Loading...
1/*
2 * max6875.c - driver for MAX6874/MAX6875
3 *
4 * Copyright (C) 2005 Ben Gardner <bgardner@wabtec.com>
5 *
6 * Based on eeprom.c
7 *
8 * The MAX6875 has a bank of registers and two banks of EEPROM.
9 * Address ranges are defined as follows:
10 * * 0x0000 - 0x0046 = configuration registers
11 * * 0x8000 - 0x8046 = configuration EEPROM
12 * * 0x8100 - 0x82FF = user EEPROM
13 *
14 * This driver makes the user EEPROM available for read.
15 *
16 * The registers & config EEPROM should be accessed via i2c-dev.
17 *
18 * The MAX6875 ignores the lowest address bit, so each chip responds to
19 * two addresses - 0x50/0x51 and 0x52/0x53.
20 *
21 * Note that the MAX6875 uses i2c_smbus_write_byte_data() to set the read
22 * address, so this driver is destructive if loaded for the wrong EEPROM chip.
23 *
24 * This program is free software; you can redistribute it and/or modify
25 * it under the terms of the GNU General Public License as published by
26 * the Free Software Foundation; version 2 of the License.
27 */
28
29#include <linux/kernel.h>
30#include <linux/init.h>
31#include <linux/module.h>
32#include <linux/slab.h>
33#include <linux/i2c.h>
34#include <linux/mutex.h>
35
36/* The MAX6875 can only read/write 16 bytes at a time */
37#define SLICE_SIZE 16
38#define SLICE_BITS 4
39
40/* USER EEPROM is at addresses 0x8100 - 0x82FF */
41#define USER_EEPROM_BASE 0x8100
42#define USER_EEPROM_SIZE 0x0200
43#define USER_EEPROM_SLICES 32
44
45/* MAX6875 commands */
46#define MAX6875_CMD_BLK_READ 0x84
47
48/* Each client has this additional data */
49struct max6875_data {
50 struct i2c_client *fake_client;
51 struct mutex update_lock;
52
53 u32 valid;
54 u8 data[USER_EEPROM_SIZE];
55 unsigned long last_updated[USER_EEPROM_SLICES];
56};
57
58static void max6875_update_slice(struct i2c_client *client, int slice)
59{
60 struct max6875_data *data = i2c_get_clientdata(client);
61 int i, j, addr;
62 u8 *buf;
63
64 if (slice >= USER_EEPROM_SLICES)
65 return;
66
67 mutex_lock(&data->update_lock);
68
69 buf = &data->data[slice << SLICE_BITS];
70
71 if (!(data->valid & (1 << slice)) ||
72 time_after(jiffies, data->last_updated[slice])) {
73
74 dev_dbg(&client->dev, "Starting update of slice %u\n", slice);
75
76 data->valid &= ~(1 << slice);
77
78 addr = USER_EEPROM_BASE + (slice << SLICE_BITS);
79
80 /* select the eeprom address */
81 if (i2c_smbus_write_byte_data(client, addr >> 8, addr & 0xFF)) {
82 dev_err(&client->dev, "address set failed\n");
83 goto exit_up;
84 }
85
86 if (i2c_check_functionality(client->adapter,
87 I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
88 if (i2c_smbus_read_i2c_block_data(client,
89 MAX6875_CMD_BLK_READ,
90 SLICE_SIZE,
91 buf) != SLICE_SIZE) {
92 goto exit_up;
93 }
94 } else {
95 for (i = 0; i < SLICE_SIZE; i++) {
96 j = i2c_smbus_read_byte(client);
97 if (j < 0) {
98 goto exit_up;
99 }
100 buf[i] = j;
101 }
102 }
103 data->last_updated[slice] = jiffies;
104 data->valid |= (1 << slice);
105 }
106exit_up:
107 mutex_unlock(&data->update_lock);
108}
109
110static ssize_t max6875_read(struct file *filp, struct kobject *kobj,
111 struct bin_attribute *bin_attr,
112 char *buf, loff_t off, size_t count)
113{
114 struct i2c_client *client = kobj_to_i2c_client(kobj);
115 struct max6875_data *data = i2c_get_clientdata(client);
116 int slice, max_slice;
117
118 if (off > USER_EEPROM_SIZE)
119 return 0;
120
121 if (off + count > USER_EEPROM_SIZE)
122 count = USER_EEPROM_SIZE - off;
123
124 /* refresh slices which contain requested bytes */
125 max_slice = (off + count - 1) >> SLICE_BITS;
126 for (slice = (off >> SLICE_BITS); slice <= max_slice; slice++)
127 max6875_update_slice(client, slice);
128
129 memcpy(buf, &data->data[off], count);
130
131 return count;
132}
133
134static struct bin_attribute user_eeprom_attr = {
135 .attr = {
136 .name = "eeprom",
137 .mode = S_IRUGO,
138 },
139 .size = USER_EEPROM_SIZE,
140 .read = max6875_read,
141};
142
143static int max6875_probe(struct i2c_client *client,
144 const struct i2c_device_id *id)
145{
146 struct i2c_adapter *adapter = client->adapter;
147 struct max6875_data *data;
148 int err;
149
150 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WRITE_BYTE_DATA
151 | I2C_FUNC_SMBUS_READ_BYTE))
152 return -ENODEV;
153
154 /* Only bind to even addresses */
155 if (client->addr & 1)
156 return -ENODEV;
157
158 if (!(data = kzalloc(sizeof(struct max6875_data), GFP_KERNEL)))
159 return -ENOMEM;
160
161 /* A fake client is created on the odd address */
162 data->fake_client = i2c_new_dummy(client->adapter, client->addr + 1);
163 if (!data->fake_client) {
164 err = -ENOMEM;
165 goto exit_kfree;
166 }
167
168 /* Init real i2c_client */
169 i2c_set_clientdata(client, data);
170 mutex_init(&data->update_lock);
171
172 err = sysfs_create_bin_file(&client->dev.kobj, &user_eeprom_attr);
173 if (err)
174 goto exit_remove_fake;
175
176 return 0;
177
178exit_remove_fake:
179 i2c_unregister_device(data->fake_client);
180exit_kfree:
181 kfree(data);
182 return err;
183}
184
185static int max6875_remove(struct i2c_client *client)
186{
187 struct max6875_data *data = i2c_get_clientdata(client);
188
189 i2c_unregister_device(data->fake_client);
190
191 sysfs_remove_bin_file(&client->dev.kobj, &user_eeprom_attr);
192 kfree(data);
193
194 return 0;
195}
196
197static const struct i2c_device_id max6875_id[] = {
198 { "max6875", 0 },
199 { }
200};
201
202static struct i2c_driver max6875_driver = {
203 .driver = {
204 .name = "max6875",
205 },
206 .probe = max6875_probe,
207 .remove = max6875_remove,
208 .id_table = max6875_id,
209};
210
211static int __init max6875_init(void)
212{
213 return i2c_add_driver(&max6875_driver);
214}
215
216static void __exit max6875_exit(void)
217{
218 i2c_del_driver(&max6875_driver);
219}
220
221
222MODULE_AUTHOR("Ben Gardner <bgardner@wabtec.com>");
223MODULE_DESCRIPTION("MAX6875 driver");
224MODULE_LICENSE("GPL");
225
226module_init(max6875_init);
227module_exit(max6875_exit);
1/*
2 * max6875.c - driver for MAX6874/MAX6875
3 *
4 * Copyright (C) 2005 Ben Gardner <bgardner@wabtec.com>
5 *
6 * Based on eeprom.c
7 *
8 * The MAX6875 has a bank of registers and two banks of EEPROM.
9 * Address ranges are defined as follows:
10 * * 0x0000 - 0x0046 = configuration registers
11 * * 0x8000 - 0x8046 = configuration EEPROM
12 * * 0x8100 - 0x82FF = user EEPROM
13 *
14 * This driver makes the user EEPROM available for read.
15 *
16 * The registers & config EEPROM should be accessed via i2c-dev.
17 *
18 * The MAX6875 ignores the lowest address bit, so each chip responds to
19 * two addresses - 0x50/0x51 and 0x52/0x53.
20 *
21 * Note that the MAX6875 uses i2c_smbus_write_byte_data() to set the read
22 * address, so this driver is destructive if loaded for the wrong EEPROM chip.
23 *
24 * This program is free software; you can redistribute it and/or modify
25 * it under the terms of the GNU General Public License as published by
26 * the Free Software Foundation; version 2 of the License.
27 */
28
29#include <linux/kernel.h>
30#include <linux/module.h>
31#include <linux/slab.h>
32#include <linux/i2c.h>
33#include <linux/mutex.h>
34
35/* The MAX6875 can only read/write 16 bytes at a time */
36#define SLICE_SIZE 16
37#define SLICE_BITS 4
38
39/* USER EEPROM is at addresses 0x8100 - 0x82FF */
40#define USER_EEPROM_BASE 0x8100
41#define USER_EEPROM_SIZE 0x0200
42#define USER_EEPROM_SLICES 32
43
44/* MAX6875 commands */
45#define MAX6875_CMD_BLK_READ 0x84
46
47/* Each client has this additional data */
48struct max6875_data {
49 struct i2c_client *fake_client;
50 struct mutex update_lock;
51
52 u32 valid;
53 u8 data[USER_EEPROM_SIZE];
54 unsigned long last_updated[USER_EEPROM_SLICES];
55};
56
57static void max6875_update_slice(struct i2c_client *client, int slice)
58{
59 struct max6875_data *data = i2c_get_clientdata(client);
60 int i, j, addr;
61 u8 *buf;
62
63 if (slice >= USER_EEPROM_SLICES)
64 return;
65
66 mutex_lock(&data->update_lock);
67
68 buf = &data->data[slice << SLICE_BITS];
69
70 if (!(data->valid & (1 << slice)) ||
71 time_after(jiffies, data->last_updated[slice])) {
72
73 dev_dbg(&client->dev, "Starting update of slice %u\n", slice);
74
75 data->valid &= ~(1 << slice);
76
77 addr = USER_EEPROM_BASE + (slice << SLICE_BITS);
78
79 /* select the eeprom address */
80 if (i2c_smbus_write_byte_data(client, addr >> 8, addr & 0xFF)) {
81 dev_err(&client->dev, "address set failed\n");
82 goto exit_up;
83 }
84
85 if (i2c_check_functionality(client->adapter,
86 I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
87 if (i2c_smbus_read_i2c_block_data(client,
88 MAX6875_CMD_BLK_READ,
89 SLICE_SIZE,
90 buf) != SLICE_SIZE) {
91 goto exit_up;
92 }
93 } else {
94 for (i = 0; i < SLICE_SIZE; i++) {
95 j = i2c_smbus_read_byte(client);
96 if (j < 0) {
97 goto exit_up;
98 }
99 buf[i] = j;
100 }
101 }
102 data->last_updated[slice] = jiffies;
103 data->valid |= (1 << slice);
104 }
105exit_up:
106 mutex_unlock(&data->update_lock);
107}
108
109static ssize_t max6875_read(struct file *filp, struct kobject *kobj,
110 struct bin_attribute *bin_attr,
111 char *buf, loff_t off, size_t count)
112{
113 struct i2c_client *client = kobj_to_i2c_client(kobj);
114 struct max6875_data *data = i2c_get_clientdata(client);
115 int slice, max_slice;
116
117 if (off > USER_EEPROM_SIZE)
118 return 0;
119
120 if (off + count > USER_EEPROM_SIZE)
121 count = USER_EEPROM_SIZE - off;
122
123 /* refresh slices which contain requested bytes */
124 max_slice = (off + count - 1) >> SLICE_BITS;
125 for (slice = (off >> SLICE_BITS); slice <= max_slice; slice++)
126 max6875_update_slice(client, slice);
127
128 memcpy(buf, &data->data[off], count);
129
130 return count;
131}
132
133static struct bin_attribute user_eeprom_attr = {
134 .attr = {
135 .name = "eeprom",
136 .mode = S_IRUGO,
137 },
138 .size = USER_EEPROM_SIZE,
139 .read = max6875_read,
140};
141
142static int max6875_probe(struct i2c_client *client,
143 const struct i2c_device_id *id)
144{
145 struct i2c_adapter *adapter = client->adapter;
146 struct max6875_data *data;
147 int err;
148
149 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WRITE_BYTE_DATA
150 | I2C_FUNC_SMBUS_READ_BYTE))
151 return -ENODEV;
152
153 /* Only bind to even addresses */
154 if (client->addr & 1)
155 return -ENODEV;
156
157 if (!(data = kzalloc(sizeof(struct max6875_data), GFP_KERNEL)))
158 return -ENOMEM;
159
160 /* A fake client is created on the odd address */
161 data->fake_client = i2c_new_dummy(client->adapter, client->addr + 1);
162 if (!data->fake_client) {
163 err = -ENOMEM;
164 goto exit_kfree;
165 }
166
167 /* Init real i2c_client */
168 i2c_set_clientdata(client, data);
169 mutex_init(&data->update_lock);
170
171 err = sysfs_create_bin_file(&client->dev.kobj, &user_eeprom_attr);
172 if (err)
173 goto exit_remove_fake;
174
175 return 0;
176
177exit_remove_fake:
178 i2c_unregister_device(data->fake_client);
179exit_kfree:
180 kfree(data);
181 return err;
182}
183
184static int max6875_remove(struct i2c_client *client)
185{
186 struct max6875_data *data = i2c_get_clientdata(client);
187
188 i2c_unregister_device(data->fake_client);
189
190 sysfs_remove_bin_file(&client->dev.kobj, &user_eeprom_attr);
191 kfree(data);
192
193 return 0;
194}
195
196static const struct i2c_device_id max6875_id[] = {
197 { "max6875", 0 },
198 { }
199};
200
201static struct i2c_driver max6875_driver = {
202 .driver = {
203 .name = "max6875",
204 },
205 .probe = max6875_probe,
206 .remove = max6875_remove,
207 .id_table = max6875_id,
208};
209
210module_i2c_driver(max6875_driver);
211
212MODULE_AUTHOR("Ben Gardner <bgardner@wabtec.com>");
213MODULE_DESCRIPTION("MAX6875 driver");
214MODULE_LICENSE("GPL");