Loading...
1#
2# USB Network devices configuration
3#
4comment "Networking support is needed for USB Network Adapter support"
5 depends on USB && !NET
6
7menu "USB Network Adapters"
8 depends on USB && NET
9
10config USB_CATC
11 tristate "USB CATC NetMate-based Ethernet device support (EXPERIMENTAL)"
12 depends on EXPERIMENTAL
13 select CRC32
14 ---help---
15 Say Y if you want to use one of the following 10Mbps USB Ethernet
16 device based on the EL1210A chip. Supported devices are:
17 Belkin F5U011
18 Belkin F5U111
19 CATC NetMate
20 CATC NetMate II
21 smartBridges smartNIC
22
23 This driver makes the adapter appear as a normal Ethernet interface,
24 typically on eth0, if it is the only ethernet device, or perhaps on
25 eth1, if you have a PCI or ISA ethernet card installed.
26
27 To compile this driver as a module, choose M here: the
28 module will be called catc.
29
30config USB_KAWETH
31 tristate "USB KLSI KL5USB101-based ethernet device support"
32 ---help---
33 Say Y here if you want to use one of the following 10Mbps only
34 USB Ethernet adapters based on the KLSI KL5KUSB101B chipset:
35 3Com 3C19250
36 ADS USB-10BT
37 ATEN USB Ethernet
38 ASANTE USB To Ethernet Adapter
39 AOX Endpoints USB Ethernet
40 Correga K.K.
41 D-Link DSB-650C and DU-E10
42 Entrega / Portgear E45
43 I-O DATA USB-ET/T
44 Jaton USB Ethernet Device Adapter
45 Kingston Technology USB Ethernet Adapter
46 Linksys USB10T
47 Mobility USB-Ethernet Adapter
48 NetGear EA-101
49 Peracom Enet and Enet2
50 Portsmith Express Ethernet Adapter
51 Shark Pocket Adapter
52 SMC 2202USB
53 Sony Vaio port extender
54
55 This driver is likely to work with most 10Mbps only USB Ethernet
56 adapters, including some "no brand" devices. It does NOT work on
57 SmartBridges smartNIC or on Belkin F5U111 devices - you should use
58 the CATC NetMate driver for those. If you are not sure which one
59 you need, select both, and the correct one should be selected for
60 you.
61
62 This driver makes the adapter appear as a normal Ethernet interface,
63 typically on eth0, if it is the only ethernet device, or perhaps on
64 eth1, if you have a PCI or ISA ethernet card installed.
65
66 To compile this driver as a module, choose M here: the
67 module will be called kaweth.
68
69config USB_PEGASUS
70 tristate "USB Pegasus/Pegasus-II based ethernet device support"
71 select MII
72 ---help---
73 Say Y here if you know you have Pegasus or Pegasus-II based adapter.
74 If in doubt then look at <file:drivers/net/usb/pegasus.h> for the
75 complete list of supported devices.
76
77 If your particular adapter is not in the list and you are _sure_ it
78 is Pegasus or Pegasus II based then send me
79 <petkan@users.sourceforge.net> vendor and device IDs.
80
81 To compile this driver as a module, choose M here: the
82 module will be called pegasus.
83
84config USB_RTL8150
85 tristate "USB RTL8150 based ethernet device support (EXPERIMENTAL)"
86 depends on EXPERIMENTAL
87 select MII
88 help
89 Say Y here if you have RTL8150 based usb-ethernet adapter.
90 Send me <petkan@users.sourceforge.net> any comments you may have.
91 You can also check for updates at <http://pegasus2.sourceforge.net/>.
92
93 To compile this driver as a module, choose M here: the
94 module will be called rtl8150.
95
96config USB_USBNET
97 tristate "Multi-purpose USB Networking Framework"
98 select MII
99 ---help---
100 This driver supports several kinds of network links over USB,
101 with "minidrivers" built around a common network driver core
102 that supports deep queues for efficient transfers. (This gives
103 better performance with small packets and at high speeds).
104
105 The USB host runs "usbnet", and the other end of the link might be:
106
107 - Another USB host, when using USB "network" or "data transfer"
108 cables. These are often used to network laptops to PCs, like
109 "Laplink" parallel cables or some motherboards. These rely
110 on specialized chips from many suppliers.
111
112 - An intelligent USB gadget, perhaps embedding a Linux system.
113 These include PDAs running Linux (iPaq, Yopy, Zaurus, and
114 others), and devices that interoperate using the standard
115 CDC-Ethernet specification (including many cable modems).
116
117 - Network adapter hardware (like those for 10/100 Ethernet) which
118 uses this driver framework.
119
120 The link will appear with a name like "usb0", when the link is
121 a two-node link, or "eth0" for most CDC-Ethernet devices. Those
122 two-node links are most easily managed with Ethernet Bridging
123 (CONFIG_BRIDGE) instead of routing.
124
125 For more information see <http://www.linux-usb.org/usbnet/>.
126
127 To compile this driver as a module, choose M here: the
128 module will be called usbnet.
129
130config USB_NET_AX8817X
131 tristate "ASIX AX88xxx Based USB 2.0 Ethernet Adapters"
132 depends on USB_USBNET
133 select CRC32
134 default y
135 help
136 This option adds support for ASIX AX88xxx based USB 2.0
137 10/100 Ethernet adapters.
138
139 This driver should work with at least the following devices:
140 * Aten UC210T
141 * ASIX AX88172
142 * Billionton Systems, USB2AR
143 * Buffalo LUA-U2-KTX
144 * Corega FEther USB2-TX
145 * D-Link DUB-E100
146 * Hawking UF200
147 * Linksys USB200M
148 * Netgear FA120
149 * Sitecom LN-029
150 * Intellinet USB 2.0 Ethernet
151 * ST Lab USB 2.0 Ethernet
152 * TrendNet TU2-ET100
153
154 This driver creates an interface named "ethX", where X depends on
155 what other networking devices you have in use.
156
157config USB_NET_CDCETHER
158 tristate "CDC Ethernet support (smart devices such as cable modems)"
159 depends on USB_USBNET
160 default y
161 help
162 This option supports devices conforming to the Communication Device
163 Class (CDC) Ethernet Control Model, a specification that's easy to
164 implement in device firmware. The CDC specifications are available
165 from <http://www.usb.org/>.
166
167 CDC Ethernet is an implementation option for DOCSIS cable modems
168 that support USB connectivity, used for non-Microsoft USB hosts.
169 The Linux-USB CDC Ethernet Gadget driver is an open implementation.
170 This driver should work with at least the following devices:
171
172 * Dell Wireless 5530 HSPA
173 * Ericsson PipeRider (all variants)
174 * Ericsson Mobile Broadband Module (all variants)
175 * Motorola (DM100 and SB4100)
176 * Broadcom Cable Modem (reference design)
177 * Toshiba (PCX1100U and F3507g/F3607gw)
178 * ...
179
180 This driver creates an interface named "ethX", where X depends on
181 what other networking devices you have in use. However, if the
182 IEEE 802 "local assignment" bit is set in the address, a "usbX"
183 name is used instead.
184
185config USB_NET_CDC_EEM
186 tristate "CDC EEM support"
187 depends on USB_USBNET && EXPERIMENTAL
188 help
189 This option supports devices conforming to the Communication Device
190 Class (CDC) Ethernet Emulation Model, a specification that's easy to
191 implement in device firmware. The CDC EEM specifications are available
192 from <http://www.usb.org/>.
193
194 This driver creates an interface named "ethX", where X depends on
195 what other networking devices you have in use. However, if the
196 IEEE 802 "local assignment" bit is set in the address, a "usbX"
197 name is used instead.
198
199config USB_NET_CDC_NCM
200 tristate "CDC NCM support"
201 depends on USB_USBNET
202 default y
203 help
204 This driver provides support for CDC NCM (Network Control Model
205 Device USB Class Specification). The CDC NCM specification is
206 available from <http://www.usb.org/>.
207
208 Say "y" to link the driver statically, or "m" to build a
209 dynamically linked module.
210
211 This driver should work with at least the following devices:
212 * ST-Ericsson M700 LTE FDD/TDD Mobile Broadband Modem (ref. design)
213 * ST-Ericsson M5730 HSPA+ Mobile Broadband Modem (reference design)
214 * ST-Ericsson M570 HSPA+ Mobile Broadband Modem (reference design)
215 * ST-Ericsson M343 HSPA Mobile Broadband Modem (reference design)
216 * Ericsson F5521gw Mobile Broadband Module
217
218config USB_NET_DM9601
219 tristate "Davicom DM9601 based USB 1.1 10/100 ethernet devices"
220 depends on USB_USBNET
221 select CRC32
222 help
223 This option adds support for Davicom DM9601 based USB 1.1
224 10/100 Ethernet adapters.
225
226config USB_NET_SMSC75XX
227 tristate "SMSC LAN75XX based USB 2.0 gigabit ethernet devices"
228 depends on USB_USBNET
229 select CRC32
230 help
231 This option adds support for SMSC LAN95XX based USB 2.0
232 Gigabit Ethernet adapters.
233
234config USB_NET_SMSC95XX
235 tristate "SMSC LAN95XX based USB 2.0 10/100 ethernet devices"
236 depends on USB_USBNET
237 select CRC32
238 help
239 This option adds support for SMSC LAN95XX based USB 2.0
240 10/100 Ethernet adapters.
241
242config USB_NET_GL620A
243 tristate "GeneSys GL620USB-A based cables"
244 depends on USB_USBNET
245 help
246 Choose this option if you're using a host-to-host cable,
247 or PC2PC motherboard, with this chip.
248
249 Note that the half-duplex "GL620USB" is not supported.
250
251config USB_NET_NET1080
252 tristate "NetChip 1080 based cables (Laplink, ...)"
253 default y
254 depends on USB_USBNET
255 help
256 Choose this option if you're using a host-to-host cable based
257 on this design: one NetChip 1080 chip and supporting logic,
258 optionally with LEDs that indicate traffic
259
260config USB_NET_PLUSB
261 tristate "Prolific PL-2301/2302/25A1 based cables"
262 # if the handshake/init/reset problems, from original 'plusb',
263 # are ever resolved ... then remove "experimental"
264 depends on USB_USBNET && EXPERIMENTAL
265 help
266 Choose this option if you're using a host-to-host cable
267 with one of these chips.
268
269config USB_NET_MCS7830
270 tristate "MosChip MCS7830 based Ethernet adapters"
271 depends on USB_USBNET
272 help
273 Choose this option if you're using a 10/100 Ethernet USB2
274 adapter based on the MosChip 7830 controller. This includes
275 adapters marketed under the DeLOCK brand.
276
277config USB_NET_RNDIS_HOST
278 tristate "Host for RNDIS and ActiveSync devices (EXPERIMENTAL)"
279 depends on USB_USBNET && EXPERIMENTAL
280 select USB_NET_CDCETHER
281 help
282 This option enables hosting "Remote NDIS" USB networking links,
283 as encouraged by Microsoft (instead of CDC Ethernet!) for use in
284 various devices that may only support this protocol. A variant
285 of this protocol (with even less public documentation) seems to
286 be at the root of Microsoft's "ActiveSync" too.
287
288 Avoid using this protocol unless you have no better options.
289 The protocol specification is incomplete, and is controlled by
290 (and for) Microsoft; it isn't an "Open" ecosystem or market.
291
292config USB_NET_CDC_SUBSET
293 tristate "Simple USB Network Links (CDC Ethernet subset)"
294 depends on USB_USBNET
295 default y
296 help
297 This driver module supports USB network devices that can work
298 without any device-specific information. Select it if you have
299 one of these drivers.
300
301 Note that while many USB host-to-host cables can work in this mode,
302 that may mean not being able to talk to Win32 systems or more
303 commonly not being able to handle certain events (like replugging
304 the host on the other end) very well. Also, these devices will
305 not generally have permanently assigned Ethernet addresses.
306
307config USB_ALI_M5632
308 boolean "ALi M5632 based 'USB 2.0 Data Link' cables"
309 depends on USB_NET_CDC_SUBSET
310 help
311 Choose this option if you're using a host-to-host cable
312 based on this design, which supports USB 2.0 high speed.
313
314config USB_AN2720
315 boolean "AnchorChips 2720 based cables (Xircom PGUNET, ...)"
316 depends on USB_NET_CDC_SUBSET
317 help
318 Choose this option if you're using a host-to-host cable
319 based on this design. Note that AnchorChips is now a
320 Cypress brand.
321
322config USB_BELKIN
323 boolean "eTEK based host-to-host cables (Advance, Belkin, ...)"
324 depends on USB_NET_CDC_SUBSET
325 default y
326 help
327 Choose this option if you're using a host-to-host cable
328 based on this design: two NetChip 2890 chips and an Atmel
329 microcontroller, with LEDs that indicate traffic.
330
331config USB_ARMLINUX
332 boolean "Embedded ARM Linux links (iPaq, ...)"
333 depends on USB_NET_CDC_SUBSET
334 default y
335 help
336 Choose this option to support the "usb-eth" networking driver
337 used by most of the ARM Linux community with device controllers
338 such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities
339 in some PXA versions of the "blob" boot loader.
340
341 Linux-based "Gumstix" PXA-25x based systems use this protocol
342 to talk with other Linux systems.
343
344 Although the ROMs shipped with Sharp Zaurus products use a
345 different link level framing protocol, you can have them use
346 this simpler protocol by installing a different kernel.
347
348config USB_EPSON2888
349 boolean "Epson 2888 based firmware (DEVELOPMENT)"
350 depends on USB_NET_CDC_SUBSET
351 help
352 Choose this option to support the usb networking links used
353 by some sample firmware from Epson.
354
355config USB_KC2190
356 boolean "KT Technology KC2190 based cables (InstaNet)"
357 depends on USB_NET_CDC_SUBSET && EXPERIMENTAL
358 help
359 Choose this option if you're using a host-to-host cable
360 with one of these chips.
361
362config USB_NET_ZAURUS
363 tristate "Sharp Zaurus (stock ROMs) and compatible"
364 depends on USB_USBNET
365 select USB_NET_CDCETHER
366 select CRC32
367 default y
368 help
369 Choose this option to support the usb networking links used by
370 Zaurus models like the SL-5000D, SL-5500, SL-5600, A-300, B-500.
371 This also supports some related device firmware, as used in some
372 PDAs from Olympus and some cell phones from Motorola.
373
374 If you install an alternate image, such as the Linux 2.6 based
375 versions of OpenZaurus, you should no longer need to support this
376 protocol. Only the "eth-fd" or "net_fd" drivers in these devices
377 really need this non-conformant variant of CDC Ethernet (or in
378 some cases CDC MDLM) protocol, not "g_ether".
379
380config USB_NET_CX82310_ETH
381 tristate "Conexant CX82310 USB ethernet port"
382 depends on USB_USBNET
383 help
384 Choose this option if you're using a Conexant CX82310-based ADSL
385 router with USB ethernet port. This driver is for routers only,
386 it will not work with ADSL modems (use cxacru driver instead).
387
388config USB_NET_KALMIA
389 tristate "Samsung Kalmia based LTE USB modem"
390 depends on USB_USBNET
391 help
392 Choose this option if you have a Samsung Kalmia based USB modem
393 as Samsung GT-B3730.
394
395 To compile this driver as a module, choose M here: the
396 module will be called kalmia.
397
398config USB_HSO
399 tristate "Option USB High Speed Mobile Devices"
400 depends on USB && RFKILL
401 default n
402 help
403 Choose this option if you have an Option HSDPA/HSUPA card.
404 These cards support downlink speeds of 7.2Mbps or greater.
405
406 To compile this driver as a module, choose M here: the
407 module will be called hso.
408
409config USB_NET_INT51X1
410 tristate "Intellon PLC based usb adapter"
411 depends on USB_USBNET
412 help
413 Choose this option if you're using a 14Mb USB-based PLC
414 (Powerline Communications) solution with an Intellon
415 INT51x1/INT5200 chip, like the "devolo dLan duo".
416
417config USB_CDC_PHONET
418 tristate "CDC Phonet support"
419 depends on PHONET
420 help
421 Choose this option to support the Phonet interface to a Nokia
422 cellular modem, as found on most Nokia handsets with the
423 "PC suite" USB profile.
424
425config USB_IPHETH
426 tristate "Apple iPhone USB Ethernet driver"
427 default n
428 ---help---
429 Module used to share Internet connection (tethering) from your
430 iPhone (Original, 3G and 3GS) to your system.
431 Note that you need userspace libraries and programs that are needed
432 to pair your device with your system and that understand the iPhone
433 protocol.
434
435 For more information: http://giagio.com/wiki/moin.cgi/iPhoneEthernetDriver
436
437config USB_SIERRA_NET
438 tristate "USB-to-WWAN Driver for Sierra Wireless modems"
439 depends on USB_USBNET
440 help
441 Choose this option if you have a Sierra Wireless USB-to-WWAN device.
442
443 To compile this driver as a module, choose M here: the
444 module will be called sierra_net.
445
446config USB_VL600
447 tristate "LG VL600 modem dongle"
448 depends on USB_NET_CDCETHER
449 select USB_ACM
450 help
451 Select this if you want to use an LG Electronics 4G/LTE usb modem
452 called VL600. This driver only handles the ethernet
453 interface exposed by the modem firmware. To establish a connection
454 you will first need a userspace program that sends the right
455 command to the modem through its CDC ACM port, and most
456 likely also a DHCP client. See this thread about using the
457 4G modem from Verizon:
458
459 http://ubuntuforums.org/showpost.php?p=10589647&postcount=17
460
461endmenu
1#
2# USB Network devices configuration
3#
4comment "Host-side USB support is needed for USB Network Adapter support"
5 depends on !USB && NET
6
7menuconfig USB_NET_DRIVERS
8 tristate "USB Network Adapters"
9 default USB if USB
10 depends on USB && NET
11
12if USB_NET_DRIVERS
13
14config USB_CATC
15 tristate "USB CATC NetMate-based Ethernet device support"
16 select CRC32
17 ---help---
18 Say Y if you want to use one of the following 10Mbps USB Ethernet
19 device based on the EL1210A chip. Supported devices are:
20 Belkin F5U011
21 Belkin F5U111
22 CATC NetMate
23 CATC NetMate II
24 smartBridges smartNIC
25
26 This driver makes the adapter appear as a normal Ethernet interface,
27 typically on eth0, if it is the only ethernet device, or perhaps on
28 eth1, if you have a PCI or ISA ethernet card installed.
29
30 To compile this driver as a module, choose M here: the
31 module will be called catc.
32
33config USB_KAWETH
34 tristate "USB KLSI KL5USB101-based ethernet device support"
35 ---help---
36 Say Y here if you want to use one of the following 10Mbps only
37 USB Ethernet adapters based on the KLSI KL5KUSB101B chipset:
38 3Com 3C19250
39 ADS USB-10BT
40 ATEN USB Ethernet
41 ASANTE USB To Ethernet Adapter
42 AOX Endpoints USB Ethernet
43 Correga K.K.
44 D-Link DSB-650C and DU-E10
45 Entrega / Portgear E45
46 I-O DATA USB-ET/T
47 Jaton USB Ethernet Device Adapter
48 Kingston Technology USB Ethernet Adapter
49 Linksys USB10T
50 Mobility USB-Ethernet Adapter
51 NetGear EA-101
52 Peracom Enet and Enet2
53 Portsmith Express Ethernet Adapter
54 Shark Pocket Adapter
55 SMC 2202USB
56 Sony Vaio port extender
57
58 This driver is likely to work with most 10Mbps only USB Ethernet
59 adapters, including some "no brand" devices. It does NOT work on
60 SmartBridges smartNIC or on Belkin F5U111 devices - you should use
61 the CATC NetMate driver for those. If you are not sure which one
62 you need, select both, and the correct one should be selected for
63 you.
64
65 This driver makes the adapter appear as a normal Ethernet interface,
66 typically on eth0, if it is the only ethernet device, or perhaps on
67 eth1, if you have a PCI or ISA ethernet card installed.
68
69 To compile this driver as a module, choose M here: the
70 module will be called kaweth.
71
72config USB_PEGASUS
73 tristate "USB Pegasus/Pegasus-II based ethernet device support"
74 select MII
75 ---help---
76 Say Y here if you know you have Pegasus or Pegasus-II based adapter.
77 If in doubt then look at <file:drivers/net/usb/pegasus.h> for the
78 complete list of supported devices.
79
80 If your particular adapter is not in the list and you are _sure_ it
81 is Pegasus or Pegasus II based then send me
82 <petkan@users.sourceforge.net> vendor and device IDs.
83
84 To compile this driver as a module, choose M here: the
85 module will be called pegasus.
86
87config USB_RTL8150
88 tristate "USB RTL8150 based ethernet device support"
89 select MII
90 help
91 Say Y here if you have RTL8150 based usb-ethernet adapter.
92 Send me <petkan@users.sourceforge.net> any comments you may have.
93 You can also check for updates at <http://pegasus2.sourceforge.net/>.
94
95 To compile this driver as a module, choose M here: the
96 module will be called rtl8150.
97
98config USB_RTL8152
99 tristate "Realtek RTL8152/RTL8153 Based USB Ethernet Adapters"
100 select MII
101 help
102 This option adds support for Realtek RTL8152 based USB 2.0
103 10/100 Ethernet adapters and RTL8153 based USB 3.0 10/100/1000
104 Ethernet adapters.
105
106 To compile this driver as a module, choose M here: the
107 module will be called r8152.
108
109config USB_LAN78XX
110 tristate "Microchip LAN78XX Based USB Ethernet Adapters"
111 select MII
112 select PHYLIB
113 select MICROCHIP_PHY
114 help
115 This option adds support for Microchip LAN78XX based USB 2
116 & USB 3 10/100/1000 Ethernet adapters.
117
118 To compile this driver as a module, choose M here: the
119 module will be called lan78xx.
120
121config USB_USBNET
122 tristate "Multi-purpose USB Networking Framework"
123 select MII
124 ---help---
125 This driver supports several kinds of network links over USB,
126 with "minidrivers" built around a common network driver core
127 that supports deep queues for efficient transfers. (This gives
128 better performance with small packets and at high speeds).
129
130 The USB host runs "usbnet", and the other end of the link might be:
131
132 - Another USB host, when using USB "network" or "data transfer"
133 cables. These are often used to network laptops to PCs, like
134 "Laplink" parallel cables or some motherboards. These rely
135 on specialized chips from many suppliers.
136
137 - An intelligent USB gadget, perhaps embedding a Linux system.
138 These include PDAs running Linux (iPaq, Yopy, Zaurus, and
139 others), and devices that interoperate using the standard
140 CDC-Ethernet specification (including many cable modems).
141
142 - Network adapter hardware (like those for 10/100 Ethernet) which
143 uses this driver framework.
144
145 The link will appear with a name like "usb0", when the link is
146 a two-node link, or "eth0" for most CDC-Ethernet devices. Those
147 two-node links are most easily managed with Ethernet Bridging
148 (CONFIG_BRIDGE) instead of routing.
149
150 For more information see <http://www.linux-usb.org/usbnet/>.
151
152 To compile this driver as a module, choose M here: the
153 module will be called usbnet.
154
155config USB_NET_AX8817X
156 tristate "ASIX AX88xxx Based USB 2.0 Ethernet Adapters"
157 depends on USB_USBNET
158 select CRC32
159 select PHYLIB
160 default y
161 help
162 This option adds support for ASIX AX88xxx based USB 2.0
163 10/100 Ethernet adapters.
164
165 This driver should work with at least the following devices:
166 * Aten UC210T
167 * ASIX AX88172
168 * Billionton Systems, USB2AR
169 * Billionton Systems, GUSB2AM-1G-B
170 * Buffalo LUA-U2-KTX
171 * Corega FEther USB2-TX
172 * D-Link DUB-E100
173 * Hawking UF200
174 * Linksys USB200M
175 * Netgear FA120
176 * Sitecom LN-029
177 * Sitecom LN-028
178 * Intellinet USB 2.0 Ethernet
179 * ST Lab USB 2.0 Ethernet
180 * TrendNet TU2-ET100
181
182 This driver creates an interface named "ethX", where X depends on
183 what other networking devices you have in use.
184
185config USB_NET_AX88179_178A
186 tristate "ASIX AX88179/178A USB 3.0/2.0 to Gigabit Ethernet"
187 depends on USB_USBNET
188 select CRC32
189 select PHYLIB
190 default y
191 help
192 This option adds support for ASIX AX88179 based USB 3.0/2.0
193 to Gigabit Ethernet adapters.
194
195 This driver should work with at least the following devices:
196 * ASIX AX88179
197 * ASIX AX88178A
198 * Sitcomm LN-032
199
200 This driver creates an interface named "ethX", where X depends on
201 what other networking devices you have in use.
202
203config USB_NET_CDCETHER
204 tristate "CDC Ethernet support (smart devices such as cable modems)"
205 depends on USB_USBNET
206 default y
207 help
208 This option supports devices conforming to the Communication Device
209 Class (CDC) Ethernet Control Model, a specification that's easy to
210 implement in device firmware. The CDC specifications are available
211 from <http://www.usb.org/>.
212
213 CDC Ethernet is an implementation option for DOCSIS cable modems
214 that support USB connectivity, used for non-Microsoft USB hosts.
215 The Linux-USB CDC Ethernet Gadget driver is an open implementation.
216 This driver should work with at least the following devices:
217
218 * Dell Wireless 5530 HSPA
219 * Ericsson PipeRider (all variants)
220 * Ericsson Mobile Broadband Module (all variants)
221 * Motorola (DM100 and SB4100)
222 * Broadcom Cable Modem (reference design)
223 * Toshiba (PCX1100U and F3507g/F3607gw)
224 * ...
225
226 This driver creates an interface named "ethX", where X depends on
227 what other networking devices you have in use. However, if the
228 IEEE 802 "local assignment" bit is set in the address, a "usbX"
229 name is used instead.
230
231config USB_NET_CDC_EEM
232 tristate "CDC EEM support"
233 depends on USB_USBNET
234 help
235 This option supports devices conforming to the Communication Device
236 Class (CDC) Ethernet Emulation Model, a specification that's easy to
237 implement in device firmware. The CDC EEM specifications are available
238 from <http://www.usb.org/>.
239
240 This driver creates an interface named "ethX", where X depends on
241 what other networking devices you have in use. However, if the
242 IEEE 802 "local assignment" bit is set in the address, a "usbX"
243 name is used instead.
244
245config USB_NET_CDC_NCM
246 tristate "CDC NCM support"
247 depends on USB_USBNET
248 default y
249 help
250 This driver provides support for CDC NCM (Network Control Model
251 Device USB Class Specification). The CDC NCM specification is
252 available from <http://www.usb.org/>.
253
254 Say "y" to link the driver statically, or "m" to build a
255 dynamically linked module.
256
257 This driver should work with at least the following devices:
258 * ST-Ericsson M700 LTE FDD/TDD Mobile Broadband Modem (ref. design)
259 * ST-Ericsson M5730 HSPA+ Mobile Broadband Modem (reference design)
260 * ST-Ericsson M570 HSPA+ Mobile Broadband Modem (reference design)
261 * ST-Ericsson M343 HSPA Mobile Broadband Modem (reference design)
262 * Ericsson F5521gw Mobile Broadband Module
263
264config USB_NET_HUAWEI_CDC_NCM
265 tristate "Huawei NCM embedded AT channel support"
266 depends on USB_USBNET
267 select USB_WDM
268 select USB_NET_CDC_NCM
269 help
270 This driver supports huawei-style NCM devices, that use NCM as a
271 transport for other protocols, usually an embedded AT channel.
272 Good examples are:
273 * Huawei E3131
274 * Huawei E3251
275
276 To compile this driver as a module, choose M here: the module will be
277 called huawei_cdc_ncm.ko.
278
279config USB_NET_CDC_MBIM
280 tristate "CDC MBIM support"
281 depends on USB_USBNET
282 select USB_WDM
283 select USB_NET_CDC_NCM
284 help
285 This driver provides support for CDC MBIM (Mobile Broadband
286 Interface Model) devices. The CDC MBIM specification is
287 available from <http://www.usb.org/>.
288
289 MBIM devices require configuration using the management
290 protocol defined by the MBIM specification. This driver
291 provides unfiltered access to the MBIM control channel
292 through the associated /dev/cdc-wdmx character device.
293
294 To compile this driver as a module, choose M here: the
295 module will be called cdc_mbim.
296
297config USB_NET_DM9601
298 tristate "Davicom DM96xx based USB 10/100 ethernet devices"
299 depends on USB_USBNET
300 select CRC32
301 help
302 This option adds support for Davicom DM9601/DM9620/DM9621A
303 based USB 10/100 Ethernet adapters.
304
305config USB_NET_SR9700
306 tristate "CoreChip-sz SR9700 based USB 1.1 10/100 ethernet devices"
307 depends on USB_USBNET
308 select CRC32
309 help
310 This option adds support for CoreChip-sz SR9700 based USB 1.1
311 10/100 Ethernet adapters.
312
313config USB_NET_SR9800
314 tristate "CoreChip-sz SR9800 based USB 2.0 10/100 ethernet devices"
315 depends on USB_USBNET
316 select CRC32
317 ---help---
318 Say Y if you want to use one of the following 100Mbps USB Ethernet
319 device based on the CoreChip-sz SR9800 chip.
320
321 This driver makes the adapter appear as a normal Ethernet interface,
322 typically on eth0, if it is the only ethernet device, or perhaps on
323 eth1, if you have a PCI or ISA ethernet card installed.
324
325 To compile this driver as a module, choose M here: the
326 module will be called sr9800.
327
328config USB_NET_SMSC75XX
329 tristate "SMSC LAN75XX based USB 2.0 gigabit ethernet devices"
330 depends on USB_USBNET
331 select BITREVERSE
332 select CRC16
333 select CRC32
334 help
335 This option adds support for SMSC LAN75XX based USB 2.0
336 Gigabit Ethernet adapters.
337
338config USB_NET_SMSC95XX
339 tristate "SMSC LAN95XX based USB 2.0 10/100 ethernet devices"
340 depends on USB_USBNET
341 select BITREVERSE
342 select CRC16
343 select CRC32
344 help
345 This option adds support for SMSC LAN95XX based USB 2.0
346 10/100 Ethernet adapters.
347
348config USB_NET_GL620A
349 tristate "GeneSys GL620USB-A based cables"
350 depends on USB_USBNET
351 help
352 Choose this option if you're using a host-to-host cable,
353 or PC2PC motherboard, with this chip.
354
355 Note that the half-duplex "GL620USB" is not supported.
356
357config USB_NET_NET1080
358 tristate "NetChip 1080 based cables (Laplink, ...)"
359 default y
360 depends on USB_USBNET
361 help
362 Choose this option if you're using a host-to-host cable based
363 on this design: one NetChip 1080 chip and supporting logic,
364 optionally with LEDs that indicate traffic
365
366config USB_NET_PLUSB
367 tristate "Prolific PL-2301/2302/25A1 based cables"
368 # if the handshake/init/reset problems, from original 'plusb',
369 # are ever resolved ... then remove "experimental"
370 depends on USB_USBNET
371 help
372 Choose this option if you're using a host-to-host cable
373 with one of these chips.
374
375config USB_NET_MCS7830
376 tristate "MosChip MCS7830 based Ethernet adapters"
377 depends on USB_USBNET
378 help
379 Choose this option if you're using a 10/100 Ethernet USB2
380 adapter based on the MosChip 7830 controller. This includes
381 adapters marketed under the DeLOCK brand.
382
383config USB_NET_RNDIS_HOST
384 tristate "Host for RNDIS and ActiveSync devices"
385 depends on USB_USBNET
386 select USB_NET_CDCETHER
387 help
388 This option enables hosting "Remote NDIS" USB networking links,
389 as encouraged by Microsoft (instead of CDC Ethernet!) for use in
390 various devices that may only support this protocol. A variant
391 of this protocol (with even less public documentation) seems to
392 be at the root of Microsoft's "ActiveSync" too.
393
394 Avoid using this protocol unless you have no better options.
395 The protocol specification is incomplete, and is controlled by
396 (and for) Microsoft; it isn't an "Open" ecosystem or market.
397
398config USB_NET_CDC_SUBSET_ENABLE
399 tristate
400 depends on USB_NET_CDC_SUBSET
401
402config USB_NET_CDC_SUBSET
403 tristate "Simple USB Network Links (CDC Ethernet subset)"
404 depends on USB_USBNET
405 default y
406 help
407 This driver module supports USB network devices that can work
408 without any device-specific information. Select it if you have
409 one of these drivers.
410
411 Note that while many USB host-to-host cables can work in this mode,
412 that may mean not being able to talk to Win32 systems or more
413 commonly not being able to handle certain events (like replugging
414 the host on the other end) very well. Also, these devices will
415 not generally have permanently assigned Ethernet addresses.
416
417config USB_ALI_M5632
418 bool "ALi M5632 based 'USB 2.0 Data Link' cables"
419 depends on USB_NET_CDC_SUBSET
420 select USB_NET_CDC_SUBSET_ENABLE
421 help
422 Choose this option if you're using a host-to-host cable
423 based on this design, which supports USB 2.0 high speed.
424
425config USB_AN2720
426 bool "AnchorChips 2720 based cables (Xircom PGUNET, ...)"
427 depends on USB_NET_CDC_SUBSET
428 select USB_NET_CDC_SUBSET_ENABLE
429 help
430 Choose this option if you're using a host-to-host cable
431 based on this design. Note that AnchorChips is now a
432 Cypress brand.
433
434config USB_BELKIN
435 bool "eTEK based host-to-host cables (Advance, Belkin, ...)"
436 depends on USB_NET_CDC_SUBSET
437 select USB_NET_CDC_SUBSET_ENABLE
438 default y
439 help
440 Choose this option if you're using a host-to-host cable
441 based on this design: two NetChip 2890 chips and an Atmel
442 microcontroller, with LEDs that indicate traffic.
443
444config USB_ARMLINUX
445 bool "Embedded ARM Linux links (iPaq, ...)"
446 depends on USB_NET_CDC_SUBSET
447 select USB_NET_CDC_SUBSET_ENABLE
448 default y
449 help
450 Choose this option to support the "usb-eth" networking driver
451 used by most of the ARM Linux community with device controllers
452 such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities
453 in some PXA versions of the "blob" boot loader.
454
455 Linux-based "Gumstix" PXA-25x based systems use this protocol
456 to talk with other Linux systems.
457
458 Although the ROMs shipped with Sharp Zaurus products use a
459 different link level framing protocol, you can have them use
460 this simpler protocol by installing a different kernel.
461
462config USB_EPSON2888
463 bool "Epson 2888 based firmware (DEVELOPMENT)"
464 depends on USB_NET_CDC_SUBSET
465 select USB_NET_CDC_SUBSET_ENABLE
466 help
467 Choose this option to support the usb networking links used
468 by some sample firmware from Epson.
469
470config USB_KC2190
471 bool "KT Technology KC2190 based cables (InstaNet)"
472 depends on USB_NET_CDC_SUBSET
473 select USB_NET_CDC_SUBSET_ENABLE
474 help
475 Choose this option if you're using a host-to-host cable
476 with one of these chips.
477
478config USB_NET_ZAURUS
479 tristate "Sharp Zaurus (stock ROMs) and compatible"
480 depends on USB_USBNET
481 select USB_NET_CDCETHER
482 select CRC32
483 default y
484 help
485 Choose this option to support the usb networking links used by
486 Zaurus models like the SL-5000D, SL-5500, SL-5600, A-300, B-500.
487 This also supports some related device firmware, as used in some
488 PDAs from Olympus and some cell phones from Motorola.
489
490 If you install an alternate image, such as the Linux 2.6 based
491 versions of OpenZaurus, you should no longer need to support this
492 protocol. Only the "eth-fd" or "net_fd" drivers in these devices
493 really need this non-conformant variant of CDC Ethernet (or in
494 some cases CDC MDLM) protocol, not "g_ether".
495
496config USB_NET_CX82310_ETH
497 tristate "Conexant CX82310 USB ethernet port"
498 depends on USB_USBNET
499 help
500 Choose this option if you're using a Conexant CX82310-based ADSL
501 router with USB ethernet port. This driver is for routers only,
502 it will not work with ADSL modems (use cxacru driver instead).
503
504config USB_NET_KALMIA
505 tristate "Samsung Kalmia based LTE USB modem"
506 depends on USB_USBNET
507 help
508 Choose this option if you have a Samsung Kalmia based USB modem
509 as Samsung GT-B3730.
510
511 To compile this driver as a module, choose M here: the
512 module will be called kalmia.
513
514config USB_NET_QMI_WWAN
515 tristate "QMI WWAN driver for Qualcomm MSM based 3G and LTE modems"
516 depends on USB_USBNET
517 select USB_WDM
518 help
519 Support WWAN LTE/3G devices based on Qualcomm Mobile Data Modem
520 (MDM) chipsets. Examples of such devices are
521 * Huawei E392/E398
522
523 This driver will only drive the ethernet part of the chips.
524 The devices require additional configuration to be usable.
525 Multiple management interfaces with linux drivers are
526 available:
527
528 * option: AT commands on /dev/ttyUSBx
529 * cdc-wdm: Qualcomm MSM Interface (QMI) protocol on /dev/cdc-wdmx
530
531 A modem manager with support for QMI is recommended.
532
533 To compile this driver as a module, choose M here: the
534 module will be called qmi_wwan.
535
536config USB_HSO
537 tristate "Option USB High Speed Mobile Devices"
538 depends on USB && RFKILL && TTY
539 default n
540 help
541 Choose this option if you have an Option HSDPA/HSUPA card.
542 These cards support downlink speeds of 7.2Mbps or greater.
543
544 To compile this driver as a module, choose M here: the
545 module will be called hso.
546
547config USB_NET_INT51X1
548 tristate "Intellon PLC based usb adapter"
549 depends on USB_USBNET
550 help
551 Choose this option if you're using a 14Mb USB-based PLC
552 (Powerline Communications) solution with an Intellon
553 INT51x1/INT5200 chip, like the "devolo dLan duo".
554
555config USB_CDC_PHONET
556 tristate "CDC Phonet support"
557 depends on PHONET && USB_USBNET
558 help
559 Choose this option to support the Phonet interface to a Nokia
560 cellular modem, as found on most Nokia handsets with the
561 "PC suite" USB profile.
562
563config USB_IPHETH
564 tristate "Apple iPhone USB Ethernet driver"
565 default n
566 ---help---
567 Module used to share Internet connection (tethering) from your
568 iPhone (Original, 3G and 3GS) to your system.
569 Note that you need userspace libraries and programs that are needed
570 to pair your device with your system and that understand the iPhone
571 protocol.
572
573 For more information: http://giagio.com/wiki/moin.cgi/iPhoneEthernetDriver
574
575config USB_SIERRA_NET
576 tristate "USB-to-WWAN Driver for Sierra Wireless modems"
577 depends on USB_USBNET
578 help
579 Choose this option if you have a Sierra Wireless USB-to-WWAN device.
580
581 To compile this driver as a module, choose M here: the
582 module will be called sierra_net.
583
584config USB_VL600
585 tristate "LG VL600 modem dongle"
586 depends on USB_NET_CDCETHER && TTY
587 select USB_ACM
588 help
589 Select this if you want to use an LG Electronics 4G/LTE usb modem
590 called VL600. This driver only handles the ethernet
591 interface exposed by the modem firmware. To establish a connection
592 you will first need a userspace program that sends the right
593 command to the modem through its CDC ACM port, and most
594 likely also a DHCP client. See this thread about using the
595 4G modem from Verizon:
596
597 http://ubuntuforums.org/showpost.php?p=10589647&postcount=17
598
599config USB_NET_CH9200
600 tristate "QingHeng CH9200 USB ethernet support"
601 depends on USB_USBNET
602 select MII
603 help
604 Choose this option if you have a USB ethernet adapter with a QinHeng
605 CH9200 chipset.
606
607 To compile this driver as a module, choose M here: the
608 module will be called ch9200.
609
610endif # USB_NET_DRIVERS