reginfo++) {
269 e1000_regdump(hw, reginfo);
270 }
271
272 /* Print Tx Ring Summary */
273 if (!netdev || !netif_running(netdev))
274 return;
275
276 dev_info(&adapter->pdev->dev, "Tx Ring Summary\n");
277 pr_info("Queue [NTU] [NTC] [bi(ntc)->dma ] leng ntw timestamp\n");
278 buffer_info = &tx_ring->buffer_info[tx_ring->next_to_clean];
279 pr_info(" %5d %5X %5X %016llX %04X %3X %016llX\n",
280 0, tx_ring->next_to_use, tx_ring->next_to_clean,
281 (unsigned long long)buffer_info->dma,
282 buffer_info->length,
283 buffer_info->next_to_watch,
284 (unsigned long long)buffer_info->time_stamp);
285
286 /* Print Tx Ring */
287 if (!netif_msg_tx_done(adapter))
288 goto rx_ring_summary;
289
290 dev_info(&adapter->pdev->dev, "Tx Ring Dump\n");
291
292 /* Transmit Descriptor Formats - DEXT[29] is 0 (Legacy) or 1 (Extended)
293 *
294 * Legacy Transmit Descriptor
295 * +--------------------------------------------------------------+
296 * 0 | Buffer Address [63:0] (Reserved on Write Back) |
297 * +--------------------------------------------------------------+
298 * 8 | Special | CSS | Status | CMD | CSO | Length |
299 * +--------------------------------------------------------------+
300 * 63 48 47 36 35 32 31 24 23 16 15 0
301 *
302 * Extended Context Descriptor (DTYP=0x0) for TSO or checksum offload
303 * 63 48 47 40 39 32 31 16 15 8 7 0
304 * +----------------------------------------------------------------+
305 * 0 | TUCSE | TUCS0 | TUCSS | IPCSE | IPCS0 | IPCSS |
306 * +----------------------------------------------------------------+
307 * 8 | MSS | HDRLEN | RSV | STA | TUCMD | DTYP | PAYLEN |
308 * +----------------------------------------------------------------+
309 * 63 48 47 40 39 36 35 32 31 24 23 20 19 0
310 *
311 * Extended Data Descriptor (DTYP=0x1)
312 * +----------------------------------------------------------------+
313 * 0 | Buffer Address [63:0] |
314 * +----------------------------------------------------------------+
315 * 8 | VLAN tag | POPTS | Rsvd | Status | Command | DTYP | DTALEN |
316 * +----------------------------------------------------------------+
317 * 63 48 47 40 39 36 35 32 31 24 23 20 19 0
318 */
319 pr_info("Tl[desc] [address 63:0 ] [SpeCssSCmCsLen] [bi->dma ] leng ntw timestamp bi->skb <-- Legacy format\n");
320 pr_info("Tc[desc] [Ce CoCsIpceCoS] [MssHlRSCm0Plen] [bi->dma ] leng ntw timestamp bi->skb <-- Ext Context format\n");
321 pr_info("Td[desc] [address 63:0 ] [VlaPoRSCm1Dlen] [bi->dma ] leng ntw timestamp bi->skb <-- Ext Data format\n");
322 for (i = 0; tx_ring->desc && (i < tx_ring->count); i++) {
323 const char *next_desc;
324 tx_desc = E1000_TX_DESC(*tx_ring, i);
325 buffer_info = &tx_ring->buffer_info[i];
326 u0 = (struct my_u0 *)tx_desc;
327 if (i == tx_ring->next_to_use && i == tx_ring->next_to_clean)
328 next_desc = " NTC/U";
329 else if (i == tx_ring->next_to_use)
330 next_desc = " NTU";
331 else if (i == tx_ring->next_to_clean)
332 next_desc = " NTC";
333 else
334 next_desc = "";
335 pr_info("T%c[0x%03X] %016llX %016llX %016llX %04X %3X %016llX %p%s\n",
336 (!(le64_to_cpu(u0->b) & BIT(29)) ? 'l' :
337 ((le64_to_cpu(u0->b) & BIT(20)) ? 'd' : 'c')),
338 i,
339 (unsigned long long)le64_to_cpu(u0->a),
340 (unsigned long long)le64_to_cpu(u0->b),
341 (unsigned long long)buffer_info->dma,
342 buffer_info->length, buffer_info->next_to_watch,
343 (unsigned long long)buffer_info->time_stamp,
344 buffer_info->skb, next_desc);
345
346 if (netif_msg_pktdata(adapter) && buffer_info->skb)
347 print_hex_dump(KERN_INFO, "", DUMP_PREFIX_ADDRESS,
348 16, 1, buffer_info->skb->data,
349 buffer_info->skb->len, true);
350 }
351
352 /* Print Rx Ring Summary */
353rx_ring_summary:
354 dev_info(&adapter->pdev->dev, "Rx Ring Summary\n");
355 pr_info("Queue [NTU] [NTC]\n");
356 pr_info(" %5d %5X %5X\n",
357 0, rx_ring->next_to_use, rx_ring->next_to_clean);
358
359 /* Print Rx Ring */
360 if (!netif_msg_rx_status(adapter))
361 return;
362
363 dev_info(&adapter->pdev->dev, "Rx Ring Dump\n");
364 switch (adapter->rx_ps_pages) {
365 case 1:
366 case 2:
367 case 3:
368 /* [Extended] Packet Split Receive Descriptor Format
369 *
370 * +-----------------------------------------------------+
371 * 0 | Buffer Address 0 [63:0] |
372 * +-----------------------------------------------------+
373 * 8 | Buffer Address 1 [63:0] |
374 * +-----------------------------------------------------+
375 * 16 | Buffer Address 2 [63:0] |
376 * +-----------------------------------------------------+
377 * 24 | Buffer Address 3 [63:0] |
378 * +-----------------------------------------------------+
379 */
380 pr_info("R [desc] [buffer 0 63:0 ] [buffer 1 63:0 ] [buffer 2 63:0 ] [buffer 3 63:0 ] [bi->dma ] [bi->skb] <-- Ext Pkt Split format\n");
381 /* [Extended] Receive Descriptor (Write-Back) Format
382 *
383 * 63 48 47 32 31 13 12 8 7 4 3 0
384 * +------------------------------------------------------+
385 * 0 | Packet | IP | Rsvd | MRQ | Rsvd | MRQ RSS |
386 * | Checksum | Ident | | Queue | | Type |
387 * +------------------------------------------------------+
388 * 8 | VLAN Tag | Length | Extended Error | Extended Status |
389 * +------------------------------------------------------+
390 * 63 48 47 32 31 20 19 0
391 */
392 pr_info("RWB[desc] [ck ipid mrqhsh] [vl l0 ee es] [ l3 l2 l1 hs] [reserved ] ---------------- [bi->skb] <-- Ext Rx Write-Back format\n");
393 for (i = 0; i < rx_ring->count; i++) {
394 const char *next_desc;
395 buffer_info = &rx_ring->buffer_info[i];
396 rx_desc_ps = E1000_RX_DESC_PS(*rx_ring, i);
397 u1 = (struct my_u1 *)rx_desc_ps;
398 staterr =
399 le32_to_cpu(rx_desc_ps->wb.middle.status_error);
400
401 if (i == rx_ring->next_to_use)
402 next_desc = " NTU";
403 else if (i == rx_ring->next_to_clean)
404 next_desc = " NTC";
405 else
406 next_desc = "";
407
408 if (staterr & E1000_RXD_STAT_DD) {
409 /* Descriptor Done */
410 pr_info("%s[0x%03X] %016llX %016llX %016llX %016llX ---------------- %p%s\n",
411 "RWB", i,
412 (unsigned long long)le64_to_cpu(u1->a),
413 (unsigned long long)le64_to_cpu(u1->b),
414 (unsigned long long)le64_to_cpu(u1->c),
415 (unsigned long long)le64_to_cpu(u1->d),
416 buffer_info->skb, next_desc);
417 } else {
418 pr_info("%s[0x%03X] %016llX %016llX %016llX %016llX %016llX %p%s\n",
419 "R ", i,
420 (unsigned long long)le64_to_cpu(u1->a),
421 (unsigned long long)le64_to_cpu(u1->b),
422 (unsigned long long)le64_to_cpu(u1->c),
423 (unsigned long long)le64_to_cpu(u1->d),
424 (unsigned long long)buffer_info->dma,
425 buffer_info->skb, next_desc);
426
427 if (netif_msg_pktdata(adapter))
428 e1000e_dump_ps_pages(adapter,
429 buffer_info);
430 }
431 }
432 break;
433 default:
434 case 0:
435 /* Extended Receive Descriptor (Read) Format
436 *
437 * +-----------------------------------------------------+
438 * 0 | Buffer Address [63:0] |
439 * +-----------------------------------------------------+
440 * 8 | Reserved |
441 * +-----------------------------------------------------+
442 */
443 pr_info("R [desc] [buf addr 63:0 ] [reserved 63:0 ] [bi->dma ] [bi->skb] <-- Ext (Read) format\n");
444 /* Extended Receive Descriptor (Write-Back) Format
445 *
446 * 63 48 47 32 31 24 23 4 3 0
447 * +------------------------------------------------------+
448 * | RSS Hash | | | |
449 * 0 +-------------------+ Rsvd | Reserved | MRQ RSS |
450 * | Packet | IP | | | Type |
451 * | Checksum | Ident | | | |
452 * +------------------------------------------------------+
453 * 8 | VLAN Tag | Length | Extended Error | Extended Status |
454 * +------------------------------------------------------+
455 * 63 48 47 32 31 20 19 0
456 */
457 pr_info("RWB[desc] [cs ipid mrq] [vt ln xe xs] [bi->skb] <-- Ext (Write-Back) format\n");
458
459 for (i = 0; i < rx_ring->count; i++) {
460 const char *next_desc;
461
462 buffer_info = &rx_ring->buffer_info[i];
463 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i);
464 u1 = (struct my_u1 *)rx_desc;
465 staterr = le32_to_cpu(rx_desc->wb.upper.status_error);
466
467 if (i == rx_ring->next_to_use)
468 next_desc = " NTU";
469 else if (i == rx_ring->next_to_clean)
470 next_desc = " NTC";
471 else
472 next_desc = "";
473
474 if (staterr & E1000_RXD_STAT_DD) {
475 /* Descriptor Done */
476 pr_info("%s[0x%03X] %016llX %016llX ---------------- %p%s\n",
477 "RWB", i,
478 (unsigned long long)le64_to_cpu(u1->a),
479 (unsigned long long)le64_to_cpu(u1->b),
480 buffer_info->skb, next_desc);
481 } else {
482 pr_info("%s[0x%03X] %016llX %016llX %016llX %p%s\n",
483 "R ", i,
484 (unsigned long long)le64_to_cpu(u1->a),
485 (unsigned long long)le64_to_cpu(u1->b),
486 (unsigned long long)buffer_info->dma,
487 buffer_info->skb, next_desc);
488
489 if (netif_msg_pktdata(adapter) &&
490 buffer_info->skb)
491 print_hex_dump(KERN_INFO, "",
492 DUMP_PREFIX_ADDRESS, 16,
493 1,
494 buffer_info->skb->data,
495 adapter->rx_buffer_len,
496 true);
497 }
498 }
499 }
500}
501
502/**
503 * e1000_desc_unused - calculate if we have unused descriptors
504 **/
505static int e1000_desc_unused(struct e1000_ring *ring)
506{
507 if (ring->next_to_clean > ring->next_to_use)
508 return ring->next_to_clean - ring->next_to_use - 1;
509
510 return ring->count + ring->next_to_clean - ring->next_to_use - 1;
511}
512
513/**
514 * e1000e_systim_to_hwtstamp - convert system time value to hw time stamp
515 * @adapter: board private structure
516 * @hwtstamps: time stamp structure to update
517 * @systim: unsigned 64bit system time value.
518 *
519 * Convert the system time value stored in the RX/TXSTMP registers into a
520 * hwtstamp which can be used by the upper level time stamping functions.
521 *
522 * The 'systim_lock' spinlock is used to protect the consistency of the
523 * system time value. This is needed because reading the 64 bit time
524 * value involves reading two 32 bit registers. The first read latches the
525 * value.
526 **/
527static void e1000e_systim_to_hwtstamp(struct e1000_adapter *adapter,
528 struct skb_shared_hwtstamps *hwtstamps,
529 u64 systim)
530{
531 u64 ns;
532 unsigned long flags;
533
534 spin_lock_irqsave(&adapter->systim_lock, flags);
535 ns = timecounter_cyc2time(&adapter->tc, systim);
536 spin_unlock_irqrestore(&adapter->systim_lock, flags);
537
538 memset(hwtstamps, 0, sizeof(*hwtstamps));
539 hwtstamps->hwtstamp = ns_to_ktime(ns);
540}
541
542/**
543 * e1000e_rx_hwtstamp - utility function which checks for Rx time stamp
544 * @adapter: board private structure
545 * @status: descriptor extended error and status field
546 * @skb: particular skb to include time stamp
547 *
548 * If the time stamp is valid, convert it into the timecounter ns value
549 * and store that result into the shhwtstamps structure which is passed
550 * up the network stack.
551 **/
552static void e1000e_rx_hwtstamp(struct e1000_adapter *adapter, u32 status,
553 struct sk_buff *skb)
554{
555 struct e1000_hw *hw = &adapter->hw;
556 u64 rxstmp;
557
558 if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP) ||
559 !(status & E1000_RXDEXT_STATERR_TST) ||
560 !(er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_VALID))
561 return;
562
563 /* The Rx time stamp registers contain the time stamp. No other
564 * received packet will be time stamped until the Rx time stamp
565 * registers are read. Because only one packet can be time stamped
566 * at a time, the register values must belong to this packet and
567 * therefore none of the other additional attributes need to be
568 * compared.
569 */
570 rxstmp = (u64)er32(RXSTMPL);
571 rxstmp |= (u64)er32(RXSTMPH) << 32;
572 e1000e_systim_to_hwtstamp(adapter, skb_hwtstamps(skb), rxstmp);
573
574 adapter->flags2 &= ~FLAG2_CHECK_RX_HWTSTAMP;
575}
576
577/**
578 * e1000_receive_skb - helper function to handle Rx indications
579 * @adapter: board private structure
580 * @staterr: descriptor extended error and status field as written by hardware
581 * @vlan: descriptor vlan field as written by hardware (no le/be conversion)
582 * @skb: pointer to sk_buff to be indicated to stack
583 **/
584static void e1000_receive_skb(struct e1000_adapter *adapter,
585 struct net_device *netdev, struct sk_buff *skb,
586 u32 staterr, __le16 vlan)
587{
588 u16 tag = le16_to_cpu(vlan);
589
590 e1000e_rx_hwtstamp(adapter, staterr, skb);
591
592 skb->protocol = eth_type_trans(skb, netdev);
593
594 if (staterr & E1000_RXD_STAT_VP)
595 __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), tag);
596
597 napi_gro_receive(&adapter->napi, skb);
598}
599
600/**
601 * e1000_rx_checksum - Receive Checksum Offload
602 * @adapter: board private structure
603 * @status_err: receive descriptor status and error fields
604 * @csum: receive descriptor csum field
605 * @sk_buff: socket buffer with received data
606 **/
607static void e1000_rx_checksum(struct e1000_adapter *adapter, u32 status_err,
608 struct sk_buff *skb)
609{
610 u16 status = (u16)status_err;
611 u8 errors = (u8)(status_err >> 24);
612
613 skb_checksum_none_assert(skb);
614
615 /* Rx checksum disabled */
616 if (!(adapter->netdev->features & NETIF_F_RXCSUM))
617 return;
618
619 /* Ignore Checksum bit is set */
620 if (status & E1000_RXD_STAT_IXSM)
621 return;
622
623 /* TCP/UDP checksum error bit or IP checksum error bit is set */
624 if (errors & (E1000_RXD_ERR_TCPE | E1000_RXD_ERR_IPE)) {
625 /* let the stack verify checksum errors */
626 adapter->hw_csum_err++;
627 return;
628 }
629
630 /* TCP/UDP Checksum has not been calculated */
631 if (!(status & (E1000_RXD_STAT_TCPCS | E1000_RXD_STAT_UDPCS)))
632 return;
633
634 /* It must be a TCP or UDP packet with a valid checksum */
635 skb->ip_summed = CHECKSUM_UNNECESSARY;
636 adapter->hw_csum_good++;
637}
638
639static void e1000e_update_rdt_wa(struct e1000_ring *rx_ring, unsigned int i)
640{
641 struct e1000_adapter *adapter = rx_ring->adapter;
642 struct e1000_hw *hw = &adapter->hw;
643
644 __ew32_prepare(hw);
645 writel(i, rx_ring->tail);
646
647 if (unlikely(i != readl(rx_ring->tail))) {
648 u32 rctl = er32(RCTL);
649
650 ew32(RCTL, rctl & ~E1000_RCTL_EN);
651 e_err("ME firmware caused invalid RDT - resetting\n");
652 schedule_work(&adapter->reset_task);
653 }
654}
655
656static void e1000e_update_tdt_wa(struct e1000_ring *tx_ring, unsigned int i)
657{
658 struct e1000_adapter *adapter = tx_ring->adapter;
659 struct e1000_hw *hw = &adapter->hw;
660
661 __ew32_prepare(hw);
662 writel(i, tx_ring->tail);
663
664 if (unlikely(i != readl(tx_ring->tail))) {
665 u32 tctl = er32(TCTL);
666
667 ew32(TCTL, tctl & ~E1000_TCTL_EN);
668 e_err("ME firmware caused invalid TDT - resetting\n");
669 schedule_work(&adapter->reset_task);
670 }
671}
672
673/**
674 * e1000_alloc_rx_buffers - Replace used receive buffers
675 * @rx_ring: Rx descriptor ring
676 **/
677static void e1000_alloc_rx_buffers(struct e1000_ring *rx_ring,
678 int cleaned_count, gfp_t gfp)
679{
680 struct e1000_adapter *adapter = rx_ring->adapter;
681 struct net_device *netdev = adapter->netdev;
682 struct pci_dev *pdev = adapter->pdev;
683 union e1000_rx_desc_extended *rx_desc;
684 struct e1000_buffer *buffer_info;
685 struct sk_buff *skb;
686 unsigned int i;
687 unsigned int bufsz = adapter->rx_buffer_len;
688
689 i = rx_ring->next_to_use;
690 buffer_info = &rx_ring->buffer_info[i];
691
692 while (cleaned_count--) {
693 skb = buffer_info->skb;
694 if (skb) {
695 skb_trim(skb, 0);
696 goto map_skb;
697 }
698
699 skb = __netdev_alloc_skb_ip_align(netdev, bufsz, gfp);
700 if (!skb) {
701 /* Better luck next round */
702 adapter->alloc_rx_buff_failed++;
703 break;
704 }
705
706 buffer_info->skb = skb;
707map_skb:
708 buffer_info->dma = dma_map_single(&pdev->dev, skb->data,
709 adapter->rx_buffer_len,
710 DMA_FROM_DEVICE);
711 if (dma_mapping_error(&pdev->dev, buffer_info->dma)) {
712 dev_err(&pdev->dev, "Rx DMA map failed\n");
713 adapter->rx_dma_failed++;
714 break;
715 }
716
717 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i);
718 rx_desc->read.buffer_addr = cpu_to_le64(buffer_info->dma);
719
720 if (unlikely(!(i & (E1000_RX_BUFFER_WRITE - 1)))) {
721 /* Force memory writes to complete before letting h/w
722 * know there are new descriptors to fetch. (Only
723 * applicable for weak-ordered memory model archs,
724 * such as IA-64).
725 */
726 wmb();
727 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA)
728 e1000e_update_rdt_wa(rx_ring, i);
729 else
730 writel(i, rx_ring->tail);
731 }
732 i++;
733 if (i == rx_ring->count)
734 i = 0;
735 buffer_info = &rx_ring->buffer_info[i];
736 }
737
738 rx_ring->next_to_use = i;
739}
740
741/**
742 * e1000_alloc_rx_buffers_ps - Replace used receive buffers; packet split
743 * @rx_ring: Rx descriptor ring
744 **/
745static void e1000_alloc_rx_buffers_ps(struct e1000_ring *rx_ring,
746 int cleaned_count, gfp_t gfp)
747{
748 struct e1000_adapter *adapter = rx_ring->adapter;
749 struct net_device *netdev = adapter->netdev;
750 struct pci_dev *pdev = adapter->pdev;
751 union e1000_rx_desc_packet_split *rx_desc;
752 struct e1000_buffer *buffer_info;
753 struct e1000_ps_page *ps_page;
754 struct sk_buff *skb;
755 unsigned int i, j;
756
757 i = rx_ring->next_to_use;
758 buffer_info = &rx_ring->buffer_info[i];
759
760 while (cleaned_count--) {
761 rx_desc = E1000_RX_DESC_PS(*rx_ring, i);
762
763 for (j = 0; j < PS_PAGE_BUFFERS; j++) {
764 ps_page = &buffer_info->ps_pages[j];
765 if (j >= adapter->rx_ps_pages) {
766 /* all unused desc entries get hw null ptr */
767 rx_desc->read.buffer_addr[j + 1] =
768 ~cpu_to_le64(0);
769 continue;
770 }
771 if (!ps_page->page) {
772 ps_page->page = alloc_page(gfp);
773 if (!ps_page->page) {
774 adapter->alloc_rx_buff_failed++;
775 goto no_buffers;
776 }
777 ps_page->dma = dma_map_page(&pdev->dev,
778 ps_page->page,
779 0, PAGE_SIZE,
780 DMA_FROM_DEVICE);
781 if (dma_mapping_error(&pdev->dev,
782 ps_page->dma)) {
783 dev_err(&adapter->pdev->dev,
784 "Rx DMA page map failed\n");
785 adapter->rx_dma_failed++;
786 goto no_buffers;
787 }
788 }
789 /* Refresh the desc even if buffer_addrs
790 * didn't change because each write-back
791 * erases this info.
792 */
793 rx_desc->read.buffer_addr[j + 1] =
794 cpu_to_le64(ps_page->dma);
795 }
796
797 skb = __netdev_alloc_skb_ip_align(netdev, adapter->rx_ps_bsize0,
798 gfp);
799
800 if (!skb) {
801 adapter->alloc_rx_buff_failed++;
802 break;
803 }
804
805 buffer_info->skb = skb;
806 buffer_info->dma = dma_map_single(&pdev->dev, skb->data,
807 adapter->rx_ps_bsize0,
808 DMA_FROM_DEVICE);
809 if (dma_mapping_error(&pdev->dev, buffer_info->dma)) {
810 dev_err(&pdev->dev, "Rx DMA map failed\n");
811 adapter->rx_dma_failed++;
812 /* cleanup skb */
813 dev_kfree_skb_any(skb);
814 buffer_info->skb = NULL;
815 break;
816 }
817
818 rx_desc->read.buffer_addr[0] = cpu_to_le64(buffer_info->dma);
819
820 if (unlikely(!(i & (E1000_RX_BUFFER_WRITE - 1)))) {
821 /* Force memory writes to complete before letting h/w
822 * know there are new descriptors to fetch. (Only
823 * applicable for weak-ordered memory model archs,
824 * such as IA-64).
825 */
826 wmb();
827 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA)
828 e1000e_update_rdt_wa(rx_ring, i << 1);
829 else
830 writel(i << 1, rx_ring->tail);
831 }
832
833 i++;
834 if (i == rx_ring->count)
835 i = 0;
836 buffer_info = &rx_ring->buffer_info[i];
837 }
838
839no_buffers:
840 rx_ring->next_to_use = i;
841}
842
843/**
844 * e1000_alloc_jumbo_rx_buffers - Replace used jumbo receive buffers
845 * @rx_ring: Rx descriptor ring
846 * @cleaned_count: number of buffers to allocate this pass
847 **/
848
849static void e1000_alloc_jumbo_rx_buffers(struct e1000_ring *rx_ring,
850 int cleaned_count, gfp_t gfp)
851{
852 struct e1000_adapter *adapter = rx_ring->adapter;
853 struct net_device *netdev = adapter->netdev;
854 struct pci_dev *pdev = adapter->pdev;
855 union e1000_rx_desc_extended *rx_desc;
856 struct e1000_buffer *buffer_info;
857 struct sk_buff *skb;
858 unsigned int i;
859 unsigned int bufsz = 256 - 16; /* for skb_reserve */
860
861 i = rx_ring->next_to_use;
862 buffer_info = &rx_ring->buffer_info[i];
863
864 while (cleaned_count--) {
865 skb = buffer_info->skb;
866 if (skb) {
867 skb_trim(skb, 0);
868 goto check_page;
869 }
870
871 skb = __netdev_alloc_skb_ip_align(netdev, bufsz, gfp);
872 if (unlikely(!skb)) {
873 /* Better luck next round */
874 adapter->alloc_rx_buff_failed++;
875 break;
876 }
877
878 buffer_info->skb = skb;
879check_page:
880 /* allocate a new page if necessary */
881 if (!buffer_info->page) {
882 buffer_info->page = alloc_page(gfp);
883 if (unlikely(!buffer_info->page)) {
884 adapter->alloc_rx_buff_failed++;
885 break;
886 }
887 }
888
889 if (!buffer_info->dma) {
890 buffer_info->dma = dma_map_page(&pdev->dev,
891 buffer_info->page, 0,
892 PAGE_SIZE,
893 DMA_FROM_DEVICE);
894 if (dma_mapping_error(&pdev->dev, buffer_info->dma)) {
895 adapter->alloc_rx_buff_failed++;
896 break;
897 }
898 }
899
900 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i);
901 rx_desc->read.buffer_addr = cpu_to_le64(buffer_info->dma);
902
903 if (unlikely(++i == rx_ring->count))
904 i = 0;
905 buffer_info = &rx_ring->buffer_info[i];
906 }
907
908 if (likely(rx_ring->next_to_use != i)) {
909 rx_ring->next_to_use = i;
910 if (unlikely(i-- == 0))
911 i = (rx_ring->count - 1);
912
913 /* Force memory writes to complete before letting h/w
914 * know there are new descriptors to fetch. (Only
915 * applicable for weak-ordered memory model archs,
916 * such as IA-64).
917 */
918 wmb();
919 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA)
920 e1000e_update_rdt_wa(rx_ring, i);
921 else
922 writel(i, rx_ring->tail);
923 }
924}
925
926static inline void e1000_rx_hash(struct net_device *netdev, __le32 rss,
927 struct sk_buff *skb)
928{
929 if (netdev->features & NETIF_F_RXHASH)
930 skb_set_hash(skb, le32_to_cpu(rss), PKT_HASH_TYPE_L3);
931}
932
933/**
934 * e1000_clean_rx_irq - Send received data up the network stack
935 * @rx_ring: Rx descriptor ring
936 *
937 * the return value indicates whether actual cleaning was done, there
938 * is no guarantee that everything was cleaned
939 **/
940static bool e1000_clean_rx_irq(struct e1000_ring *rx_ring, int *work_done,
941 int work_to_do)
942{
943 struct e1000_adapter *adapter = rx_ring->adapter;
944 struct net_device *netdev = adapter->netdev;
945 struct pci_dev *pdev = adapter->pdev;
946 struct e1000_hw *hw = &adapter->hw;
947 union e1000_rx_desc_extended *rx_desc, *next_rxd;
948 struct e1000_buffer *buffer_info, *next_buffer;
949 u32 length, staterr;
950 unsigned int i;
951 int cleaned_count = 0;
952 bool cleaned = false;
953 unsigned int total_rx_bytes = 0, total_rx_packets = 0;
954
955 i = rx_ring->next_to_clean;
956 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i);
957 staterr = le32_to_cpu(rx_desc->wb.upper.status_error);
958 buffer_info = &rx_ring->buffer_info[i];
959
960 while (staterr & E1000_RXD_STAT_DD) {
961 struct sk_buff *skb;
962
963 if (*work_done >= work_to_do)
964 break;
965 (*work_done)++;
966 dma_rmb(); /* read descriptor and rx_buffer_info after status DD */
967
968 skb = buffer_info->skb;
969 buffer_info->skb = NULL;
970
971 prefetch(skb->data - NET_IP_ALIGN);
972
973 i++;
974 if (i == rx_ring->count)
975 i = 0;
976 next_rxd = E1000_RX_DESC_EXT(*rx_ring, i);
977 prefetch(next_rxd);
978
979 next_buffer = &rx_ring->buffer_info[i];
980
981 cleaned = true;
982 cleaned_count++;
983 dma_unmap_single(&pdev->dev, buffer_info->dma,
984 adapter->rx_buffer_len, DMA_FROM_DEVICE);
985 buffer_info->dma = 0;
986
987 length = le16_to_cpu(rx_desc->wb.upper.length);
988
989 /* !EOP means multiple descriptors were used to store a single
990 * packet, if that's the case we need to toss it. In fact, we
991 * need to toss every packet with the EOP bit clear and the
992 * next frame that _does_ have the EOP bit set, as it is by
993 * definition only a frame fragment
994 */
995 if (unlikely(!(staterr & E1000_RXD_STAT_EOP)))
996 adapter->flags2 |= FLAG2_IS_DISCARDING;
997
998 if (adapter->flags2 & FLAG2_IS_DISCARDING) {
999 /* All receives must fit into a single buffer */
1000 e_dbg("Receive packet consumed multiple buffers\n");
1001 /* recycle */
1002 buffer_info->skb = skb;
1003 if (staterr & E1000_RXD_STAT_EOP)
1004 adapter->flags2 &= ~FLAG2_IS_DISCARDING;
1005 goto next_desc;
1006 }
1007
1008 if (unlikely((staterr & E1000_RXDEXT_ERR_FRAME_ERR_MASK) &&
1009 !(netdev->features & NETIF_F_RXALL))) {
1010 /* recycle */
1011 buffer_info->skb = skb;
1012 goto next_desc;
1013 }
1014
1015 /* adjust length to remove Ethernet CRC */
1016 if (!(adapter->flags2 & FLAG2_CRC_STRIPPING)) {
1017 /* If configured to store CRC, don't subtract FCS,
1018 * but keep the FCS bytes out of the total_rx_bytes
1019 * counter
1020 */
1021 if (netdev->features & NETIF_F_RXFCS)
1022 total_rx_bytes -= 4;
1023 else
1024 length -= 4;
1025 }
1026
1027 total_rx_bytes += length;
1028 total_rx_packets++;
1029
1030 /* code added for copybreak, this should improve
1031 * performance for small packets with large amounts
1032 * of reassembly being done in the stack
1033 */
1034 if (length < copybreak) {
1035 struct sk_buff *new_skb =
1036 napi_alloc_skb(&adapter->napi, length);
1037 if (new_skb) {
1038 skb_copy_to_linear_data_offset(new_skb,
1039 -NET_IP_ALIGN,
1040 (skb->data -
1041 NET_IP_ALIGN),
1042 (length +
1043 NET_IP_ALIGN));
1044 /* save the skb in buffer_info as good */
1045 buffer_info->skb = skb;
1046 skb = new_skb;
1047 }
1048 /* else just continue with the old one */
1049 }
1050 /* end copybreak code */
1051 skb_put(skb, length);
1052
1053 /* Receive Checksum Offload */
1054 e1000_rx_checksum(adapter, staterr, skb);
1055
1056 e1000_rx_hash(netdev, rx_desc->wb.lower.hi_dword.rss, skb);
1057
1058 e1000_receive_skb(adapter, netdev, skb, staterr,
1059 rx_desc->wb.upper.vlan);
1060
1061next_desc:
1062 rx_desc->wb.upper.status_error &= cpu_to_le32(~0xFF);
1063
1064 /* return some buffers to hardware, one at a time is too slow */
1065 if (cleaned_count >= E1000_RX_BUFFER_WRITE) {
1066 adapter->alloc_rx_buf(rx_ring, cleaned_count,
1067 GFP_ATOMIC);
1068 cleaned_count = 0;
1069 }
1070
1071 /* use prefetched values */
1072 rx_desc = next_rxd;
1073 buffer_info = next_buffer;
1074
1075 staterr = le32_to_cpu(rx_desc->wb.upper.status_error);
1076 }
1077 rx_ring->next_to_clean = i;
1078
1079 cleaned_count = e1000_desc_unused(rx_ring);
1080 if (cleaned_count)
1081 adapter->alloc_rx_buf(rx_ring, cleaned_count, GFP_ATOMIC);
1082
1083 adapter->total_rx_bytes += total_rx_bytes;
1084 adapter->total_rx_packets += total_rx_packets;
1085 return cleaned;
1086}
1087
1088static void e1000_put_txbuf(struct e1000_ring *tx_ring,
1089 struct e1000_buffer *buffer_info,
1090 bool drop)
1091{
1092 struct e1000_adapter *adapter = tx_ring->adapter;
1093
1094 if (buffer_info->dma) {
1095 if (buffer_info->mapped_as_page)
1096 dma_unmap_page(&adapter->pdev->dev, buffer_info->dma,
1097 buffer_info->length, DMA_TO_DEVICE);
1098 else
1099 dma_unmap_single(&adapter->pdev->dev, buffer_info->dma,
1100 buffer_info->length, DMA_TO_DEVICE);
1101 buffer_info->dma = 0;
1102 }
1103 if (buffer_info->skb) {
1104 if (drop)
1105 dev_kfree_skb_any(buffer_info->skb);
1106 else
1107 dev_consume_skb_any(buffer_info->skb);
1108 buffer_info->skb = NULL;
1109 }
1110 buffer_info->time_stamp = 0;
1111}
1112
1113static void e1000_print_hw_hang(struct work_struct *work)
1114{
1115 struct e1000_adapter *adapter = container_of(work,
1116 struct e1000_adapter,
1117 print_hang_task);
1118 struct net_device *netdev = adapter->netdev;
1119 struct e1000_ring *tx_ring = adapter->tx_ring;
1120 unsigned int i = tx_ring->next_to_clean;
1121 unsigned int eop = tx_ring->buffer_info[i].next_to_watch;
1122 struct e1000_tx_desc *eop_desc = E1000_TX_DESC(*tx_ring, eop);
1123 struct e1000_hw *hw = &adapter->hw;
1124 u16 phy_status, phy_1000t_status, phy_ext_status;
1125 u16 pci_status;
1126
1127 if (test_bit(__E1000_DOWN, &adapter->state))
1128 return;
1129
1130 if (!adapter->tx_hang_recheck && (adapter->flags2 & FLAG2_DMA_BURST)) {
1131 /* May be block on write-back, flush and detect again
1132 * flush pending descriptor writebacks to memory
1133 */
1134 ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD);
1135 /* execute the writes immediately */
1136 e1e_flush();
1137 /* Due to rare timing issues, write to TIDV again to ensure
1138 * the write is successful
1139 */
1140 ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD);
1141 /* execute the writes immediately */
1142 e1e_flush();
1143 adapter->tx_hang_recheck = true;
1144 return;
1145 }
1146 adapter->tx_hang_recheck = false;
1147
1148 if (er32(TDH(0)) == er32(TDT(0))) {
1149 e_dbg("false hang detected, ignoring\n");
1150 return;
1151 }
1152
1153 /* Real hang detected */
1154 netif_stop_queue(netdev);
1155
1156 e1e_rphy(hw, MII_BMSR, &phy_status);
1157 e1e_rphy(hw, MII_STAT1000, &phy_1000t_status);
1158 e1e_rphy(hw, MII_ESTATUS, &phy_ext_status);
1159
1160 pci_read_config_word(adapter->pdev, PCI_STATUS, &pci_status);
1161
1162 /* detected Hardware unit hang */
1163 e_err("Detected Hardware Unit Hang:\n"
1164 " TDH <%x>\n"
1165 " TDT <%x>\n"
1166 " next_to_use <%x>\n"
1167 " next_to_clean <%x>\n"
1168 "buffer_info[next_to_clean]:\n"
1169 " time_stamp <%lx>\n"
1170 " next_to_watch <%x>\n"
1171 " jiffies <%lx>\n"
1172 " next_to_watch.status <%x>\n"
1173 "MAC Status <%x>\n"
1174 "PHY Status <%x>\n"
1175 "PHY 1000BASE-T Status <%x>\n"
1176 "PHY Extended Status <%x>\n"
1177 "PCI Status <%x>\n",
1178 readl(tx_ring->head), readl(tx_ring->tail), tx_ring->next_to_use,
1179 tx_ring->next_to_clean, tx_ring->buffer_info[eop].time_stamp,
1180 eop, jiffies, eop_desc->upper.fields.status, er32(STATUS),
1181 phy_status, phy_1000t_status, phy_ext_status, pci_status);
1182
1183 e1000e_dump(adapter);
1184
1185 /* Suggest workaround for known h/w issue */
1186 if ((hw->mac.type == e1000_pchlan) && (er32(CTRL) & E1000_CTRL_TFCE))
1187 e_err("Try turning off Tx pause (flow control) via ethtool\n");
1188}
1189
1190/**
1191 * e1000e_tx_hwtstamp_work - check for Tx time stamp
1192 * @work: pointer to work struct
1193 *
1194 * This work function polls the TSYNCTXCTL valid bit to determine when a
1195 * timestamp has been taken for the current stored skb. The timestamp must
1196 * be for this skb because only one such packet is allowed in the queue.
1197 */
1198static void e1000e_tx_hwtstamp_work(struct work_struct *work)
1199{
1200 struct e1000_adapter *adapter = container_of(work, struct e1000_adapter,
1201 tx_hwtstamp_work);
1202 struct e1000_hw *hw = &adapter->hw;
1203
1204 if (er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_VALID) {
1205 struct sk_buff *skb = adapter->tx_hwtstamp_skb;
1206 struct skb_shared_hwtstamps shhwtstamps;
1207 u64 txstmp;
1208
1209 txstmp = er32(TXSTMPL);
1210 txstmp |= (u64)er32(TXSTMPH) << 32;
1211
1212 e1000e_systim_to_hwtstamp(adapter, &shhwtstamps, txstmp);
1213
1214 /* Clear the global tx_hwtstamp_skb pointer and force writes
1215 * prior to notifying the stack of a Tx timestamp.
1216 */
1217 adapter->tx_hwtstamp_skb = NULL;
1218 wmb(); /* force write prior to skb_tstamp_tx */
1219
1220 skb_tstamp_tx(skb, &shhwtstamps);
1221 dev_consume_skb_any(skb);
1222 } else if (time_after(jiffies, adapter->tx_hwtstamp_start
1223 + adapter->tx_timeout_factor * HZ)) {
1224 dev_kfree_skb_any(adapter->tx_hwtstamp_skb);
1225 adapter->tx_hwtstamp_skb = NULL;
1226 adapter->tx_hwtstamp_timeouts++;
1227 e_warn("clearing Tx timestamp hang\n");
1228 } else {
1229 /* reschedule to check later */
1230 schedule_work(&adapter->tx_hwtstamp_work);
1231 }
1232}
1233
1234/**
1235 * e1000_clean_tx_irq - Reclaim resources after transmit completes
1236 * @tx_ring: Tx descriptor ring
1237 *
1238 * the return value indicates whether actual cleaning was done, there
1239 * is no guarantee that everything was cleaned
1240 **/
1241static bool e1000_clean_tx_irq(struct e1000_ring *tx_ring)
1242{
1243 struct e1000_adapter *adapter = tx_ring->adapter;
1244 struct net_device *netdev = adapter->netdev;
1245 struct e1000_hw *hw = &adapter->hw;
1246 struct e1000_tx_desc *tx_desc, *eop_desc;
1247 struct e1000_buffer *buffer_info;
1248 unsigned int i, eop;
1249 unsigned int count = 0;
1250 unsigned int total_tx_bytes = 0, total_tx_packets = 0;
1251 unsigned int bytes_compl = 0, pkts_compl = 0;
1252
1253 i = tx_ring->next_to_clean;
1254 eop = tx_ring->buffer_info[i].next_to_watch;
1255 eop_desc = E1000_TX_DESC(*tx_ring, eop);
1256
1257 while ((eop_desc->upper.data & cpu_to_le32(E1000_TXD_STAT_DD)) &&
1258 (count < tx_ring->count)) {
1259 bool cleaned = false;
1260
1261 dma_rmb(); /* read buffer_info after eop_desc */
1262 for (; !cleaned; count++) {
1263 tx_desc = E1000_TX_DESC(*tx_ring, i);
1264 buffer_info = &tx_ring->buffer_info[i];
1265 cleaned = (i == eop);
1266
1267 if (cleaned) {
1268 total_tx_packets += buffer_info->segs;
1269 total_tx_bytes += buffer_info->bytecount;
1270 if (buffer_info->skb) {
1271 bytes_compl += buffer_info->skb->len;
1272 pkts_compl++;
1273 }
1274 }
1275
1276 e1000_put_txbuf(tx_ring, buffer_info, false);
1277 tx_desc->upper.data = 0;
1278
1279 i++;
1280 if (i == tx_ring->count)
1281 i = 0;
1282 }
1283
1284 if (i == tx_ring->next_to_use)
1285 break;
1286 eop = tx_ring->buffer_info[i].next_to_watch;
1287 eop_desc = E1000_TX_DESC(*tx_ring, eop);
1288 }
1289
1290 tx_ring->next_to_clean = i;
1291
1292 netdev_completed_queue(netdev, pkts_compl, bytes_compl);
1293
1294#define TX_WAKE_THRESHOLD 32
1295 if (count && netif_carrier_ok(netdev) &&
1296 e1000_desc_unused(tx_ring) >= TX_WAKE_THRESHOLD) {
1297 /* Make sure that anybody stopping the queue after this
1298 * sees the new next_to_clean.
1299 */
1300 smp_mb();
1301
1302 if (netif_queue_stopped(netdev) &&
1303 !(test_bit(__E1000_DOWN, &adapter->state))) {
1304 netif_wake_queue(netdev);
1305 ++adapter->restart_queue;
1306 }
1307 }
1308
1309 if (adapter->detect_tx_hung) {
1310 /* Detect a transmit hang in hardware, this serializes the
1311 * check with the clearing of time_stamp and movement of i
1312 */
1313 adapter->detect_tx_hung = false;
1314 if (tx_ring->buffer_info[i].time_stamp &&
1315 time_after(jiffies, tx_ring->buffer_info[i].time_stamp
1316 + (adapter->tx_timeout_factor * HZ)) &&
1317 !(er32(STATUS) & E1000_STATUS_TXOFF))
1318 schedule_work(&adapter->print_hang_task);
1319 else
1320 adapter->tx_hang_recheck = false;
1321 }
1322 adapter->total_tx_bytes += total_tx_bytes;
1323 adapter->total_tx_packets += total_tx_packets;
1324 return count < tx_ring->count;
1325}
1326
1327/**
1328 * e1000_clean_rx_irq_ps - Send received data up the network stack; packet split
1329 * @rx_ring: Rx descriptor ring
1330 *
1331 * the return value indicates whether actual cleaning was done, there
1332 * is no guarantee that everything was cleaned
1333 **/
1334static bool e1000_clean_rx_irq_ps(struct e1000_ring *rx_ring, int *work_done,
1335 int work_to_do)
1336{
1337 struct e1000_adapter *adapter = rx_ring->adapter;
1338 struct e1000_hw *hw = &adapter->hw;
1339 union e1000_rx_desc_packet_split *rx_desc, *next_rxd;
1340 struct net_device *netdev = adapter->netdev;
1341 struct pci_dev *pdev = adapter->pdev;
1342 struct e1000_buffer *buffer_info, *next_buffer;
1343 struct e1000_ps_page *ps_page;
1344 struct sk_buff *skb;
1345 unsigned int i, j;
1346 u32 length, staterr;
1347 int cleaned_count = 0;
1348 bool cleaned = false;
1349 unsigned int total_rx_bytes = 0, total_rx_packets = 0;
1350
1351 i = rx_ring->next_to_clean;
1352 rx_desc = E1000_RX_DESC_PS(*rx_ring, i);
1353 staterr = le32_to_cpu(rx_desc->wb.middle.status_error);
1354 buffer_info = &rx_ring->buffer_info[i];
1355
1356 while (staterr & E1000_RXD_STAT_DD) {
1357 if (*work_done >= work_to_do)
1358 break;
1359 (*work_done)++;
1360 skb = buffer_info->skb;
1361 dma_rmb(); /* read descriptor and rx_buffer_info after status DD */
1362
1363 /* in the packet split case this is header only */
1364 prefetch(skb->data - NET_IP_ALIGN);
1365
1366 i++;
1367 if (i == rx_ring->count)
1368 i = 0;
1369 next_rxd = E1000_RX_DESC_PS(*rx_ring, i);
1370 prefetch(next_rxd);
1371
1372 next_buffer = &rx_ring->buffer_info[i];
1373
1374 cleaned = true;
1375 cleaned_count++;
1376 dma_unmap_single(&pdev->dev, buffer_info->dma,
1377 adapter->rx_ps_bsize0, DMA_FROM_DEVICE);
1378 buffer_info->dma = 0;
1379
1380 /* see !EOP comment in other Rx routine */
1381 if (!(staterr & E1000_RXD_STAT_EOP))
1382 adapter->flags2 |= FLAG2_IS_DISCARDING;
1383
1384 if (adapter->flags2 & FLAG2_IS_DISCARDING) {
1385 e_dbg("Packet Split buffers didn't pick up the full packet\n");
1386 dev_kfree_skb_irq(skb);
1387 if (staterr & E1000_RXD_STAT_EOP)
1388 adapter->flags2 &= ~FLAG2_IS_DISCARDING;
1389 goto next_desc;
1390 }
1391
1392 if (unlikely((staterr & E1000_RXDEXT_ERR_FRAME_ERR_MASK) &&
1393 !(netdev->features & NETIF_F_RXALL))) {
1394 dev_kfree_skb_irq(skb);
1395 goto next_desc;
1396 }
1397
1398 length = le16_to_cpu(rx_desc->wb.middle.length0);
1399
1400 if (!length) {
1401 e_dbg("Last part of the packet spanning multiple descriptors\n");
1402 dev_kfree_skb_irq(skb);
1403 goto next_desc;
1404 }
1405
1406 /* Good Receive */
1407 skb_put(skb, length);
1408
1409 {
1410 /* this looks ugly, but it seems compiler issues make
1411 * it more efficient than reusing j
1412 */
1413 int l1 = le16_to_cpu(rx_desc->wb.upper.length[0]);
1414
1415 /* page alloc/put takes too long and effects small
1416 * packet throughput, so unsplit small packets and
1417 * save the alloc/put only valid in softirq (napi)
1418 * context to call kmap_*
1419 */
1420 if (l1 && (l1 <= copybreak) &&
1421 ((length + l1) <= adapter->rx_ps_bsize0)) {
1422 u8 *vaddr;
1423
1424 ps_page = &buffer_info->ps_pages[0];
1425
1426 /* there is no documentation about how to call
1427 * kmap_atomic, so we can't hold the mapping
1428 * very long
1429 */
1430 dma_sync_single_for_cpu(&pdev->dev,
1431 ps_page->dma,
1432 PAGE_SIZE,
1433 DMA_FROM_DEVICE);
1434 vaddr = kmap_atomic(ps_page->page);
1435 memcpy(skb_tail_pointer(skb), vaddr, l1);
1436 kunmap_atomic(vaddr);
1437 dma_sync_single_for_device(&pdev->dev,
1438 ps_page->dma,
1439 PAGE_SIZE,
1440 DMA_FROM_DEVICE);
1441
1442 /* remove the CRC */
1443 if (!(adapter->flags2 & FLAG2_CRC_STRIPPING)) {
1444 if (!(netdev->features & NETIF_F_RXFCS))
1445 l1 -= 4;
1446 }
1447
1448 skb_put(skb, l1);
1449 goto copydone;
1450 } /* if */
1451 }
1452
1453 for (j = 0; j < PS_PAGE_BUFFERS; j++) {
1454 length = le16_to_cpu(rx_desc->wb.upper.length[j]);
1455 if (!length)
1456 break;
1457
1458 ps_page = &buffer_info->ps_pages[j];
1459 dma_unmap_page(&pdev->dev, ps_page->dma, PAGE_SIZE,
1460 DMA_FROM_DEVICE);
1461 ps_page->dma = 0;
1462 skb_fill_page_desc(skb, j, ps_page->page, 0, length);
1463 ps_page->page = NULL;
1464 skb->len += length;
1465 skb->data_len += length;
1466 skb->truesize += PAGE_SIZE;
1467 }
1468
1469 /* strip the ethernet crc, problem is we're using pages now so
1470 * this whole operation can get a little cpu intensive
1471 */
1472 if (!(adapter->flags2 & FLAG2_CRC_STRIPPING)) {
1473 if (!(netdev->features & NETIF_F_RXFCS))
1474 pskb_trim(skb, skb->len - 4);
1475 }
1476
1477copydone:
1478 total_rx_bytes += skb->len;
1479 total_rx_packets++;
1480
1481 e1000_rx_checksum(adapter, staterr, skb);
1482
1483 e1000_rx_hash(netdev, rx_desc->wb.lower.hi_dword.rss, skb);
1484
1485 if (rx_desc->wb.upper.header_status &
1486 cpu_to_le16(E1000_RXDPS_HDRSTAT_HDRSP))
1487 adapter->rx_hdr_split++;
1488
1489 e1000_receive_skb(adapter, netdev, skb, staterr,
1490 rx_desc->wb.middle.vlan);
1491
1492next_desc:
1493 rx_desc->wb.middle.status_error &= cpu_to_le32(~0xFF);
1494 buffer_info->skb = NULL;
1495
1496 /* return some buffers to hardware, one at a time is too slow */
1497 if (cleaned_count >= E1000_RX_BUFFER_WRITE) {
1498 adapter->alloc_rx_buf(rx_ring, cleaned_count,
1499 GFP_ATOMIC);
1500 cleaned_count = 0;
1501 }
1502
1503 /* use prefetched values */
1504 rx_desc = next_rxd;
1505 buffer_info = next_buffer;
1506
1507 staterr = le32_to_cpu(rx_desc->wb.middle.status_error);
1508 }
1509 rx_ring->next_to_clean = i;
1510
1511 cleaned_count = e1000_desc_unused(rx_ring);
1512 if (cleaned_count)
1513 adapter->alloc_rx_buf(rx_ring, cleaned_count, GFP_ATOMIC);
1514
1515 adapter->total_rx_bytes += total_rx_bytes;
1516 adapter->total_rx_packets += total_rx_packets;
1517 return cleaned;
1518}
1519
1520/**
1521 * e1000_consume_page - helper function
1522 **/
1523static void e1000_consume_page(struct e1000_buffer *bi, struct sk_buff *skb,
1524 u16 length)
1525{
1526 bi->page = NULL;
1527 skb->len += length;
1528 skb->data_len += length;
1529 skb->truesize += PAGE_SIZE;
1530}
1531
1532/**
1533 * e1000_clean_jumbo_rx_irq - Send received data up the network stack; legacy
1534 * @adapter: board private structure
1535 *
1536 * the return value indicates whether actual cleaning was done, there
1537 * is no guarantee that everything was cleaned
1538 **/
1539static bool e1000_clean_jumbo_rx_irq(struct e1000_ring *rx_ring, int *work_done,
1540 int work_to_do)
1541{
1542 struct e1000_adapter *adapter = rx_ring->adapter;
1543 struct net_device *netdev = adapter->netdev;
1544 struct pci_dev *pdev = adapter->pdev;
1545 union e1000_rx_desc_extended *rx_desc, *next_rxd;
1546 struct e1000_buffer *buffer_info, *next_buffer;
1547 u32 length, staterr;
1548 unsigned int i;
1549 int cleaned_count = 0;
1550 bool cleaned = false;
1551 unsigned int total_rx_bytes = 0, total_rx_packets = 0;
1552 struct skb_shared_info *shinfo;
1553
1554 i = rx_ring->next_to_clean;
1555 rx_desc = E1000_RX_DESC_EXT(*rx_ring, i);
1556 staterr = le32_to_cpu(rx_desc->wb.upper.status_error);
1557 buffer_info = &rx_ring->buffer_info[i];
1558
1559 while (staterr & E1000_RXD_STAT_DD) {
1560 struct sk_buff *skb;
1561
1562 if (*work_done >= work_to_do)
1563 break;
1564 (*work_done)++;
1565 dma_rmb(); /* read descriptor and rx_buffer_info after status DD */
1566
1567 skb = buffer_info->skb;
1568 buffer_info->skb = NULL;
1569
1570 ++i;
1571 if (i == rx_ring->count)
1572 i = 0;
1573 next_rxd = E1000_RX_DESC_EXT(*rx_ring, i);
1574 prefetch(next_rxd);
1575
1576 next_buffer = &rx_ring->buffer_info[i];
1577
1578 cleaned = true;
1579 cleaned_count++;
1580 dma_unmap_page(&pdev->dev, buffer_info->dma, PAGE_SIZE,
1581 DMA_FROM_DEVICE);
1582 buffer_info->dma = 0;
1583
1584 length = le16_to_cpu(rx_desc->wb.upper.length);
1585
1586 /* errors is only valid for DD + EOP descriptors */
1587 if (unlikely((staterr & E1000_RXD_STAT_EOP) &&
1588 ((staterr & E1000_RXDEXT_ERR_FRAME_ERR_MASK) &&
1589 !(netdev->features & NETIF_F_RXALL)))) {
1590 /* recycle both page and skb */
1591 buffer_info->skb = skb;
1592 /* an error means any chain goes out the window too */
1593 if (rx_ring->rx_skb_top)
1594 dev_kfree_skb_irq(rx_ring->rx_skb_top);
1595 rx_ring->rx_skb_top = NULL;
1596 goto next_desc;
1597 }
1598#define rxtop (rx_ring->rx_skb_top)
1599 if (!(staterr & E1000_RXD_STAT_EOP)) {
1600 /* this descriptor is only the beginning (or middle) */
1601 if (!rxtop) {
1602 /* this is the beginning of a chain */
1603 rxtop = skb;
1604 skb_fill_page_desc(rxtop, 0, buffer_info->page,
1605 0, length);
1606 } else {
1607 /* this is the middle of a chain */
1608 shinfo = skb_shinfo(rxtop);
1609 skb_fill_page_desc(rxtop, shinfo->nr_frags,
1610 buffer_info->page, 0,
1611 length);
1612 /* re-use the skb, only consumed the page */
1613 buffer_info->skb = skb;
1614 }
1615 e1000_consume_page(buffer_info, rxtop, length);
1616 goto next_desc;
1617 } else {
1618 if (rxtop) {
1619 /* end of the chain */
1620 shinfo = skb_shinfo(rxtop);
1621 skb_fill_page_desc(rxtop, shinfo->nr_frags,
1622 buffer_info->page, 0,
1623 length);
1624 /* re-use the current skb, we only consumed the
1625 * page
1626 */
1627 buffer_info->skb = skb;
1628 skb = rxtop;
1629 rxtop = NULL;
1630 e1000_consume_page(buffer_info, skb, length);
1631 } else {
1632 /* no chain, got EOP, this buf is the packet
1633 * copybreak to save the put_page/alloc_page
1634 */
1635 if (length <= copybreak &&
1636 skb_tailroom(skb) >= length) {
1637 u8 *vaddr;
1638 vaddr = kmap_atomic(buffer_info->page);
1639 memcpy(skb_tail_pointer(skb), vaddr,
1640 length);
1641 kunmap_atomic(vaddr);
1642 /* re-use the page, so don't erase
1643 * buffer_info->page
1644 */
1645 skb_put(skb, length);
1646 } else {
1647 skb_fill_page_desc(skb, 0,
1648 buffer_info->page, 0,
1649 length);
1650 e1000_consume_page(buffer_info, skb,
1651 length);
1652 }
1653 }
1654 }
1655
1656 /* Receive Checksum Offload */
1657 e1000_rx_checksum(adapter, staterr, skb);
1658
1659 e1000_rx_hash(netdev, rx_desc->wb.lower.hi_dword.rss, skb);
1660
1661 /* probably a little skewed due to removing CRC */
1662 total_rx_bytes += skb->len;
1663 total_rx_packets++;
1664
1665 /* eth type trans needs skb->data to point to something */
1666 if (!pskb_may_pull(skb, ETH_HLEN)) {
1667 e_err("pskb_may_pull failed.\n");
1668 dev_kfree_skb_irq(skb);
1669 goto next_desc;
1670 }
1671
1672 e1000_receive_skb(adapter, netdev, skb, staterr,
1673 rx_desc->wb.upper.vlan);
1674
1675next_desc:
1676 rx_desc->wb.upper.status_error &= cpu_to_le32(~0xFF);
1677
1678 /* return some buffers to hardware, one at a time is too slow */
1679 if (unlikely(cleaned_count >= E1000_RX_BUFFER_WRITE)) {
1680 adapter->alloc_rx_buf(rx_ring, cleaned_count,
1681 GFP_ATOMIC);
1682 cleaned_count = 0;
1683 }
1684
1685 /* use prefetched values */
1686 rx_desc = next_rxd;
1687 buffer_info = next_buffer;
1688
1689 staterr = le32_to_cpu(rx_desc->wb.upper.status_error);
1690 }
1691 rx_ring->next_to_clean = i;
1692
1693 cleaned_count = e1000_desc_unused(rx_ring);
1694 if (cleaned_count)
1695 adapter->alloc_rx_buf(rx_ring, cleaned_count, GFP_ATOMIC);
1696
1697 adapter->total_rx_bytes += total_rx_bytes;
1698 adapter->total_rx_packets += total_rx_packets;
1699 return cleaned;
1700}
1701
1702/**
1703 * e1000_clean_rx_ring - Free Rx Buffers per Queue
1704 * @rx_ring: Rx descriptor ring
1705 **/
1706static void e1000_clean_rx_ring(struct e1000_ring *rx_ring)
1707{
1708 struct e1000_adapter *adapter = rx_ring->adapter;
1709 struct e1000_buffer *buffer_info;
1710 struct e1000_ps_page *ps_page;
1711 struct pci_dev *pdev = adapter->pdev;
1712 unsigned int i, j;
1713
1714 /* Free all the Rx ring sk_buffs */
1715 for (i = 0; i < rx_ring->count; i++) {
1716 buffer_info = &rx_ring->buffer_info[i];
1717 if (buffer_info->dma) {
1718 if (adapter->clean_rx == e1000_clean_rx_irq)
1719 dma_unmap_single(&pdev->dev, buffer_info->dma,
1720 adapter->rx_buffer_len,
1721 DMA_FROM_DEVICE);
1722 else if (adapter->clean_rx == e1000_clean_jumbo_rx_irq)
1723 dma_unmap_page(&pdev->dev, buffer_info->dma,
1724 PAGE_SIZE, DMA_FROM_DEVICE);
1725 else if (adapter->clean_rx == e1000_clean_rx_irq_ps)
1726 dma_unmap_single(&pdev->dev, buffer_info->dma,
1727 adapter->rx_ps_bsize0,
1728 DMA_FROM_DEVICE);
1729 buffer_info->dma = 0;
1730 }
1731
1732 if (buffer_info->page) {
1733 put_page(buffer_info->page);
1734 buffer_info->page = NULL;
1735 }
1736
1737 if (buffer_info->skb) {
1738 dev_kfree_skb(buffer_info->skb);
1739 buffer_info->skb = NULL;
1740 }
1741
1742 for (j = 0; j < PS_PAGE_BUFFERS; j++) {
1743 ps_page = &buffer_info->ps_pages[j];
1744 if (!ps_page->page)
1745 break;
1746 dma_unmap_page(&pdev->dev, ps_page->dma, PAGE_SIZE,
1747 DMA_FROM_DEVICE);
1748 ps_page->dma = 0;
1749 put_page(ps_page->page);
1750 ps_page->page = NULL;
1751 }
1752 }
1753
1754 /* there also may be some cached data from a chained receive */
1755 if (rx_ring->rx_skb_top) {
1756 dev_kfree_skb(rx_ring->rx_skb_top);
1757 rx_ring->rx_skb_top = NULL;
1758 }
1759
1760 /* Zero out the descriptor ring */
1761 memset(rx_ring->desc, 0, rx_ring->size);
1762
1763 rx_ring->next_to_clean = 0;
1764 rx_ring->next_to_use = 0;
1765 adapter->flags2 &= ~FLAG2_IS_DISCARDING;
1766}
1767
1768static void e1000e_downshift_workaround(struct work_struct *work)
1769{
1770 struct e1000_adapter *adapter = container_of(work,
1771 struct e1000_adapter,
1772 downshift_task);
1773
1774 if (test_bit(__E1000_DOWN, &adapter->state))
1775 return;
1776
1777 e1000e_gig_downshift_workaround_ich8lan(&adapter->hw);
1778}
1779
1780/**
1781 * e1000_intr_msi - Interrupt Handler
1782 * @irq: interrupt number
1783 * @data: pointer to a network interface device structure
1784 **/
1785static irqreturn_t e1000_intr_msi(int __always_unused irq, void *data)
1786{
1787 struct net_device *netdev = data;
1788 struct e1000_adapter *adapter = netdev_priv(netdev);
1789 struct e1000_hw *hw = &adapter->hw;
1790 u32 icr = er32(ICR);
1791
1792 /* read ICR disables interrupts using IAM */
1793 if (icr & E1000_ICR_LSC) {
1794 hw->mac.get_link_status = true;
1795 /* ICH8 workaround-- Call gig speed drop workaround on cable
1796 * disconnect (LSC) before accessing any PHY registers
1797 */
1798 if ((adapter->flags & FLAG_LSC_GIG_SPEED_DROP) &&
1799 (!(er32(STATUS) & E1000_STATUS_LU)))
1800 schedule_work(&adapter->downshift_task);
1801
1802 /* 80003ES2LAN workaround-- For packet buffer work-around on
1803 * link down event; disable receives here in the ISR and reset
1804 * adapter in watchdog
1805 */
1806 if (netif_carrier_ok(netdev) &&
1807 adapter->flags & FLAG_RX_NEEDS_RESTART) {
1808 /* disable receives */
1809 u32 rctl = er32(RCTL);
1810
1811 ew32(RCTL, rctl & ~E1000_RCTL_EN);
1812 adapter->flags |= FLAG_RESTART_NOW;
1813 }
1814 /* guard against interrupt when we're going down */
1815 if (!test_bit(__E1000_DOWN, &adapter->state))
1816 mod_timer(&adapter->watchdog_timer, jiffies + 1);
1817 }
1818
1819 /* Reset on uncorrectable ECC error */
1820 if ((icr & E1000_ICR_ECCER) && (hw->mac.type >= e1000_pch_lpt)) {
1821 u32 pbeccsts = er32(PBECCSTS);
1822
1823 adapter->corr_errors +=
1824 pbeccsts & E1000_PBECCSTS_CORR_ERR_CNT_MASK;
1825 adapter->uncorr_errors +=
1826 (pbeccsts & E1000_PBECCSTS_UNCORR_ERR_CNT_MASK) >>
1827 E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT;
1828
1829 /* Do the reset outside of interrupt context */
1830 schedule_work(&adapter->reset_task);
1831
1832 /* return immediately since reset is imminent */
1833 return IRQ_HANDLED;
1834 }
1835
1836 if (napi_schedule_prep(&adapter->napi)) {
1837 adapter->total_tx_bytes = 0;
1838 adapter->total_tx_packets = 0;
1839 adapter->total_rx_bytes = 0;
1840 adapter->total_rx_packets = 0;
1841 __napi_schedule(&adapter->napi);
1842 }
1843
1844 return IRQ_HANDLED;
1845}
1846
1847/**
1848 * e1000_intr - Interrupt Handler
1849 * @irq: interrupt number
1850 * @data: pointer to a network interface device structure
1851 **/
1852static irqreturn_t e1000_intr(int __always_unused irq, void *data)
1853{
1854 struct net_device *netdev = data;
1855 struct e1000_adapter *adapter = netdev_priv(netdev);
1856 struct e1000_hw *hw = &adapter->hw;
1857 u32 rctl, icr = er32(ICR);
1858
1859 if (!icr || test_bit(__E1000_DOWN, &adapter->state))
1860 return IRQ_NONE; /* Not our interrupt */
1861
1862 /* IMS will not auto-mask if INT_ASSERTED is not set, and if it is
1863 * not set, then the adapter didn't send an interrupt
1864 */
1865 if (!(icr & E1000_ICR_INT_ASSERTED))
1866 return IRQ_NONE;
1867
1868 /* Interrupt Auto-Mask...upon reading ICR,
1869 * interrupts are masked. No need for the
1870 * IMC write
1871 */
1872
1873 if (icr & E1000_ICR_LSC) {
1874 hw->mac.get_link_status = true;
1875 /* ICH8 workaround-- Call gig speed drop workaround on cable
1876 * disconnect (LSC) before accessing any PHY registers
1877 */
1878 if ((adapter->flags & FLAG_LSC_GIG_SPEED_DROP) &&
1879 (!(er32(STATUS) & E1000_STATUS_LU)))
1880 schedule_work(&adapter->downshift_task);
1881
1882 /* 80003ES2LAN workaround--
1883 * For packet buffer work-around on link down event;
1884 * disable receives here in the ISR and
1885 * reset adapter in watchdog
1886 */
1887 if (netif_carrier_ok(netdev) &&
1888 (adapter->flags & FLAG_RX_NEEDS_RESTART)) {
1889 /* disable receives */
1890 rctl = er32(RCTL);
1891 ew32(RCTL, rctl & ~E1000_RCTL_EN);
1892 adapter->flags |= FLAG_RESTART_NOW;
1893 }
1894 /* guard against interrupt when we're going down */
1895 if (!test_bit(__E1000_DOWN, &adapter->state))
1896 mod_timer(&adapter->watchdog_timer, jiffies + 1);
1897 }
1898
1899 /* Reset on uncorrectable ECC error */
1900 if ((icr & E1000_ICR_ECCER) && (hw->mac.type >= e1000_pch_lpt)) {
1901 u32 pbeccsts = er32(PBECCSTS);
1902
1903 adapter->corr_errors +=
1904 pbeccsts & E1000_PBECCSTS_CORR_ERR_CNT_MASK;
1905 adapter->uncorr_errors +=
1906 (pbeccsts & E1000_PBECCSTS_UNCORR_ERR_CNT_MASK) >>
1907 E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT;
1908
1909 /* Do the reset outside of interrupt context */
1910 schedule_work(&adapter->reset_task);
1911
1912 /* return immediately since reset is imminent */
1913 return IRQ_HANDLED;
1914 }
1915
1916 if (napi_schedule_prep(&adapter->napi)) {
1917 adapter->total_tx_bytes = 0;
1918 adapter->total_tx_packets = 0;
1919 adapter->total_rx_bytes = 0;
1920 adapter->total_rx_packets = 0;
1921 __napi_schedule(&adapter->napi);
1922 }
1923
1924 return IRQ_HANDLED;
1925}
1926
1927static irqreturn_t e1000_msix_other(int __always_unused irq, void *data)
1928{
1929 struct net_device *netdev = data;
1930 struct e1000_adapter *adapter = netdev_priv(netdev);
1931 struct e1000_hw *hw = &adapter->hw;
1932 u32 icr = er32(ICR);
1933
1934 if (icr & adapter->eiac_mask)
1935 ew32(ICS, (icr & adapter->eiac_mask));
1936
1937 if (icr & E1000_ICR_LSC) {
1938 hw->mac.get_link_status = true;
1939 /* guard against interrupt when we're going down */
1940 if (!test_bit(__E1000_DOWN, &adapter->state))
1941 mod_timer(&adapter->watchdog_timer, jiffies + 1);
1942 }
1943
1944 if (!test_bit(__E1000_DOWN, &adapter->state))
1945 ew32(IMS, E1000_IMS_OTHER | IMS_OTHER_MASK);
1946
1947 return IRQ_HANDLED;
1948}
1949
1950static irqreturn_t e1000_intr_msix_tx(int __always_unused irq, void *data)
1951{
1952 struct net_device *netdev = data;
1953 struct e1000_adapter *adapter = netdev_priv(netdev);
1954 struct e1000_hw *hw = &adapter->hw;
1955 struct e1000_ring *tx_ring = adapter->tx_ring;
1956
1957 adapter->total_tx_bytes = 0;
1958 adapter->total_tx_packets = 0;
1959
1960 if (!e1000_clean_tx_irq(tx_ring))
1961 /* Ring was not completely cleaned, so fire another interrupt */
1962 ew32(ICS, tx_ring->ims_val);
1963
1964 if (!test_bit(__E1000_DOWN, &adapter->state))
1965 ew32(IMS, adapter->tx_ring->ims_val);
1966
1967 return IRQ_HANDLED;
1968}
1969
1970static irqreturn_t e1000_intr_msix_rx(int __always_unused irq, void *data)
1971{
1972 struct net_device *netdev = data;
1973 struct e1000_adapter *adapter = netdev_priv(netdev);
1974 struct e1000_ring *rx_ring = adapter->rx_ring;
1975
1976 /* Write the ITR value calculated at the end of the
1977 * previous interrupt.
1978 */
1979 if (rx_ring->set_itr) {
1980 u32 itr = rx_ring->itr_val ?
1981 1000000000 / (rx_ring->itr_val * 256) : 0;
1982
1983 writel(itr, rx_ring->itr_register);
1984 rx_ring->set_itr = 0;
1985 }
1986
1987 if (napi_schedule_prep(&adapter->napi)) {
1988 adapter->total_rx_bytes = 0;
1989 adapter->total_rx_packets = 0;
1990 __napi_schedule(&adapter->napi);
1991 }
1992 return IRQ_HANDLED;
1993}
1994
1995/**
1996 * e1000_configure_msix - Configure MSI-X hardware
1997 *
1998 * e1000_configure_msix sets up the hardware to properly
1999 * generate MSI-X interrupts.
2000 **/
2001static void e1000_configure_msix(struct e1000_adapter *adapter)
2002{
2003 struct e1000_hw *hw = &adapter->hw;
2004 struct e1000_ring *rx_ring = adapter->rx_ring;
2005 struct e1000_ring *tx_ring = adapter->tx_ring;
2006 int vector = 0;
2007 u32 ctrl_ext, ivar = 0;
2008
2009 adapter->eiac_mask = 0;
2010
2011 /* Workaround issue with spurious interrupts on 82574 in MSI-X mode */
2012 if (hw->mac.type == e1000_82574) {
2013 u32 rfctl = er32(RFCTL);
2014
2015 rfctl |= E1000_RFCTL_ACK_DIS;
2016 ew32(RFCTL, rfctl);
2017 }
2018
2019 /* Configure Rx vector */
2020 rx_ring->ims_val = E1000_IMS_RXQ0;
2021 adapter->eiac_mask |= rx_ring->ims_val;
2022 if (rx_ring->itr_val)
2023 writel(1000000000 / (rx_ring->itr_val * 256),
2024 rx_ring->itr_register);
2025 else
2026 writel(1, rx_ring->itr_register);
2027 ivar = E1000_IVAR_INT_ALLOC_VALID | vector;
2028
2029 /* Configure Tx vector */
2030 tx_ring->ims_val = E1000_IMS_TXQ0;
2031 vector++;
2032 if (tx_ring->itr_val)
2033 writel(1000000000 / (tx_ring->itr_val * 256),
2034 tx_ring->itr_register);
2035 else
2036 writel(1, tx_ring->itr_register);
2037 adapter->eiac_mask |= tx_ring->ims_val;
2038 ivar |= ((E1000_IVAR_INT_ALLOC_VALID | vector) << 8);
2039
2040 /* set vector for Other Causes, e.g. link changes */
2041 vector++;
2042 ivar |= ((E1000_IVAR_INT_ALLOC_VALID | vector) << 16);
2043 if (rx_ring->itr_val)
2044 writel(1000000000 / (rx_ring->itr_val * 256),
2045 hw->hw_addr + E1000_EITR_82574(vector));
2046 else
2047 writel(1, hw->hw_addr + E1000_EITR_82574(vector));
2048
2049 /* Cause Tx interrupts on every write back */
2050 ivar |= BIT(31);
2051
2052 ew32(IVAR, ivar);
2053
2054 /* enable MSI-X PBA support */
2055 ctrl_ext = er32(CTRL_EXT) & ~E1000_CTRL_EXT_IAME;
2056 ctrl_ext |= E1000_CTRL_EXT_PBA_CLR | E1000_CTRL_EXT_EIAME;
2057 ew32(CTRL_EXT, ctrl_ext);
2058 e1e_flush();
2059}
2060
2061void e1000e_reset_interrupt_capability(struct e1000_adapter *adapter)
2062{
2063 if (adapter->msix_entries) {
2064 pci_disable_msix(adapter->pdev);
2065 kfree(adapter->msix_entries);
2066 adapter->msix_entries = NULL;
2067 } else if (adapter->flags & FLAG_MSI_ENABLED) {
2068 pci_disable_msi(adapter->pdev);
2069 adapter->flags &= ~FLAG_MSI_ENABLED;
2070 }
2071}
2072
2073/**
2074 * e1000e_set_interrupt_capability - set MSI or MSI-X if supported
2075 *
2076 * Attempt to configure interrupts using the best available
2077 * capabilities of the hardware and kernel.
2078 **/
2079void e1000e_set_interrupt_capability(struct e1000_adapter *adapter)
2080{
2081 int err;
2082 int i;
2083
2084 switch (adapter->int_mode) {
2085 case E1000E_INT_MODE_MSIX:
2086 if (adapter->flags & FLAG_HAS_MSIX) {
2087 adapter->num_vectors = 3; /* RxQ0, TxQ0 and other */
2088 adapter->msix_entries = kcalloc(adapter->num_vectors,
2089 sizeof(struct
2090 msix_entry),
2091 GFP_KERNEL);
2092 if (adapter->msix_entries) {
2093 struct e1000_adapter *a = adapter;
2094
2095 for (i = 0; i < adapter->num_vectors; i++)
2096 adapter->msix_entries[i].entry = i;
2097
2098 err = pci_enable_msix_range(a->pdev,
2099 a->msix_entries,
2100 a->num_vectors,
2101 a->num_vectors);
2102 if (err > 0)
2103 return;
2104 }
2105 /* MSI-X failed, so fall through and try MSI */
2106 e_err("Failed to initialize MSI-X interrupts. Falling back to MSI interrupts.\n");
2107 e1000e_reset_interrupt_capability(adapter);
2108 }
2109 adapter->int_mode = E1000E_INT_MODE_MSI;
2110 fallthrough;
2111 case E1000E_INT_MODE_MSI:
2112 if (!pci_enable_msi(adapter->pdev)) {
2113 adapter->flags |= FLAG_MSI_ENABLED;
2114 } else {
2115 adapter->int_mode = E1000E_INT_MODE_LEGACY;
2116 e_err("Failed to initialize MSI interrupts. Falling back to legacy interrupts.\n");
2117 }
2118 fallthrough;
2119 case E1000E_INT_MODE_LEGACY:
2120 /* Don't do anything; this is the system default */
2121 break;
2122 }
2123
2124 /* store the number of vectors being used */
2125 adapter->num_vectors = 1;
2126}
2127
2128/**
2129 * e1000_request_msix - Initialize MSI-X interrupts
2130 *
2131 * e1000_request_msix allocates MSI-X vectors and requests interrupts from the
2132 * kernel.
2133 **/
2134static int e1000_request_msix(struct e1000_adapter *adapter)
2135{
2136 struct net_device *netdev = adapter->netdev;
2137 int err = 0, vector = 0;
2138
2139 if (strlen(netdev->name) < (IFNAMSIZ - 5))
2140 snprintf(adapter->rx_ring->name,
2141 sizeof(adapter->rx_ring->name) - 1,
2142 "%.14s-rx-0", netdev->name);
2143 else
2144 memcpy(adapter->rx_ring->name, netdev->name, IFNAMSIZ);
2145 err = request_irq(adapter->msix_entries[vector].vector,
2146 e1000_intr_msix_rx, 0, adapter->rx_ring->name,
2147 netdev);
2148 if (err)
2149 return err;
2150 adapter->rx_ring->itr_register = adapter->hw.hw_addr +
2151 E1000_EITR_82574(vector);
2152 adapter->rx_ring->itr_val = adapter->itr;
2153 vector++;
2154
2155 if (strlen(netdev->name) < (IFNAMSIZ - 5))
2156 snprintf(adapter->tx_ring->name,
2157 sizeof(adapter->tx_ring->name) - 1,
2158 "%.14s-tx-0", netdev->name);
2159 else
2160 memcpy(adapter->tx_ring->name, netdev->name, IFNAMSIZ);
2161 err = request_irq(adapter->msix_entries[vector].vector,
2162 e1000_intr_msix_tx, 0, adapter->tx_ring->name,
2163 netdev);
2164 if (err)
2165 return err;
2166 adapter->tx_ring->itr_register = adapter->hw.hw_addr +
2167 E1000_EITR_82574(vector);
2168 adapter->tx_ring->itr_val = adapter->itr;
2169 vector++;
2170
2171 err = request_irq(adapter->msix_entries[vector].vector,
2172 e1000_msix_other, 0, netdev->name, netdev);
2173 if (err)
2174 return err;
2175
2176 e1000_configure_msix(adapter);
2177
2178 return 0;
2179}
2180
2181/**
2182 * e1000_request_irq - initialize interrupts
2183 *
2184 * Attempts to configure interrupts using the best available
2185 * capabilities of the hardware and kernel.
2186 **/
2187static int e1000_request_irq(struct e1000_adapter *adapter)
2188{
2189 struct net_device *netdev = adapter->netdev;
2190 int err;
2191
2192 if (adapter->msix_entries) {
2193 err = e1000_request_msix(adapter);
2194 if (!err)
2195 return err;
2196 /* fall back to MSI */
2197 e1000e_reset_interrupt_capability(adapter);
2198 adapter->int_mode = E1000E_INT_MODE_MSI;
2199 e1000e_set_interrupt_capability(adapter);
2200 }
2201 if (adapter->flags & FLAG_MSI_ENABLED) {
2202 err = request_irq(adapter->pdev->irq, e1000_intr_msi, 0,
2203 netdev->name, netdev);
2204 if (!err)
2205 return err;
2206
2207 /* fall back to legacy interrupt */
2208 e1000e_reset_interrupt_capability(adapter);
2209 adapter->int_mode = E1000E_INT_MODE_LEGACY;
2210 }
2211
2212 err = request_irq(adapter->pdev->irq, e1000_intr, IRQF_SHARED,
2213 netdev->name, netdev);
2214 if (err)
2215 e_err("Unable to allocate interrupt, Error: %d\n", err);
2216
2217 return err;
2218}
2219
2220static void e1000_free_irq(struct e1000_adapter *adapter)
2221{
2222 struct net_device *netdev = adapter->netdev;
2223
2224 if (adapter->msix_entries) {
2225 int vector = 0;
2226
2227 free_irq(adapter->msix_entries[vector].vector, netdev);
2228 vector++;
2229
2230 free_irq(adapter->msix_entries[vector].vector, netdev);
2231 vector++;
2232
2233 /* Other Causes interrupt vector */
2234 free_irq(adapter->msix_entries[vector].vector, netdev);
2235 return;
2236 }
2237
2238 free_irq(adapter->pdev->irq, netdev);
2239}
2240
2241/**
2242 * e1000_irq_disable - Mask off interrupt generation on the NIC
2243 **/
2244static void e1000_irq_disable(struct e1000_adapter *adapter)
2245{
2246 struct e1000_hw *hw = &adapter->hw;
2247
2248 ew32(IMC, ~0);
2249 if (adapter->msix_entries)
2250 ew32(EIAC_82574, 0);
2251 e1e_flush();
2252
2253 if (adapter->msix_entries) {
2254 int i;
2255
2256 for (i = 0; i < adapter->num_vectors; i++)
2257 synchronize_irq(adapter->msix_entries[i].vector);
2258 } else {
2259 synchronize_irq(adapter->pdev->irq);
2260 }
2261}
2262
2263/**
2264 * e1000_irq_enable - Enable default interrupt generation settings
2265 **/
2266static void e1000_irq_enable(struct e1000_adapter *adapter)
2267{
2268 struct e1000_hw *hw = &adapter->hw;
2269
2270 if (adapter->msix_entries) {
2271 ew32(EIAC_82574, adapter->eiac_mask & E1000_EIAC_MASK_82574);
2272 ew32(IMS, adapter->eiac_mask | E1000_IMS_OTHER |
2273 IMS_OTHER_MASK);
2274 } else if (hw->mac.type >= e1000_pch_lpt) {
2275 ew32(IMS, IMS_ENABLE_MASK | E1000_IMS_ECCER);
2276 } else {
2277 ew32(IMS, IMS_ENABLE_MASK);
2278 }
2279 e1e_flush();
2280}
2281
2282/**
2283 * e1000e_get_hw_control - get control of the h/w from f/w
2284 * @adapter: address of board private structure
2285 *
2286 * e1000e_get_hw_control sets {CTRL_EXT|SWSM}:DRV_LOAD bit.
2287 * For ASF and Pass Through versions of f/w this means that
2288 * the driver is loaded. For AMT version (only with 82573)
2289 * of the f/w this means that the network i/f is open.
2290 **/
2291void e1000e_get_hw_control(struct e1000_adapter *adapter)
2292{
2293 struct e1000_hw *hw = &adapter->hw;
2294 u32 ctrl_ext;
2295 u32 swsm;
2296
2297 /* Let firmware know the driver has taken over */
2298 if (adapter->flags & FLAG_HAS_SWSM_ON_LOAD) {
2299 swsm = er32(SWSM);
2300 ew32(SWSM, swsm | E1000_SWSM_DRV_LOAD);
2301 } else if (adapter->flags & FLAG_HAS_CTRLEXT_ON_LOAD) {
2302 ctrl_ext = er32(CTRL_EXT);
2303 ew32(CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_DRV_LOAD);
2304 }
2305}
2306
2307/**
2308 * e1000e_release_hw_control - release control of the h/w to f/w
2309 * @adapter: address of board private structure
2310 *
2311 * e1000e_release_hw_control resets {CTRL_EXT|SWSM}:DRV_LOAD bit.
2312 * For ASF and Pass Through versions of f/w this means that the
2313 * driver is no longer loaded. For AMT version (only with 82573) i
2314 * of the f/w this means that the network i/f is closed.
2315 *
2316 **/
2317void e1000e_release_hw_control(struct e1000_adapter *adapter)
2318{
2319 struct e1000_hw *hw = &adapter->hw;
2320 u32 ctrl_ext;
2321 u32 swsm;
2322
2323 /* Let firmware taken over control of h/w */
2324 if (adapter->flags & FLAG_HAS_SWSM_ON_LOAD) {
2325 swsm = er32(SWSM);
2326 ew32(SWSM, swsm & ~E1000_SWSM_DRV_LOAD);
2327 } else if (adapter->flags & FLAG_HAS_CTRLEXT_ON_LOAD) {
2328 ctrl_ext = er32(CTRL_EXT);
2329 ew32(CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_DRV_LOAD);
2330 }
2331}
2332
2333/**
2334 * e1000_alloc_ring_dma - allocate memory for a ring structure
2335 **/
2336static int e1000_alloc_ring_dma(struct e1000_adapter *adapter,
2337 struct e1000_ring *ring)
2338{
2339 struct pci_dev *pdev = adapter->pdev;
2340
2341 ring->desc = dma_alloc_coherent(&pdev->dev, ring->size, &ring->dma,
2342 GFP_KERNEL);
2343 if (!ring->desc)
2344 return -ENOMEM;
2345
2346 return 0;
2347}
2348
2349/**
2350 * e1000e_setup_tx_resources - allocate Tx resources (Descriptors)
2351 * @tx_ring: Tx descriptor ring
2352 *
2353 * Return 0 on success, negative on failure
2354 **/
2355int e1000e_setup_tx_resources(struct e1000_ring *tx_ring)
2356{
2357 struct e1000_adapter *adapter = tx_ring->adapter;
2358 int err = -ENOMEM, size;
2359
2360 size = sizeof(struct e1000_buffer) * tx_ring->count;
2361 tx_ring->buffer_info = vzalloc(size);
2362 if (!tx_ring->buffer_info)
2363 goto err;
2364
2365 /* round up to nearest 4K */
2366 tx_ring->size = tx_ring->count * sizeof(struct e1000_tx_desc);
2367 tx_ring->size = ALIGN(tx_ring->size, 4096);
2368
2369 err = e1000_alloc_ring_dma(adapter, tx_ring);
2370 if (err)
2371 goto err;
2372
2373 tx_ring->next_to_use = 0;
2374 tx_ring->next_to_clean = 0;
2375
2376 return 0;
2377err:
2378 vfree(tx_ring->buffer_info);
2379 e_err("Unable to allocate memory for the transmit descriptor ring\n");
2380 return err;
2381}
2382
2383/**
2384 * e1000e_setup_rx_resources - allocate Rx resources (Descriptors)
2385 * @rx_ring: Rx descriptor ring
2386 *
2387 * Returns 0 on success, negative on failure
2388 **/
2389int e1000e_setup_rx_resources(struct e1000_ring *rx_ring)
2390{
2391 struct e1000_adapter *adapter = rx_ring->adapter;
2392 struct e1000_buffer *buffer_info;
2393 int i, size, desc_len, err = -ENOMEM;
2394
2395 size = sizeof(struct e1000_buffer) * rx_ring->count;
2396 rx_ring->buffer_info = vzalloc(size);
2397 if (!rx_ring->buffer_info)
2398 goto err;
2399
2400 for (i = 0; i < rx_ring->count; i++) {
2401 buffer_info = &rx_ring->buffer_info[i];
2402 buffer_info->ps_pages = kcalloc(PS_PAGE_BUFFERS,
2403 sizeof(struct e1000_ps_page),
2404 GFP_KERNEL);
2405 if (!buffer_info->ps_pages)
2406 goto err_pages;
2407 }
2408
2409 desc_len = sizeof(union e1000_rx_desc_packet_split);
2410
2411 /* Round up to nearest 4K */
2412 rx_ring->size = rx_ring->count * desc_len;
2413 rx_ring->size = ALIGN(rx_ring->size, 4096);
2414
2415 err = e1000_alloc_ring_dma(adapter, rx_ring);
2416 if (err)
2417 goto err_pages;
2418
2419 rx_ring->next_to_clean = 0;
2420 rx_ring->next_to_use = 0;
2421 rx_ring->rx_skb_top = NULL;
2422
2423 return 0;
2424
2425err_pages:
2426 for (i = 0; i < rx_ring->count; i++) {
2427 buffer_info = &rx_ring->buffer_info[i];
2428 kfree(buffer_info->ps_pages);
2429 }
2430err:
2431 vfree(rx_ring->buffer_info);
2432 e_err("Unable to allocate memory for the receive descriptor ring\n");
2433 return err;
2434}
2435
2436/**
2437 * e1000_clean_tx_ring - Free Tx Buffers
2438 * @tx_ring: Tx descriptor ring
2439 **/
2440static void e1000_clean_tx_ring(struct e1000_ring *tx_ring)
2441{
2442 struct e1000_adapter *adapter = tx_ring->adapter;
2443 struct e1000_buffer *buffer_info;
2444 unsigned long size;
2445 unsigned int i;
2446
2447 for (i = 0; i < tx_ring->count; i++) {
2448 buffer_info = &tx_ring->buffer_info[i];
2449 e1000_put_txbuf(tx_ring, buffer_info, false);
2450 }
2451
2452 netdev_reset_queue(adapter->netdev);
2453 size = sizeof(struct e1000_buffer) * tx_ring->count;
2454 memset(tx_ring->buffer_info, 0, size);
2455
2456 memset(tx_ring->desc, 0, tx_ring->size);
2457
2458 tx_ring->next_to_use = 0;
2459 tx_ring->next_to_clean = 0;
2460}
2461
2462/**
2463 * e1000e_free_tx_resources - Free Tx Resources per Queue
2464 * @tx_ring: Tx descriptor ring
2465 *
2466 * Free all transmit software resources
2467 **/
2468void e1000e_free_tx_resources(struct e1000_ring *tx_ring)
2469{
2470 struct e1000_adapter *adapter = tx_ring->adapter;
2471 struct pci_dev *pdev = adapter->pdev;
2472
2473 e1000_clean_tx_ring(tx_ring);
2474
2475 vfree(tx_ring->buffer_info);
2476 tx_ring->buffer_info = NULL;
2477
2478 dma_free_coherent(&pdev->dev, tx_ring->size, tx_ring->desc,
2479 tx_ring->dma);
2480 tx_ring->desc = NULL;
2481}
2482
2483/**
2484 * e1000e_free_rx_resources - Free Rx Resources
2485 * @rx_ring: Rx descriptor ring
2486 *
2487 * Free all receive software resources
2488 **/
2489void e1000e_free_rx_resources(struct e1000_ring *rx_ring)
2490{
2491 struct e1000_adapter *adapter = rx_ring->adapter;
2492 struct pci_dev *pdev = adapter->pdev;
2493 int i;
2494
2495 e1000_clean_rx_ring(rx_ring);
2496
2497 for (i = 0; i < rx_ring->count; i++)
2498 kfree(rx_ring->buffer_info[i].ps_pages);
2499
2500 vfree(rx_ring->buffer_info);
2501 rx_ring->buffer_info = NULL;
2502
2503 dma_free_coherent(&pdev->dev, rx_ring->size, rx_ring->desc,
2504 rx_ring->dma);
2505 rx_ring->desc = NULL;
2506}
2507
2508/**
2509 * e1000_update_itr - update the dynamic ITR value based on statistics
2510 * @adapter: pointer to adapter
2511 * @itr_setting: current adapter->itr
2512 * @packets: the number of packets during this measurement interval
2513 * @bytes: the number of bytes during this measurement interval
2514 *
2515 * Stores a new ITR value based on packets and byte
2516 * counts during the last interrupt. The advantage of per interrupt
2517 * computation is faster updates and more accurate ITR for the current
2518 * traffic pattern. Constants in this function were computed
2519 * based on theoretical maximum wire speed and thresholds were set based
2520 * on testing data as well as attempting to minimize response time
2521 * while increasing bulk throughput. This functionality is controlled
2522 * by the InterruptThrottleRate module parameter.
2523 **/
2524static unsigned int e1000_update_itr(u16 itr_setting, int packets, int bytes)
2525{
2526 unsigned int retval = itr_setting;
2527
2528 if (packets == 0)
2529 return itr_setting;
2530
2531 switch (itr_setting) {
2532 case lowest_latency:
2533 /* handle TSO and jumbo frames */
2534 if (bytes / packets > 8000)
2535 retval = bulk_latency;
2536 else if ((packets < 5) && (bytes > 512))
2537 retval = low_latency;
2538 break;
2539 case low_latency: /* 50 usec aka 20000 ints/s */
2540 if (bytes > 10000) {
2541 /* this if handles the TSO accounting */
2542 if (bytes / packets > 8000)
2543 retval = bulk_latency;
2544 else if ((packets < 10) || ((bytes / packets) > 1200))
2545 retval = bulk_latency;
2546 else if ((packets > 35))
2547 retval = lowest_latency;
2548 } else if (bytes / packets > 2000) {
2549 retval = bulk_latency;
2550 } else if (packets <= 2 && bytes < 512) {
2551 retval = lowest_latency;
2552 }
2553 break;
2554 case bulk_latency: /* 250 usec aka 4000 ints/s */
2555 if (bytes > 25000) {
2556 if (packets > 35)
2557 retval = low_latency;
2558 } else if (bytes < 6000) {
2559 retval = low_latency;
2560 }
2561 break;
2562 }
2563
2564 return retval;
2565}
2566
2567static void e1000_set_itr(struct e1000_adapter *adapter)
2568{
2569 u16 current_itr;
2570 u32 new_itr = adapter->itr;
2571
2572 /* for non-gigabit speeds, just fix the interrupt rate at 4000 */
2573 if (adapter->link_speed != SPEED_1000) {
2574 current_itr = 0;
2575 new_itr = 4000;
2576 goto set_itr_now;
2577 }
2578
2579 if (adapter->flags2 & FLAG2_DISABLE_AIM) {
2580 new_itr = 0;
2581 goto set_itr_now;
2582 }
2583
2584 adapter->tx_itr = e1000_update_itr(adapter->tx_itr,
2585 adapter->total_tx_packets,
2586 adapter->total_tx_bytes);
2587 /* conservative mode (itr 3) eliminates the lowest_latency setting */
2588 if (adapter->itr_setting == 3 && adapter->tx_itr == lowest_latency)
2589 adapter->tx_itr = low_latency;
2590
2591 adapter->rx_itr = e1000_update_itr(adapter->rx_itr,
2592 adapter->total_rx_packets,
2593 adapter->total_rx_bytes);
2594 /* conservative mode (itr 3) eliminates the lowest_latency setting */
2595 if (adapter->itr_setting == 3 && adapter->rx_itr == lowest_latency)
2596 adapter->rx_itr = low_latency;
2597
2598 current_itr = max(adapter->rx_itr, adapter->tx_itr);
2599
2600 /* counts and packets in update_itr are dependent on these numbers */
2601 switch (current_itr) {
2602 case lowest_latency:
2603 new_itr = 70000;
2604 break;
2605 case low_latency:
2606 new_itr = 20000; /* aka hwitr = ~200 */
2607 break;
2608 case bulk_latency:
2609 new_itr = 4000;
2610 break;
2611 default:
2612 break;
2613 }
2614
2615set_itr_now:
2616 if (new_itr != adapter->itr) {
2617 /* this attempts to bias the interrupt rate towards Bulk
2618 * by adding intermediate steps when interrupt rate is
2619 * increasing
2620 */
2621 new_itr = new_itr > adapter->itr ?
2622 min(adapter->itr + (new_itr >> 2), new_itr) : new_itr;
2623 adapter->itr = new_itr;
2624 adapter->rx_ring->itr_val = new_itr;
2625 if (adapter->msix_entries)
2626 adapter->rx_ring->set_itr = 1;
2627 else
2628 e1000e_write_itr(adapter, new_itr);
2629 }
2630}
2631
2632/**
2633 * e1000e_write_itr - write the ITR value to the appropriate registers
2634 * @adapter: address of board private structure
2635 * @itr: new ITR value to program
2636 *
2637 * e1000e_write_itr determines if the adapter is in MSI-X mode
2638 * and, if so, writes the EITR registers with the ITR value.
2639 * Otherwise, it writes the ITR value into the ITR register.
2640 **/
2641void e1000e_write_itr(struct e1000_adapter *adapter, u32 itr)
2642{
2643 struct e1000_hw *hw = &adapter->hw;
2644 u32 new_itr = itr ? 1000000000 / (itr * 256) : 0;
2645
2646 if (adapter->msix_entries) {
2647 int vector;
2648
2649 for (vector = 0; vector < adapter->num_vectors; vector++)
2650 writel(new_itr, hw->hw_addr + E1000_EITR_82574(vector));
2651 } else {
2652 ew32(ITR, new_itr);
2653 }
2654}
2655
2656/**
2657 * e1000_alloc_queues - Allocate memory for all rings
2658 * @adapter: board private structure to initialize
2659 **/
2660static int e1000_alloc_queues(struct e1000_adapter *adapter)
2661{
2662 int size = sizeof(struct e1000_ring);
2663
2664 adapter->tx_ring = kzalloc(size, GFP_KERNEL);
2665 if (!adapter->tx_ring)
2666 goto err;
2667 adapter->tx_ring->count = adapter->tx_ring_count;
2668 adapter->tx_ring->adapter = adapter;
2669
2670 adapter->rx_ring = kzalloc(size, GFP_KERNEL);
2671 if (!adapter->rx_ring)
2672 goto err;
2673 adapter->rx_ring->count = adapter->rx_ring_count;
2674 adapter->rx_ring->adapter = adapter;
2675
2676 return 0;
2677err:
2678 e_err("Unable to allocate memory for queues\n");
2679 kfree(adapter->rx_ring);
2680 kfree(adapter->tx_ring);
2681 return -ENOMEM;
2682}
2683
2684/**
2685 * e1000e_poll - NAPI Rx polling callback
2686 * @napi: struct associated with this polling callback
2687 * @budget: number of packets driver is allowed to process this poll
2688 **/
2689static int e1000e_poll(struct napi_struct *napi, int budget)
2690{
2691 struct e1000_adapter *adapter = container_of(napi, struct e1000_adapter,
2692 napi);
2693 struct e1000_hw *hw = &adapter->hw;
2694 struct net_device *poll_dev = adapter->netdev;
2695 int tx_cleaned = 1, work_done = 0;
2696
2697 adapter = netdev_priv(poll_dev);
2698
2699 if (!adapter->msix_entries ||
2700 (adapter->rx_ring->ims_val & adapter->tx_ring->ims_val))
2701 tx_cleaned = e1000_clean_tx_irq(adapter->tx_ring);
2702
2703 adapter->clean_rx(adapter->rx_ring, &work_done, budget);
2704
2705 if (!tx_cleaned || work_done == budget)
2706 return budget;
2707
2708 /* Exit the polling mode, but don't re-enable interrupts if stack might
2709 * poll us due to busy-polling
2710 */
2711 if (likely(napi_complete_done(napi, work_done))) {
2712 if (adapter->itr_setting & 3)
2713 e1000_set_itr(adapter);
2714 if (!test_bit(__E1000_DOWN, &adapter->state)) {
2715 if (adapter->msix_entries)
2716 ew32(IMS, adapter->rx_ring->ims_val);
2717 else
2718 e1000_irq_enable(adapter);
2719 }
2720 }
2721
2722 return work_done;
2723}
2724
2725static int e1000_vlan_rx_add_vid(struct net_device *netdev,
2726 __always_unused __be16 proto, u16 vid)
2727{
2728 struct e1000_adapter *adapter = netdev_priv(netdev);
2729 struct e1000_hw *hw = &adapter->hw;
2730 u32 vfta, index;
2731
2732 /* don't update vlan cookie if already programmed */
2733 if ((adapter->hw.mng_cookie.status &
2734 E1000_MNG_DHCP_COOKIE_STATUS_VLAN) &&
2735 (vid == adapter->mng_vlan_id))
2736 return 0;
2737
2738 /* add VID to filter table */
2739 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) {
2740 index = (vid >> 5) & 0x7F;
2741 vfta = E1000_READ_REG_ARRAY(hw, E1000_VFTA, index);
2742 vfta |= BIT((vid & 0x1F));
2743 hw->mac.ops.write_vfta(hw, index, vfta);
2744 }
2745
2746 set_bit(vid, adapter->active_vlans);
2747
2748 return 0;
2749}
2750
2751static int e1000_vlan_rx_kill_vid(struct net_device *netdev,
2752 __always_unused __be16 proto, u16 vid)
2753{
2754 struct e1000_adapter *adapter = netdev_priv(netdev);
2755 struct e1000_hw *hw = &adapter->hw;
2756 u32 vfta, index;
2757
2758 if ((adapter->hw.mng_cookie.status &
2759 E1000_MNG_DHCP_COOKIE_STATUS_VLAN) &&
2760 (vid == adapter->mng_vlan_id)) {
2761 /* release control to f/w */
2762 e1000e_release_hw_control(adapter);
2763 return 0;
2764 }
2765
2766 /* remove VID from filter table */
2767 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) {
2768 index = (vid >> 5) & 0x7F;
2769 vfta = E1000_READ_REG_ARRAY(hw, E1000_VFTA, index);
2770 vfta &= ~BIT((vid & 0x1F));
2771 hw->mac.ops.write_vfta(hw, index, vfta);
2772 }
2773
2774 clear_bit(vid, adapter->active_vlans);
2775
2776 return 0;
2777}
2778
2779/**
2780 * e1000e_vlan_filter_disable - helper to disable hw VLAN filtering
2781 * @adapter: board private structure to initialize
2782 **/
2783static void e1000e_vlan_filter_disable(struct e1000_adapter *adapter)
2784{
2785 struct net_device *netdev = adapter->netdev;
2786 struct e1000_hw *hw = &adapter->hw;
2787 u32 rctl;
2788
2789 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) {
2790 /* disable VLAN receive filtering */
2791 rctl = er32(RCTL);
2792 rctl &= ~(E1000_RCTL_VFE | E1000_RCTL_CFIEN);
2793 ew32(RCTL, rctl);
2794
2795 if (adapter->mng_vlan_id != (u16)E1000_MNG_VLAN_NONE) {
2796 e1000_vlan_rx_kill_vid(netdev, htons(ETH_P_8021Q),
2797 adapter->mng_vlan_id);
2798 adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
2799 }
2800 }
2801}
2802
2803/**
2804 * e1000e_vlan_filter_enable - helper to enable HW VLAN filtering
2805 * @adapter: board private structure to initialize
2806 **/
2807static void e1000e_vlan_filter_enable(struct e1000_adapter *adapter)
2808{
2809 struct e1000_hw *hw = &adapter->hw;
2810 u32 rctl;
2811
2812 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) {
2813 /* enable VLAN receive filtering */
2814 rctl = er32(RCTL);
2815 rctl |= E1000_RCTL_VFE;
2816 rctl &= ~E1000_RCTL_CFIEN;
2817 ew32(RCTL, rctl);
2818 }
2819}
2820
2821/**
2822 * e1000e_vlan_strip_disable - helper to disable HW VLAN stripping
2823 * @adapter: board private structure to initialize
2824 **/
2825static void e1000e_vlan_strip_disable(struct e1000_adapter *adapter)
2826{
2827 struct e1000_hw *hw = &adapter->hw;
2828 u32 ctrl;
2829
2830 /* disable VLAN tag insert/strip */
2831 ctrl = er32(CTRL);
2832 ctrl &= ~E1000_CTRL_VME;
2833 ew32(CTRL, ctrl);
2834}
2835
2836/**
2837 * e1000e_vlan_strip_enable - helper to enable HW VLAN stripping
2838 * @adapter: board private structure to initialize
2839 **/
2840static void e1000e_vlan_strip_enable(struct e1000_adapter *adapter)
2841{
2842 struct e1000_hw *hw = &adapter->hw;
2843 u32 ctrl;
2844
2845 /* enable VLAN tag insert/strip */
2846 ctrl = er32(CTRL);
2847 ctrl |= E1000_CTRL_VME;
2848 ew32(CTRL, ctrl);
2849}
2850
2851static void e1000_update_mng_vlan(struct e1000_adapter *adapter)
2852{
2853 struct net_device *netdev = adapter->netdev;
2854 u16 vid = adapter->hw.mng_cookie.vlan_id;
2855 u16 old_vid = adapter->mng_vlan_id;
2856
2857 if (adapter->hw.mng_cookie.status & E1000_MNG_DHCP_COOKIE_STATUS_VLAN) {
2858 e1000_vlan_rx_add_vid(netdev, htons(ETH_P_8021Q), vid);
2859 adapter->mng_vlan_id = vid;
2860 }
2861
2862 if ((old_vid != (u16)E1000_MNG_VLAN_NONE) && (vid != old_vid))
2863 e1000_vlan_rx_kill_vid(netdev, htons(ETH_P_8021Q), old_vid);
2864}
2865
2866static void e1000_restore_vlan(struct e1000_adapter *adapter)
2867{
2868 u16 vid;
2869
2870 e1000_vlan_rx_add_vid(adapter->netdev, htons(ETH_P_8021Q), 0);
2871
2872 for_each_set_bit(vid, adapter->active_vlans, VLAN_N_VID)
2873 e1000_vlan_rx_add_vid(adapter->netdev, htons(ETH_P_8021Q), vid);
2874}
2875
2876static void e1000_init_manageability_pt(struct e1000_adapter *adapter)
2877{
2878 struct e1000_hw *hw = &adapter->hw;
2879 u32 manc, manc2h, mdef, i, j;
2880
2881 if (!(adapter->flags & FLAG_MNG_PT_ENABLED))
2882 return;
2883
2884 manc = er32(MANC);
2885
2886 /* enable receiving management packets to the host. this will probably
2887 * generate destination unreachable messages from the host OS, but
2888 * the packets will be handled on SMBUS
2889 */
2890 manc |= E1000_MANC_EN_MNG2HOST;
2891 manc2h = er32(MANC2H);
2892
2893 switch (hw->mac.type) {
2894 default:
2895 manc2h |= (E1000_MANC2H_PORT_623 | E1000_MANC2H_PORT_664);
2896 break;
2897 case e1000_82574:
2898 case e1000_82583:
2899 /* Check if IPMI pass-through decision filter already exists;
2900 * if so, enable it.
2901 */
2902 for (i = 0, j = 0; i < 8; i++) {
2903 mdef = er32(MDEF(i));
2904
2905 /* Ignore filters with anything other than IPMI ports */
2906 if (mdef & ~(E1000_MDEF_PORT_623 | E1000_MDEF_PORT_664))
2907 continue;
2908
2909 /* Enable this decision filter in MANC2H */
2910 if (mdef)
2911 manc2h |= BIT(i);
2912
2913 j |= mdef;
2914 }
2915
2916 if (j == (E1000_MDEF_PORT_623 | E1000_MDEF_PORT_664))
2917 break;
2918
2919 /* Create new decision filter in an empty filter */
2920 for (i = 0, j = 0; i < 8; i++)
2921 if (er32(MDEF(i)) == 0) {
2922 ew32(MDEF(i), (E1000_MDEF_PORT_623 |
2923 E1000_MDEF_PORT_664));
2924 manc2h |= BIT(1);
2925 j++;
2926 break;
2927 }
2928
2929 if (!j)
2930 e_warn("Unable to create IPMI pass-through filter\n");
2931 break;
2932 }
2933
2934 ew32(MANC2H, manc2h);
2935 ew32(MANC, manc);
2936}
2937
2938/**
2939 * e1000_configure_tx - Configure Transmit Unit after Reset
2940 * @adapter: board private structure
2941 *
2942 * Configure the Tx unit of the MAC after a reset.
2943 **/
2944static void e1000_configure_tx(struct e1000_adapter *adapter)
2945{
2946 struct e1000_hw *hw = &adapter->hw;
2947 struct e1000_ring *tx_ring = adapter->tx_ring;
2948 u64 tdba;
2949 u32 tdlen, tctl, tarc;
2950
2951 /* Setup the HW Tx Head and Tail descriptor pointers */
2952 tdba = tx_ring->dma;
2953 tdlen = tx_ring->count * sizeof(struct e1000_tx_desc);
2954 ew32(TDBAL(0), (tdba & DMA_BIT_MASK(32)));
2955 ew32(TDBAH(0), (tdba >> 32));
2956 ew32(TDLEN(0), tdlen);
2957 ew32(TDH(0), 0);
2958 ew32(TDT(0), 0);
2959 tx_ring->head = adapter->hw.hw_addr + E1000_TDH(0);
2960 tx_ring->tail = adapter->hw.hw_addr + E1000_TDT(0);
2961
2962 writel(0, tx_ring->head);
2963 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA)
2964 e1000e_update_tdt_wa(tx_ring, 0);
2965 else
2966 writel(0, tx_ring->tail);
2967
2968 /* Set the Tx Interrupt Delay register */
2969 ew32(TIDV, adapter->tx_int_delay);
2970 /* Tx irq moderation */
2971 ew32(TADV, adapter->tx_abs_int_delay);
2972
2973 if (adapter->flags2 & FLAG2_DMA_BURST) {
2974 u32 txdctl = er32(TXDCTL(0));
2975
2976 txdctl &= ~(E1000_TXDCTL_PTHRESH | E1000_TXDCTL_HTHRESH |
2977 E1000_TXDCTL_WTHRESH);
2978 /* set up some performance related parameters to encourage the
2979 * hardware to use the bus more efficiently in bursts, depends
2980 * on the tx_int_delay to be enabled,
2981 * wthresh = 1 ==> burst write is disabled to avoid Tx stalls
2982 * hthresh = 1 ==> prefetch when one or more available
2983 * pthresh = 0x1f ==> prefetch if internal cache 31 or less
2984 * BEWARE: this seems to work but should be considered first if
2985 * there are Tx hangs or other Tx related bugs
2986 */
2987 txdctl |= E1000_TXDCTL_DMA_BURST_ENABLE;
2988 ew32(TXDCTL(0), txdctl);
2989 }
2990 /* erratum work around: set txdctl the same for both queues */
2991 ew32(TXDCTL(1), er32(TXDCTL(0)));
2992
2993 /* Program the Transmit Control Register */
2994 tctl = er32(TCTL);
2995 tctl &= ~E1000_TCTL_CT;
2996 tctl |= E1000_TCTL_PSP | E1000_TCTL_RTLC |
2997 (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT);
2998
2999 if (adapter->flags & FLAG_TARC_SPEED_MODE_BIT) {
3000 tarc = er32(TARC(0));
3001 /* set the speed mode bit, we'll clear it if we're not at
3002 * gigabit link later
3003 */
3004#define SPEED_MODE_BIT BIT(21)
3005 tarc |= SPEED_MODE_BIT;
3006 ew32(TARC(0), tarc);
3007 }
3008
3009 /* errata: program both queues to unweighted RR */
3010 if (adapter->flags & FLAG_TARC_SET_BIT_ZERO) {
3011 tarc = er32(TARC(0));
3012 tarc |= 1;
3013 ew32(TARC(0), tarc);
3014 tarc = er32(TARC(1));
3015 tarc |= 1;
3016 ew32(TARC(1), tarc);
3017 }
3018
3019 /* Setup Transmit Descriptor Settings for eop descriptor */
3020 adapter->txd_cmd = E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS;
3021
3022 /* only set IDE if we are delaying interrupts using the timers */
3023 if (adapter->tx_int_delay)
3024 adapter->txd_cmd |= E1000_TXD_CMD_IDE;
3025
3026 /* enable Report Status bit */
3027 adapter->txd_cmd |= E1000_TXD_CMD_RS;
3028
3029 ew32(TCTL, tctl);
3030
3031 hw->mac.ops.config_collision_dist(hw);
3032
3033 /* SPT and KBL Si errata workaround to avoid data corruption */
3034 if (hw->mac.type == e1000_pch_spt) {
3035 u32 reg_val;
3036
3037 reg_val = er32(IOSFPC);
3038 reg_val |= E1000_RCTL_RDMTS_HEX;
3039 ew32(IOSFPC, reg_val);
3040
3041 reg_val = er32(TARC(0));
3042 /* SPT and KBL Si errata workaround to avoid Tx hang.
3043 * Dropping the number of outstanding requests from
3044 * 3 to 2 in order to avoid a buffer overrun.
3045 */
3046 reg_val &= ~E1000_TARC0_CB_MULTIQ_3_REQ;
3047 reg_val |= E1000_TARC0_CB_MULTIQ_2_REQ;
3048 ew32(TARC(0), reg_val);
3049 }
3050}
3051
3052/**
3053 * e1000_setup_rctl - configure the receive control registers
3054 * @adapter: Board private structure
3055 **/
3056#define PAGE_USE_COUNT(S) (((S) >> PAGE_SHIFT) + \
3057 (((S) & (PAGE_SIZE - 1)) ? 1 : 0))
3058static void e1000_setup_rctl(struct e1000_adapter *adapter)
3059{
3060 struct e1000_hw *hw = &adapter->hw;
3061 u32 rctl, rfctl;
3062 u32 pages = 0;
3063
3064 /* Workaround Si errata on PCHx - configure jumbo frame flow.
3065 * If jumbo frames not set, program related MAC/PHY registers
3066 * to h/w defaults
3067 */
3068 if (hw->mac.type >= e1000_pch2lan) {
3069 s32 ret_val;
3070
3071 if (adapter->netdev->mtu > ETH_DATA_LEN)
3072 ret_val = e1000_lv_jumbo_workaround_ich8lan(hw, true);
3073 else
3074 ret_val = e1000_lv_jumbo_workaround_ich8lan(hw, false);
3075
3076 if (ret_val)
3077 e_dbg("failed to enable|disable jumbo frame workaround mode\n");
3078 }
3079
3080 /* Program MC offset vector base */
3081 rctl = er32(RCTL);
3082 rctl &= ~(3 << E1000_RCTL_MO_SHIFT);
3083 rctl |= E1000_RCTL_EN | E1000_RCTL_BAM |
3084 E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF |
3085 (adapter->hw.mac.mc_filter_type << E1000_RCTL_MO_SHIFT);
3086
3087 /* Do not Store bad packets */
3088 rctl &= ~E1000_RCTL_SBP;
3089
3090 /* Enable Long Packet receive */
3091 if (adapter->netdev->mtu <= ETH_DATA_LEN)
3092 rctl &= ~E1000_RCTL_LPE;
3093 else
3094 rctl |= E1000_RCTL_LPE;
3095
3096 /* Some systems expect that the CRC is included in SMBUS traffic. The
3097 * hardware strips the CRC before sending to both SMBUS (BMC) and to
3098 * host memory when this is enabled
3099 */
3100 if (adapter->flags2 & FLAG2_CRC_STRIPPING)
3101 rctl |= E1000_RCTL_SECRC;
3102
3103 /* Workaround Si errata on 82577 PHY - configure IPG for jumbos */
3104 if ((hw->phy.type == e1000_phy_82577) && (rctl & E1000_RCTL_LPE)) {
3105 u16 phy_data;
3106
3107 e1e_rphy(hw, PHY_REG(770, 26), &phy_data);
3108 phy_data &= 0xfff8;
3109 phy_data |= BIT(2);
3110 e1e_wphy(hw, PHY_REG(770, 26), phy_data);
3111
3112 e1e_rphy(hw, 22, &phy_data);
3113 phy_data &= 0x0fff;
3114 phy_data |= BIT(14);
3115 e1e_wphy(hw, 0x10, 0x2823);
3116 e1e_wphy(hw, 0x11, 0x0003);
3117 e1e_wphy(hw, 22, phy_data);
3118 }
3119
3120 /* Setup buffer sizes */
3121 rctl &= ~E1000_RCTL_SZ_4096;
3122 rctl |= E1000_RCTL_BSEX;
3123 switch (adapter->rx_buffer_len) {
3124 case 2048:
3125 default:
3126 rctl |= E1000_RCTL_SZ_2048;
3127 rctl &= ~E1000_RCTL_BSEX;
3128 break;
3129 case 4096:
3130 rctl |= E1000_RCTL_SZ_4096;
3131 break;
3132 case 8192:
3133 rctl |= E1000_RCTL_SZ_8192;
3134 break;
3135 case 16384:
3136 rctl |= E1000_RCTL_SZ_16384;
3137 break;
3138 }
3139
3140 /* Enable Extended Status in all Receive Descriptors */
3141 rfctl = er32(RFCTL);
3142 rfctl |= E1000_RFCTL_EXTEN;
3143 ew32(RFCTL, rfctl);
3144
3145 /* 82571 and greater support packet-split where the protocol
3146 * header is placed in skb->data and the packet data is
3147 * placed in pages hanging off of skb_shinfo(skb)->nr_frags.
3148 * In the case of a non-split, skb->data is linearly filled,
3149 * followed by the page buffers. Therefore, skb->data is
3150 * sized to hold the largest protocol header.
3151 *
3152 * allocations using alloc_page take too long for regular MTU
3153 * so only enable packet split for jumbo frames
3154 *
3155 * Using pages when the page size is greater than 16k wastes
3156 * a lot of memory, since we allocate 3 pages at all times
3157 * per packet.
3158 */
3159 pages = PAGE_USE_COUNT(adapter->netdev->mtu);
3160 if ((pages <= 3) && (PAGE_SIZE <= 16384) && (rctl & E1000_RCTL_LPE))
3161 adapter->rx_ps_pages = pages;
3162 else
3163 adapter->rx_ps_pages = 0;
3164
3165 if (adapter->rx_ps_pages) {
3166 u32 psrctl = 0;
3167
3168 /* Enable Packet split descriptors */
3169 rctl |= E1000_RCTL_DTYP_PS;
3170
3171 psrctl |= adapter->rx_ps_bsize0 >> E1000_PSRCTL_BSIZE0_SHIFT;
3172
3173 switch (adapter->rx_ps_pages) {
3174 case 3:
3175 psrctl |= PAGE_SIZE << E1000_PSRCTL_BSIZE3_SHIFT;
3176 fallthrough;
3177 case 2:
3178 psrctl |= PAGE_SIZE << E1000_PSRCTL_BSIZE2_SHIFT;
3179 fallthrough;
3180 case 1:
3181 psrctl |= PAGE_SIZE >> E1000_PSRCTL_BSIZE1_SHIFT;
3182 break;
3183 }
3184
3185 ew32(PSRCTL, psrctl);
3186 }
3187
3188 /* This is useful for sniffing bad packets. */
3189 if (adapter->netdev->features & NETIF_F_RXALL) {
3190 /* UPE and MPE will be handled by normal PROMISC logic
3191 * in e1000e_set_rx_mode
3192 */
3193 rctl |= (E1000_RCTL_SBP | /* Receive bad packets */
3194 E1000_RCTL_BAM | /* RX All Bcast Pkts */
3195 E1000_RCTL_PMCF); /* RX All MAC Ctrl Pkts */
3196
3197 rctl &= ~(E1000_RCTL_VFE | /* Disable VLAN filter */
3198 E1000_RCTL_DPF | /* Allow filtered pause */
3199 E1000_RCTL_CFIEN); /* Dis VLAN CFIEN Filter */
3200 /* Do not mess with E1000_CTRL_VME, it affects transmit as well,
3201 * and that breaks VLANs.
3202 */
3203 }
3204
3205 ew32(RCTL, rctl);
3206 /* just started the receive unit, no need to restart */
3207 adapter->flags &= ~FLAG_RESTART_NOW;
3208}
3209
3210/**
3211 * e1000_configure_rx - Configure Receive Unit after Reset
3212 * @adapter: board private structure
3213 *
3214 * Configure the Rx unit of the MAC after a reset.
3215 **/
3216static void e1000_configure_rx(struct e1000_adapter *adapter)
3217{
3218 struct e1000_hw *hw = &adapter->hw;
3219 struct e1000_ring *rx_ring = adapter->rx_ring;
3220 u64 rdba;
3221 u32 rdlen, rctl, rxcsum, ctrl_ext;
3222
3223 if (adapter->rx_ps_pages) {
3224 /* this is a 32 byte descriptor */
3225 rdlen = rx_ring->count *
3226 sizeof(union e1000_rx_desc_packet_split);
3227 adapter->clean_rx = e1000_clean_rx_irq_ps;
3228 adapter->alloc_rx_buf = e1000_alloc_rx_buffers_ps;
3229 } else if (adapter->netdev->mtu > ETH_FRAME_LEN + ETH_FCS_LEN) {
3230 rdlen = rx_ring->count * sizeof(union e1000_rx_desc_extended);
3231 adapter->clean_rx = e1000_clean_jumbo_rx_irq;
3232 adapter->alloc_rx_buf = e1000_alloc_jumbo_rx_buffers;
3233 } else {
3234 rdlen = rx_ring->count * sizeof(union e1000_rx_desc_extended);
3235 adapter->clean_rx = e1000_clean_rx_irq;
3236 adapter->alloc_rx_buf = e1000_alloc_rx_buffers;
3237 }
3238
3239 /* disable receives while setting up the descriptors */
3240 rctl = er32(RCTL);
3241 if (!(adapter->flags2 & FLAG2_NO_DISABLE_RX))
3242 ew32(RCTL, rctl & ~E1000_RCTL_EN);
3243 e1e_flush();
3244 usleep_range(10000, 11000);
3245
3246 if (adapter->flags2 & FLAG2_DMA_BURST) {
3247 /* set the writeback threshold (only takes effect if the RDTR
3248 * is set). set GRAN=1 and write back up to 0x4 worth, and
3249 * enable prefetching of 0x20 Rx descriptors
3250 * granularity = 01
3251 * wthresh = 04,
3252 * hthresh = 04,
3253 * pthresh = 0x20
3254 */
3255 ew32(RXDCTL(0), E1000_RXDCTL_DMA_BURST_ENABLE);
3256 ew32(RXDCTL(1), E1000_RXDCTL_DMA_BURST_ENABLE);
3257 }
3258
3259 /* set the Receive Delay Timer Register */
3260 ew32(RDTR, adapter->rx_int_delay);
3261
3262 /* irq moderation */
3263 ew32(RADV, adapter->rx_abs_int_delay);
3264 if ((adapter->itr_setting != 0) && (adapter->itr != 0))
3265 e1000e_write_itr(adapter, adapter->itr);
3266
3267 ctrl_ext = er32(CTRL_EXT);
3268 /* Auto-Mask interrupts upon ICR access */
3269 ctrl_ext |= E1000_CTRL_EXT_IAME;
3270 ew32(IAM, 0xffffffff);
3271 ew32(CTRL_EXT, ctrl_ext);
3272 e1e_flush();
3273
3274 /* Setup the HW Rx Head and Tail Descriptor Pointers and
3275 * the Base and Length of the Rx Descriptor Ring
3276 */
3277 rdba = rx_ring->dma;
3278 ew32(RDBAL(0), (rdba & DMA_BIT_MASK(32)));
3279 ew32(RDBAH(0), (rdba >> 32));
3280 ew32(RDLEN(0), rdlen);
3281 ew32(RDH(0), 0);
3282 ew32(RDT(0), 0);
3283 rx_ring->head = adapter->hw.hw_addr + E1000_RDH(0);
3284 rx_ring->tail = adapter->hw.hw_addr + E1000_RDT(0);
3285
3286 writel(0, rx_ring->head);
3287 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA)
3288 e1000e_update_rdt_wa(rx_ring, 0);
3289 else
3290 writel(0, rx_ring->tail);
3291
3292 /* Enable Receive Checksum Offload for TCP and UDP */
3293 rxcsum = er32(RXCSUM);
3294 if (adapter->netdev->features & NETIF_F_RXCSUM)
3295 rxcsum |= E1000_RXCSUM_TUOFL;
3296 else
3297 rxcsum &= ~E1000_RXCSUM_TUOFL;
3298 ew32(RXCSUM, rxcsum);
3299
3300 /* With jumbo frames, excessive C-state transition latencies result
3301 * in dropped transactions.
3302 */
3303 if (adapter->netdev->mtu > ETH_DATA_LEN) {
3304 u32 lat =
3305 ((er32(PBA) & E1000_PBA_RXA_MASK) * 1024 -
3306 adapter->max_frame_size) * 8 / 1000;
3307
3308 if (adapter->flags & FLAG_IS_ICH) {
3309 u32 rxdctl = er32(RXDCTL(0));
3310
3311 ew32(RXDCTL(0), rxdctl | 0x3 | BIT(8));
3312 }
3313
3314 dev_info(&adapter->pdev->dev,
3315 "Some CPU C-states have been disabled in order to enable jumbo frames\n");
3316 cpu_latency_qos_update_request(&adapter->pm_qos_req, lat);
3317 } else {
3318 cpu_latency_qos_update_request(&adapter->pm_qos_req,
3319 PM_QOS_DEFAULT_VALUE);
3320 }
3321
3322 /* Enable Receives */
3323 ew32(RCTL, rctl);
3324}
3325
3326/**
3327 * e1000e_write_mc_addr_list - write multicast addresses to MTA
3328 * @netdev: network interface device structure
3329 *
3330 * Writes multicast address list to the MTA hash table.
3331 * Returns: -ENOMEM on failure
3332 * 0 on no addresses written
3333 * X on writing X addresses to MTA
3334 */
3335static int e1000e_write_mc_addr_list(struct net_device *netdev)
3336{
3337 struct e1000_adapter *adapter = netdev_priv(netdev);
3338 struct e1000_hw *hw = &adapter->hw;
3339 struct netdev_hw_addr *ha;
3340 u8 *mta_list;
3341 int i;
3342
3343 if (netdev_mc_empty(netdev)) {
3344 /* nothing to program, so clear mc list */
3345 hw->mac.ops.update_mc_addr_list(hw, NULL, 0);
3346 return 0;
3347 }
3348
3349 mta_list = kcalloc(netdev_mc_count(netdev), ETH_ALEN, GFP_ATOMIC);
3350 if (!mta_list)
3351 return -ENOMEM;
3352
3353 /* update_mc_addr_list expects a packed array of only addresses. */
3354 i = 0;
3355 netdev_for_each_mc_addr(ha, netdev)
3356 memcpy(mta_list + (i++ * ETH_ALEN), ha->addr, ETH_ALEN);
3357
3358 hw->mac.ops.update_mc_addr_list(hw, mta_list, i);
3359 kfree(mta_list);
3360
3361 return netdev_mc_count(netdev);
3362}
3363
3364/**
3365 * e1000e_write_uc_addr_list - write unicast addresses to RAR table
3366 * @netdev: network interface device structure
3367 *
3368 * Writes unicast address list to the RAR table.
3369 * Returns: -ENOMEM on failure/insufficient address space
3370 * 0 on no addresses written
3371 * X on writing X addresses to the RAR table
3372 **/
3373static int e1000e_write_uc_addr_list(struct net_device *netdev)
3374{
3375 struct e1000_adapter *adapter = netdev_priv(netdev);
3376 struct e1000_hw *hw = &adapter->hw;
3377 unsigned int rar_entries;
3378 int count = 0;
3379
3380 rar_entries = hw->mac.ops.rar_get_count(hw);
3381
3382 /* save a rar entry for our hardware address */
3383 rar_entries--;
3384
3385 /* save a rar entry for the LAA workaround */
3386 if (adapter->flags & FLAG_RESET_OVERWRITES_LAA)
3387 rar_entries--;
3388
3389 /* return ENOMEM indicating insufficient memory for addresses */
3390 if (netdev_uc_count(netdev) > rar_entries)
3391 return -ENOMEM;
3392
3393 if (!netdev_uc_empty(netdev) && rar_entries) {
3394 struct netdev_hw_addr *ha;
3395
3396 /* write the addresses in reverse order to avoid write
3397 * combining
3398 */
3399 netdev_for_each_uc_addr(ha, netdev) {
3400 int ret_val;
3401
3402 if (!rar_entries)
3403 break;
3404 ret_val = hw->mac.ops.rar_set(hw, ha->addr, rar_entries--);
3405 if (ret_val < 0)
3406 return -ENOMEM;
3407 count++;
3408 }
3409 }
3410
3411 /* zero out the remaining RAR entries not used above */
3412 for (; rar_entries > 0; rar_entries--) {
3413 ew32(RAH(rar_entries), 0);
3414 ew32(RAL(rar_entries), 0);
3415 }
3416 e1e_flush();
3417
3418 return count;
3419}
3420
3421/**
3422 * e1000e_set_rx_mode - secondary unicast, Multicast and Promiscuous mode set
3423 * @netdev: network interface device structure
3424 *
3425 * The ndo_set_rx_mode entry point is called whenever the unicast or multicast
3426 * address list or the network interface flags are updated. This routine is
3427 * responsible for configuring the hardware for proper unicast, multicast,
3428 * promiscuous mode, and all-multi behavior.
3429 **/
3430static void e1000e_set_rx_mode(struct net_device *netdev)
3431{
3432 struct e1000_adapter *adapter = netdev_priv(netdev);
3433 struct e1000_hw *hw = &adapter->hw;
3434 u32 rctl;
3435
3436 if (pm_runtime_suspended(netdev->dev.parent))
3437 return;
3438
3439 /* Check for Promiscuous and All Multicast modes */
3440 rctl = er32(RCTL);
3441
3442 /* clear the affected bits */
3443 rctl &= ~(E1000_RCTL_UPE | E1000_RCTL_MPE);
3444
3445 if (netdev->flags & IFF_PROMISC) {
3446 rctl |= (E1000_RCTL_UPE | E1000_RCTL_MPE);
3447 /* Do not hardware filter VLANs in promisc mode */
3448 e1000e_vlan_filter_disable(adapter);
3449 } else {
3450 int count;
3451
3452 if (netdev->flags & IFF_ALLMULTI) {
3453 rctl |= E1000_RCTL_MPE;
3454 } else {
3455 /* Write addresses to the MTA, if the attempt fails
3456 * then we should just turn on promiscuous mode so
3457 * that we can at least receive multicast traffic
3458 */
3459 count = e1000e_write_mc_addr_list(netdev);
3460 if (count < 0)
3461 rctl |= E1000_RCTL_MPE;
3462 }
3463 e1000e_vlan_filter_enable(adapter);
3464 /* Write addresses to available RAR registers, if there is not
3465 * sufficient space to store all the addresses then enable
3466 * unicast promiscuous mode
3467 */
3468 count = e1000e_write_uc_addr_list(netdev);
3469 if (count < 0)
3470 rctl |= E1000_RCTL_UPE;
3471 }
3472
3473 ew32(RCTL, rctl);
3474
3475 if (netdev->features & NETIF_F_HW_VLAN_CTAG_RX)
3476 e1000e_vlan_strip_enable(adapter);
3477 else
3478 e1000e_vlan_strip_disable(adapter);
3479}
3480
3481static void e1000e_setup_rss_hash(struct e1000_adapter *adapter)
3482{
3483 struct e1000_hw *hw = &adapter->hw;
3484 u32 mrqc, rxcsum;
3485 u32 rss_key[10];
3486 int i;
3487
3488 netdev_rss_key_fill(rss_key, sizeof(rss_key));
3489 for (i = 0; i < 10; i++)
3490 ew32(RSSRK(i), rss_key[i]);
3491
3492 /* Direct all traffic to queue 0 */
3493 for (i = 0; i < 32; i++)
3494 ew32(RETA(i), 0);
3495
3496 /* Disable raw packet checksumming so that RSS hash is placed in
3497 * descriptor on writeback.
3498 */
3499 rxcsum = er32(RXCSUM);
3500 rxcsum |= E1000_RXCSUM_PCSD;
3501
3502 ew32(RXCSUM, rxcsum);
3503
3504 mrqc = (E1000_MRQC_RSS_FIELD_IPV4 |
3505 E1000_MRQC_RSS_FIELD_IPV4_TCP |
3506 E1000_MRQC_RSS_FIELD_IPV6 |
3507 E1000_MRQC_RSS_FIELD_IPV6_TCP |
3508 E1000_MRQC_RSS_FIELD_IPV6_TCP_EX);
3509
3510 ew32(MRQC, mrqc);
3511}
3512
3513/**
3514 * e1000e_get_base_timinca - get default SYSTIM time increment attributes
3515 * @adapter: board private structure
3516 * @timinca: pointer to returned time increment attributes
3517 *
3518 * Get attributes for incrementing the System Time Register SYSTIML/H at
3519 * the default base frequency, and set the cyclecounter shift value.
3520 **/
3521s32 e1000e_get_base_timinca(struct e1000_adapter *adapter, u32 *timinca)
3522{
3523 struct e1000_hw *hw = &adapter->hw;
3524 u32 incvalue, incperiod, shift;
3525
3526 /* Make sure clock is enabled on I217/I218/I219 before checking
3527 * the frequency
3528 */
3529 if ((hw->mac.type >= e1000_pch_lpt) &&
3530 !(er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_ENABLED) &&
3531 !(er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_ENABLED)) {
3532 u32 fextnvm7 = er32(FEXTNVM7);
3533
3534 if (!(fextnvm7 & BIT(0))) {
3535 ew32(FEXTNVM7, fextnvm7 | BIT(0));
3536 e1e_flush();
3537 }
3538 }
3539
3540 switch (hw->mac.type) {
3541 case e1000_pch2lan:
3542 /* Stable 96MHz frequency */
3543 incperiod = INCPERIOD_96MHZ;
3544 incvalue = INCVALUE_96MHZ;
3545 shift = INCVALUE_SHIFT_96MHZ;
3546 adapter->cc.shift = shift + INCPERIOD_SHIFT_96MHZ;
3547 break;
3548 case e1000_pch_lpt:
3549 if (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_SYSCFI) {
3550 /* Stable 96MHz frequency */
3551 incperiod = INCPERIOD_96MHZ;
3552 incvalue = INCVALUE_96MHZ;
3553 shift = INCVALUE_SHIFT_96MHZ;
3554 adapter->cc.shift = shift + INCPERIOD_SHIFT_96MHZ;
3555 } else {
3556 /* Stable 25MHz frequency */
3557 incperiod = INCPERIOD_25MHZ;
3558 incvalue = INCVALUE_25MHZ;
3559 shift = INCVALUE_SHIFT_25MHZ;
3560 adapter->cc.shift = shift;
3561 }
3562 break;
3563 case e1000_pch_spt:
3564 /* Stable 24MHz frequency */
3565 incperiod = INCPERIOD_24MHZ;
3566 incvalue = INCVALUE_24MHZ;
3567 shift = INCVALUE_SHIFT_24MHZ;
3568 adapter->cc.shift = shift;
3569 break;
3570 case e1000_pch_cnp:
3571 case e1000_pch_tgp:
3572 case e1000_pch_adp:
3573 if (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_SYSCFI) {
3574 /* Stable 24MHz frequency */
3575 incperiod = INCPERIOD_24MHZ;
3576 incvalue = INCVALUE_24MHZ;
3577 shift = INCVALUE_SHIFT_24MHZ;
3578 adapter->cc.shift = shift;
3579 } else {
3580 /* Stable 38400KHz frequency */
3581 incperiod = INCPERIOD_38400KHZ;
3582 incvalue = INCVALUE_38400KHZ;
3583 shift = INCVALUE_SHIFT_38400KHZ;
3584 adapter->cc.shift = shift;
3585 }
3586 break;
3587 case e1000_82574:
3588 case e1000_82583:
3589 /* Stable 25MHz frequency */
3590 incperiod = INCPERIOD_25MHZ;
3591 incvalue = INCVALUE_25MHZ;
3592 shift = INCVALUE_SHIFT_25MHZ;
3593 adapter->cc.shift = shift;
3594 break;
3595 default:
3596 return -EINVAL;
3597 }
3598
3599 *timinca = ((incperiod << E1000_TIMINCA_INCPERIOD_SHIFT) |
3600 ((incvalue << shift) & E1000_TIMINCA_INCVALUE_MASK));
3601
3602 return 0;
3603}
3604
3605/**
3606 * e1000e_config_hwtstamp - configure the hwtstamp registers and enable/disable
3607 * @adapter: board private structure
3608 *
3609 * Outgoing time stamping can be enabled and disabled. Play nice and
3610 * disable it when requested, although it shouldn't cause any overhead
3611 * when no packet needs it. At most one packet in the queue may be
3612 * marked for time stamping, otherwise it would be impossible to tell
3613 * for sure to which packet the hardware time stamp belongs.
3614 *
3615 * Incoming time stamping has to be configured via the hardware filters.
3616 * Not all combinations are supported, in particular event type has to be
3617 * specified. Matching the kind of event packet is not supported, with the
3618 * exception of "all V2 events regardless of level 2 or 4".
3619 **/
3620static int e1000e_config_hwtstamp(struct e1000_adapter *adapter,
3621 struct hwtstamp_config *config)
3622{
3623 struct e1000_hw *hw = &adapter->hw;
3624 u32 tsync_tx_ctl = E1000_TSYNCTXCTL_ENABLED;
3625 u32 tsync_rx_ctl = E1000_TSYNCRXCTL_ENABLED;
3626 u32 rxmtrl = 0;
3627 u16 rxudp = 0;
3628 bool is_l4 = false;
3629 bool is_l2 = false;
3630 u32 regval;
3631
3632 if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP))
3633 return -EINVAL;
3634
3635 /* flags reserved for future extensions - must be zero */
3636 if (config->flags)
3637 return -EINVAL;
3638
3639 switch (config->tx_type) {
3640 case HWTSTAMP_TX_OFF:
3641 tsync_tx_ctl = 0;
3642 break;
3643 case HWTSTAMP_TX_ON:
3644 break;
3645 default:
3646 return -ERANGE;
3647 }
3648
3649 switch (config->rx_filter) {
3650 case HWTSTAMP_FILTER_NONE:
3651 tsync_rx_ctl = 0;
3652 break;
3653 case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
3654 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L4_V1;
3655 rxmtrl = E1000_RXMTRL_PTP_V1_SYNC_MESSAGE;
3656 is_l4 = true;
3657 break;
3658 case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
3659 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L4_V1;
3660 rxmtrl = E1000_RXMTRL_PTP_V1_DELAY_REQ_MESSAGE;
3661 is_l4 = true;
3662 break;
3663 case HWTSTAMP_FILTER_PTP_V2_L2_SYNC:
3664 /* Also time stamps V2 L2 Path Delay Request/Response */
3665 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_V2;
3666 rxmtrl = E1000_RXMTRL_PTP_V2_SYNC_MESSAGE;
3667 is_l2 = true;
3668 break;
3669 case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ:
3670 /* Also time stamps V2 L2 Path Delay Request/Response. */
3671 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_V2;
3672 rxmtrl = E1000_RXMTRL_PTP_V2_DELAY_REQ_MESSAGE;
3673 is_l2 = true;
3674 break;
3675 case HWTSTAMP_FILTER_PTP_V2_L4_SYNC:
3676 /* Hardware cannot filter just V2 L4 Sync messages */
3677 fallthrough;
3678 case HWTSTAMP_FILTER_PTP_V2_SYNC:
3679 /* Also time stamps V2 Path Delay Request/Response. */
3680 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_L4_V2;
3681 rxmtrl = E1000_RXMTRL_PTP_V2_SYNC_MESSAGE;
3682 is_l2 = true;
3683 is_l4 = true;
3684 break;
3685 case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ:
3686 /* Hardware cannot filter just V2 L4 Delay Request messages */
3687 fallthrough;
3688 case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ:
3689 /* Also time stamps V2 Path Delay Request/Response. */
3690 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_L4_V2;
3691 rxmtrl = E1000_RXMTRL_PTP_V2_DELAY_REQ_MESSAGE;
3692 is_l2 = true;
3693 is_l4 = true;
3694 break;
3695 case HWTSTAMP_FILTER_PTP_V2_L4_EVENT:
3696 case HWTSTAMP_FILTER_PTP_V2_L2_EVENT:
3697 /* Hardware cannot filter just V2 L4 or L2 Event messages */
3698 fallthrough;
3699 case HWTSTAMP_FILTER_PTP_V2_EVENT:
3700 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_EVENT_V2;
3701 config->rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT;
3702 is_l2 = true;
3703 is_l4 = true;
3704 break;
3705 case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
3706 /* For V1, the hardware can only filter Sync messages or
3707 * Delay Request messages but not both so fall-through to
3708 * time stamp all packets.
3709 */
3710 fallthrough;
3711 case HWTSTAMP_FILTER_NTP_ALL:
3712 case HWTSTAMP_FILTER_ALL:
3713 is_l2 = true;
3714 is_l4 = true;
3715 tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_ALL;
3716 config->rx_filter = HWTSTAMP_FILTER_ALL;
3717 break;
3718 default:
3719 return -ERANGE;
3720 }
3721
3722 adapter->hwtstamp_config = *config;
3723
3724 /* enable/disable Tx h/w time stamping */
3725 regval = er32(TSYNCTXCTL);
3726 regval &= ~E1000_TSYNCTXCTL_ENABLED;
3727 regval |= tsync_tx_ctl;
3728 ew32(TSYNCTXCTL, regval);
3729 if ((er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_ENABLED) !=
3730 (regval & E1000_TSYNCTXCTL_ENABLED)) {
3731 e_err("Timesync Tx Control register not set as expected\n");
3732 return -EAGAIN;
3733 }
3734
3735 /* enable/disable Rx h/w time stamping */
3736 regval = er32(TSYNCRXCTL);
3737 regval &= ~(E1000_TSYNCRXCTL_ENABLED | E1000_TSYNCRXCTL_TYPE_MASK);
3738 regval |= tsync_rx_ctl;
3739 ew32(TSYNCRXCTL, regval);
3740 if ((er32(TSYNCRXCTL) & (E1000_TSYNCRXCTL_ENABLED |
3741 E1000_TSYNCRXCTL_TYPE_MASK)) !=
3742 (regval & (E1000_TSYNCRXCTL_ENABLED |
3743 E1000_TSYNCRXCTL_TYPE_MASK))) {
3744 e_err("Timesync Rx Control register not set as expected\n");
3745 return -EAGAIN;
3746 }
3747
3748 /* L2: define ethertype filter for time stamped packets */
3749 if (is_l2)
3750 rxmtrl |= ETH_P_1588;
3751
3752 /* define which PTP packets get time stamped */
3753 ew32(RXMTRL, rxmtrl);
3754
3755 /* Filter by destination port */
3756 if (is_l4) {
3757 rxudp = PTP_EV_PORT;
3758 cpu_to_be16s(&rxudp);
3759 }
3760 ew32(RXUDP, rxudp);
3761
3762 e1e_flush();
3763
3764 /* Clear TSYNCRXCTL_VALID & TSYNCTXCTL_VALID bit */
3765 er32(RXSTMPH);
3766 er32(TXSTMPH);
3767
3768 return 0;
3769}
3770
3771/**
3772 * e1000_configure - configure the hardware for Rx and Tx
3773 * @adapter: private board structure
3774 **/
3775static void e1000_configure(struct e1000_adapter *adapter)
3776{
3777 struct e1000_ring *rx_ring = adapter->rx_ring;
3778
3779 e1000e_set_rx_mode(adapter->netdev);
3780
3781 e1000_restore_vlan(adapter);
3782 e1000_init_manageability_pt(adapter);
3783
3784 e1000_configure_tx(adapter);
3785
3786 if (adapter->netdev->features & NETIF_F_RXHASH)
3787 e1000e_setup_rss_hash(adapter);
3788 e1000_setup_rctl(adapter);
3789 e1000_configure_rx(adapter);
3790 adapter->alloc_rx_buf(rx_ring, e1000_desc_unused(rx_ring), GFP_KERNEL);
3791}
3792
3793/**
3794 * e1000e_power_up_phy - restore link in case the phy was powered down
3795 * @adapter: address of board private structure
3796 *
3797 * The phy may be powered down to save power and turn off link when the
3798 * driver is unloaded and wake on lan is not enabled (among others)
3799 * *** this routine MUST be followed by a call to e1000e_reset ***
3800 **/
3801void e1000e_power_up_phy(struct e1000_adapter *adapter)
3802{
3803 if (adapter->hw.phy.ops.power_up)
3804 adapter->hw.phy.ops.power_up(&adapter->hw);
3805
3806 adapter->hw.mac.ops.setup_link(&adapter->hw);
3807}
3808
3809/**
3810 * e1000_power_down_phy - Power down the PHY
3811 *
3812 * Power down the PHY so no link is implied when interface is down.
3813 * The PHY cannot be powered down if management or WoL is active.
3814 */
3815static void e1000_power_down_phy(struct e1000_adapter *adapter)
3816{
3817 if (adapter->hw.phy.ops.power_down)
3818 adapter->hw.phy.ops.power_down(&adapter->hw);
3819}
3820
3821/**
3822 * e1000_flush_tx_ring - remove all descriptors from the tx_ring
3823 *
3824 * We want to clear all pending descriptors from the TX ring.
3825 * zeroing happens when the HW reads the regs. We assign the ring itself as
3826 * the data of the next descriptor. We don't care about the data we are about
3827 * to reset the HW.
3828 */
3829static void e1000_flush_tx_ring(struct e1000_adapter *adapter)
3830{
3831 struct e1000_hw *hw = &adapter->hw;
3832 struct e1000_ring *tx_ring = adapter->tx_ring;
3833 struct e1000_tx_desc *tx_desc = NULL;
3834 u32 tdt, tctl, txd_lower = E1000_TXD_CMD_IFCS;
3835 u16 size = 512;
3836
3837 tctl = er32(TCTL);
3838 ew32(TCTL, tctl | E1000_TCTL_EN);
3839 tdt = er32(TDT(0));
3840 BUG_ON(tdt != tx_ring->next_to_use);
3841 tx_desc = E1000_TX_DESC(*tx_ring, tx_ring->next_to_use);
3842 tx_desc->buffer_addr = cpu_to_le64(tx_ring->dma);
3843
3844 tx_desc->lower.data = cpu_to_le32(txd_lower | size);
3845 tx_desc->upper.data = 0;
3846 /* flush descriptors to memory before notifying the HW */
3847 wmb();
3848 tx_ring->next_to_use++;
3849 if (tx_ring->next_to_use == tx_ring->count)
3850 tx_ring->next_to_use = 0;
3851 ew32(TDT(0), tx_ring->next_to_use);
3852 usleep_range(200, 250);
3853}
3854
3855/**
3856 * e1000_flush_rx_ring - remove all descriptors from the rx_ring
3857 *
3858 * Mark all descriptors in the RX ring as consumed and disable the rx ring
3859 */
3860static void e1000_flush_rx_ring(struct e1000_adapter *adapter)
3861{
3862 u32 rctl, rxdctl;
3863 struct e1000_hw *hw = &adapter->hw;
3864
3865 rctl = er32(RCTL);
3866 ew32(RCTL, rctl & ~E1000_RCTL_EN);
3867 e1e_flush();
3868 usleep_range(100, 150);
3869
3870 rxdctl = er32(RXDCTL(0));
3871 /* zero the lower 14 bits (prefetch and host thresholds) */
3872 rxdctl &= 0xffffc000;
3873
3874 /* update thresholds: prefetch threshold to 31, host threshold to 1
3875 * and make sure the granularity is "descriptors" and not "cache lines"
3876 */
3877 rxdctl |= (0x1F | BIT(8) | E1000_RXDCTL_THRESH_UNIT_DESC);
3878
3879 ew32(RXDCTL(0), rxdctl);
3880 /* momentarily enable the RX ring for the changes to take effect */
3881 ew32(RCTL, rctl | E1000_RCTL_EN);
3882 e1e_flush();
3883 usleep_range(100, 150);
3884 ew32(RCTL, rctl & ~E1000_RCTL_EN);
3885}
3886
3887/**
3888 * e1000_flush_desc_rings - remove all descriptors from the descriptor rings
3889 *
3890 * In i219, the descriptor rings must be emptied before resetting the HW
3891 * or before changing the device state to D3 during runtime (runtime PM).
3892 *
3893 * Failure to do this will cause the HW to enter a unit hang state which can
3894 * only be released by PCI reset on the device
3895 *
3896 */
3897
3898static void e1000_flush_desc_rings(struct e1000_adapter *adapter)
3899{
3900 u16 hang_state;
3901 u32 fext_nvm11, tdlen;
3902 struct e1000_hw *hw = &adapter->hw;
3903
3904 /* First, disable MULR fix in FEXTNVM11 */
3905 fext_nvm11 = er32(FEXTNVM11);
3906 fext_nvm11 |= E1000_FEXTNVM11_DISABLE_MULR_FIX;
3907 ew32(FEXTNVM11, fext_nvm11);
3908 /* do nothing if we're not in faulty state, or if the queue is empty */
3909 tdlen = er32(TDLEN(0));
3910 pci_read_config_word(adapter->pdev, PCICFG_DESC_RING_STATUS,
3911 &hang_state);
3912 if (!(hang_state & FLUSH_DESC_REQUIRED) || !tdlen)
3913 return;
3914 e1000_flush_tx_ring(adapter);
3915 /* recheck, maybe the fault is caused by the rx ring */
3916 pci_read_config_word(adapter->pdev, PCICFG_DESC_RING_STATUS,
3917 &hang_state);
3918 if (hang_state & FLUSH_DESC_REQUIRED)
3919 e1000_flush_rx_ring(adapter);
3920}
3921
3922/**
3923 * e1000e_systim_reset - reset the timesync registers after a hardware reset
3924 * @adapter: board private structure
3925 *
3926 * When the MAC is reset, all hardware bits for timesync will be reset to the
3927 * default values. This function will restore the settings last in place.
3928 * Since the clock SYSTIME registers are reset, we will simply restore the
3929 * cyclecounter to the kernel real clock time.
3930 **/
3931static void e1000e_systim_reset(struct e1000_adapter *adapter)
3932{
3933 struct ptp_clock_info *info = &adapter->ptp_clock_info;
3934 struct e1000_hw *hw = &adapter->hw;
3935 unsigned long flags;
3936 u32 timinca;
3937 s32 ret_val;
3938
3939 if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP))
3940 return;
3941
3942 if (info->adjfreq) {
3943 /* restore the previous ptp frequency delta */
3944 ret_val = info->adjfreq(info, adapter->ptp_delta);
3945 } else {
3946 /* set the default base frequency if no adjustment possible */
3947 ret_val = e1000e_get_base_timinca(adapter, &timinca);
3948 if (!ret_val)
3949 ew32(TIMINCA, timinca);
3950 }
3951
3952 if (ret_val) {
3953 dev_warn(&adapter->pdev->dev,
3954 "Failed to restore TIMINCA clock rate delta: %d\n",
3955 ret_val);
3956 return;
3957 }
3958
3959 /* reset the systim ns time counter */
3960 spin_lock_irqsave(&adapter->systim_lock, flags);
3961 timecounter_init(&adapter->tc, &adapter->cc,
3962 ktime_to_ns(ktime_get_real()));
3963 spin_unlock_irqrestore(&adapter->systim_lock, flags);
3964
3965 /* restore the previous hwtstamp configuration settings */
3966 e1000e_config_hwtstamp(adapter, &adapter->hwtstamp_config);
3967}
3968
3969/**
3970 * e1000e_reset - bring the hardware into a known good state
3971 *
3972 * This function boots the hardware and enables some settings that
3973 * require a configuration cycle of the hardware - those cannot be
3974 * set/changed during runtime. After reset the device needs to be
3975 * properly configured for Rx, Tx etc.
3976 */
3977void e1000e_reset(struct e1000_adapter *adapter)
3978{
3979 struct e1000_mac_info *mac = &adapter->hw.mac;
3980 struct e1000_fc_info *fc = &adapter->hw.fc;
3981 struct e1000_hw *hw = &adapter->hw;
3982 u32 tx_space, min_tx_space, min_rx_space;
3983 u32 pba = adapter->pba;
3984 u16 hwm;
3985
3986 /* reset Packet Buffer Allocation to default */
3987 ew32(PBA, pba);
3988
3989 if (adapter->max_frame_size > (VLAN_ETH_FRAME_LEN + ETH_FCS_LEN)) {
3990 /* To maintain wire speed transmits, the Tx FIFO should be
3991 * large enough to accommodate two full transmit packets,
3992 * rounded up to the next 1KB and expressed in KB. Likewise,
3993 * the Rx FIFO should be large enough to accommodate at least
3994 * one full receive packet and is similarly rounded up and
3995 * expressed in KB.
3996 */
3997 pba = er32(PBA);
3998 /* upper 16 bits has Tx packet buffer allocation size in KB */
3999 tx_space = pba >> 16;
4000 /* lower 16 bits has Rx packet buffer allocation size in KB */
4001 pba &= 0xffff;
4002 /* the Tx fifo also stores 16 bytes of information about the Tx
4003 * but don't include ethernet FCS because hardware appends it
4004 */
4005 min_tx_space = (adapter->max_frame_size +
4006 sizeof(struct e1000_tx_desc) - ETH_FCS_LEN) * 2;
4007 min_tx_space = ALIGN(min_tx_space, 1024);
4008 min_tx_space >>= 10;
4009 /* software strips receive CRC, so leave room for it */
4010 min_rx_space = adapter->max_frame_size;
4011 min_rx_space = ALIGN(min_rx_space, 1024);
4012 min_rx_space >>= 10;
4013
4014 /* If current Tx allocation is less than the min Tx FIFO size,
4015 * and the min Tx FIFO size is less than the current Rx FIFO
4016 * allocation, take space away from current Rx allocation
4017 */
4018 if ((tx_space < min_tx_space) &&
4019 ((min_tx_space - tx_space) < pba)) {
4020 pba -= min_tx_space - tx_space;
4021
4022 /* if short on Rx space, Rx wins and must trump Tx
4023 * adjustment
4024 */
4025 if (pba < min_rx_space)
4026 pba = min_rx_space;
4027 }
4028
4029 ew32(PBA, pba);
4030 }
4031
4032 /* flow control settings
4033 *
4034 * The high water mark must be low enough to fit one full frame
4035 * (or the size used for early receive) above it in the Rx FIFO.
4036 * Set it to the lower of:
4037 * - 90% of the Rx FIFO size, and
4038 * - the full Rx FIFO size minus one full frame
4039 */
4040 if (adapter->flags & FLAG_DISABLE_FC_PAUSE_TIME)
4041 fc->pause_time = 0xFFFF;
4042 else
4043 fc->pause_time = E1000_FC_PAUSE_TIME;
4044 fc->send_xon = true;
4045 fc->current_mode = fc->requested_mode;
4046
4047 switch (hw->mac.type) {
4048 case e1000_ich9lan:
4049 case e1000_ich10lan:
4050 if (adapter->netdev->mtu > ETH_DATA_LEN) {
4051 pba = 14;
4052 ew32(PBA, pba);
4053 fc->high_water = 0x2800;
4054 fc->low_water = fc->high_water - 8;
4055 break;
4056 }
4057 fallthrough;
4058 default:
4059 hwm = min(((pba << 10) * 9 / 10),
4060 ((pba << 10) - adapter->max_frame_size));
4061
4062 fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */
4063 fc->low_water = fc->high_water - 8;
4064 break;
4065 case e1000_pchlan:
4066 /* Workaround PCH LOM adapter hangs with certain network
4067 * loads. If hangs persist, try disabling Tx flow control.
4068 */
4069 if (adapter->netdev->mtu > ETH_DATA_LEN) {
4070 fc->high_water = 0x3500;
4071 fc->low_water = 0x1500;
4072 } else {
4073 fc->high_water = 0x5000;
4074 fc->low_water = 0x3000;
4075 }
4076 fc->refresh_time = 0x1000;
4077 break;
4078 case e1000_pch2lan:
4079 case e1000_pch_lpt:
4080 case e1000_pch_spt:
4081 case e1000_pch_cnp:
4082 case e1000_pch_tgp:
4083 case e1000_pch_adp:
4084 fc->refresh_time = 0xFFFF;
4085 fc->pause_time = 0xFFFF;
4086
4087 if (adapter->netdev->mtu <= ETH_DATA_LEN) {
4088 fc->high_water = 0x05C20;
4089 fc->low_water = 0x05048;
4090 break;
4091 }
4092
4093 pba = 14;
4094 ew32(PBA, pba);
4095 fc->high_water = ((pba << 10) * 9 / 10) & E1000_FCRTH_RTH;
4096 fc->low_water = ((pba << 10) * 8 / 10) & E1000_FCRTL_RTL;
4097 break;
4098 }
4099
4100 /* Alignment of Tx data is on an arbitrary byte boundary with the
4101 * maximum size per Tx descriptor limited only to the transmit
4102 * allocation of the packet buffer minus 96 bytes with an upper
4103 * limit of 24KB due to receive synchronization limitations.
4104 */
4105 adapter->tx_fifo_limit = min_t(u32, ((er32(PBA) >> 16) << 10) - 96,
4106 24 << 10);
4107
4108 /* Disable Adaptive Interrupt Moderation if 2 full packets cannot
4109 * fit in receive buffer.
4110 */
4111 if (adapter->itr_setting & 0x3) {
4112 if ((adapter->max_frame_size * 2) > (pba << 10)) {
4113 if (!(adapter->flags2 & FLAG2_DISABLE_AIM)) {
4114 dev_info(&adapter->pdev->dev,
4115 "Interrupt Throttle Rate off\n");
4116 adapter->flags2 |= FLAG2_DISABLE_AIM;
4117 e1000e_write_itr(adapter, 0);
4118 }
4119 } else if (adapter->flags2 & FLAG2_DISABLE_AIM) {
4120 dev_info(&adapter->pdev->dev,
4121 "Interrupt Throttle Rate on\n");
4122 adapter->flags2 &= ~FLAG2_DISABLE_AIM;
4123 adapter->itr = 20000;
4124 e1000e_write_itr(adapter, adapter->itr);
4125 }
4126 }
4127
4128 if (hw->mac.type >= e1000_pch_spt)
4129 e1000_flush_desc_rings(adapter);
4130 /* Allow time for pending master requests to run */
4131 mac->ops.reset_hw(hw);
4132
4133 /* For parts with AMT enabled, let the firmware know
4134 * that the network interface is in control
4135 */
4136 if (adapter->flags & FLAG_HAS_AMT)
4137 e1000e_get_hw_control(adapter);
4138
4139 ew32(WUC, 0);
4140
4141 if (mac->ops.init_hw(hw))
4142 e_err("Hardware Error\n");
4143
4144 e1000_update_mng_vlan(adapter);
4145
4146 /* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */
4147 ew32(VET, ETH_P_8021Q);
4148
4149 e1000e_reset_adaptive(hw);
4150
4151 /* restore systim and hwtstamp settings */
4152 e1000e_systim_reset(adapter);
4153
4154 /* Set EEE advertisement as appropriate */
4155 if (adapter->flags2 & FLAG2_HAS_EEE) {
4156 s32 ret_val;
4157 u16 adv_addr;
4158
4159 switch (hw->phy.type) {
4160 case e1000_phy_82579:
4161 adv_addr = I82579_EEE_ADVERTISEMENT;
4162 break;
4163 case e1000_phy_i217:
4164 adv_addr = I217_EEE_ADVERTISEMENT;
4165 break;
4166 default:
4167 dev_err(&adapter->pdev->dev,
4168 "Invalid PHY type setting EEE advertisement\n");
4169 return;
4170 }
4171
4172 ret_val = hw->phy.ops.acquire(hw);
4173 if (ret_val) {
4174 dev_err(&adapter->pdev->dev,
4175 "EEE advertisement - unable to acquire PHY\n");
4176 return;
4177 }
4178
4179 e1000_write_emi_reg_locked(hw, adv_addr,
4180 hw->dev_spec.ich8lan.eee_disable ?
4181 0 : adapter->eee_advert);
4182
4183 hw->phy.ops.release(hw);
4184 }
4185
4186 if (!netif_running(adapter->netdev) &&
4187 !test_bit(__E1000_TESTING, &adapter->state))
4188 e1000_power_down_phy(adapter);
4189
4190 e1000_get_phy_info(hw);
4191
4192 if ((adapter->flags & FLAG_HAS_SMART_POWER_DOWN) &&
4193 !(adapter->flags & FLAG_SMART_POWER_DOWN)) {
4194 u16 phy_data = 0;
4195 /* speed up time to link by disabling smart power down, ignore
4196 * the return value of this function because there is nothing
4197 * different we would do if it failed
4198 */
4199 e1e_rphy(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
4200 phy_data &= ~IGP02E1000_PM_SPD;
4201 e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
4202 }
4203 if (hw->mac.type >= e1000_pch_spt && adapter->int_mode == 0) {
4204 u32 reg;
4205
4206 /* Fextnvm7 @ 0xe4[2] = 1 */
4207 reg = er32(FEXTNVM7);
4208 reg |= E1000_FEXTNVM7_SIDE_CLK_UNGATE;
4209 ew32(FEXTNVM7, reg);
4210 /* Fextnvm9 @ 0x5bb4[13:12] = 11 */
4211 reg = er32(FEXTNVM9);
4212 reg |= E1000_FEXTNVM9_IOSFSB_CLKGATE_DIS |
4213 E1000_FEXTNVM9_IOSFSB_CLKREQ_DIS;
4214 ew32(FEXTNVM9, reg);
4215 }
4216
4217}
4218
4219/**
4220 * e1000e_trigger_lsc - trigger an LSC interrupt
4221 * @adapter:
4222 *
4223 * Fire a link status change interrupt to start the watchdog.
4224 **/
4225static void e1000e_trigger_lsc(struct e1000_adapter *adapter)
4226{
4227 struct e1000_hw *hw = &adapter->hw;
4228
4229 if (adapter->msix_entries)
4230 ew32(ICS, E1000_ICS_LSC | E1000_ICS_OTHER);
4231 else
4232 ew32(ICS, E1000_ICS_LSC);
4233}
4234
4235void e1000e_up(struct e1000_adapter *adapter)
4236{
4237 /* hardware has been reset, we need to reload some things */
4238 e1000_configure(adapter);
4239
4240 clear_bit(__E1000_DOWN, &adapter->state);
4241
4242 if (adapter->msix_entries)
4243 e1000_configure_msix(adapter);
4244 e1000_irq_enable(adapter);
4245
4246 /* Tx queue started by watchdog timer when link is up */
4247
4248 e1000e_trigger_lsc(adapter);
4249}
4250
4251static void e1000e_flush_descriptors(struct e1000_adapter *adapter)
4252{
4253 struct e1000_hw *hw = &adapter->hw;
4254
4255 if (!(adapter->flags2 & FLAG2_DMA_BURST))
4256 return;
4257
4258 /* flush pending descriptor writebacks to memory */
4259 ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD);
4260 ew32(RDTR, adapter->rx_int_delay | E1000_RDTR_FPD);
4261
4262 /* execute the writes immediately */
4263 e1e_flush();
4264
4265 /* due to rare timing issues, write to TIDV/RDTR again to ensure the
4266 * write is successful
4267 */
4268 ew32(TIDV, adapter->tx_int_delay | E1000_TIDV_FPD);
4269 ew32(RDTR, adapter->rx_int_delay | E1000_RDTR_FPD);
4270
4271 /* execute the writes immediately */
4272 e1e_flush();
4273}
4274
4275static void e1000e_update_stats(struct e1000_adapter *adapter);
4276
4277/**
4278 * e1000e_down - quiesce the device and optionally reset the hardware
4279 * @adapter: board private structure
4280 * @reset: boolean flag to reset the hardware or not
4281 */
4282void e1000e_down(struct e1000_adapter *adapter, bool reset)
4283{
4284 struct net_device *netdev = adapter->netdev;
4285 struct e1000_hw *hw = &adapter->hw;
4286 u32 tctl, rctl;
4287
4288 /* signal that we're down so the interrupt handler does not
4289 * reschedule our watchdog timer
4290 */
4291 set_bit(__E1000_DOWN, &adapter->state);
4292
4293 netif_carrier_off(netdev);
4294
4295 /* disable receives in the hardware */
4296 rctl = er32(RCTL);
4297 if (!(adapter->flags2 & FLAG2_NO_DISABLE_RX))
4298 ew32(RCTL, rctl & ~E1000_RCTL_EN);
4299 /* flush and sleep below */
4300
4301 netif_stop_queue(netdev);
4302
4303 /* disable transmits in the hardware */
4304 tctl = er32(TCTL);
4305 tctl &= ~E1000_TCTL_EN;
4306 ew32(TCTL, tctl);
4307
4308 /* flush both disables and wait for them to finish */
4309 e1e_flush();
4310 usleep_range(10000, 11000);
4311
4312 e1000_irq_disable(adapter);
4313
4314 napi_synchronize(&adapter->napi);
4315
4316 del_timer_sync(&adapter->watchdog_timer);
4317 del_timer_sync(&adapter->phy_info_timer);
4318
4319 spin_lock(&adapter->stats64_lock);
4320 e1000e_update_stats(adapter);
4321 spin_unlock(&adapter->stats64_lock);
4322
4323 e1000e_flush_descriptors(adapter);
4324
4325 adapter->link_speed = 0;
4326 adapter->link_duplex = 0;
4327
4328 /* Disable Si errata workaround on PCHx for jumbo frame flow */
4329 if ((hw->mac.type >= e1000_pch2lan) &&
4330 (adapter->netdev->mtu > ETH_DATA_LEN) &&
4331 e1000_lv_jumbo_workaround_ich8lan(hw, false))
4332 e_dbg("failed to disable jumbo frame workaround mode\n");
4333
4334 if (!pci_channel_offline(adapter->pdev)) {
4335 if (reset)
4336 e1000e_reset(adapter);
4337 else if (hw->mac.type >= e1000_pch_spt)
4338 e1000_flush_desc_rings(adapter);
4339 }
4340 e1000_clean_tx_ring(adapter->tx_ring);
4341 e1000_clean_rx_ring(adapter->rx_ring);
4342}
4343
4344void e1000e_reinit_locked(struct e1000_adapter *adapter)
4345{
4346 might_sleep();
4347 while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
4348 usleep_range(1000, 1100);
4349 e1000e_down(adapter, true);
4350 e1000e_up(adapter);
4351 clear_bit(__E1000_RESETTING, &adapter->state);
4352}
4353
4354/**
4355 * e1000e_sanitize_systim - sanitize raw cycle counter reads
4356 * @hw: pointer to the HW structure
4357 * @systim: PHC time value read, sanitized and returned
4358 * @sts: structure to hold system time before and after reading SYSTIML,
4359 * may be NULL
4360 *
4361 * Errata for 82574/82583 possible bad bits read from SYSTIMH/L:
4362 * check to see that the time is incrementing at a reasonable
4363 * rate and is a multiple of incvalue.
4364 **/
4365static u64 e1000e_sanitize_systim(struct e1000_hw *hw, u64 systim,
4366 struct ptp_system_timestamp *sts)
4367{
4368 u64 time_delta, rem, temp;
4369 u64 systim_next;
4370 u32 incvalue;
4371 int i;
4372
4373 incvalue = er32(TIMINCA) & E1000_TIMINCA_INCVALUE_MASK;
4374 for (i = 0; i < E1000_MAX_82574_SYSTIM_REREADS; i++) {
4375 /* latch SYSTIMH on read of SYSTIML */
4376 ptp_read_system_prets(sts);
4377 systim_next = (u64)er32(SYSTIML);
4378 ptp_read_system_postts(sts);
4379 systim_next |= (u64)er32(SYSTIMH) << 32;
4380
4381 time_delta = systim_next - systim;
4382 temp = time_delta;
4383 /* VMWare users have seen incvalue of zero, don't div / 0 */
4384 rem = incvalue ? do_div(temp, incvalue) : (time_delta != 0);
4385
4386 systim = systim_next;
4387
4388 if ((time_delta < E1000_82574_SYSTIM_EPSILON) && (rem == 0))
4389 break;
4390 }
4391
4392 return systim;
4393}
4394
4395/**
4396 * e1000e_read_systim - read SYSTIM register
4397 * @adapter: board private structure
4398 * @sts: structure which will contain system time before and after reading
4399 * SYSTIML, may be NULL
4400 **/
4401u64 e1000e_read_systim(struct e1000_adapter *adapter,
4402 struct ptp_system_timestamp *sts)
4403{
4404 struct e1000_hw *hw = &adapter->hw;
4405 u32 systimel, systimel_2, systimeh;
4406 u64 systim;
4407 /* SYSTIMH latching upon SYSTIML read does not work well.
4408 * This means that if SYSTIML overflows after we read it but before
4409 * we read SYSTIMH, the value of SYSTIMH has been incremented and we
4410 * will experience a huge non linear increment in the systime value
4411 * to fix that we test for overflow and if true, we re-read systime.
4412 */
4413 ptp_read_system_prets(sts);
4414 systimel = er32(SYSTIML);
4415 ptp_read_system_postts(sts);
4416 systimeh = er32(SYSTIMH);
4417 /* Is systimel is so large that overflow is possible? */
4418 if (systimel >= (u32)0xffffffff - E1000_TIMINCA_INCVALUE_MASK) {
4419 ptp_read_system_prets(sts);
4420 systimel_2 = er32(SYSTIML);
4421 ptp_read_system_postts(sts);
4422 if (systimel > systimel_2) {
4423 /* There was an overflow, read again SYSTIMH, and use
4424 * systimel_2
4425 */
4426 systimeh = er32(SYSTIMH);
4427 systimel = systimel_2;
4428 }
4429 }
4430 systim = (u64)systimel;
4431 systim |= (u64)systimeh << 32;
4432
4433 if (adapter->flags2 & FLAG2_CHECK_SYSTIM_OVERFLOW)
4434 systim = e1000e_sanitize_systim(hw, systim, sts);
4435
4436 return systim;
4437}
4438
4439/**
4440 * e1000e_cyclecounter_read - read raw cycle counter (used by time counter)
4441 * @cc: cyclecounter structure
4442 **/
4443static u64 e1000e_cyclecounter_read(const struct cyclecounter *cc)
4444{
4445 struct e1000_adapter *adapter = container_of(cc, struct e1000_adapter,
4446 cc);
4447
4448 return e1000e_read_systim(adapter, NULL);
4449}
4450
4451/**
4452 * e1000_sw_init - Initialize general software structures (struct e1000_adapter)
4453 * @adapter: board private structure to initialize
4454 *
4455 * e1000_sw_init initializes the Adapter private data structure.
4456 * Fields are initialized based on PCI device information and
4457 * OS network device settings (MTU size).
4458 **/
4459static int e1000_sw_init(struct e1000_adapter *adapter)
4460{
4461 struct net_device *netdev = adapter->netdev;
4462
4463 adapter->rx_buffer_len = VLAN_ETH_FRAME_LEN + ETH_FCS_LEN;
4464 adapter->rx_ps_bsize0 = 128;
4465 adapter->max_frame_size = netdev->mtu + VLAN_ETH_HLEN + ETH_FCS_LEN;
4466 adapter->min_frame_size = ETH_ZLEN + ETH_FCS_LEN;
4467 adapter->tx_ring_count = E1000_DEFAULT_TXD;
4468 adapter->rx_ring_count = E1000_DEFAULT_RXD;
4469
4470 spin_lock_init(&adapter->stats64_lock);
4471
4472 e1000e_set_interrupt_capability(adapter);
4473
4474 if (e1000_alloc_queues(adapter))
4475 return -ENOMEM;
4476
4477 /* Setup hardware time stamping cyclecounter */
4478 if (adapter->flags & FLAG_HAS_HW_TIMESTAMP) {
4479 adapter->cc.read = e1000e_cyclecounter_read;
4480 adapter->cc.mask = CYCLECOUNTER_MASK(64);
4481 adapter->cc.mult = 1;
4482 /* cc.shift set in e1000e_get_base_tininca() */
4483
4484 spin_lock_init(&adapter->systim_lock);
4485 INIT_WORK(&adapter->tx_hwtstamp_work, e1000e_tx_hwtstamp_work);
4486 }
4487
4488 /* Explicitly disable IRQ since the NIC can be in any state. */
4489 e1000_irq_disable(adapter);
4490
4491 set_bit(__E1000_DOWN, &adapter->state);
4492 return 0;
4493}
4494
4495/**
4496 * e1000_intr_msi_test - Interrupt Handler
4497 * @irq: interrupt number
4498 * @data: pointer to a network interface device structure
4499 **/
4500static irqreturn_t e1000_intr_msi_test(int __always_unused irq, void *data)
4501{
4502 struct net_device *netdev = data;
4503 struct e1000_adapter *adapter = netdev_priv(netdev);
4504 struct e1000_hw *hw = &adapter->hw;
4505 u32 icr = er32(ICR);
4506
4507 e_dbg("icr is %08X\n", icr);
4508 if (icr & E1000_ICR_RXSEQ) {
4509 adapter->flags &= ~FLAG_MSI_TEST_FAILED;
4510 /* Force memory writes to complete before acknowledging the
4511 * interrupt is handled.
4512 */
4513 wmb();
4514 }
4515
4516 return IRQ_HANDLED;
4517}
4518
4519/**
4520 * e1000_test_msi_interrupt - Returns 0 for successful test
4521 * @adapter: board private struct
4522 *
4523 * code flow taken from tg3.c
4524 **/
4525static int e1000_test_msi_interrupt(struct e1000_adapter *adapter)
4526{
4527 struct net_device *netdev = adapter->netdev;
4528 struct e1000_hw *hw = &adapter->hw;
4529 int err;
4530
4531 /* poll_enable hasn't been called yet, so don't need disable */
4532 /* clear any pending events */
4533 er32(ICR);
4534
4535 /* free the real vector and request a test handler */
4536 e1000_free_irq(adapter);
4537 e1000e_reset_interrupt_capability(adapter);
4538
4539 /* Assume that the test fails, if it succeeds then the test
4540 * MSI irq handler will unset this flag
4541 */
4542 adapter->flags |= FLAG_MSI_TEST_FAILED;
4543
4544 err = pci_enable_msi(adapter->pdev);
4545 if (err)
4546 goto msi_test_failed;
4547
4548 err = request_irq(adapter->pdev->irq, e1000_intr_msi_test, 0,
4549 netdev->name, netdev);
4550 if (err) {
4551 pci_disable_msi(adapter->pdev);
4552 goto msi_test_failed;
4553 }
4554
4555 /* Force memory writes to complete before enabling and firing an
4556 * interrupt.
4557 */
4558 wmb();
4559
4560 e1000_irq_enable(adapter);
4561
4562 /* fire an unusual interrupt on the test handler */
4563 ew32(ICS, E1000_ICS_RXSEQ);
4564 e1e_flush();
4565 msleep(100);
4566
4567 e1000_irq_disable(adapter);
4568
4569 rmb(); /* read flags after interrupt has been fired */
4570
4571 if (adapter->flags & FLAG_MSI_TEST_FAILED) {
4572 adapter->int_mode = E1000E_INT_MODE_LEGACY;
4573 e_info("MSI interrupt test failed, using legacy interrupt.\n");
4574 } else {
4575 e_dbg("MSI interrupt test succeeded!\n");
4576 }
4577
4578 free_irq(adapter->pdev->irq, netdev);
4579 pci_disable_msi(adapter->pdev);
4580
4581msi_test_failed:
4582 e1000e_set_interrupt_capability(adapter);
4583 return e1000_request_irq(adapter);
4584}
4585
4586/**
4587 * e1000_test_msi - Returns 0 if MSI test succeeds or INTx mode is restored
4588 * @adapter: board private struct
4589 *
4590 * code flow taken from tg3.c, called with e1000 interrupts disabled.
4591 **/
4592static int e1000_test_msi(struct e1000_adapter *adapter)
4593{
4594 int err;
4595 u16 pci_cmd;
4596
4597 if (!(adapter->flags & FLAG_MSI_ENABLED))
4598 return 0;
4599
4600 /* disable SERR in case the MSI write causes a master abort */
4601 pci_read_config_word(adapter->pdev, PCI_COMMAND, &pci_cmd);
4602 if (pci_cmd & PCI_COMMAND_SERR)
4603 pci_write_config_word(adapter->pdev, PCI_COMMAND,
4604 pci_cmd & ~PCI_COMMAND_SERR);
4605
4606 err = e1000_test_msi_interrupt(adapter);
4607
4608 /* re-enable SERR */
4609 if (pci_cmd & PCI_COMMAND_SERR) {
4610 pci_read_config_word(adapter->pdev, PCI_COMMAND, &pci_cmd);
4611 pci_cmd |= PCI_COMMAND_SERR;
4612 pci_write_config_word(adapter->pdev, PCI_COMMAND, pci_cmd);
4613 }
4614
4615 return err;
4616}
4617
4618/**
4619 * e1000e_open - Called when a network interface is made active
4620 * @netdev: network interface device structure
4621 *
4622 * Returns 0 on success, negative value on failure
4623 *
4624 * The open entry point is called when a network interface is made
4625 * active by the system (IFF_UP). At this point all resources needed
4626 * for transmit and receive operations are allocated, the interrupt
4627 * handler is registered with the OS, the watchdog timer is started,
4628 * and the stack is notified that the interface is ready.
4629 **/
4630int e1000e_open(struct net_device *netdev)
4631{
4632 struct e1000_adapter *adapter = netdev_priv(netdev);
4633 struct e1000_hw *hw = &adapter->hw;
4634 struct pci_dev *pdev = adapter->pdev;
4635 int err;
4636
4637 /* disallow open during test */
4638 if (test_bit(__E1000_TESTING, &adapter->state))
4639 return -EBUSY;
4640
4641 pm_runtime_get_sync(&pdev->dev);
4642
4643 netif_carrier_off(netdev);
4644 netif_stop_queue(netdev);
4645
4646 /* allocate transmit descriptors */
4647 err = e1000e_setup_tx_resources(adapter->tx_ring);
4648 if (err)
4649 goto err_setup_tx;
4650
4651 /* allocate receive descriptors */
4652 err = e1000e_setup_rx_resources(adapter->rx_ring);
4653 if (err)
4654 goto err_setup_rx;
4655
4656 /* If AMT is enabled, let the firmware know that the network
4657 * interface is now open and reset the part to a known state.
4658 */
4659 if (adapter->flags & FLAG_HAS_AMT) {
4660 e1000e_get_hw_control(adapter);
4661 e1000e_reset(adapter);
4662 }
4663
4664 e1000e_power_up_phy(adapter);
4665
4666 adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
4667 if ((adapter->hw.mng_cookie.status & E1000_MNG_DHCP_COOKIE_STATUS_VLAN))
4668 e1000_update_mng_vlan(adapter);
4669
4670 /* DMA latency requirement to workaround jumbo issue */
4671 cpu_latency_qos_add_request(&adapter->pm_qos_req, PM_QOS_DEFAULT_VALUE);
4672
4673 /* before we allocate an interrupt, we must be ready to handle it.
4674 * Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt
4675 * as soon as we call pci_request_irq, so we have to setup our
4676 * clean_rx handler before we do so.
4677 */
4678 e1000_configure(adapter);
4679
4680 err = e1000_request_irq(adapter);
4681 if (err)
4682 goto err_req_irq;
4683
4684 /* Work around PCIe errata with MSI interrupts causing some chipsets to
4685 * ignore e1000e MSI messages, which means we need to test our MSI
4686 * interrupt now
4687 */
4688 if (adapter->int_mode != E1000E_INT_MODE_LEGACY) {
4689 err = e1000_test_msi(adapter);
4690 if (err) {
4691 e_err("Interrupt allocation failed\n");
4692 goto err_req_irq;
4693 }
4694 }
4695
4696 /* From here on the code is the same as e1000e_up() */
4697 clear_bit(__E1000_DOWN, &adapter->state);
4698
4699 napi_enable(&adapter->napi);
4700
4701 e1000_irq_enable(adapter);
4702
4703 adapter->tx_hang_recheck = false;
4704
4705 hw->mac.get_link_status = true;
4706 pm_runtime_put(&pdev->dev);
4707
4708 e1000e_trigger_lsc(adapter);
4709
4710 return 0;
4711
4712err_req_irq:
4713 cpu_latency_qos_remove_request(&adapter->pm_qos_req);
4714 e1000e_release_hw_control(adapter);
4715 e1000_power_down_phy(adapter);
4716 e1000e_free_rx_resources(adapter->rx_ring);
4717err_setup_rx:
4718 e1000e_free_tx_resources(adapter->tx_ring);
4719err_setup_tx:
4720 e1000e_reset(adapter);
4721 pm_runtime_put_sync(&pdev->dev);
4722
4723 return err;
4724}
4725
4726/**
4727 * e1000e_close - Disables a network interface
4728 * @netdev: network interface device structure
4729 *
4730 * Returns 0, this is not allowed to fail
4731 *
4732 * The close entry point is called when an interface is de-activated
4733 * by the OS. The hardware is still under the drivers control, but
4734 * needs to be disabled. A global MAC reset is issued to stop the
4735 * hardware, and all transmit and receive resources are freed.
4736 **/
4737int e1000e_close(struct net_device *netdev)
4738{
4739 struct e1000_adapter *adapter = netdev_priv(netdev);
4740 struct pci_dev *pdev = adapter->pdev;
4741 int count = E1000_CHECK_RESET_COUNT;
4742
4743 while (test_bit(__E1000_RESETTING, &adapter->state) && count--)
4744 usleep_range(10000, 11000);
4745
4746 WARN_ON(test_bit(__E1000_RESETTING, &adapter->state));
4747
4748 pm_runtime_get_sync(&pdev->dev);
4749
4750 if (netif_device_present(netdev)) {
4751 e1000e_down(adapter, true);
4752 e1000_free_irq(adapter);
4753
4754 /* Link status message must follow this format */
4755 netdev_info(netdev, "NIC Link is Down\n");
4756 }
4757
4758 napi_disable(&adapter->napi);
4759
4760 e1000e_free_tx_resources(adapter->tx_ring);
4761 e1000e_free_rx_resources(adapter->rx_ring);
4762
4763 /* kill manageability vlan ID if supported, but not if a vlan with
4764 * the same ID is registered on the host OS (let 8021q kill it)
4765 */
4766 if (adapter->hw.mng_cookie.status & E1000_MNG_DHCP_COOKIE_STATUS_VLAN)
4767 e1000_vlan_rx_kill_vid(netdev, htons(ETH_P_8021Q),
4768 adapter->mng_vlan_id);
4769
4770 /* If AMT is enabled, let the firmware know that the network
4771 * interface is now closed
4772 */
4773 if ((adapter->flags & FLAG_HAS_AMT) &&
4774 !test_bit(__E1000_TESTING, &adapter->state))
4775 e1000e_release_hw_control(adapter);
4776
4777 cpu_latency_qos_remove_request(&adapter->pm_qos_req);
4778
4779 pm_runtime_put_sync(&pdev->dev);
4780
4781 return 0;
4782}
4783
4784/**
4785 * e1000_set_mac - Change the Ethernet Address of the NIC
4786 * @netdev: network interface device structure
4787 * @p: pointer to an address structure
4788 *
4789 * Returns 0 on success, negative on failure
4790 **/
4791static int e1000_set_mac(struct net_device *netdev, void *p)
4792{
4793 struct e1000_adapter *adapter = netdev_priv(netdev);
4794 struct e1000_hw *hw = &adapter->hw;
4795 struct sockaddr *addr = p;
4796
4797 if (!is_valid_ether_addr(addr->sa_data))
4798 return -EADDRNOTAVAIL;
4799
4800 memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
4801 memcpy(adapter->hw.mac.addr, addr->sa_data, netdev->addr_len);
4802
4803 hw->mac.ops.rar_set(&adapter->hw, adapter->hw.mac.addr, 0);
4804
4805 if (adapter->flags & FLAG_RESET_OVERWRITES_LAA) {
4806 /* activate the work around */
4807 e1000e_set_laa_state_82571(&adapter->hw, 1);
4808
4809 /* Hold a copy of the LAA in RAR[14] This is done so that
4810 * between the time RAR[0] gets clobbered and the time it
4811 * gets fixed (in e1000_watchdog), the actual LAA is in one
4812 * of the RARs and no incoming packets directed to this port
4813 * are dropped. Eventually the LAA will be in RAR[0] and
4814 * RAR[14]
4815 */
4816 hw->mac.ops.rar_set(&adapter->hw, adapter->hw.mac.addr,
4817 adapter->hw.mac.rar_entry_count - 1);
4818 }
4819
4820 return 0;
4821}
4822
4823/**
4824 * e1000e_update_phy_task - work thread to update phy
4825 * @work: pointer to our work struct
4826 *
4827 * this worker thread exists because we must acquire a
4828 * semaphore to read the phy, which we could msleep while
4829 * waiting for it, and we can't msleep in a timer.
4830 **/
4831static void e1000e_update_phy_task(struct work_struct *work)
4832{
4833 struct e1000_adapter *adapter = container_of(work,
4834 struct e1000_adapter,
4835 update_phy_task);
4836 struct e1000_hw *hw = &adapter->hw;
4837
4838 if (test_bit(__E1000_DOWN, &adapter->state))
4839 return;
4840
4841 e1000_get_phy_info(hw);
4842
4843 /* Enable EEE on 82579 after link up */
4844 if (hw->phy.type >= e1000_phy_82579)
4845 e1000_set_eee_pchlan(hw);
4846}
4847
4848/**
4849 * e1000_update_phy_info - timre call-back to update PHY info
4850 * @data: pointer to adapter cast into an unsigned long
4851 *
4852 * Need to wait a few seconds after link up to get diagnostic information from
4853 * the phy
4854 **/
4855static void e1000_update_phy_info(struct timer_list *t)
4856{
4857 struct e1000_adapter *adapter = from_timer(adapter, t, phy_info_timer);
4858
4859 if (test_bit(__E1000_DOWN, &adapter->state))
4860 return;
4861
4862 schedule_work(&adapter->update_phy_task);
4863}
4864
4865/**
4866 * e1000e_update_phy_stats - Update the PHY statistics counters
4867 * @adapter: board private structure
4868 *
4869 * Read/clear the upper 16-bit PHY registers and read/accumulate lower
4870 **/
4871static void e1000e_update_phy_stats(struct e1000_adapter *adapter)
4872{
4873 struct e1000_hw *hw = &adapter->hw;
4874 s32 ret_val;
4875 u16 phy_data;
4876
4877 ret_val = hw->phy.ops.acquire(hw);
4878 if (ret_val)
4879 return;
4880
4881 /* A page set is expensive so check if already on desired page.
4882 * If not, set to the page with the PHY status registers.
4883 */
4884 hw->phy.addr = 1;
4885 ret_val = e1000e_read_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
4886 &phy_data);
4887 if (ret_val)
4888 goto release;
4889 if (phy_data != (HV_STATS_PAGE << IGP_PAGE_SHIFT)) {
4890 ret_val = hw->phy.ops.set_page(hw,
4891 HV_STATS_PAGE << IGP_PAGE_SHIFT);
4892 if (ret_val)
4893 goto release;
4894 }
4895
4896 /* Single Collision Count */
4897 hw->phy.ops.read_reg_page(hw, HV_SCC_UPPER, &phy_data);
4898 ret_val = hw->phy.ops.read_reg_page(hw, HV_SCC_LOWER, &phy_data);
4899 if (!ret_val)
4900 adapter->stats.scc += phy_data;
4901
4902 /* Excessive Collision Count */
4903 hw->phy.ops.read_reg_page(hw, HV_ECOL_UPPER, &phy_data);
4904 ret_val = hw->phy.ops.read_reg_page(hw, HV_ECOL_LOWER, &phy_data);
4905 if (!ret_val)
4906 adapter->stats.ecol += phy_data;
4907
4908 /* Multiple Collision Count */
4909 hw->phy.ops.read_reg_page(hw, HV_MCC_UPPER, &phy_data);
4910 ret_val = hw->phy.ops.read_reg_page(hw, HV_MCC_LOWER, &phy_data);
4911 if (!ret_val)
4912 adapter->stats.mcc += phy_data;
4913
4914 /* Late Collision Count */
4915 hw->phy.ops.read_reg_page(hw, HV_LATECOL_UPPER, &phy_data);
4916 ret_val = hw->phy.ops.read_reg_page(hw, HV_LATECOL_LOWER, &phy_data);
4917 if (!ret_val)
4918 adapter->stats.latecol += phy_data;
4919
4920 /* Collision Count - also used for adaptive IFS */
4921 hw->phy.ops.read_reg_page(hw, HV_COLC_UPPER, &phy_data);
4922 ret_val = hw->phy.ops.read_reg_page(hw, HV_COLC_LOWER, &phy_data);
4923 if (!ret_val)
4924 hw->mac.collision_delta = phy_data;
4925
4926 /* Defer Count */
4927 hw->phy.ops.read_reg_page(hw, HV_DC_UPPER, &phy_data);
4928 ret_val = hw->phy.ops.read_reg_page(hw, HV_DC_LOWER, &phy_data);
4929 if (!ret_val)
4930 adapter->stats.dc += phy_data;
4931
4932 /* Transmit with no CRS */
4933 hw->phy.ops.read_reg_page(hw, HV_TNCRS_UPPER, &phy_data);
4934 ret_val = hw->phy.ops.read_reg_page(hw, HV_TNCRS_LOWER, &phy_data);
4935 if (!ret_val)
4936 adapter->stats.tncrs += phy_data;
4937
4938release:
4939 hw->phy.ops.release(hw);
4940}
4941
4942/**
4943 * e1000e_update_stats - Update the board statistics counters
4944 * @adapter: board private structure
4945 **/
4946static void e1000e_update_stats(struct e1000_adapter *adapter)
4947{
4948 struct net_device *netdev = adapter->netdev;
4949 struct e1000_hw *hw = &adapter->hw;
4950 struct pci_dev *pdev = adapter->pdev;
4951
4952 /* Prevent stats update while adapter is being reset, or if the pci
4953 * connection is down.
4954 */
4955 if (adapter->link_speed == 0)
4956 return;
4957 if (pci_channel_offline(pdev))
4958 return;
4959
4960 adapter->stats.crcerrs += er32(CRCERRS);
4961 adapter->stats.gprc += er32(GPRC);
4962 adapter->stats.gorc += er32(GORCL);
4963 er32(GORCH); /* Clear gorc */
4964 adapter->stats.bprc += er32(BPRC);
4965 adapter->stats.mprc += er32(MPRC);
4966 adapter->stats.roc += er32(ROC);
4967
4968 adapter->stats.mpc += er32(MPC);
4969
4970 /* Half-duplex statistics */
4971 if (adapter->link_duplex == HALF_DUPLEX) {
4972 if (adapter->flags2 & FLAG2_HAS_PHY_STATS) {
4973 e1000e_update_phy_stats(adapter);
4974 } else {
4975 adapter->stats.scc += er32(SCC);
4976 adapter->stats.ecol += er32(ECOL);
4977 adapter->stats.mcc += er32(MCC);
4978 adapter->stats.latecol += er32(LATECOL);
4979 adapter->stats.dc += er32(DC);
4980
4981 hw->mac.collision_delta = er32(COLC);
4982
4983 if ((hw->mac.type != e1000_82574) &&
4984 (hw->mac.type != e1000_82583))
4985 adapter->stats.tncrs += er32(TNCRS);
4986 }
4987 adapter->stats.colc += hw->mac.collision_delta;
4988 }
4989
4990 adapter->stats.xonrxc += er32(XONRXC);
4991 adapter->stats.xontxc += er32(XONTXC);
4992 adapter->stats.xoffrxc += er32(XOFFRXC);
4993 adapter->stats.xofftxc += er32(XOFFTXC);
4994 adapter->stats.gptc += er32(GPTC);
4995 adapter->stats.gotc += er32(GOTCL);
4996 er32(GOTCH); /* Clear gotc */
4997 adapter->stats.rnbc += er32(RNBC);
4998 adapter->stats.ruc += er32(RUC);
4999
5000 adapter->stats.mptc += er32(MPTC);
5001 adapter->stats.bptc += er32(BPTC);
5002
5003 /* used for adaptive IFS */
5004
5005 hw->mac.tx_packet_delta = er32(TPT);
5006 adapter->stats.tpt += hw->mac.tx_packet_delta;
5007
5008 adapter->stats.algnerrc += er32(ALGNERRC);
5009 adapter->stats.rxerrc += er32(RXERRC);
5010 adapter->stats.cexterr += er32(CEXTERR);
5011 adapter->stats.tsctc += er32(TSCTC);
5012 adapter->stats.tsctfc += er32(TSCTFC);
5013
5014 /* Fill out the OS statistics structure */
5015 netdev->stats.multicast = adapter->stats.mprc;
5016 netdev->stats.collisions = adapter->stats.colc;
5017
5018 /* Rx Errors */
5019
5020 /* RLEC on some newer hardware can be incorrect so build
5021 * our own version based on RUC and ROC
5022 */
5023 netdev->stats.rx_errors = adapter->stats.rxerrc +
5024 adapter->stats.crcerrs + adapter->stats.algnerrc +
5025 adapter->stats.ruc + adapter->stats.roc + adapter->stats.cexterr;
5026 netdev->stats.rx_length_errors = adapter->stats.ruc +
5027 adapter->stats.roc;
5028 netdev->stats.rx_crc_errors = adapter->stats.crcerrs;
5029 netdev->stats.rx_frame_errors = adapter->stats.algnerrc;
5030 netdev->stats.rx_missed_errors = adapter->stats.mpc;
5031
5032 /* Tx Errors */
5033 netdev->stats.tx_errors = adapter->stats.ecol + adapter->stats.latecol;
5034 netdev->stats.tx_aborted_errors = adapter->stats.ecol;
5035 netdev->stats.tx_window_errors = adapter->stats.latecol;
5036 netdev->stats.tx_carrier_errors = adapter->stats.tncrs;
5037
5038 /* Tx Dropped needs to be maintained elsewhere */
5039
5040 /* Management Stats */
5041 adapter->stats.mgptc += er32(MGTPTC);
5042 adapter->stats.mgprc += er32(MGTPRC);
5043 adapter->stats.mgpdc += er32(MGTPDC);
5044
5045 /* Correctable ECC Errors */
5046 if (hw->mac.type >= e1000_pch_lpt) {
5047 u32 pbeccsts = er32(PBECCSTS);
5048
5049 adapter->corr_errors +=
5050 pbeccsts & E1000_PBECCSTS_CORR_ERR_CNT_MASK;
5051 adapter->uncorr_errors +=
5052 (pbeccsts & E1000_PBECCSTS_UNCORR_ERR_CNT_MASK) >>
5053 E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT;
5054 }
5055}
5056
5057/**
5058 * e1000_phy_read_status - Update the PHY register status snapshot
5059 * @adapter: board private structure
5060 **/
5061static void e1000_phy_read_status(struct e1000_adapter *adapter)
5062{
5063 struct e1000_hw *hw = &adapter->hw;
5064 struct e1000_phy_regs *phy = &adapter->phy_regs;
5065
5066 if (!pm_runtime_suspended((&adapter->pdev->dev)->parent) &&
5067 (er32(STATUS) & E1000_STATUS_LU) &&
5068 (adapter->hw.phy.media_type == e1000_media_type_copper)) {
5069 int ret_val;
5070
5071 ret_val = e1e_rphy(hw, MII_BMCR, &phy->bmcr);
5072 ret_val |= e1e_rphy(hw, MII_BMSR, &phy->bmsr);
5073 ret_val |= e1e_rphy(hw, MII_ADVERTISE, &phy->advertise);
5074 ret_val |= e1e_rphy(hw, MII_LPA, &phy->lpa);
5075 ret_val |= e1e_rphy(hw, MII_EXPANSION, &phy->expansion);
5076 ret_val |= e1e_rphy(hw, MII_CTRL1000, &phy->ctrl1000);
5077 ret_val |= e1e_rphy(hw, MII_STAT1000, &phy->stat1000);
5078 ret_val |= e1e_rphy(hw, MII_ESTATUS, &phy->estatus);
5079 if (ret_val)
5080 e_warn("Error reading PHY register\n");
5081 } else {
5082 /* Do not read PHY registers if link is not up
5083 * Set values to typical power-on defaults
5084 */
5085 phy->bmcr = (BMCR_SPEED1000 | BMCR_ANENABLE | BMCR_FULLDPLX);
5086 phy->bmsr = (BMSR_100FULL | BMSR_100HALF | BMSR_10FULL |
5087 BMSR_10HALF | BMSR_ESTATEN | BMSR_ANEGCAPABLE |
5088 BMSR_ERCAP);
5089 phy->advertise = (ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP |
5090 ADVERTISE_ALL | ADVERTISE_CSMA);
5091 phy->lpa = 0;
5092 phy->expansion = EXPANSION_ENABLENPAGE;
5093 phy->ctrl1000 = ADVERTISE_1000FULL;
5094 phy->stat1000 = 0;
5095 phy->estatus = (ESTATUS_1000_TFULL | ESTATUS_1000_THALF);
5096 }
5097}
5098
5099static void e1000_print_link_info(struct e1000_adapter *adapter)
5100{
5101 struct e1000_hw *hw = &adapter->hw;
5102 u32 ctrl = er32(CTRL);
5103
5104 /* Link status message must follow this format for user tools */
5105 netdev_info(adapter->netdev,
5106 "NIC Link is Up %d Mbps %s Duplex, Flow Control: %s\n",
5107 adapter->link_speed,
5108 adapter->link_duplex == FULL_DUPLEX ? "Full" : "Half",
5109 (ctrl & E1000_CTRL_TFCE) && (ctrl & E1000_CTRL_RFCE) ? "Rx/Tx" :
5110 (ctrl & E1000_CTRL_RFCE) ? "Rx" :
5111 (ctrl & E1000_CTRL_TFCE) ? "Tx" : "None");
5112}
5113
5114static bool e1000e_has_link(struct e1000_adapter *adapter)
5115{
5116 struct e1000_hw *hw = &adapter->hw;
5117 bool link_active = false;
5118 s32 ret_val = 0;
5119
5120 /* get_link_status is set on LSC (link status) interrupt or
5121 * Rx sequence error interrupt. get_link_status will stay
5122 * true until the check_for_link establishes link
5123 * for copper adapters ONLY
5124 */
5125 switch (hw->phy.media_type) {
5126 case e1000_media_type_copper:
5127 if (hw->mac.get_link_status) {
5128 ret_val = hw->mac.ops.check_for_link(hw);
5129 link_active = !hw->mac.get_link_status;
5130 } else {
5131 link_active = true;
5132 }
5133 break;
5134 case e1000_media_type_fiber:
5135 ret_val = hw->mac.ops.check_for_link(hw);
5136 link_active = !!(er32(STATUS) & E1000_STATUS_LU);
5137 break;
5138 case e1000_media_type_internal_serdes:
5139 ret_val = hw->mac.ops.check_for_link(hw);
5140 link_active = hw->mac.serdes_has_link;
5141 break;
5142 default:
5143 case e1000_media_type_unknown:
5144 break;
5145 }
5146
5147 if ((ret_val == -E1000_ERR_PHY) && (hw->phy.type == e1000_phy_igp_3) &&
5148 (er32(CTRL) & E1000_PHY_CTRL_GBE_DISABLE)) {
5149 /* See e1000_kmrn_lock_loss_workaround_ich8lan() */
5150 e_info("Gigabit has been disabled, downgrading speed\n");
5151 }
5152
5153 return link_active;
5154}
5155
5156static void e1000e_enable_receives(struct e1000_adapter *adapter)
5157{
5158 /* make sure the receive unit is started */
5159 if ((adapter->flags & FLAG_RX_NEEDS_RESTART) &&
5160 (adapter->flags & FLAG_RESTART_NOW)) {
5161 struct e1000_hw *hw = &adapter->hw;
5162 u32 rctl = er32(RCTL);
5163
5164 ew32(RCTL, rctl | E1000_RCTL_EN);
5165 adapter->flags &= ~FLAG_RESTART_NOW;
5166 }
5167}
5168
5169static void e1000e_check_82574_phy_workaround(struct e1000_adapter *adapter)
5170{
5171 struct e1000_hw *hw = &adapter->hw;
5172
5173 /* With 82574 controllers, PHY needs to be checked periodically
5174 * for hung state and reset, if two calls return true
5175 */
5176 if (e1000_check_phy_82574(hw))
5177 adapter->phy_hang_count++;
5178 else
5179 adapter->phy_hang_count = 0;
5180
5181 if (adapter->phy_hang_count > 1) {
5182 adapter->phy_hang_count = 0;
5183 e_dbg("PHY appears hung - resetting\n");
5184 schedule_work(&adapter->reset_task);
5185 }
5186}
5187
5188/**
5189 * e1000_watchdog - Timer Call-back
5190 * @data: pointer to adapter cast into an unsigned long
5191 **/
5192static void e1000_watchdog(struct timer_list *t)
5193{
5194 struct e1000_adapter *adapter = from_timer(adapter, t, watchdog_timer);
5195
5196 /* Do the rest outside of interrupt context */
5197 schedule_work(&adapter->watchdog_task);
5198
5199 /* TODO: make this use queue_delayed_work() */
5200}
5201
5202static void e1000_watchdog_task(struct work_struct *work)
5203{
5204 struct e1000_adapter *adapter = container_of(work,
5205 struct e1000_adapter,
5206 watchdog_task);
5207 struct net_device *netdev = adapter->netdev;
5208 struct e1000_mac_info *mac = &adapter->hw.mac;
5209 struct e1000_phy_info *phy = &adapter->hw.phy;
5210 struct e1000_ring *tx_ring = adapter->tx_ring;
5211 u32 dmoff_exit_timeout = 100, tries = 0;
5212 struct e1000_hw *hw = &adapter->hw;
5213 u32 link, tctl, pcim_state;
5214
5215 if (test_bit(__E1000_DOWN, &adapter->state))
5216 return;
5217
5218 link = e1000e_has_link(adapter);
5219 if ((netif_carrier_ok(netdev)) && link) {
5220 /* Cancel scheduled suspend requests. */
5221 pm_runtime_resume(netdev->dev.parent);
5222
5223 e1000e_enable_receives(adapter);
5224 goto link_up;
5225 }
5226
5227 if ((e1000e_enable_tx_pkt_filtering(hw)) &&
5228 (adapter->mng_vlan_id != adapter->hw.mng_cookie.vlan_id))
5229 e1000_update_mng_vlan(adapter);
5230
5231 if (link) {
5232 if (!netif_carrier_ok(netdev)) {
5233 bool txb2b = true;
5234
5235 /* Cancel scheduled suspend requests. */
5236 pm_runtime_resume(netdev->dev.parent);
5237
5238 /* Checking if MAC is in DMoff state*/
5239 pcim_state = er32(STATUS);
5240 while (pcim_state & E1000_STATUS_PCIM_STATE) {
5241 if (tries++ == dmoff_exit_timeout) {
5242 e_dbg("Error in exiting dmoff\n");
5243 break;
5244 }
5245 usleep_range(10000, 20000);
5246 pcim_state = er32(STATUS);
5247
5248 /* Checking if MAC exited DMoff state */
5249 if (!(pcim_state & E1000_STATUS_PCIM_STATE))
5250 e1000_phy_hw_reset(&adapter->hw);
5251 }
5252
5253 /* update snapshot of PHY registers on LSC */
5254 e1000_phy_read_status(adapter);
5255 mac->ops.get_link_up_info(&adapter->hw,
5256 &adapter->link_speed,
5257 &adapter->link_duplex);
5258 e1000_print_link_info(adapter);
5259
5260 /* check if SmartSpeed worked */
5261 e1000e_check_downshift(hw);
5262 if (phy->speed_downgraded)
5263 netdev_warn(netdev,
5264 "Link Speed was downgraded by SmartSpeed\n");
5265
5266 /* On supported PHYs, check for duplex mismatch only
5267 * if link has autonegotiated at 10/100 half
5268 */
5269 if ((hw->phy.type == e1000_phy_igp_3 ||
5270 hw->phy.type == e1000_phy_bm) &&
5271 hw->mac.autoneg &&
5272 (adapter->link_speed == SPEED_10 ||
5273 adapter->link_speed == SPEED_100) &&
5274 (adapter->link_duplex == HALF_DUPLEX)) {
5275 u16 autoneg_exp;
5276
5277 e1e_rphy(hw, MII_EXPANSION, &autoneg_exp);
5278
5279 if (!(autoneg_exp & EXPANSION_NWAY))
5280 e_info("Autonegotiated half duplex but link partner cannot autoneg. Try forcing full duplex if link gets many collisions.\n");
5281 }
5282
5283 /* adjust timeout factor according to speed/duplex */
5284 adapter->tx_timeout_factor = 1;
5285 switch (adapter->link_speed) {
5286 case SPEED_10:
5287 txb2b = false;
5288 adapter->tx_timeout_factor = 16;
5289 break;
5290 case SPEED_100:
5291 txb2b = false;
5292 adapter->tx_timeout_factor = 10;
5293 break;
5294 }
5295
5296 /* workaround: re-program speed mode bit after
5297 * link-up event
5298 */
5299 if ((adapter->flags & FLAG_TARC_SPEED_MODE_BIT) &&
5300 !txb2b) {
5301 u32 tarc0;
5302
5303 tarc0 = er32(TARC(0));
5304 tarc0 &= ~SPEED_MODE_BIT;
5305 ew32(TARC(0), tarc0);
5306 }
5307
5308 /* disable TSO for pcie and 10/100 speeds, to avoid
5309 * some hardware issues
5310 */
5311 if (!(adapter->flags & FLAG_TSO_FORCE)) {
5312 switch (adapter->link_speed) {
5313 case SPEED_10:
5314 case SPEED_100:
5315 e_info("10/100 speed: disabling TSO\n");
5316 netdev->features &= ~NETIF_F_TSO;
5317 netdev->features &= ~NETIF_F_TSO6;
5318 break;
5319 case SPEED_1000:
5320 netdev->features |= NETIF_F_TSO;
5321 netdev->features |= NETIF_F_TSO6;
5322 break;
5323 default:
5324 /* oops */
5325 break;
5326 }
5327 if (hw->mac.type == e1000_pch_spt) {
5328 netdev->features &= ~NETIF_F_TSO;
5329 netdev->features &= ~NETIF_F_TSO6;
5330 }
5331 }
5332
5333 /* enable transmits in the hardware, need to do this
5334 * after setting TARC(0)
5335 */
5336 tctl = er32(TCTL);
5337 tctl |= E1000_TCTL_EN;
5338 ew32(TCTL, tctl);
5339
5340 /* Perform any post-link-up configuration before
5341 * reporting link up.
5342 */
5343 if (phy->ops.cfg_on_link_up)
5344 phy->ops.cfg_on_link_up(hw);
5345
5346 netif_wake_queue(netdev);
5347 netif_carrier_on(netdev);
5348
5349 if (!test_bit(__E1000_DOWN, &adapter->state))
5350 mod_timer(&adapter->phy_info_timer,
5351 round_jiffies(jiffies + 2 * HZ));
5352 }
5353 } else {
5354 if (netif_carrier_ok(netdev)) {
5355 adapter->link_speed = 0;
5356 adapter->link_duplex = 0;
5357 /* Link status message must follow this format */
5358 netdev_info(netdev, "NIC Link is Down\n");
5359 netif_carrier_off(netdev);
5360 netif_stop_queue(netdev);
5361 if (!test_bit(__E1000_DOWN, &adapter->state))
5362 mod_timer(&adapter->phy_info_timer,
5363 round_jiffies(jiffies + 2 * HZ));
5364
5365 /* 8000ES2LAN requires a Rx packet buffer work-around
5366 * on link down event; reset the controller to flush
5367 * the Rx packet buffer.
5368 */
5369 if (adapter->flags & FLAG_RX_NEEDS_RESTART)
5370 adapter->flags |= FLAG_RESTART_NOW;
5371 else
5372 pm_schedule_suspend(netdev->dev.parent,
5373 LINK_TIMEOUT);
5374 }
5375 }
5376
5377link_up:
5378 spin_lock(&adapter->stats64_lock);
5379 e1000e_update_stats(adapter);
5380
5381 mac->tx_packet_delta = adapter->stats.tpt - adapter->tpt_old;
5382 adapter->tpt_old = adapter->stats.tpt;
5383 mac->collision_delta = adapter->stats.colc - adapter->colc_old;
5384 adapter->colc_old = adapter->stats.colc;
5385
5386 adapter->gorc = adapter->stats.gorc - adapter->gorc_old;
5387 adapter->gorc_old = adapter->stats.gorc;
5388 adapter->gotc = adapter->stats.gotc - adapter->gotc_old;
5389 adapter->gotc_old = adapter->stats.gotc;
5390 spin_unlock(&adapter->stats64_lock);
5391
5392 /* If the link is lost the controller stops DMA, but
5393 * if there is queued Tx work it cannot be done. So
5394 * reset the controller to flush the Tx packet buffers.
5395 */
5396 if (!netif_carrier_ok(netdev) &&
5397 (e1000_desc_unused(tx_ring) + 1 < tx_ring->count))
5398 adapter->flags |= FLAG_RESTART_NOW;
5399
5400 /* If reset is necessary, do it outside of interrupt context. */
5401 if (adapter->flags & FLAG_RESTART_NOW) {
5402 schedule_work(&adapter->reset_task);
5403 /* return immediately since reset is imminent */
5404 return;
5405 }
5406
5407 e1000e_update_adaptive(&adapter->hw);
5408
5409 /* Simple mode for Interrupt Throttle Rate (ITR) */
5410 if (adapter->itr_setting == 4) {
5411 /* Symmetric Tx/Rx gets a reduced ITR=2000;
5412 * Total asymmetrical Tx or Rx gets ITR=8000;
5413 * everyone else is between 2000-8000.
5414 */
5415 u32 goc = (adapter->gotc + adapter->gorc) / 10000;
5416 u32 dif = (adapter->gotc > adapter->gorc ?
5417 adapter->gotc - adapter->gorc :
5418 adapter->gorc - adapter->gotc) / 10000;
5419 u32 itr = goc > 0 ? (dif * 6000 / goc + 2000) : 8000;
5420
5421 e1000e_write_itr(adapter, itr);
5422 }
5423
5424 /* Cause software interrupt to ensure Rx ring is cleaned */
5425 if (adapter->msix_entries)
5426 ew32(ICS, adapter->rx_ring->ims_val);
5427 else
5428 ew32(ICS, E1000_ICS_RXDMT0);
5429
5430 /* flush pending descriptors to memory before detecting Tx hang */
5431 e1000e_flush_descriptors(adapter);
5432
5433 /* Force detection of hung controller every watchdog period */
5434 adapter->detect_tx_hung = true;
5435
5436 /* With 82571 controllers, LAA may be overwritten due to controller
5437 * reset from the other port. Set the appropriate LAA in RAR[0]
5438 */
5439 if (e1000e_get_laa_state_82571(hw))
5440 hw->mac.ops.rar_set(hw, adapter->hw.mac.addr, 0);
5441
5442 if (adapter->flags2 & FLAG2_CHECK_PHY_HANG)
5443 e1000e_check_82574_phy_workaround(adapter);
5444
5445 /* Clear valid timestamp stuck in RXSTMPL/H due to a Rx error */
5446 if (adapter->hwtstamp_config.rx_filter != HWTSTAMP_FILTER_NONE) {
5447 if ((adapter->flags2 & FLAG2_CHECK_RX_HWTSTAMP) &&
5448 (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_VALID)) {
5449 er32(RXSTMPH);
5450 adapter->rx_hwtstamp_cleared++;
5451 } else {
5452 adapter->flags2 |= FLAG2_CHECK_RX_HWTSTAMP;
5453 }
5454 }
5455
5456 /* Reset the timer */
5457 if (!test_bit(__E1000_DOWN, &adapter->state))
5458 mod_timer(&adapter->watchdog_timer,
5459 round_jiffies(jiffies + 2 * HZ));
5460}
5461
5462#define E1000_TX_FLAGS_CSUM 0x00000001
5463#define E1000_TX_FLAGS_VLAN 0x00000002
5464#define E1000_TX_FLAGS_TSO 0x00000004
5465#define E1000_TX_FLAGS_IPV4 0x00000008
5466#define E1000_TX_FLAGS_NO_FCS 0x00000010
5467#define E1000_TX_FLAGS_HWTSTAMP 0x00000020
5468#define E1000_TX_FLAGS_VLAN_MASK 0xffff0000
5469#define E1000_TX_FLAGS_VLAN_SHIFT 16
5470
5471static int e1000_tso(struct e1000_ring *tx_ring, struct sk_buff *skb,
5472 __be16 protocol)
5473{
5474 struct e1000_context_desc *context_desc;
5475 struct e1000_buffer *buffer_info;
5476 unsigned int i;
5477 u32 cmd_length = 0;
5478 u16 ipcse = 0, mss;
5479 u8 ipcss, ipcso, tucss, tucso, hdr_len;
5480 int err;
5481
5482 if (!skb_is_gso(skb))
5483 return 0;
5484
5485 err = skb_cow_head(skb, 0);
5486 if (err < 0)
5487 return err;
5488
5489 hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
5490 mss = skb_shinfo(skb)->gso_size;
5491 if (protocol == htons(ETH_P_IP)) {
5492 struct iphdr *iph = ip_hdr(skb);
5493 iph->tot_len = 0;
5494 iph->check = 0;
5495 tcp_hdr(skb)->check = ~csum_tcpudp_magic(iph->saddr, iph->daddr,
5496 0, IPPROTO_TCP, 0);
5497 cmd_length = E1000_TXD_CMD_IP;
5498 ipcse = skb_transport_offset(skb) - 1;
5499 } else if (skb_is_gso_v6(skb)) {
5500 tcp_v6_gso_csum_prep(skb);
5501 ipcse = 0;
5502 }
5503 ipcss = skb_network_offset(skb);
5504 ipcso = (void *)&(ip_hdr(skb)->check) - (void *)skb->data;
5505 tucss = skb_transport_offset(skb);
5506 tucso = (void *)&(tcp_hdr(skb)->check) - (void *)skb->data;
5507
5508 cmd_length |= (E1000_TXD_CMD_DEXT | E1000_TXD_CMD_TSE |
5509 E1000_TXD_CMD_TCP | (skb->len - (hdr_len)));
5510
5511 i = tx_ring->next_to_use;
5512 context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
5513 buffer_info = &tx_ring->buffer_info[i];
5514
5515 context_desc->lower_setup.ip_fields.ipcss = ipcss;
5516 context_desc->lower_setup.ip_fields.ipcso = ipcso;
5517 context_desc->lower_setup.ip_fields.ipcse = cpu_to_le16(ipcse);
5518 context_desc->upper_setup.tcp_fields.tucss = tucss;
5519 context_desc->upper_setup.tcp_fields.tucso = tucso;
5520 context_desc->upper_setup.tcp_fields.tucse = 0;
5521 context_desc->tcp_seg_setup.fields.mss = cpu_to_le16(mss);
5522 context_desc->tcp_seg_setup.fields.hdr_len = hdr_len;
5523 context_desc->cmd_and_length = cpu_to_le32(cmd_length);
5524
5525 buffer_info->time_stamp = jiffies;
5526 buffer_info->next_to_watch = i;
5527
5528 i++;
5529 if (i == tx_ring->count)
5530 i = 0;
5531 tx_ring->next_to_use = i;
5532
5533 return 1;
5534}
5535
5536static bool e1000_tx_csum(struct e1000_ring *tx_ring, struct sk_buff *skb,
5537 __be16 protocol)
5538{
5539 struct e1000_adapter *adapter = tx_ring->adapter;
5540 struct e1000_context_desc *context_desc;
5541 struct e1000_buffer *buffer_info;
5542 unsigned int i;
5543 u8 css;
5544 u32 cmd_len = E1000_TXD_CMD_DEXT;
5545
5546 if (skb->ip_summed != CHECKSUM_PARTIAL)
5547 return false;
5548
5549 switch (protocol) {
5550 case cpu_to_be16(ETH_P_IP):
5551 if (ip_hdr(skb)->protocol == IPPROTO_TCP)
5552 cmd_len |= E1000_TXD_CMD_TCP;
5553 break;
5554 case cpu_to_be16(ETH_P_IPV6):
5555 /* XXX not handling all IPV6 headers */
5556 if (ipv6_hdr(skb)->nexthdr == IPPROTO_TCP)
5557 cmd_len |= E1000_TXD_CMD_TCP;
5558 break;
5559 default:
5560 if (unlikely(net_ratelimit()))
5561 e_warn("checksum_partial proto=%x!\n",
5562 be16_to_cpu(protocol));
5563 break;
5564 }
5565
5566 css = skb_checksum_start_offset(skb);
5567
5568 i = tx_ring->next_to_use;
5569 buffer_info = &tx_ring->buffer_info[i];
5570 context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
5571
5572 context_desc->lower_setup.ip_config = 0;
5573 context_desc->upper_setup.tcp_fields.tucss = css;
5574 context_desc->upper_setup.tcp_fields.tucso = css + skb->csum_offset;
5575 context_desc->upper_setup.tcp_fields.tucse = 0;
5576 context_desc->tcp_seg_setup.data = 0;
5577 context_desc->cmd_and_length = cpu_to_le32(cmd_len);
5578
5579 buffer_info->time_stamp = jiffies;
5580 buffer_info->next_to_watch = i;
5581
5582 i++;
5583 if (i == tx_ring->count)
5584 i = 0;
5585 tx_ring->next_to_use = i;
5586
5587 return true;
5588}
5589
5590static int e1000_tx_map(struct e1000_ring *tx_ring, struct sk_buff *skb,
5591 unsigned int first, unsigned int max_per_txd,
5592 unsigned int nr_frags)
5593{
5594 struct e1000_adapter *adapter = tx_ring->adapter;
5595 struct pci_dev *pdev = adapter->pdev;
5596 struct e1000_buffer *buffer_info;
5597 unsigned int len = skb_headlen(skb);
5598 unsigned int offset = 0, size, count = 0, i;
5599 unsigned int f, bytecount, segs;
5600
5601 i = tx_ring->next_to_use;
5602
5603 while (len) {
5604 buffer_info = &tx_ring->buffer_info[i];
5605 size = min(len, max_per_txd);
5606
5607 buffer_info->length = size;
5608 buffer_info->time_stamp = jiffies;
5609 buffer_info->next_to_watch = i;
5610 buffer_info->dma = dma_map_single(&pdev->dev,
5611 skb->data + offset,
5612 size, DMA_TO_DEVICE);
5613 buffer_info->mapped_as_page = false;
5614 if (dma_mapping_error(&pdev->dev, buffer_info->dma))
5615 goto dma_error;
5616
5617 len -= size;
5618 offset += size;
5619 count++;
5620
5621 if (len) {
5622 i++;
5623 if (i == tx_ring->count)
5624 i = 0;
5625 }
5626 }
5627
5628 for (f = 0; f < nr_frags; f++) {
5629 const skb_frag_t *frag = &skb_shinfo(skb)->frags[f];
5630
5631 len = skb_frag_size(frag);
5632 offset = 0;
5633
5634 while (len) {
5635 i++;
5636 if (i == tx_ring->count)
5637 i = 0;
5638
5639 buffer_info = &tx_ring->buffer_info[i];
5640 size = min(len, max_per_txd);
5641
5642 buffer_info->length = size;
5643 buffer_info->time_stamp = jiffies;
5644 buffer_info->next_to_watch = i;
5645 buffer_info->dma = skb_frag_dma_map(&pdev->dev, frag,
5646 offset, size,
5647 DMA_TO_DEVICE);
5648 buffer_info->mapped_as_page = true;
5649 if (dma_mapping_error(&pdev->dev, buffer_info->dma))
5650 goto dma_error;
5651
5652 len -= size;
5653 offset += size;
5654 count++;
5655 }
5656 }
5657
5658 segs = skb_shinfo(skb)->gso_segs ? : 1;
5659 /* multiply data chunks by size of headers */
5660 bytecount = ((segs - 1) * skb_headlen(skb)) + skb->len;
5661
5662 tx_ring->buffer_info[i].skb = skb;
5663 tx_ring->buffer_info[i].segs = segs;
5664 tx_ring->buffer_info[i].bytecount = bytecount;
5665 tx_ring->buffer_info[first].next_to_watch = i;
5666
5667 return count;
5668
5669dma_error:
5670 dev_err(&pdev->dev, "Tx DMA map failed\n");
5671 buffer_info->dma = 0;
5672 if (count)
5673 count--;
5674
5675 while (count--) {
5676 if (i == 0)
5677 i += tx_ring->count;
5678 i--;
5679 buffer_info = &tx_ring->buffer_info[i];
5680 e1000_put_txbuf(tx_ring, buffer_info, true);
5681 }
5682
5683 return 0;
5684}
5685
5686static void e1000_tx_queue(struct e1000_ring *tx_ring, int tx_flags, int count)
5687{
5688 struct e1000_adapter *adapter = tx_ring->adapter;
5689 struct e1000_tx_desc *tx_desc = NULL;
5690 struct e1000_buffer *buffer_info;
5691 u32 txd_upper = 0, txd_lower = E1000_TXD_CMD_IFCS;
5692 unsigned int i;
5693
5694 if (tx_flags & E1000_TX_FLAGS_TSO) {
5695 txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D |
5696 E1000_TXD_CMD_TSE;
5697 txd_upper |= E1000_TXD_POPTS_TXSM << 8;
5698
5699 if (tx_flags & E1000_TX_FLAGS_IPV4)
5700 txd_upper |= E1000_TXD_POPTS_IXSM << 8;
5701 }
5702
5703 if (tx_flags & E1000_TX_FLAGS_CSUM) {
5704 txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D;
5705 txd_upper |= E1000_TXD_POPTS_TXSM << 8;
5706 }
5707
5708 if (tx_flags & E1000_TX_FLAGS_VLAN) {
5709 txd_lower |= E1000_TXD_CMD_VLE;
5710 txd_upper |= (tx_flags & E1000_TX_FLAGS_VLAN_MASK);
5711 }
5712
5713 if (unlikely(tx_flags & E1000_TX_FLAGS_NO_FCS))
5714 txd_lower &= ~(E1000_TXD_CMD_IFCS);
5715
5716 if (unlikely(tx_flags & E1000_TX_FLAGS_HWTSTAMP)) {
5717 txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D;
5718 txd_upper |= E1000_TXD_EXTCMD_TSTAMP;
5719 }
5720
5721 i = tx_ring->next_to_use;
5722
5723 do {
5724 buffer_info = &tx_ring->buffer_info[i];
5725 tx_desc = E1000_TX_DESC(*tx_ring, i);
5726 tx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
5727 tx_desc->lower.data = cpu_to_le32(txd_lower |
5728 buffer_info->length);
5729 tx_desc->upper.data = cpu_to_le32(txd_upper);
5730
5731 i++;
5732 if (i == tx_ring->count)
5733 i = 0;
5734 } while (--count > 0);
5735
5736 tx_desc->lower.data |= cpu_to_le32(adapter->txd_cmd);
5737
5738 /* txd_cmd re-enables FCS, so we'll re-disable it here as desired. */
5739 if (unlikely(tx_flags & E1000_TX_FLAGS_NO_FCS))
5740 tx_desc->lower.data &= ~(cpu_to_le32(E1000_TXD_CMD_IFCS));
5741
5742 /* Force memory writes to complete before letting h/w
5743 * know there are new descriptors to fetch. (Only
5744 * applicable for weak-ordered memory model archs,
5745 * such as IA-64).
5746 */
5747 wmb();
5748
5749 tx_ring->next_to_use = i;
5750}
5751
5752#define MINIMUM_DHCP_PACKET_SIZE 282
5753static int e1000_transfer_dhcp_info(struct e1000_adapter *adapter,
5754 struct sk_buff *skb)
5755{
5756 struct e1000_hw *hw = &adapter->hw;
5757 u16 length, offset;
5758
5759 if (skb_vlan_tag_present(skb) &&
5760 !((skb_vlan_tag_get(skb) == adapter->hw.mng_cookie.vlan_id) &&
5761 (adapter->hw.mng_cookie.status &
5762 E1000_MNG_DHCP_COOKIE_STATUS_VLAN)))
5763 return 0;
5764
5765 if (skb->len <= MINIMUM_DHCP_PACKET_SIZE)
5766 return 0;
5767
5768 if (((struct ethhdr *)skb->data)->h_proto != htons(ETH_P_IP))
5769 return 0;
5770
5771 {
5772 const struct iphdr *ip = (struct iphdr *)((u8 *)skb->data + 14);
5773 struct udphdr *udp;
5774
5775 if (ip->protocol != IPPROTO_UDP)
5776 return 0;
5777
5778 udp = (struct udphdr *)((u8 *)ip + (ip->ihl << 2));
5779 if (ntohs(udp->dest) != 67)
5780 return 0;
5781
5782 offset = (u8 *)udp + 8 - skb->data;
5783 length = skb->len - offset;
5784 return e1000e_mng_write_dhcp_info(hw, (u8 *)udp + 8, length);
5785 }
5786
5787 return 0;
5788}
5789
5790static int __e1000_maybe_stop_tx(struct e1000_ring *tx_ring, int size)
5791{
5792 struct e1000_adapter *adapter = tx_ring->adapter;
5793
5794 netif_stop_queue(adapter->netdev);
5795 /* Herbert's original patch had:
5796 * smp_mb__after_netif_stop_queue();
5797 * but since that doesn't exist yet, just open code it.
5798 */
5799 smp_mb();
5800
5801 /* We need to check again in a case another CPU has just
5802 * made room available.
5803 */
5804 if (e1000_desc_unused(tx_ring) < size)
5805 return -EBUSY;
5806
5807 /* A reprieve! */
5808 netif_start_queue(adapter->netdev);
5809 ++adapter->restart_queue;
5810 return 0;
5811}
5812
5813static int e1000_maybe_stop_tx(struct e1000_ring *tx_ring, int size)
5814{
5815 BUG_ON(size > tx_ring->count);
5816
5817 if (e1000_desc_unused(tx_ring) >= size)
5818 return 0;
5819 return __e1000_maybe_stop_tx(tx_ring, size);
5820}
5821
5822static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
5823 struct net_device *netdev)
5824{
5825 struct e1000_adapter *adapter = netdev_priv(netdev);
5826 struct e1000_ring *tx_ring = adapter->tx_ring;
5827 unsigned int first;
5828 unsigned int tx_flags = 0;
5829 unsigned int len = skb_headlen(skb);
5830 unsigned int nr_frags;
5831 unsigned int mss;
5832 int count = 0;
5833 int tso;
5834 unsigned int f;
5835 __be16 protocol = vlan_get_protocol(skb);
5836
5837 if (test_bit(__E1000_DOWN, &adapter->state)) {
5838 dev_kfree_skb_any(skb);
5839 return NETDEV_TX_OK;
5840 }
5841
5842 if (skb->len <= 0) {
5843 dev_kfree_skb_any(skb);
5844 return NETDEV_TX_OK;
5845 }
5846
5847 /* The minimum packet size with TCTL.PSP set is 17 bytes so
5848 * pad skb in order to meet this minimum size requirement
5849 */
5850 if (skb_put_padto(skb, 17))
5851 return NETDEV_TX_OK;
5852
5853 mss = skb_shinfo(skb)->gso_size;
5854 if (mss) {
5855 u8 hdr_len;
5856
5857 /* TSO Workaround for 82571/2/3 Controllers -- if skb->data
5858 * points to just header, pull a few bytes of payload from
5859 * frags into skb->data
5860 */
5861 hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
5862 /* we do this workaround for ES2LAN, but it is un-necessary,
5863 * avoiding it could save a lot of cycles
5864 */
5865 if (skb->data_len && (hdr_len == len)) {
5866 unsigned int pull_size;
5867
5868 pull_size = min_t(unsigned int, 4, skb->data_len);
5869 if (!__pskb_pull_tail(skb, pull_size)) {
5870 e_err("__pskb_pull_tail failed.\n");
5871 dev_kfree_skb_any(skb);
5872 return NETDEV_TX_OK;
5873 }
5874 len = skb_headlen(skb);
5875 }
5876 }
5877
5878 /* reserve a descriptor for the offload context */
5879 if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL))
5880 count++;
5881 count++;
5882
5883 count += DIV_ROUND_UP(len, adapter->tx_fifo_limit);
5884
5885 nr_frags = skb_shinfo(skb)->nr_frags;
5886 for (f = 0; f < nr_frags; f++)
5887 count += DIV_ROUND_UP(skb_frag_size(&skb_shinfo(skb)->frags[f]),
5888 adapter->tx_fifo_limit);
5889
5890 if (adapter->hw.mac.tx_pkt_filtering)
5891 e1000_transfer_dhcp_info(adapter, skb);
5892
5893 /* need: count + 2 desc gap to keep tail from touching
5894 * head, otherwise try next time
5895 */
5896 if (e1000_maybe_stop_tx(tx_ring, count + 2))
5897 return NETDEV_TX_BUSY;
5898
5899 if (skb_vlan_tag_present(skb)) {
5900 tx_flags |= E1000_TX_FLAGS_VLAN;
5901 tx_flags |= (skb_vlan_tag_get(skb) <<
5902 E1000_TX_FLAGS_VLAN_SHIFT);
5903 }
5904
5905 first = tx_ring->next_to_use;
5906
5907 tso = e1000_tso(tx_ring, skb, protocol);
5908 if (tso < 0) {
5909 dev_kfree_skb_any(skb);
5910 return NETDEV_TX_OK;
5911 }
5912
5913 if (tso)
5914 tx_flags |= E1000_TX_FLAGS_TSO;
5915 else if (e1000_tx_csum(tx_ring, skb, protocol))
5916 tx_flags |= E1000_TX_FLAGS_CSUM;
5917
5918 /* Old method was to assume IPv4 packet by default if TSO was enabled.
5919 * 82571 hardware supports TSO capabilities for IPv6 as well...
5920 * no longer assume, we must.
5921 */
5922 if (protocol == htons(ETH_P_IP))
5923 tx_flags |= E1000_TX_FLAGS_IPV4;
5924
5925 if (unlikely(skb->no_fcs))
5926 tx_flags |= E1000_TX_FLAGS_NO_FCS;
5927
5928 /* if count is 0 then mapping error has occurred */
5929 count = e1000_tx_map(tx_ring, skb, first, adapter->tx_fifo_limit,
5930 nr_frags);
5931 if (count) {
5932 if (unlikely(skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP) &&
5933 (adapter->flags & FLAG_HAS_HW_TIMESTAMP)) {
5934 if (!adapter->tx_hwtstamp_skb) {
5935 skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS;
5936 tx_flags |= E1000_TX_FLAGS_HWTSTAMP;
5937 adapter->tx_hwtstamp_skb = skb_get(skb);
5938 adapter->tx_hwtstamp_start = jiffies;
5939 schedule_work(&adapter->tx_hwtstamp_work);
5940 } else {
5941 adapter->tx_hwtstamp_skipped++;
5942 }
5943 }
5944
5945 skb_tx_timestamp(skb);
5946
5947 netdev_sent_queue(netdev, skb->len);
5948 e1000_tx_queue(tx_ring, tx_flags, count);
5949 /* Make sure there is space in the ring for the next send. */
5950 e1000_maybe_stop_tx(tx_ring,
5951 (MAX_SKB_FRAGS *
5952 DIV_ROUND_UP(PAGE_SIZE,
5953 adapter->tx_fifo_limit) + 2));
5954
5955 if (!netdev_xmit_more() ||
5956 netif_xmit_stopped(netdev_get_tx_queue(netdev, 0))) {
5957 if (adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA)
5958 e1000e_update_tdt_wa(tx_ring,
5959 tx_ring->next_to_use);
5960 else
5961 writel(tx_ring->next_to_use, tx_ring->tail);
5962 }
5963 } else {
5964 dev_kfree_skb_any(skb);
5965 tx_ring->buffer_info[first].time_stamp = 0;
5966 tx_ring->next_to_use = first;
5967 }
5968
5969 return NETDEV_TX_OK;
5970}
5971
5972/**
5973 * e1000_tx_timeout - Respond to a Tx Hang
5974 * @netdev: network interface device structure
5975 **/
5976static void e1000_tx_timeout(struct net_device *netdev, unsigned int txqueue)
5977{
5978 struct e1000_adapter *adapter = netdev_priv(netdev);
5979
5980 /* Do the reset outside of interrupt context */
5981 adapter->tx_timeout_count++;
5982 schedule_work(&adapter->reset_task);
5983}
5984
5985static void e1000_reset_task(struct work_struct *work)
5986{
5987 struct e1000_adapter *adapter;
5988 adapter = container_of(work, struct e1000_adapter, reset_task);
5989
5990 /* don't run the task if already down */
5991 if (test_bit(__E1000_DOWN, &adapter->state))
5992 return;
5993
5994 if (!(adapter->flags & FLAG_RESTART_NOW)) {
5995 e1000e_dump(adapter);
5996 e_err("Reset adapter unexpectedly\n");
5997 }
5998 e1000e_reinit_locked(adapter);
5999}
6000
6001/**
6002 * e1000_get_stats64 - Get System Network Statistics
6003 * @netdev: network interface device structure
6004 * @stats: rtnl_link_stats64 pointer
6005 *
6006 * Returns the address of the device statistics structure.
6007 **/
6008void e1000e_get_stats64(struct net_device *netdev,
6009 struct rtnl_link_stats64 *stats)
6010{
6011 struct e1000_adapter *adapter = netdev_priv(netdev);
6012
6013 spin_lock(&adapter->stats64_lock);
6014 e1000e_update_stats(adapter);
6015 /* Fill out the OS statistics structure */
6016 stats->rx_bytes = adapter->stats.gorc;
6017 stats->rx_packets = adapter->stats.gprc;
6018 stats->tx_bytes = adapter->stats.gotc;
6019 stats->tx_packets = adapter->stats.gptc;
6020 stats->multicast = adapter->stats.mprc;
6021 stats->collisions = adapter->stats.colc;
6022
6023 /* Rx Errors */
6024
6025 /* RLEC on some newer hardware can be incorrect so build
6026 * our own version based on RUC and ROC
6027 */
6028 stats->rx_errors = adapter->stats.rxerrc +
6029 adapter->stats.crcerrs + adapter->stats.algnerrc +
6030 adapter->stats.ruc + adapter->stats.roc + adapter->stats.cexterr;
6031 stats->rx_length_errors = adapter->stats.ruc + adapter->stats.roc;
6032 stats->rx_crc_errors = adapter->stats.crcerrs;
6033 stats->rx_frame_errors = adapter->stats.algnerrc;
6034 stats->rx_missed_errors = adapter->stats.mpc;
6035
6036 /* Tx Errors */
6037 stats->tx_errors = adapter->stats.ecol + adapter->stats.latecol;
6038 stats->tx_aborted_errors = adapter->stats.ecol;
6039 stats->tx_window_errors = adapter->stats.latecol;
6040 stats->tx_carrier_errors = adapter->stats.tncrs;
6041
6042 /* Tx Dropped needs to be maintained elsewhere */
6043
6044 spin_unlock(&adapter->stats64_lock);
6045}
6046
6047/**
6048 * e1000_change_mtu - Change the Maximum Transfer Unit
6049 * @netdev: network interface device structure
6050 * @new_mtu: new value for maximum frame size
6051 *
6052 * Returns 0 on success, negative on failure
6053 **/
6054static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
6055{
6056 struct e1000_adapter *adapter = netdev_priv(netdev);
6057 int max_frame = new_mtu + VLAN_ETH_HLEN + ETH_FCS_LEN;
6058
6059 /* Jumbo frame support */
6060 if ((new_mtu > ETH_DATA_LEN) &&
6061 !(adapter->flags & FLAG_HAS_JUMBO_FRAMES)) {
6062 e_err("Jumbo Frames not supported.\n");
6063 return -EINVAL;
6064 }
6065
6066 /* Jumbo frame workaround on 82579 and newer requires CRC be stripped */
6067 if ((adapter->hw.mac.type >= e1000_pch2lan) &&
6068 !(adapter->flags2 & FLAG2_CRC_STRIPPING) &&
6069 (new_mtu > ETH_DATA_LEN)) {
6070 e_err("Jumbo Frames not supported on this device when CRC stripping is disabled.\n");
6071 return -EINVAL;
6072 }
6073
6074 while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
6075 usleep_range(1000, 1100);
6076 /* e1000e_down -> e1000e_reset dependent on max_frame_size & mtu */
6077 adapter->max_frame_size = max_frame;
6078 netdev_dbg(netdev, "changing MTU from %d to %d\n",
6079 netdev->mtu, new_mtu);
6080 netdev->mtu = new_mtu;
6081
6082 pm_runtime_get_sync(netdev->dev.parent);
6083
6084 if (netif_running(netdev))
6085 e1000e_down(adapter, true);
6086
6087 /* NOTE: netdev_alloc_skb reserves 16 bytes, and typically NET_IP_ALIGN
6088 * means we reserve 2 more, this pushes us to allocate from the next
6089 * larger slab size.
6090 * i.e. RXBUFFER_2048 --> size-4096 slab
6091 * However with the new *_jumbo_rx* routines, jumbo receives will use
6092 * fragmented skbs
6093 */
6094
6095 if (max_frame <= 2048)
6096 adapter->rx_buffer_len = 2048;
6097 else
6098 adapter->rx_buffer_len = 4096;
6099
6100 /* adjust allocation if LPE protects us, and we aren't using SBP */
6101 if (max_frame <= (VLAN_ETH_FRAME_LEN + ETH_FCS_LEN))
6102 adapter->rx_buffer_len = VLAN_ETH_FRAME_LEN + ETH_FCS_LEN;
6103
6104 if (netif_running(netdev))
6105 e1000e_up(adapter);
6106 else
6107 e1000e_reset(adapter);
6108
6109 pm_runtime_put_sync(netdev->dev.parent);
6110
6111 clear_bit(__E1000_RESETTING, &adapter->state);
6112
6113 return 0;
6114}
6115
6116static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
6117 int cmd)
6118{
6119 struct e1000_adapter *adapter = netdev_priv(netdev);
6120 struct mii_ioctl_data *data = if_mii(ifr);
6121
6122 if (adapter->hw.phy.media_type != e1000_media_type_copper)
6123 return -EOPNOTSUPP;
6124
6125 switch (cmd) {
6126 case SIOCGMIIPHY:
6127 data->phy_id = adapter->hw.phy.addr;
6128 break;
6129 case SIOCGMIIREG:
6130 e1000_phy_read_status(adapter);
6131
6132 switch (data->reg_num & 0x1F) {
6133 case MII_BMCR:
6134 data->val_out = adapter->phy_regs.bmcr;
6135 break;
6136 case MII_BMSR:
6137 data->val_out = adapter->phy_regs.bmsr;
6138 break;
6139 case MII_PHYSID1:
6140 data->val_out = (adapter->hw.phy.id >> 16);
6141 break;
6142 case MII_PHYSID2:
6143 data->val_out = (adapter->hw.phy.id & 0xFFFF);
6144 break;
6145 case MII_ADVERTISE:
6146 data->val_out = adapter->phy_regs.advertise;
6147 break;
6148 case MII_LPA:
6149 data->val_out = adapter->phy_regs.lpa;
6150 break;
6151 case MII_EXPANSION:
6152 data->val_out = adapter->phy_regs.expansion;
6153 break;
6154 case MII_CTRL1000:
6155 data->val_out = adapter->phy_regs.ctrl1000;
6156 break;
6157 case MII_STAT1000:
6158 data->val_out = adapter->phy_regs.stat1000;
6159 break;
6160 case MII_ESTATUS:
6161 data->val_out = adapter->phy_regs.estatus;
6162 break;
6163 default:
6164 return -EIO;
6165 }
6166 break;
6167 case SIOCSMIIREG:
6168 default:
6169 return -EOPNOTSUPP;
6170 }
6171 return 0;
6172}
6173
6174/**
6175 * e1000e_hwtstamp_ioctl - control hardware time stamping
6176 * @netdev: network interface device structure
6177 * @ifreq: interface request
6178 *
6179 * Outgoing time stamping can be enabled and disabled. Play nice and
6180 * disable it when requested, although it shouldn't cause any overhead
6181 * when no packet needs it. At most one packet in the queue may be
6182 * marked for time stamping, otherwise it would be impossible to tell
6183 * for sure to which packet the hardware time stamp belongs.
6184 *
6185 * Incoming time stamping has to be configured via the hardware filters.
6186 * Not all combinations are supported, in particular event type has to be
6187 * specified. Matching the kind of event packet is not supported, with the
6188 * exception of "all V2 events regardless of level 2 or 4".
6189 **/
6190static int e1000e_hwtstamp_set(struct net_device *netdev, struct ifreq *ifr)
6191{
6192 struct e1000_adapter *adapter = netdev_priv(netdev);
6193 struct hwtstamp_config config;
6194 int ret_val;
6195
6196 if (copy_from_user(&config, ifr->ifr_data, sizeof(config)))
6197 return -EFAULT;
6198
6199 ret_val = e1000e_config_hwtstamp(adapter, &config);
6200 if (ret_val)
6201 return ret_val;
6202
6203 switch (config.rx_filter) {
6204 case HWTSTAMP_FILTER_PTP_V2_L4_SYNC:
6205 case HWTSTAMP_FILTER_PTP_V2_L2_SYNC:
6206 case HWTSTAMP_FILTER_PTP_V2_SYNC:
6207 case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ:
6208 case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ:
6209 case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ:
6210 /* With V2 type filters which specify a Sync or Delay Request,
6211 * Path Delay Request/Response messages are also time stamped
6212 * by hardware so notify the caller the requested packets plus
6213 * some others are time stamped.
6214 */
6215 config.rx_filter = HWTSTAMP_FILTER_SOME;
6216 break;
6217 default:
6218 break;
6219 }
6220
6221 return copy_to_user(ifr->ifr_data, &config,
6222 sizeof(config)) ? -EFAULT : 0;
6223}
6224
6225static int e1000e_hwtstamp_get(struct net_device *netdev, struct ifreq *ifr)
6226{
6227 struct e1000_adapter *adapter = netdev_priv(netdev);
6228
6229 return copy_to_user(ifr->ifr_data, &adapter->hwtstamp_config,
6230 sizeof(adapter->hwtstamp_config)) ? -EFAULT : 0;
6231}
6232
6233static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
6234{
6235 switch (cmd) {
6236 case SIOCGMIIPHY:
6237 case SIOCGMIIREG:
6238 case SIOCSMIIREG:
6239 return e1000_mii_ioctl(netdev, ifr, cmd);
6240 case SIOCSHWTSTAMP:
6241 return e1000e_hwtstamp_set(netdev, ifr);
6242 case SIOCGHWTSTAMP:
6243 return e1000e_hwtstamp_get(netdev, ifr);
6244 default:
6245 return -EOPNOTSUPP;
6246 }
6247}
6248
6249static int e1000_init_phy_wakeup(struct e1000_adapter *adapter, u32 wufc)
6250{
6251 struct e1000_hw *hw = &adapter->hw;
6252 u32 i, mac_reg, wuc;
6253 u16 phy_reg, wuc_enable;
6254 int retval;
6255
6256 /* copy MAC RARs to PHY RARs */
6257 e1000_copy_rx_addrs_to_phy_ich8lan(hw);
6258
6259 retval = hw->phy.ops.acquire(hw);
6260 if (retval) {
6261 e_err("Could not acquire PHY\n");
6262 return retval;
6263 }
6264
6265 /* Enable access to wakeup registers on and set page to BM_WUC_PAGE */
6266 retval = e1000_enable_phy_wakeup_reg_access_bm(hw, &wuc_enable);
6267 if (retval)
6268 goto release;
6269
6270 /* copy MAC MTA to PHY MTA - only needed for pchlan */
6271 for (i = 0; i < adapter->hw.mac.mta_reg_count; i++) {
6272 mac_reg = E1000_READ_REG_ARRAY(hw, E1000_MTA, i);
6273 hw->phy.ops.write_reg_page(hw, BM_MTA(i),
6274 (u16)(mac_reg & 0xFFFF));
6275 hw->phy.ops.write_reg_page(hw, BM_MTA(i) + 1,
6276 (u16)((mac_reg >> 16) & 0xFFFF));
6277 }
6278
6279 /* configure PHY Rx Control register */
6280 hw->phy.ops.read_reg_page(&adapter->hw, BM_RCTL, &phy_reg);
6281 mac_reg = er32(RCTL);
6282 if (mac_reg & E1000_RCTL_UPE)
6283 phy_reg |= BM_RCTL_UPE;
6284 if (mac_reg & E1000_RCTL_MPE)
6285 phy_reg |= BM_RCTL_MPE;
6286 phy_reg &= ~(BM_RCTL_MO_MASK);
6287 if (mac_reg & E1000_RCTL_MO_3)
6288 phy_reg |= (((mac_reg & E1000_RCTL_MO_3) >> E1000_RCTL_MO_SHIFT)
6289 << BM_RCTL_MO_SHIFT);
6290 if (mac_reg & E1000_RCTL_BAM)
6291 phy_reg |= BM_RCTL_BAM;
6292 if (mac_reg & E1000_RCTL_PMCF)
6293 phy_reg |= BM_RCTL_PMCF;
6294 mac_reg = er32(CTRL);
6295 if (mac_reg & E1000_CTRL_RFCE)
6296 phy_reg |= BM_RCTL_RFCE;
6297 hw->phy.ops.write_reg_page(&adapter->hw, BM_RCTL, phy_reg);
6298
6299 wuc = E1000_WUC_PME_EN;
6300 if (wufc & (E1000_WUFC_MAG | E1000_WUFC_LNKC))
6301 wuc |= E1000_WUC_APME;
6302
6303 /* enable PHY wakeup in MAC register */
6304 ew32(WUFC, wufc);
6305 ew32(WUC, (E1000_WUC_PHY_WAKE | E1000_WUC_APMPME |
6306 E1000_WUC_PME_STATUS | wuc));
6307
6308 /* configure and enable PHY wakeup in PHY registers */
6309 hw->phy.ops.write_reg_page(&adapter->hw, BM_WUFC, wufc);
6310 hw->phy.ops.write_reg_page(&adapter->hw, BM_WUC, wuc);
6311
6312 /* activate PHY wakeup */
6313 wuc_enable |= BM_WUC_ENABLE_BIT | BM_WUC_HOST_WU_BIT;
6314 retval = e1000_disable_phy_wakeup_reg_access_bm(hw, &wuc_enable);
6315 if (retval)
6316 e_err("Could not set PHY Host Wakeup bit\n");
6317release:
6318 hw->phy.ops.release(hw);
6319
6320 return retval;
6321}
6322
6323static void e1000e_flush_lpic(struct pci_dev *pdev)
6324{
6325 struct net_device *netdev = pci_get_drvdata(pdev);
6326 struct e1000_adapter *adapter = netdev_priv(netdev);
6327 struct e1000_hw *hw = &adapter->hw;
6328 u32 ret_val;
6329
6330 pm_runtime_get_sync(netdev->dev.parent);
6331
6332 ret_val = hw->phy.ops.acquire(hw);
6333 if (ret_val)
6334 goto fl_out;
6335
6336 pr_info("EEE TX LPI TIMER: %08X\n",
6337 er32(LPIC) >> E1000_LPIC_LPIET_SHIFT);
6338
6339 hw->phy.ops.release(hw);
6340
6341fl_out:
6342 pm_runtime_put_sync(netdev->dev.parent);
6343}
6344
6345/* S0ix implementation */
6346static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)
6347{
6348 struct e1000_hw *hw = &adapter->hw;
6349 u32 mac_data;
6350 u16 phy_data;
6351
6352 /* Disable the periodic inband message,
6353 * don't request PCIe clock in K1 page770_17[10:9] = 10b
6354 */
6355 e1e_rphy(hw, HV_PM_CTRL, &phy_data);
6356 phy_data &= ~HV_PM_CTRL_K1_CLK_REQ;
6357 phy_data |= BIT(10);
6358 e1e_wphy(hw, HV_PM_CTRL, phy_data);
6359
6360 /* Make sure we don't exit K1 every time a new packet arrives
6361 * 772_29[5] = 1 CS_Mode_Stay_In_K1
6362 */
6363 e1e_rphy(hw, I217_CGFREG, &phy_data);
6364 phy_data |= BIT(5);
6365 e1e_wphy(hw, I217_CGFREG, phy_data);
6366
6367 /* Change the MAC/PHY interface to SMBus
6368 * Force the SMBus in PHY page769_23[0] = 1
6369 * Force the SMBus in MAC CTRL_EXT[11] = 1
6370 */
6371 e1e_rphy(hw, CV_SMB_CTRL, &phy_data);
6372 phy_data |= CV_SMB_CTRL_FORCE_SMBUS;
6373 e1e_wphy(hw, CV_SMB_CTRL, phy_data);
6374 mac_data = er32(CTRL_EXT);
6375 mac_data |= E1000_CTRL_EXT_FORCE_SMBUS;
6376 ew32(CTRL_EXT, mac_data);
6377
6378 /* DFT control: PHY bit: page769_20[0] = 1
6379 * Gate PPW via EXTCNF_CTRL - set 0x0F00[7] = 1
6380 */
6381 e1e_rphy(hw, I82579_DFT_CTRL, &phy_data);
6382 phy_data |= BIT(0);
6383 e1e_wphy(hw, I82579_DFT_CTRL, phy_data);
6384
6385 mac_data = er32(EXTCNF_CTRL);
6386 mac_data |= E1000_EXTCNF_CTRL_GATE_PHY_CFG;
6387 ew32(EXTCNF_CTRL, mac_data);
6388
6389 /* Check MAC Tx/Rx packet buffer pointers.
6390 * Reset MAC Tx/Rx packet buffer pointers to suppress any
6391 * pending traffic indication that would prevent power gating.
6392 */
6393 mac_data = er32(TDFH);
6394 if (mac_data)
6395 ew32(TDFH, 0);
6396 mac_data = er32(TDFT);
6397 if (mac_data)
6398 ew32(TDFT, 0);
6399 mac_data = er32(TDFHS);
6400 if (mac_data)
6401 ew32(TDFHS, 0);
6402 mac_data = er32(TDFTS);
6403 if (mac_data)
6404 ew32(TDFTS, 0);
6405 mac_data = er32(TDFPC);
6406 if (mac_data)
6407 ew32(TDFPC, 0);
6408 mac_data = er32(RDFH);
6409 if (mac_data)
6410 ew32(RDFH, 0);
6411 mac_data = er32(RDFT);
6412 if (mac_data)
6413 ew32(RDFT, 0);
6414 mac_data = er32(RDFHS);
6415 if (mac_data)
6416 ew32(RDFHS, 0);
6417 mac_data = er32(RDFTS);
6418 if (mac_data)
6419 ew32(RDFTS, 0);
6420 mac_data = er32(RDFPC);
6421 if (mac_data)
6422 ew32(RDFPC, 0);
6423
6424 /* Enable the Dynamic Power Gating in the MAC */
6425 mac_data = er32(FEXTNVM7);
6426 mac_data |= BIT(22);
6427 ew32(FEXTNVM7, mac_data);
6428
6429 /* Disable the time synchronization clock */
6430 mac_data = er32(FEXTNVM7);
6431 mac_data |= BIT(31);
6432 mac_data &= ~BIT(0);
6433 ew32(FEXTNVM7, mac_data);
6434
6435 /* Dynamic Power Gating Enable */
6436 mac_data = er32(CTRL_EXT);
6437 mac_data |= BIT(3);
6438 ew32(CTRL_EXT, mac_data);
6439
6440 /* Disable disconnected cable conditioning for Power Gating */
6441 mac_data = er32(DPGFR);
6442 mac_data |= BIT(2);
6443 ew32(DPGFR, mac_data);
6444
6445 /* Don't wake from dynamic Power Gating with clock request */
6446 mac_data = er32(FEXTNVM12);
6447 mac_data |= BIT(12);
6448 ew32(FEXTNVM12, mac_data);
6449
6450 /* Ungate PGCB clock */
6451 mac_data = er32(FEXTNVM9);
6452 mac_data |= BIT(28);
6453 ew32(FEXTNVM9, mac_data);
6454
6455 /* Enable K1 off to enable mPHY Power Gating */
6456 mac_data = er32(FEXTNVM6);
6457 mac_data |= BIT(31);
6458 ew32(FEXTNVM12, mac_data);
6459
6460 /* Enable mPHY power gating for any link and speed */
6461 mac_data = er32(FEXTNVM8);
6462 mac_data |= BIT(9);
6463 ew32(FEXTNVM8, mac_data);
6464
6465 /* Enable the Dynamic Clock Gating in the DMA and MAC */
6466 mac_data = er32(CTRL_EXT);
6467 mac_data |= E1000_CTRL_EXT_DMA_DYN_CLK_EN;
6468 ew32(CTRL_EXT, mac_data);
6469
6470 /* No MAC DPG gating SLP_S0 in modern standby
6471 * Switch the logic of the lanphypc to use PMC counter
6472 */
6473 mac_data = er32(FEXTNVM5);
6474 mac_data |= BIT(7);
6475 ew32(FEXTNVM5, mac_data);
6476}
6477
6478static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)
6479{
6480 struct e1000_hw *hw = &adapter->hw;
6481 u32 mac_data;
6482 u16 phy_data;
6483
6484 /* Disable the Dynamic Power Gating in the MAC */
6485 mac_data = er32(FEXTNVM7);
6486 mac_data &= 0xFFBFFFFF;
6487 ew32(FEXTNVM7, mac_data);
6488
6489 /* Enable the time synchronization clock */
6490 mac_data = er32(FEXTNVM7);
6491 mac_data |= BIT(0);
6492 ew32(FEXTNVM7, mac_data);
6493
6494 /* Disable mPHY power gating for any link and speed */
6495 mac_data = er32(FEXTNVM8);
6496 mac_data &= ~BIT(9);
6497 ew32(FEXTNVM8, mac_data);
6498
6499 /* Disable K1 off */
6500 mac_data = er32(FEXTNVM6);
6501 mac_data &= ~BIT(31);
6502 ew32(FEXTNVM12, mac_data);
6503
6504 /* Disable Ungate PGCB clock */
6505 mac_data = er32(FEXTNVM9);
6506 mac_data &= ~BIT(28);
6507 ew32(FEXTNVM9, mac_data);
6508
6509 /* Cancel not waking from dynamic
6510 * Power Gating with clock request
6511 */
6512 mac_data = er32(FEXTNVM12);
6513 mac_data &= ~BIT(12);
6514 ew32(FEXTNVM12, mac_data);
6515
6516 /* Cancel disable disconnected cable conditioning
6517 * for Power Gating
6518 */
6519 mac_data = er32(DPGFR);
6520 mac_data &= ~BIT(2);
6521 ew32(DPGFR, mac_data);
6522
6523 /* Disable Dynamic Power Gating */
6524 mac_data = er32(CTRL_EXT);
6525 mac_data &= 0xFFFFFFF7;
6526 ew32(CTRL_EXT, mac_data);
6527
6528 /* Disable the Dynamic Clock Gating in the DMA and MAC */
6529 mac_data = er32(CTRL_EXT);
6530 mac_data &= 0xFFF7FFFF;
6531 ew32(CTRL_EXT, mac_data);
6532
6533 /* Revert the lanphypc logic to use the internal Gbe counter
6534 * and not the PMC counter
6535 */
6536 mac_data = er32(FEXTNVM5);
6537 mac_data &= 0xFFFFFF7F;
6538 ew32(FEXTNVM5, mac_data);
6539
6540 /* Enable the periodic inband message,
6541 * Request PCIe clock in K1 page770_17[10:9] =01b
6542 */
6543 e1e_rphy(hw, HV_PM_CTRL, &phy_data);
6544 phy_data &= 0xFBFF;
6545 phy_data |= HV_PM_CTRL_K1_CLK_REQ;
6546 e1e_wphy(hw, HV_PM_CTRL, phy_data);
6547
6548 /* Return back configuration
6549 * 772_29[5] = 0 CS_Mode_Stay_In_K1
6550 */
6551 e1e_rphy(hw, I217_CGFREG, &phy_data);
6552 phy_data &= 0xFFDF;
6553 e1e_wphy(hw, I217_CGFREG, phy_data);
6554
6555 /* Change the MAC/PHY interface to Kumeran
6556 * Unforce the SMBus in PHY page769_23[0] = 0
6557 * Unforce the SMBus in MAC CTRL_EXT[11] = 0
6558 */
6559 e1e_rphy(hw, CV_SMB_CTRL, &phy_data);
6560 phy_data &= ~CV_SMB_CTRL_FORCE_SMBUS;
6561 e1e_wphy(hw, CV_SMB_CTRL, phy_data);
6562 mac_data = er32(CTRL_EXT);
6563 mac_data &= ~E1000_CTRL_EXT_FORCE_SMBUS;
6564 ew32(CTRL_EXT, mac_data);
6565}
6566
6567static int e1000e_pm_freeze(struct device *dev)
6568{
6569 struct net_device *netdev = dev_get_drvdata(dev);
6570 struct e1000_adapter *adapter = netdev_priv(netdev);
6571 bool present;
6572
6573 rtnl_lock();
6574
6575 present = netif_device_present(netdev);
6576 netif_device_detach(netdev);
6577
6578 if (present && netif_running(netdev)) {
6579 int count = E1000_CHECK_RESET_COUNT;
6580
6581 while (test_bit(__E1000_RESETTING, &adapter->state) && count--)
6582 usleep_range(10000, 11000);
6583
6584 WARN_ON(test_bit(__E1000_RESETTING, &adapter->state));
6585
6586 /* Quiesce the device without resetting the hardware */
6587 e1000e_down(adapter, false);
6588 e1000_free_irq(adapter);
6589 }
6590 rtnl_unlock();
6591
6592 e1000e_reset_interrupt_capability(adapter);
6593
6594 /* Allow time for pending master requests to run */
6595 e1000e_disable_pcie_master(&adapter->hw);
6596
6597 return 0;
6598}
6599
6600static int __e1000_shutdown(struct pci_dev *pdev, bool runtime)
6601{
6602 struct net_device *netdev = pci_get_drvdata(pdev);
6603 struct e1000_adapter *adapter = netdev_priv(netdev);
6604 struct e1000_hw *hw = &adapter->hw;
6605 u32 ctrl, ctrl_ext, rctl, status, wufc;
6606 int retval = 0;
6607
6608 /* Runtime suspend should only enable wakeup for link changes */
6609 if (runtime)
6610 wufc = E1000_WUFC_LNKC;
6611 else if (device_may_wakeup(&pdev->dev))
6612 wufc = adapter->wol;
6613 else
6614 wufc = 0;
6615
6616 status = er32(STATUS);
6617 if (status & E1000_STATUS_LU)
6618 wufc &= ~E1000_WUFC_LNKC;
6619
6620 if (wufc) {
6621 e1000_setup_rctl(adapter);
6622 e1000e_set_rx_mode(netdev);
6623
6624 /* turn on all-multi mode if wake on multicast is enabled */
6625 if (wufc & E1000_WUFC_MC) {
6626 rctl = er32(RCTL);
6627 rctl |= E1000_RCTL_MPE;
6628 ew32(RCTL, rctl);
6629 }
6630
6631 ctrl = er32(CTRL);
6632 ctrl |= E1000_CTRL_ADVD3WUC;
6633 if (!(adapter->flags2 & FLAG2_HAS_PHY_WAKEUP))
6634 ctrl |= E1000_CTRL_EN_PHY_PWR_MGMT;
6635 ew32(CTRL, ctrl);
6636
6637 if (adapter->hw.phy.media_type == e1000_media_type_fiber ||
6638 adapter->hw.phy.media_type ==
6639 e1000_media_type_internal_serdes) {
6640 /* keep the laser running in D3 */
6641 ctrl_ext = er32(CTRL_EXT);
6642 ctrl_ext |= E1000_CTRL_EXT_SDP3_DATA;
6643 ew32(CTRL_EXT, ctrl_ext);
6644 }
6645
6646 if (!runtime)
6647 e1000e_power_up_phy(adapter);
6648
6649 if (adapter->flags & FLAG_IS_ICH)
6650 e1000_suspend_workarounds_ich8lan(&adapter->hw);
6651
6652 if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) {
6653 /* enable wakeup by the PHY */
6654 retval = e1000_init_phy_wakeup(adapter, wufc);
6655 if (retval)
6656 return retval;
6657 } else {
6658 /* enable wakeup by the MAC */
6659 ew32(WUFC, wufc);
6660 ew32(WUC, E1000_WUC_PME_EN);
6661 }
6662 } else {
6663 ew32(WUC, 0);
6664 ew32(WUFC, 0);
6665
6666 e1000_power_down_phy(adapter);
6667 }
6668
6669 if (adapter->hw.phy.type == e1000_phy_igp_3) {
6670 e1000e_igp3_phy_powerdown_workaround_ich8lan(&adapter->hw);
6671 } else if (hw->mac.type >= e1000_pch_lpt) {
6672 if (wufc && !(wufc & (E1000_WUFC_EX | E1000_WUFC_MC | E1000_WUFC_BC)))
6673 /* ULP does not support wake from unicast, multicast
6674 * or broadcast.
6675 */
6676 retval = e1000_enable_ulp_lpt_lp(hw, !runtime);
6677
6678 if (retval)
6679 return retval;
6680 }
6681
6682 /* Ensure that the appropriate bits are set in LPI_CTRL
6683 * for EEE in Sx
6684 */
6685 if ((hw->phy.type >= e1000_phy_i217) &&
6686 adapter->eee_advert && hw->dev_spec.ich8lan.eee_lp_ability) {
6687 u16 lpi_ctrl = 0;
6688
6689 retval = hw->phy.ops.acquire(hw);
6690 if (!retval) {
6691 retval = e1e_rphy_locked(hw, I82579_LPI_CTRL,
6692 &lpi_ctrl);
6693 if (!retval) {
6694 if (adapter->eee_advert &
6695 hw->dev_spec.ich8lan.eee_lp_ability &
6696 I82579_EEE_100_SUPPORTED)
6697 lpi_ctrl |= I82579_LPI_CTRL_100_ENABLE;
6698 if (adapter->eee_advert &
6699 hw->dev_spec.ich8lan.eee_lp_ability &
6700 I82579_EEE_1000_SUPPORTED)
6701 lpi_ctrl |= I82579_LPI_CTRL_1000_ENABLE;
6702
6703 retval = e1e_wphy_locked(hw, I82579_LPI_CTRL,
6704 lpi_ctrl);
6705 }
6706 }
6707 hw->phy.ops.release(hw);
6708 }
6709
6710 /* Release control of h/w to f/w. If f/w is AMT enabled, this
6711 * would have already happened in close and is redundant.
6712 */
6713 e1000e_release_hw_control(adapter);
6714
6715 pci_clear_master(pdev);
6716
6717 /* The pci-e switch on some quad port adapters will report a
6718 * correctable error when the MAC transitions from D0 to D3. To
6719 * prevent this we need to mask off the correctable errors on the
6720 * downstream port of the pci-e switch.
6721 *
6722 * We don't have the associated upstream bridge while assigning
6723 * the PCI device into guest. For example, the KVM on power is
6724 * one of the cases.
6725 */
6726 if (adapter->flags & FLAG_IS_QUAD_PORT) {
6727 struct pci_dev *us_dev = pdev->bus->self;
6728 u16 devctl;
6729
6730 if (!us_dev)
6731 return 0;
6732
6733 pcie_capability_read_word(us_dev, PCI_EXP_DEVCTL, &devctl);
6734 pcie_capability_write_word(us_dev, PCI_EXP_DEVCTL,
6735 (devctl & ~PCI_EXP_DEVCTL_CERE));
6736
6737 pci_save_state(pdev);
6738 pci_prepare_to_sleep(pdev);
6739
6740 pcie_capability_write_word(us_dev, PCI_EXP_DEVCTL, devctl);
6741 }
6742
6743 return 0;
6744}
6745
6746/**
6747 * __e1000e_disable_aspm - Disable ASPM states
6748 * @pdev: pointer to PCI device struct
6749 * @state: bit-mask of ASPM states to disable
6750 * @locked: indication if this context holds pci_bus_sem locked.
6751 *
6752 * Some devices *must* have certain ASPM states disabled per hardware errata.
6753 **/
6754static void __e1000e_disable_aspm(struct pci_dev *pdev, u16 state, int locked)
6755{
6756 struct pci_dev *parent = pdev->bus->self;
6757 u16 aspm_dis_mask = 0;
6758 u16 pdev_aspmc, parent_aspmc;
6759
6760 switch (state) {
6761 case PCIE_LINK_STATE_L0S:
6762 case PCIE_LINK_STATE_L0S | PCIE_LINK_STATE_L1:
6763 aspm_dis_mask |= PCI_EXP_LNKCTL_ASPM_L0S;
6764 fallthrough; /* can't have L1 without L0s */
6765 case PCIE_LINK_STATE_L1:
6766 aspm_dis_mask |= PCI_EXP_LNKCTL_ASPM_L1;
6767 break;
6768 default:
6769 return;
6770 }
6771
6772 pcie_capability_read_word(pdev, PCI_EXP_LNKCTL, &pdev_aspmc);
6773 pdev_aspmc &= PCI_EXP_LNKCTL_ASPMC;
6774
6775 if (parent) {
6776 pcie_capability_read_word(parent, PCI_EXP_LNKCTL,
6777 &parent_aspmc);
6778 parent_aspmc &= PCI_EXP_LNKCTL_ASPMC;
6779 }
6780
6781 /* Nothing to do if the ASPM states to be disabled already are */
6782 if (!(pdev_aspmc & aspm_dis_mask) &&
6783 (!parent || !(parent_aspmc & aspm_dis_mask)))
6784 return;
6785
6786 dev_info(&pdev->dev, "Disabling ASPM %s %s\n",
6787 (aspm_dis_mask & pdev_aspmc & PCI_EXP_LNKCTL_ASPM_L0S) ?
6788 "L0s" : "",
6789 (aspm_dis_mask & pdev_aspmc & PCI_EXP_LNKCTL_ASPM_L1) ?
6790 "L1" : "");
6791
6792#ifdef CONFIG_PCIEASPM
6793 if (locked)
6794 pci_disable_link_state_locked(pdev, state);
6795 else
6796 pci_disable_link_state(pdev, state);
6797
6798 /* Double-check ASPM control. If not disabled by the above, the
6799 * BIOS is preventing that from happening (or CONFIG_PCIEASPM is
6800 * not enabled); override by writing PCI config space directly.
6801 */
6802 pcie_capability_read_word(pdev, PCI_EXP_LNKCTL, &pdev_aspmc);
6803 pdev_aspmc &= PCI_EXP_LNKCTL_ASPMC;
6804
6805 if (!(aspm_dis_mask & pdev_aspmc))
6806 return;
6807#endif
6808
6809 /* Both device and parent should have the same ASPM setting.
6810 * Disable ASPM in downstream component first and then upstream.
6811 */
6812 pcie_capability_clear_word(pdev, PCI_EXP_LNKCTL, aspm_dis_mask);
6813
6814 if (parent)
6815 pcie_capability_clear_word(parent, PCI_EXP_LNKCTL,
6816 aspm_dis_mask);
6817}
6818
6819/**
6820 * e1000e_disable_aspm - Disable ASPM states.
6821 * @pdev: pointer to PCI device struct
6822 * @state: bit-mask of ASPM states to disable
6823 *
6824 * This function acquires the pci_bus_sem!
6825 * Some devices *must* have certain ASPM states disabled per hardware errata.
6826 **/
6827static void e1000e_disable_aspm(struct pci_dev *pdev, u16 state)
6828{
6829 __e1000e_disable_aspm(pdev, state, 0);
6830}
6831
6832/**
6833 * e1000e_disable_aspm_locked Disable ASPM states.
6834 * @pdev: pointer to PCI device struct
6835 * @state: bit-mask of ASPM states to disable
6836 *
6837 * This function must be called with pci_bus_sem acquired!
6838 * Some devices *must* have certain ASPM states disabled per hardware errata.
6839 **/
6840static void e1000e_disable_aspm_locked(struct pci_dev *pdev, u16 state)
6841{
6842 __e1000e_disable_aspm(pdev, state, 1);
6843}
6844
6845static int e1000e_pm_thaw(struct device *dev)
6846{
6847 struct net_device *netdev = dev_get_drvdata(dev);
6848 struct e1000_adapter *adapter = netdev_priv(netdev);
6849 int rc = 0;
6850
6851 e1000e_set_interrupt_capability(adapter);
6852
6853 rtnl_lock();
6854 if (netif_running(netdev)) {
6855 rc = e1000_request_irq(adapter);
6856 if (rc)
6857 goto err_irq;
6858
6859 e1000e_up(adapter);
6860 }
6861
6862 netif_device_attach(netdev);
6863err_irq:
6864 rtnl_unlock();
6865
6866 return rc;
6867}
6868
6869static int __e1000_resume(struct pci_dev *pdev)
6870{
6871 struct net_device *netdev = pci_get_drvdata(pdev);
6872 struct e1000_adapter *adapter = netdev_priv(netdev);
6873 struct e1000_hw *hw = &adapter->hw;
6874 u16 aspm_disable_flag = 0;
6875
6876 if (adapter->flags2 & FLAG2_DISABLE_ASPM_L0S)
6877 aspm_disable_flag = PCIE_LINK_STATE_L0S;
6878 if (adapter->flags2 & FLAG2_DISABLE_ASPM_L1)
6879 aspm_disable_flag |= PCIE_LINK_STATE_L1;
6880 if (aspm_disable_flag)
6881 e1000e_disable_aspm(pdev, aspm_disable_flag);
6882
6883 pci_set_master(pdev);
6884
6885 if (hw->mac.type >= e1000_pch2lan)
6886 e1000_resume_workarounds_pchlan(&adapter->hw);
6887
6888 e1000e_power_up_phy(adapter);
6889
6890 /* report the system wakeup cause from S3/S4 */
6891 if (adapter->flags2 & FLAG2_HAS_PHY_WAKEUP) {
6892 u16 phy_data;
6893
6894 e1e_rphy(&adapter->hw, BM_WUS, &phy_data);
6895 if (phy_data) {
6896 e_info("PHY Wakeup cause - %s\n",
6897 phy_data & E1000_WUS_EX ? "Unicast Packet" :
6898 phy_data & E1000_WUS_MC ? "Multicast Packet" :
6899 phy_data & E1000_WUS_BC ? "Broadcast Packet" :
6900 phy_data & E1000_WUS_MAG ? "Magic Packet" :
6901 phy_data & E1000_WUS_LNKC ?
6902 "Link Status Change" : "other");
6903 }
6904 e1e_wphy(&adapter->hw, BM_WUS, ~0);
6905 } else {
6906 u32 wus = er32(WUS);
6907
6908 if (wus) {
6909 e_info("MAC Wakeup cause - %s\n",
6910 wus & E1000_WUS_EX ? "Unicast Packet" :
6911 wus & E1000_WUS_MC ? "Multicast Packet" :
6912 wus & E1000_WUS_BC ? "Broadcast Packet" :
6913 wus & E1000_WUS_MAG ? "Magic Packet" :
6914 wus & E1000_WUS_LNKC ? "Link Status Change" :
6915 "other");
6916 }
6917 ew32(WUS, ~0);
6918 }
6919
6920 e1000e_reset(adapter);
6921
6922 e1000_init_manageability_pt(adapter);
6923
6924 /* If the controller has AMT, do not set DRV_LOAD until the interface
6925 * is up. For all other cases, let the f/w know that the h/w is now
6926 * under the control of the driver.
6927 */
6928 if (!(adapter->flags & FLAG_HAS_AMT))
6929 e1000e_get_hw_control(adapter);
6930
6931 return 0;
6932}
6933
6934static __maybe_unused int e1000e_pm_suspend(struct device *dev)
6935{
6936 struct net_device *netdev = pci_get_drvdata(to_pci_dev(dev));
6937 struct e1000_adapter *adapter = netdev_priv(netdev);
6938 struct pci_dev *pdev = to_pci_dev(dev);
6939 struct e1000_hw *hw = &adapter->hw;
6940 int rc;
6941
6942 e1000e_flush_lpic(pdev);
6943
6944 e1000e_pm_freeze(dev);
6945
6946 rc = __e1000_shutdown(pdev, false);
6947 if (rc)
6948 e1000e_pm_thaw(dev);
6949
6950 /* Introduce S0ix implementation */
6951 if (hw->mac.type >= e1000_pch_cnp &&
6952 !e1000e_check_me(hw->adapter->pdev->device))
6953 e1000e_s0ix_entry_flow(adapter);
6954
6955 return rc;
6956}
6957
6958static __maybe_unused int e1000e_pm_resume(struct device *dev)
6959{
6960 struct net_device *netdev = pci_get_drvdata(to_pci_dev(dev));
6961 struct e1000_adapter *adapter = netdev_priv(netdev);
6962 struct pci_dev *pdev = to_pci_dev(dev);
6963 struct e1000_hw *hw = &adapter->hw;
6964 int rc;
6965
6966 /* Introduce S0ix implementation */
6967 if (hw->mac.type >= e1000_pch_cnp &&
6968 !e1000e_check_me(hw->adapter->pdev->device))
6969 e1000e_s0ix_exit_flow(adapter);
6970
6971 rc = __e1000_resume(pdev);
6972 if (rc)
6973 return rc;
6974
6975 return e1000e_pm_thaw(dev);
6976}
6977
6978static __maybe_unused int e1000e_pm_runtime_idle(struct device *dev)
6979{
6980 struct net_device *netdev = dev_get_drvdata(dev);
6981 struct e1000_adapter *adapter = netdev_priv(netdev);
6982 u16 eee_lp;
6983
6984 eee_lp = adapter->hw.dev_spec.ich8lan.eee_lp_ability;
6985
6986 if (!e1000e_has_link(adapter)) {
6987 adapter->hw.dev_spec.ich8lan.eee_lp_ability = eee_lp;
6988 pm_schedule_suspend(dev, 5 * MSEC_PER_SEC);
6989 }
6990
6991 return -EBUSY;
6992}
6993
6994static __maybe_unused int e1000e_pm_runtime_resume(struct device *dev)
6995{
6996 struct pci_dev *pdev = to_pci_dev(dev);
6997 struct net_device *netdev = pci_get_drvdata(pdev);
6998 struct e1000_adapter *adapter = netdev_priv(netdev);
6999 int rc;
7000
7001 rc = __e1000_resume(pdev);
7002 if (rc)
7003 return rc;
7004
7005 if (netdev->flags & IFF_UP)
7006 e1000e_up(adapter);
7007
7008 return rc;
7009}
7010
7011static __maybe_unused int e1000e_pm_runtime_suspend(struct device *dev)
7012{
7013 struct pci_dev *pdev = to_pci_dev(dev);
7014 struct net_device *netdev = pci_get_drvdata(pdev);
7015 struct e1000_adapter *adapter = netdev_priv(netdev);
7016
7017 if (netdev->flags & IFF_UP) {
7018 int count = E1000_CHECK_RESET_COUNT;
7019
7020 while (test_bit(__E1000_RESETTING, &adapter->state) && count--)
7021 usleep_range(10000, 11000);
7022
7023 WARN_ON(test_bit(__E1000_RESETTING, &adapter->state));
7024
7025 /* Down the device without resetting the hardware */
7026 e1000e_down(adapter, false);
7027 }
7028
7029 if (__e1000_shutdown(pdev, true)) {
7030 e1000e_pm_runtime_resume(dev);
7031 return -EBUSY;
7032 }
7033
7034 return 0;
7035}
7036
7037static void e1000_shutdown(struct pci_dev *pdev)
7038{
7039 e1000e_flush_lpic(pdev);
7040
7041 e1000e_pm_freeze(&pdev->dev);
7042
7043 __e1000_shutdown(pdev, false);
7044}
7045
7046#ifdef CONFIG_NET_POLL_CONTROLLER
7047
7048static irqreturn_t e1000_intr_msix(int __always_unused irq, void *data)
7049{
7050 struct net_device *netdev = data;
7051 struct e1000_adapter *adapter = netdev_priv(netdev);
7052
7053 if (adapter->msix_entries) {
7054 int vector, msix_irq;
7055
7056 vector = 0;
7057 msix_irq = adapter->msix_entries[vector].vector;
7058 if (disable_hardirq(msix_irq))
7059 e1000_intr_msix_rx(msix_irq, netdev);
7060 enable_irq(msix_irq);
7061
7062 vector++;
7063 msix_irq = adapter->msix_entries[vector].vector;
7064 if (disable_hardirq(msix_irq))
7065 e1000_intr_msix_tx(msix_irq, netdev);
7066 enable_irq(msix_irq);
7067
7068 vector++;
7069 msix_irq = adapter->msix_entries[vector].vector;
7070 if (disable_hardirq(msix_irq))
7071 e1000_msix_other(msix_irq, netdev);
7072 enable_irq(msix_irq);
7073 }
7074
7075 return IRQ_HANDLED;
7076}
7077
7078/**
7079 * e1000_netpoll
7080 * @netdev: network interface device structure
7081 *
7082 * Polling 'interrupt' - used by things like netconsole to send skbs
7083 * without having to re-enable interrupts. It's not called while
7084 * the interrupt routine is executing.
7085 */
7086static void e1000_netpoll(struct net_device *netdev)
7087{
7088 struct e1000_adapter *adapter = netdev_priv(netdev);
7089
7090 switch (adapter->int_mode) {
7091 case E1000E_INT_MODE_MSIX:
7092 e1000_intr_msix(adapter->pdev->irq, netdev);
7093 break;
7094 case E1000E_INT_MODE_MSI:
7095 if (disable_hardirq(adapter->pdev->irq))
7096 e1000_intr_msi(adapter->pdev->irq, netdev);
7097 enable_irq(adapter->pdev->irq);
7098 break;
7099 default: /* E1000E_INT_MODE_LEGACY */
7100 if (disable_hardirq(adapter->pdev->irq))
7101 e1000_intr(adapter->pdev->irq, netdev);
7102 enable_irq(adapter->pdev->irq);
7103 break;
7104 }
7105}
7106#endif
7107
7108/**
7109 * e1000_io_error_detected - called when PCI error is detected
7110 * @pdev: Pointer to PCI device
7111 * @state: The current pci connection state
7112 *
7113 * This function is called after a PCI bus error affecting
7114 * this device has been detected.
7115 */
7116static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev,
7117 pci_channel_state_t state)
7118{
7119 e1000e_pm_freeze(&pdev->dev);
7120
7121 if (state == pci_channel_io_perm_failure)
7122 return PCI_ERS_RESULT_DISCONNECT;
7123
7124 pci_disable_device(pdev);
7125
7126 /* Request a slot slot reset. */
7127 return PCI_ERS_RESULT_NEED_RESET;
7128}
7129
7130/**
7131 * e1000_io_slot_reset - called after the pci bus has been reset.
7132 * @pdev: Pointer to PCI device
7133 *
7134 * Restart the card from scratch, as if from a cold-boot. Implementation
7135 * resembles the first-half of the e1000e_pm_resume routine.
7136 */
7137static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev)
7138{
7139 struct net_device *netdev = pci_get_drvdata(pdev);
7140 struct e1000_adapter *adapter = netdev_priv(netdev);
7141 struct e1000_hw *hw = &adapter->hw;
7142 u16 aspm_disable_flag = 0;
7143 int err;
7144 pci_ers_result_t result;
7145
7146 if (adapter->flags2 & FLAG2_DISABLE_ASPM_L0S)
7147 aspm_disable_flag = PCIE_LINK_STATE_L0S;
7148 if (adapter->flags2 & FLAG2_DISABLE_ASPM_L1)
7149 aspm_disable_flag |= PCIE_LINK_STATE_L1;
7150 if (aspm_disable_flag)
7151 e1000e_disable_aspm_locked(pdev, aspm_disable_flag);
7152
7153 err = pci_enable_device_mem(pdev);
7154 if (err) {
7155 dev_err(&pdev->dev,
7156 "Cannot re-enable PCI device after reset.\n");
7157 result = PCI_ERS_RESULT_DISCONNECT;
7158 } else {
7159 pdev->state_saved = true;
7160 pci_restore_state(pdev);
7161 pci_set_master(pdev);
7162
7163 pci_enable_wake(pdev, PCI_D3hot, 0);
7164 pci_enable_wake(pdev, PCI_D3cold, 0);
7165
7166 e1000e_reset(adapter);
7167 ew32(WUS, ~0);
7168 result = PCI_ERS_RESULT_RECOVERED;
7169 }
7170
7171 return result;
7172}
7173
7174/**
7175 * e1000_io_resume - called when traffic can start flowing again.
7176 * @pdev: Pointer to PCI device
7177 *
7178 * This callback is called when the error recovery driver tells us that
7179 * its OK to resume normal operation. Implementation resembles the
7180 * second-half of the e1000e_pm_resume routine.
7181 */
7182static void e1000_io_resume(struct pci_dev *pdev)
7183{
7184 struct net_device *netdev = pci_get_drvdata(pdev);
7185 struct e1000_adapter *adapter = netdev_priv(netdev);
7186
7187 e1000_init_manageability_pt(adapter);
7188
7189 e1000e_pm_thaw(&pdev->dev);
7190
7191 /* If the controller has AMT, do not set DRV_LOAD until the interface
7192 * is up. For all other cases, let the f/w know that the h/w is now
7193 * under the control of the driver.
7194 */
7195 if (!(adapter->flags & FLAG_HAS_AMT))
7196 e1000e_get_hw_control(adapter);
7197}
7198
7199static void e1000_print_device_info(struct e1000_adapter *adapter)
7200{
7201 struct e1000_hw *hw = &adapter->hw;
7202 struct net_device *netdev = adapter->netdev;
7203 u32 ret_val;
7204 u8 pba_str[E1000_PBANUM_LENGTH];
7205
7206 /* print bus type/speed/width info */
7207 e_info("(PCI Express:2.5GT/s:%s) %pM\n",
7208 /* bus width */
7209 ((hw->bus.width == e1000_bus_width_pcie_x4) ? "Width x4" :
7210 "Width x1"),
7211 /* MAC address */
7212 netdev->dev_addr);
7213 e_info("Intel(R) PRO/%s Network Connection\n",
7214 (hw->phy.type == e1000_phy_ife) ? "10/100" : "1000");
7215 ret_val = e1000_read_pba_string_generic(hw, pba_str,
7216 E1000_PBANUM_LENGTH);
7217 if (ret_val)
7218 strlcpy((char *)pba_str, "Unknown", sizeof(pba_str));
7219 e_info("MAC: %d, PHY: %d, PBA No: %s\n",
7220 hw->mac.type, hw->phy.type, pba_str);
7221}
7222
7223static void e1000_eeprom_checks(struct e1000_adapter *adapter)
7224{
7225 struct e1000_hw *hw = &adapter->hw;
7226 int ret_val;
7227 u16 buf = 0;
7228
7229 if (hw->mac.type != e1000_82573)
7230 return;
7231
7232 ret_val = e1000_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &buf);
7233 le16_to_cpus(&buf);
7234 if (!ret_val && (!(buf & BIT(0)))) {
7235 /* Deep Smart Power Down (DSPD) */
7236 dev_warn(&adapter->pdev->dev,
7237 "Warning: detected DSPD enabled in EEPROM\n");
7238 }
7239}
7240
7241static netdev_features_t e1000_fix_features(struct net_device *netdev,
7242 netdev_features_t features)
7243{
7244 struct e1000_adapter *adapter = netdev_priv(netdev);
7245 struct e1000_hw *hw = &adapter->hw;
7246
7247 /* Jumbo frame workaround on 82579 and newer requires CRC be stripped */
7248 if ((hw->mac.type >= e1000_pch2lan) && (netdev->mtu > ETH_DATA_LEN))
7249 features &= ~NETIF_F_RXFCS;
7250
7251 /* Since there is no support for separate Rx/Tx vlan accel
7252 * enable/disable make sure Tx flag is always in same state as Rx.
7253 */
7254 if (features & NETIF_F_HW_VLAN_CTAG_RX)
7255 features |= NETIF_F_HW_VLAN_CTAG_TX;
7256 else
7257 features &= ~NETIF_F_HW_VLAN_CTAG_TX;
7258
7259 return features;
7260}
7261
7262static int e1000_set_features(struct net_device *netdev,
7263 netdev_features_t features)
7264{
7265 struct e1000_adapter *adapter = netdev_priv(netdev);
7266 netdev_features_t changed = features ^ netdev->features;
7267
7268 if (changed & (NETIF_F_TSO | NETIF_F_TSO6))
7269 adapter->flags |= FLAG_TSO_FORCE;
7270
7271 if (!(changed & (NETIF_F_HW_VLAN_CTAG_RX | NETIF_F_HW_VLAN_CTAG_TX |
7272 NETIF_F_RXCSUM | NETIF_F_RXHASH | NETIF_F_RXFCS |
7273 NETIF_F_RXALL)))
7274 return 0;
7275
7276 if (changed & NETIF_F_RXFCS) {
7277 if (features & NETIF_F_RXFCS) {
7278 adapter->flags2 &= ~FLAG2_CRC_STRIPPING;
7279 } else {
7280 /* We need to take it back to defaults, which might mean
7281 * stripping is still disabled at the adapter level.
7282 */
7283 if (adapter->flags2 & FLAG2_DFLT_CRC_STRIPPING)
7284 adapter->flags2 |= FLAG2_CRC_STRIPPING;
7285 else
7286 adapter->flags2 &= ~FLAG2_CRC_STRIPPING;
7287 }
7288 }
7289
7290 netdev->features = features;
7291
7292 if (netif_running(netdev))
7293 e1000e_reinit_locked(adapter);
7294 else
7295 e1000e_reset(adapter);
7296
7297 return 1;
7298}
7299
7300static const struct net_device_ops e1000e_netdev_ops = {
7301 .ndo_open = e1000e_open,
7302 .ndo_stop = e1000e_close,
7303 .ndo_start_xmit = e1000_xmit_frame,
7304 .ndo_get_stats64 = e1000e_get_stats64,
7305 .ndo_set_rx_mode = e1000e_set_rx_mode,
7306 .ndo_set_mac_address = e1000_set_mac,
7307 .ndo_change_mtu = e1000_change_mtu,
7308 .ndo_do_ioctl = e1000_ioctl,
7309 .ndo_tx_timeout = e1000_tx_timeout,
7310 .ndo_validate_addr = eth_validate_addr,
7311
7312 .ndo_vlan_rx_add_vid = e1000_vlan_rx_add_vid,
7313 .ndo_vlan_rx_kill_vid = e1000_vlan_rx_kill_vid,
7314#ifdef CONFIG_NET_POLL_CONTROLLER
7315 .ndo_poll_controller = e1000_netpoll,
7316#endif
7317 .ndo_set_features = e1000_set_features,
7318 .ndo_fix_features = e1000_fix_features,
7319 .ndo_features_check = passthru_features_check,
7320};
7321
7322/**
7323 * e1000_probe - Device Initialization Routine
7324 * @pdev: PCI device information struct
7325 * @ent: entry in e1000_pci_tbl
7326 *
7327 * Returns 0 on success, negative on failure
7328 *
7329 * e1000_probe initializes an adapter identified by a pci_dev structure.
7330 * The OS initialization, configuring of the adapter private structure,
7331 * and a hardware reset occur.
7332 **/
7333static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
7334{
7335 struct net_device *netdev;
7336 struct e1000_adapter *adapter;
7337 struct e1000_hw *hw;
7338 const struct e1000_info *ei = e1000_info_tbl[ent->driver_data];
7339 resource_size_t mmio_start, mmio_len;
7340 resource_size_t flash_start, flash_len;
7341 static int cards_found;
7342 u16 aspm_disable_flag = 0;
7343 int bars, i, err, pci_using_dac;
7344 u16 eeprom_data = 0;
7345 u16 eeprom_apme_mask = E1000_EEPROM_APME;
7346 s32 ret_val = 0;
7347
7348 if (ei->flags2 & FLAG2_DISABLE_ASPM_L0S)
7349 aspm_disable_flag = PCIE_LINK_STATE_L0S;
7350 if (ei->flags2 & FLAG2_DISABLE_ASPM_L1)
7351 aspm_disable_flag |= PCIE_LINK_STATE_L1;
7352 if (aspm_disable_flag)
7353 e1000e_disable_aspm(pdev, aspm_disable_flag);
7354
7355 err = pci_enable_device_mem(pdev);
7356 if (err)
7357 return err;
7358
7359 pci_using_dac = 0;
7360 err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
7361 if (!err) {
7362 pci_using_dac = 1;
7363 } else {
7364 err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
7365 if (err) {
7366 dev_err(&pdev->dev,
7367 "No usable DMA configuration, aborting\n");
7368 goto err_dma;
7369 }
7370 }
7371
7372 bars = pci_select_bars(pdev, IORESOURCE_MEM);
7373 err = pci_request_selected_regions_exclusive(pdev, bars,
7374 e1000e_driver_name);
7375 if (err)
7376 goto err_pci_reg;
7377
7378 /* AER (Advanced Error Reporting) hooks */
7379 pci_enable_pcie_error_reporting(pdev);
7380
7381 pci_set_master(pdev);
7382 /* PCI config space info */
7383 err = pci_save_state(pdev);
7384 if (err)
7385 goto err_alloc_etherdev;
7386
7387 err = -ENOMEM;
7388 netdev = alloc_etherdev(sizeof(struct e1000_adapter));
7389 if (!netdev)
7390 goto err_alloc_etherdev;
7391
7392 SET_NETDEV_DEV(netdev, &pdev->dev);
7393
7394 netdev->irq = pdev->irq;
7395
7396 pci_set_drvdata(pdev, netdev);
7397 adapter = netdev_priv(netdev);
7398 hw = &adapter->hw;
7399 adapter->netdev = netdev;
7400 adapter->pdev = pdev;
7401 adapter->ei = ei;
7402 adapter->pba = ei->pba;
7403 adapter->flags = ei->flags;
7404 adapter->flags2 = ei->flags2;
7405 adapter->hw.adapter = adapter;
7406 adapter->hw.mac.type = ei->mac;
7407 adapter->max_hw_frame_size = ei->max_hw_frame_size;
7408 adapter->msg_enable = netif_msg_init(debug, DEFAULT_MSG_ENABLE);
7409
7410 mmio_start = pci_resource_start(pdev, 0);
7411 mmio_len = pci_resource_len(pdev, 0);
7412
7413 err = -EIO;
7414 adapter->hw.hw_addr = ioremap(mmio_start, mmio_len);
7415 if (!adapter->hw.hw_addr)
7416 goto err_ioremap;
7417
7418 if ((adapter->flags & FLAG_HAS_FLASH) &&
7419 (pci_resource_flags(pdev, 1) & IORESOURCE_MEM) &&
7420 (hw->mac.type < e1000_pch_spt)) {
7421 flash_start = pci_resource_start(pdev, 1);
7422 flash_len = pci_resource_len(pdev, 1);
7423 adapter->hw.flash_address = ioremap(flash_start, flash_len);
7424 if (!adapter->hw.flash_address)
7425 goto err_flashmap;
7426 }
7427
7428 /* Set default EEE advertisement */
7429 if (adapter->flags2 & FLAG2_HAS_EEE)
7430 adapter->eee_advert = MDIO_EEE_100TX | MDIO_EEE_1000T;
7431
7432 /* construct the net_device struct */
7433 netdev->netdev_ops = &e1000e_netdev_ops;
7434 e1000e_set_ethtool_ops(netdev);
7435 netdev->watchdog_timeo = 5 * HZ;
7436 netif_napi_add(netdev, &adapter->napi, e1000e_poll, 64);
7437 strlcpy(netdev->name, pci_name(pdev), sizeof(netdev->name));
7438
7439 netdev->mem_start = mmio_start;
7440 netdev->mem_end = mmio_start + mmio_len;
7441
7442 adapter->bd_number = cards_found++;
7443
7444 e1000e_check_options(adapter);
7445
7446 /* setup adapter struct */
7447 err = e1000_sw_init(adapter);
7448 if (err)
7449 goto err_sw_init;
7450
7451 memcpy(&hw->mac.ops, ei->mac_ops, sizeof(hw->mac.ops));
7452 memcpy(&hw->nvm.ops, ei->nvm_ops, sizeof(hw->nvm.ops));
7453 memcpy(&hw->phy.ops, ei->phy_ops, sizeof(hw->phy.ops));
7454
7455 err = ei->get_variants(adapter);
7456 if (err)
7457 goto err_hw_init;
7458
7459 if ((adapter->flags & FLAG_IS_ICH) &&
7460 (adapter->flags & FLAG_READ_ONLY_NVM) &&
7461 (hw->mac.type < e1000_pch_spt))
7462 e1000e_write_protect_nvm_ich8lan(&adapter->hw);
7463
7464 hw->mac.ops.get_bus_info(&adapter->hw);
7465
7466 adapter->hw.phy.autoneg_wait_to_complete = 0;
7467
7468 /* Copper options */
7469 if (adapter->hw.phy.media_type == e1000_media_type_copper) {
7470 adapter->hw.phy.mdix = AUTO_ALL_MODES;
7471 adapter->hw.phy.disable_polarity_correction = 0;
7472 adapter->hw.phy.ms_type = e1000_ms_hw_default;
7473 }
7474
7475 if (hw->phy.ops.check_reset_block && hw->phy.ops.check_reset_block(hw))
7476 dev_info(&pdev->dev,
7477 "PHY reset is blocked due to SOL/IDER session.\n");
7478
7479 /* Set initial default active device features */
7480 netdev->features = (NETIF_F_SG |
7481 NETIF_F_HW_VLAN_CTAG_RX |
7482 NETIF_F_HW_VLAN_CTAG_TX |
7483 NETIF_F_TSO |
7484 NETIF_F_TSO6 |
7485 NETIF_F_RXHASH |
7486 NETIF_F_RXCSUM |
7487 NETIF_F_HW_CSUM);
7488
7489 /* Set user-changeable features (subset of all device features) */
7490 netdev->hw_features = netdev->features;
7491 netdev->hw_features |= NETIF_F_RXFCS;
7492 netdev->priv_flags |= IFF_SUPP_NOFCS;
7493 netdev->hw_features |= NETIF_F_RXALL;
7494
7495 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER)
7496 netdev->features |= NETIF_F_HW_VLAN_CTAG_FILTER;
7497
7498 netdev->vlan_features |= (NETIF_F_SG |
7499 NETIF_F_TSO |
7500 NETIF_F_TSO6 |
7501 NETIF_F_HW_CSUM);
7502
7503 netdev->priv_flags |= IFF_UNICAST_FLT;
7504
7505 if (pci_using_dac) {
7506 netdev->features |= NETIF_F_HIGHDMA;
7507 netdev->vlan_features |= NETIF_F_HIGHDMA;
7508 }
7509
7510 /* MTU range: 68 - max_hw_frame_size */
7511 netdev->min_mtu = ETH_MIN_MTU;
7512 netdev->max_mtu = adapter->max_hw_frame_size -
7513 (VLAN_ETH_HLEN + ETH_FCS_LEN);
7514
7515 if (e1000e_enable_mng_pass_thru(&adapter->hw))
7516 adapter->flags |= FLAG_MNG_PT_ENABLED;
7517
7518 /* before reading the NVM, reset the controller to
7519 * put the device in a known good starting state
7520 */
7521 adapter->hw.mac.ops.reset_hw(&adapter->hw);
7522
7523 /* systems with ASPM and others may see the checksum fail on the first
7524 * attempt. Let's give it a few tries
7525 */
7526 for (i = 0;; i++) {
7527 if (e1000_validate_nvm_checksum(&adapter->hw) >= 0)
7528 break;
7529 if (i == 2) {
7530 dev_err(&pdev->dev, "The NVM Checksum Is Not Valid\n");
7531 err = -EIO;
7532 goto err_eeprom;
7533 }
7534 }
7535
7536 e1000_eeprom_checks(adapter);
7537
7538 /* copy the MAC address */
7539 if (e1000e_read_mac_addr(&adapter->hw))
7540 dev_err(&pdev->dev,
7541 "NVM Read Error while reading MAC address\n");
7542
7543 memcpy(netdev->dev_addr, adapter->hw.mac.addr, netdev->addr_len);
7544
7545 if (!is_valid_ether_addr(netdev->dev_addr)) {
7546 dev_err(&pdev->dev, "Invalid MAC Address: %pM\n",
7547 netdev->dev_addr);
7548 err = -EIO;
7549 goto err_eeprom;
7550 }
7551
7552 timer_setup(&adapter->watchdog_timer, e1000_watchdog, 0);
7553 timer_setup(&adapter->phy_info_timer, e1000_update_phy_info, 0);
7554
7555 INIT_WORK(&adapter->reset_task, e1000_reset_task);
7556 INIT_WORK(&adapter->watchdog_task, e1000_watchdog_task);
7557 INIT_WORK(&adapter->downshift_task, e1000e_downshift_workaround);
7558 INIT_WORK(&adapter->update_phy_task, e1000e_update_phy_task);
7559 INIT_WORK(&adapter->print_hang_task, e1000_print_hw_hang);
7560
7561 /* Initialize link parameters. User can change them with ethtool */
7562 adapter->hw.mac.autoneg = 1;
7563 adapter->fc_autoneg = true;
7564 adapter->hw.fc.requested_mode = e1000_fc_default;
7565 adapter->hw.fc.current_mode = e1000_fc_default;
7566 adapter->hw.phy.autoneg_advertised = 0x2f;
7567
7568 /* Initial Wake on LAN setting - If APM wake is enabled in
7569 * the EEPROM, enable the ACPI Magic Packet filter
7570 */
7571 if (adapter->flags & FLAG_APME_IN_WUC) {
7572 /* APME bit in EEPROM is mapped to WUC.APME */
7573 eeprom_data = er32(WUC);
7574 eeprom_apme_mask = E1000_WUC_APME;
7575 if ((hw->mac.type > e1000_ich10lan) &&
7576 (eeprom_data & E1000_WUC_PHY_WAKE))
7577 adapter->flags2 |= FLAG2_HAS_PHY_WAKEUP;
7578 } else if (adapter->flags & FLAG_APME_IN_CTRL3) {
7579 if (adapter->flags & FLAG_APME_CHECK_PORT_B &&
7580 (adapter->hw.bus.func == 1))
7581 ret_val = e1000_read_nvm(&adapter->hw,
7582 NVM_INIT_CONTROL3_PORT_B,
7583 1, &eeprom_data);
7584 else
7585 ret_val = e1000_read_nvm(&adapter->hw,
7586 NVM_INIT_CONTROL3_PORT_A,
7587 1, &eeprom_data);
7588 }
7589
7590 /* fetch WoL from EEPROM */
7591 if (ret_val)
7592 e_dbg("NVM read error getting WoL initial values: %d\n", ret_val);
7593 else if (eeprom_data & eeprom_apme_mask)
7594 adapter->eeprom_wol |= E1000_WUFC_MAG;
7595
7596 /* now that we have the eeprom settings, apply the special cases
7597 * where the eeprom may be wrong or the board simply won't support
7598 * wake on lan on a particular port
7599 */
7600 if (!(adapter->flags & FLAG_HAS_WOL))
7601 adapter->eeprom_wol = 0;
7602
7603 /* initialize the wol settings based on the eeprom settings */
7604 adapter->wol = adapter->eeprom_wol;
7605
7606 /* make sure adapter isn't asleep if manageability is enabled */
7607 if (adapter->wol || (adapter->flags & FLAG_MNG_PT_ENABLED) ||
7608 (hw->mac.ops.check_mng_mode(hw)))
7609 device_wakeup_enable(&pdev->dev);
7610
7611 /* save off EEPROM version number */
7612 ret_val = e1000_read_nvm(&adapter->hw, 5, 1, &adapter->eeprom_vers);
7613
7614 if (ret_val) {
7615 e_dbg("NVM read error getting EEPROM version: %d\n", ret_val);
7616 adapter->eeprom_vers = 0;
7617 }
7618
7619 /* init PTP hardware clock */
7620 e1000e_ptp_init(adapter);
7621
7622 /* reset the hardware with the new settings */
7623 e1000e_reset(adapter);
7624
7625 /* If the controller has AMT, do not set DRV_LOAD until the interface
7626 * is up. For all other cases, let the f/w know that the h/w is now
7627 * under the control of the driver.
7628 */
7629 if (!(adapter->flags & FLAG_HAS_AMT))
7630 e1000e_get_hw_control(adapter);
7631
7632 strlcpy(netdev->name, "eth%d", sizeof(netdev->name));
7633 err = register_netdev(netdev);
7634 if (err)
7635 goto err_register;
7636
7637 /* carrier off reporting is important to ethtool even BEFORE open */
7638 netif_carrier_off(netdev);
7639
7640 e1000_print_device_info(adapter);
7641
7642 dev_pm_set_driver_flags(&pdev->dev, DPM_FLAG_NO_DIRECT_COMPLETE);
7643
7644 if (pci_dev_run_wake(pdev) && hw->mac.type < e1000_pch_cnp)
7645 pm_runtime_put_noidle(&pdev->dev);
7646
7647 return 0;
7648
7649err_register:
7650 if (!(adapter->flags & FLAG_HAS_AMT))
7651 e1000e_release_hw_control(adapter);
7652err_eeprom:
7653 if (hw->phy.ops.check_reset_block && !hw->phy.ops.check_reset_block(hw))
7654 e1000_phy_hw_reset(&adapter->hw);
7655err_hw_init:
7656 kfree(adapter->tx_ring);
7657 kfree(adapter->rx_ring);
7658err_sw_init:
7659 if ((adapter->hw.flash_address) && (hw->mac.type < e1000_pch_spt))
7660 iounmap(adapter->hw.flash_address);
7661 e1000e_reset_interrupt_capability(adapter);
7662err_flashmap:
7663 iounmap(adapter->hw.hw_addr);
7664err_ioremap:
7665 free_netdev(netdev);
7666err_alloc_etherdev:
7667 pci_release_mem_regions(pdev);
7668err_pci_reg:
7669err_dma:
7670 pci_disable_device(pdev);
7671 return err;
7672}
7673
7674/**
7675 * e1000_remove - Device Removal Routine
7676 * @pdev: PCI device information struct
7677 *
7678 * e1000_remove is called by the PCI subsystem to alert the driver
7679 * that it should release a PCI device. The could be caused by a
7680 * Hot-Plug event, or because the driver is going to be removed from
7681 * memory.
7682 **/
7683static void e1000_remove(struct pci_dev *pdev)
7684{
7685 struct net_device *netdev = pci_get_drvdata(pdev);
7686 struct e1000_adapter *adapter = netdev_priv(netdev);
7687
7688 e1000e_ptp_remove(adapter);
7689
7690 /* The timers may be rescheduled, so explicitly disable them
7691 * from being rescheduled.
7692 */
7693 set_bit(__E1000_DOWN, &adapter->state);
7694 del_timer_sync(&adapter->watchdog_timer);
7695 del_timer_sync(&adapter->phy_info_timer);
7696
7697 cancel_work_sync(&adapter->reset_task);
7698 cancel_work_sync(&adapter->watchdog_task);
7699 cancel_work_sync(&adapter->downshift_task);
7700 cancel_work_sync(&adapter->update_phy_task);
7701 cancel_work_sync(&adapter->print_hang_task);
7702
7703 if (adapter->flags & FLAG_HAS_HW_TIMESTAMP) {
7704 cancel_work_sync(&adapter->tx_hwtstamp_work);
7705 if (adapter->tx_hwtstamp_skb) {
7706 dev_consume_skb_any(adapter->tx_hwtstamp_skb);
7707 adapter->tx_hwtstamp_skb = NULL;
7708 }
7709 }
7710
7711 unregister_netdev(netdev);
7712
7713 if (pci_dev_run_wake(pdev))
7714 pm_runtime_get_noresume(&pdev->dev);
7715
7716 /* Release control of h/w to f/w. If f/w is AMT enabled, this
7717 * would have already happened in close and is redundant.
7718 */
7719 e1000e_release_hw_control(adapter);
7720
7721 e1000e_reset_interrupt_capability(adapter);
7722 kfree(adapter->tx_ring);
7723 kfree(adapter->rx_ring);
7724
7725 iounmap(adapter->hw.hw_addr);
7726 if ((adapter->hw.flash_address) &&
7727 (adapter->hw.mac.type < e1000_pch_spt))
7728 iounmap(adapter->hw.flash_address);
7729 pci_release_mem_regions(pdev);
7730
7731 free_netdev(netdev);
7732
7733 /* AER disable */
7734 pci_disable_pcie_error_reporting(pdev);
7735
7736 pci_disable_device(pdev);
7737}
7738
7739/* PCI Error Recovery (ERS) */
7740static const struct pci_error_handlers e1000_err_handler = {
7741 .error_detected = e1000_io_error_detected,
7742 .slot_reset = e1000_io_slot_reset,
7743 .resume = e1000_io_resume,
7744};
7745
7746static const struct pci_device_id e1000_pci_tbl[] = {
7747 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_COPPER), board_82571 },
7748 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_FIBER), board_82571 },
7749 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_COPPER), board_82571 },
7750 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_COPPER_LP),
7751 board_82571 },
7752 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_FIBER), board_82571 },
7753 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES), board_82571 },
7754 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES_DUAL), board_82571 },
7755 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES_QUAD), board_82571 },
7756 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571PT_QUAD_COPPER), board_82571 },
7757
7758 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI), board_82572 },
7759 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_COPPER), board_82572 },
7760 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_FIBER), board_82572 },
7761 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_SERDES), board_82572 },
7762
7763 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573E), board_82573 },
7764 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573E_IAMT), board_82573 },
7765 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573L), board_82573 },
7766
7767 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82574L), board_82574 },
7768 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82574LA), board_82574 },
7769 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82583V), board_82583 },
7770
7771 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_COPPER_DPT),
7772 board_80003es2lan },
7773 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_COPPER_SPT),
7774 board_80003es2lan },
7775 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_SERDES_DPT),
7776 board_80003es2lan },
7777 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_SERDES_SPT),
7778 board_80003es2lan },
7779
7780 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE), board_ich8lan },
7781 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE_G), board_ich8lan },
7782 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE_GT), board_ich8lan },
7783 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_AMT), board_ich8lan },
7784 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_C), board_ich8lan },
7785 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_M), board_ich8lan },
7786 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_M_AMT), board_ich8lan },
7787 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_82567V_3), board_ich8lan },
7788
7789 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE), board_ich9lan },
7790 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE_G), board_ich9lan },
7791 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE_GT), board_ich9lan },
7792 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_AMT), board_ich9lan },
7793 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_C), board_ich9lan },
7794 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_BM), board_ich9lan },
7795 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M), board_ich9lan },
7796 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M_AMT), board_ich9lan },
7797 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M_V), board_ich9lan },
7798
7799 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_LM), board_ich9lan },
7800 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_LF), board_ich9lan },
7801 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_V), board_ich9lan },
7802
7803 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LM), board_ich10lan },
7804 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_LF), board_ich10lan },
7805 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_D_BM_V), board_ich10lan },
7806
7807 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_M_HV_LM), board_pchlan },
7808 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_M_HV_LC), board_pchlan },
7809 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_D_HV_DM), board_pchlan },
7810 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_D_HV_DC), board_pchlan },
7811
7812 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH2_LV_LM), board_pch2lan },
7813 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH2_LV_V), board_pch2lan },
7814
7815 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LPT_I217_LM), board_pch_lpt },
7816 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LPT_I217_V), board_pch_lpt },
7817 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LPTLP_I218_LM), board_pch_lpt },
7818 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LPTLP_I218_V), board_pch_lpt },
7819 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_I218_LM2), board_pch_lpt },
7820 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_I218_V2), board_pch_lpt },
7821 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_I218_LM3), board_pch_lpt },
7822 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_I218_V3), board_pch_lpt },
7823 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_LM), board_pch_spt },
7824 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_V), board_pch_spt },
7825 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_LM2), board_pch_spt },
7826 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_V2), board_pch_spt },
7827 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_LBG_I219_LM3), board_pch_spt },
7828 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_LM4), board_pch_spt },
7829 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_V4), board_pch_spt },
7830 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_LM5), board_pch_spt },
7831 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_SPT_I219_V5), board_pch_spt },
7832 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CNP_I219_LM6), board_pch_cnp },
7833 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CNP_I219_V6), board_pch_cnp },
7834 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CNP_I219_LM7), board_pch_cnp },
7835 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CNP_I219_V7), board_pch_cnp },
7836 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ICP_I219_LM8), board_pch_cnp },
7837 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ICP_I219_V8), board_pch_cnp },
7838 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ICP_I219_LM9), board_pch_cnp },
7839 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ICP_I219_V9), board_pch_cnp },
7840 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_LM10), board_pch_cnp },
7841 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_V10), board_pch_cnp },
7842 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_LM11), board_pch_cnp },
7843 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_V11), board_pch_cnp },
7844 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_LM12), board_pch_spt },
7845 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_CMP_I219_V12), board_pch_spt },
7846 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_LM13), board_pch_cnp },
7847 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_V13), board_pch_cnp },
7848 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_LM14), board_pch_cnp },
7849 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_V14), board_pch_cnp },
7850 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_LM15), board_pch_cnp },
7851 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_TGP_I219_V15), board_pch_cnp },
7852 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_LM16), board_pch_cnp },
7853 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_V16), board_pch_cnp },
7854 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_LM17), board_pch_cnp },
7855 { PCI_VDEVICE(INTEL, E1000_DEV_ID_PCH_ADP_I219_V17), board_pch_cnp },
7856
7857 { 0, 0, 0, 0, 0, 0, 0 } /* terminate list */
7858};
7859MODULE_DEVICE_TABLE(pci, e1000_pci_tbl);
7860
7861static const struct dev_pm_ops e1000_pm_ops = {
7862#ifdef CONFIG_PM_SLEEP
7863 .suspend = e1000e_pm_suspend,
7864 .resume = e1000e_pm_resume,
7865 .freeze = e1000e_pm_freeze,
7866 .thaw = e1000e_pm_thaw,
7867 .poweroff = e1000e_pm_suspend,
7868 .restore = e1000e_pm_resume,
7869#endif
7870 SET_RUNTIME_PM_OPS(e1000e_pm_runtime_suspend, e1000e_pm_runtime_resume,
7871 e1000e_pm_runtime_idle)
7872};
7873
7874/* PCI Device API Driver */
7875static struct pci_driver e1000_driver = {
7876 .name = e1000e_driver_name,
7877 .id_table = e1000_pci_tbl,
7878 .probe = e1000_probe,
7879 .remove = e1000_remove,
7880 .driver = {
7881 .pm = &e1000_pm_ops,
7882 },
7883 .shutdown = e1000_shutdown,
7884 .err_handler = &e1000_err_handler
7885};
7886
7887/**
7888 * e1000_init_module - Driver Registration Routine
7889 *
7890 * e1000_init_module is the first routine called when the driver is
7891 * loaded. All it does is register with the PCI subsystem.
7892 **/
7893static int __init e1000_init_module(void)
7894{
7895 pr_info("Intel(R) PRO/1000 Network Driver\n");
7896 pr_info("Copyright(c) 1999 - 2015 Intel Corporation.\n");
7897
7898 return pci_register_driver(&e1000_driver);
7899}
7900module_init(e1000_init_module);
7901
7902/**
7903 * e1000_exit_module - Driver Exit Cleanup Routine
7904 *
7905 * e1000_exit_module is called just before the driver is removed
7906 * from memory.
7907 **/
7908static void __exit e1000_exit_module(void)
7909{
7910 pci_unregister_driver(&e1000_driver);
7911}
7912module_exit(e1000_exit_module);
7913
7914MODULE_AUTHOR("Intel Corporation, <linux.nics@intel.com>");
7915MODULE_DESCRIPTION("Intel(R) PRO/1000 Network Driver");
7916MODULE_LICENSE("GPL v2");
7917
7918/* netdev.c */