Loading...
Note: File does not exist in v4.17.
1/******************************************************************************
2 *
3 * This file is provided under a dual BSD/GPLv2 license. When using or
4 * redistributing this file, you may do so under either license.
5 *
6 * GPL LICENSE SUMMARY
7 *
8 * Copyright(c) 2005 - 2011 Intel Corporation. All rights reserved.
9 *
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of version 2 of the GNU General Public License as
12 * published by the Free Software Foundation.
13 *
14 * This program is distributed in the hope that it will be useful, but
15 * WITHOUT ANY WARRANTY; without even the implied warranty of
16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
17 * General Public License for more details.
18 *
19 * You should have received a copy of the GNU General Public License
20 * along with this program; if not, write to the Free Software
21 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110,
22 * USA
23 *
24 * The full GNU General Public License is included in this distribution
25 * in the file called LICENSE.GPL.
26 *
27 * Contact Information:
28 * Intel Linux Wireless <ilw@linux.intel.com>
29 * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
30 *
31 * BSD LICENSE
32 *
33 * Copyright(c) 2005 - 2011 Intel Corporation. All rights reserved.
34 * All rights reserved.
35 *
36 * Redistribution and use in source and binary forms, with or without
37 * modification, are permitted provided that the following conditions
38 * are met:
39 *
40 * * Redistributions of source code must retain the above copyright
41 * notice, this list of conditions and the following disclaimer.
42 * * Redistributions in binary form must reproduce the above copyright
43 * notice, this list of conditions and the following disclaimer in
44 * the documentation and/or other materials provided with the
45 * distribution.
46 * * Neither the name Intel Corporation nor the names of its
47 * contributors may be used to endorse or promote products derived
48 * from this software without specific prior written permission.
49 *
50 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
51 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
52 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
53 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
54 * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
55 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
56 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
57 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
58 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
59 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
60 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
61 *
62 *****************************************************************************/
63/*
64 * Please use this file (iwl-commands.h) only for uCode API definitions.
65 * Please use iwl-xxxx-hw.h for hardware-related definitions.
66 * Please use iwl-dev.h for driver implementation definitions.
67 */
68
69#ifndef __iwl_legacy_commands_h__
70#define __iwl_legacy_commands_h__
71
72struct iwl_priv;
73
74/* uCode version contains 4 values: Major/Minor/API/Serial */
75#define IWL_UCODE_MAJOR(ver) (((ver) & 0xFF000000) >> 24)
76#define IWL_UCODE_MINOR(ver) (((ver) & 0x00FF0000) >> 16)
77#define IWL_UCODE_API(ver) (((ver) & 0x0000FF00) >> 8)
78#define IWL_UCODE_SERIAL(ver) ((ver) & 0x000000FF)
79
80
81/* Tx rates */
82#define IWL_CCK_RATES 4
83#define IWL_OFDM_RATES 8
84#define IWL_MAX_RATES (IWL_CCK_RATES + IWL_OFDM_RATES)
85
86enum {
87 REPLY_ALIVE = 0x1,
88 REPLY_ERROR = 0x2,
89
90 /* RXON and QOS commands */
91 REPLY_RXON = 0x10,
92 REPLY_RXON_ASSOC = 0x11,
93 REPLY_QOS_PARAM = 0x13,
94 REPLY_RXON_TIMING = 0x14,
95
96 /* Multi-Station support */
97 REPLY_ADD_STA = 0x18,
98 REPLY_REMOVE_STA = 0x19,
99
100 /* Security */
101 REPLY_WEPKEY = 0x20,
102
103 /* RX, TX, LEDs */
104 REPLY_3945_RX = 0x1b, /* 3945 only */
105 REPLY_TX = 0x1c,
106 REPLY_RATE_SCALE = 0x47, /* 3945 only */
107 REPLY_LEDS_CMD = 0x48,
108 REPLY_TX_LINK_QUALITY_CMD = 0x4e, /* for 4965 and up */
109
110 /* 802.11h related */
111 REPLY_CHANNEL_SWITCH = 0x72,
112 CHANNEL_SWITCH_NOTIFICATION = 0x73,
113 REPLY_SPECTRUM_MEASUREMENT_CMD = 0x74,
114 SPECTRUM_MEASURE_NOTIFICATION = 0x75,
115
116 /* Power Management */
117 POWER_TABLE_CMD = 0x77,
118 PM_SLEEP_NOTIFICATION = 0x7A,
119 PM_DEBUG_STATISTIC_NOTIFIC = 0x7B,
120
121 /* Scan commands and notifications */
122 REPLY_SCAN_CMD = 0x80,
123 REPLY_SCAN_ABORT_CMD = 0x81,
124 SCAN_START_NOTIFICATION = 0x82,
125 SCAN_RESULTS_NOTIFICATION = 0x83,
126 SCAN_COMPLETE_NOTIFICATION = 0x84,
127
128 /* IBSS/AP commands */
129 BEACON_NOTIFICATION = 0x90,
130 REPLY_TX_BEACON = 0x91,
131
132 /* Miscellaneous commands */
133 REPLY_TX_PWR_TABLE_CMD = 0x97,
134
135 /* Bluetooth device coexistence config command */
136 REPLY_BT_CONFIG = 0x9b,
137
138 /* Statistics */
139 REPLY_STATISTICS_CMD = 0x9c,
140 STATISTICS_NOTIFICATION = 0x9d,
141
142 /* RF-KILL commands and notifications */
143 CARD_STATE_NOTIFICATION = 0xa1,
144
145 /* Missed beacons notification */
146 MISSED_BEACONS_NOTIFICATION = 0xa2,
147
148 REPLY_CT_KILL_CONFIG_CMD = 0xa4,
149 SENSITIVITY_CMD = 0xa8,
150 REPLY_PHY_CALIBRATION_CMD = 0xb0,
151 REPLY_RX_PHY_CMD = 0xc0,
152 REPLY_RX_MPDU_CMD = 0xc1,
153 REPLY_RX = 0xc3,
154 REPLY_COMPRESSED_BA = 0xc5,
155
156 REPLY_MAX = 0xff
157};
158
159/******************************************************************************
160 * (0)
161 * Commonly used structures and definitions:
162 * Command header, rate_n_flags, txpower
163 *
164 *****************************************************************************/
165
166/* iwl_cmd_header flags value */
167#define IWL_CMD_FAILED_MSK 0x40
168
169#define SEQ_TO_QUEUE(s) (((s) >> 8) & 0x1f)
170#define QUEUE_TO_SEQ(q) (((q) & 0x1f) << 8)
171#define SEQ_TO_INDEX(s) ((s) & 0xff)
172#define INDEX_TO_SEQ(i) ((i) & 0xff)
173#define SEQ_HUGE_FRAME cpu_to_le16(0x4000)
174#define SEQ_RX_FRAME cpu_to_le16(0x8000)
175
176/**
177 * struct iwl_cmd_header
178 *
179 * This header format appears in the beginning of each command sent from the
180 * driver, and each response/notification received from uCode.
181 */
182struct iwl_cmd_header {
183 u8 cmd; /* Command ID: REPLY_RXON, etc. */
184 u8 flags; /* 0:5 reserved, 6 abort, 7 internal */
185 /*
186 * The driver sets up the sequence number to values of its choosing.
187 * uCode does not use this value, but passes it back to the driver
188 * when sending the response to each driver-originated command, so
189 * the driver can match the response to the command. Since the values
190 * don't get used by uCode, the driver may set up an arbitrary format.
191 *
192 * There is one exception: uCode sets bit 15 when it originates
193 * the response/notification, i.e. when the response/notification
194 * is not a direct response to a command sent by the driver. For
195 * example, uCode issues REPLY_3945_RX when it sends a received frame
196 * to the driver; it is not a direct response to any driver command.
197 *
198 * The Linux driver uses the following format:
199 *
200 * 0:7 tfd index - position within TX queue
201 * 8:12 TX queue id
202 * 13 reserved
203 * 14 huge - driver sets this to indicate command is in the
204 * 'huge' storage at the end of the command buffers
205 * 15 unsolicited RX or uCode-originated notification
206 */
207 __le16 sequence;
208
209 /* command or response/notification data follows immediately */
210 u8 data[0];
211} __packed;
212
213
214/**
215 * struct iwl3945_tx_power
216 *
217 * Used in REPLY_TX_PWR_TABLE_CMD, REPLY_SCAN_CMD, REPLY_CHANNEL_SWITCH
218 *
219 * Each entry contains two values:
220 * 1) DSP gain (or sometimes called DSP attenuation). This is a fine-grained
221 * linear value that multiplies the output of the digital signal processor,
222 * before being sent to the analog radio.
223 * 2) Radio gain. This sets the analog gain of the radio Tx path.
224 * It is a coarser setting, and behaves in a logarithmic (dB) fashion.
225 *
226 * Driver obtains values from struct iwl3945_tx_power power_gain_table[][].
227 */
228struct iwl3945_tx_power {
229 u8 tx_gain; /* gain for analog radio */
230 u8 dsp_atten; /* gain for DSP */
231} __packed;
232
233/**
234 * struct iwl3945_power_per_rate
235 *
236 * Used in REPLY_TX_PWR_TABLE_CMD, REPLY_CHANNEL_SWITCH
237 */
238struct iwl3945_power_per_rate {
239 u8 rate; /* plcp */
240 struct iwl3945_tx_power tpc;
241 u8 reserved;
242} __packed;
243
244/**
245 * iwl4965 rate_n_flags bit fields
246 *
247 * rate_n_flags format is used in following iwl4965 commands:
248 * REPLY_RX (response only)
249 * REPLY_RX_MPDU (response only)
250 * REPLY_TX (both command and response)
251 * REPLY_TX_LINK_QUALITY_CMD
252 *
253 * High-throughput (HT) rate format for bits 7:0 (bit 8 must be "1"):
254 * 2-0: 0) 6 Mbps
255 * 1) 12 Mbps
256 * 2) 18 Mbps
257 * 3) 24 Mbps
258 * 4) 36 Mbps
259 * 5) 48 Mbps
260 * 6) 54 Mbps
261 * 7) 60 Mbps
262 *
263 * 4-3: 0) Single stream (SISO)
264 * 1) Dual stream (MIMO)
265 * 2) Triple stream (MIMO)
266 *
267 * 5: Value of 0x20 in bits 7:0 indicates 6 Mbps HT40 duplicate data
268 *
269 * Legacy OFDM rate format for bits 7:0 (bit 8 must be "0", bit 9 "0"):
270 * 3-0: 0xD) 6 Mbps
271 * 0xF) 9 Mbps
272 * 0x5) 12 Mbps
273 * 0x7) 18 Mbps
274 * 0x9) 24 Mbps
275 * 0xB) 36 Mbps
276 * 0x1) 48 Mbps
277 * 0x3) 54 Mbps
278 *
279 * Legacy CCK rate format for bits 7:0 (bit 8 must be "0", bit 9 "1"):
280 * 6-0: 10) 1 Mbps
281 * 20) 2 Mbps
282 * 55) 5.5 Mbps
283 * 110) 11 Mbps
284 */
285#define RATE_MCS_CODE_MSK 0x7
286#define RATE_MCS_SPATIAL_POS 3
287#define RATE_MCS_SPATIAL_MSK 0x18
288#define RATE_MCS_HT_DUP_POS 5
289#define RATE_MCS_HT_DUP_MSK 0x20
290
291/* Bit 8: (1) HT format, (0) legacy format in bits 7:0 */
292#define RATE_MCS_FLAGS_POS 8
293#define RATE_MCS_HT_POS 8
294#define RATE_MCS_HT_MSK 0x100
295
296/* Bit 9: (1) CCK, (0) OFDM. HT (bit 8) must be "0" for this bit to be valid */
297#define RATE_MCS_CCK_POS 9
298#define RATE_MCS_CCK_MSK 0x200
299
300/* Bit 10: (1) Use Green Field preamble */
301#define RATE_MCS_GF_POS 10
302#define RATE_MCS_GF_MSK 0x400
303
304/* Bit 11: (1) Use 40Mhz HT40 chnl width, (0) use 20 MHz legacy chnl width */
305#define RATE_MCS_HT40_POS 11
306#define RATE_MCS_HT40_MSK 0x800
307
308/* Bit 12: (1) Duplicate data on both 20MHz chnls. HT40 (bit 11) must be set. */
309#define RATE_MCS_DUP_POS 12
310#define RATE_MCS_DUP_MSK 0x1000
311
312/* Bit 13: (1) Short guard interval (0.4 usec), (0) normal GI (0.8 usec) */
313#define RATE_MCS_SGI_POS 13
314#define RATE_MCS_SGI_MSK 0x2000
315
316/**
317 * rate_n_flags Tx antenna masks
318 * 4965 has 2 transmitters
319 * bit14:16
320 */
321#define RATE_MCS_ANT_POS 14
322#define RATE_MCS_ANT_A_MSK 0x04000
323#define RATE_MCS_ANT_B_MSK 0x08000
324#define RATE_MCS_ANT_C_MSK 0x10000
325#define RATE_MCS_ANT_AB_MSK (RATE_MCS_ANT_A_MSK | RATE_MCS_ANT_B_MSK)
326#define RATE_MCS_ANT_ABC_MSK (RATE_MCS_ANT_AB_MSK | RATE_MCS_ANT_C_MSK)
327#define RATE_ANT_NUM 3
328
329#define POWER_TABLE_NUM_ENTRIES 33
330#define POWER_TABLE_NUM_HT_OFDM_ENTRIES 32
331#define POWER_TABLE_CCK_ENTRY 32
332
333#define IWL_PWR_NUM_HT_OFDM_ENTRIES 24
334#define IWL_PWR_CCK_ENTRIES 2
335
336/**
337 * union iwl4965_tx_power_dual_stream
338 *
339 * Host format used for REPLY_TX_PWR_TABLE_CMD, REPLY_CHANNEL_SWITCH
340 * Use __le32 version (struct tx_power_dual_stream) when building command.
341 *
342 * Driver provides radio gain and DSP attenuation settings to device in pairs,
343 * one value for each transmitter chain. The first value is for transmitter A,
344 * second for transmitter B.
345 *
346 * For SISO bit rates, both values in a pair should be identical.
347 * For MIMO rates, one value may be different from the other,
348 * in order to balance the Tx output between the two transmitters.
349 *
350 * See more details in doc for TXPOWER in iwl-4965-hw.h.
351 */
352union iwl4965_tx_power_dual_stream {
353 struct {
354 u8 radio_tx_gain[2];
355 u8 dsp_predis_atten[2];
356 } s;
357 u32 dw;
358};
359
360/**
361 * struct tx_power_dual_stream
362 *
363 * Table entries in REPLY_TX_PWR_TABLE_CMD, REPLY_CHANNEL_SWITCH
364 *
365 * Same format as iwl_tx_power_dual_stream, but __le32
366 */
367struct tx_power_dual_stream {
368 __le32 dw;
369} __packed;
370
371/**
372 * struct iwl4965_tx_power_db
373 *
374 * Entire table within REPLY_TX_PWR_TABLE_CMD, REPLY_CHANNEL_SWITCH
375 */
376struct iwl4965_tx_power_db {
377 struct tx_power_dual_stream power_tbl[POWER_TABLE_NUM_ENTRIES];
378} __packed;
379
380/******************************************************************************
381 * (0a)
382 * Alive and Error Commands & Responses:
383 *
384 *****************************************************************************/
385
386#define UCODE_VALID_OK cpu_to_le32(0x1)
387#define INITIALIZE_SUBTYPE (9)
388
389/*
390 * ("Initialize") REPLY_ALIVE = 0x1 (response only, not a command)
391 *
392 * uCode issues this "initialize alive" notification once the initialization
393 * uCode image has completed its work, and is ready to load the runtime image.
394 * This is the *first* "alive" notification that the driver will receive after
395 * rebooting uCode; the "initialize" alive is indicated by subtype field == 9.
396 *
397 * See comments documenting "BSM" (bootstrap state machine).
398 *
399 * For 4965, this notification contains important calibration data for
400 * calculating txpower settings:
401 *
402 * 1) Power supply voltage indication. The voltage sensor outputs higher
403 * values for lower voltage, and vice verse.
404 *
405 * 2) Temperature measurement parameters, for each of two channel widths
406 * (20 MHz and 40 MHz) supported by the radios. Temperature sensing
407 * is done via one of the receiver chains, and channel width influences
408 * the results.
409 *
410 * 3) Tx gain compensation to balance 4965's 2 Tx chains for MIMO operation,
411 * for each of 5 frequency ranges.
412 */
413struct iwl_init_alive_resp {
414 u8 ucode_minor;
415 u8 ucode_major;
416 __le16 reserved1;
417 u8 sw_rev[8];
418 u8 ver_type;
419 u8 ver_subtype; /* "9" for initialize alive */
420 __le16 reserved2;
421 __le32 log_event_table_ptr;
422 __le32 error_event_table_ptr;
423 __le32 timestamp;
424 __le32 is_valid;
425
426 /* calibration values from "initialize" uCode */
427 __le32 voltage; /* signed, higher value is lower voltage */
428 __le32 therm_r1[2]; /* signed, 1st for normal, 2nd for HT40 */
429 __le32 therm_r2[2]; /* signed */
430 __le32 therm_r3[2]; /* signed */
431 __le32 therm_r4[2]; /* signed */
432 __le32 tx_atten[5][2]; /* signed MIMO gain comp, 5 freq groups,
433 * 2 Tx chains */
434} __packed;
435
436
437/**
438 * REPLY_ALIVE = 0x1 (response only, not a command)
439 *
440 * uCode issues this "alive" notification once the runtime image is ready
441 * to receive commands from the driver. This is the *second* "alive"
442 * notification that the driver will receive after rebooting uCode;
443 * this "alive" is indicated by subtype field != 9.
444 *
445 * See comments documenting "BSM" (bootstrap state machine).
446 *
447 * This response includes two pointers to structures within the device's
448 * data SRAM (access via HBUS_TARG_MEM_* regs) that are useful for debugging:
449 *
450 * 1) log_event_table_ptr indicates base of the event log. This traces
451 * a 256-entry history of uCode execution within a circular buffer.
452 * Its header format is:
453 *
454 * __le32 log_size; log capacity (in number of entries)
455 * __le32 type; (1) timestamp with each entry, (0) no timestamp
456 * __le32 wraps; # times uCode has wrapped to top of circular buffer
457 * __le32 write_index; next circular buffer entry that uCode would fill
458 *
459 * The header is followed by the circular buffer of log entries. Entries
460 * with timestamps have the following format:
461 *
462 * __le32 event_id; range 0 - 1500
463 * __le32 timestamp; low 32 bits of TSF (of network, if associated)
464 * __le32 data; event_id-specific data value
465 *
466 * Entries without timestamps contain only event_id and data.
467 *
468 *
469 * 2) error_event_table_ptr indicates base of the error log. This contains
470 * information about any uCode error that occurs. For 4965, the format
471 * of the error log is:
472 *
473 * __le32 valid; (nonzero) valid, (0) log is empty
474 * __le32 error_id; type of error
475 * __le32 pc; program counter
476 * __le32 blink1; branch link
477 * __le32 blink2; branch link
478 * __le32 ilink1; interrupt link
479 * __le32 ilink2; interrupt link
480 * __le32 data1; error-specific data
481 * __le32 data2; error-specific data
482 * __le32 line; source code line of error
483 * __le32 bcon_time; beacon timer
484 * __le32 tsf_low; network timestamp function timer
485 * __le32 tsf_hi; network timestamp function timer
486 * __le32 gp1; GP1 timer register
487 * __le32 gp2; GP2 timer register
488 * __le32 gp3; GP3 timer register
489 * __le32 ucode_ver; uCode version
490 * __le32 hw_ver; HW Silicon version
491 * __le32 brd_ver; HW board version
492 * __le32 log_pc; log program counter
493 * __le32 frame_ptr; frame pointer
494 * __le32 stack_ptr; stack pointer
495 * __le32 hcmd; last host command
496 * __le32 isr0; isr status register LMPM_NIC_ISR0: rxtx_flag
497 * __le32 isr1; isr status register LMPM_NIC_ISR1: host_flag
498 * __le32 isr2; isr status register LMPM_NIC_ISR2: enc_flag
499 * __le32 isr3; isr status register LMPM_NIC_ISR3: time_flag
500 * __le32 isr4; isr status register LMPM_NIC_ISR4: wico interrupt
501 * __le32 isr_pref; isr status register LMPM_NIC_PREF_STAT
502 * __le32 wait_event; wait event() caller address
503 * __le32 l2p_control; L2pControlField
504 * __le32 l2p_duration; L2pDurationField
505 * __le32 l2p_mhvalid; L2pMhValidBits
506 * __le32 l2p_addr_match; L2pAddrMatchStat
507 * __le32 lmpm_pmg_sel; indicate which clocks are turned on (LMPM_PMG_SEL)
508 * __le32 u_timestamp; indicate when the date and time of the compilation
509 * __le32 reserved;
510 *
511 * The Linux driver can print both logs to the system log when a uCode error
512 * occurs.
513 */
514struct iwl_alive_resp {
515 u8 ucode_minor;
516 u8 ucode_major;
517 __le16 reserved1;
518 u8 sw_rev[8];
519 u8 ver_type;
520 u8 ver_subtype; /* not "9" for runtime alive */
521 __le16 reserved2;
522 __le32 log_event_table_ptr; /* SRAM address for event log */
523 __le32 error_event_table_ptr; /* SRAM address for error log */
524 __le32 timestamp;
525 __le32 is_valid;
526} __packed;
527
528/*
529 * REPLY_ERROR = 0x2 (response only, not a command)
530 */
531struct iwl_error_resp {
532 __le32 error_type;
533 u8 cmd_id;
534 u8 reserved1;
535 __le16 bad_cmd_seq_num;
536 __le32 error_info;
537 __le64 timestamp;
538} __packed;
539
540/******************************************************************************
541 * (1)
542 * RXON Commands & Responses:
543 *
544 *****************************************************************************/
545
546/*
547 * Rx config defines & structure
548 */
549/* rx_config device types */
550enum {
551 RXON_DEV_TYPE_AP = 1,
552 RXON_DEV_TYPE_ESS = 3,
553 RXON_DEV_TYPE_IBSS = 4,
554 RXON_DEV_TYPE_SNIFFER = 6,
555};
556
557
558#define RXON_RX_CHAIN_DRIVER_FORCE_MSK cpu_to_le16(0x1 << 0)
559#define RXON_RX_CHAIN_DRIVER_FORCE_POS (0)
560#define RXON_RX_CHAIN_VALID_MSK cpu_to_le16(0x7 << 1)
561#define RXON_RX_CHAIN_VALID_POS (1)
562#define RXON_RX_CHAIN_FORCE_SEL_MSK cpu_to_le16(0x7 << 4)
563#define RXON_RX_CHAIN_FORCE_SEL_POS (4)
564#define RXON_RX_CHAIN_FORCE_MIMO_SEL_MSK cpu_to_le16(0x7 << 7)
565#define RXON_RX_CHAIN_FORCE_MIMO_SEL_POS (7)
566#define RXON_RX_CHAIN_CNT_MSK cpu_to_le16(0x3 << 10)
567#define RXON_RX_CHAIN_CNT_POS (10)
568#define RXON_RX_CHAIN_MIMO_CNT_MSK cpu_to_le16(0x3 << 12)
569#define RXON_RX_CHAIN_MIMO_CNT_POS (12)
570#define RXON_RX_CHAIN_MIMO_FORCE_MSK cpu_to_le16(0x1 << 14)
571#define RXON_RX_CHAIN_MIMO_FORCE_POS (14)
572
573/* rx_config flags */
574/* band & modulation selection */
575#define RXON_FLG_BAND_24G_MSK cpu_to_le32(1 << 0)
576#define RXON_FLG_CCK_MSK cpu_to_le32(1 << 1)
577/* auto detection enable */
578#define RXON_FLG_AUTO_DETECT_MSK cpu_to_le32(1 << 2)
579/* TGg protection when tx */
580#define RXON_FLG_TGG_PROTECT_MSK cpu_to_le32(1 << 3)
581/* cck short slot & preamble */
582#define RXON_FLG_SHORT_SLOT_MSK cpu_to_le32(1 << 4)
583#define RXON_FLG_SHORT_PREAMBLE_MSK cpu_to_le32(1 << 5)
584/* antenna selection */
585#define RXON_FLG_DIS_DIV_MSK cpu_to_le32(1 << 7)
586#define RXON_FLG_ANT_SEL_MSK cpu_to_le32(0x0f00)
587#define RXON_FLG_ANT_A_MSK cpu_to_le32(1 << 8)
588#define RXON_FLG_ANT_B_MSK cpu_to_le32(1 << 9)
589/* radar detection enable */
590#define RXON_FLG_RADAR_DETECT_MSK cpu_to_le32(1 << 12)
591#define RXON_FLG_TGJ_NARROW_BAND_MSK cpu_to_le32(1 << 13)
592/* rx response to host with 8-byte TSF
593* (according to ON_AIR deassertion) */
594#define RXON_FLG_TSF2HOST_MSK cpu_to_le32(1 << 15)
595
596
597/* HT flags */
598#define RXON_FLG_CTRL_CHANNEL_LOC_POS (22)
599#define RXON_FLG_CTRL_CHANNEL_LOC_HI_MSK cpu_to_le32(0x1 << 22)
600
601#define RXON_FLG_HT_OPERATING_MODE_POS (23)
602
603#define RXON_FLG_HT_PROT_MSK cpu_to_le32(0x1 << 23)
604#define RXON_FLG_HT40_PROT_MSK cpu_to_le32(0x2 << 23)
605
606#define RXON_FLG_CHANNEL_MODE_POS (25)
607#define RXON_FLG_CHANNEL_MODE_MSK cpu_to_le32(0x3 << 25)
608
609/* channel mode */
610enum {
611 CHANNEL_MODE_LEGACY = 0,
612 CHANNEL_MODE_PURE_40 = 1,
613 CHANNEL_MODE_MIXED = 2,
614 CHANNEL_MODE_RESERVED = 3,
615};
616#define RXON_FLG_CHANNEL_MODE_LEGACY \
617 cpu_to_le32(CHANNEL_MODE_LEGACY << RXON_FLG_CHANNEL_MODE_POS)
618#define RXON_FLG_CHANNEL_MODE_PURE_40 \
619 cpu_to_le32(CHANNEL_MODE_PURE_40 << RXON_FLG_CHANNEL_MODE_POS)
620#define RXON_FLG_CHANNEL_MODE_MIXED \
621 cpu_to_le32(CHANNEL_MODE_MIXED << RXON_FLG_CHANNEL_MODE_POS)
622
623/* CTS to self (if spec allows) flag */
624#define RXON_FLG_SELF_CTS_EN cpu_to_le32(0x1<<30)
625
626/* rx_config filter flags */
627/* accept all data frames */
628#define RXON_FILTER_PROMISC_MSK cpu_to_le32(1 << 0)
629/* pass control & management to host */
630#define RXON_FILTER_CTL2HOST_MSK cpu_to_le32(1 << 1)
631/* accept multi-cast */
632#define RXON_FILTER_ACCEPT_GRP_MSK cpu_to_le32(1 << 2)
633/* don't decrypt uni-cast frames */
634#define RXON_FILTER_DIS_DECRYPT_MSK cpu_to_le32(1 << 3)
635/* don't decrypt multi-cast frames */
636#define RXON_FILTER_DIS_GRP_DECRYPT_MSK cpu_to_le32(1 << 4)
637/* STA is associated */
638#define RXON_FILTER_ASSOC_MSK cpu_to_le32(1 << 5)
639/* transfer to host non bssid beacons in associated state */
640#define RXON_FILTER_BCON_AWARE_MSK cpu_to_le32(1 << 6)
641
642/**
643 * REPLY_RXON = 0x10 (command, has simple generic response)
644 *
645 * RXON tunes the radio tuner to a service channel, and sets up a number
646 * of parameters that are used primarily for Rx, but also for Tx operations.
647 *
648 * NOTE: When tuning to a new channel, driver must set the
649 * RXON_FILTER_ASSOC_MSK to 0. This will clear station-dependent
650 * info within the device, including the station tables, tx retry
651 * rate tables, and txpower tables. Driver must build a new station
652 * table and txpower table before transmitting anything on the RXON
653 * channel.
654 *
655 * NOTE: All RXONs wipe clean the internal txpower table. Driver must
656 * issue a new REPLY_TX_PWR_TABLE_CMD after each REPLY_RXON (0x10),
657 * regardless of whether RXON_FILTER_ASSOC_MSK is set.
658 */
659
660struct iwl3945_rxon_cmd {
661 u8 node_addr[6];
662 __le16 reserved1;
663 u8 bssid_addr[6];
664 __le16 reserved2;
665 u8 wlap_bssid_addr[6];
666 __le16 reserved3;
667 u8 dev_type;
668 u8 air_propagation;
669 __le16 reserved4;
670 u8 ofdm_basic_rates;
671 u8 cck_basic_rates;
672 __le16 assoc_id;
673 __le32 flags;
674 __le32 filter_flags;
675 __le16 channel;
676 __le16 reserved5;
677} __packed;
678
679struct iwl4965_rxon_cmd {
680 u8 node_addr[6];
681 __le16 reserved1;
682 u8 bssid_addr[6];
683 __le16 reserved2;
684 u8 wlap_bssid_addr[6];
685 __le16 reserved3;
686 u8 dev_type;
687 u8 air_propagation;
688 __le16 rx_chain;
689 u8 ofdm_basic_rates;
690 u8 cck_basic_rates;
691 __le16 assoc_id;
692 __le32 flags;
693 __le32 filter_flags;
694 __le16 channel;
695 u8 ofdm_ht_single_stream_basic_rates;
696 u8 ofdm_ht_dual_stream_basic_rates;
697} __packed;
698
699/* Create a common rxon cmd which will be typecast into the 3945 or 4965
700 * specific rxon cmd, depending on where it is called from.
701 */
702struct iwl_legacy_rxon_cmd {
703 u8 node_addr[6];
704 __le16 reserved1;
705 u8 bssid_addr[6];
706 __le16 reserved2;
707 u8 wlap_bssid_addr[6];
708 __le16 reserved3;
709 u8 dev_type;
710 u8 air_propagation;
711 __le16 rx_chain;
712 u8 ofdm_basic_rates;
713 u8 cck_basic_rates;
714 __le16 assoc_id;
715 __le32 flags;
716 __le32 filter_flags;
717 __le16 channel;
718 u8 ofdm_ht_single_stream_basic_rates;
719 u8 ofdm_ht_dual_stream_basic_rates;
720 u8 reserved4;
721 u8 reserved5;
722} __packed;
723
724
725/*
726 * REPLY_RXON_ASSOC = 0x11 (command, has simple generic response)
727 */
728struct iwl3945_rxon_assoc_cmd {
729 __le32 flags;
730 __le32 filter_flags;
731 u8 ofdm_basic_rates;
732 u8 cck_basic_rates;
733 __le16 reserved;
734} __packed;
735
736struct iwl4965_rxon_assoc_cmd {
737 __le32 flags;
738 __le32 filter_flags;
739 u8 ofdm_basic_rates;
740 u8 cck_basic_rates;
741 u8 ofdm_ht_single_stream_basic_rates;
742 u8 ofdm_ht_dual_stream_basic_rates;
743 __le16 rx_chain_select_flags;
744 __le16 reserved;
745} __packed;
746
747#define IWL_CONN_MAX_LISTEN_INTERVAL 10
748#define IWL_MAX_UCODE_BEACON_INTERVAL 4 /* 4096 */
749#define IWL39_MAX_UCODE_BEACON_INTERVAL 1 /* 1024 */
750
751/*
752 * REPLY_RXON_TIMING = 0x14 (command, has simple generic response)
753 */
754struct iwl_rxon_time_cmd {
755 __le64 timestamp;
756 __le16 beacon_interval;
757 __le16 atim_window;
758 __le32 beacon_init_val;
759 __le16 listen_interval;
760 u8 dtim_period;
761 u8 delta_cp_bss_tbtts;
762} __packed;
763
764/*
765 * REPLY_CHANNEL_SWITCH = 0x72 (command, has simple generic response)
766 */
767struct iwl3945_channel_switch_cmd {
768 u8 band;
769 u8 expect_beacon;
770 __le16 channel;
771 __le32 rxon_flags;
772 __le32 rxon_filter_flags;
773 __le32 switch_time;
774 struct iwl3945_power_per_rate power[IWL_MAX_RATES];
775} __packed;
776
777struct iwl4965_channel_switch_cmd {
778 u8 band;
779 u8 expect_beacon;
780 __le16 channel;
781 __le32 rxon_flags;
782 __le32 rxon_filter_flags;
783 __le32 switch_time;
784 struct iwl4965_tx_power_db tx_power;
785} __packed;
786
787/*
788 * CHANNEL_SWITCH_NOTIFICATION = 0x73 (notification only, not a command)
789 */
790struct iwl_csa_notification {
791 __le16 band;
792 __le16 channel;
793 __le32 status; /* 0 - OK, 1 - fail */
794} __packed;
795
796/******************************************************************************
797 * (2)
798 * Quality-of-Service (QOS) Commands & Responses:
799 *
800 *****************************************************************************/
801
802/**
803 * struct iwl_ac_qos -- QOS timing params for REPLY_QOS_PARAM
804 * One for each of 4 EDCA access categories in struct iwl_qosparam_cmd
805 *
806 * @cw_min: Contention window, start value in numbers of slots.
807 * Should be a power-of-2, minus 1. Device's default is 0x0f.
808 * @cw_max: Contention window, max value in numbers of slots.
809 * Should be a power-of-2, minus 1. Device's default is 0x3f.
810 * @aifsn: Number of slots in Arbitration Interframe Space (before
811 * performing random backoff timing prior to Tx). Device default 1.
812 * @edca_txop: Length of Tx opportunity, in uSecs. Device default is 0.
813 *
814 * Device will automatically increase contention window by (2*CW) + 1 for each
815 * transmission retry. Device uses cw_max as a bit mask, ANDed with new CW
816 * value, to cap the CW value.
817 */
818struct iwl_ac_qos {
819 __le16 cw_min;
820 __le16 cw_max;
821 u8 aifsn;
822 u8 reserved1;
823 __le16 edca_txop;
824} __packed;
825
826/* QoS flags defines */
827#define QOS_PARAM_FLG_UPDATE_EDCA_MSK cpu_to_le32(0x01)
828#define QOS_PARAM_FLG_TGN_MSK cpu_to_le32(0x02)
829#define QOS_PARAM_FLG_TXOP_TYPE_MSK cpu_to_le32(0x10)
830
831/* Number of Access Categories (AC) (EDCA), queues 0..3 */
832#define AC_NUM 4
833
834/*
835 * REPLY_QOS_PARAM = 0x13 (command, has simple generic response)
836 *
837 * This command sets up timings for each of the 4 prioritized EDCA Tx FIFOs
838 * 0: Background, 1: Best Effort, 2: Video, 3: Voice.
839 */
840struct iwl_qosparam_cmd {
841 __le32 qos_flags;
842 struct iwl_ac_qos ac[AC_NUM];
843} __packed;
844
845/******************************************************************************
846 * (3)
847 * Add/Modify Stations Commands & Responses:
848 *
849 *****************************************************************************/
850/*
851 * Multi station support
852 */
853
854/* Special, dedicated locations within device's station table */
855#define IWL_AP_ID 0
856#define IWL_STA_ID 2
857#define IWL3945_BROADCAST_ID 24
858#define IWL3945_STATION_COUNT 25
859#define IWL4965_BROADCAST_ID 31
860#define IWL4965_STATION_COUNT 32
861
862#define IWL_STATION_COUNT 32 /* MAX(3945,4965)*/
863#define IWL_INVALID_STATION 255
864
865#define STA_FLG_TX_RATE_MSK cpu_to_le32(1 << 2)
866#define STA_FLG_PWR_SAVE_MSK cpu_to_le32(1 << 8)
867#define STA_FLG_RTS_MIMO_PROT_MSK cpu_to_le32(1 << 17)
868#define STA_FLG_AGG_MPDU_8US_MSK cpu_to_le32(1 << 18)
869#define STA_FLG_MAX_AGG_SIZE_POS (19)
870#define STA_FLG_MAX_AGG_SIZE_MSK cpu_to_le32(3 << 19)
871#define STA_FLG_HT40_EN_MSK cpu_to_le32(1 << 21)
872#define STA_FLG_MIMO_DIS_MSK cpu_to_le32(1 << 22)
873#define STA_FLG_AGG_MPDU_DENSITY_POS (23)
874#define STA_FLG_AGG_MPDU_DENSITY_MSK cpu_to_le32(7 << 23)
875
876/* Use in mode field. 1: modify existing entry, 0: add new station entry */
877#define STA_CONTROL_MODIFY_MSK 0x01
878
879/* key flags __le16*/
880#define STA_KEY_FLG_ENCRYPT_MSK cpu_to_le16(0x0007)
881#define STA_KEY_FLG_NO_ENC cpu_to_le16(0x0000)
882#define STA_KEY_FLG_WEP cpu_to_le16(0x0001)
883#define STA_KEY_FLG_CCMP cpu_to_le16(0x0002)
884#define STA_KEY_FLG_TKIP cpu_to_le16(0x0003)
885
886#define STA_KEY_FLG_KEYID_POS 8
887#define STA_KEY_FLG_INVALID cpu_to_le16(0x0800)
888/* wep key is either from global key (0) or from station info array (1) */
889#define STA_KEY_FLG_MAP_KEY_MSK cpu_to_le16(0x0008)
890
891/* wep key in STA: 5-bytes (0) or 13-bytes (1) */
892#define STA_KEY_FLG_KEY_SIZE_MSK cpu_to_le16(0x1000)
893#define STA_KEY_MULTICAST_MSK cpu_to_le16(0x4000)
894#define STA_KEY_MAX_NUM 8
895
896/* Flags indicate whether to modify vs. don't change various station params */
897#define STA_MODIFY_KEY_MASK 0x01
898#define STA_MODIFY_TID_DISABLE_TX 0x02
899#define STA_MODIFY_TX_RATE_MSK 0x04
900#define STA_MODIFY_ADDBA_TID_MSK 0x08
901#define STA_MODIFY_DELBA_TID_MSK 0x10
902#define STA_MODIFY_SLEEP_TX_COUNT_MSK 0x20
903
904/* Receiver address (actually, Rx station's index into station table),
905 * combined with Traffic ID (QOS priority), in format used by Tx Scheduler */
906#define BUILD_RAxTID(sta_id, tid) (((sta_id) << 4) + (tid))
907
908struct iwl4965_keyinfo {
909 __le16 key_flags;
910 u8 tkip_rx_tsc_byte2; /* TSC[2] for key mix ph1 detection */
911 u8 reserved1;
912 __le16 tkip_rx_ttak[5]; /* 10-byte unicast TKIP TTAK */
913 u8 key_offset;
914 u8 reserved2;
915 u8 key[16]; /* 16-byte unicast decryption key */
916} __packed;
917
918/**
919 * struct sta_id_modify
920 * @addr[ETH_ALEN]: station's MAC address
921 * @sta_id: index of station in uCode's station table
922 * @modify_mask: STA_MODIFY_*, 1: modify, 0: don't change
923 *
924 * Driver selects unused table index when adding new station,
925 * or the index to a pre-existing station entry when modifying that station.
926 * Some indexes have special purposes (IWL_AP_ID, index 0, is for AP).
927 *
928 * modify_mask flags select which parameters to modify vs. leave alone.
929 */
930struct sta_id_modify {
931 u8 addr[ETH_ALEN];
932 __le16 reserved1;
933 u8 sta_id;
934 u8 modify_mask;
935 __le16 reserved2;
936} __packed;
937
938/*
939 * REPLY_ADD_STA = 0x18 (command)
940 *
941 * The device contains an internal table of per-station information,
942 * with info on security keys, aggregation parameters, and Tx rates for
943 * initial Tx attempt and any retries (4965 devices uses
944 * REPLY_TX_LINK_QUALITY_CMD,
945 * 3945 uses REPLY_RATE_SCALE to set up rate tables).
946 *
947 * REPLY_ADD_STA sets up the table entry for one station, either creating
948 * a new entry, or modifying a pre-existing one.
949 *
950 * NOTE: RXON command (without "associated" bit set) wipes the station table
951 * clean. Moving into RF_KILL state does this also. Driver must set up
952 * new station table before transmitting anything on the RXON channel
953 * (except active scans or active measurements; those commands carry
954 * their own txpower/rate setup data).
955 *
956 * When getting started on a new channel, driver must set up the
957 * IWL_BROADCAST_ID entry (last entry in the table). For a client
958 * station in a BSS, once an AP is selected, driver sets up the AP STA
959 * in the IWL_AP_ID entry (1st entry in the table). BROADCAST and AP
960 * are all that are needed for a BSS client station. If the device is
961 * used as AP, or in an IBSS network, driver must set up station table
962 * entries for all STAs in network, starting with index IWL_STA_ID.
963 */
964
965struct iwl3945_addsta_cmd {
966 u8 mode; /* 1: modify existing, 0: add new station */
967 u8 reserved[3];
968 struct sta_id_modify sta;
969 struct iwl4965_keyinfo key;
970 __le32 station_flags; /* STA_FLG_* */
971 __le32 station_flags_msk; /* STA_FLG_* */
972
973 /* bit field to disable (1) or enable (0) Tx for Traffic ID (TID)
974 * corresponding to bit (e.g. bit 5 controls TID 5).
975 * Set modify_mask bit STA_MODIFY_TID_DISABLE_TX to use this field. */
976 __le16 tid_disable_tx;
977
978 __le16 rate_n_flags;
979
980 /* TID for which to add block-ack support.
981 * Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
982 u8 add_immediate_ba_tid;
983
984 /* TID for which to remove block-ack support.
985 * Set modify_mask bit STA_MODIFY_DELBA_TID_MSK to use this field. */
986 u8 remove_immediate_ba_tid;
987
988 /* Starting Sequence Number for added block-ack support.
989 * Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
990 __le16 add_immediate_ba_ssn;
991} __packed;
992
993struct iwl4965_addsta_cmd {
994 u8 mode; /* 1: modify existing, 0: add new station */
995 u8 reserved[3];
996 struct sta_id_modify sta;
997 struct iwl4965_keyinfo key;
998 __le32 station_flags; /* STA_FLG_* */
999 __le32 station_flags_msk; /* STA_FLG_* */
1000
1001 /* bit field to disable (1) or enable (0) Tx for Traffic ID (TID)
1002 * corresponding to bit (e.g. bit 5 controls TID 5).
1003 * Set modify_mask bit STA_MODIFY_TID_DISABLE_TX to use this field. */
1004 __le16 tid_disable_tx;
1005
1006 __le16 reserved1;
1007
1008 /* TID for which to add block-ack support.
1009 * Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
1010 u8 add_immediate_ba_tid;
1011
1012 /* TID for which to remove block-ack support.
1013 * Set modify_mask bit STA_MODIFY_DELBA_TID_MSK to use this field. */
1014 u8 remove_immediate_ba_tid;
1015
1016 /* Starting Sequence Number for added block-ack support.
1017 * Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
1018 __le16 add_immediate_ba_ssn;
1019
1020 /*
1021 * Number of packets OK to transmit to station even though
1022 * it is asleep -- used to synchronise PS-poll and u-APSD
1023 * responses while ucode keeps track of STA sleep state.
1024 */
1025 __le16 sleep_tx_count;
1026
1027 __le16 reserved2;
1028} __packed;
1029
1030/* Wrapper struct for 3945 and 4965 addsta_cmd structures */
1031struct iwl_legacy_addsta_cmd {
1032 u8 mode; /* 1: modify existing, 0: add new station */
1033 u8 reserved[3];
1034 struct sta_id_modify sta;
1035 struct iwl4965_keyinfo key;
1036 __le32 station_flags; /* STA_FLG_* */
1037 __le32 station_flags_msk; /* STA_FLG_* */
1038
1039 /* bit field to disable (1) or enable (0) Tx for Traffic ID (TID)
1040 * corresponding to bit (e.g. bit 5 controls TID 5).
1041 * Set modify_mask bit STA_MODIFY_TID_DISABLE_TX to use this field. */
1042 __le16 tid_disable_tx;
1043
1044 __le16 rate_n_flags; /* 3945 only */
1045
1046 /* TID for which to add block-ack support.
1047 * Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
1048 u8 add_immediate_ba_tid;
1049
1050 /* TID for which to remove block-ack support.
1051 * Set modify_mask bit STA_MODIFY_DELBA_TID_MSK to use this field. */
1052 u8 remove_immediate_ba_tid;
1053
1054 /* Starting Sequence Number for added block-ack support.
1055 * Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
1056 __le16 add_immediate_ba_ssn;
1057
1058 /*
1059 * Number of packets OK to transmit to station even though
1060 * it is asleep -- used to synchronise PS-poll and u-APSD
1061 * responses while ucode keeps track of STA sleep state.
1062 */
1063 __le16 sleep_tx_count;
1064
1065 __le16 reserved2;
1066} __packed;
1067
1068
1069#define ADD_STA_SUCCESS_MSK 0x1
1070#define ADD_STA_NO_ROOM_IN_TABLE 0x2
1071#define ADD_STA_NO_BLOCK_ACK_RESOURCE 0x4
1072#define ADD_STA_MODIFY_NON_EXIST_STA 0x8
1073/*
1074 * REPLY_ADD_STA = 0x18 (response)
1075 */
1076struct iwl_add_sta_resp {
1077 u8 status; /* ADD_STA_* */
1078} __packed;
1079
1080#define REM_STA_SUCCESS_MSK 0x1
1081/*
1082 * REPLY_REM_STA = 0x19 (response)
1083 */
1084struct iwl_rem_sta_resp {
1085 u8 status;
1086} __packed;
1087
1088/*
1089 * REPLY_REM_STA = 0x19 (command)
1090 */
1091struct iwl_rem_sta_cmd {
1092 u8 num_sta; /* number of removed stations */
1093 u8 reserved[3];
1094 u8 addr[ETH_ALEN]; /* MAC addr of the first station */
1095 u8 reserved2[2];
1096} __packed;
1097
1098#define IWL_TX_FIFO_BK_MSK cpu_to_le32(BIT(0))
1099#define IWL_TX_FIFO_BE_MSK cpu_to_le32(BIT(1))
1100#define IWL_TX_FIFO_VI_MSK cpu_to_le32(BIT(2))
1101#define IWL_TX_FIFO_VO_MSK cpu_to_le32(BIT(3))
1102#define IWL_AGG_TX_QUEUE_MSK cpu_to_le32(0xffc00)
1103
1104#define IWL_DROP_SINGLE 0
1105#define IWL_DROP_SELECTED 1
1106#define IWL_DROP_ALL 2
1107
1108/*
1109 * REPLY_WEP_KEY = 0x20
1110 */
1111struct iwl_wep_key {
1112 u8 key_index;
1113 u8 key_offset;
1114 u8 reserved1[2];
1115 u8 key_size;
1116 u8 reserved2[3];
1117 u8 key[16];
1118} __packed;
1119
1120struct iwl_wep_cmd {
1121 u8 num_keys;
1122 u8 global_key_type;
1123 u8 flags;
1124 u8 reserved;
1125 struct iwl_wep_key key[0];
1126} __packed;
1127
1128#define WEP_KEY_WEP_TYPE 1
1129#define WEP_KEYS_MAX 4
1130#define WEP_INVALID_OFFSET 0xff
1131#define WEP_KEY_LEN_64 5
1132#define WEP_KEY_LEN_128 13
1133
1134/******************************************************************************
1135 * (4)
1136 * Rx Responses:
1137 *
1138 *****************************************************************************/
1139
1140#define RX_RES_STATUS_NO_CRC32_ERROR cpu_to_le32(1 << 0)
1141#define RX_RES_STATUS_NO_RXE_OVERFLOW cpu_to_le32(1 << 1)
1142
1143#define RX_RES_PHY_FLAGS_BAND_24_MSK cpu_to_le16(1 << 0)
1144#define RX_RES_PHY_FLAGS_MOD_CCK_MSK cpu_to_le16(1 << 1)
1145#define RX_RES_PHY_FLAGS_SHORT_PREAMBLE_MSK cpu_to_le16(1 << 2)
1146#define RX_RES_PHY_FLAGS_NARROW_BAND_MSK cpu_to_le16(1 << 3)
1147#define RX_RES_PHY_FLAGS_ANTENNA_MSK 0xf0
1148#define RX_RES_PHY_FLAGS_ANTENNA_POS 4
1149
1150#define RX_RES_STATUS_SEC_TYPE_MSK (0x7 << 8)
1151#define RX_RES_STATUS_SEC_TYPE_NONE (0x0 << 8)
1152#define RX_RES_STATUS_SEC_TYPE_WEP (0x1 << 8)
1153#define RX_RES_STATUS_SEC_TYPE_CCMP (0x2 << 8)
1154#define RX_RES_STATUS_SEC_TYPE_TKIP (0x3 << 8)
1155#define RX_RES_STATUS_SEC_TYPE_ERR (0x7 << 8)
1156
1157#define RX_RES_STATUS_STATION_FOUND (1<<6)
1158#define RX_RES_STATUS_NO_STATION_INFO_MISMATCH (1<<7)
1159
1160#define RX_RES_STATUS_DECRYPT_TYPE_MSK (0x3 << 11)
1161#define RX_RES_STATUS_NOT_DECRYPT (0x0 << 11)
1162#define RX_RES_STATUS_DECRYPT_OK (0x3 << 11)
1163#define RX_RES_STATUS_BAD_ICV_MIC (0x1 << 11)
1164#define RX_RES_STATUS_BAD_KEY_TTAK (0x2 << 11)
1165
1166#define RX_MPDU_RES_STATUS_ICV_OK (0x20)
1167#define RX_MPDU_RES_STATUS_MIC_OK (0x40)
1168#define RX_MPDU_RES_STATUS_TTAK_OK (1 << 7)
1169#define RX_MPDU_RES_STATUS_DEC_DONE_MSK (0x800)
1170
1171
1172struct iwl3945_rx_frame_stats {
1173 u8 phy_count;
1174 u8 id;
1175 u8 rssi;
1176 u8 agc;
1177 __le16 sig_avg;
1178 __le16 noise_diff;
1179 u8 payload[0];
1180} __packed;
1181
1182struct iwl3945_rx_frame_hdr {
1183 __le16 channel;
1184 __le16 phy_flags;
1185 u8 reserved1;
1186 u8 rate;
1187 __le16 len;
1188 u8 payload[0];
1189} __packed;
1190
1191struct iwl3945_rx_frame_end {
1192 __le32 status;
1193 __le64 timestamp;
1194 __le32 beacon_timestamp;
1195} __packed;
1196
1197/*
1198 * REPLY_3945_RX = 0x1b (response only, not a command)
1199 *
1200 * NOTE: DO NOT dereference from casts to this structure
1201 * It is provided only for calculating minimum data set size.
1202 * The actual offsets of the hdr and end are dynamic based on
1203 * stats.phy_count
1204 */
1205struct iwl3945_rx_frame {
1206 struct iwl3945_rx_frame_stats stats;
1207 struct iwl3945_rx_frame_hdr hdr;
1208 struct iwl3945_rx_frame_end end;
1209} __packed;
1210
1211#define IWL39_RX_FRAME_SIZE (4 + sizeof(struct iwl3945_rx_frame))
1212
1213/* Fixed (non-configurable) rx data from phy */
1214
1215#define IWL49_RX_RES_PHY_CNT 14
1216#define IWL49_RX_PHY_FLAGS_ANTENNAE_OFFSET (4)
1217#define IWL49_RX_PHY_FLAGS_ANTENNAE_MASK (0x70)
1218#define IWL49_AGC_DB_MASK (0x3f80) /* MASK(7,13) */
1219#define IWL49_AGC_DB_POS (7)
1220struct iwl4965_rx_non_cfg_phy {
1221 __le16 ant_selection; /* ant A bit 4, ant B bit 5, ant C bit 6 */
1222 __le16 agc_info; /* agc code 0:6, agc dB 7:13, reserved 14:15 */
1223 u8 rssi_info[6]; /* we use even entries, 0/2/4 for A/B/C rssi */
1224 u8 pad[0];
1225} __packed;
1226
1227
1228/*
1229 * REPLY_RX = 0xc3 (response only, not a command)
1230 * Used only for legacy (non 11n) frames.
1231 */
1232struct iwl_rx_phy_res {
1233 u8 non_cfg_phy_cnt; /* non configurable DSP phy data byte count */
1234 u8 cfg_phy_cnt; /* configurable DSP phy data byte count */
1235 u8 stat_id; /* configurable DSP phy data set ID */
1236 u8 reserved1;
1237 __le64 timestamp; /* TSF at on air rise */
1238 __le32 beacon_time_stamp; /* beacon at on-air rise */
1239 __le16 phy_flags; /* general phy flags: band, modulation, ... */
1240 __le16 channel; /* channel number */
1241 u8 non_cfg_phy_buf[32]; /* for various implementations of non_cfg_phy */
1242 __le32 rate_n_flags; /* RATE_MCS_* */
1243 __le16 byte_count; /* frame's byte-count */
1244 __le16 frame_time; /* frame's time on the air */
1245} __packed;
1246
1247struct iwl_rx_mpdu_res_start {
1248 __le16 byte_count;
1249 __le16 reserved;
1250} __packed;
1251
1252
1253/******************************************************************************
1254 * (5)
1255 * Tx Commands & Responses:
1256 *
1257 * Driver must place each REPLY_TX command into one of the prioritized Tx
1258 * queues in host DRAM, shared between driver and device (see comments for
1259 * SCD registers and Tx/Rx Queues). When the device's Tx scheduler and uCode
1260 * are preparing to transmit, the device pulls the Tx command over the PCI
1261 * bus via one of the device's Tx DMA channels, to fill an internal FIFO
1262 * from which data will be transmitted.
1263 *
1264 * uCode handles all timing and protocol related to control frames
1265 * (RTS/CTS/ACK), based on flags in the Tx command. uCode and Tx scheduler
1266 * handle reception of block-acks; uCode updates the host driver via
1267 * REPLY_COMPRESSED_BA.
1268 *
1269 * uCode handles retrying Tx when an ACK is expected but not received.
1270 * This includes trying lower data rates than the one requested in the Tx
1271 * command, as set up by the REPLY_RATE_SCALE (for 3945) or
1272 * REPLY_TX_LINK_QUALITY_CMD (4965).
1273 *
1274 * Driver sets up transmit power for various rates via REPLY_TX_PWR_TABLE_CMD.
1275 * This command must be executed after every RXON command, before Tx can occur.
1276 *****************************************************************************/
1277
1278/* REPLY_TX Tx flags field */
1279
1280/*
1281 * 1: Use Request-To-Send protocol before this frame.
1282 * Mutually exclusive vs. TX_CMD_FLG_CTS_MSK.
1283 */
1284#define TX_CMD_FLG_RTS_MSK cpu_to_le32(1 << 1)
1285
1286/*
1287 * 1: Transmit Clear-To-Send to self before this frame.
1288 * Driver should set this for AUTH/DEAUTH/ASSOC-REQ/REASSOC mgmnt frames.
1289 * Mutually exclusive vs. TX_CMD_FLG_RTS_MSK.
1290 */
1291#define TX_CMD_FLG_CTS_MSK cpu_to_le32(1 << 2)
1292
1293/* 1: Expect ACK from receiving station
1294 * 0: Don't expect ACK (MAC header's duration field s/b 0)
1295 * Set this for unicast frames, but not broadcast/multicast. */
1296#define TX_CMD_FLG_ACK_MSK cpu_to_le32(1 << 3)
1297
1298/* For 4965 devices:
1299 * 1: Use rate scale table (see REPLY_TX_LINK_QUALITY_CMD).
1300 * Tx command's initial_rate_index indicates first rate to try;
1301 * uCode walks through table for additional Tx attempts.
1302 * 0: Use Tx rate/MCS from Tx command's rate_n_flags field.
1303 * This rate will be used for all Tx attempts; it will not be scaled. */
1304#define TX_CMD_FLG_STA_RATE_MSK cpu_to_le32(1 << 4)
1305
1306/* 1: Expect immediate block-ack.
1307 * Set when Txing a block-ack request frame. Also set TX_CMD_FLG_ACK_MSK. */
1308#define TX_CMD_FLG_IMM_BA_RSP_MASK cpu_to_le32(1 << 6)
1309
1310/*
1311 * 1: Frame requires full Tx-Op protection.
1312 * Set this if either RTS or CTS Tx Flag gets set.
1313 */
1314#define TX_CMD_FLG_FULL_TXOP_PROT_MSK cpu_to_le32(1 << 7)
1315
1316/* Tx antenna selection field; used only for 3945, reserved (0) for 4965 devices.
1317 * Set field to "0" to allow 3945 uCode to select antenna (normal usage). */
1318#define TX_CMD_FLG_ANT_SEL_MSK cpu_to_le32(0xf00)
1319#define TX_CMD_FLG_ANT_A_MSK cpu_to_le32(1 << 8)
1320#define TX_CMD_FLG_ANT_B_MSK cpu_to_le32(1 << 9)
1321
1322/* 1: uCode overrides sequence control field in MAC header.
1323 * 0: Driver provides sequence control field in MAC header.
1324 * Set this for management frames, non-QOS data frames, non-unicast frames,
1325 * and also in Tx command embedded in REPLY_SCAN_CMD for active scans. */
1326#define TX_CMD_FLG_SEQ_CTL_MSK cpu_to_le32(1 << 13)
1327
1328/* 1: This frame is non-last MPDU; more fragments are coming.
1329 * 0: Last fragment, or not using fragmentation. */
1330#define TX_CMD_FLG_MORE_FRAG_MSK cpu_to_le32(1 << 14)
1331
1332/* 1: uCode calculates and inserts Timestamp Function (TSF) in outgoing frame.
1333 * 0: No TSF required in outgoing frame.
1334 * Set this for transmitting beacons and probe responses. */
1335#define TX_CMD_FLG_TSF_MSK cpu_to_le32(1 << 16)
1336
1337/* 1: Driver inserted 2 bytes pad after the MAC header, for (required) dword
1338 * alignment of frame's payload data field.
1339 * 0: No pad
1340 * Set this for MAC headers with 26 or 30 bytes, i.e. those with QOS or ADDR4
1341 * field (but not both). Driver must align frame data (i.e. data following
1342 * MAC header) to DWORD boundary. */
1343#define TX_CMD_FLG_MH_PAD_MSK cpu_to_le32(1 << 20)
1344
1345/* accelerate aggregation support
1346 * 0 - no CCMP encryption; 1 - CCMP encryption */
1347#define TX_CMD_FLG_AGG_CCMP_MSK cpu_to_le32(1 << 22)
1348
1349/* HCCA-AP - disable duration overwriting. */
1350#define TX_CMD_FLG_DUR_MSK cpu_to_le32(1 << 25)
1351
1352
1353/*
1354 * TX command security control
1355 */
1356#define TX_CMD_SEC_WEP 0x01
1357#define TX_CMD_SEC_CCM 0x02
1358#define TX_CMD_SEC_TKIP 0x03
1359#define TX_CMD_SEC_MSK 0x03
1360#define TX_CMD_SEC_SHIFT 6
1361#define TX_CMD_SEC_KEY128 0x08
1362
1363/*
1364 * security overhead sizes
1365 */
1366#define WEP_IV_LEN 4
1367#define WEP_ICV_LEN 4
1368#define CCMP_MIC_LEN 8
1369#define TKIP_ICV_LEN 4
1370
1371/*
1372 * REPLY_TX = 0x1c (command)
1373 */
1374
1375struct iwl3945_tx_cmd {
1376 /*
1377 * MPDU byte count:
1378 * MAC header (24/26/30/32 bytes) + 2 bytes pad if 26/30 header size,
1379 * + 8 byte IV for CCM or TKIP (not used for WEP)
1380 * + Data payload
1381 * + 8-byte MIC (not used for CCM/WEP)
1382 * NOTE: Does not include Tx command bytes, post-MAC pad bytes,
1383 * MIC (CCM) 8 bytes, ICV (WEP/TKIP/CKIP) 4 bytes, CRC 4 bytes.i
1384 * Range: 14-2342 bytes.
1385 */
1386 __le16 len;
1387
1388 /*
1389 * MPDU or MSDU byte count for next frame.
1390 * Used for fragmentation and bursting, but not 11n aggregation.
1391 * Same as "len", but for next frame. Set to 0 if not applicable.
1392 */
1393 __le16 next_frame_len;
1394
1395 __le32 tx_flags; /* TX_CMD_FLG_* */
1396
1397 u8 rate;
1398
1399 /* Index of recipient station in uCode's station table */
1400 u8 sta_id;
1401 u8 tid_tspec;
1402 u8 sec_ctl;
1403 u8 key[16];
1404 union {
1405 u8 byte[8];
1406 __le16 word[4];
1407 __le32 dw[2];
1408 } tkip_mic;
1409 __le32 next_frame_info;
1410 union {
1411 __le32 life_time;
1412 __le32 attempt;
1413 } stop_time;
1414 u8 supp_rates[2];
1415 u8 rts_retry_limit; /*byte 50 */
1416 u8 data_retry_limit; /*byte 51 */
1417 union {
1418 __le16 pm_frame_timeout;
1419 __le16 attempt_duration;
1420 } timeout;
1421
1422 /*
1423 * Duration of EDCA burst Tx Opportunity, in 32-usec units.
1424 * Set this if txop time is not specified by HCCA protocol (e.g. by AP).
1425 */
1426 __le16 driver_txop;
1427
1428 /*
1429 * MAC header goes here, followed by 2 bytes padding if MAC header
1430 * length is 26 or 30 bytes, followed by payload data
1431 */
1432 u8 payload[0];
1433 struct ieee80211_hdr hdr[0];
1434} __packed;
1435
1436/*
1437 * REPLY_TX = 0x1c (response)
1438 */
1439struct iwl3945_tx_resp {
1440 u8 failure_rts;
1441 u8 failure_frame;
1442 u8 bt_kill_count;
1443 u8 rate;
1444 __le32 wireless_media_time;
1445 __le32 status; /* TX status */
1446} __packed;
1447
1448
1449/*
1450 * 4965 uCode updates these Tx attempt count values in host DRAM.
1451 * Used for managing Tx retries when expecting block-acks.
1452 * Driver should set these fields to 0.
1453 */
1454struct iwl_dram_scratch {
1455 u8 try_cnt; /* Tx attempts */
1456 u8 bt_kill_cnt; /* Tx attempts blocked by Bluetooth device */
1457 __le16 reserved;
1458} __packed;
1459
1460struct iwl_tx_cmd {
1461 /*
1462 * MPDU byte count:
1463 * MAC header (24/26/30/32 bytes) + 2 bytes pad if 26/30 header size,
1464 * + 8 byte IV for CCM or TKIP (not used for WEP)
1465 * + Data payload
1466 * + 8-byte MIC (not used for CCM/WEP)
1467 * NOTE: Does not include Tx command bytes, post-MAC pad bytes,
1468 * MIC (CCM) 8 bytes, ICV (WEP/TKIP/CKIP) 4 bytes, CRC 4 bytes.i
1469 * Range: 14-2342 bytes.
1470 */
1471 __le16 len;
1472
1473 /*
1474 * MPDU or MSDU byte count for next frame.
1475 * Used for fragmentation and bursting, but not 11n aggregation.
1476 * Same as "len", but for next frame. Set to 0 if not applicable.
1477 */
1478 __le16 next_frame_len;
1479
1480 __le32 tx_flags; /* TX_CMD_FLG_* */
1481
1482 /* uCode may modify this field of the Tx command (in host DRAM!).
1483 * Driver must also set dram_lsb_ptr and dram_msb_ptr in this cmd. */
1484 struct iwl_dram_scratch scratch;
1485
1486 /* Rate for *all* Tx attempts, if TX_CMD_FLG_STA_RATE_MSK is cleared. */
1487 __le32 rate_n_flags; /* RATE_MCS_* */
1488
1489 /* Index of destination station in uCode's station table */
1490 u8 sta_id;
1491
1492 /* Type of security encryption: CCM or TKIP */
1493 u8 sec_ctl; /* TX_CMD_SEC_* */
1494
1495 /*
1496 * Index into rate table (see REPLY_TX_LINK_QUALITY_CMD) for initial
1497 * Tx attempt, if TX_CMD_FLG_STA_RATE_MSK is set. Normally "0" for
1498 * data frames, this field may be used to selectively reduce initial
1499 * rate (via non-0 value) for special frames (e.g. management), while
1500 * still supporting rate scaling for all frames.
1501 */
1502 u8 initial_rate_index;
1503 u8 reserved;
1504 u8 key[16];
1505 __le16 next_frame_flags;
1506 __le16 reserved2;
1507 union {
1508 __le32 life_time;
1509 __le32 attempt;
1510 } stop_time;
1511
1512 /* Host DRAM physical address pointer to "scratch" in this command.
1513 * Must be dword aligned. "0" in dram_lsb_ptr disables usage. */
1514 __le32 dram_lsb_ptr;
1515 u8 dram_msb_ptr;
1516
1517 u8 rts_retry_limit; /*byte 50 */
1518 u8 data_retry_limit; /*byte 51 */
1519 u8 tid_tspec;
1520 union {
1521 __le16 pm_frame_timeout;
1522 __le16 attempt_duration;
1523 } timeout;
1524
1525 /*
1526 * Duration of EDCA burst Tx Opportunity, in 32-usec units.
1527 * Set this if txop time is not specified by HCCA protocol (e.g. by AP).
1528 */
1529 __le16 driver_txop;
1530
1531 /*
1532 * MAC header goes here, followed by 2 bytes padding if MAC header
1533 * length is 26 or 30 bytes, followed by payload data
1534 */
1535 u8 payload[0];
1536 struct ieee80211_hdr hdr[0];
1537} __packed;
1538
1539/* TX command response is sent after *3945* transmission attempts.
1540 *
1541 * NOTES:
1542 *
1543 * TX_STATUS_FAIL_NEXT_FRAG
1544 *
1545 * If the fragment flag in the MAC header for the frame being transmitted
1546 * is set and there is insufficient time to transmit the next frame, the
1547 * TX status will be returned with 'TX_STATUS_FAIL_NEXT_FRAG'.
1548 *
1549 * TX_STATUS_FIFO_UNDERRUN
1550 *
1551 * Indicates the host did not provide bytes to the FIFO fast enough while
1552 * a TX was in progress.
1553 *
1554 * TX_STATUS_FAIL_MGMNT_ABORT
1555 *
1556 * This status is only possible if the ABORT ON MGMT RX parameter was
1557 * set to true with the TX command.
1558 *
1559 * If the MSB of the status parameter is set then an abort sequence is
1560 * required. This sequence consists of the host activating the TX Abort
1561 * control line, and then waiting for the TX Abort command response. This
1562 * indicates that a the device is no longer in a transmit state, and that the
1563 * command FIFO has been cleared. The host must then deactivate the TX Abort
1564 * control line. Receiving is still allowed in this case.
1565 */
1566enum {
1567 TX_3945_STATUS_SUCCESS = 0x01,
1568 TX_3945_STATUS_DIRECT_DONE = 0x02,
1569 TX_3945_STATUS_FAIL_SHORT_LIMIT = 0x82,
1570 TX_3945_STATUS_FAIL_LONG_LIMIT = 0x83,
1571 TX_3945_STATUS_FAIL_FIFO_UNDERRUN = 0x84,
1572 TX_3945_STATUS_FAIL_MGMNT_ABORT = 0x85,
1573 TX_3945_STATUS_FAIL_NEXT_FRAG = 0x86,
1574 TX_3945_STATUS_FAIL_LIFE_EXPIRE = 0x87,
1575 TX_3945_STATUS_FAIL_DEST_PS = 0x88,
1576 TX_3945_STATUS_FAIL_ABORTED = 0x89,
1577 TX_3945_STATUS_FAIL_BT_RETRY = 0x8a,
1578 TX_3945_STATUS_FAIL_STA_INVALID = 0x8b,
1579 TX_3945_STATUS_FAIL_FRAG_DROPPED = 0x8c,
1580 TX_3945_STATUS_FAIL_TID_DISABLE = 0x8d,
1581 TX_3945_STATUS_FAIL_FRAME_FLUSHED = 0x8e,
1582 TX_3945_STATUS_FAIL_INSUFFICIENT_CF_POLL = 0x8f,
1583 TX_3945_STATUS_FAIL_TX_LOCKED = 0x90,
1584 TX_3945_STATUS_FAIL_NO_BEACON_ON_RADAR = 0x91,
1585};
1586
1587/*
1588 * TX command response is sent after *4965* transmission attempts.
1589 *
1590 * both postpone and abort status are expected behavior from uCode. there is
1591 * no special operation required from driver; except for RFKILL_FLUSH,
1592 * which required tx flush host command to flush all the tx frames in queues
1593 */
1594enum {
1595 TX_STATUS_SUCCESS = 0x01,
1596 TX_STATUS_DIRECT_DONE = 0x02,
1597 /* postpone TX */
1598 TX_STATUS_POSTPONE_DELAY = 0x40,
1599 TX_STATUS_POSTPONE_FEW_BYTES = 0x41,
1600 TX_STATUS_POSTPONE_QUIET_PERIOD = 0x43,
1601 TX_STATUS_POSTPONE_CALC_TTAK = 0x44,
1602 /* abort TX */
1603 TX_STATUS_FAIL_INTERNAL_CROSSED_RETRY = 0x81,
1604 TX_STATUS_FAIL_SHORT_LIMIT = 0x82,
1605 TX_STATUS_FAIL_LONG_LIMIT = 0x83,
1606 TX_STATUS_FAIL_FIFO_UNDERRUN = 0x84,
1607 TX_STATUS_FAIL_DRAIN_FLOW = 0x85,
1608 TX_STATUS_FAIL_RFKILL_FLUSH = 0x86,
1609 TX_STATUS_FAIL_LIFE_EXPIRE = 0x87,
1610 TX_STATUS_FAIL_DEST_PS = 0x88,
1611 TX_STATUS_FAIL_HOST_ABORTED = 0x89,
1612 TX_STATUS_FAIL_BT_RETRY = 0x8a,
1613 TX_STATUS_FAIL_STA_INVALID = 0x8b,
1614 TX_STATUS_FAIL_FRAG_DROPPED = 0x8c,
1615 TX_STATUS_FAIL_TID_DISABLE = 0x8d,
1616 TX_STATUS_FAIL_FIFO_FLUSHED = 0x8e,
1617 TX_STATUS_FAIL_INSUFFICIENT_CF_POLL = 0x8f,
1618 TX_STATUS_FAIL_PASSIVE_NO_RX = 0x90,
1619 TX_STATUS_FAIL_NO_BEACON_ON_RADAR = 0x91,
1620};
1621
1622#define TX_PACKET_MODE_REGULAR 0x0000
1623#define TX_PACKET_MODE_BURST_SEQ 0x0100
1624#define TX_PACKET_MODE_BURST_FIRST 0x0200
1625
1626enum {
1627 TX_POWER_PA_NOT_ACTIVE = 0x0,
1628};
1629
1630enum {
1631 TX_STATUS_MSK = 0x000000ff, /* bits 0:7 */
1632 TX_STATUS_DELAY_MSK = 0x00000040,
1633 TX_STATUS_ABORT_MSK = 0x00000080,
1634 TX_PACKET_MODE_MSK = 0x0000ff00, /* bits 8:15 */
1635 TX_FIFO_NUMBER_MSK = 0x00070000, /* bits 16:18 */
1636 TX_RESERVED = 0x00780000, /* bits 19:22 */
1637 TX_POWER_PA_DETECT_MSK = 0x7f800000, /* bits 23:30 */
1638 TX_ABORT_REQUIRED_MSK = 0x80000000, /* bits 31:31 */
1639};
1640
1641/* *******************************
1642 * TX aggregation status
1643 ******************************* */
1644
1645enum {
1646 AGG_TX_STATE_TRANSMITTED = 0x00,
1647 AGG_TX_STATE_UNDERRUN_MSK = 0x01,
1648 AGG_TX_STATE_FEW_BYTES_MSK = 0x04,
1649 AGG_TX_STATE_ABORT_MSK = 0x08,
1650 AGG_TX_STATE_LAST_SENT_TTL_MSK = 0x10,
1651 AGG_TX_STATE_LAST_SENT_TRY_CNT_MSK = 0x20,
1652 AGG_TX_STATE_SCD_QUERY_MSK = 0x80,
1653 AGG_TX_STATE_TEST_BAD_CRC32_MSK = 0x100,
1654 AGG_TX_STATE_RESPONSE_MSK = 0x1ff,
1655 AGG_TX_STATE_DUMP_TX_MSK = 0x200,
1656 AGG_TX_STATE_DELAY_TX_MSK = 0x400
1657};
1658
1659#define AGG_TX_STATUS_MSK 0x00000fff /* bits 0:11 */
1660#define AGG_TX_TRY_MSK 0x0000f000 /* bits 12:15 */
1661
1662#define AGG_TX_STATE_LAST_SENT_MSK (AGG_TX_STATE_LAST_SENT_TTL_MSK | \
1663 AGG_TX_STATE_LAST_SENT_TRY_CNT_MSK)
1664
1665/* # tx attempts for first frame in aggregation */
1666#define AGG_TX_STATE_TRY_CNT_POS 12
1667#define AGG_TX_STATE_TRY_CNT_MSK 0xf000
1668
1669/* Command ID and sequence number of Tx command for this frame */
1670#define AGG_TX_STATE_SEQ_NUM_POS 16
1671#define AGG_TX_STATE_SEQ_NUM_MSK 0xffff0000
1672
1673/*
1674 * REPLY_TX = 0x1c (response)
1675 *
1676 * This response may be in one of two slightly different formats, indicated
1677 * by the frame_count field:
1678 *
1679 * 1) No aggregation (frame_count == 1). This reports Tx results for
1680 * a single frame. Multiple attempts, at various bit rates, may have
1681 * been made for this frame.
1682 *
1683 * 2) Aggregation (frame_count > 1). This reports Tx results for
1684 * 2 or more frames that used block-acknowledge. All frames were
1685 * transmitted at same rate. Rate scaling may have been used if first
1686 * frame in this new agg block failed in previous agg block(s).
1687 *
1688 * Note that, for aggregation, ACK (block-ack) status is not delivered here;
1689 * block-ack has not been received by the time the 4965 device records
1690 * this status.
1691 * This status relates to reasons the tx might have been blocked or aborted
1692 * within the sending station (this 4965 device), rather than whether it was
1693 * received successfully by the destination station.
1694 */
1695struct agg_tx_status {
1696 __le16 status;
1697 __le16 sequence;
1698} __packed;
1699
1700struct iwl4965_tx_resp {
1701 u8 frame_count; /* 1 no aggregation, >1 aggregation */
1702 u8 bt_kill_count; /* # blocked by bluetooth (unused for agg) */
1703 u8 failure_rts; /* # failures due to unsuccessful RTS */
1704 u8 failure_frame; /* # failures due to no ACK (unused for agg) */
1705
1706 /* For non-agg: Rate at which frame was successful.
1707 * For agg: Rate at which all frames were transmitted. */
1708 __le32 rate_n_flags; /* RATE_MCS_* */
1709
1710 /* For non-agg: RTS + CTS + frame tx attempts time + ACK.
1711 * For agg: RTS + CTS + aggregation tx time + block-ack time. */
1712 __le16 wireless_media_time; /* uSecs */
1713
1714 __le16 reserved;
1715 __le32 pa_power1; /* RF power amplifier measurement (not used) */
1716 __le32 pa_power2;
1717
1718 /*
1719 * For non-agg: frame status TX_STATUS_*
1720 * For agg: status of 1st frame, AGG_TX_STATE_*; other frame status
1721 * fields follow this one, up to frame_count.
1722 * Bit fields:
1723 * 11- 0: AGG_TX_STATE_* status code
1724 * 15-12: Retry count for 1st frame in aggregation (retries
1725 * occur if tx failed for this frame when it was a
1726 * member of a previous aggregation block). If rate
1727 * scaling is used, retry count indicates the rate
1728 * table entry used for all frames in the new agg.
1729 * 31-16: Sequence # for this frame's Tx cmd (not SSN!)
1730 */
1731 union {
1732 __le32 status;
1733 struct agg_tx_status agg_status[0]; /* for each agg frame */
1734 } u;
1735} __packed;
1736
1737/*
1738 * REPLY_COMPRESSED_BA = 0xc5 (response only, not a command)
1739 *
1740 * Reports Block-Acknowledge from recipient station
1741 */
1742struct iwl_compressed_ba_resp {
1743 __le32 sta_addr_lo32;
1744 __le16 sta_addr_hi16;
1745 __le16 reserved;
1746
1747 /* Index of recipient (BA-sending) station in uCode's station table */
1748 u8 sta_id;
1749 u8 tid;
1750 __le16 seq_ctl;
1751 __le64 bitmap;
1752 __le16 scd_flow;
1753 __le16 scd_ssn;
1754} __packed;
1755
1756/*
1757 * REPLY_TX_PWR_TABLE_CMD = 0x97 (command, has simple generic response)
1758 *
1759 * See details under "TXPOWER" in iwl-4965-hw.h.
1760 */
1761
1762struct iwl3945_txpowertable_cmd {
1763 u8 band; /* 0: 5 GHz, 1: 2.4 GHz */
1764 u8 reserved;
1765 __le16 channel;
1766 struct iwl3945_power_per_rate power[IWL_MAX_RATES];
1767} __packed;
1768
1769struct iwl4965_txpowertable_cmd {
1770 u8 band; /* 0: 5 GHz, 1: 2.4 GHz */
1771 u8 reserved;
1772 __le16 channel;
1773 struct iwl4965_tx_power_db tx_power;
1774} __packed;
1775
1776
1777/**
1778 * struct iwl3945_rate_scaling_cmd - Rate Scaling Command & Response
1779 *
1780 * REPLY_RATE_SCALE = 0x47 (command, has simple generic response)
1781 *
1782 * NOTE: The table of rates passed to the uCode via the
1783 * RATE_SCALE command sets up the corresponding order of
1784 * rates used for all related commands, including rate
1785 * masks, etc.
1786 *
1787 * For example, if you set 9MB (PLCP 0x0f) as the first
1788 * rate in the rate table, the bit mask for that rate
1789 * when passed through ofdm_basic_rates on the REPLY_RXON
1790 * command would be bit 0 (1 << 0)
1791 */
1792struct iwl3945_rate_scaling_info {
1793 __le16 rate_n_flags;
1794 u8 try_cnt;
1795 u8 next_rate_index;
1796} __packed;
1797
1798struct iwl3945_rate_scaling_cmd {
1799 u8 table_id;
1800 u8 reserved[3];
1801 struct iwl3945_rate_scaling_info table[IWL_MAX_RATES];
1802} __packed;
1803
1804
1805/*RS_NEW_API: only TLC_RTS remains and moved to bit 0 */
1806#define LINK_QUAL_FLAGS_SET_STA_TLC_RTS_MSK (1 << 0)
1807
1808/* # of EDCA prioritized tx fifos */
1809#define LINK_QUAL_AC_NUM AC_NUM
1810
1811/* # entries in rate scale table to support Tx retries */
1812#define LINK_QUAL_MAX_RETRY_NUM 16
1813
1814/* Tx antenna selection values */
1815#define LINK_QUAL_ANT_A_MSK (1 << 0)
1816#define LINK_QUAL_ANT_B_MSK (1 << 1)
1817#define LINK_QUAL_ANT_MSK (LINK_QUAL_ANT_A_MSK|LINK_QUAL_ANT_B_MSK)
1818
1819
1820/**
1821 * struct iwl_link_qual_general_params
1822 *
1823 * Used in REPLY_TX_LINK_QUALITY_CMD
1824 */
1825struct iwl_link_qual_general_params {
1826 u8 flags;
1827
1828 /* No entries at or above this (driver chosen) index contain MIMO */
1829 u8 mimo_delimiter;
1830
1831 /* Best single antenna to use for single stream (legacy, SISO). */
1832 u8 single_stream_ant_msk; /* LINK_QUAL_ANT_* */
1833
1834 /* Best antennas to use for MIMO (unused for 4965, assumes both). */
1835 u8 dual_stream_ant_msk; /* LINK_QUAL_ANT_* */
1836
1837 /*
1838 * If driver needs to use different initial rates for different
1839 * EDCA QOS access categories (as implemented by tx fifos 0-3),
1840 * this table will set that up, by indicating the indexes in the
1841 * rs_table[LINK_QUAL_MAX_RETRY_NUM] rate table at which to start.
1842 * Otherwise, driver should set all entries to 0.
1843 *
1844 * Entry usage:
1845 * 0 = Background, 1 = Best Effort (normal), 2 = Video, 3 = Voice
1846 * TX FIFOs above 3 use same value (typically 0) as TX FIFO 3.
1847 */
1848 u8 start_rate_index[LINK_QUAL_AC_NUM];
1849} __packed;
1850
1851#define LINK_QUAL_AGG_TIME_LIMIT_DEF (4000) /* 4 milliseconds */
1852#define LINK_QUAL_AGG_TIME_LIMIT_MAX (8000)
1853#define LINK_QUAL_AGG_TIME_LIMIT_MIN (100)
1854
1855#define LINK_QUAL_AGG_DISABLE_START_DEF (3)
1856#define LINK_QUAL_AGG_DISABLE_START_MAX (255)
1857#define LINK_QUAL_AGG_DISABLE_START_MIN (0)
1858
1859#define LINK_QUAL_AGG_FRAME_LIMIT_DEF (31)
1860#define LINK_QUAL_AGG_FRAME_LIMIT_MAX (63)
1861#define LINK_QUAL_AGG_FRAME_LIMIT_MIN (0)
1862
1863/**
1864 * struct iwl_link_qual_agg_params
1865 *
1866 * Used in REPLY_TX_LINK_QUALITY_CMD
1867 */
1868struct iwl_link_qual_agg_params {
1869
1870 /*
1871 *Maximum number of uSec in aggregation.
1872 * default set to 4000 (4 milliseconds) if not configured in .cfg
1873 */
1874 __le16 agg_time_limit;
1875
1876 /*
1877 * Number of Tx retries allowed for a frame, before that frame will
1878 * no longer be considered for the start of an aggregation sequence
1879 * (scheduler will then try to tx it as single frame).
1880 * Driver should set this to 3.
1881 */
1882 u8 agg_dis_start_th;
1883
1884 /*
1885 * Maximum number of frames in aggregation.
1886 * 0 = no limit (default). 1 = no aggregation.
1887 * Other values = max # frames in aggregation.
1888 */
1889 u8 agg_frame_cnt_limit;
1890
1891 __le32 reserved;
1892} __packed;
1893
1894/*
1895 * REPLY_TX_LINK_QUALITY_CMD = 0x4e (command, has simple generic response)
1896 *
1897 * For 4965 devices only; 3945 uses REPLY_RATE_SCALE.
1898 *
1899 * Each station in the 4965 device's internal station table has its own table
1900 * of 16
1901 * Tx rates and modulation modes (e.g. legacy/SISO/MIMO) for retrying Tx when
1902 * an ACK is not received. This command replaces the entire table for
1903 * one station.
1904 *
1905 * NOTE: Station must already be in 4965 device's station table.
1906 * Use REPLY_ADD_STA.
1907 *
1908 * The rate scaling procedures described below work well. Of course, other
1909 * procedures are possible, and may work better for particular environments.
1910 *
1911 *
1912 * FILLING THE RATE TABLE
1913 *
1914 * Given a particular initial rate and mode, as determined by the rate
1915 * scaling algorithm described below, the Linux driver uses the following
1916 * formula to fill the rs_table[LINK_QUAL_MAX_RETRY_NUM] rate table in the
1917 * Link Quality command:
1918 *
1919 *
1920 * 1) If using High-throughput (HT) (SISO or MIMO) initial rate:
1921 * a) Use this same initial rate for first 3 entries.
1922 * b) Find next lower available rate using same mode (SISO or MIMO),
1923 * use for next 3 entries. If no lower rate available, switch to
1924 * legacy mode (no HT40 channel, no MIMO, no short guard interval).
1925 * c) If using MIMO, set command's mimo_delimiter to number of entries
1926 * using MIMO (3 or 6).
1927 * d) After trying 2 HT rates, switch to legacy mode (no HT40 channel,
1928 * no MIMO, no short guard interval), at the next lower bit rate
1929 * (e.g. if second HT bit rate was 54, try 48 legacy), and follow
1930 * legacy procedure for remaining table entries.
1931 *
1932 * 2) If using legacy initial rate:
1933 * a) Use the initial rate for only one entry.
1934 * b) For each following entry, reduce the rate to next lower available
1935 * rate, until reaching the lowest available rate.
1936 * c) When reducing rate, also switch antenna selection.
1937 * d) Once lowest available rate is reached, repeat this rate until
1938 * rate table is filled (16 entries), switching antenna each entry.
1939 *
1940 *
1941 * ACCUMULATING HISTORY
1942 *
1943 * The rate scaling algorithm for 4965 devices, as implemented in Linux driver,
1944 * uses two sets of frame Tx success history: One for the current/active
1945 * modulation mode, and one for a speculative/search mode that is being
1946 * attempted. If the speculative mode turns out to be more effective (i.e.
1947 * actual transfer rate is better), then the driver continues to use the
1948 * speculative mode as the new current active mode.
1949 *
1950 * Each history set contains, separately for each possible rate, data for a
1951 * sliding window of the 62 most recent tx attempts at that rate. The data
1952 * includes a shifting bitmap of success(1)/failure(0), and sums of successful
1953 * and attempted frames, from which the driver can additionally calculate a
1954 * success ratio (success / attempted) and number of failures
1955 * (attempted - success), and control the size of the window (attempted).
1956 * The driver uses the bit map to remove successes from the success sum, as
1957 * the oldest tx attempts fall out of the window.
1958 *
1959 * When the 4965 device makes multiple tx attempts for a given frame, each
1960 * attempt might be at a different rate, and have different modulation
1961 * characteristics (e.g. antenna, fat channel, short guard interval), as set
1962 * up in the rate scaling table in the Link Quality command. The driver must
1963 * determine which rate table entry was used for each tx attempt, to determine
1964 * which rate-specific history to update, and record only those attempts that
1965 * match the modulation characteristics of the history set.
1966 *
1967 * When using block-ack (aggregation), all frames are transmitted at the same
1968 * rate, since there is no per-attempt acknowledgment from the destination
1969 * station. The Tx response struct iwl_tx_resp indicates the Tx rate in
1970 * rate_n_flags field. After receiving a block-ack, the driver can update
1971 * history for the entire block all at once.
1972 *
1973 *
1974 * FINDING BEST STARTING RATE:
1975 *
1976 * When working with a selected initial modulation mode (see below), the
1977 * driver attempts to find a best initial rate. The initial rate is the
1978 * first entry in the Link Quality command's rate table.
1979 *
1980 * 1) Calculate actual throughput (success ratio * expected throughput, see
1981 * table below) for current initial rate. Do this only if enough frames
1982 * have been attempted to make the value meaningful: at least 6 failed
1983 * tx attempts, or at least 8 successes. If not enough, don't try rate
1984 * scaling yet.
1985 *
1986 * 2) Find available rates adjacent to current initial rate. Available means:
1987 * a) supported by hardware &&
1988 * b) supported by association &&
1989 * c) within any constraints selected by user
1990 *
1991 * 3) Gather measured throughputs for adjacent rates. These might not have
1992 * enough history to calculate a throughput. That's okay, we might try
1993 * using one of them anyway!
1994 *
1995 * 4) Try decreasing rate if, for current rate:
1996 * a) success ratio is < 15% ||
1997 * b) lower adjacent rate has better measured throughput ||
1998 * c) higher adjacent rate has worse throughput, and lower is unmeasured
1999 *
2000 * As a sanity check, if decrease was determined above, leave rate
2001 * unchanged if:
2002 * a) lower rate unavailable
2003 * b) success ratio at current rate > 85% (very good)
2004 * c) current measured throughput is better than expected throughput
2005 * of lower rate (under perfect 100% tx conditions, see table below)
2006 *
2007 * 5) Try increasing rate if, for current rate:
2008 * a) success ratio is < 15% ||
2009 * b) both adjacent rates' throughputs are unmeasured (try it!) ||
2010 * b) higher adjacent rate has better measured throughput ||
2011 * c) lower adjacent rate has worse throughput, and higher is unmeasured
2012 *
2013 * As a sanity check, if increase was determined above, leave rate
2014 * unchanged if:
2015 * a) success ratio at current rate < 70%. This is not particularly
2016 * good performance; higher rate is sure to have poorer success.
2017 *
2018 * 6) Re-evaluate the rate after each tx frame. If working with block-
2019 * acknowledge, history and statistics may be calculated for the entire
2020 * block (including prior history that fits within the history windows),
2021 * before re-evaluation.
2022 *
2023 * FINDING BEST STARTING MODULATION MODE:
2024 *
2025 * After working with a modulation mode for a "while" (and doing rate scaling),
2026 * the driver searches for a new initial mode in an attempt to improve
2027 * throughput. The "while" is measured by numbers of attempted frames:
2028 *
2029 * For legacy mode, search for new mode after:
2030 * 480 successful frames, or 160 failed frames
2031 * For high-throughput modes (SISO or MIMO), search for new mode after:
2032 * 4500 successful frames, or 400 failed frames
2033 *
2034 * Mode switch possibilities are (3 for each mode):
2035 *
2036 * For legacy:
2037 * Change antenna, try SISO (if HT association), try MIMO (if HT association)
2038 * For SISO:
2039 * Change antenna, try MIMO, try shortened guard interval (SGI)
2040 * For MIMO:
2041 * Try SISO antenna A, SISO antenna B, try shortened guard interval (SGI)
2042 *
2043 * When trying a new mode, use the same bit rate as the old/current mode when
2044 * trying antenna switches and shortened guard interval. When switching to
2045 * SISO from MIMO or legacy, or to MIMO from SISO or legacy, use a rate
2046 * for which the expected throughput (under perfect conditions) is about the
2047 * same or slightly better than the actual measured throughput delivered by
2048 * the old/current mode.
2049 *
2050 * Actual throughput can be estimated by multiplying the expected throughput
2051 * by the success ratio (successful / attempted tx frames). Frame size is
2052 * not considered in this calculation; it assumes that frame size will average
2053 * out to be fairly consistent over several samples. The following are
2054 * metric values for expected throughput assuming 100% success ratio.
2055 * Only G band has support for CCK rates:
2056 *
2057 * RATE: 1 2 5 11 6 9 12 18 24 36 48 54 60
2058 *
2059 * G: 7 13 35 58 40 57 72 98 121 154 177 186 186
2060 * A: 0 0 0 0 40 57 72 98 121 154 177 186 186
2061 * SISO 20MHz: 0 0 0 0 42 42 76 102 124 159 183 193 202
2062 * SGI SISO 20MHz: 0 0 0 0 46 46 82 110 132 168 192 202 211
2063 * MIMO 20MHz: 0 0 0 0 74 74 123 155 179 214 236 244 251
2064 * SGI MIMO 20MHz: 0 0 0 0 81 81 131 164 188 222 243 251 257
2065 * SISO 40MHz: 0 0 0 0 77 77 127 160 184 220 242 250 257
2066 * SGI SISO 40MHz: 0 0 0 0 83 83 135 169 193 229 250 257 264
2067 * MIMO 40MHz: 0 0 0 0 123 123 182 214 235 264 279 285 289
2068 * SGI MIMO 40MHz: 0 0 0 0 131 131 191 222 242 270 284 289 293
2069 *
2070 * After the new mode has been tried for a short while (minimum of 6 failed
2071 * frames or 8 successful frames), compare success ratio and actual throughput
2072 * estimate of the new mode with the old. If either is better with the new
2073 * mode, continue to use the new mode.
2074 *
2075 * Continue comparing modes until all 3 possibilities have been tried.
2076 * If moving from legacy to HT, try all 3 possibilities from the new HT
2077 * mode. After trying all 3, a best mode is found. Continue to use this mode
2078 * for the longer "while" described above (e.g. 480 successful frames for
2079 * legacy), and then repeat the search process.
2080 *
2081 */
2082struct iwl_link_quality_cmd {
2083
2084 /* Index of destination/recipient station in uCode's station table */
2085 u8 sta_id;
2086 u8 reserved1;
2087 __le16 control; /* not used */
2088 struct iwl_link_qual_general_params general_params;
2089 struct iwl_link_qual_agg_params agg_params;
2090
2091 /*
2092 * Rate info; when using rate-scaling, Tx command's initial_rate_index
2093 * specifies 1st Tx rate attempted, via index into this table.
2094 * 4965 devices works its way through table when retrying Tx.
2095 */
2096 struct {
2097 __le32 rate_n_flags; /* RATE_MCS_*, IWL_RATE_* */
2098 } rs_table[LINK_QUAL_MAX_RETRY_NUM];
2099 __le32 reserved2;
2100} __packed;
2101
2102/*
2103 * BT configuration enable flags:
2104 * bit 0 - 1: BT channel announcement enabled
2105 * 0: disable
2106 * bit 1 - 1: priority of BT device enabled
2107 * 0: disable
2108 */
2109#define BT_COEX_DISABLE (0x0)
2110#define BT_ENABLE_CHANNEL_ANNOUNCE BIT(0)
2111#define BT_ENABLE_PRIORITY BIT(1)
2112
2113#define BT_COEX_ENABLE (BT_ENABLE_CHANNEL_ANNOUNCE | BT_ENABLE_PRIORITY)
2114
2115#define BT_LEAD_TIME_DEF (0x1E)
2116
2117#define BT_MAX_KILL_DEF (0x5)
2118
2119/*
2120 * REPLY_BT_CONFIG = 0x9b (command, has simple generic response)
2121 *
2122 * 3945 and 4965 devices support hardware handshake with Bluetooth device on
2123 * same platform. Bluetooth device alerts wireless device when it will Tx;
2124 * wireless device can delay or kill its own Tx to accommodate.
2125 */
2126struct iwl_bt_cmd {
2127 u8 flags;
2128 u8 lead_time;
2129 u8 max_kill;
2130 u8 reserved;
2131 __le32 kill_ack_mask;
2132 __le32 kill_cts_mask;
2133} __packed;
2134
2135
2136/******************************************************************************
2137 * (6)
2138 * Spectrum Management (802.11h) Commands, Responses, Notifications:
2139 *
2140 *****************************************************************************/
2141
2142/*
2143 * Spectrum Management
2144 */
2145#define MEASUREMENT_FILTER_FLAG (RXON_FILTER_PROMISC_MSK | \
2146 RXON_FILTER_CTL2HOST_MSK | \
2147 RXON_FILTER_ACCEPT_GRP_MSK | \
2148 RXON_FILTER_DIS_DECRYPT_MSK | \
2149 RXON_FILTER_DIS_GRP_DECRYPT_MSK | \
2150 RXON_FILTER_ASSOC_MSK | \
2151 RXON_FILTER_BCON_AWARE_MSK)
2152
2153struct iwl_measure_channel {
2154 __le32 duration; /* measurement duration in extended beacon
2155 * format */
2156 u8 channel; /* channel to measure */
2157 u8 type; /* see enum iwl_measure_type */
2158 __le16 reserved;
2159} __packed;
2160
2161/*
2162 * REPLY_SPECTRUM_MEASUREMENT_CMD = 0x74 (command)
2163 */
2164struct iwl_spectrum_cmd {
2165 __le16 len; /* number of bytes starting from token */
2166 u8 token; /* token id */
2167 u8 id; /* measurement id -- 0 or 1 */
2168 u8 origin; /* 0 = TGh, 1 = other, 2 = TGk */
2169 u8 periodic; /* 1 = periodic */
2170 __le16 path_loss_timeout;
2171 __le32 start_time; /* start time in extended beacon format */
2172 __le32 reserved2;
2173 __le32 flags; /* rxon flags */
2174 __le32 filter_flags; /* rxon filter flags */
2175 __le16 channel_count; /* minimum 1, maximum 10 */
2176 __le16 reserved3;
2177 struct iwl_measure_channel channels[10];
2178} __packed;
2179
2180/*
2181 * REPLY_SPECTRUM_MEASUREMENT_CMD = 0x74 (response)
2182 */
2183struct iwl_spectrum_resp {
2184 u8 token;
2185 u8 id; /* id of the prior command replaced, or 0xff */
2186 __le16 status; /* 0 - command will be handled
2187 * 1 - cannot handle (conflicts with another
2188 * measurement) */
2189} __packed;
2190
2191enum iwl_measurement_state {
2192 IWL_MEASUREMENT_START = 0,
2193 IWL_MEASUREMENT_STOP = 1,
2194};
2195
2196enum iwl_measurement_status {
2197 IWL_MEASUREMENT_OK = 0,
2198 IWL_MEASUREMENT_CONCURRENT = 1,
2199 IWL_MEASUREMENT_CSA_CONFLICT = 2,
2200 IWL_MEASUREMENT_TGH_CONFLICT = 3,
2201 /* 4-5 reserved */
2202 IWL_MEASUREMENT_STOPPED = 6,
2203 IWL_MEASUREMENT_TIMEOUT = 7,
2204 IWL_MEASUREMENT_PERIODIC_FAILED = 8,
2205};
2206
2207#define NUM_ELEMENTS_IN_HISTOGRAM 8
2208
2209struct iwl_measurement_histogram {
2210 __le32 ofdm[NUM_ELEMENTS_IN_HISTOGRAM]; /* in 0.8usec counts */
2211 __le32 cck[NUM_ELEMENTS_IN_HISTOGRAM]; /* in 1usec counts */
2212} __packed;
2213
2214/* clear channel availability counters */
2215struct iwl_measurement_cca_counters {
2216 __le32 ofdm;
2217 __le32 cck;
2218} __packed;
2219
2220enum iwl_measure_type {
2221 IWL_MEASURE_BASIC = (1 << 0),
2222 IWL_MEASURE_CHANNEL_LOAD = (1 << 1),
2223 IWL_MEASURE_HISTOGRAM_RPI = (1 << 2),
2224 IWL_MEASURE_HISTOGRAM_NOISE = (1 << 3),
2225 IWL_MEASURE_FRAME = (1 << 4),
2226 /* bits 5:6 are reserved */
2227 IWL_MEASURE_IDLE = (1 << 7),
2228};
2229
2230/*
2231 * SPECTRUM_MEASURE_NOTIFICATION = 0x75 (notification only, not a command)
2232 */
2233struct iwl_spectrum_notification {
2234 u8 id; /* measurement id -- 0 or 1 */
2235 u8 token;
2236 u8 channel_index; /* index in measurement channel list */
2237 u8 state; /* 0 - start, 1 - stop */
2238 __le32 start_time; /* lower 32-bits of TSF */
2239 u8 band; /* 0 - 5.2GHz, 1 - 2.4GHz */
2240 u8 channel;
2241 u8 type; /* see enum iwl_measurement_type */
2242 u8 reserved1;
2243 /* NOTE: cca_ofdm, cca_cck, basic_type, and histogram are only only
2244 * valid if applicable for measurement type requested. */
2245 __le32 cca_ofdm; /* cca fraction time in 40Mhz clock periods */
2246 __le32 cca_cck; /* cca fraction time in 44Mhz clock periods */
2247 __le32 cca_time; /* channel load time in usecs */
2248 u8 basic_type; /* 0 - bss, 1 - ofdm preamble, 2 -
2249 * unidentified */
2250 u8 reserved2[3];
2251 struct iwl_measurement_histogram histogram;
2252 __le32 stop_time; /* lower 32-bits of TSF */
2253 __le32 status; /* see iwl_measurement_status */
2254} __packed;
2255
2256/******************************************************************************
2257 * (7)
2258 * Power Management Commands, Responses, Notifications:
2259 *
2260 *****************************************************************************/
2261
2262/**
2263 * struct iwl_powertable_cmd - Power Table Command
2264 * @flags: See below:
2265 *
2266 * POWER_TABLE_CMD = 0x77 (command, has simple generic response)
2267 *
2268 * PM allow:
2269 * bit 0 - '0' Driver not allow power management
2270 * '1' Driver allow PM (use rest of parameters)
2271 *
2272 * uCode send sleep notifications:
2273 * bit 1 - '0' Don't send sleep notification
2274 * '1' send sleep notification (SEND_PM_NOTIFICATION)
2275 *
2276 * Sleep over DTIM
2277 * bit 2 - '0' PM have to walk up every DTIM
2278 * '1' PM could sleep over DTIM till listen Interval.
2279 *
2280 * PCI power managed
2281 * bit 3 - '0' (PCI_CFG_LINK_CTRL & 0x1)
2282 * '1' !(PCI_CFG_LINK_CTRL & 0x1)
2283 *
2284 * Fast PD
2285 * bit 4 - '1' Put radio to sleep when receiving frame for others
2286 *
2287 * Force sleep Modes
2288 * bit 31/30- '00' use both mac/xtal sleeps
2289 * '01' force Mac sleep
2290 * '10' force xtal sleep
2291 * '11' Illegal set
2292 *
2293 * NOTE: if sleep_interval[SLEEP_INTRVL_TABLE_SIZE-1] > DTIM period then
2294 * ucode assume sleep over DTIM is allowed and we don't need to wake up
2295 * for every DTIM.
2296 */
2297#define IWL_POWER_VEC_SIZE 5
2298
2299#define IWL_POWER_DRIVER_ALLOW_SLEEP_MSK cpu_to_le16(BIT(0))
2300#define IWL_POWER_PCI_PM_MSK cpu_to_le16(BIT(3))
2301
2302struct iwl3945_powertable_cmd {
2303 __le16 flags;
2304 u8 reserved[2];
2305 __le32 rx_data_timeout;
2306 __le32 tx_data_timeout;
2307 __le32 sleep_interval[IWL_POWER_VEC_SIZE];
2308} __packed;
2309
2310struct iwl_powertable_cmd {
2311 __le16 flags;
2312 u8 keep_alive_seconds; /* 3945 reserved */
2313 u8 debug_flags; /* 3945 reserved */
2314 __le32 rx_data_timeout;
2315 __le32 tx_data_timeout;
2316 __le32 sleep_interval[IWL_POWER_VEC_SIZE];
2317 __le32 keep_alive_beacons;
2318} __packed;
2319
2320/*
2321 * PM_SLEEP_NOTIFICATION = 0x7A (notification only, not a command)
2322 * all devices identical.
2323 */
2324struct iwl_sleep_notification {
2325 u8 pm_sleep_mode;
2326 u8 pm_wakeup_src;
2327 __le16 reserved;
2328 __le32 sleep_time;
2329 __le32 tsf_low;
2330 __le32 bcon_timer;
2331} __packed;
2332
2333/* Sleep states. all devices identical. */
2334enum {
2335 IWL_PM_NO_SLEEP = 0,
2336 IWL_PM_SLP_MAC = 1,
2337 IWL_PM_SLP_FULL_MAC_UNASSOCIATE = 2,
2338 IWL_PM_SLP_FULL_MAC_CARD_STATE = 3,
2339 IWL_PM_SLP_PHY = 4,
2340 IWL_PM_SLP_REPENT = 5,
2341 IWL_PM_WAKEUP_BY_TIMER = 6,
2342 IWL_PM_WAKEUP_BY_DRIVER = 7,
2343 IWL_PM_WAKEUP_BY_RFKILL = 8,
2344 /* 3 reserved */
2345 IWL_PM_NUM_OF_MODES = 12,
2346};
2347
2348/*
2349 * CARD_STATE_NOTIFICATION = 0xa1 (notification only, not a command)
2350 */
2351struct iwl_card_state_notif {
2352 __le32 flags;
2353} __packed;
2354
2355#define HW_CARD_DISABLED 0x01
2356#define SW_CARD_DISABLED 0x02
2357#define CT_CARD_DISABLED 0x04
2358#define RXON_CARD_DISABLED 0x10
2359
2360struct iwl_ct_kill_config {
2361 __le32 reserved;
2362 __le32 critical_temperature_M;
2363 __le32 critical_temperature_R;
2364} __packed;
2365
2366/******************************************************************************
2367 * (8)
2368 * Scan Commands, Responses, Notifications:
2369 *
2370 *****************************************************************************/
2371
2372#define SCAN_CHANNEL_TYPE_PASSIVE cpu_to_le32(0)
2373#define SCAN_CHANNEL_TYPE_ACTIVE cpu_to_le32(1)
2374
2375/**
2376 * struct iwl_scan_channel - entry in REPLY_SCAN_CMD channel table
2377 *
2378 * One for each channel in the scan list.
2379 * Each channel can independently select:
2380 * 1) SSID for directed active scans
2381 * 2) Txpower setting (for rate specified within Tx command)
2382 * 3) How long to stay on-channel (behavior may be modified by quiet_time,
2383 * quiet_plcp_th, good_CRC_th)
2384 *
2385 * To avoid uCode errors, make sure the following are true (see comments
2386 * under struct iwl_scan_cmd about max_out_time and quiet_time):
2387 * 1) If using passive_dwell (i.e. passive_dwell != 0):
2388 * active_dwell <= passive_dwell (< max_out_time if max_out_time != 0)
2389 * 2) quiet_time <= active_dwell
2390 * 3) If restricting off-channel time (i.e. max_out_time !=0):
2391 * passive_dwell < max_out_time
2392 * active_dwell < max_out_time
2393 */
2394struct iwl3945_scan_channel {
2395 /*
2396 * type is defined as:
2397 * 0:0 1 = active, 0 = passive
2398 * 1:4 SSID direct bit map; if a bit is set, then corresponding
2399 * SSID IE is transmitted in probe request.
2400 * 5:7 reserved
2401 */
2402 u8 type;
2403 u8 channel; /* band is selected by iwl3945_scan_cmd "flags" field */
2404 struct iwl3945_tx_power tpc;
2405 __le16 active_dwell; /* in 1024-uSec TU (time units), typ 5-50 */
2406 __le16 passive_dwell; /* in 1024-uSec TU (time units), typ 20-500 */
2407} __packed;
2408
2409/* set number of direct probes u8 type */
2410#define IWL39_SCAN_PROBE_MASK(n) ((BIT(n) | (BIT(n) - BIT(1))))
2411
2412struct iwl_scan_channel {
2413 /*
2414 * type is defined as:
2415 * 0:0 1 = active, 0 = passive
2416 * 1:20 SSID direct bit map; if a bit is set, then corresponding
2417 * SSID IE is transmitted in probe request.
2418 * 21:31 reserved
2419 */
2420 __le32 type;
2421 __le16 channel; /* band is selected by iwl_scan_cmd "flags" field */
2422 u8 tx_gain; /* gain for analog radio */
2423 u8 dsp_atten; /* gain for DSP */
2424 __le16 active_dwell; /* in 1024-uSec TU (time units), typ 5-50 */
2425 __le16 passive_dwell; /* in 1024-uSec TU (time units), typ 20-500 */
2426} __packed;
2427
2428/* set number of direct probes __le32 type */
2429#define IWL_SCAN_PROBE_MASK(n) cpu_to_le32((BIT(n) | (BIT(n) - BIT(1))))
2430
2431/**
2432 * struct iwl_ssid_ie - directed scan network information element
2433 *
2434 * Up to 20 of these may appear in REPLY_SCAN_CMD (Note: Only 4 are in
2435 * 3945 SCAN api), selected by "type" bit field in struct iwl_scan_channel;
2436 * each channel may select different ssids from among the 20 (4) entries.
2437 * SSID IEs get transmitted in reverse order of entry.
2438 */
2439struct iwl_ssid_ie {
2440 u8 id;
2441 u8 len;
2442 u8 ssid[32];
2443} __packed;
2444
2445#define PROBE_OPTION_MAX_3945 4
2446#define PROBE_OPTION_MAX 20
2447#define TX_CMD_LIFE_TIME_INFINITE cpu_to_le32(0xFFFFFFFF)
2448#define IWL_GOOD_CRC_TH_DISABLED 0
2449#define IWL_GOOD_CRC_TH_DEFAULT cpu_to_le16(1)
2450#define IWL_GOOD_CRC_TH_NEVER cpu_to_le16(0xffff)
2451#define IWL_MAX_SCAN_SIZE 1024
2452#define IWL_MAX_CMD_SIZE 4096
2453
2454/*
2455 * REPLY_SCAN_CMD = 0x80 (command)
2456 *
2457 * The hardware scan command is very powerful; the driver can set it up to
2458 * maintain (relatively) normal network traffic while doing a scan in the
2459 * background. The max_out_time and suspend_time control the ratio of how
2460 * long the device stays on an associated network channel ("service channel")
2461 * vs. how long it's away from the service channel, i.e. tuned to other channels
2462 * for scanning.
2463 *
2464 * max_out_time is the max time off-channel (in usec), and suspend_time
2465 * is how long (in "extended beacon" format) that the scan is "suspended"
2466 * after returning to the service channel. That is, suspend_time is the
2467 * time that we stay on the service channel, doing normal work, between
2468 * scan segments. The driver may set these parameters differently to support
2469 * scanning when associated vs. not associated, and light vs. heavy traffic
2470 * loads when associated.
2471 *
2472 * After receiving this command, the device's scan engine does the following;
2473 *
2474 * 1) Sends SCAN_START notification to driver
2475 * 2) Checks to see if it has time to do scan for one channel
2476 * 3) Sends NULL packet, with power-save (PS) bit set to 1,
2477 * to tell AP that we're going off-channel
2478 * 4) Tunes to first channel in scan list, does active or passive scan
2479 * 5) Sends SCAN_RESULT notification to driver
2480 * 6) Checks to see if it has time to do scan on *next* channel in list
2481 * 7) Repeats 4-6 until it no longer has time to scan the next channel
2482 * before max_out_time expires
2483 * 8) Returns to service channel
2484 * 9) Sends NULL packet with PS=0 to tell AP that we're back
2485 * 10) Stays on service channel until suspend_time expires
2486 * 11) Repeats entire process 2-10 until list is complete
2487 * 12) Sends SCAN_COMPLETE notification
2488 *
2489 * For fast, efficient scans, the scan command also has support for staying on
2490 * a channel for just a short time, if doing active scanning and getting no
2491 * responses to the transmitted probe request. This time is controlled by
2492 * quiet_time, and the number of received packets below which a channel is
2493 * considered "quiet" is controlled by quiet_plcp_threshold.
2494 *
2495 * For active scanning on channels that have regulatory restrictions against
2496 * blindly transmitting, the scan can listen before transmitting, to make sure
2497 * that there is already legitimate activity on the channel. If enough
2498 * packets are cleanly received on the channel (controlled by good_CRC_th,
2499 * typical value 1), the scan engine starts transmitting probe requests.
2500 *
2501 * Driver must use separate scan commands for 2.4 vs. 5 GHz bands.
2502 *
2503 * To avoid uCode errors, see timing restrictions described under
2504 * struct iwl_scan_channel.
2505 */
2506
2507struct iwl3945_scan_cmd {
2508 __le16 len;
2509 u8 reserved0;
2510 u8 channel_count; /* # channels in channel list */
2511 __le16 quiet_time; /* dwell only this # millisecs on quiet channel
2512 * (only for active scan) */
2513 __le16 quiet_plcp_th; /* quiet chnl is < this # pkts (typ. 1) */
2514 __le16 good_CRC_th; /* passive -> active promotion threshold */
2515 __le16 reserved1;
2516 __le32 max_out_time; /* max usec to be away from associated (service)
2517 * channel */
2518 __le32 suspend_time; /* pause scan this long (in "extended beacon
2519 * format") when returning to service channel:
2520 * 3945; 31:24 # beacons, 19:0 additional usec,
2521 * 4965; 31:22 # beacons, 21:0 additional usec.
2522 */
2523 __le32 flags; /* RXON_FLG_* */
2524 __le32 filter_flags; /* RXON_FILTER_* */
2525
2526 /* For active scans (set to all-0s for passive scans).
2527 * Does not include payload. Must specify Tx rate; no rate scaling. */
2528 struct iwl3945_tx_cmd tx_cmd;
2529
2530 /* For directed active scans (set to all-0s otherwise) */
2531 struct iwl_ssid_ie direct_scan[PROBE_OPTION_MAX_3945];
2532
2533 /*
2534 * Probe request frame, followed by channel list.
2535 *
2536 * Size of probe request frame is specified by byte count in tx_cmd.
2537 * Channel list follows immediately after probe request frame.
2538 * Number of channels in list is specified by channel_count.
2539 * Each channel in list is of type:
2540 *
2541 * struct iwl3945_scan_channel channels[0];
2542 *
2543 * NOTE: Only one band of channels can be scanned per pass. You
2544 * must not mix 2.4GHz channels and 5.2GHz channels, and you must wait
2545 * for one scan to complete (i.e. receive SCAN_COMPLETE_NOTIFICATION)
2546 * before requesting another scan.
2547 */
2548 u8 data[0];
2549} __packed;
2550
2551struct iwl_scan_cmd {
2552 __le16 len;
2553 u8 reserved0;
2554 u8 channel_count; /* # channels in channel list */
2555 __le16 quiet_time; /* dwell only this # millisecs on quiet channel
2556 * (only for active scan) */
2557 __le16 quiet_plcp_th; /* quiet chnl is < this # pkts (typ. 1) */
2558 __le16 good_CRC_th; /* passive -> active promotion threshold */
2559 __le16 rx_chain; /* RXON_RX_CHAIN_* */
2560 __le32 max_out_time; /* max usec to be away from associated (service)
2561 * channel */
2562 __le32 suspend_time; /* pause scan this long (in "extended beacon
2563 * format") when returning to service chnl:
2564 * 3945; 31:24 # beacons, 19:0 additional usec,
2565 * 4965; 31:22 # beacons, 21:0 additional usec.
2566 */
2567 __le32 flags; /* RXON_FLG_* */
2568 __le32 filter_flags; /* RXON_FILTER_* */
2569
2570 /* For active scans (set to all-0s for passive scans).
2571 * Does not include payload. Must specify Tx rate; no rate scaling. */
2572 struct iwl_tx_cmd tx_cmd;
2573
2574 /* For directed active scans (set to all-0s otherwise) */
2575 struct iwl_ssid_ie direct_scan[PROBE_OPTION_MAX];
2576
2577 /*
2578 * Probe request frame, followed by channel list.
2579 *
2580 * Size of probe request frame is specified by byte count in tx_cmd.
2581 * Channel list follows immediately after probe request frame.
2582 * Number of channels in list is specified by channel_count.
2583 * Each channel in list is of type:
2584 *
2585 * struct iwl_scan_channel channels[0];
2586 *
2587 * NOTE: Only one band of channels can be scanned per pass. You
2588 * must not mix 2.4GHz channels and 5.2GHz channels, and you must wait
2589 * for one scan to complete (i.e. receive SCAN_COMPLETE_NOTIFICATION)
2590 * before requesting another scan.
2591 */
2592 u8 data[0];
2593} __packed;
2594
2595/* Can abort will notify by complete notification with abort status. */
2596#define CAN_ABORT_STATUS cpu_to_le32(0x1)
2597/* complete notification statuses */
2598#define ABORT_STATUS 0x2
2599
2600/*
2601 * REPLY_SCAN_CMD = 0x80 (response)
2602 */
2603struct iwl_scanreq_notification {
2604 __le32 status; /* 1: okay, 2: cannot fulfill request */
2605} __packed;
2606
2607/*
2608 * SCAN_START_NOTIFICATION = 0x82 (notification only, not a command)
2609 */
2610struct iwl_scanstart_notification {
2611 __le32 tsf_low;
2612 __le32 tsf_high;
2613 __le32 beacon_timer;
2614 u8 channel;
2615 u8 band;
2616 u8 reserved[2];
2617 __le32 status;
2618} __packed;
2619
2620#define SCAN_OWNER_STATUS 0x1
2621#define MEASURE_OWNER_STATUS 0x2
2622
2623#define IWL_PROBE_STATUS_OK 0
2624#define IWL_PROBE_STATUS_TX_FAILED BIT(0)
2625/* error statuses combined with TX_FAILED */
2626#define IWL_PROBE_STATUS_FAIL_TTL BIT(1)
2627#define IWL_PROBE_STATUS_FAIL_BT BIT(2)
2628
2629#define NUMBER_OF_STATISTICS 1 /* first __le32 is good CRC */
2630/*
2631 * SCAN_RESULTS_NOTIFICATION = 0x83 (notification only, not a command)
2632 */
2633struct iwl_scanresults_notification {
2634 u8 channel;
2635 u8 band;
2636 u8 probe_status;
2637 u8 num_probe_not_sent; /* not enough time to send */
2638 __le32 tsf_low;
2639 __le32 tsf_high;
2640 __le32 statistics[NUMBER_OF_STATISTICS];
2641} __packed;
2642
2643/*
2644 * SCAN_COMPLETE_NOTIFICATION = 0x84 (notification only, not a command)
2645 */
2646struct iwl_scancomplete_notification {
2647 u8 scanned_channels;
2648 u8 status;
2649 u8 last_channel;
2650 __le32 tsf_low;
2651 __le32 tsf_high;
2652} __packed;
2653
2654
2655/******************************************************************************
2656 * (9)
2657 * IBSS/AP Commands and Notifications:
2658 *
2659 *****************************************************************************/
2660
2661enum iwl_ibss_manager {
2662 IWL_NOT_IBSS_MANAGER = 0,
2663 IWL_IBSS_MANAGER = 1,
2664};
2665
2666/*
2667 * BEACON_NOTIFICATION = 0x90 (notification only, not a command)
2668 */
2669
2670struct iwl3945_beacon_notif {
2671 struct iwl3945_tx_resp beacon_notify_hdr;
2672 __le32 low_tsf;
2673 __le32 high_tsf;
2674 __le32 ibss_mgr_status;
2675} __packed;
2676
2677struct iwl4965_beacon_notif {
2678 struct iwl4965_tx_resp beacon_notify_hdr;
2679 __le32 low_tsf;
2680 __le32 high_tsf;
2681 __le32 ibss_mgr_status;
2682} __packed;
2683
2684/*
2685 * REPLY_TX_BEACON = 0x91 (command, has simple generic response)
2686 */
2687
2688struct iwl3945_tx_beacon_cmd {
2689 struct iwl3945_tx_cmd tx;
2690 __le16 tim_idx;
2691 u8 tim_size;
2692 u8 reserved1;
2693 struct ieee80211_hdr frame[0]; /* beacon frame */
2694} __packed;
2695
2696struct iwl_tx_beacon_cmd {
2697 struct iwl_tx_cmd tx;
2698 __le16 tim_idx;
2699 u8 tim_size;
2700 u8 reserved1;
2701 struct ieee80211_hdr frame[0]; /* beacon frame */
2702} __packed;
2703
2704/******************************************************************************
2705 * (10)
2706 * Statistics Commands and Notifications:
2707 *
2708 *****************************************************************************/
2709
2710#define IWL_TEMP_CONVERT 260
2711
2712#define SUP_RATE_11A_MAX_NUM_CHANNELS 8
2713#define SUP_RATE_11B_MAX_NUM_CHANNELS 4
2714#define SUP_RATE_11G_MAX_NUM_CHANNELS 12
2715
2716/* Used for passing to driver number of successes and failures per rate */
2717struct rate_histogram {
2718 union {
2719 __le32 a[SUP_RATE_11A_MAX_NUM_CHANNELS];
2720 __le32 b[SUP_RATE_11B_MAX_NUM_CHANNELS];
2721 __le32 g[SUP_RATE_11G_MAX_NUM_CHANNELS];
2722 } success;
2723 union {
2724 __le32 a[SUP_RATE_11A_MAX_NUM_CHANNELS];
2725 __le32 b[SUP_RATE_11B_MAX_NUM_CHANNELS];
2726 __le32 g[SUP_RATE_11G_MAX_NUM_CHANNELS];
2727 } failed;
2728} __packed;
2729
2730/* statistics command response */
2731
2732struct iwl39_statistics_rx_phy {
2733 __le32 ina_cnt;
2734 __le32 fina_cnt;
2735 __le32 plcp_err;
2736 __le32 crc32_err;
2737 __le32 overrun_err;
2738 __le32 early_overrun_err;
2739 __le32 crc32_good;
2740 __le32 false_alarm_cnt;
2741 __le32 fina_sync_err_cnt;
2742 __le32 sfd_timeout;
2743 __le32 fina_timeout;
2744 __le32 unresponded_rts;
2745 __le32 rxe_frame_limit_overrun;
2746 __le32 sent_ack_cnt;
2747 __le32 sent_cts_cnt;
2748} __packed;
2749
2750struct iwl39_statistics_rx_non_phy {
2751 __le32 bogus_cts; /* CTS received when not expecting CTS */
2752 __le32 bogus_ack; /* ACK received when not expecting ACK */
2753 __le32 non_bssid_frames; /* number of frames with BSSID that
2754 * doesn't belong to the STA BSSID */
2755 __le32 filtered_frames; /* count frames that were dumped in the
2756 * filtering process */
2757 __le32 non_channel_beacons; /* beacons with our bss id but not on
2758 * our serving channel */
2759} __packed;
2760
2761struct iwl39_statistics_rx {
2762 struct iwl39_statistics_rx_phy ofdm;
2763 struct iwl39_statistics_rx_phy cck;
2764 struct iwl39_statistics_rx_non_phy general;
2765} __packed;
2766
2767struct iwl39_statistics_tx {
2768 __le32 preamble_cnt;
2769 __le32 rx_detected_cnt;
2770 __le32 bt_prio_defer_cnt;
2771 __le32 bt_prio_kill_cnt;
2772 __le32 few_bytes_cnt;
2773 __le32 cts_timeout;
2774 __le32 ack_timeout;
2775 __le32 expected_ack_cnt;
2776 __le32 actual_ack_cnt;
2777} __packed;
2778
2779struct statistics_dbg {
2780 __le32 burst_check;
2781 __le32 burst_count;
2782 __le32 wait_for_silence_timeout_cnt;
2783 __le32 reserved[3];
2784} __packed;
2785
2786struct iwl39_statistics_div {
2787 __le32 tx_on_a;
2788 __le32 tx_on_b;
2789 __le32 exec_time;
2790 __le32 probe_time;
2791} __packed;
2792
2793struct iwl39_statistics_general {
2794 __le32 temperature;
2795 struct statistics_dbg dbg;
2796 __le32 sleep_time;
2797 __le32 slots_out;
2798 __le32 slots_idle;
2799 __le32 ttl_timestamp;
2800 struct iwl39_statistics_div div;
2801} __packed;
2802
2803struct statistics_rx_phy {
2804 __le32 ina_cnt;
2805 __le32 fina_cnt;
2806 __le32 plcp_err;
2807 __le32 crc32_err;
2808 __le32 overrun_err;
2809 __le32 early_overrun_err;
2810 __le32 crc32_good;
2811 __le32 false_alarm_cnt;
2812 __le32 fina_sync_err_cnt;
2813 __le32 sfd_timeout;
2814 __le32 fina_timeout;
2815 __le32 unresponded_rts;
2816 __le32 rxe_frame_limit_overrun;
2817 __le32 sent_ack_cnt;
2818 __le32 sent_cts_cnt;
2819 __le32 sent_ba_rsp_cnt;
2820 __le32 dsp_self_kill;
2821 __le32 mh_format_err;
2822 __le32 re_acq_main_rssi_sum;
2823 __le32 reserved3;
2824} __packed;
2825
2826struct statistics_rx_ht_phy {
2827 __le32 plcp_err;
2828 __le32 overrun_err;
2829 __le32 early_overrun_err;
2830 __le32 crc32_good;
2831 __le32 crc32_err;
2832 __le32 mh_format_err;
2833 __le32 agg_crc32_good;
2834 __le32 agg_mpdu_cnt;
2835 __le32 agg_cnt;
2836 __le32 unsupport_mcs;
2837} __packed;
2838
2839#define INTERFERENCE_DATA_AVAILABLE cpu_to_le32(1)
2840
2841struct statistics_rx_non_phy {
2842 __le32 bogus_cts; /* CTS received when not expecting CTS */
2843 __le32 bogus_ack; /* ACK received when not expecting ACK */
2844 __le32 non_bssid_frames; /* number of frames with BSSID that
2845 * doesn't belong to the STA BSSID */
2846 __le32 filtered_frames; /* count frames that were dumped in the
2847 * filtering process */
2848 __le32 non_channel_beacons; /* beacons with our bss id but not on
2849 * our serving channel */
2850 __le32 channel_beacons; /* beacons with our bss id and in our
2851 * serving channel */
2852 __le32 num_missed_bcon; /* number of missed beacons */
2853 __le32 adc_rx_saturation_time; /* count in 0.8us units the time the
2854 * ADC was in saturation */
2855 __le32 ina_detection_search_time;/* total time (in 0.8us) searched
2856 * for INA */
2857 __le32 beacon_silence_rssi_a; /* RSSI silence after beacon frame */
2858 __le32 beacon_silence_rssi_b; /* RSSI silence after beacon frame */
2859 __le32 beacon_silence_rssi_c; /* RSSI silence after beacon frame */
2860 __le32 interference_data_flag; /* flag for interference data
2861 * availability. 1 when data is
2862 * available. */
2863 __le32 channel_load; /* counts RX Enable time in uSec */
2864 __le32 dsp_false_alarms; /* DSP false alarm (both OFDM
2865 * and CCK) counter */
2866 __le32 beacon_rssi_a;
2867 __le32 beacon_rssi_b;
2868 __le32 beacon_rssi_c;
2869 __le32 beacon_energy_a;
2870 __le32 beacon_energy_b;
2871 __le32 beacon_energy_c;
2872} __packed;
2873
2874struct statistics_rx {
2875 struct statistics_rx_phy ofdm;
2876 struct statistics_rx_phy cck;
2877 struct statistics_rx_non_phy general;
2878 struct statistics_rx_ht_phy ofdm_ht;
2879} __packed;
2880
2881/**
2882 * struct statistics_tx_power - current tx power
2883 *
2884 * @ant_a: current tx power on chain a in 1/2 dB step
2885 * @ant_b: current tx power on chain b in 1/2 dB step
2886 * @ant_c: current tx power on chain c in 1/2 dB step
2887 */
2888struct statistics_tx_power {
2889 u8 ant_a;
2890 u8 ant_b;
2891 u8 ant_c;
2892 u8 reserved;
2893} __packed;
2894
2895struct statistics_tx_non_phy_agg {
2896 __le32 ba_timeout;
2897 __le32 ba_reschedule_frames;
2898 __le32 scd_query_agg_frame_cnt;
2899 __le32 scd_query_no_agg;
2900 __le32 scd_query_agg;
2901 __le32 scd_query_mismatch;
2902 __le32 frame_not_ready;
2903 __le32 underrun;
2904 __le32 bt_prio_kill;
2905 __le32 rx_ba_rsp_cnt;
2906} __packed;
2907
2908struct statistics_tx {
2909 __le32 preamble_cnt;
2910 __le32 rx_detected_cnt;
2911 __le32 bt_prio_defer_cnt;
2912 __le32 bt_prio_kill_cnt;
2913 __le32 few_bytes_cnt;
2914 __le32 cts_timeout;
2915 __le32 ack_timeout;
2916 __le32 expected_ack_cnt;
2917 __le32 actual_ack_cnt;
2918 __le32 dump_msdu_cnt;
2919 __le32 burst_abort_next_frame_mismatch_cnt;
2920 __le32 burst_abort_missing_next_frame_cnt;
2921 __le32 cts_timeout_collision;
2922 __le32 ack_or_ba_timeout_collision;
2923 struct statistics_tx_non_phy_agg agg;
2924
2925 __le32 reserved1;
2926} __packed;
2927
2928
2929struct statistics_div {
2930 __le32 tx_on_a;
2931 __le32 tx_on_b;
2932 __le32 exec_time;
2933 __le32 probe_time;
2934 __le32 reserved1;
2935 __le32 reserved2;
2936} __packed;
2937
2938struct statistics_general_common {
2939 __le32 temperature; /* radio temperature */
2940 struct statistics_dbg dbg;
2941 __le32 sleep_time;
2942 __le32 slots_out;
2943 __le32 slots_idle;
2944 __le32 ttl_timestamp;
2945 struct statistics_div div;
2946 __le32 rx_enable_counter;
2947 /*
2948 * num_of_sos_states:
2949 * count the number of times we have to re-tune
2950 * in order to get out of bad PHY status
2951 */
2952 __le32 num_of_sos_states;
2953} __packed;
2954
2955struct statistics_general {
2956 struct statistics_general_common common;
2957 __le32 reserved2;
2958 __le32 reserved3;
2959} __packed;
2960
2961#define UCODE_STATISTICS_CLEAR_MSK (0x1 << 0)
2962#define UCODE_STATISTICS_FREQUENCY_MSK (0x1 << 1)
2963#define UCODE_STATISTICS_NARROW_BAND_MSK (0x1 << 2)
2964
2965/*
2966 * REPLY_STATISTICS_CMD = 0x9c,
2967 * all devices identical.
2968 *
2969 * This command triggers an immediate response containing uCode statistics.
2970 * The response is in the same format as STATISTICS_NOTIFICATION 0x9d, below.
2971 *
2972 * If the CLEAR_STATS configuration flag is set, uCode will clear its
2973 * internal copy of the statistics (counters) after issuing the response.
2974 * This flag does not affect STATISTICS_NOTIFICATIONs after beacons (see below).
2975 *
2976 * If the DISABLE_NOTIF configuration flag is set, uCode will not issue
2977 * STATISTICS_NOTIFICATIONs after received beacons (see below). This flag
2978 * does not affect the response to the REPLY_STATISTICS_CMD 0x9c itself.
2979 */
2980#define IWL_STATS_CONF_CLEAR_STATS cpu_to_le32(0x1) /* see above */
2981#define IWL_STATS_CONF_DISABLE_NOTIF cpu_to_le32(0x2)/* see above */
2982struct iwl_statistics_cmd {
2983 __le32 configuration_flags; /* IWL_STATS_CONF_* */
2984} __packed;
2985
2986/*
2987 * STATISTICS_NOTIFICATION = 0x9d (notification only, not a command)
2988 *
2989 * By default, uCode issues this notification after receiving a beacon
2990 * while associated. To disable this behavior, set DISABLE_NOTIF flag in the
2991 * REPLY_STATISTICS_CMD 0x9c, above.
2992 *
2993 * Statistics counters continue to increment beacon after beacon, but are
2994 * cleared when changing channels or when driver issues REPLY_STATISTICS_CMD
2995 * 0x9c with CLEAR_STATS bit set (see above).
2996 *
2997 * uCode also issues this notification during scans. uCode clears statistics
2998 * appropriately so that each notification contains statistics for only the
2999 * one channel that has just been scanned.
3000 */
3001#define STATISTICS_REPLY_FLG_BAND_24G_MSK cpu_to_le32(0x2)
3002#define STATISTICS_REPLY_FLG_HT40_MODE_MSK cpu_to_le32(0x8)
3003
3004struct iwl3945_notif_statistics {
3005 __le32 flag;
3006 struct iwl39_statistics_rx rx;
3007 struct iwl39_statistics_tx tx;
3008 struct iwl39_statistics_general general;
3009} __packed;
3010
3011struct iwl_notif_statistics {
3012 __le32 flag;
3013 struct statistics_rx rx;
3014 struct statistics_tx tx;
3015 struct statistics_general general;
3016} __packed;
3017
3018/*
3019 * MISSED_BEACONS_NOTIFICATION = 0xa2 (notification only, not a command)
3020 *
3021 * uCode send MISSED_BEACONS_NOTIFICATION to driver when detect beacon missed
3022 * in regardless of how many missed beacons, which mean when driver receive the
3023 * notification, inside the command, it can find all the beacons information
3024 * which include number of total missed beacons, number of consecutive missed
3025 * beacons, number of beacons received and number of beacons expected to
3026 * receive.
3027 *
3028 * If uCode detected consecutive_missed_beacons > 5, it will reset the radio
3029 * in order to bring the radio/PHY back to working state; which has no relation
3030 * to when driver will perform sensitivity calibration.
3031 *
3032 * Driver should set it own missed_beacon_threshold to decide when to perform
3033 * sensitivity calibration based on number of consecutive missed beacons in
3034 * order to improve overall performance, especially in noisy environment.
3035 *
3036 */
3037
3038#define IWL_MISSED_BEACON_THRESHOLD_MIN (1)
3039#define IWL_MISSED_BEACON_THRESHOLD_DEF (5)
3040#define IWL_MISSED_BEACON_THRESHOLD_MAX IWL_MISSED_BEACON_THRESHOLD_DEF
3041
3042struct iwl_missed_beacon_notif {
3043 __le32 consecutive_missed_beacons;
3044 __le32 total_missed_becons;
3045 __le32 num_expected_beacons;
3046 __le32 num_recvd_beacons;
3047} __packed;
3048
3049
3050/******************************************************************************
3051 * (11)
3052 * Rx Calibration Commands:
3053 *
3054 * With the uCode used for open source drivers, most Tx calibration (except
3055 * for Tx Power) and most Rx calibration is done by uCode during the
3056 * "initialize" phase of uCode boot. Driver must calibrate only:
3057 *
3058 * 1) Tx power (depends on temperature), described elsewhere
3059 * 2) Receiver gain balance (optimize MIMO, and detect disconnected antennas)
3060 * 3) Receiver sensitivity (to optimize signal detection)
3061 *
3062 *****************************************************************************/
3063
3064/**
3065 * SENSITIVITY_CMD = 0xa8 (command, has simple generic response)
3066 *
3067 * This command sets up the Rx signal detector for a sensitivity level that
3068 * is high enough to lock onto all signals within the associated network,
3069 * but low enough to ignore signals that are below a certain threshold, so as
3070 * not to have too many "false alarms". False alarms are signals that the
3071 * Rx DSP tries to lock onto, but then discards after determining that they
3072 * are noise.
3073 *
3074 * The optimum number of false alarms is between 5 and 50 per 200 TUs
3075 * (200 * 1024 uSecs, i.e. 204.8 milliseconds) of actual Rx time (i.e.
3076 * time listening, not transmitting). Driver must adjust sensitivity so that
3077 * the ratio of actual false alarms to actual Rx time falls within this range.
3078 *
3079 * While associated, uCode delivers STATISTICS_NOTIFICATIONs after each
3080 * received beacon. These provide information to the driver to analyze the
3081 * sensitivity. Don't analyze statistics that come in from scanning, or any
3082 * other non-associated-network source. Pertinent statistics include:
3083 *
3084 * From "general" statistics (struct statistics_rx_non_phy):
3085 *
3086 * (beacon_energy_[abc] & 0x0FF00) >> 8 (unsigned, higher value is lower level)
3087 * Measure of energy of desired signal. Used for establishing a level
3088 * below which the device does not detect signals.
3089 *
3090 * (beacon_silence_rssi_[abc] & 0x0FF00) >> 8 (unsigned, units in dB)
3091 * Measure of background noise in silent period after beacon.
3092 *
3093 * channel_load
3094 * uSecs of actual Rx time during beacon period (varies according to
3095 * how much time was spent transmitting).
3096 *
3097 * From "cck" and "ofdm" statistics (struct statistics_rx_phy), separately:
3098 *
3099 * false_alarm_cnt
3100 * Signal locks abandoned early (before phy-level header).
3101 *
3102 * plcp_err
3103 * Signal locks abandoned late (during phy-level header).
3104 *
3105 * NOTE: Both false_alarm_cnt and plcp_err increment monotonically from
3106 * beacon to beacon, i.e. each value is an accumulation of all errors
3107 * before and including the latest beacon. Values will wrap around to 0
3108 * after counting up to 2^32 - 1. Driver must differentiate vs.
3109 * previous beacon's values to determine # false alarms in the current
3110 * beacon period.
3111 *
3112 * Total number of false alarms = false_alarms + plcp_errs
3113 *
3114 * For OFDM, adjust the following table entries in struct iwl_sensitivity_cmd
3115 * (notice that the start points for OFDM are at or close to settings for
3116 * maximum sensitivity):
3117 *
3118 * START / MIN / MAX
3119 * HD_AUTO_CORR32_X1_TH_ADD_MIN_INDEX 90 / 85 / 120
3120 * HD_AUTO_CORR32_X1_TH_ADD_MIN_MRC_INDEX 170 / 170 / 210
3121 * HD_AUTO_CORR32_X4_TH_ADD_MIN_INDEX 105 / 105 / 140
3122 * HD_AUTO_CORR32_X4_TH_ADD_MIN_MRC_INDEX 220 / 220 / 270
3123 *
3124 * If actual rate of OFDM false alarms (+ plcp_errors) is too high
3125 * (greater than 50 for each 204.8 msecs listening), reduce sensitivity
3126 * by *adding* 1 to all 4 of the table entries above, up to the max for
3127 * each entry. Conversely, if false alarm rate is too low (less than 5
3128 * for each 204.8 msecs listening), *subtract* 1 from each entry to
3129 * increase sensitivity.
3130 *
3131 * For CCK sensitivity, keep track of the following:
3132 *
3133 * 1). 20-beacon history of maximum background noise, indicated by
3134 * (beacon_silence_rssi_[abc] & 0x0FF00), units in dB, across the
3135 * 3 receivers. For any given beacon, the "silence reference" is
3136 * the maximum of last 60 samples (20 beacons * 3 receivers).
3137 *
3138 * 2). 10-beacon history of strongest signal level, as indicated
3139 * by (beacon_energy_[abc] & 0x0FF00) >> 8, across the 3 receivers,
3140 * i.e. the strength of the signal through the best receiver at the
3141 * moment. These measurements are "upside down", with lower values
3142 * for stronger signals, so max energy will be *minimum* value.
3143 *
3144 * Then for any given beacon, the driver must determine the *weakest*
3145 * of the strongest signals; this is the minimum level that needs to be
3146 * successfully detected, when using the best receiver at the moment.
3147 * "Max cck energy" is the maximum (higher value means lower energy!)
3148 * of the last 10 minima. Once this is determined, driver must add
3149 * a little margin by adding "6" to it.
3150 *
3151 * 3). Number of consecutive beacon periods with too few false alarms.
3152 * Reset this to 0 at the first beacon period that falls within the
3153 * "good" range (5 to 50 false alarms per 204.8 milliseconds rx).
3154 *
3155 * Then, adjust the following CCK table entries in struct iwl_sensitivity_cmd
3156 * (notice that the start points for CCK are at maximum sensitivity):
3157 *
3158 * START / MIN / MAX
3159 * HD_AUTO_CORR40_X4_TH_ADD_MIN_INDEX 125 / 125 / 200
3160 * HD_AUTO_CORR40_X4_TH_ADD_MIN_MRC_INDEX 200 / 200 / 400
3161 * HD_MIN_ENERGY_CCK_DET_INDEX 100 / 0 / 100
3162 *
3163 * If actual rate of CCK false alarms (+ plcp_errors) is too high
3164 * (greater than 50 for each 204.8 msecs listening), method for reducing
3165 * sensitivity is:
3166 *
3167 * 1) *Add* 3 to value in HD_AUTO_CORR40_X4_TH_ADD_MIN_MRC_INDEX,
3168 * up to max 400.
3169 *
3170 * 2) If current value in HD_AUTO_CORR40_X4_TH_ADD_MIN_INDEX is < 160,
3171 * sensitivity has been reduced a significant amount; bring it up to
3172 * a moderate 161. Otherwise, *add* 3, up to max 200.
3173 *
3174 * 3) a) If current value in HD_AUTO_CORR40_X4_TH_ADD_MIN_INDEX is > 160,
3175 * sensitivity has been reduced only a moderate or small amount;
3176 * *subtract* 2 from value in HD_MIN_ENERGY_CCK_DET_INDEX,
3177 * down to min 0. Otherwise (if gain has been significantly reduced),
3178 * don't change the HD_MIN_ENERGY_CCK_DET_INDEX value.
3179 *
3180 * b) Save a snapshot of the "silence reference".
3181 *
3182 * If actual rate of CCK false alarms (+ plcp_errors) is too low
3183 * (less than 5 for each 204.8 msecs listening), method for increasing
3184 * sensitivity is used only if:
3185 *
3186 * 1a) Previous beacon did not have too many false alarms
3187 * 1b) AND difference between previous "silence reference" and current
3188 * "silence reference" (prev - current) is 2 or more,
3189 * OR 2) 100 or more consecutive beacon periods have had rate of
3190 * less than 5 false alarms per 204.8 milliseconds rx time.
3191 *
3192 * Method for increasing sensitivity:
3193 *
3194 * 1) *Subtract* 3 from value in HD_AUTO_CORR40_X4_TH_ADD_MIN_INDEX,
3195 * down to min 125.
3196 *
3197 * 2) *Subtract* 3 from value in HD_AUTO_CORR40_X4_TH_ADD_MIN_MRC_INDEX,
3198 * down to min 200.
3199 *
3200 * 3) *Add* 2 to value in HD_MIN_ENERGY_CCK_DET_INDEX, up to max 100.
3201 *
3202 * If actual rate of CCK false alarms (+ plcp_errors) is within good range
3203 * (between 5 and 50 for each 204.8 msecs listening):
3204 *
3205 * 1) Save a snapshot of the silence reference.
3206 *
3207 * 2) If previous beacon had too many CCK false alarms (+ plcp_errors),
3208 * give some extra margin to energy threshold by *subtracting* 8
3209 * from value in HD_MIN_ENERGY_CCK_DET_INDEX.
3210 *
3211 * For all cases (too few, too many, good range), make sure that the CCK
3212 * detection threshold (energy) is below the energy level for robust
3213 * detection over the past 10 beacon periods, the "Max cck energy".
3214 * Lower values mean higher energy; this means making sure that the value
3215 * in HD_MIN_ENERGY_CCK_DET_INDEX is at or *above* "Max cck energy".
3216 *
3217 */
3218
3219/*
3220 * Table entries in SENSITIVITY_CMD (struct iwl_sensitivity_cmd)
3221 */
3222#define HD_TABLE_SIZE (11) /* number of entries */
3223#define HD_MIN_ENERGY_CCK_DET_INDEX (0) /* table indexes */
3224#define HD_MIN_ENERGY_OFDM_DET_INDEX (1)
3225#define HD_AUTO_CORR32_X1_TH_ADD_MIN_INDEX (2)
3226#define HD_AUTO_CORR32_X1_TH_ADD_MIN_MRC_INDEX (3)
3227#define HD_AUTO_CORR40_X4_TH_ADD_MIN_MRC_INDEX (4)
3228#define HD_AUTO_CORR32_X4_TH_ADD_MIN_INDEX (5)
3229#define HD_AUTO_CORR32_X4_TH_ADD_MIN_MRC_INDEX (6)
3230#define HD_BARKER_CORR_TH_ADD_MIN_INDEX (7)
3231#define HD_BARKER_CORR_TH_ADD_MIN_MRC_INDEX (8)
3232#define HD_AUTO_CORR40_X4_TH_ADD_MIN_INDEX (9)
3233#define HD_OFDM_ENERGY_TH_IN_INDEX (10)
3234
3235/* Control field in struct iwl_sensitivity_cmd */
3236#define SENSITIVITY_CMD_CONTROL_DEFAULT_TABLE cpu_to_le16(0)
3237#define SENSITIVITY_CMD_CONTROL_WORK_TABLE cpu_to_le16(1)
3238
3239/**
3240 * struct iwl_sensitivity_cmd
3241 * @control: (1) updates working table, (0) updates default table
3242 * @table: energy threshold values, use HD_* as index into table
3243 *
3244 * Always use "1" in "control" to update uCode's working table and DSP.
3245 */
3246struct iwl_sensitivity_cmd {
3247 __le16 control; /* always use "1" */
3248 __le16 table[HD_TABLE_SIZE]; /* use HD_* as index */
3249} __packed;
3250
3251
3252/**
3253 * REPLY_PHY_CALIBRATION_CMD = 0xb0 (command, has simple generic response)
3254 *
3255 * This command sets the relative gains of 4965 device's 3 radio receiver chains.
3256 *
3257 * After the first association, driver should accumulate signal and noise
3258 * statistics from the STATISTICS_NOTIFICATIONs that follow the first 20
3259 * beacons from the associated network (don't collect statistics that come
3260 * in from scanning, or any other non-network source).
3261 *
3262 * DISCONNECTED ANTENNA:
3263 *
3264 * Driver should determine which antennas are actually connected, by comparing
3265 * average beacon signal levels for the 3 Rx chains. Accumulate (add) the
3266 * following values over 20 beacons, one accumulator for each of the chains
3267 * a/b/c, from struct statistics_rx_non_phy:
3268 *
3269 * beacon_rssi_[abc] & 0x0FF (unsigned, units in dB)
3270 *
3271 * Find the strongest signal from among a/b/c. Compare the other two to the
3272 * strongest. If any signal is more than 15 dB (times 20, unless you
3273 * divide the accumulated values by 20) below the strongest, the driver
3274 * considers that antenna to be disconnected, and should not try to use that
3275 * antenna/chain for Rx or Tx. If both A and B seem to be disconnected,
3276 * driver should declare the stronger one as connected, and attempt to use it
3277 * (A and B are the only 2 Tx chains!).
3278 *
3279 *
3280 * RX BALANCE:
3281 *
3282 * Driver should balance the 3 receivers (but just the ones that are connected
3283 * to antennas, see above) for gain, by comparing the average signal levels
3284 * detected during the silence after each beacon (background noise).
3285 * Accumulate (add) the following values over 20 beacons, one accumulator for
3286 * each of the chains a/b/c, from struct statistics_rx_non_phy:
3287 *
3288 * beacon_silence_rssi_[abc] & 0x0FF (unsigned, units in dB)
3289 *
3290 * Find the weakest background noise level from among a/b/c. This Rx chain
3291 * will be the reference, with 0 gain adjustment. Attenuate other channels by
3292 * finding noise difference:
3293 *
3294 * (accum_noise[i] - accum_noise[reference]) / 30
3295 *
3296 * The "30" adjusts the dB in the 20 accumulated samples to units of 1.5 dB.
3297 * For use in diff_gain_[abc] fields of struct iwl_calibration_cmd, the
3298 * driver should limit the difference results to a range of 0-3 (0-4.5 dB),
3299 * and set bit 2 to indicate "reduce gain". The value for the reference
3300 * (weakest) chain should be "0".
3301 *
3302 * diff_gain_[abc] bit fields:
3303 * 2: (1) reduce gain, (0) increase gain
3304 * 1-0: amount of gain, units of 1.5 dB
3305 */
3306
3307/* Phy calibration command for series */
3308/* The default calibrate table size if not specified by firmware */
3309#define IWL_DEFAULT_STANDARD_PHY_CALIBRATE_TBL_SIZE 18
3310enum {
3311 IWL_PHY_CALIBRATE_DIFF_GAIN_CMD = 7,
3312 IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE = 19,
3313};
3314
3315#define IWL_MAX_PHY_CALIBRATE_TBL_SIZE (253)
3316
3317struct iwl_calib_hdr {
3318 u8 op_code;
3319 u8 first_group;
3320 u8 groups_num;
3321 u8 data_valid;
3322} __packed;
3323
3324/* IWL_PHY_CALIBRATE_DIFF_GAIN_CMD (7) */
3325struct iwl_calib_diff_gain_cmd {
3326 struct iwl_calib_hdr hdr;
3327 s8 diff_gain_a; /* see above */
3328 s8 diff_gain_b;
3329 s8 diff_gain_c;
3330 u8 reserved1;
3331} __packed;
3332
3333/******************************************************************************
3334 * (12)
3335 * Miscellaneous Commands:
3336 *
3337 *****************************************************************************/
3338
3339/*
3340 * LEDs Command & Response
3341 * REPLY_LEDS_CMD = 0x48 (command, has simple generic response)
3342 *
3343 * For each of 3 possible LEDs (Activity/Link/Tech, selected by "id" field),
3344 * this command turns it on or off, or sets up a periodic blinking cycle.
3345 */
3346struct iwl_led_cmd {
3347 __le32 interval; /* "interval" in uSec */
3348 u8 id; /* 1: Activity, 2: Link, 3: Tech */
3349 u8 off; /* # intervals off while blinking;
3350 * "0", with >0 "on" value, turns LED on */
3351 u8 on; /* # intervals on while blinking;
3352 * "0", regardless of "off", turns LED off */
3353 u8 reserved;
3354} __packed;
3355
3356
3357/******************************************************************************
3358 * (13)
3359 * Union of all expected notifications/responses:
3360 *
3361 *****************************************************************************/
3362
3363struct iwl_rx_packet {
3364 /*
3365 * The first 4 bytes of the RX frame header contain both the RX frame
3366 * size and some flags.
3367 * Bit fields:
3368 * 31: flag flush RB request
3369 * 30: flag ignore TC (terminal counter) request
3370 * 29: flag fast IRQ request
3371 * 28-14: Reserved
3372 * 13-00: RX frame size
3373 */
3374 __le32 len_n_flags;
3375 struct iwl_cmd_header hdr;
3376 union {
3377 struct iwl3945_rx_frame rx_frame;
3378 struct iwl3945_tx_resp tx_resp;
3379 struct iwl3945_beacon_notif beacon_status;
3380
3381 struct iwl_alive_resp alive_frame;
3382 struct iwl_spectrum_notification spectrum_notif;
3383 struct iwl_csa_notification csa_notif;
3384 struct iwl_error_resp err_resp;
3385 struct iwl_card_state_notif card_state_notif;
3386 struct iwl_add_sta_resp add_sta;
3387 struct iwl_rem_sta_resp rem_sta;
3388 struct iwl_sleep_notification sleep_notif;
3389 struct iwl_spectrum_resp spectrum;
3390 struct iwl_notif_statistics stats;
3391 struct iwl_compressed_ba_resp compressed_ba;
3392 struct iwl_missed_beacon_notif missed_beacon;
3393 __le32 status;
3394 u8 raw[0];
3395 } u;
3396} __packed;
3397
3398#endif /* __iwl_legacy_commands_h__ */