Loading...
Note: File does not exist in v3.1.
1/*
2 * Clause 45 PHY support
3 */
4#include <linux/ethtool.h>
5#include <linux/export.h>
6#include <linux/mdio.h>
7#include <linux/mii.h>
8#include <linux/phy.h>
9
10/**
11 * genphy_c45_setup_forced - configures a forced speed
12 * @phydev: target phy_device struct
13 */
14int genphy_c45_pma_setup_forced(struct phy_device *phydev)
15{
16 int ctrl1, ctrl2, ret;
17
18 /* Half duplex is not supported */
19 if (phydev->duplex != DUPLEX_FULL)
20 return -EINVAL;
21
22 ctrl1 = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_CTRL1);
23 if (ctrl1 < 0)
24 return ctrl1;
25
26 ctrl2 = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_CTRL2);
27 if (ctrl2 < 0)
28 return ctrl2;
29
30 ctrl1 &= ~MDIO_CTRL1_SPEEDSEL;
31 /*
32 * PMA/PMD type selection is 1.7.5:0 not 1.7.3:0. See 45.2.1.6.1
33 * in 802.3-2012 and 802.3-2015.
34 */
35 ctrl2 &= ~(MDIO_PMA_CTRL2_TYPE | 0x30);
36
37 switch (phydev->speed) {
38 case SPEED_10:
39 ctrl2 |= MDIO_PMA_CTRL2_10BT;
40 break;
41 case SPEED_100:
42 ctrl1 |= MDIO_PMA_CTRL1_SPEED100;
43 ctrl2 |= MDIO_PMA_CTRL2_100BTX;
44 break;
45 case SPEED_1000:
46 ctrl1 |= MDIO_PMA_CTRL1_SPEED1000;
47 /* Assume 1000base-T */
48 ctrl2 |= MDIO_PMA_CTRL2_1000BT;
49 break;
50 case SPEED_10000:
51 ctrl1 |= MDIO_CTRL1_SPEED10G;
52 /* Assume 10Gbase-T */
53 ctrl2 |= MDIO_PMA_CTRL2_10GBT;
54 break;
55 default:
56 return -EINVAL;
57 }
58
59 ret = phy_write_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_CTRL1, ctrl1);
60 if (ret < 0)
61 return ret;
62
63 return phy_write_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_CTRL2, ctrl2);
64}
65EXPORT_SYMBOL_GPL(genphy_c45_pma_setup_forced);
66
67/**
68 * genphy_c45_an_disable_aneg - disable auto-negotiation
69 * @phydev: target phy_device struct
70 *
71 * Disable auto-negotiation in the Clause 45 PHY. The link parameters
72 * parameters are controlled through the PMA/PMD MMD registers.
73 *
74 * Returns zero on success, negative errno code on failure.
75 */
76int genphy_c45_an_disable_aneg(struct phy_device *phydev)
77{
78 int val;
79
80 val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_CTRL1);
81 if (val < 0)
82 return val;
83
84 val &= ~(MDIO_AN_CTRL1_ENABLE | MDIO_AN_CTRL1_RESTART);
85
86 return phy_write_mmd(phydev, MDIO_MMD_AN, MDIO_CTRL1, val);
87}
88EXPORT_SYMBOL_GPL(genphy_c45_an_disable_aneg);
89
90/**
91 * genphy_c45_restart_aneg - Enable and restart auto-negotiation
92 * @phydev: target phy_device struct
93 *
94 * This assumes that the auto-negotiation MMD is present.
95 *
96 * Enable and restart auto-negotiation.
97 */
98int genphy_c45_restart_aneg(struct phy_device *phydev)
99{
100 int val;
101
102 val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_CTRL1);
103 if (val < 0)
104 return val;
105
106 val |= MDIO_AN_CTRL1_ENABLE | MDIO_AN_CTRL1_RESTART;
107
108 return phy_write_mmd(phydev, MDIO_MMD_AN, MDIO_CTRL1, val);
109}
110EXPORT_SYMBOL_GPL(genphy_c45_restart_aneg);
111
112/**
113 * genphy_c45_aneg_done - return auto-negotiation complete status
114 * @phydev: target phy_device struct
115 *
116 * This assumes that the auto-negotiation MMD is present.
117 *
118 * Reads the status register from the auto-negotiation MMD, returning:
119 * - positive if auto-negotiation is complete
120 * - negative errno code on error
121 * - zero otherwise
122 */
123int genphy_c45_aneg_done(struct phy_device *phydev)
124{
125 int val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_STAT1);
126
127 return val < 0 ? val : val & MDIO_AN_STAT1_COMPLETE ? 1 : 0;
128}
129EXPORT_SYMBOL_GPL(genphy_c45_aneg_done);
130
131/**
132 * genphy_c45_read_link - read the overall link status from the MMDs
133 * @phydev: target phy_device struct
134 * @mmd_mask: MMDs to read status from
135 *
136 * Read the link status from the specified MMDs, and if they all indicate
137 * that the link is up, return positive. If an error is encountered,
138 * a negative errno will be returned, otherwise zero.
139 */
140int genphy_c45_read_link(struct phy_device *phydev, u32 mmd_mask)
141{
142 int val, devad;
143 bool link = true;
144
145 while (mmd_mask) {
146 devad = __ffs(mmd_mask);
147 mmd_mask &= ~BIT(devad);
148
149 /* The link state is latched low so that momentary link
150 * drops can be detected. Do not double-read the status
151 * register if the link is down.
152 */
153 val = phy_read_mmd(phydev, devad, MDIO_STAT1);
154 if (val < 0)
155 return val;
156
157 if (!(val & MDIO_STAT1_LSTATUS))
158 link = false;
159 }
160
161 return link;
162}
163EXPORT_SYMBOL_GPL(genphy_c45_read_link);
164
165/**
166 * genphy_c45_read_lpa - read the link partner advertisement and pause
167 * @phydev: target phy_device struct
168 *
169 * Read the Clause 45 defined base (7.19) and 10G (7.33) status registers,
170 * filling in the link partner advertisement, pause and asym_pause members
171 * in @phydev. This assumes that the auto-negotiation MMD is present, and
172 * the backplane bit (7.48.0) is clear. Clause 45 PHY drivers are expected
173 * to fill in the remainder of the link partner advert from vendor registers.
174 */
175int genphy_c45_read_lpa(struct phy_device *phydev)
176{
177 int val;
178
179 /* Read the link partner's base page advertisement */
180 val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_LPA);
181 if (val < 0)
182 return val;
183
184 phydev->lp_advertising = mii_lpa_to_ethtool_lpa_t(val);
185 phydev->pause = val & LPA_PAUSE_CAP ? 1 : 0;
186 phydev->asym_pause = val & LPA_PAUSE_ASYM ? 1 : 0;
187
188 /* Read the link partner's 10G advertisement */
189 val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_STAT);
190 if (val < 0)
191 return val;
192
193 if (val & MDIO_AN_10GBT_STAT_LP10G)
194 phydev->lp_advertising |= ADVERTISED_10000baseT_Full;
195
196 return 0;
197}
198EXPORT_SYMBOL_GPL(genphy_c45_read_lpa);
199
200/**
201 * genphy_c45_read_pma - read link speed etc from PMA
202 * @phydev: target phy_device struct
203 */
204int genphy_c45_read_pma(struct phy_device *phydev)
205{
206 int val;
207
208 val = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_CTRL1);
209 if (val < 0)
210 return val;
211
212 switch (val & MDIO_CTRL1_SPEEDSEL) {
213 case 0:
214 phydev->speed = SPEED_10;
215 break;
216 case MDIO_PMA_CTRL1_SPEED100:
217 phydev->speed = SPEED_100;
218 break;
219 case MDIO_PMA_CTRL1_SPEED1000:
220 phydev->speed = SPEED_1000;
221 break;
222 case MDIO_CTRL1_SPEED10G:
223 phydev->speed = SPEED_10000;
224 break;
225 default:
226 phydev->speed = SPEED_UNKNOWN;
227 break;
228 }
229
230 phydev->duplex = DUPLEX_FULL;
231
232 return 0;
233}
234EXPORT_SYMBOL_GPL(genphy_c45_read_pma);
235
236/**
237 * genphy_c45_read_mdix - read mdix status from PMA
238 * @phydev: target phy_device struct
239 */
240int genphy_c45_read_mdix(struct phy_device *phydev)
241{
242 int val;
243
244 if (phydev->speed == SPEED_10000) {
245 val = phy_read_mmd(phydev, MDIO_MMD_PMAPMD,
246 MDIO_PMA_10GBT_SWAPPOL);
247 if (val < 0)
248 return val;
249
250 switch (val) {
251 case MDIO_PMA_10GBT_SWAPPOL_ABNX | MDIO_PMA_10GBT_SWAPPOL_CDNX:
252 phydev->mdix = ETH_TP_MDI;
253 break;
254
255 case 0:
256 phydev->mdix = ETH_TP_MDI_X;
257 break;
258
259 default:
260 phydev->mdix = ETH_TP_MDI_INVALID;
261 break;
262 }
263 }
264
265 return 0;
266}
267EXPORT_SYMBOL_GPL(genphy_c45_read_mdix);
268
269/* The gen10g_* functions are the old Clause 45 stub */
270
271int gen10g_config_aneg(struct phy_device *phydev)
272{
273 return 0;
274}
275EXPORT_SYMBOL_GPL(gen10g_config_aneg);
276
277int gen10g_read_status(struct phy_device *phydev)
278{
279 u32 mmd_mask = phydev->c45_ids.devices_in_package;
280 int ret;
281
282 /* For now just lie and say it's 10G all the time */
283 phydev->speed = SPEED_10000;
284 phydev->duplex = DUPLEX_FULL;
285
286 /* Avoid reading the vendor MMDs */
287 mmd_mask &= ~(BIT(MDIO_MMD_VEND1) | BIT(MDIO_MMD_VEND2));
288
289 ret = genphy_c45_read_link(phydev, mmd_mask);
290
291 phydev->link = ret > 0 ? 1 : 0;
292
293 return 0;
294}
295EXPORT_SYMBOL_GPL(gen10g_read_status);
296
297int gen10g_no_soft_reset(struct phy_device *phydev)
298{
299 /* Do nothing for now */
300 return 0;
301}
302EXPORT_SYMBOL_GPL(gen10g_no_soft_reset);
303
304int gen10g_config_init(struct phy_device *phydev)
305{
306 /* Temporarily just say we support everything */
307 phydev->supported = SUPPORTED_10000baseT_Full;
308 phydev->advertising = SUPPORTED_10000baseT_Full;
309
310 return 0;
311}
312EXPORT_SYMBOL_GPL(gen10g_config_init);
313
314int gen10g_suspend(struct phy_device *phydev)
315{
316 return 0;
317}
318EXPORT_SYMBOL_GPL(gen10g_suspend);
319
320int gen10g_resume(struct phy_device *phydev)
321{
322 return 0;
323}
324EXPORT_SYMBOL_GPL(gen10g_resume);
325
326struct phy_driver genphy_10g_driver = {
327 .phy_id = 0xffffffff,
328 .phy_id_mask = 0xffffffff,
329 .name = "Generic 10G PHY",
330 .soft_reset = gen10g_no_soft_reset,
331 .config_init = gen10g_config_init,
332 .features = 0,
333 .config_aneg = gen10g_config_aneg,
334 .read_status = gen10g_read_status,
335 .suspend = gen10g_suspend,
336 .resume = gen10g_resume,
337};