Loading...
Note: File does not exist in v3.1.
1/*
2 * This header file contains public constants and structures used by
3 * both the SCSI initiator and the SCSI target code.
4 *
5 * For documentation on the OPCODES, MESSAGES, and SENSE values,
6 * please consult the SCSI standard.
7 */
8
9#ifndef _SCSI_PROTO_H_
10#define _SCSI_PROTO_H_
11
12#include <linux/types.h>
13
14/*
15 * SCSI opcodes
16 */
17
18#define TEST_UNIT_READY 0x00
19#define REZERO_UNIT 0x01
20#define REQUEST_SENSE 0x03
21#define FORMAT_UNIT 0x04
22#define READ_BLOCK_LIMITS 0x05
23#define REASSIGN_BLOCKS 0x07
24#define INITIALIZE_ELEMENT_STATUS 0x07
25#define READ_6 0x08
26#define WRITE_6 0x0a
27#define SEEK_6 0x0b
28#define READ_REVERSE 0x0f
29#define WRITE_FILEMARKS 0x10
30#define SPACE 0x11
31#define INQUIRY 0x12
32#define RECOVER_BUFFERED_DATA 0x14
33#define MODE_SELECT 0x15
34#define RESERVE 0x16
35#define RELEASE 0x17
36#define COPY 0x18
37#define ERASE 0x19
38#define MODE_SENSE 0x1a
39#define START_STOP 0x1b
40#define RECEIVE_DIAGNOSTIC 0x1c
41#define SEND_DIAGNOSTIC 0x1d
42#define ALLOW_MEDIUM_REMOVAL 0x1e
43
44#define READ_FORMAT_CAPACITIES 0x23
45#define SET_WINDOW 0x24
46#define READ_CAPACITY 0x25
47#define READ_10 0x28
48#define WRITE_10 0x2a
49#define SEEK_10 0x2b
50#define POSITION_TO_ELEMENT 0x2b
51#define WRITE_VERIFY 0x2e
52#define VERIFY 0x2f
53#define SEARCH_HIGH 0x30
54#define SEARCH_EQUAL 0x31
55#define SEARCH_LOW 0x32
56#define SET_LIMITS 0x33
57#define PRE_FETCH 0x34
58#define READ_POSITION 0x34
59#define SYNCHRONIZE_CACHE 0x35
60#define LOCK_UNLOCK_CACHE 0x36
61#define READ_DEFECT_DATA 0x37
62#define MEDIUM_SCAN 0x38
63#define COMPARE 0x39
64#define COPY_VERIFY 0x3a
65#define WRITE_BUFFER 0x3b
66#define READ_BUFFER 0x3c
67#define UPDATE_BLOCK 0x3d
68#define READ_LONG 0x3e
69#define WRITE_LONG 0x3f
70#define CHANGE_DEFINITION 0x40
71#define WRITE_SAME 0x41
72#define UNMAP 0x42
73#define READ_TOC 0x43
74#define READ_HEADER 0x44
75#define GET_EVENT_STATUS_NOTIFICATION 0x4a
76#define LOG_SELECT 0x4c
77#define LOG_SENSE 0x4d
78#define XDWRITEREAD_10 0x53
79#define MODE_SELECT_10 0x55
80#define RESERVE_10 0x56
81#define RELEASE_10 0x57
82#define MODE_SENSE_10 0x5a
83#define PERSISTENT_RESERVE_IN 0x5e
84#define PERSISTENT_RESERVE_OUT 0x5f
85#define VARIABLE_LENGTH_CMD 0x7f
86#define REPORT_LUNS 0xa0
87#define SECURITY_PROTOCOL_IN 0xa2
88#define MAINTENANCE_IN 0xa3
89#define MAINTENANCE_OUT 0xa4
90#define MOVE_MEDIUM 0xa5
91#define EXCHANGE_MEDIUM 0xa6
92#define READ_12 0xa8
93#define SERVICE_ACTION_OUT_12 0xa9
94#define WRITE_12 0xaa
95#define READ_MEDIA_SERIAL_NUMBER 0xab /* Obsolete with SPC-2 */
96#define SERVICE_ACTION_IN_12 0xab
97#define WRITE_VERIFY_12 0xae
98#define VERIFY_12 0xaf
99#define SEARCH_HIGH_12 0xb0
100#define SEARCH_EQUAL_12 0xb1
101#define SEARCH_LOW_12 0xb2
102#define SECURITY_PROTOCOL_OUT 0xb5
103#define READ_ELEMENT_STATUS 0xb8
104#define SEND_VOLUME_TAG 0xb6
105#define WRITE_LONG_2 0xea
106#define EXTENDED_COPY 0x83
107#define RECEIVE_COPY_RESULTS 0x84
108#define ACCESS_CONTROL_IN 0x86
109#define ACCESS_CONTROL_OUT 0x87
110#define READ_16 0x88
111#define COMPARE_AND_WRITE 0x89
112#define WRITE_16 0x8a
113#define READ_ATTRIBUTE 0x8c
114#define WRITE_ATTRIBUTE 0x8d
115#define VERIFY_16 0x8f
116#define SYNCHRONIZE_CACHE_16 0x91
117#define WRITE_SAME_16 0x93
118#define ZBC_OUT 0x94
119#define ZBC_IN 0x95
120#define SERVICE_ACTION_BIDIRECTIONAL 0x9d
121#define SERVICE_ACTION_IN_16 0x9e
122#define SERVICE_ACTION_OUT_16 0x9f
123/* values for service action in */
124#define SAI_READ_CAPACITY_16 0x10
125#define SAI_GET_LBA_STATUS 0x12
126#define SAI_REPORT_REFERRALS 0x13
127/* values for VARIABLE_LENGTH_CMD service action codes
128 * see spc4r17 Section D.3.5, table D.7 and D.8 */
129#define VLC_SA_RECEIVE_CREDENTIAL 0x1800
130/* values for maintenance in */
131#define MI_REPORT_IDENTIFYING_INFORMATION 0x05
132#define MI_REPORT_TARGET_PGS 0x0a
133#define MI_REPORT_ALIASES 0x0b
134#define MI_REPORT_SUPPORTED_OPERATION_CODES 0x0c
135#define MI_REPORT_SUPPORTED_TASK_MANAGEMENT_FUNCTIONS 0x0d
136#define MI_REPORT_PRIORITY 0x0e
137#define MI_REPORT_TIMESTAMP 0x0f
138#define MI_MANAGEMENT_PROTOCOL_IN 0x10
139/* value for MI_REPORT_TARGET_PGS ext header */
140#define MI_EXT_HDR_PARAM_FMT 0x20
141/* values for maintenance out */
142#define MO_SET_IDENTIFYING_INFORMATION 0x06
143#define MO_SET_TARGET_PGS 0x0a
144#define MO_CHANGE_ALIASES 0x0b
145#define MO_SET_PRIORITY 0x0e
146#define MO_SET_TIMESTAMP 0x0f
147#define MO_MANAGEMENT_PROTOCOL_OUT 0x10
148/* values for ZBC_IN */
149#define ZI_REPORT_ZONES 0x00
150/* values for ZBC_OUT */
151#define ZO_CLOSE_ZONE 0x01
152#define ZO_FINISH_ZONE 0x02
153#define ZO_OPEN_ZONE 0x03
154#define ZO_RESET_WRITE_POINTER 0x04
155/* values for variable length command */
156#define XDREAD_32 0x03
157#define XDWRITE_32 0x04
158#define XPWRITE_32 0x06
159#define XDWRITEREAD_32 0x07
160#define READ_32 0x09
161#define VERIFY_32 0x0a
162#define WRITE_32 0x0b
163#define WRITE_SAME_32 0x0d
164
165/* Values for T10/04-262r7 */
166#define ATA_16 0x85 /* 16-byte pass-thru */
167#define ATA_12 0xa1 /* 12-byte pass-thru */
168
169/* Vendor specific CDBs start here */
170#define VENDOR_SPECIFIC_CDB 0xc0
171
172/*
173 * SCSI command lengths
174 */
175
176#define SCSI_MAX_VARLEN_CDB_SIZE 260
177
178/* defined in T10 SCSI Primary Commands-2 (SPC2) */
179struct scsi_varlen_cdb_hdr {
180 __u8 opcode; /* opcode always == VARIABLE_LENGTH_CMD */
181 __u8 control;
182 __u8 misc[5];
183 __u8 additional_cdb_length; /* total cdb length - 8 */
184 __be16 service_action;
185 /* service specific data follows */
186};
187
188/*
189 * SCSI Architecture Model (SAM) Status codes. Taken from SAM-3 draft
190 * T10/1561-D Revision 4 Draft dated 7th November 2002.
191 */
192#define SAM_STAT_GOOD 0x00
193#define SAM_STAT_CHECK_CONDITION 0x02
194#define SAM_STAT_CONDITION_MET 0x04
195#define SAM_STAT_BUSY 0x08
196#define SAM_STAT_INTERMEDIATE 0x10
197#define SAM_STAT_INTERMEDIATE_CONDITION_MET 0x14
198#define SAM_STAT_RESERVATION_CONFLICT 0x18
199#define SAM_STAT_COMMAND_TERMINATED 0x22 /* obsolete in SAM-3 */
200#define SAM_STAT_TASK_SET_FULL 0x28
201#define SAM_STAT_ACA_ACTIVE 0x30
202#define SAM_STAT_TASK_ABORTED 0x40
203
204/*
205 * Status codes. These are deprecated as they are shifted 1 bit right
206 * from those found in the SCSI standards. This causes confusion for
207 * applications that are ported to several OSes. Prefer SAM Status codes
208 * above.
209 */
210
211#define GOOD 0x00
212#define CHECK_CONDITION 0x01
213#define CONDITION_GOOD 0x02
214#define BUSY 0x04
215#define INTERMEDIATE_GOOD 0x08
216#define INTERMEDIATE_C_GOOD 0x0a
217#define RESERVATION_CONFLICT 0x0c
218#define COMMAND_TERMINATED 0x11
219#define QUEUE_FULL 0x14
220#define ACA_ACTIVE 0x18
221#define TASK_ABORTED 0x20
222
223#define STATUS_MASK 0xfe
224
225/*
226 * SENSE KEYS
227 */
228
229#define NO_SENSE 0x00
230#define RECOVERED_ERROR 0x01
231#define NOT_READY 0x02
232#define MEDIUM_ERROR 0x03
233#define HARDWARE_ERROR 0x04
234#define ILLEGAL_REQUEST 0x05
235#define UNIT_ATTENTION 0x06
236#define DATA_PROTECT 0x07
237#define BLANK_CHECK 0x08
238#define COPY_ABORTED 0x0a
239#define ABORTED_COMMAND 0x0b
240#define VOLUME_OVERFLOW 0x0d
241#define MISCOMPARE 0x0e
242
243
244/*
245 * DEVICE TYPES
246 * Please keep them in 0x%02x format for $MODALIAS to work
247 */
248
249#define TYPE_DISK 0x00
250#define TYPE_TAPE 0x01
251#define TYPE_PRINTER 0x02
252#define TYPE_PROCESSOR 0x03 /* HP scanners use this */
253#define TYPE_WORM 0x04 /* Treated as ROM by our system */
254#define TYPE_ROM 0x05
255#define TYPE_SCANNER 0x06
256#define TYPE_MOD 0x07 /* Magneto-optical disk -
257 * - treated as TYPE_DISK */
258#define TYPE_MEDIUM_CHANGER 0x08
259#define TYPE_COMM 0x09 /* Communications device */
260#define TYPE_RAID 0x0c
261#define TYPE_ENCLOSURE 0x0d /* Enclosure Services Device */
262#define TYPE_RBC 0x0e
263#define TYPE_OSD 0x11
264#define TYPE_ZBC 0x14
265#define TYPE_WLUN 0x1e /* well-known logical unit */
266#define TYPE_NO_LUN 0x7f
267
268/* SCSI protocols; these are taken from SPC-3 section 7.5 */
269enum scsi_protocol {
270 SCSI_PROTOCOL_FCP = 0, /* Fibre Channel */
271 SCSI_PROTOCOL_SPI = 1, /* parallel SCSI */
272 SCSI_PROTOCOL_SSA = 2, /* Serial Storage Architecture - Obsolete */
273 SCSI_PROTOCOL_SBP = 3, /* firewire */
274 SCSI_PROTOCOL_SRP = 4, /* Infiniband RDMA */
275 SCSI_PROTOCOL_ISCSI = 5,
276 SCSI_PROTOCOL_SAS = 6,
277 SCSI_PROTOCOL_ADT = 7, /* Media Changers */
278 SCSI_PROTOCOL_ATA = 8,
279 SCSI_PROTOCOL_UNSPEC = 0xf, /* No specific protocol */
280};
281
282/*
283 * ScsiLun: 8 byte LUN.
284 */
285struct scsi_lun {
286 __u8 scsi_lun[8];
287};
288
289/* SPC asymmetric access states */
290#define SCSI_ACCESS_STATE_OPTIMAL 0x00
291#define SCSI_ACCESS_STATE_ACTIVE 0x01
292#define SCSI_ACCESS_STATE_STANDBY 0x02
293#define SCSI_ACCESS_STATE_UNAVAILABLE 0x03
294#define SCSI_ACCESS_STATE_LBA 0x04
295#define SCSI_ACCESS_STATE_OFFLINE 0x0e
296#define SCSI_ACCESS_STATE_TRANSITIONING 0x0f
297
298/* Values for REPORT TARGET GROUP STATES */
299#define SCSI_ACCESS_STATE_MASK 0x0f
300#define SCSI_ACCESS_STATE_PREFERRED 0x80
301
302/* Reporting options for REPORT ZONES */
303enum zbc_zone_reporting_options {
304 ZBC_ZONE_REPORTING_OPTION_ALL = 0,
305 ZBC_ZONE_REPORTING_OPTION_EMPTY,
306 ZBC_ZONE_REPORTING_OPTION_IMPLICIT_OPEN,
307 ZBC_ZONE_REPORTING_OPTION_EXPLICIT_OPEN,
308 ZBC_ZONE_REPORTING_OPTION_CLOSED,
309 ZBC_ZONE_REPORTING_OPTION_FULL,
310 ZBC_ZONE_REPORTING_OPTION_READONLY,
311 ZBC_ZONE_REPORTING_OPTION_OFFLINE,
312 ZBC_ZONE_REPORTING_OPTION_NEED_RESET_WP = 0x10,
313 ZBC_ZONE_REPORTING_OPTION_NON_SEQWRITE,
314 ZBC_ZONE_REPORTING_OPTION_NON_WP = 0x3f,
315};
316
317#define ZBC_REPORT_ZONE_PARTIAL 0x80
318
319#endif /* _SCSI_PROTO_H_ */