1/*
   2 * Driver for PowerMac Z85c30 based ESCC cell found in the
   3 * "macio" ASICs of various PowerMac models
   4 * 
   5 * Copyright (C) 2003 Ben. Herrenschmidt (benh@kernel.crashing.org)
   6 *
   7 * Derived from drivers/macintosh/macserial.c by Paul Mackerras
   8 * and drivers/serial/sunzilog.c by David S. Miller
   9 *
  10 * Hrm... actually, I ripped most of sunzilog (Thanks David !) and
  11 * adapted special tweaks needed for us. I don't think it's worth
  12 * merging back those though. The DMA code still has to get in
  13 * and once done, I expect that driver to remain fairly stable in
  14 * the long term, unless we change the driver model again...
  15 *
  16 * This program is free software; you can redistribute it and/or modify
  17 * it under the terms of the GNU General Public License as published by
  18 * the Free Software Foundation; either version 2 of the License, or
  19 * (at your option) any later version.
  20 *
  21 * This program is distributed in the hope that it will be useful,
  22 * but WITHOUT ANY WARRANTY; without even the implied warranty of
  23 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  24 * GNU General Public License for more details.
  25 *
  26 * You should have received a copy of the GNU General Public License
  27 * along with this program; if not, write to the Free Software
  28 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  29 *
  30 * 2004-08-06 Harald Welte <laforge@gnumonks.org>
  31 *	- Enable BREAK interrupt
  32 *	- Add support for sysreq
  33 *
  34 * TODO:   - Add DMA support
  35 *         - Defer port shutdown to a few seconds after close
  36 *         - maybe put something right into uap->clk_divisor
  37 */
  38
  39#undef DEBUG
  40#undef DEBUG_HARD
  41#undef USE_CTRL_O_SYSRQ
  42
  43#include <linux/module.h>
  44#include <linux/tty.h>
  45
  46#include <linux/tty_flip.h>
  47#include <linux/major.h>
  48#include <linux/string.h>
  49#include <linux/fcntl.h>
  50#include <linux/mm.h>
  51#include <linux/kernel.h>
  52#include <linux/delay.h>
  53#include <linux/init.h>
  54#include <linux/console.h>
  55#include <linux/adb.h>
  56#include <linux/pmu.h>
  57#include <linux/bitops.h>
  58#include <linux/sysrq.h>
  59#include <linux/mutex.h>
  60#include <asm/sections.h>
  61#include <asm/io.h>
  62#include <asm/irq.h>
  63
  64#ifdef CONFIG_PPC_PMAC
  65#include <asm/prom.h>
  66#include <asm/machdep.h>
  67#include <asm/pmac_feature.h>
  68#include <asm/dbdma.h>
  69#include <asm/macio.h>
  70#else
  71#include <linux/platform_device.h>
  72#define of_machine_is_compatible(x) (0)
  73#endif
  74
  75#if defined (CONFIG_SERIAL_PMACZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
  76#define SUPPORT_SYSRQ
  77#endif
  78
  79#include <linux/serial.h>
  80#include <linux/serial_core.h>
  81
  82#include "pmac_zilog.h"
  83
  84/* Not yet implemented */
  85#undef HAS_DBDMA
  86
  87static char version[] __initdata = "pmac_zilog: 0.6 (Benjamin Herrenschmidt <benh@kernel.crashing.org>)";
  88MODULE_AUTHOR("Benjamin Herrenschmidt <benh@kernel.crashing.org>");
  89MODULE_DESCRIPTION("Driver for the Mac and PowerMac serial ports.");
  90MODULE_LICENSE("GPL");
  91
  92#ifdef CONFIG_SERIAL_PMACZILOG_TTYS
  93#define PMACZILOG_MAJOR		TTY_MAJOR
  94#define PMACZILOG_MINOR		64
  95#define PMACZILOG_NAME		"ttyS"
  96#else
  97#define PMACZILOG_MAJOR		204
  98#define PMACZILOG_MINOR		192
  99#define PMACZILOG_NAME		"ttyPZ"
 100#endif
 101
 
 
 
 102
 103/*
 104 * For the sake of early serial console, we can do a pre-probe
 105 * (optional) of the ports at rather early boot time.
 106 */
 107static struct uart_pmac_port	pmz_ports[MAX_ZS_PORTS];
 108static int			pmz_ports_count;
 109static DEFINE_MUTEX(pmz_irq_mutex);
 110
 111static struct uart_driver pmz_uart_reg = {
 112	.owner		=	THIS_MODULE,
 113	.driver_name	=	PMACZILOG_NAME,
 114	.dev_name	=	PMACZILOG_NAME,
 115	.major		=	PMACZILOG_MAJOR,
 116	.minor		=	PMACZILOG_MINOR,
 117};
 118
 119
 120/* 
 121 * Load all registers to reprogram the port
 122 * This function must only be called when the TX is not busy.  The UART
 123 * port lock must be held and local interrupts disabled.
 124 */
 125static void pmz_load_zsregs(struct uart_pmac_port *uap, u8 *regs)
 126{
 127	int i;
 128
 129	if (ZS_IS_ASLEEP(uap))
 130		return;
 131
 132	/* Let pending transmits finish.  */
 133	for (i = 0; i < 1000; i++) {
 134		unsigned char stat = read_zsreg(uap, R1);
 135		if (stat & ALL_SNT)
 136			break;
 137		udelay(100);
 138	}
 139
 140	ZS_CLEARERR(uap);
 141	zssync(uap);
 142	ZS_CLEARFIFO(uap);
 143	zssync(uap);
 144	ZS_CLEARERR(uap);
 145
 146	/* Disable all interrupts.  */
 147	write_zsreg(uap, R1,
 148		    regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB));
 149
 150	/* Set parity, sync config, stop bits, and clock divisor.  */
 151	write_zsreg(uap, R4, regs[R4]);
 152
 153	/* Set misc. TX/RX control bits.  */
 154	write_zsreg(uap, R10, regs[R10]);
 155
 156	/* Set TX/RX controls sans the enable bits.  */
 157	write_zsreg(uap, R3, regs[R3] & ~RxENABLE);
 158	write_zsreg(uap, R5, regs[R5] & ~TxENABLE);
 159
 160	/* now set R7 "prime" on ESCC */
 161	write_zsreg(uap, R15, regs[R15] | EN85C30);
 162	write_zsreg(uap, R7, regs[R7P]);
 163
 164	/* make sure we use R7 "non-prime" on ESCC */
 165	write_zsreg(uap, R15, regs[R15] & ~EN85C30);
 166
 167	/* Synchronous mode config.  */
 168	write_zsreg(uap, R6, regs[R6]);
 169	write_zsreg(uap, R7, regs[R7]);
 170
 171	/* Disable baud generator.  */
 172	write_zsreg(uap, R14, regs[R14] & ~BRENAB);
 173
 174	/* Clock mode control.  */
 175	write_zsreg(uap, R11, regs[R11]);
 176
 177	/* Lower and upper byte of baud rate generator divisor.  */
 178	write_zsreg(uap, R12, regs[R12]);
 179	write_zsreg(uap, R13, regs[R13]);
 180	
 181	/* Now rewrite R14, with BRENAB (if set).  */
 182	write_zsreg(uap, R14, regs[R14]);
 183
 184	/* Reset external status interrupts.  */
 185	write_zsreg(uap, R0, RES_EXT_INT);
 186	write_zsreg(uap, R0, RES_EXT_INT);
 187
 188	/* Rewrite R3/R5, this time without enables masked.  */
 189	write_zsreg(uap, R3, regs[R3]);
 190	write_zsreg(uap, R5, regs[R5]);
 191
 192	/* Rewrite R1, this time without IRQ enabled masked.  */
 193	write_zsreg(uap, R1, regs[R1]);
 194
 195	/* Enable interrupts */
 196	write_zsreg(uap, R9, regs[R9]);
 197}
 198
 199/* 
 200 * We do like sunzilog to avoid disrupting pending Tx
 201 * Reprogram the Zilog channel HW registers with the copies found in the
 202 * software state struct.  If the transmitter is busy, we defer this update
 203 * until the next TX complete interrupt.  Else, we do it right now.
 204 *
 205 * The UART port lock must be held and local interrupts disabled.
 206 */
 207static void pmz_maybe_update_regs(struct uart_pmac_port *uap)
 208{
 209	if (!ZS_REGS_HELD(uap)) {
 210		if (ZS_TX_ACTIVE(uap)) {
 211			uap->flags |= PMACZILOG_FLAG_REGS_HELD;
 212		} else {
 213			pmz_debug("pmz: maybe_update_regs: updating\n");
 214			pmz_load_zsregs(uap, uap->curregs);
 215		}
 216	}
 217}
 218
 
 
 
 
 
 
 
 
 
 
 
 
 219static struct tty_struct *pmz_receive_chars(struct uart_pmac_port *uap)
 220{
 221	struct tty_struct *tty = NULL;
 222	unsigned char ch, r1, drop, error, flag;
 223	int loops = 0;
 224
 225	/* The interrupt can be enabled when the port isn't open, typically
 226	 * that happens when using one port is open and the other closed (stale
 227	 * interrupt) or when one port is used as a console.
 228	 */
 229	if (!ZS_IS_OPEN(uap)) {
 230		pmz_debug("pmz: draining input\n");
 231		/* Port is closed, drain input data */
 232		for (;;) {
 233			if ((++loops) > 1000)
 234				goto flood;
 235			(void)read_zsreg(uap, R1);
 236			write_zsreg(uap, R0, ERR_RES);
 237			(void)read_zsdata(uap);
 238			ch = read_zsreg(uap, R0);
 239			if (!(ch & Rx_CH_AV))
 240				break;
 241		}
 242		return NULL;
 243	}
 244
 245	/* Sanity check, make sure the old bug is no longer happening */
 246	if (uap->port.state == NULL || uap->port.state->port.tty == NULL) {
 247		WARN_ON(1);
 248		(void)read_zsdata(uap);
 249		return NULL;
 250	}
 251	tty = uap->port.state->port.tty;
 252
 253	while (1) {
 254		error = 0;
 255		drop = 0;
 256
 257		r1 = read_zsreg(uap, R1);
 258		ch = read_zsdata(uap);
 259
 260		if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
 261			write_zsreg(uap, R0, ERR_RES);
 262			zssync(uap);
 263		}
 264
 265		ch &= uap->parity_mask;
 266		if (ch == 0 && uap->flags & PMACZILOG_FLAG_BREAK) {
 267			uap->flags &= ~PMACZILOG_FLAG_BREAK;
 268		}
 269
 270#if defined(CONFIG_MAGIC_SYSRQ) && defined(CONFIG_SERIAL_CORE_CONSOLE)
 271#ifdef USE_CTRL_O_SYSRQ
 272		/* Handle the SysRq ^O Hack */
 273		if (ch == '\x0f') {
 274			uap->port.sysrq = jiffies + HZ*5;
 275			goto next_char;
 276		}
 277#endif /* USE_CTRL_O_SYSRQ */
 278		if (uap->port.sysrq) {
 279			int swallow;
 280			spin_unlock(&uap->port.lock);
 281			swallow = uart_handle_sysrq_char(&uap->port, ch);
 282			spin_lock(&uap->port.lock);
 283			if (swallow)
 284				goto next_char;
 285		}
 286#endif /* CONFIG_MAGIC_SYSRQ && CONFIG_SERIAL_CORE_CONSOLE */
 287
 288		/* A real serial line, record the character and status.  */
 289		if (drop)
 290			goto next_char;
 291
 292		flag = TTY_NORMAL;
 293		uap->port.icount.rx++;
 294
 295		if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR | BRK_ABRT)) {
 296			error = 1;
 297			if (r1 & BRK_ABRT) {
 298				pmz_debug("pmz: got break !\n");
 299				r1 &= ~(PAR_ERR | CRC_ERR);
 300				uap->port.icount.brk++;
 301				if (uart_handle_break(&uap->port))
 302					goto next_char;
 303			}
 304			else if (r1 & PAR_ERR)
 305				uap->port.icount.parity++;
 306			else if (r1 & CRC_ERR)
 307				uap->port.icount.frame++;
 308			if (r1 & Rx_OVR)
 309				uap->port.icount.overrun++;
 310			r1 &= uap->port.read_status_mask;
 311			if (r1 & BRK_ABRT)
 312				flag = TTY_BREAK;
 313			else if (r1 & PAR_ERR)
 314				flag = TTY_PARITY;
 315			else if (r1 & CRC_ERR)
 316				flag = TTY_FRAME;
 317		}
 318
 319		if (uap->port.ignore_status_mask == 0xff ||
 320		    (r1 & uap->port.ignore_status_mask) == 0) {
 321			tty_insert_flip_char(tty, ch, flag);
 322		}
 323		if (r1 & Rx_OVR)
 324			tty_insert_flip_char(tty, 0, TTY_OVERRUN);
 325	next_char:
 326		/* We can get stuck in an infinite loop getting char 0 when the
 327		 * line is in a wrong HW state, we break that here.
 328		 * When that happens, I disable the receive side of the driver.
 329		 * Note that what I've been experiencing is a real irq loop where
 330		 * I'm getting flooded regardless of the actual port speed.
 331		 * Something strange is going on with the HW
 332		 */
 333		if ((++loops) > 1000)
 334			goto flood;
 335		ch = read_zsreg(uap, R0);
 336		if (!(ch & Rx_CH_AV))
 337			break;
 338	}
 339
 340	return tty;
 341 flood:
 342	uap->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
 343	write_zsreg(uap, R1, uap->curregs[R1]);
 344	zssync(uap);
 345	pmz_error("pmz: rx irq flood !\n");
 346	return tty;
 347}
 348
 349static void pmz_status_handle(struct uart_pmac_port *uap)
 350{
 351	unsigned char status;
 352
 353	status = read_zsreg(uap, R0);
 354	write_zsreg(uap, R0, RES_EXT_INT);
 355	zssync(uap);
 356
 357	if (ZS_IS_OPEN(uap) && ZS_WANTS_MODEM_STATUS(uap)) {
 358		if (status & SYNC_HUNT)
 359			uap->port.icount.dsr++;
 360
 361		/* The Zilog just gives us an interrupt when DCD/CTS/etc. change.
 362		 * But it does not tell us which bit has changed, we have to keep
 363		 * track of this ourselves.
 364		 * The CTS input is inverted for some reason.  -- paulus
 365		 */
 366		if ((status ^ uap->prev_status) & DCD)
 367			uart_handle_dcd_change(&uap->port,
 368					       (status & DCD));
 369		if ((status ^ uap->prev_status) & CTS)
 370			uart_handle_cts_change(&uap->port,
 371					       !(status & CTS));
 372
 373		wake_up_interruptible(&uap->port.state->port.delta_msr_wait);
 374	}
 375
 376	if (status & BRK_ABRT)
 377		uap->flags |= PMACZILOG_FLAG_BREAK;
 378
 379	uap->prev_status = status;
 380}
 381
 382static void pmz_transmit_chars(struct uart_pmac_port *uap)
 383{
 384	struct circ_buf *xmit;
 385
 386	if (ZS_IS_ASLEEP(uap))
 387		return;
 388	if (ZS_IS_CONS(uap)) {
 389		unsigned char status = read_zsreg(uap, R0);
 390
 391		/* TX still busy?  Just wait for the next TX done interrupt.
 392		 *
 393		 * It can occur because of how we do serial console writes.  It would
 394		 * be nice to transmit console writes just like we normally would for
 395		 * a TTY line. (ie. buffered and TX interrupt driven).  That is not
 396		 * easy because console writes cannot sleep.  One solution might be
 397		 * to poll on enough port->xmit space becoming free.  -DaveM
 398		 */
 399		if (!(status & Tx_BUF_EMP))
 400			return;
 401	}
 402
 403	uap->flags &= ~PMACZILOG_FLAG_TX_ACTIVE;
 404
 405	if (ZS_REGS_HELD(uap)) {
 406		pmz_load_zsregs(uap, uap->curregs);
 407		uap->flags &= ~PMACZILOG_FLAG_REGS_HELD;
 408	}
 409
 410	if (ZS_TX_STOPPED(uap)) {
 411		uap->flags &= ~PMACZILOG_FLAG_TX_STOPPED;
 412		goto ack_tx_int;
 413	}
 414
 415	/* Under some circumstances, we see interrupts reported for
 416	 * a closed channel. The interrupt mask in R1 is clear, but
 417	 * R3 still signals the interrupts and we see them when taking
 418	 * an interrupt for the other channel (this could be a qemu
 419	 * bug but since the ESCC doc doesn't specify precsiely whether
 420	 * R3 interrup status bits are masked by R1 interrupt enable
 421	 * bits, better safe than sorry). --BenH.
 422	 */
 423	if (!ZS_IS_OPEN(uap))
 424		goto ack_tx_int;
 425
 426	if (uap->port.x_char) {
 427		uap->flags |= PMACZILOG_FLAG_TX_ACTIVE;
 428		write_zsdata(uap, uap->port.x_char);
 429		zssync(uap);
 430		uap->port.icount.tx++;
 431		uap->port.x_char = 0;
 432		return;
 433	}
 434
 435	if (uap->port.state == NULL)
 436		goto ack_tx_int;
 437	xmit = &uap->port.state->xmit;
 438	if (uart_circ_empty(xmit)) {
 439		uart_write_wakeup(&uap->port);
 440		goto ack_tx_int;
 441	}
 442	if (uart_tx_stopped(&uap->port))
 443		goto ack_tx_int;
 444
 445	uap->flags |= PMACZILOG_FLAG_TX_ACTIVE;
 446	write_zsdata(uap, xmit->buf[xmit->tail]);
 447	zssync(uap);
 448
 449	xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
 450	uap->port.icount.tx++;
 451
 452	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 453		uart_write_wakeup(&uap->port);
 454
 455	return;
 456
 457ack_tx_int:
 458	write_zsreg(uap, R0, RES_Tx_P);
 459	zssync(uap);
 460}
 461
 462/* Hrm... we register that twice, fixme later.... */
 463static irqreturn_t pmz_interrupt(int irq, void *dev_id)
 464{
 465	struct uart_pmac_port *uap = dev_id;
 466	struct uart_pmac_port *uap_a;
 467	struct uart_pmac_port *uap_b;
 468	int rc = IRQ_NONE;
 469	struct tty_struct *tty;
 470	u8 r3;
 471
 472	uap_a = pmz_get_port_A(uap);
 473	uap_b = uap_a->mate;
 474
 475	spin_lock(&uap_a->port.lock);
 476	r3 = read_zsreg(uap_a, R3);
 477
 478#ifdef DEBUG_HARD
 479	pmz_debug("irq, r3: %x\n", r3);
 480#endif
 481	/* Channel A */
 482	tty = NULL;
 483	if (r3 & (CHAEXT | CHATxIP | CHARxIP)) {
 
 
 
 
 484		write_zsreg(uap_a, R0, RES_H_IUS);
 485		zssync(uap_a);		
 486		if (r3 & CHAEXT)
 487			pmz_status_handle(uap_a);
 488		if (r3 & CHARxIP)
 489			tty = pmz_receive_chars(uap_a);
 490		if (r3 & CHATxIP)
 491			pmz_transmit_chars(uap_a);
 492		rc = IRQ_HANDLED;
 493	}
 
 494	spin_unlock(&uap_a->port.lock);
 495	if (tty != NULL)
 496		tty_flip_buffer_push(tty);
 497
 498	if (uap_b->node == NULL)
 499		goto out;
 500
 501	spin_lock(&uap_b->port.lock);
 502	tty = NULL;
 503	if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) {
 
 
 
 
 504		write_zsreg(uap_b, R0, RES_H_IUS);
 505		zssync(uap_b);
 506		if (r3 & CHBEXT)
 507			pmz_status_handle(uap_b);
 508		if (r3 & CHBRxIP)
 509			tty = pmz_receive_chars(uap_b);
 510		if (r3 & CHBTxIP)
 511			pmz_transmit_chars(uap_b);
 512		rc = IRQ_HANDLED;
 513	}
 
 514	spin_unlock(&uap_b->port.lock);
 515	if (tty != NULL)
 516		tty_flip_buffer_push(tty);
 517
 518 out:
 519#ifdef DEBUG_HARD
 520	pmz_debug("irq done.\n");
 521#endif
 522	return rc;
 523}
 524
 525/*
 526 * Peek the status register, lock not held by caller
 527 */
 528static inline u8 pmz_peek_status(struct uart_pmac_port *uap)
 529{
 530	unsigned long flags;
 531	u8 status;
 532	
 533	spin_lock_irqsave(&uap->port.lock, flags);
 534	status = read_zsreg(uap, R0);
 535	spin_unlock_irqrestore(&uap->port.lock, flags);
 536
 537	return status;
 538}
 539
 540/* 
 541 * Check if transmitter is empty
 542 * The port lock is not held.
 543 */
 544static unsigned int pmz_tx_empty(struct uart_port *port)
 545{
 546	struct uart_pmac_port *uap = to_pmz(port);
 547	unsigned char status;
 548
 549	if (ZS_IS_ASLEEP(uap) || uap->node == NULL)
 550		return TIOCSER_TEMT;
 551
 552	status = pmz_peek_status(to_pmz(port));
 553	if (status & Tx_BUF_EMP)
 554		return TIOCSER_TEMT;
 555	return 0;
 556}
 557
 558/* 
 559 * Set Modem Control (RTS & DTR) bits
 560 * The port lock is held and interrupts are disabled.
 561 * Note: Shall we really filter out RTS on external ports or
 562 * should that be dealt at higher level only ?
 563 */
 564static void pmz_set_mctrl(struct uart_port *port, unsigned int mctrl)
 565{
 566	struct uart_pmac_port *uap = to_pmz(port);
 567	unsigned char set_bits, clear_bits;
 568
 569        /* Do nothing for irda for now... */
 570	if (ZS_IS_IRDA(uap))
 571		return;
 572	/* We get called during boot with a port not up yet */
 573	if (ZS_IS_ASLEEP(uap) ||
 574	    !(ZS_IS_OPEN(uap) || ZS_IS_CONS(uap)))
 575		return;
 576
 577	set_bits = clear_bits = 0;
 578
 579	if (ZS_IS_INTMODEM(uap)) {
 580		if (mctrl & TIOCM_RTS)
 581			set_bits |= RTS;
 582		else
 583			clear_bits |= RTS;
 584	}
 585	if (mctrl & TIOCM_DTR)
 586		set_bits |= DTR;
 587	else
 588		clear_bits |= DTR;
 589
 590	/* NOTE: Not subject to 'transmitter active' rule.  */ 
 591	uap->curregs[R5] |= set_bits;
 592	uap->curregs[R5] &= ~clear_bits;
 593	if (ZS_IS_ASLEEP(uap))
 594		return;
 595	write_zsreg(uap, R5, uap->curregs[R5]);
 596	pmz_debug("pmz_set_mctrl: set bits: %x, clear bits: %x -> %x\n",
 597		  set_bits, clear_bits, uap->curregs[R5]);
 598	zssync(uap);
 599}
 600
 601/* 
 602 * Get Modem Control bits (only the input ones, the core will
 603 * or that with a cached value of the control ones)
 604 * The port lock is held and interrupts are disabled.
 605 */
 606static unsigned int pmz_get_mctrl(struct uart_port *port)
 607{
 608	struct uart_pmac_port *uap = to_pmz(port);
 609	unsigned char status;
 610	unsigned int ret;
 611
 612	if (ZS_IS_ASLEEP(uap) || uap->node == NULL)
 613		return 0;
 614
 615	status = read_zsreg(uap, R0);
 616
 617	ret = 0;
 618	if (status & DCD)
 619		ret |= TIOCM_CAR;
 620	if (status & SYNC_HUNT)
 621		ret |= TIOCM_DSR;
 622	if (!(status & CTS))
 623		ret |= TIOCM_CTS;
 624
 625	return ret;
 626}
 627
 628/* 
 629 * Stop TX side. Dealt like sunzilog at next Tx interrupt,
 630 * though for DMA, we will have to do a bit more.
 631 * The port lock is held and interrupts are disabled.
 632 */
 633static void pmz_stop_tx(struct uart_port *port)
 634{
 635	to_pmz(port)->flags |= PMACZILOG_FLAG_TX_STOPPED;
 636}
 637
 638/* 
 639 * Kick the Tx side.
 640 * The port lock is held and interrupts are disabled.
 641 */
 642static void pmz_start_tx(struct uart_port *port)
 643{
 644	struct uart_pmac_port *uap = to_pmz(port);
 645	unsigned char status;
 646
 647	pmz_debug("pmz: start_tx()\n");
 648
 649	uap->flags |= PMACZILOG_FLAG_TX_ACTIVE;
 650	uap->flags &= ~PMACZILOG_FLAG_TX_STOPPED;
 651
 652	if (ZS_IS_ASLEEP(uap) || uap->node == NULL)
 653		return;
 654
 655	status = read_zsreg(uap, R0);
 656
 657	/* TX busy?  Just wait for the TX done interrupt.  */
 658	if (!(status & Tx_BUF_EMP))
 659		return;
 660
 661	/* Send the first character to jump-start the TX done
 662	 * IRQ sending engine.
 663	 */
 664	if (port->x_char) {
 665		write_zsdata(uap, port->x_char);
 666		zssync(uap);
 667		port->icount.tx++;
 668		port->x_char = 0;
 669	} else {
 670		struct circ_buf *xmit = &port->state->xmit;
 671
 672		write_zsdata(uap, xmit->buf[xmit->tail]);
 673		zssync(uap);
 674		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
 675		port->icount.tx++;
 676
 677		if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 678			uart_write_wakeup(&uap->port);
 679	}
 680	pmz_debug("pmz: start_tx() done.\n");
 681}
 682
 683/* 
 684 * Stop Rx side, basically disable emitting of
 685 * Rx interrupts on the port. We don't disable the rx
 686 * side of the chip proper though
 687 * The port lock is held.
 688 */
 689static void pmz_stop_rx(struct uart_port *port)
 690{
 691	struct uart_pmac_port *uap = to_pmz(port);
 692
 693	if (ZS_IS_ASLEEP(uap) || uap->node == NULL)
 694		return;
 695
 696	pmz_debug("pmz: stop_rx()()\n");
 697
 698	/* Disable all RX interrupts.  */
 699	uap->curregs[R1] &= ~RxINT_MASK;
 700	pmz_maybe_update_regs(uap);
 701
 702	pmz_debug("pmz: stop_rx() done.\n");
 703}
 704
 705/* 
 706 * Enable modem status change interrupts
 707 * The port lock is held.
 708 */
 709static void pmz_enable_ms(struct uart_port *port)
 710{
 711	struct uart_pmac_port *uap = to_pmz(port);
 712	unsigned char new_reg;
 713
 714	if (ZS_IS_IRDA(uap) || uap->node == NULL)
 715		return;
 716	new_reg = uap->curregs[R15] | (DCDIE | SYNCIE | CTSIE);
 717	if (new_reg != uap->curregs[R15]) {
 718		uap->curregs[R15] = new_reg;
 719
 720		if (ZS_IS_ASLEEP(uap))
 721			return;
 722		/* NOTE: Not subject to 'transmitter active' rule. */
 723		write_zsreg(uap, R15, uap->curregs[R15]);
 724	}
 725}
 726
 727/* 
 728 * Control break state emission
 729 * The port lock is not held.
 730 */
 731static void pmz_break_ctl(struct uart_port *port, int break_state)
 732{
 733	struct uart_pmac_port *uap = to_pmz(port);
 734	unsigned char set_bits, clear_bits, new_reg;
 735	unsigned long flags;
 736
 737	if (uap->node == NULL)
 738		return;
 739	set_bits = clear_bits = 0;
 740
 741	if (break_state)
 742		set_bits |= SND_BRK;
 743	else
 744		clear_bits |= SND_BRK;
 745
 746	spin_lock_irqsave(&port->lock, flags);
 747
 748	new_reg = (uap->curregs[R5] | set_bits) & ~clear_bits;
 749	if (new_reg != uap->curregs[R5]) {
 750		uap->curregs[R5] = new_reg;
 751
 752		/* NOTE: Not subject to 'transmitter active' rule. */
 753		if (ZS_IS_ASLEEP(uap)) {
 754			spin_unlock_irqrestore(&port->lock, flags);
 755			return;
 756		}
 757		write_zsreg(uap, R5, uap->curregs[R5]);
 758	}
 759
 760	spin_unlock_irqrestore(&port->lock, flags);
 761}
 762
 763#ifdef CONFIG_PPC_PMAC
 764
 765/*
 766 * Turn power on or off to the SCC and associated stuff
 767 * (port drivers, modem, IR port, etc.)
 768 * Returns the number of milliseconds we should wait before
 769 * trying to use the port.
 770 */
 771static int pmz_set_scc_power(struct uart_pmac_port *uap, int state)
 772{
 773	int delay = 0;
 774	int rc;
 775
 776	if (state) {
 777		rc = pmac_call_feature(
 778			PMAC_FTR_SCC_ENABLE, uap->node, uap->port_type, 1);
 779		pmz_debug("port power on result: %d\n", rc);
 780		if (ZS_IS_INTMODEM(uap)) {
 781			rc = pmac_call_feature(
 782				PMAC_FTR_MODEM_ENABLE, uap->node, 0, 1);
 783			delay = 2500;	/* wait for 2.5s before using */
 784			pmz_debug("modem power result: %d\n", rc);
 785		}
 786	} else {
 787		/* TODO: Make that depend on a timer, don't power down
 788		 * immediately
 789		 */
 790		if (ZS_IS_INTMODEM(uap)) {
 791			rc = pmac_call_feature(
 792				PMAC_FTR_MODEM_ENABLE, uap->node, 0, 0);
 793			pmz_debug("port power off result: %d\n", rc);
 794		}
 795		pmac_call_feature(PMAC_FTR_SCC_ENABLE, uap->node, uap->port_type, 0);
 796	}
 797	return delay;
 798}
 799
 800#else
 801
 802static int pmz_set_scc_power(struct uart_pmac_port *uap, int state)
 803{
 804	return 0;
 805}
 806
 807#endif /* !CONFIG_PPC_PMAC */
 808
 809/*
 810 * FixZeroBug....Works around a bug in the SCC receiving channel.
 811 * Inspired from Darwin code, 15 Sept. 2000  -DanM
 812 *
 813 * The following sequence prevents a problem that is seen with O'Hare ASICs
 814 * (most versions -- also with some Heathrow and Hydra ASICs) where a zero
 815 * at the input to the receiver becomes 'stuck' and locks up the receiver.
 816 * This problem can occur as a result of a zero bit at the receiver input
 817 * coincident with any of the following events:
 818 *
 819 *	The SCC is initialized (hardware or software).
 820 *	A framing error is detected.
 821 *	The clocking option changes from synchronous or X1 asynchronous
 822 *		clocking to X16, X32, or X64 asynchronous clocking.
 823 *	The decoding mode is changed among NRZ, NRZI, FM0, or FM1.
 824 *
 825 * This workaround attempts to recover from the lockup condition by placing
 826 * the SCC in synchronous loopback mode with a fast clock before programming
 827 * any of the asynchronous modes.
 828 */
 829static void pmz_fix_zero_bug_scc(struct uart_pmac_port *uap)
 830{
 831	write_zsreg(uap, 9, ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB);
 832	zssync(uap);
 833	udelay(10);
 834	write_zsreg(uap, 9, (ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB) | NV);
 835	zssync(uap);
 836
 837	write_zsreg(uap, 4, X1CLK | MONSYNC);
 838	write_zsreg(uap, 3, Rx8);
 839	write_zsreg(uap, 5, Tx8 | RTS);
 840	write_zsreg(uap, 9, NV);	/* Didn't we already do this? */
 841	write_zsreg(uap, 11, RCBR | TCBR);
 842	write_zsreg(uap, 12, 0);
 843	write_zsreg(uap, 13, 0);
 844	write_zsreg(uap, 14, (LOOPBAK | BRSRC));
 845	write_zsreg(uap, 14, (LOOPBAK | BRSRC | BRENAB));
 846	write_zsreg(uap, 3, Rx8 | RxENABLE);
 847	write_zsreg(uap, 0, RES_EXT_INT);
 848	write_zsreg(uap, 0, RES_EXT_INT);
 849	write_zsreg(uap, 0, RES_EXT_INT);	/* to kill some time */
 850
 851	/* The channel should be OK now, but it is probably receiving
 852	 * loopback garbage.
 853	 * Switch to asynchronous mode, disable the receiver,
 854	 * and discard everything in the receive buffer.
 855	 */
 856	write_zsreg(uap, 9, NV);
 857	write_zsreg(uap, 4, X16CLK | SB_MASK);
 858	write_zsreg(uap, 3, Rx8);
 859
 860	while (read_zsreg(uap, 0) & Rx_CH_AV) {
 861		(void)read_zsreg(uap, 8);
 862		write_zsreg(uap, 0, RES_EXT_INT);
 863		write_zsreg(uap, 0, ERR_RES);
 864	}
 865}
 866
 867/*
 868 * Real startup routine, powers up the hardware and sets up
 869 * the SCC. Returns a delay in ms where you need to wait before
 870 * actually using the port, this is typically the internal modem
 871 * powerup delay. This routine expect the lock to be taken.
 872 */
 873static int __pmz_startup(struct uart_pmac_port *uap)
 874{
 875	int pwr_delay = 0;
 876
 877	memset(&uap->curregs, 0, sizeof(uap->curregs));
 878
 879	/* Power up the SCC & underlying hardware (modem/irda) */
 880	pwr_delay = pmz_set_scc_power(uap, 1);
 881
 882	/* Nice buggy HW ... */
 883	pmz_fix_zero_bug_scc(uap);
 884
 885	/* Reset the channel */
 886	uap->curregs[R9] = 0;
 887	write_zsreg(uap, 9, ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB);
 888	zssync(uap);
 889	udelay(10);
 890	write_zsreg(uap, 9, 0);
 891	zssync(uap);
 892
 893	/* Clear the interrupt registers */
 894	write_zsreg(uap, R1, 0);
 895	write_zsreg(uap, R0, ERR_RES);
 896	write_zsreg(uap, R0, ERR_RES);
 897	write_zsreg(uap, R0, RES_H_IUS);
 898	write_zsreg(uap, R0, RES_H_IUS);
 899
 900	/* Setup some valid baud rate */
 901	uap->curregs[R4] = X16CLK | SB1;
 902	uap->curregs[R3] = Rx8;
 903	uap->curregs[R5] = Tx8 | RTS;
 904	if (!ZS_IS_IRDA(uap))
 905		uap->curregs[R5] |= DTR;
 906	uap->curregs[R12] = 0;
 907	uap->curregs[R13] = 0;
 908	uap->curregs[R14] = BRENAB;
 909
 910	/* Clear handshaking, enable BREAK interrupts */
 911	uap->curregs[R15] = BRKIE;
 912
 913	/* Master interrupt enable */
 914	uap->curregs[R9] |= NV | MIE;
 915
 916	pmz_load_zsregs(uap, uap->curregs);
 917
 918	/* Enable receiver and transmitter.  */
 919	write_zsreg(uap, R3, uap->curregs[R3] |= RxENABLE);
 920	write_zsreg(uap, R5, uap->curregs[R5] |= TxENABLE);
 921
 922	/* Remember status for DCD/CTS changes */
 923	uap->prev_status = read_zsreg(uap, R0);
 924
 925	return pwr_delay;
 926}
 927
 928static void pmz_irda_reset(struct uart_pmac_port *uap)
 929{
 
 
 
 930	uap->curregs[R5] |= DTR;
 931	write_zsreg(uap, R5, uap->curregs[R5]);
 932	zssync(uap);
 933	mdelay(110);
 
 
 
 934	uap->curregs[R5] &= ~DTR;
 935	write_zsreg(uap, R5, uap->curregs[R5]);
 936	zssync(uap);
 937	mdelay(10);
 
 938}
 939
 940/*
 941 * This is the "normal" startup routine, using the above one
 942 * wrapped with the lock and doing a schedule delay
 943 */
 944static int pmz_startup(struct uart_port *port)
 945{
 946	struct uart_pmac_port *uap = to_pmz(port);
 947	unsigned long flags;
 948	int pwr_delay = 0;
 949
 950	pmz_debug("pmz: startup()\n");
 951
 952	if (ZS_IS_ASLEEP(uap))
 953		return -EAGAIN;
 954	if (uap->node == NULL)
 955		return -ENODEV;
 956
 957	mutex_lock(&pmz_irq_mutex);
 958
 959	uap->flags |= PMACZILOG_FLAG_IS_OPEN;
 960
 961	/* A console is never powered down. Else, power up and
 962	 * initialize the chip
 963	 */
 964	if (!ZS_IS_CONS(uap)) {
 965		spin_lock_irqsave(&port->lock, flags);
 966		pwr_delay = __pmz_startup(uap);
 967		spin_unlock_irqrestore(&port->lock, flags);
 968	}	
 969
 970	pmz_get_port_A(uap)->flags |= PMACZILOG_FLAG_IS_IRQ_ON;
 971	if (request_irq(uap->port.irq, pmz_interrupt, IRQF_SHARED,
 972			"SCC", uap)) {
 973		pmz_error("Unable to register zs interrupt handler.\n");
 974		pmz_set_scc_power(uap, 0);
 975		mutex_unlock(&pmz_irq_mutex);
 976		return -ENXIO;
 977	}
 978
 979	mutex_unlock(&pmz_irq_mutex);
 980
 981	/* Right now, we deal with delay by blocking here, I'll be
 982	 * smarter later on
 983	 */
 984	if (pwr_delay != 0) {
 985		pmz_debug("pmz: delaying %d ms\n", pwr_delay);
 986		msleep(pwr_delay);
 987	}
 988
 989	/* IrDA reset is done now */
 990	if (ZS_IS_IRDA(uap))
 991		pmz_irda_reset(uap);
 992
 993	/* Enable interrupts emission from the chip */
 994	spin_lock_irqsave(&port->lock, flags);
 995	uap->curregs[R1] |= INT_ALL_Rx | TxINT_ENAB;
 996	if (!ZS_IS_EXTCLK(uap))
 997		uap->curregs[R1] |= EXT_INT_ENAB;
 998	write_zsreg(uap, R1, uap->curregs[R1]);
 999	spin_unlock_irqrestore(&port->lock, flags);
1000
1001	pmz_debug("pmz: startup() done.\n");
1002
1003	return 0;
1004}
1005
1006static void pmz_shutdown(struct uart_port *port)
1007{
1008	struct uart_pmac_port *uap = to_pmz(port);
1009	unsigned long flags;
1010
1011	pmz_debug("pmz: shutdown()\n");
1012
1013	if (uap->node == NULL)
1014		return;
1015
1016	mutex_lock(&pmz_irq_mutex);
1017
1018	/* Release interrupt handler */
1019	free_irq(uap->port.irq, uap);
1020
1021	spin_lock_irqsave(&port->lock, flags);
1022
1023	uap->flags &= ~PMACZILOG_FLAG_IS_OPEN;
 
1024
1025	if (!ZS_IS_OPEN(uap->mate))
1026		pmz_get_port_A(uap)->flags &= ~PMACZILOG_FLAG_IS_IRQ_ON;
 
 
1027
1028	/* Disable interrupts */
1029	if (!ZS_IS_ASLEEP(uap)) {
1030		uap->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
1031		write_zsreg(uap, R1, uap->curregs[R1]);
1032		zssync(uap);
1033	}
1034
1035	if (ZS_IS_CONS(uap) || ZS_IS_ASLEEP(uap)) {
1036		spin_unlock_irqrestore(&port->lock, flags);
1037		mutex_unlock(&pmz_irq_mutex);
1038		return;
1039	}
1040
1041	/* Disable receiver and transmitter.  */
1042	uap->curregs[R3] &= ~RxENABLE;
1043	uap->curregs[R5] &= ~TxENABLE;
1044
1045	/* Disable all interrupts and BRK assertion.  */
1046	uap->curregs[R5] &= ~SND_BRK;
1047	pmz_maybe_update_regs(uap);
1048
1049	/* Shut the chip down */
1050	pmz_set_scc_power(uap, 0);
1051
1052	spin_unlock_irqrestore(&port->lock, flags);
 
1053
1054	mutex_unlock(&pmz_irq_mutex);
1055
1056	pmz_debug("pmz: shutdown() done.\n");
1057}
1058
1059/* Shared by TTY driver and serial console setup.  The port lock is held
1060 * and local interrupts are disabled.
1061 */
1062static void pmz_convert_to_zs(struct uart_pmac_port *uap, unsigned int cflag,
1063			      unsigned int iflag, unsigned long baud)
1064{
1065	int brg;
1066
1067	/* Switch to external clocking for IrDA high clock rates. That
1068	 * code could be re-used for Midi interfaces with different
1069	 * multipliers
1070	 */
1071	if (baud >= 115200 && ZS_IS_IRDA(uap)) {
1072		uap->curregs[R4] = X1CLK;
1073		uap->curregs[R11] = RCTRxCP | TCTRxCP;
1074		uap->curregs[R14] = 0; /* BRG off */
1075		uap->curregs[R12] = 0;
1076		uap->curregs[R13] = 0;
1077		uap->flags |= PMACZILOG_FLAG_IS_EXTCLK;
1078	} else {
1079		switch (baud) {
1080		case ZS_CLOCK/16:	/* 230400 */
1081			uap->curregs[R4] = X16CLK;
1082			uap->curregs[R11] = 0;
1083			uap->curregs[R14] = 0;
1084			break;
1085		case ZS_CLOCK/32:	/* 115200 */
1086			uap->curregs[R4] = X32CLK;
1087			uap->curregs[R11] = 0;
1088			uap->curregs[R14] = 0;
1089			break;
1090		default:
1091			uap->curregs[R4] = X16CLK;
1092			uap->curregs[R11] = TCBR | RCBR;
1093			brg = BPS_TO_BRG(baud, ZS_CLOCK / 16);
1094			uap->curregs[R12] = (brg & 255);
1095			uap->curregs[R13] = ((brg >> 8) & 255);
1096			uap->curregs[R14] = BRENAB;
1097		}
1098		uap->flags &= ~PMACZILOG_FLAG_IS_EXTCLK;
1099	}
1100
1101	/* Character size, stop bits, and parity. */
1102	uap->curregs[3] &= ~RxN_MASK;
1103	uap->curregs[5] &= ~TxN_MASK;
1104
1105	switch (cflag & CSIZE) {
1106	case CS5:
1107		uap->curregs[3] |= Rx5;
1108		uap->curregs[5] |= Tx5;
1109		uap->parity_mask = 0x1f;
1110		break;
1111	case CS6:
1112		uap->curregs[3] |= Rx6;
1113		uap->curregs[5] |= Tx6;
1114		uap->parity_mask = 0x3f;
1115		break;
1116	case CS7:
1117		uap->curregs[3] |= Rx7;
1118		uap->curregs[5] |= Tx7;
1119		uap->parity_mask = 0x7f;
1120		break;
1121	case CS8:
1122	default:
1123		uap->curregs[3] |= Rx8;
1124		uap->curregs[5] |= Tx8;
1125		uap->parity_mask = 0xff;
1126		break;
1127	};
1128	uap->curregs[4] &= ~(SB_MASK);
1129	if (cflag & CSTOPB)
1130		uap->curregs[4] |= SB2;
1131	else
1132		uap->curregs[4] |= SB1;
1133	if (cflag & PARENB)
1134		uap->curregs[4] |= PAR_ENAB;
1135	else
1136		uap->curregs[4] &= ~PAR_ENAB;
1137	if (!(cflag & PARODD))
1138		uap->curregs[4] |= PAR_EVEN;
1139	else
1140		uap->curregs[4] &= ~PAR_EVEN;
1141
1142	uap->port.read_status_mask = Rx_OVR;
1143	if (iflag & INPCK)
1144		uap->port.read_status_mask |= CRC_ERR | PAR_ERR;
1145	if (iflag & (BRKINT | PARMRK))
1146		uap->port.read_status_mask |= BRK_ABRT;
1147
1148	uap->port.ignore_status_mask = 0;
1149	if (iflag & IGNPAR)
1150		uap->port.ignore_status_mask |= CRC_ERR | PAR_ERR;
1151	if (iflag & IGNBRK) {
1152		uap->port.ignore_status_mask |= BRK_ABRT;
1153		if (iflag & IGNPAR)
1154			uap->port.ignore_status_mask |= Rx_OVR;
1155	}
1156
1157	if ((cflag & CREAD) == 0)
1158		uap->port.ignore_status_mask = 0xff;
1159}
1160
1161
1162/*
1163 * Set the irda codec on the imac to the specified baud rate.
1164 */
1165static void pmz_irda_setup(struct uart_pmac_port *uap, unsigned long *baud)
1166{
1167	u8 cmdbyte;
1168	int t, version;
1169
1170	switch (*baud) {
1171	/* SIR modes */
1172	case 2400:
1173		cmdbyte = 0x53;
1174		break;
1175	case 4800:
1176		cmdbyte = 0x52;
1177		break;
1178	case 9600:
1179		cmdbyte = 0x51;
1180		break;
1181	case 19200:
1182		cmdbyte = 0x50;
1183		break;
1184	case 38400:
1185		cmdbyte = 0x4f;
1186		break;
1187	case 57600:
1188		cmdbyte = 0x4e;
1189		break;
1190	case 115200:
1191		cmdbyte = 0x4d;
1192		break;
1193	/* The FIR modes aren't really supported at this point, how
1194	 * do we select the speed ? via the FCR on KeyLargo ?
1195	 */
1196	case 1152000:
1197		cmdbyte = 0;
1198		break;
1199	case 4000000:
1200		cmdbyte = 0;
1201		break;
1202	default: /* 9600 */
1203		cmdbyte = 0x51;
1204		*baud = 9600;
1205		break;
1206	}
1207
1208	/* Wait for transmitter to drain */
1209	t = 10000;
1210	while ((read_zsreg(uap, R0) & Tx_BUF_EMP) == 0
1211	       || (read_zsreg(uap, R1) & ALL_SNT) == 0) {
1212		if (--t <= 0) {
1213			pmz_error("transmitter didn't drain\n");
1214			return;
1215		}
1216		udelay(10);
1217	}
1218
1219	/* Drain the receiver too */
1220	t = 100;
1221	(void)read_zsdata(uap);
1222	(void)read_zsdata(uap);
1223	(void)read_zsdata(uap);
1224	mdelay(10);
1225	while (read_zsreg(uap, R0) & Rx_CH_AV) {
1226		read_zsdata(uap);
1227		mdelay(10);
1228		if (--t <= 0) {
1229			pmz_error("receiver didn't drain\n");
1230			return;
1231		}
1232	}
1233
1234	/* Switch to command mode */
1235	uap->curregs[R5] |= DTR;
1236	write_zsreg(uap, R5, uap->curregs[R5]);
1237	zssync(uap);
1238	mdelay(1);
1239
1240	/* Switch SCC to 19200 */
1241	pmz_convert_to_zs(uap, CS8, 0, 19200);		
1242	pmz_load_zsregs(uap, uap->curregs);
1243	mdelay(1);
1244
1245	/* Write get_version command byte */
1246	write_zsdata(uap, 1);
1247	t = 5000;
1248	while ((read_zsreg(uap, R0) & Rx_CH_AV) == 0) {
1249		if (--t <= 0) {
1250			pmz_error("irda_setup timed out on get_version byte\n");
1251			goto out;
1252		}
1253		udelay(10);
1254	}
1255	version = read_zsdata(uap);
1256
1257	if (version < 4) {
1258		pmz_info("IrDA: dongle version %d not supported\n", version);
1259		goto out;
1260	}
1261
1262	/* Send speed mode */
1263	write_zsdata(uap, cmdbyte);
1264	t = 5000;
1265	while ((read_zsreg(uap, R0) & Rx_CH_AV) == 0) {
1266		if (--t <= 0) {
1267			pmz_error("irda_setup timed out on speed mode byte\n");
1268			goto out;
1269		}
1270		udelay(10);
1271	}
1272	t = read_zsdata(uap);
1273	if (t != cmdbyte)
1274		pmz_error("irda_setup speed mode byte = %x (%x)\n", t, cmdbyte);
1275
1276	pmz_info("IrDA setup for %ld bps, dongle version: %d\n",
1277		 *baud, version);
1278
1279	(void)read_zsdata(uap);
1280	(void)read_zsdata(uap);
1281	(void)read_zsdata(uap);
1282
1283 out:
1284	/* Switch back to data mode */
1285	uap->curregs[R5] &= ~DTR;
1286	write_zsreg(uap, R5, uap->curregs[R5]);
1287	zssync(uap);
1288
1289	(void)read_zsdata(uap);
1290	(void)read_zsdata(uap);
1291	(void)read_zsdata(uap);
1292}
1293
1294
1295static void __pmz_set_termios(struct uart_port *port, struct ktermios *termios,
1296			      struct ktermios *old)
1297{
1298	struct uart_pmac_port *uap = to_pmz(port);
1299	unsigned long baud;
1300
1301	pmz_debug("pmz: set_termios()\n");
1302
1303	if (ZS_IS_ASLEEP(uap))
1304		return;
1305
1306	memcpy(&uap->termios_cache, termios, sizeof(struct ktermios));
1307
1308	/* XXX Check which revs of machines actually allow 1 and 4Mb speeds
1309	 * on the IR dongle. Note that the IRTTY driver currently doesn't know
1310	 * about the FIR mode and high speed modes. So these are unused. For
1311	 * implementing proper support for these, we should probably add some
1312	 * DMA as well, at least on the Rx side, which isn't a simple thing
1313	 * at this point.
1314	 */
1315	if (ZS_IS_IRDA(uap)) {
1316		/* Calc baud rate */
1317		baud = uart_get_baud_rate(port, termios, old, 1200, 4000000);
1318		pmz_debug("pmz: switch IRDA to %ld bauds\n", baud);
1319		/* Cet the irda codec to the right rate */
1320		pmz_irda_setup(uap, &baud);
1321		/* Set final baud rate */
1322		pmz_convert_to_zs(uap, termios->c_cflag, termios->c_iflag, baud);
1323		pmz_load_zsregs(uap, uap->curregs);
1324		zssync(uap);
1325	} else {
1326		baud = uart_get_baud_rate(port, termios, old, 1200, 230400);
1327		pmz_convert_to_zs(uap, termios->c_cflag, termios->c_iflag, baud);
1328		/* Make sure modem status interrupts are correctly configured */
1329		if (UART_ENABLE_MS(&uap->port, termios->c_cflag)) {
1330			uap->curregs[R15] |= DCDIE | SYNCIE | CTSIE;
1331			uap->flags |= PMACZILOG_FLAG_MODEM_STATUS;
1332		} else {
1333			uap->curregs[R15] &= ~(DCDIE | SYNCIE | CTSIE);
1334			uap->flags &= ~PMACZILOG_FLAG_MODEM_STATUS;
1335		}
1336
1337		/* Load registers to the chip */
1338		pmz_maybe_update_regs(uap);
1339	}
1340	uart_update_timeout(port, termios->c_cflag, baud);
1341
1342	pmz_debug("pmz: set_termios() done.\n");
1343}
1344
1345/* The port lock is not held.  */
1346static void pmz_set_termios(struct uart_port *port, struct ktermios *termios,
1347			    struct ktermios *old)
1348{
1349	struct uart_pmac_port *uap = to_pmz(port);
1350	unsigned long flags;
1351
1352	spin_lock_irqsave(&port->lock, flags);	
1353
1354	/* Disable IRQs on the port */
1355	uap->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
1356	write_zsreg(uap, R1, uap->curregs[R1]);
1357
1358	/* Setup new port configuration */
1359	__pmz_set_termios(port, termios, old);
1360
1361	/* Re-enable IRQs on the port */
1362	if (ZS_IS_OPEN(uap)) {
1363		uap->curregs[R1] |= INT_ALL_Rx | TxINT_ENAB;
1364		if (!ZS_IS_EXTCLK(uap))
1365			uap->curregs[R1] |= EXT_INT_ENAB;
1366		write_zsreg(uap, R1, uap->curregs[R1]);
1367	}
1368	spin_unlock_irqrestore(&port->lock, flags);
1369}
1370
1371static const char *pmz_type(struct uart_port *port)
1372{
1373	struct uart_pmac_port *uap = to_pmz(port);
1374
1375	if (ZS_IS_IRDA(uap))
1376		return "Z85c30 ESCC - Infrared port";
1377	else if (ZS_IS_INTMODEM(uap))
1378		return "Z85c30 ESCC - Internal modem";
1379	return "Z85c30 ESCC - Serial port";
1380}
1381
1382/* We do not request/release mappings of the registers here, this
1383 * happens at early serial probe time.
1384 */
1385static void pmz_release_port(struct uart_port *port)
1386{
1387}
1388
1389static int pmz_request_port(struct uart_port *port)
1390{
1391	return 0;
1392}
1393
1394/* These do not need to do anything interesting either.  */
1395static void pmz_config_port(struct uart_port *port, int flags)
1396{
1397}
1398
1399/* We do not support letting the user mess with the divisor, IRQ, etc. */
1400static int pmz_verify_port(struct uart_port *port, struct serial_struct *ser)
1401{
1402	return -EINVAL;
1403}
1404
1405#ifdef CONFIG_CONSOLE_POLL
1406
1407static int pmz_poll_get_char(struct uart_port *port)
1408{
1409	struct uart_pmac_port *uap = (struct uart_pmac_port *)port;
 
1410
1411	while ((read_zsreg(uap, R0) & Rx_CH_AV) == 0)
1412		udelay(5);
1413	return read_zsdata(uap);
 
 
 
 
 
1414}
1415
1416static void pmz_poll_put_char(struct uart_port *port, unsigned char c)
1417{
1418	struct uart_pmac_port *uap = (struct uart_pmac_port *)port;
1419
1420	/* Wait for the transmit buffer to empty. */
1421	while ((read_zsreg(uap, R0) & Tx_BUF_EMP) == 0)
1422		udelay(5);
1423	write_zsdata(uap, c);
1424}
1425
1426#endif /* CONFIG_CONSOLE_POLL */
1427
1428static struct uart_ops pmz_pops = {
1429	.tx_empty	=	pmz_tx_empty,
1430	.set_mctrl	=	pmz_set_mctrl,
1431	.get_mctrl	=	pmz_get_mctrl,
1432	.stop_tx	=	pmz_stop_tx,
1433	.start_tx	=	pmz_start_tx,
1434	.stop_rx	=	pmz_stop_rx,
1435	.enable_ms	=	pmz_enable_ms,
1436	.break_ctl	=	pmz_break_ctl,
1437	.startup	=	pmz_startup,
1438	.shutdown	=	pmz_shutdown,
1439	.set_termios	=	pmz_set_termios,
1440	.type		=	pmz_type,
1441	.release_port	=	pmz_release_port,
1442	.request_port	=	pmz_request_port,
1443	.config_port	=	pmz_config_port,
1444	.verify_port	=	pmz_verify_port,
1445#ifdef CONFIG_CONSOLE_POLL
1446	.poll_get_char	=	pmz_poll_get_char,
1447	.poll_put_char	=	pmz_poll_put_char,
1448#endif
1449};
1450
1451#ifdef CONFIG_PPC_PMAC
1452
1453/*
1454 * Setup one port structure after probing, HW is down at this point,
1455 * Unlike sunzilog, we don't need to pre-init the spinlock as we don't
1456 * register our console before uart_add_one_port() is called
1457 */
1458static int __init pmz_init_port(struct uart_pmac_port *uap)
1459{
1460	struct device_node *np = uap->node;
1461	const char *conn;
1462	const struct slot_names_prop {
1463		int	count;
1464		char	name[1];
1465	} *slots;
1466	int len;
1467	struct resource r_ports, r_rxdma, r_txdma;
1468
1469	/*
1470	 * Request & map chip registers
1471	 */
1472	if (of_address_to_resource(np, 0, &r_ports))
1473		return -ENODEV;
1474	uap->port.mapbase = r_ports.start;
1475	uap->port.membase = ioremap(uap->port.mapbase, 0x1000);
1476
1477	uap->control_reg = uap->port.membase;
1478	uap->data_reg = uap->control_reg + 0x10;
1479	
1480	/*
1481	 * Request & map DBDMA registers
1482	 */
1483#ifdef HAS_DBDMA
1484	if (of_address_to_resource(np, 1, &r_txdma) == 0 &&
1485	    of_address_to_resource(np, 2, &r_rxdma) == 0)
1486		uap->flags |= PMACZILOG_FLAG_HAS_DMA;
1487#else
1488	memset(&r_txdma, 0, sizeof(struct resource));
1489	memset(&r_rxdma, 0, sizeof(struct resource));
1490#endif	
1491	if (ZS_HAS_DMA(uap)) {
1492		uap->tx_dma_regs = ioremap(r_txdma.start, 0x100);
1493		if (uap->tx_dma_regs == NULL) {	
1494			uap->flags &= ~PMACZILOG_FLAG_HAS_DMA;
1495			goto no_dma;
1496		}
1497		uap->rx_dma_regs = ioremap(r_rxdma.start, 0x100);
1498		if (uap->rx_dma_regs == NULL) {	
1499			iounmap(uap->tx_dma_regs);
1500			uap->tx_dma_regs = NULL;
1501			uap->flags &= ~PMACZILOG_FLAG_HAS_DMA;
1502			goto no_dma;
1503		}
1504		uap->tx_dma_irq = irq_of_parse_and_map(np, 1);
1505		uap->rx_dma_irq = irq_of_parse_and_map(np, 2);
1506	}
1507no_dma:
1508
1509	/*
1510	 * Detect port type
1511	 */
1512	if (of_device_is_compatible(np, "cobalt"))
1513		uap->flags |= PMACZILOG_FLAG_IS_INTMODEM;
1514	conn = of_get_property(np, "AAPL,connector", &len);
1515	if (conn && (strcmp(conn, "infrared") == 0))
1516		uap->flags |= PMACZILOG_FLAG_IS_IRDA;
1517	uap->port_type = PMAC_SCC_ASYNC;
1518	/* 1999 Powerbook G3 has slot-names property instead */
1519	slots = of_get_property(np, "slot-names", &len);
1520	if (slots && slots->count > 0) {
1521		if (strcmp(slots->name, "IrDA") == 0)
1522			uap->flags |= PMACZILOG_FLAG_IS_IRDA;
1523		else if (strcmp(slots->name, "Modem") == 0)
1524			uap->flags |= PMACZILOG_FLAG_IS_INTMODEM;
1525	}
1526	if (ZS_IS_IRDA(uap))
1527		uap->port_type = PMAC_SCC_IRDA;
1528	if (ZS_IS_INTMODEM(uap)) {
1529		struct device_node* i2c_modem =
1530			of_find_node_by_name(NULL, "i2c-modem");
1531		if (i2c_modem) {
1532			const char* mid =
1533				of_get_property(i2c_modem, "modem-id", NULL);
1534			if (mid) switch(*mid) {
1535			case 0x04 :
1536			case 0x05 :
1537			case 0x07 :
1538			case 0x08 :
1539			case 0x0b :
1540			case 0x0c :
1541				uap->port_type = PMAC_SCC_I2S1;
1542			}
1543			printk(KERN_INFO "pmac_zilog: i2c-modem detected, id: %d\n",
1544				mid ? (*mid) : 0);
1545			of_node_put(i2c_modem);
1546		} else {
1547			printk(KERN_INFO "pmac_zilog: serial modem detected\n");
1548		}
1549	}
1550
1551	/*
1552	 * Init remaining bits of "port" structure
1553	 */
1554	uap->port.iotype = UPIO_MEM;
1555	uap->port.irq = irq_of_parse_and_map(np, 0);
1556	uap->port.uartclk = ZS_CLOCK;
1557	uap->port.fifosize = 1;
1558	uap->port.ops = &pmz_pops;
1559	uap->port.type = PORT_PMAC_ZILOG;
1560	uap->port.flags = 0;
1561
1562	/*
1563	 * Fixup for the port on Gatwick for which the device-tree has
1564	 * missing interrupts. Normally, the macio_dev would contain
1565	 * fixed up interrupt info, but we use the device-tree directly
1566	 * here due to early probing so we need the fixup too.
1567	 */
1568	if (uap->port.irq == NO_IRQ &&
1569	    np->parent && np->parent->parent &&
1570	    of_device_is_compatible(np->parent->parent, "gatwick")) {
1571		/* IRQs on gatwick are offset by 64 */
1572		uap->port.irq = irq_create_mapping(NULL, 64 + 15);
1573		uap->tx_dma_irq = irq_create_mapping(NULL, 64 + 4);
1574		uap->rx_dma_irq = irq_create_mapping(NULL, 64 + 5);
1575	}
1576
1577	/* Setup some valid baud rate information in the register
1578	 * shadows so we don't write crap there before baud rate is
1579	 * first initialized.
1580	 */
1581	pmz_convert_to_zs(uap, CS8, 0, 9600);
1582
1583	return 0;
1584}
1585
1586/*
1587 * Get rid of a port on module removal
1588 */
1589static void pmz_dispose_port(struct uart_pmac_port *uap)
1590{
1591	struct device_node *np;
1592
1593	np = uap->node;
1594	iounmap(uap->rx_dma_regs);
1595	iounmap(uap->tx_dma_regs);
1596	iounmap(uap->control_reg);
1597	uap->node = NULL;
1598	of_node_put(np);
1599	memset(uap, 0, sizeof(struct uart_pmac_port));
1600}
1601
1602/*
1603 * Called upon match with an escc node in the device-tree.
1604 */
1605static int pmz_attach(struct macio_dev *mdev, const struct of_device_id *match)
1606{
 
1607	int i;
1608	
1609	/* Iterate the pmz_ports array to find a matching entry
1610	 */
1611	for (i = 0; i < MAX_ZS_PORTS; i++)
1612		if (pmz_ports[i].node == mdev->ofdev.dev.of_node) {
1613			struct uart_pmac_port *uap = &pmz_ports[i];
 
 
1614
1615			uap->dev = mdev;
1616			dev_set_drvdata(&mdev->ofdev.dev, uap);
1617			if (macio_request_resources(uap->dev, "pmac_zilog"))
1618				printk(KERN_WARNING "%s: Failed to request resource"
1619				       ", port still active\n",
1620				       uap->node->name);
1621			else
1622				uap->flags |= PMACZILOG_FLAG_RSRC_REQUESTED;				
1623			return 0;
1624		}
1625	return -ENODEV;
 
 
 
 
 
 
1626}
1627
1628/*
1629 * That one should not be called, macio isn't really a hotswap device,
1630 * we don't expect one of those serial ports to go away...
1631 */
1632static int pmz_detach(struct macio_dev *mdev)
1633{
1634	struct uart_pmac_port	*uap = dev_get_drvdata(&mdev->ofdev.dev);
1635	
1636	if (!uap)
1637		return -ENODEV;
1638
 
 
1639	if (uap->flags & PMACZILOG_FLAG_RSRC_REQUESTED) {
1640		macio_release_resources(uap->dev);
1641		uap->flags &= ~PMACZILOG_FLAG_RSRC_REQUESTED;
1642	}
1643	dev_set_drvdata(&mdev->ofdev.dev, NULL);
1644	uap->dev = NULL;
 
1645	
1646	return 0;
1647}
1648
1649
1650static int pmz_suspend(struct macio_dev *mdev, pm_message_t pm_state)
1651{
1652	struct uart_pmac_port *uap = dev_get_drvdata(&mdev->ofdev.dev);
1653	struct uart_state *state;
1654	unsigned long flags;
1655
1656	if (uap == NULL) {
1657		printk("HRM... pmz_suspend with NULL uap\n");
1658		return 0;
1659	}
1660
1661	if (pm_state.event == mdev->ofdev.dev.power.power_state.event)
1662		return 0;
1663
1664	pmz_debug("suspend, switching to state %d\n", pm_state.event);
1665
1666	state = pmz_uart_reg.state + uap->port.line;
1667
1668	mutex_lock(&pmz_irq_mutex);
1669	mutex_lock(&state->port.mutex);
1670
1671	spin_lock_irqsave(&uap->port.lock, flags);
1672
1673	if (ZS_IS_OPEN(uap) || ZS_IS_CONS(uap)) {
1674		/* Disable receiver and transmitter.  */
1675		uap->curregs[R3] &= ~RxENABLE;
1676		uap->curregs[R5] &= ~TxENABLE;
1677
1678		/* Disable all interrupts and BRK assertion.  */
1679		uap->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
1680		uap->curregs[R5] &= ~SND_BRK;
1681		pmz_load_zsregs(uap, uap->curregs);
1682		uap->flags |= PMACZILOG_FLAG_IS_ASLEEP;
1683		mb();
1684	}
1685
1686	spin_unlock_irqrestore(&uap->port.lock, flags);
1687
1688	if (ZS_IS_OPEN(uap) || ZS_IS_OPEN(uap->mate))
1689		if (ZS_IS_ASLEEP(uap->mate) && ZS_IS_IRQ_ON(pmz_get_port_A(uap))) {
1690			pmz_get_port_A(uap)->flags &= ~PMACZILOG_FLAG_IS_IRQ_ON;
1691			disable_irq(uap->port.irq);
1692		}
1693
1694	if (ZS_IS_CONS(uap))
1695		uap->port.cons->flags &= ~CON_ENABLED;
1696
1697	/* Shut the chip down */
1698	pmz_set_scc_power(uap, 0);
1699
1700	mutex_unlock(&state->port.mutex);
1701	mutex_unlock(&pmz_irq_mutex);
1702
1703	pmz_debug("suspend, switching complete\n");
1704
1705	mdev->ofdev.dev.power.power_state = pm_state;
1706
1707	return 0;
1708}
1709
1710
1711static int pmz_resume(struct macio_dev *mdev)
1712{
1713	struct uart_pmac_port *uap = dev_get_drvdata(&mdev->ofdev.dev);
1714	struct uart_state *state;
1715	unsigned long flags;
1716	int pwr_delay = 0;
1717
1718	if (uap == NULL)
1719		return 0;
1720
1721	if (mdev->ofdev.dev.power.power_state.event == PM_EVENT_ON)
1722		return 0;
1723	
1724	pmz_debug("resume, switching to state 0\n");
1725
1726	state = pmz_uart_reg.state + uap->port.line;
1727
1728	mutex_lock(&pmz_irq_mutex);
1729	mutex_lock(&state->port.mutex);
1730
1731	spin_lock_irqsave(&uap->port.lock, flags);
1732	if (!ZS_IS_OPEN(uap) && !ZS_IS_CONS(uap)) {
1733		spin_unlock_irqrestore(&uap->port.lock, flags);
1734		goto bail;
1735	}
1736	pwr_delay = __pmz_startup(uap);
1737
1738	/* Take care of config that may have changed while asleep */
1739	__pmz_set_termios(&uap->port, &uap->termios_cache, NULL);
1740
1741	if (ZS_IS_OPEN(uap)) {
1742		/* Enable interrupts */		
1743		uap->curregs[R1] |= INT_ALL_Rx | TxINT_ENAB;
1744		if (!ZS_IS_EXTCLK(uap))
1745			uap->curregs[R1] |= EXT_INT_ENAB;
1746		write_zsreg(uap, R1, uap->curregs[R1]);
1747	}
1748
1749	spin_unlock_irqrestore(&uap->port.lock, flags);
1750
1751	if (ZS_IS_CONS(uap))
1752		uap->port.cons->flags |= CON_ENABLED;
1753
1754	/* Re-enable IRQ on the controller */
1755	if (ZS_IS_OPEN(uap) && !ZS_IS_IRQ_ON(pmz_get_port_A(uap))) {
1756		pmz_get_port_A(uap)->flags |= PMACZILOG_FLAG_IS_IRQ_ON;
1757		enable_irq(uap->port.irq);
1758	}
1759
1760 bail:
1761	mutex_unlock(&state->port.mutex);
1762	mutex_unlock(&pmz_irq_mutex);
1763
1764	/* Right now, we deal with delay by blocking here, I'll be
1765	 * smarter later on
1766	 */
1767	if (pwr_delay != 0) {
1768		pmz_debug("pmz: delaying %d ms\n", pwr_delay);
1769		msleep(pwr_delay);
1770	}
1771
1772	pmz_debug("resume, switching complete\n");
1773
1774	mdev->ofdev.dev.power.power_state.event = PM_EVENT_ON;
1775
1776	return 0;
1777}
1778
1779/*
1780 * Probe all ports in the system and build the ports array, we register
1781 * with the serial layer at this point, the macio-type probing is only
1782 * used later to "attach" to the sysfs tree so we get power management
1783 * events
1784 */
1785static int __init pmz_probe(void)
1786{
1787	struct device_node	*node_p, *node_a, *node_b, *np;
1788	int			count = 0;
1789	int			rc;
1790
1791	/*
1792	 * Find all escc chips in the system
1793	 */
1794	node_p = of_find_node_by_name(NULL, "escc");
1795	while (node_p) {
1796		/*
1797		 * First get channel A/B node pointers
1798		 * 
1799		 * TODO: Add routines with proper locking to do that...
1800		 */
1801		node_a = node_b = NULL;
1802		for (np = NULL; (np = of_get_next_child(node_p, np)) != NULL;) {
1803			if (strncmp(np->name, "ch-a", 4) == 0)
1804				node_a = of_node_get(np);
1805			else if (strncmp(np->name, "ch-b", 4) == 0)
1806				node_b = of_node_get(np);
1807		}
1808		if (!node_a && !node_b) {
1809			of_node_put(node_a);
1810			of_node_put(node_b);
1811			printk(KERN_ERR "pmac_zilog: missing node %c for escc %s\n",
1812				(!node_a) ? 'a' : 'b', node_p->full_name);
1813			goto next;
1814		}
1815
1816		/*
1817		 * Fill basic fields in the port structures
1818		 */
1819		pmz_ports[count].mate		= &pmz_ports[count+1];
1820		pmz_ports[count+1].mate		= &pmz_ports[count];
 
 
1821		pmz_ports[count].flags		= PMACZILOG_FLAG_IS_CHANNEL_A;
1822		pmz_ports[count].node		= node_a;
1823		pmz_ports[count+1].node		= node_b;
1824		pmz_ports[count].port.line	= count;
1825		pmz_ports[count+1].port.line	= count+1;
1826
1827		/*
1828		 * Setup the ports for real
1829		 */
1830		rc = pmz_init_port(&pmz_ports[count]);
1831		if (rc == 0 && node_b != NULL)
1832			rc = pmz_init_port(&pmz_ports[count+1]);
1833		if (rc != 0) {
1834			of_node_put(node_a);
1835			of_node_put(node_b);
1836			memset(&pmz_ports[count], 0, sizeof(struct uart_pmac_port));
1837			memset(&pmz_ports[count+1], 0, sizeof(struct uart_pmac_port));
1838			goto next;
1839		}
1840		count += 2;
1841next:
1842		node_p = of_find_node_by_name(node_p, "escc");
1843	}
1844	pmz_ports_count = count;
1845
1846	return 0;
1847}
1848
1849#else
1850
1851extern struct platform_device scc_a_pdev, scc_b_pdev;
1852
1853static int __init pmz_init_port(struct uart_pmac_port *uap)
1854{
1855	struct resource *r_ports;
1856	int irq;
1857
1858	r_ports = platform_get_resource(uap->node, IORESOURCE_MEM, 0);
1859	irq = platform_get_irq(uap->node, 0);
1860	if (!r_ports || !irq)
1861		return -ENODEV;
1862
1863	uap->port.mapbase  = r_ports->start;
1864	uap->port.membase  = (unsigned char __iomem *) r_ports->start;
1865	uap->port.iotype   = UPIO_MEM;
1866	uap->port.irq      = irq;
1867	uap->port.uartclk  = ZS_CLOCK;
1868	uap->port.fifosize = 1;
1869	uap->port.ops      = &pmz_pops;
1870	uap->port.type     = PORT_PMAC_ZILOG;
1871	uap->port.flags    = 0;
1872
1873	uap->control_reg   = uap->port.membase;
1874	uap->data_reg      = uap->control_reg + 4;
1875	uap->port_type     = 0;
1876
1877	pmz_convert_to_zs(uap, CS8, 0, 9600);
1878
1879	return 0;
1880}
1881
1882static int __init pmz_probe(void)
1883{
1884	int err;
1885
1886	pmz_ports_count = 0;
1887
1888	pmz_ports[0].mate      = &pmz_ports[1];
1889	pmz_ports[0].port.line = 0;
1890	pmz_ports[0].flags     = PMACZILOG_FLAG_IS_CHANNEL_A;
1891	pmz_ports[0].node      = &scc_a_pdev;
1892	err = pmz_init_port(&pmz_ports[0]);
1893	if (err)
1894		return err;
1895	pmz_ports_count++;
1896
 
1897	pmz_ports[1].mate      = &pmz_ports[0];
1898	pmz_ports[1].port.line = 1;
1899	pmz_ports[1].flags     = 0;
1900	pmz_ports[1].node      = &scc_b_pdev;
1901	err = pmz_init_port(&pmz_ports[1]);
1902	if (err)
1903		return err;
1904	pmz_ports_count++;
1905
1906	return 0;
1907}
1908
1909static void pmz_dispose_port(struct uart_pmac_port *uap)
1910{
1911	memset(uap, 0, sizeof(struct uart_pmac_port));
1912}
1913
1914static int __init pmz_attach(struct platform_device *pdev)
1915{
 
1916	int i;
1917
 
1918	for (i = 0; i < pmz_ports_count; i++)
1919		if (pmz_ports[i].node == pdev)
1920			return 0;
1921	return -ENODEV;
 
 
 
 
 
 
 
1922}
1923
1924static int __exit pmz_detach(struct platform_device *pdev)
1925{
 
 
 
 
 
 
 
 
 
 
1926	return 0;
1927}
1928
1929#endif /* !CONFIG_PPC_PMAC */
1930
1931#ifdef CONFIG_SERIAL_PMACZILOG_CONSOLE
1932
1933static void pmz_console_write(struct console *con, const char *s, unsigned int count);
1934static int __init pmz_console_setup(struct console *co, char *options);
1935
1936static struct console pmz_console = {
1937	.name	=	PMACZILOG_NAME,
1938	.write	=	pmz_console_write,
1939	.device	=	uart_console_device,
1940	.setup	=	pmz_console_setup,
1941	.flags	=	CON_PRINTBUFFER,
1942	.index	=	-1,
1943	.data   =	&pmz_uart_reg,
1944};
1945
1946#define PMACZILOG_CONSOLE	&pmz_console
1947#else /* CONFIG_SERIAL_PMACZILOG_CONSOLE */
1948#define PMACZILOG_CONSOLE	(NULL)
1949#endif /* CONFIG_SERIAL_PMACZILOG_CONSOLE */
1950
1951/*
1952 * Register the driver, console driver and ports with the serial
1953 * core
1954 */
1955static int __init pmz_register(void)
1956{
1957	int i, rc;
1958	
1959	pmz_uart_reg.nr = pmz_ports_count;
1960	pmz_uart_reg.cons = PMACZILOG_CONSOLE;
1961
1962	/*
1963	 * Register this driver with the serial core
1964	 */
1965	rc = uart_register_driver(&pmz_uart_reg);
1966	if (rc)
1967		return rc;
1968
1969	/*
1970	 * Register each port with the serial core
1971	 */
1972	for (i = 0; i < pmz_ports_count; i++) {
1973		struct uart_pmac_port *uport = &pmz_ports[i];
1974		/* NULL node may happen on wallstreet */
1975		if (uport->node != NULL)
1976			rc = uart_add_one_port(&pmz_uart_reg, &uport->port);
1977		if (rc)
1978			goto err_out;
1979	}
1980
1981	return 0;
1982err_out:
1983	while (i-- > 0) {
1984		struct uart_pmac_port *uport = &pmz_ports[i];
1985		uart_remove_one_port(&pmz_uart_reg, &uport->port);
1986	}
1987	uart_unregister_driver(&pmz_uart_reg);
1988	return rc;
1989}
1990
1991#ifdef CONFIG_PPC_PMAC
1992
1993static struct of_device_id pmz_match[] = 
1994{
1995	{
1996	.name		= "ch-a",
1997	},
1998	{
1999	.name		= "ch-b",
2000	},
2001	{},
2002};
2003MODULE_DEVICE_TABLE (of, pmz_match);
2004
2005static struct macio_driver pmz_driver = {
2006	.driver = {
2007		.name 		= "pmac_zilog",
2008		.owner		= THIS_MODULE,
2009		.of_match_table	= pmz_match,
2010	},
2011	.probe		= pmz_attach,
2012	.remove		= pmz_detach,
2013	.suspend	= pmz_suspend,
2014	.resume		= pmz_resume,
2015};
2016
2017#else
2018
2019static struct platform_driver pmz_driver = {
2020	.remove		= __exit_p(pmz_detach),
2021	.driver		= {
2022		.name		= "scc",
2023		.owner		= THIS_MODULE,
2024	},
2025};
2026
2027#endif /* !CONFIG_PPC_PMAC */
2028
2029static int __init init_pmz(void)
2030{
2031	int rc, i;
2032	printk(KERN_INFO "%s\n", version);
2033
2034	/* 
2035	 * First, we need to do a direct OF-based probe pass. We
2036	 * do that because we want serial console up before the
2037	 * macio stuffs calls us back, and since that makes it
2038	 * easier to pass the proper number of channels to
2039	 * uart_register_driver()
2040	 */
2041	if (pmz_ports_count == 0)
2042		pmz_probe();
2043
2044	/*
2045	 * Bail early if no port found
2046	 */
2047	if (pmz_ports_count == 0)
2048		return -ENODEV;
2049
2050	/*
2051	 * Now we register with the serial layer
2052	 */
2053	rc = pmz_register();
2054	if (rc) {
2055		printk(KERN_ERR 
2056			"pmac_zilog: Error registering serial device, disabling pmac_zilog.\n"
2057		 	"pmac_zilog: Did another serial driver already claim the minors?\n"); 
2058		/* effectively "pmz_unprobe()" */
2059		for (i=0; i < pmz_ports_count; i++)
2060			pmz_dispose_port(&pmz_ports[i]);
2061		return rc;
2062	}
2063
2064	/*
2065	 * Then we register the macio driver itself
2066	 */
2067#ifdef CONFIG_PPC_PMAC
2068	return macio_register_driver(&pmz_driver);
2069#else
2070	return platform_driver_probe(&pmz_driver, pmz_attach);
2071#endif
2072}
2073
2074static void __exit exit_pmz(void)
2075{
2076	int i;
2077
2078#ifdef CONFIG_PPC_PMAC
2079	/* Get rid of macio-driver (detach from macio) */
2080	macio_unregister_driver(&pmz_driver);
2081#else
2082	platform_driver_unregister(&pmz_driver);
2083#endif
2084
2085	for (i = 0; i < pmz_ports_count; i++) {
2086		struct uart_pmac_port *uport = &pmz_ports[i];
2087		if (uport->node != NULL) {
2088			uart_remove_one_port(&pmz_uart_reg, &uport->port);
2089			pmz_dispose_port(uport);
2090		}
 
 
 
2091	}
2092	/* Unregister UART driver */
2093	uart_unregister_driver(&pmz_uart_reg);
2094}
2095
2096#ifdef CONFIG_SERIAL_PMACZILOG_CONSOLE
2097
2098static void pmz_console_putchar(struct uart_port *port, int ch)
2099{
2100	struct uart_pmac_port *uap = (struct uart_pmac_port *)port;
2101
2102	/* Wait for the transmit buffer to empty. */
2103	while ((read_zsreg(uap, R0) & Tx_BUF_EMP) == 0)
2104		udelay(5);
2105	write_zsdata(uap, ch);
2106}
2107
2108/*
2109 * Print a string to the serial port trying not to disturb
2110 * any possible real use of the port...
2111 */
2112static void pmz_console_write(struct console *con, const char *s, unsigned int count)
2113{
2114	struct uart_pmac_port *uap = &pmz_ports[con->index];
2115	unsigned long flags;
2116
2117	if (ZS_IS_ASLEEP(uap))
2118		return;
2119	spin_lock_irqsave(&uap->port.lock, flags);
2120
2121	/* Turn of interrupts and enable the transmitter. */
2122	write_zsreg(uap, R1, uap->curregs[1] & ~TxINT_ENAB);
2123	write_zsreg(uap, R5, uap->curregs[5] | TxENABLE | RTS | DTR);
2124
2125	uart_console_write(&uap->port, s, count, pmz_console_putchar);
2126
2127	/* Restore the values in the registers. */
2128	write_zsreg(uap, R1, uap->curregs[1]);
2129	/* Don't disable the transmitter. */
2130
2131	spin_unlock_irqrestore(&uap->port.lock, flags);
2132}
2133
2134/*
2135 * Setup the serial console
2136 */
2137static int __init pmz_console_setup(struct console *co, char *options)
2138{
2139	struct uart_pmac_port *uap;
2140	struct uart_port *port;
2141	int baud = 38400;
2142	int bits = 8;
2143	int parity = 'n';
2144	int flow = 'n';
2145	unsigned long pwr_delay;
2146
2147	/*
2148	 * XServe's default to 57600 bps
2149	 */
2150	if (of_machine_is_compatible("RackMac1,1")
2151	    || of_machine_is_compatible("RackMac1,2")
2152	    || of_machine_is_compatible("MacRISC4"))
2153		baud = 57600;
2154
2155	/*
2156	 * Check whether an invalid uart number has been specified, and
2157	 * if so, search for the first available port that does have
2158	 * console support.
2159	 */
2160	if (co->index >= pmz_ports_count)
2161		co->index = 0;
2162	uap = &pmz_ports[co->index];
 
2163	if (uap->node == NULL)
2164		return -ENODEV;
 
 
 
 
2165	port = &uap->port;
2166
2167	/*
2168	 * Mark port as beeing a console
2169	 */
2170	uap->flags |= PMACZILOG_FLAG_IS_CONS;
2171
2172	/*
2173	 * Temporary fix for uart layer who didn't setup the spinlock yet
2174	 */
2175	spin_lock_init(&port->lock);
2176
2177	/*
2178	 * Enable the hardware
2179	 */
2180	pwr_delay = __pmz_startup(uap);
2181	if (pwr_delay)
2182		mdelay(pwr_delay);
2183	
2184	if (options)
2185		uart_parse_options(options, &baud, &parity, &bits, &flow);
2186
2187	return uart_set_options(port, co, baud, parity, bits, flow);
2188}
2189
2190static int __init pmz_console_init(void)
2191{
2192	/* Probe ports */
2193	pmz_probe();
2194
2195	/* TODO: Autoprobe console based on OF */
2196	/* pmz_console.index = i; */
2197	register_console(&pmz_console);
2198
2199	return 0;
2200
2201}
2202console_initcall(pmz_console_init);
2203#endif /* CONFIG_SERIAL_PMACZILOG_CONSOLE */
2204
2205module_init(init_pmz);
2206module_exit(exit_pmz);