1# SPDX-License-Identifier: GPL-2.0-only
  2#
  3# Marvell device configuration
  4#
  5
  6config NET_VENDOR_MARVELL
  7	bool "Marvell devices"
  8	default y
  9	depends on PCI || CPU_PXA168 || MV64X60 || PPC32 || PLAT_ORION || INET || COMPILE_TEST
 10	---help---
 11	  If you have a network (Ethernet) card belonging to this class, say Y.
 12
 13	  Note that the answer to this question doesn't directly affect the
 14	  kernel: saying N will just cause the configurator to skip all
 15	  the questions about Marvell devices. If you say Y, you will be
 16	  asked for your specific card in the following questions.
 17
 18if NET_VENDOR_MARVELL
 19
 20config MV643XX_ETH
 21	tristate "Marvell Discovery (643XX) and Orion ethernet support"
 22	depends on MV64X60 || PPC32 || PLAT_ORION || COMPILE_TEST
 23	depends on INET
 24	select PHYLIB
 25	select MVMDIO
 26	---help---
 27	  This driver supports the gigabit ethernet MACs in the
 28	  Marvell Discovery PPC/MIPS chipset family (MV643XX) and
 29	  in the Marvell Orion ARM SoC family.
 30
 31	  Some boards that use the Discovery chipset are the Momenco
 32	  Ocelot C and Jaguar ATX and Pegasos II.
 33
 34config MVMDIO
 35	tristate "Marvell MDIO interface support"
 36	depends on HAS_IOMEM
 37	select PHYLIB
 38	---help---
 39	  This driver supports the MDIO interface found in the network
 40	  interface units of the Marvell EBU SoCs (Kirkwood, Orion5x,
 41	  Dove, Armada 370 and Armada XP).
 42
 43	  This driver is used by the MV643XX_ETH and MVNETA drivers.
 44
 45config MVNETA_BM_ENABLE
 46	tristate "Marvell Armada 38x/XP network interface BM support"
 47	depends on MVNETA
 48	depends on !64BIT
 49	---help---
 50	  This driver supports auxiliary block of the network
 51	  interface units in the Marvell ARMADA XP and ARMADA 38x SoC
 52	  family, which is called buffer manager.
 53
 54	  This driver, when enabled, strictly cooperates with mvneta
 55	  driver and is common for all network ports of the devices,
 56	  even for Armada 370 SoC, which doesn't support hardware
 57	  buffer management.
 58
 59config MVNETA
 60	tristate "Marvell Armada 370/38x/XP/37xx network interface support"
 61	depends on ARCH_MVEBU || COMPILE_TEST
 62	select MVMDIO
 63	select PHYLINK
 64	---help---
 65	  This driver supports the network interface units in the
 66	  Marvell ARMADA XP, ARMADA 370, ARMADA 38x and
 67	  ARMADA 37xx SoC family.
 68
 69	  Note that this driver is distinct from the mv643xx_eth
 70	  driver, which should be used for the older Marvell SoCs
 71	  (Dove, Orion, Discovery, Kirkwood).
 72
 73config MVNETA_BM
 74	tristate
 75	depends on !64BIT
 76	default y if MVNETA=y && MVNETA_BM_ENABLE!=n
 77	default MVNETA_BM_ENABLE
 78	select HWBM
 79	select GENERIC_ALLOCATOR
 80	help
 81	  MVNETA_BM must not be 'm' if MVNETA=y, so this symbol ensures
 82	  that all dependencies are met.
 83
 84config MVPP2
 85	tristate "Marvell Armada 375/7K/8K network interface support"
 86	depends on ARCH_MVEBU || COMPILE_TEST
 87	select MVMDIO
 88	select PHYLINK
 89	---help---
 90	  This driver supports the network interface units in the
 91	  Marvell ARMADA 375, 7K and 8K SoCs.
 92
 93config PXA168_ETH
 94	tristate "Marvell pxa168 ethernet support"
 95	depends on HAS_IOMEM
 96	depends on CPU_PXA168 || ARCH_BERLIN || COMPILE_TEST
 97	select PHYLIB
 98	---help---
 99	  This driver supports the pxa168 Ethernet ports.
100
101	  To compile this driver as a module, choose M here. The module
102	  will be called pxa168_eth.
103
104config SKGE
105	tristate "Marvell Yukon Gigabit Ethernet support"
106	depends on PCI
107	select CRC32
108	---help---
109	  This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx
110	  and related Gigabit Ethernet adapters. It is a new smaller driver
111	  with better performance and more complete ethtool support.
112
113	  It does not support the link failover and network management
114	  features that "portable" vendor supplied sk98lin driver does.
115
116	  This driver supports adapters based on the original Yukon chipset:
117	  Marvell 88E8001, Belkin F5D5005, CNet GigaCard, DLink DGE-530T,
118	  Linksys EG1032/EG1064, 3Com 3C940/3C940B, SysKonnect SK-9871/9872.
119
120	  It does not support the newer Yukon2 chipset: a separate driver,
121	  sky2, is provided for these adapters.
122
123	  To compile this driver as a module, choose M here: the module
124	  will be called skge.  This is recommended.
125
126config SKGE_DEBUG
127	bool "Debugging interface"
128	depends on SKGE && DEBUG_FS
129	---help---
130	  This option adds the ability to dump driver state for debugging.
131	  The file /sys/kernel/debug/skge/ethX displays the state of the internal
132	  transmit and receive rings.
133
134	  If unsure, say N.
135
136config SKGE_GENESIS
137	bool "Support for older SysKonnect Genesis boards"
138	depends on SKGE
139	---help---
140	 This enables support for the older and uncommon SysKonnect Genesis
141	 chips, which support MII via an external transceiver, instead of
142	 an internal one. Disabling this option will save some memory
143	 by making code smaller. If unsure say Y.
144
145config SKY2
146	tristate "Marvell Yukon 2 support"
147	depends on PCI
148	select CRC32
149	---help---
150	  This driver supports Gigabit Ethernet adapters based on the
151	  Marvell Yukon 2 chipset:
152	  Marvell 88E8021/88E8022/88E8035/88E8036/88E8038/88E8050/88E8052/
153	  88E8053/88E8055/88E8061/88E8062, SysKonnect SK-9E21D/SK-9S21
154
155	  There is companion driver for the older Marvell Yukon and
156	  SysKonnect Genesis based adapters: skge.
157
158	  To compile this driver as a module, choose M here: the module
159	  will be called sky2.  This is recommended.
160
161config SKY2_DEBUG
162	bool "Debugging interface"
163	depends on SKY2 && DEBUG_FS
164	---help---
165	  This option adds the ability to dump driver state for debugging.
166	  The file /sys/kernel/debug/sky2/ethX displays the state of the internal
167	  transmit and receive rings.
168
169	  If unsure, say N.
170
171
172source "drivers/net/ethernet/marvell/octeontx2/Kconfig"
173
174endif # NET_VENDOR_MARVELL