Loading...
1/*
2 * su.c: Small serial driver for keyboard/mouse interface on sparc32/PCI
3 *
4 * Copyright (C) 1997 Eddie C. Dost (ecd@skynet.be)
5 * Copyright (C) 1998-1999 Pete Zaitcev (zaitcev@yahoo.com)
6 *
7 * This is mainly a variation of 8250.c, credits go to authors mentioned
8 * therein. In fact this driver should be merged into the generic 8250.c
9 * infrastructure perhaps using a 8250_sparc.c module.
10 *
11 * Fixed to use tty_get_baud_rate().
12 * Theodore Ts'o <tytso@mit.edu>, 2001-Oct-12
13 *
14 * Converted to new 2.5.x UART layer.
15 * David S. Miller (davem@davemloft.net), 2002-Jul-29
16 */
17
18#include <linux/module.h>
19#include <linux/kernel.h>
20#include <linux/spinlock.h>
21#include <linux/errno.h>
22#include <linux/tty.h>
23#include <linux/tty_flip.h>
24#include <linux/major.h>
25#include <linux/string.h>
26#include <linux/ptrace.h>
27#include <linux/ioport.h>
28#include <linux/circ_buf.h>
29#include <linux/serial.h>
30#include <linux/sysrq.h>
31#include <linux/console.h>
32#include <linux/slab.h>
33#ifdef CONFIG_SERIO
34#include <linux/serio.h>
35#endif
36#include <linux/serial_reg.h>
37#include <linux/init.h>
38#include <linux/delay.h>
39#include <linux/of_device.h>
40
41#include <asm/io.h>
42#include <asm/irq.h>
43#include <asm/prom.h>
44
45#if defined(CONFIG_SERIAL_SUNSU_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
46#define SUPPORT_SYSRQ
47#endif
48
49#include <linux/serial_core.h>
50
51#include "suncore.h"
52
53/* We are on a NS PC87303 clocked with 24.0 MHz, which results
54 * in a UART clock of 1.8462 MHz.
55 */
56#define SU_BASE_BAUD (1846200 / 16)
57
58enum su_type { SU_PORT_NONE, SU_PORT_MS, SU_PORT_KBD, SU_PORT_PORT };
59static char *su_typev[] = { "su(???)", "su(mouse)", "su(kbd)", "su(serial)" };
60
61/*
62 * Here we define the default xmit fifo size used for each type of UART.
63 */
64static const struct serial_uart_config uart_config[PORT_MAX_8250+1] = {
65 { "unknown", 1, 0 },
66 { "8250", 1, 0 },
67 { "16450", 1, 0 },
68 { "16550", 1, 0 },
69 { "16550A", 16, UART_CLEAR_FIFO | UART_USE_FIFO },
70 { "Cirrus", 1, 0 },
71 { "ST16650", 1, UART_CLEAR_FIFO | UART_STARTECH },
72 { "ST16650V2", 32, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
73 { "TI16750", 64, UART_CLEAR_FIFO | UART_USE_FIFO },
74 { "Startech", 1, 0 },
75 { "16C950/954", 128, UART_CLEAR_FIFO | UART_USE_FIFO },
76 { "ST16654", 64, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
77 { "XR16850", 128, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
78 { "RSA", 2048, UART_CLEAR_FIFO | UART_USE_FIFO }
79};
80
81struct uart_sunsu_port {
82 struct uart_port port;
83 unsigned char acr;
84 unsigned char ier;
85 unsigned short rev;
86 unsigned char lcr;
87 unsigned int lsr_break_flag;
88 unsigned int cflag;
89
90 /* Probing information. */
91 enum su_type su_type;
92 unsigned int type_probed; /* XXX Stupid */
93 unsigned long reg_size;
94
95#ifdef CONFIG_SERIO
96 struct serio serio;
97 int serio_open;
98#endif
99};
100
101static unsigned int serial_in(struct uart_sunsu_port *up, int offset)
102{
103 offset <<= up->port.regshift;
104
105 switch (up->port.iotype) {
106 case UPIO_HUB6:
107 outb(up->port.hub6 - 1 + offset, up->port.iobase);
108 return inb(up->port.iobase + 1);
109
110 case UPIO_MEM:
111 return readb(up->port.membase + offset);
112
113 default:
114 return inb(up->port.iobase + offset);
115 }
116}
117
118static void serial_out(struct uart_sunsu_port *up, int offset, int value)
119{
120#ifndef CONFIG_SPARC64
121 /*
122 * MrCoffee has weird schematics: IRQ4 & P10(?) pins of SuperIO are
123 * connected with a gate then go to SlavIO. When IRQ4 goes tristated
124 * gate outputs a logical one. Since we use level triggered interrupts
125 * we have lockup and watchdog reset. We cannot mask IRQ because
126 * keyboard shares IRQ with us (Word has it as Bob Smelik's design).
127 * This problem is similar to what Alpha people suffer, see serial.c.
128 */
129 if (offset == UART_MCR)
130 value |= UART_MCR_OUT2;
131#endif
132 offset <<= up->port.regshift;
133
134 switch (up->port.iotype) {
135 case UPIO_HUB6:
136 outb(up->port.hub6 - 1 + offset, up->port.iobase);
137 outb(value, up->port.iobase + 1);
138 break;
139
140 case UPIO_MEM:
141 writeb(value, up->port.membase + offset);
142 break;
143
144 default:
145 outb(value, up->port.iobase + offset);
146 }
147}
148
149/*
150 * We used to support using pause I/O for certain machines. We
151 * haven't supported this for a while, but just in case it's badly
152 * needed for certain old 386 machines, I've left these #define's
153 * in....
154 */
155#define serial_inp(up, offset) serial_in(up, offset)
156#define serial_outp(up, offset, value) serial_out(up, offset, value)
157
158
159/*
160 * For the 16C950
161 */
162static void serial_icr_write(struct uart_sunsu_port *up, int offset, int value)
163{
164 serial_out(up, UART_SCR, offset);
165 serial_out(up, UART_ICR, value);
166}
167
168#if 0 /* Unused currently */
169static unsigned int serial_icr_read(struct uart_sunsu_port *up, int offset)
170{
171 unsigned int value;
172
173 serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
174 serial_out(up, UART_SCR, offset);
175 value = serial_in(up, UART_ICR);
176 serial_icr_write(up, UART_ACR, up->acr);
177
178 return value;
179}
180#endif
181
182#ifdef CONFIG_SERIAL_8250_RSA
183/*
184 * Attempts to turn on the RSA FIFO. Returns zero on failure.
185 * We set the port uart clock rate if we succeed.
186 */
187static int __enable_rsa(struct uart_sunsu_port *up)
188{
189 unsigned char mode;
190 int result;
191
192 mode = serial_inp(up, UART_RSA_MSR);
193 result = mode & UART_RSA_MSR_FIFO;
194
195 if (!result) {
196 serial_outp(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO);
197 mode = serial_inp(up, UART_RSA_MSR);
198 result = mode & UART_RSA_MSR_FIFO;
199 }
200
201 if (result)
202 up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16;
203
204 return result;
205}
206
207static void enable_rsa(struct uart_sunsu_port *up)
208{
209 if (up->port.type == PORT_RSA) {
210 if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) {
211 spin_lock_irq(&up->port.lock);
212 __enable_rsa(up);
213 spin_unlock_irq(&up->port.lock);
214 }
215 if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16)
216 serial_outp(up, UART_RSA_FRR, 0);
217 }
218}
219
220/*
221 * Attempts to turn off the RSA FIFO. Returns zero on failure.
222 * It is unknown why interrupts were disabled in here. However,
223 * the caller is expected to preserve this behaviour by grabbing
224 * the spinlock before calling this function.
225 */
226static void disable_rsa(struct uart_sunsu_port *up)
227{
228 unsigned char mode;
229 int result;
230
231 if (up->port.type == PORT_RSA &&
232 up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) {
233 spin_lock_irq(&up->port.lock);
234
235 mode = serial_inp(up, UART_RSA_MSR);
236 result = !(mode & UART_RSA_MSR_FIFO);
237
238 if (!result) {
239 serial_outp(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO);
240 mode = serial_inp(up, UART_RSA_MSR);
241 result = !(mode & UART_RSA_MSR_FIFO);
242 }
243
244 if (result)
245 up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16;
246 spin_unlock_irq(&up->port.lock);
247 }
248}
249#endif /* CONFIG_SERIAL_8250_RSA */
250
251static inline void __stop_tx(struct uart_sunsu_port *p)
252{
253 if (p->ier & UART_IER_THRI) {
254 p->ier &= ~UART_IER_THRI;
255 serial_out(p, UART_IER, p->ier);
256 }
257}
258
259static void sunsu_stop_tx(struct uart_port *port)
260{
261 struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
262
263 __stop_tx(up);
264
265 /*
266 * We really want to stop the transmitter from sending.
267 */
268 if (up->port.type == PORT_16C950) {
269 up->acr |= UART_ACR_TXDIS;
270 serial_icr_write(up, UART_ACR, up->acr);
271 }
272}
273
274static void sunsu_start_tx(struct uart_port *port)
275{
276 struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
277
278 if (!(up->ier & UART_IER_THRI)) {
279 up->ier |= UART_IER_THRI;
280 serial_out(up, UART_IER, up->ier);
281 }
282
283 /*
284 * Re-enable the transmitter if we disabled it.
285 */
286 if (up->port.type == PORT_16C950 && up->acr & UART_ACR_TXDIS) {
287 up->acr &= ~UART_ACR_TXDIS;
288 serial_icr_write(up, UART_ACR, up->acr);
289 }
290}
291
292static void sunsu_stop_rx(struct uart_port *port)
293{
294 struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
295
296 up->ier &= ~UART_IER_RLSI;
297 up->port.read_status_mask &= ~UART_LSR_DR;
298 serial_out(up, UART_IER, up->ier);
299}
300
301static void sunsu_enable_ms(struct uart_port *port)
302{
303 struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
304 unsigned long flags;
305
306 spin_lock_irqsave(&up->port.lock, flags);
307 up->ier |= UART_IER_MSI;
308 serial_out(up, UART_IER, up->ier);
309 spin_unlock_irqrestore(&up->port.lock, flags);
310}
311
312static struct tty_struct *
313receive_chars(struct uart_sunsu_port *up, unsigned char *status)
314{
315 struct tty_struct *tty = up->port.state->port.tty;
316 unsigned char ch, flag;
317 int max_count = 256;
318 int saw_console_brk = 0;
319
320 do {
321 ch = serial_inp(up, UART_RX);
322 flag = TTY_NORMAL;
323 up->port.icount.rx++;
324
325 if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE |
326 UART_LSR_FE | UART_LSR_OE))) {
327 /*
328 * For statistics only
329 */
330 if (*status & UART_LSR_BI) {
331 *status &= ~(UART_LSR_FE | UART_LSR_PE);
332 up->port.icount.brk++;
333 if (up->port.cons != NULL &&
334 up->port.line == up->port.cons->index)
335 saw_console_brk = 1;
336 /*
337 * We do the SysRQ and SAK checking
338 * here because otherwise the break
339 * may get masked by ignore_status_mask
340 * or read_status_mask.
341 */
342 if (uart_handle_break(&up->port))
343 goto ignore_char;
344 } else if (*status & UART_LSR_PE)
345 up->port.icount.parity++;
346 else if (*status & UART_LSR_FE)
347 up->port.icount.frame++;
348 if (*status & UART_LSR_OE)
349 up->port.icount.overrun++;
350
351 /*
352 * Mask off conditions which should be ingored.
353 */
354 *status &= up->port.read_status_mask;
355
356 if (up->port.cons != NULL &&
357 up->port.line == up->port.cons->index) {
358 /* Recover the break flag from console xmit */
359 *status |= up->lsr_break_flag;
360 up->lsr_break_flag = 0;
361 }
362
363 if (*status & UART_LSR_BI) {
364 flag = TTY_BREAK;
365 } else if (*status & UART_LSR_PE)
366 flag = TTY_PARITY;
367 else if (*status & UART_LSR_FE)
368 flag = TTY_FRAME;
369 }
370 if (uart_handle_sysrq_char(&up->port, ch))
371 goto ignore_char;
372 if ((*status & up->port.ignore_status_mask) == 0)
373 tty_insert_flip_char(tty, ch, flag);
374 if (*status & UART_LSR_OE)
375 /*
376 * Overrun is special, since it's reported
377 * immediately, and doesn't affect the current
378 * character.
379 */
380 tty_insert_flip_char(tty, 0, TTY_OVERRUN);
381 ignore_char:
382 *status = serial_inp(up, UART_LSR);
383 } while ((*status & UART_LSR_DR) && (max_count-- > 0));
384
385 if (saw_console_brk)
386 sun_do_break();
387
388 return tty;
389}
390
391static void transmit_chars(struct uart_sunsu_port *up)
392{
393 struct circ_buf *xmit = &up->port.state->xmit;
394 int count;
395
396 if (up->port.x_char) {
397 serial_outp(up, UART_TX, up->port.x_char);
398 up->port.icount.tx++;
399 up->port.x_char = 0;
400 return;
401 }
402 if (uart_tx_stopped(&up->port)) {
403 sunsu_stop_tx(&up->port);
404 return;
405 }
406 if (uart_circ_empty(xmit)) {
407 __stop_tx(up);
408 return;
409 }
410
411 count = up->port.fifosize;
412 do {
413 serial_out(up, UART_TX, xmit->buf[xmit->tail]);
414 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
415 up->port.icount.tx++;
416 if (uart_circ_empty(xmit))
417 break;
418 } while (--count > 0);
419
420 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
421 uart_write_wakeup(&up->port);
422
423 if (uart_circ_empty(xmit))
424 __stop_tx(up);
425}
426
427static void check_modem_status(struct uart_sunsu_port *up)
428{
429 int status;
430
431 status = serial_in(up, UART_MSR);
432
433 if ((status & UART_MSR_ANY_DELTA) == 0)
434 return;
435
436 if (status & UART_MSR_TERI)
437 up->port.icount.rng++;
438 if (status & UART_MSR_DDSR)
439 up->port.icount.dsr++;
440 if (status & UART_MSR_DDCD)
441 uart_handle_dcd_change(&up->port, status & UART_MSR_DCD);
442 if (status & UART_MSR_DCTS)
443 uart_handle_cts_change(&up->port, status & UART_MSR_CTS);
444
445 wake_up_interruptible(&up->port.state->port.delta_msr_wait);
446}
447
448static irqreturn_t sunsu_serial_interrupt(int irq, void *dev_id)
449{
450 struct uart_sunsu_port *up = dev_id;
451 unsigned long flags;
452 unsigned char status;
453
454 spin_lock_irqsave(&up->port.lock, flags);
455
456 do {
457 struct tty_struct *tty;
458
459 status = serial_inp(up, UART_LSR);
460 tty = NULL;
461 if (status & UART_LSR_DR)
462 tty = receive_chars(up, &status);
463 check_modem_status(up);
464 if (status & UART_LSR_THRE)
465 transmit_chars(up);
466
467 spin_unlock_irqrestore(&up->port.lock, flags);
468
469 if (tty)
470 tty_flip_buffer_push(tty);
471
472 spin_lock_irqsave(&up->port.lock, flags);
473
474 } while (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT));
475
476 spin_unlock_irqrestore(&up->port.lock, flags);
477
478 return IRQ_HANDLED;
479}
480
481/* Separate interrupt handling path for keyboard/mouse ports. */
482
483static void
484sunsu_change_speed(struct uart_port *port, unsigned int cflag,
485 unsigned int iflag, unsigned int quot);
486
487static void sunsu_change_mouse_baud(struct uart_sunsu_port *up)
488{
489 unsigned int cur_cflag = up->cflag;
490 int quot, new_baud;
491
492 up->cflag &= ~CBAUD;
493 up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud);
494
495 quot = up->port.uartclk / (16 * new_baud);
496
497 sunsu_change_speed(&up->port, up->cflag, 0, quot);
498}
499
500static void receive_kbd_ms_chars(struct uart_sunsu_port *up, int is_break)
501{
502 do {
503 unsigned char ch = serial_inp(up, UART_RX);
504
505 /* Stop-A is handled by drivers/char/keyboard.c now. */
506 if (up->su_type == SU_PORT_KBD) {
507#ifdef CONFIG_SERIO
508 serio_interrupt(&up->serio, ch, 0);
509#endif
510 } else if (up->su_type == SU_PORT_MS) {
511 int ret = suncore_mouse_baud_detection(ch, is_break);
512
513 switch (ret) {
514 case 2:
515 sunsu_change_mouse_baud(up);
516 /* fallthru */
517 case 1:
518 break;
519
520 case 0:
521#ifdef CONFIG_SERIO
522 serio_interrupt(&up->serio, ch, 0);
523#endif
524 break;
525 };
526 }
527 } while (serial_in(up, UART_LSR) & UART_LSR_DR);
528}
529
530static irqreturn_t sunsu_kbd_ms_interrupt(int irq, void *dev_id)
531{
532 struct uart_sunsu_port *up = dev_id;
533
534 if (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT)) {
535 unsigned char status = serial_inp(up, UART_LSR);
536
537 if ((status & UART_LSR_DR) || (status & UART_LSR_BI))
538 receive_kbd_ms_chars(up, (status & UART_LSR_BI) != 0);
539 }
540
541 return IRQ_HANDLED;
542}
543
544static unsigned int sunsu_tx_empty(struct uart_port *port)
545{
546 struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
547 unsigned long flags;
548 unsigned int ret;
549
550 spin_lock_irqsave(&up->port.lock, flags);
551 ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
552 spin_unlock_irqrestore(&up->port.lock, flags);
553
554 return ret;
555}
556
557static unsigned int sunsu_get_mctrl(struct uart_port *port)
558{
559 struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
560 unsigned char status;
561 unsigned int ret;
562
563 status = serial_in(up, UART_MSR);
564
565 ret = 0;
566 if (status & UART_MSR_DCD)
567 ret |= TIOCM_CAR;
568 if (status & UART_MSR_RI)
569 ret |= TIOCM_RNG;
570 if (status & UART_MSR_DSR)
571 ret |= TIOCM_DSR;
572 if (status & UART_MSR_CTS)
573 ret |= TIOCM_CTS;
574 return ret;
575}
576
577static void sunsu_set_mctrl(struct uart_port *port, unsigned int mctrl)
578{
579 struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
580 unsigned char mcr = 0;
581
582 if (mctrl & TIOCM_RTS)
583 mcr |= UART_MCR_RTS;
584 if (mctrl & TIOCM_DTR)
585 mcr |= UART_MCR_DTR;
586 if (mctrl & TIOCM_OUT1)
587 mcr |= UART_MCR_OUT1;
588 if (mctrl & TIOCM_OUT2)
589 mcr |= UART_MCR_OUT2;
590 if (mctrl & TIOCM_LOOP)
591 mcr |= UART_MCR_LOOP;
592
593 serial_out(up, UART_MCR, mcr);
594}
595
596static void sunsu_break_ctl(struct uart_port *port, int break_state)
597{
598 struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
599 unsigned long flags;
600
601 spin_lock_irqsave(&up->port.lock, flags);
602 if (break_state == -1)
603 up->lcr |= UART_LCR_SBC;
604 else
605 up->lcr &= ~UART_LCR_SBC;
606 serial_out(up, UART_LCR, up->lcr);
607 spin_unlock_irqrestore(&up->port.lock, flags);
608}
609
610static int sunsu_startup(struct uart_port *port)
611{
612 struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
613 unsigned long flags;
614 int retval;
615
616 if (up->port.type == PORT_16C950) {
617 /* Wake up and initialize UART */
618 up->acr = 0;
619 serial_outp(up, UART_LCR, 0xBF);
620 serial_outp(up, UART_EFR, UART_EFR_ECB);
621 serial_outp(up, UART_IER, 0);
622 serial_outp(up, UART_LCR, 0);
623 serial_icr_write(up, UART_CSR, 0); /* Reset the UART */
624 serial_outp(up, UART_LCR, 0xBF);
625 serial_outp(up, UART_EFR, UART_EFR_ECB);
626 serial_outp(up, UART_LCR, 0);
627 }
628
629#ifdef CONFIG_SERIAL_8250_RSA
630 /*
631 * If this is an RSA port, see if we can kick it up to the
632 * higher speed clock.
633 */
634 enable_rsa(up);
635#endif
636
637 /*
638 * Clear the FIFO buffers and disable them.
639 * (they will be reenabled in set_termios())
640 */
641 if (uart_config[up->port.type].flags & UART_CLEAR_FIFO) {
642 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
643 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
644 UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
645 serial_outp(up, UART_FCR, 0);
646 }
647
648 /*
649 * Clear the interrupt registers.
650 */
651 (void) serial_inp(up, UART_LSR);
652 (void) serial_inp(up, UART_RX);
653 (void) serial_inp(up, UART_IIR);
654 (void) serial_inp(up, UART_MSR);
655
656 /*
657 * At this point, there's no way the LSR could still be 0xff;
658 * if it is, then bail out, because there's likely no UART
659 * here.
660 */
661 if (!(up->port.flags & UPF_BUGGY_UART) &&
662 (serial_inp(up, UART_LSR) == 0xff)) {
663 printk("ttyS%d: LSR safety check engaged!\n", up->port.line);
664 return -ENODEV;
665 }
666
667 if (up->su_type != SU_PORT_PORT) {
668 retval = request_irq(up->port.irq, sunsu_kbd_ms_interrupt,
669 IRQF_SHARED, su_typev[up->su_type], up);
670 } else {
671 retval = request_irq(up->port.irq, sunsu_serial_interrupt,
672 IRQF_SHARED, su_typev[up->su_type], up);
673 }
674 if (retval) {
675 printk("su: Cannot register IRQ %d\n", up->port.irq);
676 return retval;
677 }
678
679 /*
680 * Now, initialize the UART
681 */
682 serial_outp(up, UART_LCR, UART_LCR_WLEN8);
683
684 spin_lock_irqsave(&up->port.lock, flags);
685
686 up->port.mctrl |= TIOCM_OUT2;
687
688 sunsu_set_mctrl(&up->port, up->port.mctrl);
689 spin_unlock_irqrestore(&up->port.lock, flags);
690
691 /*
692 * Finally, enable interrupts. Note: Modem status interrupts
693 * are set via set_termios(), which will be occurring imminently
694 * anyway, so we don't enable them here.
695 */
696 up->ier = UART_IER_RLSI | UART_IER_RDI;
697 serial_outp(up, UART_IER, up->ier);
698
699 if (up->port.flags & UPF_FOURPORT) {
700 unsigned int icp;
701 /*
702 * Enable interrupts on the AST Fourport board
703 */
704 icp = (up->port.iobase & 0xfe0) | 0x01f;
705 outb_p(0x80, icp);
706 (void) inb_p(icp);
707 }
708
709 /*
710 * And clear the interrupt registers again for luck.
711 */
712 (void) serial_inp(up, UART_LSR);
713 (void) serial_inp(up, UART_RX);
714 (void) serial_inp(up, UART_IIR);
715 (void) serial_inp(up, UART_MSR);
716
717 return 0;
718}
719
720static void sunsu_shutdown(struct uart_port *port)
721{
722 struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
723 unsigned long flags;
724
725 /*
726 * Disable interrupts from this port
727 */
728 up->ier = 0;
729 serial_outp(up, UART_IER, 0);
730
731 spin_lock_irqsave(&up->port.lock, flags);
732 if (up->port.flags & UPF_FOURPORT) {
733 /* reset interrupts on the AST Fourport board */
734 inb((up->port.iobase & 0xfe0) | 0x1f);
735 up->port.mctrl |= TIOCM_OUT1;
736 } else
737 up->port.mctrl &= ~TIOCM_OUT2;
738
739 sunsu_set_mctrl(&up->port, up->port.mctrl);
740 spin_unlock_irqrestore(&up->port.lock, flags);
741
742 /*
743 * Disable break condition and FIFOs
744 */
745 serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC);
746 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
747 UART_FCR_CLEAR_RCVR |
748 UART_FCR_CLEAR_XMIT);
749 serial_outp(up, UART_FCR, 0);
750
751#ifdef CONFIG_SERIAL_8250_RSA
752 /*
753 * Reset the RSA board back to 115kbps compat mode.
754 */
755 disable_rsa(up);
756#endif
757
758 /*
759 * Read data port to reset things.
760 */
761 (void) serial_in(up, UART_RX);
762
763 free_irq(up->port.irq, up);
764}
765
766static void
767sunsu_change_speed(struct uart_port *port, unsigned int cflag,
768 unsigned int iflag, unsigned int quot)
769{
770 struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
771 unsigned char cval, fcr = 0;
772 unsigned long flags;
773
774 switch (cflag & CSIZE) {
775 case CS5:
776 cval = 0x00;
777 break;
778 case CS6:
779 cval = 0x01;
780 break;
781 case CS7:
782 cval = 0x02;
783 break;
784 default:
785 case CS8:
786 cval = 0x03;
787 break;
788 }
789
790 if (cflag & CSTOPB)
791 cval |= 0x04;
792 if (cflag & PARENB)
793 cval |= UART_LCR_PARITY;
794 if (!(cflag & PARODD))
795 cval |= UART_LCR_EPAR;
796#ifdef CMSPAR
797 if (cflag & CMSPAR)
798 cval |= UART_LCR_SPAR;
799#endif
800
801 /*
802 * Work around a bug in the Oxford Semiconductor 952 rev B
803 * chip which causes it to seriously miscalculate baud rates
804 * when DLL is 0.
805 */
806 if ((quot & 0xff) == 0 && up->port.type == PORT_16C950 &&
807 up->rev == 0x5201)
808 quot ++;
809
810 if (uart_config[up->port.type].flags & UART_USE_FIFO) {
811 if ((up->port.uartclk / quot) < (2400 * 16))
812 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1;
813#ifdef CONFIG_SERIAL_8250_RSA
814 else if (up->port.type == PORT_RSA)
815 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_14;
816#endif
817 else
818 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_8;
819 }
820 if (up->port.type == PORT_16750)
821 fcr |= UART_FCR7_64BYTE;
822
823 /*
824 * Ok, we're now changing the port state. Do it with
825 * interrupts disabled.
826 */
827 spin_lock_irqsave(&up->port.lock, flags);
828
829 /*
830 * Update the per-port timeout.
831 */
832 uart_update_timeout(port, cflag, (port->uartclk / (16 * quot)));
833
834 up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
835 if (iflag & INPCK)
836 up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
837 if (iflag & (BRKINT | PARMRK))
838 up->port.read_status_mask |= UART_LSR_BI;
839
840 /*
841 * Characteres to ignore
842 */
843 up->port.ignore_status_mask = 0;
844 if (iflag & IGNPAR)
845 up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
846 if (iflag & IGNBRK) {
847 up->port.ignore_status_mask |= UART_LSR_BI;
848 /*
849 * If we're ignoring parity and break indicators,
850 * ignore overruns too (for real raw support).
851 */
852 if (iflag & IGNPAR)
853 up->port.ignore_status_mask |= UART_LSR_OE;
854 }
855
856 /*
857 * ignore all characters if CREAD is not set
858 */
859 if ((cflag & CREAD) == 0)
860 up->port.ignore_status_mask |= UART_LSR_DR;
861
862 /*
863 * CTS flow control flag and modem status interrupts
864 */
865 up->ier &= ~UART_IER_MSI;
866 if (UART_ENABLE_MS(&up->port, cflag))
867 up->ier |= UART_IER_MSI;
868
869 serial_out(up, UART_IER, up->ier);
870
871 if (uart_config[up->port.type].flags & UART_STARTECH) {
872 serial_outp(up, UART_LCR, 0xBF);
873 serial_outp(up, UART_EFR, cflag & CRTSCTS ? UART_EFR_CTS :0);
874 }
875 serial_outp(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */
876 serial_outp(up, UART_DLL, quot & 0xff); /* LS of divisor */
877 serial_outp(up, UART_DLM, quot >> 8); /* MS of divisor */
878 if (up->port.type == PORT_16750)
879 serial_outp(up, UART_FCR, fcr); /* set fcr */
880 serial_outp(up, UART_LCR, cval); /* reset DLAB */
881 up->lcr = cval; /* Save LCR */
882 if (up->port.type != PORT_16750) {
883 if (fcr & UART_FCR_ENABLE_FIFO) {
884 /* emulated UARTs (Lucent Venus 167x) need two steps */
885 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
886 }
887 serial_outp(up, UART_FCR, fcr); /* set fcr */
888 }
889
890 up->cflag = cflag;
891
892 spin_unlock_irqrestore(&up->port.lock, flags);
893}
894
895static void
896sunsu_set_termios(struct uart_port *port, struct ktermios *termios,
897 struct ktermios *old)
898{
899 unsigned int baud, quot;
900
901 /*
902 * Ask the core to calculate the divisor for us.
903 */
904 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
905 quot = uart_get_divisor(port, baud);
906
907 sunsu_change_speed(port, termios->c_cflag, termios->c_iflag, quot);
908}
909
910static void sunsu_release_port(struct uart_port *port)
911{
912}
913
914static int sunsu_request_port(struct uart_port *port)
915{
916 return 0;
917}
918
919static void sunsu_config_port(struct uart_port *port, int flags)
920{
921 struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
922
923 if (flags & UART_CONFIG_TYPE) {
924 /*
925 * We are supposed to call autoconfig here, but this requires
926 * splitting all the OBP probing crap from the UART probing.
927 * We'll do it when we kill sunsu.c altogether.
928 */
929 port->type = up->type_probed; /* XXX */
930 }
931}
932
933static int
934sunsu_verify_port(struct uart_port *port, struct serial_struct *ser)
935{
936 return -EINVAL;
937}
938
939static const char *
940sunsu_type(struct uart_port *port)
941{
942 int type = port->type;
943
944 if (type >= ARRAY_SIZE(uart_config))
945 type = 0;
946 return uart_config[type].name;
947}
948
949static struct uart_ops sunsu_pops = {
950 .tx_empty = sunsu_tx_empty,
951 .set_mctrl = sunsu_set_mctrl,
952 .get_mctrl = sunsu_get_mctrl,
953 .stop_tx = sunsu_stop_tx,
954 .start_tx = sunsu_start_tx,
955 .stop_rx = sunsu_stop_rx,
956 .enable_ms = sunsu_enable_ms,
957 .break_ctl = sunsu_break_ctl,
958 .startup = sunsu_startup,
959 .shutdown = sunsu_shutdown,
960 .set_termios = sunsu_set_termios,
961 .type = sunsu_type,
962 .release_port = sunsu_release_port,
963 .request_port = sunsu_request_port,
964 .config_port = sunsu_config_port,
965 .verify_port = sunsu_verify_port,
966};
967
968#define UART_NR 4
969
970static struct uart_sunsu_port sunsu_ports[UART_NR];
971
972#ifdef CONFIG_SERIO
973
974static DEFINE_SPINLOCK(sunsu_serio_lock);
975
976static int sunsu_serio_write(struct serio *serio, unsigned char ch)
977{
978 struct uart_sunsu_port *up = serio->port_data;
979 unsigned long flags;
980 int lsr;
981
982 spin_lock_irqsave(&sunsu_serio_lock, flags);
983
984 do {
985 lsr = serial_in(up, UART_LSR);
986 } while (!(lsr & UART_LSR_THRE));
987
988 /* Send the character out. */
989 serial_out(up, UART_TX, ch);
990
991 spin_unlock_irqrestore(&sunsu_serio_lock, flags);
992
993 return 0;
994}
995
996static int sunsu_serio_open(struct serio *serio)
997{
998 struct uart_sunsu_port *up = serio->port_data;
999 unsigned long flags;
1000 int ret;
1001
1002 spin_lock_irqsave(&sunsu_serio_lock, flags);
1003 if (!up->serio_open) {
1004 up->serio_open = 1;
1005 ret = 0;
1006 } else
1007 ret = -EBUSY;
1008 spin_unlock_irqrestore(&sunsu_serio_lock, flags);
1009
1010 return ret;
1011}
1012
1013static void sunsu_serio_close(struct serio *serio)
1014{
1015 struct uart_sunsu_port *up = serio->port_data;
1016 unsigned long flags;
1017
1018 spin_lock_irqsave(&sunsu_serio_lock, flags);
1019 up->serio_open = 0;
1020 spin_unlock_irqrestore(&sunsu_serio_lock, flags);
1021}
1022
1023#endif /* CONFIG_SERIO */
1024
1025static void sunsu_autoconfig(struct uart_sunsu_port *up)
1026{
1027 unsigned char status1, status2, scratch, scratch2, scratch3;
1028 unsigned char save_lcr, save_mcr;
1029 unsigned long flags;
1030
1031 if (up->su_type == SU_PORT_NONE)
1032 return;
1033
1034 up->type_probed = PORT_UNKNOWN;
1035 up->port.iotype = UPIO_MEM;
1036
1037 spin_lock_irqsave(&up->port.lock, flags);
1038
1039 if (!(up->port.flags & UPF_BUGGY_UART)) {
1040 /*
1041 * Do a simple existence test first; if we fail this, there's
1042 * no point trying anything else.
1043 *
1044 * 0x80 is used as a nonsense port to prevent against false
1045 * positives due to ISA bus float. The assumption is that
1046 * 0x80 is a non-existent port; which should be safe since
1047 * include/asm/io.h also makes this assumption.
1048 */
1049 scratch = serial_inp(up, UART_IER);
1050 serial_outp(up, UART_IER, 0);
1051#ifdef __i386__
1052 outb(0xff, 0x080);
1053#endif
1054 scratch2 = serial_inp(up, UART_IER);
1055 serial_outp(up, UART_IER, 0x0f);
1056#ifdef __i386__
1057 outb(0, 0x080);
1058#endif
1059 scratch3 = serial_inp(up, UART_IER);
1060 serial_outp(up, UART_IER, scratch);
1061 if (scratch2 != 0 || scratch3 != 0x0F)
1062 goto out; /* We failed; there's nothing here */
1063 }
1064
1065 save_mcr = serial_in(up, UART_MCR);
1066 save_lcr = serial_in(up, UART_LCR);
1067
1068 /*
1069 * Check to see if a UART is really there. Certain broken
1070 * internal modems based on the Rockwell chipset fail this
1071 * test, because they apparently don't implement the loopback
1072 * test mode. So this test is skipped on the COM 1 through
1073 * COM 4 ports. This *should* be safe, since no board
1074 * manufacturer would be stupid enough to design a board
1075 * that conflicts with COM 1-4 --- we hope!
1076 */
1077 if (!(up->port.flags & UPF_SKIP_TEST)) {
1078 serial_outp(up, UART_MCR, UART_MCR_LOOP | 0x0A);
1079 status1 = serial_inp(up, UART_MSR) & 0xF0;
1080 serial_outp(up, UART_MCR, save_mcr);
1081 if (status1 != 0x90)
1082 goto out; /* We failed loopback test */
1083 }
1084 serial_outp(up, UART_LCR, 0xBF); /* set up for StarTech test */
1085 serial_outp(up, UART_EFR, 0); /* EFR is the same as FCR */
1086 serial_outp(up, UART_LCR, 0);
1087 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
1088 scratch = serial_in(up, UART_IIR) >> 6;
1089 switch (scratch) {
1090 case 0:
1091 up->port.type = PORT_16450;
1092 break;
1093 case 1:
1094 up->port.type = PORT_UNKNOWN;
1095 break;
1096 case 2:
1097 up->port.type = PORT_16550;
1098 break;
1099 case 3:
1100 up->port.type = PORT_16550A;
1101 break;
1102 }
1103 if (up->port.type == PORT_16550A) {
1104 /* Check for Startech UART's */
1105 serial_outp(up, UART_LCR, UART_LCR_DLAB);
1106 if (serial_in(up, UART_EFR) == 0) {
1107 up->port.type = PORT_16650;
1108 } else {
1109 serial_outp(up, UART_LCR, 0xBF);
1110 if (serial_in(up, UART_EFR) == 0)
1111 up->port.type = PORT_16650V2;
1112 }
1113 }
1114 if (up->port.type == PORT_16550A) {
1115 /* Check for TI 16750 */
1116 serial_outp(up, UART_LCR, save_lcr | UART_LCR_DLAB);
1117 serial_outp(up, UART_FCR,
1118 UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
1119 scratch = serial_in(up, UART_IIR) >> 5;
1120 if (scratch == 7) {
1121 /*
1122 * If this is a 16750, and not a cheap UART
1123 * clone, then it should only go into 64 byte
1124 * mode if the UART_FCR7_64BYTE bit was set
1125 * while UART_LCR_DLAB was latched.
1126 */
1127 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
1128 serial_outp(up, UART_LCR, 0);
1129 serial_outp(up, UART_FCR,
1130 UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
1131 scratch = serial_in(up, UART_IIR) >> 5;
1132 if (scratch == 6)
1133 up->port.type = PORT_16750;
1134 }
1135 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
1136 }
1137 serial_outp(up, UART_LCR, save_lcr);
1138 if (up->port.type == PORT_16450) {
1139 scratch = serial_in(up, UART_SCR);
1140 serial_outp(up, UART_SCR, 0xa5);
1141 status1 = serial_in(up, UART_SCR);
1142 serial_outp(up, UART_SCR, 0x5a);
1143 status2 = serial_in(up, UART_SCR);
1144 serial_outp(up, UART_SCR, scratch);
1145
1146 if ((status1 != 0xa5) || (status2 != 0x5a))
1147 up->port.type = PORT_8250;
1148 }
1149
1150 up->port.fifosize = uart_config[up->port.type].dfl_xmit_fifo_size;
1151
1152 if (up->port.type == PORT_UNKNOWN)
1153 goto out;
1154 up->type_probed = up->port.type; /* XXX */
1155
1156 /*
1157 * Reset the UART.
1158 */
1159#ifdef CONFIG_SERIAL_8250_RSA
1160 if (up->port.type == PORT_RSA)
1161 serial_outp(up, UART_RSA_FRR, 0);
1162#endif
1163 serial_outp(up, UART_MCR, save_mcr);
1164 serial_outp(up, UART_FCR, (UART_FCR_ENABLE_FIFO |
1165 UART_FCR_CLEAR_RCVR |
1166 UART_FCR_CLEAR_XMIT));
1167 serial_outp(up, UART_FCR, 0);
1168 (void)serial_in(up, UART_RX);
1169 serial_outp(up, UART_IER, 0);
1170
1171out:
1172 spin_unlock_irqrestore(&up->port.lock, flags);
1173}
1174
1175static struct uart_driver sunsu_reg = {
1176 .owner = THIS_MODULE,
1177 .driver_name = "sunsu",
1178 .dev_name = "ttyS",
1179 .major = TTY_MAJOR,
1180};
1181
1182static int __devinit sunsu_kbd_ms_init(struct uart_sunsu_port *up)
1183{
1184 int quot, baud;
1185#ifdef CONFIG_SERIO
1186 struct serio *serio;
1187#endif
1188
1189 if (up->su_type == SU_PORT_KBD) {
1190 up->cflag = B1200 | CS8 | CLOCAL | CREAD;
1191 baud = 1200;
1192 } else {
1193 up->cflag = B4800 | CS8 | CLOCAL | CREAD;
1194 baud = 4800;
1195 }
1196 quot = up->port.uartclk / (16 * baud);
1197
1198 sunsu_autoconfig(up);
1199 if (up->port.type == PORT_UNKNOWN)
1200 return -ENODEV;
1201
1202 printk("%s: %s port at %llx, irq %u\n",
1203 up->port.dev->of_node->full_name,
1204 (up->su_type == SU_PORT_KBD) ? "Keyboard" : "Mouse",
1205 (unsigned long long) up->port.mapbase,
1206 up->port.irq);
1207
1208#ifdef CONFIG_SERIO
1209 serio = &up->serio;
1210 serio->port_data = up;
1211
1212 serio->id.type = SERIO_RS232;
1213 if (up->su_type == SU_PORT_KBD) {
1214 serio->id.proto = SERIO_SUNKBD;
1215 strlcpy(serio->name, "sukbd", sizeof(serio->name));
1216 } else {
1217 serio->id.proto = SERIO_SUN;
1218 serio->id.extra = 1;
1219 strlcpy(serio->name, "sums", sizeof(serio->name));
1220 }
1221 strlcpy(serio->phys,
1222 (!(up->port.line & 1) ? "su/serio0" : "su/serio1"),
1223 sizeof(serio->phys));
1224
1225 serio->write = sunsu_serio_write;
1226 serio->open = sunsu_serio_open;
1227 serio->close = sunsu_serio_close;
1228 serio->dev.parent = up->port.dev;
1229
1230 serio_register_port(serio);
1231#endif
1232
1233 sunsu_change_speed(&up->port, up->cflag, 0, quot);
1234
1235 sunsu_startup(&up->port);
1236 return 0;
1237}
1238
1239/*
1240 * ------------------------------------------------------------
1241 * Serial console driver
1242 * ------------------------------------------------------------
1243 */
1244
1245#ifdef CONFIG_SERIAL_SUNSU_CONSOLE
1246
1247#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
1248
1249/*
1250 * Wait for transmitter & holding register to empty
1251 */
1252static __inline__ void wait_for_xmitr(struct uart_sunsu_port *up)
1253{
1254 unsigned int status, tmout = 10000;
1255
1256 /* Wait up to 10ms for the character(s) to be sent. */
1257 do {
1258 status = serial_in(up, UART_LSR);
1259
1260 if (status & UART_LSR_BI)
1261 up->lsr_break_flag = UART_LSR_BI;
1262
1263 if (--tmout == 0)
1264 break;
1265 udelay(1);
1266 } while ((status & BOTH_EMPTY) != BOTH_EMPTY);
1267
1268 /* Wait up to 1s for flow control if necessary */
1269 if (up->port.flags & UPF_CONS_FLOW) {
1270 tmout = 1000000;
1271 while (--tmout &&
1272 ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0))
1273 udelay(1);
1274 }
1275}
1276
1277static void sunsu_console_putchar(struct uart_port *port, int ch)
1278{
1279 struct uart_sunsu_port *up = (struct uart_sunsu_port *)port;
1280
1281 wait_for_xmitr(up);
1282 serial_out(up, UART_TX, ch);
1283}
1284
1285/*
1286 * Print a string to the serial port trying not to disturb
1287 * any possible real use of the port...
1288 */
1289static void sunsu_console_write(struct console *co, const char *s,
1290 unsigned int count)
1291{
1292 struct uart_sunsu_port *up = &sunsu_ports[co->index];
1293 unsigned long flags;
1294 unsigned int ier;
1295 int locked = 1;
1296
1297 local_irq_save(flags);
1298 if (up->port.sysrq) {
1299 locked = 0;
1300 } else if (oops_in_progress) {
1301 locked = spin_trylock(&up->port.lock);
1302 } else
1303 spin_lock(&up->port.lock);
1304
1305 /*
1306 * First save the UER then disable the interrupts
1307 */
1308 ier = serial_in(up, UART_IER);
1309 serial_out(up, UART_IER, 0);
1310
1311 uart_console_write(&up->port, s, count, sunsu_console_putchar);
1312
1313 /*
1314 * Finally, wait for transmitter to become empty
1315 * and restore the IER
1316 */
1317 wait_for_xmitr(up);
1318 serial_out(up, UART_IER, ier);
1319
1320 if (locked)
1321 spin_unlock(&up->port.lock);
1322 local_irq_restore(flags);
1323}
1324
1325/*
1326 * Setup initial baud/bits/parity. We do two things here:
1327 * - construct a cflag setting for the first su_open()
1328 * - initialize the serial port
1329 * Return non-zero if we didn't find a serial port.
1330 */
1331static int __init sunsu_console_setup(struct console *co, char *options)
1332{
1333 static struct ktermios dummy;
1334 struct ktermios termios;
1335 struct uart_port *port;
1336
1337 printk("Console: ttyS%d (SU)\n",
1338 (sunsu_reg.minor - 64) + co->index);
1339
1340 /*
1341 * Check whether an invalid uart number has been specified, and
1342 * if so, search for the first available port that does have
1343 * console support.
1344 */
1345 if (co->index >= UART_NR)
1346 co->index = 0;
1347 port = &sunsu_ports[co->index].port;
1348
1349 /*
1350 * Temporary fix.
1351 */
1352 spin_lock_init(&port->lock);
1353
1354 /* Get firmware console settings. */
1355 sunserial_console_termios(co, port->dev->of_node);
1356
1357 memset(&termios, 0, sizeof(struct ktermios));
1358 termios.c_cflag = co->cflag;
1359 port->mctrl |= TIOCM_DTR;
1360 port->ops->set_termios(port, &termios, &dummy);
1361
1362 return 0;
1363}
1364
1365static struct console sunsu_console = {
1366 .name = "ttyS",
1367 .write = sunsu_console_write,
1368 .device = uart_console_device,
1369 .setup = sunsu_console_setup,
1370 .flags = CON_PRINTBUFFER,
1371 .index = -1,
1372 .data = &sunsu_reg,
1373};
1374
1375/*
1376 * Register console.
1377 */
1378
1379static inline struct console *SUNSU_CONSOLE(void)
1380{
1381 return &sunsu_console;
1382}
1383#else
1384#define SUNSU_CONSOLE() (NULL)
1385#define sunsu_serial_console_init() do { } while (0)
1386#endif
1387
1388static enum su_type __devinit su_get_type(struct device_node *dp)
1389{
1390 struct device_node *ap = of_find_node_by_path("/aliases");
1391
1392 if (ap) {
1393 const char *keyb = of_get_property(ap, "keyboard", NULL);
1394 const char *ms = of_get_property(ap, "mouse", NULL);
1395
1396 if (keyb) {
1397 if (dp == of_find_node_by_path(keyb))
1398 return SU_PORT_KBD;
1399 }
1400 if (ms) {
1401 if (dp == of_find_node_by_path(ms))
1402 return SU_PORT_MS;
1403 }
1404 }
1405
1406 return SU_PORT_PORT;
1407}
1408
1409static int __devinit su_probe(struct platform_device *op)
1410{
1411 static int inst;
1412 struct device_node *dp = op->dev.of_node;
1413 struct uart_sunsu_port *up;
1414 struct resource *rp;
1415 enum su_type type;
1416 bool ignore_line;
1417 int err;
1418
1419 type = su_get_type(dp);
1420 if (type == SU_PORT_PORT) {
1421 if (inst >= UART_NR)
1422 return -EINVAL;
1423 up = &sunsu_ports[inst];
1424 } else {
1425 up = kzalloc(sizeof(*up), GFP_KERNEL);
1426 if (!up)
1427 return -ENOMEM;
1428 }
1429
1430 up->port.line = inst;
1431
1432 spin_lock_init(&up->port.lock);
1433
1434 up->su_type = type;
1435
1436 rp = &op->resource[0];
1437 up->port.mapbase = rp->start;
1438 up->reg_size = resource_size(rp);
1439 up->port.membase = of_ioremap(rp, 0, up->reg_size, "su");
1440 if (!up->port.membase) {
1441 if (type != SU_PORT_PORT)
1442 kfree(up);
1443 return -ENOMEM;
1444 }
1445
1446 up->port.irq = op->archdata.irqs[0];
1447
1448 up->port.dev = &op->dev;
1449
1450 up->port.type = PORT_UNKNOWN;
1451 up->port.uartclk = (SU_BASE_BAUD * 16);
1452
1453 err = 0;
1454 if (up->su_type == SU_PORT_KBD || up->su_type == SU_PORT_MS) {
1455 err = sunsu_kbd_ms_init(up);
1456 if (err) {
1457 of_iounmap(&op->resource[0],
1458 up->port.membase, up->reg_size);
1459 kfree(up);
1460 return err;
1461 }
1462 dev_set_drvdata(&op->dev, up);
1463
1464 return 0;
1465 }
1466
1467 up->port.flags |= UPF_BOOT_AUTOCONF;
1468
1469 sunsu_autoconfig(up);
1470
1471 err = -ENODEV;
1472 if (up->port.type == PORT_UNKNOWN)
1473 goto out_unmap;
1474
1475 up->port.ops = &sunsu_pops;
1476
1477 ignore_line = false;
1478 if (!strcmp(dp->name, "rsc-console") ||
1479 !strcmp(dp->name, "lom-console"))
1480 ignore_line = true;
1481
1482 sunserial_console_match(SUNSU_CONSOLE(), dp,
1483 &sunsu_reg, up->port.line,
1484 ignore_line);
1485 err = uart_add_one_port(&sunsu_reg, &up->port);
1486 if (err)
1487 goto out_unmap;
1488
1489 dev_set_drvdata(&op->dev, up);
1490
1491 inst++;
1492
1493 return 0;
1494
1495out_unmap:
1496 of_iounmap(&op->resource[0], up->port.membase, up->reg_size);
1497 return err;
1498}
1499
1500static int __devexit su_remove(struct platform_device *op)
1501{
1502 struct uart_sunsu_port *up = dev_get_drvdata(&op->dev);
1503 bool kbdms = false;
1504
1505 if (up->su_type == SU_PORT_MS ||
1506 up->su_type == SU_PORT_KBD)
1507 kbdms = true;
1508
1509 if (kbdms) {
1510#ifdef CONFIG_SERIO
1511 serio_unregister_port(&up->serio);
1512#endif
1513 } else if (up->port.type != PORT_UNKNOWN)
1514 uart_remove_one_port(&sunsu_reg, &up->port);
1515
1516 if (up->port.membase)
1517 of_iounmap(&op->resource[0], up->port.membase, up->reg_size);
1518
1519 if (kbdms)
1520 kfree(up);
1521
1522 dev_set_drvdata(&op->dev, NULL);
1523
1524 return 0;
1525}
1526
1527static const struct of_device_id su_match[] = {
1528 {
1529 .name = "su",
1530 },
1531 {
1532 .name = "su_pnp",
1533 },
1534 {
1535 .name = "serial",
1536 .compatible = "su",
1537 },
1538 {
1539 .type = "serial",
1540 .compatible = "su",
1541 },
1542 {},
1543};
1544MODULE_DEVICE_TABLE(of, su_match);
1545
1546static struct platform_driver su_driver = {
1547 .driver = {
1548 .name = "su",
1549 .owner = THIS_MODULE,
1550 .of_match_table = su_match,
1551 },
1552 .probe = su_probe,
1553 .remove = __devexit_p(su_remove),
1554};
1555
1556static int __init sunsu_init(void)
1557{
1558 struct device_node *dp;
1559 int err;
1560 int num_uart = 0;
1561
1562 for_each_node_by_name(dp, "su") {
1563 if (su_get_type(dp) == SU_PORT_PORT)
1564 num_uart++;
1565 }
1566 for_each_node_by_name(dp, "su_pnp") {
1567 if (su_get_type(dp) == SU_PORT_PORT)
1568 num_uart++;
1569 }
1570 for_each_node_by_name(dp, "serial") {
1571 if (of_device_is_compatible(dp, "su")) {
1572 if (su_get_type(dp) == SU_PORT_PORT)
1573 num_uart++;
1574 }
1575 }
1576 for_each_node_by_type(dp, "serial") {
1577 if (of_device_is_compatible(dp, "su")) {
1578 if (su_get_type(dp) == SU_PORT_PORT)
1579 num_uart++;
1580 }
1581 }
1582
1583 if (num_uart) {
1584 err = sunserial_register_minors(&sunsu_reg, num_uart);
1585 if (err)
1586 return err;
1587 }
1588
1589 err = platform_driver_register(&su_driver);
1590 if (err && num_uart)
1591 sunserial_unregister_minors(&sunsu_reg, num_uart);
1592
1593 return err;
1594}
1595
1596static void __exit sunsu_exit(void)
1597{
1598 if (sunsu_reg.nr)
1599 sunserial_unregister_minors(&sunsu_reg, sunsu_reg.nr);
1600}
1601
1602module_init(sunsu_init);
1603module_exit(sunsu_exit);
1604
1605MODULE_AUTHOR("Eddie C. Dost, Peter Zaitcev, and David S. Miller");
1606MODULE_DESCRIPTION("Sun SU serial port driver");
1607MODULE_VERSION("2.0");
1608MODULE_LICENSE("GPL");
1/*
2 * su.c: Small serial driver for keyboard/mouse interface on sparc32/PCI
3 *
4 * Copyright (C) 1997 Eddie C. Dost (ecd@skynet.be)
5 * Copyright (C) 1998-1999 Pete Zaitcev (zaitcev@yahoo.com)
6 *
7 * This is mainly a variation of 8250.c, credits go to authors mentioned
8 * therein. In fact this driver should be merged into the generic 8250.c
9 * infrastructure perhaps using a 8250_sparc.c module.
10 *
11 * Fixed to use tty_get_baud_rate().
12 * Theodore Ts'o <tytso@mit.edu>, 2001-Oct-12
13 *
14 * Converted to new 2.5.x UART layer.
15 * David S. Miller (davem@davemloft.net), 2002-Jul-29
16 */
17
18#include <linux/module.h>
19#include <linux/kernel.h>
20#include <linux/spinlock.h>
21#include <linux/errno.h>
22#include <linux/tty.h>
23#include <linux/tty_flip.h>
24#include <linux/major.h>
25#include <linux/string.h>
26#include <linux/ptrace.h>
27#include <linux/ioport.h>
28#include <linux/circ_buf.h>
29#include <linux/serial.h>
30#include <linux/sysrq.h>
31#include <linux/console.h>
32#include <linux/slab.h>
33#ifdef CONFIG_SERIO
34#include <linux/serio.h>
35#endif
36#include <linux/serial_reg.h>
37#include <linux/init.h>
38#include <linux/delay.h>
39#include <linux/of_device.h>
40
41#include <asm/io.h>
42#include <asm/irq.h>
43#include <asm/prom.h>
44#include <asm/setup.h>
45
46#if defined(CONFIG_SERIAL_SUNSU_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
47#define SUPPORT_SYSRQ
48#endif
49
50#include <linux/serial_core.h>
51#include <linux/sunserialcore.h>
52
53/* We are on a NS PC87303 clocked with 24.0 MHz, which results
54 * in a UART clock of 1.8462 MHz.
55 */
56#define SU_BASE_BAUD (1846200 / 16)
57
58enum su_type { SU_PORT_NONE, SU_PORT_MS, SU_PORT_KBD, SU_PORT_PORT };
59static char *su_typev[] = { "su(???)", "su(mouse)", "su(kbd)", "su(serial)" };
60
61struct serial_uart_config {
62 char *name;
63 int dfl_xmit_fifo_size;
64 int flags;
65};
66
67/*
68 * Here we define the default xmit fifo size used for each type of UART.
69 */
70static const struct serial_uart_config uart_config[] = {
71 { "unknown", 1, 0 },
72 { "8250", 1, 0 },
73 { "16450", 1, 0 },
74 { "16550", 1, 0 },
75 { "16550A", 16, UART_CLEAR_FIFO | UART_USE_FIFO },
76 { "Cirrus", 1, 0 },
77 { "ST16650", 1, UART_CLEAR_FIFO | UART_STARTECH },
78 { "ST16650V2", 32, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
79 { "TI16750", 64, UART_CLEAR_FIFO | UART_USE_FIFO },
80 { "Startech", 1, 0 },
81 { "16C950/954", 128, UART_CLEAR_FIFO | UART_USE_FIFO },
82 { "ST16654", 64, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
83 { "XR16850", 128, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
84 { "RSA", 2048, UART_CLEAR_FIFO | UART_USE_FIFO }
85};
86
87struct uart_sunsu_port {
88 struct uart_port port;
89 unsigned char acr;
90 unsigned char ier;
91 unsigned short rev;
92 unsigned char lcr;
93 unsigned int lsr_break_flag;
94 unsigned int cflag;
95
96 /* Probing information. */
97 enum su_type su_type;
98 unsigned int type_probed; /* XXX Stupid */
99 unsigned long reg_size;
100
101#ifdef CONFIG_SERIO
102 struct serio serio;
103 int serio_open;
104#endif
105};
106
107static unsigned int serial_in(struct uart_sunsu_port *up, int offset)
108{
109 offset <<= up->port.regshift;
110
111 switch (up->port.iotype) {
112 case UPIO_HUB6:
113 outb(up->port.hub6 - 1 + offset, up->port.iobase);
114 return inb(up->port.iobase + 1);
115
116 case UPIO_MEM:
117 return readb(up->port.membase + offset);
118
119 default:
120 return inb(up->port.iobase + offset);
121 }
122}
123
124static void serial_out(struct uart_sunsu_port *up, int offset, int value)
125{
126#ifndef CONFIG_SPARC64
127 /*
128 * MrCoffee has weird schematics: IRQ4 & P10(?) pins of SuperIO are
129 * connected with a gate then go to SlavIO. When IRQ4 goes tristated
130 * gate outputs a logical one. Since we use level triggered interrupts
131 * we have lockup and watchdog reset. We cannot mask IRQ because
132 * keyboard shares IRQ with us (Word has it as Bob Smelik's design).
133 * This problem is similar to what Alpha people suffer, see serial.c.
134 */
135 if (offset == UART_MCR)
136 value |= UART_MCR_OUT2;
137#endif
138 offset <<= up->port.regshift;
139
140 switch (up->port.iotype) {
141 case UPIO_HUB6:
142 outb(up->port.hub6 - 1 + offset, up->port.iobase);
143 outb(value, up->port.iobase + 1);
144 break;
145
146 case UPIO_MEM:
147 writeb(value, up->port.membase + offset);
148 break;
149
150 default:
151 outb(value, up->port.iobase + offset);
152 }
153}
154
155/*
156 * We used to support using pause I/O for certain machines. We
157 * haven't supported this for a while, but just in case it's badly
158 * needed for certain old 386 machines, I've left these #define's
159 * in....
160 */
161#define serial_inp(up, offset) serial_in(up, offset)
162#define serial_outp(up, offset, value) serial_out(up, offset, value)
163
164
165/*
166 * For the 16C950
167 */
168static void serial_icr_write(struct uart_sunsu_port *up, int offset, int value)
169{
170 serial_out(up, UART_SCR, offset);
171 serial_out(up, UART_ICR, value);
172}
173
174#if 0 /* Unused currently */
175static unsigned int serial_icr_read(struct uart_sunsu_port *up, int offset)
176{
177 unsigned int value;
178
179 serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
180 serial_out(up, UART_SCR, offset);
181 value = serial_in(up, UART_ICR);
182 serial_icr_write(up, UART_ACR, up->acr);
183
184 return value;
185}
186#endif
187
188#ifdef CONFIG_SERIAL_8250_RSA
189/*
190 * Attempts to turn on the RSA FIFO. Returns zero on failure.
191 * We set the port uart clock rate if we succeed.
192 */
193static int __enable_rsa(struct uart_sunsu_port *up)
194{
195 unsigned char mode;
196 int result;
197
198 mode = serial_inp(up, UART_RSA_MSR);
199 result = mode & UART_RSA_MSR_FIFO;
200
201 if (!result) {
202 serial_outp(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO);
203 mode = serial_inp(up, UART_RSA_MSR);
204 result = mode & UART_RSA_MSR_FIFO;
205 }
206
207 if (result)
208 up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16;
209
210 return result;
211}
212
213static void enable_rsa(struct uart_sunsu_port *up)
214{
215 if (up->port.type == PORT_RSA) {
216 if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) {
217 spin_lock_irq(&up->port.lock);
218 __enable_rsa(up);
219 spin_unlock_irq(&up->port.lock);
220 }
221 if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16)
222 serial_outp(up, UART_RSA_FRR, 0);
223 }
224}
225
226/*
227 * Attempts to turn off the RSA FIFO. Returns zero on failure.
228 * It is unknown why interrupts were disabled in here. However,
229 * the caller is expected to preserve this behaviour by grabbing
230 * the spinlock before calling this function.
231 */
232static void disable_rsa(struct uart_sunsu_port *up)
233{
234 unsigned char mode;
235 int result;
236
237 if (up->port.type == PORT_RSA &&
238 up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) {
239 spin_lock_irq(&up->port.lock);
240
241 mode = serial_inp(up, UART_RSA_MSR);
242 result = !(mode & UART_RSA_MSR_FIFO);
243
244 if (!result) {
245 serial_outp(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO);
246 mode = serial_inp(up, UART_RSA_MSR);
247 result = !(mode & UART_RSA_MSR_FIFO);
248 }
249
250 if (result)
251 up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16;
252 spin_unlock_irq(&up->port.lock);
253 }
254}
255#endif /* CONFIG_SERIAL_8250_RSA */
256
257static inline void __stop_tx(struct uart_sunsu_port *p)
258{
259 if (p->ier & UART_IER_THRI) {
260 p->ier &= ~UART_IER_THRI;
261 serial_out(p, UART_IER, p->ier);
262 }
263}
264
265static void sunsu_stop_tx(struct uart_port *port)
266{
267 struct uart_sunsu_port *up =
268 container_of(port, struct uart_sunsu_port, port);
269
270 __stop_tx(up);
271
272 /*
273 * We really want to stop the transmitter from sending.
274 */
275 if (up->port.type == PORT_16C950) {
276 up->acr |= UART_ACR_TXDIS;
277 serial_icr_write(up, UART_ACR, up->acr);
278 }
279}
280
281static void sunsu_start_tx(struct uart_port *port)
282{
283 struct uart_sunsu_port *up =
284 container_of(port, struct uart_sunsu_port, port);
285
286 if (!(up->ier & UART_IER_THRI)) {
287 up->ier |= UART_IER_THRI;
288 serial_out(up, UART_IER, up->ier);
289 }
290
291 /*
292 * Re-enable the transmitter if we disabled it.
293 */
294 if (up->port.type == PORT_16C950 && up->acr & UART_ACR_TXDIS) {
295 up->acr &= ~UART_ACR_TXDIS;
296 serial_icr_write(up, UART_ACR, up->acr);
297 }
298}
299
300static void sunsu_stop_rx(struct uart_port *port)
301{
302 struct uart_sunsu_port *up =
303 container_of(port, struct uart_sunsu_port, port);
304
305 up->ier &= ~UART_IER_RLSI;
306 up->port.read_status_mask &= ~UART_LSR_DR;
307 serial_out(up, UART_IER, up->ier);
308}
309
310static void sunsu_enable_ms(struct uart_port *port)
311{
312 struct uart_sunsu_port *up =
313 container_of(port, struct uart_sunsu_port, port);
314 unsigned long flags;
315
316 spin_lock_irqsave(&up->port.lock, flags);
317 up->ier |= UART_IER_MSI;
318 serial_out(up, UART_IER, up->ier);
319 spin_unlock_irqrestore(&up->port.lock, flags);
320}
321
322static void
323receive_chars(struct uart_sunsu_port *up, unsigned char *status)
324{
325 struct tty_port *port = &up->port.state->port;
326 unsigned char ch, flag;
327 int max_count = 256;
328 int saw_console_brk = 0;
329
330 do {
331 ch = serial_inp(up, UART_RX);
332 flag = TTY_NORMAL;
333 up->port.icount.rx++;
334
335 if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE |
336 UART_LSR_FE | UART_LSR_OE))) {
337 /*
338 * For statistics only
339 */
340 if (*status & UART_LSR_BI) {
341 *status &= ~(UART_LSR_FE | UART_LSR_PE);
342 up->port.icount.brk++;
343 if (up->port.cons != NULL &&
344 up->port.line == up->port.cons->index)
345 saw_console_brk = 1;
346 /*
347 * We do the SysRQ and SAK checking
348 * here because otherwise the break
349 * may get masked by ignore_status_mask
350 * or read_status_mask.
351 */
352 if (uart_handle_break(&up->port))
353 goto ignore_char;
354 } else if (*status & UART_LSR_PE)
355 up->port.icount.parity++;
356 else if (*status & UART_LSR_FE)
357 up->port.icount.frame++;
358 if (*status & UART_LSR_OE)
359 up->port.icount.overrun++;
360
361 /*
362 * Mask off conditions which should be ingored.
363 */
364 *status &= up->port.read_status_mask;
365
366 if (up->port.cons != NULL &&
367 up->port.line == up->port.cons->index) {
368 /* Recover the break flag from console xmit */
369 *status |= up->lsr_break_flag;
370 up->lsr_break_flag = 0;
371 }
372
373 if (*status & UART_LSR_BI) {
374 flag = TTY_BREAK;
375 } else if (*status & UART_LSR_PE)
376 flag = TTY_PARITY;
377 else if (*status & UART_LSR_FE)
378 flag = TTY_FRAME;
379 }
380 if (uart_handle_sysrq_char(&up->port, ch))
381 goto ignore_char;
382 if ((*status & up->port.ignore_status_mask) == 0)
383 tty_insert_flip_char(port, ch, flag);
384 if (*status & UART_LSR_OE)
385 /*
386 * Overrun is special, since it's reported
387 * immediately, and doesn't affect the current
388 * character.
389 */
390 tty_insert_flip_char(port, 0, TTY_OVERRUN);
391 ignore_char:
392 *status = serial_inp(up, UART_LSR);
393 } while ((*status & UART_LSR_DR) && (max_count-- > 0));
394
395 if (saw_console_brk)
396 sun_do_break();
397}
398
399static void transmit_chars(struct uart_sunsu_port *up)
400{
401 struct circ_buf *xmit = &up->port.state->xmit;
402 int count;
403
404 if (up->port.x_char) {
405 serial_outp(up, UART_TX, up->port.x_char);
406 up->port.icount.tx++;
407 up->port.x_char = 0;
408 return;
409 }
410 if (uart_tx_stopped(&up->port)) {
411 sunsu_stop_tx(&up->port);
412 return;
413 }
414 if (uart_circ_empty(xmit)) {
415 __stop_tx(up);
416 return;
417 }
418
419 count = up->port.fifosize;
420 do {
421 serial_out(up, UART_TX, xmit->buf[xmit->tail]);
422 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
423 up->port.icount.tx++;
424 if (uart_circ_empty(xmit))
425 break;
426 } while (--count > 0);
427
428 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
429 uart_write_wakeup(&up->port);
430
431 if (uart_circ_empty(xmit))
432 __stop_tx(up);
433}
434
435static void check_modem_status(struct uart_sunsu_port *up)
436{
437 int status;
438
439 status = serial_in(up, UART_MSR);
440
441 if ((status & UART_MSR_ANY_DELTA) == 0)
442 return;
443
444 if (status & UART_MSR_TERI)
445 up->port.icount.rng++;
446 if (status & UART_MSR_DDSR)
447 up->port.icount.dsr++;
448 if (status & UART_MSR_DDCD)
449 uart_handle_dcd_change(&up->port, status & UART_MSR_DCD);
450 if (status & UART_MSR_DCTS)
451 uart_handle_cts_change(&up->port, status & UART_MSR_CTS);
452
453 wake_up_interruptible(&up->port.state->port.delta_msr_wait);
454}
455
456static irqreturn_t sunsu_serial_interrupt(int irq, void *dev_id)
457{
458 struct uart_sunsu_port *up = dev_id;
459 unsigned long flags;
460 unsigned char status;
461
462 spin_lock_irqsave(&up->port.lock, flags);
463
464 do {
465 status = serial_inp(up, UART_LSR);
466 if (status & UART_LSR_DR)
467 receive_chars(up, &status);
468 check_modem_status(up);
469 if (status & UART_LSR_THRE)
470 transmit_chars(up);
471
472 spin_unlock_irqrestore(&up->port.lock, flags);
473
474 tty_flip_buffer_push(&up->port.state->port);
475
476 spin_lock_irqsave(&up->port.lock, flags);
477
478 } while (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT));
479
480 spin_unlock_irqrestore(&up->port.lock, flags);
481
482 return IRQ_HANDLED;
483}
484
485/* Separate interrupt handling path for keyboard/mouse ports. */
486
487static void
488sunsu_change_speed(struct uart_port *port, unsigned int cflag,
489 unsigned int iflag, unsigned int quot);
490
491static void sunsu_change_mouse_baud(struct uart_sunsu_port *up)
492{
493 unsigned int cur_cflag = up->cflag;
494 int quot, new_baud;
495
496 up->cflag &= ~CBAUD;
497 up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud);
498
499 quot = up->port.uartclk / (16 * new_baud);
500
501 sunsu_change_speed(&up->port, up->cflag, 0, quot);
502}
503
504static void receive_kbd_ms_chars(struct uart_sunsu_port *up, int is_break)
505{
506 do {
507 unsigned char ch = serial_inp(up, UART_RX);
508
509 /* Stop-A is handled by drivers/char/keyboard.c now. */
510 if (up->su_type == SU_PORT_KBD) {
511#ifdef CONFIG_SERIO
512 serio_interrupt(&up->serio, ch, 0);
513#endif
514 } else if (up->su_type == SU_PORT_MS) {
515 int ret = suncore_mouse_baud_detection(ch, is_break);
516
517 switch (ret) {
518 case 2:
519 sunsu_change_mouse_baud(up);
520 /* fallthru */
521 case 1:
522 break;
523
524 case 0:
525#ifdef CONFIG_SERIO
526 serio_interrupt(&up->serio, ch, 0);
527#endif
528 break;
529 }
530 }
531 } while (serial_in(up, UART_LSR) & UART_LSR_DR);
532}
533
534static irqreturn_t sunsu_kbd_ms_interrupt(int irq, void *dev_id)
535{
536 struct uart_sunsu_port *up = dev_id;
537
538 if (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT)) {
539 unsigned char status = serial_inp(up, UART_LSR);
540
541 if ((status & UART_LSR_DR) || (status & UART_LSR_BI))
542 receive_kbd_ms_chars(up, (status & UART_LSR_BI) != 0);
543 }
544
545 return IRQ_HANDLED;
546}
547
548static unsigned int sunsu_tx_empty(struct uart_port *port)
549{
550 struct uart_sunsu_port *up =
551 container_of(port, struct uart_sunsu_port, port);
552 unsigned long flags;
553 unsigned int ret;
554
555 spin_lock_irqsave(&up->port.lock, flags);
556 ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
557 spin_unlock_irqrestore(&up->port.lock, flags);
558
559 return ret;
560}
561
562static unsigned int sunsu_get_mctrl(struct uart_port *port)
563{
564 struct uart_sunsu_port *up =
565 container_of(port, struct uart_sunsu_port, port);
566 unsigned char status;
567 unsigned int ret;
568
569 status = serial_in(up, UART_MSR);
570
571 ret = 0;
572 if (status & UART_MSR_DCD)
573 ret |= TIOCM_CAR;
574 if (status & UART_MSR_RI)
575 ret |= TIOCM_RNG;
576 if (status & UART_MSR_DSR)
577 ret |= TIOCM_DSR;
578 if (status & UART_MSR_CTS)
579 ret |= TIOCM_CTS;
580 return ret;
581}
582
583static void sunsu_set_mctrl(struct uart_port *port, unsigned int mctrl)
584{
585 struct uart_sunsu_port *up =
586 container_of(port, struct uart_sunsu_port, port);
587 unsigned char mcr = 0;
588
589 if (mctrl & TIOCM_RTS)
590 mcr |= UART_MCR_RTS;
591 if (mctrl & TIOCM_DTR)
592 mcr |= UART_MCR_DTR;
593 if (mctrl & TIOCM_OUT1)
594 mcr |= UART_MCR_OUT1;
595 if (mctrl & TIOCM_OUT2)
596 mcr |= UART_MCR_OUT2;
597 if (mctrl & TIOCM_LOOP)
598 mcr |= UART_MCR_LOOP;
599
600 serial_out(up, UART_MCR, mcr);
601}
602
603static void sunsu_break_ctl(struct uart_port *port, int break_state)
604{
605 struct uart_sunsu_port *up =
606 container_of(port, struct uart_sunsu_port, port);
607 unsigned long flags;
608
609 spin_lock_irqsave(&up->port.lock, flags);
610 if (break_state == -1)
611 up->lcr |= UART_LCR_SBC;
612 else
613 up->lcr &= ~UART_LCR_SBC;
614 serial_out(up, UART_LCR, up->lcr);
615 spin_unlock_irqrestore(&up->port.lock, flags);
616}
617
618static int sunsu_startup(struct uart_port *port)
619{
620 struct uart_sunsu_port *up =
621 container_of(port, struct uart_sunsu_port, port);
622 unsigned long flags;
623 int retval;
624
625 if (up->port.type == PORT_16C950) {
626 /* Wake up and initialize UART */
627 up->acr = 0;
628 serial_outp(up, UART_LCR, 0xBF);
629 serial_outp(up, UART_EFR, UART_EFR_ECB);
630 serial_outp(up, UART_IER, 0);
631 serial_outp(up, UART_LCR, 0);
632 serial_icr_write(up, UART_CSR, 0); /* Reset the UART */
633 serial_outp(up, UART_LCR, 0xBF);
634 serial_outp(up, UART_EFR, UART_EFR_ECB);
635 serial_outp(up, UART_LCR, 0);
636 }
637
638#ifdef CONFIG_SERIAL_8250_RSA
639 /*
640 * If this is an RSA port, see if we can kick it up to the
641 * higher speed clock.
642 */
643 enable_rsa(up);
644#endif
645
646 /*
647 * Clear the FIFO buffers and disable them.
648 * (they will be reenabled in set_termios())
649 */
650 if (uart_config[up->port.type].flags & UART_CLEAR_FIFO) {
651 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
652 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
653 UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
654 serial_outp(up, UART_FCR, 0);
655 }
656
657 /*
658 * Clear the interrupt registers.
659 */
660 (void) serial_inp(up, UART_LSR);
661 (void) serial_inp(up, UART_RX);
662 (void) serial_inp(up, UART_IIR);
663 (void) serial_inp(up, UART_MSR);
664
665 /*
666 * At this point, there's no way the LSR could still be 0xff;
667 * if it is, then bail out, because there's likely no UART
668 * here.
669 */
670 if (!(up->port.flags & UPF_BUGGY_UART) &&
671 (serial_inp(up, UART_LSR) == 0xff)) {
672 printk("ttyS%d: LSR safety check engaged!\n", up->port.line);
673 return -ENODEV;
674 }
675
676 if (up->su_type != SU_PORT_PORT) {
677 retval = request_irq(up->port.irq, sunsu_kbd_ms_interrupt,
678 IRQF_SHARED, su_typev[up->su_type], up);
679 } else {
680 retval = request_irq(up->port.irq, sunsu_serial_interrupt,
681 IRQF_SHARED, su_typev[up->su_type], up);
682 }
683 if (retval) {
684 printk("su: Cannot register IRQ %d\n", up->port.irq);
685 return retval;
686 }
687
688 /*
689 * Now, initialize the UART
690 */
691 serial_outp(up, UART_LCR, UART_LCR_WLEN8);
692
693 spin_lock_irqsave(&up->port.lock, flags);
694
695 up->port.mctrl |= TIOCM_OUT2;
696
697 sunsu_set_mctrl(&up->port, up->port.mctrl);
698 spin_unlock_irqrestore(&up->port.lock, flags);
699
700 /*
701 * Finally, enable interrupts. Note: Modem status interrupts
702 * are set via set_termios(), which will be occurring imminently
703 * anyway, so we don't enable them here.
704 */
705 up->ier = UART_IER_RLSI | UART_IER_RDI;
706 serial_outp(up, UART_IER, up->ier);
707
708 if (up->port.flags & UPF_FOURPORT) {
709 unsigned int icp;
710 /*
711 * Enable interrupts on the AST Fourport board
712 */
713 icp = (up->port.iobase & 0xfe0) | 0x01f;
714 outb_p(0x80, icp);
715 (void) inb_p(icp);
716 }
717
718 /*
719 * And clear the interrupt registers again for luck.
720 */
721 (void) serial_inp(up, UART_LSR);
722 (void) serial_inp(up, UART_RX);
723 (void) serial_inp(up, UART_IIR);
724 (void) serial_inp(up, UART_MSR);
725
726 return 0;
727}
728
729static void sunsu_shutdown(struct uart_port *port)
730{
731 struct uart_sunsu_port *up =
732 container_of(port, struct uart_sunsu_port, port);
733 unsigned long flags;
734
735 /*
736 * Disable interrupts from this port
737 */
738 up->ier = 0;
739 serial_outp(up, UART_IER, 0);
740
741 spin_lock_irqsave(&up->port.lock, flags);
742 if (up->port.flags & UPF_FOURPORT) {
743 /* reset interrupts on the AST Fourport board */
744 inb((up->port.iobase & 0xfe0) | 0x1f);
745 up->port.mctrl |= TIOCM_OUT1;
746 } else
747 up->port.mctrl &= ~TIOCM_OUT2;
748
749 sunsu_set_mctrl(&up->port, up->port.mctrl);
750 spin_unlock_irqrestore(&up->port.lock, flags);
751
752 /*
753 * Disable break condition and FIFOs
754 */
755 serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC);
756 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
757 UART_FCR_CLEAR_RCVR |
758 UART_FCR_CLEAR_XMIT);
759 serial_outp(up, UART_FCR, 0);
760
761#ifdef CONFIG_SERIAL_8250_RSA
762 /*
763 * Reset the RSA board back to 115kbps compat mode.
764 */
765 disable_rsa(up);
766#endif
767
768 /*
769 * Read data port to reset things.
770 */
771 (void) serial_in(up, UART_RX);
772
773 free_irq(up->port.irq, up);
774}
775
776static void
777sunsu_change_speed(struct uart_port *port, unsigned int cflag,
778 unsigned int iflag, unsigned int quot)
779{
780 struct uart_sunsu_port *up =
781 container_of(port, struct uart_sunsu_port, port);
782 unsigned char cval, fcr = 0;
783 unsigned long flags;
784
785 switch (cflag & CSIZE) {
786 case CS5:
787 cval = 0x00;
788 break;
789 case CS6:
790 cval = 0x01;
791 break;
792 case CS7:
793 cval = 0x02;
794 break;
795 default:
796 case CS8:
797 cval = 0x03;
798 break;
799 }
800
801 if (cflag & CSTOPB)
802 cval |= 0x04;
803 if (cflag & PARENB)
804 cval |= UART_LCR_PARITY;
805 if (!(cflag & PARODD))
806 cval |= UART_LCR_EPAR;
807#ifdef CMSPAR
808 if (cflag & CMSPAR)
809 cval |= UART_LCR_SPAR;
810#endif
811
812 /*
813 * Work around a bug in the Oxford Semiconductor 952 rev B
814 * chip which causes it to seriously miscalculate baud rates
815 * when DLL is 0.
816 */
817 if ((quot & 0xff) == 0 && up->port.type == PORT_16C950 &&
818 up->rev == 0x5201)
819 quot ++;
820
821 if (uart_config[up->port.type].flags & UART_USE_FIFO) {
822 if ((up->port.uartclk / quot) < (2400 * 16))
823 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1;
824#ifdef CONFIG_SERIAL_8250_RSA
825 else if (up->port.type == PORT_RSA)
826 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_14;
827#endif
828 else
829 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_8;
830 }
831 if (up->port.type == PORT_16750)
832 fcr |= UART_FCR7_64BYTE;
833
834 /*
835 * Ok, we're now changing the port state. Do it with
836 * interrupts disabled.
837 */
838 spin_lock_irqsave(&up->port.lock, flags);
839
840 /*
841 * Update the per-port timeout.
842 */
843 uart_update_timeout(port, cflag, (port->uartclk / (16 * quot)));
844
845 up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
846 if (iflag & INPCK)
847 up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
848 if (iflag & (IGNBRK | BRKINT | PARMRK))
849 up->port.read_status_mask |= UART_LSR_BI;
850
851 /*
852 * Characteres to ignore
853 */
854 up->port.ignore_status_mask = 0;
855 if (iflag & IGNPAR)
856 up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
857 if (iflag & IGNBRK) {
858 up->port.ignore_status_mask |= UART_LSR_BI;
859 /*
860 * If we're ignoring parity and break indicators,
861 * ignore overruns too (for real raw support).
862 */
863 if (iflag & IGNPAR)
864 up->port.ignore_status_mask |= UART_LSR_OE;
865 }
866
867 /*
868 * ignore all characters if CREAD is not set
869 */
870 if ((cflag & CREAD) == 0)
871 up->port.ignore_status_mask |= UART_LSR_DR;
872
873 /*
874 * CTS flow control flag and modem status interrupts
875 */
876 up->ier &= ~UART_IER_MSI;
877 if (UART_ENABLE_MS(&up->port, cflag))
878 up->ier |= UART_IER_MSI;
879
880 serial_out(up, UART_IER, up->ier);
881
882 if (uart_config[up->port.type].flags & UART_STARTECH) {
883 serial_outp(up, UART_LCR, 0xBF);
884 serial_outp(up, UART_EFR, cflag & CRTSCTS ? UART_EFR_CTS :0);
885 }
886 serial_outp(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */
887 serial_outp(up, UART_DLL, quot & 0xff); /* LS of divisor */
888 serial_outp(up, UART_DLM, quot >> 8); /* MS of divisor */
889 if (up->port.type == PORT_16750)
890 serial_outp(up, UART_FCR, fcr); /* set fcr */
891 serial_outp(up, UART_LCR, cval); /* reset DLAB */
892 up->lcr = cval; /* Save LCR */
893 if (up->port.type != PORT_16750) {
894 if (fcr & UART_FCR_ENABLE_FIFO) {
895 /* emulated UARTs (Lucent Venus 167x) need two steps */
896 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
897 }
898 serial_outp(up, UART_FCR, fcr); /* set fcr */
899 }
900
901 up->cflag = cflag;
902
903 spin_unlock_irqrestore(&up->port.lock, flags);
904}
905
906static void
907sunsu_set_termios(struct uart_port *port, struct ktermios *termios,
908 struct ktermios *old)
909{
910 unsigned int baud, quot;
911
912 /*
913 * Ask the core to calculate the divisor for us.
914 */
915 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
916 quot = uart_get_divisor(port, baud);
917
918 sunsu_change_speed(port, termios->c_cflag, termios->c_iflag, quot);
919}
920
921static void sunsu_release_port(struct uart_port *port)
922{
923}
924
925static int sunsu_request_port(struct uart_port *port)
926{
927 return 0;
928}
929
930static void sunsu_config_port(struct uart_port *port, int flags)
931{
932 struct uart_sunsu_port *up =
933 container_of(port, struct uart_sunsu_port, port);
934
935 if (flags & UART_CONFIG_TYPE) {
936 /*
937 * We are supposed to call autoconfig here, but this requires
938 * splitting all the OBP probing crap from the UART probing.
939 * We'll do it when we kill sunsu.c altogether.
940 */
941 port->type = up->type_probed; /* XXX */
942 }
943}
944
945static int
946sunsu_verify_port(struct uart_port *port, struct serial_struct *ser)
947{
948 return -EINVAL;
949}
950
951static const char *
952sunsu_type(struct uart_port *port)
953{
954 int type = port->type;
955
956 if (type >= ARRAY_SIZE(uart_config))
957 type = 0;
958 return uart_config[type].name;
959}
960
961static struct uart_ops sunsu_pops = {
962 .tx_empty = sunsu_tx_empty,
963 .set_mctrl = sunsu_set_mctrl,
964 .get_mctrl = sunsu_get_mctrl,
965 .stop_tx = sunsu_stop_tx,
966 .start_tx = sunsu_start_tx,
967 .stop_rx = sunsu_stop_rx,
968 .enable_ms = sunsu_enable_ms,
969 .break_ctl = sunsu_break_ctl,
970 .startup = sunsu_startup,
971 .shutdown = sunsu_shutdown,
972 .set_termios = sunsu_set_termios,
973 .type = sunsu_type,
974 .release_port = sunsu_release_port,
975 .request_port = sunsu_request_port,
976 .config_port = sunsu_config_port,
977 .verify_port = sunsu_verify_port,
978};
979
980#define UART_NR 4
981
982static struct uart_sunsu_port sunsu_ports[UART_NR];
983static int nr_inst; /* Number of already registered ports */
984
985#ifdef CONFIG_SERIO
986
987static DEFINE_SPINLOCK(sunsu_serio_lock);
988
989static int sunsu_serio_write(struct serio *serio, unsigned char ch)
990{
991 struct uart_sunsu_port *up = serio->port_data;
992 unsigned long flags;
993 int lsr;
994
995 spin_lock_irqsave(&sunsu_serio_lock, flags);
996
997 do {
998 lsr = serial_in(up, UART_LSR);
999 } while (!(lsr & UART_LSR_THRE));
1000
1001 /* Send the character out. */
1002 serial_out(up, UART_TX, ch);
1003
1004 spin_unlock_irqrestore(&sunsu_serio_lock, flags);
1005
1006 return 0;
1007}
1008
1009static int sunsu_serio_open(struct serio *serio)
1010{
1011 struct uart_sunsu_port *up = serio->port_data;
1012 unsigned long flags;
1013 int ret;
1014
1015 spin_lock_irqsave(&sunsu_serio_lock, flags);
1016 if (!up->serio_open) {
1017 up->serio_open = 1;
1018 ret = 0;
1019 } else
1020 ret = -EBUSY;
1021 spin_unlock_irqrestore(&sunsu_serio_lock, flags);
1022
1023 return ret;
1024}
1025
1026static void sunsu_serio_close(struct serio *serio)
1027{
1028 struct uart_sunsu_port *up = serio->port_data;
1029 unsigned long flags;
1030
1031 spin_lock_irqsave(&sunsu_serio_lock, flags);
1032 up->serio_open = 0;
1033 spin_unlock_irqrestore(&sunsu_serio_lock, flags);
1034}
1035
1036#endif /* CONFIG_SERIO */
1037
1038static void sunsu_autoconfig(struct uart_sunsu_port *up)
1039{
1040 unsigned char status1, status2, scratch, scratch2, scratch3;
1041 unsigned char save_lcr, save_mcr;
1042 unsigned long flags;
1043
1044 if (up->su_type == SU_PORT_NONE)
1045 return;
1046
1047 up->type_probed = PORT_UNKNOWN;
1048 up->port.iotype = UPIO_MEM;
1049
1050 spin_lock_irqsave(&up->port.lock, flags);
1051
1052 if (!(up->port.flags & UPF_BUGGY_UART)) {
1053 /*
1054 * Do a simple existence test first; if we fail this, there's
1055 * no point trying anything else.
1056 *
1057 * 0x80 is used as a nonsense port to prevent against false
1058 * positives due to ISA bus float. The assumption is that
1059 * 0x80 is a non-existent port; which should be safe since
1060 * include/asm/io.h also makes this assumption.
1061 */
1062 scratch = serial_inp(up, UART_IER);
1063 serial_outp(up, UART_IER, 0);
1064#ifdef __i386__
1065 outb(0xff, 0x080);
1066#endif
1067 scratch2 = serial_inp(up, UART_IER);
1068 serial_outp(up, UART_IER, 0x0f);
1069#ifdef __i386__
1070 outb(0, 0x080);
1071#endif
1072 scratch3 = serial_inp(up, UART_IER);
1073 serial_outp(up, UART_IER, scratch);
1074 if (scratch2 != 0 || scratch3 != 0x0F)
1075 goto out; /* We failed; there's nothing here */
1076 }
1077
1078 save_mcr = serial_in(up, UART_MCR);
1079 save_lcr = serial_in(up, UART_LCR);
1080
1081 /*
1082 * Check to see if a UART is really there. Certain broken
1083 * internal modems based on the Rockwell chipset fail this
1084 * test, because they apparently don't implement the loopback
1085 * test mode. So this test is skipped on the COM 1 through
1086 * COM 4 ports. This *should* be safe, since no board
1087 * manufacturer would be stupid enough to design a board
1088 * that conflicts with COM 1-4 --- we hope!
1089 */
1090 if (!(up->port.flags & UPF_SKIP_TEST)) {
1091 serial_outp(up, UART_MCR, UART_MCR_LOOP | 0x0A);
1092 status1 = serial_inp(up, UART_MSR) & 0xF0;
1093 serial_outp(up, UART_MCR, save_mcr);
1094 if (status1 != 0x90)
1095 goto out; /* We failed loopback test */
1096 }
1097 serial_outp(up, UART_LCR, 0xBF); /* set up for StarTech test */
1098 serial_outp(up, UART_EFR, 0); /* EFR is the same as FCR */
1099 serial_outp(up, UART_LCR, 0);
1100 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
1101 scratch = serial_in(up, UART_IIR) >> 6;
1102 switch (scratch) {
1103 case 0:
1104 up->port.type = PORT_16450;
1105 break;
1106 case 1:
1107 up->port.type = PORT_UNKNOWN;
1108 break;
1109 case 2:
1110 up->port.type = PORT_16550;
1111 break;
1112 case 3:
1113 up->port.type = PORT_16550A;
1114 break;
1115 }
1116 if (up->port.type == PORT_16550A) {
1117 /* Check for Startech UART's */
1118 serial_outp(up, UART_LCR, UART_LCR_DLAB);
1119 if (serial_in(up, UART_EFR) == 0) {
1120 up->port.type = PORT_16650;
1121 } else {
1122 serial_outp(up, UART_LCR, 0xBF);
1123 if (serial_in(up, UART_EFR) == 0)
1124 up->port.type = PORT_16650V2;
1125 }
1126 }
1127 if (up->port.type == PORT_16550A) {
1128 /* Check for TI 16750 */
1129 serial_outp(up, UART_LCR, save_lcr | UART_LCR_DLAB);
1130 serial_outp(up, UART_FCR,
1131 UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
1132 scratch = serial_in(up, UART_IIR) >> 5;
1133 if (scratch == 7) {
1134 /*
1135 * If this is a 16750, and not a cheap UART
1136 * clone, then it should only go into 64 byte
1137 * mode if the UART_FCR7_64BYTE bit was set
1138 * while UART_LCR_DLAB was latched.
1139 */
1140 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
1141 serial_outp(up, UART_LCR, 0);
1142 serial_outp(up, UART_FCR,
1143 UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
1144 scratch = serial_in(up, UART_IIR) >> 5;
1145 if (scratch == 6)
1146 up->port.type = PORT_16750;
1147 }
1148 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
1149 }
1150 serial_outp(up, UART_LCR, save_lcr);
1151 if (up->port.type == PORT_16450) {
1152 scratch = serial_in(up, UART_SCR);
1153 serial_outp(up, UART_SCR, 0xa5);
1154 status1 = serial_in(up, UART_SCR);
1155 serial_outp(up, UART_SCR, 0x5a);
1156 status2 = serial_in(up, UART_SCR);
1157 serial_outp(up, UART_SCR, scratch);
1158
1159 if ((status1 != 0xa5) || (status2 != 0x5a))
1160 up->port.type = PORT_8250;
1161 }
1162
1163 up->port.fifosize = uart_config[up->port.type].dfl_xmit_fifo_size;
1164
1165 if (up->port.type == PORT_UNKNOWN)
1166 goto out;
1167 up->type_probed = up->port.type; /* XXX */
1168
1169 /*
1170 * Reset the UART.
1171 */
1172#ifdef CONFIG_SERIAL_8250_RSA
1173 if (up->port.type == PORT_RSA)
1174 serial_outp(up, UART_RSA_FRR, 0);
1175#endif
1176 serial_outp(up, UART_MCR, save_mcr);
1177 serial_outp(up, UART_FCR, (UART_FCR_ENABLE_FIFO |
1178 UART_FCR_CLEAR_RCVR |
1179 UART_FCR_CLEAR_XMIT));
1180 serial_outp(up, UART_FCR, 0);
1181 (void)serial_in(up, UART_RX);
1182 serial_outp(up, UART_IER, 0);
1183
1184out:
1185 spin_unlock_irqrestore(&up->port.lock, flags);
1186}
1187
1188static struct uart_driver sunsu_reg = {
1189 .owner = THIS_MODULE,
1190 .driver_name = "sunsu",
1191 .dev_name = "ttyS",
1192 .major = TTY_MAJOR,
1193};
1194
1195static int sunsu_kbd_ms_init(struct uart_sunsu_port *up)
1196{
1197 int quot, baud;
1198#ifdef CONFIG_SERIO
1199 struct serio *serio;
1200#endif
1201
1202 if (up->su_type == SU_PORT_KBD) {
1203 up->cflag = B1200 | CS8 | CLOCAL | CREAD;
1204 baud = 1200;
1205 } else {
1206 up->cflag = B4800 | CS8 | CLOCAL | CREAD;
1207 baud = 4800;
1208 }
1209 quot = up->port.uartclk / (16 * baud);
1210
1211 sunsu_autoconfig(up);
1212 if (up->port.type == PORT_UNKNOWN)
1213 return -ENODEV;
1214
1215 printk("%s: %s port at %llx, irq %u\n",
1216 up->port.dev->of_node->full_name,
1217 (up->su_type == SU_PORT_KBD) ? "Keyboard" : "Mouse",
1218 (unsigned long long) up->port.mapbase,
1219 up->port.irq);
1220
1221#ifdef CONFIG_SERIO
1222 serio = &up->serio;
1223 serio->port_data = up;
1224
1225 serio->id.type = SERIO_RS232;
1226 if (up->su_type == SU_PORT_KBD) {
1227 serio->id.proto = SERIO_SUNKBD;
1228 strlcpy(serio->name, "sukbd", sizeof(serio->name));
1229 } else {
1230 serio->id.proto = SERIO_SUN;
1231 serio->id.extra = 1;
1232 strlcpy(serio->name, "sums", sizeof(serio->name));
1233 }
1234 strlcpy(serio->phys,
1235 (!(up->port.line & 1) ? "su/serio0" : "su/serio1"),
1236 sizeof(serio->phys));
1237
1238 serio->write = sunsu_serio_write;
1239 serio->open = sunsu_serio_open;
1240 serio->close = sunsu_serio_close;
1241 serio->dev.parent = up->port.dev;
1242
1243 serio_register_port(serio);
1244#endif
1245
1246 sunsu_change_speed(&up->port, up->cflag, 0, quot);
1247
1248 sunsu_startup(&up->port);
1249 return 0;
1250}
1251
1252/*
1253 * ------------------------------------------------------------
1254 * Serial console driver
1255 * ------------------------------------------------------------
1256 */
1257
1258#ifdef CONFIG_SERIAL_SUNSU_CONSOLE
1259
1260#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
1261
1262/*
1263 * Wait for transmitter & holding register to empty
1264 */
1265static void wait_for_xmitr(struct uart_sunsu_port *up)
1266{
1267 unsigned int status, tmout = 10000;
1268
1269 /* Wait up to 10ms for the character(s) to be sent. */
1270 do {
1271 status = serial_in(up, UART_LSR);
1272
1273 if (status & UART_LSR_BI)
1274 up->lsr_break_flag = UART_LSR_BI;
1275
1276 if (--tmout == 0)
1277 break;
1278 udelay(1);
1279 } while ((status & BOTH_EMPTY) != BOTH_EMPTY);
1280
1281 /* Wait up to 1s for flow control if necessary */
1282 if (up->port.flags & UPF_CONS_FLOW) {
1283 tmout = 1000000;
1284 while (--tmout &&
1285 ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0))
1286 udelay(1);
1287 }
1288}
1289
1290static void sunsu_console_putchar(struct uart_port *port, int ch)
1291{
1292 struct uart_sunsu_port *up =
1293 container_of(port, struct uart_sunsu_port, port);
1294
1295 wait_for_xmitr(up);
1296 serial_out(up, UART_TX, ch);
1297}
1298
1299/*
1300 * Print a string to the serial port trying not to disturb
1301 * any possible real use of the port...
1302 */
1303static void sunsu_console_write(struct console *co, const char *s,
1304 unsigned int count)
1305{
1306 struct uart_sunsu_port *up = &sunsu_ports[co->index];
1307 unsigned long flags;
1308 unsigned int ier;
1309 int locked = 1;
1310
1311 if (up->port.sysrq || oops_in_progress)
1312 locked = spin_trylock_irqsave(&up->port.lock, flags);
1313 else
1314 spin_lock_irqsave(&up->port.lock, flags);
1315
1316 /*
1317 * First save the UER then disable the interrupts
1318 */
1319 ier = serial_in(up, UART_IER);
1320 serial_out(up, UART_IER, 0);
1321
1322 uart_console_write(&up->port, s, count, sunsu_console_putchar);
1323
1324 /*
1325 * Finally, wait for transmitter to become empty
1326 * and restore the IER
1327 */
1328 wait_for_xmitr(up);
1329 serial_out(up, UART_IER, ier);
1330
1331 if (locked)
1332 spin_unlock_irqrestore(&up->port.lock, flags);
1333}
1334
1335/*
1336 * Setup initial baud/bits/parity. We do two things here:
1337 * - construct a cflag setting for the first su_open()
1338 * - initialize the serial port
1339 * Return non-zero if we didn't find a serial port.
1340 */
1341static int __init sunsu_console_setup(struct console *co, char *options)
1342{
1343 static struct ktermios dummy;
1344 struct ktermios termios;
1345 struct uart_port *port;
1346
1347 printk("Console: ttyS%d (SU)\n",
1348 (sunsu_reg.minor - 64) + co->index);
1349
1350 if (co->index > nr_inst)
1351 return -ENODEV;
1352 port = &sunsu_ports[co->index].port;
1353
1354 /*
1355 * Temporary fix.
1356 */
1357 spin_lock_init(&port->lock);
1358
1359 /* Get firmware console settings. */
1360 sunserial_console_termios(co, port->dev->of_node);
1361
1362 memset(&termios, 0, sizeof(struct ktermios));
1363 termios.c_cflag = co->cflag;
1364 port->mctrl |= TIOCM_DTR;
1365 port->ops->set_termios(port, &termios, &dummy);
1366
1367 return 0;
1368}
1369
1370static struct console sunsu_console = {
1371 .name = "ttyS",
1372 .write = sunsu_console_write,
1373 .device = uart_console_device,
1374 .setup = sunsu_console_setup,
1375 .flags = CON_PRINTBUFFER,
1376 .index = -1,
1377 .data = &sunsu_reg,
1378};
1379
1380/*
1381 * Register console.
1382 */
1383
1384static inline struct console *SUNSU_CONSOLE(void)
1385{
1386 return &sunsu_console;
1387}
1388#else
1389#define SUNSU_CONSOLE() (NULL)
1390#define sunsu_serial_console_init() do { } while (0)
1391#endif
1392
1393static enum su_type su_get_type(struct device_node *dp)
1394{
1395 struct device_node *ap = of_find_node_by_path("/aliases");
1396
1397 if (ap) {
1398 const char *keyb = of_get_property(ap, "keyboard", NULL);
1399 const char *ms = of_get_property(ap, "mouse", NULL);
1400
1401 if (keyb) {
1402 if (dp == of_find_node_by_path(keyb))
1403 return SU_PORT_KBD;
1404 }
1405 if (ms) {
1406 if (dp == of_find_node_by_path(ms))
1407 return SU_PORT_MS;
1408 }
1409 }
1410
1411 return SU_PORT_PORT;
1412}
1413
1414static int su_probe(struct platform_device *op)
1415{
1416 struct device_node *dp = op->dev.of_node;
1417 struct uart_sunsu_port *up;
1418 struct resource *rp;
1419 enum su_type type;
1420 bool ignore_line;
1421 int err;
1422
1423 type = su_get_type(dp);
1424 if (type == SU_PORT_PORT) {
1425 if (nr_inst >= UART_NR)
1426 return -EINVAL;
1427 up = &sunsu_ports[nr_inst];
1428 } else {
1429 up = kzalloc(sizeof(*up), GFP_KERNEL);
1430 if (!up)
1431 return -ENOMEM;
1432 }
1433
1434 up->port.line = nr_inst;
1435
1436 spin_lock_init(&up->port.lock);
1437
1438 up->su_type = type;
1439
1440 rp = &op->resource[0];
1441 up->port.mapbase = rp->start;
1442 up->reg_size = resource_size(rp);
1443 up->port.membase = of_ioremap(rp, 0, up->reg_size, "su");
1444 if (!up->port.membase) {
1445 if (type != SU_PORT_PORT)
1446 kfree(up);
1447 return -ENOMEM;
1448 }
1449
1450 up->port.irq = op->archdata.irqs[0];
1451
1452 up->port.dev = &op->dev;
1453
1454 up->port.type = PORT_UNKNOWN;
1455 up->port.uartclk = (SU_BASE_BAUD * 16);
1456
1457 err = 0;
1458 if (up->su_type == SU_PORT_KBD || up->su_type == SU_PORT_MS) {
1459 err = sunsu_kbd_ms_init(up);
1460 if (err) {
1461 of_iounmap(&op->resource[0],
1462 up->port.membase, up->reg_size);
1463 kfree(up);
1464 return err;
1465 }
1466 platform_set_drvdata(op, up);
1467
1468 nr_inst++;
1469
1470 return 0;
1471 }
1472
1473 up->port.flags |= UPF_BOOT_AUTOCONF;
1474
1475 sunsu_autoconfig(up);
1476
1477 err = -ENODEV;
1478 if (up->port.type == PORT_UNKNOWN)
1479 goto out_unmap;
1480
1481 up->port.ops = &sunsu_pops;
1482
1483 ignore_line = false;
1484 if (!strcmp(dp->name, "rsc-console") ||
1485 !strcmp(dp->name, "lom-console"))
1486 ignore_line = true;
1487
1488 sunserial_console_match(SUNSU_CONSOLE(), dp,
1489 &sunsu_reg, up->port.line,
1490 ignore_line);
1491 err = uart_add_one_port(&sunsu_reg, &up->port);
1492 if (err)
1493 goto out_unmap;
1494
1495 platform_set_drvdata(op, up);
1496
1497 nr_inst++;
1498
1499 return 0;
1500
1501out_unmap:
1502 of_iounmap(&op->resource[0], up->port.membase, up->reg_size);
1503 return err;
1504}
1505
1506static int su_remove(struct platform_device *op)
1507{
1508 struct uart_sunsu_port *up = platform_get_drvdata(op);
1509 bool kbdms = false;
1510
1511 if (up->su_type == SU_PORT_MS ||
1512 up->su_type == SU_PORT_KBD)
1513 kbdms = true;
1514
1515 if (kbdms) {
1516#ifdef CONFIG_SERIO
1517 serio_unregister_port(&up->serio);
1518#endif
1519 } else if (up->port.type != PORT_UNKNOWN)
1520 uart_remove_one_port(&sunsu_reg, &up->port);
1521
1522 if (up->port.membase)
1523 of_iounmap(&op->resource[0], up->port.membase, up->reg_size);
1524
1525 if (kbdms)
1526 kfree(up);
1527
1528 return 0;
1529}
1530
1531static const struct of_device_id su_match[] = {
1532 {
1533 .name = "su",
1534 },
1535 {
1536 .name = "su_pnp",
1537 },
1538 {
1539 .name = "serial",
1540 .compatible = "su",
1541 },
1542 {
1543 .type = "serial",
1544 .compatible = "su",
1545 },
1546 {},
1547};
1548MODULE_DEVICE_TABLE(of, su_match);
1549
1550static struct platform_driver su_driver = {
1551 .driver = {
1552 .name = "su",
1553 .of_match_table = su_match,
1554 },
1555 .probe = su_probe,
1556 .remove = su_remove,
1557};
1558
1559static int __init sunsu_init(void)
1560{
1561 struct device_node *dp;
1562 int err;
1563 int num_uart = 0;
1564
1565 for_each_node_by_name(dp, "su") {
1566 if (su_get_type(dp) == SU_PORT_PORT)
1567 num_uart++;
1568 }
1569 for_each_node_by_name(dp, "su_pnp") {
1570 if (su_get_type(dp) == SU_PORT_PORT)
1571 num_uart++;
1572 }
1573 for_each_node_by_name(dp, "serial") {
1574 if (of_device_is_compatible(dp, "su")) {
1575 if (su_get_type(dp) == SU_PORT_PORT)
1576 num_uart++;
1577 }
1578 }
1579 for_each_node_by_type(dp, "serial") {
1580 if (of_device_is_compatible(dp, "su")) {
1581 if (su_get_type(dp) == SU_PORT_PORT)
1582 num_uart++;
1583 }
1584 }
1585
1586 if (num_uart) {
1587 err = sunserial_register_minors(&sunsu_reg, num_uart);
1588 if (err)
1589 return err;
1590 }
1591
1592 err = platform_driver_register(&su_driver);
1593 if (err && num_uart)
1594 sunserial_unregister_minors(&sunsu_reg, num_uart);
1595
1596 return err;
1597}
1598
1599static void __exit sunsu_exit(void)
1600{
1601 platform_driver_unregister(&su_driver);
1602 if (sunsu_reg.nr)
1603 sunserial_unregister_minors(&sunsu_reg, sunsu_reg.nr);
1604}
1605
1606module_init(sunsu_init);
1607module_exit(sunsu_exit);
1608
1609MODULE_AUTHOR("Eddie C. Dost, Peter Zaitcev, and David S. Miller");
1610MODULE_DESCRIPTION("Sun SU serial port driver");
1611MODULE_VERSION("2.0");
1612MODULE_LICENSE("GPL");