1#
  2# Freescale device configuration
  3#
  4
  5config NET_VENDOR_FREESCALE
  6	bool "Freescale devices"
  7	default y
  8	depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
  9		   M523x || M527x || M5272 || M528x || M520x || M532x || \
 10		   ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) || \
 11		   ARCH_LAYERSCAPE || COMPILE_TEST
 12	---help---
 13	  If you have a network (Ethernet) card belonging to this class, say Y.
 14
 15	  Note that the answer to this question doesn't directly affect the
 16	  kernel: saying N will just cause the configurator to skip all
 17	  the questions about Freescale devices. If you say Y, you will be
 18	  asked for your specific card in the following questions.
 19
 20if NET_VENDOR_FREESCALE
 21
 22config FEC
 23	tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
 24	depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
 25		   ARCH_MXC || SOC_IMX28)
 26	default ARCH_MXC || SOC_IMX28 if ARM
 27	select PHYLIB
 28	imply PTP_1588_CLOCK
 29	---help---
 30	  Say Y here if you want to use the built-in 10/100 Fast ethernet
 31	  controller on some Motorola ColdFire and Freescale i.MX processors.
 32
 33config FEC_MPC52xx
 34	tristate "FEC MPC52xx driver"
 35	depends on PPC_MPC52xx && PPC_BESTCOMM
 36	select CRC32
 37	select PHYLIB
 38	select PPC_BESTCOMM_FEC
 39	---help---
 40	  This option enables support for the MPC5200's on-chip
 41	  Fast Ethernet Controller
 42	  If compiled as module, it will be called fec_mpc52xx.
 43
 44config FEC_MPC52xx_MDIO
 45	bool "FEC MPC52xx MDIO bus driver"
 46	depends on FEC_MPC52xx
 47	default y
 48	---help---
 49	  The MPC5200's FEC can connect to the Ethernet either with
 50	  an external MII PHY chip or 10 Mbps 7-wire interface
 51	  (Motorola? industry standard).
 52	  If your board uses an external PHY connected to FEC, enable this.
 53	  If not sure, enable.
 54	  If compiled as module, it will be called fec_mpc52xx_phy.
 55
 56source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
 57source "drivers/net/ethernet/freescale/fman/Kconfig"
 58
 59config FSL_PQ_MDIO
 60	tristate "Freescale PQ MDIO"
 61	select PHYLIB
 62	---help---
 63	  This driver supports the MDIO bus used by the gianfar and UCC drivers.
 64
 65config FSL_XGMAC_MDIO
 66	tristate "Freescale XGMAC MDIO"
 67	select PHYLIB
 68	depends on OF
 69	select OF_MDIO
 70	---help---
 71	  This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and
 72	  on the FMan mEMAC (which supports both Clauses 22 and 45)
 73
 74config UCC_GETH
 75	tristate "Freescale QE Gigabit Ethernet"
 76	depends on QUICC_ENGINE
 77	select FSL_PQ_MDIO
 78	select PHYLIB
 79	---help---
 80	  This driver supports the Gigabit Ethernet mode of the QUICC Engine,
 81	  which is available on some Freescale SOCs.
 82
 83config UGETH_TX_ON_DEMAND
 84	bool "Transmit on Demand support"
 85	depends on UCC_GETH
 86
 87config GIANFAR
 88	tristate "Gianfar Ethernet"
 89	depends on HAS_DMA
 90	select FSL_PQ_MDIO
 91	select PHYLIB
 92	select CRC32
 93	---help---
 94	  This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
 95	  and MPC86xx family of chips, the eTSEC on LS1021A and the FEC
 96	  on the 8540.
 97
 98source "drivers/net/ethernet/freescale/dpaa/Kconfig"
 99
100endif # NET_VENDOR_FREESCALE