Loading...
1/*
2 * Driver for OMAP-UART controller.
3 * Based on drivers/serial/8250.c
4 *
5 * Copyright (C) 2010 Texas Instruments.
6 *
7 * Authors:
8 * Govindraj R <govindraj.raja@ti.com>
9 * Thara Gopinath <thara@ti.com>
10 *
11 * This program is free software; you can redistribute it and/or modify
12 * it under the terms of the GNU General Public License as published by
13 * the Free Software Foundation; either version 2 of the License, or
14 * (at your option) any later version.
15 *
16 * Note: This driver is made separate from 8250 driver as we cannot
17 * over load 8250 driver with omap platform specific configuration for
18 * features like DMA, it makes easier to implement features like DMA and
19 * hardware flow control and software flow control configuration with
20 * this driver as required for the omap-platform.
21 */
22
23#if defined(CONFIG_SERIAL_OMAP_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
24#define SUPPORT_SYSRQ
25#endif
26
27#include <linux/module.h>
28#include <linux/init.h>
29#include <linux/console.h>
30#include <linux/serial_reg.h>
31#include <linux/delay.h>
32#include <linux/slab.h>
33#include <linux/tty.h>
34#include <linux/tty_flip.h>
35#include <linux/io.h>
36#include <linux/dma-mapping.h>
37#include <linux/clk.h>
38#include <linux/serial_core.h>
39#include <linux/irq.h>
40
41#include <plat/dma.h>
42#include <plat/dmtimer.h>
43#include <plat/omap-serial.h>
44
45static struct uart_omap_port *ui[OMAP_MAX_HSUART_PORTS];
46
47/* Forward declaration of functions */
48static void uart_tx_dma_callback(int lch, u16 ch_status, void *data);
49static void serial_omap_rx_timeout(unsigned long uart_no);
50static int serial_omap_start_rxdma(struct uart_omap_port *up);
51
52static inline unsigned int serial_in(struct uart_omap_port *up, int offset)
53{
54 offset <<= up->port.regshift;
55 return readw(up->port.membase + offset);
56}
57
58static inline void serial_out(struct uart_omap_port *up, int offset, int value)
59{
60 offset <<= up->port.regshift;
61 writew(value, up->port.membase + offset);
62}
63
64static inline void serial_omap_clear_fifos(struct uart_omap_port *up)
65{
66 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
67 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
68 UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
69 serial_out(up, UART_FCR, 0);
70}
71
72/*
73 * serial_omap_get_divisor - calculate divisor value
74 * @port: uart port info
75 * @baud: baudrate for which divisor needs to be calculated.
76 *
77 * We have written our own function to get the divisor so as to support
78 * 13x mode. 3Mbps Baudrate as an different divisor.
79 * Reference OMAP TRM Chapter 17:
80 * Table 17-1. UART Mode Baud Rates, Divisor Values, and Error Rates
81 * referring to oversampling - divisor value
82 * baudrate 460,800 to 3,686,400 all have divisor 13
83 * except 3,000,000 which has divisor value 16
84 */
85static unsigned int
86serial_omap_get_divisor(struct uart_port *port, unsigned int baud)
87{
88 unsigned int divisor;
89
90 if (baud > OMAP_MODE13X_SPEED && baud != 3000000)
91 divisor = 13;
92 else
93 divisor = 16;
94 return port->uartclk/(baud * divisor);
95}
96
97static void serial_omap_stop_rxdma(struct uart_omap_port *up)
98{
99 if (up->uart_dma.rx_dma_used) {
100 del_timer(&up->uart_dma.rx_timer);
101 omap_stop_dma(up->uart_dma.rx_dma_channel);
102 omap_free_dma(up->uart_dma.rx_dma_channel);
103 up->uart_dma.rx_dma_channel = OMAP_UART_DMA_CH_FREE;
104 up->uart_dma.rx_dma_used = false;
105 }
106}
107
108static void serial_omap_enable_ms(struct uart_port *port)
109{
110 struct uart_omap_port *up = (struct uart_omap_port *)port;
111
112 dev_dbg(up->port.dev, "serial_omap_enable_ms+%d\n", up->pdev->id);
113 up->ier |= UART_IER_MSI;
114 serial_out(up, UART_IER, up->ier);
115}
116
117static void serial_omap_stop_tx(struct uart_port *port)
118{
119 struct uart_omap_port *up = (struct uart_omap_port *)port;
120
121 if (up->use_dma &&
122 up->uart_dma.tx_dma_channel != OMAP_UART_DMA_CH_FREE) {
123 /*
124 * Check if dma is still active. If yes do nothing,
125 * return. Else stop dma
126 */
127 if (omap_get_dma_active_status(up->uart_dma.tx_dma_channel))
128 return;
129 omap_stop_dma(up->uart_dma.tx_dma_channel);
130 omap_free_dma(up->uart_dma.tx_dma_channel);
131 up->uart_dma.tx_dma_channel = OMAP_UART_DMA_CH_FREE;
132 }
133
134 if (up->ier & UART_IER_THRI) {
135 up->ier &= ~UART_IER_THRI;
136 serial_out(up, UART_IER, up->ier);
137 }
138}
139
140static void serial_omap_stop_rx(struct uart_port *port)
141{
142 struct uart_omap_port *up = (struct uart_omap_port *)port;
143
144 if (up->use_dma)
145 serial_omap_stop_rxdma(up);
146 up->ier &= ~UART_IER_RLSI;
147 up->port.read_status_mask &= ~UART_LSR_DR;
148 serial_out(up, UART_IER, up->ier);
149}
150
151static inline void receive_chars(struct uart_omap_port *up, int *status)
152{
153 struct tty_struct *tty = up->port.state->port.tty;
154 unsigned int flag;
155 unsigned char ch, lsr = *status;
156 int max_count = 256;
157
158 do {
159 if (likely(lsr & UART_LSR_DR))
160 ch = serial_in(up, UART_RX);
161 flag = TTY_NORMAL;
162 up->port.icount.rx++;
163
164 if (unlikely(lsr & UART_LSR_BRK_ERROR_BITS)) {
165 /*
166 * For statistics only
167 */
168 if (lsr & UART_LSR_BI) {
169 lsr &= ~(UART_LSR_FE | UART_LSR_PE);
170 up->port.icount.brk++;
171 /*
172 * We do the SysRQ and SAK checking
173 * here because otherwise the break
174 * may get masked by ignore_status_mask
175 * or read_status_mask.
176 */
177 if (uart_handle_break(&up->port))
178 goto ignore_char;
179 } else if (lsr & UART_LSR_PE) {
180 up->port.icount.parity++;
181 } else if (lsr & UART_LSR_FE) {
182 up->port.icount.frame++;
183 }
184
185 if (lsr & UART_LSR_OE)
186 up->port.icount.overrun++;
187
188 /*
189 * Mask off conditions which should be ignored.
190 */
191 lsr &= up->port.read_status_mask;
192
193#ifdef CONFIG_SERIAL_OMAP_CONSOLE
194 if (up->port.line == up->port.cons->index) {
195 /* Recover the break flag from console xmit */
196 lsr |= up->lsr_break_flag;
197 }
198#endif
199 if (lsr & UART_LSR_BI)
200 flag = TTY_BREAK;
201 else if (lsr & UART_LSR_PE)
202 flag = TTY_PARITY;
203 else if (lsr & UART_LSR_FE)
204 flag = TTY_FRAME;
205 }
206
207 if (uart_handle_sysrq_char(&up->port, ch))
208 goto ignore_char;
209 uart_insert_char(&up->port, lsr, UART_LSR_OE, ch, flag);
210ignore_char:
211 lsr = serial_in(up, UART_LSR);
212 } while ((lsr & (UART_LSR_DR | UART_LSR_BI)) && (max_count-- > 0));
213 spin_unlock(&up->port.lock);
214 tty_flip_buffer_push(tty);
215 spin_lock(&up->port.lock);
216}
217
218static void transmit_chars(struct uart_omap_port *up)
219{
220 struct circ_buf *xmit = &up->port.state->xmit;
221 int count;
222
223 if (up->port.x_char) {
224 serial_out(up, UART_TX, up->port.x_char);
225 up->port.icount.tx++;
226 up->port.x_char = 0;
227 return;
228 }
229 if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
230 serial_omap_stop_tx(&up->port);
231 return;
232 }
233 count = up->port.fifosize / 4;
234 do {
235 serial_out(up, UART_TX, xmit->buf[xmit->tail]);
236 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
237 up->port.icount.tx++;
238 if (uart_circ_empty(xmit))
239 break;
240 } while (--count > 0);
241
242 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
243 uart_write_wakeup(&up->port);
244
245 if (uart_circ_empty(xmit))
246 serial_omap_stop_tx(&up->port);
247}
248
249static inline void serial_omap_enable_ier_thri(struct uart_omap_port *up)
250{
251 if (!(up->ier & UART_IER_THRI)) {
252 up->ier |= UART_IER_THRI;
253 serial_out(up, UART_IER, up->ier);
254 }
255}
256
257static void serial_omap_start_tx(struct uart_port *port)
258{
259 struct uart_omap_port *up = (struct uart_omap_port *)port;
260 struct circ_buf *xmit;
261 unsigned int start;
262 int ret = 0;
263
264 if (!up->use_dma) {
265 serial_omap_enable_ier_thri(up);
266 return;
267 }
268
269 if (up->uart_dma.tx_dma_used)
270 return;
271
272 xmit = &up->port.state->xmit;
273
274 if (up->uart_dma.tx_dma_channel == OMAP_UART_DMA_CH_FREE) {
275 ret = omap_request_dma(up->uart_dma.uart_dma_tx,
276 "UART Tx DMA",
277 (void *)uart_tx_dma_callback, up,
278 &(up->uart_dma.tx_dma_channel));
279
280 if (ret < 0) {
281 serial_omap_enable_ier_thri(up);
282 return;
283 }
284 }
285 spin_lock(&(up->uart_dma.tx_lock));
286 up->uart_dma.tx_dma_used = true;
287 spin_unlock(&(up->uart_dma.tx_lock));
288
289 start = up->uart_dma.tx_buf_dma_phys +
290 (xmit->tail & (UART_XMIT_SIZE - 1));
291
292 up->uart_dma.tx_buf_size = uart_circ_chars_pending(xmit);
293 /*
294 * It is a circular buffer. See if the buffer has wounded back.
295 * If yes it will have to be transferred in two separate dma
296 * transfers
297 */
298 if (start + up->uart_dma.tx_buf_size >=
299 up->uart_dma.tx_buf_dma_phys + UART_XMIT_SIZE)
300 up->uart_dma.tx_buf_size =
301 (up->uart_dma.tx_buf_dma_phys +
302 UART_XMIT_SIZE) - start;
303
304 omap_set_dma_dest_params(up->uart_dma.tx_dma_channel, 0,
305 OMAP_DMA_AMODE_CONSTANT,
306 up->uart_dma.uart_base, 0, 0);
307 omap_set_dma_src_params(up->uart_dma.tx_dma_channel, 0,
308 OMAP_DMA_AMODE_POST_INC, start, 0, 0);
309 omap_set_dma_transfer_params(up->uart_dma.tx_dma_channel,
310 OMAP_DMA_DATA_TYPE_S8,
311 up->uart_dma.tx_buf_size, 1,
312 OMAP_DMA_SYNC_ELEMENT,
313 up->uart_dma.uart_dma_tx, 0);
314 /* FIXME: Cache maintenance needed here? */
315 omap_start_dma(up->uart_dma.tx_dma_channel);
316}
317
318static unsigned int check_modem_status(struct uart_omap_port *up)
319{
320 unsigned int status;
321
322 status = serial_in(up, UART_MSR);
323 status |= up->msr_saved_flags;
324 up->msr_saved_flags = 0;
325 if ((status & UART_MSR_ANY_DELTA) == 0)
326 return status;
327
328 if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI &&
329 up->port.state != NULL) {
330 if (status & UART_MSR_TERI)
331 up->port.icount.rng++;
332 if (status & UART_MSR_DDSR)
333 up->port.icount.dsr++;
334 if (status & UART_MSR_DDCD)
335 uart_handle_dcd_change
336 (&up->port, status & UART_MSR_DCD);
337 if (status & UART_MSR_DCTS)
338 uart_handle_cts_change
339 (&up->port, status & UART_MSR_CTS);
340 wake_up_interruptible(&up->port.state->port.delta_msr_wait);
341 }
342
343 return status;
344}
345
346/**
347 * serial_omap_irq() - This handles the interrupt from one port
348 * @irq: uart port irq number
349 * @dev_id: uart port info
350 */
351static inline irqreturn_t serial_omap_irq(int irq, void *dev_id)
352{
353 struct uart_omap_port *up = dev_id;
354 unsigned int iir, lsr;
355 unsigned long flags;
356
357 iir = serial_in(up, UART_IIR);
358 if (iir & UART_IIR_NO_INT)
359 return IRQ_NONE;
360
361 spin_lock_irqsave(&up->port.lock, flags);
362 lsr = serial_in(up, UART_LSR);
363 if (iir & UART_IIR_RLSI) {
364 if (!up->use_dma) {
365 if (lsr & UART_LSR_DR)
366 receive_chars(up, &lsr);
367 } else {
368 up->ier &= ~(UART_IER_RDI | UART_IER_RLSI);
369 serial_out(up, UART_IER, up->ier);
370 if ((serial_omap_start_rxdma(up) != 0) &&
371 (lsr & UART_LSR_DR))
372 receive_chars(up, &lsr);
373 }
374 }
375
376 check_modem_status(up);
377 if ((lsr & UART_LSR_THRE) && (iir & UART_IIR_THRI))
378 transmit_chars(up);
379
380 spin_unlock_irqrestore(&up->port.lock, flags);
381 up->port_activity = jiffies;
382 return IRQ_HANDLED;
383}
384
385static unsigned int serial_omap_tx_empty(struct uart_port *port)
386{
387 struct uart_omap_port *up = (struct uart_omap_port *)port;
388 unsigned long flags = 0;
389 unsigned int ret = 0;
390
391 dev_dbg(up->port.dev, "serial_omap_tx_empty+%d\n", up->pdev->id);
392 spin_lock_irqsave(&up->port.lock, flags);
393 ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
394 spin_unlock_irqrestore(&up->port.lock, flags);
395
396 return ret;
397}
398
399static unsigned int serial_omap_get_mctrl(struct uart_port *port)
400{
401 struct uart_omap_port *up = (struct uart_omap_port *)port;
402 unsigned char status;
403 unsigned int ret = 0;
404
405 status = check_modem_status(up);
406 dev_dbg(up->port.dev, "serial_omap_get_mctrl+%d\n", up->pdev->id);
407
408 if (status & UART_MSR_DCD)
409 ret |= TIOCM_CAR;
410 if (status & UART_MSR_RI)
411 ret |= TIOCM_RNG;
412 if (status & UART_MSR_DSR)
413 ret |= TIOCM_DSR;
414 if (status & UART_MSR_CTS)
415 ret |= TIOCM_CTS;
416 return ret;
417}
418
419static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl)
420{
421 struct uart_omap_port *up = (struct uart_omap_port *)port;
422 unsigned char mcr = 0;
423
424 dev_dbg(up->port.dev, "serial_omap_set_mctrl+%d\n", up->pdev->id);
425 if (mctrl & TIOCM_RTS)
426 mcr |= UART_MCR_RTS;
427 if (mctrl & TIOCM_DTR)
428 mcr |= UART_MCR_DTR;
429 if (mctrl & TIOCM_OUT1)
430 mcr |= UART_MCR_OUT1;
431 if (mctrl & TIOCM_OUT2)
432 mcr |= UART_MCR_OUT2;
433 if (mctrl & TIOCM_LOOP)
434 mcr |= UART_MCR_LOOP;
435
436 mcr |= up->mcr;
437 serial_out(up, UART_MCR, mcr);
438}
439
440static void serial_omap_break_ctl(struct uart_port *port, int break_state)
441{
442 struct uart_omap_port *up = (struct uart_omap_port *)port;
443 unsigned long flags = 0;
444
445 dev_dbg(up->port.dev, "serial_omap_break_ctl+%d\n", up->pdev->id);
446 spin_lock_irqsave(&up->port.lock, flags);
447 if (break_state == -1)
448 up->lcr |= UART_LCR_SBC;
449 else
450 up->lcr &= ~UART_LCR_SBC;
451 serial_out(up, UART_LCR, up->lcr);
452 spin_unlock_irqrestore(&up->port.lock, flags);
453}
454
455static int serial_omap_startup(struct uart_port *port)
456{
457 struct uart_omap_port *up = (struct uart_omap_port *)port;
458 unsigned long flags = 0;
459 int retval;
460
461 /*
462 * Allocate the IRQ
463 */
464 retval = request_irq(up->port.irq, serial_omap_irq, up->port.irqflags,
465 up->name, up);
466 if (retval)
467 return retval;
468
469 dev_dbg(up->port.dev, "serial_omap_startup+%d\n", up->pdev->id);
470
471 /*
472 * Clear the FIFO buffers and disable them.
473 * (they will be reenabled in set_termios())
474 */
475 serial_omap_clear_fifos(up);
476 /* For Hardware flow control */
477 serial_out(up, UART_MCR, UART_MCR_RTS);
478
479 /*
480 * Clear the interrupt registers.
481 */
482 (void) serial_in(up, UART_LSR);
483 if (serial_in(up, UART_LSR) & UART_LSR_DR)
484 (void) serial_in(up, UART_RX);
485 (void) serial_in(up, UART_IIR);
486 (void) serial_in(up, UART_MSR);
487
488 /*
489 * Now, initialize the UART
490 */
491 serial_out(up, UART_LCR, UART_LCR_WLEN8);
492 spin_lock_irqsave(&up->port.lock, flags);
493 /*
494 * Most PC uarts need OUT2 raised to enable interrupts.
495 */
496 up->port.mctrl |= TIOCM_OUT2;
497 serial_omap_set_mctrl(&up->port, up->port.mctrl);
498 spin_unlock_irqrestore(&up->port.lock, flags);
499
500 up->msr_saved_flags = 0;
501 if (up->use_dma) {
502 free_page((unsigned long)up->port.state->xmit.buf);
503 up->port.state->xmit.buf = dma_alloc_coherent(NULL,
504 UART_XMIT_SIZE,
505 (dma_addr_t *)&(up->uart_dma.tx_buf_dma_phys),
506 0);
507 init_timer(&(up->uart_dma.rx_timer));
508 up->uart_dma.rx_timer.function = serial_omap_rx_timeout;
509 up->uart_dma.rx_timer.data = up->pdev->id;
510 /* Currently the buffer size is 4KB. Can increase it */
511 up->uart_dma.rx_buf = dma_alloc_coherent(NULL,
512 up->uart_dma.rx_buf_size,
513 (dma_addr_t *)&(up->uart_dma.rx_buf_dma_phys), 0);
514 }
515 /*
516 * Finally, enable interrupts. Note: Modem status interrupts
517 * are set via set_termios(), which will be occurring imminently
518 * anyway, so we don't enable them here.
519 */
520 up->ier = UART_IER_RLSI | UART_IER_RDI;
521 serial_out(up, UART_IER, up->ier);
522
523 /* Enable module level wake up */
524 serial_out(up, UART_OMAP_WER, OMAP_UART_WER_MOD_WKUP);
525
526 up->port_activity = jiffies;
527 return 0;
528}
529
530static void serial_omap_shutdown(struct uart_port *port)
531{
532 struct uart_omap_port *up = (struct uart_omap_port *)port;
533 unsigned long flags = 0;
534
535 dev_dbg(up->port.dev, "serial_omap_shutdown+%d\n", up->pdev->id);
536 /*
537 * Disable interrupts from this port
538 */
539 up->ier = 0;
540 serial_out(up, UART_IER, 0);
541
542 spin_lock_irqsave(&up->port.lock, flags);
543 up->port.mctrl &= ~TIOCM_OUT2;
544 serial_omap_set_mctrl(&up->port, up->port.mctrl);
545 spin_unlock_irqrestore(&up->port.lock, flags);
546
547 /*
548 * Disable break condition and FIFOs
549 */
550 serial_out(up, UART_LCR, serial_in(up, UART_LCR) & ~UART_LCR_SBC);
551 serial_omap_clear_fifos(up);
552
553 /*
554 * Read data port to reset things, and then free the irq
555 */
556 if (serial_in(up, UART_LSR) & UART_LSR_DR)
557 (void) serial_in(up, UART_RX);
558 if (up->use_dma) {
559 dma_free_coherent(up->port.dev,
560 UART_XMIT_SIZE, up->port.state->xmit.buf,
561 up->uart_dma.tx_buf_dma_phys);
562 up->port.state->xmit.buf = NULL;
563 serial_omap_stop_rx(port);
564 dma_free_coherent(up->port.dev,
565 up->uart_dma.rx_buf_size, up->uart_dma.rx_buf,
566 up->uart_dma.rx_buf_dma_phys);
567 up->uart_dma.rx_buf = NULL;
568 }
569 free_irq(up->port.irq, up);
570}
571
572static inline void
573serial_omap_configure_xonxoff
574 (struct uart_omap_port *up, struct ktermios *termios)
575{
576 unsigned char efr = 0;
577
578 up->lcr = serial_in(up, UART_LCR);
579 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
580 up->efr = serial_in(up, UART_EFR);
581 serial_out(up, UART_EFR, up->efr & ~UART_EFR_ECB);
582
583 serial_out(up, UART_XON1, termios->c_cc[VSTART]);
584 serial_out(up, UART_XOFF1, termios->c_cc[VSTOP]);
585
586 /* clear SW control mode bits */
587 efr = up->efr;
588 efr &= OMAP_UART_SW_CLR;
589
590 /*
591 * IXON Flag:
592 * Enable XON/XOFF flow control on output.
593 * Transmit XON1, XOFF1
594 */
595 if (termios->c_iflag & IXON)
596 efr |= OMAP_UART_SW_TX;
597
598 /*
599 * IXOFF Flag:
600 * Enable XON/XOFF flow control on input.
601 * Receiver compares XON1, XOFF1.
602 */
603 if (termios->c_iflag & IXOFF)
604 efr |= OMAP_UART_SW_RX;
605
606 serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
607 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
608
609 up->mcr = serial_in(up, UART_MCR);
610
611 /*
612 * IXANY Flag:
613 * Enable any character to restart output.
614 * Operation resumes after receiving any
615 * character after recognition of the XOFF character
616 */
617 if (termios->c_iflag & IXANY)
618 up->mcr |= UART_MCR_XONANY;
619
620 serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
621 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
622 serial_out(up, UART_TI752_TCR, OMAP_UART_TCR_TRIG);
623 /* Enable special char function UARTi.EFR_REG[5] and
624 * load the new software flow control mode IXON or IXOFF
625 * and restore the UARTi.EFR_REG[4] ENHANCED_EN value.
626 */
627 serial_out(up, UART_EFR, efr | UART_EFR_SCD);
628 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
629
630 serial_out(up, UART_MCR, up->mcr & ~UART_MCR_TCRTLR);
631 serial_out(up, UART_LCR, up->lcr);
632}
633
634static void
635serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
636 struct ktermios *old)
637{
638 struct uart_omap_port *up = (struct uart_omap_port *)port;
639 unsigned char cval = 0;
640 unsigned char efr = 0;
641 unsigned long flags = 0;
642 unsigned int baud, quot;
643
644 switch (termios->c_cflag & CSIZE) {
645 case CS5:
646 cval = UART_LCR_WLEN5;
647 break;
648 case CS6:
649 cval = UART_LCR_WLEN6;
650 break;
651 case CS7:
652 cval = UART_LCR_WLEN7;
653 break;
654 default:
655 case CS8:
656 cval = UART_LCR_WLEN8;
657 break;
658 }
659
660 if (termios->c_cflag & CSTOPB)
661 cval |= UART_LCR_STOP;
662 if (termios->c_cflag & PARENB)
663 cval |= UART_LCR_PARITY;
664 if (!(termios->c_cflag & PARODD))
665 cval |= UART_LCR_EPAR;
666
667 /*
668 * Ask the core to calculate the divisor for us.
669 */
670
671 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/13);
672 quot = serial_omap_get_divisor(port, baud);
673
674 up->fcr = UART_FCR_R_TRIG_01 | UART_FCR_T_TRIG_01 |
675 UART_FCR_ENABLE_FIFO;
676 if (up->use_dma)
677 up->fcr |= UART_FCR_DMA_SELECT;
678
679 /*
680 * Ok, we're now changing the port state. Do it with
681 * interrupts disabled.
682 */
683 spin_lock_irqsave(&up->port.lock, flags);
684
685 /*
686 * Update the per-port timeout.
687 */
688 uart_update_timeout(port, termios->c_cflag, baud);
689
690 up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
691 if (termios->c_iflag & INPCK)
692 up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
693 if (termios->c_iflag & (BRKINT | PARMRK))
694 up->port.read_status_mask |= UART_LSR_BI;
695
696 /*
697 * Characters to ignore
698 */
699 up->port.ignore_status_mask = 0;
700 if (termios->c_iflag & IGNPAR)
701 up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
702 if (termios->c_iflag & IGNBRK) {
703 up->port.ignore_status_mask |= UART_LSR_BI;
704 /*
705 * If we're ignoring parity and break indicators,
706 * ignore overruns too (for real raw support).
707 */
708 if (termios->c_iflag & IGNPAR)
709 up->port.ignore_status_mask |= UART_LSR_OE;
710 }
711
712 /*
713 * ignore all characters if CREAD is not set
714 */
715 if ((termios->c_cflag & CREAD) == 0)
716 up->port.ignore_status_mask |= UART_LSR_DR;
717
718 /*
719 * Modem status interrupts
720 */
721 up->ier &= ~UART_IER_MSI;
722 if (UART_ENABLE_MS(&up->port, termios->c_cflag))
723 up->ier |= UART_IER_MSI;
724 serial_out(up, UART_IER, up->ier);
725 serial_out(up, UART_LCR, cval); /* reset DLAB */
726
727 /* FIFOs and DMA Settings */
728
729 /* FCR can be changed only when the
730 * baud clock is not running
731 * DLL_REG and DLH_REG set to 0.
732 */
733 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
734 serial_out(up, UART_DLL, 0);
735 serial_out(up, UART_DLM, 0);
736 serial_out(up, UART_LCR, 0);
737
738 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
739
740 up->efr = serial_in(up, UART_EFR);
741 serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
742
743 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
744 up->mcr = serial_in(up, UART_MCR);
745 serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
746 /* FIFO ENABLE, DMA MODE */
747 serial_out(up, UART_FCR, up->fcr);
748 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
749
750 if (up->use_dma) {
751 serial_out(up, UART_TI752_TLR, 0);
752 serial_out(up, UART_OMAP_SCR,
753 (UART_FCR_TRIGGER_4 | UART_FCR_TRIGGER_8));
754 }
755
756 serial_out(up, UART_EFR, up->efr);
757 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
758 serial_out(up, UART_MCR, up->mcr);
759
760 /* Protocol, Baud Rate, and Interrupt Settings */
761
762 serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_DISABLE);
763 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
764
765 up->efr = serial_in(up, UART_EFR);
766 serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
767
768 serial_out(up, UART_LCR, 0);
769 serial_out(up, UART_IER, 0);
770 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
771
772 serial_out(up, UART_DLL, quot & 0xff); /* LS of divisor */
773 serial_out(up, UART_DLM, quot >> 8); /* MS of divisor */
774
775 serial_out(up, UART_LCR, 0);
776 serial_out(up, UART_IER, up->ier);
777 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
778
779 serial_out(up, UART_EFR, up->efr);
780 serial_out(up, UART_LCR, cval);
781
782 if (baud > 230400 && baud != 3000000)
783 serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_13X_MODE);
784 else
785 serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_16X_MODE);
786
787 /* Hardware Flow Control Configuration */
788
789 if (termios->c_cflag & CRTSCTS) {
790 efr |= (UART_EFR_CTS | UART_EFR_RTS);
791 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
792
793 up->mcr = serial_in(up, UART_MCR);
794 serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
795
796 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
797 up->efr = serial_in(up, UART_EFR);
798 serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
799
800 serial_out(up, UART_TI752_TCR, OMAP_UART_TCR_TRIG);
801 serial_out(up, UART_EFR, efr); /* Enable AUTORTS and AUTOCTS */
802 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
803 serial_out(up, UART_MCR, up->mcr | UART_MCR_RTS);
804 serial_out(up, UART_LCR, cval);
805 }
806
807 serial_omap_set_mctrl(&up->port, up->port.mctrl);
808 /* Software Flow Control Configuration */
809 serial_omap_configure_xonxoff(up, termios);
810
811 spin_unlock_irqrestore(&up->port.lock, flags);
812 dev_dbg(up->port.dev, "serial_omap_set_termios+%d\n", up->pdev->id);
813}
814
815static void
816serial_omap_pm(struct uart_port *port, unsigned int state,
817 unsigned int oldstate)
818{
819 struct uart_omap_port *up = (struct uart_omap_port *)port;
820 unsigned char efr;
821
822 dev_dbg(up->port.dev, "serial_omap_pm+%d\n", up->pdev->id);
823 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
824 efr = serial_in(up, UART_EFR);
825 serial_out(up, UART_EFR, efr | UART_EFR_ECB);
826 serial_out(up, UART_LCR, 0);
827
828 serial_out(up, UART_IER, (state != 0) ? UART_IERX_SLEEP : 0);
829 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
830 serial_out(up, UART_EFR, efr);
831 serial_out(up, UART_LCR, 0);
832}
833
834static void serial_omap_release_port(struct uart_port *port)
835{
836 dev_dbg(port->dev, "serial_omap_release_port+\n");
837}
838
839static int serial_omap_request_port(struct uart_port *port)
840{
841 dev_dbg(port->dev, "serial_omap_request_port+\n");
842 return 0;
843}
844
845static void serial_omap_config_port(struct uart_port *port, int flags)
846{
847 struct uart_omap_port *up = (struct uart_omap_port *)port;
848
849 dev_dbg(up->port.dev, "serial_omap_config_port+%d\n",
850 up->pdev->id);
851 up->port.type = PORT_OMAP;
852}
853
854static int
855serial_omap_verify_port(struct uart_port *port, struct serial_struct *ser)
856{
857 /* we don't want the core code to modify any port params */
858 dev_dbg(port->dev, "serial_omap_verify_port+\n");
859 return -EINVAL;
860}
861
862static const char *
863serial_omap_type(struct uart_port *port)
864{
865 struct uart_omap_port *up = (struct uart_omap_port *)port;
866
867 dev_dbg(up->port.dev, "serial_omap_type+%d\n", up->pdev->id);
868 return up->name;
869}
870
871#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
872
873static inline void wait_for_xmitr(struct uart_omap_port *up)
874{
875 unsigned int status, tmout = 10000;
876
877 /* Wait up to 10ms for the character(s) to be sent. */
878 do {
879 status = serial_in(up, UART_LSR);
880
881 if (status & UART_LSR_BI)
882 up->lsr_break_flag = UART_LSR_BI;
883
884 if (--tmout == 0)
885 break;
886 udelay(1);
887 } while ((status & BOTH_EMPTY) != BOTH_EMPTY);
888
889 /* Wait up to 1s for flow control if necessary */
890 if (up->port.flags & UPF_CONS_FLOW) {
891 tmout = 1000000;
892 for (tmout = 1000000; tmout; tmout--) {
893 unsigned int msr = serial_in(up, UART_MSR);
894
895 up->msr_saved_flags |= msr & MSR_SAVE_FLAGS;
896 if (msr & UART_MSR_CTS)
897 break;
898
899 udelay(1);
900 }
901 }
902}
903
904#ifdef CONFIG_CONSOLE_POLL
905
906static void serial_omap_poll_put_char(struct uart_port *port, unsigned char ch)
907{
908 struct uart_omap_port *up = (struct uart_omap_port *)port;
909 wait_for_xmitr(up);
910 serial_out(up, UART_TX, ch);
911}
912
913static int serial_omap_poll_get_char(struct uart_port *port)
914{
915 struct uart_omap_port *up = (struct uart_omap_port *)port;
916 unsigned int status = serial_in(up, UART_LSR);
917
918 if (!(status & UART_LSR_DR))
919 return NO_POLL_CHAR;
920
921 return serial_in(up, UART_RX);
922}
923
924#endif /* CONFIG_CONSOLE_POLL */
925
926#ifdef CONFIG_SERIAL_OMAP_CONSOLE
927
928static struct uart_omap_port *serial_omap_console_ports[4];
929
930static struct uart_driver serial_omap_reg;
931
932static void serial_omap_console_putchar(struct uart_port *port, int ch)
933{
934 struct uart_omap_port *up = (struct uart_omap_port *)port;
935
936 wait_for_xmitr(up);
937 serial_out(up, UART_TX, ch);
938}
939
940static void
941serial_omap_console_write(struct console *co, const char *s,
942 unsigned int count)
943{
944 struct uart_omap_port *up = serial_omap_console_ports[co->index];
945 unsigned long flags;
946 unsigned int ier;
947 int locked = 1;
948
949 local_irq_save(flags);
950 if (up->port.sysrq)
951 locked = 0;
952 else if (oops_in_progress)
953 locked = spin_trylock(&up->port.lock);
954 else
955 spin_lock(&up->port.lock);
956
957 /*
958 * First save the IER then disable the interrupts
959 */
960 ier = serial_in(up, UART_IER);
961 serial_out(up, UART_IER, 0);
962
963 uart_console_write(&up->port, s, count, serial_omap_console_putchar);
964
965 /*
966 * Finally, wait for transmitter to become empty
967 * and restore the IER
968 */
969 wait_for_xmitr(up);
970 serial_out(up, UART_IER, ier);
971 /*
972 * The receive handling will happen properly because the
973 * receive ready bit will still be set; it is not cleared
974 * on read. However, modem control will not, we must
975 * call it if we have saved something in the saved flags
976 * while processing with interrupts off.
977 */
978 if (up->msr_saved_flags)
979 check_modem_status(up);
980
981 if (locked)
982 spin_unlock(&up->port.lock);
983 local_irq_restore(flags);
984}
985
986static int __init
987serial_omap_console_setup(struct console *co, char *options)
988{
989 struct uart_omap_port *up;
990 int baud = 115200;
991 int bits = 8;
992 int parity = 'n';
993 int flow = 'n';
994
995 if (serial_omap_console_ports[co->index] == NULL)
996 return -ENODEV;
997 up = serial_omap_console_ports[co->index];
998
999 if (options)
1000 uart_parse_options(options, &baud, &parity, &bits, &flow);
1001
1002 return uart_set_options(&up->port, co, baud, parity, bits, flow);
1003}
1004
1005static struct console serial_omap_console = {
1006 .name = OMAP_SERIAL_NAME,
1007 .write = serial_omap_console_write,
1008 .device = uart_console_device,
1009 .setup = serial_omap_console_setup,
1010 .flags = CON_PRINTBUFFER,
1011 .index = -1,
1012 .data = &serial_omap_reg,
1013};
1014
1015static void serial_omap_add_console_port(struct uart_omap_port *up)
1016{
1017 serial_omap_console_ports[up->pdev->id] = up;
1018}
1019
1020#define OMAP_CONSOLE (&serial_omap_console)
1021
1022#else
1023
1024#define OMAP_CONSOLE NULL
1025
1026static inline void serial_omap_add_console_port(struct uart_omap_port *up)
1027{}
1028
1029#endif
1030
1031static struct uart_ops serial_omap_pops = {
1032 .tx_empty = serial_omap_tx_empty,
1033 .set_mctrl = serial_omap_set_mctrl,
1034 .get_mctrl = serial_omap_get_mctrl,
1035 .stop_tx = serial_omap_stop_tx,
1036 .start_tx = serial_omap_start_tx,
1037 .stop_rx = serial_omap_stop_rx,
1038 .enable_ms = serial_omap_enable_ms,
1039 .break_ctl = serial_omap_break_ctl,
1040 .startup = serial_omap_startup,
1041 .shutdown = serial_omap_shutdown,
1042 .set_termios = serial_omap_set_termios,
1043 .pm = serial_omap_pm,
1044 .type = serial_omap_type,
1045 .release_port = serial_omap_release_port,
1046 .request_port = serial_omap_request_port,
1047 .config_port = serial_omap_config_port,
1048 .verify_port = serial_omap_verify_port,
1049#ifdef CONFIG_CONSOLE_POLL
1050 .poll_put_char = serial_omap_poll_put_char,
1051 .poll_get_char = serial_omap_poll_get_char,
1052#endif
1053};
1054
1055static struct uart_driver serial_omap_reg = {
1056 .owner = THIS_MODULE,
1057 .driver_name = "OMAP-SERIAL",
1058 .dev_name = OMAP_SERIAL_NAME,
1059 .nr = OMAP_MAX_HSUART_PORTS,
1060 .cons = OMAP_CONSOLE,
1061};
1062
1063static int
1064serial_omap_suspend(struct platform_device *pdev, pm_message_t state)
1065{
1066 struct uart_omap_port *up = platform_get_drvdata(pdev);
1067
1068 if (up)
1069 uart_suspend_port(&serial_omap_reg, &up->port);
1070 return 0;
1071}
1072
1073static int serial_omap_resume(struct platform_device *dev)
1074{
1075 struct uart_omap_port *up = platform_get_drvdata(dev);
1076
1077 if (up)
1078 uart_resume_port(&serial_omap_reg, &up->port);
1079 return 0;
1080}
1081
1082static void serial_omap_rx_timeout(unsigned long uart_no)
1083{
1084 struct uart_omap_port *up = ui[uart_no];
1085 unsigned int curr_dma_pos, curr_transmitted_size;
1086 int ret = 0;
1087
1088 curr_dma_pos = omap_get_dma_dst_pos(up->uart_dma.rx_dma_channel);
1089 if ((curr_dma_pos == up->uart_dma.prev_rx_dma_pos) ||
1090 (curr_dma_pos == 0)) {
1091 if (jiffies_to_msecs(jiffies - up->port_activity) <
1092 RX_TIMEOUT) {
1093 mod_timer(&up->uart_dma.rx_timer, jiffies +
1094 usecs_to_jiffies(up->uart_dma.rx_timeout));
1095 } else {
1096 serial_omap_stop_rxdma(up);
1097 up->ier |= (UART_IER_RDI | UART_IER_RLSI);
1098 serial_out(up, UART_IER, up->ier);
1099 }
1100 return;
1101 }
1102
1103 curr_transmitted_size = curr_dma_pos -
1104 up->uart_dma.prev_rx_dma_pos;
1105 up->port.icount.rx += curr_transmitted_size;
1106 tty_insert_flip_string(up->port.state->port.tty,
1107 up->uart_dma.rx_buf +
1108 (up->uart_dma.prev_rx_dma_pos -
1109 up->uart_dma.rx_buf_dma_phys),
1110 curr_transmitted_size);
1111 tty_flip_buffer_push(up->port.state->port.tty);
1112 up->uart_dma.prev_rx_dma_pos = curr_dma_pos;
1113 if (up->uart_dma.rx_buf_size +
1114 up->uart_dma.rx_buf_dma_phys == curr_dma_pos) {
1115 ret = serial_omap_start_rxdma(up);
1116 if (ret < 0) {
1117 serial_omap_stop_rxdma(up);
1118 up->ier |= (UART_IER_RDI | UART_IER_RLSI);
1119 serial_out(up, UART_IER, up->ier);
1120 }
1121 } else {
1122 mod_timer(&up->uart_dma.rx_timer, jiffies +
1123 usecs_to_jiffies(up->uart_dma.rx_timeout));
1124 }
1125 up->port_activity = jiffies;
1126}
1127
1128static void uart_rx_dma_callback(int lch, u16 ch_status, void *data)
1129{
1130 return;
1131}
1132
1133static int serial_omap_start_rxdma(struct uart_omap_port *up)
1134{
1135 int ret = 0;
1136
1137 if (up->uart_dma.rx_dma_channel == -1) {
1138 ret = omap_request_dma(up->uart_dma.uart_dma_rx,
1139 "UART Rx DMA",
1140 (void *)uart_rx_dma_callback, up,
1141 &(up->uart_dma.rx_dma_channel));
1142 if (ret < 0)
1143 return ret;
1144
1145 omap_set_dma_src_params(up->uart_dma.rx_dma_channel, 0,
1146 OMAP_DMA_AMODE_CONSTANT,
1147 up->uart_dma.uart_base, 0, 0);
1148 omap_set_dma_dest_params(up->uart_dma.rx_dma_channel, 0,
1149 OMAP_DMA_AMODE_POST_INC,
1150 up->uart_dma.rx_buf_dma_phys, 0, 0);
1151 omap_set_dma_transfer_params(up->uart_dma.rx_dma_channel,
1152 OMAP_DMA_DATA_TYPE_S8,
1153 up->uart_dma.rx_buf_size, 1,
1154 OMAP_DMA_SYNC_ELEMENT,
1155 up->uart_dma.uart_dma_rx, 0);
1156 }
1157 up->uart_dma.prev_rx_dma_pos = up->uart_dma.rx_buf_dma_phys;
1158 /* FIXME: Cache maintenance needed here? */
1159 omap_start_dma(up->uart_dma.rx_dma_channel);
1160 mod_timer(&up->uart_dma.rx_timer, jiffies +
1161 usecs_to_jiffies(up->uart_dma.rx_timeout));
1162 up->uart_dma.rx_dma_used = true;
1163 return ret;
1164}
1165
1166static void serial_omap_continue_tx(struct uart_omap_port *up)
1167{
1168 struct circ_buf *xmit = &up->port.state->xmit;
1169 unsigned int start = up->uart_dma.tx_buf_dma_phys
1170 + (xmit->tail & (UART_XMIT_SIZE - 1));
1171
1172 if (uart_circ_empty(xmit))
1173 return;
1174
1175 up->uart_dma.tx_buf_size = uart_circ_chars_pending(xmit);
1176 /*
1177 * It is a circular buffer. See if the buffer has wounded back.
1178 * If yes it will have to be transferred in two separate dma
1179 * transfers
1180 */
1181 if (start + up->uart_dma.tx_buf_size >=
1182 up->uart_dma.tx_buf_dma_phys + UART_XMIT_SIZE)
1183 up->uart_dma.tx_buf_size =
1184 (up->uart_dma.tx_buf_dma_phys + UART_XMIT_SIZE) - start;
1185 omap_set_dma_dest_params(up->uart_dma.tx_dma_channel, 0,
1186 OMAP_DMA_AMODE_CONSTANT,
1187 up->uart_dma.uart_base, 0, 0);
1188 omap_set_dma_src_params(up->uart_dma.tx_dma_channel, 0,
1189 OMAP_DMA_AMODE_POST_INC, start, 0, 0);
1190 omap_set_dma_transfer_params(up->uart_dma.tx_dma_channel,
1191 OMAP_DMA_DATA_TYPE_S8,
1192 up->uart_dma.tx_buf_size, 1,
1193 OMAP_DMA_SYNC_ELEMENT,
1194 up->uart_dma.uart_dma_tx, 0);
1195 /* FIXME: Cache maintenance needed here? */
1196 omap_start_dma(up->uart_dma.tx_dma_channel);
1197}
1198
1199static void uart_tx_dma_callback(int lch, u16 ch_status, void *data)
1200{
1201 struct uart_omap_port *up = (struct uart_omap_port *)data;
1202 struct circ_buf *xmit = &up->port.state->xmit;
1203
1204 xmit->tail = (xmit->tail + up->uart_dma.tx_buf_size) & \
1205 (UART_XMIT_SIZE - 1);
1206 up->port.icount.tx += up->uart_dma.tx_buf_size;
1207
1208 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
1209 uart_write_wakeup(&up->port);
1210
1211 if (uart_circ_empty(xmit)) {
1212 spin_lock(&(up->uart_dma.tx_lock));
1213 serial_omap_stop_tx(&up->port);
1214 up->uart_dma.tx_dma_used = false;
1215 spin_unlock(&(up->uart_dma.tx_lock));
1216 } else {
1217 omap_stop_dma(up->uart_dma.tx_dma_channel);
1218 serial_omap_continue_tx(up);
1219 }
1220 up->port_activity = jiffies;
1221 return;
1222}
1223
1224static int serial_omap_probe(struct platform_device *pdev)
1225{
1226 struct uart_omap_port *up;
1227 struct resource *mem, *irq, *dma_tx, *dma_rx;
1228 struct omap_uart_port_info *omap_up_info = pdev->dev.platform_data;
1229 int ret = -ENOSPC;
1230
1231 mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1232 if (!mem) {
1233 dev_err(&pdev->dev, "no mem resource?\n");
1234 return -ENODEV;
1235 }
1236
1237 irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
1238 if (!irq) {
1239 dev_err(&pdev->dev, "no irq resource?\n");
1240 return -ENODEV;
1241 }
1242
1243 if (!request_mem_region(mem->start, resource_size(mem),
1244 pdev->dev.driver->name)) {
1245 dev_err(&pdev->dev, "memory region already claimed\n");
1246 return -EBUSY;
1247 }
1248
1249 dma_rx = platform_get_resource_byname(pdev, IORESOURCE_DMA, "rx");
1250 if (!dma_rx) {
1251 ret = -EINVAL;
1252 goto err;
1253 }
1254
1255 dma_tx = platform_get_resource_byname(pdev, IORESOURCE_DMA, "tx");
1256 if (!dma_tx) {
1257 ret = -EINVAL;
1258 goto err;
1259 }
1260
1261 up = kzalloc(sizeof(*up), GFP_KERNEL);
1262 if (up == NULL) {
1263 ret = -ENOMEM;
1264 goto do_release_region;
1265 }
1266 sprintf(up->name, "OMAP UART%d", pdev->id);
1267 up->pdev = pdev;
1268 up->port.dev = &pdev->dev;
1269 up->port.type = PORT_OMAP;
1270 up->port.iotype = UPIO_MEM;
1271 up->port.irq = irq->start;
1272
1273 up->port.regshift = 2;
1274 up->port.fifosize = 64;
1275 up->port.ops = &serial_omap_pops;
1276 up->port.line = pdev->id;
1277
1278 up->port.membase = omap_up_info->membase;
1279 up->port.mapbase = omap_up_info->mapbase;
1280 up->port.flags = omap_up_info->flags;
1281 up->port.irqflags = omap_up_info->irqflags;
1282 up->port.uartclk = omap_up_info->uartclk;
1283 up->uart_dma.uart_base = mem->start;
1284
1285 if (omap_up_info->dma_enabled) {
1286 up->uart_dma.uart_dma_tx = dma_tx->start;
1287 up->uart_dma.uart_dma_rx = dma_rx->start;
1288 up->use_dma = 1;
1289 up->uart_dma.rx_buf_size = 4096;
1290 up->uart_dma.rx_timeout = 2;
1291 spin_lock_init(&(up->uart_dma.tx_lock));
1292 spin_lock_init(&(up->uart_dma.rx_lock));
1293 up->uart_dma.tx_dma_channel = OMAP_UART_DMA_CH_FREE;
1294 up->uart_dma.rx_dma_channel = OMAP_UART_DMA_CH_FREE;
1295 }
1296
1297 ui[pdev->id] = up;
1298 serial_omap_add_console_port(up);
1299
1300 ret = uart_add_one_port(&serial_omap_reg, &up->port);
1301 if (ret != 0)
1302 goto do_release_region;
1303
1304 platform_set_drvdata(pdev, up);
1305 return 0;
1306err:
1307 dev_err(&pdev->dev, "[UART%d]: failure [%s]: %d\n",
1308 pdev->id, __func__, ret);
1309do_release_region:
1310 release_mem_region(mem->start, resource_size(mem));
1311 return ret;
1312}
1313
1314static int serial_omap_remove(struct platform_device *dev)
1315{
1316 struct uart_omap_port *up = platform_get_drvdata(dev);
1317
1318 platform_set_drvdata(dev, NULL);
1319 if (up) {
1320 uart_remove_one_port(&serial_omap_reg, &up->port);
1321 kfree(up);
1322 }
1323 return 0;
1324}
1325
1326static struct platform_driver serial_omap_driver = {
1327 .probe = serial_omap_probe,
1328 .remove = serial_omap_remove,
1329
1330 .suspend = serial_omap_suspend,
1331 .resume = serial_omap_resume,
1332 .driver = {
1333 .name = DRIVER_NAME,
1334 },
1335};
1336
1337static int __init serial_omap_init(void)
1338{
1339 int ret;
1340
1341 ret = uart_register_driver(&serial_omap_reg);
1342 if (ret != 0)
1343 return ret;
1344 ret = platform_driver_register(&serial_omap_driver);
1345 if (ret != 0)
1346 uart_unregister_driver(&serial_omap_reg);
1347 return ret;
1348}
1349
1350static void __exit serial_omap_exit(void)
1351{
1352 platform_driver_unregister(&serial_omap_driver);
1353 uart_unregister_driver(&serial_omap_reg);
1354}
1355
1356module_init(serial_omap_init);
1357module_exit(serial_omap_exit);
1358
1359MODULE_DESCRIPTION("OMAP High Speed UART driver");
1360MODULE_LICENSE("GPL");
1361MODULE_AUTHOR("Texas Instruments Inc");
1/*
2 * Driver for OMAP-UART controller.
3 * Based on drivers/serial/8250.c
4 *
5 * Copyright (C) 2010 Texas Instruments.
6 *
7 * Authors:
8 * Govindraj R <govindraj.raja@ti.com>
9 * Thara Gopinath <thara@ti.com>
10 *
11 * This program is free software; you can redistribute it and/or modify
12 * it under the terms of the GNU General Public License as published by
13 * the Free Software Foundation; either version 2 of the License, or
14 * (at your option) any later version.
15 *
16 * Note: This driver is made separate from 8250 driver as we cannot
17 * over load 8250 driver with omap platform specific configuration for
18 * features like DMA, it makes easier to implement features like DMA and
19 * hardware flow control and software flow control configuration with
20 * this driver as required for the omap-platform.
21 */
22
23#if defined(CONFIG_SERIAL_OMAP_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
24#define SUPPORT_SYSRQ
25#endif
26
27#include <linux/module.h>
28#include <linux/init.h>
29#include <linux/console.h>
30#include <linux/serial_reg.h>
31#include <linux/delay.h>
32#include <linux/slab.h>
33#include <linux/tty.h>
34#include <linux/tty_flip.h>
35#include <linux/platform_device.h>
36#include <linux/io.h>
37#include <linux/clk.h>
38#include <linux/serial_core.h>
39#include <linux/irq.h>
40#include <linux/pm_runtime.h>
41#include <linux/pm_wakeirq.h>
42#include <linux/of.h>
43#include <linux/of_irq.h>
44#include <linux/gpio.h>
45#include <linux/of_gpio.h>
46#include <linux/platform_data/serial-omap.h>
47
48#include <dt-bindings/gpio/gpio.h>
49
50#define OMAP_MAX_HSUART_PORTS 10
51
52#define UART_BUILD_REVISION(x, y) (((x) << 8) | (y))
53
54#define OMAP_UART_REV_42 0x0402
55#define OMAP_UART_REV_46 0x0406
56#define OMAP_UART_REV_52 0x0502
57#define OMAP_UART_REV_63 0x0603
58
59#define OMAP_UART_TX_WAKEUP_EN BIT(7)
60
61/* Feature flags */
62#define OMAP_UART_WER_HAS_TX_WAKEUP BIT(0)
63
64#define UART_ERRATA_i202_MDR1_ACCESS BIT(0)
65#define UART_ERRATA_i291_DMA_FORCEIDLE BIT(1)
66
67#define DEFAULT_CLK_SPEED 48000000 /* 48Mhz */
68
69/* SCR register bitmasks */
70#define OMAP_UART_SCR_RX_TRIG_GRANU1_MASK (1 << 7)
71#define OMAP_UART_SCR_TX_TRIG_GRANU1_MASK (1 << 6)
72#define OMAP_UART_SCR_TX_EMPTY (1 << 3)
73
74/* FCR register bitmasks */
75#define OMAP_UART_FCR_RX_FIFO_TRIG_MASK (0x3 << 6)
76#define OMAP_UART_FCR_TX_FIFO_TRIG_MASK (0x3 << 4)
77
78/* MVR register bitmasks */
79#define OMAP_UART_MVR_SCHEME_SHIFT 30
80
81#define OMAP_UART_LEGACY_MVR_MAJ_MASK 0xf0
82#define OMAP_UART_LEGACY_MVR_MAJ_SHIFT 4
83#define OMAP_UART_LEGACY_MVR_MIN_MASK 0x0f
84
85#define OMAP_UART_MVR_MAJ_MASK 0x700
86#define OMAP_UART_MVR_MAJ_SHIFT 8
87#define OMAP_UART_MVR_MIN_MASK 0x3f
88
89#define OMAP_UART_DMA_CH_FREE -1
90
91#define MSR_SAVE_FLAGS UART_MSR_ANY_DELTA
92#define OMAP_MODE13X_SPEED 230400
93
94/* WER = 0x7F
95 * Enable module level wakeup in WER reg
96 */
97#define OMAP_UART_WER_MOD_WKUP 0x7F
98
99/* Enable XON/XOFF flow control on output */
100#define OMAP_UART_SW_TX 0x08
101
102/* Enable XON/XOFF flow control on input */
103#define OMAP_UART_SW_RX 0x02
104
105#define OMAP_UART_SW_CLR 0xF0
106
107#define OMAP_UART_TCR_TRIG 0x0F
108
109struct uart_omap_dma {
110 u8 uart_dma_tx;
111 u8 uart_dma_rx;
112 int rx_dma_channel;
113 int tx_dma_channel;
114 dma_addr_t rx_buf_dma_phys;
115 dma_addr_t tx_buf_dma_phys;
116 unsigned int uart_base;
117 /*
118 * Buffer for rx dma. It is not required for tx because the buffer
119 * comes from port structure.
120 */
121 unsigned char *rx_buf;
122 unsigned int prev_rx_dma_pos;
123 int tx_buf_size;
124 int tx_dma_used;
125 int rx_dma_used;
126 spinlock_t tx_lock;
127 spinlock_t rx_lock;
128 /* timer to poll activity on rx dma */
129 struct timer_list rx_timer;
130 unsigned int rx_buf_size;
131 unsigned int rx_poll_rate;
132 unsigned int rx_timeout;
133};
134
135struct uart_omap_port {
136 struct uart_port port;
137 struct uart_omap_dma uart_dma;
138 struct device *dev;
139 int wakeirq;
140
141 unsigned char ier;
142 unsigned char lcr;
143 unsigned char mcr;
144 unsigned char fcr;
145 unsigned char efr;
146 unsigned char dll;
147 unsigned char dlh;
148 unsigned char mdr1;
149 unsigned char scr;
150 unsigned char wer;
151
152 int use_dma;
153 /*
154 * Some bits in registers are cleared on a read, so they must
155 * be saved whenever the register is read, but the bits will not
156 * be immediately processed.
157 */
158 unsigned int lsr_break_flag;
159 unsigned char msr_saved_flags;
160 char name[20];
161 unsigned long port_activity;
162 int context_loss_cnt;
163 u32 errata;
164 u32 features;
165
166 int rts_gpio;
167
168 struct pm_qos_request pm_qos_request;
169 u32 latency;
170 u32 calc_latency;
171 struct work_struct qos_work;
172 bool is_suspending;
173};
174
175#define to_uart_omap_port(p) ((container_of((p), struct uart_omap_port, port)))
176
177static struct uart_omap_port *ui[OMAP_MAX_HSUART_PORTS];
178
179/* Forward declaration of functions */
180static void serial_omap_mdr1_errataset(struct uart_omap_port *up, u8 mdr1);
181
182static inline unsigned int serial_in(struct uart_omap_port *up, int offset)
183{
184 offset <<= up->port.regshift;
185 return readw(up->port.membase + offset);
186}
187
188static inline void serial_out(struct uart_omap_port *up, int offset, int value)
189{
190 offset <<= up->port.regshift;
191 writew(value, up->port.membase + offset);
192}
193
194static inline void serial_omap_clear_fifos(struct uart_omap_port *up)
195{
196 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
197 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
198 UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
199 serial_out(up, UART_FCR, 0);
200}
201
202#ifdef CONFIG_PM
203static int serial_omap_get_context_loss_count(struct uart_omap_port *up)
204{
205 struct omap_uart_port_info *pdata = dev_get_platdata(up->dev);
206
207 if (!pdata || !pdata->get_context_loss_count)
208 return -EINVAL;
209
210 return pdata->get_context_loss_count(up->dev);
211}
212
213/* REVISIT: Remove this when omap3 boots in device tree only mode */
214static void serial_omap_enable_wakeup(struct uart_omap_port *up, bool enable)
215{
216 struct omap_uart_port_info *pdata = dev_get_platdata(up->dev);
217
218 if (!pdata || !pdata->enable_wakeup)
219 return;
220
221 pdata->enable_wakeup(up->dev, enable);
222}
223#endif /* CONFIG_PM */
224
225/*
226 * Calculate the absolute difference between the desired and actual baud
227 * rate for the given mode.
228 */
229static inline int calculate_baud_abs_diff(struct uart_port *port,
230 unsigned int baud, unsigned int mode)
231{
232 unsigned int n = port->uartclk / (mode * baud);
233 int abs_diff;
234
235 if (n == 0)
236 n = 1;
237
238 abs_diff = baud - (port->uartclk / (mode * n));
239 if (abs_diff < 0)
240 abs_diff = -abs_diff;
241
242 return abs_diff;
243}
244
245/*
246 * serial_omap_baud_is_mode16 - check if baud rate is MODE16X
247 * @port: uart port info
248 * @baud: baudrate for which mode needs to be determined
249 *
250 * Returns true if baud rate is MODE16X and false if MODE13X
251 * Original table in OMAP TRM named "UART Mode Baud Rates, Divisor Values,
252 * and Error Rates" determines modes not for all common baud rates.
253 * E.g. for 1000000 baud rate mode must be 16x, but according to that
254 * table it's determined as 13x.
255 */
256static bool
257serial_omap_baud_is_mode16(struct uart_port *port, unsigned int baud)
258{
259 int abs_diff_13 = calculate_baud_abs_diff(port, baud, 13);
260 int abs_diff_16 = calculate_baud_abs_diff(port, baud, 16);
261
262 return (abs_diff_13 >= abs_diff_16);
263}
264
265/*
266 * serial_omap_get_divisor - calculate divisor value
267 * @port: uart port info
268 * @baud: baudrate for which divisor needs to be calculated.
269 */
270static unsigned int
271serial_omap_get_divisor(struct uart_port *port, unsigned int baud)
272{
273 unsigned int mode;
274
275 if (!serial_omap_baud_is_mode16(port, baud))
276 mode = 13;
277 else
278 mode = 16;
279 return port->uartclk/(mode * baud);
280}
281
282static void serial_omap_enable_ms(struct uart_port *port)
283{
284 struct uart_omap_port *up = to_uart_omap_port(port);
285
286 dev_dbg(up->port.dev, "serial_omap_enable_ms+%d\n", up->port.line);
287
288 pm_runtime_get_sync(up->dev);
289 up->ier |= UART_IER_MSI;
290 serial_out(up, UART_IER, up->ier);
291 pm_runtime_mark_last_busy(up->dev);
292 pm_runtime_put_autosuspend(up->dev);
293}
294
295static void serial_omap_stop_tx(struct uart_port *port)
296{
297 struct uart_omap_port *up = to_uart_omap_port(port);
298 int res;
299
300 pm_runtime_get_sync(up->dev);
301
302 /* Handle RS-485 */
303 if (port->rs485.flags & SER_RS485_ENABLED) {
304 if (up->scr & OMAP_UART_SCR_TX_EMPTY) {
305 /* THR interrupt is fired when both TX FIFO and TX
306 * shift register are empty. This means there's nothing
307 * left to transmit now, so make sure the THR interrupt
308 * is fired when TX FIFO is below the trigger level,
309 * disable THR interrupts and toggle the RS-485 GPIO
310 * data direction pin if needed.
311 */
312 up->scr &= ~OMAP_UART_SCR_TX_EMPTY;
313 serial_out(up, UART_OMAP_SCR, up->scr);
314 res = (port->rs485.flags & SER_RS485_RTS_AFTER_SEND) ?
315 1 : 0;
316 if (gpio_get_value(up->rts_gpio) != res) {
317 if (port->rs485.delay_rts_after_send > 0)
318 mdelay(
319 port->rs485.delay_rts_after_send);
320 gpio_set_value(up->rts_gpio, res);
321 }
322 } else {
323 /* We're asked to stop, but there's still stuff in the
324 * UART FIFO, so make sure the THR interrupt is fired
325 * when both TX FIFO and TX shift register are empty.
326 * The next THR interrupt (if no transmission is started
327 * in the meantime) will indicate the end of a
328 * transmission. Therefore we _don't_ disable THR
329 * interrupts in this situation.
330 */
331 up->scr |= OMAP_UART_SCR_TX_EMPTY;
332 serial_out(up, UART_OMAP_SCR, up->scr);
333 return;
334 }
335 }
336
337 if (up->ier & UART_IER_THRI) {
338 up->ier &= ~UART_IER_THRI;
339 serial_out(up, UART_IER, up->ier);
340 }
341
342 if ((port->rs485.flags & SER_RS485_ENABLED) &&
343 !(port->rs485.flags & SER_RS485_RX_DURING_TX)) {
344 /*
345 * Empty the RX FIFO, we are not interested in anything
346 * received during the half-duplex transmission.
347 */
348 serial_out(up, UART_FCR, up->fcr | UART_FCR_CLEAR_RCVR);
349 /* Re-enable RX interrupts */
350 up->ier |= UART_IER_RLSI | UART_IER_RDI;
351 up->port.read_status_mask |= UART_LSR_DR;
352 serial_out(up, UART_IER, up->ier);
353 }
354
355 pm_runtime_mark_last_busy(up->dev);
356 pm_runtime_put_autosuspend(up->dev);
357}
358
359static void serial_omap_stop_rx(struct uart_port *port)
360{
361 struct uart_omap_port *up = to_uart_omap_port(port);
362
363 pm_runtime_get_sync(up->dev);
364 up->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
365 up->port.read_status_mask &= ~UART_LSR_DR;
366 serial_out(up, UART_IER, up->ier);
367 pm_runtime_mark_last_busy(up->dev);
368 pm_runtime_put_autosuspend(up->dev);
369}
370
371static void transmit_chars(struct uart_omap_port *up, unsigned int lsr)
372{
373 struct circ_buf *xmit = &up->port.state->xmit;
374 int count;
375
376 if (up->port.x_char) {
377 serial_out(up, UART_TX, up->port.x_char);
378 up->port.icount.tx++;
379 up->port.x_char = 0;
380 return;
381 }
382 if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
383 serial_omap_stop_tx(&up->port);
384 return;
385 }
386 count = up->port.fifosize / 4;
387 do {
388 serial_out(up, UART_TX, xmit->buf[xmit->tail]);
389 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
390 up->port.icount.tx++;
391 if (uart_circ_empty(xmit))
392 break;
393 } while (--count > 0);
394
395 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
396 uart_write_wakeup(&up->port);
397
398 if (uart_circ_empty(xmit))
399 serial_omap_stop_tx(&up->port);
400}
401
402static inline void serial_omap_enable_ier_thri(struct uart_omap_port *up)
403{
404 if (!(up->ier & UART_IER_THRI)) {
405 up->ier |= UART_IER_THRI;
406 serial_out(up, UART_IER, up->ier);
407 }
408}
409
410static void serial_omap_start_tx(struct uart_port *port)
411{
412 struct uart_omap_port *up = to_uart_omap_port(port);
413 int res;
414
415 pm_runtime_get_sync(up->dev);
416
417 /* Handle RS-485 */
418 if (port->rs485.flags & SER_RS485_ENABLED) {
419 /* Fire THR interrupts when FIFO is below trigger level */
420 up->scr &= ~OMAP_UART_SCR_TX_EMPTY;
421 serial_out(up, UART_OMAP_SCR, up->scr);
422
423 /* if rts not already enabled */
424 res = (port->rs485.flags & SER_RS485_RTS_ON_SEND) ? 1 : 0;
425 if (gpio_get_value(up->rts_gpio) != res) {
426 gpio_set_value(up->rts_gpio, res);
427 if (port->rs485.delay_rts_before_send > 0)
428 mdelay(port->rs485.delay_rts_before_send);
429 }
430 }
431
432 if ((port->rs485.flags & SER_RS485_ENABLED) &&
433 !(port->rs485.flags & SER_RS485_RX_DURING_TX))
434 serial_omap_stop_rx(port);
435
436 serial_omap_enable_ier_thri(up);
437 pm_runtime_mark_last_busy(up->dev);
438 pm_runtime_put_autosuspend(up->dev);
439}
440
441static void serial_omap_throttle(struct uart_port *port)
442{
443 struct uart_omap_port *up = to_uart_omap_port(port);
444 unsigned long flags;
445
446 pm_runtime_get_sync(up->dev);
447 spin_lock_irqsave(&up->port.lock, flags);
448 up->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
449 serial_out(up, UART_IER, up->ier);
450 spin_unlock_irqrestore(&up->port.lock, flags);
451 pm_runtime_mark_last_busy(up->dev);
452 pm_runtime_put_autosuspend(up->dev);
453}
454
455static void serial_omap_unthrottle(struct uart_port *port)
456{
457 struct uart_omap_port *up = to_uart_omap_port(port);
458 unsigned long flags;
459
460 pm_runtime_get_sync(up->dev);
461 spin_lock_irqsave(&up->port.lock, flags);
462 up->ier |= UART_IER_RLSI | UART_IER_RDI;
463 serial_out(up, UART_IER, up->ier);
464 spin_unlock_irqrestore(&up->port.lock, flags);
465 pm_runtime_mark_last_busy(up->dev);
466 pm_runtime_put_autosuspend(up->dev);
467}
468
469static unsigned int check_modem_status(struct uart_omap_port *up)
470{
471 unsigned int status;
472
473 status = serial_in(up, UART_MSR);
474 status |= up->msr_saved_flags;
475 up->msr_saved_flags = 0;
476 if ((status & UART_MSR_ANY_DELTA) == 0)
477 return status;
478
479 if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI &&
480 up->port.state != NULL) {
481 if (status & UART_MSR_TERI)
482 up->port.icount.rng++;
483 if (status & UART_MSR_DDSR)
484 up->port.icount.dsr++;
485 if (status & UART_MSR_DDCD)
486 uart_handle_dcd_change
487 (&up->port, status & UART_MSR_DCD);
488 if (status & UART_MSR_DCTS)
489 uart_handle_cts_change
490 (&up->port, status & UART_MSR_CTS);
491 wake_up_interruptible(&up->port.state->port.delta_msr_wait);
492 }
493
494 return status;
495}
496
497static void serial_omap_rlsi(struct uart_omap_port *up, unsigned int lsr)
498{
499 unsigned int flag;
500 unsigned char ch = 0;
501
502 if (likely(lsr & UART_LSR_DR))
503 ch = serial_in(up, UART_RX);
504
505 up->port.icount.rx++;
506 flag = TTY_NORMAL;
507
508 if (lsr & UART_LSR_BI) {
509 flag = TTY_BREAK;
510 lsr &= ~(UART_LSR_FE | UART_LSR_PE);
511 up->port.icount.brk++;
512 /*
513 * We do the SysRQ and SAK checking
514 * here because otherwise the break
515 * may get masked by ignore_status_mask
516 * or read_status_mask.
517 */
518 if (uart_handle_break(&up->port))
519 return;
520
521 }
522
523 if (lsr & UART_LSR_PE) {
524 flag = TTY_PARITY;
525 up->port.icount.parity++;
526 }
527
528 if (lsr & UART_LSR_FE) {
529 flag = TTY_FRAME;
530 up->port.icount.frame++;
531 }
532
533 if (lsr & UART_LSR_OE)
534 up->port.icount.overrun++;
535
536#ifdef CONFIG_SERIAL_OMAP_CONSOLE
537 if (up->port.line == up->port.cons->index) {
538 /* Recover the break flag from console xmit */
539 lsr |= up->lsr_break_flag;
540 }
541#endif
542 uart_insert_char(&up->port, lsr, UART_LSR_OE, 0, flag);
543}
544
545static void serial_omap_rdi(struct uart_omap_port *up, unsigned int lsr)
546{
547 unsigned char ch = 0;
548 unsigned int flag;
549
550 if (!(lsr & UART_LSR_DR))
551 return;
552
553 ch = serial_in(up, UART_RX);
554 flag = TTY_NORMAL;
555 up->port.icount.rx++;
556
557 if (uart_handle_sysrq_char(&up->port, ch))
558 return;
559
560 uart_insert_char(&up->port, lsr, UART_LSR_OE, ch, flag);
561}
562
563/**
564 * serial_omap_irq() - This handles the interrupt from one port
565 * @irq: uart port irq number
566 * @dev_id: uart port info
567 */
568static irqreturn_t serial_omap_irq(int irq, void *dev_id)
569{
570 struct uart_omap_port *up = dev_id;
571 unsigned int iir, lsr;
572 unsigned int type;
573 irqreturn_t ret = IRQ_NONE;
574 int max_count = 256;
575
576 spin_lock(&up->port.lock);
577 pm_runtime_get_sync(up->dev);
578
579 do {
580 iir = serial_in(up, UART_IIR);
581 if (iir & UART_IIR_NO_INT)
582 break;
583
584 ret = IRQ_HANDLED;
585 lsr = serial_in(up, UART_LSR);
586
587 /* extract IRQ type from IIR register */
588 type = iir & 0x3e;
589
590 switch (type) {
591 case UART_IIR_MSI:
592 check_modem_status(up);
593 break;
594 case UART_IIR_THRI:
595 transmit_chars(up, lsr);
596 break;
597 case UART_IIR_RX_TIMEOUT:
598 /* FALLTHROUGH */
599 case UART_IIR_RDI:
600 serial_omap_rdi(up, lsr);
601 break;
602 case UART_IIR_RLSI:
603 serial_omap_rlsi(up, lsr);
604 break;
605 case UART_IIR_CTS_RTS_DSR:
606 /* simply try again */
607 break;
608 case UART_IIR_XOFF:
609 /* FALLTHROUGH */
610 default:
611 break;
612 }
613 } while (!(iir & UART_IIR_NO_INT) && max_count--);
614
615 spin_unlock(&up->port.lock);
616
617 tty_flip_buffer_push(&up->port.state->port);
618
619 pm_runtime_mark_last_busy(up->dev);
620 pm_runtime_put_autosuspend(up->dev);
621 up->port_activity = jiffies;
622
623 return ret;
624}
625
626static unsigned int serial_omap_tx_empty(struct uart_port *port)
627{
628 struct uart_omap_port *up = to_uart_omap_port(port);
629 unsigned long flags = 0;
630 unsigned int ret = 0;
631
632 pm_runtime_get_sync(up->dev);
633 dev_dbg(up->port.dev, "serial_omap_tx_empty+%d\n", up->port.line);
634 spin_lock_irqsave(&up->port.lock, flags);
635 ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
636 spin_unlock_irqrestore(&up->port.lock, flags);
637 pm_runtime_mark_last_busy(up->dev);
638 pm_runtime_put_autosuspend(up->dev);
639 return ret;
640}
641
642static unsigned int serial_omap_get_mctrl(struct uart_port *port)
643{
644 struct uart_omap_port *up = to_uart_omap_port(port);
645 unsigned int status;
646 unsigned int ret = 0;
647
648 pm_runtime_get_sync(up->dev);
649 status = check_modem_status(up);
650 pm_runtime_mark_last_busy(up->dev);
651 pm_runtime_put_autosuspend(up->dev);
652
653 dev_dbg(up->port.dev, "serial_omap_get_mctrl+%d\n", up->port.line);
654
655 if (status & UART_MSR_DCD)
656 ret |= TIOCM_CAR;
657 if (status & UART_MSR_RI)
658 ret |= TIOCM_RNG;
659 if (status & UART_MSR_DSR)
660 ret |= TIOCM_DSR;
661 if (status & UART_MSR_CTS)
662 ret |= TIOCM_CTS;
663 return ret;
664}
665
666static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl)
667{
668 struct uart_omap_port *up = to_uart_omap_port(port);
669 unsigned char mcr = 0, old_mcr, lcr;
670
671 dev_dbg(up->port.dev, "serial_omap_set_mctrl+%d\n", up->port.line);
672 if (mctrl & TIOCM_RTS)
673 mcr |= UART_MCR_RTS;
674 if (mctrl & TIOCM_DTR)
675 mcr |= UART_MCR_DTR;
676 if (mctrl & TIOCM_OUT1)
677 mcr |= UART_MCR_OUT1;
678 if (mctrl & TIOCM_OUT2)
679 mcr |= UART_MCR_OUT2;
680 if (mctrl & TIOCM_LOOP)
681 mcr |= UART_MCR_LOOP;
682
683 pm_runtime_get_sync(up->dev);
684 old_mcr = serial_in(up, UART_MCR);
685 old_mcr &= ~(UART_MCR_LOOP | UART_MCR_OUT2 | UART_MCR_OUT1 |
686 UART_MCR_DTR | UART_MCR_RTS);
687 up->mcr = old_mcr | mcr;
688 serial_out(up, UART_MCR, up->mcr);
689
690 /* Turn off autoRTS if RTS is lowered; restore autoRTS if RTS raised */
691 lcr = serial_in(up, UART_LCR);
692 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
693 if ((mctrl & TIOCM_RTS) && (port->status & UPSTAT_AUTORTS))
694 up->efr |= UART_EFR_RTS;
695 else
696 up->efr &= UART_EFR_RTS;
697 serial_out(up, UART_EFR, up->efr);
698 serial_out(up, UART_LCR, lcr);
699
700 pm_runtime_mark_last_busy(up->dev);
701 pm_runtime_put_autosuspend(up->dev);
702}
703
704static void serial_omap_break_ctl(struct uart_port *port, int break_state)
705{
706 struct uart_omap_port *up = to_uart_omap_port(port);
707 unsigned long flags = 0;
708
709 dev_dbg(up->port.dev, "serial_omap_break_ctl+%d\n", up->port.line);
710 pm_runtime_get_sync(up->dev);
711 spin_lock_irqsave(&up->port.lock, flags);
712 if (break_state == -1)
713 up->lcr |= UART_LCR_SBC;
714 else
715 up->lcr &= ~UART_LCR_SBC;
716 serial_out(up, UART_LCR, up->lcr);
717 spin_unlock_irqrestore(&up->port.lock, flags);
718 pm_runtime_mark_last_busy(up->dev);
719 pm_runtime_put_autosuspend(up->dev);
720}
721
722static int serial_omap_startup(struct uart_port *port)
723{
724 struct uart_omap_port *up = to_uart_omap_port(port);
725 unsigned long flags = 0;
726 int retval;
727
728 /*
729 * Allocate the IRQ
730 */
731 retval = request_irq(up->port.irq, serial_omap_irq, up->port.irqflags,
732 up->name, up);
733 if (retval)
734 return retval;
735
736 /* Optional wake-up IRQ */
737 if (up->wakeirq) {
738 retval = dev_pm_set_dedicated_wake_irq(up->dev, up->wakeirq);
739 if (retval) {
740 free_irq(up->port.irq, up);
741 return retval;
742 }
743 }
744
745 dev_dbg(up->port.dev, "serial_omap_startup+%d\n", up->port.line);
746
747 pm_runtime_get_sync(up->dev);
748 /*
749 * Clear the FIFO buffers and disable them.
750 * (they will be reenabled in set_termios())
751 */
752 serial_omap_clear_fifos(up);
753
754 /*
755 * Clear the interrupt registers.
756 */
757 (void) serial_in(up, UART_LSR);
758 if (serial_in(up, UART_LSR) & UART_LSR_DR)
759 (void) serial_in(up, UART_RX);
760 (void) serial_in(up, UART_IIR);
761 (void) serial_in(up, UART_MSR);
762
763 /*
764 * Now, initialize the UART
765 */
766 serial_out(up, UART_LCR, UART_LCR_WLEN8);
767 spin_lock_irqsave(&up->port.lock, flags);
768 /*
769 * Most PC uarts need OUT2 raised to enable interrupts.
770 */
771 up->port.mctrl |= TIOCM_OUT2;
772 serial_omap_set_mctrl(&up->port, up->port.mctrl);
773 spin_unlock_irqrestore(&up->port.lock, flags);
774
775 up->msr_saved_flags = 0;
776 /*
777 * Finally, enable interrupts. Note: Modem status interrupts
778 * are set via set_termios(), which will be occurring imminently
779 * anyway, so we don't enable them here.
780 */
781 up->ier = UART_IER_RLSI | UART_IER_RDI;
782 serial_out(up, UART_IER, up->ier);
783
784 /* Enable module level wake up */
785 up->wer = OMAP_UART_WER_MOD_WKUP;
786 if (up->features & OMAP_UART_WER_HAS_TX_WAKEUP)
787 up->wer |= OMAP_UART_TX_WAKEUP_EN;
788
789 serial_out(up, UART_OMAP_WER, up->wer);
790
791 pm_runtime_mark_last_busy(up->dev);
792 pm_runtime_put_autosuspend(up->dev);
793 up->port_activity = jiffies;
794 return 0;
795}
796
797static void serial_omap_shutdown(struct uart_port *port)
798{
799 struct uart_omap_port *up = to_uart_omap_port(port);
800 unsigned long flags = 0;
801
802 dev_dbg(up->port.dev, "serial_omap_shutdown+%d\n", up->port.line);
803
804 pm_runtime_get_sync(up->dev);
805 /*
806 * Disable interrupts from this port
807 */
808 up->ier = 0;
809 serial_out(up, UART_IER, 0);
810
811 spin_lock_irqsave(&up->port.lock, flags);
812 up->port.mctrl &= ~TIOCM_OUT2;
813 serial_omap_set_mctrl(&up->port, up->port.mctrl);
814 spin_unlock_irqrestore(&up->port.lock, flags);
815
816 /*
817 * Disable break condition and FIFOs
818 */
819 serial_out(up, UART_LCR, serial_in(up, UART_LCR) & ~UART_LCR_SBC);
820 serial_omap_clear_fifos(up);
821
822 /*
823 * Read data port to reset things, and then free the irq
824 */
825 if (serial_in(up, UART_LSR) & UART_LSR_DR)
826 (void) serial_in(up, UART_RX);
827
828 pm_runtime_mark_last_busy(up->dev);
829 pm_runtime_put_autosuspend(up->dev);
830 free_irq(up->port.irq, up);
831 dev_pm_clear_wake_irq(up->dev);
832}
833
834static void serial_omap_uart_qos_work(struct work_struct *work)
835{
836 struct uart_omap_port *up = container_of(work, struct uart_omap_port,
837 qos_work);
838
839 pm_qos_update_request(&up->pm_qos_request, up->latency);
840}
841
842static void
843serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
844 struct ktermios *old)
845{
846 struct uart_omap_port *up = to_uart_omap_port(port);
847 unsigned char cval = 0;
848 unsigned long flags = 0;
849 unsigned int baud, quot;
850
851 switch (termios->c_cflag & CSIZE) {
852 case CS5:
853 cval = UART_LCR_WLEN5;
854 break;
855 case CS6:
856 cval = UART_LCR_WLEN6;
857 break;
858 case CS7:
859 cval = UART_LCR_WLEN7;
860 break;
861 default:
862 case CS8:
863 cval = UART_LCR_WLEN8;
864 break;
865 }
866
867 if (termios->c_cflag & CSTOPB)
868 cval |= UART_LCR_STOP;
869 if (termios->c_cflag & PARENB)
870 cval |= UART_LCR_PARITY;
871 if (!(termios->c_cflag & PARODD))
872 cval |= UART_LCR_EPAR;
873 if (termios->c_cflag & CMSPAR)
874 cval |= UART_LCR_SPAR;
875
876 /*
877 * Ask the core to calculate the divisor for us.
878 */
879
880 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/13);
881 quot = serial_omap_get_divisor(port, baud);
882
883 /* calculate wakeup latency constraint */
884 up->calc_latency = (USEC_PER_SEC * up->port.fifosize) / (baud / 8);
885 up->latency = up->calc_latency;
886 schedule_work(&up->qos_work);
887
888 up->dll = quot & 0xff;
889 up->dlh = quot >> 8;
890 up->mdr1 = UART_OMAP_MDR1_DISABLE;
891
892 up->fcr = UART_FCR_R_TRIG_01 | UART_FCR_T_TRIG_01 |
893 UART_FCR_ENABLE_FIFO;
894
895 /*
896 * Ok, we're now changing the port state. Do it with
897 * interrupts disabled.
898 */
899 pm_runtime_get_sync(up->dev);
900 spin_lock_irqsave(&up->port.lock, flags);
901
902 /*
903 * Update the per-port timeout.
904 */
905 uart_update_timeout(port, termios->c_cflag, baud);
906
907 up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
908 if (termios->c_iflag & INPCK)
909 up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
910 if (termios->c_iflag & (BRKINT | PARMRK))
911 up->port.read_status_mask |= UART_LSR_BI;
912
913 /*
914 * Characters to ignore
915 */
916 up->port.ignore_status_mask = 0;
917 if (termios->c_iflag & IGNPAR)
918 up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
919 if (termios->c_iflag & IGNBRK) {
920 up->port.ignore_status_mask |= UART_LSR_BI;
921 /*
922 * If we're ignoring parity and break indicators,
923 * ignore overruns too (for real raw support).
924 */
925 if (termios->c_iflag & IGNPAR)
926 up->port.ignore_status_mask |= UART_LSR_OE;
927 }
928
929 /*
930 * ignore all characters if CREAD is not set
931 */
932 if ((termios->c_cflag & CREAD) == 0)
933 up->port.ignore_status_mask |= UART_LSR_DR;
934
935 /*
936 * Modem status interrupts
937 */
938 up->ier &= ~UART_IER_MSI;
939 if (UART_ENABLE_MS(&up->port, termios->c_cflag))
940 up->ier |= UART_IER_MSI;
941 serial_out(up, UART_IER, up->ier);
942 serial_out(up, UART_LCR, cval); /* reset DLAB */
943 up->lcr = cval;
944 up->scr = 0;
945
946 /* FIFOs and DMA Settings */
947
948 /* FCR can be changed only when the
949 * baud clock is not running
950 * DLL_REG and DLH_REG set to 0.
951 */
952 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
953 serial_out(up, UART_DLL, 0);
954 serial_out(up, UART_DLM, 0);
955 serial_out(up, UART_LCR, 0);
956
957 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
958
959 up->efr = serial_in(up, UART_EFR) & ~UART_EFR_ECB;
960 up->efr &= ~UART_EFR_SCD;
961 serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
962
963 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
964 up->mcr = serial_in(up, UART_MCR) & ~UART_MCR_TCRTLR;
965 serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
966 /* FIFO ENABLE, DMA MODE */
967
968 up->scr |= OMAP_UART_SCR_RX_TRIG_GRANU1_MASK;
969 /*
970 * NOTE: Setting OMAP_UART_SCR_RX_TRIG_GRANU1_MASK
971 * sets Enables the granularity of 1 for TRIGGER RX
972 * level. Along with setting RX FIFO trigger level
973 * to 1 (as noted below, 16 characters) and TLR[3:0]
974 * to zero this will result RX FIFO threshold level
975 * to 1 character, instead of 16 as noted in comment
976 * below.
977 */
978
979 /* Set receive FIFO threshold to 16 characters and
980 * transmit FIFO threshold to 32 spaces
981 */
982 up->fcr &= ~OMAP_UART_FCR_RX_FIFO_TRIG_MASK;
983 up->fcr &= ~OMAP_UART_FCR_TX_FIFO_TRIG_MASK;
984 up->fcr |= UART_FCR6_R_TRIGGER_16 | UART_FCR6_T_TRIGGER_24 |
985 UART_FCR_ENABLE_FIFO;
986
987 serial_out(up, UART_FCR, up->fcr);
988 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
989
990 serial_out(up, UART_OMAP_SCR, up->scr);
991
992 /* Reset UART_MCR_TCRTLR: this must be done with the EFR_ECB bit set */
993 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
994 serial_out(up, UART_MCR, up->mcr);
995 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
996 serial_out(up, UART_EFR, up->efr);
997 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
998
999 /* Protocol, Baud Rate, and Interrupt Settings */
1000
1001 if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
1002 serial_omap_mdr1_errataset(up, up->mdr1);
1003 else
1004 serial_out(up, UART_OMAP_MDR1, up->mdr1);
1005
1006 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
1007 serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
1008
1009 serial_out(up, UART_LCR, 0);
1010 serial_out(up, UART_IER, 0);
1011 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
1012
1013 serial_out(up, UART_DLL, up->dll); /* LS of divisor */
1014 serial_out(up, UART_DLM, up->dlh); /* MS of divisor */
1015
1016 serial_out(up, UART_LCR, 0);
1017 serial_out(up, UART_IER, up->ier);
1018 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
1019
1020 serial_out(up, UART_EFR, up->efr);
1021 serial_out(up, UART_LCR, cval);
1022
1023 if (!serial_omap_baud_is_mode16(port, baud))
1024 up->mdr1 = UART_OMAP_MDR1_13X_MODE;
1025 else
1026 up->mdr1 = UART_OMAP_MDR1_16X_MODE;
1027
1028 if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
1029 serial_omap_mdr1_errataset(up, up->mdr1);
1030 else
1031 serial_out(up, UART_OMAP_MDR1, up->mdr1);
1032
1033 /* Configure flow control */
1034 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
1035
1036 /* XON1/XOFF1 accessible mode B, TCRTLR=0, ECB=0 */
1037 serial_out(up, UART_XON1, termios->c_cc[VSTART]);
1038 serial_out(up, UART_XOFF1, termios->c_cc[VSTOP]);
1039
1040 /* Enable access to TCR/TLR */
1041 serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
1042 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
1043 serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
1044
1045 serial_out(up, UART_TI752_TCR, OMAP_UART_TCR_TRIG);
1046
1047 up->port.status &= ~(UPSTAT_AUTOCTS | UPSTAT_AUTORTS | UPSTAT_AUTOXOFF);
1048
1049 if (termios->c_cflag & CRTSCTS && up->port.flags & UPF_HARD_FLOW) {
1050 /* Enable AUTOCTS (autoRTS is enabled when RTS is raised) */
1051 up->port.status |= UPSTAT_AUTOCTS | UPSTAT_AUTORTS;
1052 up->efr |= UART_EFR_CTS;
1053 } else {
1054 /* Disable AUTORTS and AUTOCTS */
1055 up->efr &= ~(UART_EFR_CTS | UART_EFR_RTS);
1056 }
1057
1058 if (up->port.flags & UPF_SOFT_FLOW) {
1059 /* clear SW control mode bits */
1060 up->efr &= OMAP_UART_SW_CLR;
1061
1062 /*
1063 * IXON Flag:
1064 * Enable XON/XOFF flow control on input.
1065 * Receiver compares XON1, XOFF1.
1066 */
1067 if (termios->c_iflag & IXON)
1068 up->efr |= OMAP_UART_SW_RX;
1069
1070 /*
1071 * IXOFF Flag:
1072 * Enable XON/XOFF flow control on output.
1073 * Transmit XON1, XOFF1
1074 */
1075 if (termios->c_iflag & IXOFF) {
1076 up->port.status |= UPSTAT_AUTOXOFF;
1077 up->efr |= OMAP_UART_SW_TX;
1078 }
1079
1080 /*
1081 * IXANY Flag:
1082 * Enable any character to restart output.
1083 * Operation resumes after receiving any
1084 * character after recognition of the XOFF character
1085 */
1086 if (termios->c_iflag & IXANY)
1087 up->mcr |= UART_MCR_XONANY;
1088 else
1089 up->mcr &= ~UART_MCR_XONANY;
1090 }
1091 serial_out(up, UART_MCR, up->mcr);
1092 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
1093 serial_out(up, UART_EFR, up->efr);
1094 serial_out(up, UART_LCR, up->lcr);
1095
1096 serial_omap_set_mctrl(&up->port, up->port.mctrl);
1097
1098 spin_unlock_irqrestore(&up->port.lock, flags);
1099 pm_runtime_mark_last_busy(up->dev);
1100 pm_runtime_put_autosuspend(up->dev);
1101 dev_dbg(up->port.dev, "serial_omap_set_termios+%d\n", up->port.line);
1102}
1103
1104static void
1105serial_omap_pm(struct uart_port *port, unsigned int state,
1106 unsigned int oldstate)
1107{
1108 struct uart_omap_port *up = to_uart_omap_port(port);
1109 unsigned char efr;
1110
1111 dev_dbg(up->port.dev, "serial_omap_pm+%d\n", up->port.line);
1112
1113 pm_runtime_get_sync(up->dev);
1114 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
1115 efr = serial_in(up, UART_EFR);
1116 serial_out(up, UART_EFR, efr | UART_EFR_ECB);
1117 serial_out(up, UART_LCR, 0);
1118
1119 serial_out(up, UART_IER, (state != 0) ? UART_IERX_SLEEP : 0);
1120 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
1121 serial_out(up, UART_EFR, efr);
1122 serial_out(up, UART_LCR, 0);
1123
1124 pm_runtime_mark_last_busy(up->dev);
1125 pm_runtime_put_autosuspend(up->dev);
1126}
1127
1128static void serial_omap_release_port(struct uart_port *port)
1129{
1130 dev_dbg(port->dev, "serial_omap_release_port+\n");
1131}
1132
1133static int serial_omap_request_port(struct uart_port *port)
1134{
1135 dev_dbg(port->dev, "serial_omap_request_port+\n");
1136 return 0;
1137}
1138
1139static void serial_omap_config_port(struct uart_port *port, int flags)
1140{
1141 struct uart_omap_port *up = to_uart_omap_port(port);
1142
1143 dev_dbg(up->port.dev, "serial_omap_config_port+%d\n",
1144 up->port.line);
1145 up->port.type = PORT_OMAP;
1146 up->port.flags |= UPF_SOFT_FLOW | UPF_HARD_FLOW;
1147}
1148
1149static int
1150serial_omap_verify_port(struct uart_port *port, struct serial_struct *ser)
1151{
1152 /* we don't want the core code to modify any port params */
1153 dev_dbg(port->dev, "serial_omap_verify_port+\n");
1154 return -EINVAL;
1155}
1156
1157static const char *
1158serial_omap_type(struct uart_port *port)
1159{
1160 struct uart_omap_port *up = to_uart_omap_port(port);
1161
1162 dev_dbg(up->port.dev, "serial_omap_type+%d\n", up->port.line);
1163 return up->name;
1164}
1165
1166#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
1167
1168static void __maybe_unused wait_for_xmitr(struct uart_omap_port *up)
1169{
1170 unsigned int status, tmout = 10000;
1171
1172 /* Wait up to 10ms for the character(s) to be sent. */
1173 do {
1174 status = serial_in(up, UART_LSR);
1175
1176 if (status & UART_LSR_BI)
1177 up->lsr_break_flag = UART_LSR_BI;
1178
1179 if (--tmout == 0)
1180 break;
1181 udelay(1);
1182 } while ((status & BOTH_EMPTY) != BOTH_EMPTY);
1183
1184 /* Wait up to 1s for flow control if necessary */
1185 if (up->port.flags & UPF_CONS_FLOW) {
1186 tmout = 1000000;
1187 for (tmout = 1000000; tmout; tmout--) {
1188 unsigned int msr = serial_in(up, UART_MSR);
1189
1190 up->msr_saved_flags |= msr & MSR_SAVE_FLAGS;
1191 if (msr & UART_MSR_CTS)
1192 break;
1193
1194 udelay(1);
1195 }
1196 }
1197}
1198
1199#ifdef CONFIG_CONSOLE_POLL
1200
1201static void serial_omap_poll_put_char(struct uart_port *port, unsigned char ch)
1202{
1203 struct uart_omap_port *up = to_uart_omap_port(port);
1204
1205 pm_runtime_get_sync(up->dev);
1206 wait_for_xmitr(up);
1207 serial_out(up, UART_TX, ch);
1208 pm_runtime_mark_last_busy(up->dev);
1209 pm_runtime_put_autosuspend(up->dev);
1210}
1211
1212static int serial_omap_poll_get_char(struct uart_port *port)
1213{
1214 struct uart_omap_port *up = to_uart_omap_port(port);
1215 unsigned int status;
1216
1217 pm_runtime_get_sync(up->dev);
1218 status = serial_in(up, UART_LSR);
1219 if (!(status & UART_LSR_DR)) {
1220 status = NO_POLL_CHAR;
1221 goto out;
1222 }
1223
1224 status = serial_in(up, UART_RX);
1225
1226out:
1227 pm_runtime_mark_last_busy(up->dev);
1228 pm_runtime_put_autosuspend(up->dev);
1229
1230 return status;
1231}
1232
1233#endif /* CONFIG_CONSOLE_POLL */
1234
1235#ifdef CONFIG_SERIAL_OMAP_CONSOLE
1236
1237static struct uart_omap_port *serial_omap_console_ports[OMAP_MAX_HSUART_PORTS];
1238
1239static struct uart_driver serial_omap_reg;
1240
1241static void serial_omap_console_putchar(struct uart_port *port, int ch)
1242{
1243 struct uart_omap_port *up = to_uart_omap_port(port);
1244
1245 wait_for_xmitr(up);
1246 serial_out(up, UART_TX, ch);
1247}
1248
1249static void
1250serial_omap_console_write(struct console *co, const char *s,
1251 unsigned int count)
1252{
1253 struct uart_omap_port *up = serial_omap_console_ports[co->index];
1254 unsigned long flags;
1255 unsigned int ier;
1256 int locked = 1;
1257
1258 pm_runtime_get_sync(up->dev);
1259
1260 local_irq_save(flags);
1261 if (up->port.sysrq)
1262 locked = 0;
1263 else if (oops_in_progress)
1264 locked = spin_trylock(&up->port.lock);
1265 else
1266 spin_lock(&up->port.lock);
1267
1268 /*
1269 * First save the IER then disable the interrupts
1270 */
1271 ier = serial_in(up, UART_IER);
1272 serial_out(up, UART_IER, 0);
1273
1274 uart_console_write(&up->port, s, count, serial_omap_console_putchar);
1275
1276 /*
1277 * Finally, wait for transmitter to become empty
1278 * and restore the IER
1279 */
1280 wait_for_xmitr(up);
1281 serial_out(up, UART_IER, ier);
1282 /*
1283 * The receive handling will happen properly because the
1284 * receive ready bit will still be set; it is not cleared
1285 * on read. However, modem control will not, we must
1286 * call it if we have saved something in the saved flags
1287 * while processing with interrupts off.
1288 */
1289 if (up->msr_saved_flags)
1290 check_modem_status(up);
1291
1292 pm_runtime_mark_last_busy(up->dev);
1293 pm_runtime_put_autosuspend(up->dev);
1294 if (locked)
1295 spin_unlock(&up->port.lock);
1296 local_irq_restore(flags);
1297}
1298
1299static int __init
1300serial_omap_console_setup(struct console *co, char *options)
1301{
1302 struct uart_omap_port *up;
1303 int baud = 115200;
1304 int bits = 8;
1305 int parity = 'n';
1306 int flow = 'n';
1307
1308 if (serial_omap_console_ports[co->index] == NULL)
1309 return -ENODEV;
1310 up = serial_omap_console_ports[co->index];
1311
1312 if (options)
1313 uart_parse_options(options, &baud, &parity, &bits, &flow);
1314
1315 return uart_set_options(&up->port, co, baud, parity, bits, flow);
1316}
1317
1318static struct console serial_omap_console = {
1319 .name = OMAP_SERIAL_NAME,
1320 .write = serial_omap_console_write,
1321 .device = uart_console_device,
1322 .setup = serial_omap_console_setup,
1323 .flags = CON_PRINTBUFFER,
1324 .index = -1,
1325 .data = &serial_omap_reg,
1326};
1327
1328static void serial_omap_add_console_port(struct uart_omap_port *up)
1329{
1330 serial_omap_console_ports[up->port.line] = up;
1331}
1332
1333#define OMAP_CONSOLE (&serial_omap_console)
1334
1335#else
1336
1337#define OMAP_CONSOLE NULL
1338
1339static inline void serial_omap_add_console_port(struct uart_omap_port *up)
1340{}
1341
1342#endif
1343
1344/* Enable or disable the rs485 support */
1345static int
1346serial_omap_config_rs485(struct uart_port *port, struct serial_rs485 *rs485)
1347{
1348 struct uart_omap_port *up = to_uart_omap_port(port);
1349 unsigned int mode;
1350 int val;
1351
1352 pm_runtime_get_sync(up->dev);
1353
1354 /* Disable interrupts from this port */
1355 mode = up->ier;
1356 up->ier = 0;
1357 serial_out(up, UART_IER, 0);
1358
1359 /* Clamp the delays to [0, 100ms] */
1360 rs485->delay_rts_before_send = min(rs485->delay_rts_before_send, 100U);
1361 rs485->delay_rts_after_send = min(rs485->delay_rts_after_send, 100U);
1362
1363 /* store new config */
1364 port->rs485 = *rs485;
1365
1366 /*
1367 * Just as a precaution, only allow rs485
1368 * to be enabled if the gpio pin is valid
1369 */
1370 if (gpio_is_valid(up->rts_gpio)) {
1371 /* enable / disable rts */
1372 val = (port->rs485.flags & SER_RS485_ENABLED) ?
1373 SER_RS485_RTS_AFTER_SEND : SER_RS485_RTS_ON_SEND;
1374 val = (port->rs485.flags & val) ? 1 : 0;
1375 gpio_set_value(up->rts_gpio, val);
1376 } else
1377 port->rs485.flags &= ~SER_RS485_ENABLED;
1378
1379 /* Enable interrupts */
1380 up->ier = mode;
1381 serial_out(up, UART_IER, up->ier);
1382
1383 /* If RS-485 is disabled, make sure the THR interrupt is fired when
1384 * TX FIFO is below the trigger level.
1385 */
1386 if (!(port->rs485.flags & SER_RS485_ENABLED) &&
1387 (up->scr & OMAP_UART_SCR_TX_EMPTY)) {
1388 up->scr &= ~OMAP_UART_SCR_TX_EMPTY;
1389 serial_out(up, UART_OMAP_SCR, up->scr);
1390 }
1391
1392 pm_runtime_mark_last_busy(up->dev);
1393 pm_runtime_put_autosuspend(up->dev);
1394
1395 return 0;
1396}
1397
1398static struct uart_ops serial_omap_pops = {
1399 .tx_empty = serial_omap_tx_empty,
1400 .set_mctrl = serial_omap_set_mctrl,
1401 .get_mctrl = serial_omap_get_mctrl,
1402 .stop_tx = serial_omap_stop_tx,
1403 .start_tx = serial_omap_start_tx,
1404 .throttle = serial_omap_throttle,
1405 .unthrottle = serial_omap_unthrottle,
1406 .stop_rx = serial_omap_stop_rx,
1407 .enable_ms = serial_omap_enable_ms,
1408 .break_ctl = serial_omap_break_ctl,
1409 .startup = serial_omap_startup,
1410 .shutdown = serial_omap_shutdown,
1411 .set_termios = serial_omap_set_termios,
1412 .pm = serial_omap_pm,
1413 .type = serial_omap_type,
1414 .release_port = serial_omap_release_port,
1415 .request_port = serial_omap_request_port,
1416 .config_port = serial_omap_config_port,
1417 .verify_port = serial_omap_verify_port,
1418#ifdef CONFIG_CONSOLE_POLL
1419 .poll_put_char = serial_omap_poll_put_char,
1420 .poll_get_char = serial_omap_poll_get_char,
1421#endif
1422};
1423
1424static struct uart_driver serial_omap_reg = {
1425 .owner = THIS_MODULE,
1426 .driver_name = "OMAP-SERIAL",
1427 .dev_name = OMAP_SERIAL_NAME,
1428 .nr = OMAP_MAX_HSUART_PORTS,
1429 .cons = OMAP_CONSOLE,
1430};
1431
1432#ifdef CONFIG_PM_SLEEP
1433static int serial_omap_prepare(struct device *dev)
1434{
1435 struct uart_omap_port *up = dev_get_drvdata(dev);
1436
1437 up->is_suspending = true;
1438
1439 return 0;
1440}
1441
1442static void serial_omap_complete(struct device *dev)
1443{
1444 struct uart_omap_port *up = dev_get_drvdata(dev);
1445
1446 up->is_suspending = false;
1447}
1448
1449static int serial_omap_suspend(struct device *dev)
1450{
1451 struct uart_omap_port *up = dev_get_drvdata(dev);
1452
1453 uart_suspend_port(&serial_omap_reg, &up->port);
1454 flush_work(&up->qos_work);
1455
1456 if (device_may_wakeup(dev))
1457 serial_omap_enable_wakeup(up, true);
1458 else
1459 serial_omap_enable_wakeup(up, false);
1460
1461 return 0;
1462}
1463
1464static int serial_omap_resume(struct device *dev)
1465{
1466 struct uart_omap_port *up = dev_get_drvdata(dev);
1467
1468 if (device_may_wakeup(dev))
1469 serial_omap_enable_wakeup(up, false);
1470
1471 uart_resume_port(&serial_omap_reg, &up->port);
1472
1473 return 0;
1474}
1475#else
1476#define serial_omap_prepare NULL
1477#define serial_omap_complete NULL
1478#endif /* CONFIG_PM_SLEEP */
1479
1480static void omap_serial_fill_features_erratas(struct uart_omap_port *up)
1481{
1482 u32 mvr, scheme;
1483 u16 revision, major, minor;
1484
1485 mvr = readl(up->port.membase + (UART_OMAP_MVER << up->port.regshift));
1486
1487 /* Check revision register scheme */
1488 scheme = mvr >> OMAP_UART_MVR_SCHEME_SHIFT;
1489
1490 switch (scheme) {
1491 case 0: /* Legacy Scheme: OMAP2/3 */
1492 /* MINOR_REV[0:4], MAJOR_REV[4:7] */
1493 major = (mvr & OMAP_UART_LEGACY_MVR_MAJ_MASK) >>
1494 OMAP_UART_LEGACY_MVR_MAJ_SHIFT;
1495 minor = (mvr & OMAP_UART_LEGACY_MVR_MIN_MASK);
1496 break;
1497 case 1:
1498 /* New Scheme: OMAP4+ */
1499 /* MINOR_REV[0:5], MAJOR_REV[8:10] */
1500 major = (mvr & OMAP_UART_MVR_MAJ_MASK) >>
1501 OMAP_UART_MVR_MAJ_SHIFT;
1502 minor = (mvr & OMAP_UART_MVR_MIN_MASK);
1503 break;
1504 default:
1505 dev_warn(up->dev,
1506 "Unknown %s revision, defaulting to highest\n",
1507 up->name);
1508 /* highest possible revision */
1509 major = 0xff;
1510 minor = 0xff;
1511 }
1512
1513 /* normalize revision for the driver */
1514 revision = UART_BUILD_REVISION(major, minor);
1515
1516 switch (revision) {
1517 case OMAP_UART_REV_46:
1518 up->errata |= (UART_ERRATA_i202_MDR1_ACCESS |
1519 UART_ERRATA_i291_DMA_FORCEIDLE);
1520 break;
1521 case OMAP_UART_REV_52:
1522 up->errata |= (UART_ERRATA_i202_MDR1_ACCESS |
1523 UART_ERRATA_i291_DMA_FORCEIDLE);
1524 up->features |= OMAP_UART_WER_HAS_TX_WAKEUP;
1525 break;
1526 case OMAP_UART_REV_63:
1527 up->errata |= UART_ERRATA_i202_MDR1_ACCESS;
1528 up->features |= OMAP_UART_WER_HAS_TX_WAKEUP;
1529 break;
1530 default:
1531 break;
1532 }
1533}
1534
1535static struct omap_uart_port_info *of_get_uart_port_info(struct device *dev)
1536{
1537 struct omap_uart_port_info *omap_up_info;
1538
1539 omap_up_info = devm_kzalloc(dev, sizeof(*omap_up_info), GFP_KERNEL);
1540 if (!omap_up_info)
1541 return NULL; /* out of memory */
1542
1543 of_property_read_u32(dev->of_node, "clock-frequency",
1544 &omap_up_info->uartclk);
1545 return omap_up_info;
1546}
1547
1548static int serial_omap_probe_rs485(struct uart_omap_port *up,
1549 struct device_node *np)
1550{
1551 struct serial_rs485 *rs485conf = &up->port.rs485;
1552 u32 rs485_delay[2];
1553 enum of_gpio_flags flags;
1554 int ret;
1555
1556 rs485conf->flags = 0;
1557 up->rts_gpio = -EINVAL;
1558
1559 if (!np)
1560 return 0;
1561
1562 if (of_property_read_bool(np, "rs485-rts-active-high"))
1563 rs485conf->flags |= SER_RS485_RTS_ON_SEND;
1564 else
1565 rs485conf->flags |= SER_RS485_RTS_AFTER_SEND;
1566
1567 /* check for tx enable gpio */
1568 up->rts_gpio = of_get_named_gpio_flags(np, "rts-gpio", 0, &flags);
1569 if (gpio_is_valid(up->rts_gpio)) {
1570 ret = devm_gpio_request(up->dev, up->rts_gpio, "omap-serial");
1571 if (ret < 0)
1572 return ret;
1573 ret = gpio_direction_output(up->rts_gpio,
1574 flags & SER_RS485_RTS_AFTER_SEND);
1575 if (ret < 0)
1576 return ret;
1577 } else if (up->rts_gpio == -EPROBE_DEFER) {
1578 return -EPROBE_DEFER;
1579 } else {
1580 up->rts_gpio = -EINVAL;
1581 }
1582
1583 if (of_property_read_u32_array(np, "rs485-rts-delay",
1584 rs485_delay, 2) == 0) {
1585 rs485conf->delay_rts_before_send = rs485_delay[0];
1586 rs485conf->delay_rts_after_send = rs485_delay[1];
1587 }
1588
1589 if (of_property_read_bool(np, "rs485-rx-during-tx"))
1590 rs485conf->flags |= SER_RS485_RX_DURING_TX;
1591
1592 if (of_property_read_bool(np, "linux,rs485-enabled-at-boot-time"))
1593 rs485conf->flags |= SER_RS485_ENABLED;
1594
1595 return 0;
1596}
1597
1598static int serial_omap_probe(struct platform_device *pdev)
1599{
1600 struct omap_uart_port_info *omap_up_info = dev_get_platdata(&pdev->dev);
1601 struct uart_omap_port *up;
1602 struct resource *mem;
1603 void __iomem *base;
1604 int uartirq = 0;
1605 int wakeirq = 0;
1606 int ret;
1607
1608 /* The optional wakeirq may be specified in the board dts file */
1609 if (pdev->dev.of_node) {
1610 uartirq = irq_of_parse_and_map(pdev->dev.of_node, 0);
1611 if (!uartirq)
1612 return -EPROBE_DEFER;
1613 wakeirq = irq_of_parse_and_map(pdev->dev.of_node, 1);
1614 omap_up_info = of_get_uart_port_info(&pdev->dev);
1615 pdev->dev.platform_data = omap_up_info;
1616 } else {
1617 uartirq = platform_get_irq(pdev, 0);
1618 if (uartirq < 0)
1619 return -EPROBE_DEFER;
1620 }
1621
1622 up = devm_kzalloc(&pdev->dev, sizeof(*up), GFP_KERNEL);
1623 if (!up)
1624 return -ENOMEM;
1625
1626 mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1627 base = devm_ioremap_resource(&pdev->dev, mem);
1628 if (IS_ERR(base))
1629 return PTR_ERR(base);
1630
1631 up->dev = &pdev->dev;
1632 up->port.dev = &pdev->dev;
1633 up->port.type = PORT_OMAP;
1634 up->port.iotype = UPIO_MEM;
1635 up->port.irq = uartirq;
1636 up->port.regshift = 2;
1637 up->port.fifosize = 64;
1638 up->port.ops = &serial_omap_pops;
1639
1640 if (pdev->dev.of_node)
1641 ret = of_alias_get_id(pdev->dev.of_node, "serial");
1642 else
1643 ret = pdev->id;
1644
1645 if (ret < 0) {
1646 dev_err(&pdev->dev, "failed to get alias/pdev id, errno %d\n",
1647 ret);
1648 goto err_port_line;
1649 }
1650 up->port.line = ret;
1651
1652 if (up->port.line >= OMAP_MAX_HSUART_PORTS) {
1653 dev_err(&pdev->dev, "uart ID %d > MAX %d.\n", up->port.line,
1654 OMAP_MAX_HSUART_PORTS);
1655 ret = -ENXIO;
1656 goto err_port_line;
1657 }
1658
1659 up->wakeirq = wakeirq;
1660 if (!up->wakeirq)
1661 dev_info(up->port.dev, "no wakeirq for uart%d\n",
1662 up->port.line);
1663
1664 ret = serial_omap_probe_rs485(up, pdev->dev.of_node);
1665 if (ret < 0)
1666 goto err_rs485;
1667
1668 sprintf(up->name, "OMAP UART%d", up->port.line);
1669 up->port.mapbase = mem->start;
1670 up->port.membase = base;
1671 up->port.flags = omap_up_info->flags;
1672 up->port.uartclk = omap_up_info->uartclk;
1673 up->port.rs485_config = serial_omap_config_rs485;
1674 if (!up->port.uartclk) {
1675 up->port.uartclk = DEFAULT_CLK_SPEED;
1676 dev_warn(&pdev->dev,
1677 "No clock speed specified: using default: %d\n",
1678 DEFAULT_CLK_SPEED);
1679 }
1680
1681 up->latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
1682 up->calc_latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
1683 pm_qos_add_request(&up->pm_qos_request,
1684 PM_QOS_CPU_DMA_LATENCY, up->latency);
1685 INIT_WORK(&up->qos_work, serial_omap_uart_qos_work);
1686
1687 platform_set_drvdata(pdev, up);
1688 if (omap_up_info->autosuspend_timeout == 0)
1689 omap_up_info->autosuspend_timeout = -1;
1690
1691 device_init_wakeup(up->dev, true);
1692 pm_runtime_use_autosuspend(&pdev->dev);
1693 pm_runtime_set_autosuspend_delay(&pdev->dev,
1694 omap_up_info->autosuspend_timeout);
1695
1696 pm_runtime_irq_safe(&pdev->dev);
1697 pm_runtime_enable(&pdev->dev);
1698
1699 pm_runtime_get_sync(&pdev->dev);
1700
1701 omap_serial_fill_features_erratas(up);
1702
1703 ui[up->port.line] = up;
1704 serial_omap_add_console_port(up);
1705
1706 ret = uart_add_one_port(&serial_omap_reg, &up->port);
1707 if (ret != 0)
1708 goto err_add_port;
1709
1710 pm_runtime_mark_last_busy(up->dev);
1711 pm_runtime_put_autosuspend(up->dev);
1712 return 0;
1713
1714err_add_port:
1715 pm_runtime_put(&pdev->dev);
1716 pm_runtime_disable(&pdev->dev);
1717 pm_qos_remove_request(&up->pm_qos_request);
1718 device_init_wakeup(up->dev, false);
1719err_rs485:
1720err_port_line:
1721 return ret;
1722}
1723
1724static int serial_omap_remove(struct platform_device *dev)
1725{
1726 struct uart_omap_port *up = platform_get_drvdata(dev);
1727
1728 pm_runtime_put_sync(up->dev);
1729 pm_runtime_disable(up->dev);
1730 uart_remove_one_port(&serial_omap_reg, &up->port);
1731 pm_qos_remove_request(&up->pm_qos_request);
1732 device_init_wakeup(&dev->dev, false);
1733
1734 return 0;
1735}
1736
1737/*
1738 * Work Around for Errata i202 (2430, 3430, 3630, 4430 and 4460)
1739 * The access to uart register after MDR1 Access
1740 * causes UART to corrupt data.
1741 *
1742 * Need a delay =
1743 * 5 L4 clock cycles + 5 UART functional clock cycle (@48MHz = ~0.2uS)
1744 * give 10 times as much
1745 */
1746static void serial_omap_mdr1_errataset(struct uart_omap_port *up, u8 mdr1)
1747{
1748 u8 timeout = 255;
1749
1750 serial_out(up, UART_OMAP_MDR1, mdr1);
1751 udelay(2);
1752 serial_out(up, UART_FCR, up->fcr | UART_FCR_CLEAR_XMIT |
1753 UART_FCR_CLEAR_RCVR);
1754 /*
1755 * Wait for FIFO to empty: when empty, RX_FIFO_E bit is 0 and
1756 * TX_FIFO_E bit is 1.
1757 */
1758 while (UART_LSR_THRE != (serial_in(up, UART_LSR) &
1759 (UART_LSR_THRE | UART_LSR_DR))) {
1760 timeout--;
1761 if (!timeout) {
1762 /* Should *never* happen. we warn and carry on */
1763 dev_crit(up->dev, "Errata i202: timedout %x\n",
1764 serial_in(up, UART_LSR));
1765 break;
1766 }
1767 udelay(1);
1768 }
1769}
1770
1771#ifdef CONFIG_PM
1772static void serial_omap_restore_context(struct uart_omap_port *up)
1773{
1774 if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
1775 serial_omap_mdr1_errataset(up, UART_OMAP_MDR1_DISABLE);
1776 else
1777 serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_DISABLE);
1778
1779 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /* Config B mode */
1780 serial_out(up, UART_EFR, UART_EFR_ECB);
1781 serial_out(up, UART_LCR, 0x0); /* Operational mode */
1782 serial_out(up, UART_IER, 0x0);
1783 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /* Config B mode */
1784 serial_out(up, UART_DLL, up->dll);
1785 serial_out(up, UART_DLM, up->dlh);
1786 serial_out(up, UART_LCR, 0x0); /* Operational mode */
1787 serial_out(up, UART_IER, up->ier);
1788 serial_out(up, UART_FCR, up->fcr);
1789 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
1790 serial_out(up, UART_MCR, up->mcr);
1791 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /* Config B mode */
1792 serial_out(up, UART_OMAP_SCR, up->scr);
1793 serial_out(up, UART_EFR, up->efr);
1794 serial_out(up, UART_LCR, up->lcr);
1795 if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
1796 serial_omap_mdr1_errataset(up, up->mdr1);
1797 else
1798 serial_out(up, UART_OMAP_MDR1, up->mdr1);
1799 serial_out(up, UART_OMAP_WER, up->wer);
1800}
1801
1802static int serial_omap_runtime_suspend(struct device *dev)
1803{
1804 struct uart_omap_port *up = dev_get_drvdata(dev);
1805
1806 if (!up)
1807 return -EINVAL;
1808
1809 /*
1810 * When using 'no_console_suspend', the console UART must not be
1811 * suspended. Since driver suspend is managed by runtime suspend,
1812 * preventing runtime suspend (by returning error) will keep device
1813 * active during suspend.
1814 */
1815 if (up->is_suspending && !console_suspend_enabled &&
1816 uart_console(&up->port))
1817 return -EBUSY;
1818
1819 up->context_loss_cnt = serial_omap_get_context_loss_count(up);
1820
1821 serial_omap_enable_wakeup(up, true);
1822
1823 up->latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
1824 schedule_work(&up->qos_work);
1825
1826 return 0;
1827}
1828
1829static int serial_omap_runtime_resume(struct device *dev)
1830{
1831 struct uart_omap_port *up = dev_get_drvdata(dev);
1832
1833 int loss_cnt = serial_omap_get_context_loss_count(up);
1834
1835 serial_omap_enable_wakeup(up, false);
1836
1837 if (loss_cnt < 0) {
1838 dev_dbg(dev, "serial_omap_get_context_loss_count failed : %d\n",
1839 loss_cnt);
1840 serial_omap_restore_context(up);
1841 } else if (up->context_loss_cnt != loss_cnt) {
1842 serial_omap_restore_context(up);
1843 }
1844 up->latency = up->calc_latency;
1845 schedule_work(&up->qos_work);
1846
1847 return 0;
1848}
1849#endif
1850
1851static const struct dev_pm_ops serial_omap_dev_pm_ops = {
1852 SET_SYSTEM_SLEEP_PM_OPS(serial_omap_suspend, serial_omap_resume)
1853 SET_RUNTIME_PM_OPS(serial_omap_runtime_suspend,
1854 serial_omap_runtime_resume, NULL)
1855 .prepare = serial_omap_prepare,
1856 .complete = serial_omap_complete,
1857};
1858
1859#if defined(CONFIG_OF)
1860static const struct of_device_id omap_serial_of_match[] = {
1861 { .compatible = "ti,omap2-uart" },
1862 { .compatible = "ti,omap3-uart" },
1863 { .compatible = "ti,omap4-uart" },
1864 {},
1865};
1866MODULE_DEVICE_TABLE(of, omap_serial_of_match);
1867#endif
1868
1869static struct platform_driver serial_omap_driver = {
1870 .probe = serial_omap_probe,
1871 .remove = serial_omap_remove,
1872 .driver = {
1873 .name = OMAP_SERIAL_DRIVER_NAME,
1874 .pm = &serial_omap_dev_pm_ops,
1875 .of_match_table = of_match_ptr(omap_serial_of_match),
1876 },
1877};
1878
1879static int __init serial_omap_init(void)
1880{
1881 int ret;
1882
1883 ret = uart_register_driver(&serial_omap_reg);
1884 if (ret != 0)
1885 return ret;
1886 ret = platform_driver_register(&serial_omap_driver);
1887 if (ret != 0)
1888 uart_unregister_driver(&serial_omap_reg);
1889 return ret;
1890}
1891
1892static void __exit serial_omap_exit(void)
1893{
1894 platform_driver_unregister(&serial_omap_driver);
1895 uart_unregister_driver(&serial_omap_reg);
1896}
1897
1898module_init(serial_omap_init);
1899module_exit(serial_omap_exit);
1900
1901MODULE_DESCRIPTION("OMAP High Speed UART driver");
1902MODULE_LICENSE("GPL");
1903MODULE_AUTHOR("Texas Instruments Inc");