Loading...
1/*
2 * ricoh.h 1.9 1999/10/25 20:03:34
3 *
4 * The contents of this file are subject to the Mozilla Public License
5 * Version 1.1 (the "License"); you may not use this file except in
6 * compliance with the License. You may obtain a copy of the License
7 * at http://www.mozilla.org/MPL/
8 *
9 * Software distributed under the License is distributed on an "AS IS"
10 * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
11 * the License for the specific language governing rights and
12 * limitations under the License.
13 *
14 * The initial developer of the original code is David A. Hinds
15 * <dahinds@users.sourceforge.net>. Portions created by David A. Hinds
16 * are Copyright (C) 1999 David A. Hinds. All Rights Reserved.
17 *
18 * Alternatively, the contents of this file may be used under the
19 * terms of the GNU General Public License version 2 (the "GPL"), in which
20 * case the provisions of the GPL are applicable instead of the
21 * above. If you wish to allow the use of your version of this file
22 * only under the terms of the GPL and not to allow others to use
23 * your version of this file under the MPL, indicate your decision by
24 * deleting the provisions above and replace them with the notice and
25 * other provisions required by the GPL. If you do not delete the
26 * provisions above, a recipient may use your version of this file
27 * under either the MPL or the GPL.
28 */
29
30#ifndef _LINUX_RICOH_H
31#define _LINUX_RICOH_H
32
33
34#define RF5C_MODE_CTL 0x1f /* Mode control */
35#define RF5C_PWR_CTL 0x2f /* Mixed voltage control */
36#define RF5C_CHIP_ID 0x3a /* Chip identification */
37#define RF5C_MODE_CTL_3 0x3b /* Mode control 3 */
38
39/* I/O window address offset */
40#define RF5C_IO_OFF(w) (0x36+((w)<<1))
41
42/* Flags for RF5C_MODE_CTL */
43#define RF5C_MODE_ATA 0x01 /* ATA mode */
44#define RF5C_MODE_LED_ENA 0x02 /* IRQ 12 is LED */
45#define RF5C_MODE_CA21 0x04
46#define RF5C_MODE_CA22 0x08
47#define RF5C_MODE_CA23 0x10
48#define RF5C_MODE_CA24 0x20
49#define RF5C_MODE_CA25 0x40
50#define RF5C_MODE_3STATE_BIT7 0x80
51
52/* Flags for RF5C_PWR_CTL */
53#define RF5C_PWR_VCC_3V 0x01
54#define RF5C_PWR_IREQ_HIGH 0x02
55#define RF5C_PWR_INPACK_ENA 0x04
56#define RF5C_PWR_5V_DET 0x08
57#define RF5C_PWR_TC_SEL 0x10 /* Terminal Count: irq 11 or 15 */
58#define RF5C_PWR_DREQ_LOW 0x20
59#define RF5C_PWR_DREQ_OFF 0x00 /* DREQ steering control */
60#define RF5C_PWR_DREQ_INPACK 0x40
61#define RF5C_PWR_DREQ_SPKR 0x80
62#define RF5C_PWR_DREQ_IOIS16 0xc0
63
64/* Values for RF5C_CHIP_ID */
65#define RF5C_CHIP_RF5C296 0x32
66#define RF5C_CHIP_RF5C396 0xb2
67
68/* Flags for RF5C_MODE_CTL_3 */
69#define RF5C_MCTL3_DISABLE 0x01 /* Disable PCMCIA interface */
70#define RF5C_MCTL3_DMA_ENA 0x02
71
72/* Register definitions for Ricoh PCI-to-CardBus bridges */
73
74/* Extra bits in CB_BRIDGE_CONTROL */
75#define RL5C46X_BCR_3E0_ENA 0x0800
76#define RL5C46X_BCR_3E2_ENA 0x1000
77
78/* Bridge Configuration Register */
79#define RL5C4XX_CONFIG 0x80 /* 16 bit */
80#define RL5C4XX_CONFIG_IO_1_MODE 0x0200
81#define RL5C4XX_CONFIG_IO_0_MODE 0x0100
82#define RL5C4XX_CONFIG_PREFETCH 0x0001
83
84/* Misc Control Register */
85#define RL5C4XX_MISC 0x0082 /* 16 bit */
86#define RL5C4XX_MISC_HW_SUSPEND_ENA 0x0002
87#define RL5C4XX_MISC_VCCEN_POL 0x0100
88#define RL5C4XX_MISC_VPPEN_POL 0x0200
89#define RL5C46X_MISC_SUSPEND 0x0001
90#define RL5C46X_MISC_PWR_SAVE_2 0x0004
91#define RL5C46X_MISC_IFACE_BUSY 0x0008
92#define RL5C46X_MISC_B_LOCK 0x0010
93#define RL5C46X_MISC_A_LOCK 0x0020
94#define RL5C46X_MISC_PCI_LOCK 0x0040
95#define RL5C47X_MISC_IFACE_BUSY 0x0004
96#define RL5C47X_MISC_PCI_INT_MASK 0x0018
97#define RL5C47X_MISC_PCI_INT_DIS 0x0020
98#define RL5C47X_MISC_SUBSYS_WR 0x0040
99#define RL5C47X_MISC_SRIRQ_ENA 0x0080
100#define RL5C47X_MISC_5V_DISABLE 0x0400
101#define RL5C47X_MISC_LED_POL 0x0800
102
103/* 16-bit Interface Control Register */
104#define RL5C4XX_16BIT_CTL 0x0084 /* 16 bit */
105#define RL5C4XX_16CTL_IO_TIMING 0x0100
106#define RL5C4XX_16CTL_MEM_TIMING 0x0200
107#define RL5C46X_16CTL_LEVEL_1 0x0010
108#define RL5C46X_16CTL_LEVEL_2 0x0020
109
110/* 16-bit IO and memory timing registers */
111#define RL5C4XX_16BIT_IO_0 0x0088 /* 16 bit */
112#define RL5C4XX_16BIT_MEM_0 0x008a /* 16 bit */
113#define RL5C4XX_SETUP_MASK 0x0007
114#define RL5C4XX_SETUP_SHIFT 0
115#define RL5C4XX_CMD_MASK 0x01f0
116#define RL5C4XX_CMD_SHIFT 4
117#define RL5C4XX_HOLD_MASK 0x1c00
118#define RL5C4XX_HOLD_SHIFT 10
119#define RL5C4XX_MISC_CONTROL 0x2F /* 8 bit */
120#define RL5C4XX_ZV_ENABLE 0x08
121
122#ifdef __YENTA_H
123
124#define rl_misc(socket) ((socket)->private[0])
125#define rl_ctl(socket) ((socket)->private[1])
126#define rl_io(socket) ((socket)->private[2])
127#define rl_mem(socket) ((socket)->private[3])
128#define rl_config(socket) ((socket)->private[4])
129
130static void ricoh_zoom_video(struct pcmcia_socket *sock, int onoff)
131{
132 u8 reg;
133 struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
134
135 reg = config_readb(socket, RL5C4XX_MISC_CONTROL);
136 if (onoff)
137 /* Zoom zoom, we will all go together, zoom zoom, zoom zoom */
138 reg |= RL5C4XX_ZV_ENABLE;
139 else
140 reg &= ~RL5C4XX_ZV_ENABLE;
141
142 config_writeb(socket, RL5C4XX_MISC_CONTROL, reg);
143}
144
145static void ricoh_set_zv(struct yenta_socket *socket)
146{
147 if(socket->dev->vendor == PCI_VENDOR_ID_RICOH)
148 {
149 switch(socket->dev->device)
150 {
151 /* There may be more .. */
152 case PCI_DEVICE_ID_RICOH_RL5C478:
153 socket->socket.zoom_video = ricoh_zoom_video;
154 break;
155 }
156 }
157}
158
159static void ricoh_save_state(struct yenta_socket *socket)
160{
161 rl_misc(socket) = config_readw(socket, RL5C4XX_MISC);
162 rl_ctl(socket) = config_readw(socket, RL5C4XX_16BIT_CTL);
163 rl_io(socket) = config_readw(socket, RL5C4XX_16BIT_IO_0);
164 rl_mem(socket) = config_readw(socket, RL5C4XX_16BIT_MEM_0);
165 rl_config(socket) = config_readw(socket, RL5C4XX_CONFIG);
166}
167
168static void ricoh_restore_state(struct yenta_socket *socket)
169{
170 config_writew(socket, RL5C4XX_MISC, rl_misc(socket));
171 config_writew(socket, RL5C4XX_16BIT_CTL, rl_ctl(socket));
172 config_writew(socket, RL5C4XX_16BIT_IO_0, rl_io(socket));
173 config_writew(socket, RL5C4XX_16BIT_MEM_0, rl_mem(socket));
174 config_writew(socket, RL5C4XX_CONFIG, rl_config(socket));
175}
176
177
178/*
179 * Magic Ricoh initialization code..
180 */
181static int ricoh_override(struct yenta_socket *socket)
182{
183 u16 config, ctl;
184
185 config = config_readw(socket, RL5C4XX_CONFIG);
186
187 /* Set the default timings, don't trust the original values */
188 ctl = RL5C4XX_16CTL_IO_TIMING | RL5C4XX_16CTL_MEM_TIMING;
189
190 if(socket->dev->device < PCI_DEVICE_ID_RICOH_RL5C475) {
191 ctl |= RL5C46X_16CTL_LEVEL_1 | RL5C46X_16CTL_LEVEL_2;
192 } else {
193 config |= RL5C4XX_CONFIG_PREFETCH;
194 }
195
196 config_writew(socket, RL5C4XX_16BIT_CTL, ctl);
197 config_writew(socket, RL5C4XX_CONFIG, config);
198
199 ricoh_set_zv(socket);
200
201 return 0;
202}
203
204#endif /* CONFIG_CARDBUS */
205
206#endif /* _LINUX_RICOH_H */
1/*
2 * ricoh.h 1.9 1999/10/25 20:03:34
3 *
4 * The contents of this file are subject to the Mozilla Public License
5 * Version 1.1 (the "License"); you may not use this file except in
6 * compliance with the License. You may obtain a copy of the License
7 * at http://www.mozilla.org/MPL/
8 *
9 * Software distributed under the License is distributed on an "AS IS"
10 * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
11 * the License for the specific language governing rights and
12 * limitations under the License.
13 *
14 * The initial developer of the original code is David A. Hinds
15 * <dahinds@users.sourceforge.net>. Portions created by David A. Hinds
16 * are Copyright (C) 1999 David A. Hinds. All Rights Reserved.
17 *
18 * Alternatively, the contents of this file may be used under the
19 * terms of the GNU General Public License version 2 (the "GPL"), in which
20 * case the provisions of the GPL are applicable instead of the
21 * above. If you wish to allow the use of your version of this file
22 * only under the terms of the GPL and not to allow others to use
23 * your version of this file under the MPL, indicate your decision by
24 * deleting the provisions above and replace them with the notice and
25 * other provisions required by the GPL. If you do not delete the
26 * provisions above, a recipient may use your version of this file
27 * under either the MPL or the GPL.
28 */
29
30#ifndef _LINUX_RICOH_H
31#define _LINUX_RICOH_H
32
33
34#define RF5C_MODE_CTL 0x1f /* Mode control */
35#define RF5C_PWR_CTL 0x2f /* Mixed voltage control */
36#define RF5C_CHIP_ID 0x3a /* Chip identification */
37#define RF5C_MODE_CTL_3 0x3b /* Mode control 3 */
38
39/* I/O window address offset */
40#define RF5C_IO_OFF(w) (0x36+((w)<<1))
41
42/* Flags for RF5C_MODE_CTL */
43#define RF5C_MODE_ATA 0x01 /* ATA mode */
44#define RF5C_MODE_LED_ENA 0x02 /* IRQ 12 is LED */
45#define RF5C_MODE_CA21 0x04
46#define RF5C_MODE_CA22 0x08
47#define RF5C_MODE_CA23 0x10
48#define RF5C_MODE_CA24 0x20
49#define RF5C_MODE_CA25 0x40
50#define RF5C_MODE_3STATE_BIT7 0x80
51
52/* Flags for RF5C_PWR_CTL */
53#define RF5C_PWR_VCC_3V 0x01
54#define RF5C_PWR_IREQ_HIGH 0x02
55#define RF5C_PWR_INPACK_ENA 0x04
56#define RF5C_PWR_5V_DET 0x08
57#define RF5C_PWR_TC_SEL 0x10 /* Terminal Count: irq 11 or 15 */
58#define RF5C_PWR_DREQ_LOW 0x20
59#define RF5C_PWR_DREQ_OFF 0x00 /* DREQ steering control */
60#define RF5C_PWR_DREQ_INPACK 0x40
61#define RF5C_PWR_DREQ_SPKR 0x80
62#define RF5C_PWR_DREQ_IOIS16 0xc0
63
64/* Values for RF5C_CHIP_ID */
65#define RF5C_CHIP_RF5C296 0x32
66#define RF5C_CHIP_RF5C396 0xb2
67
68/* Flags for RF5C_MODE_CTL_3 */
69#define RF5C_MCTL3_DISABLE 0x01 /* Disable PCMCIA interface */
70#define RF5C_MCTL3_DMA_ENA 0x02
71
72/* Register definitions for Ricoh PCI-to-CardBus bridges */
73
74/* Extra bits in CB_BRIDGE_CONTROL */
75#define RL5C46X_BCR_3E0_ENA 0x0800
76#define RL5C46X_BCR_3E2_ENA 0x1000
77
78/* Bridge Configuration Register */
79#define RL5C4XX_CONFIG 0x80 /* 16 bit */
80#define RL5C4XX_CONFIG_IO_1_MODE 0x0200
81#define RL5C4XX_CONFIG_IO_0_MODE 0x0100
82#define RL5C4XX_CONFIG_PREFETCH 0x0001
83
84/* Misc Control Register */
85#define RL5C4XX_MISC 0x0082 /* 16 bit */
86#define RL5C4XX_MISC_HW_SUSPEND_ENA 0x0002
87#define RL5C4XX_MISC_VCCEN_POL 0x0100
88#define RL5C4XX_MISC_VPPEN_POL 0x0200
89#define RL5C46X_MISC_SUSPEND 0x0001
90#define RL5C46X_MISC_PWR_SAVE_2 0x0004
91#define RL5C46X_MISC_IFACE_BUSY 0x0008
92#define RL5C46X_MISC_B_LOCK 0x0010
93#define RL5C46X_MISC_A_LOCK 0x0020
94#define RL5C46X_MISC_PCI_LOCK 0x0040
95#define RL5C47X_MISC_IFACE_BUSY 0x0004
96#define RL5C47X_MISC_PCI_INT_MASK 0x0018
97#define RL5C47X_MISC_PCI_INT_DIS 0x0020
98#define RL5C47X_MISC_SUBSYS_WR 0x0040
99#define RL5C47X_MISC_SRIRQ_ENA 0x0080
100#define RL5C47X_MISC_5V_DISABLE 0x0400
101#define RL5C47X_MISC_LED_POL 0x0800
102
103/* 16-bit Interface Control Register */
104#define RL5C4XX_16BIT_CTL 0x0084 /* 16 bit */
105#define RL5C4XX_16CTL_IO_TIMING 0x0100
106#define RL5C4XX_16CTL_MEM_TIMING 0x0200
107#define RL5C46X_16CTL_LEVEL_1 0x0010
108#define RL5C46X_16CTL_LEVEL_2 0x0020
109
110/* 16-bit IO and memory timing registers */
111#define RL5C4XX_16BIT_IO_0 0x0088 /* 16 bit */
112#define RL5C4XX_16BIT_MEM_0 0x008a /* 16 bit */
113#define RL5C4XX_SETUP_MASK 0x0007
114#define RL5C4XX_SETUP_SHIFT 0
115#define RL5C4XX_CMD_MASK 0x01f0
116#define RL5C4XX_CMD_SHIFT 4
117#define RL5C4XX_HOLD_MASK 0x1c00
118#define RL5C4XX_HOLD_SHIFT 10
119#define RL5C4XX_MISC_CONTROL 0x2F /* 8 bit */
120#define RL5C4XX_ZV_ENABLE 0x08
121
122/* Misc Control 3 Register */
123#define RL5C4XX_MISC3 0x00A2 /* 16 bit */
124#define RL5C47X_MISC3_CB_CLKRUN_DIS BIT(1)
125
126#ifdef __YENTA_H
127
128#define rl_misc(socket) ((socket)->private[0])
129#define rl_ctl(socket) ((socket)->private[1])
130#define rl_io(socket) ((socket)->private[2])
131#define rl_mem(socket) ((socket)->private[3])
132#define rl_config(socket) ((socket)->private[4])
133
134static void ricoh_zoom_video(struct pcmcia_socket *sock, int onoff)
135{
136 u8 reg;
137 struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
138
139 reg = config_readb(socket, RL5C4XX_MISC_CONTROL);
140 if (onoff)
141 /* Zoom zoom, we will all go together, zoom zoom, zoom zoom */
142 reg |= RL5C4XX_ZV_ENABLE;
143 else
144 reg &= ~RL5C4XX_ZV_ENABLE;
145
146 config_writeb(socket, RL5C4XX_MISC_CONTROL, reg);
147}
148
149static void ricoh_set_zv(struct yenta_socket *socket)
150{
151 if(socket->dev->vendor == PCI_VENDOR_ID_RICOH)
152 {
153 switch(socket->dev->device)
154 {
155 /* There may be more .. */
156 case PCI_DEVICE_ID_RICOH_RL5C478:
157 socket->socket.zoom_video = ricoh_zoom_video;
158 break;
159 }
160 }
161}
162
163static void ricoh_set_clkrun(struct yenta_socket *socket, bool quiet)
164{
165 u16 misc3;
166
167 /*
168 * RL5C475II likely has this setting, too, however no datasheet
169 * is publicly available for this chip
170 */
171 if (socket->dev->device != PCI_DEVICE_ID_RICOH_RL5C476 &&
172 socket->dev->device != PCI_DEVICE_ID_RICOH_RL5C478)
173 return;
174
175 if (socket->dev->revision < 0x80)
176 return;
177
178 misc3 = config_readw(socket, RL5C4XX_MISC3);
179 if (misc3 & RL5C47X_MISC3_CB_CLKRUN_DIS) {
180 if (!quiet)
181 dev_dbg(&socket->dev->dev,
182 "CLKRUN feature already disabled\n");
183 } else if (disable_clkrun) {
184 if (!quiet)
185 dev_info(&socket->dev->dev,
186 "Disabling CLKRUN feature\n");
187 misc3 |= RL5C47X_MISC3_CB_CLKRUN_DIS;
188 config_writew(socket, RL5C4XX_MISC3, misc3);
189 }
190}
191
192static void ricoh_save_state(struct yenta_socket *socket)
193{
194 rl_misc(socket) = config_readw(socket, RL5C4XX_MISC);
195 rl_ctl(socket) = config_readw(socket, RL5C4XX_16BIT_CTL);
196 rl_io(socket) = config_readw(socket, RL5C4XX_16BIT_IO_0);
197 rl_mem(socket) = config_readw(socket, RL5C4XX_16BIT_MEM_0);
198 rl_config(socket) = config_readw(socket, RL5C4XX_CONFIG);
199}
200
201static void ricoh_restore_state(struct yenta_socket *socket)
202{
203 config_writew(socket, RL5C4XX_MISC, rl_misc(socket));
204 config_writew(socket, RL5C4XX_16BIT_CTL, rl_ctl(socket));
205 config_writew(socket, RL5C4XX_16BIT_IO_0, rl_io(socket));
206 config_writew(socket, RL5C4XX_16BIT_MEM_0, rl_mem(socket));
207 config_writew(socket, RL5C4XX_CONFIG, rl_config(socket));
208 ricoh_set_clkrun(socket, true);
209}
210
211
212/*
213 * Magic Ricoh initialization code..
214 */
215static int ricoh_override(struct yenta_socket *socket)
216{
217 u16 config, ctl;
218
219 config = config_readw(socket, RL5C4XX_CONFIG);
220
221 /* Set the default timings, don't trust the original values */
222 ctl = RL5C4XX_16CTL_IO_TIMING | RL5C4XX_16CTL_MEM_TIMING;
223
224 if(socket->dev->device < PCI_DEVICE_ID_RICOH_RL5C475) {
225 ctl |= RL5C46X_16CTL_LEVEL_1 | RL5C46X_16CTL_LEVEL_2;
226 } else {
227 config |= RL5C4XX_CONFIG_PREFETCH;
228 }
229
230 config_writew(socket, RL5C4XX_16BIT_CTL, ctl);
231 config_writew(socket, RL5C4XX_CONFIG, config);
232
233 ricoh_set_zv(socket);
234 ricoh_set_clkrun(socket, false);
235
236 return 0;
237}
238
239#endif /* CONFIG_CARDBUS */
240
241#endif /* _LINUX_RICOH_H */